
| RFC1155-SMI | RFC-1212 | HP-SN-ROOT-MIB |
| Counter | Gauge | IpAddress |
| OBJECT-TYPE | snBgp4 |
| snBgp4Gen | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1 | ||
| OBJECT IDENTIFIER | |||
| snBgp4GenAlwaysCompareMed | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.1 | ||
| To enable/disable the comparison of the Multi-Exit Discriminator for paths from neighbors in different AS. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4GenAutoSummary | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.2 | ||
| To enable/disable the default behavior of automatic summarization of subnet routes into network-level routes. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4GenDefaultLocalPreference | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.3 | ||
| To set the default local preference attribute. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenDefaultInfoOriginate | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.4 | ||
| To enable/disable the default Information Originate. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4GenFastExternalFallover | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.5 | ||
| To enable/disable an action of immediately reset the BGP sessions of any directly adjacent external neighbors if the link used to reach them goes down. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4GenNextBootNeighbors | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.6 | ||
| The next-boot configured number of neighbors in a BGP Peer Group. The minimum value of this MIB is snBgp4GenMinNeighbors. The maximum value of this MIB is snBgp4GenMaxNeighbors. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenNextBootRoutes | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.7 | ||
| The next-boot configured number of Routes. The minimum value of this MIB is snBgp4GenMinRoutes. The maximum value of this MIB is snBgp4GenMaxRoutes. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenSynchronization | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.8 | ||
| To enable/disable the synchronization between BGP and your IGP. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4GenKeepAliveTime | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.9 | ||
| The Keep alive timer. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| snBgp4GenHoldTime | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.10 | ||
| The Hold time timer. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| snBgp4GenRouterId | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.11 | ||
| BGP Router Id. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4GenTableMap | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.12 | ||
| An octet string of the route-map name, each character of the name is represented by one octet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..32) | ||
| snBgp4GenAdminStat | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.13 | ||
| The administrative status of BGP4 in the router. The value 'enabled' denotes that the BGP4 routing is active in this router; 'disabled' disables BGP4 routing on this router. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4GenDefaultMetric | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.14 | ||
| To set default metric values for the BGP4 protocol. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenMaxNeighbors | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.15 | ||
| The maximum number of neighbors can be configured in a BGP Peer Group. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenMinNeighbors | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.16 | ||
| The minimum number of neighbors can be configured in a BGP Peer Group. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenMaxRoutes | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.17 | ||
| The maximum configured number of Routes. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenMinRoutes | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.18 | ||
| The minimum configured number of Routes. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenMaxAddrFilters | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.19 | ||
| The maximum configured number of BGP4 address filters. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenMaxAggregateAddresses | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.20 | ||
| The maximum configured number of BGP4 aggregate addresses. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenMaxAsPathFilters | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.21 | ||
| The maximum configured number of BGP4 AS-PATH filters. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenMaxCommunityFilters | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.22 | ||
| The maximum configured number of BGP4 Community filters. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenMaxNetworks | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.23 | ||
| The maximum configured number of BGP4 Networks. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenMaxRouteMapFilters | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.24 | ||
| The maximum configured number of BGP4 Route-map Filters. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenNeighPrefixMinValue | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.25 | ||
| The minimum configured value of BGP4 Neighbor Prefix. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenOperNeighbors | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.26 | ||
| The current operational max number of neighbors configured for a BGP Group. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenOperRoutes | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.27 | ||
| The current operational number of Routes. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenLocalAs | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.28 | ||
| Bgp4 local autonomous system number. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| snBgp4GenRoutesInstalled | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.29 | ||
| Bgp4 installed routes. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenAsPathInstalled | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.30 | ||
| Bgp4 installed autonomous system path. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4ExternalDistance | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.31 | ||
| Administrative distance for BGP external routes. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| snBgp4InternalDistance | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.32 | ||
| Administrative distance for BGP internal routes. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| snBgp4LocalDistance | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.33 | ||
| Administrative distance for BGP local routes. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..255 | ||
| snBgp4OperNumOfAttributes | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.34 | ||
| The operational number of attribute entries. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4NextBootMaxAttributes | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.35 | ||
