
| RFC1155-SMI | RFC-1212 | FOUNDRY-SN-ROOT-MIB |
| Counter | OBJECT-TYPE | snIpx |
| snIpxGen | 1.3.6.1.4.1.1991.1.2.1.1 | ||
| OBJECT IDENTIFIER | |||
| snIpxRoutingMode | 1.3.6.1.4.1.1991.1.2.1.1.1 | ||
| Enabled/Disabled System IPX Routing Mode status. | |||
| OBJECT-TYPE | |||
| RtrStatus | |||
| snIpxNetBiosFilterMode | 1.3.6.1.4.1.1991.1.2.1.1.2 | ||
| Enabled/Disabled NetBios Filter Mode status. | |||
| OBJECT-TYPE | |||
| RtrStatus | |||
| snIpxClearCache | 1.3.6.1.4.1.1991.1.2.1.1.3 | ||
| clear(1) will clear cache table. | |||
| OBJECT-TYPE | |||
| ClearStatus | |||
| snIpxClearRoute | 1.3.6.1.4.1.1991.1.2.1.1.4 | ||
| clear(1) will clear ipx route table. | |||
| OBJECT-TYPE | |||
| ClearStatus | |||
| snIpxClearTrafficCnts | 1.3.6.1.4.1.1991.1.2.1.1.5 | ||
| clear(1) will clear ipx all traffic counters. - snIpxRcvPktsCnt, snIpxFwdPktsCnt, snIpxRcvDropPktsCnt, snIpxTxDropPktsCnt, snIpxRcvFiltPktsCnt, snIpxTxFiltPktsCnt. | |||
| OBJECT-TYPE | |||
| ClearStatus | |||
| snIpxRcvPktsCnt | 1.3.6.1.4.1.1991.1.2.1.1.6 | ||
| IPX incoming packets counter. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snIpxTxPktsCnt | 1.3.6.1.4.1.1991.1.2.1.1.7 | ||
| IPX Outgoing packets counter. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snIpxFwdPktsCnt | 1.3.6.1.4.1.1991.1.2.1.1.8 | ||
| IPX forwarding packets counter. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snIpxRcvDropPktsCnt | 1.3.6.1.4.1.1991.1.2.1.1.9 | ||
| IPX receiving drop packets counter. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snIpxRcvFiltPktsCnt | 1.3.6.1.4.1.1991.1.2.1.1.10 | ||
| IPX receiving filter packets counter. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snIpxRipGblFiltList | 1.3.6.1.4.1.1991.1.2.1.1.11 | ||
| An IPX RIP Global Filter List. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..32) | ||
| snIpxRipFiltOnAllPort | 1.3.6.1.4.1.1991.1.2.1.1.12 | ||
| Apply the IPX RIP Global filter list snIpxRipGblFiltList to all interfaces. This object is used to add all RIP filter lists and delete all RIP filter lists to/from all ports. Prior to sending this command, snIpxRipGblFiltList must be ready. The values that can be written are: deleteAllInBound(2)...delete all in-bound filter lists from all ports. deleteAllOutBound(3)..delete all out-bound filter lists from all ports. addAllInBound(4)......add all in-bound filter lists to all ports. addAllOutBound(5).....add all out-bound filter lists to all ports. If set operation is failed, then a SET with value of (2)or(3) returns error 'GenError'. Deleted(2)&(3) go away immediately. The following values can be returned on reads: noSuch(0)...no such operation yet. valid(1)....set operation is done and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), deleteAllInBound(2), deleteAllOutBound(3), addAllInBound(4), addAllOutBound(5) | ||
| snIpxSapGblFiltList | 1.3.6.1.4.1.1991.1.2.1.1.13 | ||
| An IPX SAP Global Filter List. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..32) | ||
| snIpxSapFiltOnAllPort | 1.3.6.1.4.1.1991.1.2.1.1.14 | ||
