HP-SN-IP-MIB

File: HP-SN-IP-MIB.mib (140547 bytes)

Imported modules

RFC1155-SMI RFC-1212 HP-SN-ROOT-MIB

Imported symbols

IpAddress Counter TimeTicks
OBJECT-TYPE snIp snRip
snDvmrp snFsrp snGblRt
snPim snVrrp snLoopbackIf

Defined Objects

snRtIpGeneral 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1
OBJECT IDENTIFIER    

snRtClearArpCache 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.1
clear(1) will clear arp cache table.
OBJECT-TYPE    
  ClearStatus  

snRtClearIpCache 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.2
clear(1) will clear ip route cache table.
OBJECT-TYPE    
  ClearStatus  

snRtClearIpRoute 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.3
clear(1) will clear ip route table.
OBJECT-TYPE    
  ClearStatus  

snRtBootpServer 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.4
IP address of bootp server to which bootp packet need to be relayed.
OBJECT-TYPE    
  IpAddress  

snRtBootpRelayMax 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.5
Maximum number of hop the bootp packet should travel.
OBJECT-TYPE    
  INTEGER 1..15  

snRtArpAge 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.6
The time in minutes an ARP entry can be valid without relearning. 0 - Don't not age.
OBJECT-TYPE    
  INTEGER 0..240  

snRtIpIrdpEnable 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.7
Perform router advertisement on this box.
OBJECT-TYPE    
  RtrStatus  

snRtIpLoadShare 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.8
If more than one route available, use them to share load.
OBJECT-TYPE    
  RtrStatus  

snRtIpProxyArp 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.9
Enable/disable proxy arp function in the box.
OBJECT-TYPE    
  RtrStatus  

snRtIpRarp 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.10
Enable/disable RARP server.
OBJECT-TYPE    
  RtrStatus  

snRtIpTtl 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.11
The time to live value to be used in IP header of IP packet generated by the box.
OBJECT-TYPE    
  INTEGER 1..255  

snRtIpSetAllPortConfig 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.12
The value of this object is an index number of a snRtIpPortConfigTable row (i.e. snRtIpPortConfigPortIndex), which is the selected row to copy all of its read-writable data (i.e. snRtIpPortMtu and snRtIpPortEncap) to the rest of the rows in snRtIpPortConfigTable. Note: prior setting this object, all the intended data of the given row of the table must be set. Otherwise, the current data of the row will be used to set the entire ip interface configuration table. The previous setting will be overwritten by the new one.
OBJECT-TYPE    
  INTEGER  

snRtIpFwdCacheMaxEntries 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.13
The maximum number of ip forwarding table entries.
OBJECT-TYPE    
  INTEGER  

snRtIpFwdCacheCurEntries 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.14
The current number of ip forwarding table entries.
OBJECT-TYPE    
  INTEGER  

snRtIpMaxStaticRouteEntries 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.15
The maximum number of static route entries in the static route table.
OBJECT-TYPE    
  INTEGER  

snRtIpDirBcastFwd 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.16
Enable/Disable directed broadcast forwarding.
OBJECT-TYPE    
  RtrStatus  

snRtIpLoadShareNumOfPaths 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.17
Number of routes are used to share load.
OBJECT-TYPE    
  INTEGER  

snRtIpLoadShareMaxPaths 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.18
Maximum number of routes can be configured to share load.
OBJECT-TYPE    
  INTEGER  

snRtIpLoadShareMinPaths 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.19
Minimum number of routes can be configured to share load.
OBJECT-TYPE    
  INTEGER  

snRtIpProtocolRouterId 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.20
Router Id for all IP Protocols.
OBJECT-TYPE    
  IpAddress  

snRtIpSourceRoute 1.3.6.1.4.1.11.2.3.7.11.12.2.2.1.21
Enable/Disable source routing support, ability to drop the source routing packets.
OBJECT-TYPE    
  RtrStatus  

snRtIpStaticRouteTable 1.3.6.1.4.1.11.2.3.7.11.12.2.2.2
IP static/default route table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtIpStaticRouteEntry

snRtIpStaticRouteEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.2.2.1
An entry in the IP static route table.
OBJECT-TYPE    
  SnRtIpStaticRouteEntry  

snRtIpStaticRouteIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.2.2.1.1
The table index for a static route entry.
OBJECT-TYPE    
  INTEGER  

snRtIpStaticRouteDest 1.3.6.1.4.1.11.2.3.7.11.12.2.2.2.1.2
Destination IP address. 0.0.0.0 for default route.
OBJECT-TYPE    
  IpAddress  

snRtIpStaticRouteMask 1.3.6.1.4.1.11.2.3.7.11.12.2.2.2.1.3
Subnet mask associated with the destination IP address. 0.0.0.0 for default route mask.
OBJECT-TYPE    
  IpAddress  

snRtIpStaticRouteNextHop 1.3.6.1.4.1.11.2.3.7.11.12.2.2.2.1.4
IP address of next hop router that is located on one of the directly attached IP subnet.
OBJECT-TYPE    
  IpAddress  

snRtIpStaticRouteMetric 1.3.6.1.4.1.11.2.3.7.11.12.2.2.2.1.5
The metrics to next hop router.
OBJECT-TYPE    
  INTEGER  

snRtIpStaticRouteRowStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.2.2.1.6
To create or delete a static route entry.
OBJECT-TYPE    
  RowSts  

snRtIpStaticRouteDistance 1.3.6.1.4.1.11.2.3.7.11.12.2.2.2.1.7
Administration distance.
OBJECT-TYPE    
  INTEGER 1..255  

snRtIpFilterTable 1.3.6.1.4.1.11.2.3.7.11.12.2.2.3
IP filter table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtIpFilterEntry

snRtIpFilterEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.2.3.1
An entry in the IP filter table.
OBJECT-TYPE    
  SnRtIpFilterEntry  

snRtIpFilterIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.2.3.1.1
The table index for a filter entry.
OBJECT-TYPE    
  INTEGER  

snRtIpFilterAction 1.3.6.1.4.1.11.2.3.7.11.12.2.2.3.1.2
Action to take if the ip packet match with this filter.
OBJECT-TYPE    
  INTEGER deny(0), permit(1), qosEnabled(2)  

snRtIpFilterProtocol 1.3.6.1.4.1.11.2.3.7.11.12.2.2.3.1.3
Transport protocol. 0 means don't care
OBJECT-TYPE    
  INTEGER 0..255  

snRtIpFilterSourceIp 1.3.6.1.4.1.11.2.3.7.11.12.2.2.3.1.4
Source IP address.
OBJECT-TYPE    
  IpAddress  

snRtIpFilterSourceMask 1.3.6.1.4.1.11.2.3.7.11.12.2.2.3.1.5
Source IP subnet mask.
OBJECT-TYPE    
  IpAddress  

snRtIpFilterDestIp 1.3.6.1.4.1.11.2.3.7.11.12.2.2.3.1.6
Destination IP address.
OBJECT-TYPE    
  IpAddress  

snRtIpFilterDestMask 1.3.6.1.4.1.11.2.3.7.11.12.2.2.3.1.7
Destination IP subnet mask.
OBJECT-TYPE    
  IpAddress  

snRtIpFilterOperator 1.3.6.1.4.1.11.2.3.7.11.12.2.2.3.1.8
Type of comparison to perform. for now, this only applys to tcp or udp to compare the port number
OBJECT-TYPE    
  INTEGER greater(1), equal(2), less(3), notEqual(4)  

snRtIpFilterOperand 1.3.6.1.4.1.11.2.3.7.11.12.2.2.3.1.9
For now this only refers to transport protocol port number. 0 means NA
OBJECT-TYPE    
  INTEGER 0..65535  

snRtIpFilterRowStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.2.3.1.10
To create or delete a filter entry.
OBJECT-TYPE    
  RowSts  

snRtIpFilterEstablished 1.3.6.1.4.1.11.2.3.7.11.12.2.2.3.1.11
Enable/Disable the filtering of established TCP packets of which the ACK or RESET flag is on. This additional filter only applies to TCP transport protocol.
OBJECT-TYPE    
  RtrStatus  

snRtIpFilterQosPriority 1.3.6.1.4.1.11.2.3.7.11.12.2.2.3.1.12
The router L4 Qos Priority values are: low(0) -- low prority high(1) -- high prority. The Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)
OBJECT-TYPE    
  INTEGER level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)  

snRtIpRarpTable 1.3.6.1.4.1.11.2.3.7.11.12.2.2.4
IP RARP table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtIpRarpEntry

snRtIpRarpEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.2.4.1
An entry in the IP Rarp table.
OBJECT-TYPE    
  SnRtIpRarpEntry  

snRtIpRarpIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.2.4.1.1
The table index for a Rarp entry.
OBJECT-TYPE    
  INTEGER 1..16  

snRtIpRarpMac 1.3.6.1.4.1.11.2.3.7.11.12.2.2.4.1.2
The Mac address for a Rarp entry.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

snRtIpRarpIp 1.3.6.1.4.1.11.2.3.7.11.12.2.2.4.1.3
The IP address for a Rarp entry.
OBJECT-TYPE    
  IpAddress  

snRtIpRarpRowStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.2.4.1.4
To create or delete a Rarp entry.
OBJECT-TYPE    
  RowSts  

snRtStaticArpTable 1.3.6.1.4.1.11.2.3.7.11.12.2.2.5
IP static arp table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtStaticArpEntry

snRtStaticArpEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.2.5.1
An entry in the IP static arp table.
OBJECT-TYPE    
  SnRtStaticArpEntry  

snRtStaticArpIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.2.5.1.1
The table index for a static arp entry.
OBJECT-TYPE    
  INTEGER 1..16  

snRtStaticArpIp 1.3.6.1.4.1.11.2.3.7.11.12.2.2.5.1.2
The IP address for a static arp entry.
OBJECT-TYPE    
  IpAddress  

snRtStaticArpMac 1.3.6.1.4.1.11.2.3.7.11.12.2.2.5.1.3
The Mac address for a static arp entry.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

snRtStaticArpPort 1.3.6.1.4.1.11.2.3.7.11.12.2.2.5.1.4
The port index for a static arp entry.
OBJECT-TYPE    
  PortIndex  

snRtStaticArpRowStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.2.5.1.5
To create or delete a Static Arp entry.
OBJECT-TYPE    
  RowSts  

snRtIpPortAddrTable 1.3.6.1.4.1.11.2.3.7.11.12.2.2.6
IP port address table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtIpPortAddrEntry

snRtIpPortAddrEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.2.6.1
An entry in the IP Port Address table.
OBJECT-TYPE    
  SnRtIpPortAddrEntry  

snRtIpPortAddrPortIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.2.6.1.1
The port index for port address entry.
OBJECT-TYPE    
  PortIndex  

snRtIpPortAddress 1.3.6.1.4.1.11.2.3.7.11.12.2.2.6.1.2
The port IP address.
OBJECT-TYPE    
  IpAddress  

snRtIpPortSubnetMask 1.3.6.1.4.1.11.2.3.7.11.12.2.2.6.1.3
The port IP address subnet mask.
OBJECT-TYPE    
  IpAddress  

snRtIpPortAddrType 1.3.6.1.4.1.11.2.3.7.11.12.2.2.6.1.4
The port IP address type.
OBJECT-TYPE    
  INTEGER primary(1), secondary(2)  

snRtIpPortRowStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.2.6.1.5
To create or delete a port address entry.
OBJECT-TYPE    
  RowSts  

snRtIpPortAccessTable 1.3.6.1.4.1.11.2.3.7.11.12.2.2.7
IP port access table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtIpPortAccessEntry

snRtIpPortAccessEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.2.7.1
An entry in the IP Port access table.
OBJECT-TYPE    
  SnRtIpPortAccessEntry  

snRtIpPortAccessPortIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.2.7.1.1
The port index for port access entry.
OBJECT-TYPE    
  PortIndex  

snRtIpPortAccessDirection 1.3.6.1.4.1.11.2.3.7.11.12.2.2.7.1.2
The incoming or outgoing check for port access.
OBJECT-TYPE    
  INTEGER in(1), out(2)  

snRtIpPortAccessFilters 1.3.6.1.4.1.11.2.3.7.11.12.2.2.7.1.3
1st octet correspond to 1st filter number and so on.
OBJECT-TYPE    
  OCTET STRING  

snRtIpPortAccessRowStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.2.7.1.4
To create or delete a port access entry.
OBJECT-TYPE    
  RowSts  

snRtIpPortConfigTable 1.3.6.1.4.1.11.2.3.7.11.12.2.2.8
IP port Config table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtIpPortConfigEntry

snRtIpPortConfigEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.2.8.1
An entry in the IP Port Config table.
OBJECT-TYPE    
  SnRtIpPortConfigEntry  

snRtIpPortConfigPortIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.2.8.1.1
The port index for port config entry.
OBJECT-TYPE    
  PortIndex  

snRtIpPortMtu 1.3.6.1.4.1.11.2.3.7.11.12.2.2.8.1.2
The maximun transfer unit.
OBJECT-TYPE    
  INTEGER 576..4470  

snRtIpPortEncap 1.3.6.1.4.1.11.2.3.7.11.12.2.2.8.1.3
Data link encapsulation to be used on the IP frame transmitted on the port.
OBJECT-TYPE    
  INTEGER ethernet(1), snap(2), hdlc(3), ppp(4)  

snRtIpPortMetric 1.3.6.1.4.1.11.2.3.7.11.12.2.2.8.1.4
The metric.
OBJECT-TYPE    
  INTEGER 1..15  

snRtIpPortDirBcastFwd 1.3.6.1.4.1.11.2.3.7.11.12.2.2.8.1.5
Enable/Disable directed broadcast forwarding on the port.
OBJECT-TYPE    
  RtrStatus  

snRtBcastFwd 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9
OBJECT IDENTIFIER    

snRtBcastFwdGeneral 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9.1
OBJECT IDENTIFIER    

snRtUdpBcastFwdEnable 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9.1.1
Enable or disable UDP broadcast forwarding service. When UDP broadcast forwarding is enabled, default entries are added to the UDP broadcast forwarding port table. When it is disabled, UDP broadcast forwarding port table is flushed to empty.
OBJECT-TYPE    
  RtrStatus  

snRtUdpBcastFwdPort 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9.2
OBJECT IDENTIFIER    

snRtUdpBcastFwdPortTable 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9.2.1
This table contains a list of UDP port numbers for which forwarding UDP broadcast is enabled.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtUdpBcastFwdPortEntry

snRtUdpBcastFwdPortEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9.2.1.1
An entry of the UDP broadcast forwarding port table.
OBJECT-TYPE    
  SnRtUdpBcastFwdPortEntry  

snRtUdpBcastFwdPortIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9.2.1.1.1
The table index for a UDP broadcast forwarding port entry.
OBJECT-TYPE    
  INTEGER 1..20  

snRtUdpBcastFwdPortNumber 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9.2.1.1.2
UDP port number for which UDP broadcast forwarding is enabled.
OBJECT-TYPE    
  INTEGER 1..65535  

snRtUdpBcastFwdPortRowStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9.2.1.1.3
To create or delete a UDP broadcast forwarding port entry.
OBJECT-TYPE    
  RowSts  

snRtUdpHelper 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9.3
OBJECT IDENTIFIER    

snRtUdpHelperTable 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9.3.1
UDP helper table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtUdpHelperEntry

snRtUdpHelperEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9.3.1.1
An entry of the UDP helper table.
OBJECT-TYPE    
  SnRtUdpHelperEntry  

snRtUdpHelperPortIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9.3.1.1.1
The port index for a UDP helper entry.
OBJECT-TYPE    
  PortIndex  

snRtUdpHelperIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9.3.1.1.2
The table index for a UDP helper entry.
OBJECT-TYPE    
  INTEGER 1..4  

snRtUdpHelperAddr 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9.3.1.1.3
The UDP helper address. This is the address that UDP packets will be forwarded. It can be a helper address or a subnet broadcast address. But it cannot be 255.255.255.255 or 0.0.0.0.
OBJECT-TYPE    
  IpAddress  

snRtUdpHelperRowStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.2.9.3.1.1.4
To create or delete a UDP helper entry.
OBJECT-TYPE    
  RowSts  

snRtIpTraceRoute 1.3.6.1.4.1.11.2.3.7.11.12.2.2.10
OBJECT IDENTIFIER    

snRtIpTraceRouteGeneral 1.3.6.1.4.1.11.2.3.7.11.12.2.2.10.1
OBJECT IDENTIFIER    

snRtIpTraceRouteTargetAddr 1.3.6.1.4.1.11.2.3.7.11.12.2.2.10.1.1
Target IP address of which trace route is performed.
OBJECT-TYPE    
  IpAddress  

snRtIpTraceRouteMinTtl 1.3.6.1.4.1.11.2.3.7.11.12.2.2.10.1.2
Minimum TTL value carried in the first probe packet.
OBJECT-TYPE    
  INTEGER 1..255  

snRtIpTraceRouteMaxTtl 1.3.6.1.4.1.11.2.3.7.11.12.2.2.10.1.3
Maximum TTL value carried in the last probe packet.
OBJECT-TYPE    
  INTEGER 1..255  

snRtIpTraceRouteTimeOut 1.3.6.1.4.1.11.2.3.7.11.12.2.2.10.1.4
Time out period (in seconds) to wait for the response from the probe packet (i,e, the ICMP packet).
OBJECT-TYPE    
  INTEGER 1..120  

snRtIpTraceRouteControl 1.3.6.1.4.1.11.2.3.7.11.12.2.2.10.1.5
Only 'start' and 'abort' are writable values; 'success', 'failure' and 'inProgress' are readeable (or returned) values. Writing 'start' to this object to initiate the trace route operation. snRtIpTraceRouteDestAddr must have been init- ialized before 'start' is writen. This object will return 'inProgress' after trace route operation has started. During the 'inProgress' state, writing 'abort' to this object will stop the current trace route operation. If the destination address is reached, this object returned 'success'. snRtIpTraceRouteResultTable contains the routes (and the target address) to reach the destination address. If the destination address does not reach, timeout, or ending TTL reached, 'failure' is returned.
OBJECT-TYPE    
  INTEGER start(1), abort(2), success(3), failure(4), inProgress(5)  

snRtIpTraceRouteResult 1.3.6.1.4.1.11.2.3.7.11.12.2.2.10.2
OBJECT IDENTIFIER    

snRtIpTraceRouteResultTable 1.3.6.1.4.1.11.2.3.7.11.12.2.2.10.2.1
Trace route result table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtIpTraceRouteResultEntry

snRtIpTraceRouteResultEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.2.10.2.1.1
An entry of the trace route result table.
OBJECT-TYPE    
  SnRtIpTraceRouteResultEntry  

snRtIpTraceRouteResultIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.2.10.2.1.1.1
The table index for a trace route result entry.
OBJECT-TYPE    
  INTEGER  

snRtIpTraceRouteResultAddr 1.3.6.1.4.1.11.2.3.7.11.12.2.2.10.2.1.1.2
The router or the target address of which forms part of the route to reach the destination address.
OBJECT-TYPE    
  IpAddress  

snRtIpTraceRouteResultRoundTripTime1 1.3.6.1.4.1.11.2.3.7.11.12.2.2.10.2.1.1.3
The round trip time between the first probe packet transmitted and the reponse ICMP packet received.
OBJECT-TYPE    
  TimeTicks  

snRtIpTraceRouteResultRoundTripTime2 1.3.6.1.4.1.11.2.3.7.11.12.2.2.10.2.1.1.4
The round trip time between the second probe packet transmitted and the reponse ICMP packet received.
OBJECT-TYPE    
  TimeTicks  

snRtIpFwdCacheTable 1.3.6.1.4.1.11.2.3.7.11.12.2.2.11
IP forwarding cache table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtIpFwdCacheEntry

snRtIpFwdCacheEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.2.11.1
An entry in the IP forwarding cache table.
OBJECT-TYPE    
  SnRtIpFwdCacheEntry  

snRtIpFwdCacheIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.2.11.1.1
The table index for a ip forwarding cache table entry.
OBJECT-TYPE    
  INTEGER  

snRtIpFwdCacheIp 1.3.6.1.4.1.11.2.3.7.11.12.2.2.11.1.2
The IP address of a station.
OBJECT-TYPE    
  IpAddress  

snRtIpFwdCacheMac 1.3.6.1.4.1.11.2.3.7.11.12.2.2.11.1.3
The Mac address of an IP station.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

snRtIpFwdCacheNextHopIp 1.3.6.1.4.1.11.2.3.7.11.12.2.2.11.1.4
The next hop router IP address.
OBJECT-TYPE    
  IpAddress  

