IBM6611-MIB

File: IBM6611-MIB.mib (692876 bytes)

Imported modules

RFC1155-SMI SNMPv2-TC RFC-1212

Imported symbols

enterprises Counter Gauge
TimeTicks IpAddress DisplayString
OBJECT-TYPE

Defined Objects

ibm 1.3.6.1.4.1.2
OBJECT IDENTIFIER    

ibmProd 1.3.6.1.4.1.2.6
OBJECT IDENTIFIER    

ibm6611 1.3.6.1.4.1.2.6.2
OBJECT IDENTIFIER    

ibmSubagents 1.3.6.1.4.1.2.6.2.1
OBJECT IDENTIFIER    

ibmChipSets 1.3.6.1.4.1.2.6.2.2
OBJECT IDENTIFIER    

ibmChipSetIntel 1.3.6.1.4.1.2.6.2.2.1
OBJECT IDENTIFIER    

ibmChipSetIntel82596B 1.3.6.1.4.1.2.6.2.2.1.1
OBJECT IDENTIFIER    

ibmChipSetIBM 1.3.6.1.4.1.2.6.2.2.2
OBJECT IDENTIFIER    

ibmChipSetIBM8025A 1.3.6.1.4.1.2.6.2.2.2.1
OBJECT IDENTIFIER    

ibmChipSetIBM8025B 1.3.6.1.4.1.2.6.2.2.2.2
OBJECT IDENTIFIER    

ibmChipSetSignetics 1.3.6.1.4.1.2.6.2.2.3
OBJECT IDENTIFIER    

ibmChipSetSigneticsSCN68562 1.3.6.1.4.1.2.6.2.2.3.1
OBJECT IDENTIFIER    

ibmDSUs 1.3.6.1.4.1.2.6.2.3
OBJECT IDENTIFIER    


cylinkStatusTable 1.3.6.1.4.1.2.6.2.3.1.1
The cylink Status table. This table contains information about the current state of the Cylink CSUs attached to the system.
OBJECT-TYPE    
  SEQUENCE OF  
    CYLINKStatusEntry

cylinkStatusEntry 1.3.6.1.4.1.2.6.2.3.1.1.1
An entry in the cylink Status table.
OBJECT-TYPE    
  CYLINKStatusEntry  

cylinkIndex 1.3.6.1.4.1.2.6.2.3.1.1.1.1
An index value that uniquely identifies a cylink system interface. The interface identified by a particular value of this index is the same interface as identified by the same value in an ifIndex object instance.
OBJECT-TYPE    
  INTEGER  

cylinkLinkState 1.3.6.1.4.1.2.6.2.3.1.1.1.2
The current state of the link. The meanings of the values are: cylinkNotConnected(1) The link is not physically connected to the CSU. This may be due to loss of input circuit or loss of output circuit. cylinkNoInput(2) The input circuit is not connected. cylinkNoOutput(3) The output circuit is not connected. cylinkConnected(4) The link is connected to the CSU.
OBJECT-TYPE    
  INTEGER cylinkNotConnected(1), cylinkNoInput(2), cylinkNoOutput(3), cylinkConnected(4)  

cylinkLoopback 1.3.6.1.4.1.2.6.2.3.1.1.1.3
The loopback mode of the link. The meaning of values are: cylinkNoLoopback(1) The link is not in loopback mode. cylinkNearEndLoopback(2) The link has been placed in loopback mode at the near end: data is being looped back within the local CSU. cylinkFarEndLoopback(3) The link has been placed in loopback mode at the far end: data is being looped across the link to the remote CSU and back.
OBJECT-TYPE    
  INTEGER cylinkNoLoopback(1), cylinkNearEndLoopback(2), cylinkFarEndLoopback(3)  

cylinkQRSS 1.3.6.1.4.1.2.6.2.3.1.1.1.4
The Quasi-Random Signal Sequence test mode of the CSU. The value of the meanings are: cylinkNoQRSS(1) The CSU is not in QRSS mode. cylinkQRSSMaster(2) The CSU is transmitting a QRSS test pattern. cylinkQRSSSlave(3) The CSU is receiving a QRSS test pattern.
OBJECT-TYPE    
  INTEGER cylinkNoQRSS(1), cylinkQRSSMaster(2), cylinkQRSSSlave(3)  

cylinkConfigTable 1.3.6.1.4.1.2.6.2.3.1.3
The cylink Configuration table. This table contains information about the configuration of the Cylink CSUs attached to the system.
OBJECT-TYPE    
  SEQUENCE OF  
    CYLINKConfigEntry

cylinkConfigEntry 1.3.6.1.4.1.2.6.2.3.1.3.1
An entry in the cylink Configuration table.
OBJECT-TYPE    
  CYLINKConfigEntry  

cylinkConfigIndex 1.3.6.1.4.1.2.6.2.3.1.3.1.1
The index value which uniquely identifies the CSU to which this entry is applicable. The CSU identified by a particular value of this index is the same CSU as identified by the same value in a cylinkIndex object instance.
OBJECT-TYPE    
  INTEGER  

cylinkSerialNumber 1.3.6.1.4.1.2.6.2.3.1.3.1.2
The manufacturer's serial number of this CSU.
OBJECT-TYPE    
  INTEGER  

cylinkSoftwareVersion 1.3.6.1.4.1.2.6.2.3.1.3.1.3
The version number of the microcode running in the CSU.
OBJECT-TYPE    
  DisplayString SIZE(0..4)  

cylinkDTEFraming 1.3.6.1.4.1.2.6.2.3.1.3.1.4
The DTE framing selected (D4, or ESF). Framing conversion is automatically performed at both ends if the DTE is D4 framed and the network interface is ESF framed.
OBJECT-TYPE    
  INTEGER cylinkDTEFramingD4(0), cylinkDTEFramingESF(1)  

cylinkNetworkFraming 1.3.6.1.4.1.2.6.2.3.1.3.1.5
The network framing selected (D4, or ESF). Framing conversion is automatically performed at both ends if the DTE is D4 framed and the network interface is ESF framed.
OBJECT-TYPE    
  INTEGER cylinkNetworkFramingD4(0), cylinkNetworkFramingESF(1)  

cylinkDTEDS1Mode 1.3.6.1.4.1.2.6.2.3.1.3.1.6
The DTE DS-1 mode selected (B8ZS, or AMI).
OBJECT-TYPE    
  INTEGER cylinkDTEDS1ModeB8ZS(0), cylinkDTEDS1ModeAMI(1)  

cylinkNetworkDS1Mode 1.3.6.1.4.1.2.6.2.3.1.3.1.7
The network DS-1 mode selected (B8ZS, or AMI).
OBJECT-TYPE    
  INTEGER cylinkNetworkDS1ModeB8ZS(0), cylinkNetworkDS1ModeAMI(1)  

cylinkOnesResponsibility 1.3.6.1.4.1.2.6.2.3.1.3.1.8
The component selected for Ones Density Responsibility (DTE, or CSU.
OBJECT-TYPE    
  INTEGER cylinkOnesResponsibilityDTE(0), cylinkOnesResponsibilityACSU(1)  

cylinkOnesControl 1.3.6.1.4.1.2.6.2.3.1.3.1.9
The Ones Density Control selected (LSB 24, D4 FRM, or ESF DL).
OBJECT-TYPE    
  INTEGER cylinkOnesControlLSB24(0), cylinkOnesControlD4FRM(1), cylinkOnesControlESFDL(2)  

cylinkZeroProtection 1.3.6.1.4.1.2.6.2.3.1.3.1.10
The Consecutive Zero Control selected (15, or 80). This determines the the maximum number of consecutive zeros allowed in the data stream before a one is forced.
OBJECT-TYPE    
  INTEGER cylinkZeroProtection80(0), cylinkZeroProtection15(1)  

cylinkClockSource 1.3.6.1.4.1.2.6.2.3.1.3.1.11
The transmit clock source selected for NRZ DIUs (network, DTE, an external clock, or the CSU's internal clock).
OBJECT-TYPE    
  INTEGER cylinkClockSourceNetwork(0), cylinkClockSourceDTE(1), cylinkClockSourceExternal(2), cylinkClockSourceInternal(3)  

cylinkClockFrequency 1.3.6.1.4.1.2.6.2.3.1.3.1.12
The external clock frequency selected (56 kHz, 256 kHz, 1.344 MHz, 1.544 MHz).
OBJECT-TYPE    
  INTEGER cylinkClockFreq-56kHz(0), cylinkClockFreq-256kHz(1), cylinkClockFreq-1-344MHz(2), cylinkClockFreq-1-544MHz(3)  

cylinkClockBackup 1.3.6.1.4.1.2.6.2.3.1.3.1.13
The transmit clock backup source selected for NRZ DIUs (network, DTE, an external clock, or the CSU's internal clock).
OBJECT-TYPE    
  INTEGER cylinkClockBackupNetwork(0), cylinkClockBackupDTE(1), cylinkClockBackupExternal(2), cylinkClockBackupInternal(3)  

cylinkDIUFrequency 1.3.6.1.4.1.2.6.2.3.1.3.1.14
The DIU frequency selected for NRZ DIUs (767 kbps, 1.244 Mbps, 1.528 Mbps, 1.536 Mbps).
OBJECT-TYPE    
  INTEGER cylinkDIUFreq-768kbps(0), cylinkDIUFreq-1-344Mbps(1), cylinkDIUFreq-1-528Mbps(2), cylinkDIUFreq-1-536Mbps(3)  

cylinkDIUTiming 1.3.6.1.4.1.2.6.2.3.1.3.1.15
The DIU transmit timing selected for NRZ DIUs (Send Timing, or Terminal Timing).
OBJECT-TYPE    
  INTEGER cylinkDIUTimingTT(0), cylinkDIUTimingST(1)  

cylinkDialoutCapability 1.3.6.1.4.1.2.6.2.3.1.3.1.16
The DIU dial-out capability selected (polled, tone, or pulse).
OBJECT-TYPE    
  INTEGER cylinkDialoutCapabilityPolled(0), cylinkDialoutCapabilityTone(1), cylinkDialoutCapabilityPulse(2)  

cylinkDialoutHoldoff 1.3.6.1.4.1.2.6.2.3.1.3.1.17
The mininum time, in minutes, between successful CSU-to-NMS connections to report alarm conditions.
OBJECT-TYPE    
  INTEGER 1..99  

cylinkPrimaryPhone 1.3.6.1.4.1.2.6.2.3.1.3.1.18
The primary telephone number used by by the CSU to contact the NMS.
OBJECT-TYPE    
  DisplayString SIZE(0..19)  

cylinkSecondaryPhone 1.3.6.1.4.1.2.6.2.3.1.3.1.19
The secondary telephone number used by by the CSU to contact the NMS.
OBJECT-TYPE    
  DisplayString SIZE(0..19)  

cylinkAlarmRepeatTime 1.3.6.1.4.1.2.6.2.3.1.3.1.20
The interval, in minutes, that the CSU will insert duplicate messages in the alarm queue for persistant alarm conditions.
OBJECT-TYPE    
  INTEGER 1..99  

cylinkESThreshold 1.3.6.1.4.1.2.6.2.3.1.3.1.21
The threshold, in seconds, for the errored second value in the current 15-minute interval.
OBJECT-TYPE    
  INTEGER 1..99  

cylinkSecondaryContact 1.3.6.1.4.1.2.6.2.3.1.3.1.22
The state of the CSU secondary contact (open or closed).
OBJECT-TYPE    
  INTEGER cylinkSecondaryContactOpen(0), cylinkSecondaryContactClosed(1)  

ibmsystem 1.3.6.1.4.1.2.6.2.4
OBJECT IDENTIFIER    

ibmMainProcessorLoadTable 1.3.6.1.4.1.2.6.2.4.1
A table containing the average main processor load over each minute for the last 60 minutes.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmMainProcessorLoadEntry

ibmMainProcessorLoadEntry 1.3.6.1.4.1.2.6.2.4.1.1
An entry in the main processor load table.
OBJECT-TYPE    
  IbmMainProcessorLoadEntry  

ibmMainProcessorLoadIndex 1.3.6.1.4.1.2.6.2.4.1.1.1
Indicates the number of minutes ago that this entry contains main processor load information for.
OBJECT-TYPE    
  INTEGER 1..60  

ibmMainProcessorLoad 1.3.6.1.4.1.2.6.2.4.1.1.2
The main processor load averaged over one minute. The load is given as a percentage. For example, 25% is 25.
OBJECT-TYPE    
  Gauge  

ibmswvpd 1.3.6.1.4.1.2.6.2.4.2
OBJECT IDENTIFIER    

swVpdTable 1.3.6.1.4.1.2.6.2.4.2.1
A table containing software vital product data information.
OBJECT-TYPE    
  SEQUENCE OF  
    SwVpdEntry

swVpdEntry 1.3.6.1.4.1.2.6.2.4.2.1.1
An entry for a piece of software installed on this router.
OBJECT-TYPE    
  SwVpdEntry  

swvpdIndex 1.3.6.1.4.1.2.6.2.4.2.1.1.1
A unique value for each entry in this table.
OBJECT-TYPE    
  INTEGER  

swvpdName 1.3.6.1.4.1.2.6.2.4.2.1.1.2
The name of this software product.
OBJECT-TYPE    
  DisplayString  

swvpdPtfName 1.3.6.1.4.1.2.6.2.4.2.1.1.3
If this entry represents a PTF, this object contains the name of the PTF. Otherwise this object contains a string of zero length.
OBJECT-TYPE    
  DisplayString  

swvpdVerId 1.3.6.1.4.1.2.6.2.4.2.1.1.4
The version identifier for this piece of software.
OBJECT-TYPE    
  INTEGER  

swvpdRelId 1.3.6.1.4.1.2.6.2.4.2.1.1.5
The release identifier for this piece of software.
OBJECT-TYPE    
  INTEGER  

swvpdModId 1.3.6.1.4.1.2.6.2.4.2.1.1.6
The modification level identifier for this piece of software.
OBJECT-TYPE    
  INTEGER  

swvpdFixId 1.3.6.1.4.1.2.6.2.4.2.1.1.7
The fix level identifier for this piece of software.
OBJECT-TYPE    
  INTEGER  

swvpdState 1.3.6.1.4.1.2.6.2.4.2.1.1.8
The state of the action in swvpdAction being performed on this software.
OBJECT-TYPE    
  INTEGER complete(1), pending(2), broken(3), cancelled(4), unknown(5)  

swvpdAction 1.3.6.1.4.1.2.6.2.4.2.1.1.9
The action being performed on this software.
OBJECT-TYPE    
  INTEGER apply(1), commit(2), reject(3), decommit(4), cleanup(5), unknown(6)  

swvpdPath 1.3.6.1.4.1.2.6.2.4.2.1.1.10
An indication of which part of the system this software is installed on. The values correspond to the following paths: root(1) /etc/objrepos usr(2) /usr/lib/objrepos share(3) /usr/share/lib/objrepos
OBJECT-TYPE    
  INTEGER root(1), usr(2), share(3)  

swvpdDateTime 1.3.6.1.4.1.2.6.2.4.2.1.1.11
A string indicating the date and time that the action in swvpdAction was performed on this software.
OBJECT-TYPE    
  DisplayString  

ibmmaint 1.3.6.1.4.1.2.6.2.4.4
OBJECT IDENTIFIER    

ibmmaintShutdown 1.3.6.1.4.1.2.6.2.4.4.1
When read, an active 6611 will return the value running(1). To force a shutdown, without a subsequent re-ipl of the 6611, this value should be set to shutdown-noipl(2). To recyle the 6611, (i.e.- shutdown with a subsequent re-ipl), and use the currently installed configuration, this variable should be set to shutdown-ipl-local(4).
OBJECT-TYPE    
  INTEGER running(1), shutdown-noipl(2), shutdown-ipl-local(4)  

ibmicmp 1.3.6.1.4.1.2.6.2.5
OBJECT IDENTIFIER    

ibmsnmp 1.3.6.1.4.1.2.6.2.6
OBJECT IDENTIFIER    

ibmTrapNum 1.3.6.1.4.1.2.6.2.6.1
Number of IBM enterprise specific traps generated by this node.
OBJECT-TYPE    
  Counter  

ibmTrapThrottleCount 1.3.6.1.4.1.2.6.2.6.2
Number of traps throttled since last trap.
OBJECT-TYPE    
  Counter  

ibmTrapThrottleId 1.3.6.1.4.1.2.6.2.6.3
Trap ID of throttled traps. All throttled traps counted by ibmTrapThrottleCount have the this ID.
OBJECT-TYPE    
  INTEGER  

ibmTrapThrottleTime 1.3.6.1.4.1.2.6.2.6.4
Number of seconds which must separate consecutive enterprise-specific traps with identical ID in order to not throttle them. If the value of this object is 0, then trap throttling is inactive.
OBJECT-TYPE    
  INTEGER  

ibmbridge 1.3.6.1.4.1.2.6.2.7
OBJECT IDENTIFIER    

ibmbridgeMACAddressFilters 1.3.6.1.4.1.2.6.2.7.1
OBJECT IDENTIFIER    

ibmmacAddrFilterInfoTable 1.3.6.1.4.1.2.6.2.7.1.1
Table of MAC address filtering information.
OBJECT-TYPE    
  SEQUENCE OF  
    MacAddrFilterInfoEntry

ibmmacAddrFilterInfoEntry 1.3.6.1.4.1.2.6.2.7.1.1.1
MAC address filtering information for a single interface.
OBJECT-TYPE    
  MacAddrFilterInfoEntry  

ibmmacAddrFilterIfIndex 1.3.6.1.4.1.2.6.2.7.1.1.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmmacAddrFilterInBcastType 1.3.6.1.4.1.2.6.2.7.1.1.1.2
For the incoming MAC address filter table, determines what type of frames will be filtered.
OBJECT-TYPE    
  INTEGER filterARB(1), filterSRB(2), filterBoth(3)  

ibmmacAddrFilterOutBcastType 1.3.6.1.4.1.2.6.2.7.1.1.1.3
For the outgoing MAC address filter table, determines what type of frames will be filtered.
OBJECT-TYPE    
  INTEGER filterARB(1), filterSRB(2), filterBoth(3)  

ibmmacAddrFilterInFilterType 1.3.6.1.4.1.2.6.2.7.1.1.1.4
For the incoming filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmmacAddrFilterOutFilterType 1.3.6.1.4.1.2.6.2.7.1.1.1.5
For the outgoing filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmmacAddrFilterInNotForwarded 1.3.6.1.4.1.2.6.2.7.1.1.1.6
Number of packets not forwarded, in the incoming direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmmacAddrFilterOutNotForwarded 1.3.6.1.4.1.2.6.2.7.1.1.1.7
Number of packets not forwarded, in the outgoing direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmmacAddrFilterType 1.3.6.1.4.1.2.6.2.7.1.1.1.8
The type of entry, either sr or tb.
OBJECT-TYPE    
  INTEGER sr(1), tb(2)  

ibmmacAddrFilterInTable 1.3.6.1.4.1.2.6.2.7.1.2
Table of MAC address filtering information for incoming frames.
OBJECT-TYPE    
  SEQUENCE OF  
    MacAddrFilterInEntry

ibmmacAddrFilterInEntry 1.3.6.1.4.1.2.6.2.7.1.2.1
Filtering information for incoming frames.
OBJECT-TYPE    
  MacAddrFilterInEntry  

ibmmacAddrFilterInIfIndex 1.3.6.1.4.1.2.6.2.7.1.2.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmmacAddrFilterInSrcAddress 1.3.6.1.4.1.2.6.2.7.1.2.1.2
MAC source address to be filtered.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmmacAddrFilterInSrcMask 1.3.6.1.4.1.2.6.2.7.1.2.1.3
Mask to allow ibmmacAddrFilterInSrcAddress to be used as a range of values.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmmacAddrFilterInDestAddress 1.3.6.1.4.1.2.6.2.7.1.2.1.4
MAC destination address to be filtered.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmmacAddrFilterInDestMask 1.3.6.1.4.1.2.6.2.7.1.2.1.5
Mask to allow ibmmacAddrFilterInDestAddress to be used as a range of values.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmmacAddrFilterInType 1.3.6.1.4.1.2.6.2.7.1.2.1.6
The type of entry, either sr or tb.
OBJECT-TYPE    
  INTEGER sr(1), tb(2)  

ibmmacAddrFilterOutTable 1.3.6.1.4.1.2.6.2.7.1.3
Table of MAC address filtering information for outgoing frames.
OBJECT-TYPE    
  SEQUENCE OF  
    MacAddrFilterOutEntry

ibmmacAddrFilterOutEntry 1.3.6.1.4.1.2.6.2.7.1.3.1
Filtering information for outgoing frames.
OBJECT-TYPE    
  MacAddrFilterOutEntry  

ibmmacAddrFilterOutIfIndex 1.3.6.1.4.1.2.6.2.7.1.3.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmmacAddrFilterOutSrcAddress 1.3.6.1.4.1.2.6.2.7.1.3.1.2
MAC source address to be filtered.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmmacAddrFilterOutSrcMask 1.3.6.1.4.1.2.6.2.7.1.3.1.3
Mask to allow ibmmacAddrFilterOutSrcAddress to be used as a range of values.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmmacAddrFilterOutDestAddress 1.3.6.1.4.1.2.6.2.7.1.3.1.4
MAC destination address to be filtered.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmmacAddrFilterOutDestMask 1.3.6.1.4.1.2.6.2.7.1.3.1.5
Mask to allow ibmmacAddrFilterOutDestAddress to be used as a range of values.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmmacAddrFilterOutType 1.3.6.1.4.1.2.6.2.7.1.3.1.6
Type type of entry either sr or tb
OBJECT-TYPE    
  INTEGER sr(1), tb(2)  

ibmbridgeSAPFilters 1.3.6.1.4.1.2.6.2.7.2
OBJECT IDENTIFIER    

ibmsapFilterInfoTable 1.3.6.1.4.1.2.6.2.7.2.1
Table of SAP filtering information.
OBJECT-TYPE    
  SEQUENCE OF  
    SapFilterInfoEntry

ibmsapFilterInfoEntry 1.3.6.1.4.1.2.6.2.7.2.1.1
SAP filtering information for a single interface.
OBJECT-TYPE    
  SapFilterInfoEntry  

ibmsapFilterIfIndex 1.3.6.1.4.1.2.6.2.7.2.1.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmsapFilterInBcastType 1.3.6.1.4.1.2.6.2.7.2.1.1.2
For the incoming SAP filter table, determines what type of frames will be filtered.
OBJECT-TYPE    
  INTEGER filterARB(1), filterSRB(2), filterBoth(3)  

ibmsapFilterOutBcastType 1.3.6.1.4.1.2.6.2.7.2.1.1.3
For the outgoing SAP filter table, determines what type of frames will be filtered.
OBJECT-TYPE    
  INTEGER filterARB(1), filterSRB(2), filterBoth(3)  

ibmsapFilterIn 1.3.6.1.4.1.2.6.2.7.2.1.1.4
A bitmap of all possible source SAPs (even) that will be on or off depending on whether or not an incoming frame with that SAP is to be forwarded.
OBJECT-TYPE    
  OCTET STRING SIZE(16)  

ibmsapFilterOut 1.3.6.1.4.1.2.6.2.7.2.1.1.5
A bitmap of all possible source SAPs (even) that will be on or off depending on whether or not an outgoing frame with that SAP is to be forwarded.
OBJECT-TYPE    
  OCTET STRING SIZE(16)  

ibmsapFilterInNotForwarded 1.3.6.1.4.1.2.6.2.7.2.1.1.6
Number of packets not forwarded, in the incoming direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmsapFilterOutNotForwarded 1.3.6.1.4.1.2.6.2.7.2.1.1.7
Number of packets not forwarded, in the outgoing direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmsapFilterType 1.3.6.1.4.1.2.6.2.7.2.1.1.8
The type of entry, either sr or tb.
OBJECT-TYPE    
  INTEGER sr(1), tb(2)  

ibmbridgeSNAPFilters 1.3.6.1.4.1.2.6.2.7.3
OBJECT IDENTIFIER    

ibmsnapFilterInfoTable 1.3.6.1.4.1.2.6.2.7.3.1
Table of SNAP filtering information. Note that SNAP filtering only comes into play if packets with source SAP 0xAA are being forwarded.
OBJECT-TYPE    
  SEQUENCE OF  
    SnapFilterInfoEntry

ibmsnapFilterInfoEntry 1.3.6.1.4.1.2.6.2.7.3.1.1
SNAP filtering information for a single interface.
OBJECT-TYPE    
  SnapFilterInfoEntry  

ibmsnapFilterIfIndex 1.3.6.1.4.1.2.6.2.7.3.1.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmsnapFilterInFilterType 1.3.6.1.4.1.2.6.2.7.3.1.1.2
For the incoming SNAP filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmsnapFilterOutFilterType 1.3.6.1.4.1.2.6.2.7.3.1.1.3
For the outgoing SNAP filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmsnapFilterInNotForwarded 1.3.6.1.4.1.2.6.2.7.3.1.1.4
Number of packets not forwarded, in the incoming direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmsnapFilterOutNotForwarded 1.3.6.1.4.1.2.6.2.7.3.1.1.5
Number of packets not forwarded, in the outgoing direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmsnapFilterType 1.3.6.1.4.1.2.6.2.7.3.1.1.6
The type of entry, either sr or tb.
OBJECT-TYPE    
  INTEGER sr(1), tb(2)  

ibmsnapFilterInTable 1.3.6.1.4.1.2.6.2.7.3.2
Table of SNAP type filtering information for incoming frames. Note that the entries in this table only come into play if packets with source SAP 0xAA are being forwarded.
OBJECT-TYPE    
  SEQUENCE OF  
    SnapFilterInEntry

ibmsnapFilterInEntry 1.3.6.1.4.1.2.6.2.7.3.2.1
Filtering information for a single SNAP value on a single interface.
OBJECT-TYPE    
  SnapFilterInEntry  

ibmsnapFilterInIfIndex 1.3.6.1.4.1.2.6.2.7.3.2.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmsnapFilterInValue 1.3.6.1.4.1.2.6.2.7.3.2.1.2
Indicates which SNAP value to filter.
OBJECT-TYPE    
  INTEGER  

ibmsnapFilterInMask 1.3.6.1.4.1.2.6.2.7.3.2.1.3
Mask to allow ibmsnapFilterInValue to be used as a range of values.
OBJECT-TYPE    
  INTEGER  

ibmsnapFilterInType 1.3.6.1.4.1.2.6.2.7.3.2.1.4
The type of entry, either sr or tb.
OBJECT-TYPE    
  INTEGER sr(1), tb(2)  

ibmsnapFilterOutTable 1.3.6.1.4.1.2.6.2.7.3.3
Table of SNAP filtering information for outgoing frames. Note that the entries in this table only come into play if packets with source SAP 0xAA are being forwarded.
OBJECT-TYPE    
  SEQUENCE OF  
    SnapFilterOutEntry

ibmsnapFilterOutEntry 1.3.6.1.4.1.2.6.2.7.3.3.1
Filtering information for a single SNAP value on a single interface.
OBJECT-TYPE    
  SnapFilterOutEntry  

ibmsnapFilterOutIfIndex 1.3.6.1.4.1.2.6.2.7.3.3.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmsnapFilterOutValue 1.3.6.1.4.1.2.6.2.7.3.3.1.2
Indicates which SNAP values to filter.
OBJECT-TYPE    
  INTEGER  

ibmsnapFilterOutMask 1.3.6.1.4.1.2.6.2.7.3.3.1.3
Mask to allow ibmsnapFilterOutValue to be used as a range of values.
OBJECT-TYPE    
  INTEGER  

ibmsnapFilterOutType 1.3.6.1.4.1.2.6.2.7.3.3.1.4
The type of entry, either sr or tb.
OBJECT-TYPE    
  INTEGER sr(1), tb(2)  

ibmbridgeRingFilters 1.3.6.1.4.1.2.6.2.7.4
OBJECT IDENTIFIER    

ibmringFilterInfoTable 1.3.6.1.4.1.2.6.2.7.4.1
Table of ring filtering information.
OBJECT-TYPE    
  SEQUENCE OF  
    RingFilterInfoEntry

ibmringFilterInfoEntry 1.3.6.1.4.1.2.6.2.7.4.1.1
Ring filtering information for a single interface.
OBJECT-TYPE    
  RingFilterInfoEntry  

ibmringFilterIfIndex 1.3.6.1.4.1.2.6.2.7.4.1.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmringFilterInBcastType 1.3.6.1.4.1.2.6.2.7.4.1.1.2
For the incoming ring filter table, determines what type of frames will be filtered.
OBJECT-TYPE    
  INTEGER filterARB(1), filterSRB(2), filterBoth(3)  

ibmringFilterOutBcastType 1.3.6.1.4.1.2.6.2.7.4.1.1.3
For the outgoing ring filter table, determines what type of frames will be filtered.
OBJECT-TYPE    
  INTEGER filterARB(1), filterSRB(2), filterBoth(3)  

ibmringFilterInFilterType 1.3.6.1.4.1.2.6.2.7.4.1.1.4
For the incoming ring filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmringFilterOutFilterType 1.3.6.1.4.1.2.6.2.7.4.1.1.5
For the outgoing ring filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmringFilterInNotForwarded 1.3.6.1.4.1.2.6.2.7.4.1.1.6
Number of packets not forwarded, in the incoming direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmringFilterOutNotForwarded 1.3.6.1.4.1.2.6.2.7.4.1.1.7
Number of packets not forwarded, in the outgoing direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmringFilterInTable 1.3.6.1.4.1.2.6.2.7.4.2
Table of ring number filtering information for incoming frames.
OBJECT-TYPE    
  SEQUENCE OF  
    RingFilterInEntry

ibmringFilterInEntry 1.3.6.1.4.1.2.6.2.7.4.2.1
Filtering information for a single ring number on a single interface.
OBJECT-TYPE    
  RingFilterInEntry  

ibmringFilterInIfIndex 1.3.6.1.4.1.2.6.2.7.4.2.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmringFilterInNumber 1.3.6.1.4.1.2.6.2.7.4.2.1.2
Indicates which ring number to filter.
OBJECT-TYPE    
  INTEGER  

ibmringFilterInMask 1.3.6.1.4.1.2.6.2.7.4.2.1.3
Mask to allow ibmringFilterInNumber to be used as a range of values.
OBJECT-TYPE    
  INTEGER  

ibmringFilterOutTable 1.3.6.1.4.1.2.6.2.7.4.3
Table of ring number filtering information for outgoing frames.
OBJECT-TYPE    
  SEQUENCE OF  
    RingFilterOutEntry

ibmringFilterOutEntry 1.3.6.1.4.1.2.6.2.7.4.3.1
Filtering information for a single ring number on a single interface.
OBJECT-TYPE    
  RingFilterOutEntry  

ibmringFilterOutIfIndex 1.3.6.1.4.1.2.6.2.7.4.3.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmringFilterOutNumber 1.3.6.1.4.1.2.6.2.7.4.3.1.2
Indicates which ring number to filter.
OBJECT-TYPE    
  INTEGER  

ibmringFilterOutMask 1.3.6.1.4.1.2.6.2.7.4.3.1.3
Mask to allow ibmringFilterOutNumber to be used as a range of values.
OBJECT-TYPE    
  INTEGER  

ibmbridgeHopCountFilters 1.3.6.1.4.1.2.6.2.7.5
OBJECT IDENTIFIER    

ibmhopCountFilterInfoTable 1.3.6.1.4.1.2.6.2.7.5.1
Table of hop count filtering information.
OBJECT-TYPE    
  SEQUENCE OF  
    HopCountFilterInfoEntry

ibmhopCountFilterInfoEntry 1.3.6.1.4.1.2.6.2.7.5.1.1
Hop count filtering information for a single interface.
OBJECT-TYPE    
  HopCountFilterInfoEntry  

ibmhopCountFilterIfIndex 1.3.6.1.4.1.2.6.2.7.5.1.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmhopCountFilterBcastType 1.3.6.1.4.1.2.6.2.7.5.1.1.2
Determines what type of incoming frames will be filtered.
OBJECT-TYPE    
  INTEGER filterARB(1), filterSRB(2), filterBoth(3)  

ibmhopCountFilterCount 1.3.6.1.4.1.2.6.2.7.5.1.1.3
The number of hops allowed for incoming frames.
OBJECT-TYPE    
  INTEGER  

ibmbridgeWindowFilters 1.3.6.1.4.1.2.6.2.7.6
OBJECT IDENTIFIER    

ibmwindowFilterInfoTable 1.3.6.1.4.1.2.6.2.7.6.1
Table of Window filtering information.
OBJECT-TYPE    
  SEQUENCE OF  
    WindowFilterInfoEntry

ibmwindowFilterInfoEntry 1.3.6.1.4.1.2.6.2.7.6.1.1
Window filtering information for a single interface.
OBJECT-TYPE    
  WindowFilterInfoEntry  

ibmwindowFilterIfIndex 1.3.6.1.4.1.2.6.2.7.6.1.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmwindowFilterInBcastType 1.3.6.1.4.1.2.6.2.7.6.1.1.2
For the incoming Window filter table, determines what type of frames will be filtered.
OBJECT-TYPE    
  INTEGER filterARB(1), filterSRB(2), filterBoth(3)  

ibmwindowFilterOutBcastType 1.3.6.1.4.1.2.6.2.7.6.1.1.3
For the outgoing Window filter table, determines what type of frames will be filtered.
OBJECT-TYPE    
  INTEGER filterARB(1), filterSRB(2), filterBoth(3)  

ibmwindowFilterInFilterType 1.3.6.1.4.1.2.6.2.7.6.1.1.4
For the incoming filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmwindowFilterOutFilterType 1.3.6.1.4.1.2.6.2.7.6.1.1.5
For the outgoing filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmwindowFilterInNotForwarded 1.3.6.1.4.1.2.6.2.7.6.1.1.6
Number of packets not forwarded, in the incoming direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmwindowFilterOutNotForwarded 1.3.6.1.4.1.2.6.2.7.6.1.1.7
Number of packets not forwarded, in the outgoing direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmwindowFilterType 1.3.6.1.4.1.2.6.2.7.6.1.1.8
The type of entry, either sr or tb.
OBJECT-TYPE    
  INTEGER sr(1), tb(2)  

ibmwindowFilterInTable 1.3.6.1.4.1.2.6.2.7.6.2
Table of Window filtering information for incoming frames.
OBJECT-TYPE    
  SEQUENCE OF  
    WindowFilterInEntry

ibmwindowFilterInEntry 1.3.6.1.4.1.2.6.2.7.6.2.1
Filtering information for incoming frames.
OBJECT-TYPE    
  WindowFilterInEntry  

ibmwindowFilterInIfIndex 1.3.6.1.4.1.2.6.2.7.6.2.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmwindowFilterInContents 1.3.6.1.4.1.2.6.2.7.6.2.1.2
String of bytes that will be compared with bytes in the frame.
OBJECT-TYPE    
  OCTET STRING  

ibmwindowFilterInMaskString 1.3.6.1.4.1.2.6.2.7.6.2.1.3
String of bytes that will be masked with bytes in the contents field.
OBJECT-TYPE    
  OCTET STRING  

ibmwindowFilterInOffsetStart 1.3.6.1.4.1.2.6.2.7.6.2.1.4
Determines the starting point where the contents field should be applied. A value of 'MAC' means the base is at the beginning of the destination MAC address field, whereas, a value of 'SAP' means it is applied at the beginning of the destination SAP field.
OBJECT-TYPE    
  DisplayString  

ibmwindowFilterInNumBytes 1.3.6.1.4.1.2.6.2.7.6.2.1.5
Number of bytes in the contents field that are used for filtering.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ibmwindowFilterInOffset 1.3.6.1.4.1.2.6.2.7.6.2.1.6
Number of bytes offset into the frame from the offset start point to begin the compare.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmwindowFilterInId 1.3.6.1.4.1.2.6.2.7.6.2.1.7
A unique identifier associated with this window filter entry.
OBJECT-TYPE    
  INTEGER  

ibmwindowFilterInType 1.3.6.1.4.1.2.6.2.7.6.2.1.8
The type of entry, either sr or tb.
OBJECT-TYPE    
  INTEGER sr(1), tb(2)  

ibmwindowFilterOutTable 1.3.6.1.4.1.2.6.2.7.6.3
Table of Window filtering information for outgoing frames.
OBJECT-TYPE    
  SEQUENCE OF  
    WindowFilterOutEntry

ibmwindowFilterOutEntry 1.3.6.1.4.1.2.6.2.7.6.3.1
Filtering information for outgoing frames.
OBJECT-TYPE    
  WindowFilterOutEntry  

ibmwindowFilterOutIfIndex 1.3.6.1.4.1.2.6.2.7.6.3.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmwindowFilterOutContents 1.3.6.1.4.1.2.6.2.7.6.3.1.2
String of bytes that will be compared with bytes in the frame.
OBJECT-TYPE    
  OCTET STRING  

ibmwindowFilterOutMaskString 1.3.6.1.4.1.2.6.2.7.6.3.1.3
String of bytes that will be masked with bytes in the contents field.
OBJECT-TYPE    
  OCTET STRING  

ibmwindowFilterOutOffsetStart 1.3.6.1.4.1.2.6.2.7.6.3.1.4
Determines the starting point where the contents field should be applied. A value of 'MAC' means the base is at the beginning of the destination MAC address field, whereas, a value of 'SAP' means it is applied at the beginning of the destination SAP field.
OBJECT-TYPE    
  DisplayString  

ibmwindowFilterOutNumBytes 1.3.6.1.4.1.2.6.2.7.6.3.1.5
Number of bytes in the contents field that are used for filtering.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ibmwindowFilterOutOffset 1.3.6.1.4.1.2.6.2.7.6.3.1.6
Number of bytes offset into the frame from the offset start point to begin the compare.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmwindowFilterOutId 1.3.6.1.4.1.2.6.2.7.6.3.1.7
A unique identifier associated with this window filter entry.
OBJECT-TYPE    
  INTEGER  

ibmwindowFilterOutType 1.3.6.1.4.1.2.6.2.7.6.3.1.8
The type of entry, either sr or tb.
OBJECT-TYPE    
  INTEGER sr(1), tb(2)  

ibmbridgeFiltOrderTable 1.3.6.1.4.1.2.6.2.7.7
OBJECT IDENTIFIER    

ibmFiltOrderInTable 1.3.6.1.4.1.2.6.2.7.7.1
Table of information describing which order the filters are applied for incoming frames.
OBJECT-TYPE    
  SEQUENCE OF  
    FiltOrderInEntry

ibmFiltOrderInEntry 1.3.6.1.4.1.2.6.2.7.7.1.1
Filter order information for incoming frames.
OBJECT-TYPE    
  FiltOrderInEntry  

