GDCMDM-MIB

File: GDCMDM-MIB.mib (80532 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
RFC-1215 GDCMACRO-MIB

Imported symbols

enterprises TimeTicks DisplayString
OBJECT-TYPE TRAP-TYPE SCinstance

Defined Objects

gdc 1.3.6.1.4.1.498
OBJECT IDENTIFIER    

mdm 1.3.6.1.4.1.498.4
OBJECT IDENTIFIER    

mdmNetworkConfigTable 1.3.6.1.4.1.498.4.1
The GDC VFAST modem network configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmNetworkEntry

mdmCallStatsTrap 1.3.6.1.4.1.498.4.1
This is the Call Statistics Trap. When a V.F 28.8 modem disconnects from a call after data has passed, it will send call statistics information.
TRAP-TYPE    
  mdmDCERate  
  mdmRetrainCount  
  mdmFallbackCount  
  mdmFallforwardCount  
  mdmRxSignalLevel  
  mdmSignaltoNoiseRatio  
  mdmAnswerOriginateStat  
  mdmCallDurationStat  
  mdmDiscReason  
  mdmCompressionEfficiency  
  mdmThruput  

mdmNetworkEntry 1.3.6.1.4.1.498.4.1.1
A listing of GDC VFAST modem network options.
OBJECT-TYPE    
  MdmNetworkEntry  

mdmNetworkIndex 1.3.6.1.4.1.498.4.1.1.1
A unique index for the Network Table.
OBJECT-TYPE    
  SCinstance  

mdmNetworkType 1.3.6.1.4.1.498.4.1.1.2
Command to option the VF line type mode of operation.
OBJECT-TYPE    
  INTEGER switchedNetwork(1), privateLine2Wire(2), privateLine4Wire(3)  

mdmSNTxType 1.3.6.1.4.1.498.4.1.1.3
Command used to select either Permissive or Programable Switched Network Transmit Level. This object is Country Code dependent
OBJECT-TYPE    
  INTEGER permissive(1), programmable(2), adjustable(3)  

mdmSNTxLevel 1.3.6.1.4.1.498.4.1.1.4
Command to select(force) the Switched Network Transmit Level when modem is optioned for adjustable. This object is Country Code dependent
OBJECT-TYPE    
  INTEGER 0..15  

mdmSNHandshakeMode 1.3.6.1.4.1.498.4.1.1.5
Available handshake modes. This object is Country Code dependent.
OBJECT-TYPE    
  INTEGER gdcVfastAuto(1), gdcVfastOnly(2), v32bisAuto(3), v32bisOnly(4), v32Auto(5), v32Only(6), v22bis(7), v22Only(8), bell212(9), bell103(10), v21(11)  

mdmDTEConfigTable 1.3.6.1.4.1.498.4.2
The GDC VFAST modem Data Terminal Equipment configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmDTEntry

mdmDTEntry 1.3.6.1.4.1.498.4.2.1
A listing of GDC VFAST modem DTE options.
OBJECT-TYPE    
  MdmDTEntry  

mdmDTEIndex 1.3.6.1.4.1.498.4.2.1.1
A unique index for the DTE Table.
OBJECT-TYPE    
  SCinstance  

mdmDTESpeed 1.3.6.1.4.1.498.4.2.1.2
This option selects DTE bit Rate.
OBJECT-TYPE    
  INTEGER autobaud(1), lastAT(2), bps300(3), bps1200(4), bps2400(5), bps4800(6), bps7200(7), bps9600(8), bps12000(9), bps14400(10), bps16800(11), bps19200(12), bps21600(13), bps24000(14), bps26400(15), bps28800(16), bps38400(17), bps57600(18), bps76800(19), bps115200(20), bps128000(21)  

mdmCPMResp 1.3.6.1.4.1.498.4.2.1.3
Selects the response rate of the Call Progress Monitor.
OBJECT-TYPE    
  INTEGER autobaud(1), lastConnectSpeed(2), bps300(3), bps1200(4), bps2400(5), bps4800(6), bps7200(7), bps9600(8), bps12000(9), bps14400(10), bps16800(11), bps19200(12), bps21600(13), bps24000(14), bps26400(15), bps28800(16), bps38400(17), bps57600(18), bps76800(19), bps115200(20), bps128000(21)  

mdmCharLength 1.3.6.1.4.1.498.4.2.1.4
DTE charater length and format options of the DTE asynchronous data.
OBJECT-TYPE    
  INTEGER data6Stop1(1), data7Stop1(2), data7ParityStop1(3), data8Stop1(4), data7ParityStop2(5), data8ParityStop1(6)  

mdmParity 1.3.6.1.4.1.498.4.2.1.5
Parity of the async data when the character length option selects parity.
OBJECT-TYPE    
  INTEGER even(1), space(2), odd(3), mark(4), auto(5)  

mdmOverspeed 1.3.6.1.4.1.498.4.2.1.6
Option to set DTE async overspeed data tolerated by the modem. Extended = 2.5%. Nominal = 1.25%.
OBJECT-TYPE    
  INTEGER nominal(1), extended(2)  

mdmFlowCntrl 1.3.6.1.4.1.498.4.2.1.7
Options to set the modem DTE flow control. disable Disables all flow control. xonXoffSig Enables XON/XOFF signaling between modem and DTE. cts Enables the modem to flow control the DTE via CTS. rtsCts This option operates the same as CTS option as well as allowing RTS to flow control the modem as a ready to receive signal. xonOff Allows the modem to XON/XOFF the DTE yet ignore these signals when sent by the DTE (unidirectional flow control).
OBJECT-TYPE    
  INTEGER disabled(1), xonXoffSig(2), cts(3), rtsCts(4), xonXoff(5)  

mdmTermEcho 1.3.6.1.4.1.498.4.2.1.8
Option to control the modem echo to the DTE.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

mdmDCDCntrl 1.3.6.1.4.1.498.4.2.1.9
Option the EIA DCD mode of operation. ForceOn DCD always ON. Real DCD will follow CCITT specifications. ForceOnToggleDisc DCD is On but toggle on disconnect as a signaling to the front end.
OBJECT-TYPE    
  INTEGER forceOn(1), real(2), forceOnToggleDisc(3)  

mdmCTSCntrl 1.3.6.1.4.1.498.4.2.1.10
Option the EIA CTS mode of operation. cmdOnDataRTS On during command mode, during data mode will follow RTS. cmdOnDataReal On during command mode, during data mode will follow CCITT specifications. realCCITT It follows CCITT specifications always. ForceON On all the times.
OBJECT-TYPE    
  INTEGER cmdOnDataRTS(1), cmdOnDataReal(2), realCCITT(3), forceOn(4)  

mdmDTRTrans 1.3.6.1.4.1.498.4.2.1.11
Option the modem to respond to loss of DTR. forceon Modem ignore DTR transitions. offInCmdMode Upon transition detection modem will enter command mode. offDisc Upon transition detection modem will disconnect. offDiscRecalUser Upon transition detection modem will disconect and recall the selected User configuration. This object is Country Code dependent.
OBJECT-TYPE    
  INTEGER forceon(1), offInCmdMode(2), offDisc(3), offDiscRecallUser(4)  

mdmDSRCntrl 1.3.6.1.4.1.498.4.2.1.12
Option the EIA DSR mode of operation. onUntilDisc Selects DSR to remain On and glitch Off for disconnect. Normal Causes DSR to be real. followDCD Selects DSR to follow carrier detect. forceOn Selects DSR forced On in all modes.
OBJECT-TYPE    
  INTEGER onUntilDisc(1), normal(2), followDCD(3), forceOn(4)  

