
| SNMPv2-SMI | RFC1155-SMI | SNMPv2-TC |
| FLARION-MIB |
| bbuSysTable | 1.3.6.1.4.1.8603.1.2.1.2.5 | ||
| Base Band Unit system information. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| BbuSysEntry | |||
| bbuSysEntry | 1.3.6.1.4.1.8603.1.2.1.2.5.1 | ||
| Base Band Unit system table entry. | |||
| OBJECT-TYPE | |||
| BbuSysEntry | |||
| bbuSysId | 1.3.6.1.4.1.8603.1.2.1.2.5.1.1 | ||
| This identifies a single BBU in a basestation. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| bbuDspVer | 1.3.6.1.4.1.8603.1.2.1.2.5.1.2 | ||
| The read-only statistic indicates the version number of the DSP software currently operational on the sector in question. It has the major.minor.micro notation. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| bbuLlcVer | 1.3.6.1.4.1.8603.1.2.1.2.5.1.3 | ||
| The read-only statistic indicates the version number of the Link List Controller software/firmware currently operational on the sector in question. It has the major.minor notation. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| bbuTxFpgaVer | 1.3.6.1.4.1.8603.1.2.1.2.5.1.4 | ||
| The read-only statistic indicates the version number of the Tx FPGA software/firmware currently operational on the sector in question. It has the major.minor notation. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| bbuRxFpgaVer | 1.3.6.1.4.1.8603.1.2.1.2.5.1.5 | ||
| The read-only statistic indicates the version number of the Rx FPGA software/firmware currently operational on the sector in question. It has the major.minor notation. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| bbuLdpcVer | 1.3.6.1.4.1.8603.1.2.1.2.5.1.6 | ||
| The read-only statistic indicates the version number of the LDPC encoder/decoder software/firmware currently operational on the sector in question. It has the major.minor notation. | |||
| OBJECT-TYPE | |||
| Unsigned32 | |||
| bbuRfChanNum | 1.3.6.1.4.1.8603.1.2.1.2.5.1.50 | ||
| The RF channel number, in conjunction with the bbuRffBand object defines the frequency of operation. The channel number follows well-known ITU numbering, and represents 50 kHz spacing. The step size depends on the band. In the 1.9 GHz band, the step size is 4 (200 kHz). Editable offline. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..2000 | ||
| bbuExtGainTx | 1.3.6.1.4.1.8603.1.2.1.2.5.1.51 | ||
| Represents the total external gain in the Tx path. Typically it equals PA gain minus any attenuators. The value is in dB * 32 (scaled by 32). E.g., default value is 43 dB, which is the PA gain, and is represented as 43*32 = 1376. This parameter is used to assist the mobile in making an access attempt at an appropriate power level. The step size is 1 dB. Editable online. | |||
| OBJECT-TYPE | |||
| INTEGER | -1600..2240 | ||
| bbuExtGainRx | 1.3.6.1.4.1.8603.1.2.1.2.5.1.52 | ||
| Represents the total external gain in the Rx path. Typically it equals LNA gain minus any attenuators. The value is in dB * 32 (scaled by 32). E.g., default value is 31 dB, which is the LNA gain, and is represented as 31*32 = 992. This parameter is used to assist the mobile in making an access attempt at an appropriate power level. The step size is 1 dB. Editable online. | |||
| OBJECT-TYPE | |||
| INTEGER | -1600..2240 | ||
| bbuRfGainRx0 | 1.3.6.1.4.1.8603.1.2.1.2.5.1.53 | ||
| Represents the gain (in dB) provided by the RF Rx blade(RXU) in the Rx0 path. This gain is in addition to the gain provided by the LNA. This value is typically calibrated and set in the factory. The step size is 1 dB. Editable online. | |||
| OBJECT-TYPE | |||
| INTEGER | -10..75 | ||
| bbuRfGainRx1 | 1.3.6.1.4.1.8603.1.2.1.2.5.1.54 | ||
| Represents the gain (in dB) provided by the RF Rx blade(RXU) in the Rx1 path. This gain is in addition to the gain provided by the LNA. This value is typically calibrated and set in the factory. The step size is 1 dB. Editable online. | |||
| OBJECT-TYPE | |||
| INTEGER | -10..75 | ||
| bbuRfBand | 1.3.6.1.4.1.8603.1.2.1.2.5.1.55 | ||
| The band of operation, represented by an enumeration. E.g., the 1.9 GHz PCS band has a value of 6, while the 2.1 GHz UMTS band has a value of 7. This quantity, in conjunction with the bbuRfChanNum decides the frequency of operation. Editable offline. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| bbuRfPowerTx0 | 1.3.6.1.4.1.8603.1.2.1.2.5.1.56 | ||
| Represents the signal strength in dBm of the Tx signal put out on Tx0 by the TXU. An increase in this implies an increase in the signal input to the PA. Step size is 1 dBm. Editable online. | |||
| OBJECT-TYPE | |||
| INTEGER | -20..10 | ||
| bbuRfPowerTx1 | 1.3.6.1.4.1.8603.1.2.1.2.5.1.57 | ||
| Represents the signal strength in dBm of the Tx signal put out on Tx1 by the TXU. An increase in this implies an increase in the signal input to the PA. Step size is 1 dBm. Editable online. | |||