| Apply the IPX SAP Global filter list snIpxSapGblFiltList to all interfaces. This object is used to add all RIP filter lists and delete all SAP filter lists to/from all ports. Prior to sending this command, snIpxSapGblFiltList must be ready. The values that can be written are: deleteAllInBound(2)...delete all in-bound filter lists from all ports. deleteAllOutBound(3)..delete all out-bound filter lists from all ports. addAllInBound(4)......add all in-bound filter lists to all ports. addAllOutBound(5).....add all out-bound filter lists to all ports. If set operation is failed, then a SET with value of (2)or(3) returns error 'GenError'. Deleted(2)&(3) go away immediately. The following values can be returned on reads: noSuch(0)...no such operation yet. valid(1)....set operation is done and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), deleteAllInBound(2), deleteAllOutBound(3), addAllInBound(4), addAllOutBound(5) | ||
| snIpxTxDropPktsCnt | 1.3.6.1.4.1.1991.1.2.1.1.15 | ||
| IPX transmitting drop packets counter. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snIpxTxFiltPktsCnt | 1.3.6.1.4.1.1991.1.2.1.1.16 | ||
| IPX transmitting filter packets counter. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snIpxCache | 1.3.6.1.4.1.1991.1.2.1.2 | ||
| OBJECT IDENTIFIER | |||
| snIpxCacheTable | 1.3.6.1.4.1.1991.1.2.1.2.1 | ||
| IPX Cache table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnIpxCacheEntry | |||
| snIpxCacheEntry | 1.3.6.1.4.1.1991.1.2.1.2.1.1 | ||
| An entry in the IPX Cache table. | |||
| OBJECT-TYPE | |||
| SnIpxCacheEntry | |||
| snIpxCacheIndex | 1.3.6.1.4.1.1991.1.2.1.2.1.1.1 | ||
| The table index for a IPX Cache entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxCacheNetNum | 1.3.6.1.4.1.1991.1.2.1.2.1.1.2 | ||
| Cache Network number. | |||
| OBJECT-TYPE | |||
| NetNumber | |||
| snIpxCacheNode | 1.3.6.1.4.1.1991.1.2.1.2.1.1.3 | ||
| Cache Node Number. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| snIpxCacheOutFilter | 1.3.6.1.4.1.1991.1.2.1.2.1.1.4 | ||
| Cache Outbound Filter is ether disabled(0) or enabled(1). | |||
| OBJECT-TYPE | |||
| RtrStatus | |||
| snIpxCacheEncap | 1.3.6.1.4.1.1991.1.2.1.2.1.1.5 | ||
| The IPX encapsulation frame type. | |||
| OBJECT-TYPE | |||
| INTEGER | ethernetII(1), ethernet8022(2), ethernet8023(3), ethernetSnap(4) | ||
| snIpxCachePort | 1.3.6.1.4.1.1991.1.2.1.2.1.1.6 | ||
| IPX Router Port number. | |||
| OBJECT-TYPE | |||
| PortIndex | |||
| snIpxRoute | 1.3.6.1.4.1.1991.1.2.1.3 | ||
| OBJECT IDENTIFIER | |||
| snIpxRouteTable | 1.3.6.1.4.1.1991.1.2.1.3.1 | ||
| IPX route table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnIpxRouteEntry | |||
| snIpxRouteEntry | 1.3.6.1.4.1.1991.1.2.1.3.1.1 | ||
| An entry in the IPX route table. | |||
| OBJECT-TYPE | |||
| SnIpxRouteEntry | |||
| snIpxRouteIndex | 1.3.6.1.4.1.1991.1.2.1.3.1.1.1 | ||
| The table index for a IPX route entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxDestNetNum | 1.3.6.1.4.1.1991.1.2.1.3.1.1.2 | ||
