
| RFC1155-SMI | RFC-1212 | HP-SN-ROOT-MIB |
| Counter | TimeTicks | IpAddress |
| Gauge | OBJECT-TYPE | snSwitch |
| snSwInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1 | ||
| OBJECT IDENTIFIER | |||
| snSwGroupOperMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.1 | ||
| noVLan(1) represents all switch ports with no virtual LAN by port (no Port VLAN), and with no tag assigned. vlanByPort(2) represents all switch ports with Basic VLAN (layer2 Switch). | |||
| OBJECT-TYPE | |||
| INTEGER | noVLan(1), vlanByPort(2) | ||
| snSwGroupIpL3SwMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.2 | ||
| The Switch Group is configured with the Layer3 IP Switch mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate Layer3 IP Switch disabled(0)..........disable Layer3 IP Switch | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snSwGroupIpMcastMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.3 | ||
| The Switch Group is configured with the IP Multicast pruning mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate IP Multicast pruning disabled(0)..........no IP Multicast pruning | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snSwGroupDefaultCfgMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.4 | ||
| The Switch Group is configured with the Default configuration. If the default configuration gets overwritten, the state will change to non-default. default(1)...........default configuration nonDefault(2)..........non default configuration | |||
| OBJECT-TYPE | |||
| INTEGER | default(1), nonDefault(2) | ||
| snSwGroupSwitchAgeTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.5 | ||
| The Switch Age time is 180sec by default. The configured range is 10 to 10,000sec. The time represents the time span to age out an MAC Address entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snVLanGroupVlanCurEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.6 | ||
| The current total entry number of VLANs are configured. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snVLanGroupSetAllVLan | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.7 | ||
| The value of this object is the VLanIndex of a particalur entry in snVLanByPortTable (snVLanByPortVLanIndex). All the attributes of that row of table except PortMask will be used to set the same attributes for the entire VLan group. VLanId and PortMask must be set for that particular entry prior to setting this object. Switch software will base on that VLAN information to set the entire VLAN. Note: All the intended attributes of the given row of the table (given VLAN) must be set prior setting this object. When this object is set, Set-All-VLAN action will take place simultaneously. The previous setting will be overwritten by the new one. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwPortSetAll | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.8 | ||
| The value of this object is the index number of the snSwPortInfoTable (snSwPortInfoPortIndex). snSwPortInfoMonitorMode, snSwPortInfoTagType, snSwPortInfoChnMode, snSwPortInfoSpeed, snSwPortInfoAdminStatus are all the read-write attributes of that row of table. They will be used to set the same attributes for all the ports in the system. Note: prior setting this object, all the intended attributes of the given row of the table must be set. Otherwise, the current data of the row will be used to set the entire port-table. The previous setting will be overwritten by the new one. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snFdbTableCurEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.9 | ||
| The current total entry number of FDB are configured. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snFdbTableStationFlush | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.10 | ||
| The following values of the flush state can only be read: normal(1)... normal state error(2)... operation failed flushing(4)... in process The following value can be written: flush(3).....do flush The agent will return a response even before the flush is done. And the read value will be flushing until flush is done. And the flush request will be rejected until error or normal. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), error(2), flush(3), flushing(4) | ||
| snPortStpSetAll | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.11 | ||
| The value of this object is 1 which means invoking Port STP Set-all command. The snPortStpPriority, snPortStpPathCost, the read-write STP related attributes of the first row of table will be used to set the same attributes for all the ports in the system. Note: prior setting this object, all the intended attributes of the given row of the table must be set. Otherwise, the current data of the row will be used to set the entire port-table. The previous setting will be overwritten by the new one. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwProbePortNum | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.12 | ||
| A chassis switch probe port is operated as a traffic analyzer port and only one port can be assigned in the chassis. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number. A stackable switch is only assigned with one probe port as a traffic analyzer. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSw8021qTagMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.13 | ||
| The Switch Group is configured with the IEEE802.1q Tagging mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate IEEE802.1q Tagging mode. disabled(0)..........no IEEE802.1q Tagging. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snSwGlobalStpMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.14 | ||
| Spanning Tree System Global Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Spanning Tree disabled(0)..........no Spanning Tree | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snSwIpMcastQuerierMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.15 | ||
| The IP Multicast pruning mode is configured either Non-Querier or Querier mode and the default is querier mode. querier(1)...........when prunning traffic locally within the VLAN. nonQuerier(2)........when running with a multicast capable router in the network. | |||
| OBJECT-TYPE | |||
| INTEGER | querier(1), nonQuerier(2) | ||
| snSwViolatorPortNumber | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.17 | ||
| The port number of the switch or router that received a violator packet. It is included in the locked address violation trap. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only). | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwViolatorMacAddress | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.18 | ||
| The source address of the violator packet received by the switch or router. It is included in the locked address violation trap. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| snVLanGroupVlanMaxEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.19 | ||
| The maximum number of VLAN entries are allowed to configure. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwEosBufferSize | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.20 | ||
| A specific buffer size for all the different EOS buffers. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snVLanByPortEntrySize | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.21 | ||
| The size of each VLAN table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwPortEntrySize | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.22 | ||
| The size of each port table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snFdbStationEntrySize | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.23 | ||
| The size of each Fdb station table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snPortStpEntrySize | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.24 | ||
| The size of each port stp table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwEnableBridgeNewRootTrap | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.25 | ||
| Indicates whether the SNMP agent process is permitted to generate bridge new root traps. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snSwEnableBridgeTopoChangeTrap | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.26 | ||
| Indicates whether the SNMP agent process is permitted to generate bridge topology change traps. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snSwEnableLockedAddrViolationTrap | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.27 | ||
| Indicates whether the SNMP agent process is permitted to generate locked address violation traps. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snSwIpxL3SwMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.28 | ||
| The Switch Group is configured with the Layer3 IPX Switch mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate Layer3 Switch disabled(0)..........disable Layer3 Switch | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snVLanByIpSubnetMaxSubnets | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.29 | ||
| The maximum number of subnets for each IP VLAN. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snVLanByIpxNetMaxNetworks | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.30 | ||
| The maximum number of networks for each IPX VLAN. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwProtocolVLanMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.31 | ||
| disabled(0) - represents system with Protocol VLAN disabled. enabled(1) - represents system with Protocol VLAN enabled (Layer3 VLAN). | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snMacStationVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.32 | ||
| This MAC Station VLAN ID index to the standard Forwarding Database for Transparent Bridge Table. (dot1dTpFdbTable). Since the dot1dTpFdbTable index is the MAC Address assigned to one of the ports in the bridge(VLAN) and each MAC address can be re-assigned to a different ports belonging to different bridges(VLANs), the snMacStationVLanId can be used by users to specify which bridge(VLAN) MAC Station information of the dot1dTpFdbTable users want to retrieve. If users do not specify the VLan ID in this MIB, the default VLAN (bridge) ID will be used when dot1dTpFdbTable is retrieved. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..4095 | ||
| snSwClearCounters | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.33 | ||
| valid(0) - a SNMP-GET of this mib shows that it is valid command to use. clear(1) - represents clear counter command of the following counters: Dot3, MIB2, IP and IPX counters for all ports. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(0), clear(1) | ||
| snSw8021qTagType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.34 | ||
| The IEEE802.1q tag type embedded in the length/type field of an Ethernet packet. It specifies that the 2 octets after the length/type field in an Ethernet packet is the tag value. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwBroadcastLimit | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.35 | ||
