DOT5-LOG-MIB

File: DOT5-LOG-MIB.mib (91382 bytes)

Imported modules

RFC1155-SMI CTRON-MIB-NAMES RFC1213-MIB
RFC-1212

Imported symbols

TimeTicks Counter dot5
DisplayString OBJECT-TYPE

Defined Objects

dot5Rev1 1.3.6.1.4.1.52.4.1.2.1.1
OBJECT IDENTIFIER    

tRing 1.3.6.1.4.1.52.4.1.2.1.1.1
OBJECT IDENTIFIER    

tRingMgmt 1.3.6.1.4.1.52.4.1.2.1.1.1.1
OBJECT IDENTIFIER    

tRingMgmtRing 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1
OBJECT IDENTIFIER    

tRingMgmtRingName 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.1
The ASCII name assigned to this ring. This name defaults to 'Network n', where n is a unique integer value from 1 to n.
OBJECT-TYPE    
  DisplayString SIZE(20)  

tRingMgmtStnPortCount 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.2
Returns the total number of physical ports on this ring which may be controlled by this device.
OBJECT-TYPE    
  INTEGER  

tRingMgmtRingPortCount 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.3
Returns the total number of ring in/out ports on this ring which may be controlled by this device.
OBJECT-TYPE    
  INTEGER  

tRingMgmtStnPortsEnable 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.4
Setting this object to enable will cause all the station ports on the ring which may be controlled by this device to be enabled. Setting this object to noEnable will have no effect. When read this object will always return noEnable.
OBJECT-TYPE    
  INTEGER noEnable(1), enable(2)  

tRingMgmtRingPortsEnable 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.5
Setting this object to enable will cause all the ring in/out ports on the ring which may be controlled by this device to be enabled. Setting this object to noEnable will have no effect. When read this object will always return noEnable.
OBJECT-TYPE    
  INTEGER noEnable(1), enable(2)  

tRingMgmtStnPortsOn 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.6
Returns the total number of enabled station ports on this ring which may be controlled by this device.
OBJECT-TYPE    
  INTEGER  

tRingMgmtRingPortsOn 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.7
Returns the total number of enabled ring in/out ports on this ring which may be controlled by this device.
OBJECT-TYPE    
  INTEGER  

tRingMgmtStations 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.8
Returns the number of stations currently inserted on the ring, if known (includes this device). If not known, returns zero.
OBJECT-TYPE    
  INTEGER  

tRingMgmtRingState 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.9
Returns the operational state of the ring, if known.
OBJECT-TYPE    
  INTEGER unknown(1), closed(2), normalTokenProtocols(3), purge(4), contention(5), beaconing(6), lobeFail(7), ringPollFailure(8)  

tRingMgmtRingSpeed 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.10
Returns the ring speed of the ring, if known. The speed is designated by the value returned: unknown..............0 fourMegaBits.........4 sixteenMegaBits.....16
OBJECT-TYPE    
  INTEGER  

tRingMgmtActiveMonitor 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.11
Returns the address of the active monitor on this ring, if known. If unknown, the NULL address (00-00-00-00-00-00) is returned.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

tRingMgmtRingNumber 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.12
A read of this object returns the ring number of the attached ring. If the ring number is indeterminate, a zero is returned.
OBJECT-TYPE    
  INTEGER  

tRingMgmtBeaconRecovery 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.13
This object controls the operation of beacon recovery. A write of disable to this object will cause the beacon recovery process to become inactive on this host. A write of enable will cause the beacon recovery process to become active. If beacon recovery is inoperable on the managing device this object will return 'BADSETINFO'. A read of this object will return the current value of this object, reflecting either the last request made or, in the case of a device which is unable to manage beacon recovery, invalid. This object either defaults to enabled or invalid, depending on whether the device can or cannot manage beacon recovery.
OBJECT-TYPE    
  INTEGER disable(1), enable(2), invalid(3)  

tRingMgmtBcnRecRingPortRetryCount 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.14
This object defines the number of times a token ring ring port will be re-enabled after it has been determined that the port is causing the ring to beacon. Values other than 0-100 and 999 will result in MIB bad value. Default of object is product dependent. Refer to individual product documentation. Valid integer values are defined as: 0 ...disable ring port retries 1 - 100 ...retry ring port n times 999 ... retry ring port infinite times
OBJECT-TYPE    
  INTEGER 0..999  

tRingMgmtBcnRecRingPortRetryDelay 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.15
This object defines the time delay between disabling a token ring ring port due to beaconing and re-enabling the port to check the state of the ring port. Setting this object to zero disables retry queue. Non-zero value is delay in seconds. Some products have resolutions that will round this value (in seconds) to the nearest multiple of 7 seconds. Default of object is product dependent. Refer to individual product documentation.
OBJECT-TYPE    
  INTEGER 0..999  

tRingMgmtBcnRecStnPortRetryCount 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.16
This object defines the number of times a token ring station port will be re-enabled after it has been determined that the port is causing the ring to beacon. Values other than 0-100 and 999 will result in MIB bad value. Default of object is product dependent. Refer to individual product documentation. Valid integer values are defined as: 0 ...disable station port retries 1 - 100 ...retry station port n times 999 ... retry station port infinite times
OBJECT-TYPE    
  INTEGER 0..999  

tRingMgmtBcnRecStnPortRetryDelay 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.17
This object defines the time delay between disabling a token ring station port due to beaconing and re-enabling the port to check the state of the station port. Setting this object to zero disables retry queue. Non-zero value is delay in seconds. Some products have resolutions that will round this value (in seconds) to the nearest multiple of 7 seconds. Default of object is product dependent. Refer to individual product documentation.
OBJECT-TYPE    
  INTEGER 0..999  

tRingMgmtBcnRecBrdBypassRetryCount 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.18
This object defines the number of times a token ring MIM board, having been bypassed by beacon recovery, will be un-bypassed to determine if the MIM board is causing the ring to beacon. Values other than 0-100 and 999 will result in MIB bad value. Valid integer values are defined as: 0 ...disable MIM bypass retries 1 - 100 ...retry MIM board un-bypass n times 999 ...retry MIM board un-bypass infinite times Default value is 1.
OBJECT-TYPE    
  INTEGER 0..999  

tRingMgmtBcnRecBrdBypassRetryDelay 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.19
This object defines the time delay between bypassing a token ring MIM board due to beaconing and re-enabling the MIM board to check the state of the board. Setting this object to zero disables retry queue. Non-zero value is delay in seconds with a delay resolution of 1 second.
OBJECT-TYPE    
  INTEGER 0..100  