| OBJECT-TYPE | |||
| INTEGER | -20..10 | ||
| bbuRfuEnableMask | 1.3.6.1.4.1.8603.1.2.1.2.5.1.59 | ||
| This is a bit mask to choose between the 0 and 1 channels for Rx and Tx. The value should be an OR of the channels selected, where: Tx0 = 0001 Tx1 = 0010 Rx0 = 0100 Rx1 = 1000 For example, set this object to 6 if Rx0 and Tx1 need to be enabled. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..15 | ||
| bbuExtTxGain | 1.3.6.1.4.1.8603.1.2.1.2.5.1.60 | ||
| External Tx gain. Valid range is -50.0 to 70.0. | |||
| OBJECT-TYPE | |||
| FloatAsString | |||
| bbuExtRxGain | 1.3.6.1.4.1.8603.1.2.1.2.5.1.61 | ||
| External Rx gain. Valid range is -50.0 to 70.0. | |||
| OBJECT-TYPE | |||
| FloatAsString | |||
| bbuRfRx0Gain | 1.3.6.1.4.1.8603.1.2.1.2.5.1.62 | ||
| Represents the gain (in dB) provided by the RF Rx blade(RXU) in the Rx0 path. This gain is in addition to the gain provided by the LNA. This value is typically calibrated and set in the factory. The step size is 1 dB. Valid range is -10.0 to 75.0. Editable online. | |||
| OBJECT-TYPE | |||
| FloatAsString | |||
| bbuRfRx1Gain | 1.3.6.1.4.1.8603.1.2.1.2.5.1.63 | ||
| Represents the gain (in dB) provided by the RF Rx blade(RXU) in the Rx1 path. This gain is in addition to the gain provided by the LNA. This value is typically calibrated and set in the factory. The step size is 1 dB. Valid range is -10.0 to 75.0. Editable online. | |||
| OBJECT-TYPE | |||
| FloatAsString | |||
| bbuRfTx0Power | 1.3.6.1.4.1.8603.1.2.1.2.5.1.64 | ||
| Represents the signal strength in dBm of the Tx signal put out on Tx0 by the TXU. An increase in this implies an increase in the signal input to the PA. Step size is 1 dBm. Valid range is -20.0 to 10.0. Editable online. | |||
| OBJECT-TYPE | |||
| FloatAsString | |||
| bbuRfTx1Power | 1.3.6.1.4.1.8603.1.2.1.2.5.1.65 | ||
| Represents the signal strength in dBm of the Tx signal put out on Tx1 by the TXU. An increase in this implies an increase in the signal input to the PA. Step size is 1 dBm. Valid range is -20.0 to 10.0. Editable online. | |||
| OBJECT-TYPE | |||
| FloatAsString | |||
| bbuTxPwrDeviationLimit | 1.3.6.1.4.1.8603.1.2.1.2.5.1.66 | ||
| OBJECT-TYPE | |||
| INTEGER | 1..10 | ||
| bbuSlope | 1.3.6.1.4.1.8603.1.2.1.2.5.1.70 | ||
| Represents the slope of the RR sector. It is an identifier which allows a mobile to distinguish between signals from different basestations. There are 112 possible slope values, however, only 80 of these are considered valid values. Editable offline. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..112 | ||
| bbuMcastSnr | 1.3.6.1.4.1.8603.1.2.1.2.5.1.71 | ||
| OBJECT-TYPE | |||
| INTEGER | -20..35 | ||
| bbuScmType | 1.3.6.1.4.1.8603.1.2.1.2.5.1.72 | ||
| OBJECT-TYPE | |||
| INTEGER | 0..1 | ||
| bbuSleepInactivityTimer | 1.3.6.1.4.1.8603.1.2.1.2.5.1.91 | ||
| Represents the amount of time of data inactivity (on the forward or reverse links) after which a mobile moves to the Sleep state. In units of 1/3 seconds [ eg. Value = 180 represents 60 seconds]. This time period is conveyed to the mobile at the time of establishing connectivity with the basestation. This quantity is non-linearly quantized, so the actual duration of inactivity before sleep may be slightly different from this value. Step size is 1/3 second. Range is 0 to 20 minutes. 0 means never go to sleep. Recommended value is 180 (i.e., 60sec). Editable online. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..3600 | ||
| bbuLuTimer | 1.3.6.1.4.1.8603.1.2.1.2.5.1.100 | ||
| Periodicity, in seconds, of location update done by a stationary mobile. This time period is conveyed to the mobile at the time of establishing connectivity with the RR. This quantity is non-linearly quantized, so the actual duration of location update may be slightly different from this value. Step size is 1 second. Range is 5 seconds to 18 hours. Editable online. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..86400 | ||
| rrChassis | 1.3.6.1.4.1.8603.1.2.1.8 | ||
| OBJECT IDENTIFIER | |||
| rrChassisType | 1.3.6.1.4.1.8603.1.2.1.8.1 | ||
| The chassis revision. | |||
| OBJECT-TYPE | |||
| ChassisType | |||
| rrChassisRev | 1.3.6.1.4.1.8603.1.2.1.8.2 | ||
| The chassis revision. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| rrChassisMaxSlots | 1.3.6.1.4.1.8603.1.2.1.8.3 | ||
| Maximum number of slots in the chassis. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| rrChassisNumCards | 1.3.6.1.4.1.8603.1.2.1.8.4 | ||
| Number of cards detected in the chassis. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| rrChassisTable | 1.3.6.1.4.1.8603.1.2.1.8.5 | ||
| Table containing chassis card information. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RrChassisTableEntry | |||