| Limit the number of broadcast packets to forward out of the switch ports. This object specifies the number of broadcast packets per second. Setting a value of 0 to this object disables the limitation check. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwMaxMacFilterPerSystem | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.36 | ||
| The maximum number of MAC Filters per system in the MAC Filter table. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwMaxMacFilterPerPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.37 | ||
| The maximum number of MAC Filters per port in the Port MAC Access Filter table. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwDefaultVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.38 | ||
| The VLAN ID of the DEFAULT PORT-VLAN. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..4095 | ||
| snSwGlobalAutoNegotiate | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.39 | ||
| This feature only applies to Gigabit Ethernet ports. If set to disable(0), all Gigabit Ethernet ports will be put to non- negotiation mode. If set to enable(1), all Gigabit Ethernet ports will start auto-negotiation indefinitely until succeed. If set to negFullAuto(2), all Gigabit Ethernet ports will start with auto-negotiation, if the negotiation failed, then they will automatically switch to non-negotiation mode. Stackable products (except TurboIron 8) Gigabit Ethernet ports do not support negFullAuto(2). If the snSwPortInfoAutoNegotiate value of a port was not set to global, this global value does not apply to the negotiation mode of that port. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1), negFullAuto(2), other(3) | ||
| snSwQosMechanism | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.40 | ||
| Indicates whether the qos mechanism is strict or weighted. | |||
| OBJECT-TYPE | |||
| INTEGER | strict(0), weighted(1) | ||
| snSwSingleStpMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.41 | ||
| Single Spanning Tree System Mode in the Switch Group can be set either enabled or disabled and the default is disabled mode. enabled(1)...........activate Single Spanning Tree disabled(0)..........no Single Spanning Tree | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snSwFastStpMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.42 | ||
| Fast Spanning Tree System Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Fast Spanning Tree disabled(0)..........no Fast Spanning Tree | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snVLanInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2 | ||
| OBJECT IDENTIFIER | |||
| snVLanByPortTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1 | ||
| If snSwGroupOperMode is configured as basic mode which is VLAN by Port, Layer2 switching, then this table is valid. Each VLAN switch port could have a number of VLAN IDs. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnVLanByPortEntry | |||
| snVLanByPortEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1 | ||
| An entry in the VLAN By Port Information table. snVLanByPortVLanIndex = 1 and with snVLanByPortVLanId = 1 together implies all attributes applying to the Global switch group i.e. noVLan. A SNMP SET PDU for a row of the snVLanByPortTable requires the entired sequence of the MIB Objects in each snVLanByPortEntry stored in one PDU. Otherwise, GENERR return-value will be returned. | |||
| OBJECT-TYPE | |||
| SnVLanByPortEntry | |||
| snVLanByPortVLanIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.1 | ||
| The VLAN ID index must not be greater than the snVLanGroupVlanMaxEntry. Each VLAN Identifier can have a membership of multiple ports. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..4095 | ||
| snVLanByPortVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.2 | ||
| The VLAN ID index to the VLAN By Port Info Table. Each VLAN Identifier can have a membership of multiple ports. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..4095 | ||
| snVLanByPortPortMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.3 | ||
| The Standand-alone switch VLAN port membership. (It is obsoleted for Chassis Product) | |||
| OBJECT-TYPE | |||
| PortMask | |||
| snVLanByPortQos | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.4 | ||
| The Stand alone stackable switch VLAN Priority values are: low(0) -- low prority high(1) -- high prority. The BigIron switch VLAN Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7) | |||
| OBJECT-TYPE | |||
| INTEGER | level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7) | ||
| snVLanByPortStpMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.5 | ||
| Spanning Tree Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Spanning Tree disabled(0)..........no Spanning Tree | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snVLanByPortStpPriority | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.6 | ||
| dot1dStpPriority : The value of the write-able portion of the Stp ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of the base bridge address - dot1dBaseBridgeAddress. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| snVLanByPortStpGroupMaxAge | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.7 | ||
| dot1dStpBridgeMaxAge: From RFC1493(Bridge MIB). The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds. | |||
| OBJECT-TYPE | |||
| INTEGER | 6..40 | ||
| snVLanByPortStpGroupHelloTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.8 | ||
| dot1dStpBridgeHelloTime: From RFC1493(Bridge MIB). The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..10 | ||
| snVLanByPortStpGroupForwardDelay | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.9 | ||
| dot1dStpBridgeForwardDelay : From RFC1493(Bridge MIB). The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds. | |||
| OBJECT-TYPE | |||
| INTEGER | 4..30 | ||
| snVLanByPortRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.10 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), valid(2), delete(3), create(4), modify(5) | ||
| snVLanByPortOperState | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.11 | ||
| By default, this mode is set to notActivated(0). notActivated(0)...the VLAN entry is not activated and not in running mode. activated(1)......the VLAN entry is activated and in running mode | |||
| OBJECT-TYPE | |||
| INTEGER | notActivated(0), activated(1) | ||
| snVLanByPortBaseNumPorts | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.12 | ||
| The number of ports controlled by this bridging entity. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snVLanByPortBaseType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.13 | ||
| Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), transparent-only(2), sourceroute-only(3), srt(4) | ||
| snVLanByPortStpProtocolSpecification | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.14 | ||
| An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), decLb100(2), ieee8021d(3) | ||
| snVLanByPortStpMaxAge | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.15 | ||
| dot1dStpMaxAge: From RFC1493(Bridge MIB). The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using. | |||
| OBJECT-TYPE | |||
| Timeout | |||
| snVLanByPortStpHelloTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.16 | ||
| dot1dStpHelloTime: From RFC1493(Bridge MIB). The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using. | |||
| OBJECT-TYPE | |||
| Timeout | |||
| snVLanByPortStpHoldTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.17 | ||
| dot1dStpHoldTime: From RFC1493(Bridge MIB). This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snVLanByPortStpForwardDelay | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.18 | ||
| dot1dStpForwardDelay: From RFC1493(Bridge MIB). This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.] | |||
| OBJECT-TYPE | |||
| Timeout | |||
| snVLanByPortStpTimeSinceTopologyChange | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.19 | ||
| The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| snVLanByPortStpTopChanges | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.20 | ||
| The total number of topology changes detected by this bridge since the management entity was last reset or initialized. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snVLanByPortStpRootCost | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.21 | ||
| dot1dStpRootCost: From RFC1493(Bridge MIB). The cost of the path to the root as seen from this bridge. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snVLanByPortStpRootPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.22 | ||
| dot1dStpRootPort: From RFC1493(Bridge MIB). The port number of the port which offers the lowest cost path from this bridge to the root bridge. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snVLanByPortStpDesignatedRoot | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.23 | ||
| dot1dStpDesignatedRoot: From RFC1493(Bridge MIB). The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node. | |||
| OBJECT-TYPE | |||
| BridgeId | |||
| snVLanByPortBaseBridgeAddress | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.24 | ||
| The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with dot1dStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| snVLanByPortVLanName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.25 | ||
| VLAN Community Name string. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| snVLanByPortRouterIntf | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.26 | ||
| Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..60 | ||
| snVLanByPortChassisPortMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.27 | ||
| The Chassis VLAN switch port membership. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(32) | ||
| snVLanByProtocolTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2 | ||
| . | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnVLanByProtocolEntry | |||
| snVLanByProtocolEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1 | ||
| An entry in the VLAN By Protocol Configuration table. | |||
| OBJECT-TYPE | |||
| SnVLanByProtocolEntry | |||
| snVLanByProtocolVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.1 | ||
| The VLAN ID index to both of the VLAN By Port Info Table and this table. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..4095 | ||
| snVLanByProtocolIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.2 | ||
| The following IP/IPX protocol VLAN types are operated in Layer3 VLAN such as : ip(1), ipx(2) The following are operated in Layer2 bridging such as: appleTalk(3), decNet(4), netBios(5), others(6) -- other protocols which are defined here. | |||
| OBJECT-TYPE | |||
| INTEGER | ip(1), ipx(2), appleTalk(3), decNet(4), netBios(5), others(6) | ||
| snVLanByProtocolDynamic | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.3 | ||
| disabled(0) : disabled dynamic port inclusion - applied to switch only. enabled(1) : enabled dynamic port inclusion - applied to switch only. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snVLanByProtocolStaticMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.4 | ||
| The Standand-alone switch Protocol VLAN port membership applied in static mode. (It is obsoleted for Chassis Product) | |||
| OBJECT-TYPE | |||
| PortMask | |||
| snVLanByProtocolExcludeMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.5 | ||
