Fore-TCM-MIB

File: Fore-TCM-MIB.mib (66186 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC Fore-Common-MIB
Fore-TrapLog-MIB

Imported symbols

Counter32 Gauge32 IpAddress
TimeTicks Integer32 OBJECT-TYPE
NOTIFICATION-TYPE MODULE-IDENTITY DateAndTime
TimeInterval DisplayString PhysAddress
EntryStatus hardware atmSwitch
trapLogIndex

Defined Objects

ecpOperatingModeChange 1.3.6.1.4.1.326.2.2.0.1050
This trap indicates that the Extended Control Processor (ECP) has change operating state.
NOTIFICATION-TYPE    
  ecpBoardIndex  
  ecpOperatingStatus  
  trapLogIndex  

esiTimingSourceChange 1.3.6.1.4.1.326.2.2.0.1051
This trap is generated whenever the External Synchronization Interface (ESI) timing source (esiCurrentTimingRef) is changed either manually or by the system due to failure detection.
NOTIFICATION-TYPE    
  esiCardIndex  
  esiCurrentTimingRef  
  esiRefSource  
  trapLogIndex  

esiTimingSourceFailed 1.3.6.1.4.1.326.2.2.0.1052
This trap is generated whenever the External Synchronization Interface (ESI) timing source (esiCurrentTimingRef) fails.
NOTIFICATION-TYPE    
  esiCardIndex  
  esiCurrentTimingRef  
  esiRefSource  
  trapLogIndex  

ecpStandbyFailed 1.3.6.1.4.1.326.2.2.0.1076
This trap is generated whenever the Standby Timing Control Module (TCM) appears to haved failed. This is determined by lack of response from it.
NOTIFICATION-TYPE    
  ecpBoardIndex  
  trapLogIndex  

ecpStationModule 1.3.6.1.4.1.326.2.2.1.7
The Timing Control Module (TCM).
MODULE-IDENTITY    

ecpHardware 1.3.6.1.4.1.326.2.2.1.7.1
OBJECT IDENTIFIER    

ecpBoardTable 1.3.6.1.4.1.326.2.2.1.7.1.1
This table contains Extended Control Processor (ECP) board information.
OBJECT-TYPE    
  SEQUENCE OF  
    EcpBoardEntry

ecpBoardEntry 1.3.6.1.4.1.326.2.2.1.7.1.1.1
This entry contains Extended Control Processor (ECP) board information
OBJECT-TYPE    
  EcpBoardEntry  

ecpBoardIndex 1.3.6.1.4.1.326.2.2.1.7.1.1.1.1
This is the Extended Control Processor board index within the management station.
OBJECT-TYPE    
  INTEGER slotX(1), slotY(2)  

ecpBoardVersion 1.3.6.1.4.1.326.2.2.1.7.1.1.1.2
This is the version number of this Extended Control Processor (ECP) board.
OBJECT-TYPE    
  Integer32  

ecpBoardSerialNumber 1.3.6.1.4.1.326.2.2.1.7.1.1.1.3
This is the serial number of this Extended Control Processor (ECP) board.
OBJECT-TYPE    
  Integer32  

ecpBoardOtherEcpPresent 1.3.6.1.4.1.326.2.2.1.7.1.1.1.4
This is the other ECP board present indicator for this Extended Control Processor (ECP) board.
OBJECT-TYPE    
  INTEGER ecpPresent(1), ecpAbsent(2)  

ecpBoardEsiPresent 1.3.6.1.4.1.326.2.2.1.7.1.1.1.5
This is the External Synchronization Interface (ESI) present indicator for this Extended Control Processor (ECP) board.
OBJECT-TYPE    
  INTEGER esiPresent(1), esiAbsent(2)  

ecpSerialIfTable 1.3.6.1.4.1.326.2.2.1.7.1.2
This table contains the serial port interface information for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  SEQUENCE OF  
    EcpSerialIfEntry

ecpSerialIfEntry 1.3.6.1.4.1.326.2.2.1.7.1.2.1
This entry contains the serial port interface information for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  EcpSerialIfEntry  

ecpSerialIfPortIndex 1.3.6.1.4.1.326.2.2.1.7.1.2.1.1
This is the serial port interface index for this port on the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  Integer32  

ecpSerialIfPortType 1.3.6.1.4.1.326.2.2.1.7.1.2.1.2
This is the serial port interface type for this port on the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  INTEGER other(1), rs232(2), rs422(3), rs423(4), v35(5), x21(6)  

ecpSerialIfPortSpeed 1.3.6.1.4.1.326.2.2.1.7.1.2.1.3
This is the serial port interface speed for this port on the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  Integer32  

ecpSerialIfFlowType 1.3.6.1.4.1.326.2.2.1.7.1.2.1.4
This is the serial port interface flow control for this port on the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  INTEGER none(1), ctsRts(2), dsrDtr(3)  

ecpSerialIfPortBits 1.3.6.1.4.1.326.2.2.1.7.1.2.1.5
This is the serial port interface character size for this port on the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  Integer32  

ecpSerialIfPortStopBits 1.3.6.1.4.1.326.2.2.1.7.1.2.1.6
This is the serial port interface stop bit count for this port on the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  INTEGER one(1), two(2), oneAndHalf(3), dynamic(4)  

ecpSerialIfPortParity 1.3.6.1.4.1.326.2.2.1.7.1.2.1.7
This is the serial port interface character parity for this port on the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  INTEGER none(1), odd(2), even(3), mark(4), space(5)  

ecpEnvironment 1.3.6.1.4.1.326.2.2.1.7.1.3
OBJECT IDENTIFIER    

ecpAlarmGroup 1.3.6.1.4.1.326.2.2.1.7.1.3.1
OBJECT IDENTIFIER    

ecpAlarmTable 1.3.6.1.4.1.326.2.2.1.7.1.3.1.1
A table of switch alarm definitions and configuration.
OBJECT-TYPE    
  SEQUENCE OF  
    EcpAlarmEntry