| rrChassisTableEntry | 1.3.6.1.4.1.8603.1.2.1.8.5.1 | ||
| RadioRouter chassis card table entry. | |||
| OBJECT-TYPE | |||
| RrChassisTableEntry | |||
| rrChassisSlotId | 1.3.6.1.4.1.8603.1.2.1.8.5.1.1 | ||
| The chassis slot of the card. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| rrChassisSlotHwType | 1.3.6.1.4.1.8603.1.2.1.8.5.1.2 | ||
| The card type. | |||
| OBJECT-TYPE | |||
| MoType | |||
| rrChassisSlotHwName | 1.3.6.1.4.1.8603.1.2.1.8.5.1.3 | ||
| The card name. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| rrChassisSlotHwStatus | 1.3.6.1.4.1.8603.1.2.1.8.5.1.4 | ||
| The card hardware operational status. | |||
| OBJECT-TYPE | |||
| CardOpState | |||
| rrChassisSlotHwVer | 1.3.6.1.4.1.8603.1.2.1.8.5.1.5 | ||
| The card hardware version number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| rrChassisSlotHwEsn | 1.3.6.1.4.1.8603.1.2.1.8.5.1.6 | ||
| The card Electronic Serial Number. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| rrChassisSlotSwVer | 1.3.6.1.4.1.8603.1.2.1.8.5.1.8 | ||
| The card IPMI (Intelligent Platform Management Interface) firmware version number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| rrPhyShelf | 1.3.6.1.4.1.8603.1.2.3 | ||
| OBJECT IDENTIFIER | |||
| phyChassisType | 1.3.6.1.4.1.8603.1.2.3.1 | ||
| Chassis type. | |||
| OBJECT-TYPE | |||
| ChassisType | |||
| phySerialNumber | 1.3.6.1.4.1.8603.1.2.3.2 | ||
| Chassis serial number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyProductionDate | 1.3.6.1.4.1.8603.1.2.3.3 | ||
| Chassis production date (mm/dd/yyyy). | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyPartNumber | 1.3.6.1.4.1.8603.1.2.3.4 | ||
| Chassis part number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyHardwareVersion | 1.3.6.1.4.1.8603.1.2.3.5 | ||
| Chassis hardware version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyChassisRfBand | 1.3.6.1.4.1.8603.1.2.3.6 | ||
| Chassis RF band. | |||
| OBJECT-TYPE | |||
| RfBand | |||
| phyAssemblyId | 1.3.6.1.4.1.8603.1.2.3.7 | ||
| Chassis assembly ID. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyFanTable | 1.3.6.1.4.1.8603.1.2.3.10 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PhyFanEntry | |||
| phyFanEntry | 1.3.6.1.4.1.8603.1.2.3.10.1 | ||
| OBJECT-TYPE | |||
| PhyFanEntry | |||
| phyFanIndex | 1.3.6.1.4.1.8603.1.2.3.10.1.1 | ||
| Fan index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| phyFanOk | 1.3.6.1.4.1.8603.1.2.3.10.1.2 | ||
| Fan status. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| phyRelayTable | 1.3.6.1.4.1.8603.1.2.3.11 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PhyRelayEntry | |||
| phyRelayEntry | 1.3.6.1.4.1.8603.1.2.3.11.1 | ||
| OBJECT-TYPE | |||
| PhyRelayEntry | |||
| phyRelayIndex | 1.3.6.1.4.1.8603.1.2.3.11.1.1 | ||
| Relay index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| phyRelayName | 1.3.6.1.4.1.8603.1.2.3.11.1.2 | ||
| Relay name. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyRelayState | 1.3.6.1.4.1.8603.1.2.3.11.1.3 | ||
| Relay state. | |||
| OBJECT-TYPE | |||
| RelayState | |||
| phyAlarmInputTable | 1.3.6.1.4.1.8603.1.2.3.12 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PhyAlarmInputEntry | |||
| phyAlarmInputEntry | 1.3.6.1.4.1.8603.1.2.3.12.1 | ||
| OBJECT-TYPE | |||
| PhyAlarmInputEntry | |||
| phyAlarmInputIndex | 1.3.6.1.4.1.8603.1.2.3.12.1.1 | ||
| AlarmInput index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| phyAlarmInputEnable | 1.3.6.1.4.1.8603.1.2.3.12.1.2 | ||
| AlarmInput enable. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| phyAlarmInputName | 1.3.6.1.4.1.8603.1.2.3.12.1.3 | ||
| AlarmInput name. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyAlarmInputState | 1.3.6.1.4.1.8603.1.2.3.12.1.4 | ||
| AlarmInput state. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| phyPcuTable | 1.3.6.1.4.1.8603.1.2.3.13 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PhyPcuEntry | |||
| phyPcuEntry | 1.3.6.1.4.1.8603.1.2.3.13.1 | ||
| OBJECT-TYPE | |||
| PhyPcuEntry | |||
| phyPcuIndex | 1.3.6.1.4.1.8603.1.2.3.13.1.1 | ||
| PCU index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| phyPcuPowerFail | 1.3.6.1.4.1.8603.1.2.3.13.1.2 | ||
| PCU power fail. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| phyAiuTable | 1.3.6.1.4.1.8603.1.2.3.14 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PhyAiuEntry | |||
| phyAiuEntry | 1.3.6.1.4.1.8603.1.2.3.14.1 | ||
| OBJECT-TYPE | |||
| PhyAiuEntry | |||
| phyAiuIndex | 1.3.6.1.4.1.8603.1.2.3.14.1.1 | ||
| AIU index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| phyAiuOpState | 1.3.6.1.4.1.8603.1.2.3.14.1.2 | ||
| AIU operational state. | |||
| OBJECT-TYPE | |||
| CardOpState | |||
| phyAiuFaultLed | 1.3.6.1.4.1.8603.1.2.3.14.1.3 | ||
| AIU fault LED color. | |||