| The next boot maximum attribute entries. 10000 means reset to default. | |||
| OBJECT-TYPE | |||
| INTEGER | 200..30000 | ||
| snBgp4ClusterId | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.36 | ||
| A cluster ID which is represented by 4 bytes unsigned integer (0..0xFFFFFFFF). 0 means reset to default. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4ClientToClientReflection | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.37 | ||
| To enable/disable the client to client reflection in BGP4. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4GenTotalNeighbors | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.38 | ||
| The current total number of neighbors running in a BGP Group. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4GenMaxPaths | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.39 | ||
| The maximum configured number of Paths. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..8 | ||
| snBgp4GenConfedId | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.40 | ||
| Bgp4 Confederation Id. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| snBgp4GenConfedPeers | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.41 | ||
| An AS number from 1 to 0xFFFF construct confederation peers. There are 50(max peers) of them. This integer number is represented by 2 OCTETs. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..100) | ||
| snBgp4AddrFilter | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2 | ||
| OBJECT IDENTIFIER | |||
| snBgp4AddrFilterTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1 | ||
| Bgp4 Address Filter table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4AddrFilterEntry | |||
| snBgp4AddrFilterEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1 | ||
| An entry in the Bgp4 Address Filter table. | |||
| OBJECT-TYPE | |||
| SnBgp4AddrFilterEntry | |||
| snBgp4AddrFilterIndex | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.1 | ||
| The table index for a filter entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4AddrFilterAction | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.2 | ||
| Action to take if the bgp address match with this filter. | |||
| OBJECT-TYPE | |||
| INTEGER | deny(0), permit(1) | ||
| snBgp4AddrFilterSourceIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.3 | ||
| Source IP address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4AddrFilterSourceMask | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.4 | ||
| Source IP subnet mask. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4AddrFilterDestIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.5 | ||
| Destination IP address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4AddrFilterDestMask | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.6 | ||
| Destination IP subnet mask. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4AddrFilterRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.7 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snBgp4AggregateAddr | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3 | ||
| OBJECT IDENTIFIER | |||
| snBgp4AggregateAddrTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1 | ||
| Bgp4 Aggregate Address table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4AggregateAddrEntry | |||
| snBgp4AggregateAddrEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1 | ||
| An entry in the Bgp4 Aggregate Address table. | |||
| OBJECT-TYPE | |||
| SnBgp4AggregateAddrEntry | |||
| snBgp4AggregateAddrIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1.1 | ||
| Aggregate Address IP address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4AggregateAddrMask | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1.2 | ||
| Aggregate Address IP subnet mask. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4AggregateAddrOption | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1.3 | ||
| address(1), asSet(2), summaryOnly(3), the suppressMap(4), advertiseMap(5), attributeMap(6) are Options for creating an aggregate entry in a BGP routing table. | |||
| OBJECT-TYPE | |||
| INTEGER | address(1), asSet(2), summaryOnly(3), suppressMap(4), advertiseMap(5), attributeMap(6) | ||
| snBgp4AggregateAddrMap | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1.4 | ||
| This object associates with the snBgp4AggregateAddrOption and the suppressMap(4), advertiseMap(5), attributeMap(6) of the snBgp4AggregateAddrOption are only two Options for creating an aggregate address map. A SNMP-SET error will be returned for other options. An octet string of the map name, each character of the name is represented by one octet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..32) | ||
| snBgp4AggregateAddrRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1.5 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snBgp4AsPathFilter | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.4 | ||
| OBJECT IDENTIFIER | |||
| snBgp4AsPathFilterTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1 | ||
| Bgp4 AS-Path Filter table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4AsPathFilterEntry | |||
| snBgp4AsPathFilterEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1.1 | ||
| An entry in the Bgp4 As-path Filter table. | |||
| OBJECT-TYPE | |||
| SnBgp4AsPathFilterEntry | |||
| snBgp4AsPathFilterIndex | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1.1.1 | ||
| The table index for a filter entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4AsPathFilterAction | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1.1.2 | ||
| Action to take if the bgp address match with this filter. | |||
| OBJECT-TYPE | |||
| INTEGER | deny(0), permit(1) | ||
| snBgp4AsPathFilterRegExpression | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1.1.3 | ||
| Autonomous system in the filter using a regular expression. Each character of the regular expression string is represented by one octet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..256) | ||
| snBgp4AsPathFilterRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1.1.4 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snBgp4CommunityFilter | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5 | ||
| OBJECT IDENTIFIER | |||
| snBgp4CommunityFilterTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1 | ||
| Bgp4 Community Filter table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4CommunityFilterEntry | |||
| snBgp4CommunityFilterEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1 | ||
| An entry in the Bgp4 Community Filter table. | |||
| OBJECT-TYPE | |||
| SnBgp4CommunityFilterEntry | |||
| snBgp4CommunityFilterIndex | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.1 | ||
| The table index for a filter entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4CommunityFilterAction | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.2 | ||
| Action to take if the bgp address match with this filter. | |||
| OBJECT-TYPE | |||
| INTEGER | deny(0), permit(1) | ||
| snBgp4CommunityFilterCommNum | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.3 | ||
