
| SNMPv2-CONF | SNMPv2-SMI | SNMPv2-TC |
| dvb | 1.3.6.1.4.1.2696 | ||
| OBJECT IDENTIFIER | |||
| mg | 1.3.6.1.4.1.2696.3 | ||
| OBJECT IDENTIFIER | |||
| tr101290 | 1.3.6.1.4.1.2696.3.2 | ||
| DVB Measurement Group MIB to support TR 101 290. This tr101290 module contains measurements defined in TR 101 290. | |||
| MODULE-IDENTITY | |||
| tr101290Objects | 1.3.6.1.4.1.2696.3.2.1 | ||
| OBJECT IDENTIFIER | |||
| tr101290Control | 1.3.6.1.4.1.2696.3.2.1.1 | ||
| OBJECT IDENTIFIER | |||
| controlNow | 1.3.6.1.4.1.2696.3.2.1.1.1 | ||
| The current date and time at the location of the measurement equipment. It is highly desirable that the offset from UTC should be included. It is possible to set the time and date through this object, but it is expected that most systems will incorporate a more accurate method for doing this. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| controlEventPersistence | 1.3.6.1.4.1.2696.3.2.1.1.2 | ||
| The persistence timer used with Event errors. An Event error test remains in the 'fail' state for this length of time after the occurrence of the Event. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| controlRFSystemTable | 1.3.6.1.4.1.2696.3.2.1.1.3 | ||
| Table which controls the RF modulation expected to be received on each input. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ControlRFSystemEntry | |||
| controlRFSystemEntry | 1.3.6.1.4.1.2696.3.2.1.1.3.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| ControlRFSystemEntry | |||
| rfSystemInputNumber | 1.3.6.1.4.1.2696.3.2.1.1.3.1.1 | ||
| RF input whose mode of operation is to be set | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| rfSystemDelivery | 1.3.6.1.4.1.2696.3.2.1.1.3.1.2 | ||
| The type of signal the instrument should expect at its input. | |||
| OBJECT-TYPE | |||
| DeliverySystemType | |||
| controlSynchronizationTable | 1.3.6.1.4.1.2696.3.2.1.1.4 | ||
| Table reserved for future specification of synchronized timing. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ControlSynchronizationEntry | |||
| controlSynchronizationEntry | 1.3.6.1.4.1.2696.3.2.1.1.4.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| ControlSynchronizationEntry | |||
| controlSynchronizationInputNumber | 1.3.6.1.4.1.2696.3.2.1.1.4.1.1 | ||
| Transport Stream number to which the objects in this row apply. | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| controlSynchronizedTime | 1.3.6.1.4.1.2696.3.2.1.1.4.1.2 | ||
| This object is reserved pending future standardisation of timestamping of Transport Streams. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tr101290Trap | 1.3.6.1.4.1.2696.3.2.1.2 | ||
| OBJECT IDENTIFIER | |||
| trapPrefix | 1.3.6.1.4.1.2696.3.2.1.2.0 | ||
| OBJECT IDENTIFIER | |||
| testFailTrap | 1.3.6.1.4.1.2696.3.2.1.2.0.1 | ||
| This trap is sent when a test which is not associated with a measurement fails. This trap is triggered by the transition of the '...State' or '...TestState' object associated with the test to the 'fail' state from any other state. Transmission of the trap is subject to rate control and to the enable status of each test. | |||
| NOTIFICATION-TYPE | |||
| trapControlOID | |||
| trapControlGenerationTime | |||
| trapControlFailureSummary | |||
| trapInput | |||
| measurementFailTrap | 1.3.6.1.4.1.2696.3.2.1.2.0.2 | ||
| Trap which is sent when a test which is associated with a measurement fails. This trap is triggered by the transition of the '...State' or '...TestState' object associated with the test to the 'fail' state from any other state. Transmission of the trap is subject to rate control and to the enable status of each test. | |||
| NOTIFICATION-TYPE | |||
| trapControlOID | |||
| trapControlGenerationTime | |||
| trapControlMeasurementValue | |||
| trapControlFailureSummary | |||
| trapInput | |||
| measurementUnknownTrap | 1.3.6.1.4.1.2696.3.2.1.2.0.3 | ||
| Trap which is sent when a measurement value becomes unavailable. This trap is triggered by the transition of the '...MeasurementState' object associated with the measurement to the 'unknown' state from any other state. Transmission of the trap is subject to rate control. | |||
| NOTIFICATION-TYPE | |||
| trapControlOID | |||
| trapControlGenerationTime | |||
| trapControlFailureSummary | |||
| trapInput | |||
| trapControlTable | 1.3.6.1.4.1.2696.3.2.1.2.1 | ||
| Table of trap control information for each input | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TrapControlEntry | |||
| trapControlEntry | 1.3.6.1.4.1.2696.3.2.1.2.1.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| TrapControlEntry | |||
| trapControlInputNumber | 1.3.6.1.4.1.2696.3.2.1.2.1.1.1 | ||
| Each Transport Stream input has separate trap control parameters. This object identifies the Transport Stream input to which the trap control parameters apply | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| trapControlOID | 1.3.6.1.4.1.2696.3.2.1.2.1.1.2 | ||
| In the case of a testFailTrap or a measurementFailTrap, this object holds the OID of the '...State' or '...TestState' object whose transition to 'fail' has triggered the trap. In the case of a measurementUnknownTrap, this object holds the OID of the '...MeasurementState' object whose transition to 'unknown' has triggered the trap. This object is present for the formal purpose of defining the variable bindings returned with the traps. It is not accessible for normal reading. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| trapControlGenerationTime | 1.3.6.1.4.1.2696.3.2.1.2.1.1.3 | ||
| In the case of a testFailTrap or a measurementFailTrap, at the moment when the trap is generated, the value of the '...LatestError' object associated with the test which caused the trap is copied here. In the case of a measurementUnknownTrap, the time at which the measurement became unknown is copied here. This object is present for the formal purpose of defining the variable bindings returned with the traps. It is not accessible for normal reading. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| trapControlMeasurementValue | 1.3.6.1.4.1.2696.3.2.1.2.1.1.4 | ||
| At the moment when a measurementFailTrap is generated, the value of this object is set from the '...Value' object associated with the measurement which caused the trap. Where a measurement returns multiple values, the value which is copied here is the one which is compared with the threshold(s) to generate the test result. The measurement units are the same as those of the source object. This object is present for the formal purpose of defining the variable bindings returned with the traps. It is not accessible for normal reading. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| trapControlRateStatus | 1.3.6.1.4.1.2696.3.2.1.2.1.1.5 | ||
| This object is used for rate control of traps, preventing overload of the management network by transmission of an excessive number of traps. The value 'disabled' means that traps are never sent. The value 'enabled' means that a trap will be sent when triggered. When a trap is sent, the agent changes the value of this object to 'enabledThrottled'. In this state the agent will not send any more traps. The agent automatically changes the value back to 'enabled' when the time specified by trapControlPeriod expires. A management application may set the value to 'enabled' at any time, but must never set the value to 'enabledThrottled'. This single status applies to all the trap types, so for example if an agent sends a testFailTrap it will not send a measurementFailTrap until the trapControlPeriod expires. | |||
| OBJECT-TYPE | |||
| RateStatus | |||
| trapControlPeriod | 1.3.6.1.4.1.2696.3.2.1.2.1.1.6 | ||
| An agent will ensure that the interval between sending traps is no shorter than this time period. The management system can override this by setting trapControlRateStatus back to 'enabled' within the time period. | |||
| OBJECT-TYPE | |||
| Unsigned32 | 0..3600000 | ||
| trapControlFailureSummary | 1.3.6.1.4.1.2696.3.2.1.2.1.1.7 | ||
| This bit string contains a summary of all the test failures. If the bit for the test is set to one, that test is in a fail state. When a trap is being generated, the agent should ensure that this information is as up to date as possible, without causing undue delay in sending the trap. | |||
| OBJECT-TYPE | |||
| TestSummary | |||
| trapInput | 1.3.6.1.4.1.2696.3.2.1.2.2 | ||
| The Transport Stream input whose change triggered the current trap. This information can also be obtained by analysing the trapControlOID, but trapInput provides the information directly. This object is present for the formal purpose of defining the variable bindings returned with the traps. It is not accessible for normal reading. | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| tr101290Capability | 1.3.6.1.4.1.2696.3.2.1.3 | ||
| OBJECT IDENTIFIER | |||
| capabilityMIBRevision | 1.3.6.1.4.1.2696.3.2.1.3.1 | ||
| The capabilities of the agent are expressed in relation to a specific revision of the tr101290 MIB module. The date and time here must exactly match one of the revision dates in the MODULE-IDENTITY section of the MIB. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| capabilityTS | 1.3.6.1.4.1.2696.3.2.1.3.5 | ||
| OBJECT IDENTIFIER | |||
| capabilityTSGroup | 1.3.6.1.4.1.2696.3.2.1.3.5.1 | ||
| Specifies the overall availability of the Transport Stream group of tests and measurements, tr101290TS. | |||
| OBJECT-TYPE | |||
| GroupAvailability | |||
| capabilityTSTable | 1.3.6.1.4.1.2696.3.2.1.3.5.2 | ||
| Specifies the individual availability of the Transport Stream group of tests and measurements, tr101290TS. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CapabilityTSEntry | |||
| capabilityTSEntry | 1.3.6.1.4.1.2696.3.2.1.3.5.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| CapabilityTSEntry | |||
| capabilityTSOID | 1.3.6.1.4.1.2696.3.2.1.3.5.2.1.1 | ||
| The object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the test/measurement. Table index components of the object identifier are set to zero, except for those which identify specific tests/measurements. Such index objects always have a syntax which begins 'Index...' in this MIB. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| capabilityTSAvailability | 1.3.6.1.4.1.2696.3.2.1.3.5.2.1.2 | ||
| The availability of a specific test or measurement | |||
| OBJECT-TYPE | |||
| Availability | |||
| capabilityTSPollInterval | 1.3.6.1.4.1.2696.3.2.1.3.5.2.1.3 | ||
| Indicates the interval between updates of the information supplied by this object. | |||
| OBJECT-TYPE | |||
| PollingInterval | |||
| capabilityCableSat | 1.3.6.1.4.1.2696.3.2.1.3.6 | ||
| OBJECT IDENTIFIER | |||
| capabilityCableSatGroup | 1.3.6.1.4.1.2696.3.2.1.3.6.1 | ||
| Specifies the overall availability of the cable and satellite group of tests and measurements, tr101290CableSat. | |||
| OBJECT-TYPE | |||
| GroupAvailability | |||
| capabilityCableSatTable | 1.3.6.1.4.1.2696.3.2.1.3.6.2 | ||
| Specifies the individual availability of the cable and satellite group of tests and measurements, tr101290CableSat. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CapabilityCableSatEntry | |||
| capabilityCableSatEntry | 1.3.6.1.4.1.2696.3.2.1.3.6.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| CapabilityCableSatEntry | |||
| capabilityCableSatOID | 1.3.6.1.4.1.2696.3.2.1.3.6.2.1.1 | ||
| The object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the test/measurement. Table index components of the object identifier are set to zero, except for those which identify specific tests/measurements. Such index objects always have a syntax which begins 'Index...' in this MIB. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| capabilityCableSatAvailability | 1.3.6.1.4.1.2696.3.2.1.3.6.2.1.2 | ||
| The availability of a specific test or measurement | |||
| OBJECT-TYPE | |||
| Availability | |||
| capabilityCableSatPollInterval | 1.3.6.1.4.1.2696.3.2.1.3.6.2.1.3 | ||
| Indicates the interval between updates of the information supplied by this object. | |||
| OBJECT-TYPE | |||
| PollingInterval | |||
| capabilityCable | 1.3.6.1.4.1.2696.3.2.1.3.7 | ||
| OBJECT IDENTIFIER | |||
| capabilityCableGroup | 1.3.6.1.4.1.2696.3.2.1.3.7.1 | ||
| Specifies the overall availability of the cable group of tests and measurements, tr101290Cable. | |||
| OBJECT-TYPE | |||
| GroupAvailability | |||
| capabilityCableTable | 1.3.6.1.4.1.2696.3.2.1.3.7.2 | ||
| Specifies the individual availability of the cable group of tests and measurements, tr101290Cable. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CapabilityCableEntry | |||
| capabilityCableEntry | 1.3.6.1.4.1.2696.3.2.1.3.7.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| CapabilityCableEntry | |||
| capabilityCableOID | 1.3.6.1.4.1.2696.3.2.1.3.7.2.1.1 | ||
| The object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the test/measurement. Table index components of the object identifier are set to zero, except for those which identify specific tests/measurements. Such index objects always have a syntax which begins 'Index...' in this MIB. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| capabilityCableAvailability | 1.3.6.1.4.1.2696.3.2.1.3.7.2.1.2 | ||
| The availability of a specific test or measurement | |||
| OBJECT-TYPE | |||
| Availability | |||
| capabilityCablePollInterval | 1.3.6.1.4.1.2696.3.2.1.3.7.2.1.3 | ||
| Indicates the interval between updates of the information supplied by this object. | |||
| OBJECT-TYPE | |||
| PollingInterval | |||
| capabilitySatellite | 1.3.6.1.4.1.2696.3.2.1.3.8 | ||
| OBJECT IDENTIFIER | |||
| capabilitySatelliteGroup | 1.3.6.1.4.1.2696.3.2.1.3.8.1 | ||
| Specifies the overall availability of the satellite group of tests and measurements, tr101290Satellite. | |||
| OBJECT-TYPE | |||
| GroupAvailability | |||
| capabilitySatelliteTable | 1.3.6.1.4.1.2696.3.2.1.3.8.2 | ||
| Specifies the individual availability of the satellite group of tests and measurements, tr101290Satellite. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CapabilitySatelliteEntry | |||
| capabilitySatelliteEntry | 1.3.6.1.4.1.2696.3.2.1.3.8.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| CapabilitySatelliteEntry | |||
| capabilitySatelliteOID | 1.3.6.1.4.1.2696.3.2.1.3.8.2.1.1 | ||
| The object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the test/measurement. Table index components of the object identifier are set to zero, except for those which identify specific tests/measurements. Such index objects always have a syntax which begins 'Index...' in this MIB. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| capabilitySatelliteAvailability | 1.3.6.1.4.1.2696.3.2.1.3.8.2.1.2 | ||
| The availability of a specific test or measurement | |||
| OBJECT-TYPE | |||
| Availability | |||
| capabilitySatellitePollInterval | 1.3.6.1.4.1.2696.3.2.1.3.8.2.1.3 | ||
| Indicates the interval between updates of the information supplied by this object. | |||
| OBJECT-TYPE | |||
| PollingInterval | |||
| capabilityTerrestrial | 1.3.6.1.4.1.2696.3.2.1.3.9 | ||
| OBJECT IDENTIFIER | |||
| capabilityTerrestrialGroup | 1.3.6.1.4.1.2696.3.2.1.3.9.1 | ||
| Specifies the overall availability of the terrestrial group of tests and measurements, tr101290Terrestrial. | |||
| OBJECT-TYPE | |||
| GroupAvailability | |||
| capabilityTerrestrialTable | 1.3.6.1.4.1.2696.3.2.1.3.9.2 | ||
| Specifies the individual availability of the terrestrial group of tests and measurements, tr101290Terrestrial. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CapabilityTerrestrialEntry | |||
| capabilityTerrestrialEntry | 1.3.6.1.4.1.2696.3.2.1.3.9.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| CapabilityTerrestrialEntry | |||
| capabilityTerrestrialOID | 1.3.6.1.4.1.2696.3.2.1.3.9.2.1.1 | ||
| The object identifier of a specific test/measurement. The object identifier of the object within the table whose SYNTAX is 'TestState' is used to identify the test/measurement. Table index components of the object identifier are set to zero, except for those which identify specific tests/measurements. Such index objects always have a syntax which begins 'Index...' in this MIB. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| capabilityTerrestrialAvailability | 1.3.6.1.4.1.2696.3.2.1.3.9.2.1.2 | ||
| The availability of a specific test or measurement | |||
| OBJECT-TYPE | |||
| Availability | |||
| capabilityTerrestrialPollInterval | 1.3.6.1.4.1.2696.3.2.1.3.9.2.1.3 | ||
| Indicates the interval between updates of the information supplied by this object. | |||
| OBJECT-TYPE | |||
| PollingInterval | |||
| tr101290TS | 1.3.6.1.4.1.2696.3.2.1.5 | ||
| OBJECT IDENTIFIER | |||
| tsTests | 1.3.6.1.4.1.2696.3.2.1.5.2 | ||
| OBJECT IDENTIFIER | |||
| tsTestsSummaryTable | 1.3.6.1.4.1.2696.3.2.1.5.2.2 | ||
| The tsTestsSummaryTable provides access to the state of all of the Transport Stream tests enumerated in IndexTransportStreamTest. The status relates to the whole Transport Stream. In the case of tests which have a status per PID, the tsTestsSummaryTable gives the 'worst' status across all the PIDs and the status for each PID is available in tsTestsPIDTable. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TsTestsSummaryEntry | |||
| tsTestsSummaryEntry | 1.3.6.1.4.1.2696.3.2.1.5.2.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| TsTestsSummaryEntry | |||
| tsTestsSummaryInputNumber | 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.1 | ||
| Transport Stream on which the test is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| tsTestsSummaryTestNumber | 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.2 | ||
| Specifies the test, see definition of IndexTransportStreamTest. Rows in the table exist only for tests which are actually implemented by the measuring equipment. | |||
| OBJECT-TYPE | |||
| IndexTransportStreamTest | |||
| tsTestsSummaryState | 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.3 | ||
| This gives the overall pass/fail state of the test. For tests which have a state per PID, tsTestsSummaryState contains the highest numeric value of all the tsTestsPIDState objects for the test. | |||
| OBJECT-TYPE | |||
| TestState | |||
| tsTestsSummaryEnable | 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.4 | ||
| Determines whether this test and associated traps are enabled. Setting tsTestsSummaryEnable affects tsTestsPIDEnable in tsTestsPIDTable. When tsTestsSummaryEnable is set, all existing instances of tsTestsPIDEnable are set to the same value. Any new rows in tsTestsPIDTable which are created will also have this value for tsTestsPIDEnable (unless the row is created by explicitly setting the value of tsTestsPIDEnable). | |||
| OBJECT-TYPE | |||
| Enable | |||
| tsTestsSummaryCounter | 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.5 | ||
| Count of the number of times this error has occurred. For Status errors this is the number of times the TestState has entered the fail state from some other state. For Error events this is the total number of events; the persistence timer is not taken into account by the counter. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| tsTestsSummaryCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.6 | ||
| Provides the last time at which there was a discontinuity in the tsTestsSummaryCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsTestsSummaryCounterReset | 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.7 | ||
| tsTestsSummaryCounter is reset to zero and tsTestsSummaryCounterDiscontinuity is set to the current time if this object is set to 'true'. This object has no effect on the tsTestsPIDCounter objects. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| tsTestsSummaryLatestError | 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.8 | ||
| The timestamp at the most recent occurrence of the error. For Status errors this is the most recent time the TestState entered the fail state from some other state. For Error events this is the most recent occurrence; the persistence timer is not taken into account. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsTestsSummaryActiveTime | 1.3.6.1.4.1.2696.3.2.1.5.2.2.1.9 | ||
| The total time when it has been possible to evaluate this test. | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| tsTestsPIDTable | 1.3.6.1.4.1.2696.3.2.1.5.2.3 | ||
| The tsTestsPIDTable provides access to the state of those Transport Stream tests enumerated in IndexTransportStreamTest which relate to individual PIDs. These tests are: 1.4 Continuity_count_error 1.5.a PMT_error_2 1.6 PID_error 2.3.a PCR_repetition_error 2.3.b PCR_discontinuity_indicator_error 2.4 PCR_accuracy_error 2.5 PTS_error 3.3 Buffer_error 3.4.a Unreferenced_PID | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TsTestsPIDEntry | |||
| tsTestsPIDEntry | 1.3.6.1.4.1.2696.3.2.1.5.2.3.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| TsTestsPIDEntry | |||
| tsTestsPIDInputNumber | 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.1 | ||
| Transport Stream on which the test is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| tsTestsPIDPID | 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.2 | ||
| PID (plus one) on which the test is made | |||
| OBJECT-TYPE | |||
| PIDPlusOne | |||
| tsTestsPIDTestNumber | 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.3 | ||
| Specifies the test, see definition of IndexTransportStreamTest. Rows in the table exist only for tests which are actually implemented by the measuring equipment. | |||
| OBJECT-TYPE | |||
| IndexTransportStreamTest | |||
| tsTestsPIDRowStatus | 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.4 | ||
| This is used by the manager to create and delete rows in tsTestsPIDTable. The agent automatically creates rows for PID/test combinations where there are errors to report. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| tsTestsPIDState | 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.5 | ||
| This gives the overall pass/fail state of the test | |||
| OBJECT-TYPE | |||
| TestState | |||
| tsTestsPIDEnable | 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.6 | ||
| Determines whether this test and associated traps are enabled. When a trap triggering condition arises for a per PID test, this object alone is used to determine whether a trap will be generated, without any reference to tsTestsSummaryEnable. | |||
| OBJECT-TYPE | |||
| Enable | |||
| tsTestsPIDCounter | 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.7 | ||
| Count of the number of times this error has occurred. For Status errors this is the number of times the TestState has entered the fail state from some other state. For Error events this is the total number of events; the persistence timer is not taken into account by the counter. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| tsTestsPIDCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.8 | ||
| Provides the last time at which there was a discontinuity in the tsTestsSummaryCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsTestsPIDCounterReset | 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.9 | ||
| tsTestsPIDCounter is reset to zero and tsTestsPIDCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| tsTestsPIDLatestError | 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.10 | ||
| The timestamp at the most recent occurrence of the error. For Status errors this is the most recent time the TestState entered the fail state from some other state. For Error events this is the most recent occurrence; the persistence timer is not taken into account. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsTestsPIDActiveTime | 1.3.6.1.4.1.2696.3.2.1.5.2.3.1.11 | ||
| The total time when it has been possible to evaluate this test. | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| tsTestsPreferences | 1.3.6.1.4.1.2696.3.2.1.5.2.100 | ||
| OBJECT IDENTIFIER | |||
| tsTestsPreferencesTable | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1 | ||
| This table contains measurement thresholds and other configuration information that is applied on a per Transport Stream basis. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TsTestsPreferencesEntry | |||
| tsTestsPreferencesEntry | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| TsTestsPreferencesEntry | |||
| tsTestsPrefInputNumber | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.1 | ||
| Transport Stream input to which the preferences apply | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| tsTestsPrefTransitionDuration | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.2 | ||
| Various tests, including CAT_error (2.6) and Unreferenced_PID (3.4) must take into account that short transition periods can exist where the state of the SI and PSI information is inconsistent with the state of the stream. These transitions should not cause error indications. This parameter specifies the period which must be allowed for transition states. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefPATSectionIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.3 | ||
| Maximum repetition interval for PAT sections. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefPMTSectionIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.4 | ||