| OBJECT-TYPE | |||
| CardFaultLed | |||
| phyAiuTempStatus | 1.3.6.1.4.1.8603.1.2.3.14.1.4 | ||
| AIU temperature status. | |||
| OBJECT-TYPE | |||
| CardTempStatus | |||
| phyAiuVoltageStatus | 1.3.6.1.4.1.8603.1.2.3.14.1.5 | ||
| AIU voltage status. | |||
| OBJECT-TYPE | |||
| CardVoltageStatus | |||
| phyAiuSerialNumber | 1.3.6.1.4.1.8603.1.2.3.14.1.6 | ||
| AIU serial number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyAiuProductionDate | 1.3.6.1.4.1.8603.1.2.3.14.1.7 | ||
| AIU production date. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyAiuPartNumber | 1.3.6.1.4.1.8603.1.2.3.14.1.8 | ||
| AIU part number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyAiuDescription | 1.3.6.1.4.1.8603.1.2.3.14.1.9 | ||
| AIU description. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyAiuHardwareVersion | 1.3.6.1.4.1.8603.1.2.3.14.1.10 | ||
| AIU hardware version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyAiuIpmiSwVersion | 1.3.6.1.4.1.8603.1.2.3.14.1.11 | ||
| AIU IPMI software version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyAiuAssemblyId | 1.3.6.1.4.1.8603.1.2.3.14.1.12 | ||
| AIU assembly ID. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyAiuAssemblyIdSrc | 1.3.6.1.4.1.8603.1.2.3.14.1.13 | ||
| AIU assembly ID source. | |||
| OBJECT-TYPE | |||
| AssemblyIdSource | |||
| phyAiuExcessiveFakeAid | 1.3.6.1.4.1.8603.1.2.3.14.1.14 | ||
| This object is true(1) if the assembly ID is programmed under more than one source. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| phyAiuAdminState | 1.3.6.1.4.1.8603.1.2.3.14.1.20 | ||
| AIU administrative state. | |||
| OBJECT-TYPE | |||
| AdminState | |||
| phyAiuRebootRr | 1.3.6.1.4.1.8603.1.2.3.14.1.21 | ||
| Setting this object to true(1) will power cycle the RadioRouter chassis! | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| phyMcuTable | 1.3.6.1.4.1.8603.1.2.3.15 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PhyMcuEntry | |||
| phyMcuEntry | 1.3.6.1.4.1.8603.1.2.3.15.1 | ||
| OBJECT-TYPE | |||
| PhyMcuEntry | |||
| phyMcuIndex | 1.3.6.1.4.1.8603.1.2.3.15.1.1 | ||
| MCU index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| phyMcuOpState | 1.3.6.1.4.1.8603.1.2.3.15.1.2 | ||
| MCU operational state. | |||
| OBJECT-TYPE | |||
| CardOpState | |||
| phyMcuFaultLed | 1.3.6.1.4.1.8603.1.2.3.15.1.3 | ||
| MCU fault LED color. | |||
| OBJECT-TYPE | |||
| CardFaultLed | |||
| phyMcuTempStatus | 1.3.6.1.4.1.8603.1.2.3.15.1.4 | ||
| MCU temperature status. | |||
| OBJECT-TYPE | |||
| CardTempStatus | |||
| phyMcuVoltageStatus | 1.3.6.1.4.1.8603.1.2.3.15.1.5 | ||
| MCU voltage status. | |||
| OBJECT-TYPE | |||
| CardVoltageStatus | |||
| phyMcuSerialNumber | 1.3.6.1.4.1.8603.1.2.3.15.1.6 | ||
| MCU serial number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyMcuProductionDate | 1.3.6.1.4.1.8603.1.2.3.15.1.7 | ||
| MCU production date. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyMcuPartNumber | 1.3.6.1.4.1.8603.1.2.3.15.1.8 | ||
| MCU part number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyMcuDescription | 1.3.6.1.4.1.8603.1.2.3.15.1.9 | ||
| MCU description. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyMcuHardwareVersion | 1.3.6.1.4.1.8603.1.2.3.15.1.10 | ||
| MCU hardware version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyMcuIpmiSwVersion | 1.3.6.1.4.1.8603.1.2.3.15.1.11 | ||
| MCU IPMI software version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyMcuAssemblyId | 1.3.6.1.4.1.8603.1.2.3.15.1.12 | ||
| MCU assembly ID. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyMcuAssemblyIdSrc | 1.3.6.1.4.1.8603.1.2.3.15.1.13 | ||
| MCU assembly ID source. | |||
| OBJECT-TYPE | |||
| AssemblyIdSource | |||
| phyMcuExcessiveFakeAid | 1.3.6.1.4.1.8603.1.2.3.15.1.14 | ||
| This object is true if the assembly ID is programmed under more than one source. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| phyMcuAdminState | 1.3.6.1.4.1.8603.1.2.3.15.1.20 | ||
| MCU administrative state. | |||
| OBJECT-TYPE | |||
| AdminState | |||
| phyCpldVersion | 1.3.6.1.4.1.8603.1.2.3.15.1.21 | ||
| MCU CPLD version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyBbuTable | 1.3.6.1.4.1.8603.1.2.3.16 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PhyBbuEntry | |||
| phyBbuEntry | 1.3.6.1.4.1.8603.1.2.3.16.1 | ||
| OBJECT-TYPE | |||
| PhyBbuEntry | |||
| phyBbuIndex | 1.3.6.1.4.1.8603.1.2.3.16.1.1 | ||
| BBU index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| phyBbuOpState | 1.3.6.1.4.1.8603.1.2.3.16.1.2 | ||
| BBU operational state. | |||
| OBJECT-TYPE | |||
| CardOpState | |||
| phyBbuFaultLed | 1.3.6.1.4.1.8603.1.2.3.16.1.3 | ||
| BBU fault LED color. | |||
| OBJECT-TYPE | |||
| CardFaultLed | |||
| phyBbuTempStatus | 1.3.6.1.4.1.8603.1.2.3.16.1.4 | ||
| BBU temperature status. | |||
