FLOWPOINT-MIB

File: FLOWPOINT-MIB.mib (195307 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212

Imported symbols

NetworkAddress IpAddress Counter
Gauge enterprises DisplayString
OBJECT-TYPE

Defined Objects

flowpoint 1.3.6.1.4.1.1548
OBJECT IDENTIFIER    

fpdod 1.3.6.1.4.1.1548.1
OBJECT IDENTIFIER    

dodTable 1.3.6.1.4.1.1548.1.1
The DOD basic configuration table for each remote connection. All of the DOD tables are indexed (identified) by DestinationName.
OBJECT-TYPE    
  SEQUENCE OF  
    DodEntry

dodEntry 1.3.6.1.4.1.1548.1.1.1
OBJECT-TYPE    
  DodEntry  

dodTableID 1.3.6.1.4.1.1548.1.1.1.1
The identifier number of this remote name. Each dod table will have a unique identifier number for it. The ID number is issued when the dod table of the destination name is created on the agent side. This object is obsoleted: use dodDestinationName as the index.
OBJECT-TYPE    
  INTEGER  

dodDestinationName 1.3.6.1.4.1.1548.1.1.1.2
A textual description of the remote destination. The name is given by the manager side when the manager uses object dodTableOperation to create a new Dod record. The dodDestination is important. It will be used throughout all of the Dod database as index to access each object.
OBJECT-TYPE    
  DisplayString SIZE(0..20)  

dodPassword 1.3.6.1.4.1.1548.1.1.1.3
The password for this remote connection. It is used to check the remote's password when the remote client or server dials in. It is also used when authentication is enabled during outgoing calls. GENERR is returned if not authorized to read the dodPassword.
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

dodAuthenProtocol 1.3.6.1.4.1.1548.1.1.1.4
The minimum authentication protocol this remote connection is using. It is one of CHAP or PAP or NONE. The actual authentication phase can be performed with a better protocol than specified here: for instance if set to PAP and the remote supports CHAP (as negotiated during the LCP phase), CHAP authentication will be performed. None means that authentication of this remote is disabled during outgoing calls. All incoming calls are ALWAYS authenticated, so setting this to none prevents from accepting incoming calls.
OBJECT-TYPE    
  AuthenProtoType  


dodBWThreshold 1.3.6.1.4.1.1548.1.1.1.6
The threshold of bandwidth utilization of established links used to trigger an additional call, expressed as an integer percentage, i.e. 0 to 100. 0 means that all available links are dialed at once while 100 means that no additional links are used. The type of bandwidth measured by this object is defined by dodBODType.
OBJECT-TYPE    
  INTEGER 0..100  

dodPreferType 1.3.6.1.4.1.1548.1.1.1.7
The preferred line connection type.
OBJECT-TYPE    
  ConnectionType  

dodTearDownTimer 1.3.6.1.4.1.1548.1.1.1.8
The timeout limit to tear down the link when there is no activity for the link, expressed in seconds.
OBJECT-TYPE    
  INTEGER  

dodSourceIPAddress 1.3.6.1.4.1.1548.1.1.1.9
The local IP address of the WAN port. It is used to negotiate with the remote side when dialing in or out. When nonzero, it overrides the default address, coming from the LAN port IP address (ethernet).
OBJECT-TYPE    
  IpAddress  

dodRemoteIPAddress 1.3.6.1.4.1.1548.1.1.1.10
The remote IP address of the WAN port, if needed. Set to 0 otherwise.
OBJECT-TYPE    
  IpAddress  

dodSourceIPMask 1.3.6.1.4.1.1548.1.1.1.11
The local IP net mask of the WAN port. It is used with dodSourceIPAddress.
OBJECT-TYPE    
  IpAddress  

dodRemoteIPMask 1.3.6.1.4.1.1548.1.1.1.12
The remote side IP network mask.
OBJECT-TYPE    
  IpAddress  

dodIPXNetAddress 1.3.6.1.4.1.1548.1.1.1.13
The IPX network address associated with the WAN link when connected to this remote.
OBJECT-TYPE    
  IpxNetAddress  

dodIPFilters 1.3.6.1.4.1.1548.1.1.1.14
Number of IP filters currently defined for this remote.
OBJECT-TYPE    
  Counter  

dodIPXFilters 1.3.6.1.4.1.1548.1.1.1.15
Number of IPX filters currently defined for this remote
OBJECT-TYPE    
  Counter  

dodRemoteIPNets 1.3.6.1.4.1.1548.1.1.1.16
This object describes the number of static IP routing entries for this destination name or connection. The static IP routing table is defined in another group.
OBJECT-TYPE    
  Counter  

dodRemoteIPXNets 1.3.6.1.4.1.1548.1.1.1.17
This object describes the number of static IPX routing entries for this destination. The static IPX routing table is defined in another group.
OBJECT-TYPE    
  Counter  

dodRemoteIPXSAPs 1.3.6.1.4.1.1548.1.1.1.18
This object describes the number of static IPX SAP entries for this destination. The static IPX SAP table is defined in another group.
OBJECT-TYPE    
  Counter  

dodRemoteMacState 1.3.6.1.4.1.1548.1.1.1.19
This object controls the current bridge state (enabled or disabled) for this destination. When one of the remote destinations is turned on, the LAN port (ethernet) bridge capability will be turned on also, after a reboot. If this destination's bridge state is disabled and the bridge state of all the other destinations is also disabled, the LAN port bridge state will be disabled. Otherwise, if another destination's bridge state is still enabled, the LAN port bridge state will stay enabled. This mechanism is implemented in the system.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodRemoteMacs 1.3.6.1.4.1.1548.1.1.1.20
The number of specific MAC addresses defined to be statically bridged to this remote.
OBJECT-TYPE    
  Counter  

dodLastActivityTime 1.3.6.1.4.1.1548.1.1.1.21
The last activity time with this destination
OBJECT-TYPE    
  INTEGER  

dodTableOperation 1.3.6.1.4.1.1548.1.1.1.22
This object is used to create a new DOD record or to delete a DOD record.
OBJECT-TYPE    
  INTEGER add(1), remove(2)  


dodBODType 1.3.6.1.4.1.1548.1.1.1.24
The type of traffic to which bandwidth measurement (defined by dodBWThreshold) applies.
OBJECT-TYPE    
  INTEGER both(1), output(2), input(3)  

dodIpOptRecvRIP 1.3.6.1.4.1.1548.1.1.1.25
Allows processing of RIP packets received from this destination, when connected and IP routing is enabled in a RIP 1 compatible manner. dodIpOptRecvRIP, dodIpOptRecvRIP1, and dodIpOptRecvRIP2 are mutually exclusive.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodIpOptSendRIP 1.3.6.1.4.1.1548.1.1.1.26
Allows sending of RIP packets to this destination when connected and IP routing is enabled in a RIP 1 compatible manner. dodIpOptSendRIP, dodIpOptSendRIP1, and dodIpOptSendRIP2 are mutually exclusive.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodIpOptRecvRIPDefault 1.3.6.1.4.1.1548.1.1.1.27
Allows updating of the IP default route when receiving a RIP packet from this destination for the route 0.0.0.0.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodIpOptSendRIPDefault 1.3.6.1.4.1.1548.1.1.1.28
Allows sending of the IP default route (if known) to this destination when connected, as 0.0.0.0.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodIpOptKeepPrivate 1.3.6.1.4.1.1548.1.1.1.29
Allows to keep the route to this destination private, i.e. don't advertise it to other destinations
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodBrOptUseStp 1.3.6.1.4.1.1548.1.1.1.30
Allows use of Bridging Spanning Tree Protocol when connected to this destination (causes a 40 second startup delay): use when topology loops are likely.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodPPPOptUseLCPEcho 1.3.6.1.4.1.1548.1.1.1.31
Perform a PPP LCP Echo request at regular intervals when connected to this destination.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodEntryIsDisabled 1.3.6.1.4.1.1548.1.1.1.32
This database entry is active (enabled) or temporarily disabled (i.e. bypassed when searching the database). This eliminates the need for constant add/removes.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

dodCallbackOption 1.3.6.1.4.1.1548.1.1.1.33
This option defines under what circumstances this system is allowed to dial the specified remote. The setting 'enable' means that this system is free to call the specified remote on its own and also to dial it back. Under the 'disable' setting, dialing back is never a possibility, but this system can dial the remote on its own if a phone number exists for it. The 'callback-only' setting prevents this system from calling the remote on its own: it will only perform the dial-back service. Note: in order to implement dial-back, Caller entries for this remote must exist (in dodCallerTable). This allows this system to identify what remote is calling, locating its database information and possibly calling it back. Caller Id verification (in fpSysCallerIdTable) is independent but uses the same dodCallerTable information.
OBJECT-TYPE    
  INTEGER enable(1), disable(2), callback-only(3)  

dodSendDataAsVoice 1.3.6.1.4.1.1548.1.1.1.34
This option determines whether ISDN data calls issued to this remote should be generated as voice calls instead of restricted or unrestricted digital (ISDN only).
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodIPXNetStrAddress 1.3.6.1.4.1.1548.1.1.1.35
The IPX network address associated with the WAN link when connected to this remote. This is an alternative to the dodIPXNetAddress object to be used when OCTET STRINGs are not implemented. In this case, specify the IPX network number as an ASCII string containing from 1 to 8 characters, to be converted to hexadecimal by the firmware.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

dodOurSystemName 1.3.6.1.4.1.1548.1.1.1.36
Our system name (also called user name) when initiating a communication with this remote. It is used to override the global system name (fpSysName) and is useful when the name was assigned by the remote system admin, not by this system admin, in order to avoid using the same name (not under our control) for all connections.
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

dodOurPassword 1.3.6.1.4.1.1548.1.1.1.37
Our system password when initiating a communication with this remote. It is used to override the global system password (when not empty) and is useful when the password was assigned by the remote system admin, not by this system admin, in order to avoid using the same password (not under our control) for all connections. GENERR is returned if not authorized to read the dodOurPassword.
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

dodPPPCallbackOption 1.3.6.1.4.1.1548.1.1.1.38
This option defines under what circumstances this system is requesting a callback by using a method within the PPP protocol suite (as opposed to an ISDN callback). The possibilities are: - don't do any PPP callback (none) - ask the peer to us back based on the database record that he has for us (authentication). - supply the string (i.e. phone number, including prefixes etc,...) that the peer should use to call us back. - supply a location information which the peer will use in addition to our user name to call us back. - supply a E.164 string to the peer to call us back. - supply a generic string (name-string) to the peer so that it can use to it call us back using whatever method it deems appropriate. This router will force this to be the same as the remote name (index in the remote database) if it receives such a string.
OBJECT-TYPE    
  INTEGER none(1), authentication(2), dial-string(3), location-string(4), e164-string(5), name-string(6)  

dodPPPCallbackInfo 1.3.6.1.4.1.1548.1.1.1.39
When the dodPPPCallbackOption is set to something other than none(1), this fields contains the additional information sent to the PPP peer when requested a callback.
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

dodDontAuthenticate 1.3.6.1.4.1.1548.1.1.1.40
When enabled (1), do not request any authentication protocol when dialing out this destination. Note that an incoming call from this remote still requires some form of authentication (to find this remote entry record), as the key to the record is the authenticated name.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodIPAddressTranslation 1.3.6.1.4.1.1548.1.1.1.41
When enabled (1), do IP address translation for traffic to/from this remote.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodIpOptRecvRIP1 1.3.6.1.4.1.1548.1.1.1.42
Allows processing of RIP packets received from this destination, when connected and IP routing is enabled using RIP 1 only. dodIpOptRecvRIP, dodIpOptRecvRIP1, and dodIpOptRecvRIP2 are mutually exclusive.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodIpOptSendRIP1 1.3.6.1.4.1.1548.1.1.1.43
Allows sending of RIP packets to this destination when connected and IP routing is enabled using RIP 1 only. dodIpOptSendRIP, dodIpOptSendRIP1, and dodIpOptSendRIP2 are mutually exclusive.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodIpOptRecvRIP2 1.3.6.1.4.1.1548.1.1.1.44
Allows processing of RIP packets received from this destination, when connected and IP routing is enabled using RIP 2 only. dodIpOptRecvRIP, dodIpOptRecvRIP1, and dodIpOptRecvRIP2 are mutually exclusive.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodIpOptSendRIP2 1.3.6.1.4.1.1548.1.1.1.45
Allows sending of RIP packets to this destination when connected and IP routing is enabled using RIP 2 only. dodIpOptSendRIP, dodIpOptSendRIP1, and dodIpOptSendRIP2 are mutually exclusive.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodProtocol 1.3.6.1.4.1.1548.1.1.1.46
Type of protocol used for communicating with this remote.
OBJECT-TYPE    
  INTEGER protocolppp(1), protocol1483pppllc(2), protocol1483snap(3), protocol1483snapmer(4), protocol1483snapfr(5), protocolrawip(6)  

dodCompression 1.3.6.1.4.1.1548.1.1.1.47
When enabled (1), do compression for traffic to/from this remote.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodPasswordSpecified 1.3.6.1.4.1.1548.1.1.1.48
Return true if the password for this remote connection has been specified.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