| Maximum repetition interval for PMT sections. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefReferredIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.5 | ||
| Maximum permitted interval between the arrival of consecutive packets for all PIDs. When the value of this object is set, the value of tsTestsPrefPIDReferredIntervalMax is changed for every PID. The value of this object is also used as a default for tsTestsPrefPIDReferredIntervalMax when a new row is created in tsTestsPreferencesPIDTable. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefPCRIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.6 | ||
| Maximum permitted interval between PCR arrival times on each PCR PID. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefPCRDiscontinuityMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.7 | ||
| Maximum permitted difference between two consecutive PCR values. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefPCRInaccuracyMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.8 | ||
| Maximum permitted PCR inaccuracy. An error is indicated if the PCR inaccuracy is outside the range: [-tsTestsPrefPCRInaccuracyMax .. +tsTestsPrefPCRInaccuracyMax]. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefPTSIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.9 | ||
| Maximum permitted PTS repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefNITActualIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.10 | ||
| Maximum permitted NIT_actual section repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefNITActualIntervalMin | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.11 | ||
| Minimum permitted NIT_actual section repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefNITOtherIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.12 | ||
| Maximum permitted NIT_other section repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefSIGapMin | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.13 | ||
| Minimum permitted gap between packets containing sections. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefNITTableIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.14 | ||
| Maximum permitted NIT table repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefBATTableIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.15 | ||
| Maximum permitted BAT table repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefSDTActualTableIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.16 | ||
| Maximum permitted SDT actual transport stream table repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefSDTOtherTableIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.17 | ||
| Maximum permitted SDT other transport stream table repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefEITPFActualTableIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.18 | ||
| Maximum permitted EIT Present/Following actual transport stream table repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefEITPFOtherTableIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.19 | ||
| Maximum permitted EIT Present/Following other transport stream table repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefEITSActualNearTableIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.20 | ||
| Maximum permitted EIT Schedule actual transport stream table repetition interval for the near future (the next 8 days for satellite and cable, the next day for terrestrial). | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefEITSActualFarTableIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.21 | ||
| Maximum permitted EIT Schedule actual transport stream table repetition interval for the far future (beyond the next 8 days for satellite and cable, beyond the next day for terrestrial). | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefEITSOtherNearTableIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.22 | ||
| Maximum permitted EIT Schedule other transport stream table repetition interval for the near future (the next 8 days for satellite and cable, the next day for terrestrial). | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefEITSOtherFarTableIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.23 | ||
| Maximum permitted EIT Schedule other transport stream table repetition interval for the far future (beyond the next 8 days for satellite and cable, beyond the next day for terrestrial). | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefTxTTableIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.24 | ||
| Maximum permitted TDT and TOT table repetition intervals | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefSDTActualIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.25 | ||
| Maximum permitted SDT_actual section repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefSDTActualIntervalMin | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.26 | ||
| Minimum permitted SDT_actual section repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefSDTOtherIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.27 | ||
| Maximum permitted SDT_other section repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefEITActualIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.28 | ||
| Maximum permitted EIT_actual section repetition interval (applies to both present and following sections). | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefEITActualIntervalMin | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.29 | ||
| Minimum permitted EIT_actual section repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefEITOtherIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.30 | ||
| Maximum permitted EIT_other section repetition interval (applies to both present and following sections). | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefRSTIntervalMin | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.31 | ||
| Minimum permitted RST section repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefTDTIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.32 | ||
| Maximum permitted TDT section repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPrefTDTIntervalMin | 1.3.6.1.4.1.2696.3.2.1.5.2.100.1.1.33 | ||
| Minimum permitted TDT section repetition interval | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTestsPreferencesPIDTable | 1.3.6.1.4.1.2696.3.2.1.5.2.100.2 | ||
| This table contains measurement thresholds and other configuration information that is applied on a per PID per Transport Stream basis. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TsTestsPreferencesPIDEntry | |||
| tsTestsPreferencesPIDEntry | 1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1 | ||
| Description. | |||
| OBJECT-TYPE | |||
| TsTestsPreferencesPIDEntry | |||
| tsTestsPrefPIDInputNumber | 1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.1 | ||
| Transport Stream input to which the preferences apply | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| tsTestsPrefPIDPID | 1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.2 | ||
| PID to which these preferences apply | |||
| OBJECT-TYPE | |||
| PIDPlusOne | |||
| tsTestsPrefPIDRowStatus | 1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.3 | ||
| This object is used to manage the rows in this table. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| tsTestsPrefPIDReferredIntervalMax | 1.3.6.1.4.1.2696.3.2.1.5.2.100.2.1.4 | ||
| Maximum permitted interval between the arrival of consecutive packets of this PID. The default value for this object is the current value of tsTestsPrefReferredIntervalMax for the same input. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsMeasurements | 1.3.6.1.4.1.2696.3.2.1.5.4 | ||
| OBJECT IDENTIFIER | |||
| tsPcrMeasurementTable | 1.3.6.1.4.1.2696.3.2.1.5.4.1 | ||
| This table makes available the PCR_FO, PCR_DR, PCR_OJ and PCR_AC measurements. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TsPcrMeasurementEntry | |||
| tsPcrMeasurementEntry | 1.3.6.1.4.1.2696.3.2.1.5.4.1.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| TsPcrMeasurementEntry | |||
| tsPcrMeasurementInputNumber | 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.1 | ||
| Input on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| tsPcrMeasurementPID | 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.2 | ||
| PID (plus one) in the Transport Stream carrying (or expected to carry) PCRs. | |||
| OBJECT-TYPE | |||
| PIDPlusOne | |||
| tsPcrMeasurementNumber | 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.3 | ||
| This selects one of the four PCR measurements | |||
| OBJECT-TYPE | |||
| IndexPCRMeasurement | |||
| tsPcrMeasurementRowStatus | 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.4 | ||
| This object is used by the manager to create and delete rows in the table. The agent automatically creates rows for PIDs where it detects the presence of a PCR. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| tsPcrMeasurementState | 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.5 | ||
| This gives the overall pass/fail state of the threshold test on this measurement | |||
| OBJECT-TYPE | |||
| TestState | |||
| tsPcrMeasurementEnable | 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.6 | ||
| Determines whether this test and associated traps are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| tsPcrMeasurementCounter | 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.7 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| tsPcrMeasurementCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.8 | ||
| Provides the last time at which there was a discontinuity in the tsPcrMeasurementCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsPcrMeasurementCounterReset | 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.9 | ||
| tsPcrMeasurementCounter is reset to zero and tsPcrMeasurementCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| tsPcrMeasurementLatestError | 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.10 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsPcrMeasurementActiveTime | 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.11 | ||
| The total time when it has been possible to make this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| tsPcrMeasurementMeasurementState | 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.12 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| tsPcrMeasurementValue | 1.3.6.1.4.1.2696.3.2.1.5.4.1.1.13 | ||
| The units for the measured value depend on the measurement: PCR_FO Hz PCR_DR Hz/s Values for PCR_OJ and PCR_AC are not provided as they occur too quickly to be usefully retrieved via SNMP. For these measurements, the MeasurementState is always 'unknown'. However, the threshold tests are expected to work correctly for these measurements. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| bitRate | 1.3.6.1.4.1.2696.3.2.1.5.4.2 | ||
| OBJECT IDENTIFIER | |||
| tsTransportStreamBitRateTable | 1.3.6.1.4.1.2696.3.2.1.5.4.2.1 | ||
| Bit rates for each complete Transport Stream | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TsTransportStreamBitRateEntry | |||
| tsTransportStreamBitRateEntry | 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| TsTransportStreamBitRateEntry | |||
| tsTransportStreamBitRateInputNumber | 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| tsTransportStreamBitRateState | 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.2 | ||
| This gives the overall pass/fail state of the threshold test on this measurement | |||
| OBJECT-TYPE | |||
| TestState | |||
| tsTransportStreamBitRateEnable | 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| tsTransportStreamBitRateCounter | 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| tsTransportStreamBitRateCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.5 | ||
| Provides the last time at which there was a discontinuity in the tsTransportStreamBitRateCounterobject. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsTransportStreamBitRateCounterReset | 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.6 | ||
| tsTransportStreamBitRateCounteris reset to zero and tsTransportStreamBitRateCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| tsTransportStreamBitRateLatestError | 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsTransportStreamBitRateActiveTime | 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| tsTransportStreamBitRateMeasurementState | 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| tsTransportStreamBitRateValue | 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.10 | ||
| The overall Transport Stream bit rate | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsTransportStreamBitRateNomenclature | 1.3.6.1.4.1.2696.3.2.1.5.4.2.1.1.11 | ||
| Standardised description of the method of measurement of the bitrate, for example 'bit/s @MGB2' | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| tsServiceBitRateTable | 1.3.6.1.4.1.2696.3.2.1.5.4.2.2 | ||
| Bit rates for each service/program within each Transport Stream. The table is sparse, in that only services mentioned in the PMT will be present. The bit rate of a service is the sum of the bit rates of the elementary_PID's in its PMT and the CA_PID's in any CA_descriptors in its PMT (ECMs). The bit rate of the PMT itself is excluded. The bit rate of the PCR_PID is excluded unless the PCR_PID is also one of the elementary_PID's in the PMT. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TsServiceBitRateEntry | |||
| tsServiceBitRateEntry | 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| TsServiceBitRateEntry | |||
| tsServiceBitRateInputNumber | 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| tsServiceBitRateService | 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.2 | ||
| The program_number/service_id to which the information in the rest of the row applies. | |||
| OBJECT-TYPE | |||
| ServiceId | |||
| tsServiceBitRateRowStatus | 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.3 | ||
| This is used by the manager to create and delete rows in the table. The agent will automatically create rows for services it finds in the PMT. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| tsServiceBitRateState | 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.4 | ||
| This gives the overall pass/fail state of the threshold test on this measurement | |||
| OBJECT-TYPE | |||
| TestState | |||
| tsServiceBitRateEnable | 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.5 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| tsServiceBitRateCounter | 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.6 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| tsServiceBitRateCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.7 | ||
| Provides the last time at which there was a discontinuity in the tsServiceBitRateCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsServiceBitRateCounterReset | 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.8 | ||
| tsServiceBitRateCounter is reset to zero and tsServiceBitRateCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| tsServiceBitRateLatestError | 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.9 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsServiceBitRateActiveTime | 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.10 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| tsServiceBitRateMeasurementState | 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.11 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| tsServiceBitRateValue | 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.12 | ||
| Overall bit rate for the service | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsServiceBitRateNomenclature | 1.3.6.1.4.1.2696.3.2.1.5.4.2.2.1.13 | ||
| Standardised description of the method of measurement of the bitrate, for example 'bit/s @MGB2' | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| tsPIDBitRateTable | 1.3.6.1.4.1.2696.3.2.1.5.4.2.3 | ||
| Bit rates for each PID within each Transport Stream. The table is sparse, in that only PIDs whose bit rate is currently greater than zero will be present in the table. This allows for faster traversal of the table to build up a list of PID bit rates. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TsPIDBitRateEntry | |||
| tsPIDBitRateEntry | 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| TsPIDBitRateEntry | |||
| tsPIDBitRateInputNumber | 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| tsPIDBitRatePID | 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.2 | ||
| PID whose bit rate is being measured (plus one) | |||
| OBJECT-TYPE | |||
| PIDPlusOne | |||
| tsPIDBitRateRowStatus | 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.3 | ||
| This is used by the manager to create and delete rows in the table. The agent will automatically create rows for PIDs whose bit rate is non-zero. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| tsPIDBitRateState | 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.4 | ||
| This gives the overall pass/fail state of the threshold test on this measurement | |||
| OBJECT-TYPE | |||
| TestState | |||
| tsPIDBitRateEnable | 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.5 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| tsPIDBitRateCounter | 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.6 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| tsPIDBitRateCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.7 | ||
| Provides the last time at which there was a discontinuity in the tsPIDBitRateCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsPIDBitRateCounterReset | 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.8 | ||
| tsPIDBitRateCounter is reset to zero and tsPIDBitRateCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| tsPIDBitRateLatestError | 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.9 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsPIDBitRateActiveTime | 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.10 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| tsPIDBitRateMeasurementState | 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.11 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| tsPIDBitRateValue | 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.12 | ||
| Bit rate for the PID. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsPIDBitRateNomenclature | 1.3.6.1.4.1.2696.3.2.1.5.4.2.3.1.13 | ||
| Standardised description of the method of measurement of the bitrate, for example 'bit/s @MGB2' | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| tsConsistencyTable | 1.3.6.1.4.1.2696.3.2.1.5.4.3 | ||
| This table provides the result of the Transport Stream consistency test for each input. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TsConsistencyEntry | |||
| tsConsistencyEntry | 1.3.6.1.4.1.2696.3.2.1.5.4.3.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| TsConsistencyEntry | |||
| tsConsistencyInputNumber | 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.1 | ||
| Input (Transport Stream) on which the consistency check is made. | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| tsConsistencyTestNumber | 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.2 | ||
| Specifies the consistency check test | |||
| OBJECT-TYPE | |||
| IndexConsistencyTest | |||
| tsConsistencyState | 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.3 | ||
| This gives the overall pass/fail state of the consistency check. | |||
| OBJECT-TYPE | |||
| TestState | |||
| tsConsistencyEnable | 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.4 | ||
| Determines whether this test and associated traps are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| tsConsistencyCounter | 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.5 | ||
| Count of the number of times the consistency check has failed. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| tsConsistencyCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.6 | ||
| Provides the last time at which there was a discontinuity in the tsConsistencyCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsConsistencyCounterReset | 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.7 | ||
| tsConsistencyCounter is reset to zero and tsConsistencyCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| tsConsistencyLatestError | 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.8 | ||
| The timestamp at the most recent failure of the consistency check. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsConsistencyActiveTime | 1.3.6.1.4.1.2696.3.2.1.5.4.3.1.9 | ||
| The total time when it has been possible to perform this test | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| tsMeasurePreferences | 1.3.6.1.4.1.2696.3.2.1.5.4.100 | ||
| OBJECT IDENTIFIER | |||
| tsMeasurePreferencesTable | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1 | ||
| This table contains configuration information for the tsMeasurements branch of the MIB. Configuration related to the whole Transport Stream is found here. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TsMeasurePreferencesEntry | |||
| tsMeasurePreferencesEntry | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| TsMeasurePreferencesEntry | |||
| tsMeasurePrefInputNumber | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.1 | ||
| Transport Stream input to which the preferences apply | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| tsMeasurePrefPCRDemarcationFrequency | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.2 | ||
| This is the demarcation frequency used by the PCR measurement system to distinguish between inaccuracy/jitter and drift. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsMeasurePrefPCRFOMax | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.3 | ||
| Maximum permitted PCR_FO (frequency offset). An error is indicated if the measured PCR_FO is outside the range [-tsMeasurePrefPCRFOMax .. +tsMeasurePrefPCRFOMax]. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsMeasurePrefPCRDRMax | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.4 | ||
| Maximum permitted PCR_DR (drift rate). An error is indicated if the measured PCR_DR is outside the range [-tsMeasurePrefPCRDRMax .. +tsMeasurePrefPCRDRMax] | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsMeasurePrefPCROJMax | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.5 | ||
| Maximum permitted PCR_OJ (overall jitter). An error is indicated if the measured PCR_OJ is outside the range [-tsMeasurePrefPCROJMax .. +tsMeasurePrefPCROJMax] | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsMeasurePrefTSBitRateTau | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.6 | ||
| 'tau' value for Transport Stream bit rate measurement. The MIB provides very flexible ways of setting the bit rate measurement parameters tau, N and element for the Transport Stream, services, PIDs and for individual services and PIDs. Real measurement equipment can be expected to provide much less flexibility. Management software should anticipate this by either being statically aware of the capabilities of the agent or by checking that preference settings have been accepted by reading them back after each attempt to set them. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsMeasurePrefTSBitRateN | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.7 | ||
| 'N' value for Transport Stream bit rate measurement. See note in description for tsMeasurePrefTSBitRateTau. | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| tsMeasurePrefTSBitRateElement | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.8 | ||
| Data unit which is counted by the bit rate measurement algorithm. See note in description for tsMeasurePrefTSBitRateTau. | |||
| OBJECT-TYPE | |||
| BitRateElement | |||
| tsMeasurePrefTSBitRateMin | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.9 | ||
| An error is generated if the Transport Stream bit rate is below this value. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsMeasurePrefTSBitRateMax | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.10 | ||
| An error is generated if the Transport Stream bit rate exceeds this value. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsMeasurePrefAllServiceBitRateTau | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.11 | ||
| 'tau' value for Service bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefServiceBitRateTau columns in all the rows of the tsMeasurePreferencesServiceTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsMeasurePrefAllServiceBitRateN | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.12 | ||
| 'N' value for Service bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefServiceBitRateN columns in all the rows of the tsMeasurePreferencesServiceTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau. | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| tsMeasurePrefAllServiceBitRateElement | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.13 | ||