snRtIpFwdCacheOutgoingPort 1.3.6.1.4.1.11.2.3.7.11.12.2.2.11.1.5
The outgoing port of which packets will forward to. Return port value of zero to indicate no outgoing port associated to this entry. Non-zero value has the following meanings: The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number. For virtual router interface, slot number is 15, port number is the virtual router port from 1 to 60.
OBJECT-TYPE    
  INTEGER 0..3900  

snRtIpFwdCacheType 1.3.6.1.4.1.11.2.3.7.11.12.2.2.11.1.6
The 'dynamic' or 'permanent' type for a ip forwarding cache table entry.
OBJECT-TYPE    
  INTEGER dynamic(1), permanent(2)  

snRtIpFwdCacheAction 1.3.6.1.4.1.11.2.3.7.11.12.2.2.11.1.7
The action to take.
OBJECT-TYPE    
  INTEGER other(1), forward(2), forUs(3), waitForArp(4), complexFilter(5), icmpDeny(6), dropPacket(7)  

snRtIpFwdCacheFragCheck 1.3.6.1.4.1.11.2.3.7.11.12.2.2.11.1.8
Check for fragmentation.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snRtIpFwdCacheSnapHdr 1.3.6.1.4.1.11.2.3.7.11.12.2.2.11.1.9
Apply SNAP encapsulation.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snRtIpFwdCacheVLanId 1.3.6.1.4.1.11.2.3.7.11.12.2.2.11.1.10
The VLAN ID for a ip forwarding cache table entry. Return VLAN ID value of zero to indicate no VLAN associated to this entry.
OBJECT-TYPE    
  INTEGER  

snRtIpRipGeneral 1.3.6.1.4.1.11.2.3.7.11.12.2.3.1
OBJECT IDENTIFIER    

snRtIpRipEnable 1.3.6.1.4.1.11.2.3.7.11.12.2.3.1.1
Enable/disable ip rip routing.
OBJECT-TYPE    
  RtrStatus  

snRtIpRipUpdateTime 1.3.6.1.4.1.11.2.3.7.11.12.2.3.1.2
Ip rip update interval in seconds.
OBJECT-TYPE    
  INTEGER 1..1000  

snRtIpRipRedisEnable 1.3.6.1.4.1.11.2.3.7.11.12.2.3.1.3
Enable/disable redistribution to rip.
OBJECT-TYPE    
  RtrStatus  

snRtIpRipRedisDefMetric 1.3.6.1.4.1.11.2.3.7.11.12.2.3.1.4
Default metric to be used when redistribute route to rip.
OBJECT-TYPE    
  INTEGER 1..15  

snRtIpRipSetAllPortConfig 1.3.6.1.4.1.11.2.3.7.11.12.2.3.1.5
The value of this object is an index number of a snRtIpRipPortConfigTable row (i.e. snRtIpRipPortConfigPortIndex), which is the selected row to copy all of its read-writable data (i.e. snRtIpRipPortVersion and snRtIpRipPortPoisonReverse) to the rest of the rows in snRtIpRipPortConfigTable. Note: prior setting this object, all the intended data of the given row of the table must be set. Otherwise, the current data of the row will be used to set the entire ip rip port configuration table. The previous setting will be overwritten by the new one.
OBJECT-TYPE    
  INTEGER  

snRtIpRipGblFiltList 1.3.6.1.4.1.11.2.3.7.11.12.2.3.1.6
An ip rip global filter list, of which each octet contains a filter ID number that forms a group of filters. A valid entry in the snRtIpRipRouteFilterTable with the corresponding filter ID number (i.e. snRtIpRipRouteFilterId) must have been created before a filter list is initialized.
OBJECT-TYPE    
  OCTET STRING SIZE(1..64)  

snRtIpRipFiltOnAllPort 1.3.6.1.4.1.11.2.3.7.11.12.2.3.1.7
Apply the ip rip global filter list snRtIpRipGblFiltList to all interfaces. This object is used to add all rip filter lists and delete all rip filter lists to/from all interfaces. Prior to sending this command, snRtIpRipGblFiltList must have been set to a proper filter list. The values that can be written are: deleteAllInBound(2)...delete all in-bound filter lists from all ports. deleteAllOutBound(3)..delete all out-bound filter lists from all ports. addAllInBound(4)......add all in-bound filter lists to all ports. addAllOutBound(5).....add all out-bound filter lists to all ports. If set operation failed, then a SET with value of (2) or (3) returns error code 'GenError'. If succeed, entries in the filter list are deleted immediately. The following values can be returned on reads: valid(1)....set operation is done and is valid.
OBJECT-TYPE    
  INTEGER valid(1), deleteAllInBound(2), deleteAllOutBound(3), addAllInBound(4), addAllOutBound(5)  

snRtIpRipDistance 1.3.6.1.4.1.11.2.3.7.11.12.2.3.1.8
Administration distance.
OBJECT-TYPE    
  INTEGER 1..255  

snRtIpRipPortConfigTable 1.3.6.1.4.1.11.2.3.7.11.12.2.3.2
IP Rip port Config table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtIpRipPortConfigEntry

snRtIpRipPortConfigEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.3.2.1
An entry in the IP Rip Port Config table.
OBJECT-TYPE    
  SnRtIpRipPortConfigEntry  

snRtIpRipPortConfigPortIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.3.2.1.1
The port index for ip rip port config entry.
OBJECT-TYPE    
  PortIndex  

snRtIpRipPortVersion 1.3.6.1.4.1.11.2.3.7.11.12.2.3.2.1.2
The ip rip version on this port.
OBJECT-TYPE    
  INTEGER disabled(0), v1Only(1), v2Only(2), v1CompatibleV2(3)  

snRtIpRipPortPoisonReverse 1.3.6.1.4.1.11.2.3.7.11.12.2.3.2.1.3
Enable/disable poison reverse.
OBJECT-TYPE    
  RtrStatus  

snRtIpRipPortLearnDefault 1.3.6.1.4.1.11.2.3.7.11.12.2.3.2.1.4
Apply the RIP router protocol learn-default option to the interface. The values that can be written are: disabled(0)...deleted the learn default option. enabled(1)....enabled the learn default option.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snRtIpRipRedisTable 1.3.6.1.4.1.11.2.3.7.11.12.2.3.3
IP Rip Redistribution table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtIpRipRedisEntry

snRtIpRipRedisEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.3.3.1
An entry in the IP Rip Redistribution table.
OBJECT-TYPE    
  SnRtIpRipRedisEntry  

snRtIpRipRedisIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.3.3.1.1
The table index for a IP Rip Redistribution entry.
OBJECT-TYPE    
  INTEGER 1..64  

snRtIpRipRedisAction 1.3.6.1.4.1.11.2.3.7.11.12.2.3.3.1.2
The action to take when match this IP Rip Redistribution entry.
OBJECT-TYPE    
  Action  

snRtIpRipRedisProtocol 1.3.6.1.4.1.11.2.3.7.11.12.2.3.3.1.3
The protocol to be distributed. other(1) cannot be used for SNMP-SET.
OBJECT-TYPE    
  INTEGER other(1), all(2), static(3), ospf(4), bgp(5)  

snRtIpRipRedisIp 1.3.6.1.4.1.11.2.3.7.11.12.2.3.3.1.4
The ip address of the ip route to be distributed. 0.0.0.0 - all routes
OBJECT-TYPE    
  IpAddress  

snRtIpRipRedisMask 1.3.6.1.4.1.11.2.3.7.11.12.2.3.3.1.5
The ip subnet mask of the ip route to be distributed.
OBJECT-TYPE    
  IpAddress  

snRtIpRipRedisMatchMetric 1.3.6.1.4.1.11.2.3.7.11.12.2.3.3.1.6
The metric of the route to be matched to determine the redistribution. 0 - any metric value
OBJECT-TYPE    
  Metric  

snRtIpRipRedisSetMetric 1.3.6.1.4.1.11.2.3.7.11.12.2.3.3.1.7
The new metric of the route to be advertised. 0 - use the default metric.
OBJECT-TYPE    
  INTEGER 0..15  

snRtIpRipRedisRowStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.3.3.1.8
To create or delete a Redistribution entry.
OBJECT-TYPE    
  RowSts  

snRtIpRipRouteFilterTable 1.3.6.1.4.1.11.2.3.7.11.12.2.3.4
ip rip route filter table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtIpRipRouteFilterEntry

snRtIpRipRouteFilterEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.3.4.1
An entry of the ip rip route filter table.
OBJECT-TYPE    
  SnRtIpRipRouteFilterEntry  

snRtIpRipRouteFilterId 1.3.6.1.4.1.11.2.3.7.11.12.2.3.4.1.1
The filter ID to identify a filter entry.
OBJECT-TYPE    
  INTEGER 1..64  

snRtIpRipRouteFilterAction 1.3.6.1.4.1.11.2.3.7.11.12.2.3.4.1.2
Action to take if the ip rip packet matched with this filter.
OBJECT-TYPE    
  Action  

snRtIpRipRouteFilterIpAddr 1.3.6.1.4.1.11.2.3.7.11.12.2.3.4.1.3
Route IP address to compare with any route IP addresses in a ip rip packet. IP address 0.0.0.0 always compare equals to any route IP addresses in any ip rip packets.
OBJECT-TYPE    
  IpAddress  

snRtIpRipRouteFilterSubnetMask 1.3.6.1.4.1.11.2.3.7.11.12.2.3.4.1.4
Subnet mask to apply to the route IP address in a ip rip packet, the result is compared to snRtIpRipRouteFilterIpAddr. If snRtIpRipRouteFilterIpAddr is 0.0.0.0, this subnet mask value is ignored.
OBJECT-TYPE    
  IpAddress  

snRtIpRipRouteFilterRowStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.3.4.1.5
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2).....the row exists and is valid
OBJECT-TYPE    
  INTEGER invalid(1), valid(2), delete(3), create(4), modify(5)  

snRtIpRipNbrFilterTable 1.3.6.1.4.1.11.2.3.7.11.12.2.3.5
ip rip neighbor filter table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtIpRipNbrFilterEntry

snRtIpRipNbrFilterEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.3.5.1
An entry of the ip rip neighbor filter table.
OBJECT-TYPE    
  SnRtIpRipNbrFilterEntry  

snRtIpRipNbrFilterId 1.3.6.1.4.1.11.2.3.7.11.12.2.3.5.1.1
The filter ID to identify a filter entry.
OBJECT-TYPE    
  INTEGER 1..64  

snRtIpRipNbrFilterAction 1.3.6.1.4.1.11.2.3.7.11.12.2.3.5.1.2
Action to take if the ip rip packet source IP address compares equal to the source IP address in this filter.
OBJECT-TYPE    
  Action  