| The Standand-alone switch Protocol VLAN port membership applied in exclusive mode. (It is obsoleted for Chassis Product) | |||
| OBJECT-TYPE | |||
| PortMask | |||
| snVLanByProtocolRouterIntf | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.6 | ||
| Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..60 | ||
| snVLanByProtocolRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.7 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), valid(2), delete(3), create(4), modify(5) | ||
| snVLanByProtocolDynamicMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.8 | ||
| The Standand-alone switch Protocol VLAN active port membership. (It is obsoleted for Chassis Product) | |||
| OBJECT-TYPE | |||
| PortMask | |||
| snVLanByProtocolChassisStaticMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.9 | ||
| The Chassis Protocol VLAN port membership applied in static mode. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(32) | ||
| snVLanByProtocolChassisExcludeMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.10 | ||
| The Chassis Protocol VLAN port membership applied in exclusive mode. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(32) | ||
| snVLanByProtocolChassisDynamicMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.11 | ||
| The Chassis Protocol VLAN active port membership. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(32) | ||
| snVLanByProtocolVLanName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.12 | ||
| VLAN Community Name string. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| snVLanByIpSubnetTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3 | ||
| An entry of the VLAN By IPX Network Number Table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnVLanByIpSubnetEntry | |||
| snVLanByIpSubnetEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1 | ||
| An entry in the VLAN By IP Subnet Configuration table. | |||
| OBJECT-TYPE | |||
| SnVLanByIpSubnetEntry | |||
| snVLanByIpSubnetVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.1 | ||
| The VLAN ID index to both of the VLAN By Port Info Table and this table. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..4095 | ||
| snVLanByIpSubnetIpAddress | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.2 | ||
| Subnet IP address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snVLanByIpSubnetSubnetMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.3 | ||
| Subnet mask associated with the Subnet IP address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snVLanByIpSubnetDynamic | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.4 | ||
| disabled(0) : disabled dynamic port inclusion - applied to switch only. enabled(1) : enabled dynamic port inclusion - applied to switch only. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snVLanByIpSubnetStaticMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.5 | ||
| The Standand-alone switch VLAN By Subnet port membership applied in static mode. (It is obsoleted for Chassis Product) | |||
| OBJECT-TYPE | |||
| PortMask | |||
| snVLanByIpSubnetExcludeMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.6 | ||
| The Standand-alone switch VLAN By Subnet port membership applied in exclusive mode. (It is obsoleted for Chassis Product) | |||
| OBJECT-TYPE | |||
| PortMask | |||
| snVLanByIpSubnetRouterIntf | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.7 | ||
| Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..60 | ||
| snVLanByIpSubnetRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.8 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), valid(2), delete(3), create(4), modify(5) | ||
| snVLanByIpSubnetDynamicMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.9 | ||
| The Standand-alone switch VLAN By Subnet active port membership. (It is obsoleted for Chassis Product) | |||
| OBJECT-TYPE | |||
| PortMask | |||
| snVLanByIpSubnetChassisStaticMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.10 | ||
| The Chassis VLAN By Subnet port membership applied in static mode. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(32) | ||
| snVLanByIpSubnetChassisExcludeMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.11 | ||
| The Chassis VLAN By Subnet port membership applied in exclusive mode. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(32) | ||
| snVLanByIpSubnetChassisDynamicMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.12 | ||
| The Chassis VLAN By Subnet active port membership. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(32) | ||
| snVLanByIpSubnetVLanName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.13 | ||
| VLAN Community Name string. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| snVLanByIpxNetTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4 | ||
| An entry of the VLAN By IPX Network Number Table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnVLanByIpxNetEntry | |||
| snVLanByIpxNetEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1 | ||
| An entry in the VLAN By Ipx Network Number Configuration table. | |||
| OBJECT-TYPE | |||
| SnVLanByIpxNetEntry | |||
| snVLanByIpxNetVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.1 | ||
| The VLAN ID index to both of the VLAN By Port Info Table and this table. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..4095 | ||
| snVLanByIpxNetNetworkNum | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.2 | ||
| IPX Network Number. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| snVLanByIpxNetFrameType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.3 | ||
| The following IPX Frame types are operated in Layer3 VLAN such as : ipxEthernet8022(1), ipxEthernet8023(2), ipxEthernetII(3), ipxEthernetSnap(4). choose notApplicable(0) for other protocols. Note: Each Network Number can be assigned with one unique Frame type; Otherwise, a SNMP-SET error will be returned. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(0), ipxEthernet8022(1), ipxEthernet8023(2), ipxEthernetII(3), ipxEthernetSnap(4) | ||
| snVLanByIpxNetDynamic | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.4 | ||
| disabled(0) : disabled dynamic port inclusion - applied to switch only. enabled(1) : enabled dynamic port inclusion - applied to switch only. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snVLanByIpxNetStaticMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.5 | ||
| The VLAN By IPX network port membership applied in static mode. | |||
| OBJECT-TYPE | |||
| PortMask | |||
| snVLanByIpxNetExcludeMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.6 | ||
| The VLAN By IPX network port membership applied in exclusive mode. | |||
| OBJECT-TYPE | |||
| PortMask | |||
| snVLanByIpxNetRouterIntf | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.7 | ||
| Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..60 | ||
| snVLanByIpxNetRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.8 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), valid(2), delete(3), create(4), modify(5) | ||
| snVLanByIpxNetDynamicMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.9 | ||
| The VLAN By IPX network active port membership. | |||
| OBJECT-TYPE | |||
| PortMask | |||
| snVLanByIpxNetChassisStaticMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.10 | ||
| The Chassis VLAN By IPX network port membership applied in static mode. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(32) | ||
| snVLanByIpxNetChassisExcludeMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.11 | ||
| The Chassis VLAN By IPX network port membership applied in exclusive mode. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(32) | ||
| snVLanByIpxNetChassisDynamicMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.12 | ||
| The Chassis VLAN By IPX network active port membership. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(32) | ||
| snVLanByIpxNetVLanName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.13 | ||
| VLAN Community Name string. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| snVLanByATCableTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5 | ||
| A Table Of VLAN By AppleTalk Network Number. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnVLanByATCableEntry | |||
| snVLanByATCableEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1 | ||
| An entry of the AppleTalk Cable VLAN table. | |||
| OBJECT-TYPE | |||
| SnVLanByATCableEntry | |||
| snVLanByATCableVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.1 | ||
| The VLAN ID of a PORT VLAN of which the AppleTalk Cable VLAN was attaching to. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..4095 | ||
| snVLanByATCableIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.2 | ||
| AppleTalk Cable VLAN index number. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snVLanByATCableRouterIntf | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.3 | ||
| A virtual router interface to the AppleTalk Cable VLAN, only router products accept the SNMP-SET operation. The value zero indicates that virtual router interface was not configured. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..60 | ||
| snVLanByATCableRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.4 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), valid(2), delete(3), create(4), modify(5) | ||
| snVLanByATCableChassisStaticMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.5 | ||
| A list of ports which are statically configured to become port members of a VLAN. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(32) | ||
| snVLanByATCableVLanName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.6 | ||
| VLAN Name string. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| snSwPortInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3 | ||
| OBJECT IDENTIFIER | |||
| snSwPortInfoTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1 | ||
| A specific snSwPortInfo group consists of a number of switch ports. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnSwPortInfoEntry | |||
| snSwPortInfoEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1 | ||
| An entry in the snSwPortInfo table indicates the configuration on a specified port. A SNMP SET PDU for a row of the snSwPortInfoTable requires the entired sequence of the MIB Objects in each snSwPortInfoEntry stored in one PDU. Otherwise, GENERR return-value will be returned. | |||
| OBJECT-TYPE | |||
| SnSwPortInfoEntry | |||
| snSwPortInfoPortNum | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.1 | ||
| The port index. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only). | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwPortInfoMonitorMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.2 | ||
| A monitoring port is selected and its traffic will be analyzed if the mode is not disabled(0), which is the default mode. The values are: disabled(0) -- No traffic monitoring input(1) -- traffic monitoring is activated on packets received output(2) -- traffic monitoring is activated on packets transmitted both(3) -- traffic monitoring is activated on packets received and transmitted. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), input(1), output(2), both(3) | ||