| OBJECT-TYPE | |||
| CardTempStatus | |||
| phyBbuVoltageStatus | 1.3.6.1.4.1.8603.1.2.3.16.1.5 | ||
| BBU voltage status. | |||
| OBJECT-TYPE | |||
| CardVoltageStatus | |||
| phyBbuSerialNumber | 1.3.6.1.4.1.8603.1.2.3.16.1.6 | ||
| BBU serial number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyBbuProductionDate | 1.3.6.1.4.1.8603.1.2.3.16.1.7 | ||
| BBU production date. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyBbuPartNumber | 1.3.6.1.4.1.8603.1.2.3.16.1.8 | ||
| BBU part number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyBbuDescription | 1.3.6.1.4.1.8603.1.2.3.16.1.9 | ||
| BBU description. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyBbuHardwareVersion | 1.3.6.1.4.1.8603.1.2.3.16.1.10 | ||
| BBU hardware version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyBbuIpmiSwVersion | 1.3.6.1.4.1.8603.1.2.3.16.1.11 | ||
| BBU IPMI software version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyBbuAssemblyId | 1.3.6.1.4.1.8603.1.2.3.16.1.12 | ||
| BBU assembly Id. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyBbuAssemblyIdSrc | 1.3.6.1.4.1.8603.1.2.3.16.1.13 | ||
| BBU assembly Id source. | |||
| OBJECT-TYPE | |||
| AssemblyIdSource | |||
| phyBbuExcessiveFakeAid | 1.3.6.1.4.1.8603.1.2.3.16.1.14 | ||
| This object is true if the assembly ID is programmed under more than one source. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| phyBbuAdminState | 1.3.6.1.4.1.8603.1.2.3.16.1.20 | ||
| BBU administrative state. | |||
| OBJECT-TYPE | |||
| AdminState | |||
| phyRxuTable | 1.3.6.1.4.1.8603.1.2.3.17 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PhyRxuEntry | |||
| phyRxuEntry | 1.3.6.1.4.1.8603.1.2.3.17.1 | ||
| OBJECT-TYPE | |||
| PhyRxuEntry | |||
| phyRxuIndex | 1.3.6.1.4.1.8603.1.2.3.17.1.1 | ||
| RXU index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| phyRxuOpState | 1.3.6.1.4.1.8603.1.2.3.17.1.2 | ||
| RXU operational state. | |||
| OBJECT-TYPE | |||
| CardOpState | |||
| phyRxuFaultLed | 1.3.6.1.4.1.8603.1.2.3.17.1.3 | ||
| RXU fault LED color. | |||
| OBJECT-TYPE | |||
| CardFaultLed | |||
| phyRxuTempStatus | 1.3.6.1.4.1.8603.1.2.3.17.1.4 | ||
| RXU temperature status. | |||
| OBJECT-TYPE | |||
| CardTempStatus | |||
| phyRxuVoltageStatus | 1.3.6.1.4.1.8603.1.2.3.17.1.5 | ||
| RXU voltage status. | |||
| OBJECT-TYPE | |||
| CardVoltageStatus | |||
| phyRxuSerialNumber | 1.3.6.1.4.1.8603.1.2.3.17.1.6 | ||
| RXU serial number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyRxuProductionDate | 1.3.6.1.4.1.8603.1.2.3.17.1.7 | ||
| RXU production date. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyRxuPartNumber | 1.3.6.1.4.1.8603.1.2.3.17.1.8 | ||
| RXU part number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyRxuDescription | 1.3.6.1.4.1.8603.1.2.3.17.1.9 | ||
| RXU description. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyRxuHardwareVersion | 1.3.6.1.4.1.8603.1.2.3.17.1.10 | ||
| RXU hardware version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyRxuIpmiSwVersion | 1.3.6.1.4.1.8603.1.2.3.17.1.11 | ||
| RXU IPMI software version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyRxuAssemblyId | 1.3.6.1.4.1.8603.1.2.3.17.1.12 | ||
| RXU assembly ID. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyRxuAssemblyIdSrc | 1.3.6.1.4.1.8603.1.2.3.17.1.13 | ||
| RXU assembly ID source. | |||
| OBJECT-TYPE | |||
| AssemblyIdSource | |||
| phyRxuExcessiveFakeAid | 1.3.6.1.4.1.8603.1.2.3.17.1.14 | ||
| This object is true if the assembly ID is programmed under more than one source. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| phyRxuAdminState | 1.3.6.1.4.1.8603.1.2.3.17.1.20 | ||
| RXU administrative state. | |||
| OBJECT-TYPE | |||
| AdminState | |||
| phyRxuRfBand | 1.3.6.1.4.1.8603.1.2.3.17.1.21 | ||
| RXU RF band. | |||
| OBJECT-TYPE | |||
| RfBand | |||
| phyTxuTable | 1.3.6.1.4.1.8603.1.2.3.18 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PhyTxuEntry | |||
| phyTxuEntry | 1.3.6.1.4.1.8603.1.2.3.18.1 | ||
| OBJECT-TYPE | |||
| PhyTxuEntry | |||
| phyTxuIndex | 1.3.6.1.4.1.8603.1.2.3.18.1.1 | ||
| TXU index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| phyTxuOpState | 1.3.6.1.4.1.8603.1.2.3.18.1.2 | ||
| TXU operational state. | |||
| OBJECT-TYPE | |||
| CardOpState | |||
| phyTxuFaultLed | 1.3.6.1.4.1.8603.1.2.3.18.1.3 | ||
| TXU fault LED color. | |||
| OBJECT-TYPE | |||
| CardFaultLed | |||
| phyTxuTempStatus | 1.3.6.1.4.1.8603.1.2.3.18.1.4 | ||
| TXU temperature status. | |||
| OBJECT-TYPE | |||
| CardTempStatus | |||
| phyTxuVoltageStatus | 1.3.6.1.4.1.8603.1.2.3.18.1.5 | ||
| TXU voltage status. | |||
| OBJECT-TYPE | |||
| CardVoltageStatus | |||
| phyTxuSerialNumber | 1.3.6.1.4.1.8603.1.2.3.18.1.6 | ||