snRtIpRipNbrFilterSourceIp 1.3.6.1.4.1.11.2.3.7.11.12.2.3.5.1.3
Source IP address to compare with the source IP address in a ip rip packet. IP address 0.0.0.0 always compares equal to any source IP addresses in any ip rip packets.
OBJECT-TYPE    
  IpAddress  

snRtIpRipNbrFilterRowStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.3.5.1.4
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2).....the row exists and is valid
OBJECT-TYPE    
  INTEGER invalid(1), valid(2), delete(3), create(4), modify(5)  

snRtIpRipPortAccessTable 1.3.6.1.4.1.11.2.3.7.11.12.2.3.6
ip interface rip access table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnRtIpRipPortAccessEntry

snRtIpRipPortAccessEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.3.6.1
An entry of the ip interface rip access table.
OBJECT-TYPE    
  SnRtIpRipPortAccessEntry  

snRtIpRipPortAccessPort 1.3.6.1.4.1.11.2.3.7.11.12.2.3.6.1.1
The ip interface to which the rip filter applies.
OBJECT-TYPE    
  PortIndex  

snRtIpRipPortAccessDir 1.3.6.1.4.1.11.2.3.7.11.12.2.3.6.1.2
The access direction of incoming packet filter or outgoing packet filter.
OBJECT-TYPE    
  INTEGER in(1), out(2)  

snRtIpRipPortAccessFilterList 1.3.6.1.4.1.11.2.3.7.11.12.2.3.6.1.3
An ip rip filter list, of which each octet contains a filter ID number that forms a group of filters. A valid entry in the snRtIpRipRouteFilterTable with the corresponding filter ID number (i.e. snRtIpRipRouteFilterId) must have been created before a filter list is initialized.
OBJECT-TYPE    
  OCTET STRING SIZE(1..64)  

snRtIpRipPortAccessRowStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.3.6.1.4
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2).....the row exists and is valid
OBJECT-TYPE    
  INTEGER invalid(1), valid(2), delete(3), create(4), modify(5)  

snDvmrpMIBObjects 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1
OBJECT IDENTIFIER    

snDvmrpVersion 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.1
The router's DVMRP version information.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

snDvmrpEnable 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.2
Enable or disable DVMRP on this router.
OBJECT-TYPE    
  RtrStatus  

snDvmrpGenerationId 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.3
The generation identifier for the routing process. This is used by neighboring routers to detect whether pruning information should be resent.
OBJECT-TYPE    
  INTEGER  

snDvmrpProbeInterval 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.4
This is the time interval at which the router sends out probe messages to discover neighbour routers. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
OBJECT-TYPE    
  INTEGER 5..30  

snDvmrpReportInterval 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.5
This is the time interval at which the router sends out full report messages. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
OBJECT-TYPE    
  INTEGER 10..2000  

snDvmrpTriggerInterval 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.6
This is the time interval at which triggered updates are sent out. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
OBJECT-TYPE    
  INTEGER 5..30  

snDvmrpNeighborRouterTimeout 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.7
This is the time interval after which the neighbour router is considered down. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
OBJECT-TYPE    
  INTEGER 60..8000  

snDvmrpRouteExpireTime 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.8
This is the time interval after which the route expires and becomes unreachable. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
OBJECT-TYPE    
  INTEGER 20..4000  

snDvmrpRouteDiscardTime 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.9
This is the time interval after which a route is discarded from the route table. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
OBJECT-TYPE    
  INTEGER 40..8000  

snDvmrpPruneAge 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.10
This is the duration of time for which the prune state is stored. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
OBJECT-TYPE    
  INTEGER 20..3600  

snDvmrpGraftRetransmitTime 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.11
This is the time interval after which a graft message will be retransmitted if graft acknowledge message has not been received. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
OBJECT-TYPE    
  INTEGER 5..3600  

snDvmrpDefaultRoute 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.12
This is the IP address of a router that is connected to one of the directly attached subnet. If a multicast route is not present on the local router, this default route will be used for multicast forwarding. snDvmrpEnable must be 'enabled' before this object is writen.
OBJECT-TYPE    
  IpAddress  

snDvmrpVInterfaceTable 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.13
The (conceptual) table listing the router's DVMRP virtual interfaces. snDvmrpEnable must be 'enabled' before this table is read or writen.
OBJECT-TYPE    
  SEQUENCE OF  
    SnDvmrpVInterfaceEntry

snDvmrpVInterfaceEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.13.1
An entry (conceptual row) in the snDvmrpVInterfaceTable. This row augments ipMRouteInterfaceEntry in the IP Multicast MIB, where the threshold object resides.
OBJECT-TYPE    
  SnDvmrpVInterfaceEntry  

snDvmrpVInterfaceVifIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.13.1.1
The ifIndex value of this DVMRP virtual interface.
OBJECT-TYPE    
  INTEGER 1..48  

snDvmrpVInterfaceType 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.13.1.2
The type of this DVMRP virtual interface, whether it uses a tunnel, a physical interface for which we are a querier, or a physical interface for which we are not a querier. For write operation, this object can only accept tunnel(1) to configure a tunnel interface or subnet(3) to configure a physical interface.
OBJECT-TYPE    
  INTEGER tunnel(1), querier(2), subnet(3)  

snDvmrpVInterfaceOperState 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.13.1.3
The current operational state of this DVMRP virtual interface.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

snDvmrpVInterfaceLocalAddress 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.13.1.4
The IP address of the local end of this DVMRP virtual interface.
OBJECT-TYPE    
  IpAddress  

snDvmrpVInterfaceRemoteAddress 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.13.1.5
The IP address of the remote end of this DVMRP virtual interface. For a tunnel, this is the IP address of the neighboring router. For a subnet, this is the subnet address.
OBJECT-TYPE    
  IpAddress  

snDvmrpVInterfaceRemoteSubnetMask 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.13.1.6
The subnet mask for a directly connected subnet. For a tunnel, this should be 0.0.0.0.
OBJECT-TYPE    
  IpAddress  

snDvmrpVInterfaceMetric 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.13.1.7
The distance metric for this DVMRP virtual interface which is used to calculate distance vectors.
OBJECT-TYPE    
  INTEGER 1..31  

snDvmrpVInterfaceTtlThreshold 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.13.1.8
This is the minimum time-to-live value to forward the packets out of this virtual interface.
OBJECT-TYPE    
  INTEGER 1..254  

snDvmrpVInterfaceAdvertiseLocal 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.13.1.9
Enable or disable the advertising of this local route.
OBJECT-TYPE    
  RtrStatus  

snDvmrpVInterfaceEncapsulation 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.13.1.10
Enable or disable the encapsulation of the DVMRP control packets when using IPINIP encapsulation.
OBJECT-TYPE    
  RtrStatus  

snDvmrpVInterfaceStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.13.1.11
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2)....Setting it to 'valid' has the effect of changing the row to operative.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2), delete(3), create(4), modify(5)  

snDvmrpNeighborTable 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.14
The (conceptual) table listing the router's DVMRP neighbors, as discovered by receiving Neighbor Probe messages. snDvmrpEnable must be 'enabled' before this table is read.
OBJECT-TYPE    
  SEQUENCE OF  
    SnDvmrpNeighborEntry

snDvmrpNeighborEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.14.1
An entry (conceptual row) in the snDvmrpNeighborTable.
OBJECT-TYPE    
  SnDvmrpNeighborEntry  

snDvmrpNeighborEntryIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.14.1.1
The table entry index.
OBJECT-TYPE    
  INTEGER  

snDvmrpNeighborVifIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.14.1.2
The value of VifIndex for the virtual interface used to reach this DVMRP neighbor.
OBJECT-TYPE    
  INTEGER  

snDvmrpNeighborAddress 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.14.1.3
The IP address of the DVMRP neighbor for which this entry contains information.
OBJECT-TYPE    
  IpAddress  

snDvmrpNeighborUpTime 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.14.1.4
The time since this DVMRP neighbor (last) became a neighbor of the local router.
OBJECT-TYPE    
  TimeTicks  

snDvmrpNeighborExpiryTime 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.14.1.5
The minimum time remaining before this DVMRP neighbor will be aged out.
OBJECT-TYPE    
  TimeTicks  

snDvmrpNeighborGenerationId 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.14.1.6
The neighboring router's generation identifier.
OBJECT-TYPE    
  INTEGER  

snDvmrpNeighborMajorVersion 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.14.1.7
The neighboring router's major DVMRP version number.
OBJECT-TYPE    
  INTEGER 0..255  

snDvmrpNeighborMinorVersion 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.14.1.8
The neighboring router's minor DVMRP version number.
OBJECT-TYPE    
  INTEGER 0..255  

snDvmrpNeighborCapabilities 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.14.1.9
This object describes the neighboring router's capabilities. The following shows the position of each bit: bit position meaning ----------- ------ 3 mtrace bit 2 generationID bit 1 prune bit 0 leaf bit The leaf bit indicates that the neighbor has only one interface with neighbors. The prune bit indicates that the neighbor supports pruning. The generationID bit indicates that the neighbor sends its generationID in Probe messages. The mtrace bit indicates that the neighbor can handle mtrace requests.
OBJECT-TYPE    
  INTEGER  

snDvmrpRouteTable 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.15
The routing table used by DVMRP in place of the unicast routing table. snDvmrpEnable must be 'enabled' before this table is read.
OBJECT-TYPE    
  SEQUENCE OF  
    SnDvmrpRouteEntry

snDvmrpRouteEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.15.1
An entry (conceptual row) containing the multicast routing information used by DVMRP in place of the unicast routing information.
OBJECT-TYPE    
  SnDvmrpRouteEntry  

snDvmrpRouteEntryIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.15.1.1
The table entry index.
OBJECT-TYPE    
  INTEGER  

snDvmrpRouteSource 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.15.1.2
The network address which when combined with the corresponding value of snDvmrpRouteSourceMask identifies the sources for which this entry contains multicast routing information.
OBJECT-TYPE    
  IpAddress  

snDvmrpRouteSourceMask 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.15.1.3
The network mask which when combined with the corresponding value of snDvmrpRouteSource identifies the sources for which this entry contains multicast routing information.
OBJECT-TYPE    
  IpAddress  

snDvmrpRouteUpstreamNeighbor 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.15.1.4
The address of the upstream neighbor (e.g., RPF neighbor) from which IP datagrams from these sources are received.
OBJECT-TYPE    
  IpAddress  

snDvmrpRouteVifIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.15.1.5
The value of snDvmrpVInterfaceVifIndex for the virtual interface on which IP datagrams sent by these sources are received.
OBJECT-TYPE    
  INTEGER  

snDvmrpRouteMetric 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.15.1.6
The distance in hops to the source subnet.
OBJECT-TYPE    
  INTEGER  

snDvmrpRouteExpiryTime 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.15.1.7
The minimum amount of time remaining before this entry will be aged out.
OBJECT-TYPE    
  TimeTicks  

snDvmrpRouteNextHopTable 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.16
The (conceptual) table containing information on the next hops on outgoing interfaces for routing IP multicast datagrams. snDvmrpEnable must be 'enabled' before this table is read.
OBJECT-TYPE    
  SEQUENCE OF  
    SnDvmrpRouteNextHopEntry

snDvmrpRouteNextHopEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.16.1
An entry (conceptual row) in the list of next hops on outgoing interfaces to which IP multicast datagrams from particular sources are routed.
OBJECT-TYPE    
  SnDvmrpRouteNextHopEntry  

snDvmrpRouteNextHopSource 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.16.1.1
The network address which when combined with the corresponding value of snDvmrpRouteNextHopSourceMask identifies the sources for which this entry specifies a next hop on an outgoing interface.
OBJECT-TYPE    
  IpAddress  

snDvmrpRouteNextHopSourceMask 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.16.1.2
The network mask which when combined with the corresponding value of snDvmrpRouteNextHopSource identifies the sources for which this entry specifies a next hop on an outgoing interface.
OBJECT-TYPE    
  IpAddress  

snDvmrpRouteNextHopVifIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.16.1.3
The snDvmrpVInterfaceVifIndex value of the virtual interface for the outgoing interface for this next hop.
OBJECT-TYPE    
  INTEGER  

snDvmrpRouteNextHopType 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.16.1.4
Type is leaf if no neighbors exist on the outgoing virtual interface. Otherwise, type is branch.
OBJECT-TYPE    
  INTEGER leaf(1), branch(2)  

snDvmrpVIfStatTable 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17
The (conceptual) table listing the router's DVMRP virtual interface statistical counters. snDvmrpEnable must be 'enabled' before this table is read.
OBJECT-TYPE    
  SEQUENCE OF  
    SnDvmrpVIfStatEntry

snDvmrpVIfStatEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1
An entry (conceptual row) in the snDvmrpVIfStatTable.
OBJECT-TYPE    
  SnDvmrpVIfStatEntry  

snDvmrpVIfStatVifIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.1
The ifIndex value of this DVMRP virtual interface.
OBJECT-TYPE    
  INTEGER 1..65535  

snDvmrpVIfStatInPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.2
The number of packets that have arrived on the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatOutPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.3
The number of packets that have been sent on the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatInOctets 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.4
The number of octets that have arrived on the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatOutOctets 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.5
The number of octets that have been sent on the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatInProbePkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.6
The number of probe packets that have arrived on the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatOutProbePkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.7
The number of probe packets that have been sent on the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatDiscardProbePkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.8
The number of probe packets that have been discarded by the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatInRtUpdatePkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.9
The number of route update packets that have arrived on the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatOutRtUpdatePkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.10
The number of route update packets that have been sent on the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatDiscardRtUpdatePkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.11
The number of route update packets that have been discarded by the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatInGraftPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.12
The number of graft packets that have arrived on the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatOutGraftPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.13
The number of graft packets that have been sent on the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatDiscardGraftPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.14
The number of graft packets that have been discarded by the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatInGraftAckPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.15
The number of graft acknowledge packets that have arrived on the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatOutGraftAckPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.16
The number of graft acknowledge packets that have been sent on the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatDiscardGraftAckPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.17
The number of graft acknowledge packets that have been discarded by the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatInPrunePkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.18
The number of prune packets that have arrived on the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatOutPrunePkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.19
The number of prune packets that have been sent on the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snDvmrpVIfStatDiscardPrunePkts 1.3.6.1.4.1.11.2.3.7.11.12.2.5.1.17.1.20
The number of prune packets that have been discarded by the DVMRP virtual interface.
OBJECT-TYPE    
  Counter  

snFsrpGlobal 1.3.6.1.4.1.11.2.3.7.11.12.2.7.1
OBJECT IDENTIFIER    

snFsrpGroupOperMode 1.3.6.1.4.1.11.2.3.7.11.12.2.7.1.1
The FSRP is configured on this system either enabled or disabled and the default is disabled mode. disabled(0)..........disable FSRP enabled(1)...........activate FSRP
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snFsrpIfStateChangeTrap 1.3.6.1.4.1.11.2.3.7.11.12.2.7.1.2
Indicates whether the SNMP agent process is permitted to generate FSRP interface state change traps.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snFsrpIntf 1.3.6.1.4.1.11.2.3.7.11.12.2.7.2
OBJECT IDENTIFIER    

snFsrpIfTable 1.3.6.1.4.1.11.2.3.7.11.12.2.7.2.1
The FSRP Interface Table describes the interfaces from the viewpoint of FSRP.
OBJECT-TYPE    
  SEQUENCE OF  
    SnFsrpIfEntry

snFsrpIfEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.7.2.1.1
The FSRP Interface Entry describes one interface from the viewpoint of FSRP.
OBJECT-TYPE    
  SnFsrpIfEntry  

snFsrpIfPort 1.3.6.1.4.1.11.2.3.7.11.12.2.7.2.1.1.1
The physical router port of this FSRP interface.
OBJECT-TYPE    
  INTEGER  

snFsrpIfIpAddress 1.3.6.1.4.1.11.2.3.7.11.12.2.7.2.1.1.2
The IP Address of the physical router port of this interface.
OBJECT-TYPE    
  IpAddress  

snFsrpIfVirRtrIpAddr 1.3.6.1.4.1.11.2.3.7.11.12.2.7.2.1.1.3
The IP Address of the Virtual Router for the interface. The Virtual Router IP address need to be configured on the interface before Redundant Router Function can operate on the interface. This address has to be same on all the routers that going to participate in the Redundant Router Function on a given subnet.
OBJECT-TYPE    
  IpAddress  

snFsrpIfOtherRtrIpAddr 1.3.6.1.4.1.11.2.3.7.11.12.2.7.2.1.1.4
The IP Address of the Other Router on this ip subnet that operates FSRP and to whom the Keep Alive message need to be sent by this router. This object must be configured for FSRP to work correctly
OBJECT-TYPE    
  IpAddress  

snFsrpIfPreferLevel 1.3.6.1.4.1.11.2.3.7.11.12.2.7.2.1.1.5
The higher the number the higher the priority is. This parameter decides which router should becomes the Active Router for the interface. A Router with higher priority selected to becomes the Active Router.
OBJECT-TYPE    
  INTEGER 1..255  

snFsrpIfTrackPortMask 1.3.6.1.4.1.11.2.3.7.11.12.2.7.2.1.1.6
This object specifies the identity of the physical port whose state is to be monitored. Each bit is a port of the system. Default value is 0. If this object is configured then the Preference Level of this interface will be adjusted dynamically depending on the state of the Track Port. The interface's Preference Level is reduced by value of Preference Level parameter when the Track Port states first changes from UP to DOWN. When the Track Port next comes up the interface's Preference Level is increased by the amount specified by the Preference Level. The Standalone router FSRP Track port membership (Not used for Chassis Product)
OBJECT-TYPE    
  PortMask  

snFsrpIfRowStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.7.2.1.1.7
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
OBJECT-TYPE    
  INTEGER invalid(1), valid(2), delete(3), create(4), modify(5)  

snFsrpIfState 1.3.6.1.4.1.11.2.3.7.11.12.2.7.2.1.1.8
This object specifies the FSRP Router's interface state as: init(0)...initialization state. negotiating(1)...negotiating state. standby(2)...standby state. active(3)...active state.
OBJECT-TYPE    
  INTEGER init(0), negotiating(1), standby(2), active(3)  

snFsrpIfKeepAliveTime 1.3.6.1.4.1.11.2.3.7.11.12.2.7.2.1.1.9
The heart-beat is from 1 to 120 seconds.
OBJECT-TYPE    
  INTEGER 1..120  

snFsrpIfRouterDeadTime 1.3.6.1.4.1.11.2.3.7.11.12.2.7.2.1.1.10
The hold time of the Fsrp router is from 3 to 255 seconds.
OBJECT-TYPE    
  INTEGER 3..255  

snFsrpIfChassisTrackPortMask 1.3.6.1.4.1.11.2.3.7.11.12.2.7.2.1.1.11
This object specifies the identity of the physical port whose state is to be monitored. Each bit is a port of the system. Default value is 0. If this object is configured then the Preference Level of this interface will be adjusted dynamically depending on the state of the Track Port. The interface's Preference Level is reduced by value of Preference Level parameter when the Track Port states first changes from UP to DOWN. When the Track Port next comes up the interface's Preference Level is increased by the amount specified by the Preference Level. The Chassis router FSRP Track port membership
OBJECT-TYPE    
  OCTET STRING SIZE(32)  

snGblRtGeneral 1.3.6.1.4.1.11.2.3.7.11.12.2.8.1
OBJECT IDENTIFIER    

snGblRtRouteOnly 1.3.6.1.4.1.11.2.3.7.11.12.2.8.1.1
If this object is 'enabled', this switching router will only route packets. If this object is 'disabled', this switching router will first route packets. If route cannot perform, it will switch packets.
OBJECT-TYPE    
  RtrStatus  

snPimMIBObjects 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1
OBJECT IDENTIFIER    

snPimEnable 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.1
Enable or disable PIM on this router.
OBJECT-TYPE    
  RtrStatus  

snPimNeighborRouterTimeout 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.2
This is the time interval after which the neighbour router is considered down. Value is in number of seconds. snPimEnable must be 'enabled' before this object is writen.
OBJECT-TYPE    
  INTEGER 60..8000  

snPimHelloTime 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.3
This is the interval at which hello message is sent out an interface to the neighbouring router. This is used to detect the presence or abscense of a neighbouring router. Value is in number of seconds. snPimEnable must be 'enabled' before this object is writen.
OBJECT-TYPE    
  INTEGER 10..3600  

snPimPruneTime 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.4
This is the duration of time for which the prune state is stored. Value is in number of seconds. snPimEnable must be 'enabled' before this object is writen.
OBJECT-TYPE    
  INTEGER 10..3600  

snPimGraftRetransmitTime 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.5
This is the time interval after which a graft message will be retransmitted if graft acknowledge message has not been received. Value is in number of seconds. snPimEnable must be 'enabled' before this object is writen.
OBJECT-TYPE    
  INTEGER 10..3600  