ecpAlarmEntry 1.3.6.1.4.1.326.2.2.1.7.1.3.1.1.1
A table entry containing switch alarm definitions.
OBJECT-TYPE    
  EcpAlarmEntry  

ecpAlarmType 1.3.6.1.4.1.326.2.2.1.7.1.3.1.1.1.1
The type of the alarm.
OBJECT-TYPE    
  INTEGER powerSupplyInputFailed(1), powerSupplyOutputFailed(2), fanBankFailed(3), tempSensorOverTemp(4), linkFailed(5), spansFailed(6), powerSupplyOverCurrent(7), powerSupply5VoltFailed(8), faultyOrMissingStandbyTcm(9), esiLossOfSyncSrc(10)  

ecpAlarmStatus 1.3.6.1.4.1.326.2.2.1.7.1.3.1.1.1.2
The status of this alarm entry. An alarm becomes active if the underlying condition is detected. For power supplies, the input failed alarm condition is asserted if the input voltage is not within the nominal range for the supply. This does not necessarily mean that an ouput failure will result. A power supply output failure condition is asserted if any power supply is failing or if it is physically removed. Power supply output alarms are only applicable to switches with multiple power supplies. Fan bank and temperature sensor failures are applicable only to switches with the appropriate sensing capabilities. Link and spans failures are applicable to all switches.
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

ecpAlarmMinorCategory 1.3.6.1.4.1.326.2.2.1.7.1.3.1.1.1.3
This object indicates whether a minor alarm is triggered when this event occurs.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ecpAlarmMajorCategory 1.3.6.1.4.1.326.2.2.1.7.1.3.1.1.1.4
This object indicates whether a major alarm is triggered when this event occurs.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ecpAlarmReset 1.3.6.1.4.1.326.2.2.1.7.1.3.1.1.1.5
The manager may set this to the value zero to cancel a current alarm. This is useful for silencing alarms triggered via edge detection. If this variable is readable, then the alarm is resettable.
OBJECT-TYPE    
  Integer32  

ecpAlarmMajorRelayState 1.3.6.1.4.1.326.2.2.1.7.1.3.1.2
This object indicates the current state of the major alarm relay. If one or more of the alarms (ecpAlarmType) that are defined major (ecpAlarmMajorCategory) are currently active (ecpAlarmStatus), this object will be on(1).
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ecpAlarmMinorRelayState 1.3.6.1.4.1.326.2.2.1.7.1.3.1.3
This object indicates the current state of the minor alarm relay. Ifone or mote of the alarms (ecpAlarmType) that are defined minor (ecpAlarmMinorCategory) are currently active (ecpAlarmStatus), this object will be on(1).
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ecpAlarmRelayTable 1.3.6.1.4.1.326.2.2.1.7.1.3.1.4
This table contains the alarm relay definitions for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  SEQUENCE OF  
    EcpAlarmRelayEntry

ecpAlarmRelayEntry 1.3.6.1.4.1.326.2.2.1.7.1.3.1.4.1
This entry contains the alarm relay definitions for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  EcpAlarmRelayEntry  

ecpAlarmRelayIndex 1.3.6.1.4.1.326.2.2.1.7.1.3.1.4.1.1
This is the index of the alarm relay on the Extended Control Processor (ECP). The Raven ECP has 5 addressable alarm relays (1-5).
OBJECT-TYPE    
  Integer32  

ecpAlarmRelayFunction 1.3.6.1.4.1.326.2.2.1.7.1.3.1.4.1.2
This is the alarm function associated with an alarm relay on the Extended Control Processor (ECP). An alarm relay may either be unused, assigned to the major alarm, or assigned to the minor alarm.
OBJECT-TYPE    
  INTEGER ecpUnusedRelay(1), ecpMajorAlarmRelay(2), ecpMinorAlarmRelay(3)  

ecpAlarmRelayState 1.3.6.1.4.1.326.2.2.1.7.1.3.1.4.1.3
This is the current state of the alarm relay on the Extended Control Processor (ECP). The state 'on' means that the alarm relay is activated; the state 'off' means that it is deactivated.
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ecpSoftware 1.3.6.1.4.1.326.2.2.1.7.2
OBJECT IDENTIFIER    

ecpSwMainGroup 1.3.6.1.4.1.326.2.2.1.7.2.1
OBJECT IDENTIFIER    

ecpSwMainTable 1.3.6.1.4.1.326.2.2.1.7.2.1.1
The table contains the Extended Control Processor (ECP) information maintained by the control software.
OBJECT-TYPE    
  SEQUENCE OF  
    EcpSwMainEntry

ecpSwMainEntry 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1
This entry contains the Extended Control Processor (ECP) information maintained by the control software.
OBJECT-TYPE    
  EcpSwMainEntry  

ecpName 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.1
This is the system name of this Extended Control Processor (ECP) platform.
OBJECT-TYPE    
  DisplayString  

ecpHardwareVersion 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.2
This is the hardware version of the Extended Control Processor (ECP) platform.
OBJECT-TYPE    
  Integer32  

ecpSoftwareVersion 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.3
This is the software version of the Extended Control Processor (ECP) control software. The version is encoded into 6 hex characters. Version 1.2.3 would be 0x010203.
OBJECT-TYPE    
  Integer32  

ecpSoftwareVersionText 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.4
This is the software version text of the Extended Control Processor (ECP) control software. This object contains information regarding the software configuration that was used to build this software.
OBJECT-TYPE    
  DisplayString  

ecpType 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.5
This is the type of the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  INTEGER unrecognized(1), cec-plus(2), cec-plus-t(3)  

ecpOperatingStatus 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.6
This is the software status of this Extended Control Processor (ECP).
OBJECT-TYPE    
  INTEGER ecpUnknown(1), ecpStandby(2), ecpActive(3), ecpOffline(4)  