| A number from 1 to 0xFFFFFFFF. There are 20 of them. This integer number is represented by 4 OCTETs. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..80) | ||
| snBgp4CommunityFilterInternet | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.4 | ||
| Disabled/Enabled the Internet Community. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4CommunityFilterNoAdvertise | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.5 | ||
| Do not advertise this route to any peer (internal or external). | |||
| OBJECT-TYPE | |||
| INTEGER | false(0), true(1) | ||
| snBgp4CommunityFilterNoExport | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.6 | ||
| Do not advertise this route to an EBGP peer. | |||
| OBJECT-TYPE | |||
| INTEGER | false(0), true(1) | ||
| snBgp4CommunityFilterRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.7 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snBgp4CommunityFilterLocalAs | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.8 | ||
| Send this route to peers in other sub-autonomous systems within the local confederation. Do not advertise this route to an external system. | |||
| OBJECT-TYPE | |||
| INTEGER | false(0), true(1) | ||
| snBgp4NeighGenCfg | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6 | ||
| OBJECT IDENTIFIER | |||
| snBgp4NeighGenCfgTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1 | ||
| Bgp4 Neighbor General Configuration table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4NeighGenCfgEntry | |||
| snBgp4NeighGenCfgEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1 | ||
| An entry in the Bgp4 Community Filter table. | |||
| OBJECT-TYPE | |||
| SnBgp4NeighGenCfgEntry | |||
| snBgp4NeighGenCfgNeighIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.1 | ||
| The IP Address for a neighbor entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4NeighGenCfgAdvertlevel | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.2 | ||
| To set the minimum interval between the sending of BGP routing updates. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..600 | ||
| snBgp4NeighGenCfgDefOriginate | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.3 | ||
| To enable/disable the default originate for this neighbor. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4NeighGenCfgEbgpMultihop | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.4 | ||
| To enable/disable the EBGP Muitihop for this neighbor. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4NeighGenCfgMaxPrefix | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.5 | ||
| To control how many prefixes can be received from a neighbor. The minimum value of the maximum prefix is snBgp4GenNeighPrefixMinValue. The maximum value of the maximum prefix is snBgp4GenOperRoutes. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4NeighGenCfgNextHopSelf | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.6 | ||
| To enable/disable the next-hop processing of BGP updates on the router. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4NeighGenCfgRemoteAs | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.7 | ||
| To specify a neighbor with an autonomous system number(AS). | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| snBgp4NeighGenCfgSendComm | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.8 | ||
| To specify that a COMMUNITES attribute should be sent to a BGP neighbor. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4NeighGenCfgWeight | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.9 | ||
| To assign a weight to a neighbor connection. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| snBgp4NeighGenCfgWeightFilterList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.10 | ||
| A number from 1 to 0xFFFF. There are 16 of them. This integer number is represented by 2 OCTETs. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..32) | ||
| snBgp4NeighGenCfgRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.11 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row applyDefault(6)...apply default value to an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5), applyDefault(6) | ||
| snBgp4NeighGenCfgUpdateSrcLpbIntf | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.12 | ||
| To allow internal BGP sessions to use any operational loopback interface (1..8) for TCP connections. Zero interface means to restore the interface assignment to the closest interface, which is called the best local address. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..8 | ||
| snBgp4NeighGenCfgRouteRefClient | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.13 | ||
| To configure the router as a BGP route reflector, enable the specified neighbor as its client. When all the clients are disabled, the local router is no longer a route reflector. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4NeighGenCfgRemovePrivateAs | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.14 | ||
| To enable/disable filtering private AS number. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4NeighGenCfgEbgpMultihopTtl | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.15 | ||
| The EBGP Muitihop TTL for this neighbor. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| snBgp4NeighGenCfgShutdown | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.16 | ||
| To enable/disable BGP4 Nbr Shutdown. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4NeighGenCfgKeepAliveTime | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.17 | ||
| The Keep alive timer. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| snBgp4NeighGenCfgHoldTime | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.18 | ||
| The Hold time timer. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| snBgp4NeighDistGroup | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7 | ||
| OBJECT IDENTIFIER | |||
| snBgp4NeighDistGroupTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1 | ||
| Bgp4 Neighbor Distribute Group table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4NeighDistGroupEntry | |||
| snBgp4NeighDistGroupEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1 | ||
| An entry in the Bgp4 Distribute Group table. | |||
| OBJECT-TYPE | |||
| SnBgp4NeighDistGroupEntry | |||
| snBgp4NeighDistGroupNeighIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.1 | ||
| The IP Address for a neighbor entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4NeighDistGroupDir | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.2 | ||
| The incoming/outgoing advertisements to which the access list is applied. | |||
| OBJECT-TYPE | |||
| INTEGER | out(0), in(1) | ||
| snBgp4NeighDistGroupAccessList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.3 | ||
| A number from 1 to 0xFFFF. There are 16 of them. This integer number is represented by 2 OCTETs. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..32) | ||
| snBgp4NeighDistGroupRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.4 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snBgp4NeighFilterGroup | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8 | ||