mdmDSRCntrlAL 1.3.6.1.4.1.498.4.2.1.13
Option the EIA DSR operation during analoop. onAnaloop DSR will turn ON when in analoop offAnaloop DSR is forced Off when in Analoop.
OBJECT-TYPE    
  INTEGER onAnaloop(1), offAnaloop(2)  

mdmTXClockSource 1.3.6.1.4.1.498.4.2.1.14
Selects the source for TX clock generation. internal The modem uses the internally generated clock source. external The modem uses the DTE clock as a source receiverwrap The modem receiver derived timing clock to be used in the transmitter.
OBJECT-TYPE    
  INTEGER internal(1), external(2), receiverwrap(3)  

mdmRTSCTSDelay 1.3.6.1.4.1.498.4.2.1.15
Selects the delay time between RTS coming on and CTS being turned on (.001 sec).
OBJECT-TYPE    
  INTEGER 0..255  

mdmCarriageReturnCharacter 1.3.6.1.4.1.498.4.2.1.16
Select the ascii character to be used as the carriage return.
OBJECT-TYPE    
  INTEGER 0..127  

mdmCharacterAbortDialing 1.3.6.1.4.1.498.4.2.1.17
Enable/disable the option to abort dialing if a DTE character is detected.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

mdmDelayDTR 1.3.6.1.4.1.498.4.2.1.18
Selects the delay time(in Seconds) between making data mode and raising the DTR lead. It is dependent on the mode of operation. When configured for &M0 this register is used to debounce the DTR signal. The default value is five hundredths of a second (0.05second). When configured for &M1 and in data mode, this register sets the time available to the operator to switch the EIA cable from asynchronous equipment to synchronous equipment. When the timer expires, this register is used to debounce the DTR signal as in &M0 mode. The default value is five seconds.
OBJECT-TYPE    
  INTEGER 0..255  

mdmEscapeCharacter 1.3.6.1.4.1.498.4.2.1.19
Select the ascii character to be used as the 'escape to command mode' character.
OBJECT-TYPE    
  INTEGER 0..127  

mdmLineFeedCharacter 1.3.6.1.4.1.498.4.2.1.20
Select the ascii character to be used as the Line Feed character.
OBJECT-TYPE    
  INTEGER 0..127  

mdmHangUpDelay 1.3.6.1.4.1.498.4.2.1.21
Select the delay time(in Sec) between the modem detecting a command to hang up the line and the disconnect operation.
OBJECT-TYPE    
  INTEGER 0..255  

mdmEscapeCharacterGuardTime 1.3.6.1.4.1.498.4.2.1.22
This is the timer the modem will use when determining a valid escape sequence. Select the delay time(in 1/50 Sec). When a valid escape sequence is detected the modem will transfer from the data to command mode.
OBJECT-TYPE    
  INTEGER 0..255  

mdmOperatingMode 1.3.6.1.4.1.498.4.2.1.23
Option to set the type of data transfer in data mode. asyncDataMode modem operates in async mode during command or data mode. async CmdsyncData In command mode the modem uses async data. In data mode operates in synchronous mode.
OBJECT-TYPE    
  INTEGER asyncDataMode(1), asyncCmdsyncData(2)  

mdmBackSpaceCharacter 1.3.6.1.4.1.498.4.2.1.24
Select the ascii character to be used as the Back Space character.
OBJECT-TYPE    
  INTEGER 0..127  

mdmModemConfigTable 1.3.6.1.4.1.498.4.3
The GDC VFAST modem configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmModemEntry

mdmModemEntry 1.3.6.1.4.1.498.4.3.1
A listing of GDC VFAST modem options.
OBJECT-TYPE    
  MdmModemEntry  

mdmModemIndex 1.3.6.1.4.1.498.4.3.1.1
A unique index for the Modem Option Table.
OBJECT-TYPE    
  SCinstance  

mdmRingsToAns 1.3.6.1.4.1.498.4.3.1.2
Selects the number of rings received before the modem Auto Answer. This object is Country Code dependent
OBJECT-TYPE    
  INTEGER 0..255  

mdmFallFwrdBack 1.3.6.1.4.1.498.4.3.1.3
Command the modem to enable/disable rate negotiation during a retrain.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

mdmTrellis 1.3.6.1.4.1.498.4.3.1.4
Enable/disable Trellis negotiation during a handshake.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

mdmSQRetrain 1.3.6.1.4.1.498.4.3.1.5
Command to option Signal Quality Retrains.
OBJECT-TYPE    
  INTEGER disabled(1), sQThree(2), sQForever(3)  

mdmLongSpaceDisc 1.3.6.1.4.1.498.4.3.1.6
Command to enable/disable Long Space Disconnect. enable The modem will transmit 4 seconds of continuous space (BREAK) when ever a disconnect request is detected. If the modem receives more than 1.5 seconds of continuous space (BREAK) while on-line, it will hang up.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

mdmMakeBusy 1.3.6.1.4.1.498.4.3.1.7
Command to option the switched network make busy function disable Does not make busy. onLossDTR Make busy on loss of DTR. inAL Make busy during analoop. inALorLossRTSorDTR Make busy in analoop, loss of RTS or DTR. This object is Country Code dependent
OBJECT-TYPE    
  INTEGER disabled(1), onLossDTR(2), inAL(3), inALorLossRTSorDTR(4), onLossRTS(5)  

mdmRDLOptions 1.3.6.1.4.1.498.4.3.1.8
Command to enable/disable Remote Digital Loopback Instigation. disable The modem ignores the inband request to initiate a remote digital loopback. enable The modem accept the inband request to initiated a remote digital loopback.
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

mdmTestTimer 1.3.6.1.4.1.498.4.3.1.9
Command to limit any diagnostic test in 10 second intervals. When the value is zero the test runs forever.
OBJECT-TYPE    
  INTEGER 0..255  

mdmDTETestCntrl 1.3.6.1.4.1.498.4.3.1.10
Command to enable/disable diagnostic tests from DTE interface.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

mdmDCDLossDisc 1.3.6.1.4.1.498.4.3.1.11
Command to set the time (0.1sec) between loss of carrier detected and a modem disconnect. This object is Country Code dependent.
OBJECT-TYPE    
  INTEGER 0..255  

mdmCDRespTime 1.3.6.1.4.1.498.4.3.1.12
Command to set the time (in Sec) a carrier signal must be present for the modem to recognize it. This object is Country Code dependent.
OBJECT-TYPE    
  INTEGER 0..255  

mdmAnswerOriginate 1.3.6.1.4.1.498.4.3.1.13
Command to set the handshake band. answerIfRingDetect Upon detecting a ring the modem will handshake in the answer mode. forceAnswer The modem will be force to handshake in the answer mode. autoAnswerInOriginate When the modem detect a ring it will answer in the originate mode.
OBJECT-TYPE    
  INTEGER answerIfRingDetect(1), forceAnswer(2), autoAnswerInOriginate(3)  

mdmWaitForDCD 1.3.6.1.4.1.498.4.3.1.14
This object is used to store the carrier wait time. This is the time which the modem will wait after the dial has been completed until the modem senses carrier detect. It is also used for the dial command modifiers W wait for dial tone before dialing and @ wait for quiet answer before dialing. It also sets the amount of time the modem will wait for ringback when originating a call. This object is Country Code dependent.
OBJECT-TYPE    
  INTEGER 1..60  