ecpProtocolType 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.7
The transfer protocol that is used when upgrading the software, saving/restoring the CDB, etc. on this Extended Control Processor (ECP) board.
OBJECT-TYPE    
  INTEGER tftp(1), ftp(2)  

ecpTimeZone 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.8
The TimeZone configured for this Extended Control Processor (ECP). This variable follows the POSIX standard 1003.1-1988 for the format of the TZ environment variable. In particular, it is general enough to specify the rules for converting from Standard to Daylight Savings time for most timezones of the world. By default, the ECP has the rules built in for the following timezones: EST5EDT CST6CDT MST7MDT PST8PDT AKST9AKDT. Locales outside of these timezones will need to supply the appropriate rule for switching between Daylight and Standard time.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

ecpGMTime 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.9
The Extended Control Processor's (ECP's) notion of Greenwich Mean Time. Linked to hrSystemDate. Offset part of time spec, if supplied, is considered an error.
OBJECT-TYPE    
  DateAndTime  

ecpUptime 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.10
This is the amount of time that the Extended Control Processor (ECP) control software has been running, in hundredths of a second.
OBJECT-TYPE    
  TimeTicks  

ecpModeChangeTime 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.11
This is the time that the Extended Control Processor (ECP) control software has switched to the current operating mode.
OBJECT-TYPE    
  DateAndTime  

ecpOtherEcpStatus 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.12
This is the software status of the other Extended Control Processor (ECP) from the viewpoint of this ECP.
OBJECT-TYPE    
  INTEGER ecpNormal(1), ecpUnknown(2)  

ecpExternalInput1 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.13
This is the state of External Input #1 from the viewpoint of the Extended Control Processor (ECP).
OBJECT-TYPE    
  INTEGER ecpInputOn(1), ecpInputOff(2)  

ecpExternalInput2 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.14
This is the state of External Input #2 from the viewpoint of the Extended Control Processor (ECP).
OBJECT-TYPE    
  INTEGER ecpInputOn(1), ecpInputOff(2)  

ecpExternalInput3 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.15
This is the state of External Input #3 from the viewpoint of the Extended Control Processor (ECP).
OBJECT-TYPE    
  INTEGER ecpInputOn(1), ecpInputOff(2)  

ecpExternalInput4 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.16
This is the state of External Input #4 from the viewpoint of the Extended Control Processor (ECP).
OBJECT-TYPE    
  INTEGER ecpInputOn(1), ecpInputOff(2)  

ecpExternalInput5 1.3.6.1.4.1.326.2.2.1.7.2.1.1.1.17
This is the state of External Input #5 from the viewpoint of the Extended Control Processor (ECP).
OBJECT-TYPE    
  INTEGER ecpInputOn(1), ecpInputOff(2)  

ecpIpGroup 1.3.6.1.4.1.326.2.2.1.7.2.2
OBJECT IDENTIFIER    

ecpNetIfTable 1.3.6.1.4.1.326.2.2.1.7.2.2.1
This table contains the network interface information for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  SEQUENCE OF  
    EcpNetIfEntry

ecpNetIfEntry 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1
This entry contains the network interface information for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  EcpNetIfEntry  

ecpNetIfIndex 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.1
A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
OBJECT-TYPE    
  Integer32  

ecpNetIfDescr 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.2
A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the hardware interface.
OBJECT-TYPE    
  DisplayString  

ecpNetIfPhysAddress 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.3
The interface's address at the protocol layer immediately `below' the network layer in the protocol stack. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length.
OBJECT-TYPE    
  PhysAddress  

ecpNetIfAdminStatus 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.4
The desired state of the interface.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

ecpNetIfOperStatus 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.5
The current operational state of the interface.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

ecpNetIfLastChange 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.6
The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.
OBJECT-TYPE    
  TimeTicks  

ecpNetIfIpAddr 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.7
The IP address associated with this network interface.
OBJECT-TYPE    
  IpAddress  

ecpNetIfIpMask 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.8
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
OBJECT-TYPE    
  IpAddress  

ecpNetIfIpBcastAddr 1.3.6.1.4.1.326.2.2.1.7.2.2.1.1.9
The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface.
OBJECT-TYPE    
  Integer32  

ecpNetIfStatsTable 1.3.6.1.4.1.326.2.2.1.7.2.2.2
This table contains the network interface statistics for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  SEQUENCE OF  
    EcpNetIfStatsEntry

ecpNetIfStatsEntry 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1
This entry contains the network interface statistics for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  EcpNetIfStatsEntry  

ecpNetIfInOctets 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.1
The total number of octets received on the interface, including framing characters.
OBJECT-TYPE    
  Counter32  

ecpNetIfInUcastPkts 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.2
The number of subnetwork-unicast packets delivered to a higher-layer protocol.
OBJECT-TYPE    
  Counter32  

ecpNetIfInNUcastPkts 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.3
The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol.
OBJECT-TYPE    
  Counter32  

ecpNetIfInDiscards 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.4
The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
OBJECT-TYPE    
  Counter32  

ecpNetIfInErrors 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.5
The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol.
OBJECT-TYPE    
  Counter32  

ecpNetIfInUnknownProtos 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.6
The number of packets received via the interface which were discarded because of an unknown or unsupported protocol.
OBJECT-TYPE    
  Counter32  

ecpNetIfOutOctets 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.7
The total number of octets transmitted out of the interface, including framing characters.
OBJECT-TYPE    
  Counter32  

ecpNetIfOutUcastPkts 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.8
The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.
OBJECT-TYPE    
  Counter32  

ecpNetIfOutNUcastPkts 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.9
The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent.
OBJECT-TYPE    
  Counter32  

ecpNetIfOutDiscards 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.10
The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
OBJECT-TYPE    
  Counter32  

ecpNetIfOutErrors 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.11
The number of outbound packets that could not be transmitted because of errors.
OBJECT-TYPE    
  Counter32  