ibmFiltOrderInIfIndex 1.3.6.1.4.1.2.6.2.7.7.1.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmFiltOrderInPriority 1.3.6.1.4.1.2.6.2.7.7.1.1.2
The priority of when a filter is applied to an incoming frame. A value of 1 signifies that it is applied first.
OBJECT-TYPE    
  INTEGER  

ibmFiltOrderInName 1.3.6.1.4.1.2.6.2.7.7.1.1.3
The name of the filter applied to incoming frames that is associated with the priority, ibmFiltOrderInPriority.
OBJECT-TYPE    
  DisplayString  

ibmFiltOrderInType 1.3.6.1.4.1.2.6.2.7.7.1.1.4
The type of entry, either sr or tb.
OBJECT-TYPE    
  INTEGER sr(1), tb(2)  

ibmFiltOrderOutTable 1.3.6.1.4.1.2.6.2.7.7.2
Table of information describing which order the filters are applied for outgoing frames.
OBJECT-TYPE    
  SEQUENCE OF  
    FiltOrderOutEntry

ibmFiltOrderOutEntry 1.3.6.1.4.1.2.6.2.7.7.2.1
Filter order information for outgoing frames.
OBJECT-TYPE    
  FiltOrderOutEntry  

ibmFiltOrderOutIfIndex 1.3.6.1.4.1.2.6.2.7.7.2.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmFiltOrderOutPriority 1.3.6.1.4.1.2.6.2.7.7.2.1.2
The priority of when a filter is applied to an outgoing frame. A value of 1 signifies that it is applied first.
OBJECT-TYPE    
  INTEGER  

ibmFiltOrderOutName 1.3.6.1.4.1.2.6.2.7.7.2.1.3
The name of the filter applied to outgoing frames that is associated with the priority, ibmFiltOrderOutPriority.
OBJECT-TYPE    
  DisplayString  

ibmFiltOrderOutType 1.3.6.1.4.1.2.6.2.7.7.2.1.4
The type of entry, either sr or tb.
OBJECT-TYPE    
  INTEGER sr(1), tb(2)  

ibmbridgeRIFFilters 1.3.6.1.4.1.2.6.2.7.8
OBJECT IDENTIFIER    

ibmRIFFilterInfoTable 1.3.6.1.4.1.2.6.2.7.8.1
Table of routing information field filtering information.
OBJECT-TYPE    
  SEQUENCE OF  
    RIFFilterInfoEntry

ibmRIFFilterInfoEntry 1.3.6.1.4.1.2.6.2.7.8.1.1
Routing information field filtering information for a single interface.
OBJECT-TYPE    
  RIFFilterInfoEntry  

ibmRIFFilterIfIndex 1.3.6.1.4.1.2.6.2.7.8.1.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmRIFFilterInBcastType 1.3.6.1.4.1.2.6.2.7.8.1.1.2
For the incoming routing information field filter table, determines what type of frames will be filtered.
OBJECT-TYPE    
  INTEGER filterARB(1), filterSRB(2), filterBoth(3)  

ibmRIFFilterOutBcastType 1.3.6.1.4.1.2.6.2.7.8.1.1.3
For the outgoing routing information field filter table, determines what type of frames will be filtered.
OBJECT-TYPE    
  INTEGER filterARB(1), filterSRB(2), filterBoth(3)  

ibmRIFFilterInFilterType 1.3.6.1.4.1.2.6.2.7.8.1.1.4
For the incoming routing information filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmRIFFilterOutFilterType 1.3.6.1.4.1.2.6.2.7.8.1.1.5
For the outgoing routing information field filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmRIFFilterInNotForwarded 1.3.6.1.4.1.2.6.2.7.8.1.1.6
Number of packets not forwarded, in the incoming direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmRIFFilterOutNotForwarded 1.3.6.1.4.1.2.6.2.7.8.1.1.7
Number of packets not forwarded, in the outgoing direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmRIFFilterInTable 1.3.6.1.4.1.2.6.2.7.8.2
Table of routing information field filtering information for incoming frames.
OBJECT-TYPE    
  SEQUENCE OF  
    RIFFilterInEntry

ibmRIFFilterInEntry 1.3.6.1.4.1.2.6.2.7.8.2.1
Filtering information for a single routing information field on a single interface.
OBJECT-TYPE    
  RIFFilterInEntry  

ibmRIFFilterInIfIndex 1.3.6.1.4.1.2.6.2.7.8.2.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmRIFFilterInRingNumber 1.3.6.1.4.1.2.6.2.7.8.2.1.2
Indicates which ring number to filter.
OBJECT-TYPE    
  INTEGER  

ibmRIFFilterInRingMask 1.3.6.1.4.1.2.6.2.7.8.2.1.3
Mask to allow ibmRIFFilterInRingNumber to be used as a range of values.
OBJECT-TYPE    
  INTEGER  

ibmRIFFilterInBridgeNumber 1.3.6.1.4.1.2.6.2.7.8.2.1.4
Indicates which bridge number to filter.
OBJECT-TYPE    
  INTEGER  

ibmRIFFilterInBridgeMask 1.3.6.1.4.1.2.6.2.7.8.2.1.5
Mask to allow ibmRIFFilterInBridgeNumber to be used as a range of values.
OBJECT-TYPE    
  INTEGER  

ibmRIFFilterInRouteDesignator 1.3.6.1.4.1.2.6.2.7.8.2.1.6
Indicates which route designators in the routing information field are to be used for filtering.
OBJECT-TYPE    
  INTEGER firstroutedesignator(1), nexttolastroutedesignator(2), allroutedesignators(3)  

ibmRIFFilterOutTable 1.3.6.1.4.1.2.6.2.7.8.3
Table of routing information field filtering information for outgoing frames.
OBJECT-TYPE    
  SEQUENCE OF  
    RIFFilterOutEntry

ibmRIFFilterOutEntry 1.3.6.1.4.1.2.6.2.7.8.3.1
Filtering information for a single routing information field on a single interface.
OBJECT-TYPE    
  RIFFilterOutEntry  

ibmRIFFilterOutIfIndex 1.3.6.1.4.1.2.6.2.7.8.3.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmRIFFilterOutRingNumber 1.3.6.1.4.1.2.6.2.7.8.3.1.2
Indicates which ring number to filter.
OBJECT-TYPE    
  INTEGER  

ibmRIFFilterOutRingMask 1.3.6.1.4.1.2.6.2.7.8.3.1.3
Mask to allow ibmRIFFilterOutRingNumber to be used as a range of values.
OBJECT-TYPE    
  INTEGER  

ibmRIFFilterOutBridgeNumber 1.3.6.1.4.1.2.6.2.7.8.3.1.4
Indicates which bridge number to filter.
OBJECT-TYPE    
  INTEGER  

ibmRIFFilterOutBridgeMask 1.3.6.1.4.1.2.6.2.7.8.3.1.5
Mask to allow ibmRIFFilterOutBridgeNumber to be used as a range of values.
OBJECT-TYPE    
  INTEGER  

ibmRIFFilterOutRouteDesignator 1.3.6.1.4.1.2.6.2.7.8.3.1.6
Indicates which route designators in the routing information field are to be used for filtering.
OBJECT-TYPE    
  INTEGER firstroutedesignator(1), nexttolastroutedesignator(2), allroutedesignators(3)  

ibmfr 1.3.6.1.4.1.2.6.2.8
OBJECT IDENTIFIER    

ibmfrDlcmiTable 1.3.6.1.4.1.2.6.2.8.1
The Parameters for the Data Link Connection Management Interface corresponding to any given ifEntry.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmfrDlcmiEntry

ibmfrDlcmiEntry 1.3.6.1.4.1.2.6.2.8.1.1
The Parameters for the Data Link Connection Management Interface.
OBJECT-TYPE    
  IbmfrDlcmiEntry  

ibmfrDlcmiIfIndex 1.3.6.1.4.1.2.6.2.8.1.1.1
The ifIndex value of the corresponding ifEn- try.
OBJECT-TYPE    
  INTEGER  

ibmfrDlcmiState 1.3.6.1.4.1.2.6.2.8.1.1.2
This variable states which Data Link Connec- tion Management scheme is active (and by impli- cation, what DLCI it uses) on the Frame Relay interface.
OBJECT-TYPE    
  INTEGER noLmiConfigured(1), lmiRev1(2), ansiT1-617-D(3), ansiT1-617-B(4)  

ibmfrDlcmiAddress 1.3.6.1.4.1.2.6.2.8.1.1.3
This variable states which address format is in use on the Frame Relay interface.
OBJECT-TYPE    
  INTEGER q921(1), q922March90(2), q922November90(3), q922(4)  

ibmfrDlcmiAddressLen 1.3.6.1.4.1.2.6.2.8.1.1.4
This variable states which address length in octets. In the case of Q922 format, the length indicates the entire length of the address in- cluding the control portion.
OBJECT-TYPE    
  INTEGER two-octets(2), three-octets(3), four-octets(4)  

ibmfrDlcmiPollingInterval 1.3.6.1.4.1.2.6.2.8.1.1.5
This is the number of seconds between succes- sive status enquiry messages.
OBJECT-TYPE    
  INTEGER 5..30  

ibmfrDlcmiFullEnquiryInterval 1.3.6.1.4.1.2.6.2.8.1.1.6
Number of status enquiry intervals that pass before issuance of a full status enquiry mes- sage.
OBJECT-TYPE    
  INTEGER 1..255  

ibmfrDlcmiErrorThreshold 1.3.6.1.4.1.2.6.2.8.1.1.7
This is the maximum number of unanswered Status Enquiries the equipment shall accept be- fore declaring the interface down.
OBJECT-TYPE    
  INTEGER 1..10  

ibmfrDlcmiMonitoredEvents 1.3.6.1.4.1.2.6.2.8.1.1.8
This is the maximum number of responses to FULL STATUS or LINK INTEGERITY VERIFICATION messages missed before the device will mark the interface down.
OBJECT-TYPE    
  INTEGER 1..10  

ibmfrDlcmiMaxSupportedVCs 1.3.6.1.4.1.2.6.2.8.1.1.9
The maximum number of Virtual Circuits allowed for this interface. Usually dictated by the Frame Relay network. In response to a SET, if a value less than zero or higher than the agent's maximal capability is configured, the agent should respond bad- Value
OBJECT-TYPE    
  INTEGER  

ibmfrDlcmiMulticast 1.3.6.1.4.1.2.6.2.8.1.1.10
This indicates whether the Frame Relay provid- er offers a Multicast Service.
OBJECT-TYPE    
  INTEGER nonBroadcast(1), broadcast(2)  

ibmfrCircuitTable 1.3.6.1.4.1.2.6.2.8.2
A table containing information about specific Data Link Connection Identifiers and corresponding virtual circuits.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmfrCircuitEntry

ibmfrCircuitEntry 1.3.6.1.4.1.2.6.2.8.2.1
The information regarding a single Data Link Connection Identifier.
OBJECT-TYPE    
  IbmfrCircuitEntry  

ibmfrCircuitIfIndex 1.3.6.1.4.1.2.6.2.8.2.1.1
The ifIndex Value of the ifEntry this virtual circuit is layered onto.
OBJECT-TYPE    
  INTEGER  

ibmfrCircuitDlci 1.3.6.1.4.1.2.6.2.8.2.1.2
The Data Link Connection Identifier for this virtual circuit.
OBJECT-TYPE    
  INTEGER  

ibmfrCircuitState 1.3.6.1.4.1.2.6.2.8.2.1.3
Indicates whether the particular virtual cir- cuit is operational. In the absence of a Data Link Connection Management Interface, virtual circuit entries (rows) may be created by set- ting virtual circuit state to active, or delet- ed by changing Circuit state to deleted. Whether or not the row actually disappears is let to the implementation, so this object may actually read as 'invalid' for some arbitrary length of time. It is also legal to set the state of a virtual circuit to inactive to tem- porarily disable a given circuit.
OBJECT-TYPE    
  INTEGER invalid(1), active(2), inactive(3)  

ibmfrCircuitReceivedFECNs 1.3.6.1.4.1.2.6.2.8.2.1.4
Number of frames received from the network in- dicating forward congestion since the virtual circuit was created.
OBJECT-TYPE    
  Counter  

ibmfrCircuitReceivedBECNs 1.3.6.1.4.1.2.6.2.8.2.1.5
Number of frames received from the network in- dicating backward congestion since the virtual circuit was created.
OBJECT-TYPE    
  Counter  

ibmfrCircuitSentFrames 1.3.6.1.4.1.2.6.2.8.2.1.6
The number of frames sent from this virtual circuit since it was created.
OBJECT-TYPE    
  Counter  

ibmfrCircuitSentOctets 1.3.6.1.4.1.2.6.2.8.2.1.7
The number of octets sent from this virtual circuit since it was created.
OBJECT-TYPE    
  Counter  

ibmfrCircuitReceivedFrames 1.3.6.1.4.1.2.6.2.8.2.1.8
Number of frames received over this virtual circuit since it was created.
OBJECT-TYPE    
  Counter  

ibmfrCircuitReceivedOctets 1.3.6.1.4.1.2.6.2.8.2.1.9
Number of octets received over this virtual circuit since it was created.
OBJECT-TYPE    
  Counter  

ibmfrCircuitCreationTime 1.3.6.1.4.1.2.6.2.8.2.1.10
The time when this virtual circuit was created, whether by the Data Link Connection Management Interface or by a SetRequest. The time value is relative to other times on this interface only.
OBJECT-TYPE    
  TimeTicks  

ibmfrCircuitLastTimeChange 1.3.6.1.4.1.2.6.2.8.2.1.11
The time when last there was a change in the virtual circuit state. The time value is relative to other times on this interface only.
OBJECT-TYPE    
  TimeTicks  

ibmfrCircuitCommittedBurst 1.3.6.1.4.1.2.6.2.8.2.1.12
This variable indicates the maximum amount of data, in bits, that the network agrees to transfer under normal conditions, during the measurement interval.
OBJECT-TYPE    
  INTEGER  

ibmfrCircuitExcessBurst 1.3.6.1.4.1.2.6.2.8.2.1.13
This variable indicates the maximum amount of uncommitted data bits that the network will at- tempt to deliver over the measurement interval. By default, if not configured when creating the entry, the Excess Information Burst Size is set to the value of ifSpeed.
OBJECT-TYPE    
  INTEGER  

ibmfrCircuitThroughput 1.3.6.1.4.1.2.6.2.8.2.1.14
Throughput is the average number of 'Frame Re- lay Information Field' bits transferred per second across a user network interface in one direction, measured over the measurement inter- val. If the configured committed burst rate and throughput are both non-zero, the measurement interval T=ibmfrCircuitCommittedBurst/ibmfrCircuitThroughput. If the configured committed burst rate and throughput are both zero, the measurement in- terval T=ibmfrCircuitExcessBurst/ifSpeed.
OBJECT-TYPE    
  INTEGER  

ibmfrErrTable 1.3.6.1.4.1.2.6.2.8.3
A table containing information about Errors on the Frame Relay interface.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmfrErrEntry

ibmfrErrEntry 1.3.6.1.4.1.2.6.2.8.3.1
The error information for a single frame relay interface.
OBJECT-TYPE    
  IbmfrErrEntry  

ibmfrErrIfIndex 1.3.6.1.4.1.2.6.2.8.3.1.1
The ifIndex Value of the corresponding ifEn- try.
OBJECT-TYPE    
  INTEGER  

ibmfrErrType 1.3.6.1.4.1.2.6.2.8.3.1.2
The type of error that was last seen on this interface.
OBJECT-TYPE    
  INTEGER unknownError(1), receiveShort(2), receiveLong(3), illegalDLCI(4), unknownDLCI(5), dlcmiProtoErr(6), dlcmiUnknownIE(7), dlcmiSequenceErr(8), dlcmiUnknownRpt(9)  

ibmfrErrData 1.3.6.1.4.1.2.6.2.8.3.1.3
An octet string containing as much of the er- ror packet as possible. As a minimum, it must contain the Q.922 Address or as much as was delivered. It is desirable to include all in- formation up to the PDU.
OBJECT-TYPE    
  OCTET STRING  

ibmfrErrTime 1.3.6.1.4.1.2.6.2.8.3.1.4
The time at which the error was detected. The time value is relative to other times on this interface only.
OBJECT-TYPE    
  TimeTicks  

ibmdls 1.3.6.1.4.1.2.6.2.9
OBJECT IDENTIFIER    

ibmdlsVirtualRingSegmentNumber 1.3.6.1.4.1.2.6.2.9.1
The token ring segment number used in all frames passed to or from the IBM 6611 Data Link Switching function.
OBJECT-TYPE    
  INTEGER 0..4095  

ibmdlsFrameFilterType 1.3.6.1.4.1.2.6.2.9.2
The type of SNA filtering applied using the ibmdlsLocalFrameFilterTable and ibmdlsRemoteFrameFilterTable. If this field = permit(2), then all filters defined for SNA use the action of permitting frames to be forwarded if they meet the criteria given by the source and destination address values. If this field = deny(1), then all filters defined for SNA use the action of denying frames to be forwarded if they meet the criteria given by the source and destination address values.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmdlsNameFilterType 1.3.6.1.4.1.2.6.2.9.3
The type of NetBIOS filtering applied using the ibmdlsLocalNameFilterTable and ibmdlsRemoteNameFilterTable. If this field = permit(2), then all filters defined for NetBIOS use the action of permitting frames to be forwarded if they meet the criteria given by the source and destination address values. If this field = deny(1), then all filters defined for NetBIOS use the action of denying frames to be forwarded if they meet the criteria given by the source and destination address values.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmdlsRouterTable 1.3.6.1.4.1.2.6.2.9.4
A table of information regarding all routers participating in Data Link Switching.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmdlsRouterEntry

ibmdlsRouterEntry 1.3.6.1.4.1.2.6.2.9.4.1
Information for a single participating router.
OBJECT-TYPE    
  IbmdlsRouterEntry  

ibmdlsRouterAddress 1.3.6.1.4.1.2.6.2.9.4.1.1
The IP address of the router participating in Data Link Switching.
OBJECT-TYPE    
  IpAddress  

ibmdlsRouterStatus 1.3.6.1.4.1.2.6.2.9.4.1.2
The current state of the remote connection
OBJECT-TYPE    
  INTEGER notActive(1), active(2)  

ibmdlsRouterDefinedBy 1.3.6.1.4.1.2.6.2.9.4.1.3
The origin of this entry. user(1) indicates that this router is defined via the Configuration Program. system(2) indicates that this router was defined automatically as a result of a connection request from another router.
OBJECT-TYPE    
  INTEGER user(1), system(2)  

ibmdlsRouterInFrames 1.3.6.1.4.1.2.6.2.9.4.1.4
Number of frames received from the partner router.
OBJECT-TYPE    
  Counter  

ibmdlsRouterOutFrames 1.3.6.1.4.1.2.6.2.9.4.1.5
Number of frames sent to the partner router.
OBJECT-TYPE    
  Counter  

ibmdlsLocalFrameFilterTable 1.3.6.1.4.1.2.6.2.9.5
The SNA local frame filter table. This table contains information regarding the filtering of SNA frames received from local LAN segments.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmdlsLocalFrameFilterEntry

ibmdlsLocalFrameFilterEntry 1.3.6.1.4.1.2.6.2.9.5.1
Filter information for a MAC address source-destination pair.
OBJECT-TYPE    
  IbmdlsLocalFrameFilterEntry  

ibmdlsLocalFrameFilterID 1.3.6.1.4.1.2.6.2.9.5.1.1
A unique identifier for this filter.
OBJECT-TYPE    
  INTEGER 1..100  

ibmdlsLocalFrameFilterSrcAddress 1.3.6.1.4.1.2.6.2.9.5.1.2
The source MAC address that this filter is applied to.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdlsLocalFrameFilterSrcMask 1.3.6.1.4.1.2.6.2.9.5.1.3
A mask indicating the bits of the source address considered significant when using the filter. For every bit equal to one in the mask, the same bit in the source address is considered significant.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdlsLocalFrameFilterDestAddress 1.3.6.1.4.1.2.6.2.9.5.1.4
The destination MAC address that this filter is applied to.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdlsLocalFrameFilterDestMask 1.3.6.1.4.1.2.6.2.9.5.1.5
A mask indicating the bits of the destination address considered significant when using the filter. For every bit equal to one in the mask, the same bit in the destination address is considered significant.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdlsRemoteFrameFilterTable 1.3.6.1.4.1.2.6.2.9.6
The SNA remote frame filter table. This table contains information regarding the filtering of SNA frames received from other participating DLS routers.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmdlsRemoteFrameFilterEntry

ibmdlsRemoteFrameFilterEntry 1.3.6.1.4.1.2.6.2.9.6.1
Filter information for a MAC address source-destination pair.
OBJECT-TYPE    
  IbmdlsRemoteFrameFilterEntry  

ibmdlsRemoteFrameFilterID 1.3.6.1.4.1.2.6.2.9.6.1.1
A unique identifier for this filter.
OBJECT-TYPE    
  INTEGER 1..100  

ibmdlsRemoteFrameFilterSrcAddress 1.3.6.1.4.1.2.6.2.9.6.1.2
The source MAC address that this filter is applied to.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdlsRemoteFrameFilterSrcMask 1.3.6.1.4.1.2.6.2.9.6.1.3
A mask indicating the bits of the source address considered significant when using the filter. For every bit equal to one in the mask, the same bit in the source address is considered significant.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdlsRemoteFrameFilterDestAddress 1.3.6.1.4.1.2.6.2.9.6.1.4
The destination MAC address that this filter is applied to.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdlsRemoteFrameFilterDestMask 1.3.6.1.4.1.2.6.2.9.6.1.5
A mask indicating the bits of the destination address considered significant when using the filter. For every bit equal to one in the mask, the same bit in the destination address is considered significant.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdlsLocalNameFilterTable 1.3.6.1.4.1.2.6.2.9.7
The NetBIOS local name filter table. This table contains information regarding the filtering of NetBIOS frames received from local LAN segments.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmdlsLocalNameFilterEntry

ibmdlsLocalNameFilterEntry 1.3.6.1.4.1.2.6.2.9.7.1
Filter information for a NetBIOS source-destination name pair.
OBJECT-TYPE    
  IbmdlsLocalNameFilterEntry  

ibmdlsLocalNameFilterID 1.3.6.1.4.1.2.6.2.9.7.1.1
A unique identifier for this filter.
OBJECT-TYPE    
  INTEGER 1..100  

ibmdlsLocalNameFilterSrcAddress 1.3.6.1.4.1.2.6.2.9.7.1.2
The source NetBIOS name that this filter is applied to.
OBJECT-TYPE    
  DisplayString SIZE(1..16)  

ibmdlsLocalNameFilterDestAddress 1.3.6.1.4.1.2.6.2.9.7.1.3
The destination NetBIOS name that this filter is applied to.
OBJECT-TYPE    
  DisplayString SIZE(1..16)  

ibmdlsRemoteNameFilterTable 1.3.6.1.4.1.2.6.2.9.8
The NetBIOS name filter table. This table contains information regarding the filtering of NetBIOS frames received from other participating DLS routers.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmdlsRemoteNameFilterEntry

ibmdlsRemoteNameFilterEntry 1.3.6.1.4.1.2.6.2.9.8.1
Filter information for a NetBIOS source-destination name pair.
OBJECT-TYPE    
  IbmdlsRemoteNameFilterEntry  

ibmdlsRemoteNameFilterID 1.3.6.1.4.1.2.6.2.9.8.1.1
A unique identifier for this filter.
OBJECT-TYPE    
  INTEGER 1..100  

ibmdlsRemoteNameFilterSrcAddress 1.3.6.1.4.1.2.6.2.9.8.1.2
The source NetBIOS name that this filter is applied to.
OBJECT-TYPE    
  DisplayString SIZE(1..16)  

ibmdlsRemoteNameFilterDestAddress 1.3.6.1.4.1.2.6.2.9.8.1.3
The destination NetBIOS name that this filter is applied to.
OBJECT-TYPE    
  DisplayString SIZE(1..16)  

ibmdlsDefaultDestTable 1.3.6.1.4.1.2.6.2.9.9
Table of default routers for MAC addresses.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmdlsDefaultDestEntry

ibmdlsDefaultDestEntry 1.3.6.1.4.1.2.6.2.9.9.1
Mapping of a MAC address to a default router.
OBJECT-TYPE    
  IbmdlsDefaultDestEntry  

ibmdlsDefaultDestAddress 1.3.6.1.4.1.2.6.2.9.9.1.1
The destination address that this table entry applies to.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdlsDefaultRouterAddress 1.3.6.1.4.1.2.6.2.9.9.1.2
The default router used for reaching the destination address in ibmdlsDefaultDestAddress.
OBJECT-TYPE    
  IpAddress  

ibmdlsDefaultNBDestTable 1.3.6.1.4.1.2.6.2.9.10
Table of default routers for NetBIOS names.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmdlsDefaultNBDestEntry

ibmdlsDefaultNBDestEntry 1.3.6.1.4.1.2.6.2.9.10.1
Mapping of a NetBIOS name to a default router.
OBJECT-TYPE    
  IbmdlsDefaultNBDestEntry  

ibmdlsDefaultNBDestName 1.3.6.1.4.1.2.6.2.9.10.1.1
The destination NetBIOS name that this table entry applies to.
OBJECT-TYPE    
  DisplayString SIZE(1..16)  

ibmdlsDefaultNBRouterAddress 1.3.6.1.4.1.2.6.2.9.10.1.2
The default router used for reaching the destination name in ibmdlsDefaultNBDestName.
OBJECT-TYPE    
  IpAddress  

ibmdlsStationTable 1.3.6.1.4.1.2.6.2.9.11
Table of configuration information on SNA stations attached to this router.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmdlsStationEntry

ibmdlsStationEntry 1.3.6.1.4.1.2.6.2.9.11.1
Information on a single SNA station attached to this router.
OBJECT-TYPE    
  IbmdlsStationEntry  

ibmdlsStationIfIndex 1.3.6.1.4.1.2.6.2.9.11.1.1
The value of IfIndex for the port to which this station is attached.
OBJECT-TYPE    
  INTEGER  

ibmdlsStationAddress 1.3.6.1.4.1.2.6.2.9.11.1.2
The SDLC address of this station.
OBJECT-TYPE    
  INTEGER 1..255  

ibmdlsStationTransmitWindowCount 1.3.6.1.4.1.2.6.2.9.11.1.3
The number of SDLC information frames to send to this station before turning the line around to get a response.
OBJECT-TYPE    
  INTEGER 1..7  

ibmdlsStationRetransmitCount 1.3.6.1.4.1.2.6.2.9.11.1.4
The number of contiguous information frame bursts that will be transmitted to this station before declaring a permanent transmission error.
OBJECT-TYPE    
  INTEGER 1..50  

ibmdlsStationRetransmitThreshold 1.3.6.1.4.1.2.6.2.9.11.1.5
The number of information frame transmissions allowed as a percentage of total information frame transmissions. The specified rate is the maximum rate of retransmissions allowed above which an error log entry will be make.
OBJECT-TYPE    
  INTEGER 1..100  

ibmdlsStationForceDisconnectTimeout 1.3.6.1.4.1.2.6.2.9.11.1.6
The number of seconds that the IBM 6611 will wait after requesting a disconnect from the link (DISC) before forcing a disconnect.
OBJECT-TYPE    
  INTEGER 1..600  

ibmdlsStationMaxIfieldSize 1.3.6.1.4.1.2.6.2.9.11.1.7
The value in bytes of the maximum I-field size (a multiple of 256 plus 9).
OBJECT-TYPE    
  INTEGER 265..30729  

ibmdlsStationPrimaryRepollTimeout 1.3.6.1.4.1.2.6.2.9.11.1.8
The length of time (in tenths of seconds) that the primary station will wait for a response from the secondary station.
OBJECT-TYPE    
  INTEGER 1..250  

ibmdlsStationPrimaryRepollCount 1.3.6.1.4.1.2.6.2.9.11.1.9
The number of times that the primary station will poll the secondary station unsuccessfully before marking the station as not working.
OBJECT-TYPE    
  INTEGER 3..50  

ibmdlsStationPrimaryRepollThreshold 1.3.6.1.4.1.2.6.2.9.11.1.10
The number of repolls as a percentage of the total polls sent to the secondary station. The specified percentage equals the maximum rate of repolls allowed, above which the IBM 6611 declares that a temporary error has occurred and logs an entry in the system error log.
OBJECT-TYPE    
  INTEGER 1..100  

ibmdlsStationPrimarySlowListTimeout 1.3.6.1.4.1.2.6.2.9.11.1.11
The number of seconds that the primary station will wait between polls to stations on the slow list.
OBJECT-TYPE    
  INTEGER 1..60  

ibmdlsStationSrcAddress 1.3.6.1.4.1.2.6.2.9.11.1.12
The token ring physical address used for this station.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdlsStationDestAddress 1.3.6.1.4.1.2.6.2.9.11.1.13
The token ring physical address to which this station should be connected. If this information is not available the IBM 6611 Network Processor will return a length of zero for this object.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdlsCirTable 1.3.6.1.4.1.2.6.2.9.12
Table of information on DLS circuits active on this router.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmdlsCirEntry

ibmdlsCirEntry 1.3.6.1.4.1.2.6.2.9.12.1
Information on a DLS circuit.
OBJECT-TYPE    
  IbmdlsCirEntry  

ibmdlsCirIfIndex 1.3.6.1.4.1.2.6.2.9.12.1.1
The value of IfIndex for the interface supporting this circuit.
OBJECT-TYPE    
  INTEGER  

ibmdlsCirSrcAddress 1.3.6.1.4.1.2.6.2.9.12.1.2
The MAC address of the source of this circuit.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdlsCirSrcSap 1.3.6.1.4.1.2.6.2.9.12.1.3
The SAP identifier of the source of this circuit.
OBJECT-TYPE    
  INTEGER  

ibmdlsCirDestAddress 1.3.6.1.4.1.2.6.2.9.12.1.4
The MAC address of the destination of this circuit.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdlsCirDestSap 1.3.6.1.4.1.2.6.2.9.12.1.5
The SAP identifier of the destination of this circuit.
OBJECT-TYPE    
  INTEGER  

ibmdlsCirPartnerRouterAddress 1.3.6.1.4.1.2.6.2.9.12.1.6
The IP address of the partner router used by this circuit.
OBJECT-TYPE    
  IpAddress  

ibmdlsCirLocalLinkState 1.3.6.1.4.1.2.6.2.9.12.1.7
The state of the local link station used by this circuit.
OBJECT-TYPE    
  INTEGER opening(1), opened(2), closing(3), inactive(4)  

ibmdlsCirLocalLinkSubState 1.3.6.1.4.1.2.6.2.9.12.1.8
The sub-state of the local link station used by this circuit.
OBJECT-TYPE    
  INTEGER calling(1), listening(2), contacted(3), localBusy(4), remoteBusy(5)  

ibmdlsCirLocalLinkRouting 1.3.6.1.4.1.2.6.2.9.12.1.9
The routing information field used by the local link portion of this circuit. The routing information field consists of a 2-byte routing control field and up to eight 2-byte route designators.
OBJECT-TYPE    
  OCTET STRING SIZE(4..18)  

ibmdlsCirLocalLinkTestCmdsSent 1.3.6.1.4.1.2.6.2.9.12.1.10
The number of test commands sent by the local link station used by this circuit.
OBJECT-TYPE    
  Counter  

ibmdlsCirLocalLinkTestCmdsFail 1.3.6.1.4.1.2.6.2.9.12.1.11
The number of test commands failed by the local link station used by this circuit.
OBJECT-TYPE    
  Counter  

ibmdlsCirLocalLinkTestCmdsRcv 1.3.6.1.4.1.2.6.2.9.12.1.12
The number of test commands received by the local link station used by this circuit.
OBJECT-TYPE    
  Counter  

ibmdlsCirLocalLinkDataPktSent 1.3.6.1.4.1.2.6.2.9.12.1.13
The number of sequenced data packets sent by the local link station used by this circuit.
OBJECT-TYPE    
  Counter  

ibmdlsCirLocalLinkDataPktResent 1.3.6.1.4.1.2.6.2.9.12.1.14
The number of sequenced data packets resent by the local link station used by this circuit.
OBJECT-TYPE    
  Counter  

ibmdlsCirLocalLinkMaxContResent 1.3.6.1.4.1.2.6.2.9.12.1.15
The maximum number of contiguous resendings by the local link station used by this circuit.
OBJECT-TYPE    
  Counter  

ibmdlsCirLocalLinkDataPktRcv 1.3.6.1.4.1.2.6.2.9.12.1.16
The number of sequenced data packets received by the local link station used by this circuit.
OBJECT-TYPE    
  Counter  

ibmdlsCirLocalLinkInvalidPktRcv 1.3.6.1.4.1.2.6.2.9.12.1.17
The number of invalid packets received by the local link station used by this circuit.
OBJECT-TYPE    
  Counter  

ibmdlsCirLocalLinkAdpRcvErr 1.3.6.1.4.1.2.6.2.9.12.1.18
The number of data-detected receive errors by the local link station used by this circuit.
OBJECT-TYPE    
  Counter  

ibmdlsCirLocalLinkAdpSendErr 1.3.6.1.4.1.2.6.2.9.12.1.19
The number of data-detected transmit errors by the local link station used by this circuit.
OBJECT-TYPE    
  Counter  

ibmdlsCirLocalLinkRcvInactiveTimeouts 1.3.6.1.4.1.2.6.2.9.12.1.20
The number of inactivity timeouts received by the local link station used by this circuit.
OBJECT-TYPE    
  Counter  

ibmdlsCirLocalLinkCmdPollsSent 1.3.6.1.4.1.2.6.2.9.12.1.21
The number of command polls sent by the local link station used by this circuit.
OBJECT-TYPE    
  Counter  

ibmdlsCirLocalLinkCmdRepollsSent 1.3.6.1.4.1.2.6.2.9.12.1.22
The number of command repolls sent by the local link station used by this circuit.
OBJECT-TYPE    
  Counter  

ibmdlsCirLocalLinkCmdContRepolls 1.3.6.1.4.1.2.6.2.9.12.1.23
The number of continuous repolls sent by the local link station used by this circuit.
OBJECT-TYPE    
  Counter  

ibmdlsCirLocalAddress 1.3.6.1.4.1.2.6.2.9.12.1.24
The address (ibmdlsCirSrcAddress or ibmdlsCirDestAddress) that is local on this circuit.
OBJECT-TYPE    
  INTEGER sourceIsLocal(1), destinationIsLocal(2)  

ibmppp 1.3.6.1.4.1.2.6.2.10
OBJECT IDENTIFIER    

ibmpppLinkControlTable 1.3.6.1.4.1.2.6.2.10.1
A table containing PPP-link specific control variables for this managed object. An entry in this table is uniquely identified by the ibmpppLinkControlIndex value comprised by said entry.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmpppLinkControlEntry

ibmpppLinkControlEntry 1.3.6.1.4.1.2.6.2.10.1.1
Management control information about a particular PPP Link.
OBJECT-TYPE    
  IbmpppLinkControlEntry  

ibmpppLinkControlIndex 1.3.6.1.4.1.2.6.2.10.1.1.1
A unique value for each PPP link. Its value ranges between 1 and the value of ifNumber. The interface identified by a particular value of this index is that identified by the same value of an ifIndex object instance. The value for each link must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

ibmpppLinkCRCSize 1.3.6.1.4.1.2.6.2.10.1.1.2
Number of bits used in the CRC on this link. See section 3.1, 'Frame Check Sequence (FCS) Field' on page 5 of RFC 1171. Setting this object to a new value will have effect when this link is next restarted.
OBJECT-TYPE    
  INTEGER ppp-crc-16(16), ppp-crc-32(32)  

ibmpppLinkRestartTimerValue 1.3.6.1.4.1.2.6.2.10.1.1.3
The value used for the Restart Timer. It is in units of hundredths of a second. See section 4.3, 'Timers and Counters' on page 20 of RFC 1171.
OBJECT-TYPE    
  INTEGER  

ibmpppLinkMaxRestarts 1.3.6.1.4.1.2.6.2.10.1.1.4
The Max-Restarts parameter described in section 4.3, 'Timers and Counters' on page 20 of RFC 1171.
OBJECT-TYPE    
  INTEGER  

ibmpppLinkLocalMRU 1.3.6.1.4.1.2.6.2.10.1.1.5
The MRU (Maximum Receive Unit) of this node on the link. See section 2.1, page 2, 'Maximum Receive Unit' of RFC 1172. Changing this object will have effect when the link is next restarted.
OBJECT-TYPE    
  INTEGER  

ibmpppLinkRemoteMRU 1.3.6.1.4.1.2.6.2.10.1.1.6
What this node believes is the MRU for the node on the other end of the link. See section 2.1, page 2, 'Maximum Receive Unit' of RFC 1172. Changing this object will immediately cause the local node to use the new MRU when transmitting packets. If this number is increased, then the sender MAY elect to use the new MRU. If the MRU is decreased then the sender MUST use the new MRU.
OBJECT-TYPE    
  INTEGER  

ibmpppLinkLocalACCMap 1.3.6.1.4.1.2.6.2.10.1.1.7
The (ACC) Asynchronous-Control-Character-Map for this node. This is the ACC Map that the node on the other end of the link will use when building a packet to send to this node. See section 2.2, page 3, 'Async-Control- Character-Map' of RFC 1172. The IBM 6611 Network Processor always provides a value of zero for this object.
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

ibmpppLinkRemoteACCMap 1.3.6.1.4.1.2.6.2.10.1.1.8
The (ACC) Asynchronous-Control-Character-Map that this node uses when building a packet to send to the node on the other end of the link. See section 2.2, page 3, 'Async-Control-Character-Map' of RFC 1172. The IBM 6611 Network Processor always provides a value of zero for this object.
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

ibmpppLinkMagicLoopCount 1.3.6.1.4.1.2.6.2.10.1.1.9
The number of times that this node will do a Magic Number Configuration before deciding that the link is looped back. 0 indicates that the node does not do Magic Number Configuration. -1 indicates that it tries forever. Changing this object takes effect the next time that the link is restarted.
OBJECT-TYPE    
  INTEGER  

ibmpppLinkCommand 1.3.6.1.4.1.2.6.2.10.1.1.10
See section 4.14 on page 13 of RFC 1171. Reading from this variable will return no-op(1). The IBM 6611 Network Processor always provides a value of no-op(1) for this object.
OBJECT-TYPE    
  INTEGER no-op(1), close(2)  

ibmpppLinkStatusTable 1.3.6.1.4.1.2.6.2.10.2
A table containing PPP-link status specific information for this managed object. An entry in this table is uniquely identified by the ibmpppLinkStatusIndex value comprised by said entry.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmpppLinkStatusEntry

ibmpppLinkStatusEntry 1.3.6.1.4.1.2.6.2.10.2.1
Status information about a particular PPP Link.
OBJECT-TYPE    
  IbmpppLinkStatusEntry  

ibmpppLinkStatusIndex 1.3.6.1.4.1.2.6.2.10.2.1.1
A unique value for each PPP link. Its value ranges between 1 and the value of ifNumber. The interface identified by a particular value of this index is that identified by the same value of an ifIndex object instance. The value for each link must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

ibmpppLinkVersion 1.3.6.1.4.1.2.6.2.10.2.1.2
The version of LCP that is being run over this link (per RFC 1171). This value currently must be 1.
OBJECT-TYPE    
  INTEGER  

ibmpppLinkCurrentState 1.3.6.1.4.1.2.6.2.10.2.1.3
The current state of the link automaton. See section 4.1.3. 'State Transition Table' on page 13 of RFC 1171.
OBJECT-TYPE    
  INTEGER closed(1), listen(2), reqsent(3), ackrecvd(4), acksent(5), open(6), closing(7)  

ibmpppLinkPreviousState 1.3.6.1.4.1.2.6.2.10.2.1.4
The immediately previous state of the link automaton. See section 4.1.3. 'State Transition Table' on page 13 of RFC 1171.
OBJECT-TYPE    
  INTEGER closed(1), listen(2), reqsent(3), ackrecvd(4), acksent(5), open(6), closing(7)  

ibmpppLinkChangeTime 1.3.6.1.4.1.2.6.2.10.2.1.5
The value of sysUpTime when the state of the link automaton last changed.
OBJECT-TYPE    
  TimeTicks  

ibmpppLinkMagicNumber 1.3.6.1.4.1.2.6.2.10.2.1.6
This node's Magic Number. See section 2.4, page 7, 'Magic Number' of RFC 1172.
OBJECT-TYPE    
  INTEGER  

ibmpppLinkLocalQualityPeriod 1.3.6.1.4.1.2.6.2.10.2.1.7
This is the maximum interval at which this node will transmit Link-Quality-Report Packets. See section 2.5, on page 10 of RFC 1172. This object is in units of microseconds.
OBJECT-TYPE    
  INTEGER  

ibmpppLinkRemoteQualityPeriod 1.3.6.1.4.1.2.6.2.10.2.1.8
This is the maximum interval at which this node expects that the other node will transmit Link-Quality-Report Packets. See section 2.5, on page 10 of RFC 1172. This object is in units of microseconds.
OBJECT-TYPE    
  INTEGER  

ibmpppLinkProtocolCompression 1.3.6.1.4.1.2.6.2.10.2.1.9
Indicates the Protocol compression that has been configured on the link. Receive-only(1) indicates that this node can receive compressed packets but won't send them. Send-only(2) indicates that this node will send compressed packets but can not receive them. Receive-and-send(3) indicates that the node will send and can receive compressed packets. None(4) indicates that this node will neither send nor receive compressed packets. See section 2.6, on page 11 of RFC 1172. The IBM 6611 Network Processor always provides a value of none(4) for this object.
OBJECT-TYPE    
  INTEGER receive-only(1), send-only(2), receive-and-send(3), none(4)  

ibmpppLinkACCompression 1.3.6.1.4.1.2.6.2.10.2.1.10
Indicates the Address/Control Field compression that has been configured on the link. Receive-only(1) indicates that this node can receive compressed packets but won't send them. Send-only(2) indicates that this node will send compressed packets but can not receive them. Receive-and- send(3) indicates that the node will send and can receive compressed packets. None(4) indicates that this node will neither send nor receive compressed packets. See section 2.7, on page 13 of RFC 1172. The IBM 6611 Network Processor always provides a value of none(4) for this object.
OBJECT-TYPE    
  INTEGER receive-only(1), send-only(2), receive-and-send(3), none(4)  

ibmpppLinkMeasurementsValid 1.3.6.1.4.1.2.6.2.10.2.1.11
The current value of the Measurements-Valid state variable used for Link-Quality Management. See section 3.5, page 19, of RFC 1172.
OBJECT-TYPE    
  INTEGER  

ibmpppLinkQuality 1.3.6.1.4.1.2.6.2.10.2.1.12
The current quality of the link as declared by the nodes Link-Quality Management modules. No effort is made to define good or bad, nor the policy used to determine it.
OBJECT-TYPE    
  INTEGER good(1), bad(2)  

ibmpppLinkPhysical 1.3.6.1.4.1.2.6.2.10.2.1.13
A reference to MIB definitions specific to the particular physical interface type (e.g. T1) being used by the PPP Link. If the agent is unable to obtain this information, the value of this object will be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

ibmpppLinkErrorsTable 1.3.6.1.4.1.2.6.2.10.3
A table containing PPP-link specific statistical information for this managed object. An entry in this table is uniquely identified by the ibmpppLinkErrorsIndex value comprised by said entry.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmpppLinkErrorsEntry

ibmpppLinkErrorsEntry 1.3.6.1.4.1.2.6.2.10.3.1
Error information about a particular PPP Link.
OBJECT-TYPE    
  IbmpppLinkErrorsEntry  

ibmpppLinkErrorsIndex 1.3.6.1.4.1.2.6.2.10.3.1.1
A unique value for each PPP link. Its value ranges between 1 and the value of ifNumber. The interface identified by a particular value of this index is that identified by the same value of an ifIndex object instance. The value for each link must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

ibmpppLinkBadAddresses 1.3.6.1.4.1.2.6.2.10.3.1.2
The number of packets received with an incorrect Address Field. See section 3.1, Page 5, 'Address Field' of RFC 1171.
OBJECT-TYPE    
  Counter  

ibmpppLinkLastBadAddress 1.3.6.1.4.1.2.6.2.10.3.1.3
The most recent incorrect address received on this link.
OBJECT-TYPE    
  OCTET STRING  

ibmpppLinkBadControls 1.3.6.1.4.1.2.6.2.10.3.1.4
The number of packets received on this link with an incorrect Control Field. See Section 3.1, Page 5, 'Flag Sequence' of RFC 1171.
OBJECT-TYPE    
  Counter  

ibmpppLinkLastBadControl 1.3.6.1.4.1.2.6.2.10.3.1.5
The most recent incorrect Control Field received on this link.
OBJECT-TYPE    
  OCTET STRING  

ibmpppLinkLastUnknownProtocol 1.3.6.1.4.1.2.6.2.10.3.1.6
The most recently received unknown Protocol. An unknown Protocol is one which has a well-formed Protocol number, but which the PPP implementation does not know how to handle.
OBJECT-TYPE    
  OCTET STRING  

ibmpppLinkInvalidProtocols 1.3.6.1.4.1.2.6.2.10.3.1.7
The number of times that a packet has been received with an invalid Protocol specified in the Protocol Field. An invalid Protocol is one which does not conform to the requirements of section 3.1, page 5 of RFC 1171.
OBJECT-TYPE    
  Counter  

ibmpppLinkLastInvalidProtocol 1.3.6.1.4.1.2.6.2.10.3.1.8
The most recently received invalid Protocol.
OBJECT-TYPE    
  OCTET STRING  

ibmpppLinkPacketTooLongs 1.3.6.1.4.1.2.6.2.10.3.1.9
The number of received packets that have been discarded because their length exceeded the MRU.
OBJECT-TYPE    
  Counter  

ibmpppLinkBadCRCs 1.3.6.1.4.1.2.6.2.10.3.1.10
The number of received packets that have been discarded due to having an incorrect CRC.
OBJECT-TYPE    
  Counter  

ibmpppLinkConfigTimeouts 1.3.6.1.4.1.2.6.2.10.3.1.11
The number of Configure Request packets that have timed out.
OBJECT-TYPE    
  Counter  

ibmpppLinkTerminateTimeouts 1.3.6.1.4.1.2.6.2.10.3.1.12
The number of Terminate Request packets that have timed out.
OBJECT-TYPE    
  Counter  

ibmpppLinkQualityTable 1.3.6.1.4.1.2.6.2.10.4
A table containing PPP-link specific statistical information for this managed object. An entry in this table is uniquely identified by the ibmpppLinkQualityIndex value comprised by said entry.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmpppLinkQualityEntry

ibmpppLinkQualityEntry 1.3.6.1.4.1.2.6.2.10.4.1
Link Quality Management information about a particular PPP Link.
OBJECT-TYPE    
  IbmpppLinkQualityEntry  

ibmpppLinkQualityIndex 1.3.6.1.4.1.2.6.2.10.4.1.1
A unique value for each PPP link. Its value ranges between 1 and the value of ifNumber. The interface identified by a particular value of this index is that identified by the same value of an ifIndex object instance. The value for each link must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

ibmpppLinkInTxLQRs 1.3.6.1.4.1.2.6.2.10.4.1.2
The current value of In-Tx-LQRs used in Link-Quality Management. See section 3.5, page 19, of RFC 1172.
OBJECT-TYPE    
  Counter  

ibmpppLinkInTxPackets 1.3.6.1.4.1.2.6.2.10.4.1.3
The current value of the In-Tx-Packets counter used for Link-Quality Management. See section 3.5, page 19, of RFC 1172.
OBJECT-TYPE    
  Counter  

ibmpppLinkLastOutTxPackets 1.3.6.1.4.1.2.6.2.10.4.1.4
The current value of the Last-Out-Tx-Packets-Ctr counter used bu Link-Quality Management. See section 3.5, page 19, of RFC 1172.
OBJECT-TYPE    
  Counter  

ibmpppLinkInTxOctets 1.3.6.1.4.1.2.6.2.10.4.1.5
The current value of the In-Tx-Octets counter used for Link-Quality Management. See section 3.5, page 19, of RFC 1172.
OBJECT-TYPE    
  Counter  

ibmpppLinkLastOutTxOctets 1.3.6.1.4.1.2.6.2.10.4.1.6
The current value of the Last-Out-Tx-Octets-Counter counter used for Link-Quality Management. See section 3.5, page 19, of RFC 1172.
OBJECT-TYPE    
  Counter  

ibmpppLinkInRxPackets 1.3.6.1.4.1.2.6.2.10.4.1.7
The current value of the In-Rx-Packets counter used for Link-Quality Management. See section 3.5, page 19, of RFC 1172.
OBJECT-TYPE    
  Counter  

ibmpppLinkLastInRxPackets 1.3.6.1.4.1.2.6.2.10.4.1.8
The current value of the Last-In-Rx-Packets-Ctr counter used for Link-Quality Management. See section 3.5, page 19, of RFC 1172.
OBJECT-TYPE    
  Counter  

ibmpppLinkInRxOctets 1.3.6.1.4.1.2.6.2.10.4.1.9
The current value of the In-Rx-Octets counter used for Link-Quality Management. See section 3.5, page 19, of RFC 1172.
OBJECT-TYPE    
  Counter  

ibmpppLinkLastInRxOctets 1.3.6.1.4.1.2.6.2.10.4.1.10
The current value of the Last-In-Rx-Octets-Ctr counter used for Link-Quality Management. See section 3.5, page 19, of RFC 1172.
OBJECT-TYPE    
  Counter  

ibmpppProtocolTables 1.3.6.1.4.1.2.6.2.10.5
OBJECT IDENTIFIER    

ibmpppIPTable 1.3.6.1.4.1.2.6.2.10.5.1
A table containing specific information for the running of the IP over PPP in this managed object. An entry in this table is uniquely identified by the ibmpppIPLinkNumber value comprised by said entry.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmpppIPEntry

ibmpppIPEntry 1.3.6.1.4.1.2.6.2.10.5.1.1
All information pertinant to running the IP over a single PPP link.
OBJECT-TYPE    
  IbmpppIPEntry  

ibmpppIPLinkNumber 1.3.6.1.4.1.2.6.2.10.5.1.1.1
The value of ibmpppLinkIndex for the link over which this instance of the IP is being run.
OBJECT-TYPE    
  INTEGER  

ibmpppIPRejects 1.3.6.1.4.1.2.6.2.10.5.1.1.2
The number of Protocol Reject Messages received when attempting to send an IP packet over the link identified by ibmpppIPLinkNumber.
OBJECT-TYPE    
  Counter  

ibmpppIPInPackets 1.3.6.1.4.1.2.6.2.10.5.1.1.3
The number of IP packets received on the link identified by ibmpppIPLinkNumber.
OBJECT-TYPE    
  Counter  

ibmpppIPInOctets 1.3.6.1.4.1.2.6.2.10.5.1.1.4
The number of octets received in IP packets received on the link identified by ibmpppIPLinkNumber. Only octets in the PPP Information Field are counted. Octets inserted for transparency are not counted. Padding octets are not counted.
OBJECT-TYPE    
  Counter  

ibmpppIPOutPackets 1.3.6.1.4.1.2.6.2.10.5.1.1.5
The number of IP packets sent on the link identified by ibmpppIPLinkNumber.
OBJECT-TYPE    
  Counter  

ibmpppIPOutOctets 1.3.6.1.4.1.2.6.2.10.5.1.1.6
The number of octets all in IP Packets sent on the link identified by ibmpppIPLinkNumber. Only octets in the PPP Information Field are counted. Octets inserted for transparency are not counted. Padding octets are not counted.
OBJECT-TYPE    
  Counter  

ibmpppIPCPTable 1.3.6.1.4.1.2.6.2.10.5.2
A table containing specific information for the running of the IPCP over PPP in this managed object. An entry in this table is uniquely identified by the ibmpppIPCPLinkNumber value comprised by said entry.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmpppIPCPEntry

ibmpppIPCPEntry 1.3.6.1.4.1.2.6.2.10.5.2.1
All information pertinant to running the IPCP over a single PPP link.
OBJECT-TYPE    
  IbmpppIPCPEntry  

ibmpppIPCPLinkNumber 1.3.6.1.4.1.2.6.2.10.5.2.1.1
The value of ibmpppLinkIndex for the link over which this instance of the IPCP is being run.
OBJECT-TYPE    
  INTEGER  

ibmpppIPCPRejects 1.3.6.1.4.1.2.6.2.10.5.2.1.2
The number of Protocol Reject Messages received when attempting to send an IPCP Packet over the link identified by ibmpppIPCPLinkNumber.
OBJECT-TYPE    
  Counter  

ibmpppIPCPInPackets 1.3.6.1.4.1.2.6.2.10.5.2.1.3
The number of IPCP packets received on the link identified by ibmpppIPCPLinkNumber.
OBJECT-TYPE    
  Counter  

ibmpppIPCPInOctets 1.3.6.1.4.1.2.6.2.10.5.2.1.4
The number of octets received in IPCP packets received on the link identified by ibmpppIPCPLinkNumber. Only octets in the PPP Information Field are counted. Octets inserted for transparency are not counted. Padding octets are not counted.
OBJECT-TYPE    
  Counter  

ibmpppIPCPOutPackets 1.3.6.1.4.1.2.6.2.10.5.2.1.5
The number of IPCP packets sent on the link identified by ibmpppIPLinkNumber.
OBJECT-TYPE    
  Counter  

ibmpppIPCPOutOctets 1.3.6.1.4.1.2.6.2.10.5.2.1.6
The number of octets all in IPCP packets sent on the link identified by ibmpppIPCPLinkNumber. Only octets in the PPP Information Field are counted. Octets inserted for transparency are not counted. Padding octets are not counted.
OBJECT-TYPE    
  Counter  

ibmpppIPCPCompressionType 1.3.6.1.4.1.2.6.2.10.5.2.1.7
The compression type used on this link as defined in section 5.2 of RFC 1172. The numerical values that this object can be are the same as the numerical values that are included in the IPCP compression option configuration packets. The IBM 6611 Network Processor always provides a value of none(1) for this object.
OBJECT-TYPE    
  INTEGER none(1), van-jacobson-compressed-tcp(2)  

ibmpppLCPTable 1.3.6.1.4.1.2.6.2.10.5.3
A table containing specific information for the running of LCP over PPP in this managed object. An entry in this table is uniquely identified by the ibmpppLCPLinkNumber value comprised by said entry.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmpppLCPEntry

ibmpppLCPEntry 1.3.6.1.4.1.2.6.2.10.5.3.1
All information pertinant to running LCP over a single PPP link.
OBJECT-TYPE    
  IbmpppLCPEntry  

ibmpppLCPLinkNumber 1.3.6.1.4.1.2.6.2.10.5.3.1.1
The value of ibmpppLinkIndex for the link over which this instance of LCP is being run.
OBJECT-TYPE    
  INTEGER  

ibmpppLCPRejects 1.3.6.1.4.1.2.6.2.10.5.3.1.2
The number of Protocol Reject Messages received when attempting to send an LCP packet over the link identified by ibmpppLCPLinkNumber. This really ought not to happen.
OBJECT-TYPE    
  Counter  

ibmpppLCPInPackets 1.3.6.1.4.1.2.6.2.10.5.3.1.3
The number of LCP packets received on the link identified by ibmpppLCPLinkNumber.
OBJECT-TYPE    
  Counter  

ibmpppLCPInOctets 1.3.6.1.4.1.2.6.2.10.5.3.1.4
The number of octets received in LCP packets received on the link identified by ibmpppLCPLinkNumber. Only octets in the PPP Information Field are counted. Octets inserted for transparency are not counted. Padding octets are not counted.
OBJECT-TYPE    
  Counter  

ibmpppLCPOutPackets 1.3.6.1.4.1.2.6.2.10.5.3.1.5
The number of LCP packets sent on the link identified by ibmpppLCPLinkNumber.
OBJECT-TYPE    
  Counter  

ibmpppLCPOutOctets 1.3.6.1.4.1.2.6.2.10.5.3.1.6
The number of octets all in LCP packets sent on the link identified by ibmpppLCPLinkNumber. Only octets in the PPP Information Field are counted. Octets inserted for transparency are not counted. Padding octets are not counted.
OBJECT-TYPE    
  Counter  

ibmpppLCPOutCRs 1.3.6.1.4.1.2.6.2.10.5.3.1.7
Number of Configuration Request packets sent on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPInCRs 1.3.6.1.4.1.2.6.2.10.5.3.1.8
Number of Configuration Request packets received on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPOutCAs 1.3.6.1.4.1.2.6.2.10.5.3.1.9
Number of Configuration Acknowledge packets sent on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPInCAs 1.3.6.1.4.1.2.6.2.10.5.3.1.10
Number of Configuration Acknowledge packets received on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPOutCNs 1.3.6.1.4.1.2.6.2.10.5.3.1.11
Number of Configuration NAK packets sent on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPInCNs 1.3.6.1.4.1.2.6.2.10.5.3.1.12
Number of Configuration NAK packets received on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPOutCRejs 1.3.6.1.4.1.2.6.2.10.5.3.1.13
Number of Configuration Reject packets sent on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPInCRejs 1.3.6.1.4.1.2.6.2.10.5.3.1.14
Number of Configuration Reject packets received on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPOutTRs 1.3.6.1.4.1.2.6.2.10.5.3.1.15
Number of Terminate Request packets sent on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPInTRs 1.3.6.1.4.1.2.6.2.10.5.3.1.16
Number of Terminate Request packets received on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPOutTAs 1.3.6.1.4.1.2.6.2.10.5.3.1.17
Number of Terminate Acknowledge packets sent on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPInTAs 1.3.6.1.4.1.2.6.2.10.5.3.1.18
Number of Terminate Acknowledge packets received on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPOutCodeRejs 1.3.6.1.4.1.2.6.2.10.5.3.1.19
Number of Code Reject packets sent on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPInCodeRejs 1.3.6.1.4.1.2.6.2.10.5.3.1.20
Number of Code Reject packets received on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPOutEchoReqs 1.3.6.1.4.1.2.6.2.10.5.3.1.21
Number of Echo Request packets sent on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPInEchoReqs 1.3.6.1.4.1.2.6.2.10.5.3.1.22
Number of Echo Request packets received on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPOutEchoReps 1.3.6.1.4.1.2.6.2.10.5.3.1.23
Number of Echo Reply packets sent on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPInEchoReps 1.3.6.1.4.1.2.6.2.10.5.3.1.24
Number of Echo Reply packets received on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPOutDiscReqs 1.3.6.1.4.1.2.6.2.10.5.3.1.25
Number of Discard Request packets sent on this link.
OBJECT-TYPE    
  Counter  

ibmpppLCPInDiscReqs 1.3.6.1.4.1.2.6.2.10.5.3.1.26
Number of Discard Request packets received on this link.
OBJECT-TYPE    
  Counter  

ibmxns 1.3.6.1.4.1.2.6.2.11
OBJECT IDENTIFIER    

ibmxnsidpForwarding 1.3.6.1.4.1.2.6.2.11.1
Indicates if this node is acting as an XNS router.
OBJECT-TYPE    
  INTEGER forwarding(1), not-forwarding(2)  

ibmxnsConfigTable 1.3.6.1.4.1.2.6.2.11.4
The table of XNS configuration information gathered on a per-interface basis.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmXnsConfigEntry

ibmxnsConfigEntry 1.3.6.1.4.1.2.6.2.11.4.1
XNS configuration information for a single interface.
OBJECT-TYPE    
  IbmXnsConfigEntry  

ibmxnsPortIfIndex 1.3.6.1.4.1.2.6.2.11.4.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmxnsPortStatus 1.3.6.1.4.1.2.6.2.11.4.1.2
The status of the XNS protocol stack on this interface.
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

ibmxnsidpChecksum 1.3.6.1.4.1.2.6.2.11.4.1.3
Indicates the type of checksumming being done by IDP.
OBJECT-TYPE    
  INTEGER off(1), header(2), packet(3)  

ibmxnsErrpActive 1.3.6.1.4.1.2.6.2.11.4.1.4
Indicates if this port is originating error protocol packets.
OBJECT-TYPE    
  INTEGER active(1), suppressed(2)  

ibmxnsLoopbackActive 1.3.6.1.4.1.2.6.2.11.4.1.5
Indicates if this port will use the hardware to loopback locally addressed packets or return the packet to the system via a software loopback.
OBJECT-TYPE    
  INTEGER software-loopback-active(1), hardware-loopback-active(2)  

ibmxnsidpInReceives 1.3.6.1.4.1.2.6.2.11.5
Total number of IDP datagrams received.
OBJECT-TYPE    
  Counter  

ibmxnsidpBcastInReceives 1.3.6.1.4.1.2.6.2.11.6
Number of IDP broadcast datagrams received.
OBJECT-TYPE    
  Counter  

ibmxnsidpMcastInReceives 1.3.6.1.4.1.2.6.2.11.7
Number of IDP multicast datagrams received.
OBJECT-TYPE    
  Counter  

ibmxnsidpInDiscards 1.3.6.1.4.1.2.6.2.11.8
Number of incoming IDP datagrams discarded due to lack of resources.
OBJECT-TYPE    
  Counter  

ibmxnsidpOutRequests 1.3.6.1.4.1.2.6.2.11.11
Number of IDP datagrams generated by local IDP user protocols. This counter does not include any datagrams counted in ibmxnsidpForwDatagrams.
OBJECT-TYPE    
  Counter  

ibmxnsidpBcastOutRequests 1.3.6.1.4.1.2.6.2.11.12
Number of IDP broadcast datagrams generated by local IDP user protocols. This counter does not include any datagrams counted in ibmxnsidpForwDatagrams.
OBJECT-TYPE    
  Counter  

ibmxnsidpMcastOutRequests 1.3.6.1.4.1.2.6.2.11.13
Number of IDP multicast datagrams generated by local IDP user protocols. This counter does not include any datagrams counted in ibmxnsidpForwDatagrams.
OBJECT-TYPE    
  Counter  

ibmxnsidpForwDatagrams 1.3.6.1.4.1.2.6.2.11.14
Number of IDP datagrams for which an attempt was made to forward.
OBJECT-TYPE    
  Counter  

ibmxnsidpOutDiscards 1.3.6.1.4.1.2.6.2.11.15
Total number of outgoing IDP datagrams discarded.
OBJECT-TYPE    
  Counter  

ibmxnsidpOutNoRoutes 1.3.6.1.4.1.2.6.2.11.16
Number of outgoing IDP datagrams discarded because no route was available to the specified destination.
OBJECT-TYPE    
  Counter  

ibmxnsidpRoutingDiscards 1.3.6.1.4.1.2.6.2.11.17
Number of routing entries discarded even though they were valid.
OBJECT-TYPE    
  Counter  

ibmxnsidpZeroDirBcast 1.3.6.1.4.1.2.6.2.11.19
Number of IDP datagrams forwarded to the system due to zeronet broadcast.
OBJECT-TYPE    
  Counter  

ibmxnsidpTooSmall 1.3.6.1.4.1.2.6.2.11.20
Number of IDP datagrams with len < the size of an IDP header.
OBJECT-TYPE    
  Counter  

ibmxnsidpBadLen 1.3.6.1.4.1.2.6.2.11.21
Number of IDP datagrams with number of bytes in the packet less than the number of bytes specified in the IDP header field.
OBJECT-TYPE    
  Counter  

ibmxnsidpBadSum 1.3.6.1.4.1.2.6.2.11.22
Number of IDP datagrams with a bad checksum
OBJECT-TYPE    
  Counter  

ibmxnsidpBadTTL 1.3.6.1.4.1.2.6.2.11.23
Number of IDP datagrams with TTL value > IDP maximum hopcount of 16.
OBJECT-TYPE    
  Counter  

ibmxnsErrUnspec 1.3.6.1.4.1.2.6.2.11.24
Number of Error packets generated because an IDP datagram was dropped for unspecified reasons.
OBJECT-TYPE    
  Counter  

ibmxnsErrChecksum 1.3.6.1.4.1.2.6.2.11.25
Number of Error packets generated because an IDP datagram was dropped due a bad checksum.
OBJECT-TYPE    
  Counter  

ibmxnsErrUnreach 1.3.6.1.4.1.2.6.2.11.26
Number of Error packets generated because an IDP datagram was dropped due to an unreachable host.
OBJECT-TYPE    
  Counter  

ibmxnsErrTTLExpired 1.3.6.1.4.1.2.6.2.11.27
Number of Error packets generated because an IDP datagram was dropped because its time-to-live counter had expired.
OBJECT-TYPE    
  Counter  

ibmxnsErrTooBig 1.3.6.1.4.1.2.6.2.11.28
Number of Error packets generated because an IDP datagram was dropped because it was too large to be forwarded through this node.
OBJECT-TYPE    
  Counter  

ibmxnsErrResources 1.3.6.1.4.1.2.6.2.11.29
Number of Error packets generated because an IDP datagram was dropped due to lack of resources.
OBJECT-TYPE    
  Counter  

ibmxnsErrCongWarn 1.3.6.1.4.1.2.6.2.11.30
Number of Error packets generated for congestion warnings.
OBJECT-TYPE    
  Counter  

ibmxnsErrCongDiscard 1.3.6.1.4.1.2.6.2.11.31
Number of Error packets generated for congestion discards.
OBJECT-TYPE    
  Counter  

ibmxnsErrSquelched 1.3.6.1.4.1.2.6.2.11.32
Number of error packets that would have been generated, except that the faulted datagram had one of the following conditions: - was sent as link layer broadcast - NS destination was broadcast - NS source was 0, loopback, or broadcast
OBJECT-TYPE    
  Counter  

ibmxnsErrOutMsgs 1.3.6.1.4.1.2.6.2.11.33
Total number of error packets generated.
OBJECT-TYPE    
  Counter  

ibmxnsAddrTable 1.3.6.1.4.1.2.6.2.11.34
The XNS Address Table.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmXnsAddrEntry

ibmxnsAddrEntry 1.3.6.1.4.1.2.6.2.11.34.1
An entry in the XNS address table.
OBJECT-TYPE    
  IbmXnsAddrEntry  

ibmxnsAddrAddress 1.3.6.1.4.1.2.6.2.11.34.1.1
The XNS address to which this entry's addressing information pertains.
OBJECT-TYPE    
  OCTET STRING SIZE(12)  

ibmxnsAddrIfIndex 1.3.6.1.4.1.2.6.2.11.34.1.2
The interface index which identifies the interface to which this entry is applicable.
OBJECT-TYPE    
  INTEGER  

ibmxnsRouteTable 1.3.6.1.4.1.2.6.2.11.35
The XNS Route Table.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmXnsRouteEntry

ibmxnsRouteEntry 1.3.6.1.4.1.2.6.2.11.35.1
An entry in the XNS route table.
OBJECT-TYPE    
  IbmXnsRouteEntry  

ibmxnsRouteDest 1.3.6.1.4.1.2.6.2.11.35.1.1
The desination network of this route.
OBJECT-TYPE    
  OCTET STRING SIZE(12)  

ibmxnsRouteIfIndex 1.3.6.1.4.1.2.6.2.11.35.1.2
The index value which identifies the local interface through which the next hop of this route should be reached.
OBJECT-TYPE    
  INTEGER  

ibmxnsRouteNextHop 1.3.6.1.4.1.2.6.2.11.35.1.3
The XNS network address of the next hop of this route.
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

ibmxnsRouteMetric 1.3.6.1.4.1.2.6.2.11.35.1.4
The hop count to the destination.
OBJECT-TYPE    
  INTEGER  

ibmxnsRouteUse 1.3.6.1.4.1.2.6.2.11.35.1.5
Reference counter for this route.
OBJECT-TYPE    
  Counter  

ibmxnsFilterTable 1.3.6.1.4.1.2.6.2.11.36
The XNS Filter Table.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmXnsFilterEntry

ibmxnsFilterEntry 1.3.6.1.4.1.2.6.2.11.36.1
An entry in the XNS filter table.
OBJECT-TYPE    
  IbmXnsFilterEntry  

ibmxnsFilterIfIndex 1.3.6.1.4.1.2.6.2.11.36.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmxnsFilterNumber 1.3.6.1.4.1.2.6.2.11.36.1.2
A unique integer identifying this filter entry for this interface.
OBJECT-TYPE    
  INTEGER  

ibmxnsFilterValue 1.3.6.1.4.1.2.6.2.11.36.1.3
An octet string representing the IDP header information required by this filter entry. Incoming IDP packets will be bitwise ANDed with the value of ibmxnsFilterMask, and if the result is equal to the value of this object, the packet will be filtered according to the value of ibmxnsFilterType. The structure of an IDP header is as follows: BIT16 checksum BIT16 length BIT8 transport control (ie. hop count) BIT8 packet type BIT32 destination network address BIT48 destination host address BIT16 destination socket BIT32 source network address BIT48 source host address BIT16 source socket
OBJECT-TYPE    
  OCTET STRING SIZE(30)  

ibmxnsFilterMask 1.3.6.1.4.1.2.6.2.11.36.1.4
An octet string indicating the parts of the IDP header relevant to this filter entry. This mask will be bitwise ANDed with the IDP packet; if the result is equal to the value of ibmxnsFilterValue, the packet will be filtered according to the value of ibmxnsFilterType.
OBJECT-TYPE    
  OCTET STRING SIZE(30)  

ibmxnsFilterType 1.3.6.1.4.1.2.6.2.11.36.1.5
Determines whether this filter is a deny entry or a permit entry.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmxnsFilterHCCompare 1.3.6.1.4.1.2.6.2.11.36.1.6
Indicates the relational association desired if filtering is being done based on hop count. If filtering is not being done based on hop count (that is, if the hop count portion of ibmxnsFilterMask is 0) the value of this object will be none(1).
OBJECT-TYPE    
  INTEGER none(1), less-than(2), less-than-equal(3), equal(4), greater-than-equal(5), greater-than(6)  

ibmxnsFilterUse 1.3.6.1.4.1.2.6.2.11.36.1.7
Usage count for this filter entry.
OBJECT-TYPE    
  Counter  

ibmipx 1.3.6.1.4.1.2.6.2.12
OBJECT IDENTIFIER    

ibmipxidpForwarding 1.3.6.1.4.1.2.6.2.12.1
Indicates if this node is acting as an IPX router.
OBJECT-TYPE    
  INTEGER forwarding(1), not-forwarding(2)  

ibmipxConfigTable 1.3.6.1.4.1.2.6.2.12.4
The table of IPX configuration information gathered on a per-interface basis.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmIpxConfigEntry

ibmipxConfigEntry 1.3.6.1.4.1.2.6.2.12.4.1
IPX configuration information for a single interface.
OBJECT-TYPE    
  IbmIpxConfigEntry  

ibmipxPortIfIndex 1.3.6.1.4.1.2.6.2.12.4.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmipxPortStatus 1.3.6.1.4.1.2.6.2.12.4.1.2
The status of the IPX protocol stack on this interface.
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

ibmipxidpChecksum 1.3.6.1.4.1.2.6.2.12.4.1.3
Indicates the type of checksumming being done by IDP.
OBJECT-TYPE    
  INTEGER off(1), header(2), packet(3)  

ibmipxLoopbackActive 1.3.6.1.4.1.2.6.2.12.4.1.5
Indicates if this port will use the hardware to loopback locally addressed packets or return the packet to the system via a software loopback.
OBJECT-TYPE    
  INTEGER software-loopback-active(1), hardware-loopback-active(2)  

ibmipxidpInReceives 1.3.6.1.4.1.2.6.2.12.5
Total number of IDP datagrams received.
OBJECT-TYPE    
  Counter  

ibmipxidpBcastInReceives 1.3.6.1.4.1.2.6.2.12.6
Number of IDP broadcast datagrams received.
OBJECT-TYPE    
  Counter  

ibmipxidpInDiscards 1.3.6.1.4.1.2.6.2.12.8
Number of incoming IDP datagrams discarded due to lack of resources.
OBJECT-TYPE    
  Counter  

ibmipxidpInAddrErrors 1.3.6.1.4.1.2.6.2.12.10
Number of incoming IDP datagrams discarded because the network portion of the address did not match the configured address for this host.
OBJECT-TYPE    
  Counter  

ibmipxidpOutRequests 1.3.6.1.4.1.2.6.2.12.11
Number of IDP datagrams generated by local IDP user protocols. This counter does not include any datagrams counted in ibmipxidpForwDatagrams.
OBJECT-TYPE    
  Counter  

ibmipxidpBcastOutRequests 1.3.6.1.4.1.2.6.2.12.12
Number of IDP broadcast datagrams generated by local IDP user protocols. This counter does not include any datagrams counted in ibmipxidpForwDatagrams.
OBJECT-TYPE    
  Counter  

ibmipxidpForwDatagrams 1.3.6.1.4.1.2.6.2.12.14
Number of IDP datagrams for which an attempt was made to forward.
OBJECT-TYPE    
  Counter  

ibmipxidpOutDiscards 1.3.6.1.4.1.2.6.2.12.15
Total number of outgoing IDP datagrams discarded.
OBJECT-TYPE    
  Counter  

ibmipxidpOutNoRoutes 1.3.6.1.4.1.2.6.2.12.16
Number of outgoing IDP datagrams discarded because no route was available to the specified destination.
OBJECT-TYPE    
  Counter  

ibmipxidpRoutingDiscards 1.3.6.1.4.1.2.6.2.12.17
Number of routing entries discarded even though they were valid.
OBJECT-TYPE    
  Counter  

ibmipxidpZeroDirBcast 1.3.6.1.4.1.2.6.2.12.19
Number of IDP datagrams forwarded to the system due to zeronet broadcast.
OBJECT-TYPE    
  Counter  

ibmipxidpTooSmall 1.3.6.1.4.1.2.6.2.12.20
Number of IDP datagrams with len < the size of an IDP header.
OBJECT-TYPE    
  Counter  

ibmipxidpBadLen 1.3.6.1.4.1.2.6.2.12.21
Number of IDP datagrams with number of bytes in the packet less than the number of bytes specified in the IDP header field.
OBJECT-TYPE    
  Counter  

ibmipxidpBadSum 1.3.6.1.4.1.2.6.2.12.22
Number of IDP datagrams with a bad checksum
OBJECT-TYPE    
  Counter  

ibmipxidpBadTTL 1.3.6.1.4.1.2.6.2.12.23
Number of IDP datagrams with TTL value > IDP maximum hopcount of 16.
OBJECT-TYPE    
  Counter  

ibmipxAddrTable 1.3.6.1.4.1.2.6.2.12.34
The IPX Address Table.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmIpxAddrEntry

ibmipxAddrEntry 1.3.6.1.4.1.2.6.2.12.34.1
An entry in the IPX address table.
OBJECT-TYPE    
  IbmIpxAddrEntry  

ibmipxAddrAddress 1.3.6.1.4.1.2.6.2.12.34.1.1
The IPX address to which this entry's addressing information pertains.
OBJECT-TYPE    
  OCTET STRING SIZE(12)  

ibmipxAddrIfIndex 1.3.6.1.4.1.2.6.2.12.34.1.2
The interface index which identifies the interface to which this entry is applicable.
OBJECT-TYPE    
  INTEGER  

ibmipxRouteTable 1.3.6.1.4.1.2.6.2.12.35
The IPX Route Table.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmIpxRouteEntry

ibmipxRouteEntry 1.3.6.1.4.1.2.6.2.12.35.1
An entry in the IPX route table.
OBJECT-TYPE    
  IbmIpxRouteEntry  

ibmipxRouteDest 1.3.6.1.4.1.2.6.2.12.35.1.1
The desination network of this route.
OBJECT-TYPE    
  OCTET STRING SIZE(12)  

ibmipxRouteIfIndex 1.3.6.1.4.1.2.6.2.12.35.1.2
The index value which identifies the local interface through which the next hop of this route should be reached.
OBJECT-TYPE    
  INTEGER  

ibmipxRouteNextHop 1.3.6.1.4.1.2.6.2.12.35.1.3
The IPX network address of the next hop of this route.
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

ibmipxRouteMetric 1.3.6.1.4.1.2.6.2.12.35.1.4
The hop count to the destination.
OBJECT-TYPE    
  INTEGER  

ibmipxRouteUse 1.3.6.1.4.1.2.6.2.12.35.1.5
Reference counter for this route.
OBJECT-TYPE    
  Counter  

ibmipxFilterTable 1.3.6.1.4.1.2.6.2.12.36
The IPX Filter Table.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmIpxFilterEntry

ibmipxFilterEntry 1.3.6.1.4.1.2.6.2.12.36.1
An entry in the IPX filter table.
OBJECT-TYPE    
  IbmIpxFilterEntry  

ibmipxFilterIfIndex 1.3.6.1.4.1.2.6.2.12.36.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmipxFilterNumber 1.3.6.1.4.1.2.6.2.12.36.1.2
A unique integer identifying this filter entry for this interface.
OBJECT-TYPE    
  INTEGER  