dodOurPasswordSpecified 1.3.6.1.4.1.1548.1.1.1.49
Return true if our system password for this remote connnection has been specified.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

dodBlockNetBIOS 1.3.6.1.4.1.1548.1.1.1.50
When enabled (1), block NetBIOS traffic to this remote.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodMtu 1.3.6.1.4.1.1548.1.1.1.51
When non-zero, the desired MTU size for this remote. When zero, use the default MTU size for the interface. The MTU size used is the minimum of the desired MTU size for this remote and the maximum MTU size allowed for the interface.
OBJECT-TYPE    
  INTEGER  

dodIpSlaveMode 1.3.6.1.4.1.1548.1.1.1.52
When enabled (1), always accept peer proposal for our IP address for our WAN interface.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodReacquireIpAddr 1.3.6.1.4.1.1548.1.1.1.53
When enabled (1), try to reacquire the last used IP address for this interface IF we believe any TCP connections are still active to this remote.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodIpxOptRIPSAP 1.3.6.1.4.1.1548.1.1.1.54
When enabled (1), allows IPXCP to negotiate the use of RIP and SAP IPX traffic. Actual use of the RIP and SAP protocols will depend on the capabilities of the remote at the time the PPP connection is established.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dodCallIDTable 1.3.6.1.4.1.1548.1.2
A list of Call identifiers (phone number, DLCI ....) for a particular destination name and link type (ISDN). This table includes only two entries, type and phone number count.
OBJECT-TYPE    
  SEQUENCE OF  
    DodCallIDEntry

dodCallIDEntry 1.3.6.1.4.1.1548.1.2.1
An entry of Call identifier for each connection type.
OBJECT-TYPE    
  DodCallIDEntry  

dodCallIDType 1.3.6.1.4.1.1548.1.2.1.1
The connection type.
OBJECT-TYPE    
  ConnectionType  

dodCallIDPhones 1.3.6.1.4.1.1548.1.2.1.2
Number of entries in the dodPhoneTable for this type of connection and this remote.
OBJECT-TYPE    
  Counter  

dodPhoneTable 1.3.6.1.4.1.1548.1.3
OBJECT-TYPE    
  SEQUENCE OF  
    DodPhoneEntry

dodPhoneEntry 1.3.6.1.4.1.1548.1.3.1
OBJECT-TYPE    
  DodPhoneEntry  

dodPhoneIndex 1.3.6.1.4.1.1548.1.3.1.1
It is an index to recognize which phone number is in the table with the specified CallIDType and DestinationName.
OBJECT-TYPE    
  INTEGER 1..2  

dodPhoneSpeed 1.3.6.1.4.1.1548.1.3.1.2
The line speed (in bits per seconds) for asynchronous connections.
OBJECT-TYPE    
  INTEGER  

dodPhoneNumber 1.3.6.1.4.1.1548.1.3.1.3
The phone number string.
OBJECT-TYPE    
  DisplayString SIZE(0..30)  

dodRemoteMacTable 1.3.6.1.4.1.1548.1.4
A table of MAC addresses for bridging of the specified destination name. The table is indexed by destination name and MAC address.
OBJECT-TYPE    
  SEQUENCE OF  
    DodRemoteMacEntry

dodRemoteMacEntry 1.3.6.1.4.1.1548.1.4.1
OBJECT-TYPE    
  DodRemoteMacEntry  

dodRemoteMacIndex 1.3.6.1.4.1.1548.1.4.1.1
The index number is not used currently. User don't need to implement it currently. The table is indexed by the MAC address.
OBJECT-TYPE    
  INTEGER  

dodRemoteMacAddress 1.3.6.1.4.1.1548.1.4.1.2
Contains the IEEE unique MAC address of statically configured devices for bridging purposes. When all of the 6 bytes of this MAC address are zero, the entry is called the unknown address. Any packet with a destination address not in the static or dynamic MAC table of any remote bridge will be sent to the default remote bridge (which has a dodRemoteMacAddress entry defined for the unknown MAC address).. There can be only one remote destination specified as default bridge, i.e. containing the unknown MAC address.
OBJECT-TYPE    
  MacAddress  

dodRemoteMacOperation 1.3.6.1.4.1.1548.1.4.1.3
add -- add a static MAC address to be bridge to this remote destination. remove -- remove a static MAC address.
OBJECT-TYPE    
  INTEGER add(1), remove(2)  

dodRemoteIPNetTable 1.3.6.1.4.1.1548.1.5
The static IP routing table. It is based on indexes of destination name and IP net address.
OBJECT-TYPE    
  SEQUENCE OF  
    DodRemoteIPNetEntry

dodRemoteIPNetEntry 1.3.6.1.4.1.1548.1.5.1
OBJECT-TYPE    
  DodRemoteIPNetEntry  

dodRemoteIPNetIndex 1.3.6.1.4.1.1548.1.5.1.1
This index is not currently in use.
OBJECT-TYPE    
  INTEGER  

dodRemoteIPNetAddress 1.3.6.1.4.1.1548.1.5.1.2
The IP network address of an entry of the static IP routing table.
OBJECT-TYPE    
  IpAddress  

dodRemoteIPNetMask 1.3.6.1.4.1.1548.1.5.1.3
The IP network mask of an entry of the static IP routing table.
OBJECT-TYPE    
  IpAddress  

dodRemoteIPNetHops 1.3.6.1.4.1.1548.1.5.1.4
The hop count for the specified IP network address and destination name.
OBJECT-TYPE    
  INTEGER 1..15  

dodRemoteIPNetOperation 1.3.6.1.4.1.1548.1.5.1.5
add -- add a static IP route to this destination. remove -- delete a static IP route to this destination. To access the other objects in this entry (mask, hops) the SNMP manager should add an entry first and then set those other objects.
OBJECT-TYPE    
  INTEGER add(1), remove(2)  

dodRemoteIPNetGateway 1.3.6.1.4.1.1548.1.5.1.6
The IP address of the gateway to which packets are sent when the static route is over a broadcast medium, such as when dodProtocol is RFC1483 with Mac Encapsulated Routing. When the medium is point-to-point, this field is ignored.
OBJECT-TYPE    
  IpAddress  

dodRemoteIPXNetTable 1.3.6.1.4.1.1548.1.6
The static IPX routing table. It is based on indexes of destination name and IPX network number.
OBJECT-TYPE    
  SEQUENCE OF  
    DodRemoteIPXNetEntry

dodRemoteIPXNetEntry 1.3.6.1.4.1.1548.1.6.1
OBJECT-TYPE    
  DodRemoteIPXNetEntry  

dodRemoteIPXNetIndex 1.3.6.1.4.1.1548.1.6.1.1
Use dodRemoteIPXNetAddress as the index.
OBJECT-TYPE    
  INTEGER  

dodRemoteIPXNetAddress 1.3.6.1.4.1.1548.1.6.1.2
The IPX network address of an entry of the static IPX routing table.
OBJECT-TYPE    
  IpxNetAddress  

dodRemoteIPXNetMetric 1.3.6.1.4.1.1548.1.6.1.3
The number of hops to reach this IPX network (via this destination).
OBJECT-TYPE    
  INTEGER 1..15  

dodRemoteIPXNetTicks 1.3.6.1.4.1.1548.1.6.1.4
Number of 1/18th of seconds ticks necessary to reach this IPX network number (via this destination).
OBJECT-TYPE    
  INTEGER  

dodRemoteIPXNetOperation 1.3.6.1.4.1.1548.1.6.1.5
add -- add a static IPX route to this destination remove -- delete a static IPX route for this destination For IPX metric and ticks, the SNMP manager should create the entry first and then set those attributes.
OBJECT-TYPE    
  INTEGER add(1), remove(2)  

dodRemoteIPXNetStrAddress 1.3.6.1.4.1.1548.1.6.1.6
The IPX network address of an entry of the static IPX routing table. This is an alternative to the dodRemoteIPXNetAddress object to be used when OCTET STRINGs are not implemented. In this case, specify the IPX network number as an ASCII string containing from 1 to 8 characters, to be converted to hexadecimal by the firmware.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

dodRemoteIPXSAPTable 1.3.6.1.4.1.1548.1.7
The remote IPX SAP table. It is based on indexes of DOD destination name, IPX network address, IPX node number, and IPX socket number.
OBJECT-TYPE    
  SEQUENCE OF  
    DodRemoteIPXSAPEntry

dodRemoteIPXSAPEntry 1.3.6.1.4.1.1548.1.7.1
OBJECT-TYPE    
  DodRemoteIPXSAPEntry  

dodRemoteIPXSAPIndex 1.3.6.1.4.1.1548.1.7.1.1
Use dodRemoteIPXSAPNetAddress, dodRemoteIPXSAPNodeAddress dodRemoteIPXSAPSocket as indexes. Not used.
OBJECT-TYPE    
  INTEGER  

dodRemoteIPXSAPName 1.3.6.1.4.1.1548.1.7.1.2
The name by which this IPX service is known.
OBJECT-TYPE    
  DisplayString SIZE(0..48)  

dodRemoteIPXSAPNetAddress 1.3.6.1.4.1.1548.1.7.1.3
The internal IPX network number of the server providing this particular IPX service.
OBJECT-TYPE    
  IpxNetAddress  

dodRemoteIPXSAPNodeAddress 1.3.6.1.4.1.1548.1.7.1.4
The node address on the IPX network number on which a server provides this particular IPX service.
OBJECT-TYPE    
  MacAddress  

dodRemoteIPXSAPSocket 1.3.6.1.4.1.1548.1.7.1.5
The socket (i.e. internal port number) at which the specified IPX service is provided in the server.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

dodRemoteIPXSAPType 1.3.6.1.4.1.1548.1.7.1.6
The well-known type of service (i.e. File Service, Advertising Print Service, etc...)
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

dodRemoteIPXSAPHops 1.3.6.1.4.1.1548.1.7.1.7
The number of hops necessary to reach the provider of this service.
OBJECT-TYPE    
  INTEGER 1..15  

dodRemoteIPXSAPOperation 1.3.6.1.4.1.1548.1.7.1.9
add -- add a new IPX SAP service to this destination remove -- delete an IPX SAP service from this destination For the IPX network address, node address, socket number, type and hops, the SNMP manager should set those after creating the entry.
OBJECT-TYPE    
  INTEGER add(1), remove(2)  

dodRemoteIPXSAPStrNetAddress 1.3.6.1.4.1.1548.1.7.1.10
The internal IPX network number of the server providing this particular IPX service, expressed as an ASCII string, converted to hexadecimal by the firmware.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

dodRemoteIPXSAPStrSocket 1.3.6.1.4.1.1548.1.7.1.11
The socket (i.e. internal port number) at which the specified IPX service is provided in the server, expressed as an ASCII string, converted to hexadecimal by the firmware.
OBJECT-TYPE    
  DisplayString SIZE(1..4)  

dodRemoteIPXSAPStrType 1.3.6.1.4.1.1548.1.7.1.12
The well-known type of service (i.e. File Service, Advertising Print Service, etc...), expressed as an ASCII string, converted to hexadecimal by the firmware.
OBJECT-TYPE    
  DisplayString SIZE(1..4)  

dodIPFilterTable 1.3.6.1.4.1.1548.1.8
A set of IP filters defined for this remote.
OBJECT-TYPE    
  SEQUENCE OF  
    DodIPFilterEntry

dodIPFilterEntry 1.3.6.1.4.1.1548.1.8.1
OBJECT-TYPE    
  DodIPFilterEntry  

dodIPFilterIndex 1.3.6.1.4.1.1548.1.8.1.1
OBJECT-TYPE    
  INTEGER 1..65536  

dodIPFilterDstNetAddr 1.3.6.1.4.1.1548.1.8.1.2
OBJECT-TYPE    
  IpAddress  

dodIPFilterSrcNetAddr 1.3.6.1.4.1.1548.1.8.1.3
OBJECT-TYPE    
  IpAddress  

dodIPFilterAllow 1.3.6.1.4.1.1548.1.8.1.4
OBJECT-TYPE    
  INTEGER allow(1), deny(2)  

dodIPXFilterTable 1.3.6.1.4.1.1548.1.9
A set of IPX filters defined for this remote.
OBJECT-TYPE    
  SEQUENCE OF  
    DodIPXFilterEntry

dodIPXFilterEntry 1.3.6.1.4.1.1548.1.9.1
OBJECT-TYPE    
  DodIPXFilterEntry  

dodIPXFilterIndex 1.3.6.1.4.1.1548.1.9.1.1
OBJECT-TYPE    
  INTEGER 1..65536  

dodIPXFilterDstNetAddr 1.3.6.1.4.1.1548.1.9.1.2
OBJECT-TYPE    
  IpxNetAddress  

dodIPXFilterDstNodeAddr 1.3.6.1.4.1.1548.1.9.1.3
OBJECT-TYPE    
  MacAddress  

dodIPXFilterDstSocket 1.3.6.1.4.1.1548.1.9.1.4
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