tRingMgmtBcnRecBrdWrapRetryCount 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.20
This object defines the number of times a token ring MIM board, having been wrapped left or right by beacon recovery, will be un-wrapped to determine if the MIM board is causing the ring to beacon. Values other than 0-100 and 999 will result in MIB bad value. Valid integer values are defined as: 0 ...disable MIM bypass retries 1 - 100 ...retry MIM board un-bypass n times 999 ...retry MIM board un-bypass infinite times Default value is 1.
OBJECT-TYPE    
  INTEGER 0..999  

tRingMgmtBcnRecBrdWrapRetryDelay 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.21
This object defines the time delay between wrapping a token ring MIM board left or right due to beaconing and un-wrapping the MIM board to check the state of the board. Setting this object to zero disables retry queue. Non-zero value is delay in seconds with a delay resolution of 1 second.
OBJECT-TYPE    
  INTEGER 0..100  

tRingMgmtRingPollRecovery 1.3.6.1.4.1.52.4.1.2.1.1.1.1.1.22
This object controls the operation of ring poll failure recovery. A write of disable to this object will cause the ring poll failure recovery process to become inactive on this host. A write of enable will cause the ring poll failure recovery process to become active. If ring poll failure recovery is inoperable on the managing device this object will return `BADSETINFO'. A read of this object will return the current value of this object, reflecting either the last request made or, in the case of a device which is unable to manage ring poll failure recovery, invalid. This object defaults to enabled.
OBJECT-TYPE    
  INTEGER disable(1), enable(2), invalid(3)  

tRingMgmtStn 1.3.6.1.4.1.52.4.1.2.1.1.1.1.2
OBJECT IDENTIFIER    

tRingMgmtStnTable 1.3.6.1.4.1.52.4.1.2.1.1.1.1.2.1
A list of the stations, by MAC address, participating in the ring poll process of this ring.
OBJECT-TYPE    
  SEQUENCE OF  
    TRingMgmtStnEntry

tRingMgmtStnEntry 1.3.6.1.4.1.52.4.1.2.1.1.1.1.2.1.1
A list of the objects pertaining to a station participating in the ring poll process of this ring.
OBJECT-TYPE    
  TRingMgmtStnEntry  

tRingMgmtStnAddress 1.3.6.1.4.1.52.4.1.2.1.1.1.1.2.1.1.1
Returns the MAC address of the station for which the information in this table pertains.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

tRingMgmtStnName 1.3.6.1.4.1.52.4.1.2.1.1.1.1.2.1.1.2
An ASCII name assigned to this station.
OBJECT-TYPE    
  DisplayString SIZE(20)  

tRingMgmtStnBoard 1.3.6.1.4.1.52.4.1.2.1.1.1.1.2.1.1.3
Returns the slot number of the Token Ring board this station is connected to. Board numbers are given as 1 thru n. If unknown, a zero is returned.
OBJECT-TYPE    
  INTEGER  

tRingMgmtStnPort 1.3.6.1.4.1.52.4.1.2.1.1.1.1.2.1.1.4
Returns the port number of the port on the Token Ring board this station is connected to. Port numbers are given as 1 thru n. If unknown, a zero is returned.
OBJECT-TYPE    
  INTEGER  

tRingMgmtStnUNA 1.3.6.1.4.1.52.4.1.2.1.1.1.1.2.1.1.5
Returns the address of the station's nearest upstream neighbor. If unknown, the NULL address (00-00-00-00-00-00) is returned.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

tRingMgmtStnDNA 1.3.6.1.4.1.52.4.1.2.1.1.1.1.2.1.1.6
Returns the address of the station's nearest downstream neighbor. If unknown, the NULL address (00-00-00-00-00-00) is returned.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

tRingMgmtStnPhysLocation 1.3.6.1.4.1.52.4.1.2.1.1.1.1.2.1.1.7
A read of this object returns the physical location of the station. A write of this object assigns a user-defined value indicative of the physical location, or drop, of the station. If the location is unknown or cannot be determined, a zero is returned.
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

tRingMgmtStnFuncClasses 1.3.6.1.4.1.52.4.1.2.1.1.1.1.2.1.1.8
A read of this object returns the station's enabled function class mask.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

tRingMgmtStnPriority 1.3.6.1.4.1.52.4.1.2.1.1.1.1.2.1.1.9
A read of this object returns the station's maximum access priority.
OBJECT-TYPE    
  INTEGER 0..6  

tRingMgmtStnRemoveStn 1.3.6.1.4.1.52.4.1.2.1.1.1.1.2.1.1.10
A write of remove to this object will cause the station to remove itself from the ring. A write of noRemove will do nothing. A read of this object will return the last request made.
OBJECT-TYPE    
  INTEGER noRemove(1), remove(2)  

tRingMgmtHost 1.3.6.1.4.1.52.4.1.2.1.1.1.1.3
OBJECT IDENTIFIER    

tRingMgmtHostCommands 1.3.6.1.4.1.52.4.1.2.1.1.1.1.3.1
A write to this object performs the indicated command. Either of the reset commands will reset the adapter using default parameters and both imply re-insertion onto the ring. A read of this object will return the last command issued to the adapter.
OBJECT-TYPE    
  INTEGER nop(1), hwReset(2), swReset(3), open(4), close(5)  

tRingMgmtHostOpenStatus 1.3.6.1.4.1.52.4.1.2.1.1.1.1.3.2
A read of this object will return the result of the last open command issued to the adapter.
OBJECT-TYPE    
  INTEGER noOpen(1), badParam(2), lobeTestFailed(3), signalLoss(4), insertionTimeout(5), ringFailed(6), beaconing(7), duplicateMACAddress(8), requestFailed(9), removeReceived(10), open(11)  

tRingMgmtHostErrorStatus 1.3.6.1.4.1.52.4.1.2.1.1.1.1.3.3
A read of this object will return the last error status returned by the adapter. The status is the sum of the applicable error codes listed below: No Problem Detected..................0 Ring Recovery.......................32 Single Station......................64 Counter Overflow...................128 Remove Received....................256 Auto-removal Error................1024 Lobe Wire Fault...................2048 Transmit Beacon...................4096 Soft Error........................8192 Hard Error.......................16384 Signal Loss......................32768 No Status, Open Not Completed...131072
OBJECT-TYPE    
  INTEGER  