| snSwPortInfoTagType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.3 | ||
| For tagged port, we could have multiple VLANs per port. For untagged port or auto port, there is only one VLAN ID per port. | |||
| OBJECT-TYPE | |||
| INTEGER | tagged(1), untagged(2), auto(3), disabled(4) | ||
| snSwPortInfoChnMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.4 | ||
| The port can be configured to operate in either half or full duplex mode. The values are: halfDuplex(1)...half duplex mode fullDuplex(2)...full duplex mode The read-back channel status from hardware are: none(0).........link down or port disabled. halfDuplex(1)...half duplex mode fullDuplex(2)...full duplex mode The port media type (expansion or regular) and port link type (trunk or feeder) determine value of this object. The port can not set to half duplex mode if the port connect mode is m200e(4). However, the value of this parameter may be automatically set whenever the expansion port is connected (e.g. cascade connecting device). | |||
| OBJECT-TYPE | |||
| INTEGER | none(0), halfDuplex(1), fullDuplex(2) | ||
| snSwPortInfoSpeed | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.5 | ||
| The speed configuration for a port. The values are: none(0)..........link down or no traffic. sAutoSense(1)....Auto-sensing 10 or 100Mbits. s10M(2)..........10Mbits per second. s100M(3).........100Mbits per second. s1G(4)...........1Gbits per second. s45M(5)..........45Mbits per second (T3) (for expansion board only). s155M(6).........155Mbits per second (ATM) (for expansion board only). The read-back hardware status are the following: none(0)..........link down or no traffic. s10M(2)..........10Mbits per second. s100M(3).........100Mbits per second. s1G(4)...........1Gbits per second. s45M(5)..........45Mbits per second (T3) (for expansion board only). s155M(6).........155Mbits per second (ATM) (for expansion board only). The port media type (expansion or regular) and port link type (trunk or feeder) determine whether this object can be written and the valid values. It is not allowed to change speed for trunks ports. For expansion ports, all of the above speed can be set. However, the value of this parameter may be automatically set whenever the expansion port is connected (e.g. cascade connecting device). | |||
| OBJECT-TYPE | |||
| INTEGER | none(0), sAutoSense(1), s10M(2), s100M(3), s1G(4), s45M(5), s155M(6) | ||
| snSwPortInfoMediaType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.6 | ||
| The media type for the port. The values are: other(1).........other or unknown media. m100BaseTX(2)....100Mbits per second copper. m100BaseFX(3)....100Mbits per second fiber. m1000BaseFX(4)...1Gbits per second fiber. mT3(5)...........45Mbits per second (T3). m155ATM(6).......155Mbits per second (ATM). m1000BaseTX(7)...1Gbits per second copper. m622ATM(8).......622Mbits per second (ATM). m155POS(9).......155Mbits per second (POS). m622POS(10)......622Mbits per second (POS). | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), m100BaseTX(2), m100BaseFX(3), m1000BaseFX(4), mT3(5), m155ATM(6), m1000BaseTX(7), m622ATM(8), m155POS(9), m622POS(10) | ||
| snSwPortInfoConnectorType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.7 | ||
| The type of connector that the port offers. The values are: other(1)...........other or unknown connector copper(2)..........Copper connector fiber(3)...........Fiber connector This describes the physical connector type | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), copper(2), fiber(3) | ||
| snSwPortInfoAdminStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.8 | ||
| The desired state of all ports. The testing(3) state indicates that no operational packets can be passed. (same as ifAdminStatus in MIB-II) | |||
| OBJECT-TYPE | |||
| INTEGER | up(1), down(2), testing(3) | ||
| snSwPortInfoLinkStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.9 | ||
| The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. (same as ifOperStatus in MIB-II) | |||
| OBJECT-TYPE | |||
| INTEGER | up(1), down(2), testing(3) | ||
| snSwPortInfoPortQos | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.10 | ||
| The Stand alone stackable switch Port Qos Priority values are: low(0) -- low prority high(1) -- high prority. The BigIron Port Qos Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7) | |||
| OBJECT-TYPE | |||
| INTEGER | level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7) | ||
| snSwPortInfoPhysAddress | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.11 | ||
| The port physical address. The physical address represents the switch port. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| snSwPortStatsInFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.12 | ||
| The total number of packets received on the interface. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortStatsOutFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.13 | ||
| The total number of packets transmitted out of the interface. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortStatsAlignErrors | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.14 | ||
| dot3StatsAlignmentErrors : A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortStatsFCSErrors | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.15 | ||
| dot3StatsFCSErrors : A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortStatsMultiColliFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.16 | ||
| dot3StatsMultipleCollisionFrames : A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortStatsFrameTooLongs | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.17 | ||
| dot3StatsFrameTooLongs : A count of frames received on a particular interface that exceed the maximum permitted frame size. The count represented by an instance of this object is incremented when the frameTooLong status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortStatsTxColliFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.18 | ||
| A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. A frame that is counted by a combination of both dot3StatsSingleCollisionFrames and dot3StatsMultipleCollisionFrames objects. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortStatsRxColliFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.19 | ||
| A count of successfully received frames on a particular interface for which transmission is inhibited by more than one collision. This object is not specified in dot3 but it has the same functionarity as snSwPortStatsTxColliFrames. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortStatsFrameTooShorts | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.20 | ||
| A count of frames received on a particular interface that below the minimum permitted frame size. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortLockAddressCount | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.21 | ||
| The number of source MAC addresses are allowed for a port. Writing 0 to this object will allow any number of addresses. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..2048 | ||
| snSwPortStpPortEnable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.22 | ||
| The enabled/disabled status of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snSwPortDhcpGateListId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.23 | ||
| The ID for a DHCP gateway list entry relative to this switch port. 0 = unset or no assigned ID | |||
| OBJECT-TYPE | |||
| INTEGER | 0..32 | ||
| snSwPortName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.24 | ||
| Port Name string. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| snSwPortStatsInBcastFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.25 | ||
| The total number of broadcast packets received on the interface. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortStatsOutBcastFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.26 | ||
| The total number of broadcast packets transmitted out of the interface. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortStatsInMcastFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.27 | ||
| The total number of multicast packets received on the interface. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortStatsOutMcastFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.28 | ||
| The total number of multicast packets transmitted out of the interface. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortStatsInDiscard | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.29 | ||
| The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortStatsOutDiscard | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.30 | ||
| The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortStatsMacStations | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.31 | ||
| The total number of MAC Stations connected to the interface. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwPortCacheGroupId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.32 | ||
| Cache Group ID for the interface. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwPortTransGroupId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.33 | ||
| Transparent Group ID for the interface. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwPortInfoAutoNegotiate | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.34 | ||
| This feature only applies to Gigabit Ethernet ports. If set to disable(0), port will be put to non-negotiation mode. If set to enable(1), port will start auto-negotiation indefinitely until succeed. If set to negFullAuto(2), the port will start with auto- negotiation, if the negotiation failed, then it will automatically switch to non-negotiation mode. Stackable products (except TurboIron 8) Gigabit Ethernet ports do not support negFullAuto(2). If set to global(3), port negotiation mode follows the value of snSwGlobalAutoNegotiate. Non-Gigabit Ethernet port returns the value other(4). | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1), negFullAuto(2), global(3), other(4) | ||
| snSwPortInfoFlowControl | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.35 | ||
| Enable/Disbale port flow control. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snSwPortInfoGigType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.36 | ||
| The media type for the port. The values are: m1000BaseSX(0)....1Gbits per second fiber, with a short wavelength transceiver. m1000BaseLX(1)....1Gbits per second fiber, with a long wavelength transceiver (3km). m1000BaseLH(2)....1Gbits per second fiber, with a special wavelength transceiver (50km). notApplicable(255)....a non-gigabit port. | |||
| OBJECT-TYPE | |||
| INTEGER | m1000BaseSX(0), m1000BaseLX(1), m1000BaseLH(2), notApplicable(255) | ||
| snSwPortStatsLinkChange | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.37 | ||
| The total number of link state change of the interface. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snSwPortIfIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.38 | ||
| In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 1213 and RFC 1573. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwPortDescr | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.39 | ||