ecpNetIfOutQLen 1.3.6.1.4.1.326.2.2.1.7.2.2.2.1.12
The length of the output packet queue (in packets).
OBJECT-TYPE    
  Gauge32  

ecpIpStatsTable 1.3.6.1.4.1.326.2.2.1.7.2.2.3
This table contains the Internet protocol statistics for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  SEQUENCE OF  
    EcpIpStatsEntry

ecpIpStatsEntry 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1
This entry contains the Internet protocol statistics for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  EcpIpStatsEntry  

ecpIpInReceives 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.1
The total number of input datagrams received from interfaces, including those received in error.
OBJECT-TYPE    
  Counter32  

ecpIpInHdrErrors 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.2
The number of input datagrams discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IP options, etc.
OBJECT-TYPE    
  Counter32  

ecpIpInAddrErrors 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.3
The number of input datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., 0.0.0.0) and addresses of unsupported Classes (e.g., Class E). For entities which are not IP Gateways and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address.
OBJECT-TYPE    
  Counter32  

ecpIpForwDatagrams 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.4
The number of input datagrams for which this entity was not their final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as IP Gateways, this counter will include only those packets which were Source-Routed via this entity, and the Source- Route option processing was successful.
OBJECT-TYPE    
  Counter32  

ecpIpInUnknownProtos 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.5
The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol.
OBJECT-TYPE    
  Counter32  

ecpIpInDiscards 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.6
The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly.
OBJECT-TYPE    
  Counter32  

ecpIpInDelivers 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.7
The total number of input datagrams successfully delivered to IP user-protocols (including ICMP).
OBJECT-TYPE    
  Counter32  

ecpIpOutRequests 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.8
The total number of IP datagrams which local IP user-protocols (including ICMP) supplied to IP in requests for transmission. Note that this counter does not include any datagrams counted in ipForwDatagrams.
OBJECT-TYPE    
  Counter32  

ecpIpOutDiscards 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.9
The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in ipForwDatagrams if any such packets met this (discretionary) discard criterion.
OBJECT-TYPE    
  Counter32  

ecpIpOutNoRoutes 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.10
The number of IP datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets counted in ipForwDatagrams which meet this `no-route' criterion. Note that this includes any datagarms which a host cannot route because all of its default gateways are down.
OBJECT-TYPE    
  Counter32  

ecpIpReasmReqds 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.11
The number of IP fragments received which needed to be reassembled at this entity.
OBJECT-TYPE    
  Counter32  

ecpIpReasmOKs 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.12
The number of IP datagrams successfully re- assembled.
OBJECT-TYPE    
  Counter32  

ecpIpReasmFails 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.13
The number of failures detected by the IP re- assembly algorithm (for whatever reason: timed out, errors, etc). Note that this is not necessarily a count of discarded IP fragments since some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments by combining them as they are received.
OBJECT-TYPE    
  Counter32  

ecpIpFragOKs 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.14
The number of IP datagrams that have been successfully fragmented at this entity.
OBJECT-TYPE    
  Counter32  

ecpIpFragFails 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.15
The number of IP datagrams that have been discarded because they needed to be fragmented at this entity but could not be, e.g., because their Don't Fragment flag was set.
OBJECT-TYPE    
  Counter32  

ecpIpFragCreates 1.3.6.1.4.1.326.2.2.1.7.2.2.3.1.16
The number of IP datagram fragments that have been generated as a result of fragmentation at this entity.
OBJECT-TYPE    
  Counter32  

ecpIpRouteTable 1.3.6.1.4.1.326.2.2.1.7.2.2.4
This table contains the Internet Protocol routing entries for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  SEQUENCE OF  
    EcpIpRouteEntry

ecpIpRouteEntry 1.3.6.1.4.1.326.2.2.1.7.2.2.4.1
This entry contains the Internet Protocol routing data for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  EcpIpRouteEntry  

ecpIpRouteDest 1.3.6.1.4.1.326.2.2.1.7.2.2.4.1.1
The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.
OBJECT-TYPE    
  IpAddress  

ecpIpRouteIfIndex 1.3.6.1.4.1.326.2.2.1.7.2.2.4.1.2
The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
OBJECT-TYPE    
  Integer32  

ecpIpRouteNextHop 1.3.6.1.4.1.326.2.2.1.7.2.2.4.1.3
The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.)
OBJECT-TYPE    
  IpAddress  

ecpIpRouteMetric1 1.3.6.1.4.1.326.2.2.1.7.2.2.4.1.4
The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
OBJECT-TYPE    
  Integer32  

ecpIpRouteType 1.3.6.1.4.1.326.2.2.1.7.2.2.4.1.5
The type of route. Note that the values direct(3) and indirect(4) refer to the notion of direct and indirect routing in the IP architecture. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipRouteType object.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), direct(3), indirect(4)  

ecpIpRouteMask 1.3.6.1.4.1.326.2.2.1.7.2.2.4.1.6
Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipRouteMask by determining whether the value of the correspondent ipRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the ipRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.
OBJECT-TYPE    
  IpAddress  

ecpIcmpStatsTable 1.3.6.1.4.1.326.2.2.1.7.2.2.5
This table contains the Internet Control Message Protocol statistics for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  SEQUENCE OF  
    EcpIcmpStatsEntry

ecpIcmpStatsEntry 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1
This entry contains the Internet Control Message Protocol statistics for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  EcpIcmpStatsEntry  

ecpIcmpInMsgs 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.1
The total number of ICMP messages which the entity received. Note that this counter includes all those counted by icmpInErrors.
OBJECT-TYPE    
  Counter32  

ecpIcmpInErrors 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.2
The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.).
OBJECT-TYPE    
  Counter32  

ecpIcmpInDestUnreach 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.3
The number of ICMP Destination Unreachable messages received.
OBJECT-TYPE    
  Counter32  

ecpIcmpInTimeExcds 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.4
The number of ICMP Time Exceeded messages received.
OBJECT-TYPE    
  Counter32  