dodIPXFilterSrcNetAddr 1.3.6.1.4.1.1548.1.9.1.5
OBJECT-TYPE    
  IpxNetAddress  

dodIPXFilterSrcNodeAddr 1.3.6.1.4.1.1548.1.9.1.6
OBJECT-TYPE    
  MacAddress  

dodIPXFilterSrcSocket 1.3.6.1.4.1.1548.1.9.1.7
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

dodIPXFilterAllow 1.3.6.1.4.1.1548.1.9.1.8
OBJECT-TYPE    
  INTEGER allow(1), deny(2)  

dodOperation 1.3.6.1.4.1.1548.1.10
Use this object to give commands to save, load or erase DOD configuration in FLASH memory.
OBJECT-TYPE    
  INTEGER save(1), load(2), erase(3)  

dodRemoteMacDefault 1.3.6.1.4.1.1548.1.11
for GET : This object gives the remote destination name of default bridge. for SET : To set new default bridge, just give the the desired destination name. To delete and disable existing default bridge, just give a NULL string.
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

dodCallerTable 1.3.6.1.4.1.1548.1.12
The Caller table: this is the list of numbers to search when receiving an incoming call, to identify the remote peer which made that call and thus find the corresponding dodEntry record. This table is used to implement dial-back and also to implement Caller ID verification (i.e. denying access to an unknown caller).
OBJECT-TYPE    
  SEQUENCE OF  
    DodCallerEntry

dodCallerEntry 1.3.6.1.4.1.1548.1.12.1
Telephone numbers (or call information) of potential callers.
OBJECT-TYPE    
  DodCallerEntry  

dodCallerNumber 1.3.6.1.4.1.1548.1.12.1.1
The number against which caller ID verification takes place or used to find out which peer is calling before dial-back takes place.
OBJECT-TYPE    
  DisplayString SIZE(0..30)  

dodCallerOperation 1.3.6.1.4.1.1548.1.12.1.2
The operation being performed on a Caller data set: add or remove an entry for the specified remote and connection type.
OBJECT-TYPE    
  INTEGER add(1), remove(2)  

dodIPTranslationServerTable 1.3.6.1.4.1.1548.1.13
The IP Translation Server Table. Used to select a server when doing IP address translation.
OBJECT-TYPE    
  SEQUENCE OF  
    DodIPTranslationServerEntry

dodIPTranslationServerEntry 1.3.6.1.4.1.1548.1.13.1
OBJECT-TYPE    
  DodIPTranslationServerEntry  

dodIPTranslationServerIPAddress 1.3.6.1.4.1.1548.1.13.1.1
The IP address of the Server when doing IP Address translation.
OBJECT-TYPE    
  IpAddress  

dodIPTranslationProtocol 1.3.6.1.4.1.1548.1.13.1.2
The protocol used by this Server.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

dodIPFirstTranslationPort 1.3.6.1.4.1.1548.1.13.1.3
First public port in range used by this server. This port is what is referenced by the client. A port of 0 is a wild-card signifying any port.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

dodIPLastTranslationPort 1.3.6.1.4.1.1548.1.13.1.4
Last public port in range used by this server. This port is the last port in range and is referenced by the client.. This value must be greater than or equal first public port in range.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

dodIPFirstPrivatePort 1.3.6.1.4.1.1548.1.13.1.5
This is the first private port in range as seen by the server. The public port range is mapped to this private port range. If the public port range is to be the same as the private port range, this port should be the same as the first public port.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

dodIPTranslationStatus 1.3.6.1.4.1.1548.1.13.1.6
The status column used for creating, modifying, and deleting instances of the columnar objects in this table.
OBJECT-TYPE    
  RowStatus  

dodNatHostMappingTable 1.3.6.1.4.1.1548.1.14
The NAT Host Mapping Table. Used to select a NAT Host Mapping when doing IP address translation.
OBJECT-TYPE    
  SEQUENCE OF  
    DodNatHostMappingEntry

dodNatHostMappingEntry 1.3.6.1.4.1.1548.1.14.1
OBJECT-TYPE    
  DodNatHostMappingEntry  

dodFirstPrivateIPAddress 1.3.6.1.4.1.1548.1.14.1.1
The first private IP address which starts the range of private IP addresses which are mapped to public IP addresses.
OBJECT-TYPE    
  IpAddress  

dodLastPrivateIPAddress 1.3.6.1.4.1.1548.1.14.1.2
The last private IP address which ends the range of private IP addresses which are mapped to public IP addresses.
OBJECT-TYPE    
  IpAddress  

dodFirstPublicIPAddress 1.3.6.1.4.1.1548.1.14.1.3
The first public IP address which starts the range of public IP Addresses which are mapped to private IP addresses. The last public IP address in the range is calculated by counting the number of private IP addresses in the private IP address range and creating an equivalent number of IP addresses in the public IP address range so there is a one to one mapping of public IP addresses to private IP addresses.
OBJECT-TYPE    
  IpAddress  

dodNatHostMappingStatus 1.3.6.1.4.1.1548.1.14.1.4
The status column used for creating, modifying, and deleting instances of the columnar objects in this table.
OBJECT-TYPE    
  RowStatus  

fpether 1.3.6.1.4.1.1548.2
OBJECT IDENTIFIER    

fpEtherTable 1.3.6.1.4.1.1548.2.1
The Ethernet interface configuration table for each port
OBJECT-TYPE    
  SEQUENCE OF  
    FpEtherEntry

fpEtherEntry 1.3.6.1.4.1.1548.2.1.1
OBJECT-TYPE    
  FpEtherEntry  

fpPortNum 1.3.6.1.4.1.1548.2.1.1.1
The identifier number of this interface port.
OBJECT-TYPE    
  INTEGER 1..2  

fpBridgeState 1.3.6.1.4.1.1548.2.1.1.2
The object is used to show current state (enabled/ disabled) of the bridging the LAN port (ethernet). 1 -- the bridging is enabled. 2 -- the bridging is disabled. The bridging is enabled/disabled by controlling the dodRemoteMacState object of all the destinations. This field is only writeable on systems that don't support remote destinations (the DOD table).
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpIpState 1.3.6.1.4.1.1548.2.1.1.3
Determines whether the IP protocol is routed (enable) or not (disable) via this LAN interface. A change requires rebooting. If the IP address and the network mask are defined and IP routing is not enabled, this system acts as an IP host only.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpIpxState 1.3.6.1.4.1.1548.2.1.1.4
Determines whether the IPX protocol is routed (enable) or not (disable) via this LAN interface. A change requires rebooting.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpIpNetAddress 1.3.6.1.4.1.1548.2.1.1.5
This object allows to get or set the IP address for this LAN interface: a change requires rebooting.
OBJECT-TYPE    
  IpAddress  

fpIpNetMask 1.3.6.1.4.1.1548.2.1.1.6
This object allows to get or set the IP network mask for this LAN interface: a change requires rebooting.
OBJECT-TYPE    
  IpAddress  

fpIpxNetAddress 1.3.6.1.4.1.1548.2.1.1.7
This objects allows to get or set the IPX external network number for this LAN port: a change requires rebooting.
OBJECT-TYPE    
  IpxNetAddress  

fpIpxFrameType 1.3.6.1.4.1.1548.2.1.1.8
This objects allows to get or set the IPX frame type generated by the router for this LAN port: a change requires rebooting. Possible values are: 802.2 (using the Novell SAP 0xE0), 802.3 (the IPX packet follows the Ethernet header immediately with no type) and Ethernet-II (named DIX) where the Ethertype is 0x8137.
OBJECT-TYPE    
  INTEGER frame-8022(1), frame-8023(2), frame-dix(3)  

fpEtherIpOptRecvRIP 1.3.6.1.4.1.1548.2.1.1.9
Allows the processing of IP RIP 1 and RIP 2 packets received from for this LAN port: a change requires rebooting. This setting is enabled by default. fpEtherIpOptRecvRIP, fpEtherIpOptRecvRIP1, and fpEtherIpOptRecvRIP2 are mutually exclusive.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpEtherIpOptSendRIP 1.3.6.1.4.1.1548.2.1.1.10
Allows sending IP RIP 1 compatible packets to this LAN port when IP routing is enabled: a change requires rebooting. This setting is enabled by default. fpEtherIpOptSendRIP, fpEtherIpOptSendRIP1, and fpEtherIpOptSendRIP2 are mutually exclusive.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpEtherIpOptRecvRIPDefault 1.3.6.1.4.1.1548.2.1.1.11
Allows updating the IP routing table with the default route (i.e. 0.0.0.0) received from this LAN port when IP routing is enabled: this setting is enabled by default. A change on this object requires rebooting.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpEtherIpOptSendRIPDefault 1.3.6.1.4.1.1548.2.1.1.12
Allows this system to advertise itself as the default router on this LAN port when IP routing is enabled. This setting is enabled by default. A change requires rebooting.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpIpxStrNetAddress 1.3.6.1.4.1.1548.2.1.1.13
This objects allows to get or set the IPX external network number for this LAN port: a change requires rebooting. This object is expressed as an ASCII string, converted to hexadecimal by the firmware: use this object instead of fpIpxNetAddress when OCTET STRING is not implemented.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

fpIpDefaultGateway 1.3.6.1.4.1.1548.2.1.1.14
This object allows to get or set the IP address for the default Gateway (default route), and assign it to the interface specified by fpPortNum. This is particularly useful when the device operates as an end-system (host) as opposed to performing IP routing. There can be only one default route in the whole system. When set to 0.0.0.0, no default is defined statically, and it may be discovered dynamically if RIP is allowed on the LAN interface.
OBJECT-TYPE    
  IpAddress  

fpEtherIpOptRecvRIP1 1.3.6.1.4.1.1548.2.1.1.15
Allows the processing of IP RIP 1 packets received from for this LAN port: a change requires rebooting. fpEtherIpOptRecvRIP, fpEtherIpOptRecvRIP1, and fpEtherIpOptRecvRIP2 are mutually exclusive.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpEtherIpOptSendRIP1 1.3.6.1.4.1.1548.2.1.1.16
Allows sending IP RIP 1 packets to this LAN port when IP routing is enabled: a change requires rebooting. fpEtherIpOptSendRIP, fpEtherIpOptSendRIP1, and fpEtherIpOptSendRIP2 are mutually exclusive.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpEtherIpOptRecvRIP2 1.3.6.1.4.1.1548.2.1.1.17
Allows the processing of IP RIP 2 packets received from for this LAN port: a change requires rebooting. fpEtherIpOptRecvRIP, fpEtherIpOptRecvRIP1, and fpEtherIpOptRecvRIP2 are mutually exclusive.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpEtherIpOptSendRIP2 1.3.6.1.4.1.1548.2.1.1.18
Allows sending IP RIP 2 packets to this LAN port when IP routing is enabled: a change requires rebooting. fpEtherIpOptSendRIP, fpEtherIpOptSendRIP1, and fpEtherIpOptSendRIP2 are mutually exclusive.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpIpRIPMulticastAddress 1.3.6.1.4.1.1548.2.1.1.19
This object allows to get or set the RIP 2 Multicast address for this LAN interface: set to 0.0.0.0 to restore the default multicast address (i.e. 224.0.0.9). A change requires rebooting.
OBJECT-TYPE    
  IpAddress  

fpNATState 1.3.6.1.4.1.1548.2.1.1.20
Determines whether IP address/port translation is performed via this LAN interface if the IP protocol is routed (enable) through this LAN interface. A change requires rebooting.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpMtu 1.3.6.1.4.1.1548.2.1.1.21
When non-zero, the desired MTU size for this interface. When zero, use the default MTU size for the interface. The MTU size used is the minimum of the desired MTU size for this interface and the maximum MTU size allowed for the interface.
OBJECT-TYPE    
  INTEGER  

fpEtherOperation 1.3.6.1.4.1.1548.2.2
This object is used to save/load/erase the LAN port (ethernet) configuration to/from FLASH.
OBJECT-TYPE    
  INTEGER save(1), load(2), erase(3)  

etherNatHostMappingTable 1.3.6.1.4.1.1548.2.3
The NAT Host Mapping Table. Used to select a NAT Host Mapping when doing IP address translation.
OBJECT-TYPE    
  SEQUENCE OF  
    EtherNatHostMappingEntry

etherNatHostMappingEntry 1.3.6.1.4.1.1548.2.3.1
OBJECT-TYPE    
  EtherNatHostMappingEntry  

etherFirstPrivateIPAddress 1.3.6.1.4.1.1548.2.3.1.1
The first private IP address which starts the range of private IP addresses which are mapped to public IP addresses.
OBJECT-TYPE    
  IpAddress  

etherLastPrivateIPAddress 1.3.6.1.4.1.1548.2.3.1.2
The last private IP address which ends the range of private IP addresses which are mapped to public IP addresses.
OBJECT-TYPE    
  IpAddress  

etherFirstPublicIPAddress 1.3.6.1.4.1.1548.2.3.1.3
The first public IP address which starts the range of public IP Addresses which are mapped to private IP addresses. The last public IP address in the range is calculated by counting the number of private IP addresses in the private IP address range and creating an equivalent number of IP addresses in the public IP address range so there is a one to one mapping of public IP addresses to private IP addresses.
OBJECT-TYPE    
  IpAddress  

