
IBM2212-MIB
File:
IBM2212-MIB.mib (9804 bytes)
Imported modules
Imported symbols
Defined Objects
| ibm |
1.3.6.1.4.1.2 |
| OBJECT IDENTIFIER |
|
|
|
| ibmProd |
1.3.6.1.4.1.2.6 |
| OBJECT IDENTIFIER |
|
|
|
| ibm2212 |
1.3.6.1.4.1.2.6.149 |
| OBJECT IDENTIFIER |
|
|
|
| ibm2212AdapEntry |
1.3.6.1.4.1.2.6.149.3.1.1.1 |
| An entry containing objects to describe the adapter in a given slot. |
| OBJECT-TYPE |
|
|
|
| |
Ibm2212AdapEntry |
|
|
| ibm2212AdapSlotNum |
1.3.6.1.4.1.2.6.149.3.1.1.1.1 |
| The number identifying a slot location where an adapter can be inserted. The 2212 has four fixed serial ports on the system card that are designated by slot 0. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..65535 |
|
| ibm2212AdapType |
1.3.6.1.4.1.2.6.149.3.1.1.1.2 |
| The type of adapter that is inserted into this slot. Not all of the adapter types listed above are necessarily currently available and supported. The four fixed serial ports on the system card are identified by the serial-4port-shallow(7) enumeration. If no adapter is present, the variable will take the value not-present(2). |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
unknown(1), not-present(2), eth-fast-1port(3), token-ring-1port(4), eth-fast-2port(5), token-ring-2port(6), serial-4port-shallow(7), isdn-bri-u-2port(8), isdn-bri-st-2port(9), isdn-pri-t1j1-1port(10), isdn-pri-e1-1port(11), compression-encryption(12), serial-4port-deep(13), isdn-pri-t1j1-2port(14), isdn-pri-e1-2port(15) |
|
| ibm2212AdapOperStatus |
1.3.6.1.4.1.2.6.149.3.1.1.1.3 |
| The operational status of this adapter. unknown (1) : If there was problem determining the operational status of the adapter. not-present (2) : If no adapter is currently inserted. enable-pending (3) : Adapter has been identified, but not yet enabled. enabled (4) : Adapter has been identified in valid slot and has been powered on and enabled. unknown-device (5) : Adapter is powered off because it is in the wrong slot or of unknown type. config-error (6) : Adapter has been identified, powered on and enabled, but failed to read its configuration data. not-powered (7) : Adapter has been identified in valid slot but is not currently powered on. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
unknown(1), not-present(2), enable-pending(3), enabled(4), unknown-device(5), hardware-error(6), not-powered(7) |
|
| ibm2212GraphicEntry |
1.3.6.1.4.1.2.6.149.3.1.2.1 |
| An entry mapping slot and port to an interface table ifIndex. |
| OBJECT-TYPE |
|
|
|
| |
Ibm2212GraphicEntry |
|
|
| ibm2212GraphicSlotNum |
1.3.6.1.4.1.2.6.149.3.1.2.1.1 |
| The number identifying a slot location where an adapter can be inserted. The 2212 has four fixed serial ports on the system card that are designated by slot 0. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..2147483647 |
|
| ibm2212GraphicPortNum |
1.3.6.1.4.1.2.6.149.3.1.2.1.2 |
| The number identifying a port on a given adapter. A port implies a physical connector is associated with it. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..2147483647 |
|
| ibm2212GraphicifIndex |
1.3.6.1.4.1.2.6.149.3.1.2.1.3 |
| The ifIndex of the interface table entry associated with this port on an adapter. By definition, the ifEntry has ifConnectorPresent = true. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
Defined Objects
| Ibm2212AdapEntry |
|
| SEQUENCE |
|
|
|
| |
INTEGER as ibm2212AdapSlotNum |
|
|
| |
INTEGER as ibm2212AdapType |
|
|
| |
INTEGER as ibm2212AdapOperStatus |
|
|
| Ibm2212GraphicEntry |
|
| SEQUENCE |
|
|
|
| |
INTEGER as ibm2212GraphicSlotNum |
|
|
| |
INTEGER as ibm2212GraphicPortNum |
|
|
| |
INTEGER as ibm2212GraphicifIndex |
|
|