snPimInactivityTime 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.6
This is the interval after which the forwarding entry is deleted. When a packet is received for a group entry, this time is reset. This is used to only keep the forwarding entries for the active sessions. Value is in number of seconds. snPimEnable must be 'enabled' before this object is writen.
OBJECT-TYPE    
  INTEGER 10..3600  

snPimVInterfaceTable 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.7
The (conceptual) table listing the router's PIM virtual interfaces. snPimEnable must be 'enabled' before this table is read or writen.
OBJECT-TYPE    
  SEQUENCE OF  
    SnPimVInterfaceEntry

snPimVInterfaceEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.7.1
An entry (conceptual row) in the snPimVInterfaceTable.
OBJECT-TYPE    
  SnPimVInterfaceEntry  

snPimVInterfaceVifIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.7.1.1
The ifIndex value of this PIM virtual interface.
OBJECT-TYPE    
  INTEGER 1..48  

snPimVInterfaceType 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.7.1.2
The type of PIM virtual interface, whether it uses a tunnel or a physical interface.
OBJECT-TYPE    
  INTEGER tunnel(1), subnet(2)  

snPimVInterfaceLocalAddress 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.7.1.3
The IP address of the local end of this PIM virtual interface.
OBJECT-TYPE    
  IpAddress  

snPimVInterfaceLocalSubnetMask 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.7.1.4
The network mask for the IP address of the PIM virtual interface. For a tunnel, this should be 0.0.0.0.
OBJECT-TYPE    
  IpAddress  

snPimVInterfaceRemoteAddress 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.7.1.5
The IP address of the remote end of this PIM virtual interface.
OBJECT-TYPE    
  IpAddress  

snPimVInterfaceDR 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.7.1.6
The Designated Router on this PIM virtual interface. For point-to-point interfaces, this object has the value 0.0.0.0.
OBJECT-TYPE    
  IpAddress  

snPimVInterfaceTtlThreshold 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.7.1.7
This is the minimum time-to-live value to forward the packets out of this interface.
OBJECT-TYPE    
  INTEGER 1..31  

snPimVInterfaceStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.7.1.8
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2)....Setting it to 'valid' has the effect of changing the row to operative.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2), delete(3), create(4), modify(5)  

snPimNeighborTable 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.8
The (conceptual) table listing the router's PIM neighbors. snPimEnable must be 'enabled' before this table is read.
OBJECT-TYPE    
  SEQUENCE OF  
    SnPimNeighborEntry

snPimNeighborEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.8.1
An entry (conceptual row) in the snPimNeighborTable.
OBJECT-TYPE    
  SnPimNeighborEntry  

snPimNeighborEntryIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.8.1.1
The table entry index.
OBJECT-TYPE    
  INTEGER  

snPimNeighborVifIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.8.1.2
The value of VifIndex for the virtual interface used to reach this PIM neighbor.
OBJECT-TYPE    
  INTEGER  

snPimNeighborAddress 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.8.1.3
The IP address of the PIM neighbor for which this entry contains information.
OBJECT-TYPE    
  IpAddress  

snPimNeighborUpTime 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.8.1.4
The time since this PIM neighbor (last) became a neighbor of the local router.
OBJECT-TYPE    
  TimeTicks  

snPimNeighborExpiryTime 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.8.1.5
The minimum time remaining before this PIM neighbor will be aged out.
OBJECT-TYPE    
  TimeTicks  

snPimVIfStatTable 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9
The (conceptual) table listing the router's PIM virtual interface statistical counters. snPimEnable must be 'enabled' before this table is read.
OBJECT-TYPE    
  SEQUENCE OF  
    SnPimVIfStatEntry

snPimVIfStatEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1
An entry (conceptual row) in the snPimVIfStatTable.
OBJECT-TYPE    
  SnPimVIfStatEntry  

snPimVIfStatVifIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.1
The ifIndex value of this PIM virtual interface.
OBJECT-TYPE    
  INTEGER 1..32  

snPimVIfStatInJoinPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.2
The number of join packets that have arrived on the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatOutJoinPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.3
The number of join packets that have been sent on the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatDiscardJoinPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.4
The number of join packets that have been discarded by the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatInPrunePkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.5
The number of prune packets that have arrived on the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatOutPrunePkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.6
The number of prune packets that have been sent on the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatDiscardPrunePkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.7
The number of prune packets that have been discarded by the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatInAssertPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.8
The number of assert packets that have arrived on the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatOutAssertPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.9
The number of assert packets that have been sent on the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatDiscardAssertPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.10
The number of assert packets that have been discarded by the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatInHelloPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.11
The number of hello packets that have arrived on the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatOutHelloPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.12
The number of hello packets that have been sent on the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatDiscardHelloPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.13
The number of hello packets that have been discarded by the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatInGraftPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.14
The number of graft packets that have arrived on the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatOutGraftPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.15
The number of graft packets that have been sent on the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatDiscardGraftPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.16
The number of graft packets that have been discarded by the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatInGraftAckPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.17
The number of graft acknowledge packets that have arrived on the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatOutGraftAckPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.18
The number of graft acknowledge packets that have been sent on the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snPimVIfStatDiscardGraftAckPkts 1.3.6.1.4.1.11.2.3.7.11.12.2.9.1.9.1.19
The number of graft acknowledge packets that have been discarded by the PIM virtual interface.
OBJECT-TYPE    
  Counter  

snVrrpGlobal 1.3.6.1.4.1.11.2.3.7.11.12.2.12.1
OBJECT IDENTIFIER    

snVrrpGroupOperMode 1.3.6.1.4.1.11.2.3.7.11.12.2.12.1.1
The VRRP is configured on this system either enabled or disabled and the default is disabled mode. disabled(0)..........disable VRRP enabled(1)...........activate VRRP
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snVrrpIfStateChangeTrap 1.3.6.1.4.1.11.2.3.7.11.12.2.12.1.2
Indicates whether the SNMP agent process is permitted to generate VRRP interface state change traps.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snVrrpIfMaxNumVridPerIntf 1.3.6.1.4.1.11.2.3.7.11.12.2.12.1.3
Indicates the maximum number of VRID per interface.
OBJECT-TYPE    
  INTEGER  

snVrrpIfMaxNumVridPerSystem 1.3.6.1.4.1.11.2.3.7.11.12.2.12.1.4
Indicates the maximum number of VRID per system.
OBJECT-TYPE    
  INTEGER  

snVrrpClearVrrpStat 1.3.6.1.4.1.11.2.3.7.11.12.2.12.1.5
Clear VRRP statistics command.
OBJECT-TYPE    
  INTEGER normal(0), clear(1)  

snVrrpIntf 1.3.6.1.4.1.11.2.3.7.11.12.2.12.2
OBJECT IDENTIFIER    

snVrrpIfTable 1.3.6.1.4.1.11.2.3.7.11.12.2.12.2.1
The VRRP Interface Table describes the interfaces from the viewpoint of VRRP.
OBJECT-TYPE    
  SEQUENCE OF  
    SnVrrpIfEntry

snVrrpIfEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.12.2.1.1
The VRRP Interface Entry describes one interface from the viewpoint of VRRP.
OBJECT-TYPE    
  SnVrrpIfEntry  

snVrrpIfPort 1.3.6.1.4.1.11.2.3.7.11.12.2.12.2.1.1.1
The IP port of this VRRP interface.
OBJECT-TYPE    
  INTEGER  

snVrrpIfAuthType 1.3.6.1.4.1.11.2.3.7.11.12.2.12.2.1.1.2
The authentication type of this interface.
OBJECT-TYPE    
  INTEGER noAuth(0), simpleTextPasswd(1), ipAuthHeader(2)  

snVrrpIfAuthPassword 1.3.6.1.4.1.11.2.3.7.11.12.2.12.2.1.1.3
The simple text password is allowed if only if the snVrrpIfAuthType type is simpleTextPasswd(1).
OBJECT-TYPE    
  OCTET STRING SIZE(0..8)  

snVrrpIfRxHeaderErrCnts 1.3.6.1.4.1.11.2.3.7.11.12.2.12.2.1.1.4
The received Header error counts in this interface.
OBJECT-TYPE    
  Counter  

snVrrpIfRxAuthTypeErrCnts 1.3.6.1.4.1.11.2.3.7.11.12.2.12.2.1.1.5
The received authentication type error counts in this interface.
OBJECT-TYPE    
  Counter  

snVrrpIfRxAuthPwdMismatchErrCnts 1.3.6.1.4.1.11.2.3.7.11.12.2.12.2.1.1.6
The received authentication password mismatched error counts in this interface.
OBJECT-TYPE    
  Counter  

snVrrpIfRxVridErrCnts 1.3.6.1.4.1.11.2.3.7.11.12.2.12.2.1.1.7
The received unfound VRID error counts in this interface.
OBJECT-TYPE    
  Counter  

snVrrpVirRtr 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3
OBJECT IDENTIFIER    

snVrrpVirRtrTable 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1
The VRRP virtual router Entry describes one virtual router from the viewpoint of VRRP.
OBJECT-TYPE    
  SEQUENCE OF  
    SnVrrpVirRtrEntry

snVrrpVirRtrEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1
The VRRP virtual router Entry describes one virtual router from the viewpoint of VRRP.
OBJECT-TYPE    
  SnVrrpVirRtrEntry  

snVrrpVirRtrPort 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.1
The IP port of this VRRP interface.
OBJECT-TYPE    
  INTEGER  

snVrrpVirRtrId 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.2
One of the virtual router ID of this VRRP interface.
OBJECT-TYPE    
  INTEGER 1..255  

snVrrpVirRtrOwnership 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.3
The ownership of this VRRP router interface can be set either owner(1) or backup(2). VirRtr SNMP-GET returns incomplete(0), it means no IP address has assigned to this VRRP router interface.
OBJECT-TYPE    
  INTEGER incomplete(0), owner(1), backup(2)  

snVrrpVirRtrCfgPriority 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.4
The higher the number the higher the priority is. This parameter decides which backup router should becomes the Active Router for the interface. A backup Router with higher priority selected to becomes the Active Router. Therefore, this Object can be set if only if snVrrpVirRtrOwnership is set to backup(2).
OBJECT-TYPE    
  INTEGER 3..254  

snVrrpVirRtrTrackPriority 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.5
The higher the number the higher the priority is. after this object is configured, the snVrrpVirRtrCurrPriority of this interface will be adjusted dynamically with this track priority when the Track Port states first changes from UP to DOWN.
OBJECT-TYPE    
  INTEGER 1..254  