tRingMgmtHostAMContention 1.3.6.1.4.1.52.4.1.2.1.1.1.1.3.4
A write to this object will either allow the adapter to participate in the active monitor contention process or not. A read of this object will return the setting of this object.
OBJECT-TYPE    
  INTEGER noContentionAllowed(1), contentionAllowed(2)  

tRingMgmtHostTErrorReport 1.3.6.1.4.1.52.4.1.2.1.1.1.1.3.5
A read of this object returns the host's error report timer value. The default timer value is defined as two seconds by the adapter's manufacturer.
OBJECT-TYPE    
  INTEGER  

tRingMgmtHostLocalAdminMac 1.3.6.1.4.1.52.4.1.2.1.1.1.1.3.6
A read of this object returns the MAC address assigned to the interface attached to this network. A write of this object provides for a locally administered MAC address.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

tRingMgmtSecurity 1.3.6.1.4.1.52.4.1.2.1.1.1.1.4
OBJECT IDENTIFIER    

tRingMgmtSecurityAdminState 1.3.6.1.4.1.52.4.1.2.1.1.1.1.4.1
A write to this object will either disable the security feature, enable Station Added trap being sent, or enable security withecurity feature with the remove station MAC frame being sent in addition to sending the Station Removed trap. A read of this object will return the setting of this object.
OBJECT-TYPE    
  INTEGER disable(1), enableWithAlarm(2), enableWithRemoveAndAlarm(3)  

tRingMgmtSecurityAddressAdd 1.3.6.1.4.1.52.4.1.2.1.1.1.1.4.2
A write to this object will add a station's MAC address to the current secure station list within the device. The source routing bit within the MAC address is ignored. If the security list has reached its maximum number of entries, a BAD_VALUE error is returned. A read of this object will return a MAC address of 00-00-00-00-00-00.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

tRingMgmtSecurityAddressRemove 1.3.6.1.4.1.52.4.1.2.1.1.1.1.4.3
A write to this object will remove a station's MAC address from the current secure station list within the device. The source routing bit within the MAC address is ignored. If a station is not found on the list, a BAD_VALUE error is returned. A read of this object will return a MAC address of 00-00-00-00-00-00.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

tRingMgmtSecurityStnCount 1.3.6.1.4.1.52.4.1.2.1.1.1.1.4.4
Returns the number of stations on the secure station list.
OBJECT-TYPE    
  INTEGER  

tRingMgmtSecurityTable 1.3.6.1.4.1.52.4.1.2.1.1.1.1.4.5
The list of secure stations allowed on the ring.
OBJECT-TYPE    
  SEQUENCE OF  
    TRingMgmtSecurityEntry

tRingMgmtSecurityEntry 1.3.6.1.4.1.52.4.1.2.1.1.1.1.4.5.1
A list of objects pertaining to a station allowed on this ring.
OBJECT-TYPE    
  TRingMgmtSecurityEntry  

tRingMgmtSecurityIfIndex 1.3.6.1.4.1.52.4.1.2.1.1.1.1.4.5.1.1
A read of this object will return the MIB-II ifIndex to the ring interface the station referenced by this MAC Address was seen on.
OBJECT-TYPE    
  INTEGER  

tRingMgmtSecurityStnAddress 1.3.6.1.4.1.52.4.1.2.1.1.1.1.4.5.1.2
Returns the MAC address of the station on the secure station list
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

tRingStats 1.3.6.1.4.1.52.4.1.2.1.1.1.2
OBJECT IDENTIFIER    

tRingStatsRing 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1
OBJECT IDENTIFIER    

tRingStatsRingErrs 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1
OBJECT IDENTIFIER    

tRingStatsRingFrames 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.1
Returns the total number of all LLC frames that have passed around this ring. If this value cannot be determined, a zero is returned.
OBJECT-TYPE    
  Counter  

tRingStatsRingKBytes 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.2
Returns the total number of kilobytes from LLC frames that have passed around this ring. If this value cannot be determined, a zero is returned.
OBJECT-TYPE    
  Counter  

tRingStatsRingLineErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.3
Returns the total number of line errors that have occurred on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingBurstErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.4
Returns the total number of burst errors that have occurred on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingACErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.5
Returns the total number of address/copied errors that have occurred on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingAbortSequences 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.6
Returns the total number of abort sequences that have been transmitted on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingInternalErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.7
Returns the number of internal errors that stations on this ring have detected.
OBJECT-TYPE    
  Counter  

tRingStatsRingLostFrames 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.8
Returns the number of lost frames that have been detected on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingCongestErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.9
Returns the number of times stations on this ring have reported receiver congestion errors.
OBJECT-TYPE    
  Counter  

tRingStatsRingFCErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.10
Returns the number of frame copied errors that have occurred on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingTokenErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.11
Returns the number of token errors that have occurred on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingFreqErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.12
Returns the total number of frequency errors on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingTotalErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.13
This object returns the total number of errors reported by the objects in this table (tRingStatsRingErrs 3 thru tRingStatsRingErrs 12) that have occurred on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingAMChanges 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.14
Returns the number of times the active monitor has changed on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingRingPurges 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.15
Returns the number of times the active monitor has purged the ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingBeaconEvents 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.16
Returns the number of times this ring has entered the beaconing state.
OBJECT-TYPE    
  Counter  

tRingStatsRingLongestBeacon 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.17
Returns the length of time in TimeTicks of the longest beaconing state on this ring.
OBJECT-TYPE    
  TimeTicks  

tRingStatsRingLastBeacon 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.18
Returns the length of time in TimeTicks of the last beaconing state on this ring.
OBJECT-TYPE    
  TimeTicks  

tRingStatsRingLastBeaconType 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.19
Returns the type of beaconing frames last seen on the ring.
OBJECT-TYPE    
  INTEGER recoveryModeSet(1), signalLossError(2), streamingSignalNotClaimToken(3), streamingSignalClaimToken(4), noBeaconFramesDetected(5)  

tRingStatsRingPollFailureNoRecovery 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.20
Returns the number of times this ring could not recover from a ring poll failure since the last time this object was reset.
OBJECT-TYPE    
  Counter  

tRingStatsRingPollFailureNNIFrameCount 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.21
Returns the number of times this device has detected Neighbor Notification Incomplete MAC frames on the ring since the last time this object was reset
OBJECT-TYPE    
  Counter  