etherNatHostMappingStatus 1.3.6.1.4.1.1548.2.3.1.4
The status column used for creating, modifying, and deleting instances of the columnar objects in this table.
OBJECT-TYPE    
  RowStatus  

etherIPTranslationServerTable 1.3.6.1.4.1.1548.2.4
The IP Translation Server Table. Used to select a server when doing IP address translation.
OBJECT-TYPE    
  SEQUENCE OF  
    EtherIPTranslationServerEntry

etherIPTranslationServerEntry 1.3.6.1.4.1.1548.2.4.1
OBJECT-TYPE    
  EtherIPTranslationServerEntry  

etherIPTranslationServerIPAddress 1.3.6.1.4.1.1548.2.4.1.1
The IP address of the Server when doing IP Address translation.
OBJECT-TYPE    
  IpAddress  

etherIPTranslationProtocol 1.3.6.1.4.1.1548.2.4.1.2
The protocol used by this Server.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

etherIPFirstTranslationPort 1.3.6.1.4.1.1548.2.4.1.3
First public port in range used by this server. This port is what is referenced by the client. A port of 0 is a wild-card signifying any port.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

etherIPLastTranslationPort 1.3.6.1.4.1.1548.2.4.1.4
Last public port in range used by this server. This port is the last port in range and is referenced by the client.. This value must be greater than or equal first public port in range.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

etherIPFirstPrivatePort 1.3.6.1.4.1.1548.2.4.1.5
This is the first private port in range as seen by the server. The public port range is mapped to this private port range. If the public port range is to be the same as the private port range, this port should be the same as the first public port.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

etherIPTranslationStatus 1.3.6.1.4.1.1548.2.4.1.6
The status column used for creating, modifying, and deleting instances of the columnar objects in this table.
OBJECT-TYPE    
  RowStatus  

fpisdn 1.3.6.1.4.1.1548.3
OBJECT IDENTIFIER    

fpIsdnCh1Spid 1.3.6.1.4.1.1548.3.1
The spid number string for 1st B channel.
OBJECT-TYPE    
  DisplayString SIZE(0..30)  

fpIsdnCh2Spid 1.3.6.1.4.1.1548.3.2
The spid number string for 2nd B channel.
OBJECT-TYPE    
  DisplayString SIZE(0..30)  

fpIsdnCh1DirectoryNum 1.3.6.1.4.1.1548.3.3
The directory number string for 1st B channel.
OBJECT-TYPE    
  DisplayString SIZE(0..30)  

fpIsdnCh2DirectoryNum 1.3.6.1.4.1.1548.3.4
The directory number string for 2nd B channel.
OBJECT-TYPE    
  DisplayString SIZE(0..30)  

fpIsdnSwitchType 1.3.6.1.4.1.1548.3.5
Specifies the ISDN switch type.
OBJECT-TYPE    
  INTEGER att5ess(2), dms100(5), kdd(7), net3(8), net3swiss(9), ni1(10), ntt(12), auto(14)  

fpIsdnOperation 1.3.6.1.4.1.1548.3.6
To save or load or erase the ISDN configuration to/from FLASH memory.
OBJECT-TYPE    
  INTEGER save(1), load(2), erase(3)  

fpIsdnCh1Status 1.3.6.1.4.1.1548.3.7
This object shows the current status of B channel 1.
OBJECT-TYPE    
  INTEGER idle(1), opening(2), connected(3), closing(4), alerting(5), dialing(6), out-of-service(7), in-use-by-pots(8)  

fpIsdnCh2Status 1.3.6.1.4.1.1548.3.8
This object shows the current status of B channel 2.
OBJECT-TYPE    
  INTEGER idle(1), opening(2), connected(3), closing(4), alerting(5), dialing(6), out-of-service(7), in-use-by-pots(8)  

fpIsdnCh1ClearCode 1.3.6.1.4.1.1548.3.9
The clearing code of the last call, (0 if a call is in progress) for B channel 1.
OBJECT-TYPE    
  INTEGER  

fpIsdnCh2ClearCode 1.3.6.1.4.1.1548.3.10
The clearing code of the last call, (0 if a call is in progress) for B channel 2.
OBJECT-TYPE    
  INTEGER  

fpIsdnCh1ClearReason 1.3.6.1.4.1.1548.3.11
An explanation (in ASCII) of why the last called was cleared for B channel 1 (the null string if a call is in progress).
OBJECT-TYPE    
  DisplayString  

fpIsdnCh2ClearReason 1.3.6.1.4.1.1548.3.12
An explanation (in ASCII) of why the last called was cleared for B channel 2 (the null string if a call is in progress).
OBJECT-TYPE    
  DisplayString  

fpIsdnSpeed 1.3.6.1.4.1.1548.3.13
Whether the ISDN calls are made at a speed determined by the speed defined in the remote database and processed as indicated by the network (auto) or locked at 56Kb/s, regardless of the remote database settings and the parameters indicated by the network in incoming calls.
OBJECT-TYPE    
  INTEGER auto(1), speed-56k(2)  

fpIsdnDataCallsIn 1.3.6.1.4.1.1548.3.14
This object determines whether ISDN data calls can be received.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpIsdnDataCallsOut 1.3.6.1.4.1.1548.3.15
This object determines whether ISDN data calls can be generated by the device. This can be useful to let the device place voice calls only while ensuring that no data call is ever placed because the filtering/spoofing did not eliminate spurious traffic.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpIsdnLineStatus 1.3.6.1.4.1.1548.3.16
This object shows the current status of the line.
OBJECT-TYPE    
  INTEGER activated(1), deactivated(2)  

fpIsdnStatus 1.3.6.1.4.1.1548.3.17
This object sets/returns the service state for the ISDN line.
OBJECT-TYPE    
  INTEGER inService(1), notOperational(2), startAutoSpid(3), stopAutoSpid(4), autoSpidActive(5), validatingSpids(6), qualifyingSpids(7)  

fpIsdnAutoSpidCounter 1.3.6.1.4.1.1548.3.18
The spid index currently being tried when doing auto spid detection.
OBJECT-TYPE    
  INTEGER  

fpIsdnSwitchTable 1.3.6.1.4.1.1548.3.19
The switch table contains the switches supported by this kernel.
OBJECT-TYPE    
  SEQUENCE OF  
    FpIsdnSwitchEntry

fpIsdnSwitchEntry 1.3.6.1.4.1.1548.3.19.1
Each entry represents one switch type supported by this kernel.
OBJECT-TYPE    
  FpIsdnSwitchEntry  

fpIsdnSwitchTypeIndex 1.3.6.1.4.1.1548.3.19.1.1
Current switch type index.
OBJECT-TYPE    
  INTEGER 1..32  

fpsys 1.3.6.1.4.1.1548.4
OBJECT IDENTIFIER    

fpSysName 1.3.6.1.4.1.1548.4.1
An administratively-assigned name for this managed node. It will be the same name as the one defined in MIB2.
OBJECT-TYPE    
  DisplayString SIZE(0..50)  

fpSysMessage 1.3.6.1.4.1.1548.4.2
An administratively-assigned message for this managed node.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

fpSysPassword 1.3.6.1.4.1.1548.4.3
An administratively-assigned password for this managed node. The password will be used in the authentication phase of PPP. GENERR is returned if not authorized to read the fpSysPassword.
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

fpSysAuthen 1.3.6.1.4.1.1548.4.4
An administratively-assigned authentication override type for this managed node. This is normally set to NONE, which means the normal rules apply. When set to PAP, all the remote entries that have a setting of PAP don't attempt to negotiate CHAP first, but propose only PAP. When set to CHAP, only CHAP authentication is accepted by this node (this makes it easier than changing all the remote entries to have their minimal level of authentication set to CHAP).
OBJECT-TYPE    
  AuthenProtoType  

fpSysOperation 1.3.6.1.4.1.1548.4.5
Use this object to save/load the system configuration (only what is defined in this group) to/from FLASH memory, or perform other control operation such as reboot.
OBJECT-TYPE    
  INTEGER save(1), load(2), erase(3), reboot(4), set-clock(5), reboot-like-factory(6), reboot-like-new(7)  

fpSysSoftwareVer 1.3.6.1.4.1.1548.4.6
Displays the software version run by the system.
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

fpSysHardwareVer 1.3.6.1.4.1.1548.4.7
Displays the system model number, revision and serial number.
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

fpLoginPassword 1.3.6.1.4.1.1548.4.8
Assign or change the administrator's password for login. Writing objects can only be performed when logged-in, using this password. To supply the password for login purposes, use the fpLoginTable object in the fplogin group. GENERR is returned if not authorized to read the fpLoginPassword.
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

fpWriteTimeout 1.3.6.1.4.1.1548.4.9
To set and retrieve a timeout value (in minutes) during which a user logged in can modify objects. When setting this value, the countdown restarts. The timer is first started when the login password is supplied (see the LoginTable object). When the timer expires, a new login must be performed or all writes to writable objects return READONLY. Default -- 10 minutes (until changed). No security timeout -- set to 0.
OBJECT-TYPE    
  INTEGER 1..999  

fpWriteTimer 1.3.6.1.4.1.1548.4.10
This object retrieves the current security timer value. It returns how many minutes are left (if any) before a new login must be performed.
OBJECT-TYPE    
  INTEGER 0..999  

fpCommunityName 1.3.6.1.4.1.1548.4.11
To change or retrieve the SNMP community name. The default name is 'public'.
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

fpInternetFireWall 1.3.6.1.4.1.1548.4.12
To enable or disable the internet firewall filter. The filter discards any IP packet arriving from the WAN with a source IP address belonging to the LAN.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpSysLogout 1.3.6.1.4.1.1548.4.13
Writing to this object prevents any change from any SNMP manager (until logged in again). Changes from telnet and the console are controlled via the login and logout commands, and are independent. After a reboot, SNMP managers are logged out and should log in before changing any configuration.
OBJECT-TYPE    
  INTEGER  

fpIpxSupported 1.3.6.1.4.1.1548.4.14
Indicates whether or not IPX is supported in the router software. For compatibility with previous non-IPX-capable builds, the manager should consider that an error of NOSUCHNAME on this object means that IPX is NOT supported.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpSysCallerIdTable 1.3.6.1.4.1.1548.4.15
This table defines the types of connections for which CallerID information should be verified.
OBJECT-TYPE    
  SEQUENCE OF  
    FpSysCallerIdEntry

fpSysCallerIdEntry 1.3.6.1.4.1.1548.4.15.1
An entry in the fpSysCallerIdTable specifies that calls of the type used as an index, should be validated by Caller ID verification (using dodCallerTable).
OBJECT-TYPE    
  FpSysCallerIdEntry  

fpCallerIdEnabled 1.3.6.1.4.1.1548.4.15.1.1
Set this object to enable or disable CallerId verification for the specified type of connection.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpMIBCompatibility 1.3.6.1.4.1.1548.4.16
Indicates that this private MIB is fully compatible with RFC 1155. For compatibility with previous builds, the manager should consider that an error of NOSUCHNAME on this object means that the 'old' value applies, (meaning the enumeration of INTEGERs are mostly zero-based instead of one-based).
OBJECT-TYPE    
  INTEGER old(1), new(2)  

fpPOTSInstalled 1.3.6.1.4.1.1548.4.17
Indicates whether or not POTS hardware is installed AND is software supported. For compatibility with previous builds, the manager should consider that an error of NOSUCHNAME on this object means that POTS hardware and software are not available.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpSysLastLogEvent 1.3.6.1.4.1.1548.4.18
The last system event reported to the console. This includes the timestamp, the subsystem and the actual text message of the event.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

fpSysSingleUser 1.3.6.1.4.1.1548.4.19
This IP address used to define the single address to which IP translation was to occur (one client system at a time), or cancelling the translation when NULL. Network Address Translation (NAT) and its ability to define server mappings (with sysIPTranslationServerTable) has rendered this object obsolete: this object is now always returned as the IP address 0.0.0.0 and cannot be set to anything else.
OBJECT-TYPE    
  NetworkAddress  

fpSysYear 1.3.6.1.4.1.1548.4.20
Set this object to specify the year for the real time clock, protected by a battery when the power is off. When all the related parameters (fpSysYear, fpSysMonth, fpSysDay, fpSysHour, fpSysMinute, fpSysSecond) are set, set the fpSysOperation to set-clock(5).
OBJECT-TYPE    
  INTEGER  

fpSysMonth 1.3.6.1.4.1.1548.4.21
Set this object to specify the month for the real time clock, protected by a battery when the power is off. When all the related parameters (fpSysYear, fpSysMonth, fpSysDay, fpSysHour, fpSysMinute, fpSysSecond) are set, set the fpSysOperation to set-clock(5).
OBJECT-TYPE    
  INTEGER 1..12  

fpSysDay 1.3.6.1.4.1.1548.4.22
Set this object to specify the day for the real time clock, protected by a battery when the power is off. When all the related parameters (fpSysYear, fpSysMonth, fpSysDay, fpSysHour, fpSysMinute, fpSysSecond) are set, set the fpSysOperation to set-clock(5).
OBJECT-TYPE    
  INTEGER 1..31  