snVrrpVirRtrCurrPriority 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.6
The higher the number the higher the priority is. This object will be adjusted dynamically with the track priority when the Track Port states first changes from UP to DOWN.
OBJECT-TYPE    
  INTEGER 1..254  

snVrrpVirRtrHelloInt 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.7
Time interval between advertisements (seconds).
OBJECT-TYPE    
  INTEGER 1..84  

snVrrpVirRtrDeadInt 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.8
Dead interval (seconds).
OBJECT-TYPE    
  INTEGER 0..84  

snVrrpVirRtrPreemptMode 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.9
This mode controls whether a higher priority Backup router preempts a lower priority Master. The mode with enabled(1) allow preemption and disabled(0) prohibit preemption.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snVrrpVirRtrState 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.10
This object specifies the VRRP Router's interface state as: init(0)...initialization state. master(1)...master state. backup(2)...backup state.
OBJECT-TYPE    
  INTEGER init(0), master(1), backup(2)  

snVrrpVirRtrActivate 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.11
This object specifies the VRRP Router's activate command as: disabled(0)...deactivate this VRRP Router. enabled(1)....activate this VRRP Router.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snVrrpVirRtrIpAddrMask 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.12
The numbers of IP Addresses of this virtual router of this interface.
OBJECT-TYPE    
  OCTET STRING SIZE(64)  

snVrrpVirRtrTrackPortMask 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.13
This object specifies the identity of the physical port whose state is to be monitored. Each bit is a port of the system. Default value is 0. VirRtr this object is configured then the Preference Level of this interface will be adjusted dynamically depending on the state of the Track Port. The interface's Preference Level is reduced by value of Preference Level parameter when the Track Port states first changes from UP to DOWN. When the Track Port next comes up the interface's Preference Level is increased by the amount specified by the Preference Level. The Chassis/Stackable router VRRP Track port membership. The size of the OCTET STRING for Chassis is 32. The size of the OCTET STRING for Stackable is 4.
OBJECT-TYPE    
  OCTET STRING SIZE(4..32)  

snVrrpVirRtrTrackVifMask 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.14
This object specifies the identity of the virtual interface whose state is to be monitored. Each bit is a port of the system. Default value is 0. VirRtr this object is configured then the Preference Level of this interface will be adjusted dynamically depending on the state of the Track Port. The interface's Preference Level is reduced by value of Preference Level parameter when the Track Port states first changes from UP to DOWN. When the Track Port next comes up the interface's Preference Level is increased by the amount specified by the Preference Level. The Chassis/Stackable router VRRP Track port membership The size of the OCTET STRING for Chassis is 8. The size of the OCTET STRING for Stackable is 4.
OBJECT-TYPE    
  OCTET STRING SIZE(4..8)  

snVrrpVirRtrRowStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.15
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an existing row VirRtr the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
OBJECT-TYPE    
  INTEGER invalid(1), valid(2), delete(3), create(4), modify(5)  

snVrrpVirRtrRxArpPktDropCnts 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.16
The received VRRP ARP Packet Drop Counts.
OBJECT-TYPE    
  Counter  

snVrrpVirRtrRxIpPktDropCnts 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.17
The received VRRP IP Packet Drop Counts.
OBJECT-TYPE    
  Counter  

snVrrpVirRtrRxPortMismatchCnts 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.18
The received VRRP Port mismatching Counts.
OBJECT-TYPE    
  Counter  

snVrrpVirRtrRxNumOfIpMismatchCnts 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.19
The received VRRP Number of IP Addresses mismatching Counts.
OBJECT-TYPE    
  Counter  

snVrrpVirRtrRxIpMismatchCnts 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.20
The received VRRP IP Address mismatching Counts.
OBJECT-TYPE    
  Counter  

snVrrpVirRtrRxHelloIntMismatchCnts 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.21
The counts of the virtual router interface with hello interval mismatch counts.
OBJECT-TYPE    
  Counter  

snVrrpVirRtrRxPriorityZeroFromMasterCnts 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.22
The counts of the virtual router interface with Priority zero from the master.
OBJECT-TYPE    
  Counter  

snVrrpVirRtrRxHigherPriorityCnts 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.23
The counts of the virtual router interface with higher Priority.
OBJECT-TYPE    
  Counter  

snVrrpVirRtrTransToMasterStateCnts 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.24
The counts of the virtual router interface transition to master state.
OBJECT-TYPE    
  Counter  

snVrrpVirRtrTransToBackupStateCnts 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.25
The counts of the virtual router interface transition to backup state.
OBJECT-TYPE    
  Counter  

snVrrpVirRtrCurrDeadInt 1.3.6.1.4.1.11.2.3.7.11.12.2.12.3.1.1.26
Current Dead interval (in 100 milliseconds).
OBJECT-TYPE    
  INTEGER  

snLoopbackIntfConfigTable 1.3.6.1.4.1.11.2.3.7.11.12.2.13.1
Loopback Interface Config table.
OBJECT-TYPE    
  SEQUENCE OF  
    SnLoopbackIntfConfigEntry

snLoopbackIntfConfigEntry 1.3.6.1.4.1.11.2.3.7.11.12.2.13.1.1
An entry in the Loopback Interface Config table.
OBJECT-TYPE    
  SnLoopbackIntfConfigEntry  

snLoopbackIntfConfigPortIndex 1.3.6.1.4.1.11.2.3.7.11.12.2.13.1.1.1
The port index for Loopback Interface config entry.
OBJECT-TYPE    
  INTEGER 1..8  

snLoopbackIntfMode 1.3.6.1.4.1.11.2.3.7.11.12.2.13.1.1.2
The Loopback Interface mode.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

snLoopbackIntfRowStatus 1.3.6.1.4.1.11.2.3.7.11.12.2.13.1.1.3
This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
OBJECT-TYPE    
  INTEGER invalid(1), valid(2), delete(3), create(4), modify(5)  

Defined Objects

DisplayString  
OCTET STRING    

RtrStatus  
INTEGER disabled(0), enabled(1)    

ClearStatus  
INTEGER normal(0), clear(1)    

RowSts  
INTEGER other(1), valid(2), delete(3), create(4)    

PortIndex  
INTEGER 1..3900    

Action  
INTEGER deny(0), permit(1)    

PhysAddress  
OCTET STRING    

Metric  
INTEGER 0..'FFFF'h    

PortMask  
INTEGER    

SnRtIpStaticRouteEntry  
SEQUENCE    
  INTEGER as snRtIpStaticRouteIndex  
  IpAddress as snRtIpStaticRouteDest  
  IpAddress as snRtIpStaticRouteMask  
  IpAddress as snRtIpStaticRouteNextHop  
  INTEGER as snRtIpStaticRouteMetric  
  RowSts as snRtIpStaticRouteRowStatus  
  INTEGER as snRtIpStaticRouteDistance  

SnRtIpFilterEntry  
SEQUENCE    
  INTEGER as snRtIpFilterIndex  
  INTEGER as snRtIpFilterAction  
  INTEGER as snRtIpFilterProtocol  
  IpAddress as snRtIpFilterSourceIp  
  IpAddress as snRtIpFilterSourceMask  
  IpAddress as snRtIpFilterDestIp  
  IpAddress as snRtIpFilterDestMask  
  INTEGER as snRtIpFilterOperator  
  INTEGER as snRtIpFilterOperand  
  RowSts as snRtIpFilterRowStatus  
  RtrStatus as snRtIpFilterEstablished  
  INTEGER as snRtIpFilterQosPriority  

SnRtIpRarpEntry  
SEQUENCE    
  INTEGER as snRtIpRarpIndex  
  OCTET STRING as snRtIpRarpMac  
  IpAddress as snRtIpRarpIp  
  RowSts as snRtIpRarpRowStatus  

SnRtStaticArpEntry  
SEQUENCE    
  INTEGER as snRtStaticArpIndex  
  IpAddress as snRtStaticArpIp  
  OCTET STRING as snRtStaticArpMac  
  PortIndex as snRtStaticArpPort  
  RowSts as snRtStaticArpRowStatus  

SnRtIpPortAddrEntry  
SEQUENCE    
  PortIndex as snRtIpPortAddrPortIndex  
  IpAddress as snRtIpPortAddress  
  IpAddress as snRtIpPortSubnetMask  
  INTEGER as snRtIpPortAddrType  
  RowSts as snRtIpPortRowStatus  

SnRtIpPortAccessEntry  
SEQUENCE    
  PortIndex as snRtIpPortAccessPortIndex  
  INTEGER as snRtIpPortAccessDirection  
  OCTET STRING as snRtIpPortAccessFilters  
  RowSts as snRtIpPortAccessRowStatus  

SnRtIpPortConfigEntry  
SEQUENCE    
  PortIndex as snRtIpPortConfigPortIndex  
  INTEGER as snRtIpPortMtu  
  INTEGER as snRtIpPortEncap  
  INTEGER as snRtIpPortMetric  
  RtrStatus as snRtIpPortDirBcastFwd  

SnRtUdpBcastFwdPortEntry  
SEQUENCE    
  INTEGER as snRtUdpBcastFwdPortIndex  
  INTEGER as snRtUdpBcastFwdPortNumber  
  RowSts as snRtUdpBcastFwdPortRowStatus  

SnRtUdpHelperEntry  
SEQUENCE    
  PortIndex as snRtUdpHelperPortIndex  
  INTEGER as snRtUdpHelperIndex  
  IpAddress as snRtUdpHelperAddr  
  RowSts as snRtUdpHelperRowStatus  

SnRtIpTraceRouteResultEntry  
SEQUENCE    
  INTEGER as snRtIpTraceRouteResultIndex  
  IpAddress as snRtIpTraceRouteResultAddr  
  TimeTicks as snRtIpTraceRouteResultRoundTripTime1  
  TimeTicks as snRtIpTraceRouteResultRoundTripTime2  

SnRtIpFwdCacheEntry  
SEQUENCE    
  INTEGER as snRtIpFwdCacheIndex  
  IpAddress as snRtIpFwdCacheIp  
  OCTET STRING as snRtIpFwdCacheMac  
  IpAddress as snRtIpFwdCacheNextHopIp  
  INTEGER as snRtIpFwdCacheOutgoingPort  
  INTEGER as snRtIpFwdCacheType  
  INTEGER as snRtIpFwdCacheAction  
  INTEGER as snRtIpFwdCacheFragCheck  
  INTEGER as snRtIpFwdCacheSnapHdr  
  INTEGER as snRtIpFwdCacheVLanId  