| Destination Network number. | |||
| OBJECT-TYPE | |||
| NetNumber | |||
| snIpxFwdRouterNode | 1.3.6.1.4.1.1991.1.2.1.3.1.1.3 | ||
| Forward Router Node Number. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| snIpxDestHopCnts | 1.3.6.1.4.1.1991.1.2.1.3.1.1.4 | ||
| Number of hops to reach the destination. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxRouteMetric | 1.3.6.1.4.1.1991.1.2.1.3.1.1.5 | ||
| The metrics to next hop router. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxDestPort | 1.3.6.1.4.1.1991.1.2.1.3.1.1.6 | ||
| The destination port. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxServer | 1.3.6.1.4.1.1991.1.2.1.4 | ||
| OBJECT IDENTIFIER | |||
| snIpxServerTable | 1.3.6.1.4.1.1991.1.2.1.4.1 | ||
| IPX Server table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnIpxServerEntry | |||
| snIpxServerEntry | 1.3.6.1.4.1.1991.1.2.1.4.1.1 | ||
| An entry in the IPX Server table. | |||
| OBJECT-TYPE | |||
| SnIpxServerEntry | |||
| snIpxServerIndex | 1.3.6.1.4.1.1991.1.2.1.4.1.1.1 | ||
| The table index for a IPX Server entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxServerType | 1.3.6.1.4.1.1991.1.2.1.4.1.1.2 | ||
| IPX Server Type. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxServerNetNum | 1.3.6.1.4.1.1991.1.2.1.4.1.1.3 | ||
| Server Network number. | |||
| OBJECT-TYPE | |||
| NetNumber | |||
| snIpxServerNode | 1.3.6.1.4.1.1991.1.2.1.4.1.1.4 | ||
| Server Node Number. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| snIpxServerSocket | 1.3.6.1.4.1.1991.1.2.1.4.1.1.5 | ||
| Server Socket Number. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxServerHopCnts | 1.3.6.1.4.1.1991.1.2.1.4.1.1.6 | ||
| Number of intervening networks to reach the server. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxServerName | 1.3.6.1.4.1.1991.1.2.1.4.1.1.7 | ||
| IPX Server Name. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..47) | ||
| snIpxFwdFilter | 1.3.6.1.4.1.1991.1.2.1.5 | ||
| OBJECT IDENTIFIER | |||
| snIpxFwdFilterTable | 1.3.6.1.4.1.1991.1.2.1.5.1 | ||
| IPX Forward Filter table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnIpxFwdFilterEntry | |||
| snIpxFwdFilterEntry | 1.3.6.1.4.1.1991.1.2.1.5.1.1 | ||
| An entry in the IPX Forward Filter table. | |||
| OBJECT-TYPE | |||
| SnIpxFwdFilterEntry | |||
| snIpxFwdFilterId | 1.3.6.1.4.1.1991.1.2.1.5.1.1.1 | ||
| The filter ID for a filter entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxFwdFilterAction | 1.3.6.1.4.1.1991.1.2.1.5.1.1.2 | ||
| Action to take if the ipx packet match with this filter. | |||
| OBJECT-TYPE | |||
| Action | |||
| snIpxFwdFilterSocket | 1.3.6.1.4.1.1991.1.2.1.5.1.1.3 | ||
| IPX Forward Filter Socket Number. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxFwdFilterSrcNet | 1.3.6.1.4.1.1991.1.2.1.5.1.1.4 | ||
| Source Network Number. | |||
| OBJECT-TYPE | |||
| NetNumber | |||
| snIpxFwdFilterSrcNode | 1.3.6.1.4.1.1991.1.2.1.5.1.1.5 | ||
| Source Node Number. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| snIpxFwdFilterDestNet | 1.3.6.1.4.1.1991.1.2.1.5.1.1.6 | ||
