
| SNMPv2-SMI | SNMPv2-TC | RFC1213-MIB |
| EXTREME-BASE-MIB |
| MODULE-IDENTITY | OBJECT-TYPE | Unsigned32 |
| TruthValue | DisplayString | IpAddress |
| extremeAgent | PortList |
| extremePOSMib | 1.3.6.1.4.1.1916.1.20 | ||
| Extreme POS objects: objects common to POS MIBs | |||
| MODULE-IDENTITY | |||
| extremeAps | 1.3.6.1.4.1.1916.1.20.1 | ||
| OBJECT IDENTIFIER | |||
| extremeApsConfig | 1.3.6.1.4.1.1916.1.20.1.1 | ||
| OBJECT IDENTIFIER | |||
| extremeApsConfigEnabled | 1.3.6.1.4.1.1916.1.20.1.1.1 | ||
| Global APS enablement | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| extremeApsGroupConfigTable | 1.3.6.1.4.1.1916.1.20.1.1.2 | ||
| This table contains configuration information by defined APS group. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ExtremeApsGroupConfigEntry | |||
| extremeApsGroupConfigEntry | 1.3.6.1.4.1.1916.1.20.1.1.2.1 | ||
| OBJECT-TYPE | |||
| ExtremeApsGroupConfigEntry | |||
| extremeApsGroupConfigGroupNumber | 1.3.6.1.4.1.1916.1.20.1.1.2.1.1 | ||
| The group number which uniquely identifies the APS group. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| extremeApsGroupConfigRevertMode | 1.3.6.1.4.1.1916.1.20.1.1.2.1.2 | ||
| The revertive mode configured for the APS group. This indicates whether APS will switch-back automatically after the working line error is cleared. In non-revertive mode, manual intervention is required for switch-back. | |||
| OBJECT-TYPE | |||
| INTEGER | revertive(1), nonRevertive(2) | ||
| extremeApsGroupConfigRevertMinutes | 1.3.6.1.4.1.1916.1.20.1.1.2.1.3 | ||
| The number of minutes APS will wait after the error has been cleared before switching back to the working line. During this interval, the K1 request will indicate WTR (wait-to-restore). This field is only valid in revertive mode. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..12 | ||
| extremeApsGroupConfigDirection | 1.3.6.1.4.1.1916.1.20.1.1.2.1.4 | ||
| The directional mode configured for the APS group. This indicates whether protection switches are coordinated between both POS equipment and ADM (bidirectional) or not (unidirectional). | |||
| OBJECT-TYPE | |||
| INTEGER | bidirectional(1), unidirectional(2) | ||
| extremeApsGroupConfigTimerInterval | 1.3.6.1.4.1.1916.1.20.1.1.2.1.5 | ||
| The number of seconds between APS out-of-band peer protocol hello messages. This value is relevant when the working line and protection line exist is physically different chassis. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsGroupConfigTimerMisses | 1.3.6.1.4.1.1916.1.20.1.1.2.1.6 | ||
| The number of APS out-of-band peer protocol messages transmitted without receiving a response before the protection switch declares the working switch inoperable. When this occurs the protection switch initiates a line switch over via APS. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsGroupConfigAuthenticate | 1.3.6.1.4.1.1916.1.20.1.1.2.1.7 | ||
| When enabled, the authentication string on both working and protection switches must match. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| extremeApsGroupConfigAuthString | 1.3.6.1.4.1.1916.1.20.1.1.2.1.8 | ||
| If configured, this is the authentication string that must match between working and protection switches. This field is relevant if the APS group is configured to authenticate. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..8) | ||
| extremeApsPortConfigTable | 1.3.6.1.4.1.1916.1.20.1.1.3 | ||
| This table contains configuration information for APS ports. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ExtremeApsPortConfigEntry | |||
| extremeApsPortConfigEntry | 1.3.6.1.4.1.1916.1.20.1.1.3.1 | ||
| OBJECT-TYPE | |||
| ExtremeApsPortConfigEntry | |||