fpSysHour 1.3.6.1.4.1.1548.4.23
Set this object to specify the hour for the real time clock, protected by a battery when the power is off. When all the related parameters (fpSysYear, fpSysMonth, fpSysDay, fpSysHour, fpSysMinute, fpSysSecond) are set, set the fpSysOperation to set-clock(5).
OBJECT-TYPE    
  INTEGER 0..23  

fpSysMinute 1.3.6.1.4.1.1548.4.24
Set this object to specify the minutes for the real time clock, protected by a battery when the power is off. When all the related parameters (fpSysYear, fpSysMonth, fpSysDay, fpSysHour, fpSysMinute, fpSysSecond) are set, set the fpSysOperation to set-clock(5).
OBJECT-TYPE    
  INTEGER 0..59  

fpSysSecond 1.3.6.1.4.1.1548.4.25
Set this object to specify the seconds for the real time clock, protected by a battery when the power is off. When all the related parameters (fpSysYear, fpSysMonth, fpSysDay, fpSysHour, fpSysMinute, fpSysSecond) are set, set the fpSysOperation to set-clock(5).
OBJECT-TYPE    
  INTEGER 0..59  

fpSysDefaultSingleUser 1.3.6.1.4.1.1548.4.26
Network Address Translation (NAT) and its ability to define server mappings (with sysIPTranslationServerTable) has rendered this object obsolete. For backwards compatibility purposes, this object still allows to set the IP address of the client for which IP address translation is to be performed by default. However, to take effect, the configuration must be saved (with fpEtherOperation=save(1)) and the system must be restarted.
OBJECT-TYPE    
  NetworkAddress  

fpSysBootpRelay 1.3.6.1.4.1.1548.4.27
This object allows to get or set the IP address of the DHCP/BOOTP Server when this router is acting as a Bootp relay agent. When set to 0.0.0.0, this router will not act as a Bootp relay agent. This setting is saved to non-volatile memory, with both fpSysOperation=save(1) and fpEtherOperation=save(1).
OBJECT-TYPE    
  NetworkAddress  

fpSysKernelRevision 1.3.6.1.4.1.1548.4.28
This object represents the number of times that the source code got changed, possibly resulting in the support of new features. This number is intended to be used by an SNMP manager to determine what features set is supported by the kernel software (compared to what is expected as a minimum). This objects differs from fpSysSoftwareVer which is a string containing an administratively defined version.
OBJECT-TYPE    
  INTEGER  

fpSysTelnetPort 1.3.6.1.4.1.1548.4.29
The TCP port for reception of telnet connections to the router. Setting this value to zero disables telnetting to the router. This change requires a reboot to take affect.
OBJECT-TYPE    
  INTEGER 0..65535  

fpSysSNMPPort 1.3.6.1.4.1.1548.4.30
The TCP port for reception of SNMP requests to the router. Setting this value to zero disables SNMP management of the router. This change requires a reboot to take affect.
OBJECT-TYPE    
  INTEGER 0..65535  

fpWAN2WANForwarding 1.3.6.1.4.1.1548.4.31
To enable or disable the forwarding of data traffic from one wan link to another wan link.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpUdpRelayTable 1.3.6.1.4.1.1548.4.32
This table defines UDP ports for which relaying should should be performed when this UDP traffic is broadcast.
OBJECT-TYPE    
  SEQUENCE OF  
    FpUdpRelayEntry

fpUdpRelayEntry 1.3.6.1.4.1.1548.4.32.1
An entry in the fpUdpRelayTable specifies that UDP packets which are broadcast to the specified ports should be relayed to the specified IP address.
OBJECT-TYPE    
  FpUdpRelayEntry  

fpUdpRelayFirstPort 1.3.6.1.4.1.1548.4.32.1.1
First UDP port of range of UDP ports which will be relayed.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

fpUdpRelayLastPort 1.3.6.1.4.1.1548.4.32.1.2
Last UDP port of range of UDP ports which will be relayed.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

fpUdpRelayIPAddress 1.3.6.1.4.1.1548.4.32.1.3
IP address to receive UDP broadcast traffic.
OBJECT-TYPE    
  IpAddress  

fpUdpRelayStatus 1.3.6.1.4.1.1548.4.32.1.4
The status column used for creating, modifying, and deleting instances of the columnar objects in this table.
OBJECT-TYPE    
  RowStatus  

fpOneWANConnection 1.3.6.1.4.1.1548.4.33
To enable or disable the bringing up of more than one wan link at a time to different destinations.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpSysHTTPPort 1.3.6.1.4.1.1548.4.34
The TCP port for reception of HTTP requests to the router. Setting this value to zero disables HTTP management of the router. This change requires a reboot to take affect.
OBJECT-TYPE    
  INTEGER 0..65535  

fpDirectedBroadcasts 1.3.6.1.4.1.1548.4.35
Enable/disable directed broadcasts to a directly connected interface.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpBlockNetBIOSDefault 1.3.6.1.4.1.1548.4.36
To set the default when a new remote is created that controls if the remote will block NetBIOS traffic.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fpSysFlashAvailable 1.3.6.1.4.1.1548.4.37
This object represents the number of bytes of flash available in the flash file system.
OBJECT-TYPE    
  INTEGER  

fpVoiceTable 1.3.6.1.4.1.1548.4.38
This table defines voice ports for voice routers.
OBJECT-TYPE    
  SEQUENCE OF  
    FpVoiceEntry

fpVoiceEntry 1.3.6.1.4.1.1548.4.38.1
An entry in the fpVoiceTable specifies voice information for an voice router; such as the ATM PVC or the Frame Relay DLCI.
OBJECT-TYPE    
  FpVoiceEntry  

fpVoiceIndex 1.3.6.1.4.1.1548.4.38.1.1
The voice port index number.
OBJECT-TYPE    
  INTEGER 1..16  

fpVoicePort 1.3.6.1.4.1.1548.4.38.1.2
This object represents the ATM PVC or the Frame Relay DLCI number for the voice port.
OBJECT-TYPE    
  DisplayString  

fpEchoTable 1.3.6.1.4.1.1548.4.39
This table defines echo ports.
OBJECT-TYPE    
  SEQUENCE OF  
    FpEchoEntry

fpEchoEntry 1.3.6.1.4.1.1548.4.39.1
An entry in the fpEchoTable specifies echo information for a voice router; such as the ATM PVC or the Frame Relay DLCI.
OBJECT-TYPE    
  FpEchoEntry  

fpEchoIndex 1.3.6.1.4.1.1548.4.39.1.1
The echo port index number.
OBJECT-TYPE    
  INTEGER 1..16  

fpEchoPort 1.3.6.1.4.1.1548.4.39.1.2
This object represents the ATM PVC or the Frame Relay DLCI number for the echo port.
OBJECT-TYPE    
  DisplayString  

fpOptionTable 1.3.6.1.4.1.1548.4.40
This table defines Kernel Options.
OBJECT-TYPE    
  SEQUENCE OF  
    FpOptionEntry

fpOptionEntry 1.3.6.1.4.1.1548.4.40.1
A string in the fpOptionTable specifies information pertaining to options built into the kernel -and- which options are available.
OBJECT-TYPE    
  FpOptionEntry  

fpOptionIndex 1.3.6.1.4.1.1548.4.40.1.1
An index number representing a line of options.
OBJECT-TYPE    
  INTEGER  

fpOptionString 1.3.6.1.4.1.1548.4.40.1.2
This object represents a an string for the option built into the kernel.
OBJECT-TYPE    
  DisplayString  

fpOptionAvailable 1.3.6.1.4.1.1548.4.40.1.3
Returns enable(1) if the option is available for use.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

fplogin 1.3.6.1.4.1.1548.5
OBJECT IDENTIFIER    

fpLoginTable 1.3.6.1.4.1.1548.5.1
This object returns the login status to the Manager.
OBJECT-TYPE    
  SEQUENCE OF  
    FpLoginEntry

fpLoginEntry 1.3.6.1.4.1.1548.5.1.1
OBJECT-TYPE    
  FpLoginEntry  

fpLoginAction 1.3.6.1.4.1.1548.5.1.1.1
This object will return the login status to the Manager. Use this object to login to system by giving the administrator's password as index. The login status are: 1 -- login OK. Password matches with system's password. 2 -- login fail. Password mismatch.
OBJECT-TYPE    
  INTEGER success(1), failure(2)  

fpWan 1.3.6.1.4.1.1548.6
OBJECT IDENTIFIER    

fpWanTable 1.3.6.1.4.1.1548.6.1
A list of WAN interface entries.
OBJECT-TYPE    
  SEQUENCE OF  
    FpWanEntry

fpWanEntry 1.3.6.1.4.1.1548.6.1.1
An interface entry containing objects at the WAN layer...
OBJECT-TYPE    
  FpWanEntry  

fpWanIndex 1.3.6.1.4.1.1548.6.1.1.1
The interface index number.
OBJECT-TYPE    
  INTEGER 1..16  

fpWanInstantOutUtil 1.3.6.1.4.1.1548.6.1.1.2
Intantaneous output bandwidth utilization, from 0 to 100 (in 1% increments).
OBJECT-TYPE    
  INTEGER 0..100  

fpWanInstantInUtil 1.3.6.1.4.1.1548.6.1.1.3
Intantaneous input bandwidth utilization, from 0 to 100 (in 1% increments).
OBJECT-TYPE    
  INTEGER 0..100  

fpWanAvgOutUtil 1.3.6.1.4.1.1548.6.1.1.4
Sliding average of output bandwidth utilization, from 0 to 100 (in 1% increments).
OBJECT-TYPE    
  INTEGER 0..100  

fpWanAvgInUtil 1.3.6.1.4.1.1548.6.1.1.5
Sliding average of input bandwidth utilization, from 0 to 100 (in 1% increments).
OBJECT-TYPE    
  INTEGER 0..100  

fpWanRemoteName 1.3.6.1.4.1.1548.6.1.1.6
Name of user/destination that this port is currently connected to, if known.
OBJECT-TYPE    
  DisplayString SIZE(0..20)  

fpWanRemoteTime 1.3.6.1.4.1.1548.6.1.1.7
The number of seconds that we have been connected to this particular remote across this WAN link.
OBJECT-TYPE    
  INTEGER  

fpWanIfIndex 1.3.6.1.4.1.1548.6.1.1.8
The corresponding MIB-II ifIndex for this interface
OBJECT-TYPE    
  INTEGER  

fpWanOutSpeed 1.3.6.1.4.1.1548.6.1.1.9
An estimate of the interface's current bandwidth in bits per second, for the transmit side (relative to this device).
OBJECT-TYPE    
  Gauge  

fpWanInSpeed 1.3.6.1.4.1.1548.6.1.1.10
An estimate of the interface's current bandwidth in bits per second, for the receive side (relative to this device).
OBJECT-TYPE    
  Gauge  

fppots 1.3.6.1.4.1.1548.7
OBJECT IDENTIFIER    

potsOperation 1.3.6.1.4.1.1548.7.1
Use this object to give commands to save, load or erase POTS configuration in FLASH memory.
OBJECT-TYPE    
  INTEGER save(1), load(2), erase(3)  

potsTable 1.3.6.1.4.1.1548.7.2
The table used to configure and manage the POTS interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    PotsEntry

potsEntry 1.3.6.1.4.1.1548.7.2.1
OBJECT-TYPE    
  PotsEntry  

potsIndex 1.3.6.1.4.1.1548.7.2.1.1
Index used to access a potsEntry: maps to the connectors marked POTS1 and POTS2.
OBJECT-TYPE    
  INTEGER 1..2  

potsEnabled 1.3.6.1.4.1.1548.7.2.1.2
Enable or disable the POTS functionality at the specified connector.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

potsOpMode 1.3.6.1.4.1.1548.7.2.1.3
Specifies the type of calls that should be handled by this POTS interface. The default is to allow both incoming and outgoing calls.
OBJECT-TYPE    
  INTEGER both(1), answer(2), dial(3)  

potsPreemptMode 1.3.6.1.4.1.1548.7.2.1.4
Specifies the behavior of analog calls versus data calls. The default is both: voice calls always preempt data calls.
OBJECT-TYPE    
  INTEGER both(1), in(2), out(3), none(4)  

potsAutoMode 1.3.6.1.4.1.1548.7.2.1.5
Defines whether the preemption mode defined by potsPreemptMode is to be performed automatically or whether the user should be prompted first. This only applies when the preemption of that type is allowed.
OBJECT-TYPE    
  INTEGER both(1), in(2), out(3), none(4)  

potsPhoneCnt 1.3.6.1.4.1.1548.7.2.1.6
Indicates the number of phone numbers associated with this POTS interface.
OBJECT-TYPE    
  INTEGER 0..8  

potsLocalNumber 1.3.6.1.4.1.1548.7.2.1.7
The local phone number used by this POTS interface during the last analog call processed (incoming and outgoing).
OBJECT-TYPE    
  DisplayString SIZE(0..30)  

potsRemoteNumber 1.3.6.1.4.1.1548.7.2.1.8
The remote phone number used by this POTS interface during the last analog call processed (outgoing and incoming when caller ID is available).
OBJECT-TYPE    
  DisplayString SIZE(0..30)  