| TXU serial number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyTxuProductionDate | 1.3.6.1.4.1.8603.1.2.3.18.1.7 | ||
| TXU production date. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyTxuPartNumber | 1.3.6.1.4.1.8603.1.2.3.18.1.8 | ||
| TXU part number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyTxuDescription | 1.3.6.1.4.1.8603.1.2.3.18.1.9 | ||
| TXU description. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyTxuHardwareVersion | 1.3.6.1.4.1.8603.1.2.3.18.1.10 | ||
| TXU hardware version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyTxuIpmiSwVersion | 1.3.6.1.4.1.8603.1.2.3.18.1.11 | ||
| TXU IPMI software version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyTxuAssemblyId | 1.3.6.1.4.1.8603.1.2.3.18.1.12 | ||
| TXU assembly ID. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| phyTxuAssemblyIdSrc | 1.3.6.1.4.1.8603.1.2.3.18.1.13 | ||
| TXU assembly ID source. | |||
| OBJECT-TYPE | |||
| AssemblyIdSource | |||
| phyTxuExcessiveFakeAid | 1.3.6.1.4.1.8603.1.2.3.18.1.14 | ||
| This object is true if the assembly ID is programmed under more than one source. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| phyTxuAdminState | 1.3.6.1.4.1.8603.1.2.3.18.1.20 | ||
| TXU administrative state. | |||
| OBJECT-TYPE | |||
| AdminState | |||
| phyTxuRfBand | 1.3.6.1.4.1.8603.1.2.3.18.1.21 | ||
| TXU RF band. | |||
| OBJECT-TYPE | |||
| RfBand | |||
| rrPaShelf | 1.3.6.1.4.1.8603.1.2.4 | ||
| OBJECT IDENTIFIER | |||
| paTable | 1.3.6.1.4.1.8603.1.2.4.1 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PaEntry | |||
| paEntry | 1.3.6.1.4.1.8603.1.2.4.1.1 | ||
| OBJECT-TYPE | |||
| PaEntry | |||
| paIndex | 1.3.6.1.4.1.8603.1.2.4.1.1.1 | ||
| Power Amp index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| paAdminState | 1.3.6.1.4.1.8603.1.2.4.1.1.2 | ||
| PA administrative state. | |||
| OBJECT-TYPE | |||
| AdminState | |||
| paOpState | 1.3.6.1.4.1.8603.1.2.4.1.1.3 | ||
| PA operational state. This object is deprecated in favor of paOperStatus. | |||
| OBJECT-TYPE | |||
| CardOpState | |||
| paTempStatus | 1.3.6.1.4.1.8603.1.2.4.1.1.4 | ||
| PA temperature status. | |||
| OBJECT-TYPE | |||
| CardTempStatus | |||
| paOutputTxPower | 1.3.6.1.4.1.8603.1.2.4.1.1.5 | ||
| PA output transmit power, in dbm. | |||
| OBJECT-TYPE | |||
| FloatAsString | |||
| paInputTxPower | 1.3.6.1.4.1.8603.1.2.4.1.1.6 | ||
| PA input transmit power, in dbm. | |||
| OBJECT-TYPE | |||
| FloatAsString | |||
| paTxReflectedPower | 1.3.6.1.4.1.8603.1.2.4.1.1.7 | ||
| PA transmit reflected power, in dbm. | |||
| OBJECT-TYPE | |||
| FloatAsString | |||
| paDcPowerFault | 1.3.6.1.4.1.8603.1.2.4.1.1.8 | ||
| This object indicates if a PA DC power fault exists. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| paRfOverdriveFault | 1.3.6.1.4.1.8603.1.2.4.1.1.9 | ||
| This object indicates if a PA RF overdrive fault exists. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| paFeedForwardFault | 1.3.6.1.4.1.8603.1.2.4.1.1.10 | ||
| This object indicates if a PA feed forward fault exists. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| paSerialNumber | 1.3.6.1.4.1.8603.1.2.4.1.1.11 | ||
| PA serial number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| paRfBand | 1.3.6.1.4.1.8603.1.2.4.1.1.12 | ||
| PA RF band. This object is deprecated in favor of paRadioFreqBand. | |||
| OBJECT-TYPE | |||
| RfBand | |||
| paHardwareVersion | 1.3.6.1.4.1.8603.1.2.4.1.1.13 | ||
| PA hardware version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| paTemperature | 1.3.6.1.4.1.8603.1.2.4.1.1.14 | ||
| PA temperature (Celcius). | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| paReflectedPowerFault | 1.3.6.1.4.1.8603.1.2.4.1.1.15 | ||
| This object indicates if a reflected power fault exists. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| paUnderPowerFault | 1.3.6.1.4.1.8603.1.2.4.1.1.16 | ||
| This object indicates if an under power fault exists. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| paTargetOutputTxPower | 1.3.6.1.4.1.8603.1.2.4.1.1.17 | ||
| PA target output Tx power. | |||
| OBJECT-TYPE | |||
| FloatAsString | |||
| paOperStatus | 1.3.6.1.4.1.8603.1.2.4.1.1.18 | ||
| PA operational state. | |||
| OBJECT-TYPE | |||
| PaState | |||
| paRadioFreqBand | 1.3.6.1.4.1.8603.1.2.4.1.1.19 | ||
| PA RF band. | |||
| OBJECT-TYPE | |||
| PaRfBand | |||
| paFanSpeedOk | 1.3.6.1.4.1.8603.1.2.4.2 | ||
| This object indicates if the PA shelf fan speed is within normal operating limits. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| paFanTempOk | 1.3.6.1.4.1.8603.1.2.4.3 | ||
| This object indicates if the PA shelf fan temperature is within normal operating limits. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| paBreakerTripped | 1.3.6.1.4.1.8603.1.2.4.4 | ||