ecpIcmpInParmProbs 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.5
The number of ICMP Parameter Problem messages received.
OBJECT-TYPE    
  Counter32  

ecpIcmpInSrcQuenchs 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.6
The number of ICMP Source Quench messages received.
OBJECT-TYPE    
  Counter32  

ecpIcmpInRedirects 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.7
The number of ICMP Redirect messages received.
OBJECT-TYPE    
  Counter32  

ecpIcmpInEchos 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.8
The number of ICMP Echo (request) messages received.
OBJECT-TYPE    
  Counter32  

ecpIcmpInEchoReps 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.9
The number of ICMP Echo Reply messages received.
OBJECT-TYPE    
  Counter32  

ecpIcmpInTimestamps 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.10
The number of ICMP Timestamp (request) messages received.
OBJECT-TYPE    
  Counter32  

ecpIcmpInTimestampReps 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.11
The number of ICMP Timestamp Reply messages received.
OBJECT-TYPE    
  Counter32  

ecpIcmpInaddrMasks 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.12
The number of ICMP Address Mask Request messages received.
OBJECT-TYPE    
  Counter32  

ecpIcmpInAddrMaskReps 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.13
The number of ICMP Address Mask Reply messages received.
OBJECT-TYPE    
  Counter32  

ecpIcmpOutMsgs 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.14
The total number of ICMP messages which this entity attempted to send. Note that this counter includes all those counted by icmpOutErrors.
OBJECT-TYPE    
  Counter32  

ecpIcmpOutErrors 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.15
The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there may be no types of error which contribute to this counter's value.
OBJECT-TYPE    
  Counter32  

ecpIcmpOutDestUnreachs 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.16
The number of ICMP Destination Unreachable messages sent.
OBJECT-TYPE    
  Counter32  

ecpIcmpOutTimeExcds 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.17
The number of ICMP Time Exceeded messages sent.
OBJECT-TYPE    
  Counter32  

ecpIcmpOutParmProbs 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.18
The number of ICMP Parameter Problem messages sent.
OBJECT-TYPE    
  Counter32  

ecpIcmpOutSrcQuenchs 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.19
The number of ICMP Source Quench messages sent.
OBJECT-TYPE    
  Counter32  

ecpIcmpOutRedirects 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.20
The number of ICMP Redirect messages sent. For a host, this object will always be zero, since hosts do not send redirects.
OBJECT-TYPE    
  Counter32  

ecpIcmpOutEchos 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.21
The number of ICMP Echo (request) messages sent.
OBJECT-TYPE    
  Counter32  

ecpIcmpOutEchoReps 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.22
The number of ICMP Echo Reply messages sent.
OBJECT-TYPE    
  Counter32  

ecpIcmpOutTimestamps 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.23
The number of ICMP Timestamp (request) messages sent.
OBJECT-TYPE    
  Counter32  

ecpIcmpOutTimestampReps 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.24
The number of ICMP Timestamp Reply messages sent.
OBJECT-TYPE    
  Counter32  

ecpIcmpOutAddrMasks 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.25
The number of ICMP Address Mask Request messages sent.
OBJECT-TYPE    
  Counter32  

ecpIcmpOutAddrMaskReps 1.3.6.1.4.1.326.2.2.1.7.2.2.5.1.26
The number of ICMP Address Mask Reply messages sent.
OBJECT-TYPE    
  Counter32  

ecpTcpStatsTable 1.3.6.1.4.1.326.2.2.1.7.2.2.6
This table contains the Transmission Control Protocol statistics for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  SEQUENCE OF  
    EcpTcpStatsEntry

ecpTcpStatsEntry 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1
This entry contains the Transmission Control Protocol statistics for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  EcpTcpStatsEntry  

ecpTcpActiveOpens 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.1
The number of times TCP connections have made a direct transition to the SYN-SENT state from the CLOSED state.
OBJECT-TYPE    
  Counter32  

ecpTcpPassiveOpens 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.2
The number of times TCP connections have made a direct transition to the SYN-RCVD state from the LISTEN state.
OBJECT-TYPE    
  Counter32  

ecpTcpAttemptFails 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.3
The number of times TCP connections have made a direct transition to the CLOSED state from either the SYN-SENT state or the SYN-RCVD state, plus the number of times TCP connections have made a direct transition to the LISTEN state from the SYN-RCVD state.
OBJECT-TYPE    
  Counter32  

ecpTcpEstabResets 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.4
The number of times TCP connections have made a direct transition to the CLOSED state from either the ESTABLISHED state or the CLOSE-WAIT state.
OBJECT-TYPE    
  Counter32  

ecpTcpCurrEstab 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.5
The number of TCP connections for which the current state is either ESTABLISHED or CLOSE- WAIT.
OBJECT-TYPE    
  Counter32  

ecpTcpInSegs 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.6
The total number of segments received, including those received in error. This count includes segments received on currently established connections.
OBJECT-TYPE    
  Counter32  

ecpTcpOutSegs 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.7
The total number of segments sent, including those on current connections but excluding those containing only retransmitted octets.
OBJECT-TYPE    
  Counter32  

ecpTcpRetransSegs 1.3.6.1.4.1.326.2.2.1.7.2.2.6.1.8
The total number of segments retransmitted - that is, the number of TCP segments transmitted containing one or more previously transmitted octets.
OBJECT-TYPE    
  Counter32  

ecpUdpStatsTable 1.3.6.1.4.1.326.2.2.1.7.2.2.7
This table contains the User Datagram Protocol statistics for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  SEQUENCE OF  
    EcpUdpStatsEntry

ecpUdpStatsEntry 1.3.6.1.4.1.326.2.2.1.7.2.2.7.1
This entry contains the User Datagram Protocol statistics for the Extended Control Processor (ECP) board.
OBJECT-TYPE    
  EcpUdpStatsEntry  