potsState 1.3.6.1.4.1.1548.7.2.1.9
Current state of this POTS interface.
OBJECT-TYPE    
  INTEGER other(1), not-available(2), idle(3), wait-dialtone(4), ringing(5), dialing(6), proceeding(7), connected-incoming(8), connected-outgoing(9), disconnected(10), entering-ip-addr(11), held-call(12)  

potsIsdnChannel 1.3.6.1.4.1.1548.7.2.1.10
Indicates which ISDN channel (1 or 2) is associated with this POTS interface for the duration of this call. Additional information (like the clearing cause and reason are available via the ISDN group variables. When no ISDN channel is assigned to this POTS interface yet, 0 is returned
OBJECT-TYPE    
  INTEGER 0..2  

potsWanIndex 1.3.6.1.4.1.1548.7.2.1.11
Indicates which Wan interface (1 or 2) is associated with this POTS interface for the duration of this call. Additional information (like the duration of the call is available via the WAN interface group variables. When no WAN interface is mapped to this POTS interface yet, 0 is returned
OBJECT-TYPE    
  INTEGER 0..2  

potsPhoneTable 1.3.6.1.4.1.1548.7.3
The table used to associate phone numbers and POTS interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    PotsPhoneEntry

potsPhoneEntry 1.3.6.1.4.1.1548.7.3.1
OBJECT-TYPE    
  PotsPhoneEntry  

potsPhoneNumber 1.3.6.1.4.1.1548.7.3.1.1
A phone number associated with the specified POTS interface, such that when an incoming analog call arrives, that interface rings, if allowed. This is used as an index into the POTS phone number table.
OBJECT-TYPE    
  DisplayString SIZE(0..30)  

potsPhoneOperation 1.3.6.1.4.1.1548.7.3.1.2
Perform a set on this object to add or remove the association between the specified phone number and the specified POTS interface.
OBJECT-TYPE    
  INTEGER add(1), remove(2)  

fpdownload 1.3.6.1.4.1.1548.8
OBJECT IDENTIFIER    

fpDLForceOnBoot 1.3.6.1.4.1.1548.8.1
When set to a 1, the system will request a download, during the next system restart. If no server is found and the current image in flash memory is valid, the system will boot using the flash-resident image.
OBJECT-TYPE    
  INTEGER  

fpDLCommitRAMToFlash 1.3.6.1.4.1.1548.8.2
This object only exists for compatibility reasons.
OBJECT-TYPE    
  INTEGER  

fpDLInitiateColdBoot 1.3.6.1.4.1.1548.8.3
When written with a 1, the boot software intiates a system reboot. All MIB variables used to control the exact nature of the download should be set, prior to activating a system reset. A read always returns a 0.
OBJECT-TYPE    
  INTEGER  

fpDLTFTPRequestHost 1.3.6.1.4.1.1548.8.4
The IP address of the server to be used, when firmware is to be loaded across the network (network boot).
OBJECT-TYPE    
  NetworkAddress  

fpDLTFTPRequest 1.3.6.1.4.1.1548.8.5
The filename requested of the server, when firmware is to be loaded across the network (network boot).
OBJECT-TYPE    
  DisplayString  

fpDLLastImageFilename 1.3.6.1.4.1.1548.8.6
Filename of the last image to be successfully loaded into memory.
OBJECT-TYPE    
  DisplayString  

fpDLLastServerIPAddress 1.3.6.1.4.1.1548.8.7
The IP address of the server used to load the present image in flash memory.
OBJECT-TYPE    
  NetworkAddress  

fpDLFlashSize 1.3.6.1.4.1.1548.8.8
Denotes the size, in bytes, of flash memory con- tained on this module.
OBJECT-TYPE    
  INTEGER  

fpDLFlashCount 1.3.6.1.4.1.1548.8.9
Denotes the number of times that flash memory has been reprogrammed. This value is initialized to 1, when the module is initially powered up.
OBJECT-TYPE    
  INTEGER  

fpDLFirmwareBase 1.3.6.1.4.1.1548.8.10
Denotes the starting address of the firmware in RAM.
OBJECT-TYPE    
  INTEGER  

fpDLFirmwareTop 1.3.6.1.4.1.1548.8.11
Denotes the ending address of firmware in RAM.
OBJECT-TYPE    
  INTEGER  

fpDLFirmwareStart 1.3.6.1.4.1.1548.8.12
Denotes the start address of the firmware, in RAM, as established by the boot process.
OBJECT-TYPE    
  INTEGER  

fpDLBootRev 1.3.6.1.4.1.1548.8.13
Denotes the revision of boot firmware in the module. The first octets provides the version, and the second provides the revision.
OBJECT-TYPE    
  OCTET STRING SIZE(9)  

fpDLForceBootp 1.3.6.1.4.1.1548.8.14
When set, this variable forces the client to send a BOOTP request packet when rebooting. The client will make several attempts before timing out if a server does not respond. This variable stays set. When set to a 1 it should always be read as a one. When set to zero it should always be read as zero.
OBJECT-TYPE    
  INTEGER  

fpDLServerName 1.3.6.1.4.1.1548.8.15
This OID is reserved for future use of the Bootp server name. This field can be used when a client wants to get boot information from a particular bootp server.
OBJECT-TYPE    
  OCTET STRING  

fpDLOnLineDownLoad 1.3.6.1.4.1.1548.8.16
During normal operation this object has the value of 1. By setting this object to a value of forceDownLoad(2) an online download will be performed. By setting this object to a value of forceDownLoadReset(3) an online download will be performed and a reset will be forced upon successful completion of the download. The forceUpLoad(4) operation causes the local file specified in fpDLLocalFileName to be uploaded to the TFTP server fpDLNetAddress with the file name fpDLFileName. The forceRemove(5) operation deletes the local file specified in fpDLLocalFileName.
OBJECT-TYPE    
  INTEGER normalOperation(1), forceDownLoad(2), forceDownLoadReset(3), forceUpLoad(4), forceRemove(5)  

fpDLOperStatus 1.3.6.1.4.1.1548.8.17
This object reflects the status of download/upload operations. A value of normalOperation(3) reflects either a download was started but has finished normally and no reset was specified or no download has been started. A value of downLoadActive only appears while a download is in progress. A value of downLoadCompleteError reflects that a download was started however an error was detected. Similarly when an upload is in progress upLoadActive(6) is returned and if an error occurs upLoadCompeteError(7) is returned. A value of removeActive(8) indicates that a local file is being removed and removeCompleteError(9) indicates a failure to remove the file.
OBJECT-TYPE    
  INTEGER other(1), unknown(2), normalOperation(3), downLoadActive(4), downLoadCompleteError(5), upLoadActive(6), upLoadCompleteError(7), removeActive(8), removeCompleteError(9)  

fpDLNetAddress 1.3.6.1.4.1.1548.8.18
IP Address of the server to be used when an image is to be downloaded using the Runtime TFTP Download.
OBJECT-TYPE    
  NetworkAddress  

fpDLFileName 1.3.6.1.4.1.1548.8.19
Filename requested of the server when an image is to be downloaded using the Runtime TFTP Download. This should be a complete path filename.
OBJECT-TYPE    
  DisplayString SIZE(1..127)  

fpDLErrorString 1.3.6.1.4.1.1548.8.20
If the value of fpDLOperStatus is downloadCompleteError(5) or uploadCompleteError(7) then this object will provide a more complete description of the error. Otherwise this object will be the zero length string.
OBJECT-TYPE    
  DisplayString  

fpDLTftpServerGatewayIPAddress 1.3.6.1.4.1.1548.8.21
The IP address of the gateway/router which connects this SNMP agent to the TFTP server (0.0.0.0 if none).
OBJECT-TYPE    
  NetworkAddress  

fpDLBlockCount 1.3.6.1.4.1.1548.8.22
Current TFTP block count of an active session. If no TFTP transfer is in progress, zero is returned.
OBJECT-TYPE    
  INTEGER  

fpDLBootPartitionStatus 1.3.6.1.4.1.1548.8.23
Status of the boot partition or paritions. A value of good(1) indicates that all boot partitions contain a valid checksum. A value of bad(2) indicates that one or more boot partitions contain an invalid checksum and the the image was not able to fix the invalid boot partition. A value of inProgress(3) indicates that the image is attempting to fix an invalid boot partition and this status will change to either good(1) or bad(2).
OBJECT-TYPE    
  INTEGER good(1), bad(2), inProgress(3)  

fpDLLocalFileName 1.3.6.1.4.1.1548.8.24
Filename used on the local file system whenever a TFTP download or upload is to be processed.
OBJECT-TYPE    
  DisplayString SIZE(1..12)  

fpDLBootVersion 1.3.6.1.4.1.1548.8.25
Returns a string indicating the boot code version.
OBJECT-TYPE    
  DisplayString SIZE(1..127)  

fpDLBootReason 1.3.6.1.4.1.1548.8.26
Reason for the last reboot.
OBJECT-TYPE    
  INTEGER other(1), power-up(2), reset-switch(3), software-reboot(4), double-bus-fault(5), hardware-watchdog(6), loss-of-clock(7), suicide(8)  

fpiptranslate 1.3.6.1.4.1.1548.9
OBJECT IDENTIFIER    

sysIPTranslationServerTable 1.3.6.1.4.1.1548.9.1
The IP Translation Server Table. Used to select a server when doing IP address translation.
OBJECT-TYPE    
  SEQUENCE OF  
    SysIPTranslationServerEntry

sysIPTranslationServerEntry 1.3.6.1.4.1.1548.9.1.1
OBJECT-TYPE    
  SysIPTranslationServerEntry  

sysIPTranslationServerIPAddress 1.3.6.1.4.1.1548.9.1.1.1
The IP address of the Server when doing IP Address translation.
OBJECT-TYPE    
  IpAddress  

sysIPTranslationProtocol 1.3.6.1.4.1.1548.9.1.1.2
The protocol used by this Server.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

sysIPFirstTranslationPort 1.3.6.1.4.1.1548.9.1.1.3
First public port in range used by this server. This port is what is referenced by the client. A port of 0 is a wild-card signifying any port.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

sysIPLastTranslationPort 1.3.6.1.4.1.1548.9.1.1.4
Last public port in range used by this server. This port is the last port in range and is referenced by the client.. This value must be greater than or equal first public port in range.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

sysIPFirstPrivatePort 1.3.6.1.4.1.1548.9.1.1.5
This is the first private port in range as seen by the server. The public port range is mapped to this private port range. If the public port range is to be the same as the private port range, this port should be the same as the first public port.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

sysIPTranslationStatus 1.3.6.1.4.1.1548.9.1.1.6
The status column used for creating, modifying, and deleting instances of the columnar objects in this table.
OBJECT-TYPE    
  RowStatus  

sysNatHostMappingTable 1.3.6.1.4.1.1548.9.2
The NAT Host Mapping Table. Used to select a NAT Host Mapping when doing IP address translation.
OBJECT-TYPE    
  SEQUENCE OF  
    SysNatHostMappingEntry

sysNatHostMappingEntry 1.3.6.1.4.1.1548.9.2.1
OBJECT-TYPE    
  SysNatHostMappingEntry  

sysFirstPrivateIPAddress 1.3.6.1.4.1.1548.9.2.1.1
The first private IP address which starts the range of private IP addresses which are mapped to public IP addresses.
OBJECT-TYPE    
  IpAddress  

sysLastPrivateIPAddress 1.3.6.1.4.1.1548.9.2.1.2
The last private IP address which ends the range of private IP addresses which are mapped to public IP addresses.
OBJECT-TYPE    
  IpAddress  

sysFirstPublicIPAddress 1.3.6.1.4.1.1548.9.2.1.3
The first public IP address which starts the range of public IP Addresses which are mapped to private IP addresses. The last public IP address in the range is calculated by counting the number of private IP addresses in the private IP address range and creating an equivalent number of IP addresses in the public IP address range so there is a one to one mapping of public IP addresses to private IP addresses.
OBJECT-TYPE    
  IpAddress  

sysNatHostMappingStatus 1.3.6.1.4.1.1548.9.2.1.4
The status column used for creating, modifying, and deleting instances of the columnar objects in this table.
OBJECT-TYPE    
  RowStatus  

fpdhcp 1.3.6.1.4.1.1548.10
OBJECT IDENTIFIER    

dhcpOperation 1.3.6.1.4.1.1548.10.1
Use this object to give commands to save, load or erase DHCP configuration in FLASH memory.
OBJECT-TYPE    
  INTEGER save(1), load(2), erase(3), dhcpenable(4), dhcpdisable(5)  

dhcpGlobalTftpServer 1.3.6.1.4.1.1548.10.2
IP address for the TFTP server. This global value is used as the next server for booting if the Subnet AND Client lease do not have a TFTP server defined. 0.0.0.0 clears this entry.
OBJECT-TYPE    
  IpAddress  

dhcpGlobalTftpFile 1.3.6.1.4.1.1548.10.3
Name of file for booting. This value is used ONLY if the global value for the TFTP server is set.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