| Data unit which is counted by the bit rate measurement algorithm for services. When a manager sets the value of this object, the values of the tsMeasurePrefServiceBitRateElement columns in all the rows of the tsMeasurePreferencesServiceTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau. | |||
| OBJECT-TYPE | |||
| BitRateElement | |||
| tsMeasurePrefAllPIDBitRateTau | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.14 | ||
| 'tau' value for Service bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefPIDBitRateTau columns in all the rows of the tsMeasurePreferencesPIDTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsMeasurePrefAllPIDBitRateN | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.15 | ||
| 'N' value for PID bit rate measurement. When a manager sets the value of this object, the values of the tsMeasurePrefPIDBitRateN columns in all the rows of the tsMeasurePreferencesPIDTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau. | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| tsMeasurePrefAllPIDBitRateElement | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.16 | ||
| Data unit which is counted by the bit rate measurement algorithm for PIDs. When a manager sets the value of this object, the values of the tsMeasurePrefPIDBitRateElement columns in all the rows of the tsMeasurePreferencesPIDTable are set to this same value. This also becomes the default value for any new rows created subsequently. See note in description for tsMeasurePrefTSBitRateTau. | |||
| OBJECT-TYPE | |||
| BitRateElement | |||
| tsMeasurePrefExpectedTSID | 1.3.6.1.4.1.2696.3.2.1.5.4.100.1.1.17 | ||
| This object defines the expected Transport Stream ID that is compared with the actual ID to perform the consistency of information check. | |||
| OBJECT-TYPE | |||
| TransportStreamID | |||
| tsMeasurePreferencesServiceTable | 1.3.6.1.4.1.2696.3.2.1.5.4.100.2 | ||
| This table contains configuration information for the tsMeasurements branch of the MIB. Configuration related to individual services is found here. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TsMeasurePreferencesServiceEntry | |||
| tsMeasurePreferencesServiceEntry | 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| TsMeasurePreferencesServiceEntry | |||
| tsMeasurePrefServiceInputNumber | 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.1 | ||
| Transport Stream input to which the preferences apply | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| tsMeasurePrefServiceService | 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.2 | ||
| Service to which the preferences apply. | |||
| OBJECT-TYPE | |||
| ServiceId | |||
| tsMeasurePrefServiceRowStatus | 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.3 | ||
| This is used by the manager to create and delete rows in the table. The agent will automatically create rows for services it finds in the PMT. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| tsMeasurePrefServiceBitRateTau | 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.4 | ||
| 'tau' value for bit rate measurement for this service. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per service tau settings, it shall ignore attempts to change the setting by writing to this object. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsMeasurePrefServiceBitRateN | 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.5 | ||
| 'N' value for rate measurement for this service. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per service 'N' settings, it shall ignore attempts to change the setting by writing to this object. | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| tsMeasurePrefServiceBitRateElement | 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.6 | ||
| Data unit which is counted by the bit rate measurement algorithm for this service. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per service element settings, it shall ignore attempts to change the setting by writing to this object. | |||
| OBJECT-TYPE | |||
| BitRateElement | |||
| tsMeasurePrefServiceBitRateMin | 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.7 | ||
| An error is generated if the Service bit rate is below this value. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsMeasurePrefServiceBitRateMax | 1.3.6.1.4.1.2696.3.2.1.5.4.100.2.1.8 | ||
| An error is generated if the Transport Stream bit rate exceeds this value. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsMeasurePreferencesPIDTable | 1.3.6.1.4.1.2696.3.2.1.5.4.100.3 | ||
| This table contains configuration information for the tsMeasurements branch of the MIB. Configuration related to individual PIDs is found here. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TsMeasurePreferencesPIDEntry | |||
| tsMeasurePreferencesPIDEntry | 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| TsMeasurePreferencesPIDEntry | |||
| tsMeasurePrefPIDInputNumber | 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.1 | ||
| Transport Stream input to which the preferences apply | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| tsMeasurePrefPIDPID | 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.2 | ||
| PID (plus one) to which the preferences apply. | |||
| OBJECT-TYPE | |||
| PIDPlusOne | |||
| tsMeasurePrefPIDRowStatus | 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.3 | ||
| This is used by the manager to create and delete rows in the table. The agent will automatically create rows for PIDs which have a non-zero bit rate. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| tsMeasurePrefPIDBitRateTau | 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.4 | ||
| 'tau' value for bit rate measurement for this PID. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per PID tau settings, it shall ignore attempts to change the setting by writing to this object. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsMeasurePrefPIDBitRateN | 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.5 | ||
| 'N' value for bit rate measurement for this PID. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per PID 'N' settings, it shall ignore attempts to change the setting by writing to this object. | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| tsMeasurePrefPIDBitRateElement | 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.6 | ||
| Data unit which is counted by the bit rate measurement algorithm for this PID. See note in description for tsMeasurePrefTSBitRateTau. If an agent does not support per PID element settings, it shall ignore attempts to change the setting by writing to this object. | |||
| OBJECT-TYPE | |||
| BitRateElement | |||
| tsMeasurePrefPIDBitRateMin | 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.7 | ||
| An error is generated if the PID bit rate is below this value. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsMeasurePrefPIDBitRateMax | 1.3.6.1.4.1.2696.3.2.1.5.4.100.3.1.8 | ||
| An error is generated if the PID bit rate exceeds this value. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsServicePerformance | 1.3.6.1.4.1.2696.3.2.1.5.5 | ||
| OBJECT IDENTIFIER | |||
| tsServicePerformanceTable | 1.3.6.1.4.1.2696.3.2.1.5.5.2 | ||
| This table gives access to the Service Performance measurements and tests | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TsServicePerformanceEntry | |||
| tsServicePerformanceEntry | 1.3.6.1.4.1.2696.3.2.1.5.5.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| TsServicePerformanceEntry | |||
| tsServicePerformanceInputNumber | 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| tsServicePerformanceNumber | 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.2 | ||
| The Service Performance measurement which this row applies to. | |||
| OBJECT-TYPE | |||
| IndexServicePerformance | |||
| tsServicePerformanceState | 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.3 | ||
| This gives the overall pass/fail state of the threshold test on this measurement. The threshold test fails if the value of tsServicePerformanceErrorRatio exceeds the value given in the preferences. | |||
| OBJECT-TYPE | |||
| TestState | |||
| tsServicePerformanceEnable | 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.4 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| tsServicePerformanceCounter | 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.5 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| tsServicePerformanceCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.6 | ||
| Provides the last time at which there was a discontinuity in the tsServicePerformanceCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsServicePerformanceCounterReset | 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.7 | ||
| tsServicePerformanceCounter is reset to zero and tsServicePerformanceCounterDiscontinuity is set to the current time if 'true' is written to this variable. The value read from this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| tsServicePerformanceLatestError | 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.8 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| tsServicePerformanceActiveTime | 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.9 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| tsServicePerformanceMeasurementState | 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.10 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| tsServicePerformanceError | 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.11 | ||
| The calculated xxx_Error parameter as measured at the end of the most recently completed DeltaT period. | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| tsServicePerformanceErrorRatio | 1.3.6.1.4.1.2696.3.2.1.5.5.2.1.12 | ||
| This is the calculated xxx_Error_Ratio as a percentage (e.g. '1.32'). The value is for the most recently completed evaluation time (e.g. 10 minutes). | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsServicePerformancePreferencesTable | 1.3.6.1.4.1.2696.3.2.1.5.5.100 | ||
| Parameters controlling the Service Performance measurements | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TsServicePerformancePreferencesEntry | |||
| tsServicePerformancePreferencesEntry | 1.3.6.1.4.1.2696.3.2.1.5.5.100.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| TsServicePerformancePreferencesEntry | |||
| tsSPPrefInputNumber | 1.3.6.1.4.1.2696.3.2.1.5.5.100.1.1 | ||
| Transport Stream input to which the preferences apply | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| tsSPPrefNumber | 1.3.6.1.4.1.2696.3.2.1.5.5.100.1.2 | ||
| The service performance parameter to which these preferences apply. | |||
| OBJECT-TYPE | |||
| IndexServicePerformance | |||
| tsSPPrefDeltaT | 1.3.6.1.4.1.2696.3.2.1.5.5.100.1.3 | ||
| The defined time interval over which errors are counted | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsSPPrefEvaluationTime | 1.3.6.1.4.1.2696.3.2.1.5.5.100.1.4 | ||
| The period over which the ...Error_Ratio is calculated | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tsSPPrefThreshold | 1.3.6.1.4.1.2696.3.2.1.5.5.100.1.5 | ||
| The threshold value used in calculating the ..._Error_Ratio. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tr101290CableSat | 1.3.6.1.4.1.2696.3.2.1.6 | ||
| OBJECT IDENTIFIER | |||
| sysAvailabilityTable | 1.3.6.1.4.1.2696.3.2.1.6.1 | ||
| System availability measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysAvailabilityEntry | |||
| sysAvailabilityEntry | 1.3.6.1.4.1.2696.3.2.1.6.1.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| SysAvailabilityEntry | |||
| sysAvailabilityInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.1.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| sysAvailabilityTestState | 1.3.6.1.4.1.2696.3.2.1.6.1.1.2 | ||
| A 'fail' is an approximate indication that the system is in a period of unavailable time (UAT). 'fail' is indicated as soon as a trigger period for unavailable time completes. 'pass' is indicated as soon as a trigger period for available time completes. This necessarily differs from the strict definition of UAT because the measuring equipment is unable to look into the future. | |||
| OBJECT-TYPE | |||
| TestState | |||
| sysAvailabilityEnable | 1.3.6.1.4.1.2696.3.2.1.6.1.1.3 | ||
| Determines whether system availability testing is performed and whether the associated traps are generated. | |||
| OBJECT-TYPE | |||
| Enable | |||
| sysAvailabilityCounter | 1.3.6.1.4.1.2696.3.2.1.6.1.1.4 | ||
| Count of the number of times the system has become unavailable | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| sysAvailabilityCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.6.1.1.5 | ||
| Provides the last time at which there was a discontinuity in the sysAvailabilityCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| sysAvailabilityCounterReset | 1.3.6.1.4.1.2696.3.2.1.6.1.1.6 | ||
| sysAvailabilityCounter is reset to zero and sysAvailabilityCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| sysAvailabilityLatestError | 1.3.6.1.4.1.2696.3.2.1.6.1.1.7 | ||
| The timestamp when the system most recently became unavailable. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| sysAvailabilityActiveTime | 1.3.6.1.4.1.2696.3.2.1.6.1.1.8 | ||
| This is a monotonically increasing value in units of seconds that represents the total amount of time for which the instrument has been able to perform the test/measurement. It can be used to calculate the Total Time in the calculation of the availability. | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| sysAvailabilityMeasurementState | 1.3.6.1.4.1.2696.3.2.1.6.1.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| sysAvailabilityUnavailableTime | 1.3.6.1.4.1.2696.3.2.1.6.1.1.10 | ||
| This is a monotonically increasing time in seconds which measures the total Unavailable Time (UAT) since the measuring system was last restarted. | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| sysAvailabilityRatio | 1.3.6.1.4.1.2696.3.2.1.6.1.1.11 | ||
| This is the System Availability ratio as a percentage (e.g. 99.643) measured over the previous 'Total Time' measurement period. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| sysAvailabilityInSETI | 1.3.6.1.4.1.2696.3.2.1.6.1.1.12 | ||
| This object has the value 'true' if and only if the most recently completed Time Interval (TI) was a Severely Errored Time Interval (SETI). | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| linkAvailabilityTable | 1.3.6.1.4.1.2696.3.2.1.6.2 | ||
| Link availability measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LinkAvailabilityEntry | |||
| linkAvailabilityEntry | 1.3.6.1.4.1.2696.3.2.1.6.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| LinkAvailabilityEntry | |||
| linkAvailabilityInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.2.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| linkAvailabilityTestState | 1.3.6.1.4.1.2696.3.2.1.6.2.1.2 | ||
| A 'fail' is an approximate indication that the system is in a period of link unavailable time (LUAT). 'fail' is indicated as soon as a trigger period for link unavailable time completes. 'pass' is indicated as soon as a trigger period for link available time completes. This necessarily differs from the strict definition of LUAT because the measuring equipment is unable to look into the future. | |||
| OBJECT-TYPE | |||
| TestState | |||
| linkAvailabilityEnable | 1.3.6.1.4.1.2696.3.2.1.6.2.1.3 | ||
| Determines whether link availability testing is performed and whether the associated traps are generated. | |||
| OBJECT-TYPE | |||
| Enable | |||
| linkAvailabilityCounter | 1.3.6.1.4.1.2696.3.2.1.6.2.1.4 | ||
| Count of the number of times the link has become unavailable. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| linkAvailabilityCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.6.2.1.5 | ||
| Provides the last time at which there was a discontinuity in the linkAvailabilityCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| linkAvailabilityCounterReset | 1.3.6.1.4.1.2696.3.2.1.6.2.1.6 | ||
| linkAvailabilityCounter is reset to zero and linkAvailabilityCounterDiscontinuity is set to the current time if 'true' is written to this variable. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| linkAvailabilityLatestError | 1.3.6.1.4.1.2696.3.2.1.6.2.1.7 | ||
| The timestamp when the link most recently became unavailable. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| linkAvailabilityActiveTime | 1.3.6.1.4.1.2696.3.2.1.6.2.1.8 | ||
| This is a monotonically increasing value in units of seconds that represents the total amount of time for which the instrument has been able to perform the measurement. It can be used to calculate the Total Time in the calculation of the availability. | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| linkAvailabilityMeasurementState | 1.3.6.1.4.1.2696.3.2.1.6.2.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| linkAvailabilityUnavailableTime | 1.3.6.1.4.1.2696.3.2.1.6.2.1.10 | ||
| This is a monotonically increasing time in seconds which measures the total link unavailable time (LUAT) since the measuring system was last restarted. | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| linkAvailabilityRatio | 1.3.6.1.4.1.2696.3.2.1.6.2.1.11 | ||
| This is the Link Availability ratio as a percentage (e.g. 99.643) measured over the previous 'Total Time' measurement period. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| linkAvailabilityInSUTI | 1.3.6.1.4.1.2696.3.2.1.6.2.1.12 | ||
| This object has the value 'true' if and only if the most recently completed Time Interval (TI) was a Severely Uncorrectable Time Interval (SETI). | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| berRSinServiceTable | 1.3.6.1.4.1.2696.3.2.1.6.3 | ||
| Measurement of BER before RS decoder | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BerRSinServiceEntry | |||
| berRSinServiceEntry | 1.3.6.1.4.1.2696.3.2.1.6.3.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| BerRSinServiceEntry | |||
| berRSinServiceInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.3.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| berRSinServiceTestState | 1.3.6.1.4.1.2696.3.2.1.6.3.1.2 | ||
| This indicates whether the berRSinServiceValue is below the maximum. | |||
| OBJECT-TYPE | |||
| TestState | |||
| berRSinServiceEnable | 1.3.6.1.4.1.2696.3.2.1.6.3.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| berRSinServiceCounter | 1.3.6.1.4.1.2696.3.2.1.6.3.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| berRSinServiceCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.6.3.1.5 | ||
| Provides the last time at which there was a discontinuity in the berRSinServiceCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| berRSinServiceCounterReset | 1.3.6.1.4.1.2696.3.2.1.6.3.1.6 | ||
| berRSinServiceCounter is reset to zero and berRSinServiceCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| berRSinServiceLatestError | 1.3.6.1.4.1.2696.3.2.1.6.3.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| berRSinServiceActiveTime | 1.3.6.1.4.1.2696.3.2.1.6.3.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| berRSinServiceMeasurementState | 1.3.6.1.4.1.2696.3.2.1.6.3.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| berRSinServiceValue | 1.3.6.1.4.1.2696.3.2.1.6.3.1.10 | ||
| This is the current BER as a numeric value, for example 0.0000023 | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| rfIFsignalPowerTable | 1.3.6.1.4.1.2696.3.2.1.6.6 | ||
| RF or IF signal power measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RfIFsignalPowerEntry | |||
| rfIFsignalPowerEntry | 1.3.6.1.4.1.2696.3.2.1.6.6.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| RfIFsignalPowerEntry | |||
| rfIFsignalPowerInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.6.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| rfIFsignalPowerTestState | 1.3.6.1.4.1.2696.3.2.1.6.6.1.2 | ||
| This indicates whether the rfIFsignalPowerValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| rfIFsignalPowerEnable | 1.3.6.1.4.1.2696.3.2.1.6.6.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| rfIFsignalPowerCounter | 1.3.6.1.4.1.2696.3.2.1.6.6.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| rfIFsignalPowerCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.6.6.1.5 | ||
| Provides the last time at which there was a discontinuity in the rfIFsignalPowerCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| rfIFsignalPowerCounterReset | 1.3.6.1.4.1.2696.3.2.1.6.6.1.6 | ||
| rfIFsignalPowerCounter is reset to zero and rfIFsignalPowerCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| rfIFsignalPowerLatestError | 1.3.6.1.4.1.2696.3.2.1.6.6.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| rfIFsignalPowerActiveTime | 1.3.6.1.4.1.2696.3.2.1.6.6.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| rfIFsignalPowerMeasurementState | 1.3.6.1.4.1.2696.3.2.1.6.6.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| rfIFsignalPowerValue | 1.3.6.1.4.1.2696.3.2.1.6.6.1.10 | ||
| The current RF power expressed in dBm, which references 0 dBm as the power of 1 mW. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| noisePowerTable | 1.3.6.1.4.1.2696.3.2.1.6.7 | ||
| Noise power measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| NoisePowerEntry | |||
| noisePowerEntry | 1.3.6.1.4.1.2696.3.2.1.6.7.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| NoisePowerEntry | |||
| noisePowerInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.7.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| noisePowerTestState | 1.3.6.1.4.1.2696.3.2.1.6.7.1.2 | ||
| This indicates whether the noisePowerValue is currently below the maximum limit. | |||
| OBJECT-TYPE | |||
| TestState | |||
| noisePowerEnable | 1.3.6.1.4.1.2696.3.2.1.6.7.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| noisePowerCounter | 1.3.6.1.4.1.2696.3.2.1.6.7.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| noisePowerCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.6.7.1.5 | ||
| Provides the last time at which there was a discontinuity in the noisePowerCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| noisePowerCounterReset | 1.3.6.1.4.1.2696.3.2.1.6.7.1.6 | ||
| noisePowerCounter is reset to zero and noisePowerCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| noisePowerLatestError | 1.3.6.1.4.1.2696.3.2.1.6.7.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| noisePowerActiveTime | 1.3.6.1.4.1.2696.3.2.1.6.7.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| noisePowerMeasurementState | 1.3.6.1.4.1.2696.3.2.1.6.7.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| noisePowerValue | 1.3.6.1.4.1.2696.3.2.1.6.7.1.10 | ||
| The current RF noise power expressed in dBm, which references 0 dBm as the power of 1 mW. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| iqAnalysisCS | 1.3.6.1.4.1.2696.3.2.1.6.9 | ||
| OBJECT IDENTIFIER | |||
| merCSTable | 1.3.6.1.4.1.2696.3.2.1.6.9.2 | ||
| Modulation Error Ratio (MER) | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MerCSEntry | |||
| merCSEntry | 1.3.6.1.4.1.2696.3.2.1.6.9.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| MerCSEntry | |||
| merCSInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| merCSTestState | 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.2 | ||
| This indicates whether the merCSValue is currently below the maximum limit. | |||
| OBJECT-TYPE | |||
| TestState | |||
| merCSEnable | 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| merCSCounter | 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| merCSCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.5 | ||
| Provides the last time at which there was a discontinuity in the merCSCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| merCSCounterReset | 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.6 | ||
| merCSCounter is reset to zero and merCSCounterDiscontinuity is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| merCSLatestError | 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| merCSActiveTime | 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| merCSMeasurementState | 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| merCSValue | 1.3.6.1.4.1.2696.3.2.1.6.9.2.1.10 | ||
| The Modulation Error Ratio expressed in dB | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| steCS | 1.3.6.1.4.1.2696.3.2.1.6.9.3 | ||
| OBJECT IDENTIFIER | |||
| steMeanCSTable | 1.3.6.1.4.1.2696.3.2.1.6.9.3.1 | ||
| System Target Error (mean value) | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SteMeanCSEntry | |||
| steMeanCSEntry | 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| SteMeanCSEntry | |||
| steMeanCSInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| steMeanCSTestState | 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.2 | ||
| This indicates whether the steMeanCSValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| steMeanCSEnable | 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| steMeanCSCounter | 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| steMeanCSCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| steMeanCSCounterReset | 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| steMeanCSLatestError | 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| steMeanCSActiveTime | 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| steMeanCSMeasurementState | 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| steMeanCSValue | 1.3.6.1.4.1.2696.3.2.1.6.9.3.1.1.10 | ||