tRingStatsRingPollFailureNNIFrameAddress 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.22
Returns the MAC address of the ring station that last successfully participated in the ring poll process during and after the ring poll failure process has executed. A value of 00-00-00-00-00-00 indicates that a ring poll has been detected.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

tRingStatsRingPollFailureLastNNIFrameTime 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.23
Returns the timestamp of the last time a Neighbor Notification Complete MAC frame was received since the last time this object was reset. A value of zero indicates that no NNI frame was received.
OBJECT-TYPE    
  Counter  

tRingStatsRingPollFailureLastDNAAddress 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.1.24
Returns the last known downstream neighbor MAC address of the ring station that was reported in the Neighbor Notification Incomplete MAC frame. A value of 00-00-00-00-00-00 indicates that no NNI frame was yet received.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

tRingStatsRingProtos 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.2
OBJECT IDENTIFIER    

tRingStatsRingProtocolSnaFrames 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.2.1
Returns the count of SNA frames seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingProtocolXnsFrames 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.2.2
Returns the count of XNS frames seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingProtocolTcpIpFrames 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.2.3
Returns the count of TCP/IP frames seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingProtocolBanyanFrames 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.2.4
Returns the count of Banyan frames seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingProtocolIpxFrames 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.2.5
Returns the count of Novell IPX frames seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingProtocolNetbiosFrames 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.2.6
Returns the count of NetBIOS frames seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingProtocolLanNetMgrFrames 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.2.7
Returns the count of LAN Network Manager frames seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingProtocolOtherFrames 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.2.8
Returns the count of all other frame types seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingSizes 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.3
OBJECT IDENTIFIER    

tRingStatsRingFramesizeUpTo63Bytes 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.3.1
Returns the count of frames less than 64 bytes in size seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingFramesize64To127Bytes 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.3.2
Returns the count of frames between 64 bytes and 127 bytes in size seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingFramesize128To255Bytes 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.3.3
Returns the count of frames between 128 bytes and 255 bytes in size seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingFramesize256To511Bytes 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.3.4
Returns the count of frames between 256 bytes and 511 bytes in size seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingFramesize512To1023Bytes 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.3.5
Returns the count of frames between 512 bytes and 1023 bytes in size seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingFramesize1024To2047Bytes 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.3.6
Returns the count of frames between 1024 bytes and 2047 bytes in size seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingFramesize2048To4095Bytes 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.3.7
Returns the count of frames between 2048 bytes and 4095 bytes in size seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsRingFramesize4096AndUpBytes 1.3.6.1.4.1.52.4.1.2.1.1.1.2.1.3.8
Returns the count of frames greater than 4096 bytes in size seen on this ring.
OBJECT-TYPE    
  Counter  

tRingStatsStn 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2
OBJECT IDENTIFIER    

tRingStatsStnTable 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1
A list of statistical objects reported by the stations participating in the ring poll process of this ring.
OBJECT-TYPE    
  SEQUENCE OF  
    TRingStatsStnEntry

tRingStatsStnEntry 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1.1
A list of statistical objects reported by a station which is participating in the ring poll process of this ring.
OBJECT-TYPE    
  TRingStatsStnEntry  

tRingStatsStnAddress 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1.1.1
Returns the MAC address to the station port for which the information in this table pertains.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

tRingStatsStnFrames 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1.1.2
This object returns the total number of LLC frames that have originated from this station.
OBJECT-TYPE    
  Counter  

tRingStatsStnBytes 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1.1.3
Returns the total number of bytes from all LLC frames that have originated from this station.
OBJECT-TYPE    
  Counter  

tRingStatsStnLineErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1.1.4
This object gives the number of line errors that have been detected by the station.
OBJECT-TYPE    
  Counter  

tRingStatsStnBurstErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1.1.5
This object gives the number of burst errors that have been detected by the station.
OBJECT-TYPE    
  Counter  

tRingStatsStnACErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1.1.6
Returns the total number of address/copied errors that that have been detected by the station.
OBJECT-TYPE    
  Counter  

tRingStatsStnAbortSequences 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1.1.7
This object gives the number of abort sequences that have been sent by the station.
OBJECT-TYPE    
  Counter  

tRingStatsStnInternalErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1.1.8
This object gives the number of internal errors that have been detected by the station.
OBJECT-TYPE    
  Counter  

tRingStatsStnLostFrames 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1.1.9
This object gives the number of lost frames that have been detected by the station.
OBJECT-TYPE    
  Counter  

tRingStatsStnCongestErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1.1.10
This object gives the number of congestion errors that have been occurred at the station.
OBJECT-TYPE    
  Counter  

tRingStatsStnFCErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1.1.11
This object gives the number of frame copied errors that have been detected by the station.
OBJECT-TYPE    
  Counter  

tRingStatsStnTokenErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1.1.12
This object gives the number of token errors that have been detected by the station while it was acting as the active monitor.
OBJECT-TYPE    
  Counter  

tRingStatsStnFreqErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1.1.13
This object gives the number of frequency errors that have been detected by the station.
OBJECT-TYPE    
  Counter  

tRingStatsStnErrors 1.3.6.1.4.1.52.4.1.2.1.1.1.2.2.1.1.14
This object returns the sum of all errors reported by this table (tRingStatsStnEntry 4 thru tRingStatsStnEntry 13) that have been detected by this station.
OBJECT-TYPE    
  Counter  

tRingStatsReset 1.3.6.1.4.1.52.4.1.2.1.1.1.2.3
OBJECT IDENTIFIER    

tRingStatsResetCounters 1.3.6.1.4.1.52.4.1.2.1.1.1.2.3.1
This object, when written with the value resetCounters, would reset all of this MIB's counter objects associated with the stations on this ring. This in turn resets all of this MIB's counter objects associated with this ring. Writing this object with the value noResetCounters has no effect. When read, this object returns noResetCounters.
OBJECT-TYPE    
  INTEGER noResetCounters(1), resetCounters(2)  

tRingStatsResetTime 1.3.6.1.4.1.52.4.1.2.1.1.1.2.3.2
This object reports the time in TimeTicks that this ring's statistical counters were last reset via the tRingStatsResetCounters command. If the counters have not been reset, this value is zero.
OBJECT-TYPE    
  TimeTicks  