mdmDialerConfigTable 1.3.6.1.4.1.498.4.4
The GDC VFAST dialer configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmDialerEntry

mdmDialerEntry 1.3.6.1.4.1.498.4.4.1
A listing of GDC VFAST modem dialer options.
OBJECT-TYPE    
  MdmDialerEntry  

mdmDialerIndex 1.3.6.1.4.1.498.4.4.1.1
A unique index for the Dialer Table.
OBJECT-TYPE    
  SCinstance  

mdmCPMMonitor 1.3.6.1.4.1.498.4.4.1.2
Command used to option the Call Progress Monitor operation. This object is Country Code dependent. basic The modem will blind dial and will only send a CONNECT message for all established links. All CPM is disabled. extendedNoCPM This command is the same as basic with the exception of the connect messages. The modem will send the appropiate connect response of CONNECT followed by the connected speed. extendedDialTone This command is the same as extendedNoCPM command but without blind dialing. The modem will send the NO DIALTONE message if dial tone is not detected. extendedBusy This command forces the modem to blind dial. The modem will not respond with the NO DIALTONE message while all other CPM responses are enabled. extendedFullCPM This command enables all CPM response codes and monitoring, except rinback detection. extendedFullCPMRingback This command enables all CPM response codes and monitoring, and includes ringback detection. This object is Country Code dependent.
OBJECT-TYPE    
  INTEGER basic(1), extendedNoCPM(2), extendedDialtone(3), extendedBusy(4), extendedFullCPM(5), extendedFullCPMRingback(6)  

mdmParserSelection 1.3.6.1.4.1.498.4.4.1.3
Command used to select the DTE parser. The following parsers are available: AT, v25async, v25HDLC, v25bisync, and no parser
OBJECT-TYPE    
  INTEGER at(1), v25async(2), v25HDLC(3), v25bisync(4), noparser(5)  

mdmDTRDial 1.3.6.1.4.1.498.4.4.1.4
This command sets the modem operation upon detecting an Off to On transition on DTR. disable Transition is ignored. cellNumber0 Dial number stored in cell 0. cellNumber1 Dial number stored in cell 1. cellNumber2 Dial number stored in cell 2. cellNumber3 Dial number stored in cell 3. cellNumber4 Dial number stored in cell 4. cellNumber5 Dial number stored in cell 5. cellNumber6 Dial number stored in cell 6. cellNumber7 Dial number stored in cell 7. cellNumber8 Dial number stored in cell 8. cellNumber9 Dial number stored in cell 9. talkData Starts a handshake.
OBJECT-TYPE    
  INTEGER disable(1), cellNumber0(2), cellNumber1(3), cellNumber2(4), cellNumber3(5), cellNumber4(6), cellNumber5(7), cellNumber6(8), cellNumber7(9), cellNumber8(10), cellNumber9(11), talkData(12)  

mdmDialType 1.3.6.1.4.1.498.4.4.1.5
This command selects the type of dial. Pulse or DTMF dial. This object is Country Code dependent
OBJECT-TYPE    
  INTEGER pulse(1), dtmf(2)  

mdmResponseMode 1.3.6.1.4.1.498.4.4.1.6
This Command controls when to send responses. enabled Requests the non-quiet mode, that is, to transmit result codes to the DTE as appropriate. disabled Request the quiet mode which tells the modem not to send any result codes to the DTE. enableInOriginate Disables Call Progress Monitor responses in the answer mode only. This mode is entered on detection of ring signal.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), enableInOriginate(3)  

mdmResponseType 1.3.6.1.4.1.498.4.4.1.7
This command controls the type of responses. numeric modem responses are in numeric code. alpha modem responses are in alphabetical format.
OBJECT-TYPE    
  INTEGER numeric(1), alpha(2)  

mdmPauseTime 1.3.6.1.4.1.498.4.4.1.8
This command selects the time for pause characters in the dial string. This object is Country Code dependent.
OBJECT-TYPE    
  INTEGER 0..255  

mdmWaitForDialtoneTime 1.3.6.1.4.1.498.4.4.1.9
This command selects the time for the modem to be looking for dialtone before disconnecting. This object is Country Code dependent
OBJECT-TYPE    
  INTEGER 0..255  

mdmProtocolConfigTable 1.3.6.1.4.1.498.4.5
The GDC VFAST modem Protocol configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmProtocolEntry

mdmProtocolEntry 1.3.6.1.4.1.498.4.5.1
A listing of GDC VFAST modem Protocol options.
OBJECT-TYPE    
  MdmProtocolEntry  

mdmProtocolIndex 1.3.6.1.4.1.498.4.5.1.1
A unique index for the DTE Table.
OBJECT-TYPE    
  SCinstance  

mdmCompression 1.3.6.1.4.1.498.4.5.1.2
This command controls the Compression operation when operating in asynchronous mode. disabled No compression available. enabled Compression available in both directions. txpathonly Compression available in the transmitter path only when in V.42bis. In MNP 5 data compression is enabled in both directions. rxpathonly Compression available in the receiver path only when in V.42bis. In MNP 5 data compression is enabled in both directions.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2), txpathonly(3), rxpathonly(4)  

mdmAsyncProtocol 1.3.6.1.4.1.498.4.5.1.3
This command controls the Protocols available at the handshake. wire Options the modem to run in wire mode; copying characters from VF port to the DTE port and vice versa. direct Options the modem to run in direct mode; where the DTE and the VF speeds must match, and there is no speed buffering. Direct mode is V.14 asynchronous mode. mnpreliable This option limits error correction to MNP links only or hang up. autoreliable Options the mode to run in autoreliable mode, and the modem will negotiate V.42 or alternate links. With no link, the modem will enter wire mode (speed buffering). v42reliable This option limits error correction to a V.42 (LAPM) link or hang up. reliableLAPMorMNP This option will attempt either a V.42 (LAPM) or MNP link and if either link fails, the modem will hang up. V.13 This option selects V.13 simulated controlled carrier.
OBJECT-TYPE    
  INTEGER wire(1), direct(2), mnpreliable(3), autoreliable(4), v42reliable(5), reliableLAPMorMNP(6), v13(7)  

mdmFlowControl 1.3.6.1.4.1.498.4.5.1.4
This command controls the flow control type between the modem and the DTE available at the handshake. disabled Disables modem to modem flow control. enabled Enables bidirectional modem flow control based on XON/XOFF signaling. These signals are detected, acted on and optionally deleted from the data stream. Unidirectional provides unidirectional flow control where a modem may send XON/XOFF signals to the remote modem, yet ignore and pass through any these VF received signals to its DTE. bidirectional Acts the same as enabled with the addition of the XON/XOFF pass through option being enabled.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2), unidirectional(3), bidirectional(4)  

mdmBreakHandling 1.3.6.1.4.1.498.4.5.1.5
This command controls the operation of breaks. expediteDest This option will immediately transmit a break character for a fix time (300 msec) and destroy any currently bufered data. expediteNonDest This option is the same as expediteDest except all buffered data will be save. nonExpediteNonDest This option will transmit a fixed time break character in sequence with the rest of the data. ignore Ignores all break received from the DTE. timedNonExoediteNonDest This option transmits break characters in sequence with the rest of the data for the duration the DTE is transmitting this character. timedNonExpediteNonDest2 Same as above.
OBJECT-TYPE    
  INTEGER expediteDest(1), expediteNonDest(2), nonExpediteNonDest(3), ignored(4), timedNonExpediteNonDest(5), timedNonExpediteNonDest2(6)  