| A textual string containing the slot/port information about the interface. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| snSwPortInOctets | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.40 | ||
| The total number of octets received on the interface, including framing characters. This object is a 64-bit counter of the ifInOctets object, defined in RFC 1213. The octet string is in big-endian byte order. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| snSwPortOutOctets | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.41 | ||
| The total number of octets transmitted out of the interface, including framing characters. This object is a 64-bit counter of the ifOutOctets object, defined in RFC 1213. The octet string is in big-endian byte order. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| snSwPortStatsInBitsPerSec | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.42 | ||
| The number of bits per second received on the interface over a 5 minutes interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| snSwPortStatsOutBitsPerSec | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.43 | ||
| The number of bits per second transmitted out of the interface over a 5 minutes interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| snSwPortStatsInPktsPerSec | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.44 | ||
| The number of packets per second received on the interface over a 5 minutes interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| snSwPortStatsOutPktsPerSec | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.45 | ||
| The number of packets per second transmitted out of the interface over a 5 minutes interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| snSwPortStatsInUtilization | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.46 | ||
| The input network utilization in hundredths of a percent over a 5 minutes interval. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..10000 | ||
| snSwPortStatsOutUtilization | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.47 | ||
| The output network utilization in hundredths of a percent over a 5 minutes interval. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..10000 | ||
| snSwPortFastSpanPortEnable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.48 | ||
| The enabled/disabled fast span port status of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snSwPortFastSpanUplinkEnable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.49 | ||
| The enabled/disabled fast span uplink status of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snSwPortVlanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.50 | ||
| The ID of a VLAN of which this port is a member. Port must be untagged. For tagged port which belongs to multiple VLANs, this object return 0 which is an invalid VLAN ID value. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..4095 | ||
| snSwPortRouteOnly | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.51 | ||
| Enable/Disable L2 switching of a routing switch port. By default, the routing switch performs routing first. If routing failed, it performs switching. Enable route only instrcuts the routing switch to perform routing only. For a L2 switching only product, reading this object always return 'disabled', writing 'enabled' to this object takes no effect. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snFdbInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4 | ||
| OBJECT IDENTIFIER | |||
| snFdbTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1 | ||
| This table contains snFdb information for each station known to the system, one entry per station. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnFdbEntry | |||
| snFdbEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1 | ||
| Each entry represents the information of a static MAC station. | |||
| OBJECT-TYPE | |||
| SnFdbEntry | |||
| snFdbStationIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.1 | ||
| The FDB Station index to the Fdb Station Table. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..256 | ||
| snFdbStationAddr | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.2 | ||
| The snFdbs physical address. The physical address represents a MAC Station. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| snFdbStationPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.3 | ||
| Station slot/port number. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only). | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snFdbVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.4 | ||
| The Station VLan ID. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| snFdbStationQos | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.5 | ||
| The Stand alone stackable station Qos Priority values are: low(0) -- low prority high(1) -- high prority. The BigIron switch station Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7) | |||
| OBJECT-TYPE | |||
| INTEGER | level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7) | ||
| snFdbStationType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.6 | ||
| The station type values are: notSupported -- a read value only : this product does not support MultiLayer Switching. host -- any MAC station. router -- a router-typed station. | |||
| OBJECT-TYPE | |||
| INTEGER | notSupported(0), host(1), router(2) | ||
| snFdbRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.7 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), valid(2), delete(3), create(4) | ||
| snPortStpInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5 | ||
| OBJECT IDENTIFIER | |||
| snPortStpTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1 | ||
| A specific snPortStpTable consists of a number of switch ports. This table only exists if only if snVLanByPortTable exists and snVLanByPortStpMode is enabled for each VLAN. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnPortStpEntry | |||
| snPortStpEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1 | ||
| An entry in the snPortStpTable indicates the configuration on a specified port. A SNMP SET PDU for a row of the snPortStpTable requires the entired sequence of the MIB Objects in each snPortStpEntry stored in one PDU. Otherwise, GENERR return-value will be returned. | |||
| OBJECT-TYPE | |||
| SnPortStpEntry | |||
| snPortStpVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.1 | ||
| The VLAN ID of the VLAN switch community. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| snPortStpPortNum | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.2 | ||
| The port number of the Switch. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only). | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snPortStpPortPriority | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.3 | ||
| The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of dot1dStpPort. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| snPortStpPathCost | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.4 | ||
| dot1dStpPortPathCost : The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN. Writing value zero to this object sets path cost to a default value which automatically changes according to port speed. Reading value zero indicates an unknown path cost value because port speed cannot be determined due to speed auto sense in progress. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| snPortStpOperState | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.5 | ||
| By default, this mode is set to notActivated(0). notActivated(0)...the Port STP entry is not activated and not in running mode. activated(1)......the Port STP entry is activated and in running mode | |||
| OBJECT-TYPE | |||
| INTEGER | notActivated(0), activated(1) | ||
| snPortStpPortEnable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.6 | ||
| The enabled/disabled status of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| snPortStpPortForwardTransitions | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.7 | ||
| The number of times this port has transitioned from the Learning state to the Forwarding state. | |||
| OBJECT-TYPE | |||
| Counter | |||
| snPortStpPortState | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.8 | ||
| The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpPortEnable), this object will have a value of disabled(1). | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6) | ||
| snPortStpPortDesignatedCost | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.9 | ||
| The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snPortStpPortDesignatedRoot | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.10 | ||
| The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached. | |||
| OBJECT-TYPE | |||
| BridgeId | |||
| snPortStpPortDesignatedBridge | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.11 | ||
| The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment. | |||
| OBJECT-TYPE | |||
| BridgeId | |||
| snPortStpPortDesignatedPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.12 | ||
| The Port Identifier of the port on the Designated Bridge for this port's segment. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| snTrunkInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6 | ||
| OBJECT IDENTIFIER | |||
| snTrunkTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1 | ||
| A specific snTrunkTable consists of a number of Trunk port-mask. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnTrunkEntry | |||
| snTrunkEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1 | ||
| An entry in the snTrunkTable indicates the configuration on a specified Trunk port membership. | |||
| OBJECT-TYPE | |||
| SnTrunkEntry | |||
| snTrunkIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1.1 | ||
| The number of the trunk entries can be configured. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..64 | ||
| snTrunkPortMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1.2 | ||
| Trunk membership of the Switch. | |||
| OBJECT-TYPE | |||
| PortMask | |||
| snTrunkType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1.3 | ||
| The trunk connection type which specifies what device the trunk ports are connected to. | |||
| OBJECT-TYPE | |||
| INTEGER | switch(1), server(2) | ||
| snMSTrunkTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2 | ||
| A table contains the configuration of port members of multi-slot trunk groups. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnMSTrunkEntry | |||
| snMSTrunkEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1 | ||
| An entry of the snMSTrunkTable. | |||
| OBJECT-TYPE | |||
| SnMSTrunkEntry | |||
| snMSTrunkPortIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.1 | ||
| The primary port of a trunk group. For module with Gig ports, primary port is port 1, 3, 5, 7. For module with 10/100 ports, primary port is port 1, 5, 9, 13, 17, 21. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snMSTrunkPortList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.2 | ||