tRingAlarms 1.3.6.1.4.1.52.4.1.2.1.1.1.3
OBJECT IDENTIFIER    

tRingAlarmsRing 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1
OBJECT IDENTIFIER    

tRingAlarmsRingEnbl 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.1
OBJECT IDENTIFIER    

tRingAlarmsRingTimebase 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.1.1
Get/Set alarm timebase. This timebase is used for all alarms pertaining to this ring (including station alarms). Measured in seconds. Minimum interval (default)...10 secs.
OBJECT-TYPE    
  INTEGER  

tRingAlarmsRingRingPurgesEnable 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.1.2
A write of value 2 will enable the Ring Purges threshold alarm. A write of value 1 will disable this threshold alarm (default).
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

tRingAlarmsRingAMPErrsEnable 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.1.3
A write of value 2 will enable the Active Monitor Error threshold alarm. A write of value 1 will disable this threshold alarm (default).
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

tRingAlarmsRingTokenErrsEnable 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.1.4
A write of value 2 will enable the Token Errors threshold alarm. A write of value 1 will disable this threshold alarm (default).
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

tRingAlarmsRingClaimTknErrsEnable 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.1.5
A write of value 2 will enable the Claim Token Errors threshold alarm. A write of value 1 will disable this threshold alarm (default).
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

tRingAlarmsRingLostFramesEnable 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.1.6
A write of value 2 will enable the Lost Frames threshold alarm. A write of value 1 will disable this threshold alarm (default).
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

tRingAlarmsRingBeaconStateEnable 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.1.7
A write of value 2 will enable the Beacon State threshold alarm. A write of value 1 will disable this threshold alarm (default).
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

tRingAlarmsRingFrameCountEnable 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.1.8
A write of value 2 will enable the total Frame Count threshold alarm. A write of value 1 will disable this threshold alarm (default).
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

tRingAlarmsRingThrsh 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.2
OBJECT IDENTIFIER    

tRingAlarmsRingRingPurgesThreshold 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.2.1
The threshold alarm value for Ring Purges. Valid ranges are 1 to 36000 with a default value of 70.
OBJECT-TYPE    
  INTEGER  

tRingAlarmsRingAMPErrsThreshold 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.2.2
The threshold alarm value for Active Monitor Errors. Valid ranges are 1 to 1800 with a default value of 1.
OBJECT-TYPE    
  INTEGER  

tRingAlarmsRingTokenErrsThreshold 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.2.3
The threshold alarm value for Token Errors. Valid ranges are 5 to 7200 with a default value of 10.
OBJECT-TYPE    
  INTEGER  

tRingAlarmsRingClaimTknThreshold 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.2.4
The threshold alarm value for Claim Tokens. Valid ranges are 1 to 7200 with a default value of 5.
OBJECT-TYPE    
  INTEGER  

tRingAlarmsRingLostFramesThreshold 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.2.5
The threshold alarm value for Lost Frames. Valid ranges are 5 to 7200 with a default value of 10.
OBJECT-TYPE    
  INTEGER  

tRingAlarmsRingBeaconStateThreshold 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.2.6
The threshold alarm value for Beacon States. Valid ranges are 1 to 7200 with a default value of 1.
OBJECT-TYPE    
  INTEGER  

tRingAlarmsRingFrameCountThreshold 1.3.6.1.4.1.52.4.1.2.1.1.1.3.1.2.7
The threshold alarm value for the total Frame Count. Valid ranges are 2430 to 250000 with a default values of 8920 for 4 Mbps and 33890 for 16 Mbps ring speeds.
OBJECT-TYPE    
  INTEGER  

tRingAlarmsStn 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2
OBJECT IDENTIFIER    

tRingAlarmsStnEnbl 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.1
OBJECT IDENTIFIER    

tRingAlarmsStnEnblTable 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.1.1
A list of alarm enabling objects pertaining to the stations participating in the ring poll process on this ring.
OBJECT-TYPE    
  SEQUENCE OF  
    TRingAlarmsStnEnblEntry

tRingAlarmsStnEnblEntry 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.1.1.1
A list of alarm enabling objects pertaining to a station participating in the ring poll process on this ring.
OBJECT-TYPE    
  TRingAlarmsStnEnblEntry  

tRingAlarmsStnEnblAddress 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.1.1.1.1
Returns the address of the station to which the information in this table pertains.
OBJECT-TYPE    
  OCTET STRING  

tRingAlarmsStnEnblLineErrsEnable 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.1.1.1.2
A write of value 2 will enable the Line Errors threshold alarm for this station. A write of value 1 will disable this threshold alarm (default).
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

tRingAlarmsStnEnblInternalErrsEnable 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.1.1.1.3
A write of value 2 will enable the Internal Errors threshold alarm for this station. A write of value 1 will disable this threshold alarm (default).
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

tRingAlarmsStnEnblBurstErrsEnable 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.1.1.1.4
A write of value 2 will enable the Burst Errors threshold alarm for this station. A write of value 1 will disable this threshold alarm (default).
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

tRingAlarmsStnEnblACErrsEnable 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.1.1.1.5
A write of value 2 will enable the Address Recognized/Frame Copied Errors threshold alarm for this station. A write of value 1 will disable this threshold alarm (default).
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

tRingAlarmsStnEnblRcvrCongestEnable 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.1.1.1.6
A write of value 2 will enable the Receiver Congestion threshold alarm for this station. A write of value 1 will disable this threshold alarm (default).
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

tRingAlarmsStnThrsh 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.2
OBJECT IDENTIFIER    

tRingAlarmsStnThrshTable 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.2.1
A list of threshold alarm objects pertaining to the stations participating in the ring poll process on this ring.
OBJECT-TYPE    
  SEQUENCE OF  
    TRingAlarmsStnThrshEntry

tRingAlarmsStnThrshEntry 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.2.1.1
A list of threshold alarm objects pertaining to a station participating in the ring poll process on this ring.
OBJECT-TYPE    
  TRingAlarmsStnThrshEntry  

tRingAlarmsStnThrshAddress 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.2.1.1.1
Returns the address of the station to which the information in this table pertains.
OBJECT-TYPE    
  OCTET STRING  

tRingAlarmsStnThrshLineErrsThreshold 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.2.1.1.2
The threshold alarm value for Line Errors. Valid ranges are 1 to 3600 with a default value of 2.
OBJECT-TYPE    
  INTEGER  