| OBJECT IDENTIFIER | |||
| snBgp4NeighFilterGroupTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1 | ||
| Bgp4 Neighbor Filter Group table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4NeighFilterGroupEntry | |||
| snBgp4NeighFilterGroupEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1 | ||
| An entry in the Bgp4 Neighbor Filter Group table. | |||
| OBJECT-TYPE | |||
| SnBgp4NeighFilterGroupEntry | |||
| snBgp4NeighFilterGroupNeighIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.1 | ||
| The IP Address for a neighbor entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4NeighFilterGroupDir | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.2 | ||
| The incoming/outgoing advertisements to which the access list is applied. | |||
| OBJECT-TYPE | |||
| INTEGER | out(0), in(1) | ||
| snBgp4NeighFilterGroupAccessList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.3 | ||
| A number from 1 to 0xFFFF. There are 16 of them. This integer number is represented by 2 OCTETs. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..32) | ||
| snBgp4NeighFilterGroupRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.4 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snBgp4NeighRouteMap | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.9 | ||
| OBJECT IDENTIFIER | |||
| snBgp4NeighRouteMapTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1 | ||
| Bgp4 Neighbor Route Map table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4NeighRouteMapEntry | |||
| snBgp4NeighRouteMapEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1.1 | ||
| An entry in the Bgp4 Route Map table. | |||
| OBJECT-TYPE | |||
| SnBgp4NeighRouteMapEntry | |||
| snBgp4NeighRouteMapNeighIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1.1.1 | ||
| The IP Address for a neighbor entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4NeighRouteMapDir | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1.1.2 | ||
| The incoming/outgoing advertisements to which the access list is applied. | |||
| OBJECT-TYPE | |||
| INTEGER | out(0), in(1) | ||
| snBgp4NeighRouteMapMapName | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1.1.3 | ||
| An octet string of the route-map name, Each character of the name is represented by one octet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..32) | ||
| snBgp4NeighRouteMapRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1.1.4 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snBgp4Network | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10 | ||
| OBJECT IDENTIFIER | |||
| snBgp4NetworkTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1 | ||
| Bgp4 Network Weight table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4NetworkEntry | |||
| snBgp4NetworkEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1 | ||
| An entry in the Bgp4 Network Weight table. | |||
| OBJECT-TYPE | |||
| SnBgp4NetworkEntry | |||
| snBgp4NetworkIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1.1 | ||
| The IP Address for a network entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4NetworkSubnetMask | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1.2 | ||
| The subnet mask for a network entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4NetworkWeight | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1.3 | ||
| To assign a weight to a neighbor connection. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| snBgp4NetworkBackdoor | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1.4 | ||
| To enable/disable the backdoor for this network. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4NetworkRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1.5 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snBgp4Redis | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11 | ||
| OBJECT IDENTIFIER | |||
| snBgp4RedisTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1 | ||
| The BGP4 Redistribution contains configurations that could be imported into the BGP4 domain. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4RedisEntry | |||
| snBgp4RedisEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1 | ||
| The BGP4 Redistribution Entry specifies a particular RIP or , OSPF, or Static route to be imported into the BGP4 domain. | |||
| OBJECT-TYPE | |||
| SnBgp4RedisEntry | |||
| snBgp4RedisProtocol | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.1 | ||
| The imported configuration into BGP4 domain is set in the following: rip(1): - the RIP. ospf(2): - the OSPF. static(3): - the static. connected(4): - the connected. | |||
| OBJECT-TYPE | |||
| INTEGER | rip(1), ospf(2), static(3), connected(4) | ||
| snBgp4RedisMetric | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.2 | ||
| The metric of using the specified protocol Metric value. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RedisRouteMap | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.3 | ||
| An octet string of the route-map name, each character of the name is represented by one octet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..32) | ||
| snBgp4RedisWeight | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.4 | ||
| To assign a weight for the specified protocol. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| snBgp4RedisMatchInternal | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.5 | ||
| This object is only applicable to the OSPF protocol. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4RedisMatchExternal1 | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.6 | ||
| This object is only applicable to the OSPF protocol. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4RedisMatchExternal2 | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.7 | ||
| This object is only applicable to the OSPF protocol. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4RedisRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.8 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snBgp4RouteMapFilter | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.12 | ||
| OBJECT IDENTIFIER | |||
| snBgp4RouteMapFilterTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1 | ||
| Bgp4 RouteMap Filter table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4RouteMapFilterEntry | |||
| snBgp4RouteMapFilterEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1.1 | ||
| An entry in the Bgp4 RouteMap Filter table. | |||
| OBJECT-TYPE | |||
| SnBgp4RouteMapFilterEntry | |||
| snBgp4RouteMapFilterMapName | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1.1.1 | ||
| An octet string of the route-map name, each character of the name is represented by one octet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..32) | ||
| snBgp4RouteMapFilterSequenceNum | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1.1.2 | ||
| A sequence number for this particular route-map. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteMapFilterAction | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1.1.3 | ||
| Action to take if the bgp address match with this filter. | |||
| OBJECT-TYPE | |||