ecpUdpInDatagrams 1.3.6.1.4.1.326.2.2.1.7.2.2.7.1.1
The total number of UDP datagrams delivered to UDP users.
OBJECT-TYPE    
  Counter32  

ecpUdpNoPorts 1.3.6.1.4.1.326.2.2.1.7.2.2.7.1.2
The total number of received UDP datagrams for which there was no application at the destination port.
OBJECT-TYPE    
  Counter32  

ecpUdpInErrors 1.3.6.1.4.1.326.2.2.1.7.2.2.7.1.3
The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port.
OBJECT-TYPE    
  Counter32  

ecpUdpOutDatagrams 1.3.6.1.4.1.326.2.2.1.7.2.2.7.1.4
The total number of UDP datagrams sent from this entity.
OBJECT-TYPE    
  Counter32  

ecpIpConfigTable 1.3.6.1.4.1.326.2.2.1.7.2.2.8
IP Configuration table for the TCMs
OBJECT-TYPE    
  SEQUENCE OF  
    EcpIpConfigEntry

ecpIpConfigEntry 1.3.6.1.4.1.326.2.2.1.7.2.2.8.1
IP Configuration table entry for the TCMs
OBJECT-TYPE    
  EcpIpConfigEntry  

ecpIpForwarding 1.3.6.1.4.1.326.2.2.1.7.2.2.8.1.1
The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to change this object to an inappropriate value.
OBJECT-TYPE    
  INTEGER forwarding(1), not-forwarding(2)  

ecpSnmp 1.3.6.1.4.1.326.2.2.1.7.2.3
OBJECT IDENTIFIER    

ecpTrapConfGroup 1.3.6.1.4.1.326.2.2.1.7.2.3.1
OBJECT IDENTIFIER    

ecpTrapNumberOfDest 1.3.6.1.4.1.326.2.2.1.7.2.3.1.1
The current number of configured trap destinations. All traps are sent to all destinations.
OBJECT-TYPE    
  Integer32  

ecpTrapDestTable 1.3.6.1.4.1.326.2.2.1.7.2.3.1.2
A table of destinations to which the agent sends traps.
OBJECT-TYPE    
  SEQUENCE OF  
    EcpTrapDestEntry

ecpTrapDestEntry 1.3.6.1.4.1.326.2.2.1.7.2.3.1.2.1
A table entry containing address of a management station, to which the agent sends traps.
OBJECT-TYPE    
  EcpTrapDestEntry  

ecpTrapDest 1.3.6.1.4.1.326.2.2.1.7.2.3.1.2.1.1
Address to which the agent sends traps. Usually a network management station sets this address to itself.
OBJECT-TYPE    
  IpAddress  

ecpTrapDestStatus 1.3.6.1.4.1.326.2.2.1.7.2.3.1.2.1.2
The status of this trap destination entry.
OBJECT-TYPE    
  EntryStatus  

esiCard 1.3.6.1.4.1.326.2.2.1.8
OBJECT IDENTIFIER    

esiHardware 1.3.6.1.4.1.326.2.2.1.8.1
OBJECT IDENTIFIER    

esiCardHwTable 1.3.6.1.4.1.326.2.2.1.8.1.1
This table contains the hardware information for the External Synchronization Interface (ESI) cards.
OBJECT-TYPE    
  SEQUENCE OF  
    EsiCardHwEntry

esiCardHwEntry 1.3.6.1.4.1.326.2.2.1.8.1.1.1
This table entry contains the hardware information for a single External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  EsiCardHwEntry  

esiCardIndex 1.3.6.1.4.1.326.2.2.1.8.1.1.1.1
This is the index for this External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  INTEGER slotX(1), slotY(2)  

esiHwCardType 1.3.6.1.4.1.326.2.2.1.8.1.1.1.2
This is the card type for this External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  INTEGER esiDs1TypeA(1), esiDs1TypeB(2), esiE1TypeA(3), esiE1TypeB(4)  

esiHwCardVersion 1.3.6.1.4.1.326.2.2.1.8.1.1.1.3
This is the card version for this External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  Integer32  

esiHwPllStatus 1.3.6.1.4.1.326.2.2.1.8.1.1.1.4
This is the card phase-locked loop (PLL) status for this External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  INTEGER pllFreeRun(1), pllLocked(2), pllAcquire(3), pllHoldover(4), pllRefQualFail(5)  

esiSoftware 1.3.6.1.4.1.326.2.2.1.8.2
OBJECT IDENTIFIER    

esiCardSwTable 1.3.6.1.4.1.326.2.2.1.8.2.1
This table contains the software information for the External Synchronization Interface (ESI) cards.
OBJECT-TYPE    
  SEQUENCE OF  
    EsiCardSwEntry

esiCardSwEntry 1.3.6.1.4.1.326.2.2.1.8.2.1.1
This table entry contains the software information for a single External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  EsiCardSwEntry  

esiOperationStatus 1.3.6.1.4.1.326.2.2.1.8.2.1.1.1
This is the operation status of the clock output for this External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

esiCurrentTimingRef 1.3.6.1.4.1.326.2.2.1.8.2.1.1.2
This is the current timing reference in use for this External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  INTEGER refFreeRun(1), refIsPrimary(2), refIsSecondary(3), refIsBits1(5), refIsBits2(6)  

esiRequestedTimingRef 1.3.6.1.4.1.326.2.2.1.8.2.1.1.3
This is the timing reference requested to be used for this External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  INTEGER requestFreeRun(1), requestPrimary(2), requestSecondary(3), requestAutomatic(4), requestBits(5)  

esiPrimaryRefSource 1.3.6.1.4.1.326.2.2.1.8.2.1.1.4
This is the primary timing reference source for this External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  EsiReferenceSource  

esiSecondaryRefSource 1.3.6.1.4.1.326.2.2.1.8.2.1.1.5
This is the secondary timing reference source for this External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  EsiReferenceSource  