| This object indicates if a PA shelf breaker has been tripped. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| paSimulcast | 1.3.6.1.4.1.8603.1.2.4.5 | ||
| This object indicates if the PA shelf supports simulcast. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| paTxCalEnabled | 1.3.6.1.4.1.8603.1.2.4.6 | ||
| This object indicates if PX Gain control loop is enabled. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| paPowerTable | 1.3.6.1.4.1.8603.1.2.4.7 | ||
| This table is used to display PA various Tx power values. These values are store on the system as floating point numbers, but since SNMP cannot display floating point numbers, this table will convert the values to integer. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PaPowerEntry | |||
| paPowerEntry | 1.3.6.1.4.1.8603.1.2.4.7.1 | ||
| OBJECT-TYPE | |||
| PaPowerEntry | |||
| paPowerIndex | 1.3.6.1.4.1.8603.1.2.4.7.1.1 | ||
| PA index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| paPowerTxOutput | 1.3.6.1.4.1.8603.1.2.4.7.1.2 | ||
| PA output Tx power. In order to retain precision in converting the floating point value into integer, the value is first multiplied by 100. For example 43.25dB will be represented as 4325. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| paPowerTxInput | 1.3.6.1.4.1.8603.1.2.4.7.1.3 | ||
| PA input Tx power. In order to retain precision in converting the floating point value into integer, the value is first multiplied by 100. For example -50.75dB will be represented as -5075. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| paPowerTxReflected | 1.3.6.1.4.1.8603.1.2.4.7.1.4 | ||
| PA reflected Tx power. In order to retain precision in converting the floating point value into integer, the value is first multiplied by 100. For example 21.00dB will be represented as 2100. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| ChassisType | |||
| INTEGER | chassisUnknown(0), chassisCpciIndoor(1), chassisCpciOutdoor(2), chassisEnetIndoor(3), chassisEnetOutdoor(4) | ||
| RelayState | |||
| INTEGER | relayUnknown(0), relayOpen(1), relayClosed(2) | ||
| CardOpState | |||
| INTEGER | cardOpStateUnknown(0), cardOpStateNotPresent(1), cardOpStateStandby(2), cardOpStateActive(3), cardOpStateDown(4) | ||
| CardFaultLed | |||
| INTEGER | faultLedUnknown(0), faultLedRed(1), faultLedOrange(2), faultLedGreen(3) | ||
| CardTempStatus | |||
| INTEGER | tempUnknown(0), tempNominal(1), tempHigh(2), tempSevere(3), tempCritical(4) | ||
| CardVoltageStatus | |||
| INTEGER | voltageUnknown(0), voltageNominal(1), voltageLow(2), voltageHigh(3) | ||
| RfBand | |||
| INTEGER | rfBandUnknown(0), rfBandUpper700MHz(1), rfBandLow800MHz(2), rfBandCellBand(3), rfBandSmrBand(4), rfBandPcsKorea(5), rfBandPcsUs(6), rfBandUmts(7), rfBand2P3GHz(8), rfBandMmds(9) | ||
| PaRfBand | |||
| INTEGER | paRfBandUnknown(0), paRfBand747to770MHz(1), paRfBand861to894MHz(2), paRfBand1930to1990MHz(3), paRfBand2370to2400MHz(4), paRfBand2110to2170MHz(5), paRfBand2620to2686MHz(6), paRfBand740Mto746Hz(7) | ||
| PaState | |||
| INTEGER | paStateUnknown(0), paStateProbing(1), paStateNotPresent(2), paStateDisabledByPa(3), paStateDisabledByBts(4), paStateEnabling(5), paStateEnabled(6), paStateDisabling(7) | ||
| AssemblyIdSource | |||
| INTEGER | aidSourceUnknown(0), aidSourceDatabase(1), aidSourceTarget(2) | ||
| RrChassisTableEntry | |||
| SEQUENCE | |||
| INTEGER as rrChassisSlotId | |||
| MoType as rrChassisSlotHwType | |||
| DisplayString as rrChassisSlotHwName | |||
| CardOpState as rrChassisSlotHwStatus | |||
| DisplayString as rrChassisSlotHwVer | |||
| OCTET STRING as rrChassisSlotHwEsn | |||
| DisplayString as rrChassisSlotSwVer | |||
| PhyFanEntry | |||
| SEQUENCE | |||
| INTEGER as phyFanIndex | |||
| TruthValue as phyFanOk | |||
| PhyRelayEntry | |||
| SEQUENCE | |||
| INTEGER as phyRelayIndex | |||
| DisplayString as phyRelayName | |||
| RelayState as phyRelayState | |||
| PhyAlarmInputEntry | |||
| SEQUENCE | |||
| INTEGER as phyAlarmInputIndex | |||
| TruthValue as phyAlarmInputEnable | |||
| DisplayString as phyAlarmInputName | |||
| TruthValue as phyAlarmInputState | |||
| PhyPcuEntry | |||
| SEQUENCE | |||
| INTEGER as phyPcuIndex | |||
| TruthValue as phyPcuPowerFail | |||
| PhyAiuEntry | |||
| SEQUENCE | |||
| INTEGER as phyAiuIndex | |||
| CardOpState as phyAiuOpState | |||
| CardFaultLed as phyAiuFaultLed | |||
| CardTempStatus as phyAiuTempStatus | |||
| CardVoltageStatus as phyAiuVoltageStatus | |||
| DisplayString as phyAiuSerialNumber | |||
| DisplayString as phyAiuProductionDate | |||
| DisplayString as phyAiuPartNumber | |||
| DisplayString as phyAiuDescription | |||
| DisplayString as phyAiuHardwareVersion | |||
| DisplayString as phyAiuIpmiSwVersion | |||
| DisplayString as phyAiuAssemblyId | |||
| AssemblyIdSource as phyAiuAssemblyIdSrc | |||
| TruthValue as phyAiuExcessiveFakeAid | |||