| INTEGER | deny(0), permit(1) | ||
| snBgp4RouteMapFilterRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1.1.4 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snBgp4RouteMapMatch | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13 | ||
| OBJECT IDENTIFIER | |||
| snBgp4RouteMapMatchTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1 | ||
| Bgp4 Route Map Set table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4RouteMapMatchEntry | |||
| snBgp4RouteMapMatchEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1 | ||
| An entry in the Bgp4 Route Map Match table. | |||
| OBJECT-TYPE | |||
| SnBgp4RouteMapMatchEntry | |||
| snBgp4RouteMapMatchMapName | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.1 | ||
| An octet string of the route-map name, each character of the name is represented by one octet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..32) | ||
| snBgp4RouteMapMatchSequenceNum | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.2 | ||
| A sequence number for this particular route-map. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteMapMatchAsPathFilter | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.3 | ||
| A number from 1 to 0xFFFF and there are 10 of 2 OCTETs. This integer number is represented by 2 OCTETs. To match a BGP autonomous system path access list. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..20) | ||
| snBgp4RouteMapMatchCommunityFilter | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.4 | ||
| A number from 1 to 0xFFFF and there are 10 of 2 OCTETs. This integer number is represented by 2 OCTETs. To match a BGP community access list. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..20) | ||
| snBgp4RouteMapMatchAddressFilter | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.5 | ||
| A number from 1 to 0xFFFF and there are 10 of 2 OCTETs. This integer number is represented by 2 OCTETs. To match a BGP address access list. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..20) | ||
| snBgp4RouteMapMatchMetric | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.6 | ||
| To match a metric for BGP routes. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteMapMatchNextHopList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.7 | ||
| A number from 1 to 0xFFFF and there are 16 of 2 OCTETs. This integer number is represented by 2 OCTETs. To match a BGP next-hop access list. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..32) | ||
| snBgp4RouteMapMatchRouteType | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.8 | ||
| To match a route-type. Currently only externalType1(2), externalType2(3), internal(4) is supported for SNMP-SET. | |||
| OBJECT-TYPE | |||
| INTEGER | none(0), external(1), externalType1(2), externalType2(3), internal(4), local(5) | ||
| snBgp4RouteMapMatchTagList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.9 | ||
| To match a BGP tag access list. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..32) | ||
| snBgp4RouteMapMatchRowMask | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.10 | ||
| This object is used together with above MIBs in the same VARBIND to set and reset any MIBs in the table. The bit number is referred to the snBgp4RouteMapMatchEntry number of each row in the table. The bit is ON - means set, The bit is OFF - means reset | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteMapSet | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14 | ||
| OBJECT IDENTIFIER | |||
| snBgp4RouteMapSetTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1 | ||
| Bgp4 Route Map Set table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4RouteMapSetEntry | |||
| snBgp4RouteMapSetEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1 | ||
| An entry in the Bgp4 Route Map Set table. | |||
| OBJECT-TYPE | |||
| SnBgp4RouteMapSetEntry | |||
| snBgp4RouteMapSetMapName | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.1 | ||
| An octet string of the route-map name, each character of the name is represented by one octet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..32) | ||
| snBgp4RouteMapSetSequenceNum | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.2 | ||
| A sequence number for this particular route-map. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteMapSetAsPathType | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.3 | ||
| To modify an autonomous system path for BGP routes. tag(0) - Converts the tag of a route into an autonomous system path. prepend(1) - Appends the string from snBgp4RouteMapSetAsPathString to the as-path of the route that is matched by the route map. | |||
| OBJECT-TYPE | |||
| INTEGER | tag(0), prepend(1) | ||
| snBgp4RouteMapSetAsPathString | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.4 | ||
| as-path string. This string is used if only if the snBgp4RouteMapSetAsPathCmd was sent together with the value set to prepend(1). | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..32) | ||
| snBgp4RouteMapSetAutoTag | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.5 | ||
| To enable/disable the automatic-tag for BGP routes. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4RouteMapSetCommunityType | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.6 | ||
| To set the BGP COMMUNITIES attribute. none means no other community attributes are allowed, nums means allowing community attributesi, the old values 1 and 2 are not valid since 5.03.00 | |||
| OBJECT-TYPE | |||
| INTEGER | nums(0), none(3) | ||
| snBgp4RouteMapSetCommunityNum | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.7 | ||
| community-number. This number is used if only if the snBgp4RouteMapSetCommunityCmd was sent together with the value set to number(0). | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteMapSetCommunityAdditive | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.8 | ||
| To add the community to the already existing communities. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snBgp4RouteMapSetLocalPreference | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.9 | ||
| To modify a local-preference for BGP routes. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteMapSetMetric | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.10 | ||
| To modify a metric for BGP routes. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteMapSetNextHop | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.11 | ||
| To modify the IP address of the next hop for BGP routes. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4RouteMapSetOrigin | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.12 | ||
| To set the BGP origin code. | |||
| OBJECT-TYPE | |||
| INTEGER | igp(0), egp(1), incomplete(2) | ||
| snBgp4RouteMapSetTag | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.13 | ||
| To specify the tag for BGP routes. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteMapSetWeight | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.14 | ||
| To specify the BGP weight for the routing table. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| snBgp4RouteMapSetRowMask | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.15 | ||