| A list of port indices which are the port membership of a trunk group. Each port index is a 16-bit integer in big endian order. The first port index must be the primary port index. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| snMSTrunkType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.3 | ||
| The trunk connection type which specifies what device the trunk ports are connected to. | |||
| OBJECT-TYPE | |||
| INTEGER | switch(1), server(2) | ||
| snMSTrunkRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.4 | ||
| To create or delete a table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snSwSummary | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7 | ||
| OBJECT IDENTIFIER | |||
| snSwSummaryMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.1 | ||
| The Switch Group Configuration Summary is configured either enabled or disabled and the default is disabled mode. enabled(1)...........activate Switch Configuration Summary. disabled(0)..........no Switch Configuration Summary. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snVLanByPortEosTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.2 | ||
| A table of encoded octet strings of entries in snVLanByPortTable. The number of entries is determined by packing of rows from snVLanByPortTable. If snSwSummaryMode is disabled(0), the GET-RESPONSE of this object is NO-SUCH. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnVLanByPortEosEntry | |||
| snVLanByPortEosEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.2.1 | ||
| An EOS row in the table of encoded octet strings for table snVLanByPortTable. Instance returned in Response PDU, On GETs, instance specified is the instance returned. On GET-NEXTs, instance returned is the instance of the last record contained in the octet string. Entries in the table can not be created or deleted via SNMP. | |||
| OBJECT-TYPE | |||
| SnVLanByPortEosEntry | |||
| snVLanByPortCfgEos | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.2.1.1 | ||
| An encoded octet string. On reads it contains an integral number of rows from table snVLanByPortTable. The size of each encoded octet string is less than or equal to 1400 bytes. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..1400) | ||
| snVLanByPortVLanEosIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.2.1.2 | ||
| Each VLAN EOS Buffer Identifier have a multiple VLAN table entries. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snSwPortEosTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.3 | ||
| A table of encoded octet strings of entries in snSwPortInfoTable. The number of entries is determined by packing of rows from snSwPortInfoTable. If snSwSummaryMode is disabled(0), the GET-RESPONSE of this object is NO-SUCH. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnSwPortEosEntry | |||
| snSwPortEosEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.3.1 | ||
| An EOS row in the table of encoded octet strings for table snSwPortInfoTable. Instance returned in Response PDU, On GETs, instance specified is the instance returned. On GET-NEXTs, instance returned is the instance of the last record contained in the octet string. Entries in the table can not be created or deleted via SNMP. | |||
| OBJECT-TYPE | |||
| SnSwPortEosEntry | |||
| snSwPortCfgEos | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.3.1.1 | ||
| An encoded octet string. On reads it contains an integral number of rows from table snSwPortInfoTable. The size of each encoded octet string is less than or equal to 1400 bytes. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..1400) | ||
| snSwPortEosPortNum | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.3.1.2 | ||
| The port EOS buffer index. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snFdbEosTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.4 | ||
| A table of encoded octet strings of entries in snFdbTable. The number of entries is determined by packing of rows from snFdbTable. If snSwSummaryMode is disabled(0), the GET-RESPONSE of this object is NO-SUCH. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnFdbEosEntry | |||
| snFdbEosEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.4.1 | ||
| An EOS row in the table of encoded octet strings for table snFdbTable. Instance returned in Response PDU, On GETs, instance specified is the instance returned. On GET-NEXTs, instance returned is the instance of the last record contained in the octet string. Entries in the table can not be created or deleted via SNMP. | |||
| OBJECT-TYPE | |||
| SnFdbEosEntry | |||
| snFdbCfgEos | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.4.1.1 | ||
| An encoded octet string. On reads it contains an integral number of rows from table snFdbTable. The size of each encoded octet string is less than or equal to 1400 bytes. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..1400) | ||
| snFdbStationEosIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.4.1.2 | ||
| The FDB Station Eos index to the Fdb Station Eos Buffer. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snPortStpEosTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.5 | ||
| A table of encoded octet strings of entries in snPortStpTable. The number of entries is determined by packing of rows from snPortStpTable. If snSwSummaryMode is disabled(0), the GET-RESPONSE of this object is NO-SUCH. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnPortStpEosEntry | |||
| snPortStpEosEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.5.1 | ||
| An EOS row in the table of encoded octet strings for table snPortStpTable. Instance returned in Response PDU, On GETs, instance specified is the instance returned. On GET-NEXTs, instance returned is the instance of the last record contained in the octet string. Entries in the table can not be created or deleted via SNMP. | |||
| OBJECT-TYPE | |||
| SnPortStpEosEntry | |||
| snPortStpCfgEos | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.5.1.1 | ||
| An encoded octet string. On reads it contains an integral number of rows from table snPortStpTable. The size of each encoded octet string is less than or equal to 1400 bytes. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..1400) | ||
| snDhcpGatewayListInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8 | ||
| OBJECT IDENTIFIER | |||
| snDhcpGatewayListTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1 | ||
| A table of DHCP gateway list of addresses. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnDhcpGatewayListEntry | |||
| snDhcpGatewayListEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1 | ||
| An entry in the IP Port Address table. | |||
| OBJECT-TYPE | |||
| SnDhcpGatewayListEntry | |||
| snDhcpGatewayListId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1.1 | ||
| The ID for a DHCP gateway list entry. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..32 | ||
| snDhcpGatewayListAddrList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1.2 | ||
| The DHCP gateway address list for each DHCP gateway list ID. This list contains 1 to 8 IP addresses represented by octet string. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4..32) | ||
| snDhcpGatewayListRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1.3 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row or modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), valid(2), delete(3), create(4) | ||
| snDnsInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.9 | ||
| OBJECT IDENTIFIER | |||
| snDnsDomainName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.9.1 | ||
| DNS Domain Name string. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..80) | ||
| snDnsGatewayIpAddrList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.9.2 | ||
| The DNS Gateway IP address list. This list contains 4 IP addresses represented by octet string. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| snMacFilter | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10 | ||
| OBJECT IDENTIFIER | |||
| snMacFilterTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1 | ||
| MAC filter table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnMacFilterEntry | |||
| snMacFilterEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1 | ||
| An entry in the MAC filter table. | |||
| OBJECT-TYPE | |||
| SnMacFilterEntry | |||
| snMacFilterIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.1 | ||
| The table index for a filter entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snMacFilterAction | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.2 | ||
| Action to take if the Mac packet match with this filter. | |||
| OBJECT-TYPE | |||
| INTEGER | deny(0), permit(1) | ||
| snMacFilterSourceMac | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.3 | ||
| Source MAC address. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| snMacFilterSourceMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.4 | ||
| Source MAC subnet mask. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| snMacFilterDestMac | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.5 | ||
| Destination MAC address. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| snMacFilterDestMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.6 | ||
| Destination MAC subnet mask. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| snMacFilterOperator | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.7 | ||
| Type of comparison to perform. | |||
| OBJECT-TYPE | |||
| INTEGER | equal(0), notEqual(1), less(2), greater(3) | ||
| snMacFilterFrameType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.8 | ||
| Frame Type: ethernet-type, LLC and SNAP types | |||
| OBJECT-TYPE | |||
| INTEGER | notUsed(0), ethernet(1), llc(2), snap(3) | ||
| snMacFilterFrameTypeNum | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.9 | ||
| Frame Type Number. 0 means NA | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| snMacFilterRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.10 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4), modify(5) | ||
| snMacFilterPortAccessTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2 | ||
| MAC Filter port access table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnMacFilterPortAccessEntry | |||
| snMacFilterPortAccessEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1 | ||
| An entry in the MAC Filter Port access table. | |||
| OBJECT-TYPE | |||
| SnMacFilterPortAccessEntry | |||
| snMacFilterPortAccessPortIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1.1 | ||
| The port index. For FastIron/NetIron products, port index value is from 1 to 42 For BigIron products, port index is an encoded number: The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number. For virtual router interface, slot number is 15, port number is the virtual router port from 1 to 60. Therefore, port index value for BigIron is from 257 to 3900. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..3900 | ||
| snMacFilterPortAccessFilters | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1.2 | ||
| 1st octet correspond to 1st filter number and so on. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| snMacFilterPortAccessRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1.3 | ||