ibmipxFilterValue 1.3.6.1.4.1.2.6.2.12.36.1.3
An octet string representing the IDP header information required by this filter entry. Incoming IDP packets will be bitwise ANDed with the value of ibmipxFilterMask, and if the result is equal to the value of this object, the packet will be filtered according to the value of ibmipxFilterType. The structure of an IDP header is as follows: BIT16 checksum BIT16 length BIT8 transport control (ie. hop count) BIT8 packet type BIT32 destination network address BIT48 destination host address BIT16 destination socket BIT32 source network address BIT48 source host address BIT16 source socket
OBJECT-TYPE    
  OCTET STRING SIZE(30)  

ibmipxFilterMask 1.3.6.1.4.1.2.6.2.12.36.1.4
An octet string indicating the parts of the IDP header relevant to this filter entry. This mask will be bitwise ANDed with the IDP packet; if the result is equal to the value of ibmipxFilterValue, the packet will be filtered according to the value of ibmipxFilterType.
OBJECT-TYPE    
  OCTET STRING SIZE(30)  

ibmipxFilterType 1.3.6.1.4.1.2.6.2.12.36.1.5
Determines whether this filter is a deny entry or a permit entry.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmipxFilterHCCompare 1.3.6.1.4.1.2.6.2.12.36.1.6
Indicates the relational association desired if filtering is being done based on hop count. If filtering is not being done based on hop count (that is, if the hop count portion of ibmipxFilterMask is 0) the value of this object will be none(1).
OBJECT-TYPE    
  INTEGER none(1), less-than(2), less-than-equal(3), equal(4), greater-than-equal(5), greater-than(6)  

ibmipxFilterUse 1.3.6.1.4.1.2.6.2.12.36.1.7
Usage count for this filter entry.
OBJECT-TYPE    
  Counter  

ibmipxsapStatInRequests 1.3.6.1.4.1.2.6.2.12.37
Number of SAP requests received by this entity.
OBJECT-TYPE    
  Counter  

ibmipxsapStatOutRequests 1.3.6.1.4.1.2.6.2.12.38
Number of SAP requests sent by this entity.
OBJECT-TYPE    
  Counter  

ibmipxsapStatInResponses 1.3.6.1.4.1.2.6.2.12.39
Number of SAP responses received by this entity.
OBJECT-TYPE    
  Counter  

ibmipxsapStatOutResponses 1.3.6.1.4.1.2.6.2.12.40
Number of SAP responses sent by this entity.
OBJECT-TYPE    
  Counter  

ibmipxsapStatInErrors 1.3.6.1.4.1.2.6.2.12.41
Number of incoming SAP packets discarded due to errors.
OBJECT-TYPE    
  Counter  

ibmipxsapStatOutDiscards 1.3.6.1.4.1.2.6.2.12.42
Number of outgoing SAP packets discarded due to lack of resources.
OBJECT-TYPE    
  Counter  

ibmipxsapServerTable 1.3.6.1.4.1.2.6.2.12.43
Table of IPX servers.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmIpxsapServerEntry

ibmipxsapServerEntry 1.3.6.1.4.1.2.6.2.12.43.1
Information on a single server.
OBJECT-TYPE    
  IbmIpxsapServerEntry  

ibmipxsapServerType 1.3.6.1.4.1.2.6.2.12.43.1.1
The type of this server.
OBJECT-TYPE    
  INTEGER  

ibmipxsapServerNet 1.3.6.1.4.1.2.6.2.12.43.1.2
The IPX network number of this server.
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

ibmipxsapServerHost 1.3.6.1.4.1.2.6.2.12.43.1.3
The IPX host address of this server.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmipxsapServerSocket 1.3.6.1.4.1.2.6.2.12.43.1.4
The IPX socket number this server uses to advertise its service.
OBJECT-TYPE    
  INTEGER  

ibmipxsapServerName 1.3.6.1.4.1.2.6.2.12.43.1.5
The name of this server.
OBJECT-TYPE    
  DisplayString  

ibmipxsapServerAge 1.3.6.1.4.1.2.6.2.12.43.1.6
The number of seconds since this server entry was updated by the SAP protocol.
OBJECT-TYPE    
  INTEGER  

ibmipxsapServerHops 1.3.6.1.4.1.2.6.2.12.43.1.7
The number of network hops required to reach this server.
OBJECT-TYPE    
  INTEGER  

ibmipxsapServerIfIndex 1.3.6.1.4.1.2.6.2.12.43.1.8
The interface which is used to reach this server. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmipxsapServerIndex 1.3.6.1.4.1.2.6.2.12.43.1.9
A unique number identifying servers advertised at the same IPX network and host address.
OBJECT-TYPE    
  INTEGER  

ibmipxsapServerRequestsFiltered 1.3.6.1.4.1.2.6.2.12.43.1.10
Number of times a request for this server has been filtered.
OBJECT-TYPE    
  Counter  

ibmappn 1.3.6.1.4.1.2.6.2.13
OBJECT IDENTIFIER    

ibmappnNode 1.3.6.1.4.1.2.6.2.13.1
OBJECT IDENTIFIER    

ibmappnGeneralInfoAndCaps 1.3.6.1.4.1.2.6.2.13.1.1
OBJECT IDENTIFIER    

ibmappnNodeCpName 1.3.6.1.4.1.2.6.2.13.1.1.1
Administratively-assigned network name for this node in the format NETID.CPNAME.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnNodeNetid 1.3.6.1.4.1.2.6.2.13.1.1.2
Administratively-assigned APPN network identification, which can be from one to eight characters. This ID is used with the control point name to create a fully-qualified control point name.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnNodeBlockNum 1.3.6.1.4.1.2.6.2.13.1.1.3
The block number is the first three digits of the node_id. These 3 hexadecimal digits identify the product and are not configurable.
OBJECT-TYPE    
  DisplayString SIZE(3)  

ibmappnNodeIdNum 1.3.6.1.4.1.2.6.2.13.1.1.4
The ID number is the last 5 digits of the node_id. These 5 hexadecimal digits are administratively defined and combined with the 3 digit block number form the node_id. This node_id is used to identify the local node and is include in APPN alerts as well as being included in XIDs. A unique value is required for connections to SNA sub-area.
OBJECT-TYPE    
  DisplayString SIZE(5)  

ibmappnNodeType 1.3.6.1.4.1.2.6.2.13.1.1.5
Type of APPN node, either network, len, or end node.
OBJECT-TYPE    
  INTEGER networkNode(1), endNode(2), len(4)  

ibmappnNodeUpTime 1.3.6.1.4.1.2.6.2.13.1.1.6
Time (in hundredths of a second) since this APPN node was initialized.
OBJECT-TYPE    
  TimeTicks  

ibmappnNodeNegotLs 1.3.6.1.4.1.2.6.2.13.1.1.7
Indicates whether this node supports negotiable link stations.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeSegReasm 1.3.6.1.4.1.2.6.2.13.1.1.8
Indicates whether this node supports segment reassembly. This is only supported when segment generation is also supported.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeBindReasm 1.3.6.1.4.1.2.6.2.13.1.1.9
Indicates whether this node supports Bind segment reassembly. This will only be supported when Bind segment generation is also supported.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeParallelTg 1.3.6.1.4.1.2.6.2.13.1.1.10
Indicates whether this node supports parallel TGs.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeService 1.3.6.1.4.1.2.6.2.13.1.1.11
Indicates whether this node allows call-in from nodes not defined locally.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeAdaptiveBindPacing 1.3.6.1.4.1.2.6.2.13.1.1.12
Indicates whether this node supports adaptive bind pacing.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnUniqueInfoAndCaps 1.3.6.1.4.1.2.6.2.13.1.2
OBJECT IDENTIFIER    

ibmappnNodeNnRcvRegChar 1.3.6.1.4.1.2.6.2.13.1.2.1
Indicates whether this node supports receiving registered characteristics.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeNnGateway 1.3.6.1.4.1.2.6.2.13.1.2.2
Indicates whether this is a gateway node.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeNnCentralDirectory 1.3.6.1.4.1.2.6.2.13.1.2.3
Indicates whether this node supports central directory cache.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeNnTreeCache 1.3.6.1.4.1.2.6.2.13.1.2.4
Indicates whether this node supports route tree cache.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeNnTreeUpdate 1.3.6.1.4.1.2.6.2.13.1.2.5
Indicates whether this node supports incremental_tree_update, which is only supported when tree caching is supported.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeNnRouteAddResist 1.3.6.1.4.1.2.6.2.13.1.2.6
Route addition resistance is a value that indicates the relative desirability of using this node for intermediate session traffic. The value, which can be any integer 0-255, is used in route computation. The lower the value, the more desirable the node is for intermediate routing.
OBJECT-TYPE    
  INTEGER  

ibmappnNodeNnIsr 1.3.6.1.4.1.2.6.2.13.1.2.7
Indicates whether the node supports intermediate session routing.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeNnFrsn 1.3.6.1.4.1.2.6.2.13.1.2.8
Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This object is the last FRSN sent in a topology update to adjacent network nodes.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmappnEnUniqueCaps 1.3.6.1.4.1.2.6.2.13.1.3
OBJECT IDENTIFIER    

ibmappnNodeEnSegGen 1.3.6.1.4.1.2.6.2.13.1.3.1
Indicates whether this end node supports segment generation.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeEnModeCosMap 1.3.6.1.4.1.2.6.2.13.1.3.2
Indicates whether this end node supports mode name to COS name mapping.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeEnLocateCdinit 1.3.6.1.4.1.2.6.2.13.1.3.3
Indicates whether this end node supports Locate Cdinit.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeEnSendRegNames 1.3.6.1.4.1.2.6.2.13.1.3.4
Indicates whether the node will register its LUs with the adjacent serving network node: NO - do not register names YES - register names
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeEnSendRegChar 1.3.6.1.4.1.2.6.2.13.1.3.5
Indicates whether this node supports send register characteristics, which is only supported when send registered names is also supported.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnPortInformation 1.3.6.1.4.1.2.6.2.13.1.4
OBJECT IDENTIFIER    

ibmappnNodePortTable 1.3.6.1.4.1.2.6.2.13.1.4.1
The Port table describes the configuration and current status of the ports used by APPN. The type of DLC is included in this table as a pointer to the DLC port specific tables.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNodePortEntry

ibmappnNodePortEntry 1.3.6.1.4.1.2.6.2.13.1.4.1.1
The Port Name is used as the index to this table.
OBJECT-TYPE    
  IbmappnNodePortEntry  

ibmappnNodePortName 1.3.6.1.4.1.2.6.2.13.1.4.1.1.1
Administratively-assigned name for this APPN port. The name can be from one to eight characters.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnNodePortState 1.3.6.1.4.1.2.6.2.13.1.4.1.1.2
Indicates the current state of this port.
OBJECT-TYPE    
  INTEGER inactive(1), pendactive(2), active(3), pendinact(4)  

ibmappnNodePortDlcType 1.3.6.1.4.1.2.6.2.13.1.4.1.1.3
The type of DLC interface, distinguished according to the protocol immediately 'below' this layer.
OBJECT-TYPE    
  INTEGER other(1), sdlc(2), dls(3), socket(4), ethernet(5), tokenRing(6)  

ibmappnNodePortPortType 1.3.6.1.4.1.2.6.2.13.1.4.1.1.4
Identifies the type of line used by this port.
OBJECT-TYPE    
  INTEGER leased(1), switched(2), sharedAccessFacilities(3)  

ibmappnNodePortSIMRIM 1.3.6.1.4.1.2.6.2.13.1.4.1.1.5
Indicates whether Set Initialization Mode (SIM) and Receive Initialization Mode (RIM) are supported.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodePortLsRole 1.3.6.1.4.1.2.6.2.13.1.4.1.1.6
Initial role for LSs activated through this port, where 'abm' indicates asynchronous balance mode.
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), negotiable(3), abm(4)  

ibmappnNodePortMaxRcvBtuSize 1.3.6.1.4.1.2.6.2.13.1.4.1.1.7
Maximum Basic Transmission Size (BTU) that a link station on this port can receive.
OBJECT-TYPE    
  INTEGER  

ibmappnNodePortMaxIframeWindow 1.3.6.1.4.1.2.6.2.13.1.4.1.1.8
Maximum number of I-frames that can be received by the XID sender before an acknowledgement is received.
OBJECT-TYPE    
  INTEGER  

ibmappnNodePortDefLsGoodXids 1.3.6.1.4.1.2.6.2.13.1.4.1.1.9
The total number of successfull XIDs that have occurred on all defined link stations on this port since the last time this port was started.
OBJECT-TYPE    
  Counter  

ibmappnNodePortDefLsBadXids 1.3.6.1.4.1.2.6.2.13.1.4.1.1.10
The total number of unsuccessfull XIDs that have occurred on all defined link stations on this port since the last time this port was started.
OBJECT-TYPE    
  Counter  

ibmappnNodePortDynLsGoodXids 1.3.6.1.4.1.2.6.2.13.1.4.1.1.11
The total number of successfull XIDs that have occurred on all dynamic link stations on this port since the last time this port was started.
OBJECT-TYPE    
  Counter  

ibmappnNodePortDynLsBadXids 1.3.6.1.4.1.2.6.2.13.1.4.1.1.12
The total number of unsuccessfull XIDs that have occurred on all dynamic link stations on this port since the last time this port was started.
OBJECT-TYPE    
  Counter  

ibmappnNodePortSpecific 1.3.6.1.4.1.2.6.2.13.1.4.1.1.13
Identifies the port specific OBJECT IDENTIFIER that can provide additional information.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

ibmappnNodePortIpTable 1.3.6.1.4.1.2.6.2.13.1.4.2
Port table (TCP/IP specific).
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNodePortIpEntry

ibmappnNodePortIpEntry 1.3.6.1.4.1.2.6.2.13.1.4.2.1
The IP Name is used as the index to this table.
OBJECT-TYPE    
  IbmappnNodePortIpEntry  

ibmappnNodePortIpName 1.3.6.1.4.1.2.6.2.13.1.4.2.1.1
Administratively-assigned name for this APPN port. The name can be from one to eight characters.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnNodePortIpPortNum 1.3.6.1.4.1.2.6.2.13.1.4.2.1.2
Local TCP/IP port number.
OBJECT-TYPE    
  INTEGER  

ibmappnNodePortDlsTable 1.3.6.1.4.1.2.6.2.13.1.4.3
Port table (DLS specific).
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNodePortDlsEntry

ibmappnNodePortDlsEntry 1.3.6.1.4.1.2.6.2.13.1.4.3.1
The DLS Name is used as the index to this table.
OBJECT-TYPE    
  IbmappnNodePortDlsEntry  

ibmappnNodePortDlsName 1.3.6.1.4.1.2.6.2.13.1.4.3.1.1
Administratively-assigned name for this APPN DLS port. The name can be from one to eight characters.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnNodePortDlsMac 1.3.6.1.4.1.2.6.2.13.1.4.3.1.2
Local DLS MAC address.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmappnNodePortDlsSap 1.3.6.1.4.1.2.6.2.13.1.4.3.1.3
Local DLS Sap address.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ibmappnNodePortTrTable 1.3.6.1.4.1.2.6.2.13.1.4.4
Port table (Token Ring specific).
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNodePortTrEntry

ibmappnNodePortTrEntry 1.3.6.1.4.1.2.6.2.13.1.4.4.1
The TR Name is used as the index to this table.
OBJECT-TYPE    
  IbmappnNodePortTrEntry  

ibmappnNodePortTrName 1.3.6.1.4.1.2.6.2.13.1.4.4.1.1
Administratively-assigned name for this APPN port. The name can be from one to eight characters.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnNodePortTrMac 1.3.6.1.4.1.2.6.2.13.1.4.4.1.2
Local Token Ring MAC address.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmappnNodePortTrSap 1.3.6.1.4.1.2.6.2.13.1.4.4.1.3
Local Token Ring Sap address.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ibmappnNodePortDlcTraceTable 1.3.6.1.4.1.2.6.2.13.1.4.5
Port table generic DLC trace table.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNodePortDlcTraceEntry

ibmappnNodePortDlcTraceEntry 1.3.6.1.4.1.2.6.2.13.1.4.5.1
The Port name and a dynamic integer are the index to this table.
OBJECT-TYPE    
  IbmappnNodePortDlcTraceEntry  

ibmappnNodePortDlcTracPortName 1.3.6.1.4.1.2.6.2.13.1.4.5.1.1
The Port name associated with this this trace table entry.
OBJECT-TYPE    
  DisplayString  

ibmappnNodePortDlcTracIndex 1.3.6.1.4.1.2.6.2.13.1.4.5.1.2
This index value is updated every time a new trace entry is created which provides a means to retrieve only the updated entries and also provides a simple method of correlating the entries. The table will wrap when the table is full, which will result in previous entries being written over. The mangement station can over come this by retrieving the table using this index to retrieve only the new table entries.
OBJECT-TYPE    
  INTEGER  

ibmappnNodePortDlcTracDlcType 1.3.6.1.4.1.2.6.2.13.1.4.5.1.3
The type of DLC interface, distinguished according to the protocol immediately 'below' this layer.
OBJECT-TYPE    
  INTEGER other(1), sdlc(2), dls(3), socket(4), ethernet(5), tokenRing(6)  

ibmappnNodePortDlcTracLocalAddr 1.3.6.1.4.1.2.6.2.13.1.4.5.1.4
Local address in format described below: other = free form DisplayString ip = ld.ld.ld.ld/2d tr = lx:lx:lx:lx:lx:lx.lx dlsw = lx:lx:lx:lx:lx:lx.lx ethernet = lx:lx:lx:lx:lx:lx.lx
OBJECT-TYPE    
  DisplayString  

ibmappnNodePortDlcTracRemoteAddr 1.3.6.1.4.1.2.6.2.13.1.4.5.1.5
Remote Address in the format described below: other = free form DisplayString ip = ld.ld.ld.ld/2d tr = lx:lx:lx:lx:lx:lx.lx dlsw = lx:lx:lx:lx:lx:lx.lx ethernet = lx:lx:lx:lx:lx:lx.lx
OBJECT-TYPE    
  DisplayString  

ibmappnNodePortDlcTracMsgType 1.3.6.1.4.1.2.6.2.13.1.4.5.1.6
Indicates the type of trace record entry
OBJECT-TYPE    
  INTEGER other(1), unknown(2), request(3), confirm(4), indication(5), response(6)  

ibmappnNodePortDlcTracCmdType 1.3.6.1.4.1.2.6.2.13.1.4.5.1.7
Indicates the command type of the trace entry.
OBJECT-TYPE    
  INTEGER testFrame(1), respFrame(2), curFrame(3), icrFrame(4), respAck(5), dgrmFrame(6), xidFrame(7), contFrame(8), contedFrame(9), iFrame(10), enterBusy(12), exitBusy(13), haltFrame(14), lsHalted(15), restartLs(16), lsRestarted(17), netBioSnq(18), netBioSnr(19), gnetFrame(20), netdFrame(21), oobFrame(22), alterSap(23), testRsp(24), haltLsNow(25), netBioAnq(26), netBioAnr(27), mibLsFrame(28), iamOkay(29), ipTestFrame(2001), ipRespFrame(2002), ipCurFrame(2003), ipIcrFrame(2004), ipRespAck(2005), ipDgrmFrame(2006), ipXidFrame(2007), ipContFrame(2008), ipContedFrame(2009), ipIFrame(2010), ipEnterBusy(2012), ipExitBusy(2013), ipHaltFrame(2014), ipLsHalted(2015), ipRestartLs(2016), ipLsRestarted(2017), ipNetBioSnq(2018), ipNetBioSnr(2019), ipGnetFrame(2020), ipNetdFrame(2021), ipOobFrame(2022), ipAlterSap(2023), ipTestRsp(2024), ipHaltLsNow(2025), ipNetBioAnq(2026), ipNetBioAnr(2027), ipMibLsFrame(2028), ipIamOkay(2029), dlsTestReq(4122), dlsTestRsp(4123), dlsIpm(4124), trTestFrame(6001), trRespFrame(6002), trCurFrame(6003), trIcrFrame(6004), trRespAck(6005), trDgrmFrame(6006), trXidFrame(6007), trContFrame(6008), trContedFrame(6009), trIFrame(6010), trEnterBusy(6012), trExitBusy(6013), trHaltFrame(6014), trLsHalted(6015), trRestartLs(6016), trLsRestarted(6017), trNetBioSnq(6018), trNetBioSnr(6019), trGnetFrame(6020), trNetdFrame(6021), trOobFrame(6022), trAlterSap(6023), trTestRsp(6024), trHaltLsNow(6025), trNetBioAnq(6026), trNetBioAnr(6027), trMibLsFrame(6028), trIamOkay(6029)  

ibmappnNodePortDlcTracUseWan 1.3.6.1.4.1.2.6.2.13.1.4.5.1.8
OBJECT-TYPE    
  INTEGER other(1), notApplicable(2), useUnknown(3), useWan(4), useLan(5)  

ibmappnLinkStationInformation 1.3.6.1.4.1.2.6.2.13.1.5
OBJECT IDENTIFIER    

ibmappnNodeLsTable 1.3.6.1.4.1.2.6.2.13.1.5.1
This table contains detail information about the link station configuration and current status.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNodeLsEntry

ibmappnNodeLsEntry 1.3.6.1.4.1.2.6.2.13.1.5.1.1
This table is indexed by the link station name.
OBJECT-TYPE    
  IbmappnNodeLsEntry  

ibmappnNodeLsName 1.3.6.1.4.1.2.6.2.13.1.5.1.1.1
Administratively-assigned name for the link station. The name can be from one to eight characters.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnNodeLsPortName 1.3.6.1.4.1.2.6.2.13.1.5.1.1.2
Administratively-assigned name for the port. The name can be from one to eight characters.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnNodeLsDlcType 1.3.6.1.4.1.2.6.2.13.1.5.1.1.3
The type of DLC interface, distinguished according to the protocol immediately 'below' this layer.
OBJECT-TYPE    
  INTEGER other(1), sdlc(2), dls(3), socket(4), ethernet(5), tokenRing(6)  

ibmappnNodeLsDynamic 1.3.6.1.4.1.2.6.2.13.1.5.1.1.4
Identifies whether this resource is a dynamic link station. Dynamic link stations are created when adjacent nodes that have not been locally defined establish a connection with this node.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeLsState 1.3.6.1.4.1.2.6.2.13.1.5.1.1.5
State of this link station.
OBJECT-TYPE    
  INTEGER inactive(1), pendactive(2), active(3), pendinact(4)  

ibmappnNodeLsCpName 1.3.6.1.4.1.2.6.2.13.1.5.1.1.6
Fully-qualified name of the adjacent node for this link station. The name can be from three to seventeen characters. Format is netid.cpname.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnNodeLsTgNum 1.3.6.1.4.1.2.6.2.13.1.5.1.1.7
Number associated with the TG to this link station.
OBJECT-TYPE    
  INTEGER  

ibmappnNodeLsLimResource 1.3.6.1.4.1.2.6.2.13.1.5.1.1.8
Indicates whether the link station is a limited resource. If it is, the TG is deactivated when there are no sessions.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeLsMigration 1.3.6.1.4.1.2.6.2.13.1.5.1.1.9
Indicates whether this link station will be used for connections to down-level or migration partners.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeLsBlockNum 1.3.6.1.4.1.2.6.2.13.1.5.1.1.10
The block number is the first three digits of the node_id. These 3 hexideimal digits identify the product and are not configurable.
OBJECT-TYPE    
  DisplayString SIZE(3)  

ibmappnNodeLsIdNum 1.3.6.1.4.1.2.6.2.13.1.5.1.1.11
The ID number is the last 5 digits of the node_id. These 5 hexadecimal digits are administratively defined and combined with the 3 digit block number form the node_id. This node_id is used to identify the local node and is include in APPN alerts as well as being included in XIDs. A unique value is required for connections to SNA sub-area.
OBJECT-TYPE    
  DisplayString SIZE(5)  

ibmappnNodeLsCpCpSession 1.3.6.1.4.1.2.6.2.13.1.5.1.1.12
Indicates whether CP-CP sessions are supported by this link station.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNodeLsTargetPacingCount 1.3.6.1.4.1.2.6.2.13.1.5.1.1.13
Numeric value between 0 and 32767 inclusive indicating the desired pacing window size for BINDs on this TG. The number is significant only when fixed bind pacing is being performed.
OBJECT-TYPE    
  INTEGER  

ibmappnNodeLsMaxSendBtuSize 1.3.6.1.4.1.2.6.2.13.1.5.1.1.14
Numeric value between 0 and 32767 inclusive indicating the desired number of bytes in a Basic Transmission Unit (BTU) that can be sent on this TG. This is an administratively assigned value.
OBJECT-TYPE    
  INTEGER  

ibmappnNodeLsEffCap 1.3.6.1.4.1.2.6.2.13.1.5.1.1.15
The effective capacity is an integer value that indicates the kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776. This is an administratively assigned value associated with the TG using this link station.
OBJECT-TYPE    
  INTEGER  

ibmappnNodeLsConnCost 1.3.6.1.4.1.2.6.2.13.1.5.1.1.16
Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255, which indicates maximum cost. This is an administratively assigned value associated with the TG using this link station.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNodeLsByteCost 1.3.6.1.4.1.2.6.2.13.1.5.1.1.17
Relative cost of transmitting a byte over this link. Range is from 0 (lowest cost) to 255. This is an administratively assigned value associated with the TG using this link station.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNodeLsSecurity 1.3.6.1.4.1.2.6.2.13.1.5.1.1.18
The security is represented as an integer with a range of 1 thru 255 with the most common values enumerated as defined above. This is an administratively assigned value associated with the TG using this link station.
OBJECT-TYPE    
  INTEGER nonsecure(1), publicSwitchedNetwork(32), undergroundCable(64), secureConduit(96), guardedConduit(128), encrypted(160), guardedRadiation(192)  

ibmappnNodeLsDelay 1.3.6.1.4.1.2.6.2.13.1.5.1.1.19
Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with some of the more common values enumerated. This is an administratively assigned value associated with the TG using this link station.
OBJECT-TYPE    
  INTEGER minimum(0), negligible(384), terrestrial(9216), packet(147456), long(294912), maximum(2013265920)  

ibmappnNodeLsUsr1 1.3.6.1.4.1.2.6.2.13.1.5.1.1.20
First user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with the TG using this link station.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNodeLsUsr2 1.3.6.1.4.1.2.6.2.13.1.5.1.1.21
Second user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with the TG using this link station.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNodeLsUsr3 1.3.6.1.4.1.2.6.2.13.1.5.1.1.22
Third user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with the TG using this link station.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNodeLsInXidBytes 1.3.6.1.4.1.2.6.2.13.1.5.1.1.23
Number of XID bytes received.
OBJECT-TYPE    
  Counter  

ibmappnNodeLsInMsgBytes 1.3.6.1.4.1.2.6.2.13.1.5.1.1.24
Number of message (I-frame) bytes received.
OBJECT-TYPE    
  Counter  

ibmappnNodeLsInXidFrames 1.3.6.1.4.1.2.6.2.13.1.5.1.1.25
Number of XID frames received.
OBJECT-TYPE    
  Counter  

ibmappnNodeLsInMsgFrames 1.3.6.1.4.1.2.6.2.13.1.5.1.1.26
Number of message (I-frame) frames received.
OBJECT-TYPE    
  Counter  

ibmappnNodeLsOutXidBytes 1.3.6.1.4.1.2.6.2.13.1.5.1.1.27
Number of XID bytes sent.
OBJECT-TYPE    
  Counter  

ibmappnNodeLsOutMsgBytes 1.3.6.1.4.1.2.6.2.13.1.5.1.1.28
Number of message (I-frame) bytes sent.
OBJECT-TYPE    
  Counter  

ibmappnNodeLsOutXidFrames 1.3.6.1.4.1.2.6.2.13.1.5.1.1.29
Number of XID frames sent.
OBJECT-TYPE    
  Counter  

ibmappnNodeLsOutMsgFrames 1.3.6.1.4.1.2.6.2.13.1.5.1.1.30
Number of message (I-frame) frames sent.
OBJECT-TYPE    
  Counter  

ibmappnNodeLsEchoRsps 1.3.6.1.4.1.2.6.2.13.1.5.1.1.31
Number of responses returned from adjacent link station. A response should be returned for each test frame sent by this node. Test frames are sent to adjacent nodes periodically to verify connectivity and to measure that actual round trip time, that is the time the test frame is sent until the response is received.
OBJECT-TYPE    
  Counter  

ibmappnNodeLsCurrentDelay 1.3.6.1.4.1.2.6.2.13.1.5.1.1.32
The time that it took for the last test signal to be sent and returned from this link station to the adjacent links station. This time is represented in milliseconds.
OBJECT-TYPE    
  INTEGER  

ibmappnNodeLsMaxDelay 1.3.6.1.4.1.2.6.2.13.1.5.1.1.33
The longest time it took for a test signal to be sent and returned from this link station to the adjacent links station. This time is represented in milliseconds .
OBJECT-TYPE    
  INTEGER  

ibmappnNodeLsMinDelay 1.3.6.1.4.1.2.6.2.13.1.5.1.1.34
The shortest time it took for a test signal to be sent and returned from this link station to the adjacent links station. This time is represented in milliseconds.
OBJECT-TYPE    
  INTEGER  

ibmappnNodeLsMaxDelayTime 1.3.6.1.4.1.2.6.2.13.1.5.1.1.35
The time (since system up in hundredth of seconds) when the longest delay occurred. This time can be used to identify when this high water mark occurred in relation to the last initialization of the APPN node.
OBJECT-TYPE    
  TimeTicks  

ibmappnNodeLsGoodXids 1.3.6.1.4.1.2.6.2.13.1.5.1.1.36
The total number of successful XIDs that have occurred on this link station since the time it was started.
OBJECT-TYPE    
  Counter  

ibmappnNodeLsBadXids 1.3.6.1.4.1.2.6.2.13.1.5.1.1.37
The total number of unsuccessful XIDs that have occurred on this link station since the time it was started.
OBJECT-TYPE    
  Counter  

ibmappnNodeLsSpecific 1.3.6.1.4.1.2.6.2.13.1.5.1.1.38
Identifies the DLC specific OBJECT IDENTIFIER that can provide additional information.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

ibmappnNodeLsSubState 1.3.6.1.4.1.2.6.2.13.1.5.1.1.39
State of this link station.
OBJECT-TYPE    
  INTEGER inactive(1), sentReqOpnstn(2), pendXidExch(3), sentActAs(4), sentSetMode(5), active(6), sentDeactAsOrd(7), sentDiscOrd(8), sentDestroyTg(9), sentCreateTg(10), sentConnReq(11), pendRcvConnInd(12), pendSendConnRsp(13), sentConnRsp(14), pendDeact(15)  

ibmappnNodeLsStartTime 1.3.6.1.4.1.2.6.2.13.1.5.1.1.40
The time (in hundredth of seconds) this link station has been active the last time since the time APPN was initialized.
OBJECT-TYPE    
  TimeTicks  

ibmappnNodeLsActiveTime 1.3.6.1.4.1.2.6.2.13.1.5.1.1.41
The time (in hundredth of seconds) this link station has been in the active state. A zero value indicates the link station has never been active.
OBJECT-TYPE    
  TimeTicks  

ibmappnNodeLsCurrentStateTime 1.3.6.1.4.1.2.6.2.13.1.5.1.1.42
The time (in hundredth of seconds) the link station is in the current state.
OBJECT-TYPE    
  TimeTicks  

ibmappnNodeLsIpTable 1.3.6.1.4.1.2.6.2.13.1.5.2
Link station table (TCP/IP specific).
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNodeLsIpEntry

ibmappnNodeLsIpEntry 1.3.6.1.4.1.2.6.2.13.1.5.2.1
The IP Name is used as the index to this table.
OBJECT-TYPE    
  IbmappnNodeLsIpEntry  

ibmappnNodeLsIpName 1.3.6.1.4.1.2.6.2.13.1.5.2.1.1
Administratively-assigned name for this link station. The name can be from one to eight characters.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnNodeLsIpState 1.3.6.1.4.1.2.6.2.13.1.5.2.1.2
State of this link station.
OBJECT-TYPE    
  INTEGER inactive(1), pendactive(2), active(3), pendinact(4)  

ibmappnNodeLsLocalIpAddr 1.3.6.1.4.1.2.6.2.13.1.5.2.1.3
Local IP address.
OBJECT-TYPE    
  IpAddress  

ibmappnNodeLsLocalIpPortNum 1.3.6.1.4.1.2.6.2.13.1.5.2.1.4
Local TCP/IP port number. The default listening port will be administratively assigned and will dynamically change if this node initiates a session with adjacent node.
OBJECT-TYPE    
  INTEGER  

ibmappnNodeLsRemoteIpAddr 1.3.6.1.4.1.2.6.2.13.1.5.2.1.5
Remote IP address.
OBJECT-TYPE    
  IpAddress  

ibmappnNodeLsRemoteIpPortNum 1.3.6.1.4.1.2.6.2.13.1.5.2.1.6
Remote TCP/IP port number.
OBJECT-TYPE    
  INTEGER  

ibmappnNodeLsDlsTable 1.3.6.1.4.1.2.6.2.13.1.5.3
Ls Table (DLS specific).
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNodeLsDlsEntry

ibmappnNodeLsDlsEntry 1.3.6.1.4.1.2.6.2.13.1.5.3.1
The DLS Name is used as the index to this table.
OBJECT-TYPE    
  IbmappnNodeLsDlsEntry  

ibmappnNodeLsDlsName 1.3.6.1.4.1.2.6.2.13.1.5.3.1.1
Administratively-assigned name for this link station. The name can be from one to eight characters.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnNodeLsDlsState 1.3.6.1.4.1.2.6.2.13.1.5.3.1.2
State of this link station.
OBJECT-TYPE    
  INTEGER inactive(1), pendactive(2), active(3), pendinact(4)  

ibmappnNodeLsLocalDlsMac 1.3.6.1.4.1.2.6.2.13.1.5.3.1.3
Local MAC address.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmappnNodeLsLocalDlsSap 1.3.6.1.4.1.2.6.2.13.1.5.3.1.4
Local SAP address.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ibmappnNodeLsRemoteDlsMac 1.3.6.1.4.1.2.6.2.13.1.5.3.1.5
Remote MAC address.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmappnNodeLsRemoteDlsSap 1.3.6.1.4.1.2.6.2.13.1.5.3.1.6
Remote SAP address.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ibmappnNodeLsTrTable 1.3.6.1.4.1.2.6.2.13.1.5.4
Ls Table (Token Ring specific).
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNodeLsTrEntry

ibmappnNodeLsTrEntry 1.3.6.1.4.1.2.6.2.13.1.5.4.1
The TR Name is used as the index to this table.
OBJECT-TYPE    
  IbmappnNodeLsTrEntry  

ibmappnNodeLsTrName 1.3.6.1.4.1.2.6.2.13.1.5.4.1.1
Administratively-assigned name for this link station. The name can be from one to eight characters.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnNodeLsTrState 1.3.6.1.4.1.2.6.2.13.1.5.4.1.2
State of this link station.
OBJECT-TYPE    
  INTEGER inactive(1), pendactive(2), active(3), pendinact(4)  

ibmappnNodeLsLocalTrMac 1.3.6.1.4.1.2.6.2.13.1.5.4.1.3
Local MAC address.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmappnNodeLsLocalTrSap 1.3.6.1.4.1.2.6.2.13.1.5.4.1.4
Local SAP address.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ibmappnNodeLsRemoteTrMac 1.3.6.1.4.1.2.6.2.13.1.5.4.1.5
Remote MAC address.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmappnNodeLsRemoteTrSap 1.3.6.1.4.1.2.6.2.13.1.5.4.1.6
Remote SAP address.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ibmappnNodeLsStatusTable 1.3.6.1.4.1.2.6.2.13.1.5.5
This table contains information related to exceptional and potential exceptional conditions that occur during the activation, XID exchange, and termination of the connection.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNodeLsStatusEntry

ibmappnNodeLsStatusEntry 1.3.6.1.4.1.2.6.2.13.1.5.5.1
This table is indexed by the LsStatusIndex, which is an integer that is continuously updated until it eventually wraps. This provides the management station the ability to retrieve only the updates to the table by using the standard GET NEXT.
OBJECT-TYPE    
  IbmappnNodeLsStatusEntry  

ibmappnNodeLsStatusIndex 1.3.6.1.4.1.2.6.2.13.1.5.5.1.1
Table index. The value of the index begins at zero and is incremented up to a maximum value of 2**31-1 (2,147,483,647) before wrapping.
OBJECT-TYPE    
  INTEGER  

ibmappnNodeLsStatusTime 1.3.6.1.4.1.2.6.2.13.1.5.5.1.2
Time (in hundreds of a second) since this node was last initialized.
OBJECT-TYPE    
  TimeTicks  

ibmappnNodeLsStatusLsName 1.3.6.1.4.1.2.6.2.13.1.5.5.1.3
Administratively-assigned name for this link station.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnNodeLsStatusCpName 1.3.6.1.4.1.2.6.2.13.1.5.5.1.4
Administratively-assigned fully-qualified name of the adjacent node partner. This will be provided when the adjacent node has been defined at this node or when the XID sequence has proceeded far enough to to identify the adjacent node. A blank CP name will indicate the name is unknown.
OBJECT-TYPE    
  DisplayString SIZE(3..18)  

ibmappnNodeLsStatusNodeId 1.3.6.1.4.1.2.6.2.13.1.5.5.1.5
Adjacent Node id
OBJECT-TYPE    
  OCTET STRING  

ibmappnNodeLsStatusTgNum 1.3.6.1.4.1.2.6.2.13.1.5.5.1.6
Number associated with the TG to this link station with a range from 0 to 256. A value of 256 indicates the tg number has not been negotiated and is unknown at this time.
OBJECT-TYPE    
  INTEGER 0..256  

ibmappnNodeLsStatusGeneralSense 1.3.6.1.4.1.2.6.2.13.1.5.5.1.7
The error sense code associated with the start sequence of activation of a link up to the beginning of the XID sequence.
OBJECT-TYPE    
  OCTET STRING  

ibmappnNodeLsStatusNofRetry 1.3.6.1.4.1.2.6.2.13.1.5.5.1.8
Indicates whether NOF will retry the start request to activate the link.
OBJECT-TYPE    
  INTEGER retry(1), noretry(2)  

ibmappnNodeLsStatusEndSense 1.3.6.1.4.1.2.6.2.13.1.5.5.1.9
The sense code associated with the termination of the link connection to adjacent node. This includes all sense information included in the disconnect recieved from the lower layer DLCs and also sense information indicating the link termination originated by upper layer APPN components.
OBJECT-TYPE    
  OCTET STRING  

ibmappnNodeLsStatusXidLocalSense 1.3.6.1.4.1.2.6.2.13.1.5.5.1.10
The error sense code associated with the rejection of the XID.
OBJECT-TYPE    
  OCTET STRING  