| This object is used together with above MIBs in the same VARBIND to set and reset any MIBs in the table. The bit number is referred to the snBgp4RouteMapSetEntry number of each row in the table. The bit is ON - means set, The bit is OFF - means reset | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteMapSetCommunityNums | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.16 | ||
| Community number is from 1 to 0xFFFFFFFF. There are 6 of them. This integer number is represented by 4 OCTETs. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..24) | ||
| snBgp4NeighOperStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15 | ||
| OBJECT IDENTIFIER | |||
| snBgp4NeighOperStatusTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1 | ||
| Bgp4 Neighbor Operational Status table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4NeighOperStatusEntry | |||
| snBgp4NeighOperStatusEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1 | ||
| An entry in the Bgp4 Operational Status table. | |||
| OBJECT-TYPE | |||
| SnBgp4NeighOperStatusEntry | |||
| snBgp4NeighOperStatusIndex | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.1 | ||
| The index for a neighbor entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4NeighOperStatusIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.2 | ||
| The IP Address for a neighbor entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4NeighOperStatusRemoteAs | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.3 | ||
| To show a neighbor with an autonomous system number(AS). | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4NeighOperStatusBgpType | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.4 | ||
| To show the type of BGP protocol whether is internal or external. | |||
| OBJECT-TYPE | |||
| INTEGER | ebgp(0), ibgp(1) | ||
| snBgp4NeighOperStatusState | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.5 | ||
| To show the state of this neighbor. | |||
| OBJECT-TYPE | |||
| INTEGER | noState(0), idle(1), connect(2), active(3), openSent(4), openConfirm(5), established(6) | ||
| snBgp4NeighOperStatusKeepAliveTime | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.6 | ||
| The Keep alive timer. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4NeighOperStatusHoldTime | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.7 | ||
| The Hold time timer. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4NeighOperStatusAdvertlevel | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.8 | ||
| To show the minimum interval between the sending of BGP routing updates. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4NeighOperStatusKeepAliveTxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.9 | ||
| Keep alive message sent counts. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snBgp4NeighOperStatusKeepAliveRxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.10 | ||
| Keep alive message received counts. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snBgp4NeighOperStatusUpdateTxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.11 | ||
| Update message sent counts. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snBgp4NeighOperStatusUpdateRxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.12 | ||
| Update message received counts. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snBgp4NeighOperStatusNotifTxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.13 | ||
| Notification message sent counts. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snBgp4NeighOperStatusNotifRxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.14 | ||
| Notification message received counts. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snBgp4NeighOperStatusOpenTxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.15 | ||
| Open message sent counts. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snBgp4NeighOperStatusOpenRxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.16 | ||
| Open message received counts. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snBgp4RouteOperStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16 | ||
| OBJECT IDENTIFIER | |||
| snBgp4RouteOperStatusTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1 | ||
| Bgp4 Routebor Operational Status table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4RouteOperStatusEntry | |||
| snBgp4RouteOperStatusEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1 | ||
| An entry in the Bgp4 Operational Status table. | |||
| OBJECT-TYPE | |||
| SnBgp4RouteOperStatusEntry | |||
| snBgp4RouteOperStatusIndex | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.1 | ||
| The index for a route entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteOperStatusIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.2 | ||
| The IP Address for a route entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4RouteOperStatusSubnetMask | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.3 | ||
| The IP Subnet Mask for a route entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4RouteOperStatusNextHop | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.4 | ||
| The next-hop IP for a route entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4RouteOperStatusMetric | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.5 | ||
| To show the metric value of a route entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteOperStatusLocalPreference | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.6 | ||
| To show the local preference of a route entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteOperStatusWeight | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.7 | ||
| To show the weight of this route. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteOperStatusOrigin | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.8 | ||
| To show the origin of this route. | |||
| OBJECT-TYPE | |||
| INTEGER | igp(0), egp(1), incomplete(2) | ||
| snBgp4RouteOperStatusStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.9 | ||
| A bit array that contains the status of this route. This is a packed bit string; The following shows the meaning of each bit: (bit 0 is the least significant bit and 0=FALSE, 1=TRUE). bit position meaning ------------ ------- 6-31 reserved. 5 aggregate. 4 best. 3 internal. 2 local. 1 suppressed. 0 valid. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteOperStatusRouteTag | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.10 | ||
| To show the route tag of this route. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4RouteOperStatusCommunityList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.11 | ||
| To show the community list of this route. If the community list is an NULL string that means an empty list, then the community is INTERNET. A number from 1 to 0xFFFFFFFF. This integer number is represented by 4 OCTETs. In the community list, it could have some Well-known numbers such as: BGP_COMMUNITY_ATTRIBUTE_NO_EXPORT 0xFFFFFF01 BGP_COMMUNITY_ATTRIBUTE_NO_ADVERTISE 0xFFFFFF02 | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| snBgp4RouteOperStatusAsPathList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.12 | ||