| The current System Target Error Mean as a numeric value | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| steDeviationCSTable | 1.3.6.1.4.1.2696.3.2.1.6.9.3.2 | ||
| System Target Error (deviation value) | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SteDeviationCSEntry | |||
| steDeviationCSEntry | 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| SteDeviationCSEntry | |||
| steDeviationCSInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| steDeviationCSTestState | 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.2 | ||
| This indicates whether the steDeviationCSValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| steDeviationCSEnable | 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| steDeviationCSCounter | 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| steDeviationCSCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| steDeviationCSCounterReset | 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| steDeviationCSLatestError | 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| steDeviationCSActiveTime | 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| steDeviationCSMeasurementState | 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| steDeviationCSValue | 1.3.6.1.4.1.2696.3.2.1.6.9.3.2.1.10 | ||
| The current System Target Error Deviation as a numeric value | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| csCSTable | 1.3.6.1.4.1.2696.3.2.1.6.9.4 | ||
| Carrier suppression measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CsCSEntry | |||
| csCSEntry | 1.3.6.1.4.1.2696.3.2.1.6.9.4.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| CsCSEntry | |||
| csCSInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| csCSTestState | 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.2 | ||
| This indicates whether the csCSValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| csCSEnable | 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| csCSCounter | 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| csCSCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| csCSCounterReset | 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| csCSLatestError | 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| csCSActiveTime | 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| csCSMeasurementState | 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| csCSValue | 1.3.6.1.4.1.2696.3.2.1.6.9.4.1.10 | ||
| The current Carrier Suppression value in dB. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| aiCSTable | 1.3.6.1.4.1.2696.3.2.1.6.9.5 | ||
| Amplitude Imbalance (AI) measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AiCSEntry | |||
| aiCSEntry | 1.3.6.1.4.1.2696.3.2.1.6.9.5.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| AiCSEntry | |||
| aiCSInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| aiCSTestState | 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.2 | ||
| This indicates whether the aiCSValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| aiCSEnable | 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| aiCSCounter | 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| aiCSCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| aiCSCounterReset | 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| aiCSLatestError | 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| aiCSActiveTime | 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| aiCSMeasurementState | 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| aiCSValue | 1.3.6.1.4.1.2696.3.2.1.6.9.5.1.10 | ||
| The current Amplitude Imbalance as a percentage | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| qeCSTable | 1.3.6.1.4.1.2696.3.2.1.6.9.6 | ||
| Quadrature Error (QE) measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| QeCSEntry | |||
| qeCSEntry | 1.3.6.1.4.1.2696.3.2.1.6.9.6.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| QeCSEntry | |||
| qeCSInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| qeCSTestState | 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.2 | ||
| This indicates whether the qeCSValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| qeCSEnable | 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| qeCSCounter | 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| qeCSCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| qeCSCounterReset | 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| qeCSLatestError | 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| qeCSActiveTime | 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| qeCSMeasurementState | 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| qeCSValue | 1.3.6.1.4.1.2696.3.2.1.6.9.6.1.10 | ||
| The current Quadrature Error value in degrees. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| rteCSTable | 1.3.6.1.4.1.2696.3.2.1.6.9.7 | ||
| Residual Target Error (RTE) measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RteCSEntry | |||
| rteCSEntry | 1.3.6.1.4.1.2696.3.2.1.6.9.7.1 | ||
| Row description | |||
| OBJECT-TYPE | |||
| RteCSEntry | |||
| rteCSInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| rteCSTestState | 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.2 | ||
| This indicates whether the rteCSValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| rteCSEnable | 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| rteCSCounter | 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| rteCSCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| rteCSCounterReset | 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| rteCSLatestError | 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| rteCSActiveTime | 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| rteCSMeasurementState | 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| rteCSValue | 1.3.6.1.4.1.2696.3.2.1.6.9.7.1.10 | ||
| The current Residual Target Error value as a numeric value. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| ciCSTable | 1.3.6.1.4.1.2696.3.2.1.6.9.8 | ||
| Coherent Interferer measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CiCSEntry | |||
| ciCSEntry | 1.3.6.1.4.1.2696.3.2.1.6.9.8.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| CiCSEntry | |||
| ciCSInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| ciCSTestState | 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.2 | ||
| This indicates whether the ciCSValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| ciCSEnable | 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| ciCSCounter | 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| ciCSCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| ciCSCounterReset | 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| ciCSLatestError | 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| ciCSActiveTime | 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| ciCSMeasurementState | 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| ciCSValue | 1.3.6.1.4.1.2696.3.2.1.6.9.8.1.10 | ||
| The current Coherent Interferer value in dB. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| pjCSTable | 1.3.6.1.4.1.2696.3.2.1.6.9.9 | ||
| Phase Jitter (PJ) measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PjCSEntry | |||
| pjCSEntry | 1.3.6.1.4.1.2696.3.2.1.6.9.9.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| PjCSEntry | |||
| pjCSInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| pjCSTestState | 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.2 | ||
| This indicates whether the pjCSValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| pjCSEnable | 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| pjCSCounter | 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pjCSCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| pjCSCounterReset | 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| pjCSLatestError | 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| pjCSActiveTime | 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| pjCSMeasurementState | 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| pjCSValue | 1.3.6.1.4.1.2696.3.2.1.6.9.9.1.10 | ||
| The current Phase Jitter value in degrees. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| snrCSTable | 1.3.6.1.4.1.2696.3.2.1.6.9.10 | ||
| Signal-to-Noise Ratio (SNR) | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnrCSEntry | |||
| snrCSEntry | 1.3.6.1.4.1.2696.3.2.1.6.9.10.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| SnrCSEntry | |||
| snrCSInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| snrCSTestState | 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.2 | ||
| This indicates whether the snrCSValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| snrCSEnable | 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| snrCSCounter | 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| snrCSCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| snrCSCounterReset | 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| snrCSLatestError | 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| snrCSActiveTime | 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| snrCSMeasurementState | 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| snrCSValue | 1.3.6.1.4.1.2696.3.2.1.6.9.10.1.10 | ||
| The current Signal-to-Noise value in dB. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPreferencesTable | 1.3.6.1.4.1.2696.3.2.1.6.100 | ||
| Table containing per input configuration information for cable and satellite common measurements. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CableSatPreferencesEntry | |||
| cableSatPreferencesEntry | 1.3.6.1.4.1.2696.3.2.1.6.100.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| CableSatPreferencesEntry | |||
| cableSatPrefInputNumber | 1.3.6.1.4.1.2696.3.2.1.6.100.1.1 | ||
| Transport Stream input to which the preferences apply | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| cableSatPrefCentreFrequency | 1.3.6.1.4.1.2696.3.2.1.6.100.1.2 | ||
| This is the centre frequency to which the measuring equipment is tuned for making cable and satellite measurements. This frequency is the actual input frequency to the measuring equipment, which may be at an intermediate frequency (IF) rather than the final RF. This setting affects the objects in the 'tr101290Cable' and 'tr101290Satellite' branches of the MIB as well as the 'tr101290CableSat' branch. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefModulation | 1.3.6.1.4.1.2696.3.2.1.6.100.1.3 | ||
| This is the modulation which the measuring equipment expects to see and against which it makes modulation measurements. This applies to cable and satellite measurements. This setting affects the objects in the 'tr101290Cable' and 'tr101290Satellite' branches of the MIB as well as the 'tr101290CableSat' branch. | |||
| OBJECT-TYPE | |||
| Modulation | |||
| cableSatPrefSysAvailUATMode | 1.3.6.1.4.1.2696.3.2.1.6.100.1.4 | ||
| Determines whether the 'N consecutive' or 'rolling window' mode of determining the start of a period of Unavailable Time (UAT) is used. If the 'N consecutive' mode is selected, the 'M' and 'T' preference parameters are ignored. Likewise, if the 'rolling window' mode is selected, the 'N' preference parameter is ignored. | |||
| OBJECT-TYPE | |||
| UATMode | |||
| cableSatPrefSysAvailN | 1.3.6.1.4.1.2696.3.2.1.6.100.1.5 | ||
| The N value used to identify the start and end of a period of unavailable time (UAT). | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| cableSatPrefSysAvailT | 1.3.6.1.4.1.2696.3.2.1.6.100.1.6 | ||
| The T value used to identify the start and end of a period of unavailable time (UAT). | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefSysAvailM | 1.3.6.1.4.1.2696.3.2.1.6.100.1.7 | ||
| The M value used to identify the start and end of a period of unavailable time (UAT). | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| cableSatPrefSysAvailTI | 1.3.6.1.4.1.2696.3.2.1.6.100.1.8 | ||
| Each Time Interval of this length is assessed as to whether it is a Severely Errored Time Interval. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefSysAvailEBPerCent | 1.3.6.1.4.1.2696.3.2.1.6.100.1.9 | ||
| If more than this percentage of blocks within a Time Interval is an Errored Block, the Time Interval is a Severely Errored Time Interval (SETI). Example values are: '1.53', '10', '0.33'. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefSysAvailTotalTime | 1.3.6.1.4.1.2696.3.2.1.6.100.1.10 | ||
| The Total Time over which the System Availability is calculated. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefLinkAvailUATMode | 1.3.6.1.4.1.2696.3.2.1.6.100.1.11 | ||
| Determines whether the 'N consecutive' or 'rolling window' mode of determining the start of a period of Link Unavailable Time (LUAT) is used. If the 'N consecutive' mode is selected, the 'M' and 'T' preference parameters are ignored. Likewise, if the 'rolling window' mode is selected, the 'N' preference parameter is ignored. | |||
| OBJECT-TYPE | |||
| UATMode | |||
| cableSatPrefLinkAvailN | 1.3.6.1.4.1.2696.3.2.1.6.100.1.12 | ||
| The N value used to identify the start and end of a period of Link Unavailable Time (LUAT). | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| cableSatPrefLinkAvailT | 1.3.6.1.4.1.2696.3.2.1.6.100.1.13 | ||
| The T value used to identify the start and end of a period of Link Unavailable Time (LUAT). | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefLinkAvailM | 1.3.6.1.4.1.2696.3.2.1.6.100.1.14 | ||
| The M value used to identify the start and end of a period of Link Unavailable Time (LUAT). | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| cableSatPrefLinkAvailTI | 1.3.6.1.4.1.2696.3.2.1.6.100.1.15 | ||
| Each Time Interval of this length is assessed as to whether it is a Severely Uncorrectable Time Interval (SUTI). | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefLinkAvailUPPerCent | 1.3.6.1.4.1.2696.3.2.1.6.100.1.16 | ||
| If more than this percentage of packets within a Time Interval is an Uncorrectable Packet (UP), the Time Interval is a Severely Uncorrectable Time Interval (SUTI). Example values are: '1.53', '10', '0.33'. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefLinkAvailTotalTime | 1.3.6.1.4.1.2696.3.2.1.6.100.1.17 | ||
| The Total Time over which the Link Availability is calculated. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefBERMax | 1.3.6.1.4.1.2696.3.2.1.6.100.1.18 | ||
| If the berRSinServiceValue exceeds this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefSignalPowerMin | 1.3.6.1.4.1.2696.3.2.1.6.100.1.19 | ||
| If the power measured by rfIFsignalPowerValue is less than this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefSignalPowerMax | 1.3.6.1.4.1.2696.3.2.1.6.100.1.20 | ||
| If the power measured by rfIFsignalPowerValue is greater than this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefNoisePowerMax | 1.3.6.1.4.1.2696.3.2.1.6.100.1.21 | ||
| If the noise power measured by noisePowerValue exceeds this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefMerCSMin | 1.3.6.1.4.1.2696.3.2.1.6.100.1.22 | ||
| If the merCSValue is less than this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefSteMeanCSMax | 1.3.6.1.4.1.2696.3.2.1.6.100.1.23 | ||
| If the steMeanCSValue exceeds this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefSteDeviationCSMax | 1.3.6.1.4.1.2696.3.2.1.6.100.1.24 | ||
| If the steDeviationCSValue exceeds this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefCsCSMin | 1.3.6.1.4.1.2696.3.2.1.6.100.1.25 | ||
| If the csCSValue is less than this value, the associated test fails | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefAiCSMax | 1.3.6.1.4.1.2696.3.2.1.6.100.1.26 | ||
| If aiCSValue exceeds this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefQeCSMax | 1.3.6.1.4.1.2696.3.2.1.6.100.1.27 | ||
| If qeCSValue exceeds this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefRteCSMax | 1.3.6.1.4.1.2696.3.2.1.6.100.1.28 | ||
| If rteCSValue exceeds this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefCiCSMin | 1.3.6.1.4.1.2696.3.2.1.6.100.1.29 | ||
| If ciCSValue is less than this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefPjCSMax | 1.3.6.1.4.1.2696.3.2.1.6.100.1.30 | ||
| If pjCSValue exceeds this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cableSatPrefSnrCSMin | 1.3.6.1.4.1.2696.3.2.1.6.100.1.31 | ||
| If snrCSValue is less than this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tr101290Cable | 1.3.6.1.4.1.2696.3.2.1.7 | ||
| OBJECT IDENTIFIER | |||
| noiseMarginTable | 1.3.6.1.4.1.2696.3.2.1.7.1 | ||
| Noise margin measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| NoiseMarginEntry | |||
| noiseMarginEntry | 1.3.6.1.4.1.2696.3.2.1.7.1.1 | ||
| Row description | |||
| OBJECT-TYPE | |||
| NoiseMarginEntry | |||
| noiseMarginInputNumber | 1.3.6.1.4.1.2696.3.2.1.7.1.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| noiseMarginTestState | 1.3.6.1.4.1.2696.3.2.1.7.1.1.2 | ||
| This indicates whether the noiseMarginValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| noiseMarginEnable | 1.3.6.1.4.1.2696.3.2.1.7.1.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| noiseMarginCounter | 1.3.6.1.4.1.2696.3.2.1.7.1.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| noiseMarginCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.7.1.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| noiseMarginCounterReset | 1.3.6.1.4.1.2696.3.2.1.7.1.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| noiseMarginLatestError | 1.3.6.1.4.1.2696.3.2.1.7.1.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| noiseMarginActiveTime | 1.3.6.1.4.1.2696.3.2.1.7.1.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| noiseMarginMeasurementState | 1.3.6.1.4.1.2696.3.2.1.7.1.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| noiseMarginValue | 1.3.6.1.4.1.2696.3.2.1.7.1.1.10 | ||
| The current Noise Margin value in dB. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| estNoiseMarginTable | 1.3.6.1.4.1.2696.3.2.1.7.2 | ||
| Estimated noise margin measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| EstNoiseMarginEntry | |||
| estNoiseMarginEntry | 1.3.6.1.4.1.2696.3.2.1.7.2.1 | ||
| Row description | |||
| OBJECT-TYPE | |||
| EstNoiseMarginEntry | |||
| estNoiseMarginInputNumber | 1.3.6.1.4.1.2696.3.2.1.7.2.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| estNoiseMarginTestState | 1.3.6.1.4.1.2696.3.2.1.7.2.1.2 | ||
| This indicates whether the estNoiseMarginValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| estNoiseMarginEnable | 1.3.6.1.4.1.2696.3.2.1.7.2.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| estNoiseMarginCounter | 1.3.6.1.4.1.2696.3.2.1.7.2.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| estNoiseMarginCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.7.2.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| estNoiseMarginCounterReset | 1.3.6.1.4.1.2696.3.2.1.7.2.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| estNoiseMarginLatestError | 1.3.6.1.4.1.2696.3.2.1.7.2.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| estNoiseMarginActiveTime | 1.3.6.1.4.1.2696.3.2.1.7.2.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| estNoiseMarginMeasurementState | 1.3.6.1.4.1.2696.3.2.1.7.2.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| estNoiseMarginValue | 1.3.6.1.4.1.2696.3.2.1.7.2.1.10 | ||
| The current Estimated Noise Margin value in dB. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| signQualMarTTable | 1.3.6.1.4.1.2696.3.2.1.7.3 | ||
| Signal quality margin test | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SignQualMarTEntry | |||
| signQualMarTEntry | 1.3.6.1.4.1.2696.3.2.1.7.3.1 | ||
| Row description | |||
| OBJECT-TYPE | |||
| SignQualMarTEntry | |||
| signQualMarTInputNumber | 1.3.6.1.4.1.2696.3.2.1.7.3.1.1 | ||
| Transport Stream on which the test is done | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| signQualMarTTestState | 1.3.6.1.4.1.2696.3.2.1.7.3.1.2 | ||
| This indicates an error if the percentage of IQ points outside the threshold box exceeds cablePrefSignQualPercentMax. | |||
| OBJECT-TYPE | |||
| TestState | |||
| signQualMarTEnable | 1.3.6.1.4.1.2696.3.2.1.7.3.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| signQualMarTCounter | 1.3.6.1.4.1.2696.3.2.1.7.3.1.4 | ||
| Count of the number of times an error has occurred. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| signQualMarTCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.7.3.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| signQualMarTCounterReset | 1.3.6.1.4.1.2696.3.2.1.7.3.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| signQualMarTLatestError | 1.3.6.1.4.1.2696.3.2.1.7.3.1.7 | ||
| The timestamp at the most recent occurrence of an error. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| signQualMarTActiveTime | 1.3.6.1.4.1.2696.3.2.1.7.3.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| eNDCTable | 1.3.6.1.4.1.2696.3.2.1.7.4 | ||
| Equivalent Noise Degradation (END) measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ENDCEntry | |||
| eNDCEntry | 1.3.6.1.4.1.2696.3.2.1.7.4.1 | ||
| Row description | |||
| OBJECT-TYPE | |||
| ENDCEntry | |||
| eNDCInputNumber | 1.3.6.1.4.1.2696.3.2.1.7.4.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| eNDCTestState | 1.3.6.1.4.1.2696.3.2.1.7.4.1.2 | ||
| This indicates an error when the eNDCValue exceeds the threshold. | |||
| OBJECT-TYPE | |||
| TestState | |||
| eNDCEnable | 1.3.6.1.4.1.2696.3.2.1.7.4.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| eNDCCounter | 1.3.6.1.4.1.2696.3.2.1.7.4.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| eNDCCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.7.4.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| eNDCCounterReset | 1.3.6.1.4.1.2696.3.2.1.7.4.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| eNDCLatestError | 1.3.6.1.4.1.2696.3.2.1.7.4.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| eNDCActiveTime | 1.3.6.1.4.1.2696.3.2.1.7.4.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| eNDCMeasurementState | 1.3.6.1.4.1.2696.3.2.1.7.4.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| eNDCValue | 1.3.6.1.4.1.2696.3.2.1.7.4.1.10 | ||
| The current Equivalent Noise Degradation value in dB. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| outBandEmissTable | 1.3.6.1.4.1.2696.3.2.1.7.5 | ||
| Out of band emissions test | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OutBandEmissEntry | |||
| outBandEmissEntry | 1.3.6.1.4.1.2696.3.2.1.7.5.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| OutBandEmissEntry | |||
| outBandEmissInputNumber | 1.3.6.1.4.1.2696.3.2.1.7.5.1.1 | ||
| Transport Stream on which the test is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| outBandEmissTestState | 1.3.6.1.4.1.2696.3.2.1.7.5.1.2 | ||
| This indicates whether the spectrum is within the spectrum mask. Note that the spectrum mask must be provided to the instrument by means outside the scope of this MIB. | |||
| OBJECT-TYPE | |||
| TestState | |||
| outBandEmissEnable | 1.3.6.1.4.1.2696.3.2.1.7.5.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| outBandEmissCounter | 1.3.6.1.4.1.2696.3.2.1.7.5.1.4 | ||
| Count of the number of times an error has occurred for this test. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| outBandEmissCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.7.5.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| outBandEmissCounterReset | 1.3.6.1.4.1.2696.3.2.1.7.5.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| outBandEmissLatestError | 1.3.6.1.4.1.2696.3.2.1.7.5.1.7 | ||
| The timestamp at the most recent occurrence of an error on this test. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| outBandEmissActiveTime | 1.3.6.1.4.1.2696.3.2.1.7.5.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| cablePreferencesTable | 1.3.6.1.4.1.2696.3.2.1.7.100 | ||
| Table containing per input preferences for cable measurements. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CablePreferencesEntry | |||
| cablePreferencesEntry | 1.3.6.1.4.1.2696.3.2.1.7.100.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| CablePreferencesEntry | |||
| cablePrefInputNumber | 1.3.6.1.4.1.2696.3.2.1.7.100.1.1 | ||
| Transport Stream input to which the preferences apply | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| cablePrefNoiseMarginMin | 1.3.6.1.4.1.2696.3.2.1.7.100.1.2 | ||
| If the measured noiseMarginValue is less than this value the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cablePrefEstNoiseMarginMin | 1.3.6.1.4.1.2696.3.2.1.7.100.1.3 | ||
| If the measured estNoiseMarginValue is less than this value the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cablePrefSignQualBoxSize | 1.3.6.1.4.1.2696.3.2.1.7.100.1.4 | ||
| This object determines the size of the quality threshold box for the signal quality margin test. The quality threshold box is assumed to be square. The value is the ratio of the length of one side of a threshold box to the length of one side of the IQ decision boundary box. An example value is '0.5'. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cablePrefSignQualPercentMax | 1.3.6.1.4.1.2696.3.2.1.7.100.1.5 | ||