mdmConnAndLinkMessages 1.3.6.1.4.1.498.4.5.1.6
This command controls when to send the protocol messages. separateMessages This options the modem to send the standard GDC conect message upon reaching data mode plus V.42 message after the link negotiation. The connect message displays VF line speed. bothAfterLink With this option the connect and link messages are send after link negotiation. microcomCompatible This option is the same as bothAfterLink except adds a /RELIABLE at the end of the message when a V.42 error corrected link has been establish. connectAfterLink This option sends only the connect message after the link negotiation. The message will indicate the VF rate for V.13 and V.14 connections and the DTE rate for all other connections.
OBJECT-TYPE    
  INTEGER separateMessages(1), bothAfterLink(2), microcomCompatible(3), connectAfterLink(4)  

mdmErrorCorrection 1.3.6.1.4.1.498.4.5.1.7
This command controls how the data is handled when running a protocol. noBuffer This option discards all data coming in from the modem until the receiver modem sends a PROTOCOL: NONE message to the DTE at which time data will be passed through. bufferRxData This option will buffer received data (up to 200 characters) until the PROTOCOL: NONE message is sent. The buffered data will be passed through to the DTE. The modem will fall back to wire mode if more than 200 characters have been received prior to establishing an error correction link. fallbackWithFallbackChar This command discards all incoming data until two consecutive fallback characters are detected at which point the receiver modem falls back to wire mode. One fallback character is passed through to its DTE as data. fallbackV14Buffer This option acts the same as bufferRxData except with no link it falls back to V.14 (direct)mode. fallbackV14WithFallbackChar This option acts as fallbackWithFallbackChar except it also falls back to V.14 (direct) mode.
OBJECT-TYPE    
  INTEGER noBuffer(1), bufferRxData(2), fallbackWithFallbackChar(3), fallbackV14Buffer(4), fallbackV14WithFallbackChar(5)  

mdmV13Mode 1.3.6.1.4.1.498.4.5.1.8
This command controls the V13 function. bidirectional Selects bidirectional V.13 simulated controlled carrier. txEnable Selects V.13 Tx side enabled. rxEnable Selects V.13 RX side enabled.
OBJECT-TYPE    
  INTEGER bidirectional(1), txEnable(2), rxEnable(3)  

mdmSyncProtocol 1.3.6.1.4.1.498.4.5.1.9
This command controls the type of sync protocol. normalsync Selects normal synchronous mode. v13sync Selects synchronous V13 mode.
OBJECT-TYPE    
  INTEGER normalsync(1), v13sync(2)  

mdmFrameRetransLimit 1.3.6.1.4.1.498.4.5.1.10
This command limits the number of times the modem will retransmit a frame while in an error correction connection.
OBJECT-TYPE    
  INTEGER 0..255  

mdmPrivateLineConfigTable 1.3.6.1.4.1.498.4.6
The GDC VFAST modem Private Line configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmPrivateLineEntry

mdmPrivateLineEntry 1.3.6.1.4.1.498.4.6.1
A listing of GDC VFAST Private Line configurations options.
OBJECT-TYPE    
  MdmPrivateLineEntry  

mdmPrivateLineIndex 1.3.6.1.4.1.498.4.6.1.1
A unique index for the Private Line Configurations Table.
OBJECT-TYPE    
  SCinstance  

mdmPrivateLineTxLevel 1.3.6.1.4.1.498.4.6.1.2
This command selects the transmit level during Private Line operation. This object is Country Code dependent
OBJECT-TYPE    
  INTEGER dBm0(1), dBm1(2), dBm2(3), dBm3(4), dBm4(5), dBm5(6), dBm6(7), dBm7(8), dBm8(9), dBm9(10), dBm10(11), dBm11(12), dBm12(13), dBm13(14), dBm14(15), dBm15(16)  

mdmPrivateLineHandshakeMode 1.3.6.1.4.1.498.4.6.1.3
This command selects the Private Line Handshake modes
OBJECT-TYPE    
  INTEGER gdcVfastonly(1), v32bisonly(2), v32only(3)  

mdmAutoDialRestoral 1.3.6.1.4.1.498.4.6.1.4
This command selects the options for Auto Dial Restoral when the modem is in private line mode. disabled No Auto Dial Restoral allowed. enableWithEndOfSession Enable Auto Dial Restoral with line failure indicator. enableWithoutEnOfSession Enable Auto Dial Restoral without line failure indicator.
OBJECT-TYPE    
  INTEGER disabled(1), enableWithEndOfSession(2), enableWithoutEndOfSession(3)  

mdmPrivateLineDownTime 1.3.6.1.4.1.498.4.6.1.5
This command selects for how long the Private Line must be lost before going to Dial Back Up mode
OBJECT-TYPE    
  INTEGER 0..255  

mdmDBUtoPLLookbackTime 1.3.6.1.4.1.498.4.6.1.6
This command selects the time for how often the modem must lookback for Private Line restoral. The units are in 10 minutes. Valid range from 0 to 255. When the value 0 is selected this option is disabled.
OBJECT-TYPE    
  INTEGER 0..255  

mdmAlarmScanTable 1.3.6.1.4.1.498.4.7
The GDC VFAST alarm Scan Table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmAlarmScanEntry

mdmAlarmScanEntry 1.3.6.1.4.1.498.4.7.1
An entry in the GDC VFAST alarm table.
OBJECT-TYPE    
  MdmAlarmScanEntry  

mdmAlarmScanIndex 1.3.6.1.4.1.498.4.7.1.1
This object is the identifier of the VFAST alarm table.
OBJECT-TYPE    
  SCinstance  

mdmAlarmScan 1.3.6.1.4.1.498.4.7.1.2
Reads the alarm scan. There are 8 bytes. byte 1 bit 4 (bit 1.4) No DTR signal bit 2.0 No TXD Transitions bit 2.2 No RXD Transitions bit 2.3 Modem Fallback bit 2.6 Modem on Dial Back Up bit 3.2 Power Up bit 4.0 Poor Signal Quality bit 5.3 DCD Loss bit 6.0-6 no alarms bit 7.0 Modem Configuration Checksum Error bit 7.1 Call Failed bit 7.2 Call Length Exceeded Maximum Allowed bit 7.3 Retrain Count Exceeded Threshold bit 7.4 Ring No Answer bit 7.5 Remote Configuration session active bit 7.6 Test timeout bit 8.0-6 no alarms
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

mdmResetSelfPowerBit 1.3.6.1.4.1.498.4.7.1.3
This resets the modem power up alarm.
OBJECT-TYPE    
  INTEGER reset(1)  

mdmMaskAlarmTable 1.3.6.1.4.1.498.4.8
The GDC VFAST alarm Mask Table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmMaskAlarmEntry

mdmMaskAlarmEntry 1.3.6.1.4.1.498.4.8.1
An entry in the GDC VFAST alarm mask table.
OBJECT-TYPE    
  MdmMaskAlarmEntry  

mdmMaskAlarmIndex 1.3.6.1.4.1.498.4.8.1.1
This object is the index of the VFAST alarm mask table.
OBJECT-TYPE    
  SCinstance  