| This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid | |||
| OBJECT-TYPE | |||
| INTEGER | invalid(1), valid(2), delete(3), create(4) | ||
| snNTP | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11 | ||
| OBJECT IDENTIFIER | |||
| snNTPGeneral | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1 | ||
| OBJECT IDENTIFIER | |||
| snNTPPollInterval | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.1 | ||
| Interval specifies how often to poll the NTP server. Each unit is one second. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| snNTPTimeZone | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.2 | ||
| Time zone. | |||
| OBJECT-TYPE | |||
| INTEGER | alaska(0), aleutian(1), arizona(2), central(3), eastIndiana(4), eastern(5), hawaii(6), michigan(7), mountain(8), pacific(9), samoa(10), gmtPlus12(11), gmtPlus11(12), gmtPlus10(13), gmtPlus9(14), gmtPlus8(15), gmtPlus7(16), gmtPlus6(17), gmtPlus5(18), gmtPlus4(19), gmtPlus3(20), gmtPlus2(21), gmtPlus1(22), gmt(23), gmtMinus1(24), gmtMinus2(25), gmtMinus3(26), gmtMinus4(27), gmtMinus5(28), gmtMinus6(29), gmtMinus7(30), gmtMinus8(31), gmtMinus9(32), gmtMinus10(33), gmtMinus11(34), gmtMinus12(35) | ||
| snNTPSummerTimeEnable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.3 | ||
| Enable/Disable daylight saving time. This enables daylight saving time for time/date starting 02:00:00 of first Sunday in April and ending 02:00:00 of last Sunday in October every year. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snNTPSystemClock | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.4 | ||
| System clock, in the following format: octet 0: seconds after the minute [0-60] octet 1: minutes after the hour [0-59] octet 2: hours since midnight [0-23] octet 3: day of the month [1-31] octet 4: months since January [0-11] octet 5: years since 1900 octet 6: days since Sunday [0-6] Setting this object requires valid value in octets 0 to 5, and zero in octet 6. System clock can be disabled by setting zero to all octets. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(7) | ||
| snNTPSync | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.5 | ||
| Initiate time synchronization to the NTP servers. For set operation, only 'synchronize(2)' is accepted. For get operation, always return 'other(1)'. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), synchronize(2) | ||
| snNTPServerTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2 | ||
| NTP (Network Time Protocol) server table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnNTPServerEntry | |||
| snNTPServerEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1 | ||
| An entry in the NTP server table. | |||
| OBJECT-TYPE | |||
| SnNTPServerEntry | |||
| snNTPServerIp | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1.1 | ||
| NTP server IP address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snNTPServerVersion | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1.2 | ||
| NTP server version. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..4 | ||
| snNTPServerRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1.3 | ||
| To create or delete a NTP server table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), valid(2), delete(3), create(4) | ||
| snRadius | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12 | ||
| OBJECT IDENTIFIER | |||
| snRadiusGeneral | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1 | ||
| OBJECT IDENTIFIER | |||
| snRadiusSNMPAccess | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.1 | ||
| Indicate whether Radius group MIB obejcts can be accessed by SNMP manager. If value is disabled, all Radius group MIB objects return 'general error'. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snRadiusEnableTelnetAuth | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.2 | ||
| Enable/Disable telnet authentication specified by 'snRadiusLoginMethod'. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snRadiusRetransmit | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.3 | ||
| The number of authentication query retransmissions to the Radius server. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..5 | ||
| snRadiusTimeOut | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.4 | ||
| Interval specifies how long to wait for authentication reply from the Radius server, each unit is one second. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..15 | ||
| snRadiusDeadTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.5 | ||
| Interval specifies Radius server dead time, each unit is one minute. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..5 | ||
| snRadiusKey | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.6 | ||
| Authentication key. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..16) | ||
| snRadiusLoginMethod | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.7 | ||
| A sequence of authentication methods. Each octet represents a method to authenticate the user login process. Each octet has the following enumeration value: enable(1) - authenticate by command line interface enable password radius(2) - authenticate by requesting radius server local(3) - authenticate by local user account table line(4) - authenticate by telnet password tacplus(5) - authenticate by requesting tacplus server none(6) - do not authenticate tacacs(7) - authenticate by requesting tacacs server Setting a zero length octet string invalidates all previous authentication methods. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..7) | ||
| snRadiusEnableMethod | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.8 | ||
| A sequence of authentication methods. Each octet represents a method to authenticate the user entering priviledge mode of the command line interface. Each octet has the following enumeration value: enable(1) - authenticate by command line interface enable password radius(2) - authenticate by requesting radius server local(3) - authenticate by local user account table line(4) - authenticate by telnet password tacplus(5) - authenticate by requesting tacplus server none(6) - do not authenticate tacacs(7) - authenticate by requesting tacacs server Setting a zero length octet string invalidates all previous authentication methods. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..7) | ||
| snRadiusWebServerMethod | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.9 | ||
| A sequence of authentication methods. Each octet represents a method to authenticate the user accessing the web-server. Each octet has the following enumeration value: enable(1) - authenticate by command line interface enable password radius(2) - authenticate by requesting radius server local(3) - authenticate by local user account table line(4) - authenticate by telnet password tacplus(5) - authenticate by requesting tacplus server none(6) - do not authenticate tacacs(7) - authenticate by requesting tacacs server Setting a zero length octet string invalidates all previous authentication methods. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..7) | ||
| snRadiusSNMPServerMethod | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.10 | ||
| A sequence of authentication methods. Each octet represents a method to authenticate the user accessing the snmp-server. Each octet has the following enumeration value: enable(1) - authenticate by command line interface enable password radius(2) - authenticate by requesting radius server local(3) - authenticate by local user account table line(4) - authenticate by telnet password tacplus(5) - authenticate by requesting tacplus server none(6) - do not authenticate tacacs(7) - authenticate by requesting tacacs server Setting a zero length octet string invalidates all previous authentication methods. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..7) | ||
| snRadiusServerTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2 | ||
| Radius server table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnRadiusServerEntry | |||
| snRadiusServerEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1 | ||
| An entry in the Radius server table. | |||
| OBJECT-TYPE | |||
| SnRadiusServerEntry | |||
| snRadiusServerIp | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.1 | ||
| Radius server IP address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snRadiusServerAuthPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.2 | ||
| Authentication UDP port number. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snRadiusServerAcctPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.3 | ||
| Account UDP port number. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snRadiusServerRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.4 | ||
| To create or delete a Radius server table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), valid(2), delete(3), create(4) | ||
| snTacacs | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13 | ||
| OBJECT IDENTIFIER | |||
| snTacacsGeneral | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1 | ||
| OBJECT IDENTIFIER | |||
| snTacacsRetransmit | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.1 | ||
| The number of authentication query retransmissions to the Tacacs server. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..5 | ||
| snTacacsTimeOut | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.2 | ||
| Interval specifies how long to wait for authentication reply from the Tacacs server, each unit is one second. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..15 | ||
| snTacacsDeadTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.3 | ||
| Interval specifies Tacacs server dead time, each unit is one minute. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..5 | ||
| snTacacsKey | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.4 | ||
| Authentication key. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..16) | ||
| snTacacsSNMPAccess | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.5 | ||
| Indicate whether Tacacs group MIB obejcts can be accessed by SNMP manager. If value is disabled, all Tacacs group MIB objects return 'general error'. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| snTacacsServerTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2 | ||
| Tacacs server table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnTacacsServerEntry | |||
| snTacacsServerEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1 | ||
| An entry in the Tacacs server table. | |||
| OBJECT-TYPE | |||
| SnTacacsServerEntry | |||
| snTacacsServerIp | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.1 | ||
| Tacacs server IP address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| snTacacsServerAuthPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.2 | ||
| Authentication UDP port number. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snTacacsServerRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.3 | ||
| To create or delete a Tacacs server table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), valid(2), delete(3), create(4) | ||
| snQos | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14 | ||
| OBJECT IDENTIFIER | |||
| snQosProfileTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1 | ||