tRingAlarmsStnThrshInternalErrsThreshold 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.2.1.1.3
The threshold alarm value for Internal Errors. Valid ranges are 1 to 3600 with a default value of 1.
OBJECT-TYPE    
  INTEGER  

tRingAlarmsStnThrshBurstErrsThreshold 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.2.1.1.4
The threshold alarm value for Burst Errors. Valid ranges are 5 to 18000 with a default value of 10.
OBJECT-TYPE    
  INTEGER  

tRingAlarmsStnThrshACErrsThreshold 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.2.1.1.5
The threshold alarm value for Address Recognized/Frame Copied Errors. Valid ranges are 1 to 1800 with a default value of 2.
OBJECT-TYPE    
  INTEGER  

tRingAlarmsStnThrshRcvrCongestThreshold 1.3.6.1.4.1.52.4.1.2.1.1.1.3.2.2.1.1.6
The threshold alarm value for Receiver Congestion Errors. Valid ranges are 1 to 90000 with a default value of 124.
OBJECT-TYPE    
  INTEGER  

tRingPortGrp 1.3.6.1.4.1.52.4.1.2.1.1.2
OBJECT IDENTIFIER    

tRingPortGrpTable 1.3.6.1.4.1.52.4.1.2.1.1.2.1
A list of port group management objects which pertains to a collection of port groups making up this ring.
OBJECT-TYPE    
  SEQUENCE OF  
    TRingPortGrpEntry

tRingPortGrpEntry 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1
A list of port group management objects which pertains to a single instance of a port group residing on this ring.
OBJECT-TYPE    
  TRingPortGrpEntry  

tRingPortGrpId 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1.1
Returns an index to a port group for which the information in this table pertains.
OBJECT-TYPE    
  INTEGER  

tRingPortGrpName 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1.2
An ASCII name assigned to this port group. The default name is Board n', where n is a number 1 through n.
OBJECT-TYPE    
  DisplayString SIZE(20)  

tRingPortGrpStnPortCount 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1.3
This object defines the total number of station ports on the addressed board.
OBJECT-TYPE    
  INTEGER  

tRingPortGrpRingPortCount 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1.4
This object defines the total number of ring ports (ring-in or ring-out) on the addressed board.
OBJECT-TYPE    
  INTEGER  

tRingPortGrpStnPortsEnable 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1.5
Setting this object to enable will cause all the station ports in this port group to be enabled. Setting this object to noEnable will have no effect on the station ports in this port group. When read this object will always return noEnable.
OBJECT-TYPE    
  INTEGER noEnable(1), enable(2)  

tRingPortGrpRingPortsEnable 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1.6
Setting this object to enable will cause all the ring ports in this port group to be enabled. Setting this object to noEnable will have no effect on the ring ports in this port group. When read this object will always return noEnable.
OBJECT-TYPE    
  INTEGER noEnable(1), enable(2)  

tRingPortGrpStnPortsOn 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1.7
Returns the total number of enabled station ports in this port group.
OBJECT-TYPE    
  INTEGER  

tRingPortGrpRingPortsOn 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1.8
Returns the total number of enabled ring in/out ports in this port group.
OBJECT-TYPE    
  INTEGER  

tRingPortGrpMode 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1.9
This object defines the mode of the board. In Auto Mode, the board is using its hardware defaults. The default values of the board are all ports enabled, speed selected by the HW jumper on the board, the FNB attempts to attach left and right and not bypassed, ring port phantom current (if applicable) is controlled via a HW switch, and selectable media (if applicable) is managed also via a HW switch. In Management Mode, the hardware defaults may be overridden by network or local management.
OBJECT-TYPE    
  INTEGER managementMode(1), autoMode(2)  

tRingPortGrpSpeed 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1.10
This object sets the speed of the board. On devices with a MAC interface this object is read-only, and will return NO SUCH NAME on write requests.
OBJECT-TYPE    
  INTEGER fourMegaBits(4), sixteenMegaBits(16)  

tRingPortGrpSpeedFault 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1.11
This object reports a ring speed fault.
OBJECT-TYPE    
  INTEGER noFaultDetected(1), faultDetected(2)  

tRingPortGrpSpeedFaultLocation 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1.12
This object indicates the last ring speed fault detection circuit(s) to detect the fault, if there was one.
OBJECT-TYPE    
  INTEGER notApplicable(1), fnb(2), ringIn(3), ringOut(4)  

tRingPortGrpBypassRingPortState 1.3.6.1.4.1.52.4.1.2.1.1.2.1.1.13
This object sets and reports the state of the ring bypass relay on those token ring boards which support the relay.
OBJECT-TYPE    
  INTEGER notApplicable(1), off(2), on(3), illegal(4)  

tRingPort 1.3.6.1.4.1.52.4.1.2.1.1.3
OBJECT IDENTIFIER    

tRingPortMgmt 1.3.6.1.4.1.52.4.1.2.1.1.3.1
OBJECT IDENTIFIER    

tRingPortMgmtTable 1.3.6.1.4.1.52.4.1.2.1.1.3.1.1
A list of port management objects which pertains to a collection of ports in a port group residing on this ring.
OBJECT-TYPE    
  SEQUENCE OF  
    TRingPortMgmtEntry

tRingPortMgmtEntry 1.3.6.1.4.1.52.4.1.2.1.1.3.1.1.1
A list of port management objects which pertains to a single instance of a port in a port group residing on this ring.
OBJECT-TYPE    
  TRingPortMgmtEntry  

tRingPortMgmtPortId 1.3.6.1.4.1.52.4.1.2.1.1.3.1.1.1.1
Returns an index to a port for which the information in this table pertains.
OBJECT-TYPE    
  INTEGER  

tRingPortMgmtPortGrpId 1.3.6.1.4.1.52.4.1.2.1.1.3.1.1.1.2
Returns an index to a port group to which the port belongs for which the information in this table pertains.
OBJECT-TYPE    
  INTEGER  

tRingPortMgmtPortName 1.3.6.1.4.1.52.4.1.2.1.1.3.1.1.1.3
Gets/Sets an ASCII name for this port. The default name for this object is 'Board b, Port p', where b and p are integers 1 through n.
OBJECT-TYPE    
  DisplayString SIZE(20)  

tRingPortMgmtPortAdminState 1.3.6.1.4.1.52.4.1.2.1.1.3.1.1.1.4
Setting this object to enable will cause the port to be enabled. Setting this object to disable will cause the ports to be disabled. When read this object will always return the state of the last request.
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