mdmDTRLoss 1.3.6.1.4.1.498.4.8.1.2
Mask for loss of DTR alarm.
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmFallback 1.3.6.1.4.1.498.4.8.1.3
Mask for fallback alarm.
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmRxdTran 1.3.6.1.4.1.498.4.8.1.4
Mask for Receive data transitions alarm.
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmTxdTran 1.3.6.1.4.1.498.4.8.1.5
Mask for transmit data transitions alarm.
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmDCDLoss 1.3.6.1.4.1.498.4.8.1.6
Mask for loss of DCD alarm.
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmRingNoAnswer 1.3.6.1.4.1.498.4.8.1.7
Mask for Rings no Answer alarm.
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmRetrain 1.3.6.1.4.1.498.4.8.1.8
Mask for Retrains count exceeded alarm.
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmCallLength 1.3.6.1.4.1.498.4.8.1.9
Mask for Call Length exceeded alarm.
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmCallFail 1.3.6.1.4.1.498.4.8.1.10
Mask for Call Failed alarm.
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmConfigErr 1.3.6.1.4.1.498.4.8.1.11
Mask for Configuration checksum error alarm.
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmSignalQuality 1.3.6.1.4.1.498.4.8.1.12
Mask for Poor Signal Quality alarm.
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmOnDBU 1.3.6.1.4.1.498.4.8.1.13
Mask for On Dial Backup alarm.
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmRemoteConfigMask 1.3.6.1.4.1.498.4.8.1.14
Mask for Remote Configuration.
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmTestTimeout 1.3.6.1.4.1.498.4.8.1.15
Mask for Test timeout.
OBJECT-TYPE    
  INTEGER mask(1), unmask(2)  

mdmThresholdsTable 1.3.6.1.4.1.498.4.9
The GDC VFAST Alarm Thresholds Table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmThresholdsEntry

mdmThresholdsEntry 1.3.6.1.4.1.498.4.9.1
An entry in the GDC VFAST Alarm Thresholds table.
OBJECT-TYPE    
  MdmThresholdsEntry  

mdmThresholdsIndex 1.3.6.1.4.1.498.4.9.1.1
This object is the identifier of the Thresholds table.
OBJECT-TYPE    
  SCinstance  

mdmCallDuration 1.3.6.1.4.1.498.4.9.1.2
This option selects the call duration threshold for alarm.
OBJECT-TYPE    
  TimeTicks  

mdmRetrainThreshold 1.3.6.1.4.1.498.4.9.1.3
This option selects the number of retrains threshold for alarm.
OBJECT-TYPE    
  INTEGER 0..65535  

mdmStatusTable 1.3.6.1.4.1.498.4.10
The GDC VFAST Status Table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmStatusEntry

mdmStatusEntry 1.3.6.1.4.1.498.4.10.1
An entry in the GDC VFAST Status table.
OBJECT-TYPE    
  MdmStatusEntry  

mdmStatusIndex 1.3.6.1.4.1.498.4.10.1.1
This object is the identifier of the VFAST Status table.
OBJECT-TYPE    
  SCinstance  

mdmPLLookbackStatus 1.3.6.1.4.1.498.4.10.1.2
Shows the status of Private Line lookback.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

mdmAutoDialRestoralStatus 1.3.6.1.4.1.498.4.10.1.3
Shows the status of Auto Dial Restoral.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

mdmTXDtransitions 1.3.6.1.4.1.498.4.10.1.4
EIA Status of TXD data transitions.
OBJECT-TYPE    
  INTEGER notransition(1), transition(2)  

mdmRXDtransitions 1.3.6.1.4.1.498.4.10.1.5
EIA Status of RXD data transitions.
OBJECT-TYPE    
  INTEGER notransition(1), transition(2)  

mdmRTStransitions 1.3.6.1.4.1.498.4.10.1.6
EIA Status of Request to Send transitions.
OBJECT-TYPE    
  INTEGER notransition(1), transition(2)  

mdmDTRtransitions 1.3.6.1.4.1.498.4.10.1.7
EIA Status of Data Terminal Ready transitions.
OBJECT-TYPE    
  INTEGER notransition(1), transition(2)  

mdmDCDtransitions 1.3.6.1.4.1.498.4.10.1.8
EIA Status of Carrier Detect transitions.
OBJECT-TYPE    
  INTEGER notransition(1), transition(2)  

mdmTXCLKtransitions 1.3.6.1.4.1.498.4.10.1.9
EIA Status Transmit Clock transitions.
OBJECT-TYPE    
  INTEGER notransition(1), transition(2)  

mdmDTR 1.3.6.1.4.1.498.4.10.1.10
EIA Status of Data Terminal Ready.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mdmCTS 1.3.6.1.4.1.498.4.10.1.11
EIA Status of Clear to Send.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mdmDSR 1.3.6.1.4.1.498.4.10.1.12
EIA Status of Data Set Ready.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mdmDCD 1.3.6.1.4.1.498.4.10.1.13
EIA Status of Carrier Detect.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mdmSQM 1.3.6.1.4.1.498.4.10.1.14
EIA Status of Signal Quality.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mdmRTS 1.3.6.1.4.1.498.4.10.1.15
EIA Status of Request to Send.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mdmSwitchedPrivate 1.3.6.1.4.1.498.4.10.1.16
Switched Network or Private Line configuration setting.
OBJECT-TYPE    
  INTEGER switchedNetwork(1), privateLine(2)  

mdmControlTable 1.3.6.1.4.1.498.4.11
The GDC VFAST Control Table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmControlEntry

mdmControlEntry 1.3.6.1.4.1.498.4.11.1
An entry in the GDC VFAST Control table.
OBJECT-TYPE    
  MdmControlEntry  

mdmControlIndex 1.3.6.1.4.1.498.4.11.1.1
This object is the identifier of the VFAST Control table.
OBJECT-TYPE    
  SCinstance  

mdmSoftReset 1.3.6.1.4.1.498.4.11.1.2
Forces a soft reset on the modem. Not applicable when the modem is in Remote Configuration session.
OBJECT-TYPE    
  INTEGER reset(1)  

mdmFrontPanel 1.3.6.1.4.1.498.4.11.1.3
This command controls the functionality of the front panel Switches.
OBJECT-TYPE    
  INTEGER inhibit(1), enabled(2)  

mdmMakeClearBusy 1.3.6.1.4.1.498.4.11.1.4
Command used to control the Offhook relay to make busy or clear the VF line. Not applicable when the modem is in Remote Configuration session.
OBJECT-TYPE    
  INTEGER onHook(1), offHook(2)  

mdmPLTalkData 1.3.6.1.4.1.498.4.11.1.5
Object is used to force the modem to the idle or data state while configured for Private line. Idle, allows the modem to activate the private line option. Data, forces the modem to retrain.
OBJECT-TYPE    
  INTEGER idle(1), data(2)  

mdmWhatAreYouTable 1.3.6.1.4.1.498.4.12
The GDC VFAST What Are You Table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmWhatAreYouEntry

mdmWhatAreYouEntry 1.3.6.1.4.1.498.4.12.1
An entry in the GDC VFAST What Are You table.
OBJECT-TYPE    
  MdmWhatAreYouEntry  

mdmWhatAreYouIndex 1.3.6.1.4.1.498.4.12.1.1
This object is the identifier of the VFAST What Are You table.
OBJECT-TYPE    
  SCinstance  

mdmVFCard 1.3.6.1.4.1.498.4.12.1.2
This function returns the value the VF card attached to the modem.
OBJECT-TYPE    
  INTEGER domestic(1), cardA(65), cardB(66), cardC(67), cardD(68), cardE(69), cardF(70), cardG(71), cardH(72), cardJ(74), cardK(75), cardL(76), cardM(77), cardN(78), cardP(80), cardR(82), noCard(127)  