dhcpGlobalLeaseTime 1.3.6.1.4.1.1548.10.4
Global Lease Time value in hours. A value of 0 selects the Default Lease Time.
OBJECT-TYPE    
  INTEGER  

dhcpCodeTable 1.3.6.1.4.1.1548.10.5
The table used to define DHCP option codes.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpCodeEntry

dhcpCodeEntry 1.3.6.1.4.1.1548.10.5.1
OBJECT-TYPE    
  DhcpCodeEntry  

dhcpOptionCode 1.3.6.1.4.1.1548.10.5.1.1
DHCP Defined Option Code.
OBJECT-TYPE    
  INTEGER 0..255  

dhcpMinCount 1.3.6.1.4.1.1548.10.5.1.2
Minimum allowed number of values for this option.
OBJECT-TYPE    
  INTEGER 0..255  

dhcpMaxCount 1.3.6.1.4.1.1548.10.5.1.3
Maximum allowed number of values for this option.
OBJECT-TYPE    
  INTEGER 0..255  

dhcpOptionType 1.3.6.1.4.1.1548.10.5.1.4
Values for this Option are of this type.
OBJECT-TYPE    
  DhcpOptionType  

dhcpOptionCodeStatus 1.3.6.1.4.1.1548.10.5.1.5
The status column used for creating, modifying, and deleting instances of the columnar objects in this table.
OBJECT-TYPE    
  RowStatus  

dhcpGlobalValueTable 1.3.6.1.4.1.1548.10.6
The table used to set or clear Global DHCP option values.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpGlobalValueEntry

dhcpGlobalValueEntry 1.3.6.1.4.1.1548.10.6.1
OBJECT-TYPE    
  DhcpGlobalValueEntry  

dhcpGlobalValueCode 1.3.6.1.4.1.1548.10.6.1.1
DHCP Option Code as defined in rfc1533.
OBJECT-TYPE    
  INTEGER 0..255  

dhcpGlobalValueType 1.3.6.1.4.1.1548.10.6.1.2
Type of value for this DHCP Option Code.
OBJECT-TYPE    
  DhcpOptionType  

dhcpGlobalValue 1.3.6.1.4.1.1548.10.6.1.3
Value for this DHCP Option.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

dhcpGlobalValueStatus 1.3.6.1.4.1.1548.10.6.1.4
The status column used for creating, modifying, and deleting instances of the columnar objects in this table.
OBJECT-TYPE    
  RowStatus  

dhcpSubnetTable 1.3.6.1.4.1.1548.10.7
The table used to set or clear DHCP subnet information.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpSubnetEntry

dhcpSubnetEntry 1.3.6.1.4.1.1548.10.7.1
OBJECT-TYPE    
  DhcpSubnetEntry  

dhcpSubnetAddress 1.3.6.1.4.1.1548.10.7.1.1
DHCP Subnet address.
OBJECT-TYPE    
  IpAddress  

dhcpSubnetMask 1.3.6.1.4.1.1548.10.7.1.2
DHCP Subnet Mask. If the Subnet does NOT exist when one attempts to set the Subnet Mask, the Subnet will be automatically created.
OBJECT-TYPE    
  IpAddress  

dhcpSubnetFirstIpAddress 1.3.6.1.4.1.1548.10.7.1.3
First Ip Address in the Subnet Pool. 0.0.0.0 clears both the First Ip Address and Last Ip Address.
OBJECT-TYPE    
  IpAddress  

dhcpSubnetLastIpAddress 1.3.6.1.4.1.1548.10.7.1.4
Last Ip Address in the Subnet Pool. 0.0.0.0 clears both the First Ip Address and Last Ip Address.
OBJECT-TYPE    
  IpAddress  

dhcpSubnetTftpServer 1.3.6.1.4.1.1548.10.7.1.5
IP address for the TFTP server. This Subnet value is used as the next server for booting if the Client lease does not have a TFTP server defined. 0.0.0.0 clears this entry.
OBJECT-TYPE    
  IpAddress  

dhcpSubnetTftpFile 1.3.6.1.4.1.1548.10.7.1.6
Name of file for booting. This value is used ONLY if the Subnet value for the TFTP server is set.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

dhcpSubnetBootp 1.3.6.1.4.1.1548.10.7.1.7
Allow or Disallow servicing of Bootp requests for this Subnet. Default is Disallow. A Client Lease within this Subnet can still allow Bootp requests.
OBJECT-TYPE    
  INTEGER allow(1), disallow(2)  

dhcpSubnetLeaseTime 1.3.6.1.4.1.1548.10.7.1.8
Subnet Default Lease Time value in hours. A value of 0 selects the Default Lease Time.
OBJECT-TYPE    
  INTEGER  

dhcpSubnetStatus 1.3.6.1.4.1.1548.10.7.1.9
The status column used for creating, modifying, and deleting instances of the columnar objects in this table.
OBJECT-TYPE    
  RowStatus  

dhcpSubnetConflictActions 1.3.6.1.4.1.1548.10.7.1.10
What this DHCP server should do with this subnet if this subnet is for the local LAN and another DHCP server for the local LAN exists.
OBJECT-TYPE    
  INTEGER docontinue(1), dostop(2)  

dhcpSubnetValueTable 1.3.6.1.4.1.1548.10.8
The table used to set or clear Subnet DHCP option values.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpSubnetValueEntry

dhcpSubnetValueEntry 1.3.6.1.4.1.1548.10.8.1
OBJECT-TYPE    
  DhcpSubnetValueEntry  

dhcpSubnetValueCode 1.3.6.1.4.1.1548.10.8.1.1
DHCP Option Code as defined in rfc1533.
OBJECT-TYPE    
  INTEGER 0..255  

dhcpSubnetValueType 1.3.6.1.4.1.1548.10.8.1.2
Type of value for this DHCP Option Code.
OBJECT-TYPE    
  DhcpOptionType  

dhcpSubnetValue 1.3.6.1.4.1.1548.10.8.1.3
Value for this DHCP Option.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

dhcpSubnetValueStatus 1.3.6.1.4.1.1548.10.8.1.4
The status column used for creating, modifying, and deleting instances of the columnar objects in this table.
OBJECT-TYPE    
  RowStatus  

dhcpClientTable 1.3.6.1.4.1.1548.10.9
The table used to set or clear DHCP Client Lease information.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpClientEntry

dhcpClientEntry 1.3.6.1.4.1.1548.10.9.1
OBJECT-TYPE    
  DhcpClientEntry  

dhcpClientAddress 1.3.6.1.4.1.1548.10.9.1.1
DHCP Client Lease address. To iterate through the list of client entries for a particular subnet use the subnet ip address as the index and attempt to get the next entry.
OBJECT-TYPE    
  IpAddress  

dhcpClientTftpServer 1.3.6.1.4.1.1548.10.9.1.2
IP address for the TFTP server. This Client value is used as the next server for booting. 0.0.0.0 clears this entry.
OBJECT-TYPE    
  IpAddress  

dhcpClientTftpFile 1.3.6.1.4.1.1548.10.9.1.3
Name of file for booting. This value is used ONLY if the Client value for the TFTP server is set.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

dhcpClientBootp 1.3.6.1.4.1.1548.10.9.1.4
Allow or Disallow servicing of Bootp requests for this Subnet. Default is Disallow. If Enabled this Client Lease will satisfy a Bootp request even if the Subnet has Bootp Disallowed.
OBJECT-TYPE    
  INTEGER allow(1), disallow(2)  

dhcpClientLeaseTime 1.3.6.1.4.1.1548.10.9.1.5
Client Default Lease Time value in hours. A value of 0 selects the Default Lease Time.
OBJECT-TYPE    
  INTEGER  

dhcpClientExpireTimeYear 1.3.6.1.4.1.1548.10.9.1.6
Time Client Lease expire time-year. If 0, entry is expired.
OBJECT-TYPE    
  INTEGER  

dhcpClientExpireTimeMonth 1.3.6.1.4.1.1548.10.9.1.7
Time Client Lease expire time-month.
OBJECT-TYPE    
  INTEGER 1..12  

dhcpClientExpireTimeDay 1.3.6.1.4.1.1548.10.9.1.8
Time Client Lease expire time-day.
OBJECT-TYPE    
  INTEGER 1..31  

dhcpClientExpireTimeHour 1.3.6.1.4.1.1548.10.9.1.9
Time Client Lease expire time-hour.
OBJECT-TYPE    
  INTEGER 0..23  

dhcpClientExpireTimeMinute 1.3.6.1.4.1.1548.10.9.1.10
Time Client Lease expire time-minute.
OBJECT-TYPE    
  INTEGER 0..59  

dhcpClientExpireTimeSecond 1.3.6.1.4.1.1548.10.9.1.11
Time Client Lease expire time-second.
OBJECT-TYPE    
  INTEGER 0..59  

dhcpClientStatus 1.3.6.1.4.1.1548.10.9.1.12
The status column used for creating, modifying, and deleting instances of the columnar objects in this table.
OBJECT-TYPE    
  RowStatus  

dhcpClientValueTable 1.3.6.1.4.1.1548.10.10
The table used to set or clear Client DHCP option values.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpClientValueEntry

dhcpClientValueEntry 1.3.6.1.4.1.1548.10.10.1
OBJECT-TYPE    
  DhcpClientValueEntry  

dhcpClientValueCode 1.3.6.1.4.1.1548.10.10.1.1
DHCP Option Code as defined in rfc1533.
OBJECT-TYPE    
  INTEGER 0..255  

dhcpClientValueType 1.3.6.1.4.1.1548.10.10.1.2
Type of value for this DHCP Option Code.
OBJECT-TYPE    
  DhcpOptionType  

dhcpClientValue 1.3.6.1.4.1.1548.10.10.1.3
Value for this DHCP Option.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

dhcpClientValueStatus 1.3.6.1.4.1.1548.10.10.1.4
The status column used for creating, modifying, and deleting instances of the columnar objects in this table.
OBJECT-TYPE    
  RowStatus  

fpdir 1.3.6.1.4.1.1548.11
OBJECT IDENTIFIER    

fpDirTable 1.3.6.1.4.1.1548.11.1
The directory Table contains the names and sizes of the files in the file system.
OBJECT-TYPE    
  SEQUENCE OF  
    FpDirEntry

fpDirEntry 1.3.6.1.4.1.1548.11.1.1
Each entry contains the directory name in msdos format; 8 character name, followed by a ., followed by a 3 character extension. The file size is returned (in bytes).
OBJECT-TYPE    
  FpDirEntry  

fpDirIndex 1.3.6.1.4.1.1548.11.1.1.1
A file number to read.
OBJECT-TYPE    
  INTEGER 1..128  

fpDirName 1.3.6.1.4.1.1548.11.1.1.2
A textual description of the name of the file. In the format 8.3 for dos.
OBJECT-TYPE    
  DisplayString SIZE(0..12)  

fpDirSize 1.3.6.1.4.1.1548.11.1.1.3
The size of the file in bytes.
OBJECT-TYPE    
  INTEGER  

fpatm 1.3.6.1.4.1.1548.12
OBJECT IDENTIFIER    

atmOperation 1.3.6.1.4.1.1548.12.1
Use this object to give commands to save, load or erase ATM configuration in FLASH memory.
OBJECT-TYPE    
  INTEGER save(1), load(2), erase(3)  

fpfr 1.3.6.1.4.1.1548.13
OBJECT IDENTIFIER    

frOperation 1.3.6.1.4.1.1548.13.1
Use this object to give commands to save, load or erase FR configuration in FLASH memory.
OBJECT-TYPE    
  INTEGER save(1), load(2), erase(3)  

Defined Objects

IpxNetAddress  
OCTET STRING SIZE(4)    

MacAddress  
OCTET STRING SIZE(6)    

ConnectionType  
INTEGER async(1), isdn(2), fr(3), dds(4), x25(5)    

AuthenProtoType  
INTEGER none(1), pap(2), chap(3)    

RowStatus  
INTEGER active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6)    

DhcpOptionType  
INTEGER none(1), byte(2), word(3), long(4), longint(5), binary(6), ipaddress(7), string(8)    