| extremeApsPortConfigGroupNumber | 1.3.6.1.4.1.1916.1.20.1.1.3.1.1 | ||
| The group number which uniquely identifies the APS group. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| extremeApsPortConfigPortNumber | 1.3.6.1.4.1.1916.1.20.1.1.3.1.2 | ||
| The value of ifIndex that identifies the port. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsPortConfigPortType | 1.3.6.1.4.1.1916.1.20.1.1.3.1.3 | ||
| The port type designation. | |||
| OBJECT-TYPE | |||
| INTEGER | working(1), protection(2) | ||
| extremeApsProtectPortConfigTable | 1.3.6.1.4.1.1916.1.20.1.1.4 | ||
| This table contains configuration information for APS protection ports. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ExtremeApsProtectPortConfigEntry | |||
| extremeApsProtectPortConfigEntry | 1.3.6.1.4.1.1916.1.20.1.1.4.1 | ||
| OBJECT-TYPE | |||
| ExtremeApsProtectPortConfigEntry | |||
| extremeApsProtectPortConfigGroupNumber | 1.3.6.1.4.1.1916.1.20.1.1.4.1.1 | ||
| The group number which uniquely identifies the APS group. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| extremeApsProtectPortConfigPortNumber | 1.3.6.1.4.1.1916.1.20.1.1.4.1.2 | ||
| The value of ifIndex that identifies the protection port. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsProtectPortConfigWorkingIpAddr | 1.3.6.1.4.1.1916.1.20.1.1.4.1.3 | ||
| The IP address of the working switch. If the working and protection lines reside on the same chassis, this IP address will be a local address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| extremeApsStatus | 1.3.6.1.4.1.1916.1.20.1.2 | ||
| OBJECT IDENTIFIER | |||
| extremeApsGroupTable | 1.3.6.1.4.1.1916.1.20.1.2.1 | ||
| This table contains run-time information by defined APS group. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ExtremeApsGroupEntry | |||
| extremeApsGroupEntry | 1.3.6.1.4.1.1916.1.20.1.2.1.1 | ||
| OBJECT-TYPE | |||
| ExtremeApsGroupEntry | |||
| extremeApsGroupGroupNumber | 1.3.6.1.4.1.1916.1.20.1.2.1.1.1 | ||
| The group number which uniquely identifies the APS group. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| extremeApsGroupActivePort | 1.3.6.1.4.1.1916.1.20.1.2.1.1.2 | ||
| The APS port which is currently carrying the network traffic. | |||
| OBJECT-TYPE | |||
| INTEGER | working(1), protection(2) | ||
| extremeApsGroupEffectiveDirection | 1.3.6.1.4.1.1916.1.20.1.2.1.1.3 | ||
| The effective directional mode for the APS group. When this value differs from the configured directional mode, check the ADM and switch provisioning for a mis- configuration. | |||
| OBJECT-TYPE | |||
| INTEGER | bidirectional(1), unidirectional(2) | ||
| extremeApsGroupPeerProtoStatus | 1.3.6.1.4.1.1916.1.20.1.2.1.1.4 | ||
| The APS out-of-band peer protocol status for a group. | |||
| OBJECT-TYPE | |||
| INTEGER | established(1), closed(2) | ||
| extremeApsProtectPortTable | 1.3.6.1.4.1.1916.1.20.1.2.2 | ||
| This table contains run-time information by defined APS protection port. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ExtremeApsProtectPortEntry | |||
| extremeApsProtectPortEntry | 1.3.6.1.4.1.1916.1.20.1.2.2.1 | ||
| OBJECT-TYPE | |||
| ExtremeApsProtectPortEntry | |||
| extremeApsProtectPortGroupNumber | 1.3.6.1.4.1.1916.1.20.1.2.2.1.1 | ||
| The group number which uniquely identifies the APS group. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| extremeApsProtectPortPortNumber | 1.3.6.1.4.1.1916.1.20.1.2.2.1.2 | ||
| The value of ifIndex that identifies the protection port. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsProtectPortTransmitK1 | 1.3.6.1.4.1.1916.1.20.1.2.2.1.3 | ||