| This object sets the limit on how many constellation points may fall outside the threshold box before the signal quality margin test fails. The value is expressed as a percentage, for example '7.5'. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| cablePrefENDBER | 1.3.6.1.4.1.2696.3.2.1.7.100.1.6 | ||
| BER value which is to be used for the END measurement. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cablePrefENDCtoNSpecified | 1.3.6.1.4.1.2696.3.2.1.7.100.1.7 | ||
| This determines whether cablePrefENDIdeal is expressed as a C/N ratio (value is true) or an Eb/No ratio (value is false). | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| cablePrefENDIdeal | 1.3.6.1.4.1.2696.3.2.1.7.100.1.8 | ||
| This is the 'ideal' value of C/N or Eb/No for the given BER. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| cablePrefENDMax | 1.3.6.1.4.1.2696.3.2.1.7.100.1.9 | ||
| If the measured END exceeds this value the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tr101290Satellite | 1.3.6.1.4.1.2696.3.2.1.8 | ||
| OBJECT IDENTIFIER | |||
| berViterbiSTable | 1.3.6.1.4.1.2696.3.2.1.8.1 | ||
| BER before Viterbi decoding measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BerViterbiSEntry | |||
| berViterbiSEntry | 1.3.6.1.4.1.2696.3.2.1.8.1.1 | ||
| Row description | |||
| OBJECT-TYPE | |||
| BerViterbiSEntry | |||
| berViterbiSInputNumber | 1.3.6.1.4.1.2696.3.2.1.8.1.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| berViterbiSTestState | 1.3.6.1.4.1.2696.3.2.1.8.1.1.2 | ||
| This test fails if either berViterbiSIValue or berViterbiSQValue exceeds the threshold set by satellitePrefBERMax. | |||
| OBJECT-TYPE | |||
| TestState | |||
| berViterbiSEnable | 1.3.6.1.4.1.2696.3.2.1.8.1.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| berViterbiSCounter | 1.3.6.1.4.1.2696.3.2.1.8.1.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| berViterbiSCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.8.1.1.5 | ||
| Provides the last time at which there was a discontinuity in the berViterbiSCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| berViterbiSCounterReset | 1.3.6.1.4.1.2696.3.2.1.8.1.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| berViterbiSLatestError | 1.3.6.1.4.1.2696.3.2.1.8.1.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| berViterbiSActiveTime | 1.3.6.1.4.1.2696.3.2.1.8.1.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| berViterbiSMeasurementState | 1.3.6.1.4.1.2696.3.2.1.8.1.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| berViterbiSIValue | 1.3.6.1.4.1.2696.3.2.1.8.1.1.10 | ||
| This is the pre-Viterbi I path BER value, for example 0.0000023 | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| berViterbiSQValue | 1.3.6.1.4.1.2696.3.2.1.8.1.1.11 | ||
| This is the pre-Viterbi Q path BER value, for example 0.0000023 | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| berViterbiSMeasurementMethod | 1.3.6.1.4.1.2696.3.2.1.8.1.1.12 | ||
| This indicates whether the measurement was made separately for the I and Q parts of the signal or by a measurement of I and Q combined. | |||
| OBJECT-TYPE | |||
| BERMeasurementMethod | |||
| ifSpectrumTable | 1.3.6.1.4.1.2696.3.2.1.8.2 | ||
| IF spectrum test | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| IfSpectrumEntry | |||
| ifSpectrumEntry | 1.3.6.1.4.1.2696.3.2.1.8.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| IfSpectrumEntry | |||
| ifSpectrumInputNumber | 1.3.6.1.4.1.2696.3.2.1.8.2.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| ifSpectrumTestState | 1.3.6.1.4.1.2696.3.2.1.8.2.1.2 | ||
| This indicates whether the spectrum conforms to the template. Note that the spectrum mask must be provided to the instrument by means outside the scope of this MIB. The group delay is not tested. | |||
| OBJECT-TYPE | |||
| TestState | |||
| ifSpectrumEnable | 1.3.6.1.4.1.2696.3.2.1.8.2.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| ifSpectrumCounter | 1.3.6.1.4.1.2696.3.2.1.8.2.1.4 | ||
| Count of the number of times an error has occurred for this test. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| ifSpectrumCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.8.2.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| ifSpectrumCounterReset | 1.3.6.1.4.1.2696.3.2.1.8.2.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| ifSpectrumLatestError | 1.3.6.1.4.1.2696.3.2.1.8.2.1.7 | ||
| The timestamp at the most recent occurrence of an error on this test. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| ifSpectrumActiveTime | 1.3.6.1.4.1.2696.3.2.1.8.2.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| satellitePreferencesTable | 1.3.6.1.4.1.2696.3.2.1.8.100 | ||
| Table of satellite specific measurement preferences. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SatellitePreferencesEntry | |||
| satellitePreferencesEntry | 1.3.6.1.4.1.2696.3.2.1.8.100.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| SatellitePreferencesEntry | |||
| satellitePrefInputNumber | 1.3.6.1.4.1.2696.3.2.1.8.100.1.1 | ||
| Transport Stream input to which the preferences apply | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| satellitePrefBERMax | 1.3.6.1.4.1.2696.3.2.1.8.100.1.2 | ||
| This defines the upper limit on the BER before Viterbi measurement | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tr101290Terrestrial | 1.3.6.1.4.1.2696.3.2.1.9 | ||
| OBJECT IDENTIFIER | |||
| rfTerr | 1.3.6.1.4.1.2696.3.2.1.9.1 | ||
| OBJECT IDENTIFIER | |||
| rfAccuracyTable | 1.3.6.1.4.1.2696.3.2.1.9.1.1 | ||
| RF frequency accuracy (Precision) | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RfAccuracyEntry | |||
| rfAccuracyEntry | 1.3.6.1.4.1.2696.3.2.1.9.1.1.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| RfAccuracyEntry | |||
| rfAccuracyInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.1 | ||
| RF input on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| rfAccuracyTestState | 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.2 | ||
| This indicates whether the rfAccuracyValue is within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| rfAccuracyEnable | 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| rfAccuracyCounter | 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| rfAccuracyCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| rfAccuracyCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| rfAccuracyLatestError | 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| rfAccuracyActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| rfAccuracyMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.9 | ||
| Indicates the validity of the measurement | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| rfAccuracyValue | 1.3.6.1.4.1.2696.3.2.1.9.1.1.1.10 | ||
| This is the RF carrier frequency in Hz. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| rfChannelWidthTable | 1.3.6.1.4.1.2696.3.2.1.9.1.2 | ||
| RF channel width (Sampling Frequency Accuracy) | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RfChannelWidthEntry | |||
| rfChannelWidthEntry | 1.3.6.1.4.1.2696.3.2.1.9.1.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| RfChannelWidthEntry | |||
| rfChannelWidthInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| rfChannelWidthTestState | 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.2 | ||
| This indicates whether the rfChannelWidthValue is within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| rfChannelWidthEnable | 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| rfChannelWidthCounter | 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| rfChannelWidthCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| rfChannelWidthCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| rfChannelWidthLatestError | 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| rfChannelWidthActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| rfChannelWidthMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| rfChannelWidthValue | 1.3.6.1.4.1.2696.3.2.1.9.1.2.1.10 | ||
| This is the RF channel width in Hz. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| symbolLengthTable | 1.3.6.1.4.1.2696.3.2.1.9.1.3 | ||
| Symbol Length measurement at RF (Guard Interval verification) | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SymbolLengthEntry | |||
| symbolLengthEntry | 1.3.6.1.4.1.2696.3.2.1.9.1.3.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| SymbolLengthEntry | |||
| symbolLengthInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| symbolLengthTestState | 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.2 | ||
| This indicates whether the symbolLengthValue is within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| symbolLengthEnable | 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| symbolLengthCounter | 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| symbolLengthCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| symbolLengthCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| symbolLengthLatestError | 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| symbolLengthActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| symbolLengthMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| symbolLengthValue | 1.3.6.1.4.1.2696.3.2.1.9.1.3.1.10 | ||
| This is the symbol length in microseconds. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| rfIfPowerTable | 1.3.6.1.4.1.2696.3.2.1.9.5 | ||
| RF/IF signal power | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RfIfPowerEntry | |||
| rfIfPowerEntry | 1.3.6.1.4.1.2696.3.2.1.9.5.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| RfIfPowerEntry | |||
| rfIfPowerInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.5.1.1 | ||
| RF input on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| rfIfPowerTestState | 1.3.6.1.4.1.2696.3.2.1.9.5.1.2 | ||
| This indicates whether the rfIfPowerValue is within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| rfIfPowerEnable | 1.3.6.1.4.1.2696.3.2.1.9.5.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| rfIfPowerCounter | 1.3.6.1.4.1.2696.3.2.1.9.5.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| rfIfPowerCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.5.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| rfIfPowerCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.5.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| rfIfPowerLatestError | 1.3.6.1.4.1.2696.3.2.1.9.5.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| rfIfPowerActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.5.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| rfIfPowerMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.5.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| rfIfPowerValue | 1.3.6.1.4.1.2696.3.2.1.9.5.1.10 | ||
| The current RF power expressed in dBm, which references 0 dBm as the power of 1 mW. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| rfIfSpectrumTable | 1.3.6.1.4.1.2696.3.2.1.9.7 | ||
| RF and IF spectrum mask test | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RfIfSpectrumEntry | |||
| rfIfSpectrumEntry | 1.3.6.1.4.1.2696.3.2.1.9.7.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| RfIfSpectrumEntry | |||
| rfIfSpectrumInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.7.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| rfIfSpectrumTestState | 1.3.6.1.4.1.2696.3.2.1.9.7.1.2 | ||
| This indicates whether the signal conforms to the spectrum mask | |||
| OBJECT-TYPE | |||
| TestState | |||
| rfIfSpectrumEnable | 1.3.6.1.4.1.2696.3.2.1.9.7.1.3 | ||
| Determines whether the spectrum mask test and the associated trap are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| rfIfSpectrumCounter | 1.3.6.1.4.1.2696.3.2.1.9.7.1.4 | ||
| Count of the number of times an error has occurred. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| rfIfSpectrumCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.7.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| rfIfSpectrumCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.7.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| rfIfSpectrumLatestError | 1.3.6.1.4.1.2696.3.2.1.9.7.1.7 | ||
| The timestamp at the most recent occurrence of an error. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| rfIfSpectrumActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.7.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| eNDT | 1.3.6.1.4.1.2696.3.2.1.9.9 | ||
| OBJECT IDENTIFIER | |||
| eNDTTable | 1.3.6.1.4.1.2696.3.2.1.9.9.1 | ||
| Equivalent Noise Degradation measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If the transmission is not hierarchical, this table contains the measurement for the whole stream. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ENDTEntry | |||
| eNDTEntry | 1.3.6.1.4.1.2696.3.2.1.9.9.1.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| ENDTEntry | |||
| eNDTInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| eNDTTestState | 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.2 | ||
| This indicates whether eNDTValue is within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| eNDTEnable | 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| eNDTCounter | 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| eNDTCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| eNDTCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| eNDTLatestError | 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| eNDTActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| eNDTMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| eNDTValue | 1.3.6.1.4.1.2696.3.2.1.9.9.1.1.10 | ||
| The current Equivalent Noise Degradation expressed in dB. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| eNFTTable | 1.3.6.1.4.1.2696.3.2.1.9.9.2 | ||
| Equivalent Noise Floor measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If the transmission is not hierarchical, this table contains the measurement for the whole stream. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ENFTEntry | |||
| eNFTEntry | 1.3.6.1.4.1.2696.3.2.1.9.9.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| ENFTEntry | |||
| eNFTInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| eNFTTestState | 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.2 | ||
| This indicates whether the eNFTValue is within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| eNFTEnable | 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| eNFTCounter | 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| eNFTCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| eNFTCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| eNFTLatestError | 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| eNFTActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| eNFTMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| eNFTValue | 1.3.6.1.4.1.2696.3.2.1.9.9.2.1.10 | ||
| The current Equivalent Noise Floor expressed in dB, see the reference for the method of calculation. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| eNDTLPTable | 1.3.6.1.4.1.2696.3.2.1.9.9.3 | ||
| Equivalent Noise Degradation measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If the transmission is not hierarchical, the MeasurementState for this table will be 'unknown'. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ENDTLPEntry | |||
| eNDTLPEntry | 1.3.6.1.4.1.2696.3.2.1.9.9.3.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| ENDTLPEntry | |||
| eNDTLPInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| eNDTLPTestState | 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.2 | ||
| This indicates whether eNDTLPValue is within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| eNDTLPEnable | 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| eNDTLPCounter | 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| eNDTLPCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| eNDTLPCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| eNDTLPLatestError | 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| eNDTLPActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| eNDTLPMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| eNDTLPValue | 1.3.6.1.4.1.2696.3.2.1.9.9.3.1.10 | ||
| The current Equivalent Noise Degradation for the low priority stream expressed in dB. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| eNFTLPTable | 1.3.6.1.4.1.2696.3.2.1.9.9.4 | ||
| Equivalent Noise Floor measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If the transmission is not hierarchical, the MeasurementState for this table will be 'unknown'. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ENFTLPEntry | |||
| eNFTLPEntry | 1.3.6.1.4.1.2696.3.2.1.9.9.4.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| ENFTLPEntry | |||
| eNFTLPInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| eNFTLPTestState | 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.2 | ||
| This indicates whether eNFTLPValue is within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| eNFTLPEnable | 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| eNFTLPCounter | 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| eNFTLPCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| eNFTLPCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| eNFTLPLatestError | 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| eNFTLPActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| eNFTLPMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| eNFTLPValue | 1.3.6.1.4.1.2696.3.2.1.9.9.4.1.10 | ||
| The current Equivalent Noise Floor for the low priority stream, expressed in dB, see the reference for the method of calculation. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| linearityTable | 1.3.6.1.4.1.2696.3.2.1.9.10 | ||
| Linearity characterization (shoulder attenuation) | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LinearityEntry | |||
| linearityEntry | 1.3.6.1.4.1.2696.3.2.1.9.10.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| LinearityEntry | |||
| linearityInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.10.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| linearityTestState | 1.3.6.1.4.1.2696.3.2.1.9.10.1.2 | ||
| This indicates whether the linearityValue is above the minimum permitted. | |||
| OBJECT-TYPE | |||
| TestState | |||
| linearityEnable | 1.3.6.1.4.1.2696.3.2.1.9.10.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| linearityCounter | 1.3.6.1.4.1.2696.3.2.1.9.10.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| linearityCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.10.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| linearityCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.10.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| linearityLatestError | 1.3.6.1.4.1.2696.3.2.1.9.10.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| linearityActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.10.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| linearityMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.10.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| linearityValue | 1.3.6.1.4.1.2696.3.2.1.9.10.1.10 | ||
| The current linearity (shoulder attenuation) expressed in dB. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| berViterbiT | 1.3.6.1.4.1.2696.3.2.1.9.15 | ||
| OBJECT IDENTIFIER | |||
| berViterbiTTable | 1.3.6.1.4.1.2696.3.2.1.9.15.1 | ||
| BER before Viterbi measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If the transmission is not hierarchical, this table contains the measurement for the whole stream. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BerViterbiTEntry | |||
| berViterbiTEntry | 1.3.6.1.4.1.2696.3.2.1.9.15.1.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| BerViterbiTEntry | |||
| berViterbiTInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| berViterbiTTestState | 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.2 | ||
| This indicates whether the berViterbiTValue is within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| berViterbiTEnable | 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| berViterbiTCounter | 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| berViterbiTCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| berViterbiTCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| berViterbiTLatestError | 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| berViterbiTActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| berViterbiTMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| berViterbiTValue | 1.3.6.1.4.1.2696.3.2.1.9.15.1.1.10 | ||
| This is the overall pre-Viterbi BER value, for example 0.0000046 | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| berViterbiTLPTable | 1.3.6.1.4.1.2696.3.2.1.9.15.2 | ||
| BER before Viterbi measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If the transmission is not hierarchical, the MeasurementState for this table will be 'unknown'. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BerViterbiTLPEntry | |||
| berViterbiTLPEntry | 1.3.6.1.4.1.2696.3.2.1.9.15.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| BerViterbiTLPEntry | |||
| berViterbiTLPInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| berViterbiTLPTestState | 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.2 | ||
| This indicates whether the berViterbiTLPValue is within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| berViterbiTLPEnable | 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| berViterbiTLPCounter | 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| berViterbiTLPCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| berViterbiTLPCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| berViterbiTLPLatestError | 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| berViterbiTLPActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| berViterbiTLPMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| berViterbiTLPValue | 1.3.6.1.4.1.2696.3.2.1.9.15.2.1.10 | ||
| This is the overall pre-Viterbi BER value, for example 0.0000046 | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| berRS | 1.3.6.1.4.1.2696.3.2.1.9.16 | ||
| OBJECT IDENTIFIER | |||
| berRSTable | 1.3.6.1.4.1.2696.3.2.1.9.16.1 | ||
| BER before RS measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the HP (high priority) stream. If the transmission is not hierarchical, this table contains the measurement for the whole stream. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BerRSEntry | |||
| berRSEntry | 1.3.6.1.4.1.2696.3.2.1.9.16.1.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| BerRSEntry | |||
| berRSInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| berRSTestState | 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.2 | ||
| This indicates whether berRSValue is below the maximum. | |||
| OBJECT-TYPE | |||
| TestState | |||
| berRSEnable | 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| berRSCounter | 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| berRSCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| berRSCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| berRSLatestError | 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| berRSActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| berRSMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| berRSValue | 1.3.6.1.4.1.2696.3.2.1.9.16.1.1.10 | ||
| This is the BER before RS (outer) decoder measured using the in-service method. It is expressed as a number, e.g. 0.0000034 | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| berRSLPTable | 1.3.6.1.4.1.2696.3.2.1.9.16.2 | ||
| BER before RS measurement. If the DVB-T transmission is hierarchical, this table contains the measurement for the LP (low priority) stream. If the transmission is not hierarchical, the MeasurementState for this table will be 'unknown'. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BerRSLPEntry | |||
| berRSLPEntry | 1.3.6.1.4.1.2696.3.2.1.9.16.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| BerRSLPEntry | |||
| berRSLPInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| berRSLPTestState | 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.2 | ||
| This indicates whether berRSLPValue is within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| berRSLPEnable | 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| berRSLPCounter | 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| berRSLPCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| berRSLPCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| berRSLPLatestError | 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| berRSLPActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| berRSLPMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| berRSLPValue | 1.3.6.1.4.1.2696.3.2.1.9.16.2.1.10 | ||
| This is the BER before RS (outer) decoder for the low priority stream measured using the in-service method. It is expressed as a number, e.g. 0.0000034 | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| iqAnalysisT | 1.3.6.1.4.1.2696.3.2.1.9.18 | ||