DodEntry  
SEQUENCE    
  INTEGER as dodTableID  
  DisplayString as dodDestinationName SIZE(0..20)  
  DisplayString as dodPassword SIZE(0..40)  
  AuthenProtoType as dodAuthenProtocol  
  INTEGER as dodMaxLinks  
  INTEGER as dodBWThreshold  
  ConnectionType as dodPreferType  
  INTEGER as dodTearDownTimer  
  IpAddress as dodSourceIPAddress  
  IpAddress as dodRemoteIPAddress  
  IpAddress as dodSourceIPMask  
  IpAddress as dodRemoteIPMask  
  IpxNetAddress as dodIPXNetAddress  
  Counter as dodIPFilters  
  Counter as dodIPXFilters  
  Counter as dodRemoteIPNets  
  Counter as dodRemoteIPXNets  
  Counter as dodRemoteIPXSAPs  
  INTEGER as dodRemoteMacState  
  Counter as dodRemoteMacs  
  INTEGER as dodLastActivityTime  
  INTEGER as dodTableOperation  
  INTEGER as dodMinLinks  
  INTEGER as dodBODType  
  INTEGER as dodIpOptRecvRIP  
  INTEGER as dodIpOptSendRIP  
  INTEGER as dodIpOptRecvRIPDefault  
  INTEGER as dodIpOptSendRIPDefault  
  INTEGER as dodIpOptKeepPrivate  
  INTEGER as dodBrOptUseStp  
  INTEGER as dodPPPOptUseLCPEcho  
  INTEGER as dodEntryIsDisabled  
  INTEGER as dodCallbackOption  
  INTEGER as dodSendDataAsVoice  
  DisplayString as dodIPXNetStrAddress SIZE(1..8)  
  DisplayString as dodOurSystemName SIZE(0..40)  
  DisplayString as dodOurPassword SIZE(0..40)  
  INTEGER as dodPPPCallbackOption  
  DisplayString as dodPPPCallbackInfo SIZE(0..40)  
  INTEGER as dodDontAuthenticate  
  INTEGER as dodIPAddressTranslation  
  INTEGER as dodIpOptRecvRIP1  
  INTEGER as dodIpOptSendRIP1  
  INTEGER as dodIpOptRecvRIP2  
  INTEGER as dodIpOptSendRIP2  
  INTEGER as dodProtocol  
  INTEGER as dodCompression  
  INTEGER as dodPasswordSpecified  
  INTEGER as dodOurPasswordSpecified  
  INTEGER as dodBlockNetBIOS  
  INTEGER as dodMtu  
  INTEGER as dodIpSlaveMode  
  INTEGER as dodReacquireIpAddr  
  INTEGER as dodIpxOptRIPSAP  

DodCallIDEntry  
SEQUENCE    
  ConnectionType as dodCallIDType  
  Counter as dodCallIDPhones  

DodPhoneEntry  
SEQUENCE    
  INTEGER as dodPhoneIndex  
  INTEGER as dodPhoneSpeed  
  DisplayString as dodPhoneNumber SIZE(0..30)  

DodRemoteMacEntry  
SEQUENCE    
  INTEGER as dodRemoteMacIndex  
  MacAddress as dodRemoteMacAddress  
  INTEGER as dodRemoteMacOperation  

DodRemoteIPNetEntry  
SEQUENCE    
  INTEGER as dodRemoteIPNetIndex  
  IpAddress as dodRemoteIPNetAddress  
  IpAddress as dodRemoteIPNetMask  
  INTEGER as dodRemoteIPNetHops  
  INTEGER as dodRemoteIPNetOperation  
  IpAddress as dodRemoteIPNetGateway  

DodRemoteIPXNetEntry  
SEQUENCE    
  INTEGER as dodRemoteIPXNetIndex  
  IpxNetAddress as dodRemoteIPXNetAddress  
  INTEGER as dodRemoteIPXNetMetric  
  INTEGER as dodRemoteIPXNetTicks  
  INTEGER as dodRemoteIPXNetOperation  
  DisplayString as dodRemoteIPXNetStrAddress SIZE(1..8)  

DodRemoteIPXSAPEntry  
SEQUENCE    
  INTEGER as dodRemoteIPXSAPIndex  
  DisplayString as dodRemoteIPXSAPName SIZE(0..48)  
  IpxNetAddress as dodRemoteIPXSAPNetAddress  
  MacAddress as dodRemoteIPXSAPNodeAddress  
  OCTET STRING as dodRemoteIPXSAPSocket SIZE(2)  
  OCTET STRING as dodRemoteIPXSAPType SIZE(2)  
  INTEGER as dodRemoteIPXSAPHops  
  INTEGER as dodRemoteIPXSAPOperation  
  DisplayString as dodRemoteIPXSAPStrNetAddress SIZE(1..8)  
  DisplayString as dodRemoteIPXSAPStrSocket SIZE(1..4)  
  DisplayString as dodRemoteIPXSAPStrType SIZE(1..4)  

DodIPFilterEntry  
SEQUENCE    
  INTEGER as dodIPFilterIndex  
  IpAddress as dodIPFilterDstNetAddr  
  IpAddress as dodIPFilterSrcNetAddr  
  INTEGER as dodIPFilterAllow  

DodIPXFilterEntry  
SEQUENCE    
  INTEGER as dodIPXFilterIndex  
  IpxNetAddress as dodIPXFilterDstNetAddr  
  MacAddress as dodIPXFilterDstNodeAddr  
  OCTET STRING as dodIPXFilterDstSocket SIZE(2)  
  IpxNetAddress as dodIPXFilterSrcNetAddr  
  MacAddress as dodIPXFilterSrcNodeAddr  
  OCTET STRING as dodIPXFilterSrcSocket SIZE(2)  
  INTEGER as dodIPXFilterAllow  

DodCallerEntry  
SEQUENCE    
  DisplayString as dodCallerNumber SIZE(0..30)  
  INTEGER as dodCallerOperation  

DodIPTranslationServerEntry  
SEQUENCE    
  IpAddress as dodIPTranslationServerIPAddress  
  OCTET STRING as dodIPTranslationProtocol SIZE(1)  
  OCTET STRING as dodIPFirstTranslationPort SIZE(2)  
  OCTET STRING as dodIPLastTranslationPort SIZE(2)  
  OCTET STRING as dodIPFirstPrivatePort SIZE(2)  
  RowStatus as dodIPTranslationStatus  

DodNatHostMappingEntry  
SEQUENCE    
  IpAddress as dodFirstPrivateIPAddress  
  IpAddress as dodLastPrivateIPAddress  
  IpAddress as dodFirstPublicIPAddress  
  RowStatus as dodNatHostMappingStatus  

FpEtherEntry  
SEQUENCE    
  INTEGER as fpPortNum  
  INTEGER as fpBridgeState  
  INTEGER as fpIpState  
  INTEGER as fpIpxState  
  IpAddress as fpIpNetAddress  
  IpAddress as fpIpNetMask  
  IpxNetAddress as fpIpxNetAddress  
  INTEGER as fpIpxFrameType  
  INTEGER as fpEtherIpOptRecvRIP  
  INTEGER as fpEtherIpOptSendRIP  
  INTEGER as fpEtherIpOptRecvRIPDefault  
  INTEGER as fpEtherIpOptSendRIPDefault  
  DisplayString as fpIpxStrNetAddress SIZE(1..8)  
  IpAddress as fpIpDefaultGateway  
  INTEGER as fpEtherIpOptRecvRIP1  
  INTEGER as fpEtherIpOptSendRIP1  
  INTEGER as fpEtherIpOptRecvRIP2  
  INTEGER as fpEtherIpOptSendRIP2  
  IpAddress as fpIpRIPMulticastAddress  
  INTEGER as fpNATState  
  INTEGER as fpMtu  

EtherNatHostMappingEntry  
SEQUENCE    
  IpAddress as etherFirstPrivateIPAddress  
  IpAddress as etherLastPrivateIPAddress  
  IpAddress as etherFirstPublicIPAddress  
  RowStatus as etherNatHostMappingStatus  

EtherIPTranslationServerEntry  
SEQUENCE    
  IpAddress as etherIPTranslationServerIPAddress  
  OCTET STRING as etherIPTranslationProtocol SIZE(1)  
  OCTET STRING as etherIPFirstTranslationPort SIZE(2)  
  OCTET STRING as etherIPLastTranslationPort SIZE(2)  
  OCTET STRING as etherIPFirstPrivatePort SIZE(2)  
  RowStatus as etherIPTranslationStatus  

FpIsdnSwitchEntry  
SEQUENCE    
  INTEGER as fpIsdnSwitchTypeIndex  

FpSysCallerIdEntry  
SEQUENCE    
  INTEGER as fpCallerIdEnabled  

FpUdpRelayEntry  
SEQUENCE    
  OCTET STRING as fpUdpRelayFirstPort SIZE(2)  
  OCTET STRING as fpUdpRelayLastPort SIZE(2)  
  IpAddress as fpUdpRelayIPAddress  
  RowStatus as fpUdpRelayStatus  

FpVoiceEntry  
SEQUENCE    
  INTEGER as fpVoiceIndex  
  DisplayString as fpVoicePort  

FpEchoEntry  
SEQUENCE    
  INTEGER as fpEchoIndex  
  DisplayString as fpEchoPort  

FpOptionEntry  
SEQUENCE    
  INTEGER as fpOptionIndex  
  DisplayString as fpOptionString  
  INTEGER as fpOptionAvailable  

FpLoginEntry  
SEQUENCE    
  INTEGER as fpLoginAction  

FpWanEntry  
SEQUENCE    
  INTEGER as fpWanIndex  
  INTEGER as fpWanInstantOutUtil  
  INTEGER as fpWanInstantInUtil  
  INTEGER as fpWanAvgOutUtil  
  INTEGER as fpWanAvgInUtil  
  DisplayString as fpWanRemoteName  
  INTEGER as fpWanRemoteTime  
  INTEGER as fpWanIfIndex  
  Gauge as fpWanOutSpeed  
  Gauge as fpWanInSpeed  

PotsEntry  
SEQUENCE    
  INTEGER as potsIndex  
  INTEGER as potsEnabled  
  INTEGER as potsOpMode  
  INTEGER as potsPreemptMode  
  INTEGER as potsAutoMode  
  INTEGER as potsPhoneCnt  
  DisplayString as potsLocalNumber SIZE(0..30)  
  DisplayString as potsRemoteNumber SIZE(0..30)  
  INTEGER as potsState  
  INTEGER as potsIsdnChannel  
  INTEGER as potsWanIndex  

PotsPhoneEntry  
SEQUENCE    
  DisplayString as potsPhoneNumber SIZE(0..30)  
  INTEGER as potsPhoneOperation  

SysIPTranslationServerEntry  
SEQUENCE    
  IpAddress as sysIPTranslationServerIPAddress  
  OCTET STRING as sysIPTranslationProtocol SIZE(1)  
  OCTET STRING as sysIPFirstTranslationPort SIZE(2)  
  OCTET STRING as sysIPLastTranslationPort SIZE(2)  
  OCTET STRING as sysIPFirstPrivatePort SIZE(2)  
  RowStatus as sysIPTranslationStatus  

SysNatHostMappingEntry  
SEQUENCE    
  IpAddress as sysFirstPrivateIPAddress  
  IpAddress as sysLastPrivateIPAddress  
  IpAddress as sysFirstPublicIPAddress  
  RowStatus as sysNatHostMappingStatus  

DhcpCodeEntry  
SEQUENCE    
  INTEGER as dhcpOptionCode  
  INTEGER as dhcpMinCount  
  INTEGER as dhcpMaxCount  
  DhcpOptionType as dhcpOptionType  
  RowStatus as dhcpOptionCodeStatus  

DhcpGlobalValueEntry  
SEQUENCE    
  INTEGER as dhcpGlobalValueCode  
  DhcpOptionType as dhcpGlobalValueType  
  OCTET STRING as dhcpGlobalValue SIZE(0..255)  
  RowStatus as dhcpGlobalValueStatus  

DhcpSubnetEntry  
SEQUENCE    
  IpAddress as dhcpSubnetAddress  
  IpAddress as dhcpSubnetMask  
  IpAddress as dhcpSubnetFirstIpAddress  
  IpAddress as dhcpSubnetLastIpAddress  
  IpAddress as dhcpSubnetTftpServer  
  DisplayString as dhcpSubnetTftpFile SIZE(0..255)  
  INTEGER as dhcpSubnetBootp  
  INTEGER as dhcpSubnetLeaseTime  
  RowStatus as dhcpSubnetStatus  
  INTEGER as dhcpSubnetConflictActions  

DhcpSubnetValueEntry  
SEQUENCE    
  INTEGER as dhcpSubnetValueCode  
  DhcpOptionType as dhcpSubnetValueType  
  OCTET STRING as dhcpSubnetValue SIZE(0..255)  
  RowStatus as dhcpSubnetValueStatus  

DhcpClientEntry  
SEQUENCE    
  IpAddress as dhcpClientAddress  
  IpAddress as dhcpClientTftpServer  
  DisplayString as dhcpClientTftpFile SIZE(0..255)  
  INTEGER as dhcpClientBootp  
  INTEGER as dhcpClientLeaseTime  
  INTEGER as dhcpClientExpireTimeYear  
  INTEGER as dhcpClientExpireTimeMonth 1..12  
  INTEGER as dhcpClientExpireTimeDay 1..31  
  INTEGER as dhcpClientExpireTimeHour 0..23  
  INTEGER as dhcpClientExpireTimeMinute 0..59  
  INTEGER as dhcpClientExpireTimeSecond 0..59  
  RowStatus as dhcpClientStatus  

DhcpClientValueEntry  
SEQUENCE    
  INTEGER as dhcpClientValueCode  
  DhcpOptionType as dhcpClientValueType  
  OCTET STRING as dhcpClientValue SIZE(0..255)  
  RowStatus as dhcpClientValueStatus  

FpDirEntry  
SEQUENCE    
  INTEGER as fpDirIndex  
  DisplayString as fpDirName SIZE(0..12)  
  INTEGER as fpDirSize