| The K1 overhead byte currently being transmitted on the indicated protection port. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| extremeApsProtectPortTransmitK2 | 1.3.6.1.4.1.1916.1.20.1.2.2.1.4 | ||
| The K2 overhead byte currently being transmitted on the indicated protection port. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| extremeApsProtectPortReceiveK1 | 1.3.6.1.4.1.1916.1.20.1.2.2.1.5 | ||
| The K1 overhead byte currently being received on the indicated protection port. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| extremeApsProtectPortReceiveK2 | 1.3.6.1.4.1.1916.1.20.1.2.2.1.6 | ||
| The K2 overhead byte currently being received on the indicated protection port. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| extremeApsProtectPortSwitchInitByWorking | 1.3.6.1.4.1.1916.1.20.1.2.2.1.7 | ||
| The number of switches that have been initiated by the working-line router. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsProtectPortSwitchInitByProtect | 1.3.6.1.4.1.1916.1.20.1.2.2.1.8 | ||
| The number of switches that have been initiated by the protection-line router. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsProtectPortSwitchInitByADM | 1.3.6.1.4.1.1916.1.20.1.2.2.1.9 | ||
| The number of switches that have been initiated by the ADM. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsProtectPortSwitchInitByCmd | 1.3.6.1.4.1.1916.1.20.1.2.2.1.10 | ||
| The number of switches that have been initiated by an external CLI command. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsProtectPortSuccessfulSwitches | 1.3.6.1.4.1.1916.1.20.1.2.2.1.11 | ||
| The number of successful APS line switches. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsProtectPortHelloProtFails | 1.3.6.1.4.1.1916.1.20.1.2.2.1.12 | ||
| The number of APS out-of-band peer protocol failures recorded. This situation causes the protection-line router to initiate a line switch. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsErrors | 1.3.6.1.4.1.1916.1.20.1.3 | ||
| OBJECT IDENTIFIER | |||
| extremeApsLineErrorTable | 1.3.6.1.4.1.1916.1.20.1.3.1 | ||
| This table contains APS line error information. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ExtremeApsLineErrorEntry | |||
| extremeApsLineErrorEntry | 1.3.6.1.4.1.1916.1.20.1.3.1.1 | ||
| OBJECT-TYPE | |||
| ExtremeApsLineErrorEntry | |||
| extremeApsLineErrorGroupNumber | 1.3.6.1.4.1.1916.1.20.1.3.1.1.1 | ||
| The group number which uniquely identifies the APS group. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| extremeApsLineErrorPortNumber | 1.3.6.1.4.1.1916.1.20.1.3.1.1.2 | ||
| The ifIndex value which identifies the APS port. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsLineErrorSignalDegradeActive | 1.3.6.1.4.1.1916.1.20.1.3.1.1.3 | ||
| Indicates whether a signal degrade condition currently exists on the line. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| extremeApsLineErrorBERSignalDegradeActive | 1.3.6.1.4.1.1916.1.20.1.3.1.1.4 | ||
| Indicates whether a signal degrade condition due to excessive Bit-Error-Rate currently exists on the line. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| extremeApsLineErrorSignalFailActive | 1.3.6.1.4.1.1916.1.20.1.3.1.1.5 | ||
| Indicates whether a signal fail condition currently exists on the line. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| extremeApsLineErrorBERSignalFailActive | 1.3.6.1.4.1.1916.1.20.1.3.1.1.6 | ||
| Indicates whether a signal fail condition due to excessive Bit-Error-Rate currently exists on the line. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| extremeApsLineErrorSignalDegrades | 1.3.6.1.4.1.1916.1.20.1.3.1.1.7 | ||
| The number of signal degrades that have been recorded on the line. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsLineErrorBERSignalDegrades | 1.3.6.1.4.1.1916.1.20.1.3.1.1.8 | ||