| OBJECT IDENTIFIER | |||
| merTTable | 1.3.6.1.4.1.2696.3.2.1.9.18.2 | ||
| Modulation Error Ratio (MER) measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MerTEntry | |||
| merTEntry | 1.3.6.1.4.1.2696.3.2.1.9.18.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| MerTEntry | |||
| merTInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| merTTestState | 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.2 | ||
| This indicates whether merTValue is within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| merTEnable | 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| merTCounter | 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| merTCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.5 | ||
| Provides the last time at which there was a discontinuity in the merTCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| merTCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| merTLatestError | 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| merTActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| merTMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| merTValue | 1.3.6.1.4.1.2696.3.2.1.9.18.2.1.10 | ||
| The current Modulation Error Ratio expressed in dB | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| steT | 1.3.6.1.4.1.2696.3.2.1.9.18.3 | ||
| OBJECT IDENTIFIER | |||
| steMeanTTable | 1.3.6.1.4.1.2696.3.2.1.9.18.3.1 | ||
| System Target Error Mean (STEM) measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SteMeanTEntry | |||
| steMeanTEntry | 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| SteMeanTEntry | |||
| steMeanTInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| steMeanTTestState | 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.2 | ||
| This indicates whether steMeanTValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| steMeanTEnable | 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| steMeanTCounter | 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| steMeanTCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| steMeanTCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| steMeanTLatestError | 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| steMeanTActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| steMeanTMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| steMeanTValue | 1.3.6.1.4.1.2696.3.2.1.9.18.3.1.1.10 | ||
| The current System Target Error Mean as a numeric value | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| steDeviationTTable | 1.3.6.1.4.1.2696.3.2.1.9.18.3.2 | ||
| System Target Error Deviation (STED) measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SteDeviationTEntry | |||
| steDeviationTEntry | 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| SteDeviationTEntry | |||
| steDeviationTInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| steDeviationTTestState | 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.2 | ||
| This indicates whether steDeviationTValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| steDeviationTEnable | 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| steDeviationTCounter | 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| steDeviationTCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| steDeviationTCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| steDeviationTLatestError | 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| steDeviationTActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| steDeviationTMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| steDeviationTValue | 1.3.6.1.4.1.2696.3.2.1.9.18.3.2.1.10 | ||
| The current System Target Error Deviation as a numeric value | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| csTTable | 1.3.6.1.4.1.2696.3.2.1.9.18.4 | ||
| Carrier Suppression (CS) measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CsTEntry | |||
| csTEntry | 1.3.6.1.4.1.2696.3.2.1.9.18.4.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| CsTEntry | |||
| csTInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| csTTestState | 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.2 | ||
| This indicates whether csTValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| csTEnable | 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| csTCounter | 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| csTCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| csTCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| csTLatestError | 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| csTActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| csTMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| csTValue | 1.3.6.1.4.1.2696.3.2.1.9.18.4.1.10 | ||
| The current Carrier Suppression value in dB. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| aiTTable | 1.3.6.1.4.1.2696.3.2.1.9.18.5 | ||
| Amplitude Imbalance (AI) measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AiTEntry | |||
| aiTEntry | 1.3.6.1.4.1.2696.3.2.1.9.18.5.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| AiTEntry | |||
| aiTInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| aiTTestState | 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.2 | ||
| This indicates whether aiTValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| aiTEnable | 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| aiTCounter | 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| aiTCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| aiTCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| aiTLatestError | 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| aiTActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| aiTMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| aiTValue | 1.3.6.1.4.1.2696.3.2.1.9.18.5.1.10 | ||
| The current Amplitude Imbalance as a percentage | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| qeTTable | 1.3.6.1.4.1.2696.3.2.1.9.18.6 | ||
| Quadrature Error (QE) measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| QeTEntry | |||
| qeTEntry | 1.3.6.1.4.1.2696.3.2.1.9.18.6.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| QeTEntry | |||
| qeTInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| qeTTestState | 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.2 | ||
| This indicates whether qeTValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| qeTEnable | 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| qeTCounter | 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| qeTCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| qeTCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| qeTLatestError | 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| qeTActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| qeTMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| qeTValue | 1.3.6.1.4.1.2696.3.2.1.9.18.6.1.10 | ||
| The current Quadrature Error value in degrees. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| pjTTable | 1.3.6.1.4.1.2696.3.2.1.9.18.7 | ||
| Phase Jitter (PJ) measurement | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PjTEntry | |||
| pjTEntry | 1.3.6.1.4.1.2696.3.2.1.9.18.7.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| PjTEntry | |||
| pjTInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| pjTTestState | 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.2 | ||
| This indicates whether pjTValue is currently within the thresholds. | |||
| OBJECT-TYPE | |||
| TestState | |||
| pjTEnable | 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| pjTCounter | 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.4 | ||
| Count of the number of times a threshold error has occurred for this measurement. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pjTCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| pjTCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| pjTLatestError | 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.7 | ||
| The timestamp at the most recent occurrence of a threshold error on this measurement. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| pjTActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| pjTMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| pjTValue | 1.3.6.1.4.1.2696.3.2.1.9.18.7.1.10 | ||
| The current Phase Jitter value in degrees. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| mipSyntaxTable | 1.3.6.1.4.1.2696.3.2.1.9.20 | ||
| SFN MIP baseband tests | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MipSyntaxEntry | |||
| mipSyntaxEntry | 1.3.6.1.4.1.2696.3.2.1.9.20.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| MipSyntaxEntry | |||
| mipSyntaxInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.20.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| mipSyntaxTestNumber | 1.3.6.1.4.1.2696.3.2.1.9.20.1.2 | ||
| The specific SFN MIP test that this row applies to | |||
| OBJECT-TYPE | |||
| IndexMIPSyntaxTest | |||
| mipSyntaxState | 1.3.6.1.4.1.2696.3.2.1.9.20.1.3 | ||
| This gives the overall pass/fail state of the test. | |||
| OBJECT-TYPE | |||
| TestState | |||
| mipSyntaxEnable | 1.3.6.1.4.1.2696.3.2.1.9.20.1.4 | ||
| Determines whether this test and the associated trap are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| mipSyntaxCounter | 1.3.6.1.4.1.2696.3.2.1.9.20.1.5 | ||
| Count of the number of times this error has occurred | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| mipSyntaxCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.20.1.6 | ||
| Provides the last time at which there was a discontinuity in the mipSyntaxCounter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| mipSyntaxCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.20.1.7 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| mipSyntaxLatestError | 1.3.6.1.4.1.2696.3.2.1.9.20.1.8 | ||
| The timestamp at the most recent occurrence of the error | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| mipSyntaxActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.20.1.9 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| systemErrorPerformance | 1.3.6.1.4.1.2696.3.2.1.9.21 | ||
| OBJECT IDENTIFIER | |||
| sepEtiTable | 1.3.6.1.4.1.2696.3.2.1.9.21.1 | ||
| Measurement of Errored Second Ratio (ESR) or Errored Time Interval Ratio (ETIR). | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SepEtiEntry | |||
| sepEtiEntry | 1.3.6.1.4.1.2696.3.2.1.9.21.1.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| SepEtiEntry | |||
| sepEtiInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| sepEtiTestState | 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.2 | ||
| A 'fail' indicaties that the most recently completed time interval TI was an Errored Time Interval (ETI). A 'pass' indicates that the most recent TI was not errored. | |||
| OBJECT-TYPE | |||
| TestState | |||
| sepEtiEnable | 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| sepEtiCounter | 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.4 | ||
| Count of the number of times an ETI has occurred. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| sepEtiCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| sepEtiCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| sepEtiLatestError | 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.7 | ||
| The timestamp at the most recent occurrence of an ETI. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| sepEtiActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| sepEtiMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| sepEtiValue | 1.3.6.1.4.1.2696.3.2.1.9.21.1.1.10 | ||
| This is the Errored Time Interval Ratio (ETIR) for the most recently completed Measurement Interval (MI). It is expressed as a numeric value. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| sepSetiTable | 1.3.6.1.4.1.2696.3.2.1.9.21.2 | ||
| Measurement of Severly Errored Second Ratio (SESR) or Severely Errored Time Interval Ratio (SETIR). | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SepSetiEntry | |||
| sepSetiEntry | 1.3.6.1.4.1.2696.3.2.1.9.21.2.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| SepSetiEntry | |||
| sepSetiInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.1 | ||
| Transport Stream on which the measurement is made | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| sepSetiTestState | 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.2 | ||
| A 'fail' indicaties that the most recently completed time interval TI was a Severely Errored Time Interval (SETI). A 'pass' indicates that the most recent TI was not severely errored. | |||
| OBJECT-TYPE | |||
| TestState | |||
| sepSetiEnable | 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.3 | ||
| Determines whether the threshold test and associated traps for this measurement are enabled. | |||
| OBJECT-TYPE | |||
| Enable | |||
| sepSetiCounter | 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.4 | ||
| Count of the number of times an SETI has occurred. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| sepSetiCounterDiscontinuity | 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.5 | ||
| Provides the last time at which there was a discontinuity in the counter object. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| sepSetiCounterReset | 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.6 | ||
| The counter object is reset to zero and the counter discontinuity object is set to the current time if 'true' is written to this object. When read, the value of this object is always 'false'. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| sepSetiLatestError | 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.7 | ||
| The timestamp at the most recent occurrence of a SETI. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| sepSetiActiveTime | 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.8 | ||
| The total time when it has been possible to perform this measurement | |||
| OBJECT-TYPE | |||
| ActiveTime | |||
| sepSetiMeasurementState | 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.9 | ||
| Specifies the validity of the measurement value | |||
| OBJECT-TYPE | |||
| MeasurementState | |||
| sepSetiValue | 1.3.6.1.4.1.2696.3.2.1.9.21.2.1.10 | ||
| This is the Severely Errored Time Interval Ratio (SETIR) for the most recently completed Measurement Interval (MI). It is expressed as a numeric value. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPreferencesTable | 1.3.6.1.4.1.2696.3.2.1.9.100 | ||
| Table of terrestrial specific measurement preferences. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TerrestrialPreferencesEntry | |||
| terrestrialPreferencesEntry | 1.3.6.1.4.1.2696.3.2.1.9.100.1 | ||
| Row specification | |||
| OBJECT-TYPE | |||
| TerrestrialPreferencesEntry | |||
| terrestrialPrefInputNumber | 1.3.6.1.4.1.2696.3.2.1.9.100.1.1 | ||
| Transport Stream input to which the preferences apply | |||
| OBJECT-TYPE | |||
| InputNumber | |||
| terrestrialPrefCentreFrequency | 1.3.6.1.4.1.2696.3.2.1.9.100.1.2 | ||
| This is the centre frequency to which the measuring equipment is tuned for making terrestrial measurements. This frequency is the actual input frequency to the measuring equipment, which may be at an intermediate frequency (IF) rather than the final RF. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefBandwidth | 1.3.6.1.4.1.2696.3.2.1.9.100.1.3 | ||
| The instrument is set to expect a DVB-T transmission adapted for this bandwidth. Normal values will be 6.0MHz, 7.0MHz or 8.0MHz. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefModulation | 1.3.6.1.4.1.2696.3.2.1.9.100.1.4 | ||
| This is the modulation which the measuring equipment expects to see and against which it makes modulation measurements. This applies to terrestrial measurements. | |||
| OBJECT-TYPE | |||
| Modulation | |||
| terrestrialPrefTransmissionMode | 1.3.6.1.4.1.2696.3.2.1.9.100.1.5 | ||
| The instrument is set to expect a transmission in either 2k mode or 8k mode as set by this object. | |||
| OBJECT-TYPE | |||
| TerrestrialTransmissionMode | |||
| terrestrialPrefGuardInterval | 1.3.6.1.4.1.2696.3.2.1.9.100.1.6 | ||
| The instrument is set to expect a transmission using the guard interval specified by this object. | |||
| OBJECT-TYPE | |||
| GuardInterval | |||
| terrestrialPrefHierarchical | 1.3.6.1.4.1.2696.3.2.1.9.100.1.7 | ||
| The instrument is set according to the value of this object to expect a transmission which is either non-hierachical or hierarchical using the specified alpha value. | |||
| OBJECT-TYPE | |||
| Hierarchy | |||
| terrestrialPrefCentreFreqExpected | 1.3.6.1.4.1.2696.3.2.1.9.100.1.8 | ||
| This is the expected value for the centre frequency as measured by rfAccuracyValue. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefCentreFreqLimit | 1.3.6.1.4.1.2696.3.2.1.9.100.1.9 | ||
| This is the permitted deviation for the centre frequency as measured by rfAccuracyValue. If rfAccuracyValue is outside the range: [terrestrialPrefCentreFreqExpected - terrestrialPrefCentreFreqLimit .. terrestrialPrefCentreFreqExpected + terrestrialPrefCentreFreqLimit] an error will be indicated. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefChannelWidthLimit | 1.3.6.1.4.1.2696.3.2.1.9.100.1.10 | ||
| This is the permitted deviation for the channel width as measured by rfChannelWidthValue. The nominal value of the channel width has a fixed value which depends on the bandwidth (as set by terrestrialPrefBandwidth). If rfChannelWidthValue is outside the range [nominalWidth - terrestrialPrefChannelWidthLimit .. nominalWidth + terrestrialPrefChannelWidthLimit] an error will be indicated. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefSymbolLengthLimit | 1.3.6.1.4.1.2696.3.2.1.9.100.1.11 | ||
| This is the permitted deviation for the symbol length as measured by symbolLengthValue. The nominal value of the symbol length has a fixed value which depends on the bandwidth, the mode and the guard interval (as set by terrestrialPrefBandwidth, terrestrialPrefTransmissionMode and terrestrialPrefGuardInterval respectively). If symbolLengthValue is outside the range [nominalLength - terrestrialPrefSymbolLengthLimit .. nominalLength + terrestrialPrefSymbolLengthLimit] an error will be indicated. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefPowerMin | 1.3.6.1.4.1.2696.3.2.1.9.100.1.12 | ||
| If the power measured by rfIfPowerValue is less than this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefPowerMax | 1.3.6.1.4.1.2696.3.2.1.9.100.1.13 | ||
| If the power measured by rfIfPowerValue is greater than this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefENDBER | 1.3.6.1.4.1.2696.3.2.1.9.100.1.14 | ||
| BER value which is to be used for the END and ENF measurements. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefENDIdeal | 1.3.6.1.4.1.2696.3.2.1.9.100.1.15 | ||
| This is the 'ideal' value of C/N for measurement of END on the whole or high priority stream. It is used in the measurement of eNDTValue. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefENDMax | 1.3.6.1.4.1.2696.3.2.1.9.100.1.16 | ||
| If the measured value of eNDTValue exceeds this, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefENFIdeal | 1.3.6.1.4.1.2696.3.2.1.9.100.1.17 | ||
| This is the 'ideal' value of C/N for measurement of ENF on the whole or high priority stream. It is used in the measurement of eNFTValue. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefENFMax | 1.3.6.1.4.1.2696.3.2.1.9.100.1.18 | ||
| If the measured value of eNFTValue is exceeds this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefENDLPIdeal | 1.3.6.1.4.1.2696.3.2.1.9.100.1.19 | ||
| This is the 'ideal' value of C/N for measurement of END on the low priority stream. It is used in the measurement of eNDTLPValue. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefENDLPMax | 1.3.6.1.4.1.2696.3.2.1.9.100.1.20 | ||
| If the measured value of eNDTLPValue exceeds this, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefENFLPIdeal | 1.3.6.1.4.1.2696.3.2.1.9.100.1.21 | ||
| This is the 'ideal' value of C/N for measurement of ENF on the low priority stream. It is used in the measurement of eNFTLPValue. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefENFLPMax | 1.3.6.1.4.1.2696.3.2.1.9.100.1.22 | ||
| If the measured value of eNFTLPValue exeeds this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefLinearityMin | 1.3.6.1.4.1.2696.3.2.1.9.100.1.23 | ||
| If the shoulder attenuation as measured by linearityValue is less than this value, an error is indicated. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefBERViterbiMax | 1.3.6.1.4.1.2696.3.2.1.9.100.1.24 | ||
| If the BER measured by berViterbiTValue exceeds this value, an error is indicated. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefBERViterbiLPMax | 1.3.6.1.4.1.2696.3.2.1.9.100.1.25 | ||
| If the BER measured by berViterbiTLPValue exceeds this value, an error is indicated. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefBERRSMax | 1.3.6.1.4.1.2696.3.2.1.9.100.1.26 | ||
| If the BER measured by berRSValue exceeds this value, an error is indicated. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefBERRSLPMax | 1.3.6.1.4.1.2696.3.2.1.9.100.1.27 | ||
| If the BER measured by berRSLPValue exceeds this value, an error is indicated. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefMerTMin | 1.3.6.1.4.1.2696.3.2.1.9.100.1.28 | ||
| If merTValue is less than this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefSteMeanMax | 1.3.6.1.4.1.2696.3.2.1.9.100.1.29 | ||
| If steMeanTValue exceeds this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefSteDeviationMax | 1.3.6.1.4.1.2696.3.2.1.9.100.1.30 | ||
| If steDeviationTValue exceeds this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefCsMin | 1.3.6.1.4.1.2696.3.2.1.9.100.1.31 | ||
| If csTValue is less than this value, the associated test fails | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefAiMax | 1.3.6.1.4.1.2696.3.2.1.9.100.1.32 | ||
| If aiTValue exceeds this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefQeMax | 1.3.6.1.4.1.2696.3.2.1.9.100.1.33 | ||
| If qeTValue exceeds this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefPjMax | 1.3.6.1.4.1.2696.3.2.1.9.100.1.34 | ||
| If pjTValue exceeds this value, the associated test fails. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefMIPTimingLimit | 1.3.6.1.4.1.2696.3.2.1.9.100.1.35 | ||
| This preference affects the MIP_timing_error test. If the calculated value of nT differs from an integral number of seconds by more than terrestrialPrefMIPTimingLimit then an error is indicated. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefMIPDeviationMax | 1.3.6.1.4.1.2696.3.2.1.9.100.1.36 | ||
| This preference affects the MIP_ts_rate_error test. It is the value of Max_deviation in the inequality given in TR 101 290 as the condition for an error indication. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefSEPUATMode | 1.3.6.1.4.1.2696.3.2.1.9.100.1.37 | ||
| Determines whether the 'N consecutive' or 'rolling window' mode of determining the start of a period of Unavailable Time (UAT) is used. If the 'N consecutive' mode is selected, the 'M' and 'T' preference parameters are ignored. Likewise, if the 'rolling window' mode is selected, the 'N' preference parameter is ignored. | |||
| OBJECT-TYPE | |||
| UATMode | |||
| terrestrialPrefSEPN | 1.3.6.1.4.1.2696.3.2.1.9.100.1.38 | ||
| The N value used to identify the start and end of a period of unavailable time (UAT). | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| terrestrialPrefSEPT | 1.3.6.1.4.1.2696.3.2.1.9.100.1.39 | ||
| The T value used to identify the start and end of a period of unavailable time (UAT). | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefSEPM | 1.3.6.1.4.1.2696.3.2.1.9.100.1.40 | ||
| The M value used to identify the start and end of a period of unavailable time (UAT). | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| terrestrialPrefSEPTI | 1.3.6.1.4.1.2696.3.2.1.9.100.1.41 | ||
| Each Time Interval of this length is assessed as to whether it is an Errored Time Interval or a Severely Errored Time Interval. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefSEPEBPerCent | 1.3.6.1.4.1.2696.3.2.1.9.100.1.42 | ||
| If more than this percentage of blocks within a Time Interval is an Errored Block, the Time Interval is a Severely Errored Time Interval (SETI). Example values are: '1.53', '10', '0.33'. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| terrestrialPrefSEPMeasurementInterval | 1.3.6.1.4.1.2696.3.2.1.9.100.1.43 | ||
| The Measurement Interval (MI) over which the ESR/ETIR and SESR/SETIR are calculated. | |||
| OBJECT-TYPE | |||
| FloatingPoint | |||
| tr101290Conformance | 1.3.6.1.4.1.2696.3.2.3 | ||
| OBJECT IDENTIFIER | |||
| tr101290Compliances | 1.3.6.1.4.1.2696.3.2.3.1 | ||
| OBJECT IDENTIFIER | |||
| complianceTransportStream | 1.3.6.1.4.1.2696.3.2.3.1.1 | ||
| Compliance for Transport Stream monitor devices | |||
| MODULE-COMPLIANCE | |||
| complianceCable | 1.3.6.1.4.1.2696.3.2.3.1.2 | ||
| Compliance for Cable RF measurement devices | |||
| MODULE-COMPLIANCE | |||
| complianceSatellite | 1.3.6.1.4.1.2696.3.2.3.1.3 | ||
| Compliance for Satellite RF measurement devices | |||
| MODULE-COMPLIANCE | |||