tRingPortMgmtPortOperState 1.3.6.1.4.1.52.4.1.2.1.1.3.1.1.1.5
Returns the operational state of this port.
OBJECT-TYPE    
  INTEGER notOperational(1), operational(2)  

tRingPortMgmtPortType 1.3.6.1.4.1.52.4.1.2.1.1.3.1.1.1.6
Uniquely defines the station or ring port type. An authoritative identification for a token ring station or ring port type. By convention, this value is allocated within the SMI enterprises subtree (1.3.6.1.4.1), and provides an easy and unambiguous means to determine the type of a token ring station or ring port.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

tRingPortMgmtSpeedFaultDetect 1.3.6.1.4.1.52.4.1.2.1.1.3.1.1.1.7
This object indicates whether a speed fault has been detected at this port. If the HW is incapable of detecting a speed fault at the port, the value notDetectable is returned.
OBJECT-TYPE    
  INTEGER notDetectable(1), noFaultDetected(2), faultDetected(3)  

tRingPortMgmtRingOutEnable 1.3.6.1.4.1.52.4.1.2.1.1.3.1.1.1.8
This object, when written, permits the port to function as either a ring out port or a station port, if available. If this selection is not supported by this port, then any write to this object will return a BADSETINFO error. When read, this object will return the state of the port with respect to this mode of operation. The default state of this object, if available, is disabled; otherwise it is notAvailable.
OBJECT-TYPE    
  INTEGER notAvailable(1), disable(2), enable(3)  

tRingPortStn 1.3.6.1.4.1.52.4.1.2.1.1.3.2
OBJECT IDENTIFIER    

tRingPortStnTable 1.3.6.1.4.1.52.4.1.2.1.1.3.2.1
A list of station port management objects which pertains to a collection of station ports in a port group residing on this ring.
OBJECT-TYPE    
  SEQUENCE OF  
    TRingPortStnEntry

tRingPortStnEntry 1.3.6.1.4.1.52.4.1.2.1.1.3.2.1.1
A list of station port management objects which pertains to a single instance of a station port in a port group residing on this ring.
OBJECT-TYPE    
  TRingPortStnEntry  

tRingPortStnPortId 1.3.6.1.4.1.52.4.1.2.1.1.3.2.1.1.1
Returns an index to a port for which the information in this table pertains.
OBJECT-TYPE    
  INTEGER  

tRingPortStnPortGrpId 1.3.6.1.4.1.52.4.1.2.1.1.3.2.1.1.2
Returns an index to a port group to which the port belongs for which the information in this table pertains.
OBJECT-TYPE    
  INTEGER  

tRingPortStnPortLinkState 1.3.6.1.4.1.52.4.1.2.1.1.3.2.1.1.3
This object reports the link status of a port. The link status indicates the port is detecting a good phantom current.
OBJECT-TYPE    
  INTEGER noLink(1), link(2)  

tRingPortStnPortLinkStateTime 1.3.6.1.4.1.52.4.1.2.1.1.3.2.1.1.4
This object reports the amount of time in TimeTicks since the port's link state last changed.
OBJECT-TYPE    
  TimeTicks  

tRingPortStnPortMapEnable 1.3.6.1.4.1.52.4.1.2.1.1.3.2.1.1.5
A write of mappingEnabled to this object permits a station port to be associated, or mapped, to a station participating in the ring poll process on this ring. A write of mappingDisabled prevents this association from taking place. This object is intended to be used when a network monitoring device, such as Network General's Sniffer (tm), is inserted on a ring but is not actively participating in the ring poll. The default value of this object is mappingEnabled.
OBJECT-TYPE    
  INTEGER mappingEnabled(1), mappingDisabled(2)  

tRingPortStnPortMappedMacAddr 1.3.6.1.4.1.52.4.1.2.1.1.3.2.1.1.6
This object reports the MAC address of the station mapped to this port, if known. If unknown, the NULL address is returned.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

tRingPortStnInsertionTrapEnable 1.3.6.1.4.1.52.4.1.2.1.1.3.2.1.1.7
A write of enabled to this object permits the port inserted and port deinserted traps to be sent when phantom current has been asserted or removed, respectively, on this station port. A write of disabled prevents the traps from being sent. The default state of this object is disabled.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

tRingPortRing 1.3.6.1.4.1.52.4.1.2.1.1.3.3
OBJECT IDENTIFIER    

tRingPortRingTable 1.3.6.1.4.1.52.4.1.2.1.1.3.3.1
A list of ring port management objects which pertains to a collection of ring ports in a port group residing on this ring.
OBJECT-TYPE    
  SEQUENCE OF  
    TRingPortRingEntry

tRingPortRingEntry 1.3.6.1.4.1.52.4.1.2.1.1.3.3.1.1
A list of ring port management objects which pertains to a single instance of a ring port in a port group residing on this ring.
OBJECT-TYPE    
  TRingPortRingEntry  

tRingPortRingPortId 1.3.6.1.4.1.52.4.1.2.1.1.3.3.1.1.1
Returns an index to a port for which the information in this table pertains.
OBJECT-TYPE    
  INTEGER  

tRingPortRingPortGrpId 1.3.6.1.4.1.52.4.1.2.1.1.3.3.1.1.2
Returns an index to a port group to which the port belongs for which the information in this table pertains.
OBJECT-TYPE    
  INTEGER  

tRingPortRingPortClass 1.3.6.1.4.1.52.4.1.2.1.1.3.3.1.1.3
This object returns a code indicating whether the queried ring port is capable of either autowrapping or not, or whether the media type is selectable (implies autowrappability).
OBJECT-TYPE    
  INTEGER noAutowrap(1), autowrap(2), selectable(3)  

tRingPortRingPortMediaSelect 1.3.6.1.4.1.52.4.1.2.1.1.3.3.1.1.4
When written, this object allows for the selection of the media type for this ring port. If the ring port is not selectable and an attempt is made to change the media type, a BADSETINFO error will be returned. When read, this object will return the last selection made unless it is unselectable, in which case noSelection is returned.
OBJECT-TYPE    
  INTEGER noSelection(1), stp(2), fiber(3)  

tRingPortRingFaultStatus 1.3.6.1.4.1.52.4.1.2.1.1.3.3.1.1.5
This object reports the media fault status of a ring port capable of auto-wrapping.
OBJECT-TYPE    
  INTEGER notSupported(1), noFaultDetected(2), faultDetected(3)  