esiCurrentFaultBits 1.3.6.1.4.1.326.2.2.1.8.2.1.1.6
This is the current state of the fault bits presented by this External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  Integer32  

esiBitsFramingFormat 1.3.6.1.4.1.326.2.2.1.8.2.1.1.7
This is the framing format of the BITS interface for this External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  INTEGER d4(1), esf(2), mfas(3), mfascrc4(4), fas(5), fascrc4(6)  

esiBitsCodingFormat 1.3.6.1.4.1.326.2.2.1.8.2.1.1.8
This is the coding format of the BITS interface for this External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  INTEGER ami(1), b8zs(2), hdb3(3)  

esiBitsOutputLevel 1.3.6.1.4.1.326.2.2.1.8.2.1.1.9
This is the output level (dB) of the DS1 BITS interface for this External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  INTEGER esiDs1Level0-6(1), esiDs1Level1-2(2), esiDs1Level1-8(3), esiDs1Level2-4(4), esiDs1Level3-0(5)  

esiRevertiveSwitching 1.3.6.1.4.1.326.2.2.1.8.2.1.1.10
This is the status of the revertive switching for timing sources on this External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

esiRevertiveDelay 1.3.6.1.4.1.326.2.2.1.8.2.1.1.11
This is the amount of time after the restoration of the primary timing reference before the External Synchronization Interface (ESI) card will be instructed to return to the primary timing reference. This value is truncated to whole seconds.
OBJECT-TYPE    
  TimeInterval  

esiSwitchingDelay 1.3.6.1.4.1.326.2.2.1.8.2.1.1.12
This is the amount of time after the failure of a timing reference before the External Synchronization Interface (ESI) card will be instructed to switch to the next available timing reference. This value is truncated to whole seconds.
OBJECT-TYPE    
  TimeInterval  

esiReferenceTable 1.3.6.1.4.1.326.2.2.1.8.2.2
This table contains the timing reference source information for the External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  SEQUENCE OF  
    EsiReferenceEntry

esiReferenceEntry 1.3.6.1.4.1.326.2.2.1.8.2.2.1
This table entry contains the timing reference source information for a single External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  EsiReferenceEntry  

esiRefSource 1.3.6.1.4.1.326.2.2.1.8.2.2.1.1
This is the timing reference source index for the External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  EsiReferenceSource  

esiRefSourceText 1.3.6.1.4.1.326.2.2.1.8.2.2.1.2
This is a textual description of the timing reference source that is provided to the External Synchronization Interface (ESI) card.
OBJECT-TYPE    
  DisplayString  

esiRefSourceStatus 1.3.6.1.4.1.326.2.2.1.8.2.2.1.3
This is the status of the timing reference source that is provided to the External Synchornization Interface (ESI) card.
OBJECT-TYPE    
  INTEGER available(1), unavailable(2)  

esiRefSourceAdminStatus 1.3.6.1.4.1.326.2.2.1.8.2.2.1.4
This is the admin status of the timing reference source that is provided to the External Synchornization Interface (ESI) card.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

esiRefSourceQualStatus 1.3.6.1.4.1.326.2.2.1.8.2.2.1.5
This is the RefQual status of the timing reference source that is provided to the External Synchornization Interface (ESI) card.
OBJECT-TYPE    
  INTEGER ok(1), fail(2)  

Defined Objects

EsiReferenceSource  
INTEGER fab1Pri(1), fab1Sec(2), fab2Pri(3), fab2Sec(4), fab3Pri(5), fab3Sec(6), fab4Pri(7), fab4Sec(8), bits1(9), bits2(10)    

EcpBoardEntry  
SEQUENCE    
  INTEGER as ecpBoardIndex  
  Integer32 as ecpBoardVersion  
  Integer32 as ecpBoardSerialNumber  
  INTEGER as ecpBoardOtherEcpPresent  
  INTEGER as ecpBoardEsiPresent  

EcpSerialIfEntry  
SEQUENCE    
  Integer32 as ecpSerialIfPortIndex  
  INTEGER as ecpSerialIfPortType  
  Integer32 as ecpSerialIfPortSpeed  
  INTEGER as ecpSerialIfFlowType  
  Integer32 as ecpSerialIfPortBits  
  INTEGER as ecpSerialIfPortStopBits  
  INTEGER as ecpSerialIfPortParity  

EcpAlarmEntry  
SEQUENCE    
  INTEGER as ecpAlarmType  
  INTEGER as ecpAlarmStatus  
  INTEGER as ecpAlarmMinorCategory  
  INTEGER as ecpAlarmMajorCategory  
  Integer32 as ecpAlarmReset  

EcpAlarmRelayEntry  
SEQUENCE    
  Integer32 as ecpAlarmRelayIndex  
  INTEGER as ecpAlarmRelayFunction  
  INTEGER as ecpAlarmRelayState  

EcpSwMainEntry  
SEQUENCE    
  DisplayString as ecpName  
  Integer32 as ecpHardwareVersion  
  Integer32 as ecpSoftwareVersion  
  DisplayString as ecpSoftwareVersionText  
  INTEGER as ecpType  
  INTEGER as ecpOperatingStatus  
  INTEGER as ecpProtocolType  
  DisplayString as ecpTimeZone  
  DateAndTime as ecpGMTime  
  TimeTicks as ecpUptime  
  DateAndTime as ecpModeChangeTime  
  INTEGER as ecpOtherEcpStatus  
  INTEGER as ecpExternalInput1  
  INTEGER as ecpExternalInput2  
  INTEGER as ecpExternalInput3  
  INTEGER as ecpExternalInput4  
  INTEGER as ecpExternalInput5  

EcpNetIfEntry  
SEQUENCE    
  Integer32 as ecpNetIfIndex  
  DisplayString as ecpNetIfDescr  
  PhysAddress as ecpNetIfPhysAddress  
  INTEGER as ecpNetIfAdminStatus  
  INTEGER as ecpNetIfOperStatus  
  TimeTicks as ecpNetIfLastChange  
  IpAddress as ecpNetIfIpAddr  
  IpAddress as ecpNetIfIpMask  
  Integer32 as ecpNetIfIpBcastAddr  