| To show the AS Path list of this route. A number from 1 to 0xFFFF. This integer number is represented by 2 OCTETs. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| snBgp4NeighborSummary | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17 | ||
| OBJECT IDENTIFIER | |||
| snBgp4NeighborSummaryTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1 | ||
| Bgp4 Routebor Operational Status table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4NeighborSummaryEntry | |||
| snBgp4NeighborSummaryEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1 | ||
| An entry in the Bgp4 Operational Status table. | |||
| OBJECT-TYPE | |||
| SnBgp4NeighborSummaryEntry | |||
| snBgp4NeighborSummaryIndex | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.1 | ||
| The index for a route entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4NeighborSummaryIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.2 | ||
| The IP Address for a route entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4NeighborSummaryState | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.3 | ||
| To show the state of this neighbor. | |||
| OBJECT-TYPE | |||
| INTEGER | noState(0), idle(1), connect(2), active(3), openSent(4), openConfirm(5), established(6) | ||
| snBgp4NeighborSummaryStateChgTime | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.4 | ||
| The time of a change of the state of this neighbor. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4NeighborSummaryRouteReceived | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.5 | ||
| The number of routes received of this neighbor. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4NeighborSummaryRouteInstalled | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.6 | ||
| The number of routes installed of this neighbor. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4Attribute | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18 | ||
| OBJECT IDENTIFIER | |||
| snBgp4AttributeTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1 | ||
| Bgp4 Attribute entries table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4AttributeEntry | |||
| snBgp4AttributeEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1 | ||
| An entry in the Bgp4 Attribute table. | |||
| OBJECT-TYPE | |||
| SnBgp4AttributeEntry | |||
| snBgp4AttributeIndex | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.1 | ||
| The index for a route entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4AttributeNextHop | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.2 | ||
| The next-hop IP for a route entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4AttributeMetric | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.3 | ||
| To show the metric value of a route entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4AttributeOrigin | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.4 | ||
| To show the origin of this route. | |||
| OBJECT-TYPE | |||
| INTEGER | igp(0), egp(1), incomplete(2) | ||
| snBgp4AttributeAggregatorAs | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.5 | ||
| The aggregator AS number for an attribute entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4AttributeRouterId | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.6 | ||
| The router ID for an attribute entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4AttributeAtomicAggregatePresent | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.7 | ||
| The atomic aggregate present in an attribute entry. | |||
| OBJECT-TYPE | |||
| INTEGER | false(0), true(1) | ||
| snBgp4AttributeLocalPreference | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.8 | ||
| To show the local preference of a route entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snBgp4AttributeCommunityList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.9 | ||
| To show the community list of this attribute entry. If the community list is an NULL string that means an empty list, then the community is INTERNET. A number from 1 to 0xFFFFFFFF. This integer number is represented by 4 OCTETs. In the community list, it could have some Well-known numbers such as: BGP_COMMUNITY_ATTRIBUTE_NO_EXPORT 0xFFFFFF01 BGP_COMMUNITY_ATTRIBUTE_NO_ADVERTISE 0xFFFFFF02 | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| snBgp4AttributeAsPathList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.10 | ||
| To show the AS Path list of this attribute entry. A number from 1 to 0xFFFF. This integer number is represented by 2 OCTETs. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| snBgp4AttributeOriginator | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.11 | ||
| The originator IP address for an attribute entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4AttributeClusterList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.12 | ||
| To show the cluster list of this attribute entry. If the cluster list is an NULL string, it means an empty list. Otherwise, the list is a group of cluster ID which is represented by 4 OCTETs IP address. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| snBgp4ClearNeighborCmd | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.19 | ||
| OBJECT IDENTIFIER | |||
| snBgp4ClearNeighborCmdTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.19.1 | ||
| Clear Bgp4 command table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnBgp4ClearNeighborCmdEntry | |||
| snBgp4ClearNeighborCmdEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.19.1.1 | ||
| An entry in the clear Bgp4 neighbor command table. | |||
| OBJECT-TYPE | |||
| SnBgp4ClearNeighborCmdEntry | |||
| snBgp4ClearNeighborCmdIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.19.1.1.1 | ||
| The IP Address for a neighbor entry. If the IP address is 255.255.255.255, it means for all neighbors. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snBgp4ClearNeighborCmdElement | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.19.1.1.2 | ||
| To send the command element of this neighbor for value(1) to (5) valid(0) is received in SNMP-get. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(0), lastPacketWithError(1), notificationErrors(2), softOutbound(3), traffic(4), neighbor(5) | ||
| SnBgp4AddrFilterEntry | |||
| SEQUENCE | |||
| INTEGER as snBgp4AddrFilterIndex | |||
| INTEGER as snBgp4AddrFilterAction | |||
| IpAddress as snBgp4AddrFilterSourceIp | |||
| IpAddress as snBgp4AddrFilterSourceMask | |||
| IpAddress as snBgp4AddrFilterDestIp | |||
| IpAddress as snBgp4AddrFilterDestMask | |||
| INTEGER as snBgp4AddrFilterRowStatus | |||
| SnBgp4AggregateAddrEntry | |||
| SEQUENCE | |||
| IpAddress as snBgp4AggregateAddrIp | |||
| IpAddress as snBgp4AggregateAddrMask | |||
| INTEGER as snBgp4AggregateAddrOption | |||
| OCTET STRING as snBgp4AggregateAddrMap | |||
| INTEGER as snBgp4AggregateAddrRowStatus | |||
| SnBgp4AsPathFilterEntry | |||
| SEQUENCE | |||
| INTEGER as snBgp4AsPathFilterIndex | |||