| The number of signal degrades due to excessive Bit-Error-Rate that have been recorded on the line. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsLineErrorSignalFails | 1.3.6.1.4.1.1916.1.20.1.3.1.1.9 | ||
| The number of signal fails that have been recorded on the line. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsLineErrorBERSignalFails | 1.3.6.1.4.1.1916.1.20.1.3.1.1.10 | ||
| The number of signal fails due to excessive Bit-Error-Rate that have been recorded on the line. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsProtocolErrorTable | 1.3.6.1.4.1.1916.1.20.1.3.2 | ||
| This table contains APS protocol error information. These errors are relevant for APS protection ports. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ExtremeApsProtocolErrorEntry | |||
| extremeApsProtocolErrorEntry | 1.3.6.1.4.1.1916.1.20.1.3.2.1 | ||
| OBJECT-TYPE | |||
| ExtremeApsProtocolErrorEntry | |||
| extremeApsProtocolErrorGroupNumber | 1.3.6.1.4.1.1916.1.20.1.3.2.1.1 | ||
| The group number which uniquely identifies the APS group. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| extremeApsProtocolErrorPortNumber | 1.3.6.1.4.1.1916.1.20.1.3.2.1.2 | ||
| The ifIndex value which identifies the APS protection port. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsProtocolErrorModeMismatchDefect | 1.3.6.1.4.1.1916.1.20.1.3.2.1.3 | ||
| Indicates whether a Mode Mismatch defect currently exists on the port. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| extremeApsProtocolErrorProtSwitchByteDefect | 1.3.6.1.4.1.1916.1.20.1.3.2.1.4 | ||
| Indicates whether a Protection Switching Byte defect currently exists on the port. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| extremeApsProtocolErrorChannelMismatchDefect | 1.3.6.1.4.1.1916.1.20.1.3.2.1.5 | ||
| Indicates whether a Channel Mismatch defect currently exists on the port. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| extremeApsProtocolErrorFarEndProtectDefect | 1.3.6.1.4.1.1916.1.20.1.3.2.1.6 | ||
| Indicates whether a Far-End Protection defect currently exists on the port. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| extremeApsProtocolErrorModeMismatchFailure | 1.3.6.1.4.1.1916.1.20.1.3.2.1.7 | ||
| Indicates whether a Mode Mismatch failure currently exists on the port. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| extremeApsProtocolErrorProtSwitchByteFailure | 1.3.6.1.4.1.1916.1.20.1.3.2.1.8 | ||
| Indicates whether a Protection Switching Byte failure currently exists on the port. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| extremeApsProtocolErrorChannelMismatchFailure | 1.3.6.1.4.1.1916.1.20.1.3.2.1.9 | ||
| Indicates whether a Channel Mismatch failure currently exists on the port. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| extremeApsProtocolErrorFarEndProtectFailure | 1.3.6.1.4.1.1916.1.20.1.3.2.1.10 | ||
| Indicates whether a Far-End Protection failure currently exists on the port. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| extremeApsProtocolErrorModeMismatchNumFails | 1.3.6.1.4.1.1916.1.20.1.3.2.1.11 | ||
| The number of Mode Mismatch failures that have been recorded. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsProtocolErrorProtSwitchByteNumFails | 1.3.6.1.4.1.1916.1.20.1.3.2.1.12 | ||
| The number of Protection Switching Byte failures that have been recorded. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsProtocolErrorChannelMismatchNumFails | 1.3.6.1.4.1.1916.1.20.1.3.2.1.13 | ||
| The number of Channel Mismatch failures that have been recorded. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| extremeApsProtocolErrorFarEndProtectNumFails | 1.3.6.1.4.1.1916.1.20.1.3.2.1.14 | ||