EcpNetIfStatsEntry  
SEQUENCE    
  Counter32 as ecpNetIfInOctets  
  Counter32 as ecpNetIfInUcastPkts  
  Counter32 as ecpNetIfInNUcastPkts  
  Counter32 as ecpNetIfInDiscards  
  Counter32 as ecpNetIfInErrors  
  Counter32 as ecpNetIfInUnknownProtos  
  Counter32 as ecpNetIfOutOctets  
  Counter32 as ecpNetIfOutUcastPkts  
  Counter32 as ecpNetIfOutNUcastPkts  
  Counter32 as ecpNetIfOutDiscards  
  Counter32 as ecpNetIfOutErrors  
  Gauge32 as ecpNetIfOutQLen  

EcpIpStatsEntry  
SEQUENCE    
  Counter32 as ecpIpInReceives  
  Counter32 as ecpIpInHdrErrors  
  Counter32 as ecpIpInAddrErrors  
  Counter32 as ecpIpForwDatagrams  
  Counter32 as ecpIpInUnknownProtos  
  Counter32 as ecpIpInDiscards  
  Counter32 as ecpIpInDelivers  
  Counter32 as ecpIpOutRequests  
  Counter32 as ecpIpOutDiscards  
  Counter32 as ecpIpOutNoRoutes  
  Counter32 as ecpIpReasmReqds  
  Counter32 as ecpIpReasmOKs  
  Counter32 as ecpIpReasmFails  
  Counter32 as ecpIpFragOKs  
  Counter32 as ecpIpFragFails  
  Counter32 as ecpIpFragCreates  

EcpIpRouteEntry  
SEQUENCE    
  IpAddress as ecpIpRouteDest  
  Integer32 as ecpIpRouteIfIndex  
  IpAddress as ecpIpRouteNextHop  
  Integer32 as ecpIpRouteMetric1  
  INTEGER as ecpIpRouteType  
  IpAddress as ecpIpRouteMask  

EcpIcmpStatsEntry  
SEQUENCE    
  Counter32 as ecpIcmpInMsgs  
  Counter32 as ecpIcmpInErrors  
  Counter32 as ecpIcmpInDestUnreach  
  Counter32 as ecpIcmpInTimeExcds  
  Counter32 as ecpIcmpInParmProbs  
  Counter32 as ecpIcmpInSrcQuenchs  
  Counter32 as ecpIcmpInRedirects  
  Counter32 as ecpIcmpInEchos  
  Counter32 as ecpIcmpInEchoReps  
  Counter32 as ecpIcmpInTimestamps  
  Counter32 as ecpIcmpInTimestampReps  
  Counter32 as ecpIcmpInaddrMasks  
  Counter32 as ecpIcmpInAddrMaskReps  
  Counter32 as ecpIcmpOutMsgs  
  Counter32 as ecpIcmpOutErrors  
  Counter32 as ecpIcmpOutDestUnreachs  
  Counter32 as ecpIcmpOutTimeExcds  
  Counter32 as ecpIcmpOutParmProbs  
  Counter32 as ecpIcmpOutSrcQuenchs  
  Counter32 as ecpIcmpOutRedirects  
  Counter32 as ecpIcmpOutEchos  
  Counter32 as ecpIcmpOutEchoReps  
  Counter32 as ecpIcmpOutTimestamps  
  Counter32 as ecpIcmpOutTimestampReps  
  Counter32 as ecpIcmpOutAddrMasks  
  Counter32 as ecpIcmpOutAddrMaskReps  

EcpTcpStatsEntry  
SEQUENCE    
  Counter32 as ecpTcpActiveOpens  
  Counter32 as ecpTcpPassiveOpens  
  Counter32 as ecpTcpAttemptFails  
  Counter32 as ecpTcpEstabResets  
  Counter32 as ecpTcpCurrEstab  
  Counter32 as ecpTcpInSegs  
  Counter32 as ecpTcpOutSegs  
  Counter32 as ecpTcpRetransSegs  

EcpUdpStatsEntry  
SEQUENCE    
  Counter32 as ecpUdpInDatagrams  
  Counter32 as ecpUdpNoPorts  
  Counter32 as ecpUdpInErrors  
  Counter32 as ecpUdpOutDatagrams  

EcpIpConfigEntry  
SEQUENCE    
  INTEGER as ecpIpForwarding  

EcpTrapDestEntry  
SEQUENCE    
  IpAddress as ecpTrapDest  
  EntryStatus as ecpTrapDestStatus  

EsiCardHwEntry  
SEQUENCE    
  INTEGER as esiCardIndex  
  INTEGER as esiHwCardType  
  Integer32 as esiHwCardVersion  
  INTEGER as esiHwPllStatus  

EsiCardSwEntry  
SEQUENCE    
  INTEGER as esiOperationStatus  
  INTEGER as esiCurrentTimingRef  
  INTEGER as esiRequestedTimingRef  
  EsiReferenceSource as esiPrimaryRefSource  
  EsiReferenceSource as esiSecondaryRefSource  
  Integer32 as esiCurrentFaultBits  
  INTEGER as esiBitsFramingFormat  
  INTEGER as esiBitsCodingFormat  
  INTEGER as esiBitsOutputLevel  
  INTEGER as esiRevertiveSwitching  
  TimeInterval as esiRevertiveDelay  
  TimeInterval as esiSwitchingDelay  

EsiReferenceEntry  
SEQUENCE    
  EsiReferenceSource as esiRefSource  
  DisplayString as esiRefSourceText  
  INTEGER as esiRefSourceStatus  
  INTEGER as esiRefSourceAdminStatus  
  INTEGER as esiRefSourceQualStatus