| AdminState as phyAiuAdminState | |||
| TruthValue as phyAiuRebootRr | |||
| PhyMcuEntry | |||
| SEQUENCE | |||
| INTEGER as phyMcuIndex | |||
| CardOpState as phyMcuOpState | |||
| CardFaultLed as phyMcuFaultLed | |||
| CardTempStatus as phyMcuTempStatus | |||
| CardVoltageStatus as phyMcuVoltageStatus | |||
| DisplayString as phyMcuSerialNumber | |||
| DisplayString as phyMcuProductionDate | |||
| DisplayString as phyMcuPartNumber | |||
| DisplayString as phyMcuDescription | |||
| DisplayString as phyMcuHardwareVersion | |||
| DisplayString as phyMcuIpmiSwVersion | |||
| DisplayString as phyMcuAssemblyId | |||
| AssemblyIdSource as phyMcuAssemblyIdSrc | |||
| TruthValue as phyMcuExcessiveFakeAid | |||
| AdminState as phyMcuAdminState | |||
| DisplayString as phyCpldVersion | |||
| PhyBbuEntry | |||
| SEQUENCE | |||
| INTEGER as phyBbuIndex | |||
| CardOpState as phyBbuOpState | |||
| CardFaultLed as phyBbuFaultLed | |||
| CardTempStatus as phyBbuTempStatus | |||
| CardVoltageStatus as phyBbuVoltageStatus | |||
| DisplayString as phyBbuSerialNumber | |||
| DisplayString as phyBbuProductionDate | |||
| DisplayString as phyBbuPartNumber | |||
| DisplayString as phyBbuDescription | |||
| DisplayString as phyBbuHardwareVersion | |||
| DisplayString as phyBbuIpmiSwVersion | |||
| DisplayString as phyBbuAssemblyId | |||
| AssemblyIdSource as phyBbuAssemblyIdSrc | |||
| TruthValue as phyBbuExcessiveFakeAid | |||
| AdminState as phyBbuAdminState | |||
| PhyRxuEntry | |||
| SEQUENCE | |||
| INTEGER as phyRxuIndex | |||
| CardOpState as phyRxuOpState | |||
| CardFaultLed as phyRxuFaultLed | |||
| CardTempStatus as phyRxuTempStatus | |||
| CardVoltageStatus as phyRxuVoltageStatus | |||
| DisplayString as phyRxuSerialNumber | |||
| DisplayString as phyRxuProductionDate | |||
| DisplayString as phyRxuPartNumber | |||
| DisplayString as phyRxuDescription | |||
| DisplayString as phyRxuHardwareVersion | |||
| DisplayString as phyRxuIpmiSwVersion | |||
| DisplayString as phyRxuAssemblyId | |||
| AssemblyIdSource as phyRxuAssemblyIdSrc | |||
| TruthValue as phyRxuExcessiveFakeAid | |||
| AdminState as phyRxuAdminState | |||
| RfBand as phyRxuRfBand | |||
| PhyTxuEntry | |||
| SEQUENCE | |||
| INTEGER as phyTxuIndex | |||
| CardOpState as phyTxuOpState | |||
| CardFaultLed as phyTxuFaultLed | |||
| CardTempStatus as phyTxuTempStatus | |||
| CardVoltageStatus as phyTxuVoltageStatus | |||
| DisplayString as phyTxuSerialNumber | |||
| DisplayString as phyTxuProductionDate | |||
| DisplayString as phyTxuPartNumber | |||
| DisplayString as phyTxuDescription | |||
| DisplayString as phyTxuHardwareVersion | |||
| DisplayString as phyTxuIpmiSwVersion | |||
| DisplayString as phyTxuAssemblyId | |||
| AssemblyIdSource as phyTxuAssemblyIdSrc | |||
| TruthValue as phyTxuExcessiveFakeAid | |||
| AdminState as phyTxuAdminState | |||
| RfBand as phyTxuRfBand | |||
| PaEntry | |||
| SEQUENCE | |||
| INTEGER as paIndex | |||
| AdminState as paAdminState | |||
| CardOpState as paOpState | |||
| CardTempStatus as paTempStatus | |||
| FloatAsString as paOutputTxPower | |||
| FloatAsString as paInputTxPower | |||
| FloatAsString as paTxReflectedPower | |||
| TruthValue as paDcPowerFault | |||
| TruthValue as paRfOverdriveFault | |||
| TruthValue as paFeedForwardFault | |||
| DisplayString as paSerialNumber | |||
| RfBand as paRfBand | |||
| DisplayString as paHardwareVersion | |||
| INTEGER as paTemperature | |||
| TruthValue as paReflectedPowerFault | |||
| TruthValue as paUnderPowerFault | |||
| FloatAsString as paTargetOutputTxPower | |||
| PaState as paOperStatus | |||
| PaRfBand as paRadioFreqBand | |||
| PaPowerEntry | |||
| SEQUENCE | |||
| INTEGER as paPowerIndex | |||
| INTEGER as paPowerTxOutput | |||
| INTEGER as paPowerTxInput | |||
| INTEGER as paPowerTxReflected | |||
| BbuSysEntry | |||
| SEQUENCE | |||
| INTEGER as bbuSysId | |||
| DisplayString as bbuDspVer | |||
| DisplayString as bbuLlcVer | |||
| DisplayString as bbuTxFpgaVer | |||
| DisplayString as bbuRxFpgaVer | |||
| Unsigned32 as bbuLdpcVer | |||
| INTEGER as bbuRfChanNum | |||
| INTEGER as bbuExtGainTx | |||
| INTEGER as bbuExtGainRx | |||
| INTEGER as bbuRfGainRx0 | |||
| INTEGER as bbuRfGainRx1 | |||
| INTEGER as bbuRfBand | |||
| INTEGER as bbuRfPowerTx0 | |||
| INTEGER as bbuRfPowerTx1 | |||
| INTEGER as bbuRfuEnableMask | |||
| FloatAsString as bbuExtTxGain | |||
| FloatAsString as bbuExtRxGain | |||
| FloatAsString as bbuRfRx0Gain | |||
| FloatAsString as bbuRfRx1Gain | |||
| FloatAsString as bbuRfTx0Power | |||
| FloatAsString as bbuRfTx1Power | |||
| INTEGER as bbuTxPwrDeviationLimit | |||
| INTEGER as bbuSlope | |||
| INTEGER as bbuMcastSnr | |||
| INTEGER as bbuScmType | |||
| INTEGER as bbuSleepInactivityTimer | |||
| INTEGER as bbuLuTimer | |||