SnRtIpRipPortConfigEntry  
SEQUENCE    
  PortIndex as snRtIpRipPortConfigPortIndex  
  INTEGER as snRtIpRipPortVersion  
  RtrStatus as snRtIpRipPortPoisonReverse  
  INTEGER as snRtIpRipPortLearnDefault  

SnRtIpRipRedisEntry  
SEQUENCE    
  INTEGER as snRtIpRipRedisIndex  
  Action as snRtIpRipRedisAction  
  INTEGER as snRtIpRipRedisProtocol  
  IpAddress as snRtIpRipRedisIp  
  IpAddress as snRtIpRipRedisMask  
  Metric as snRtIpRipRedisMatchMetric  
  INTEGER as snRtIpRipRedisSetMetric  
  RowSts as snRtIpRipRedisRowStatus  

SnRtIpRipRouteFilterEntry  
SEQUENCE    
  INTEGER as snRtIpRipRouteFilterId  
  Action as snRtIpRipRouteFilterAction  
  IpAddress as snRtIpRipRouteFilterIpAddr  
  IpAddress as snRtIpRipRouteFilterSubnetMask  
  INTEGER as snRtIpRipRouteFilterRowStatus  

SnRtIpRipNbrFilterEntry  
SEQUENCE    
  INTEGER as snRtIpRipNbrFilterId  
  Action as snRtIpRipNbrFilterAction  
  IpAddress as snRtIpRipNbrFilterSourceIp  
  INTEGER as snRtIpRipNbrFilterRowStatus  

SnRtIpRipPortAccessEntry  
SEQUENCE    
  PortIndex as snRtIpRipPortAccessPort  
  INTEGER as snRtIpRipPortAccessDir  
  OCTET STRING as snRtIpRipPortAccessFilterList  
  INTEGER as snRtIpRipPortAccessRowStatus  

SnDvmrpVInterfaceEntry  
SEQUENCE    
  INTEGER as snDvmrpVInterfaceVifIndex  
  INTEGER as snDvmrpVInterfaceType  
  INTEGER as snDvmrpVInterfaceOperState  
  IpAddress as snDvmrpVInterfaceLocalAddress  
  IpAddress as snDvmrpVInterfaceRemoteAddress  
  IpAddress as snDvmrpVInterfaceRemoteSubnetMask  
  INTEGER as snDvmrpVInterfaceMetric  
  INTEGER as snDvmrpVInterfaceTtlThreshold  
  RtrStatus as snDvmrpVInterfaceAdvertiseLocal  
  RtrStatus as snDvmrpVInterfaceEncapsulation  
  INTEGER as snDvmrpVInterfaceStatus  

SnDvmrpNeighborEntry  
SEQUENCE    
  INTEGER as snDvmrpNeighborEntryIndex  
  INTEGER as snDvmrpNeighborVifIndex  
  IpAddress as snDvmrpNeighborAddress  
  TimeTicks as snDvmrpNeighborUpTime  
  TimeTicks as snDvmrpNeighborExpiryTime  
  INTEGER as snDvmrpNeighborGenerationId  
  INTEGER as snDvmrpNeighborMajorVersion  
  INTEGER as snDvmrpNeighborMinorVersion  
  INTEGER as snDvmrpNeighborCapabilities  

SnDvmrpRouteEntry  
SEQUENCE    
  INTEGER as snDvmrpRouteEntryIndex  
  IpAddress as snDvmrpRouteSource  
  IpAddress as snDvmrpRouteSourceMask  
  IpAddress as snDvmrpRouteUpstreamNeighbor  
  INTEGER as snDvmrpRouteVifIndex  
  INTEGER as snDvmrpRouteMetric  
  TimeTicks as snDvmrpRouteExpiryTime  

SnDvmrpRouteNextHopEntry  
SEQUENCE    
  IpAddress as snDvmrpRouteNextHopSource  
  IpAddress as snDvmrpRouteNextHopSourceMask  
  INTEGER as snDvmrpRouteNextHopVifIndex  
  INTEGER as snDvmrpRouteNextHopType  

SnDvmrpVIfStatEntry  
SEQUENCE    
  INTEGER as snDvmrpVIfStatVifIndex  
  Counter as snDvmrpVIfStatInPkts  
  Counter as snDvmrpVIfStatOutPkts  
  Counter as snDvmrpVIfStatInOctets  
  Counter as snDvmrpVIfStatOutOctets  
  Counter as snDvmrpVIfStatInProbePkts  
  Counter as snDvmrpVIfStatOutProbePkts  
  Counter as snDvmrpVIfStatDiscardProbePkts  
  Counter as snDvmrpVIfStatInRtUpdatePkts  
  Counter as snDvmrpVIfStatOutRtUpdatePkts  
  Counter as snDvmrpVIfStatDiscardRtUpdatePkts  
  Counter as snDvmrpVIfStatInGraftPkts  
  Counter as snDvmrpVIfStatOutGraftPkts  
  Counter as snDvmrpVIfStatDiscardGraftPkts  
  Counter as snDvmrpVIfStatInGraftAckPkts  
  Counter as snDvmrpVIfStatOutGraftAckPkts  
  Counter as snDvmrpVIfStatDiscardGraftAckPkts  
  Counter as snDvmrpVIfStatInPrunePkts  
  Counter as snDvmrpVIfStatOutPrunePkts  
  Counter as snDvmrpVIfStatDiscardPrunePkts  

SnFsrpIfEntry  
SEQUENCE    
  INTEGER as snFsrpIfPort  
  IpAddress as snFsrpIfIpAddress  
  IpAddress as snFsrpIfVirRtrIpAddr  
  IpAddress as snFsrpIfOtherRtrIpAddr  
  INTEGER as snFsrpIfPreferLevel  
  PortMask as snFsrpIfTrackPortMask  
  INTEGER as snFsrpIfRowStatus  
  INTEGER as snFsrpIfState  
  INTEGER as snFsrpIfKeepAliveTime  
  INTEGER as snFsrpIfRouterDeadTime  
  OCTET STRING as snFsrpIfChassisTrackPortMask  

SnPimVInterfaceEntry  
SEQUENCE    
  INTEGER as snPimVInterfaceVifIndex  
  INTEGER as snPimVInterfaceType  
  IpAddress as snPimVInterfaceLocalAddress  
  IpAddress as snPimVInterfaceLocalSubnetMask  
  IpAddress as snPimVInterfaceRemoteAddress  
  IpAddress as snPimVInterfaceDR  
  INTEGER as snPimVInterfaceTtlThreshold  
  INTEGER as snPimVInterfaceStatus  

SnPimNeighborEntry  
SEQUENCE    
  INTEGER as snPimNeighborEntryIndex  
  INTEGER as snPimNeighborVifIndex  
  IpAddress as snPimNeighborAddress  
  TimeTicks as snPimNeighborUpTime  
  TimeTicks as snPimNeighborExpiryTime  

SnPimVIfStatEntry  
SEQUENCE    
  INTEGER as snPimVIfStatVifIndex  
  Counter as snPimVIfStatInJoinPkts  
  Counter as snPimVIfStatOutJoinPkts  
  Counter as snPimVIfStatDiscardJoinPkts  
  Counter as snPimVIfStatInPrunePkts  
  Counter as snPimVIfStatOutPrunePkts  
  Counter as snPimVIfStatDiscardPrunePkts  
  Counter as snPimVIfStatInAssertPkts  
  Counter as snPimVIfStatOutAssertPkts  
  Counter as snPimVIfStatDiscardAssertPkts  
  Counter as snPimVIfStatInHelloPkts  
  Counter as snPimVIfStatOutHelloPkts  
  Counter as snPimVIfStatDiscardHelloPkts  
  Counter as snPimVIfStatInGraftPkts  
  Counter as snPimVIfStatOutGraftPkts  
  Counter as snPimVIfStatDiscardGraftPkts  
  Counter as snPimVIfStatInGraftAckPkts  
  Counter as snPimVIfStatOutGraftAckPkts  
  Counter as snPimVIfStatDiscardGraftAckPkts  

SnVrrpIfEntry  
SEQUENCE    
  INTEGER as snVrrpIfPort  
  INTEGER as snVrrpIfAuthType  
  OCTET STRING as snVrrpIfAuthPassword  
  Counter as snVrrpIfRxHeaderErrCnts  
  Counter as snVrrpIfRxAuthTypeErrCnts  
  Counter as snVrrpIfRxAuthPwdMismatchErrCnts  
  Counter as snVrrpIfRxVridErrCnts  

SnVrrpVirRtrEntry  
SEQUENCE    
  INTEGER as snVrrpVirRtrPort  
  INTEGER as snVrrpVirRtrId  
  INTEGER as snVrrpVirRtrOwnership  
  INTEGER as snVrrpVirRtrCfgPriority  
  INTEGER as snVrrpVirRtrTrackPriority  
  INTEGER as snVrrpVirRtrCurrPriority  
  INTEGER as snVrrpVirRtrHelloInt  
  INTEGER as snVrrpVirRtrDeadInt  
  INTEGER as snVrrpVirRtrPreemptMode  
  INTEGER as snVrrpVirRtrState  
  INTEGER as snVrrpVirRtrActivate  
  OCTET STRING as snVrrpVirRtrIpAddrMask  
  OCTET STRING as snVrrpVirRtrTrackPortMask  
  OCTET STRING as snVrrpVirRtrTrackVifMask  
  INTEGER as snVrrpVirRtrRowStatus  
  Counter as snVrrpVirRtrRxArpPktDropCnts  
  Counter as snVrrpVirRtrRxIpPktDropCnts  
  Counter as snVrrpVirRtrRxPortMismatchCnts  
  Counter as snVrrpVirRtrRxNumOfIpMismatchCnts  
  Counter as snVrrpVirRtrRxIpMismatchCnts  
  Counter as snVrrpVirRtrRxHelloIntMismatchCnts  
  Counter as snVrrpVirRtrRxPriorityZeroFromMasterCnts  
  Counter as snVrrpVirRtrRxHigherPriorityCnts  
  Counter as snVrrpVirRtrTransToMasterStateCnts  
  Counter as snVrrpVirRtrTransToBackupStateCnts  
  INTEGER as snVrrpVirRtrCurrDeadInt  

SnLoopbackIntfConfigEntry  
SEQUENCE    
  INTEGER as snLoopbackIntfConfigPortIndex  
  INTEGER as snLoopbackIntfMode  
  INTEGER as snLoopbackIntfRowStatus