| Destination Network Number. | |||
| OBJECT-TYPE | |||
| NetNumber | |||
| snIpxFwdFilterDestNode | 1.3.6.1.4.1.1991.1.2.1.5.1.1.7 | ||
| Destination Node Number. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| snIpxFwdFilterRowStatus | 1.3.6.1.4.1.1991.1.2.1.5.1.1.8 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snIpxRipFilter | 1.3.6.1.4.1.1991.1.2.1.6 | ||
| OBJECT IDENTIFIER | |||
| snIpxRipFilterTable | 1.3.6.1.4.1.1991.1.2.1.6.1 | ||
| IPX RIP Filter table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnIpxRipFilterEntry | |||
| snIpxRipFilterEntry | 1.3.6.1.4.1.1991.1.2.1.6.1.1 | ||
| An entry in the IPX RIP Filter table. | |||
| OBJECT-TYPE | |||
| SnIpxRipFilterEntry | |||
| snIpxRipFilterId | 1.3.6.1.4.1.1991.1.2.1.6.1.1.1 | ||
| The filter ID for a filter entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxRipFilterAction | 1.3.6.1.4.1.1991.1.2.1.6.1.1.2 | ||
| Action to take if the ipx packet match with this filter. | |||
| OBJECT-TYPE | |||
| Action | |||
| snIpxRipFilterNet | 1.3.6.1.4.1.1991.1.2.1.6.1.1.3 | ||
| IPX RIP Filter Network number. | |||
| OBJECT-TYPE | |||
| NetNumber | |||
| snIpxRipFilterMask | 1.3.6.1.4.1.1991.1.2.1.6.1.1.4 | ||
| IPX RIP Filter Network/Subnet Mask. | |||
| OBJECT-TYPE | |||
| NetNumber | |||
| snIpxRipFilterRowStatus | 1.3.6.1.4.1.1991.1.2.1.6.1.1.5 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snIpxSapFilter | 1.3.6.1.4.1.1991.1.2.1.7 | ||
| OBJECT IDENTIFIER | |||
| snIpxSapFilterTable | 1.3.6.1.4.1.1991.1.2.1.7.1 | ||
| IPX SAP Filter table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnIpxSapFilterEntry | |||
| snIpxSapFilterEntry | 1.3.6.1.4.1.1991.1.2.1.7.1.1 | ||
| An entry in the IPX SAP Filter table. | |||
| OBJECT-TYPE | |||
| SnIpxSapFilterEntry | |||
| snIpxSapFilterId | 1.3.6.1.4.1.1991.1.2.1.7.1.1.1 | ||
| The filter ID for a filter entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxSapFilterAction | 1.3.6.1.4.1.1991.1.2.1.7.1.1.2 | ||
| Action to take if the ipx packet match with this filter. | |||
| OBJECT-TYPE | |||
| Action | |||
| snIpxSapFilterType | 1.3.6.1.4.1.1991.1.2.1.7.1.1.3 | ||
| IPX SAP Filter type to be matched. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxSapFilterName | 1.3.6.1.4.1.1991.1.2.1.7.1.1.4 | ||
| IPX SAP Filter Name. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..47) | ||
| snIpxSapFilterRowStatus | 1.3.6.1.4.1.1991.1.2.1.7.1.1.5 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snIpxIfFwdAccess | 1.3.6.1.4.1.1991.1.2.1.8 | ||
| OBJECT IDENTIFIER | |||
| snIpxIfFwdAccessTable | 1.3.6.1.4.1.1991.1.2.1.8.1 | ||
| IPX IF Forward Access table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnIpxIfFwdAccessEntry | |||
| snIpxIfFwdAccessEntry | 1.3.6.1.4.1.1991.1.2.1.8.1.1 | ||
| An entry in the IPX Forward Access table. | |||
| OBJECT-TYPE | |||
| SnIpxIfFwdAccessEntry | |||
| snIpxIfFwdAccessPort | 1.3.6.1.4.1.1991.1.2.1.8.1.1.1 | ||