mdmDTECard 1.3.6.1.4.1.498.4.12.1.3
This function returns the type of DTE card attached to the modem.
OBJECT-TYPE    
  INTEGER v35(1), eia530(2), eia232(3)  

mdmProductCode 1.3.6.1.4.1.498.4.12.1.4
This identifies what type of device this is.
OBJECT-TYPE    
  INTEGER dmsVfast(23)  

mdmCodeRev 1.3.6.1.4.1.498.4.12.1.5
This function returns the firmware code level. example 01 - A- 02 - B-
OBJECT-TYPE    
  DisplayString SIZE(2)  

mdmBootRev 1.3.6.1.4.1.498.4.12.1.6
This function returns the boot firmware level. example 01 - A- 02 - B-
OBJECT-TYPE    
  DisplayString SIZE(2)  

mdmCountryCode 1.3.6.1.4.1.498.4.12.1.7
This function returns the country code number in three bytes. Each byte is the hex value of an decimal number. Example hex 30,30,31 is the country code of USA 001 30,34,34 is the country code of UK 044
OBJECT-TYPE    
  DisplayString SIZE(3)  

mdmDiagnosticTable 1.3.6.1.4.1.498.4.13
The GDC VFAST diagnostics table. Not applicable when the modem is in Remote Configuration session.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmDiagnosticEntry

mdmDiagnosticEntry 1.3.6.1.4.1.498.4.13.1
A listing of GDC VFAST diagnostic tests
OBJECT-TYPE    
  MdmDiagnosticEntry  

mdmDiagnosticIndex 1.3.6.1.4.1.498.4.13.1.1
A unique index for the Diagnostic Table.
OBJECT-TYPE    
  SCinstance  

mdmDiagnosticTest 1.3.6.1.4.1.498.4.13.1.2
This function selects the test. Not applicable when the modem is in Remote Configuration session.
OBJECT-TYPE    
  INTEGER terminateTest(1), analoop(2), analoopSelfTest(3), remoteDigitalLoop(4), remoteDigitalLoopSelfTest(5), selfTest(6), digitalLoop(7)  

mdmDiagnosticResults 1.3.6.1.4.1.498.4.13.1.3
This function reads the test results in bit errors.
OBJECT-TYPE    
  INTEGER 0..65535  

mdmDiagnosticStatus 1.3.6.1.4.1.498.4.13.1.4
Diagnostic status of which test is running. Not applicable when the modem is in Remote Configuration session.
OBJECT-TYPE    
  INTEGER rmtDigLpHsk(1), inboundRmtDigLp(2), rmtDigLp(4), localDigLp(8), analoopHsk(16), analoop(32), selftest(64), rmtDigLpSelftest(68), analoopSelftest(96), notInTest(97)  

mdmTestStatus 1.3.6.1.4.1.498.4.13.1.5
Test Status canNotBeDone - means test can not be done at this time terminated - means the test was terminated, could be terminated via the front panel timedout - the modem's test timer expired noPrevStatus - means that no status is currently available Not applicable when the modem is in Remote Configuration session.
OBJECT-TYPE    
  INTEGER canNotBeDone(4), terminated(8), timedout(16), noPrevStatus(17)  

mdmTestDuration 1.3.6.1.4.1.498.4.13.1.6
Time of modem in test, counted in timeticks. Not applicable when the modem is in Remote Configuration session.
OBJECT-TYPE    
  TimeTicks  

mdmDialingFunctionTable 1.3.6.1.4.1.498.4.14
The GDC VFAST modem dialing function table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmDialingFunctionEntry

mdmDialingFunctionEntry 1.3.6.1.4.1.498.4.14.1
A listing of GDC VFAST modem dialing function parameters.
OBJECT-TYPE    
  MdmDialingFunctionEntry  

mdmDialFunctionIndex 1.3.6.1.4.1.498.4.14.1.1
A unique index for the Dialing Function Table.
OBJECT-TYPE    
  SCinstance  

mdmManualDial 1.3.6.1.4.1.498.4.14.1.2
Command to instruct the modem to dial the following number, n. Not applicable when modem in remote configuration session.
OBJECT-TYPE    
  DisplayString SIZE(1..36)  

mdmTerminateCall 1.3.6.1.4.1.498.4.14.1.3
Command to instruct the mode to disconnect the call and go to idle.
OBJECT-TYPE    
  INTEGER goOnhook(1)  

mdmDialStatus 1.3.6.1.4.1.498.4.14.1.4
Dial Status information 'inTest' means the modem is currently in a test mode.
OBJECT-TYPE    
  INTEGER disconnect(1), idle(2), dial(4), training(8), retrain(16), data(32), inTest(33)  

mdmCallProgressStatus 1.3.6.1.4.1.498.4.14.1.5
Call Progress Status
OBJECT-TYPE    
  INTEGER ringback(1), incomingRing(2), busy(4), noAnswer(8), ringAndNoAnswer(10), noCarrier(16), ringbackNoCarrier(17), ringNoCarrier(18), ringNoCarrier2(19), noDialtone(32), noLoopCurrent(64), unobtainableNumber(128), connect(256), connectRingback(257), connectIncomingRing(258), connectIncomingRing2(259), noPrevStatus(260)  

mdmDialingCellsFunctionTable 1.3.6.1.4.1.498.4.15
The GDC VFAST modem dialing cells function table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmDialingCellsFunctionEntry

mdmDialingCellsFunctionEntry 1.3.6.1.4.1.498.4.15.1
A listing of GDC VFAST modem dialing cells function parameters.
OBJECT-TYPE    
  MdmDialingCellsFunctionEntry  

mdmDialCellFunctionIndex 1.3.6.1.4.1.498.4.15.1.1
A unique index for the Dialing Function Table. Not applicable when modem in remote configuration session.
OBJECT-TYPE    
  SCinstance  

mdmCellNumber 1.3.6.1.4.1.498.4.15.1.2
Command to instruct the modem to attempt dialing the phone number stored in Cell n. Not applicable when modem in remote configuration session.
OBJECT-TYPE    
  INTEGER  

mdmDial 1.3.6.1.4.1.498.4.15.1.3
Command modem to dial. Not applicable when modem in remote configuration session.
OBJECT-TYPE    
  INTEGER goDial(1)  

mdmCellPhoneNumber 1.3.6.1.4.1.498.4.15.1.4
Command to cause the modem to display the phone number stored in any of the 10 dial cell locations (0-9).
OBJECT-TYPE    
  DisplayString SIZE(1..36)  

mdmTerminateCellCall 1.3.6.1.4.1.498.4.15.1.5
Command to instruct the mode to disconnect the call and go to idle.
OBJECT-TYPE    
  INTEGER goOnhook(1)  

mdmMaintenanceTable 1.3.6.1.4.1.498.4.16
The GDC VFAST Maintenance Table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmMaintenanceEntry

mdmMaintenanceEntry 1.3.6.1.4.1.498.4.16.1
An entry in the GDC VFAST Maintenance table.
OBJECT-TYPE    
  MdmMaintenanceEntry  

mdmMaintenanceIndex 1.3.6.1.4.1.498.4.16.1.1
A unique index for the Maintenance Index Table.
OBJECT-TYPE    
  SCinstance  