tRingPortRingFaultStateTime 1.3.6.1.4.1.52.4.1.2.1.1.3.3.1.1.6
This object reports the amount of time in TimeTicks since the ring port fault state last changed.
OBJECT-TYPE    
  TimeTicks  

tRingPortRingPhantomCurrent 1.3.6.1.4.1.52.4.1.2.1.1.3.3.1.1.7
When written with the value activatePhantom, this object activates the board's phantom current for the ring port, if applicable. This may be different from the HW switch setting. When written with the value deactivatePhantom, the board removes phantom current for this port, if applicable. This may be different from the HW switch setting. If the port does not support phantom drive, any write to this object will return a BADSETINFO error. When read, this object reports the state of the ring port's phantom drive status, whether enabled, disabled, or not supported.
OBJECT-TYPE    
  INTEGER noPhantomAvailable(1), activatePhantom(2), deactivatePhantom(3)  

tRingPortRingPortType 1.3.6.1.4.1.52.4.1.2.1.1.3.3.1.1.8
This object reports the ring port type.
OBJECT-TYPE    
  INTEGER ringIn(1), ringOut(2)  

tRingIf 1.3.6.1.4.1.52.4.1.2.1.1.4
OBJECT IDENTIFIER    

tRingIfIndex 1.3.6.1.4.1.52.4.1.2.1.1.4.1
A read of this object will return the MIB-II ifIndex to the interface this ring is attached to.
OBJECT-TYPE    
  INTEGER  

Defined Objects

TRingMgmtStnEntry  
SEQUENCE    
  OCTET STRING as tRingMgmtStnAddress  
  DisplayString as tRingMgmtStnName  
  INTEGER as tRingMgmtStnBoard  
  INTEGER as tRingMgmtStnPort  
  OCTET STRING as tRingMgmtStnUNA  
  OCTET STRING as tRingMgmtStnDNA  
  OCTET STRING as tRingMgmtStnPhysLocation  
  OCTET STRING as tRingMgmtStnFuncClasses  
  INTEGER as tRingMgmtStnPriority  
  INTEGER as tRingMgmtStnRemoveStn  

TRingMgmtSecurityEntry  
SEQUENCE    
  INTEGER as tRingMgmtSecurityIfIndex  
  OCTET STRING as tRingMgmtSecurityStnAddress  

TRingStatsStnEntry  
SEQUENCE    
  OCTET STRING as tRingStatsStnAddress  
  Counter as tRingStatsStnFrames  
  Counter as tRingStatsStnBytes  
  Counter as tRingStatsStnLineErrors  
  Counter as tRingStatsStnBurstErrors  
  Counter as tRingStatsStnACErrors  
  Counter as tRingStatsStnAbortSequences  
  Counter as tRingStatsStnInternalErrors  
  Counter as tRingStatsStnLostFrames  
  Counter as tRingStatsStnCongestErrors  
  Counter as tRingStatsStnFCErrors  
  Counter as tRingStatsStnTokenErrors  
  Counter as tRingStatsStnFreqErrors  
  Counter as tRingStatsStnErrors  

TRingAlarmsStnEnblEntry  
SEQUENCE    
  OCTET STRING as tRingAlarmsStnEnblAddress  
  INTEGER as tRingAlarmsStnEnblLineErrsEnable  
  INTEGER as tRingAlarmsStnEnblInternalErrsEnable  
  INTEGER as tRingAlarmsStnEnblBurstErrsEnable  
  INTEGER as tRingAlarmsStnEnblACErrsEnable  
  INTEGER as tRingAlarmsStnEnblRcvrCongestEnable  

TRingAlarmsStnThrshEntry  
SEQUENCE    
  OCTET STRING as tRingAlarmsStnThrshAddress  
  INTEGER as tRingAlarmsStnThrshLineErrsThreshold  
  INTEGER as tRingAlarmsStnThrshInternalErrsThreshold  
  INTEGER as tRingAlarmsStnThrshBurstErrsThreshold  
  INTEGER as tRingAlarmsStnThrshACErrsThreshold  
  INTEGER as tRingAlarmsStnThrshRcvrCongestThreshold  

TRingPortGrpEntry  
SEQUENCE    
  INTEGER as tRingPortGrpId  
  DisplayString as tRingPortGrpName  
  INTEGER as tRingPortGrpStnPortCount  
  INTEGER as tRingPortGrpRingPortCount  
  INTEGER as tRingPortGrpStnPortsEnable  
  INTEGER as tRingPortGrpRingPortsEnable  
  INTEGER as tRingPortGrpStnPortsOn  
  INTEGER as tRingPortGrpRingPortsOn  
  INTEGER as tRingPortGrpMode  
  INTEGER as tRingPortGrpSpeed  
  INTEGER as tRingPortGrpSpeedFault  
  INTEGER as tRingPortGrpSpeedFaultLocation  
  INTEGER as tRingPortGrpBypassRingPortState  

TRingPortMgmtEntry  
SEQUENCE    
  INTEGER as tRingPortMgmtPortId  
  INTEGER as tRingPortMgmtPortGrpId  
  DisplayString as tRingPortMgmtPortName  
  INTEGER as tRingPortMgmtPortAdminState  
  INTEGER as tRingPortMgmtPortOperState  
  OBJECT IDENTIFIER as tRingPortMgmtPortType  
  INTEGER as tRingPortMgmtSpeedFaultDetect  
  INTEGER as tRingPortMgmtRingOutEnable  

TRingPortStnEntry  
SEQUENCE    
  INTEGER as tRingPortStnPortId  
  INTEGER as tRingPortStnPortGrpId  
  INTEGER as tRingPortStnPortLinkState  
  TimeTicks as tRingPortStnPortLinkStateTime  
  INTEGER as tRingPortStnPortMapEnable  
  OCTET STRING as tRingPortStnPortMappedMacAddr  
  INTEGER as tRingPortStnInsertionTrapEnable  

TRingPortRingEntry  
SEQUENCE    
  INTEGER as tRingPortRingPortId  
  INTEGER as tRingPortRingPortGrpId  
  INTEGER as tRingPortRingPortClass  
  INTEGER as tRingPortRingPortMediaSelect  
  INTEGER as tRingPortRingFaultStatus  
  TimeTicks as tRingPortRingFaultStateTime  
  INTEGER as tRingPortRingPhantomCurrent  
  INTEGER as tRingPortRingPortType