| The IPX interface to which the Forward Filter applies. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxIfFwdAccessDir | 1.3.6.1.4.1.1991.1.2.1.8.1.1.2 | ||
| The access direction of incoming packet filter or outgoing packet filter. | |||
| OBJECT-TYPE | |||
| INTEGER | in(1), out(2) | ||
| snIpxIfFwdAccessFilterList | 1.3.6.1.4.1.1991.1.2.1.8.1.1.3 | ||
| An IPX IF Forward Filter List. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..32) | ||
| snIpxIfFwdAccessRowStatus | 1.3.6.1.4.1.1991.1.2.1.8.1.1.4 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snIpxIfRipAccess | 1.3.6.1.4.1.1991.1.2.1.9 | ||
| OBJECT IDENTIFIER | |||
| snIpxIfRipAccessTable | 1.3.6.1.4.1.1991.1.2.1.9.1 | ||
| IPX IF RIP Access table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnIpxIfRipAccessEntry | |||
| snIpxIfRipAccessEntry | 1.3.6.1.4.1.1991.1.2.1.9.1.1 | ||
| An entry in the IPX Forward Access table. | |||
| OBJECT-TYPE | |||
| SnIpxIfRipAccessEntry | |||
| snIpxIfRipAccessPort | 1.3.6.1.4.1.1991.1.2.1.9.1.1.1 | ||
| The IPX interface to which the RIP Filter applies. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxIfRipAccessDir | 1.3.6.1.4.1.1991.1.2.1.9.1.1.2 | ||
| The access direction of incoming packet filter or outgoing packet filter. | |||
| OBJECT-TYPE | |||
| INTEGER | in(1), out(2) | ||
| snIpxIfRipAccessFilterList | 1.3.6.1.4.1.1991.1.2.1.9.1.1.3 | ||
| An IPX IF RIP Access Filter List. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..32) | ||
| snIpxIfRipAccessRowStatus | 1.3.6.1.4.1.1991.1.2.1.9.1.1.4 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snIpxIfSapAccess | 1.3.6.1.4.1.1991.1.2.1.10 | ||
| OBJECT IDENTIFIER | |||
| snIpxIfSapAccessTable | 1.3.6.1.4.1.1991.1.2.1.10.1 | ||
| IPX IF RIP Access table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnIpxIfSapAccessEntry | |||
| snIpxIfSapAccessEntry | 1.3.6.1.4.1.1991.1.2.1.10.1.1 | ||
| An entry in the IPX Forward Access table. | |||
| OBJECT-TYPE | |||
| SnIpxIfSapAccessEntry | |||
| snIpxIfSapAccessPort | 1.3.6.1.4.1.1991.1.2.1.10.1.1.1 | ||
| The IPX interface to which the SAP Filter applies. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snIpxIfSapAccessDir | 1.3.6.1.4.1.1991.1.2.1.10.1.1.2 | ||
| The access direction of incoming packet filter or outgoing packet filter. | |||
| OBJECT-TYPE | |||
| INTEGER | in(1), out(2) | ||
| snIpxIfSapAccessFilterList | 1.3.6.1.4.1.1991.1.2.1.10.1.1.3 | ||
| An IPX IF SAP Access Filter List. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..32) | ||
| snIpxIfSapAccessRowStatus | 1.3.6.1.4.1.1991.1.2.1.10.1.1.4 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snIpxPortAddr | 1.3.6.1.4.1.1991.1.2.1.11 | ||
| OBJECT IDENTIFIER | |||
| snIpxPortAddrTable | 1.3.6.1.4.1.1991.1.2.1.11.1 | ||
| IPX port address table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnIpxPortAddrEntry | |||
| snIpxPortAddrEntry | 1.3.6.1.4.1.1991.1.2.1.11.1.1 | ||
| An entry in the IPX Port Address table. | |||
| OBJECT-TYPE | |||
| SnIpxPortAddrEntry | |||
| snIpxPortAddrPort | 1.3.6.1.4.1.1991.1.2.1.11.1.1.1 | ||