mdmSaveRecallConfig 1.3.6.1.4.1.498.4.16.1.2
This command allows the user to load or save factory or user profile configurations into the modem.
OBJECT-TYPE    
  INTEGER recallFactoryDefault0(1), recallFactoryDefault1(2), recallFactoryDefault2(3), recallFactoryDefault3(4), recallUserProfile0(5), recallUserProfile1(6), recallUserProfile2(7), recallUserProfile3(8), saveUserProfile0(9), saveUserProfile1(10), saveUserProfile2(11), saveUserProfile3(12)  

mdmConfigCksum 1.3.6.1.4.1.498.4.16.1.3
Reads the configuration checksum of the modem.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

mdmPassword 1.3.6.1.4.1.498.4.16.1.4
This function sets the modem password. The maximum number of digits in the password must be equal or less than 10. If no password is entered the password is non-functional.
OBJECT-TYPE    
  DisplayString SIZE(0..10)  

mdmSerialNumber 1.3.6.1.4.1.498.4.16.1.5
Network element serial number
OBJECT-TYPE    
  DisplayString SIZE(16)  

mdmPowerUpProfile 1.3.6.1.4.1.498.4.16.1.6
Command to select 1 of 4 custom modem configurations at power up.
OBJECT-TYPE    
  INTEGER zero(1), one(2), two(3), three(4)  

mdmPasswordOperation 1.3.6.1.4.1.498.4.16.1.7
This object identifies the Password Operation. The GDC proprietary handshake password validation operation and the on line (entered by the remote user) password validation operation can be enabled or disabled globally or selectively. disabled - password operations disabled enablehandshake - enable the handshake password operation enableonline - enable the answering modem to locally validate the remote user entered password enable - enable both handshake and online password operations Not applicable when the modem is in Remote Configuration session.
OBJECT-TYPE    
  INTEGER disabled(1), enablehandshake(2), enableonline(3), enable(4)  

mdmStatisticsTable 1.3.6.1.4.1.498.4.17
The GDC VFAST Statistics Table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmStatisticsEntry

mdmStatisticsEntry 1.3.6.1.4.1.498.4.17.1
An entry in the GDC VFAST Statistics table.
OBJECT-TYPE    
  MdmStatisticsEntry  

mdmStatisticsIndex 1.3.6.1.4.1.498.4.17.1.1
This object is the identifier of the VFAST Statistics table.
OBJECT-TYPE    
  SCinstance  

mdmDCERate 1.3.6.1.4.1.498.4.17.1.2
This object identifies the DCE speed that the modem is operating.
OBJECT-TYPE    
  INTEGER bps300(2), bps1200(3), bps2400(4), bps4800(5), bps7200(6), bps9600(7), bps12000(8), bps14400(9), bps16800(10), bps19200(11), bps21600(12), bps24000(13), bps26400(14), bps28800(15)  

mdmCallDurationStat 1.3.6.1.4.1.498.4.17.1.3
This function reads the duration of the last or current Switched Network connection in timeticks.
OBJECT-TYPE    
  TimeTicks  

mdmRetrainCount 1.3.6.1.4.1.498.4.17.1.4
This function reads the number of retrains.
OBJECT-TYPE    
  INTEGER 0..127  

mdmFallbackCount 1.3.6.1.4.1.498.4.17.1.5
This function reads the number of times that the modem falls back.
OBJECT-TYPE    
  INTEGER 0..127  

mdmFallforwardCount 1.3.6.1.4.1.498.4.17.1.6
This function reads the number of times that the modem falls forward.
OBJECT-TYPE    
  INTEGER 0..127  

mdmRxSignalLevel 1.3.6.1.4.1.498.4.17.1.7
This function reads the input signal level in dB.
OBJECT-TYPE    
  INTEGER 0..127  

mdmSignaltoNoiseRatio 1.3.6.1.4.1.498.4.17.1.8
This function reads the signal to noise ratio in dB.
OBJECT-TYPE    
  INTEGER 0..127  

mdmAnswerOriginateStat 1.3.6.1.4.1.498.4.17.1.9
This function reads the band that the modem is operating in data mode.
OBJECT-TYPE    
  INTEGER originate(1), answer(2)  

mdmDiscReason 1.3.6.1.4.1.498.4.17.1.10
This function reads the reason why the modem has disconnected. usertimeout - user timed out while entering prompted information.
OBJECT-TYPE    
  INTEGER usertimeout(1), unknown(2)  

mdmCompressionEfficiency 1.3.6.1.4.1.498.4.17.1.11
The number of bytes transferred into the compression encoder divided by the number of bytes transferred out of the encoder, multiplied by 100 for either the current or last call. If a data compression protocol is not in use, this value shall be '100'.
OBJECT-TYPE    
  INTEGER 0..65535  

mdmThruput 1.3.6.1.4.1.498.4.17.1.12
The data thruput rate is the number of bytes received from the DCE and then sent to the DTE per second.
OBJECT-TYPE    
  INTEGER 0..65535  

mdmRemoteConfigTable 1.3.6.1.4.1.498.4.18
The GDC VFAST Remote Configuration Table.
OBJECT-TYPE    
  SEQUENCE OF  
    MdmRemoteConfigEntry

mdmRemoteConfigEntry 1.3.6.1.4.1.498.4.18.1
An entry in the GDC VFAST Remote Config table.
OBJECT-TYPE    
  MdmRemoteConfigEntry  

mdmRemoteConfigIndex 1.3.6.1.4.1.498.4.18.1.1
This object is the identifier of the VFAST Remote Configuration table.
OBJECT-TYPE    
  SCinstance  

mdmRemoteConfiguration 1.3.6.1.4.1.498.4.18.1.2
This object options the Remote configuration for the local unit before dial.
OBJECT-TYPE    
  INTEGER disable(1), enableDTE(2), enableDMS(3)  

mdmEndRemoteConfiguration 1.3.6.1.4.1.498.4.18.1.3
This option tells the far end unit to disconnect and update the options or not that have been changed during the remote configuration session.
OBJECT-TYPE    
  INTEGER noUpdate(1), update(2)  

mdmPasswordRemoteConfiguration 1.3.6.1.4.1.498.4.18.1.4
This option stores the Remote Configuration Password. When a password is stored in the answer modem it must be matched during the handshake by the originating modem. If the password matching fails, the answer modem will drop the connection. Not applicable when the modem is in Remote Configuration session.
OBJECT-TYPE    
  DisplayString SIZE(0..10)  

mdmMIBVersion 1.3.6.1.4.1.498.4.19
The version number of the MIB, to allow products to know which MIB is being supported. The version number will be x.yzT where x is a major revision (1-9), y is a minor revision(0-9), z is a typo revision (0-9) and T indicates the MIB is still a test revision(A-Z). When a release is complete no T should exist.
OBJECT-TYPE    
  DisplayString SIZE(5)  

Defined Objects

MdmNetworkEntry  
SEQUENCE    
  SCinstance as mdmNetworkIndex  
  INTEGER as mdmNetworkType  
  INTEGER as mdmSNTxType  
  INTEGER as mdmSNTxLevel  
  INTEGER as mdmSNHandshakeMode  