| INTEGER as snBgp4AsPathFilterAction | |||
| OCTET STRING as snBgp4AsPathFilterRegExpression | |||
| INTEGER as snBgp4AsPathFilterRowStatus | |||
| SnBgp4CommunityFilterEntry | |||
| SEQUENCE | |||
| INTEGER as snBgp4CommunityFilterIndex | |||
| INTEGER as snBgp4CommunityFilterAction | |||
| OCTET STRING as snBgp4CommunityFilterCommNum | |||
| INTEGER as snBgp4CommunityFilterInternet | |||
| INTEGER as snBgp4CommunityFilterNoAdvertise | |||
| INTEGER as snBgp4CommunityFilterNoExport | |||
| INTEGER as snBgp4CommunityFilterRowStatus | |||
| INTEGER as snBgp4CommunityFilterLocalAs | |||
| SnBgp4NeighGenCfgEntry | |||
| SEQUENCE | |||
| IpAddress as snBgp4NeighGenCfgNeighIp | |||
| INTEGER as snBgp4NeighGenCfgAdvertlevel | |||
| INTEGER as snBgp4NeighGenCfgDefOriginate | |||
| INTEGER as snBgp4NeighGenCfgEbgpMultihop | |||
| INTEGER as snBgp4NeighGenCfgMaxPrefix | |||
| INTEGER as snBgp4NeighGenCfgNextHopSelf | |||
| INTEGER as snBgp4NeighGenCfgRemoteAs | |||
| INTEGER as snBgp4NeighGenCfgSendComm | |||
| INTEGER as snBgp4NeighGenCfgWeight | |||
| OCTET STRING as snBgp4NeighGenCfgWeightFilterList | |||
| INTEGER as snBgp4NeighGenCfgRowStatus | |||
| INTEGER as snBgp4NeighGenCfgUpdateSrcLpbIntf | |||
| INTEGER as snBgp4NeighGenCfgRouteRefClient | |||
| INTEGER as snBgp4NeighGenCfgRemovePrivateAs | |||
| INTEGER as snBgp4NeighGenCfgEbgpMultihopTtl | |||
| INTEGER as snBgp4NeighGenCfgShutdown | |||
| INTEGER as snBgp4NeighGenCfgKeepAliveTime | |||
| INTEGER as snBgp4NeighGenCfgHoldTime | |||
| SnBgp4NeighDistGroupEntry | |||
| SEQUENCE | |||
| IpAddress as snBgp4NeighDistGroupNeighIp | |||
| INTEGER as snBgp4NeighDistGroupDir | |||
| OCTET STRING as snBgp4NeighDistGroupAccessList | |||
| INTEGER as snBgp4NeighDistGroupRowStatus | |||
| SnBgp4NeighFilterGroupEntry | |||
| SEQUENCE | |||
| IpAddress as snBgp4NeighFilterGroupNeighIp | |||
| INTEGER as snBgp4NeighFilterGroupDir | |||
| OCTET STRING as snBgp4NeighFilterGroupAccessList | |||
| INTEGER as snBgp4NeighFilterGroupRowStatus | |||
| SnBgp4NeighRouteMapEntry | |||
| SEQUENCE | |||
| IpAddress as snBgp4NeighRouteMapNeighIp | |||
| INTEGER as snBgp4NeighRouteMapDir | |||
| OCTET STRING as snBgp4NeighRouteMapMapName | |||
| INTEGER as snBgp4NeighRouteMapRowStatus | |||
| SnBgp4NetworkEntry | |||
| SEQUENCE | |||
| IpAddress as snBgp4NetworkIp | |||
| IpAddress as snBgp4NetworkSubnetMask | |||
| INTEGER as snBgp4NetworkWeight | |||
| INTEGER as snBgp4NetworkBackdoor | |||
| INTEGER as snBgp4NetworkRowStatus | |||
| SnBgp4RedisEntry | |||
| SEQUENCE | |||
| INTEGER as snBgp4RedisProtocol | |||
| INTEGER as snBgp4RedisMetric | |||
| OCTET STRING as snBgp4RedisRouteMap | |||
| INTEGER as snBgp4RedisWeight | |||
| INTEGER as snBgp4RedisMatchInternal | |||
| INTEGER as snBgp4RedisMatchExternal1 | |||
| INTEGER as snBgp4RedisMatchExternal2 | |||
| INTEGER as snBgp4RedisRowStatus | |||
| SnBgp4RouteMapFilterEntry | |||
| SEQUENCE | |||
| OCTET STRING as snBgp4RouteMapFilterMapName | |||
| INTEGER as snBgp4RouteMapFilterSequenceNum | |||
| INTEGER as snBgp4RouteMapFilterAction | |||
| INTEGER as snBgp4RouteMapFilterRowStatus | |||
| SnBgp4RouteMapMatchEntry | |||
| SEQUENCE | |||
| OCTET STRING as snBgp4RouteMapMatchMapName | |||
| INTEGER as snBgp4RouteMapMatchSequenceNum | |||
| OCTET STRING as snBgp4RouteMapMatchAsPathFilter | |||
| OCTET STRING as snBgp4RouteMapMatchCommunityFilter | |||
| OCTET STRING as snBgp4RouteMapMatchAddressFilter | |||
| INTEGER as snBgp4RouteMapMatchMetric | |||
| OCTET STRING as snBgp4RouteMapMatchNextHopList | |||
| INTEGER as snBgp4RouteMapMatchRouteType | |||
| OCTET STRING as snBgp4RouteMapMatchTagList | |||
| INTEGER as snBgp4RouteMapMatchRowMask | |||
| SnBgp4RouteMapSetEntry | |||
| SEQUENCE | |||
| OCTET STRING as snBgp4RouteMapSetMapName | |||
| INTEGER as snBgp4RouteMapSetSequenceNum | |||
| INTEGER as snBgp4RouteMapSetAsPathType | |||
| OCTET STRING as snBgp4RouteMapSetAsPathString | |||
| INTEGER as snBgp4RouteMapSetAutoTag | |||
| INTEGER as snBgp4RouteMapSetCommunityType | |||
| INTEGER as snBgp4RouteMapSetCommunityNum | |||
| INTEGER as snBgp4RouteMapSetCommunityAdditive | |||
| INTEGER as snBgp4RouteMapSetLocalPreference | |||
| INTEGER as snBgp4RouteMapSetMetric | |||
| IpAddress as snBgp4RouteMapSetNextHop | |||
| INTEGER as snBgp4RouteMapSetOrigin | |||
| INTEGER as snBgp4RouteMapSetTag | |||
| INTEGER as snBgp4RouteMapSetWeight | |||
| INTEGER as snBgp4RouteMapSetRowMask | |||
| OCTET STRING as snBgp4RouteMapSetCommunityNums | |||
| SnBgp4NeighOperStatusEntry | |||
| SEQUENCE | |||
| INTEGER as snBgp4NeighOperStatusIndex | |||
| IpAddress as snBgp4NeighOperStatusIp | |||
| INTEGER as snBgp4NeighOperStatusRemoteAs | |||
| INTEGER as snBgp4NeighOperStatusBgpType | |||
| INTEGER as snBgp4NeighOperStatusState | |||
| INTEGER as snBgp4NeighOperStatusKeepAliveTime | |||
| INTEGER as snBgp4NeighOperStatusHoldTime | |||
| INTEGER as snBgp4NeighOperStatusAdvertlevel | |||
| Counter as snBgp4NeighOperStatusKeepAliveTxCounts | |||
| Counter as snBgp4NeighOperStatusKeepAliveRxCounts | |||
| Counter as snBgp4NeighOperStatusUpdateTxCounts | |||
| Counter as snBgp4NeighOperStatusUpdateRxCounts | |||
| Counter as snBgp4NeighOperStatusNotifTxCounts | |||
| Counter as snBgp4NeighOperStatusNotifRxCounts | |||
| Counter as snBgp4NeighOperStatusOpenTxCounts | |||
| Counter as snBgp4NeighOperStatusOpenRxCounts | |||
| SnBgp4RouteOperStatusEntry | |||
| SEQUENCE | |||
| INTEGER as snBgp4RouteOperStatusIndex | |||
| IpAddress as snBgp4RouteOperStatusIp | |||
| IpAddress as snBgp4RouteOperStatusSubnetMask | |||
| IpAddress as snBgp4RouteOperStatusNextHop | |||
| INTEGER as snBgp4RouteOperStatusMetric | |||
| INTEGER as snBgp4RouteOperStatusLocalPreference | |||
| INTEGER as snBgp4RouteOperStatusWeight | |||
| INTEGER as snBgp4RouteOperStatusOrigin | |||
| INTEGER as snBgp4RouteOperStatusStatus | |||
| INTEGER as snBgp4RouteOperStatusRouteTag | |||
| OCTET STRING as snBgp4RouteOperStatusCommunityList | |||
| OCTET STRING as snBgp4RouteOperStatusAsPathList | |||
| SnBgp4NeighborSummaryEntry | |||
| SEQUENCE | |||
| INTEGER as snBgp4NeighborSummaryIndex | |||
| IpAddress as snBgp4NeighborSummaryIp | |||
| INTEGER as snBgp4NeighborSummaryState | |||
| INTEGER as snBgp4NeighborSummaryStateChgTime | |||
| INTEGER as snBgp4NeighborSummaryRouteReceived | |||
| INTEGER as snBgp4NeighborSummaryRouteInstalled | |||
| SnBgp4AttributeEntry | |||
| SEQUENCE | |||
| INTEGER as snBgp4AttributeIndex | |||
| IpAddress as snBgp4AttributeNextHop | |||
| INTEGER as snBgp4AttributeMetric | |||
| INTEGER as snBgp4AttributeOrigin | |||
| INTEGER as snBgp4AttributeAggregatorAs | |||
| IpAddress as snBgp4AttributeRouterId | |||
| INTEGER as snBgp4AttributeAtomicAggregatePresent | |||
| INTEGER as snBgp4AttributeLocalPreference | |||
| OCTET STRING as snBgp4AttributeCommunityList | |||
| OCTET STRING as snBgp4AttributeAsPathList | |||
| IpAddress as snBgp4AttributeOriginator | |||
| OCTET STRING as snBgp4AttributeClusterList | |||
| SnBgp4ClearNeighborCmdEntry | |||
| SEQUENCE | |||
| IpAddress as snBgp4ClearNeighborCmdIp | |||
| INTEGER as snBgp4ClearNeighborCmdElement | |||