| The port index for port address entry. | |||
| OBJECT-TYPE | |||
| PortIndex | |||
| snIpxPortAddrEncap | 1.3.6.1.4.1.1991.1.2.1.11.1.1.2 | ||
| The IPX encapsulation type. ethernet8022(1), ethernet8023(2), ethernetII(3), ethernetSnap(4) Note: Each Network Number can be assigned with one unique Frame type; Otherwise, a SNMP-SET error will be returned. | |||
| OBJECT-TYPE | |||
| INTEGER | ethernet8022(1), ethernet8023(2), ethernetII(3), ethernetSnap(4) | ||
| snIpxPortAddrNetNum | 1.3.6.1.4.1.1991.1.2.1.11.1.1.3 | ||
| An unique Network number for the IPX interface port. | |||
| OBJECT-TYPE | |||
| NetNumber | |||
| snIpxPortAddrRowStatus | 1.3.6.1.4.1.1991.1.2.1.11.1.1.4 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snIpxPortAddrNetBiosFilterMode | 1.3.6.1.4.1.1991.1.2.1.11.1.1.5 | ||
| Enabled/Disabled NetBios Filter Mode status per Port Address entry. | |||
| OBJECT-TYPE | |||
| RtrStatus | |||
| snIpxPortCounters | 1.3.6.1.4.1.1991.1.2.1.12 | ||
| OBJECT IDENTIFIER | |||
| snIpxPortCountersTable | 1.3.6.1.4.1.1991.1.2.1.12.1 | ||
| IPX port Counters table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnIpxPortCountersEntry | |||
| snIpxPortCountersEntry | 1.3.6.1.4.1.1991.1.2.1.12.1.1 | ||
| An entry in the IPX Port Counters table. | |||
| OBJECT-TYPE | |||
| SnIpxPortCountersEntry | |||
| snIpxPortCountersPort | 1.3.6.1.4.1.1991.1.2.1.12.1.1.1 | ||
| The port index for port Counters entry. | |||
| OBJECT-TYPE | |||
| PortIndex | |||
| snIpxPortCountersRcvPktsCnt | 1.3.6.1.4.1.1991.1.2.1.12.1.1.2 | ||
| IPX incoming packets counter for the interface. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snIpxPortCountersTxPktsCnt | 1.3.6.1.4.1.1991.1.2.1.12.1.1.3 | ||
| IPX Outgoing packets counter for the interface. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snIpxPortCountersFwdPktsCnt | 1.3.6.1.4.1.1991.1.2.1.12.1.1.4 | ||
| IPX forwarding packets counter for the interface. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snIpxPortCountersRcvDropPktsCnt | 1.3.6.1.4.1.1991.1.2.1.12.1.1.5 | ||
| IPX receiving drop packets counter for the interface. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snIpxPortCountersTxDropPktsCnt | 1.3.6.1.4.1.1991.1.2.1.12.1.1.6 | ||
| IPX transmitting drop packets counter for the interface. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snIpxPortCountersRcvFiltPktsCnt | 1.3.6.1.4.1.1991.1.2.1.12.1.1.7 | ||
| IPX receiving filter packets counter for the interface. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snIpxPortCountersTxFiltPktsCnt | 1.3.6.1.4.1.1991.1.2.1.12.1.1.8 | ||
| IPX transmitting filter packets counter for the interface. | |||
| OBJECT-TYPE | |||
| Counter | |||
| RtrStatus | |||
| INTEGER | disabled(0), enabled(1) | ||
| ClearStatus | |||
| INTEGER | normal(0), clear(1) | ||
| PortIndex | |||
| INTEGER | 1..3900 | ||
| Action | |||
| INTEGER | deny(0), permit(1) | ||
| PhysAddress | |||
| OCTET STRING | |||
| NetNumber | |||
| OCTET STRING | SIZE(4) | ||
| SnIpxCacheEntry | |||