ibmappnNodeLsStatusXidRemoteSense 1.3.6.1.4.1.2.6.2.13.1.5.5.1.11
The error sense code adjacent node returned to this node indicating the reason the XID was rejected.
OBJECT-TYPE    
  OCTET STRING  

ibmappnNodeLsStatusXidByteInError 1.3.6.1.4.1.2.6.2.13.1.5.5.1.12
This identifies the actual byte in the XID that caused the error. The value of zero (0) indicates that the variable has no meaning.
OBJECT-TYPE    
  INTEGER na(1000)  

ibmappnNodeLsStatusXidBitInError 1.3.6.1.4.1.2.6.2.13.1.5.5.1.13
This identifies the actual bit within the error byte of the XID. This only has meaning when the byte in error is greater than zero.
OBJECT-TYPE    
  INTEGER na(8)  

ibmappnNodeLsStatusDlcType 1.3.6.1.4.1.2.6.2.13.1.5.5.1.14
This identifies DLC type that was being used when error occurred. This also is used to the format of the local and remote address provided. other = free form DisplayString ip = ld.ld.ld.ld/2d tr = lx:lx:lx:lx:lx:lx.lx dlsw = lx:lx:lx:lx:lx:lx.lx ethernet = lx:lx:lx:lx:lx:lx.lx
OBJECT-TYPE    
  INTEGER other(1), sdlc(2), dls(3), socket(4), ethernet(5), tr(6)  

ibmappnNodeLsStatusLocalAddr 1.3.6.1.4.1.2.6.2.13.1.5.5.1.15
This contains a displayable string that identifies the DLC type and appropriate address. See DlcType above for details of the format.
OBJECT-TYPE    
  DisplayString  

ibmappnNodeLsStatusRemoteAddr 1.3.6.1.4.1.2.6.2.13.1.5.5.1.16
This contains a displayable string that identifies the DLC type and appropriate address. See DlcType above for details of the format.
OBJECT-TYPE    
  DisplayString  

ibmappnSnmpInformation 1.3.6.1.4.1.2.6.2.13.1.6
OBJECT IDENTIFIER    

ibmappnSnmpInPkts 1.3.6.1.4.1.2.6.2.13.1.6.1
Total number of messages delivered to the APPN SNMP sub-agent.
OBJECT-TYPE    
  Counter  

ibmappnSnmpInGetRequests 1.3.6.1.4.1.2.6.2.13.1.6.2
Total number of GET requests delivered to the APPN SNMP sub-agent.
OBJECT-TYPE    
  Counter  

ibmappnSnmpInGetNexts 1.3.6.1.4.1.2.6.2.13.1.6.3
Total number of GETNEXT requests delivered to the APPN SNMP sub-agent.
OBJECT-TYPE    
  Counter  

ibmappnSnmpInSetRequests 1.3.6.1.4.1.2.6.2.13.1.6.4
Total number of SET requests delivered to the APPN SNMP sub-agent.
OBJECT-TYPE    
  Counter  

ibmappnSnmpInTotalVars 1.3.6.1.4.1.2.6.2.13.1.6.5
Total number of VARIABLES included in both GET and GETNEXT requests to the APPN SNMP sub-agent.
OBJECT-TYPE    
  Counter  

ibmappnSnmpInGetVars 1.3.6.1.4.1.2.6.2.13.1.6.6
Total number of VARIBLES included in all GET requests to the APPN SNMP sub-agent.
OBJECT-TYPE    
  Counter  

ibmappnSnmpInGetNextVars 1.3.6.1.4.1.2.6.2.13.1.6.7
Total number of VARIABLES included in all GETNEXT requests to the APPN SNMP sub-agent.
OBJECT-TYPE    
  Counter  

ibmappnSnmpInSetVars 1.3.6.1.4.1.2.6.2.13.1.6.8
Total number of VARIBLES included in all SET requests to the APPN SNMP sub-agent.
OBJECT-TYPE    
  Counter  

ibmappnSnmpOutNoSuchNames 1.3.6.1.4.1.2.6.2.13.1.6.9
Total number of VARIABLES that could not be found by the APPN SNMP sub-agent.
OBJECT-TYPE    
  Counter  

ibmappnSnmpOutGenErrs 1.3.6.1.4.1.2.6.2.13.1.6.10
Total number of undefined errors that occurred processing SNMP request to the APPN SNMP sub-agent.
OBJECT-TYPE    
  Counter  

ibmappnMemoryUse 1.3.6.1.4.1.2.6.2.13.1.7
OBJECT IDENTIFIER    

ibmappnMemorySize 1.3.6.1.4.1.2.6.2.13.1.7.1
Size of the shared storage segment, as obtained by storage management from the underlying operating system.
OBJECT-TYPE    
  INTEGER  

ibmappnMemoryUsed 1.3.6.1.4.1.2.6.2.13.1.7.2
Number of bytes in the segment that are currently allocated to process.
OBJECT-TYPE    
  INTEGER  

ibmappnMemoryWarnThresh 1.3.6.1.4.1.2.6.2.13.1.7.3
Allocation threshold beyond which storage management considers the storage resources to be constrained.
OBJECT-TYPE    
  INTEGER  

ibmappnMemoryCritThresh 1.3.6.1.4.1.2.6.2.13.1.7.4
Allocation threshold beyond which storage management considers the storage resources to be critically constrained.
OBJECT-TYPE    
  INTEGER  

ibmappnXidInformation 1.3.6.1.4.1.2.6.2.13.1.8
OBJECT IDENTIFIER    

ibmappnNodeDefLsGoodXids 1.3.6.1.4.1.2.6.2.13.1.8.1
The current number of successfull XIDs that have occurred on all defined link stations since the last time this node was initialized.
OBJECT-TYPE    
  Counter  

ibmappnNodeDefLsBadXids 1.3.6.1.4.1.2.6.2.13.1.8.2
The current number of unsuccessfull XIDs that have occurred on all defined link stations since the last time this node was initialized.
OBJECT-TYPE    
  Counter  

ibmappnNodeDynLsGoodXids 1.3.6.1.4.1.2.6.2.13.1.8.3
The current number of successfull XIDs that have occurred on all dynamic link stations since the last time this node was initialized.
OBJECT-TYPE    
  Counter  

ibmappnNodeDynLsBadXids 1.3.6.1.4.1.2.6.2.13.1.8.4
The current number of unsuccessfull XIDs that have occurred on all dynamic link stations since the last time this node was initialized.
OBJECT-TYPE    
  Counter  

ibmappnNn 1.3.6.1.4.1.2.6.2.13.2
OBJECT IDENTIFIER    

ibmappnNnTopo 1.3.6.1.4.1.2.6.2.13.2.1
OBJECT IDENTIFIER    

ibmappnNnTopoMaxNodes 1.3.6.1.4.1.2.6.2.13.2.1.1
Maximum number of nodes allowed in the APPN topology database This administratively assigned value must be equal to or greater than the maximum total number of end nodes and network nodes. If the number of nodes exceeds this value, APPN will issue an Alert and the node can no longer participate as a network node.
OBJECT-TYPE    
  INTEGER  

ibmappnNnTopoCurNumNodes 1.3.6.1.4.1.2.6.2.13.2.1.2
Current number of nodes in this node's topology database. If this value exceeds the maximum number of nodes allowed (NnTopoMaxNodes), APPN alert CPDB002 is issued.
OBJECT-TYPE    
  Gauge  

ibmappnNnTopoInTdus 1.3.6.1.4.1.2.6.2.13.2.1.3
Total number of TDUs received from all adjacent NN since last initialization.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoOutTdus 1.3.6.1.4.1.2.6.2.13.2.1.4
Total number of TDUs built by this node to be sent to all adjacent NN since last initialization.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoNodeLowRsns 1.3.6.1.4.1.2.6.2.13.2.1.5
Total number of topology node updates received by this node with a RSN less than the current RSN. Both even and odd RSN are included in this count. These TDUs are not errors, but result when TDUs are broadcast to all adjacent network nodes. No update to this node's topology database occurs, but this node will send a TDU with it's higher RSN to the adjacent node that sent this low RSN.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoNodeEqualRsns 1.3.6.1.4.1.2.6.2.13.2.1.6
Total number of topology node updates received by this node with a RSN equal to the current RSN. Both even and odd RSN are included in this count. These TDUs are not errors, but result when TDUs are broadcast to all adjacent network nodes. No update to this node's topology database occurs.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoNodeGoodHighRsns 1.3.6.1.4.1.2.6.2.13.2.1.7
Total number of topology node updates received by this node with a RSN greater than the current RSN. This results in updating this nodes topology and broadcasting a TDU to all adjacent network nodes. It is not required to send a TDU to the sender of this update because that node already has the update.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoNodeBadHighRsns 1.3.6.1.4.1.2.6.2.13.2.1.8
Total number of topology node updates received by this node with an odd RSN greater than the current RSN. These updates represent a topology inconsistency detected by one of the APPN network nodes. This results in updating this nodes topology and broadcasting a TDU to all adjacent network nodes.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoNodeStateUpdates 1.3.6.1.4.1.2.6.2.13.2.1.9
Total number of topology Node records built as a result of internally detected node state changes that affect APPN topology and routing. Updates are sent via TDUs to all adjacent network nodes.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoNodeErrors 1.3.6.1.4.1.2.6.2.13.2.1.10
Total number of topology node records inconsistencies detected by this node. This occurs when this node attempts to update its topology database and detects a data inconsistency. This node will create a TDU with the current RSN incremented to the next odd number and broadcast it to all adjacent NNs.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoNodeTimerUpdates 1.3.6.1.4.1.2.6.2.13.2.1.11
Total number of topology node records built for this node's resource due to timer updates. Updates are sent via TDUs to all adjacent network nodes. These updates insure other network nodes do not delete this node's resources from their topology database.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoNodePurges 1.3.6.1.4.1.2.6.2.13.2.1.12
Total number of topology node records purged from this node's topology database. This occurs when a node has not been updated in a specified amount of time. The owning node is responsible for broadcasting updates for its resource that it wants kept in the network topology.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoTgLowRsns 1.3.6.1.4.1.2.6.2.13.2.1.13
Total number of topology TG updates received by this node with a RSN less than the current RSN. Both even and odd RSN are included in this count. These TDUs are not errors, but result when TDUs are broadcast to all adjacent network nodes. No update to this node's topology database occurs, but this node will send a TDU with it's higher RSN to the sender of the low RSN.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoTgEqualRsns 1.3.6.1.4.1.2.6.2.13.2.1.14
Total number of topology TG updates received by this node with a RSN equal to the current RSN. Both even and odd RSN are included in this count. These TDUs are not errors, but result when TDUs are broadcast to all adjacent network nodes. No update to this node's topology database occurs.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoTgGoodHighRsns 1.3.6.1.4.1.2.6.2.13.2.1.15
Total number of topology TG updates received by this node with a RSN greater than the current RSN. This results in updating this nodes topology and broadcasting the update to all adjacent network nodes.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoTgBadHighRsns 1.3.6.1.4.1.2.6.2.13.2.1.16
Total number of topology TG updates received by this node with an odd RSN greater than the current RSN. These updates represent a topology inconsistency detected by one of the APPN network nodes. This results in updating this nodes topology and broadcasting a TDU to all adjacent network nodes.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoTgStateUpdates 1.3.6.1.4.1.2.6.2.13.2.1.17
Total number of topology TG records built as a result of internally detected node state changes that affect APPN topology and routing. Updates are sent via TDUs to all adjacent network nodes.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoTgErrors 1.3.6.1.4.1.2.6.2.13.2.1.18
Total number of topology TG records inconsistencies detected by this node. This occurs when this node attempts to update its topology database and detects a data inconsistency. This node will create a TDU with the current RSN incremented to the next odd number and broadcast it to all adjacent NNs.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoTgTimerUpdates 1.3.6.1.4.1.2.6.2.13.2.1.19
Total number of topology TG records built for this node's resource due to timer updates. Updates are sent via TDUs to all adjacent network nodes. These updates insure other network nodes do not delete this node's resources from their topology database.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoTgPurges 1.3.6.1.4.1.2.6.2.13.2.1.20
Total number of topology TG records purged from this node's topology database. This occurs when a TG has not been updated in a specified amount of time. The owning node is responsible for broadcasting updates for its resource that it wants to keep in the network topology.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoTotalRouteCalcs 1.3.6.1.4.1.2.6.2.13.2.1.21
Number of routes calculated for all class of services since the last initialization.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoTotalRouteRejs 1.3.6.1.4.1.2.6.2.13.2.1.22
Number of route requests for all class of services that could not be calculated since last initialization.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoRouteTable 1.3.6.1.4.1.2.6.2.13.2.1.23
Table containing an entry for every Class of Service that it has calculated a route for.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNnTopoRouteEntry

ibmappnNnTopoRouteEntry 1.3.6.1.4.1.2.6.2.13.2.1.23.1
The Class of Service name is the index for this table.
OBJECT-TYPE    
  IbmappnNnTopoRouteEntry  

ibmappnNnTopoRouteCos 1.3.6.1.4.1.2.6.2.13.2.1.23.1.1
The Class of Service for the route.
OBJECT-TYPE    
  DisplayString  

ibmappnNnTopoRouteTrees 1.3.6.1.4.1.2.6.2.13.2.1.23.1.2
Number of routes tree caches built for this Class of Service since the last initialization.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoRouteCalcs 1.3.6.1.4.1.2.6.2.13.2.1.23.1.3
Number of routes calculated since last initialization.
OBJECT-TYPE    
  Counter  

ibmappnNnTopoRouteRejs 1.3.6.1.4.1.2.6.2.13.2.1.23.1.4
Number of route requests that could not be calculated since last initialization.
OBJECT-TYPE    
  Counter  

ibmappnNnAdjNodeTable 1.3.6.1.4.1.2.6.2.13.2.2
Table containing an entry for every node. The information kept in this table is the last FRSN sent and received, the status of the CP-CP sessions, and a gauge that indicates the number of outstanding TDUs.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNnAdjNodeEntry

ibmappnNnAdjNodeEntry 1.3.6.1.4.1.2.6.2.13.2.2.1
The adjacent node name is the index for this table.
OBJECT-TYPE    
  IbmappnNnAdjNodeEntry  

ibmappnNnAdjNodeAdjName 1.3.6.1.4.1.2.6.2.13.2.2.1.1
An administratively-assigned fully-qualified name of this node's adjacent network node.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnNnAdjNodeCpCpSessStatus 1.3.6.1.4.1.2.6.2.13.2.2.1.2
Indicates the state of CP-CP sessions between this node and adjacent network and end nodes. Incative indicates no CP-CP sessions exists between this node and the adjacent node. Active indicates CP-CP sessons are active using both the ConWinner and ConLoser sessions. The session initiated by this node is refered to as the ConWinner session and is used by this node to send to the adjacent node. The ConLoserr session is initiated by the adjacent node and is used by this node to receive from the adjacent node.
OBJECT-TYPE    
  INTEGER active(1), conLoserActive(2), conWinnerActive(3), inactive(4)  

ibmappnNnAdjNodeOutOfSeqTdus 1.3.6.1.4.1.2.6.2.13.2.2.1.3
Number of out of sequence Topology Database Updates (TDUs). In a quiesced state, this value is zero. In normal operation, the value varies depending on the network environment.
OBJECT-TYPE    
  Gauge  

ibmappnNnAdjNodeLastFrsnSent 1.3.6.1.4.1.2.6.2.13.2.2.1.4
Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last TDU sent to this adjacent node.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmappnNnAdjNodeLastFrsnRcvd 1.3.6.1.4.1.2.6.2.13.2.2.1.5
Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last TDU received from this adjacent node.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmappnNnTopology 1.3.6.1.4.1.2.6.2.13.2.3
OBJECT IDENTIFIER    

ibmappnNnTopologyTable 1.3.6.1.4.1.2.6.2.13.2.3.1
Portion of the APPN routing table that describes all of the APPN network nodes and virtual nodes known to this node.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNnTopologyEntry

ibmappnNnTopologyEntry 1.3.6.1.4.1.2.6.2.13.2.3.1.1
The fully-qualified node name is used to index this table.
OBJECT-TYPE    
  IbmappnNnTopologyEntry  

ibmappnNnNodeName 1.3.6.1.4.1.2.6.2.13.2.3.1.1.1
Administratively-assigned network name that is locally defined at each network node in the format NETID.CPNAME.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnNnNodeFrsn 1.3.6.1.4.1.2.6.2.13.2.3.1.1.2
Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last time this resource was updated at this node.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmappnNnNodeEntryTimeLeft 1.3.6.1.4.1.2.6.2.13.2.3.1.1.3
Number of days before deletion of this network node entry. Range is 0-31.
OBJECT-TYPE    
  INTEGER 0..31  

ibmappnNnNodeType 1.3.6.1.4.1.2.6.2.13.2.3.1.1.4
Type of APPN node.
OBJECT-TYPE    
  INTEGER networknode(1), virtualnode(3)  

ibmappnNnNodeRsn 1.3.6.1.4.1.2.6.2.13.2.3.1.1.5
Resource sequence number that is assigned and controlled by the network node that owns this resource. This is always an even 32-bit number unless an error has occurred.
OBJECT-TYPE    
  INTEGER  

ibmappnNnNodeRouteAddResist 1.3.6.1.4.1.2.6.2.13.2.3.1.1.6
Route addition resistance indicates the relative desirability of using this node for intermediate session traffic. The value, which can be any integer 0-255, is used in route computation. The lower the value, the more desirable the node is for intermediate routing.
OBJECT-TYPE    
  INTEGER  

ibmappnNnNodeCongested 1.3.6.1.4.1.2.6.2.13.2.3.1.1.7
Indicates whether this node is congested. This node is not be included in route selection by other nodes when this congestion exists.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnNodeIsrDepleted 1.3.6.1.4.1.2.6.2.13.2.3.1.1.8
Indicates whether intermediate session routing resources are depleted. This node is not included in intermediate route selection by other nodes when resources are depleted.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnNodeEndptDepleted 1.3.6.1.4.1.2.6.2.13.2.3.1.1.9
Indicates whether session endpoint resources are depleted.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnNodeQuiescing 1.3.6.1.4.1.2.6.2.13.2.3.1.1.10
Indicates whether the node is quiescing. This node is not included in route selection by other nodes when the node is quiescing.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnNodeGateway 1.3.6.1.4.1.2.6.2.13.2.3.1.1.11
Indicates whether the node provide gateway functions.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnNodeCentralDirectory 1.3.6.1.4.1.2.6.2.13.2.3.1.1.12
Indicates whether the node is central directory.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnNodeIsr 1.3.6.1.4.1.2.6.2.13.2.3.1.1.13
Indicates whether the node supports intermediate session routing (ISR).
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnNodeChainSupport 1.3.6.1.4.1.2.6.2.13.2.3.1.1.14
Indicates whether the node supports chaining.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnTgTopologyTable 1.3.6.1.4.1.2.6.2.13.2.3.2
Portion of the APPN topology database that describes all of the APPN transmissions groups used by the APPN network nodes.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNnTgTopologyEntry

ibmappnNnTgTopologyEntry 1.3.6.1.4.1.2.6.2.13.2.3.2.1
This table requires three indexes to provide a unique index. The indexes are the owning or originating CPname, the destination CPname, and the TG number.
OBJECT-TYPE    
  IbmappnNnTgTopologyEntry  

ibmappnNnTgOwner 1.3.6.1.4.1.2.6.2.13.2.3.2.1.1
Administratively-assigned name for the originating node for this TG. The format is NETID.CPNAME and is the same name specified in the node table.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnNnTgDest 1.3.6.1.4.1.2.6.2.13.2.3.2.1.2
Administratively-assigned fully-qualified network name for the destination node for this TG.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnNnTgNum 1.3.6.1.4.1.2.6.2.13.2.3.2.1.3
Number associated with this transmission group. Range is 0-255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNnTgFrsn 1.3.6.1.4.1.2.6.2.13.2.3.2.1.4
Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last time this resource was updated at this node.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmappnNnTgEntryTimeLeft 1.3.6.1.4.1.2.6.2.13.2.3.2.1.5
Number of days before deletion of this network node TG entry. Range is 0-31.
OBJECT-TYPE    
  INTEGER 0..31  

ibmappnNnTgDestVirtual 1.3.6.1.4.1.2.6.2.13.2.3.2.1.6
Indicates whether the destination node is a virtual node.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnTgDlcData 1.3.6.1.4.1.2.6.2.13.2.3.2.1.7
DLC specific data related to the link connection network. Token-Ring - MAC/SAP X.25 Switched - dial digits X.21 Switched - dial digits Circuit Swtch - dial digits
OBJECT-TYPE    
  OCTET STRING SIZE(0..9)  

ibmappnNnTgRsn 1.3.6.1.4.1.2.6.2.13.2.3.2.1.8
Current owning node's resource sequence number for this resource.
OBJECT-TYPE    
  INTEGER  

ibmappnNnTgOperational 1.3.6.1.4.1.2.6.2.13.2.3.2.1.9
Indicates whether the transmission group is operational.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnTgQuiescing 1.3.6.1.4.1.2.6.2.13.2.3.2.1.10
Indicates whether the transmission group is quiescing.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnTgCpCpSession 1.3.6.1.4.1.2.6.2.13.2.3.2.1.11
Indicates whether CP-CP sessions are supported on this TG.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnTgEffCap 1.3.6.1.4.1.2.6.2.13.2.3.2.1.12
The effective capacity is an integer value that indicates the kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER  

ibmappnNnTgConnCost 1.3.6.1.4.1.2.6.2.13.2.3.2.1.13
Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255, which indicates maximum cost. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNnTgByteCost 1.3.6.1.4.1.2.6.2.13.2.3.2.1.14
Relative cost of transmitting a byte over this link. Range is from 0 (lowest cost) to 255. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNnTgSecurity 1.3.6.1.4.1.2.6.2.13.2.3.2.1.15
The security is represented as an integer with a range of 1 thru 255 with the most common values enumerated as defined above. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER nonsecure(1), publicSwitchedNetwork(32), undergroundCable(64), secureConduit(96), guardedConduit(128), encrypted(160), guardedRadiation(192)  

ibmappnNnTgDelay 1.3.6.1.4.1.2.6.2.13.2.3.2.1.16
Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with some of the more common values enumerated. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER minimum(0), negligible(384), terrestrial(9216), packet(147456), long(294912), maximum(2013265920)  

ibmappnNnTgModemClass 1.3.6.1.4.1.2.6.2.13.2.3.2.1.17
This is used to have multiple images for a connection network. For a connection network it is the same as in the TG vector; for a non-connection network it is X'00'.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmappnNnTgUsr1 1.3.6.1.4.1.2.6.2.13.2.3.2.1.18
First user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNnTgUsr2 1.3.6.1.4.1.2.6.2.13.2.3.2.1.19
Second user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNnTgUsr3 1.3.6.1.4.1.2.6.2.13.2.3.2.1.20
Third user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNnTopologyFRTable 1.3.6.1.4.1.2.6.2.13.2.3.3
Portion of the APPN routing table that describes all of the APPN network nodes and virtual nodes known to this node.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNnTopologyFREntry

ibmappnNnTopologyFREntry 1.3.6.1.4.1.2.6.2.13.2.3.3.1
The fully-qualified node name is used to index this table.
OBJECT-TYPE    
  IbmappnNnTopologyFREntry  

ibmappnNnNodeFRName 1.3.6.1.4.1.2.6.2.13.2.3.3.1.1
Administratively-assigned network name that is locally defined at each network node in the format NETID.CPNAME.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnNnNodeFRFrsn 1.3.6.1.4.1.2.6.2.13.2.3.3.1.2
Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last time this resource was updated at this node.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmappnNnNodeFREntryTimeLeft 1.3.6.1.4.1.2.6.2.13.2.3.3.1.3
Number of days before deletion of this network node entry. Range is 0-31.
OBJECT-TYPE    
  INTEGER 0..31  

ibmappnNnNodeFRType 1.3.6.1.4.1.2.6.2.13.2.3.3.1.4
Type of APPN node.
OBJECT-TYPE    
  INTEGER networknode(1), virtualnode(3)  

ibmappnNnNodeFRRsn 1.3.6.1.4.1.2.6.2.13.2.3.3.1.5
Resource sequence number that is assigned and controlled by the network node that owns this resource. This is always an even 32-bit number unless an error has occurred.
OBJECT-TYPE    
  INTEGER  

ibmappnNnNodeFRRouteAddResist 1.3.6.1.4.1.2.6.2.13.2.3.3.1.6
Route addition resistance indicates the relative desirability of using this node for intermediate session traffic. The value, which can be any integer 0-255, is used in route computation. The lower the value, the more desirable the node is for intermediate routing.
OBJECT-TYPE    
  INTEGER  

ibmappnNnNodeFRCongested 1.3.6.1.4.1.2.6.2.13.2.3.3.1.7
Indicates whether this node is congested. This node is not be included in route selection by other nodes when this congestion exists.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnNodeFRIsrDepleted 1.3.6.1.4.1.2.6.2.13.2.3.3.1.8
Indicates whether intermediate session routing resources are depleted. This node is not included in intermediate route selection by other nodes when resources are depleted.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnNodeFREndptDepleted 1.3.6.1.4.1.2.6.2.13.2.3.3.1.9
Indicates whether session endpoint resources are depleted.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnNodeFRQuiescing 1.3.6.1.4.1.2.6.2.13.2.3.3.1.10
Indicates whether the node is quiescing. This node is not included in route selection by other nodes when the node is quiescing.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnNodeFRGateway 1.3.6.1.4.1.2.6.2.13.2.3.3.1.11
Indicates whether the node provide gateway functions.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnNodeFRCentralDirectory 1.3.6.1.4.1.2.6.2.13.2.3.3.1.12
Indicates whether the node is central directory.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnNodeFRIsr 1.3.6.1.4.1.2.6.2.13.2.3.3.1.13
Indicates whether the node supports intermediate session routing (ISR).
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnNodeFRChainSupport 1.3.6.1.4.1.2.6.2.13.2.3.3.1.14
Indicates whether the node supports chaining.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnTgTopologyFRTable 1.3.6.1.4.1.2.6.2.13.2.3.4
Portion of the APPN topology database that describes all of the APPN transmissions groups used by the APPN network nodes.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnNnTgTopologyFREntry

ibmappnNnTgTopologyFREntry 1.3.6.1.4.1.2.6.2.13.2.3.4.1
This table is indexed by four columns: FRSN, TG owner fully-qualified node name, TG destination fully-qualified node name, TG number.
OBJECT-TYPE    
  IbmappnNnTgTopologyFREntry  

ibmappnNnTgFROwner 1.3.6.1.4.1.2.6.2.13.2.3.4.1.1
Administratively-assigned name for the originating node for this TG. The format is NETID.CPNAME and is the same name specified in the node table.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnNnTgFRDest 1.3.6.1.4.1.2.6.2.13.2.3.4.1.2
Administratively-assigned fully-qualified network name for the destination node for this TG.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnNnTgFRNum 1.3.6.1.4.1.2.6.2.13.2.3.4.1.3
Number associated with this transmission group. Range is 0-255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNnTgFRFrsn 1.3.6.1.4.1.2.6.2.13.2.3.4.1.4
Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last time this resource was updated at this node.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmappnNnTgFREntryTimeLeft 1.3.6.1.4.1.2.6.2.13.2.3.4.1.5
Number of days before deletion of this network node TG entry. Range is 0-31.
OBJECT-TYPE    
  INTEGER 0..31  

ibmappnNnTgFRDestVirtual 1.3.6.1.4.1.2.6.2.13.2.3.4.1.6
Indicates whether the destination node is a virtual node.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnTgFRDlcData 1.3.6.1.4.1.2.6.2.13.2.3.4.1.7
DLC specific data related to the link connection network. Token-Ring - MAC/SAP X.25 Switched - dial digits X.21 Switched - dial digits Circuit Swtch - dial digits
OBJECT-TYPE    
  OCTET STRING SIZE(0..9)  

ibmappnNnTgFRRsn 1.3.6.1.4.1.2.6.2.13.2.3.4.1.8
Current owning node's resource sequence number for this resource.
OBJECT-TYPE    
  INTEGER  

ibmappnNnTgFROperational 1.3.6.1.4.1.2.6.2.13.2.3.4.1.9
Indicates whether the transmission group is operational.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnTgFRQuiescing 1.3.6.1.4.1.2.6.2.13.2.3.4.1.10
Indicates whether the transmission group is quiescing.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnTgFRCpCpSession 1.3.6.1.4.1.2.6.2.13.2.3.4.1.11
Indicates whether CP-CP sessions are supported on this TG.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnNnTgFREffCap 1.3.6.1.4.1.2.6.2.13.2.3.4.1.12
The effective capacity is an integer value that indicates the kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER  

ibmappnNnTgFRConnCost 1.3.6.1.4.1.2.6.2.13.2.3.4.1.13
Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255, which indicates maximum cost. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNnTgFRByteCost 1.3.6.1.4.1.2.6.2.13.2.3.4.1.14
Relative cost of transmitting a byte over this link. Range is from 0 (lowest cost) to 255. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNnTgFRSecurity 1.3.6.1.4.1.2.6.2.13.2.3.4.1.15
The security is represented as an integer with a range of 1 thru 255 with the most common values enumerated as defined above. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER nonsecure(1), publicSwitchedNetwork(32), undergroundCable(64), secureConduit(96), guardedConduit(128), encrypted(160), guardedRadiation(192)  

ibmappnNnTgFRDelay 1.3.6.1.4.1.2.6.2.13.2.3.4.1.16
Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with some of the more common values enumerated. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER minimum(0), negligible(384), terrestrial(9216), packet(147456), long(294912), maximum(2013265920)  

ibmappnNnTgFRModemClass 1.3.6.1.4.1.2.6.2.13.2.3.4.1.17
This is used to have multiple images for a connection network. For a connection network it is the same as in the TG vector; for a non-connection network it is X'00'.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmappnNnTgFRUsr1 1.3.6.1.4.1.2.6.2.13.2.3.4.1.18
First user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNnTgFRUsr2 1.3.6.1.4.1.2.6.2.13.2.3.4.1.19
Second user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnNnTgFRUsr3 1.3.6.1.4.1.2.6.2.13.2.3.4.1.20
Third user-defined TG characteristic for this TG with a range of 0-255. This is an administratively assigned value associated with this TG.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnLocalTopology 1.3.6.1.4.1.2.6.2.13.3
OBJECT IDENTIFIER    

ibmappnLocalThisNode 1.3.6.1.4.1.2.6.2.13.3.1
OBJECT IDENTIFIER    

ibmappnLocalGeneral 1.3.6.1.4.1.2.6.2.13.3.1.1
OBJECT IDENTIFIER    

ibmappnLocalNodeName 1.3.6.1.4.1.2.6.2.13.3.1.1.1
Administratively-assigned fully-qualified name for this node. Format is NETID.CPNAME.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnLocalNodeType 1.3.6.1.4.1.2.6.2.13.3.1.1.2
Type of APPN node.
OBJECT-TYPE    
  INTEGER networknode(1), endnode(2), len(4)  

ibmappnLocalNnSpecific 1.3.6.1.4.1.2.6.2.13.3.1.2
OBJECT IDENTIFIER    

ibmappnLocalNnRsn 1.3.6.1.4.1.2.6.2.13.3.1.2.1
Resource sequence number is assigned and controlled by the network node that owns this resource. This is always an even unsigned number unless an error has occurred.
OBJECT-TYPE    
  INTEGER  

ibmappnLocalNnRouteAddResist 1.3.6.1.4.1.2.6.2.13.3.1.2.2
Route addition resistance indicates the relative desirability of using this node for intermediate session traffic. The value, which can be any integer 0-255, is used in route computation. The lower the value, the more desirable the node is for intermediate routing.
OBJECT-TYPE    
  INTEGER  

ibmappnLocalNnCongested 1.3.6.1.4.1.2.6.2.13.3.1.2.3
Indicates whether this node is congested. Other network nodes stop routing traffic to this node while this flag is on.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnLocalNnIsrDepleted 1.3.6.1.4.1.2.6.2.13.3.1.2.4
Indicate whether intermediated session routing resources are depleted. Other network nodes stop routing traffic through this node while this flag is on.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnLocalNnEndptDepleted 1.3.6.1.4.1.2.6.2.13.3.1.2.5
Indicates whether session endpoint resources are depleted.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnLocalNnQuiescing 1.3.6.1.4.1.2.6.2.13.3.1.2.6
Indicates whether the node is quiescing.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnLocalNnGateway 1.3.6.1.4.1.2.6.2.13.3.1.2.7
Indicates whether the node is a gateway.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnLocalNnCentralDirectory 1.3.6.1.4.1.2.6.2.13.3.1.2.8
Indicates whether the node is a central directory.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnLocalNnIsr 1.3.6.1.4.1.2.6.2.13.3.1.2.9
Indicates whether the node supports intermediate session routing.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnLocalNnChainSupport 1.3.6.1.4.1.2.6.2.13.3.1.2.10
Indicates whether the node supports chaining.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnLocalNnFrsn 1.3.6.1.4.1.2.6.2.13.3.1.2.11
Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This object is the last FRSN sent in a topology update to adjacent network nodes.
OBJECT-TYPE    
  INTEGER  

ibmappnLocalTg 1.3.6.1.4.1.2.6.2.13.3.1.3
OBJECT IDENTIFIER    

ibmappnLocalTgTable 1.3.6.1.4.1.2.6.2.13.3.1.3.1
TG Table describes all of the TGs owned by this node. The TG destination can be a virtual node, network node, len, or end node.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnLocalTgEntry

ibmappnLocalTgEntry 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1
This table is indexed by the destination CPname and the TG number.
OBJECT-TYPE    
  IbmappnLocalTgEntry  

ibmappnLocalTgDest 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.1
Administratively-assigned name for the destination node for this TG. This is the fully-qualified network node name.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnLocalTgNum 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.2
Number associated with this transmission group.
OBJECT-TYPE    
  INTEGER  

ibmappnLocalTgDestVirtual 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.3
Indicates whether the destination node is a Virtual node.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnLocalTgDlcData 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.4
DLC specific data related to the link connection network. Token-Ring - MAC/SAP X.25 Switched - dial digits X.21 Switched - dial digits Circuit Swtch - dial digits
OBJECT-TYPE    
  OCTET STRING SIZE(0..9)  

ibmappnLocalTgRsn 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.5
The resource sequence number is assigned and controlled by the network node that owns this resource. This is always an even unsigned number unless an error has occurred.
OBJECT-TYPE    
  INTEGER  

ibmappnLocalTgQuiescing 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.6
Indicates whether the Transmission Group is quiescing.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnLocalTgOperational 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.7
Indicates whether the Transmission Group is operational.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnLocalTgCpCpSession 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.8
Indicates whether the CP-CP Sessions are supported on this TG.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnLocalTgEffCap 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.9
The effective capacity is an integer value that indicates the actual kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776.
OBJECT-TYPE    
  INTEGER  

ibmappnLocalTgConnCost 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.10
Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnLocalTgByteCost 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.11
Relative cost of transmitting a byte over this link. Range is from 0 (lowest cost) to 255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnLocalTgSecurity 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.12
Security level for this TG.
OBJECT-TYPE    
  INTEGER nonsecure(1), publicSwitchedNetwork(32), undergroundCable(64), secureConduit(96), guardedConduit(128), encrypted(160), guardedRadiation(192)  

ibmappnLocalTgDelay 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.13
Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with some of the more common values enumerated.
OBJECT-TYPE    
  INTEGER minimum(0), negligible(384), terrestrial(9216), packet(147456), long(294912), maximum(2013265920)  

ibmappnLocalTgModemClass 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.14
This is used to have multiple images for a connection network. For a connection network it is the same as in the TG vector and for a non-connection network it is zero.
OBJECT-TYPE    
  INTEGER  

ibmappnLocalTgUsr1 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.15
Value of the first user-defined TG characteristic for this TG. Range is 0-255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnLocalTgUsr2 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.16
Value of the second user-defined TG characteristic for this TG. Range is 0-255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnLocalTgUsr3 1.3.6.1.4.1.2.6.2.13.3.1.3.1.1.17
Value of the third user-defined TG characteristic for this TG. Range is 0-255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnLocalEnTopology 1.3.6.1.4.1.2.6.2.13.3.2
OBJECT IDENTIFIER    

ibmappnLocalEnTable 1.3.6.1.4.1.2.6.2.13.3.2.1
Portion of the APPN topology database that describes the end nodes known to this node.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnLocalEnEntry

ibmappnLocalEnEntry 1.3.6.1.4.1.2.6.2.13.3.2.1.1
This table is indexed by the end node CPname.
OBJECT-TYPE    
  IbmappnLocalEnEntry  

ibmappnLocalEnName 1.3.6.1.4.1.2.6.2.13.3.2.1.1.1
Administratively-assigned fully-qualified name of end node in the format NETID.CPNAME.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnLocalEnEntryTimeLeft 1.3.6.1.4.1.2.6.2.13.3.2.1.1.2
Number of days before deletion of this end node entry. Range is 0-31.
OBJECT-TYPE    
  INTEGER 0..31  

ibmappnLocalEnType 1.3.6.1.4.1.2.6.2.13.3.2.1.1.3
Type of APPN node (must always be a len or end node).
OBJECT-TYPE    
  INTEGER endnode(2), len(4)  

ibmappnLocalEnTgTable 1.3.6.1.4.1.2.6.2.13.3.2.2
Table describing all of the TGs owned by the end nodes known to this node. The TG destination can be a virtual node, network node, or end node.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnLocalEnTgEntry

ibmappnLocalEnTgEntry 1.3.6.1.4.1.2.6.2.13.3.2.2.1
This table requires multiple indexes to uniquely identify each TG. They are originating CPname, destination CPname, and the TG number.
OBJECT-TYPE    
  IbmappnLocalEnTgEntry  

ibmappnLocalEnTgOrigin 1.3.6.1.4.1.2.6.2.13.3.2.2.1.1
Administratively-assigned name for the origination node for this TG. This is the fully-qualified network name.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnLocalEnTgDest 1.3.6.1.4.1.2.6.2.13.3.2.2.1.2
Administratively-assigned name for the destination node for this TG. This is the fully-qualified network name.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnLocalEnTgNum 1.3.6.1.4.1.2.6.2.13.3.2.2.1.3
Number associated with this transmission group.
OBJECT-TYPE    
  INTEGER  

ibmappnLocalEnTgEntryTimeLeft 1.3.6.1.4.1.2.6.2.13.3.2.2.1.4
Number of days before deletion of this end node TG entry. Range is 0-31.
OBJECT-TYPE    
  INTEGER 0..31  