| A table contains the configuration of qos profile groups. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnQosProfileEntry | |||
| snQosProfileEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1 | ||
| An entry of the snQosProfileTable. | |||
| OBJECT-TYPE | |||
| SnQosProfileEntry | |||
| snQosProfileIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.1 | ||
| The table index of QOS Profile. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..4 | ||
| snQosProfileName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.2 | ||
| Qos Profile Name string. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| snQosProfileRequestedBandwidth | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.3 | ||
| Qos Profile Requested Bandwidth. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..100 | ||
| snQosProfileCalculatedBandwidth | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.4 | ||
| Qos Profile Calculated Bandwidth. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..100 | ||
| snQosBindTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2 | ||
| A table contains the configuration of 802.1p to qos profile binding groups. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnQosBindEntry | |||
| snQosBindEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1 | ||
| An entry of the snQosBindTable. | |||
| OBJECT-TYPE | |||
| SnQosBindEntry | |||
| snQosBindIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1.1 | ||
| The table index of QOS Bind. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..8 | ||
| snQosBindPriority | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1.2 | ||
| QOS bind priority. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| snQosBindProfileIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1.3 | ||
| QOS Bind Profile Index. This is pointer to the index of snQosProfile Table. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..4 | ||
| DisplayString | |||
| OCTET STRING | |||
| PhysAddress | |||
| OCTET STRING | |||
| MacAddress | |||
| OCTET STRING | SIZE(6) | ||
| BridgeId | |||
| OCTET STRING | SIZE(8) | ||
| Timeout | |||
| INTEGER | |||
| PortMask | |||
| INTEGER | |||
| SnVLanByPortEntry | |||
| SEQUENCE | |||
| INTEGER as snVLanByPortVLanIndex | |||
| INTEGER as snVLanByPortVLanId | |||
| PortMask as snVLanByPortPortMask | |||
| INTEGER as snVLanByPortQos | |||
| INTEGER as snVLanByPortStpMode | |||
| INTEGER as snVLanByPortStpPriority | |||
| INTEGER as snVLanByPortStpGroupMaxAge | |||
| INTEGER as snVLanByPortStpGroupHelloTime | |||
| INTEGER as snVLanByPortStpGroupForwardDelay | |||
| INTEGER as snVLanByPortRowStatus | |||
| INTEGER as snVLanByPortOperState | |||
| INTEGER as snVLanByPortBaseNumPorts | |||
| INTEGER as snVLanByPortBaseType | |||
| INTEGER as snVLanByPortStpProtocolSpecification | |||
| Timeout as snVLanByPortStpMaxAge | |||
| Timeout as snVLanByPortStpHelloTime | |||
| INTEGER as snVLanByPortStpHoldTime | |||
| Timeout as snVLanByPortStpForwardDelay | |||
| TimeTicks as snVLanByPortStpTimeSinceTopologyChange | |||
| Counter as snVLanByPortStpTopChanges | |||
| INTEGER as snVLanByPortStpRootCost | |||
| INTEGER as snVLanByPortStpRootPort | |||
| BridgeId as snVLanByPortStpDesignatedRoot | |||
| MacAddress as snVLanByPortBaseBridgeAddress | |||
| DisplayString as snVLanByPortVLanName | |||
| INTEGER as snVLanByPortRouterIntf | |||
| OCTET STRING as snVLanByPortChassisPortMask | |||
| SnVLanByProtocolEntry | |||
| SEQUENCE | |||
| INTEGER as snVLanByProtocolVLanId | |||
| INTEGER as snVLanByProtocolIndex | |||
| INTEGER as snVLanByProtocolDynamic | |||
| PortMask as snVLanByProtocolStaticMask | |||
| PortMask as snVLanByProtocolExcludeMask | |||
| INTEGER as snVLanByProtocolRouterIntf | |||
| INTEGER as snVLanByProtocolRowStatus | |||
| PortMask as snVLanByProtocolDynamicMask | |||
| OCTET STRING as snVLanByProtocolChassisStaticMask | |||
| OCTET STRING as snVLanByProtocolChassisExcludeMask | |||
| OCTET STRING as snVLanByProtocolChassisDynamicMask | |||
| DisplayString as snVLanByProtocolVLanName | |||
| SnVLanByIpSubnetEntry | |||
| SEQUENCE | |||
| INTEGER as snVLanByIpSubnetVLanId | |||
| IpAddress as snVLanByIpSubnetIpAddress | |||
| IpAddress as snVLanByIpSubnetSubnetMask | |||
| INTEGER as snVLanByIpSubnetDynamic | |||
| PortMask as snVLanByIpSubnetStaticMask | |||
| PortMask as snVLanByIpSubnetExcludeMask | |||
| INTEGER as snVLanByIpSubnetRouterIntf | |||
| INTEGER as snVLanByIpSubnetRowStatus | |||
| PortMask as snVLanByIpSubnetDynamicMask | |||
| OCTET STRING as snVLanByIpSubnetChassisStaticMask | |||
| OCTET STRING as snVLanByIpSubnetChassisExcludeMask | |||
| OCTET STRING as snVLanByIpSubnetChassisDynamicMask | |||
| DisplayString as snVLanByIpSubnetVLanName | |||
| SnVLanByIpxNetEntry | |||
| SEQUENCE | |||
| INTEGER as snVLanByIpxNetVLanId | |||
| OCTET STRING as snVLanByIpxNetNetworkNum | |||
| INTEGER as snVLanByIpxNetFrameType | |||
| INTEGER as snVLanByIpxNetDynamic | |||
| PortMask as snVLanByIpxNetStaticMask | |||
| PortMask as snVLanByIpxNetExcludeMask | |||
| INTEGER as snVLanByIpxNetRouterIntf | |||
| INTEGER as snVLanByIpxNetRowStatus | |||
| PortMask as snVLanByIpxNetDynamicMask | |||
| OCTET STRING as snVLanByIpxNetChassisStaticMask | |||
| OCTET STRING as snVLanByIpxNetChassisExcludeMask | |||
| OCTET STRING as snVLanByIpxNetChassisDynamicMask | |||
| DisplayString as snVLanByIpxNetVLanName | |||
| SnVLanByATCableEntry | |||
| SEQUENCE | |||
| INTEGER as snVLanByATCableVLanId | |||
| INTEGER as snVLanByATCableIndex | |||
| INTEGER as snVLanByATCableRouterIntf | |||
| INTEGER as snVLanByATCableRowStatus | |||
| OCTET STRING as snVLanByATCableChassisStaticMask | |||
| DisplayString as snVLanByATCableVLanName | |||
| SnSwPortInfoEntry | |||
| SEQUENCE | |||
| INTEGER as snSwPortInfoPortNum | |||
| INTEGER as snSwPortInfoMonitorMode | |||
| INTEGER as snSwPortInfoTagType | |||
| INTEGER as snSwPortInfoChnMode | |||
| INTEGER as snSwPortInfoSpeed | |||
| INTEGER as snSwPortInfoMediaType | |||
| INTEGER as snSwPortInfoConnectorType | |||
| INTEGER as snSwPortInfoAdminStatus | |||
| INTEGER as snSwPortInfoLinkStatus | |||
| INTEGER as snSwPortInfoPortQos | |||
| PhysAddress as snSwPortInfoPhysAddress | |||
| Counter as snSwPortStatsInFrames | |||
| Counter as snSwPortStatsOutFrames | |||
| Counter as snSwPortStatsAlignErrors | |||
| Counter as snSwPortStatsFCSErrors | |||
| Counter as snSwPortStatsMultiColliFrames | |||
| Counter as snSwPortStatsFrameTooLongs | |||
| Counter as snSwPortStatsTxColliFrames | |||
| Counter as snSwPortStatsRxColliFrames | |||
| Counter as snSwPortStatsFrameTooShorts | |||
| INTEGER as snSwPortLockAddressCount | |||
| INTEGER as snSwPortStpPortEnable | |||
| INTEGER as snSwPortDhcpGateListId | |||
| DisplayString as snSwPortName | |||
| Counter as snSwPortStatsInBcastFrames | |||
| Counter as snSwPortStatsOutBcastFrames | |||
| Counter as snSwPortStatsInMcastFrames | |||
| Counter as snSwPortStatsOutMcastFrames | |||
| Counter as snSwPortStatsInDiscard | |||
| Counter as snSwPortStatsOutDiscard | |||
| INTEGER as snSwPortStatsMacStations | |||
| INTEGER as snSwPortCacheGroupId | |||
| INTEGER as snSwPortTransGroupId | |||
| INTEGER as snSwPortInfoAutoNegotiate | |||
| INTEGER as snSwPortInfoFlowControl | |||
| INTEGER as snSwPortInfoGigType | |||
| Counter as snSwPortStatsLinkChange | |||
| INTEGER as snSwPortIfIndex | |||
| DisplayString as snSwPortDescr | |||
| OCTET STRING as snSwPortInOctets | |||
| OCTET STRING as snSwPortOutOctets | |||
| Gauge as snSwPortStatsInBitsPerSec | |||
| Gauge as snSwPortStatsOutBitsPerSec | |||
| Gauge as snSwPortStatsInPktsPerSec | |||
| Gauge as snSwPortStatsOutPktsPerSec | |||
| INTEGER as snSwPortStatsInUtilization | 0..10000 | ||
| INTEGER as snSwPortStatsOutUtilization | 0..10000 | ||
| INTEGER as snSwPortFastSpanPortEnable | |||
| INTEGER as snSwPortFastSpanUplinkEnable | |||
| INTEGER as snSwPortVlanId | |||
| INTEGER as snSwPortRouteOnly | |||
| SnFdbEntry | |||
| SEQUENCE | |||
| INTEGER as snFdbStationIndex | |||
| PhysAddress as snFdbStationAddr | |||
| INTEGER as snFdbStationPort | |||
| INTEGER as snFdbVLanId | |||
| INTEGER as snFdbStationQos | |||
| INTEGER as snFdbStationType | |||
| INTEGER as snFdbRowStatus | |||
| SnPortStpEntry | |||
| SEQUENCE | |||
| INTEGER as snPortStpVLanId | |||
| INTEGER as snPortStpPortNum | |||
| INTEGER as snPortStpPortPriority | |||
| INTEGER as snPortStpPathCost | |||
| INTEGER as snPortStpOperState | |||
| INTEGER as snPortStpPortEnable | |||
| Counter as snPortStpPortForwardTransitions | |||
| INTEGER as snPortStpPortState | |||
| INTEGER as snPortStpPortDesignatedCost | |||
| BridgeId as snPortStpPortDesignatedRoot | |||
| BridgeId as snPortStpPortDesignatedBridge | |||
| OCTET STRING as snPortStpPortDesignatedPort | |||
| SnTrunkEntry | |||
| SEQUENCE | |||
| INTEGER as snTrunkIndex | |||
| PortMask as snTrunkPortMask | |||
| INTEGER as snTrunkType | |||
| SnMSTrunkEntry | |||
| SEQUENCE | |||
| INTEGER as snMSTrunkPortIndex | |||
| OCTET STRING as snMSTrunkPortList | |||
| INTEGER as snMSTrunkType | |||
| INTEGER as snMSTrunkRowStatus | |||
| SnVLanByPortEosEntry | |||
| SEQUENCE | |||
| OCTET STRING as snVLanByPortCfgEos | |||
| SnSwPortEosEntry | |||
| SEQUENCE | |||
| OCTET STRING as snSwPortCfgEos | |||
| SnFdbEosEntry | |||
| SEQUENCE | |||
| OCTET STRING as snFdbCfgEos | |||
| SnPortStpEosEntry | |||
| SEQUENCE | |||
| OCTET STRING as snPortStpCfgEos | |||
| SnDhcpGatewayListEntry | |||
| SEQUENCE | |||
| INTEGER as snDhcpGatewayListId | |||
| OCTET STRING as snDhcpGatewayListAddrList | |||
| INTEGER as snDhcpGatewayListRowStatus | |||
| SnMacFilterEntry | |||
| SEQUENCE | |||
| INTEGER as snMacFilterIndex | |||
| INTEGER as snMacFilterAction | |||
| MacAddress as snMacFilterSourceMac | |||
| MacAddress as snMacFilterSourceMask | |||
| MacAddress as snMacFilterDestMac | |||
| MacAddress as snMacFilterDestMask | |||
| INTEGER as snMacFilterOperator | |||
| INTEGER as snMacFilterFrameType | |||
| INTEGER as snMacFilterFrameTypeNum | |||
| INTEGER as snMacFilterRowStatus | |||
| SnMacFilterPortAccessEntry | |||
| SEQUENCE | |||
| INTEGER as snMacFilterPortAccessPortIndex | |||
| OCTET STRING as snMacFilterPortAccessFilters | |||
| INTEGER as snMacFilterPortAccessRowStatus | |||
| SnNTPServerEntry | |||
| SEQUENCE | |||
| IpAddress as snNTPServerIp | |||
| INTEGER as snNTPServerVersion | |||
| INTEGER as snNTPServerRowStatus | |||
| SnRadiusServerEntry | |||
| SEQUENCE | |||
| IpAddress as snRadiusServerIp | |||
| INTEGER as snRadiusServerAuthPort | |||
| INTEGER as snRadiusServerAcctPort | |||
| INTEGER as snRadiusServerRowStatus | |||
| SnTacacsServerEntry | |||
| SEQUENCE | |||
| IpAddress as snTacacsServerIp | |||
| INTEGER as snTacacsServerAuthPort | |||
| INTEGER as snTacacsServerRowStatus | |||
| SnQosProfileEntry | |||
| SEQUENCE | |||
| INTEGER as snQosProfileIndex | |||
| DisplayString as snQosProfileName | |||
| INTEGER as snQosProfileRequestedBandwidth | |||
| INTEGER as snQosProfileCalculatedBandwidth | |||
| SnQosBindEntry | |||
| SEQUENCE | |||
| INTEGER as snQosBindIndex | |||
| INTEGER as snQosBindPriority | |||
| INTEGER as snQosBindProfileIndex | |||