MdmDTEntry  
SEQUENCE    
  SCinstance as mdmDTEIndex  
  INTEGER as mdmDTESpeed  
  INTEGER as mdmCPMResp  
  INTEGER as mdmCharLength  
  INTEGER as mdmParity  
  INTEGER as mdmOverspeed  
  INTEGER as mdmFlowCntrl  
  INTEGER as mdmTermEcho  
  INTEGER as mdmDCDCntrl  
  INTEGER as mdmCTSCntrl  
  INTEGER as mdmDTRTrans  
  INTEGER as mdmDSRCntrl  
  INTEGER as mdmDSRCntrlAL  
  INTEGER as mdmTXClockSource  
  INTEGER as mdmRTSCTSDelay  
  INTEGER as mdmCarriageReturnCharacter  
  INTEGER as mdmCharacterAbortDialing  
  INTEGER as mdmDelayDTR  
  INTEGER as mdmEscapeCharacter  
  INTEGER as mdmLineFeedCharacter  
  INTEGER as mdmHangUpDelay  
  INTEGER as mdmEscapeCharacterGuardTime  
  INTEGER as mdmOperatingMode  
  INTEGER as mdmBackSpaceCharacter  

MdmModemEntry  
SEQUENCE    
  SCinstance as mdmModemIndex  
  INTEGER as mdmRingsToAns  
  INTEGER as mdmFallFwrdBack  
  INTEGER as mdmTrellis  
  INTEGER as mdmSQRetrain  
  INTEGER as mdmLongSpaceDisc  
  INTEGER as mdmMakeBusy  
  INTEGER as mdmRDLOptions  
  INTEGER as mdmTestTimer  
  INTEGER as mdmDTETestCntrl  
  INTEGER as mdmDCDLossDisc  
  INTEGER as mdmCDRespTime  
  INTEGER as mdmAnswerOriginate  
  INTEGER as mdmWaitForDCD  

MdmDialerEntry  
SEQUENCE    
  SCinstance as mdmDialerIndex  
  INTEGER as mdmCPMMonitor  
  INTEGER as mdmParserSelection  
  INTEGER as mdmDTRDial  
  INTEGER as mdmDialType  
  INTEGER as mdmResponseMode  
  INTEGER as mdmResponseType  
  INTEGER as mdmPauseTime  
  INTEGER as mdmWaitForDialtoneTime  

MdmProtocolEntry  
SEQUENCE    
  SCinstance as mdmProtocolIndex  
  INTEGER as mdmCompression  
  INTEGER as mdmAsyncProtocol  
  INTEGER as mdmFlowControl  
  INTEGER as mdmBreakHandling  
  INTEGER as mdmConnAndLinkMessages  
  INTEGER as mdmErrorCorrection  
  INTEGER as mdmV13Mode  
  INTEGER as mdmSyncProtocol  
  INTEGER as mdmFrameRetransLimit  

MdmPrivateLineEntry  
SEQUENCE    
  SCinstance as mdmPrivateLineIndex  
  INTEGER as mdmPrivateLineTxLevel  
  INTEGER as mdmPrivateLineHandshakeMode  
  INTEGER as mdmAutoDialRestoral  
  INTEGER as mdmPrivateLineDownTime  
  INTEGER as mdmDBUtoPLLookbackTime  

MdmAlarmScanEntry  
SEQUENCE    
  SCinstance as mdmAlarmScanIndex  
  OCTET STRING as mdmAlarmScan  
  INTEGER as mdmResetSelfPowerBit  

MdmMaskAlarmEntry  
SEQUENCE    
  SCinstance as mdmMaskAlarmIndex  
  INTEGER as mdmDTRLoss  
  INTEGER as mdmFallback  
  INTEGER as mdmRxdTran  
  INTEGER as mdmTxdTran  
  INTEGER as mdmDCDLoss  
  INTEGER as mdmRingNoAnswer  
  INTEGER as mdmRetrain  
  INTEGER as mdmCallLength  
  INTEGER as mdmCallFail  
  INTEGER as mdmConfigErr  
  INTEGER as mdmSignalQuality  
  INTEGER as mdmOnDBU  
  INTEGER as mdmRemoteConfigMask  
  INTEGER as mdmTestTimeout  

MdmThresholdsEntry  
SEQUENCE    
  SCinstance as mdmThresholdsIndex  
  TimeTicks as mdmCallDuration  
  INTEGER as mdmRetrainThreshold  

MdmStatusEntry  
SEQUENCE    
  SCinstance as mdmStatusIndex  
  INTEGER as mdmPLLookbackStatus  
  INTEGER as mdmAutoDialRestoralStatus  
  INTEGER as mdmTXDtransitions  
  INTEGER as mdmRXDtransitions  
  INTEGER as mdmRTStransitions  
  INTEGER as mdmDTRtransitions  
  INTEGER as mdmDCDtransitions  
  INTEGER as mdmTXCLKtransitions  
  INTEGER as mdmDTR  
  INTEGER as mdmCTS  
  INTEGER as mdmDSR  
  INTEGER as mdmDCD  
  INTEGER as mdmSQM  
  INTEGER as mdmRTS  
  INTEGER as mdmSwitchedPrivate  

MdmControlEntry  
SEQUENCE    
  SCinstance as mdmControlIndex  
  INTEGER as mdmSoftReset  
  INTEGER as mdmFrontPanel  
  INTEGER as mdmMakeClearBusy  
  INTEGER as mdmPLTalkData  

MdmWhatAreYouEntry  
SEQUENCE    
  SCinstance as mdmWhatAreYouIndex  
  INTEGER as mdmVFCard  
  INTEGER as mdmDTECard  
  INTEGER as mdmProductCode  
  DisplayString as mdmCodeRev  
  DisplayString as mdmBootRev  
  DisplayString as mdmCountryCode  

MdmDiagnosticEntry  
SEQUENCE    
  SCinstance as mdmDiagnosticIndex  
  INTEGER as mdmDiagnosticTest  
  INTEGER as mdmDiagnosticResults  
  INTEGER as mdmDiagnosticStatus  
  INTEGER as mdmTestStatus  
  TimeTicks as mdmTestDuration  

MdmDialingFunctionEntry  
SEQUENCE    
  SCinstance as mdmDialFunctionIndex  
  DisplayString as mdmManualDial  
  INTEGER as mdmTerminateCall  
  INTEGER as mdmDialStatus  
  INTEGER as mdmCallProgressStatus  

MdmDialingCellsFunctionEntry  
SEQUENCE    
  SCinstance as mdmDialCellFunctionIndex  
  INTEGER as mdmCellNumber  
  INTEGER as mdmDial  
  DisplayString as mdmCellPhoneNumber  
  INTEGER as mdmTerminateCellCall  

MdmMaintenanceEntry  
SEQUENCE    
  SCinstance as mdmMaintenanceIndex  
  INTEGER as mdmSaveRecallConfig  
  OCTET STRING as mdmConfigCksum  
  DisplayString as mdmPassword  
  DisplayString as mdmSerialNumber  
  INTEGER as mdmPowerUpProfile  
  INTEGER as mdmPasswordOperation  

MdmStatisticsEntry  
SEQUENCE    
  SCinstance as mdmStatisticsIndex  
  INTEGER as mdmDCERate  
  TimeTicks as mdmCallDurationStat  
  INTEGER as mdmRetrainCount  
  INTEGER as mdmFallbackCount  
  INTEGER as mdmFallforwardCount  
  INTEGER as mdmRxSignalLevel  
  INTEGER as mdmSignaltoNoiseRatio  
  INTEGER as mdmAnswerOriginateStat  
  INTEGER as mdmDiscReason  
  INTEGER as mdmCompressionEfficiency  
  INTEGER as mdmThruput  

MdmRemoteConfigEntry  
SEQUENCE    
  SCinstance as mdmRemoteConfigIndex  
  INTEGER as mdmRemoteConfiguration  
  INTEGER as mdmEndRemoteConfiguration  
  DisplayString as mdmPasswordRemoteConfiguration