ibmappnLocalEnTgDestVirtual 1.3.6.1.4.1.2.6.2.13.3.2.2.1.5
Indicates whether the destination node is a virtual node.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnLocalEnTgDlcData 1.3.6.1.4.1.2.6.2.13.3.2.2.1.6
DLC specific data related to the link connection network. Token-Ring - MAC/SAP X.25 Switched - dial digits X.21 Switched - dial digits Circuit Swtch - dial digits
OBJECT-TYPE    
  OCTET STRING  

ibmappnLocalEnTgOperational 1.3.6.1.4.1.2.6.2.13.3.2.2.1.7
Indicates whether the Transmission Group is operational.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnLocalEnTgCpCpSession 1.3.6.1.4.1.2.6.2.13.3.2.2.1.8
Indicates whether CP-CP sessions are supported on this TG.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnLocalEnTgEffCap 1.3.6.1.4.1.2.6.2.13.3.2.2.1.9
The effective capacity is an integer value that indicates the actual kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776.
OBJECT-TYPE    
  INTEGER  

ibmappnLocalEnTgConnCost 1.3.6.1.4.1.2.6.2.13.3.2.2.1.10
Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnLocalEnTgByteCost 1.3.6.1.4.1.2.6.2.13.3.2.2.1.11
Relative cost of transmitting a byte over this link. Range is from 0, which means no cost, to 255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnLocalEnTgSecurity 1.3.6.1.4.1.2.6.2.13.3.2.2.1.12
Security level for this TG.
OBJECT-TYPE    
  INTEGER nonsecure(1), publicSwitchedNetwork(32), undergroundCable(64), secureConduit(96), guardedConduit(128), encrypted(160), guardedRadiation(192)  

ibmappnLocalEnTgDelay 1.3.6.1.4.1.2.6.2.13.3.2.2.1.13
Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with some of the more common values enumerated.
OBJECT-TYPE    
  INTEGER minimum(0), negligible(384), terrestrial(9216), packet(147456), long(294912), maximum(2013265920)  

ibmappnLocalEnTgModemClass 1.3.6.1.4.1.2.6.2.13.3.2.2.1.14
This is used to have multiple images for a connection network. For a connection network it is the same as in the TG vector and for a non connection network it is zero.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmappnLocalEnTgUsr1 1.3.6.1.4.1.2.6.2.13.3.2.2.1.15
First user-defined TG characteristic for this TG. Range of values is 0-255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnLocalEnTgUsr2 1.3.6.1.4.1.2.6.2.13.3.2.2.1.16
Second user-defined TG characteristic for this TG. Range of values is 0-255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnLocalEnTgUsr3 1.3.6.1.4.1.2.6.2.13.3.2.2.1.17
Third user-defined TG characteristic for this TG. Range of values is 0-255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnDir 1.3.6.1.4.1.2.6.2.13.5
OBJECT IDENTIFIER    

ibmappnDirPerf 1.3.6.1.4.1.2.6.2.13.5.1
OBJECT IDENTIFIER    

ibmappnDirMaxCaches 1.3.6.1.4.1.2.6.2.13.5.1.1
Maximum number of cache entries allowed. This is an administratively assigned value.
OBJECT-TYPE    
  INTEGER  

ibmappnDirCurCaches 1.3.6.1.4.1.2.6.2.13.5.1.2
Current number of cache entries.
OBJECT-TYPE    
  Gauge  

ibmappnDirCurHomeEntries 1.3.6.1.4.1.2.6.2.13.5.1.3
Current number of home entries.
OBJECT-TYPE    
  Gauge  

ibmappnDirRegEntries 1.3.6.1.4.1.2.6.2.13.5.1.4
Current number of registered entries.
OBJECT-TYPE    
  Gauge  

ibmappnDirInLocates 1.3.6.1.4.1.2.6.2.13.5.1.5
Number of directed locates received.
OBJECT-TYPE    
  Counter  

ibmappnDirInBcastLocates 1.3.6.1.4.1.2.6.2.13.5.1.6
Number of broadcast locates received.
OBJECT-TYPE    
  Counter  

ibmappnDirOutLocates 1.3.6.1.4.1.2.6.2.13.5.1.7
Number of directed locates sent.
OBJECT-TYPE    
  Counter  

ibmappnDirOutBcastLocates 1.3.6.1.4.1.2.6.2.13.5.1.8
Number of broadcast locates sent.
OBJECT-TYPE    
  Counter  

ibmappnDirNotFoundLocates 1.3.6.1.4.1.2.6.2.13.5.1.9
Number of directed locates returned with a 'not found'.
OBJECT-TYPE    
  Counter  

ibmappnDirNotFoundBcastLocates 1.3.6.1.4.1.2.6.2.13.5.1.10
Number of broadcast locates returned with a not found.
OBJECT-TYPE    
  Counter  

ibmappnDirLocateOutstands 1.3.6.1.4.1.2.6.2.13.5.1.11
Current number of outstanding locates, both directed and broadcast. This value varies. A value of zero indicates that no locates are unanswered.
OBJECT-TYPE    
  Gauge  

ibmappnDirTable 1.3.6.1.4.1.2.6.2.13.5.2
Table containing information about all known LUs and TPs.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnDirEntry

ibmappnDirEntry 1.3.6.1.4.1.2.6.2.13.5.2.1
This table is indexed by the LU name.
OBJECT-TYPE    
  IbmappnDirEntry  

ibmappnDirLuName 1.3.6.1.4.1.2.6.2.13.5.2.1.1
Fully-qualified network LU name in the domain of the serving network node.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnDirServerName 1.3.6.1.4.1.2.6.2.13.5.2.1.2
Fully-qualified control point (CP) name of the network node server. For unassociated end node entries, the end node fully-qualified name is returned.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnDirLuOwnerName 1.3.6.1.4.1.2.6.2.13.5.2.1.3
Fully-qualified CP name of the node at which the LU is located. This name is the same as the serving NN name when the LU is located at a network node or an unassociated end node. It is also the same as the fully-qualified LU name when this is the control point LU for this node.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnDirLuLocation 1.3.6.1.4.1.2.6.2.13.5.2.1.4
Specifies the location of the LU.
OBJECT-TYPE    
  INTEGER local(1), domain(2), xdomain(3)  

ibmappnDirType 1.3.6.1.4.1.2.6.2.13.5.2.1.5
Directory types are: 1 - Home The LU is in the domain of the local network node and the LU information has been configured at the local node. 2 - Cache The LU has previously been located by a broadcast search and the location information has been saved. 3 - Register The LU is at an end node that is in the domain of the local network node. Registered entries are registered by the served end node.
OBJECT-TYPE    
  INTEGER home(1), cache(2), registered(3)  

ibmappnDirWildCard 1.3.6.1.4.1.2.6.2.13.5.2.1.6
1 - Other means unknown type of LU entry. 2 - Expliced-entry means the full LUNAME will be used for locating this LU. 3 - Partial-wildcard means only the non-blank portions of the LUNAME will be used for locating this LU. 4 - Full-wildcard means all LUNAMES will be directed to this LU.
OBJECT-TYPE    
  INTEGER other(1), explicit-entry(2), partial-wildcard(3), full-wildcard(4)  

ibmappnCos 1.3.6.1.4.1.2.6.2.13.6
OBJECT IDENTIFIER    

ibmappnCosModeTable 1.3.6.1.4.1.2.6.2.13.6.1
Table representing all of the defined mode names for this node. The table contains the matching COS name.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnCosModeEntry

ibmappnCosModeEntry 1.3.6.1.4.1.2.6.2.13.6.1.1
This table is indexed by the Mode Name.
OBJECT-TYPE    
  IbmappnCosModeEntry  

ibmappnCosModeName 1.3.6.1.4.1.2.6.2.13.6.1.1.1
Administratively-assigned name for this mode entry.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnCosModeCosName 1.3.6.1.4.1.2.6.2.13.6.1.1.2
An administratively assigned name for this Class of Service.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnCosNameTable 1.3.6.1.4.1.2.6.2.13.6.2
Table representing all of the defined class-of-service names for this node. The COS node and TG tables are accessed using the same index, which is the COS name.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnCosNameEntry

ibmappnCosNameEntry 1.3.6.1.4.1.2.6.2.13.6.2.1
The COS name is the index to this table.
OBJECT-TYPE    
  IbmappnCosNameEntry  

ibmappnCosName 1.3.6.1.4.1.2.6.2.13.6.2.1.1
Administratively-assigned name for this class of service.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnCosTransPriority 1.3.6.1.4.1.2.6.2.13.6.2.1.2
Transmission priority for this class of service. Values are: Low Medium High Network
OBJECT-TYPE    
  INTEGER low(1), medium(2), high(3), network(4)  

ibmappnCosNodeRowTable 1.3.6.1.4.1.2.6.2.13.6.3
This table contains all node-row information for all class of service in this node.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnCosNodeRowEntry

ibmappnCosNodeRowEntry 1.3.6.1.4.1.2.6.2.13.6.3.1
The COS name is the first index and a integer is the second index to insure a unique index.
OBJECT-TYPE    
  IbmappnCosNodeRowEntry  

ibmappnCosNodeRowName 1.3.6.1.4.1.2.6.2.13.6.3.1.1
Administratively-assigned name for this class of service.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnCosNodeRowIndex 1.3.6.1.4.1.2.6.2.13.6.3.1.2
Index of COS name. This same value is used to access the node and TG COS tables. Range of values is 0-255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnCosNodeRowWgt 1.3.6.1.4.1.2.6.2.13.6.3.1.3
Weight to be associated with the nodes that fit the criteria specified by this node row.
OBJECT-TYPE    
  DisplayString  

ibmappnCosNodeRowResistMin 1.3.6.1.4.1.2.6.2.13.6.3.1.4
Minimum route addition resistance value for this node. Range of values is 0-255. The lower the value, the more desirable the node is for intermediate routing.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnCosNodeRowResistMax 1.3.6.1.4.1.2.6.2.13.6.3.1.5
Maximum route addition resistance value for this node. Range of values is 0-255. The lower the value, the more desirable the node is for intermediate routing.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnCosNodeRowMinCongestAllow 1.3.6.1.4.1.2.6.2.13.6.3.1.6
Indicates whether low congestion will be tolerated. The minimum and maximum parameters will allow specifying either low-congested, high-congested, or either to be used.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnCosNodeRowMaxCongestAllow 1.3.6.1.4.1.2.6.2.13.6.3.1.7
Indicates whether high congestion will be tolerated. The minimum and maximum parameters will allow specifying either low-congested, high-congested, or either to be used.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappnCosTgRowTable 1.3.6.1.4.1.2.6.2.13.6.4
Table containing all the Tg-row information for all class of service defined in this node.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnCosTgRowEntry

ibmappnCosTgRowEntry 1.3.6.1.4.1.2.6.2.13.6.4.1
The TgRowName and the TgRowIndex are the index for this table.
OBJECT-TYPE    
  IbmappnCosTgRowEntry  

ibmappnCosTgRowName 1.3.6.1.4.1.2.6.2.13.6.4.1.1
Administratively-assigned name for this class of service.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnCosTgRowIndex 1.3.6.1.4.1.2.6.2.13.6.4.1.2
Index of COS name. This same value is used to access the node and TG COS tables.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnCosTgRowWgt 1.3.6.1.4.1.2.6.2.13.6.4.1.3
Weight to be associated with the nodes that fit the criteria specified by this tg-row.
OBJECT-TYPE    
  DisplayString  

ibmappnCosTgRowEffCapMin 1.3.6.1.4.1.2.6.2.13.6.4.1.4
Minimum acceptable speed for this Class of Service. The effective capacity is an integer value that indicates the actual kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776.
OBJECT-TYPE    
  INTEGER  

ibmappnCosTgRowEffCapMax 1.3.6.1.4.1.2.6.2.13.6.4.1.5
Maximum acceptable speed for this Class of Service. The effective capacity is an integer value that indicates the actual kilo bits per second. It is derived from the link bandwidth and maximum load factor with the range of 0 thru 603,979,776.
OBJECT-TYPE    
  INTEGER  

ibmappnCosTgRowConnCostMin 1.3.6.1.4.1.2.6.2.13.6.4.1.6
Minimum acceptable cost per connect time for this Class of Service. Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnCosTgRowConnCostMax 1.3.6.1.4.1.2.6.2.13.6.4.1.7
Maximum acceptable cost per connect time for this Class of Service. Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnCosTgRowByteCostMin 1.3.6.1.4.1.2.6.2.13.6.4.1.8
Minimum acceptable cost per byte for this Class of Service.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnCosTgRowByteCostMax 1.3.6.1.4.1.2.6.2.13.6.4.1.9
Maximum acceptable cost per byte for this Class of Service.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnCosTgRowSecurityMin 1.3.6.1.4.1.2.6.2.13.6.4.1.10
Minimum acceptable security for this Class of Service.
OBJECT-TYPE    
  INTEGER nonsecure(1), publicSwitchedNetwork(32), undergroundCable(64), secureConduit(96), guardedConduit(128), encrypted(160), guardedRadiation(192)  

ibmappnCosTgRowSecurityMax 1.3.6.1.4.1.2.6.2.13.6.4.1.11
Maximum acceptable security for this Class of Service.
OBJECT-TYPE    
  INTEGER nonsecure(1), publicSwitchedNetwork(32), undergroundCable(64), secureConduit(96), guardedConduit(128), encrypted(160), guardedRadiation(192)  

ibmappnCosTgRowDelayMin 1.3.6.1.4.1.2.6.2.13.6.4.1.12
Minimum acceptable propagation delay for this class of service. Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with the more values enumerated.
OBJECT-TYPE    
  INTEGER minimum(0), negligible(384), terrestrial(9216), packet(147456), long(294912), maximum(2013265920)  

ibmappnCosTgRowDelayMax 1.3.6.1.4.1.2.6.2.13.6.4.1.13
Maximum acceptable propagation delay for this class of service. Relative amount of time that it takes for a signal to travel the length of the logical link. This time is represented in micro seconds, with the more values enumerated.
OBJECT-TYPE    
  INTEGER minimum(0), negligible(384), terrestrial(9216), packet(147456), long(294912), maximum(2013265920)  

ibmappnCosTgRowUsr1Min 1.3.6.1.4.1.2.6.2.13.6.4.1.14
Minimum acceptable value for this user defined characteristic. Range of values is 0-255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnCosTgRowUsr1Max 1.3.6.1.4.1.2.6.2.13.6.4.1.15
Maximum acceptable value for this user defined characteristic. Range of values is 0-255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnCosTgRowUsr2Min 1.3.6.1.4.1.2.6.2.13.6.4.1.16
Minimum acceptable value for this user defined characteristic. Range of values is 0-255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnCosTgRowUsr2Max 1.3.6.1.4.1.2.6.2.13.6.4.1.17
A Maximum acceptable value for this user defined characteristic.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnCosTgRowUsr3Min 1.3.6.1.4.1.2.6.2.13.6.4.1.18
Minimum acceptable value for this user defined characteristic. Range of values is 0-255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnCosTgRowUsr3Max 1.3.6.1.4.1.2.6.2.13.6.4.1.19
Maximum acceptable value for this user defined characteristic. Range of values is 0-255.
OBJECT-TYPE    
  INTEGER 0..255  

ibmappnSession 1.3.6.1.4.1.2.6.2.13.7
OBJECT IDENTIFIER    

ibmappnSessGeneral 1.3.6.1.4.1.2.6.2.13.7.1
OBJECT IDENTIFIER    

ibmappnSessEndPoint 1.3.6.1.4.1.2.6.2.13.7.2
OBJECT IDENTIFIER    

ibmappcInformation 1.3.6.1.4.1.2.6.2.13.7.2.1
OBJECT IDENTIFIER    

ibmappcInGlobal 1.3.6.1.4.1.2.6.2.13.7.2.1.1
OBJECT IDENTIFIER    

ibmappcInGlobeStatus 1.3.6.1.4.1.2.6.2.13.7.2.1.1.1
Indicates the current collection options in effect: 1. notActive: collection of counters and some names is not active. 2. active: collection of counters and some names is active.
OBJECT-TYPE    
  INTEGER notActive(1), active(2)  

ibmappcInGlobeRscv 1.3.6.1.4.1.2.6.2.13.7.2.1.1.2
Indicates the current collection options in effect: 1. notActive: collection of route selection control vectors is not active. 2. active: collection of route selection control vectors is active.
OBJECT-TYPE    
  INTEGER notActive(1), active(2)  

ibmappcInGlobeRscvTime 1.3.6.1.4.1.2.6.2.13.7.2.1.1.3
Time when the ibmappcInGlobeRscv object last changed. This time is in hundreds of a second.
OBJECT-TYPE    
  TimeTicks  

ibmappcInGlobeCtrStatus 1.3.6.1.4.1.2.6.2.13.7.2.1.1.4
Indicates whether or not the appc session counters are active. This object reflects the combination of the ibmappcInGlobeStatus object and any other product dependant object(s). The values are: 1. notActive: collection of counters and some names is not active. 2. active: collection of counters and some names is active.
OBJECT-TYPE    
  INTEGER notActive(1), active(2)  

ibmappcInGlobeCtrStatusTime 1.3.6.1.4.1.2.6.2.13.7.2.1.1.5
Time when the ibmappcInGlobeCtrStatus object last changed. This time is in hundreds of a second.
OBJECT-TYPE    
  TimeTicks  

ibmappcInGlobeActSess 1.3.6.1.4.1.2.6.2.13.7.2.1.1.6
Number of currently active APPC sessions
OBJECT-TYPE    
  Gauge  

ibmappcInLluTable 1.3.6.1.4.1.2.6.2.13.7.2.1.2
APPC Local Lu Table
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappcInLluEntry

ibmappcInLluEntry 1.3.6.1.4.1.2.6.2.13.7.2.1.2.1
Entry of APPC Local Lu Information Table.
OBJECT-TYPE    
  IbmappcInLluEntry  

ibmappcInLluLuName 1.3.6.1.4.1.2.6.2.13.7.2.1.2.1.1
The network-qualified LU name. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappcInLluDefType 1.3.6.1.4.1.2.6.2.13.7.2.1.2.1.2
Indicates whether the LU definition was specified in the nodes system definitions or was dynamically created.
OBJECT-TYPE    
  INTEGER sysdef(1), dynamic(2)  

ibmappcInLluSessLimit 1.3.6.1.4.1.2.6.2.13.7.2.1.2.1.3
The maximum number of session supported by this LU.
OBJECT-TYPE    
  INTEGER  

ibmappcInLluBindRspMayQ 1.3.6.1.4.1.2.6.2.13.7.2.1.2.1.4
Indicates whether or not a received bind response will be queued if the LU is not currently active.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInLluDefaultLu 1.3.6.1.4.1.2.6.2.13.7.2.1.2.1.5
Indicates whether the LU is the default LU for the node.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInLluCntlPtLu 1.3.6.1.4.1.2.6.2.13.7.2.1.2.1.6
Indicates whether or not the LU is the control point (CP) LU.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInLluCurActSess 1.3.6.1.4.1.2.6.2.13.7.2.1.2.1.7
The number of currently active sessions.
OBJECT-TYPE    
  Gauge  

ibmappcInRluTable 1.3.6.1.4.1.2.6.2.13.7.2.1.3
APPC Remote Partner Lu Table
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappcInRluEntry

ibmappcInRluEntry 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1
Entry of APPC Remote Partner Lu Information Table.
OBJECT-TYPE    
  IbmappcInRluEntry  

ibmappcInRluLocLuName 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.1
The network-qualified local LU name. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappcInRluParLuName 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.2
The network-qualified partner LU name. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappcInRluParLuLocName 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.3
The network-qualified partner LU local name. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappcInRluDefType 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.4
Indicates whether the LU definition was specified in the nodes system definitions or was dynamically created.
OBJECT-TYPE    
  INTEGER sysdef(1), dynamic(2)  

ibmappcInRluDefParaSessSup 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.5
Defined Parallel Sessions Supported. Indicates whether or not multiple session between the partner LU and its associated local LU are permitted.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInRluDefCnosSup 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.6
Defined CNOS Supported. Indicates whether or not Change Number of Sessions (CNOS) will be used to negotiate session limits between the logical points.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInRluDefAllVerSup 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.7
Defined Already Verified Accepted. Indicates whether or not an attach, specifying that TP security has already been verified, is accepted by the adjacent CP LU.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInRluDefAttSecSup 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.8
Defined Attach Security Supported. Indicates whether or not the adjacent CP LU supports attach security.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInRluDefSessSecSup 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.9
Defined Session Security Supported. Indicates whether or not the adjacent CP LU may omit a password in the user data portion of the BIND.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInRluDefEnhanSecSup 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.10
Defined Enhance Security Supported. Indicates the level of enhance security support: 1 = none 2 = level 1 3 = level 2
OBJECT-TYPE    
  INTEGER none(1), level1(2), level2(3)  

ibmappcInRluActType 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.11
Indicates whether the LU active definitions are currently active or not currently active.
OBJECT-TYPE    
  INTEGER active(1), notActive(2)  

ibmappcInRluActParaSessSup 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.12
Active Parallel Sessions Supported. Indicates whether or not multiple session between the partner LU and its associated local LU are permitted.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInRluActCnosSup 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.13
Active CNOS Supported. Indicates whether or not Change Number of Sessions (CNOS) will be used to negotiate session limits between the logical points.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInRluActAllVerSup 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.14
Active Already Verified Accepted. Indicates whether or not an attach, specifying that TP security has already been verified, is accepted by the adjacent CP LU.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInRluActAttSecSup 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.15
Active Attach Security Supported. Indicates whether or not the adjacent CP LU supports attach security.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInRluActSessSecSup 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.16
Active Session Security Supported. Indicates whether or not the adjacent CP LU may omit a password in the user data portion of the BIND.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInRluActEnhanSecSup 1.3.6.1.4.1.2.6.2.13.7.2.1.3.1.17
Active Enhance Security Supported. Indicates the level of enhance security support: 1 = none 2 = level 1 3 = level 2
OBJECT-TYPE    
  INTEGER none(1), level1(2), level2(3)  

ibmappcInMdTable 1.3.6.1.4.1.2.6.2.13.7.2.1.4
APPC Mode Table
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappcInMdEntry

ibmappcInMdEntry 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1
Entry of APPC Mode Information Table.
OBJECT-TYPE    
  IbmappcInMdEntry  

ibmappcInMdLluName 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.1
The network-qualified local LU name. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappcInMdRluName 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.2
The network-qualified remote LU name. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappcInMdModeName 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.3
The mode name.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappcInMdDefType 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.4
Indicates whether the mode definition was specified in the nodes system definitions or was dynamically created.
OBJECT-TYPE    
  INTEGER sysdef(1), dynamic(2)  

ibmappcInMdSessEndTpName 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.5
The session end point transaction program name.
OBJECT-TYPE    
  DisplayString SIZE(1..64)  

ibmappcInMdSessLimit 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.6
Session Limit. Identifies the total number of sessions that can be established with the partner LU.
OBJECT-TYPE    
  INTEGER  

ibmappcInMdMaxSessLimit 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.7
Maximum Session Limit. Specifies the maximum number of sessions supported by the LU pair using this mode name.
OBJECT-TYPE    
  INTEGER  

ibmappcInMdAutoActLimit 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.8
Auto Activate Limit. Specifies the maximum number of sessions which can be activated when this mode is active.
OBJECT-TYPE    
  INTEGER  

ibmappcInMdDrainSelf 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.9
Drain Self. Indicates whether or not the local LU can be drained.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInMdDrainPart 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.10
Drain Partner. Indicates whether or not the partner LU can be drained.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInMdMinCwinLimit 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.11
Minimum Conwinners Limit. Identifies the minimum number of conwinner sessions.
OBJECT-TYPE    
  INTEGER  

ibmappcInMdMinClosLimit 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.12
Minimum Conlossers Limit. Identifies the minimum number of conloser sessions.
OBJECT-TYPE    
  INTEGER  

ibmappcInMdRecvPacWinSz 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.13
The size of the receive pacing window.
OBJECT-TYPE    
  INTEGER  

ibmappcInMdSendPacWinSz 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.14
The size of the send pacing window.
OBJECT-TYPE    
  INTEGER  

ibmappcInMdPrefRecvRuSz 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.15
The preferred receive ru size.
OBJECT-TYPE    
  INTEGER  

ibmappcInMdPrefSendRuSz 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.16
The preferred send ru size.
OBJECT-TYPE    
  INTEGER  

ibmappcInMdRecvRuSzUpBnd 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.17
The receive ru upper boundary size.
OBJECT-TYPE    
  INTEGER  

ibmappcInMdSendRuSzUpBnd 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.18
The send ru upper boundary size.
OBJECT-TYPE    
  INTEGER  

ibmappcInMdRecvRuSzLoBnd 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.19
The receive ru lower boundary size.
OBJECT-TYPE    
  INTEGER  

ibmappcInMdSendRuSzLoBnd 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.20
The send ru lower boundary size.
OBJECT-TYPE    
  INTEGER  

ibmappcInMdDfSyncLvl 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.21
The defined sync level.
OBJECT-TYPE    
  INTEGER none(1), confirm(2), syncPoint(3)  

ibmappcInMdAcSyncLvl 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.22
The active sync level.
OBJECT-TYPE    
  INTEGER none(1), confirm(2), syncPoint(3)  

ibmappcInMdDfCrypto 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.23
Defined cryoptograhy supported.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInMdAcCrypto 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.24
Active cryptography supported.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInMdReinit 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.25
The reinitialization parameter.
OBJECT-TYPE    
  INTEGER operatorControlled(1), primaryOnly(2), secondaryOnly(3), primaryOrSecondary(4)  

ibmappcInMdAltCode 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.26
Alternate code supported.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInMdActCwin 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.27
The number of active conwinners.
OBJECT-TYPE    
  Gauge  

ibmappcInMdActClos 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.28
The number of active conlosers.
OBJECT-TYPE    
  Gauge  

ibmappcInMdPndCwin 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.29
The number of pending conwinners.
OBJECT-TYPE    
  Gauge  

ibmappcInMdPndClos 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.30
The number of pending conlosers.
OBJECT-TYPE    
  Gauge  

ibmappcInMdPtmCwin 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.31
The number of pending termination conlosers.
OBJECT-TYPE    
  Gauge  

ibmappcInMdPtmClos 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.32
The number of pending termination conwinners.
OBJECT-TYPE    
  Gauge  

ibmappcInMdFreeSessLst 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.33
The size of the free seesion list.
OBJECT-TYPE    
  Gauge  

ibmappcInMdWaitReqLst 1.3.6.1.4.1.2.6.2.13.7.2.1.4.1.34
The size of the waiting request list.
OBJECT-TYPE    
  Gauge  

ibmappcInLtpTable 1.3.6.1.4.1.2.6.2.13.7.2.1.5
APPC Local TP Table
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappcInLtpEntry

ibmappcInLtpEntry 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1
Entry of APPC Local TP Information Table.
OBJECT-TYPE    
  IbmappcInLtpEntry  

ibmappcInLtpLuName 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.1
The network-qualified local LU name. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappcInLtpTpName 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.2
The local transaction program name.
OBJECT-TYPE    
  DisplayString SIZE(1..64)  

ibmappcInLtpDefType 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.3
The TP definition type. Indicates whether the TP was specified in the nodes system definitions or was dynamically created.
OBJECT-TYPE    
  INTEGER sysdef(1), dynamic(2)  

ibmappcInLtpSyncLvl 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.4
The TP synchroniztion level.
OBJECT-TYPE    
  INTEGER none(1), confirm(2), syncPoint(3)  

ibmappcInLtpInstLmt 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.5
The TP instance limit.
OBJECT-TYPE    
  INTEGER  

ibmappcInLtpInstNum 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.6
The number of TP instances.
OBJECT-TYPE    
  Gauge  

ibmappcInLtpStatus 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.7
The TP status.
OBJECT-TYPE    
  INTEGER enabled(1), tempDisabled(2), permDisabled(3)  

ibmappcInLtpLongRun 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.8
The long running transaction program.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInLtpPfCnos 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.9
The TP Change Number of Sessions (CNOS) privileged function. This parameter specifies whether or not this program is allowed to issue CNOS verbs.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInLtpPfSessCntl 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.10
The TP Session Control privileged function. This parameter specifies whether or not this program is allowed to issue ACTIVATE_SESSION and DEACTIVATE_SESSION verbs.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInLtpPfDefine 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.11
The TP Define privileged function. This parameter specifies whether or not this program is allowed to issue DEFINE and DELETE verbs.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInLtpPfDisplay 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.12
The TP Display privileged function. This parameter specifies whether or not this program is allowed to issue DISPLAY verbs.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInLtpPfAllocSer 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.13
The TP Allocate Service privileged function. This parameter specifies whether or not this program is allowed to issue the ALLOCATE verb with its TPN parameter specifying an SNA service transmission program.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInLtpRescSup 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.14
The TP resources supported parameter. 1. basic conversations 2. mapped conversations 3. all conversations
OBJECT-TYPE    
  INTEGER basicConv(1), mappedConv(2), allConv(3)  

ibmappcInLtpRecoSup 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.15
The TP reconnect supported parameter.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInLtpSecReq 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.16
The TP security required parameter.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInLtpSecLvl 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.17
The TP security level parameter.
OBJECT-TYPE    
  INTEGER noAdditional(1), specificUsers(2), specificProfiles(3), specificUserProfiles(4), specificUserLus(5), specificUserProfLus(6)  

ibmappcInLtpVerPip 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.18
The TP verify pip parameter.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ibmappcInLtpPipSubNum 1.3.6.1.4.1.2.6.2.13.7.2.1.5.1.19
The TP number of pip subfields.
OBJECT-TYPE    
  INTEGER  

ibmappcInSsTable 1.3.6.1.4.1.2.6.2.13.7.2.1.6
APPC Session Table
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappcInSsEntry

ibmappcInSsEntry 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1
Entry of APPC Session Information Table.
OBJECT-TYPE    
  IbmappcInSsEntry  

ibmappcInSsFqLuName 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.1
The network-qualified CP name or PU name of the node at which the session and cid originated. For APPN and LEN nodes, this is either CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappcInSsPcid 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.2
The procedure correlation identifier (pcid) of a session. It is an 8-octet value assigned by the primary LU.
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

ibmappcInSsPluName 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.3
The primary LU name of the session.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappcInSsSluName 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.4
The secondary LU name of the session.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappcInSsModeName 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.5
The Mode Name name used for this session. This is a 1-8 character name.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappcInSsCosName 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.6
The Class of Service (COS) name used for this session. This is a 1-8 character name.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappcInSsSessType 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.7
The type of session.
OBJECT-TYPE    
  INTEGER lu62(1)  

ibmappcInSsSessState 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.8
Indicates the state of the session. 1. session is pending inactive or, 2. session is pending active or, 3. session is active or, 4. session is inactive
OBJECT-TYPE    
  INTEGER inactive(1), pendactive(2), active(3), pendinact(4)  

ibmappcInSsTransPriority 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.9
The transmission priority of this session.
OBJECT-TYPE    
  INTEGER  

ibmappcInSsPaceType 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.10
The type of pacing used for this session.
OBJECT-TYPE    
  INTEGER none(1), fixed(2), adaptive(3)  

ibmappcInSsSendMaxRuSz 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.11
The maximum ru size which can be sent.
OBJECT-TYPE    
  INTEGER  

ibmappcInSsRecvMaxRuSz 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.12
The maximum ru size which can be received.
OBJECT-TYPE    
  INTEGER  

ibmappcInSsEnhanceSecSup 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.13
Enhanced security supported. Indicates the level of enhance security support: 1 = none 2 = level 1 3 = level 2
OBJECT-TYPE    
  INTEGER none(1), level1(2), level2(3)  

ibmappcInSsSendPacingType 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.14
The type of pacing being used for sending data.
OBJECT-TYPE    
  INTEGER none(1), fixed(2), adaptive(3)  

ibmappcInSsSendRpc 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.15
The send residual pace count. This represents the number of MU's that can still be sent in the current session window.
OBJECT-TYPE    
  Gauge  

ibmappcInSsSendNxWndwSize 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.16
The size of the next window which will be used to send data.
OBJECT-TYPE    
  Gauge  

ibmappcInSsRecvPacingType 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.17
The type of pacing being used for receiving data.
OBJECT-TYPE    
  INTEGER none(1), fixed(2), adaptive(3)  

ibmappcInSsRecvRpc 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.18
The receive residual pace count. This represents the number of MU's that can still be received in the current session window.
OBJECT-TYPE    
  Gauge  

ibmappcInSsRecvNxWndwSize 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.19
The size of the next window which will be used to receive data.
OBJECT-TYPE    
  Gauge  

ibmappcInSsSessStartTime 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.20
Time when the session started in hundreds of a second.
OBJECT-TYPE    
  TimeTicks  

ibmappcInSsSessUpTime 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.21
Length of time the session has been active in hundreds of a second.
OBJECT-TYPE    
  TimeTicks  

ibmappcInSsCtrUpTime 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.22
Length of time the session counters have been active in hundreds of a second.
OBJECT-TYPE    
  TimeTicks  

ibmappcInSsP2SFmdPius 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.23
Number of FMD PIUs sent from the Primary LU to the Secondary LU
OBJECT-TYPE    
  Counter  

ibmappcInSsS2PFmdPius 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.24
Number of FMD PIUs sent from the Secondary LU to the Primary LU
OBJECT-TYPE    
  Counter  

ibmappcInSsP2SNonFmdPius 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.25
Number of non-FMD PIUs sent from the Primary LU to the Secondary LU
OBJECT-TYPE    
  Counter  

ibmappcInSsS2PNonFmdPius 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.26
Number of non-FMD PIUs sent from the Secondary LU to the Primary LU
OBJECT-TYPE    
  Counter  

ibmappcInSsP2SFmdBytes 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.27
Number of FMD Bytes sent from the Primary LU to the Secondary LU
OBJECT-TYPE    
  Counter  

ibmappcInSsS2PFmdBytes 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.28
Number of FMD Bytes sent from the Secondary LU to the Primary LU
OBJECT-TYPE    
  Counter  

ibmappcInSsP2SNonFmdBytes 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.29
Number of non-FMD Bytes sent from the Primary LU to the Secondary LU
OBJECT-TYPE    
  Counter  

ibmappcInSsS2PNonFmdBytes 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.30
Number of non-FMD Bytes sent from the Secondary LU to the Primary LU
OBJECT-TYPE    
  Counter  

ibmappcInSsRscv 1.3.6.1.4.1.2.6.2.13.7.2.1.6.1.31
The route selection control vector (RSCV x'2B') used for this session. It is not present for APPN CP-CP sessions and also not present for LEN nodes. The format of this vector is described in SNA Formats.
OBJECT-TYPE    
  OCTET STRING  

ibmappcInSsStatusTable 1.3.6.1.4.1.2.6.2.13.7.2.1.7
APPC Session Status Table
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappcInSsStatusEntry

ibmappcInSsStatusEntry 1.3.6.1.4.1.2.6.2.13.7.2.1.7.1
Entry of APPC Session Status Information Table. This table is indexed by the SsStatusIndex, which is an integer that is continuously updated until it eventually wraps. This provides the management station the ability to retrieve only the updates to the table by using the standard GET NEXT.
OBJECT-TYPE    
  IbmappcInSsStatusEntry  

ibmappcInSsStatusIndex 1.3.6.1.4.1.2.6.2.13.7.2.1.7.1.1
Table index. The value of the index begins at zero and is incremented up to a maximum value of 2**31-1 (2,147,483,647) before wrapping.
OBJECT-TYPE    
  INTEGER  

ibmappcInSsStatusTime 1.3.6.1.4.1.2.6.2.13.7.2.1.7.1.2
Time (in hundreds of a second) since this node was last initialized.
OBJECT-TYPE    
  TimeTicks  

ibmappcInSsStatusType 1.3.6.1.4.1.2.6.2.13.7.2.1.7.1.3
Indicates the entry type: 1. Received a negative bind response from the partner LU. 2. Sent a negative bind response to the partner LU. 3. Session activation rejected by the partner LU. 4. Unbind sent to the partner LU. 5. Unbind received from the partner LU.
OBJECT-TYPE    
  INTEGER recvNegBindRsp(1), sendNegBindRsp(2), sessActRejected(3), unbindSent(4), unbindReceived(5)  

ibmappcInSsStatusLocLuName 1.3.6.1.4.1.2.6.2.13.7.2.1.7.1.4
The network-qualified local LU name. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappcInSsStatusParLuName 1.3.6.1.4.1.2.6.2.13.7.2.1.7.1.5
The network-qualified partner LU name. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappcInSsStatusModeName 1.3.6.1.4.1.2.6.2.13.7.2.1.7.1.6
The mode name.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappcInSsStatusUnbindType 1.3.6.1.4.1.2.6.2.13.7.2.1.7.1.7
The type of unbind which terminated the session. This value is consists of one (1) octet; and its meaning is defined in SNA Formats.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ibmappcInSsStatusSenseCode 1.3.6.1.4.1.2.6.2.13.7.2.1.7.1.8
The sense code associated with the termination of the session. This value consists of four (4) octets; and its meaning is defined in SNA Formats.
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

ibmappcInSsStatusComponentId 1.3.6.1.4.1.2.6.2.13.7.2.1.7.1.9
The name of the component which sent the entry.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappcInSsStatusDetectModule 1.3.6.1.4.1.2.6.2.13.7.2.1.7.1.10
The name of the module which detected the condition and sent the entry.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnSessIntermediate 1.3.6.1.4.1.2.6.2.13.7.3
OBJECT IDENTIFIER    

ibmappnIsInformation 1.3.6.1.4.1.2.6.2.13.7.3.1
OBJECT IDENTIFIER    

ibmappnIsInGlobal 1.3.6.1.4.1.2.6.2.13.7.3.1.1
OBJECT IDENTIFIER    

ibmappnIsInGlobeStatus 1.3.6.1.4.1.2.6.2.13.7.3.1.1.1
Indicates the current collection options in effect: 1. notActive: collection of counters and some names is not active. 2. active: collection of counters and some names is active.
OBJECT-TYPE    
  INTEGER notActive(1), active(2)  

ibmappnIsInGlobeRscv 1.3.6.1.4.1.2.6.2.13.7.3.1.1.2
Indicates the current collection options in effect: 1. notActive: collection of route selection control vectors is not active. 2. active: collection of route selection control vectors is active.
OBJECT-TYPE    
  INTEGER notActive(1), active(2)  

ibmappnIsInGlobeRscvTime 1.3.6.1.4.1.2.6.2.13.7.3.1.1.3
Time when the ibmappnIsInGlobeRscv object last changed. This time is in hundreds of a second.
OBJECT-TYPE    
  TimeTicks  

ibmappnIsInGlobeCtrStatus 1.3.6.1.4.1.2.6.2.13.7.3.1.1.4
Indicates whether or not the intermediate session counters are active. This object reflects the combination of the ibmappnIsInGlobeStatus object and the ibmappnIsAcBtypeActive object. The values are: 1. notActive: collection of counters and some names is not active. 2. active: collection of counters and some names is active.
OBJECT-TYPE    
  INTEGER notActive(1), active(2)  