| complianceTerrestrial | 1.3.6.1.4.1.2696.3.2.3.1.4 | ||
| Compliance for Terrestrial RF measurement devices | |||
| MODULE-COMPLIANCE | |||
| tr101290ObjectGroups | 1.3.6.1.4.1.2696.3.2.3.2 | ||
| OBJECT IDENTIFIER | |||
| groupControl | 1.3.6.1.4.1.2696.3.2.3.2.1 | ||
| Contains all the objects from the tr101290Control branch of the MIB | |||
| OBJECT-GROUP | |||
| groupTrapControl | 1.3.6.1.4.1.2696.3.2.3.2.2 | ||
| Contains all the normal objects from the tr101290Trap branch of the MIB | |||
| OBJECT-GROUP | |||
| groupTraps | 1.3.6.1.4.1.2696.3.2.3.2.3 | ||
| Contains all the traps/notifications from the MIB. | |||
| NOTIFICATION-GROUP | |||
| groupCapability | 1.3.6.1.4.1.2696.3.2.3.2.4 | ||
| Contains all objects from the tr101290Capability branch of the MIB | |||
| OBJECT-GROUP | |||
| groupTransportStream | 1.3.6.1.4.1.2696.3.2.3.2.5 | ||
| Contains all objects relevant to Transport Stream measurement | |||
| OBJECT-GROUP | |||
| groupCable | 1.3.6.1.4.1.2696.3.2.3.2.6 | ||
| Contains all objects relevant to cable RF measurement | |||
| OBJECT-GROUP | |||
| groupSatellite | 1.3.6.1.4.1.2696.3.2.3.2.7 | ||
| Contains all objects relevent to satellite RF measurements | |||
| OBJECT-GROUP | |||
| groupTerrestrial | 1.3.6.1.4.1.2696.3.2.3.2.8 | ||
| Contains all objects relevant to terrestrial RF measurements | |||
| OBJECT-GROUP | |||
| ActiveTime | |||
| This is a monotonically increasing value in units of seconds that represents the total amount of time for which the instrument has been able to perform a particular test or measurement. The instrument might not be performing the test because some other error condition prevented it, because it was operating in a polled mode where it looked at one input at a time or because it had been placed in an inactive state for a while. 'Able to perform the test' corresponds to the TestState being either 'pass' or 'fail'. The existence of this attribute allows a management system to calculate a realistic errors per second value for any test. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | |||
| Availability | |||
| Availability is used in the capabilities branch of the MIB to indicate whether the instrument is equipped to provide a specific test and/or measurement. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | notAvailable(1), testAvailable(2), measurementAvailable(3), measurementAndTestAvailable(4) | ||
| BERMeasurementMethod | |||
| Indicates the method used for measuring BER before Viterbi decoding | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | iqSeparate(1), iqCombined(2) | ||
| BitRateElement | |||
| The fundamental data unit that is being counted by the bit rate measurement algorithm. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | bit(1), byte(2), packet(3), other(4) | ||
| DeliverySystemType | |||
| Specifies the physical delivery system used for a Transport Stream. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | unknown(1), cable(2), satellite(3), terrestrial(4) | ||
| Enable | |||
| This type is used for the '...Enable' objects of tests and measurements. It determines whether the test is enabled and also which traps can be generated by this test/measurement. If the testEnable bit is zero, the test will not be performed and the failTrapEnable bit is ignored. If the testEnable bit is one, the test will be performed. Additionally, a testFailTrap or measurementFailTrap will be sent when the test state becomes 'fail'. The 'unknownTrapEnable' bit is only relevant to measurements. If it is set to one, a 'measurementUnknownTrap' will be sent when the '...MeasurementState' object becomes 'unknown'. | |||
| TEXTUAL-CONVENTION | |||
| BITS | testEnable(0), failTrapEnable(1), unknownTrapEnable(2) | ||
| FloatingPoint | |||
| FloatingPoint provides a way of representing non-integer numbers in SNMP. Numbers are represented as a string of ASCII characters in the natural way. So for example, '3', '3.142' and '0.3142E1' are all valid numbers. The syntax for the string is as follows. [] enclose an optional element, | is the separator for a set of alternatives. () enclose syntax which is to be viewed as a unit. FloatingPoint ::= [Sign] (Float1 | Float2 | DigitSequence) [ExponentPart] Float1 ::= DigitSequence '.' [DigitSequence] Float2 ::= '.' DigitSequence DigitSequence ::= Digit [DigitSequence] ExponentPart ::= ('e' | 'E') [Sign] DigitSequence Digit ::= '0'..'9' Sign ::= '+' | '-' | |||
| TEXTUAL-CONVENTION | |||
| OCTET STRING | SIZE(1..63) | ||
| GroupAvailability | |||
| This is used in the tr101290Capability branch of the MIB to specify an agent's degree of support for a whole branch of the MIB. The individual values mean: noSupport no objects in this branch are available selectiveSupport some but not all objects are available, refer to the test table for further details completeSupport all objects defined in the stated revision of the MIB are available | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | noSupport(1), selectiveSupport(2), completeSupport(3) | ||
| GuardInterval | |||
| Guard intervals as specified for DVB-T transmissions. interval1d4 means a guard interval of 1/4. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | interval1d4(1), interval1d8(2), interval1d16(3), interval1d32(4) | ||
| Hierarchy | |||
| In DVB-T systems this is used to specify whether the transmission is hierarchical, and if so, the value of alpha. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | nonHierarchical(1), hierarchicalAlphaOne(2), hierarchicalAphaTwo(3), hierarchicalAlphaFour(4) | ||
| IndexConsistencyTest | |||
| Index of consistency check tests | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | tsIdCheck(1) | ||
| IndexMIPSyntaxTest | |||
| This assigns numbers to the MIP syntax tests. These numbers are then used as indexes into the MIP syntax table. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | mipTimingError(1), mipStructureError(2), mipPresenceError(3), mipPointerError(4), mipPeriodicityError(5), mipTsRateError(6) | ||
| IndexPCRMeasurement | |||
| This assigns numbers to the PCR measurements. These numbers are then used as indexes into the PCR measurement table. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | pcrFO(1), pcrDR(2), pcrOJ(3), pcrAC(4) | ||
| IndexServicePerformance | |||
| This assigns numbers to the Service Performance measurements. These numbers are then used as indexes into the Service Performance measurement table. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | serviceAvailability(1), serviceDegradation(2), serviceImpairments(3) | ||
| IndexTransportStreamTest | |||
| IndexTransportStreamTest assigns a unique numerical value to each of the TR 101 290 Transport Stream tests in section 5.2. The number allocated is: priority * 1000 + test number * 10 + subtest Subtest is zero if there is no subtest. Subtest 'a' is numbered 1, 'b' is numbered 2 etc. The enumeration names are derived directly from the test names in TR 101 290 taking into account the syntax requirements of the MIB. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | tsSyncLoss(1010), syncByteError(1020), patError2(1031), continuityCountError(1040), pmtError2(1051), pidError(1060), transportError(2010), crcError(2020), pcrRepetitionError(2031), pcrDiscontinuityError(2032), pcrAccuracyError(2040), ptsError(2050), catError(2060), nitActualError(3011), nitOtherError(3012), siRepetitionError(3020), bufferError(3030), unreferencedPID(3041), sdtActualError(3051), sdtOtherError(3052), eitActualError(3061), eitOtherError(3062), eitPfError(3063), rstError(3070), tdtError(3080), emptyBufferError(3090), dataDelayError(3100) | ||
| InputNumber | |||
| InputNumber objects are used to select a specific Transport Stream input on a multi-input monitoring/measurement device. On a single input monitoring/measuring device, InputNumber objects will always have the value one. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | 1..2147483647 | ||
| MeasurementState | |||
| MeasurementState is used to represent the state of a single measurement. 'disabled' means that the measurement has been disabled by setting the 'testEnable' bit in its ...Enable object to zero. 'unknown' means that the equipment cannot provide a value because of temporary circumstances, for example some other signal condition makes this measurement impossible. 'abnormal' means that the measurement value is incorrect for reasons connected with that measurement itself. For example the measurement may be out of range. A measurement value is still provided and users or managers with knowledge of the behaviour of this specific measuring equipment may be able to interpret the value. 'normal' means that the measurement is enabled and has been evaluated. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | disabled(1), unknown(2), normal(3), abnormal(4) | ||
| Modulation | |||
| Modulation systems used in RF transmissions | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | bpsk(1), qpsk(2), psk8(3), qam16(4), qam32(5), qam64(6), qam128(7), qam256(8), qam16Alpha2(9), qam64Alpha2(10), qam16Alpha4(11), qam64Alpha4(12) | ||
| PIDPlusOne | |||
| An object of type PIDPlusOne represents an MPEG-2 PID number. The numeric value of the object is the PID + 1, to allow for its use as a table index. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | 1..8192 | ||
| PollingInterval | |||
| Objects of this type are used by the agent to indicate how often it internally updates the information related to a particular test or measurement. The manager can then adjust its polling behaviour accordingly. The polling interval should be interpreted by the manager as approximate. In practice the agent may update the information faster or slower than indicated depending on the circumstances. The meaning of the value is: positive - represents a normal value in milliseconds zero - the value is updated continuously negative - unknown or not applicable | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | |||
| RateStatus | |||
| RateStatus is used in trap control | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | disabled(1), enabled(2), enabledThrottled(3) | ||
| ServiceId | |||
| Allowed values of program_number/service_id. Note that zero is used in the PAT to represent the NIT PID and so will never occur as a service_id. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | 1..65535 | ||
| TerrestrialTransmissionMode | |||
| Transmission mode for DVB-T transmissions, specifies whether there are 2k or 8k carriers. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | mode2k(1), mode8k(2) | ||
| TestState | |||
| TestState is used to represent the state of a single test. 'disabled' means that the test has been disabled by setting the 'testEnable' bit of its ...Enable variable to zero. 'unknown' means that the equipment cannot provide a value for the state because of temporary circumstances (for example some other error makes this test impossible to evaluate). 'pass' means that the test is enabled, can be evaluated and is not failing. For a 'Status error', 'fail' means that the state of the input is currently in error. For an 'Event error', 'fail' means that an error event has occurred within the most recent persistence interval as defined by the 'controlEventPersistence' object. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | disabled(1), unknown(2), pass(3), fail(4) | ||
| TestSummary | |||
| Bit String providing a status summary for all the tests defined in this MIB module. A bit is set to one if the state of that test is 'fail'. In several cases, a single bit summarises the results of a set of tests. In that case, if the state of any of the tests is 'fail', the bit is set to one. An example of this is 'bitratePID' where the single bit summarises whether all the PID bitrates are within range. To aid identification, the bits are numbered in the order in which the associated tests appear in the MIB. Other than this, there is no connection between the bit number and the OID of the test. | |||
| TEXTUAL-CONVENTION | |||
| BITS | tsTsSyncLoss(0), tsSyncByteError(1), tsPatError2(2), tsContinuityCountError(3), tsPmtError2(4), tsPidError(5), tsTransportError(6), tsCrcError(7), tsPcrRepetitionError(8), tsPcrDiscontinuityError(9), tsPcrAccuracyError(10), tsPtsError(11), tsCatError(12), tsNitActualError(13), tsNitOtherError(14), tsSiRepetitionError(15), tsBufferError(16), tsUnreferencedPID(17), tsSdtActualError(18), tsSdtOtherError(19), tsEitActualError(20), tsEitOtherError(21), tsEitPfError(22), tsRstError(23), tsTdtError(24), tsEmptyBufferError(25), tsDataDelayError(26), pcrPcrFO(27), pcrPcrDR(28), pcrPcrOJ(29), pcrPcrAC(30), bitrateTransportStream(31), bitrateService(32), bitratePID(33), tsTsConsistency(34), performanceServiceAvailability(35), performanceServiceDegradation(36), performanceServiceImpairments(37), csSysAvailability(38), csLinkAvailability(39), csBerRS(40), csRFIFSignalPower(41), csNoisePower(42), csMer(43), csSteMean(44), csSteDeviation(45), csCS(46), csAI(47), csQE(48), csRTE(49), csCI(50), csPJ(51), csSNR(52), cNoiseMargin(53), cEstNoiseMargin(54), cSignQualMarT(55), cEND(56), cOutBandEmiss(57), sBerViterbi(58), sIfSpectrum(59), tRFAccuracy(60), tRFChannelWidth(61), tSymbolLength(62), tRFIFPower(63), tRFIFSpectrum(64), tEND(65), tENF(66), tENDLP(67), tENFLP(68), tLinearity(69), tBerViterbi(70), tBerViterbiLP(71), tBerRS(72), tBerRSLP(73), tMER(74), tSteMean(75), tSteDeviation(76), tCS(77), tAI(78), tQE(79), tPJ(80), tMipTimingError(81), tMipStructureError(82), tMipPresenceError(83), tMipPointerError(84), tMipPeriodicityError(85), tMipTsRateError(86), tSepEti(87), tSepSeti(88) | ||
| TransportStreamID | |||
| Range of possible values for a transport_stream_id as found in the PAT. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | 0..65535 | ||
| UATMode | |||
| Method of determining the start and end of a period of Unavailable Time. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | nConsecutive(1), rollingWindow(2) | ||
| ControlRFSystemEntry | |||
| SEQUENCE | |||
| InputNumber as rfSystemInputNumber | |||
| DeliverySystemType as rfSystemDelivery | |||
| ControlSynchronizationEntry | |||
| SEQUENCE | |||
| InputNumber as controlSynchronizationInputNumber | |||
| FloatingPoint as controlSynchronizedTime | |||
| TrapControlEntry | |||
| SEQUENCE | |||
| InputNumber as trapControlInputNumber | |||
| OBJECT IDENTIFIER as trapControlOID | |||
| DateAndTime as trapControlGenerationTime | |||
| FloatingPoint as trapControlMeasurementValue | |||
| RateStatus as trapControlRateStatus | |||
| Unsigned32 as trapControlPeriod | |||
| TestSummary as trapControlFailureSummary | |||
| CapabilityTSEntry | |||
| SEQUENCE | |||
| OBJECT IDENTIFIER as capabilityTSOID | |||
| Availability as capabilityTSAvailability | |||
| PollingInterval as capabilityTSPollInterval | |||
| CapabilityCableSatEntry | |||
| SEQUENCE | |||
| OBJECT IDENTIFIER as capabilityCableSatOID | |||
| Availability as capabilityCableSatAvailability | |||
| PollingInterval as capabilityCableSatPollInterval | |||
| CapabilityCableEntry | |||
| SEQUENCE | |||
| OBJECT IDENTIFIER as capabilityCableOID | |||
| Availability as capabilityCableAvailability | |||
| PollingInterval as capabilityCablePollInterval | |||
| CapabilitySatelliteEntry | |||
| SEQUENCE | |||
| OBJECT IDENTIFIER as capabilitySatelliteOID | |||
| Availability as capabilitySatelliteAvailability | |||
| PollingInterval as capabilitySatellitePollInterval | |||
| CapabilityTerrestrialEntry | |||
| SEQUENCE | |||
| OBJECT IDENTIFIER as capabilityTerrestrialOID | |||
| Availability as capabilityTerrestrialAvailability | |||
| PollingInterval as capabilityTerrestrialPollInterval | |||
| TsTestsSummaryEntry | |||
| SEQUENCE | |||
| InputNumber as tsTestsSummaryInputNumber | |||
| IndexTransportStreamTest as tsTestsSummaryTestNumber | |||
| TestState as tsTestsSummaryState | |||
| Enable as tsTestsSummaryEnable | |||
| Counter32 as tsTestsSummaryCounter | |||
| DateAndTime as tsTestsSummaryCounterDiscontinuity | |||
| TruthValue as tsTestsSummaryCounterReset | |||
| DateAndTime as tsTestsSummaryLatestError | |||
| ActiveTime as tsTestsSummaryActiveTime | |||
| TsTestsPIDEntry | |||
| SEQUENCE | |||
| InputNumber as tsTestsPIDInputNumber | |||
| PIDPlusOne as tsTestsPIDPID | |||
| IndexTransportStreamTest as tsTestsPIDTestNumber | |||
| RowStatus as tsTestsPIDRowStatus | |||
| TestState as tsTestsPIDState | |||
| Enable as tsTestsPIDEnable | |||
| Counter32 as tsTestsPIDCounter | |||
| DateAndTime as tsTestsPIDCounterDiscontinuity | |||
| TruthValue as tsTestsPIDCounterReset | |||
| DateAndTime as tsTestsPIDLatestError | |||
| ActiveTime as tsTestsPIDActiveTime | |||
| TsTestsPreferencesEntry | |||
| SEQUENCE | |||
| InputNumber as tsTestsPrefInputNumber | |||
| FloatingPoint as tsTestsPrefTransitionDuration | |||
| FloatingPoint as tsTestsPrefPATSectionIntervalMax | |||
| FloatingPoint as tsTestsPrefPMTSectionIntervalMax | |||
| FloatingPoint as tsTestsPrefReferredIntervalMax | |||
| FloatingPoint as tsTestsPrefPCRIntervalMax | |||
| FloatingPoint as tsTestsPrefPCRDiscontinuityMax | |||
| FloatingPoint as tsTestsPrefPCRInaccuracyMax | |||
| FloatingPoint as tsTestsPrefPTSIntervalMax | |||
| FloatingPoint as tsTestsPrefNITActualIntervalMax | |||
| FloatingPoint as tsTestsPrefNITActualIntervalMin | |||
| FloatingPoint as tsTestsPrefNITOtherIntervalMax | |||
| FloatingPoint as tsTestsPrefSIGapMin | |||
| FloatingPoint as tsTestsPrefNITTableIntervalMax | |||
| FloatingPoint as tsTestsPrefBATTableIntervalMax | |||
| FloatingPoint as tsTestsPrefSDTActualTableIntervalMax | |||
| FloatingPoint as tsTestsPrefSDTOtherTableIntervalMax | |||
| FloatingPoint as tsTestsPrefEITPFActualTableIntervalMax | |||
| FloatingPoint as tsTestsPrefEITPFOtherTableIntervalMax | |||
| FloatingPoint as tsTestsPrefEITSActualNearTableIntervalMax | |||
| FloatingPoint as tsTestsPrefEITSActualFarTableIntervalMax | |||
| FloatingPoint as tsTestsPrefEITSOtherNearTableIntervalMax | |||
| FloatingPoint as tsTestsPrefEITSOtherFarTableIntervalMax | |||
| FloatingPoint as tsTestsPrefTxTTableIntervalMax | |||
| FloatingPoint as tsTestsPrefSDTActualIntervalMax | |||
| FloatingPoint as tsTestsPrefSDTActualIntervalMin | |||
| FloatingPoint as tsTestsPrefSDTOtherIntervalMax | |||
| FloatingPoint as tsTestsPrefEITActualIntervalMax | |||
| FloatingPoint as tsTestsPrefEITActualIntervalMin | |||
| FloatingPoint as tsTestsPrefEITOtherIntervalMax | |||
| FloatingPoint as tsTestsPrefRSTIntervalMin | |||
| FloatingPoint as tsTestsPrefTDTIntervalMax | |||
| FloatingPoint as tsTestsPrefTDTIntervalMin | |||
| TsTestsPreferencesPIDEntry | |||
| SEQUENCE | |||
| InputNumber as tsTestsPrefPIDInputNumber | |||
| PIDPlusOne as tsTestsPrefPIDPID | |||
| RowStatus as tsTestsPrefPIDRowStatus | |||
| FloatingPoint as tsTestsPrefPIDReferredIntervalMax | |||
| TsPcrMeasurementEntry | |||
| SEQUENCE | |||
| InputNumber as tsPcrMeasurementInputNumber | |||
| PIDPlusOne as tsPcrMeasurementPID | |||
| IndexPCRMeasurement as tsPcrMeasurementNumber | |||
| RowStatus as tsPcrMeasurementRowStatus | |||
| TestState as tsPcrMeasurementState | |||
| Enable as tsPcrMeasurementEnable | |||
| Counter32 as tsPcrMeasurementCounter | |||
| DateAndTime as tsPcrMeasurementCounterDiscontinuity | |||
| TruthValue as tsPcrMeasurementCounterReset | |||
| DateAndTime as tsPcrMeasurementLatestError | |||
| ActiveTime as tsPcrMeasurementActiveTime | |||
| MeasurementState as tsPcrMeasurementMeasurementState | |||
| FloatingPoint as tsPcrMeasurementValue | |||
| TsTransportStreamBitRateEntry | |||
| SEQUENCE | |||
| InputNumber as tsTransportStreamBitRateInputNumber | |||
| TestState as tsTransportStreamBitRateState | |||
| Enable as tsTransportStreamBitRateEnable | |||
| Counter32 as tsTransportStreamBitRateCounter | |||
| DateAndTime as tsTransportStreamBitRateCounterDiscontinuity | |||
| TruthValue as tsTransportStreamBitRateCounterReset | |||
| DateAndTime as tsTransportStreamBitRateLatestError | |||
| ActiveTime as tsTransportStreamBitRateActiveTime | |||
| MeasurementState as tsTransportStreamBitRateMeasurementState | |||
| FloatingPoint as tsTransportStreamBitRateValue | |||
| DisplayString as tsTransportStreamBitRateNomenclature | |||
| TsServiceBitRateEntry | |||
| SEQUENCE | |||
| InputNumber as tsServiceBitRateInputNumber | |||
| ServiceId as tsServiceBitRateService | |||
| RowStatus as tsServiceBitRateRowStatus | |||
| TestState as tsServiceBitRateState | |||
| Enable as tsServiceBitRateEnable | |||
| Counter32 as tsServiceBitRateCounter | |||
| DateAndTime as tsServiceBitRateCounterDiscontinuity | |||
| TruthValue as tsServiceBitRateCounterReset | |||
| DateAndTime as tsServiceBitRateLatestError | |||
| ActiveTime as tsServiceBitRateActiveTime | |||
| MeasurementState as tsServiceBitRateMeasurementState | |||
| FloatingPoint as tsServiceBitRateValue | |||
| DisplayString as tsServiceBitRateNomenclature | |||
| TsPIDBitRateEntry | |||
| SEQUENCE | |||
| InputNumber as tsPIDBitRateInputNumber | |||
| PIDPlusOne as tsPIDBitRatePID | |||
| RowStatus as tsPIDBitRateRowStatus | |||
| TestState as tsPIDBitRateState | |||
| Enable as tsPIDBitRateEnable | |||
| Counter32 as tsPIDBitRateCounter | |||
| DateAndTime as tsPIDBitRateCounterDiscontinuity | |||
| TruthValue as tsPIDBitRateCounterReset | |||
| DateAndTime as tsPIDBitRateLatestError | |||
| ActiveTime as tsPIDBitRateActiveTime | |||
| MeasurementState as tsPIDBitRateMeasurementState | |||
| FloatingPoint as tsPIDBitRateValue | |||
| DisplayString as tsPIDBitRateNomenclature | |||
| TsConsistencyEntry | |||
| SEQUENCE | |||
| InputNumber as tsConsistencyInputNumber | |||
| IndexConsistencyTest as tsConsistencyTestNumber | |||
| TestState as tsConsistencyState | |||
| Enable as tsConsistencyEnable | |||
| Counter32 as tsConsistencyCounter | |||
| DateAndTime as tsConsistencyCounterDiscontinuity | |||
| TruthValue as tsConsistencyCounterReset | |||
| DateAndTime as tsConsistencyLatestError | |||
| ActiveTime as tsConsistencyActiveTime | |||
| TsMeasurePreferencesEntry | |||
| SEQUENCE | |||
| InputNumber as tsMeasurePrefInputNumber | |||
| FloatingPoint as tsMeasurePrefPCRDemarcationFrequency | |||
| FloatingPoint as tsMeasurePrefPCRFOMax | |||
| FloatingPoint as tsMeasurePrefPCRDRMax | |||
| FloatingPoint as tsMeasurePrefPCROJMax | |||
| FloatingPoint as tsMeasurePrefTSBitRateTau | |||
| Unsigned32 as tsMeasurePrefTSBitRateN | |||
| BitRateElement as tsMeasurePrefTSBitRateElement | |||
| FloatingPoint as tsMeasurePrefTSBitRateMin | |||
| FloatingPoint as tsMeasurePrefTSBitRateMax | |||
| FloatingPoint as tsMeasurePrefAllServiceBitRateTau | |||
| Unsigned32 as tsMeasurePrefAllServiceBitRateN | |||
| BitRateElement as tsMeasurePrefAllServiceBitRateElement | |||
| FloatingPoint as tsMeasurePrefAllPIDBitRateTau | |||
| Unsigned32 as tsMeasurePrefAllPIDBitRateN | |||
| BitRateElement as tsMeasurePrefAllPIDBitRateElement | |||
| TransportStreamID as tsMeasurePrefExpectedTSID | |||
| TsMeasurePreferencesServiceEntry | |||
| SEQUENCE | |||
| InputNumber as tsMeasurePrefServiceInputNumber | |||
| ServiceId as tsMeasurePrefServiceService | |||
| RowStatus as tsMeasurePrefServiceRowStatus | |||
| FloatingPoint as tsMeasurePrefServiceBitRateTau | |||
| Unsigned32 as tsMeasurePrefServiceBitRateN | |||
| BitRateElement as tsMeasurePrefServiceBitRateElement | |||
| FloatingPoint as tsMeasurePrefServiceBitRateMin | |||
| FloatingPoint as tsMeasurePrefServiceBitRateMax | |||
| TsMeasurePreferencesPIDEntry | |||
| SEQUENCE | |||
| InputNumber as tsMeasurePrefPIDInputNumber | |||
| PIDPlusOne as tsMeasurePrefPIDPID | |||
| RowStatus as tsMeasurePrefPIDRowStatus | |||
| FloatingPoint as tsMeasurePrefPIDBitRateTau | |||
| Unsigned32 as tsMeasurePrefPIDBitRateN | |||
| BitRateElement as tsMeasurePrefPIDBitRateElement | |||
| FloatingPoint as tsMeasurePrefPIDBitRateMin | |||
| FloatingPoint as tsMeasurePrefPIDBitRateMax | |||
| TsServicePerformanceEntry | |||
| SEQUENCE | |||
| InputNumber as tsServicePerformanceInputNumber | |||
| IndexServicePerformance as tsServicePerformanceNumber | |||
| TestState as tsServicePerformanceState | |||
| Enable as tsServicePerformanceEnable | |||
| Counter32 as tsServicePerformanceCounter | |||
| DateAndTime as tsServicePerformanceCounterDiscontinuity | |||
| TruthValue as tsServicePerformanceCounterReset | |||
| DateAndTime as tsServicePerformanceLatestError | |||
| ActiveTime as tsServicePerformanceActiveTime | |||
| MeasurementState as tsServicePerformanceMeasurementState | |||
| Unsigned32 as tsServicePerformanceError | |||
| FloatingPoint as tsServicePerformanceErrorRatio | |||
| TsServicePerformancePreferencesEntry | |||
| SEQUENCE | |||
| InputNumber as tsSPPrefInputNumber | |||
| IndexServicePerformance as tsSPPrefNumber | |||
| FloatingPoint as tsSPPrefDeltaT | |||
| FloatingPoint as tsSPPrefEvaluationTime | |||
| FloatingPoint as tsSPPrefThreshold | |||
| SysAvailabilityEntry | |||
| SEQUENCE | |||
| InputNumber as sysAvailabilityInputNumber | |||
| TestState as sysAvailabilityTestState | |||
| Enable as sysAvailabilityEnable | |||
| Counter32 as sysAvailabilityCounter | |||
| DateAndTime as sysAvailabilityCounterDiscontinuity | |||
| TruthValue as sysAvailabilityCounterReset | |||