| The number of Far-End Protection failures that have been recorded. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| ExtremeApsGroupConfigEntry | |||
| SEQUENCE | |||
| INTEGER as extremeApsGroupConfigGroupNumber | 1..65535 | ||
| INTEGER as extremeApsGroupConfigRevertMode | |||
| INTEGER as extremeApsGroupConfigRevertMinutes | 0..12 | ||
| INTEGER as extremeApsGroupConfigDirection | |||
| INTEGER as extremeApsGroupConfigTimerInterval | |||
| INTEGER as extremeApsGroupConfigTimerMisses | |||
| TruthValue as extremeApsGroupConfigAuthenticate | |||
| DisplayString as extremeApsGroupConfigAuthString | |||
| ExtremeApsPortConfigEntry | |||
| SEQUENCE | |||
| INTEGER as extremeApsPortConfigGroupNumber | 1..65535 | ||
| INTEGER as extremeApsPortConfigPortNumber | |||
| INTEGER as extremeApsPortConfigPortType | |||
| ExtremeApsProtectPortConfigEntry | |||
| SEQUENCE | |||
| INTEGER as extremeApsProtectPortConfigGroupNumber | 1..65535 | ||
| INTEGER as extremeApsProtectPortConfigPortNumber | |||
| IpAddress as extremeApsProtectPortConfigWorkingIpAddr | |||
| ExtremeApsGroupEntry | |||
| SEQUENCE | |||
| INTEGER as extremeApsGroupGroupNumber | 1..65535 | ||
| INTEGER as extremeApsGroupActivePort | |||
| INTEGER as extremeApsGroupEffectiveDirection | |||
| INTEGER as extremeApsGroupPeerProtoStatus | |||
| ExtremeApsProtectPortEntry | |||
| SEQUENCE | |||
| INTEGER as extremeApsProtectPortGroupNumber | 1..65535 | ||
| INTEGER as extremeApsProtectPortPortNumber | |||
| OCTET STRING as extremeApsProtectPortTransmitK1 | |||
| OCTET STRING as extremeApsProtectPortTransmitK2 | |||
| OCTET STRING as extremeApsProtectPortReceiveK1 | |||
| OCTET STRING as extremeApsProtectPortReceiveK2 | |||
| INTEGER as extremeApsProtectPortSwitchInitByWorking | |||
| INTEGER as extremeApsProtectPortSwitchInitByProtect | |||
| INTEGER as extremeApsProtectPortSwitchInitByADM | |||
| INTEGER as extremeApsProtectPortSwitchInitByCmd | |||
| INTEGER as extremeApsProtectPortSuccessfulSwitches | |||
| INTEGER as extremeApsProtectPortHelloProtFails | |||
| ExtremeApsLineErrorEntry | |||
| SEQUENCE | |||
| INTEGER as extremeApsLineErrorGroupNumber | 1..65535 | ||
| INTEGER as extremeApsLineErrorPortNumber | |||
| TruthValue as extremeApsLineErrorSignalDegradeActive | |||
| TruthValue as extremeApsLineErrorBERSignalDegradeActive | |||
| TruthValue as extremeApsLineErrorSignalFailActive | |||
| TruthValue as extremeApsLineErrorBERSignalFailActive | |||
| INTEGER as extremeApsLineErrorSignalDegrades | |||
| INTEGER as extremeApsLineErrorBERSignalDegrades | |||
| INTEGER as extremeApsLineErrorSignalFails | |||
| INTEGER as extremeApsLineErrorBERSignalFails | |||
| ExtremeApsProtocolErrorEntry | |||
| SEQUENCE | |||
| INTEGER as extremeApsProtocolErrorGroupNumber | 1..65535 | ||
| INTEGER as extremeApsProtocolErrorPortNumber | |||
| TruthValue as extremeApsProtocolErrorModeMismatchDefect | |||
| TruthValue as extremeApsProtocolErrorProtSwitchByteDefect | |||
| TruthValue as extremeApsProtocolErrorChannelMismatchDefect | |||
| TruthValue as extremeApsProtocolErrorFarEndProtectDefect | |||
| TruthValue as extremeApsProtocolErrorModeMismatchFailure | |||
| TruthValue as extremeApsProtocolErrorProtSwitchByteFailure | |||
| TruthValue as extremeApsProtocolErrorChannelMismatchFailure | |||
| TruthValue as extremeApsProtocolErrorFarEndProtectFailure | |||
| INTEGER as extremeApsProtocolErrorModeMismatchNumFails | |||
| INTEGER as extremeApsProtocolErrorProtSwitchByteNumFails | |||
| INTEGER as extremeApsProtocolErrorChannelMismatchNumFails | |||
| INTEGER as extremeApsProtocolErrorFarEndProtectNumFails | |||