ibmappnIsInGlobeCtrStatusTime 1.3.6.1.4.1.2.6.2.13.7.3.1.1.5
Time when the ibmappnIsInGlobeCtrStatus object last changed. This time is in hundreds of a second.
OBJECT-TYPE    
  TimeTicks  

ibmappnIsInTable 1.3.6.1.4.1.2.6.2.13.7.3.1.2
Intermediate Session Information Table
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnIsInEntry

ibmappnIsInEntry 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1
Entry of Intermediate Session Information Table.
OBJECT-TYPE    
  IbmappnIsInEntry  

ibmappnIsInFqLuName 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.1
The network-qualified CP name or PU name of the node at which the session and cid originated. For APPN and LEN nodes, this is either CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnIsInPcid 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.2
The procedure correlation identifier (pcid) of a session. It is an 8-octet value assigned by the primary LU.
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

ibmappnIsInPriLuName 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.3
The primary LU name of the session.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnIsInSecLuName 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.4
The secondary LU name of the session.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnIsInModeName 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.5
The Mode Name name used for this session. This is a 1-8 character name.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnIsInCosName 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.6
The Class of Service (COS) name used for this session. This is a 1-8 character name.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnIsInTransPriority 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.7
The transmission priority of this session.
OBJECT-TYPE    
  INTEGER  

ibmappnIsInSessType 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.8
The type of intermediate session.
OBJECT-TYPE    
  INTEGER lu62(1), lu0thru3(2)  

ibmappnIsInSessState 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.9
Indicates the state of the session. 1. session is pending inactive or, 2. session is pending active or, 3. session is active or, 4. session is inactive Existing sessions can be deactivated by setting this object to inactive.
OBJECT-TYPE    
  INTEGER inactive(1), pendactive(2), active(3), pendinact(4)  

ibmappnIsInSessStartTime 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.10
Time when the session started in hundreds of a second.
OBJECT-TYPE    
  TimeTicks  

ibmappnIsInSessUpTime 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.11
Length of time the session has been active in hundreds of a second.
OBJECT-TYPE    
  TimeTicks  

ibmappnIsInCtrUpTime 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.12
Length of time the session counters have been active in hundreds of a second.
OBJECT-TYPE    
  TimeTicks  

ibmappnIsInP2SFmdPius 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.13
Number of FMD PIUs sent from the Primary LU to the Secondary LU
OBJECT-TYPE    
  Counter  

ibmappnIsInS2PFmdPius 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.14
Number of FMD PIUs sent from the Secondary LU to the Primary LU
OBJECT-TYPE    
  Counter  

ibmappnIsInP2SNonFmdPius 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.15
Number of non-FMD PIUs sent from the Primary LU to the Secondary LU
OBJECT-TYPE    
  Counter  

ibmappnIsInS2PNonFmdPius 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.16
Number of non-FMD PIUs sent from the Secondary LU to the Primary LU
OBJECT-TYPE    
  Counter  

ibmappnIsInP2SFmdBytes 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.17
Number of FMD Bytes sent from the Primary LU to the Secondary LU
OBJECT-TYPE    
  Counter  

ibmappnIsInS2PFmdBytes 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.18
Number of FMD Bytes sent from the Secondary LU to the Primary LU
OBJECT-TYPE    
  Counter  

ibmappnIsInP2SNonFmdBytes 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.19
Number of non-FMD Bytes sent from the Primary LU to the Secondary LU
OBJECT-TYPE    
  Counter  

ibmappnIsInS2PNonFmdBytes 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.20
Number of non-FMD Bytes sent from the Secondary LU to the Primary LU
OBJECT-TYPE    
  Counter  

ibmappnIsInPsAdjCpName 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.21
The primary stage adjacent CP name of this session.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnIsInPsAdjTgNum 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.22
The primary stage adjacent transmission group (TG) number associated with this session.
OBJECT-TYPE    
  INTEGER  

ibmappnIsInPsSendMaxBtuSize 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.23
The primary stage maximum basic transmission size (BTU) for sending data.
OBJECT-TYPE    
  INTEGER  

ibmappnIsInPsSendPacingType 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.24
The primary stage type of pacing being used for sending data.
OBJECT-TYPE    
  INTEGER fixed(1), adaptive(2)  

ibmappnIsInPsSendRpc 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.25
The primary stage send residual pace count. This represents the primary stage number of MU's that can still be sent in the current session window.
OBJECT-TYPE    
  Gauge  

ibmappnIsInPsSendNxWndwSize 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.26
The primary stage size of the next window which will be used to send data.
OBJECT-TYPE    
  Gauge  

ibmappnIsInPsRecvPacingType 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.27
The primary stage type of pacing being used for receiving data.
OBJECT-TYPE    
  INTEGER fixed(1), adaptive(2)  

ibmappnIsInPsRecvRpc 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.28
The primary stage receive residual pace count. This represents the primary stage number of MU's that can still be received in the current session window.
OBJECT-TYPE    
  Gauge  

ibmappnIsInPsRecvNxWndwSize 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.29
The primary stage size of the next window which will be used to receive data.
OBJECT-TYPE    
  Gauge  

ibmappnIsInSsAdjCpName 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.30
The secondary stage adjacent CP name of this session.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnIsInSsAdjTgNum 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.31
The secondary stage adjacent transmission group (TG) number associated with this session.
OBJECT-TYPE    
  INTEGER  

ibmappnIsInSsSendMaxBtuSize 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.32
The secondary stage maximum basic transmission size (BTU) for sending data.
OBJECT-TYPE    
  INTEGER  

ibmappnIsInSsSendPacingType 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.33
The secondary stage type of pacing being used for sending data.
OBJECT-TYPE    
  INTEGER fixed(1), adaptive(2)  

ibmappnIsInSsSendRpc 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.34
The secondary stage send residual pace count. This represents the secondary stage number of MU's that can still be sent in the current session window.
OBJECT-TYPE    
  Gauge  

ibmappnIsInSsSendNxWndwSize 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.35
The secondary stage size of the next window which will be used to send data.
OBJECT-TYPE    
  Gauge  

ibmappnIsInSsRecvPacingType 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.36
The secondary stage type of pacing being used for receiving data.
OBJECT-TYPE    
  INTEGER fixed(1), adaptive(2)  

ibmappnIsInSsRecvRpc 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.37
The secondary stage send residual pace count. This represents the secondary stage number of MU's that can still be received in the current session window.
OBJECT-TYPE    
  Gauge  

ibmappnIsInSsRecvNxWndwSize 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.38
The secondary stage size of the next window which will be used to receive data.
OBJECT-TYPE    
  Gauge  

ibmappnIsInRouteInfo 1.3.6.1.4.1.2.6.2.13.7.3.1.2.1.39
The route selection control vector (RSCV x'2B') used for this session. It is present for APPN nodes; but is not present for LEN nodes. The format of this vector is described in SNA Formats.
OBJECT-TYPE    
  OCTET STRING  

ibmappnIsAccounting 1.3.6.1.4.1.2.6.2.13.7.3.2
OBJECT IDENTIFIER    

ibmappnIsAcGlobal 1.3.6.1.4.1.2.6.2.13.7.3.2.1
OBJECT IDENTIFIER    

ibmappnIsAcGlobeStatus 1.3.6.1.4.1.2.6.2.13.7.3.2.1.1
This object indicates the current status for accounting type. 1. indicates collection is not active for any media type. 2. indicates collection is active for at least one media type; and that media is not full. 3. indicates collection is active for at least one media type; but all active medias are full.
OBJECT-TYPE    
  INTEGER notActive(1), activeNotFull(2), activeButFull(3)  

ibmappnIsAcGlobeByteThresh 1.3.6.1.4.1.2.6.2.13.7.3.2.1.2
The byte threshold for recording accounting information for an active session. If the total of the byte counters (FmdBytes and NonFmdBtyes) is an even multiple of this non-zero value, statistics for this session will be recorded to all active buffers. A value of zero indicates that no byte threshold has been set.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcGlobeCheckPt 1.3.6.1.4.1.2.6.2.13.7.3.2.1.3
By setting this value to yes, the agent will collect accounting information for all active sessions. This information will be recorded to all active buffers.
OBJECT-TYPE    
  INTEGER ready(1), yes(2)  

ibmappnIsAcGlobeMgrUtcSecs 1.3.6.1.4.1.2.6.2.13.7.3.2.1.4
The managers Coordinated Universal Time (UTC) seconds. It contains an integer from 0 to 59. By setting this value, the agent will create time record with its corresponding time and name. When setting this object, the manager should also set all other ibmappnIsAcGlobeMgr objects with the same SET operation.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcGlobeMgrUtcMins 1.3.6.1.4.1.2.6.2.13.7.3.2.1.5
The managers Coordinated Universal Time (UTC) minutes. It contains an integer from 0 to 59. By setting this value, the agent will create time record with its corresponding time and name. When setting this object, the manager should also set all other ibmappnIsAcGlobeMgr objects with the same SET operation.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcGlobeMgrUtcHours 1.3.6.1.4.1.2.6.2.13.7.3.2.1.6
The managers Coordinated Universal Time (UTC) hours. It contains an integer from 0 to 23. By setting this value, the agent will create time record with its corresponding time and name. When setting this object, the manager should also set all other ibmappnIsAcGlobeMgr objects with the same SET operation.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcGlobeMgrUtcMdays 1.3.6.1.4.1.2.6.2.13.7.3.2.1.7
The managers Coordinated Universal Time (UTC) day of the month. It contains an integer from 1 to 31; or 0 if the manager has not set this object. By setting this value, the agent will create time record with its corresponding time and name. When setting this object, the manager should also set all other ibmappnIsAcGlobeMgr objects with the same SET operation.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcGlobeMgrUtcMonths 1.3.6.1.4.1.2.6.2.13.7.3.2.1.8
The managers Coordinated Universal Time (UTC) months since January. It contains an integer from 0 to 11. By setting this value, the agent will create time record with its corresponding time and name. When setting this object, the manager should also set all other ibmappnIsAcGlobeMgr objects with the same SET operation.
OBJECT-TYPE    
  INTEGER january(0), february(1), march(2), april(3), may(4), june(5), july(6), august(7), september(8), october(9), november(10), december(11)  

ibmappnIsAcGlobeMgrUtcYears 1.3.6.1.4.1.2.6.2.13.7.3.2.1.9
The managers Coordinated Universal Time (UTC) years since 1900. By setting this value, the agent will create time record with its corresponding time and name. When setting this object, the manager should also set all other ibmappnIsAcGlobeMgr objects with the same SET operation.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcGlobeMgrUtcWdays 1.3.6.1.4.1.2.6.2.13.7.3.2.1.10
The managers Coordinated Universal Time (UTC) days since Sunday. It contains an integer from 0 to 6. By setting this value, the agent will create time record with its corresponding time and name. When setting this object, the manager should also set all other ibmappnIsAcGlobeMgr objects with the same SET operation.
OBJECT-TYPE    
  INTEGER sunday(0), monday(1), tuesday(2), wednesday(3), thursday(4), friday(5), saturday(6)  

ibmappnIsAcGlobeMgrUtcYdays 1.3.6.1.4.1.2.6.2.13.7.3.2.1.11
The managers Coordinated Universal Time (UTC) days since January 1. It contains an integer from 0 to 365. By setting this value, the agent will create time record with its corresponding time and name. When setting this object, the manager should also set all other ibmappnIsAcGlobeMgr objects with the same SET operation.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcGlobeMgrUtcIsdst 1.3.6.1.4.1.2.6.2.13.7.3.2.1.12
The managers Coordinated Universal Time (UTC) daylight saving time flag. It is positive if daylight saving time is in effect. It is zero if daylight saving time is not in effect. By setting this value, the agent will create time record with its corresponding time and name. When setting this object, the manager should also set all other ibmappnIsAcGlobeMgr objects with the same SET operation.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcGlobeMgrName 1.3.6.1.4.1.2.6.2.13.7.3.2.1.13
The name of the manager who set the manager UTC times or NULL if the manager name has not been set. It contains: a. the network id of the manager, b. a period (.) c. the cp name of the manager. By setting this value, the agent will create time record with its corresponding time and name. When setting this object, the manager should also set all other ibmappnIsAcGlobeMgr objects with the same SET operation.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnIsAcBtypeTable 1.3.6.1.4.1.2.6.2.13.7.3.2.2
Intermediate Session Accounting Buffer Type Table
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnIsAcBtypeEntry

ibmappnIsAcBtypeEntry 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1
Entry of Intermediate Session Accounting Buffer Type Table.
OBJECT-TYPE    
  IbmappnIsAcBtypeEntry  

ibmappnIsAcBtypeMedia 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.1
The media for storing the intermediate session accounting records.
OBJECT-TYPE    
  INTEGER memory(1), dasd(2)  

ibmappnIsAcBtypeActive 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.2
Indicates whether or not the buffer media is active. 1. no: indicates the buffer media is not currently used for recording. 2. yes: indicates the buffer media is currently being used for recording.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ibmappnIsAcBtypeDirName 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.3
The name of the directory which will be used to allocate and write buffers of this type. For memory buffer types, this field will be NULL.
OBJECT-TYPE    
  DisplayString  

ibmappnIsAcBtypePrdMaxBufs 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.4
The maximum number of buffer medias supported by the product.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBtypeMaxBufs 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.5
The maximum number of buffer medias which will be used for recording accounting information. This value must be in the range of zero to the Product Maximum.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBtypeCurBufs 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.6
The current number of buffer media. This is the sum of all full and in use buffers of this type.
OBJECT-TYPE    
  Gauge  

ibmappnIsAcBtypePrdRecPerBuf 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.7
The maximum number of records supported by the product.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBtypeRecPerBuf 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.8
The maximum number of records which will be recorded in an individual buffer. This value must be in the range of zero to the Product Maximum.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBtypeRecFormat 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.9
This defines the recording format of records. (1) ascii: records are recorded in ascii (english text format) (2) binary: records are recorded in binary (machine readable format)
OBJECT-TYPE    
  INTEGER ascii(1), binary(2)  

ibmappnIsAcBtypeFullAction 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.10
This defines the behaviour used when all buffer medias are full. (1) halt: stop creating new records (2) wrap: overwrite the existing records.
OBJECT-TYPE    
  INTEGER halt(1), wrap(2)  

ibmappnIsAcBtypeFullTime 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.11
The time which the full condition was encountered. This time is represented in hundreds of a second since the node was started. 2**32-1 (4,294,967,295), and wraps.
OBJECT-TYPE    
  TimeTicks  

ibmappnIsAcBtypeFullReason 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.12
The reason the buffer media is full. (1) The media is not full. (2) The maximum number of buffers have been reach, all buffers are full and the full action is halt. (3) The maximum number of buffers is zero or the maximum number of records is less than 5 or a unique record number cannot be generated. (4) Unable to write to the media due to I/O errors.
OBJECT-TYPE    
  INTEGER notFull(1), physicallyFull(2), logicallyFull(3), ioErrors(4)  

ibmappnIsAcBtypeFullWraps 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.13
The number of accounting records being overwritten due to buffer full situation.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBtypeFullLosts 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.14
The number of new accounting records lost due to the buffer full situation.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBtypeErrorWraps 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.15
The number of accounting records lost to due to other reasons, (e.g. I/O error, software error) while in a wrap condition.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBtypeErrorLosts 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.16
The number of accounting records lost to due to other reasons, (e.g. I/O error, software error) while not in a full condition.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBtypeCheckPts 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.17
The number of times a buffer of this type has been recorded to for checkpointing active intermediate sessions.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBtypePurges 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.18
The number of times a buffer of this type has been purged.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBtypeDeletes 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.19
The number of times an entry has been deleted from a buffer of this type.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBtypeResets 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.20
The number of times the Btype counters have been reset as a result of a SET.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBtypeClearStats 1.3.6.1.4.1.2.6.2.13.7.3.2.2.1.21
By setting this object to yes, all statistics for this media type will be cleared (set to zero); and the Btype reset counter will be incremented. Objects affected by this include: - ibmappnIsAcBtypeFullTime - ibmappnIsAcBtypeFullReason - ibmappnIsAcBtypeFullWraps - ibmappnIsAcBtypeFullLosts - ibmappnIsAcBtypeErrorWraps - ibmappnIsAcBtypeErrorLosts - ibmappnIsAcBtypeCheckPts - ibmappnIsAcBtypePurges - ibmappnIsAcBtypeDeletes
OBJECT-TYPE    
  INTEGER ready(1), yes(2)  

ibmappnIsAcBufTable 1.3.6.1.4.1.2.6.2.13.7.3.2.3
Intermediate Session Accounting Buffer Table
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnIsAcBufEntry

ibmappnIsAcBufEntry 1.3.6.1.4.1.2.6.2.13.7.3.2.3.1
Entry of Intermediate Session Accounting Buffer Table.
OBJECT-TYPE    
  IbmappnIsAcBufEntry  

ibmappnIsAcBufMedia 1.3.6.1.4.1.2.6.2.13.7.3.2.3.1.1
The media for storing the intermediate session accounting records.
OBJECT-TYPE    
  INTEGER memory(1), dasd(2)  

ibmappnIsAcBufNumber 1.3.6.1.4.1.2.6.2.13.7.3.2.3.1.2
Number of the buffer. Each time a new buffer is used for recording, an incremented number will be assigned. Thus, the order of in which the buffers filled can be determined.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBufState 1.3.6.1.4.1.2.6.2.13.7.3.2.3.1.3
The current buffer state. 1. complete: indicates the buffer is full or recording is not active for this buffer. In either case, the buffer is ready to be retrieved. This value may be specified in a SET operation to change a buffers state from active to complete. 2. active: indicates the buffer is currently being used for recording. This value is not valid for use in a SET operation. 3. purge: indicates the buffer should be purged. This value may be specified in a SET operation to remove a buffer. Specification of this value is only valid for complete buffers. It is not valid for active buffers.
OBJECT-TYPE    
  INTEGER complete(1), active(2), purge(3)  

ibmappnIsAcBufRecFormat 1.3.6.1.4.1.2.6.2.13.7.3.2.3.1.4
This defines the recording format of records. (1) ascii: records are recorded in ascii (english text format) (2) binary: records are recorded in binary (machine readable format)
OBJECT-TYPE    
  INTEGER ascii(1), binary(2)  

ibmappnIsAcBufMaxRecords 1.3.6.1.4.1.2.6.2.13.7.3.2.3.1.5
The maximum number of records this buffer may contain. It is derived from the number of records per buffer set in the buffer type table.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBufOldestIndex 1.3.6.1.4.1.2.6.2.13.7.3.2.3.1.6
The oldest accounting index contained in this buffer. By setting this object, all records with indexes less than this value will be deleted. The set value must be greater than or equal to the current oldest index and less than or equal to the current newest index. Setting of this object will not be honored for all types of buffers.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBufNewestIndex 1.3.6.1.4.1.2.6.2.13.7.3.2.3.1.7
The newest accounting index contained in this buffer.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcBufName 1.3.6.1.4.1.2.6.2.13.7.3.2.3.1.8
The name of the buffer.
OBJECT-TYPE    
  DisplayString  

ibmappnIsAcTimeTable 1.3.6.1.4.1.2.6.2.13.7.3.2.4
Intermediate Session Accounting Time Table
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnIsAcTimeEntry

ibmappnIsAcTimeEntry 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1
Entry of Intermediate Session Accounting Time Table.
OBJECT-TYPE    
  IbmappnIsAcTimeEntry  

ibmappnIsAcTimeIndex 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.1
Intermediate Session Time record index. It starts with 0, and increase up to maximum value of 2**31-1 (2,147,483,647), and wraps.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcTimeEntryType 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.2
Indicates whether the entry was made as the result of: 1. a SET to start collecting accounting data, or 2. a SET to stop collecting accounting data, or 3. the creation of a new media to store accounting data, or 4. a media was full and wrapped (over writing records), or 5. the system time changed, or 6. a manager set the manager times and/or manager name, or 7. the record format for this media changed, or 8. time reference for the media
OBJECT-TYPE    
  INTEGER startCollection(1), endCollection(2), createdMedia(3), wrappedMedia(4), timeChange(5), managerSetTime(6), recordFormatChanged(7), timeReference(8)  

ibmappnIsAcTimeForMedia 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.3
This object qualifies the time entry type. It indicates the media type for which the entry occured.
OBJECT-TYPE    
  INTEGER memoryMedia(1), dasdMedia(2), allMedias(99)  

ibmappnIsAcTimeRecTime 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.4
Intermediate Session Record time. It represents the time in hundreds of a second since the node was started. 2**32-1 (4,294,967,295), and wraps.
OBJECT-TYPE    
  TimeTicks  

ibmappnIsAcTimeAgtUtcSecs 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.5
The agents Coordinated Universal Time (UTC) seconds. It contains an integer from 0 to 59.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcTimeAgtUtcMins 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.6
The agents Coordinated Universal Time (UTC) minutes. It contains an integer from 0 to 59.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcTimeAgtUtcHours 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.7
The agents Coordinated Universal Time (UTC) hours. It contains an integer from 0 to 23.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcTimeAgtUtcMdays 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.8
The agents Coordinated Universal Time (UTC) day of the month. It contains an integer from 1 to 31.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcTimeAgtUtcMonths 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.9
The agents Coordinated Universal Time (UTC) months since January. It contains an integer from 0 to 11.
OBJECT-TYPE    
  INTEGER january(0), february(1), march(2), april(3), may(4), june(5), july(6), august(7), september(8), october(9), november(10), december(11)  

ibmappnIsAcTimeAgtUtcYears 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.10
The agents Coordinated Universal Time (UTC) years since 1900.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcTimeAgtUtcWdays 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.11
The agents Coordinated Universal Time (UTC) days since Sunday. It contains an integer from 0 to 6.
OBJECT-TYPE    
  INTEGER sunday(0), monday(1), tuesday(2), wednesday(3), thursday(4), friday(5), saturday(6)  

ibmappnIsAcTimeAgtUtcYdays 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.12
The agents Coordinated Universal Time (UTC) days since January 1. It contains an integer from 0 to 365.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcTimeAgtUtcIsdst 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.13
The agents Coordinated Universal Time (UTC) daylight saving time flag. It is positive if daylight saving time is in effect. It is zero if daylight saving time is not in effect.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcTimeAgtName 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.14
The name of the agent who set the agent UTC times. It contains: a. the network id of the agent, b. a period (.) c. the cp name of the agent.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnIsAcTimeMgrUtcSecs 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.15
The managers Coordinated Universal Time (UTC) seconds. It contains an integer from 0 to 59.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcTimeMgrUtcMins 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.16
The managers Coordinated Universal Time (UTC) minutes. It contains an integer from 0 to 59.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcTimeMgrUtcHours 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.17
The managers Coordinated Universal Time (UTC) hours. It contains an integer from 0 to 23.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcTimeMgrUtcMdays 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.18
The managers Coordinated Universal Time (UTC) day of the month. It contains an integer from 1 to 31; or 0 if the manager has not set this object.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcTimeMgrUtcMonths 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.19
The managers Coordinated Universal Time (UTC) months since January. It contains an integer from 0 to 11.
OBJECT-TYPE    
  INTEGER january(0), february(1), march(2), april(3), may(4), june(5), july(6), august(7), september(8), october(9), november(10), december(11)  

ibmappnIsAcTimeMgrUtcYears 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.20
The managers Coordinated Universal Time (UTC) years since 1900.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcTimeMgrUtcWdays 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.21
The managers Coordinated Universal Time (UTC) days since Sunday. It contains an integer from 0 to 6.
OBJECT-TYPE    
  INTEGER sunday(0), monday(1), tuesday(2), wednesday(3), thursday(4), friday(5), saturday(6)  

ibmappnIsAcTimeMgrUtcYdays 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.22
The managers Coordinated Universal Time (UTC) days since January 1. It contains an integer from 0 to 365.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcTimeMgrUtcIsdst 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.23
The managers Coordinated Universal Time (UTC) daylight saving time flag. It is positive if daylight saving time is in effect. It is zero if daylight saving time is not in effect.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcTimeMgrName 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.24
The name of the manager who set the manager UTC times or NULL if the manager name has not been set. It contains: a. the network id of the manager, b. a period (.) c. the cp name of the manager.
OBJECT-TYPE    
  DisplayString SIZE(0..17)  

ibmappnIsAcTimeMgrTimeValid 1.3.6.1.4.1.2.6.2.13.7.3.2.4.1.25
This indicates whether or not the the manager UTC times are valid. It is set by the manager if the manager determines the manager UTC times are valid.
OBJECT-TYPE    
  INTEGER notvalid(1), valid(2)  

ibmappnIsAcDataTable 1.3.6.1.4.1.2.6.2.13.7.3.2.5
Intermediate Session Accounting Data Table
OBJECT-TYPE    
  SEQUENCE OF  
    IbmappnIsAcDataEntry

ibmappnIsAcDataEntry 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1
Entry of Intermediate Session Accounting Data Table.
OBJECT-TYPE    
  IbmappnIsAcDataEntry  

ibmappnIsAcIndex 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.1
Session accounting record index. Upon initial startup, it will begin with 0, and increase up to maximum value of 2**31-1 (2,147,483,647), and wraps. Upon subsequent startups, it will be initialized with the value of the oldest index in any media type; or 0 if no indices are found.
OBJECT-TYPE    
  INTEGER  

ibmappnIsAcEntryType 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.2
Indicates whether the entry was made as the result of: 1. a session starting or, 2. a session ending or, 3. a session threshold reached or 4. a session checkpoint request
OBJECT-TYPE    
  INTEGER startEntry(1), endEntry(2), thresholdEntry(3), checkpointEntry(4)  

ibmappnIsAcRecTime 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.3
Intermediate Session Record time. It represents the time in hundreds of a second since the node was started. 2**32-1 (4,294,967,295), and wraps.
OBJECT-TYPE    
  TimeTicks  

ibmappnIsAcFqLuName 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.4
The network-qualified CP name or PU name of the node at which the session and pcid originated. For APPN and LEN nodes, this is either CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnIsAcPcid 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.5
The procedure correlation identifier (pcid) of a session. It is an 8-octet value assigned by the primary LU.
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

ibmappnIsAcPriLuName 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.6
Primary LU Name of the session.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnIsAcSecLuName 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.7
Secondary LU Name of the session.
OBJECT-TYPE    
  DisplayString SIZE(3..17)  

ibmappnIsAcModeName 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.8
The mode name used for this session
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnIsAcCosName 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.9
The class of service (cos) used for this session
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmappnIsAcTransPriority 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.10
Transmission priority for this session. The values are: 1. Low 2. Medium 3. High 4. Network
OBJECT-TYPE    
  INTEGER low(1), medium(2), high(3), network(4)  

ibmappnIsAcSessType 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.11
The type of intermediate session.
OBJECT-TYPE    
  INTEGER lu62(1), lu0thru3(2)  

ibmappnIsAcSessState 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.12
Indicates the state of the session. 1. session is pending inactive or, 2. session is pending active or, 3. session is active or, 4. session is inactive
OBJECT-TYPE    
  INTEGER inactive(1), pendactive(2), active(3), pendinact(4)  

ibmappnIsAcSessStartTime 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.13
Time when the session started in hundreds of a second.
OBJECT-TYPE    
  TimeTicks  

ibmappnIsAcSessUpTime 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.14
Length of time the session has been active in hundreds of a second.
OBJECT-TYPE    
  TimeTicks  

ibmappnIsAcCtrUpTime 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.15
Length of time the session counters have been active in hundreds of a second.
OBJECT-TYPE    
  TimeTicks  

ibmappnIsAcEndReason 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.16
The SNA sense code which resulted when the session ended.
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

ibmappnIsAcP2SFmdPius 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.17
The number of FMD PIU's sent from the primary LU to the secondary LU. The counter has a range of of 0 to 2**32; and then wraps.
OBJECT-TYPE    
  Counter  

ibmappnIsAcS2PFmdPius 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.18
The number of FMD PIU's sent from the secondary LU to the primary LU. The counter has a range of of 0 to 2**32; and then wraps.
OBJECT-TYPE    
  Counter  

ibmappnIsAcP2SNonFmdPius 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.19
The number of non-FMD PIU's sent from the primary LU to the secondary LU. The counter has a range of of 0 to 2**32; and then wraps.
OBJECT-TYPE    
  Counter  

ibmappnIsAcS2PNonFmdPius 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.20
The number of non-FMD PIU's sent from the secondary LU to the primary LU. The counter has a range of of 0 to 2**32; and then wraps.
OBJECT-TYPE    
  Counter  

ibmappnIsAcP2SFmdBytes 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.21
The number of FMD bytes sent from the primary LU to the secondary LU. The counter has a range of of 0 to 2**32; and then wraps.
OBJECT-TYPE    
  Counter  

ibmappnIsAcS2PFmdBytes 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.22
The number of FMD bytes sent from the secondary LU to the primary LU. The counter has a range of of 0 to 2**32; and then wraps.
OBJECT-TYPE    
  Counter  

ibmappnIsAcP2SNonFmdBytes 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.23
The number of non-FMD bytes sent from the primary LU to the secondary LU. The counter has a range of of 0 to 2**32; and then wraps.
OBJECT-TYPE    
  Counter  

ibmappnIsAcS2PNonFmdBytes 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.24
The number of non-FMD bytes sent from the secondary LU to the primary LU. The counter has a range of of 0 to 2**32; and then wraps.
OBJECT-TYPE    
  Counter  

ibmappnIsAcRouteInfo 1.3.6.1.4.1.2.6.2.13.7.3.2.5.1.25
The route selection control vector (RSCV x'2B') used for this session. It is present for APPN nodes; but is not present for LEN nodes.
OBJECT-TYPE    
  OCTET STRING  

ibmappnConversation 1.3.6.1.4.1.2.6.2.13.8
OBJECT IDENTIFIER    

ibmappnConvGeneral 1.3.6.1.4.1.2.6.2.13.8.1
OBJECT IDENTIFIER    

ibmappnConvEndPoint 1.3.6.1.4.1.2.6.2.13.8.2
OBJECT IDENTIFIER    

ibmrpq 1.3.6.1.4.1.2.6.2.14
OBJECT IDENTIFIER    

ibmtb 1.3.6.1.4.1.2.6.2.15
OBJECT IDENTIFIER    

ibmdot1dBase 1.3.6.1.4.1.2.6.2.15.1
OBJECT IDENTIFIER    

ibmdot1dBaseBridgeAddress 1.3.6.1.4.1.2.6.2.15.1.1
The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with ibmdot1dStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdot1dBaseNumPorts 1.3.6.1.4.1.2.6.2.15.1.2
The number of TB ports controlled by this bridging entity.
OBJECT-TYPE    
  INTEGER  

ibmdot1dBaseType 1.3.6.1.4.1.2.6.2.15.1.3
Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type.
OBJECT-TYPE    
  INTEGER unknown(1), transparent-only(2), sourceroute-only(3), srt(4)  

ibmdot1dBasePortTable 1.3.6.1.4.1.2.6.2.15.1.4
A table that contains generic information about every port that is associated with this bridge.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmDot1dBasePortEntry

ibmdot1dBasePortEntry 1.3.6.1.4.1.2.6.2.15.1.4.1
A list of information for each port of the bridge.
OBJECT-TYPE    
  IbmDot1dBasePortEntry  

ibmdot1dBasePort 1.3.6.1.4.1.2.6.2.15.1.4.1.1
The port number of the port for which this entry contains bridge management information.
OBJECT-TYPE    
  INTEGER  

ibmdot1dBasePortIfIndex 1.3.6.1.4.1.2.6.2.15.1.4.1.2
The value of the instance of the ifIndex object, defined in RFC 1156, RFC 1213 for the interface corresponding to this port.
OBJECT-TYPE    
  INTEGER  

ibmdot1dBasePortCircuit 1.3.6.1.4.1.2.6.2.15.1.4.1.3
For a port which potentially has the same value of ibmdot1dBasePortIfIndex as another port on the same bridge, this object contains an identifier unique to this port. For example, in the case where multiple ports correspond one-to-one with multiple Frame Relay circuit's, this value provides the object identifier for the frame relay MIB. Fpr a port which has a unique value of ibmdot1dBasePortIfIndex, this object can have the value {0.0}.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

ibmdot1dBasePortDelayExceededDiscards 1.3.6.1.4.1.2.6.2.15.1.4.1.4
The number of frames discarded by this port due to excessive transit delay through the bridge.
OBJECT-TYPE    
  Counter  

ibmdot1dBasePortMtuExceededDiscards 1.3.6.1.4.1.2.6.2.15.1.4.1.5
The number of frames discarded by this port due to an excessive size.
OBJECT-TYPE    
  Counter  

ibmdot1dStp 1.3.6.1.4.1.2.6.2.15.2
OBJECT IDENTIFIER    

ibmdot1dStpProtocolSpecification 1.3.6.1.4.1.2.6.2.15.2.1
An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
OBJECT-TYPE    
  INTEGER unknown(1), decLb100(2), ieee8021d(3)  

ibmdot1dStpPriority 1.3.6.1.4.1.2.6.2.15.2.2
The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of ibmdot1dBaseBridgeAddress.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmdot1dStpTimeSinceTopologyChange 1.3.6.1.4.1.2.6.2.15.2.3
The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
OBJECT-TYPE    
  TimeTicks  

ibmdot1dStpTopChanges 1.3.6.1.4.1.2.6.2.15.2.4
The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
OBJECT-TYPE    
  Counter  

ibmdot1dStpDesignatedRoot 1.3.6.1.4.1.2.6.2.15.2.5
The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

ibmdot1dStpRootCost 1.3.6.1.4.1.2.6.2.15.2.6
The cost of the path to the root as seen from this bridge.
OBJECT-TYPE    
  INTEGER  

ibmdot1dStpRootPort 1.3.6.1.4.1.2.6.2.15.2.7
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
OBJECT-TYPE    
  INTEGER  

ibmdot1dStpMaxAge 1.3.6.1.4.1.2.6.2.15.2.8
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
OBJECT-TYPE    
  INTEGER  

ibmdot1dStpHelloTime 1.3.6.1.4.1.2.6.2.15.2.9
The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
OBJECT-TYPE    
  INTEGER  

ibmdot1dStpHoldTime 1.3.6.1.4.1.2.6.2.15.2.10
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
OBJECT-TYPE    
  INTEGER  

ibmdot1dStpForwardDelay 1.3.6.1.4.1.2.6.2.15.2.11
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in a particular state before moving to the next state. For example, how long a port stays in the Listening state when moving from Blocking to Learning. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. (Note that this value is the one that this bridge is currently using, in contrast to ibmdot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.)
OBJECT-TYPE    
  INTEGER  

ibmdot1dStpBridgeMaxAge 1.3.6.1.4.1.2.6.2.15.2.12
The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1d/D9 specifies that the range for this parameter is related to the value of ibmdot1dStpBridgeHelloTime. The granularity of this timer is specified by 802.1d/D9 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds. The IBM 6611 Network Processor obtains this value from the 'Max Age' parameter provided to the configuration program.
OBJECT-TYPE    
  INTEGER  

ibmdot1dStpBridgeHelloTime 1.3.6.1.4.1.2.6.2.15.2.13
The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1d/D9 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds. The IBM 6611 Network Processor obtains this value from the 'Hello Time' parameter provided to the configuration program.
OBJECT-TYPE    
  INTEGER  

ibmdot1dStpBridgeForwardDelay 1.3.6.1.4.1.2.6.2.15.2.14
The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1d/D9 specifies that the range for this parameter is related to the value of ibmdot1dStpBridgeMaxAge. The granularity of this timer is specified by 802.1d/D9 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds. The IBM 6611 Network Processor obtains this value from the 'Forward Delay Time' parameter provided to the configuration program.
OBJECT-TYPE    
  INTEGER  

ibmdot1dStpPortTable 1.3.6.1.4.1.2.6.2.15.2.15
A table that contains port-specific information for the Spanning Tree Protocol.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmDot1dStpPortEntry

ibmdot1dStpPortEntry 1.3.6.1.4.1.2.6.2.15.2.15.1
A list of information maintained by every port about the Spanning Tree Protocol state for that port.
OBJECT-TYPE    
  IbmDot1dStpPortEntry  

ibmdot1dStpPort 1.3.6.1.4.1.2.6.2.15.2.15.1.1
The port number of the port for which this entry contains Spanning Tree Protocol management information. This port number is the same as that reported by ibmdot1dBasePort.
OBJECT-TYPE    
  INTEGER  

ibmdot1dStpPortPriority 1.3.6.1.4.1.2.6.2.15.2.15.1.2
The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of ibmdot1dStpPort.
OBJECT-TYPE    
  INTEGER 0..255  

ibmdot1dStpPortState 1.3.6.1.4.1.2.6.2.15.2.15.1.3
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see ibmdot1dStpPortEnable), this object will have a value of disabled(1).
OBJECT-TYPE    
  INTEGER disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)  

ibmdot1dStpPortEnable 1.3.6.1.4.1.2.6.2.15.2.15.1.4
The enabled/disabled status of the port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ibmdot1dStpPortPathCost 1.3.6.1.4.1.2.6.2.15.2.15.1.5
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. The IBM 6611 Network Processor obtains this value from the 'Path Cost' parameter provided to the configuration program.
OBJECT-TYPE    
  INTEGER 1..65535  

ibmdot1dStpPortDesignatedRoot 1.3.6.1.4.1.2.6.2.15.2.15.1.6
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

ibmdot1dStpPortDesignatedCost 1.3.6.1.4.1.2.6.2.15.2.15.1.7
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
OBJECT-TYPE    
  INTEGER  

ibmdot1dStpPortDesignatedBridge 1.3.6.1.4.1.2.6.2.15.2.15.1.8
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

ibmdot1dStpPortDesignatedPort 1.3.6.1.4.1.2.6.2.15.2.15.1.9
The Port Identifier of the port on the Designated Bridge for this port's segment.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmdot1dStpPortForwardTransitions 1.3.6.1.4.1.2.6.2.15.2.15.1.10
The number of times this port has transitioned from the Learning state to the Forwarding state.
OBJECT-TYPE    
  Counter  

ibmdot1dTp 1.3.6.1.4.1.2.6.2.15.3
OBJECT IDENTIFIER    

ibmdot1dTpLearnedEntryDiscards 1.3.6.1.4.1.2.6.2.15.3.1
The total number of Forwarding Database entries, which have been or would have been learnt, but have been discarded due to a lack of space to store them in the Forwarding Database. If this counter is increasing, it indicates that the Forwarding Database is regularly becoming full (a condition which has unpleasant performance effects on the subnetwork). If this counter has a significant value but is not presently increasing, it indicates that the problem has been occurring but is not persistent.
OBJECT-TYPE    
  Counter  