| DateAndTime as sysAvailabilityLatestError | |||
| ActiveTime as sysAvailabilityActiveTime | |||
| MeasurementState as sysAvailabilityMeasurementState | |||
| Unsigned32 as sysAvailabilityUnavailableTime | |||
| FloatingPoint as sysAvailabilityRatio | |||
| TruthValue as sysAvailabilityInSETI | |||
| LinkAvailabilityEntry | |||
| SEQUENCE | |||
| InputNumber as linkAvailabilityInputNumber | |||
| TestState as linkAvailabilityTestState | |||
| Enable as linkAvailabilityEnable | |||
| Counter32 as linkAvailabilityCounter | |||
| DateAndTime as linkAvailabilityCounterDiscontinuity | |||
| TruthValue as linkAvailabilityCounterReset | |||
| DateAndTime as linkAvailabilityLatestError | |||
| ActiveTime as linkAvailabilityActiveTime | |||
| MeasurementState as linkAvailabilityMeasurementState | |||
| Unsigned32 as linkAvailabilityUnavailableTime | |||
| FloatingPoint as linkAvailabilityRatio | |||
| TruthValue as linkAvailabilityInSUTI | |||
| BerRSinServiceEntry | |||
| SEQUENCE | |||
| InputNumber as berRSinServiceInputNumber | |||
| TestState as berRSinServiceTestState | |||
| Enable as berRSinServiceEnable | |||
| Counter32 as berRSinServiceCounter | |||
| DateAndTime as berRSinServiceCounterDiscontinuity | |||
| TruthValue as berRSinServiceCounterReset | |||
| DateAndTime as berRSinServiceLatestError | |||
| ActiveTime as berRSinServiceActiveTime | |||
| MeasurementState as berRSinServiceMeasurementState | |||
| FloatingPoint as berRSinServiceValue | |||
| RfIFsignalPowerEntry | |||
| SEQUENCE | |||
| InputNumber as rfIFsignalPowerInputNumber | |||
| TestState as rfIFsignalPowerTestState | |||
| Enable as rfIFsignalPowerEnable | |||
| Counter32 as rfIFsignalPowerCounter | |||
| DateAndTime as rfIFsignalPowerCounterDiscontinuity | |||
| TruthValue as rfIFsignalPowerCounterReset | |||
| DateAndTime as rfIFsignalPowerLatestError | |||
| ActiveTime as rfIFsignalPowerActiveTime | |||
| MeasurementState as rfIFsignalPowerMeasurementState | |||
| FloatingPoint as rfIFsignalPowerValue | |||
| NoisePowerEntry | |||
| SEQUENCE | |||
| InputNumber as noisePowerInputNumber | |||
| TestState as noisePowerTestState | |||
| Enable as noisePowerEnable | |||
| Counter32 as noisePowerCounter | |||
| DateAndTime as noisePowerCounterDiscontinuity | |||
| TruthValue as noisePowerCounterReset | |||
| DateAndTime as noisePowerLatestError | |||
| ActiveTime as noisePowerActiveTime | |||
| MeasurementState as noisePowerMeasurementState | |||
| FloatingPoint as noisePowerValue | |||
| MerCSEntry | |||
| SEQUENCE | |||
| InputNumber as merCSInputNumber | |||
| TestState as merCSTestState | |||
| Enable as merCSEnable | |||
| Counter32 as merCSCounter | |||
| DateAndTime as merCSCounterDiscontinuity | |||
| TruthValue as merCSCounterReset | |||
| DateAndTime as merCSLatestError | |||
| ActiveTime as merCSActiveTime | |||
| MeasurementState as merCSMeasurementState | |||
| FloatingPoint as merCSValue | |||
| SteMeanCSEntry | |||
| SEQUENCE | |||
| InputNumber as steMeanCSInputNumber | |||
| TestState as steMeanCSTestState | |||
| Enable as steMeanCSEnable | |||
| Counter32 as steMeanCSCounter | |||
| DateAndTime as steMeanCSCounterDiscontinuity | |||
| TruthValue as steMeanCSCounterReset | |||
| DateAndTime as steMeanCSLatestError | |||
| ActiveTime as steMeanCSActiveTime | |||
| MeasurementState as steMeanCSMeasurementState | |||
| FloatingPoint as steMeanCSValue | |||
| SteDeviationCSEntry | |||
| SEQUENCE | |||
| InputNumber as steDeviationCSInputNumber | |||
| TestState as steDeviationCSTestState | |||
| Enable as steDeviationCSEnable | |||
| Counter32 as steDeviationCSCounter | |||
| DateAndTime as steDeviationCSCounterDiscontinuity | |||
| TruthValue as steDeviationCSCounterReset | |||
| DateAndTime as steDeviationCSLatestError | |||
| ActiveTime as steDeviationCSActiveTime | |||
| MeasurementState as steDeviationCSMeasurementState | |||
| FloatingPoint as steDeviationCSValue | |||
| CsCSEntry | |||
| SEQUENCE | |||
| InputNumber as csCSInputNumber | |||
| TestState as csCSTestState | |||
| Enable as csCSEnable | |||
| Counter32 as csCSCounter | |||
| DateAndTime as csCSCounterDiscontinuity | |||
| TruthValue as csCSCounterReset | |||
| DateAndTime as csCSLatestError | |||
| ActiveTime as csCSActiveTime | |||
| MeasurementState as csCSMeasurementState | |||
| FloatingPoint as csCSValue | |||
| AiCSEntry | |||
| SEQUENCE | |||
| InputNumber as aiCSInputNumber | |||
| TestState as aiCSTestState | |||
| Enable as aiCSEnable | |||
| Counter32 as aiCSCounter | |||
| DateAndTime as aiCSCounterDiscontinuity | |||
| TruthValue as aiCSCounterReset | |||
| DateAndTime as aiCSLatestError | |||
| ActiveTime as aiCSActiveTime | |||
| MeasurementState as aiCSMeasurementState | |||
| FloatingPoint as aiCSValue | |||
| QeCSEntry | |||
| SEQUENCE | |||
| InputNumber as qeCSInputNumber | |||
| TestState as qeCSTestState | |||
| Enable as qeCSEnable | |||
| Counter32 as qeCSCounter | |||
| DateAndTime as qeCSCounterDiscontinuity | |||
| TruthValue as qeCSCounterReset | |||
| DateAndTime as qeCSLatestError | |||
| ActiveTime as qeCSActiveTime | |||
| MeasurementState as qeCSMeasurementState | |||
| FloatingPoint as qeCSValue | |||
| RteCSEntry | |||
| SEQUENCE | |||
| InputNumber as rteCSInputNumber | |||
| TestState as rteCSTestState | |||
| Enable as rteCSEnable | |||
| Counter32 as rteCSCounter | |||
| DateAndTime as rteCSCounterDiscontinuity | |||
| TruthValue as rteCSCounterReset | |||
| DateAndTime as rteCSLatestError | |||
| ActiveTime as rteCSActiveTime | |||
| MeasurementState as rteCSMeasurementState | |||
| FloatingPoint as rteCSValue | |||
| CiCSEntry | |||
| SEQUENCE | |||
| InputNumber as ciCSInputNumber | |||
| TestState as ciCSTestState | |||
| Enable as ciCSEnable | |||
| Counter32 as ciCSCounter | |||
| DateAndTime as ciCSCounterDiscontinuity | |||
| TruthValue as ciCSCounterReset | |||
| DateAndTime as ciCSLatestError | |||
| ActiveTime as ciCSActiveTime | |||
| MeasurementState as ciCSMeasurementState | |||
| FloatingPoint as ciCSValue | |||
| PjCSEntry | |||
| SEQUENCE | |||
| InputNumber as pjCSInputNumber | |||
| TestState as pjCSTestState | |||
| Enable as pjCSEnable | |||
| Counter32 as pjCSCounter | |||
| DateAndTime as pjCSCounterDiscontinuity | |||
| TruthValue as pjCSCounterReset | |||
| DateAndTime as pjCSLatestError | |||
| ActiveTime as pjCSActiveTime | |||
| MeasurementState as pjCSMeasurementState | |||
| FloatingPoint as pjCSValue | |||
| SnrCSEntry | |||
| SEQUENCE | |||
| InputNumber as snrCSInputNumber | |||
| TestState as snrCSTestState | |||
| Enable as snrCSEnable | |||
| Counter32 as snrCSCounter | |||
| DateAndTime as snrCSCounterDiscontinuity | |||
| TruthValue as snrCSCounterReset | |||
| DateAndTime as snrCSLatestError | |||
| ActiveTime as snrCSActiveTime | |||
| MeasurementState as snrCSMeasurementState | |||
| FloatingPoint as snrCSValue | |||
| CableSatPreferencesEntry | |||
| SEQUENCE | |||
| InputNumber as cableSatPrefInputNumber | |||
| FloatingPoint as cableSatPrefCentreFrequency | |||
| Modulation as cableSatPrefModulation | |||
| UATMode as cableSatPrefSysAvailUATMode | |||
| Unsigned32 as cableSatPrefSysAvailN | |||
| FloatingPoint as cableSatPrefSysAvailT | |||
| Unsigned32 as cableSatPrefSysAvailM | |||
| FloatingPoint as cableSatPrefSysAvailTI | |||
| FloatingPoint as cableSatPrefSysAvailEBPerCent | |||
| FloatingPoint as cableSatPrefSysAvailTotalTime | |||
| UATMode as cableSatPrefLinkAvailUATMode | |||
| Unsigned32 as cableSatPrefLinkAvailN | |||
| FloatingPoint as cableSatPrefLinkAvailT | |||
| Unsigned32 as cableSatPrefLinkAvailM | |||
| FloatingPoint as cableSatPrefLinkAvailTI | |||
| FloatingPoint as cableSatPrefLinkAvailUPPerCent | |||
| FloatingPoint as cableSatPrefLinkAvailTotalTime | |||
| FloatingPoint as cableSatPrefBERMax | |||
| FloatingPoint as cableSatPrefSignalPowerMin | |||
| FloatingPoint as cableSatPrefSignalPowerMax | |||
| FloatingPoint as cableSatPrefNoisePowerMax | |||
| FloatingPoint as cableSatPrefMerCSMin | |||
| FloatingPoint as cableSatPrefSteMeanCSMax | |||
| FloatingPoint as cableSatPrefSteDeviationCSMax | |||
| FloatingPoint as cableSatPrefCsCSMin | |||
| FloatingPoint as cableSatPrefAiCSMax | |||
| FloatingPoint as cableSatPrefQeCSMax | |||
| FloatingPoint as cableSatPrefRteCSMax | |||
| FloatingPoint as cableSatPrefCiCSMin | |||
| FloatingPoint as cableSatPrefPjCSMax | |||
| FloatingPoint as cableSatPrefSnrCSMin | |||
| NoiseMarginEntry | |||
| SEQUENCE | |||
| InputNumber as noiseMarginInputNumber | |||
| TestState as noiseMarginTestState | |||
| Enable as noiseMarginEnable | |||
| Counter32 as noiseMarginCounter | |||
| DateAndTime as noiseMarginCounterDiscontinuity | |||
| TruthValue as noiseMarginCounterReset | |||
| DateAndTime as noiseMarginLatestError | |||
| ActiveTime as noiseMarginActiveTime | |||
| MeasurementState as noiseMarginMeasurementState | |||
| FloatingPoint as noiseMarginValue | |||
| EstNoiseMarginEntry | |||
| SEQUENCE | |||
| InputNumber as estNoiseMarginInputNumber | |||
| TestState as estNoiseMarginTestState | |||
| Enable as estNoiseMarginEnable | |||
| Counter32 as estNoiseMarginCounter | |||
| DateAndTime as estNoiseMarginCounterDiscontinuity | |||
| TruthValue as estNoiseMarginCounterReset | |||
| DateAndTime as estNoiseMarginLatestError | |||
| ActiveTime as estNoiseMarginActiveTime | |||
| MeasurementState as estNoiseMarginMeasurementState | |||
| FloatingPoint as estNoiseMarginValue | |||
| SignQualMarTEntry | |||
| SEQUENCE | |||
| InputNumber as signQualMarTInputNumber | |||
| TestState as signQualMarTTestState | |||
| Enable as signQualMarTEnable | |||
| Counter32 as signQualMarTCounter | |||
| DateAndTime as signQualMarTCounterDiscontinuity | |||
| TruthValue as signQualMarTCounterReset | |||
| DateAndTime as signQualMarTLatestError | |||
| ActiveTime as signQualMarTActiveTime | |||
| ENDCEntry | |||
| SEQUENCE | |||
| InputNumber as eNDCInputNumber | |||
| TestState as eNDCTestState | |||
| Enable as eNDCEnable | |||
| Counter32 as eNDCCounter | |||
| DateAndTime as eNDCCounterDiscontinuity | |||
| TruthValue as eNDCCounterReset | |||
| DateAndTime as eNDCLatestError | |||
| ActiveTime as eNDCActiveTime | |||
| MeasurementState as eNDCMeasurementState | |||
| FloatingPoint as eNDCValue | |||
| OutBandEmissEntry | |||
| SEQUENCE | |||
| InputNumber as outBandEmissInputNumber | |||
| TestState as outBandEmissTestState | |||
| Enable as outBandEmissEnable | |||
| Counter32 as outBandEmissCounter | |||
| DateAndTime as outBandEmissCounterDiscontinuity | |||
| TruthValue as outBandEmissCounterReset | |||
| DateAndTime as outBandEmissLatestError | |||
| ActiveTime as outBandEmissActiveTime | |||
| CablePreferencesEntry | |||
| SEQUENCE | |||
| InputNumber as cablePrefInputNumber | |||
| FloatingPoint as cablePrefNoiseMarginMin | |||
| FloatingPoint as cablePrefEstNoiseMarginMin | |||
| FloatingPoint as cablePrefSignQualBoxSize | |||
| Integer32 as cablePrefSignQualPercentMax | |||
| FloatingPoint as cablePrefENDBER | |||
| TruthValue as cablePrefENDCtoNSpecified | |||
| FloatingPoint as cablePrefENDIdeal | |||
| FloatingPoint as cablePrefENDMax | |||
| BerViterbiSEntry | |||
| SEQUENCE | |||
| InputNumber as berViterbiSInputNumber | |||
| TestState as berViterbiSTestState | |||
| Enable as berViterbiSEnable | |||
| Counter32 as berViterbiSCounter | |||
| DateAndTime as berViterbiSCounterDiscontinuity | |||
| TruthValue as berViterbiSCounterReset | |||
| DateAndTime as berViterbiSLatestError | |||
| ActiveTime as berViterbiSActiveTime | |||
| MeasurementState as berViterbiSMeasurementState | |||
| FloatingPoint as berViterbiSIValue | |||
| FloatingPoint as berViterbiSQValue | |||
| BERMeasurementMethod as berViterbiSMeasurementMethod | |||
| IfSpectrumEntry | |||
| SEQUENCE | |||
| InputNumber as ifSpectrumInputNumber | |||
| TestState as ifSpectrumTestState | |||
| Enable as ifSpectrumEnable | |||
| Counter32 as ifSpectrumCounter | |||
| DateAndTime as ifSpectrumCounterDiscontinuity | |||
| TruthValue as ifSpectrumCounterReset | |||
| DateAndTime as ifSpectrumLatestError | |||
| ActiveTime as ifSpectrumActiveTime | |||
| SatellitePreferencesEntry | |||
| SEQUENCE | |||
| InputNumber as satellitePrefInputNumber | |||
| FloatingPoint as satellitePrefBERMax | |||
| RfAccuracyEntry | |||
| SEQUENCE | |||
| InputNumber as rfAccuracyInputNumber | |||
| TestState as rfAccuracyTestState | |||
| Enable as rfAccuracyEnable | |||
| Counter32 as rfAccuracyCounter | |||
| DateAndTime as rfAccuracyCounterDiscontinuity | |||
| TruthValue as rfAccuracyCounterReset | |||
| DateAndTime as rfAccuracyLatestError | |||
| ActiveTime as rfAccuracyActiveTime | |||
| MeasurementState as rfAccuracyMeasurementState | |||
| FloatingPoint as rfAccuracyValue | |||
| RfChannelWidthEntry | |||
| SEQUENCE | |||
| InputNumber as rfChannelWidthInputNumber | |||
| TestState as rfChannelWidthTestState | |||
| Enable as rfChannelWidthEnable | |||
| Counter32 as rfChannelWidthCounter | |||
| DateAndTime as rfChannelWidthCounterDiscontinuity | |||
| TruthValue as rfChannelWidthCounterReset | |||
| DateAndTime as rfChannelWidthLatestError | |||
| ActiveTime as rfChannelWidthActiveTime | |||
| MeasurementState as rfChannelWidthMeasurementState | |||
| FloatingPoint as rfChannelWidthValue | |||
| SymbolLengthEntry | |||
| SEQUENCE | |||
| InputNumber as symbolLengthInputNumber | |||
| TestState as symbolLengthTestState | |||
| Enable as symbolLengthEnable | |||
| Counter32 as symbolLengthCounter | |||
| DateAndTime as symbolLengthCounterDiscontinuity | |||
| TruthValue as symbolLengthCounterReset | |||
| DateAndTime as symbolLengthLatestError | |||
| ActiveTime as symbolLengthActiveTime | |||
| MeasurementState as symbolLengthMeasurementState | |||
| FloatingPoint as symbolLengthValue | |||
| RfIfPowerEntry | |||
| SEQUENCE | |||
| InputNumber as rfIfPowerInputNumber | |||
| TestState as rfIfPowerTestState | |||
| Enable as rfIfPowerEnable | |||
| Counter32 as rfIfPowerCounter | |||
| DateAndTime as rfIfPowerCounterDiscontinuity | |||
| TruthValue as rfIfPowerCounterReset | |||
| DateAndTime as rfIfPowerLatestError | |||
| ActiveTime as rfIfPowerActiveTime | |||
| MeasurementState as rfIfPowerMeasurementState | |||
| FloatingPoint as rfIfPowerValue | |||
| RfIfSpectrumEntry | |||
| SEQUENCE | |||
| InputNumber as rfIfSpectrumInputNumber | |||
| TestState as rfIfSpectrumTestState | |||
| Enable as rfIfSpectrumEnable | |||
| Counter32 as rfIfSpectrumCounter | |||
| DateAndTime as rfIfSpectrumCounterDiscontinuity | |||
| TruthValue as rfIfSpectrumCounterReset | |||
| DateAndTime as rfIfSpectrumLatestError | |||
| ActiveTime as rfIfSpectrumActiveTime | |||
| ENDTEntry | |||
| SEQUENCE | |||
| InputNumber as eNDTInputNumber | |||
| TestState as eNDTTestState | |||
| Enable as eNDTEnable | |||
| Counter32 as eNDTCounter | |||
| DateAndTime as eNDTCounterDiscontinuity | |||
| TruthValue as eNDTCounterReset | |||
| DateAndTime as eNDTLatestError | |||
| ActiveTime as eNDTActiveTime | |||
| MeasurementState as eNDTMeasurementState | |||
| FloatingPoint as eNDTValue | |||
| ENFTEntry | |||
| SEQUENCE | |||
| InputNumber as eNFTInputNumber | |||
| TestState as eNFTTestState | |||
| Enable as eNFTEnable | |||
| Counter32 as eNFTCounter | |||
| DateAndTime as eNFTCounterDiscontinuity | |||
| TruthValue as eNFTCounterReset | |||
| DateAndTime as eNFTLatestError | |||
| ActiveTime as eNFTActiveTime | |||
| MeasurementState as eNFTMeasurementState | |||
| FloatingPoint as eNFTValue | |||
| ENDTLPEntry | |||
| SEQUENCE | |||
| InputNumber as eNDTLPInputNumber | |||
| TestState as eNDTLPTestState | |||
| Enable as eNDTLPEnable | |||
| Counter32 as eNDTLPCounter | |||
| DateAndTime as eNDTLPCounterDiscontinuity | |||
| TruthValue as eNDTLPCounterReset | |||
| DateAndTime as eNDTLPLatestError | |||
| ActiveTime as eNDTLPActiveTime | |||
| MeasurementState as eNDTLPMeasurementState | |||
| FloatingPoint as eNDTLPValue | |||
| ENFTLPEntry | |||
| SEQUENCE | |||
| InputNumber as eNFTLPInputNumber | |||
| TestState as eNFTLPTestState | |||
| Enable as eNFTLPEnable | |||
| Counter32 as eNFTLPCounter | |||
| DateAndTime as eNFTLPCounterDiscontinuity | |||
| TruthValue as eNFTLPCounterReset | |||
| DateAndTime as eNFTLPLatestError | |||
| ActiveTime as eNFTLPActiveTime | |||
| MeasurementState as eNFTLPMeasurementState | |||
| FloatingPoint as eNFTLPValue | |||
| LinearityEntry | |||
| SEQUENCE | |||
| InputNumber as linearityInputNumber | |||
| TestState as linearityTestState | |||
| Enable as linearityEnable | |||
| Counter32 as linearityCounter | |||
| DateAndTime as linearityCounterDiscontinuity | |||
| TruthValue as linearityCounterReset | |||
| DateAndTime as linearityLatestError | |||
| ActiveTime as linearityActiveTime | |||
| MeasurementState as linearityMeasurementState | |||
| FloatingPoint as linearityValue | |||
| BerViterbiTEntry | |||
| SEQUENCE | |||
| InputNumber as berViterbiTInputNumber | |||
| TestState as berViterbiTTestState | |||
| Enable as berViterbiTEnable | |||
| Counter32 as berViterbiTCounter | |||
| DateAndTime as berViterbiTCounterDiscontinuity | |||
| TruthValue as berViterbiTCounterReset | |||
| DateAndTime as berViterbiTLatestError | |||
| ActiveTime as berViterbiTActiveTime | |||
| MeasurementState as berViterbiTMeasurementState | |||
| FloatingPoint as berViterbiTValue | |||
| BerViterbiTLPEntry | |||
| SEQUENCE | |||
| InputNumber as berViterbiTLPInputNumber | |||
| TestState as berViterbiTLPTestState | |||
| Enable as berViterbiTLPEnable | |||
| Counter32 as berViterbiTLPCounter | |||
| DateAndTime as berViterbiTLPCounterDiscontinuity | |||
| TruthValue as berViterbiTLPCounterReset | |||
| DateAndTime as berViterbiTLPLatestError | |||
| ActiveTime as berViterbiTLPActiveTime | |||
| MeasurementState as berViterbiTLPMeasurementState | |||
| FloatingPoint as berViterbiTLPValue | |||
| BerRSEntry | |||
| SEQUENCE | |||
| InputNumber as berRSInputNumber | |||
| TestState as berRSTestState | |||
| Enable as berRSEnable | |||
| Counter32 as berRSCounter | |||
| DateAndTime as berRSCounterDiscontinuity | |||
| TruthValue as berRSCounterReset | |||
| DateAndTime as berRSLatestError | |||
| ActiveTime as berRSActiveTime | |||
| MeasurementState as berRSMeasurementState | |||
| FloatingPoint as berRSValue | |||
| BerRSLPEntry | |||
| SEQUENCE | |||
| InputNumber as berRSLPInputNumber | |||
| TestState as berRSLPTestState | |||
| Enable as berRSLPEnable | |||
| Counter32 as berRSLPCounter | |||
| DateAndTime as berRSLPCounterDiscontinuity | |||
| TruthValue as berRSLPCounterReset | |||
| DateAndTime as berRSLPLatestError | |||
| ActiveTime as berRSLPActiveTime | |||
| MeasurementState as berRSLPMeasurementState | |||
| FloatingPoint as berRSLPValue | |||
| MerTEntry | |||
| SEQUENCE | |||
| InputNumber as merTInputNumber | |||
| TestState as merTTestState | |||
| Enable as merTEnable | |||
| Counter32 as merTCounter | |||
| DateAndTime as merTCounterDiscontinuity | |||
| TruthValue as merTCounterReset | |||
| DateAndTime as merTLatestError | |||
| ActiveTime as merTActiveTime | |||
| MeasurementState as merTMeasurementState | |||
| FloatingPoint as merTValue | |||
| SteMeanTEntry | |||
| SEQUENCE | |||
| InputNumber as steMeanTInputNumber | |||
| TestState as steMeanTTestState | |||
| Enable as steMeanTEnable | |||
| Counter32 as steMeanTCounter | |||
| DateAndTime as steMeanTCounterDiscontinuity | |||
| TruthValue as steMeanTCounterReset | |||
| DateAndTime as steMeanTLatestError | |||
| ActiveTime as steMeanTActiveTime | |||
| MeasurementState as steMeanTMeasurementState | |||
| FloatingPoint as steMeanTValue | |||
| SteDeviationTEntry | |||
| SEQUENCE | |||
| InputNumber as steDeviationTInputNumber | |||
| TestState as steDeviationTTestState | |||
| Enable as steDeviationTEnable | |||
| Counter32 as steDeviationTCounter | |||
| DateAndTime as steDeviationTCounterDiscontinuity | |||
| TruthValue as steDeviationTCounterReset | |||
| DateAndTime as steDeviationTLatestError | |||
| ActiveTime as steDeviationTActiveTime | |||
| MeasurementState as steDeviationTMeasurementState | |||
| FloatingPoint as steDeviationTValue | |||
| CsTEntry | |||
| SEQUENCE | |||
| InputNumber as csTInputNumber | |||
| TestState as csTTestState | |||
| Enable as csTEnable | |||
| Counter32 as csTCounter | |||
| DateAndTime as csTCounterDiscontinuity | |||
| TruthValue as csTCounterReset | |||
| DateAndTime as csTLatestError | |||
| ActiveTime as csTActiveTime | |||
| MeasurementState as csTMeasurementState | |||
| FloatingPoint as csTValue | |||
| AiTEntry | |||
| SEQUENCE | |||
| InputNumber as aiTInputNumber | |||
| TestState as aiTTestState | |||
| Enable as aiTEnable | |||
| Counter32 as aiTCounter | |||
| DateAndTime as aiTCounterDiscontinuity | |||
| TruthValue as aiTCounterReset | |||
| DateAndTime as aiTLatestError | |||
| ActiveTime as aiTActiveTime | |||
| MeasurementState as aiTMeasurementState | |||
| FloatingPoint as aiTValue | |||
| QeTEntry | |||
| SEQUENCE | |||
| InputNumber as qeTInputNumber | |||
| TestState as qeTTestState | |||
| Enable as qeTEnable | |||
| Counter32 as qeTCounter | |||
| DateAndTime as qeTCounterDiscontinuity | |||
| TruthValue as qeTCounterReset | |||
| DateAndTime as qeTLatestError | |||
| ActiveTime as qeTActiveTime | |||
| MeasurementState as qeTMeasurementState | |||
| FloatingPoint as qeTValue | |||
| PjTEntry | |||
| SEQUENCE | |||
| InputNumber as pjTInputNumber | |||
| TestState as pjTTestState | |||
| Enable as pjTEnable | |||
| Counter32 as pjTCounter | |||
| DateAndTime as pjTCounterDiscontinuity | |||
| TruthValue as pjTCounterReset | |||
| DateAndTime as pjTLatestError | |||
| ActiveTime as pjTActiveTime | |||
| MeasurementState as pjTMeasurementState | |||
| FloatingPoint as pjTValue | |||
| MipSyntaxEntry | |||
| SEQUENCE | |||
| InputNumber as mipSyntaxInputNumber | |||
| IndexMIPSyntaxTest as mipSyntaxTestNumber | |||
| TestState as mipSyntaxState | |||
| Enable as mipSyntaxEnable | |||
| Counter32 as mipSyntaxCounter | |||
| DateAndTime as mipSyntaxCounterDiscontinuity | |||
| TruthValue as mipSyntaxCounterReset | |||
| DateAndTime as mipSyntaxLatestError | |||
| ActiveTime as mipSyntaxActiveTime | |||
| SepEtiEntry | |||
| SEQUENCE | |||
| InputNumber as sepEtiInputNumber | |||
| TestState as sepEtiTestState | |||
| Enable as sepEtiEnable | |||
| Counter32 as sepEtiCounter | |||
| DateAndTime as sepEtiCounterDiscontinuity | |||
| TruthValue as sepEtiCounterReset | |||
| DateAndTime as sepEtiLatestError | |||
| ActiveTime as sepEtiActiveTime | |||
| MeasurementState as sepEtiMeasurementState | |||
| FloatingPoint as sepEtiValue | |||
| SepSetiEntry | |||
| SEQUENCE | |||
| InputNumber as sepSetiInputNumber | |||
| TestState as sepSetiTestState | |||
| Enable as sepSetiEnable | |||
| Counter32 as sepSetiCounter | |||
| DateAndTime as sepSetiCounterDiscontinuity | |||
| TruthValue as sepSetiCounterReset | |||
| DateAndTime as sepSetiLatestError | |||
| ActiveTime as sepSetiActiveTime | |||
| MeasurementState as sepSetiMeasurementState | |||
| FloatingPoint as sepSetiValue | |||
| TerrestrialPreferencesEntry | |||
| SEQUENCE | |||
| InputNumber as terrestrialPrefInputNumber | |||
| FloatingPoint as terrestrialPrefCentreFrequency | |||
| FloatingPoint as terrestrialPrefBandwidth | |||
| Modulation as terrestrialPrefModulation | |||
| TerrestrialTransmissionMode as terrestrialPrefTransmissionMode | |||
| GuardInterval as terrestrialPrefGuardInterval | |||
| Hierarchy as terrestrialPrefHierarchical | |||
| FloatingPoint as terrestrialPrefCentreFreqExpected | |||
| FloatingPoint as terrestrialPrefCentreFreqLimit | |||
| FloatingPoint as terrestrialPrefChannelWidthLimit | |||
| FloatingPoint as terrestrialPrefSymbolLengthLimit | |||
| FloatingPoint as terrestrialPrefPowerMin | |||
| FloatingPoint as terrestrialPrefPowerMax | |||
| FloatingPoint as terrestrialPrefENDBER | |||
| FloatingPoint as terrestrialPrefENDIdeal | |||
| FloatingPoint as terrestrialPrefENDMax | |||
| FloatingPoint as terrestrialPrefENFIdeal | |||
| FloatingPoint as terrestrialPrefENFMax | |||
| FloatingPoint as terrestrialPrefENDLPIdeal | |||
| FloatingPoint as terrestrialPrefENDLPMax | |||
| FloatingPoint as terrestrialPrefENFLPIdeal | |||
| FloatingPoint as terrestrialPrefENFLPMax | |||
| FloatingPoint as terrestrialPrefLinearityMin | |||
| FloatingPoint as terrestrialPrefBERViterbiMax | |||
| FloatingPoint as terrestrialPrefBERViterbiLPMax | |||
| FloatingPoint as terrestrialPrefBERRSMax | |||
| FloatingPoint as terrestrialPrefBERRSLPMax | |||
| FloatingPoint as terrestrialPrefMerTMin | |||
| FloatingPoint as terrestrialPrefSteMeanMax | |||
| FloatingPoint as terrestrialPrefSteDeviationMax | |||
| FloatingPoint as terrestrialPrefCsMin | |||
| FloatingPoint as terrestrialPrefAiMax | |||
| FloatingPoint as terrestrialPrefQeMax | |||
| FloatingPoint as terrestrialPrefPjMax | |||
| FloatingPoint as terrestrialPrefMIPTimingLimit | |||
| FloatingPoint as terrestrialPrefMIPDeviationMax | |||
| UATMode as terrestrialPrefSEPUATMode | |||
| Unsigned32 as terrestrialPrefSEPN | |||
| FloatingPoint as terrestrialPrefSEPT | |||
| Unsigned32 as terrestrialPrefSEPM | |||
| FloatingPoint as terrestrialPrefSEPTI | |||
| FloatingPoint as terrestrialPrefSEPEBPerCent | |||
| FloatingPoint as terrestrialPrefSEPMeasurementInterval | |||