| SEQUENCE | |||
| INTEGER as snIpxCacheIndex | |||
| NetNumber as snIpxCacheNetNum | |||
| PhysAddress as snIpxCacheNode | |||
| RtrStatus as snIpxCacheOutFilter | |||
| INTEGER as snIpxCacheEncap | |||
| PortIndex as snIpxCachePort | |||
| SnIpxRouteEntry | |||
| SEQUENCE | |||
| INTEGER as snIpxRouteIndex | |||
| NetNumber as snIpxDestNetNum | |||
| PhysAddress as snIpxFwdRouterNode | |||
| INTEGER as snIpxDestHopCnts | |||
| INTEGER as snIpxRouteMetric | |||
| INTEGER as snIpxDestPort | |||
| SnIpxServerEntry | |||
| SEQUENCE | |||
| INTEGER as snIpxServerIndex | |||
| INTEGER as snIpxServerType | |||
| NetNumber as snIpxServerNetNum | |||
| PhysAddress as snIpxServerNode | |||
| INTEGER as snIpxServerSocket | |||
| INTEGER as snIpxServerHopCnts | |||
| OCTET STRING as snIpxServerName | |||
| SnIpxFwdFilterEntry | |||
| SEQUENCE | |||
| INTEGER as snIpxFwdFilterId | |||
| Action as snIpxFwdFilterAction | |||
| INTEGER as snIpxFwdFilterSocket | |||
| NetNumber as snIpxFwdFilterSrcNet | |||
| PhysAddress as snIpxFwdFilterSrcNode | |||
| NetNumber as snIpxFwdFilterDestNet | |||
| PhysAddress as snIpxFwdFilterDestNode | |||
| INTEGER as snIpxFwdFilterRowStatus | |||
| SnIpxRipFilterEntry | |||
| SEQUENCE | |||
| INTEGER as snIpxRipFilterId | |||
| Action as snIpxRipFilterAction | |||
| NetNumber as snIpxRipFilterNet | |||
| NetNumber as snIpxRipFilterMask | |||
| INTEGER as snIpxRipFilterRowStatus | |||
| SnIpxSapFilterEntry | |||
| SEQUENCE | |||
| INTEGER as snIpxSapFilterId | |||
| Action as snIpxSapFilterAction | |||
| INTEGER as snIpxSapFilterType | |||
| OCTET STRING as snIpxSapFilterName | |||
| INTEGER as snIpxSapFilterRowStatus | |||
| SnIpxIfFwdAccessEntry | |||
| SEQUENCE | |||
| INTEGER as snIpxIfFwdAccessPort | |||
| INTEGER as snIpxIfFwdAccessDir | |||
| OCTET STRING as snIpxIfFwdAccessFilterList | |||
| INTEGER as snIpxIfFwdAccessRowStatus | |||
| SnIpxIfRipAccessEntry | |||
| SEQUENCE | |||
| INTEGER as snIpxIfRipAccessPort | |||
| INTEGER as snIpxIfRipAccessDir | |||
| OCTET STRING as snIpxIfRipAccessFilterList | |||
| INTEGER as snIpxIfRipAccessRowStatus | |||
| SnIpxIfSapAccessEntry | |||
| SEQUENCE | |||
| INTEGER as snIpxIfSapAccessPort | |||
| INTEGER as snIpxIfSapAccessDir | |||
| OCTET STRING as snIpxIfSapAccessFilterList | |||
| INTEGER as snIpxIfSapAccessRowStatus | |||
| SnIpxPortAddrEntry | |||
| SEQUENCE | |||
| PortIndex as snIpxPortAddrPort | |||
| INTEGER as snIpxPortAddrEncap | |||
| NetNumber as snIpxPortAddrNetNum | |||
| INTEGER as snIpxPortAddrRowStatus | |||
| RtrStatus as snIpxPortAddrNetBiosFilterMode | |||
| SnIpxPortCountersEntry | |||
| SEQUENCE | |||
| PortIndex as snIpxPortCountersPort | |||
| Counter as snIpxPortCountersRcvPktsCnt | |||
| Counter as snIpxPortCountersTxPktsCnt | |||
| Counter as snIpxPortCountersFwdPktsCnt | |||
| Counter as snIpxPortCountersRcvDropPktsCnt | |||
| Counter as snIpxPortCountersTxDropPktsCnt | |||
| Counter as snIpxPortCountersRcvFiltPktsCnt | |||
| Counter as snIpxPortCountersTxFiltPktsCnt | |||