ibmdot1dTpAgingTime 1.3.6.1.4.1.2.6.2.15.3.2
The timeout period in seconds for aging out dynamically learned forwarding information. The IBM 6611 Network Processor obtains this value from the 'Aging Time' parameter provided to the configuration program.
OBJECT-TYPE    
  INTEGER  

ibmdot1dTpFdbTable 1.3.6.1.4.1.2.6.2.15.3.3
A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmDot1dTpFdbEntry

ibmdot1dTpFdbEntry 1.3.6.1.4.1.2.6.2.15.3.3.1
Information about a specific unicast MAC address for which the bridge has some forwarding and/or filtering information.
OBJECT-TYPE    
  IbmDot1dTpFdbEntry  

ibmdot1dTpFdbAddress 1.3.6.1.4.1.2.6.2.15.3.3.1.1
A unicast MAC address for which the bridge has forwarding and/or filtering information.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdot1dTpFdbPort 1.3.6.1.4.1.2.6.2.15.3.3.1.2
Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance of ibmdot1dTpFdbAddress has been seen. A value of '0' indicates that the port number has not been learned but that the bridge does have some forwarding/filtering information about this address (e.g. in the ibmdot1dStaticTable). Implementors are encouraged to assign the port value to this object whenever it is learned even for addresses for which the corresponding value of ibmdot1dTpFdbStatus is not learned(3).
OBJECT-TYPE    
  INTEGER  

ibmdot1dTpFdbStatus 1.3.6.1.4.1.2.6.2.15.3.3.1.3
The status of this entry. The meanings of the values are: other(1) : none of the following. This would include the case where some other MIB object (not the corresponding instance of ibmdot1dTpFdbPort, nor an entry in the ibmdot1dStaticTable) is being used to determine if and how frames addressed to the value of the corresponding instance of ibmdot1dTpFdbAddress are being forwarded. invalid(2) : this entry is not longer valid (e.g., it was learned but has since aged-out), but has not yet been flushed from the table. learned(3) : the value of the corresponding instance of ibmdot1dTpFdbPort was learned, and is being used. self(4) : the value of the corresponding instance of ibmdot1dTpFdbAddress represents one of the bridge's addresses. The corresponding instance of ibmdot1dTpFdbPort indicates which of the bridge's ports has this address. mgmt(5) : the value of the corresponding instance of ibmdot1dTpFdbAddress is also the value of an existing instance of ibmdot1dStaticAddress.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), learned(3), self(4), mgmt(5)  

ibmdot1dTpPortTable 1.3.6.1.4.1.2.6.2.15.3.4
A table that contains information about every port that is associated with this transparent bridge.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmDot1dTpPortEntry

ibmdot1dTpPortEntry 1.3.6.1.4.1.2.6.2.15.3.4.1
A list of information for each port of a transparent bridge.
OBJECT-TYPE    
  IbmDot1dTpPortEntry  

ibmdot1dTpPort 1.3.6.1.4.1.2.6.2.15.3.4.1.1
The port number of the port for which this entry contains Transparent bridging management information.
OBJECT-TYPE    
  INTEGER  

ibmdot1dTpPortMaxInfo 1.3.6.1.4.1.2.6.2.15.3.4.1.2
The maximum size of the INFO (non-MAC) field that this port will receive or transmit.
OBJECT-TYPE    
  INTEGER  

ibmdot1dTpPortInFrames 1.3.6.1.4.1.2.6.2.15.3.4.1.3
The number of frames that have been received by this port from its segment. Note that a frame received on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function.
OBJECT-TYPE    
  Counter  

ibmdot1dTpPortOutFrames 1.3.6.1.4.1.2.6.2.15.3.4.1.4
The number of frames that have been transmitted by this port to its segment. Note that a frame transmitted on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function.
OBJECT-TYPE    
  Counter  

ibmdot1dTpPortInDiscards 1.3.6.1.4.1.2.6.2.15.3.4.1.5
Count of valid frames received which were discarded (i.e., filtered) by the Forwarding Process.
OBJECT-TYPE    
  Counter  

ibmdot1dStatic 1.3.6.1.4.1.2.6.2.15.4
OBJECT IDENTIFIER    

ibmdot1dStaticTable 1.3.6.1.4.1.2.6.2.15.4.1
A table containing filtering information configured into the bridge by (local or network) management specifying the set of ports to which frames received from specific ports and containing specific destination addresses are allowed to be forwarded. The value of zero in this table as the port number from which frames with a specific destination address are received, is used to specify all ports for which there is no specific entry in this table for that particular destination address. Entries are valid for unicast and for group/broadcast addresses.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmDot1dStaticEntry

ibmdot1dStaticEntry 1.3.6.1.4.1.2.6.2.15.4.1.1
Filtering information configured into the bridge by (local or network) management specifying the set of ports to which frames received from a specific port and containing a specific destination address are allowed to be forwarded.
OBJECT-TYPE    
  IbmDot1dStaticEntry  

ibmdot1dStaticAddress 1.3.6.1.4.1.2.6.2.15.4.1.1.1
The destination MAC address in a frame to which this entry's filtering information applies. This object can take the value of a unicast address, a group address or the broadcast address.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdot1dStaticReceivePort 1.3.6.1.4.1.2.6.2.15.4.1.1.2
Either the value '0', or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of zero indicates that this entry applies on all ports of the bridge for which there is no other applicable entry.
OBJECT-TYPE    
  INTEGER  

ibmdot1dStaticAllowedToGoTo 1.3.6.1.4.1.2.6.2.15.4.1.1.3
The set of ports to which frames received from a specific port and destined for a specific MAC address, are allowed to be forwarded. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. (Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant.)
OBJECT-TYPE    
  OCTET STRING  

ibmdot1dStaticStatus 1.3.6.1.4.1.2.6.2.15.4.1.1.4
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object removes the corresponding entry. permanent(3) - this entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset(4) - this entry is currently in use and will remain so until the next reset of the bridge. deleteOnTimeout(5) - this entry is currently in use and will remain so until it is aged out.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), permanent(3), deleteOnReset(4), deleteOnTimeout(5)  

ibmtbMACAddressFilters 1.3.6.1.4.1.2.6.2.15.5
OBJECT IDENTIFIER    

ibmtbmacFiltInfoTable 1.3.6.1.4.1.2.6.2.15.5.1
Table of MAC address filtering information.
OBJECT-TYPE    
  SEQUENCE OF  
    TBMacAddrFilterInfoEntry

ibmtbmacFiltInfoEntry 1.3.6.1.4.1.2.6.2.15.5.1.1
MAC address filtering information for a single interface.
OBJECT-TYPE    
  TBMacAddrFilterInfoEntry  

ibmtbmacFiltIfIndex 1.3.6.1.4.1.2.6.2.15.5.1.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmtbmacFiltInFilterType 1.3.6.1.4.1.2.6.2.15.5.1.1.2
For the incoming filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmtbmacFiltOutFilterType 1.3.6.1.4.1.2.6.2.15.5.1.1.3
For the outgoing filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmtbmacFiltInNotForwarded 1.3.6.1.4.1.2.6.2.15.5.1.1.4
Number of packets not forwarded, in the incoming direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmtbmacFiltOutNotForwarded 1.3.6.1.4.1.2.6.2.15.5.1.1.5
Number of packets not forwarded, in the outgoing direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmtbmacFiltInTable 1.3.6.1.4.1.2.6.2.15.5.2
Table of MAC address filtering information for incoming frames.
OBJECT-TYPE    
  SEQUENCE OF  
    TBMacAddrFilterInEntry

ibmtbmacFiltInEntry 1.3.6.1.4.1.2.6.2.15.5.2.1
Filtering information for incoming frames.
OBJECT-TYPE    
  TBMacAddrFilterInEntry  

ibmtbmacFiltInIfIndex 1.3.6.1.4.1.2.6.2.15.5.2.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmtbmacFiltInSrcAddress 1.3.6.1.4.1.2.6.2.15.5.2.1.2
MAC source address to be filtered.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmtbmacFiltInSrcMask 1.3.6.1.4.1.2.6.2.15.5.2.1.3
Mask to allow ibmtbmacFiltInSrcAddress to be used as a range of values.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmtbmacFiltInDestAddress 1.3.6.1.4.1.2.6.2.15.5.2.1.4
MAC destination address to be filtered.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmtbmacFiltInDestMask 1.3.6.1.4.1.2.6.2.15.5.2.1.5
Mask to allow ibmtbmacFiltInDestAddress to be used as a range of values.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmtbmacFiltOutTable 1.3.6.1.4.1.2.6.2.15.5.3
Table of MAC address filtering information for outgoing frames.
OBJECT-TYPE    
  SEQUENCE OF  
    TBMacAddrFilterOutEntry

ibmtbmacFiltOutEntry 1.3.6.1.4.1.2.6.2.15.5.3.1
Filtering information for outgoing frames.
OBJECT-TYPE    
  TBMacAddrFilterOutEntry  

ibmtbmacFiltOutIfIndex 1.3.6.1.4.1.2.6.2.15.5.3.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmtbmacFiltOutSrcAddress 1.3.6.1.4.1.2.6.2.15.5.3.1.2
MAC source address to be filtered.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmtbmacFiltOutSrcMask 1.3.6.1.4.1.2.6.2.15.5.3.1.3
Mask to allow ibmtbmacFiltOutSrcAddress to be used as a range of values.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmtbmacFiltOutDestAddress 1.3.6.1.4.1.2.6.2.15.5.3.1.4
MAC destination address to be filtered.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmtbmacFiltOutDestMask 1.3.6.1.4.1.2.6.2.15.5.3.1.5
Mask to allow ibmtbmacFiltOutDestAddress to be used as a range of values.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmtbSAPFilters 1.3.6.1.4.1.2.6.2.15.6
OBJECT IDENTIFIER    

ibmtbsapFiltInfoTable 1.3.6.1.4.1.2.6.2.15.6.1
Table of SAP filtering information.
OBJECT-TYPE    
  SEQUENCE OF  
    TBSapFilterInfoEntry

ibmtbsapFiltInfoEntry 1.3.6.1.4.1.2.6.2.15.6.1.1
SAP filtering information for a single interface.
OBJECT-TYPE    
  TBSapFilterInfoEntry  

ibmtbsapFiltIfIndex 1.3.6.1.4.1.2.6.2.15.6.1.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmtbsapFiltIn 1.3.6.1.4.1.2.6.2.15.6.1.1.2
A bitmap of all possible source SAPs (even) that will be on or off depending on whether or not an incoming frame with that SAP is to be forwarded.
OBJECT-TYPE    
  OCTET STRING SIZE(16)  

ibmtbsapFiltOut 1.3.6.1.4.1.2.6.2.15.6.1.1.3
A bitmap of all possible source SAPs (even) that will be on or off depending on whether or not an outgoing frame with that SAP is to be forwarded.
OBJECT-TYPE    
  OCTET STRING SIZE(16)  

ibmtbsapFiltInNotForwarded 1.3.6.1.4.1.2.6.2.15.6.1.1.4
Number of packets not forwarded, in the incoming direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmtbsapFiltOutNotForwarded 1.3.6.1.4.1.2.6.2.15.6.1.1.5
Number of packets not forwarded, in the outgoing direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmtbEthTypeFilters 1.3.6.1.4.1.2.6.2.15.7
OBJECT IDENTIFIER    

ibmtbEthTypeFiltInfoTable 1.3.6.1.4.1.2.6.2.15.7.1
Table of Ethernet type filtering information. Note that this filtering only applies to: 1) The Ethernet TYPE field for DIX version 2 frames. 2) The Ethernet TYPE field contained in the SNAP header of 802.3 frames, if the frame contains a SNAP header (SSAP = DSAP = 0xAA)
OBJECT-TYPE    
  SEQUENCE OF  
    TBEthTypeFilterInfoEntry

ibmtbEthTypeFiltInfoEntry 1.3.6.1.4.1.2.6.2.15.7.1.1
Ethernet type filtering information for a single interface.
OBJECT-TYPE    
  TBEthTypeFilterInfoEntry  

ibmtbEthTypeFiltIfIndex 1.3.6.1.4.1.2.6.2.15.7.1.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmtbEthTypeFiltInFilterType 1.3.6.1.4.1.2.6.2.15.7.1.1.2
For the incoming Ethernet type filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmtbEthTypeFiltOutFilterType 1.3.6.1.4.1.2.6.2.15.7.1.1.3
For the outgoing Ethernet type filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmtbEthTypeFiltInNotForwarded 1.3.6.1.4.1.2.6.2.15.7.1.1.4
Number of packets not forwarded, in the incoming direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmtbEthTypeFiltOutNotForwarded 1.3.6.1.4.1.2.6.2.15.7.1.1.5
Number of packets not forwarded, in the outgoing direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmtbEthTypeFiltInTable 1.3.6.1.4.1.2.6.2.15.7.2
Table of Ethernet type filtering information for incoming frames. Note that this filtering only applies to: 1) The Ethernet TYPE field for DIX version 2 frames. 2) The Ethernet TYPE field contained in the SNAP header of 802.3 frames, if the frame contains a SNAP header (SSAP = DSAP = 0xAA)
OBJECT-TYPE    
  SEQUENCE OF  
    TBEthTypeFilterInEntry

ibmtbEthTypeFiltInEntry 1.3.6.1.4.1.2.6.2.15.7.2.1
Filtering information for a single Ethernet type on a single interface.
OBJECT-TYPE    
  TBEthTypeFilterInEntry  

ibmtbEthTypeFiltInIfIndex 1.3.6.1.4.1.2.6.2.15.7.2.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmtbEthTypeFiltInValue 1.3.6.1.4.1.2.6.2.15.7.2.1.2
Indicates which Ethernet type to filter.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmtbEthTypeFiltInMask 1.3.6.1.4.1.2.6.2.15.7.2.1.3
Mask to allow ibmtbEthTypeFiltInValue to be used as a range of values.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmtbEthTypeFiltOutTable 1.3.6.1.4.1.2.6.2.15.7.3
Table of Ethernet type filtering information for outgoing frames. Note that this filtering only applies to: 1) The Ethernet TYPE field for DIX version 2 frames. 2) The Ethernet TYPE field contained in the SNAP header of 802.3 frames, if the frame contains a SNAP header (SSAP = DSAP = 0xAA)
OBJECT-TYPE    
  SEQUENCE OF  
    TBEthTypeFilterOutEntry

ibmtbEthTypeFiltOutEntry 1.3.6.1.4.1.2.6.2.15.7.3.1
Filtering information for a single Ethernet type on a single interface.
OBJECT-TYPE    
  TBEthTypeFilterOutEntry  

ibmtbEthTypeFiltOutIfIndex 1.3.6.1.4.1.2.6.2.15.7.3.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmtbEthTypeFiltOutValue 1.3.6.1.4.1.2.6.2.15.7.3.1.2
Indicates which Ethernet type to filter.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmtbEthTypeFiltOutMask 1.3.6.1.4.1.2.6.2.15.7.3.1.3
Mask to allow ibmtbEthTypeFiltOutValue to be used as a range of values.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmtbWindowFilters 1.3.6.1.4.1.2.6.2.15.8
OBJECT IDENTIFIER    

ibmtbwinFiltInfoTable 1.3.6.1.4.1.2.6.2.15.8.1
Table of Window filtering information.
OBJECT-TYPE    
  SEQUENCE OF  
    TBWindowFilterInfoEntry

ibmtbwinFiltInfoEntry 1.3.6.1.4.1.2.6.2.15.8.1.1
Window filtering information for a single interface.
OBJECT-TYPE    
  TBWindowFilterInfoEntry  

ibmtbwinFiltIfIndex 1.3.6.1.4.1.2.6.2.15.8.1.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmtbwinFiltInFilterType 1.3.6.1.4.1.2.6.2.15.8.1.1.2
For the incoming filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmtbwinFiltOutFilterType 1.3.6.1.4.1.2.6.2.15.8.1.1.3
For the outgoing filter table, determines whether the entries are permit or deny entries.
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ibmtbwinFiltInNotForwarded 1.3.6.1.4.1.2.6.2.15.8.1.1.4
Number of packets not forwarded, in the incoming direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmtbwinFiltOutNotForwarded 1.3.6.1.4.1.2.6.2.15.8.1.1.5
Number of packets not forwarded, in the outgoing direction, because they were filtered out.
OBJECT-TYPE    
  Counter  

ibmtbwinFiltInTable 1.3.6.1.4.1.2.6.2.15.8.2
Table of Window filtering information for incoming frames.
OBJECT-TYPE    
  SEQUENCE OF  
    TBWindowFilterInEntry

ibmtbwinFiltInEntry 1.3.6.1.4.1.2.6.2.15.8.2.1
Filtering information for incoming frames.
OBJECT-TYPE    
  TBWindowFilterInEntry  

ibmtbwinFiltInIfIndex 1.3.6.1.4.1.2.6.2.15.8.2.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmtbwinFiltInContents 1.3.6.1.4.1.2.6.2.15.8.2.1.2
String of bytes that will be compared with bytes in the frame.
OBJECT-TYPE    
  OCTET STRING  

ibmtbwinFiltInMaskString 1.3.6.1.4.1.2.6.2.15.8.2.1.3
String of bytes that will be masked with bytes in the contents field.
OBJECT-TYPE    
  OCTET STRING  

ibmtbwinFiltInOffsetStart 1.3.6.1.4.1.2.6.2.15.8.2.1.4
Determines the starting point where the contents field should be applied. A value of 'MAC' means the base is at the beginning of the destination MAC address field, whereas, a value of 'DATA' means it is applied at the beginning of the data field.
OBJECT-TYPE    
  DisplayString  

ibmtbwinFiltInNumBytes 1.3.6.1.4.1.2.6.2.15.8.2.1.5
Number of bytes in the contents field that are used for filtering
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ibmtbwinFiltInOffset 1.3.6.1.4.1.2.6.2.15.8.2.1.6
Number of bytes offset into the frame from the offset start point to begin the compare.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmtbwinFiltInId 1.3.6.1.4.1.2.6.2.15.8.2.1.7
A unique identifier associated with this window filter entry.
OBJECT-TYPE    
  INTEGER  

ibmtbwinFiltOutTable 1.3.6.1.4.1.2.6.2.15.8.3
Table of Window filtering information for outgoing frames.
OBJECT-TYPE    
  SEQUENCE OF  
    TBWindowFilterOutEntry

ibmtbwinFiltOutEntry 1.3.6.1.4.1.2.6.2.15.8.3.1
Filtering information for outgoing frames.
OBJECT-TYPE    
  TBWindowFilterOutEntry  

ibmtbwinFiltOutIfIndex 1.3.6.1.4.1.2.6.2.15.8.3.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmtbwinFiltOutContents 1.3.6.1.4.1.2.6.2.15.8.3.1.2
String of bytes that will be compared with bytes in the frame.
OBJECT-TYPE    
  OCTET STRING  

ibmtbwinFiltOutMaskString 1.3.6.1.4.1.2.6.2.15.8.3.1.3
String of bytes that will be masked with bytes in the contents field.
OBJECT-TYPE    
  OCTET STRING  

ibmtbwinFiltOutOffsetStart 1.3.6.1.4.1.2.6.2.15.8.3.1.4
Determines the starting point where the contents field should be applied. A value of 'MAC' means the base is at the beginning of the destination MAC address field, whereas, a value of 'DATA' means it is applied at the beginning of the data field.
OBJECT-TYPE    
  DisplayString  

ibmtbwinFiltOutNumBytes 1.3.6.1.4.1.2.6.2.15.8.3.1.5
Number of bytes in the contents field that are used for filtering
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ibmtbwinFiltOutOffset 1.3.6.1.4.1.2.6.2.15.8.3.1.6
Number of bytes offset into the frame from the offset start point to begin the compare.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmtbwinFiltOutId 1.3.6.1.4.1.2.6.2.15.8.3.1.7
A unique identifier associated with this window filter entry.
OBJECT-TYPE    
  INTEGER  

ibmtbFiltOrderTable 1.3.6.1.4.1.2.6.2.15.9
OBJECT IDENTIFIER    

ibmtbFiltOrderInTable 1.3.6.1.4.1.2.6.2.15.9.1
Table of information describing which order the filters are applied for incoming frames.
OBJECT-TYPE    
  SEQUENCE OF  
    TBFiltOrderInEntry

ibmtbFiltOrderInEntry 1.3.6.1.4.1.2.6.2.15.9.1.1
Filter order information for incoming frames.
OBJECT-TYPE    
  TBFiltOrderInEntry  

ibmtbFiltOrderInIfIndex 1.3.6.1.4.1.2.6.2.15.9.1.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmtbFiltOrderInPriority 1.3.6.1.4.1.2.6.2.15.9.1.1.2
The priority of when a filter is applied to an incoming frame. A value of 1 signifies that it is applied first.
OBJECT-TYPE    
  INTEGER  

ibmtbFiltOrderInName 1.3.6.1.4.1.2.6.2.15.9.1.1.3
The name of the filter applied to incoming frames that is associated with the priority, ibmtbFiltOrderInPriority.
OBJECT-TYPE    
  DisplayString  

ibmtbFiltOrderOutTable 1.3.6.1.4.1.2.6.2.15.9.2
Table of information describing which order the filters are applied for outgoing frames.
OBJECT-TYPE    
  SEQUENCE OF  
    TBFiltOrderOutEntry

ibmtbFiltOrderOutEntry 1.3.6.1.4.1.2.6.2.15.9.2.1
Filter order information for outgoing frames.
OBJECT-TYPE    
  TBFiltOrderOutEntry  

ibmtbFiltOrderOutIfIndex 1.3.6.1.4.1.2.6.2.15.9.2.1.1
The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object for the same interface.
OBJECT-TYPE    
  INTEGER  

ibmtbFiltOrderOutPriority 1.3.6.1.4.1.2.6.2.15.9.2.1.2
The priority of when a filter is applied to an outgoing frame. A value of 1 signifies that it is applied first.
OBJECT-TYPE    
  INTEGER  

ibmtbFiltOrderOutName 1.3.6.1.4.1.2.6.2.15.9.2.1.3
The name of the filter applied to outgoing frames that is associated with the priority, ibmtbFiltOrderOutPriority.
OBJECT-TYPE    
  DisplayString  

ibmapple 1.3.6.1.4.1.2.6.2.16
OBJECT IDENTIFIER    

ibmSelectNet 1.3.6.1.4.1.2.6.2.16.1
OBJECT IDENTIFIER    

ibmSelectNetTable 1.3.6.1.4.1.2.6.2.16.1.1
The list of selected network definition entries.
OBJECT-TYPE    
  SEQUENCE OF  
    SelectNetEntry

ibmSelectNetEntry 1.3.6.1.4.1.2.6.2.16.1.1.1
The description of a selected network definition.
OBJECT-TYPE    
  SelectNetEntry  

ibmSelectNetIndex 1.3.6.1.4.1.2.6.2.16.1.1.1.1
An identifier that is unique to the default zone name that is present in this entry.
OBJECT-TYPE    
  INTEGER  

ibmSelectNetZone 1.3.6.1.4.1.2.6.2.16.1.1.1.2
The ASCII default zone name of this entry.
OBJECT-TYPE    
  OCTET STRING  

ibmSelectNetNetStart 1.3.6.1.4.1.2.6.2.16.1.1.1.3
The network address that starts the range for this entry. This address is a two octet DDP network address in network byte order.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmSelectNetNetEnd 1.3.6.1.4.1.2.6.2.16.1.1.1.4
The network address that ends the range for this entry. This address is a two octet DDP network address in network byte order.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmSelectNetInterfaceNetStart 1.3.6.1.4.1.2.6.2.16.1.1.1.5
The network address that starts the range for the interface associated with this definition.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmnbpFilter 1.3.6.1.4.1.2.6.2.16.2
OBJECT IDENTIFIER    

ibmnbpFilterPacketsFiltered 1.3.6.1.4.1.2.6.2.16.2.1
The number of packets filtered by nbp filters.
OBJECT-TYPE    
  Counter  

ibmnbpFilterPacketsSent 1.3.6.1.4.1.2.6.2.16.2.2
The number of packets not filtered by nbp filters.
OBJECT-TYPE    
  Counter  

ibmatportFilter 1.3.6.1.4.1.2.6.2.16.3
OBJECT IDENTIFIER    

ibmatportFilterTable 1.3.6.1.4.1.2.6.2.16.3.1
The list of Appletalk port destination network filter entries.
OBJECT-TYPE    
  SEQUENCE OF  
    AtportFilterEntry

ibmatportFilterEntry 1.3.6.1.4.1.2.6.2.16.3.1.1
The description of a filter on this Appletalk port.
OBJECT-TYPE    
  AtportFilterEntry  

ibmatportFilterIndex 1.3.6.1.4.1.2.6.2.16.3.1.1.1
An identifier that is unique to the Appletalk port to which this filter applies. The port identified by this value is the same port as identified by atportIndex.
OBJECT-TYPE    
  INTEGER  

ibmatportFilterNetStart 1.3.6.1.4.1.2.6.2.16.3.1.1.2
The network address that starts the range for this destination network filter. This address is a two octet DDP network address in network byte order.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmatportFilterNetEnd 1.3.6.1.4.1.2.6.2.16.3.1.1.3
The network address that ends the range for this destination network filter. This address is a two octet DDP network address in network byte order.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmSelectNetFilter 1.3.6.1.4.1.2.6.2.16.4
OBJECT IDENTIFIER    

ibmSelectNetFilterTable 1.3.6.1.4.1.2.6.2.16.4.1
The list of selected network destination network filter entries.
OBJECT-TYPE    
  SEQUENCE OF  
    SelectNetFilterEntry

ibmSelectNetFilterEntry 1.3.6.1.4.1.2.6.2.16.4.1.1
The description of a filter for this selected network definition.
OBJECT-TYPE    
  SelectNetFilterEntry  

ibmSelectNetFilterIndex 1.3.6.1.4.1.2.6.2.16.4.1.1.1
An identifier that is unique to the selected network definition to which this filter applies. This value is the same as that provided by ibmSelectNetIndex.
OBJECT-TYPE    
  INTEGER  

ibmSelectNetFilterNetStart 1.3.6.1.4.1.2.6.2.16.4.1.1.2
The network address that starts the range for this destination network filter. This address is a two octet DDP network address in network byte order.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmSelectNetFilterNetEnd 1.3.6.1.4.1.2.6.2.16.4.1.1.3
The network address that ends the range for this destination network filter. This address is a two octet DDP network address in network byte order.
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

ibmdec 1.3.6.1.4.1.2.6.2.17
OBJECT IDENTIFIER    

ibmdecAllRoutersFuncAddr 1.3.6.1.4.1.2.6.2.17.1
The functional address used in communicating with with all DECnet Phase IV and DECnet Phase IV-Prime routers on a token ring LAN.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdecAllEndNodesFuncAddr 1.3.6.1.4.1.2.6.2.17.2
The functional address used in communicating with with all DECnet Phase IV and DECnet Phase IV-Prime end nodes on a token ring LAN.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ibmdecSplitHorPoisonRev 1.3.6.1.4.1.2.6.2.17.3
Defines whether the Split Horizon with Poison Reverse option is enabled or not
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ibmdecNodeType 1.3.6.1.4.1.2.6.2.17.4
This parameter indicates the node type of the router. This object is the same as the phivRouteType object defined by RFC 1289, however, this definition extends the enumerations to provide new values.
OBJECT-TYPE    
  INTEGER routing-III(1), nonrouting-III(2), area(3), routing-IV(4), nonrouting-IV(5), area-IV-Prime(6), routing-IV-Prime(7), nonrouting-IV-Prime(8)  

ibmdecLANCircuitTable 1.3.6.1.4.1.2.6.2.17.5
The list of information relevant to LAN circuits. This table extends the information provided by the phivCircuitParametersTable defined by RFC 1289.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmdecLANCircuitEntry

ibmdecLANCircuitEntry 1.3.6.1.4.1.2.6.2.17.5.1
Table entry with information relevant to LAN circuits.
OBJECT-TYPE    
  IbmdecLANCircuitEntry  

ibmdecLANCircuitIndex 1.3.6.1.4.1.2.6.2.17.5.1.1
A unique index value for each known circuit on a LAN interface. The value of this variable is the same as that provided by phivCircuitIndex.
OBJECT-TYPE    
  INTEGER  

ibmdecLANCircuitType 1.3.6.1.4.1.2.6.2.17.5.1.2
If the CircuitType is Bilingual for a circuit, the router would use a Phase_IV compliant locally administered MAC address for that circuit and would be configured to communicate with Phase_IV and Phase_IV-Prime nodes over that circuit. A bilingual router can help communication between the Phase_IV and the Phase_IV-Prime nodes over the same extended LAN segment, and prevents a partitioned network. If the CircuitType is AMA ( Arbitrary MAC Address ) for a circuit, the router would use an arbitrary MAC address for that circuit, and would be configured to communicate with Phase_IV-Prime nodes over that circuit. If the CircuitType is PhaseIV for a circuit, the router would use the Phase_IV compliant locally administered MAC address for that circuit, and would be configured to communicate with Phase_IV nodes over that circuit.
OBJECT-TYPE    
  INTEGER bilingual(1), ama(2), phaseIV(3)  

ibmdecLANCircuitSourceRoute 1.3.6.1.4.1.2.6.2.17.5.1.3
This parameter indicates if source routing is enabled on a token-ring circuit. A value of 3 is returned for circuits which are not of the 802.5/token-ring type.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notapplicable(3)  

ibmdecLANCircuitAddrType 1.3.6.1.4.1.2.6.2.17.5.1.4
This parameter indicates the type of MAC address used on this circuit. The value returned is decnet(1), if a DECnet Phase_IV compliant locally administered MAC address is being used. The value returned is hardware(2), if the unique assigned ROM address is used. The value returned is user(3), if a non DECnet Phase_IV compliant locally administered MAC address is being used.
OBJECT-TYPE    
  INTEGER decnet(1), hardware(2), user(3)  

ibmvines 1.3.6.1.4.1.2.6.2.18
OBJECT IDENTIFIER    

ibmvSysConfig 1.3.6.1.4.1.2.6.2.18.1
OBJECT IDENTIFIER    

ibmvSysRtr 1.3.6.1.4.1.2.6.2.18.1.1
Indicates whether this node is acting as a VINES router.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ibmvRouterName 1.3.6.1.4.1.2.6.2.18.1.2
The name of the router node, up to 15 characters long.
OBJECT-TYPE    
  DisplayString  

ibmvRouterNetid 1.3.6.1.4.1.2.6.2.18.1.3
The VINES network ID of the router node equal to the router node's serial number. This id may be up to 4 bytes in length.
OBJECT-TYPE    
  INTEGER  

ibmvIP 1.3.6.1.4.1.2.6.2.18.2
OBJECT IDENTIFIER    

ibmvipTotalIn 1.3.6.1.4.1.2.6.2.18.2.1
The total number of VINES IP packets that the router node has received since the last reboot.
OBJECT-TYPE    
  Counter  

ibmvipTotalOut 1.3.6.1.4.1.2.6.2.18.2.2
The total number of VINES IP packets that the router node has sent since the last reboot.
OBJECT-TYPE    
  Counter  

ibmvipRouted 1.3.6.1.4.1.2.6.2.18.2.3
The total number of packets that were routed to another node since the last reboot.
OBJECT-TYPE    
  Counter  

ibmvipBcast 1.3.6.1.4.1.2.6.2.18.2.4
The number of VINES IP broadcast packets sent, both generated from the router node and routed from other nodes, since the last reboot.
OBJECT-TYPE    
  Counter  

ibmvipInReceives 1.3.6.1.4.1.2.6.2.18.2.5
The number of unicast VINES IP packets received since the last reboot. A unicast packet is destined for this particular router node. It is not being forwarded, multicasted or broadcasted.
OBJECT-TYPE    
  Counter  

ibmvipBcastInReceives 1.3.6.1.4.1.2.6.2.18.2.6
The number of VINES IP broadcast packets received since the last reboot.
OBJECT-TYPE    
  Counter  

ibmvipBad 1.3.6.1.4.1.2.6.2.18.2.7
The total number of badly formed packets that the router node has received since the last booted.
OBJECT-TYPE    
  Counter  

ibmvipBadHeaders 1.3.6.1.4.1.2.6.2.18.2.8
The number of incoming VINES IP packets received since the last reboot which contained a header error; excluding the following errors: length, checksum and time to live.
OBJECT-TYPE    
  Counter  

ibmvipTooSmalls 1.3.6.1.4.1.2.6.2.18.2.9
The number of VINES IP packets received since the last reboot with len < the size of a VINES IP header.
OBJECT-TYPE    
  Counter  

ibmvipBadLens 1.3.6.1.4.1.2.6.2.18.2.10
The number of VINES IP packets received since the last reboot whose packet size is not equal to the number of bytes specified in the VINES IP header field.
OBJECT-TYPE    
  Counter  

ibmvipBadSums 1.3.6.1.4.1.2.6.2.18.2.11
The number of VINES IP packets received since the last reboot with a bad checksum.
OBJECT-TYPE    
  Counter  

ibmvipInDiscards 1.3.6.1.4.1.2.6.2.18.2.12
The number of incoming VINES IP packets discarded since the last reboot due to lack of resources.
OBJECT-TYPE    
  Counter  

ibmvipZeroHops 1.3.6.1.4.1.2.6.2.18.2.13
The number of VINES IP packets discarded since the last reboot because the hop count equals zero and the current node is not the destination.
OBJECT-TYPE    
  Counter  

ibmvipOutNoRoutes 1.3.6.1.4.1.2.6.2.18.2.14
The number of outgoing VINES IP packets discarded since the last reboot because no route is available.
OBJECT-TYPE    
  Counter  

ibmvNeighbor 1.3.6.1.4.1.2.6.2.18.3
OBJECT IDENTIFIER    

ibmvARP 1.3.6.1.4.1.2.6.2.18.3.1
OBJECT IDENTIFIER    

ibmvarpQueryReqs 1.3.6.1.4.1.2.6.2.18.3.1.1
The number of query requests received from clients since the last reboot. When a client is first booted up, it sends out a broadcast query request packet on its LAN segment.
OBJECT-TYPE    
  Counter  

ibmvarpServiceResps 1.3.6.1.4.1.2.6.2.18.3.1.2
The number of ARP query responses sent out from this router node since the last reboot. Each router node on the same LAN segment that is providing address assignments will respond.
OBJECT-TYPE    
  Counter  

ibmvarpAssignReqs 1.3.6.1.4.1.2.6.2.18.3.1.3
The number of ARP assignment request received from clients since the last reboot. The client issues an assignment request packet to the router node that responded first to the query request.
OBJECT-TYPE    
  Counter  

ibmvarpAssignResps 1.3.6.1.4.1.2.6.2.18.3.1.4
The number of ARP assignment responses sent to clients since the last reboot. The router node issues a VINES internet address for the client and sends it back in an assignment response packet.
OBJECT-TYPE    
  Counter  

ibmvarpHeaderError 1.3.6.1.4.1.2.6.2.18.3.1.5
The number of ARP packets received since the last reboot with a header error.
OBJECT-TYPE    
  Counter  

ibmvNbrNumber 1.3.6.1.4.1.2.6.2.18.3.2
The number of entries in the neighbor table.
OBJECT-TYPE    
  INTEGER  

ibmvNbrTable 1.3.6.1.4.1.2.6.2.18.3.3
A list of information about IBM's VINES router neighbor table.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmvNbrEntry

ibmvNbrEntry 1.3.6.1.4.1.2.6.2.18.3.3.1
The information for each entry in the neighbor table.
OBJECT-TYPE    
  IbmvNbrEntry  

ibmvNbrNetid 1.3.6.1.4.1.2.6.2.18.3.3.1.1
The network ID of the neighbor. The VINES internet address has the following form: 'nnnnnnnn.ssss'hex, where n = network ID and s = subnetwork ID. If the neighbor is a router, then network ID is the router node's (the neighbor's) serial number.
OBJECT-TYPE    
  OCTET STRING  

ibmvNbrSubNetid 1.3.6.1.4.1.2.6.2.18.3.3.1.2
The subnetwork ID of the neighbor. The VINES internet address has the following form: 'nnnnnnnn.ssss'hex, where n = network ID and s = subnetwork ID. If the neighbor is a router node, then the subnetwork ID for the router node (the neighbor) is 1.
OBJECT-TYPE    
  OCTET STRING  

ibmvNbrType 1.3.6.1.4.1.2.6.2.18.3.3.1.3
The type of the neighbor (workstation = pc).
OBJECT-TYPE    
  INTEGER server(1), workstation(2)  

ibmvNbrIfType 1.3.6.1.4.1.2.6.2.18.3.3.1.4
The type of interface that the server uses to reach the neighbor.
OBJECT-TYPE    
  INTEGER other(1), regular1822(2), hdh1822(3), ddn-x25(4), rfc877-x25(5), ethernet-csmacd(6), iso88023-csmacd(7), iso88024-tokenBus(8), iso88025-tokenRing(9), iso88026-man(10), starLan(11), proteon-10Mbit(12), proteon-80Mbit(13), hyperchannel(14), fddi(15), lapb(16), sdlc(17), ds1(18), cept(19), basicISDN(20), primaryISDN(21), propPointToPointSerial(22), ppp(23), loopback(24), eon(25), ethernet-3Mbit(26), nsip(27), slip(28), ultra(29), ds3(30), sip(31), frame-relay(32)  

ibmvNbrRemAddress 1.3.6.1.4.1.2.6.2.18.3.3.1.5
The address of the neighbor's physical interface. For LAN's, it is the hardware address of the neighbor.
OBJECT-TYPE    
  OCTET STRING  

ibmvNbrLocAddress 1.3.6.1.4.1.2.6.2.18.3.3.1.6
The address of the router node's physical interface, such as a LAN address.
OBJECT-TYPE    
  OCTET STRING  

ibmvNbrLocSlot 1.3.6.1.4.1.2.6.2.18.3.3.1.7
The slot number of the interface card that the router node uses to reach the neighbor.
OBJECT-TYPE    
  INTEGER 1..7  

ibmvNbrLocPort 1.3.6.1.4.1.2.6.2.18.3.3.1.8
The port number on the interface card that the router node used to reach the neighbor.
OBJECT-TYPE    
  INTEGER 0..3  

ibmvNbrAging 1.3.6.1.4.1.2.6.2.18.3.3.1.9
The amount of time left before a neighbor entry will be removed because of aging. For a WAN link, which is defined to be permanent, this object is not applicable.
OBJECT-TYPE    
  INTEGER  

ibmvNbrFlags 1.3.6.1.4.1.2.6.2.18.3.3.1.10
Only applicable to a WAN link; states if the link is permanent or non-permanent.
OBJECT-TYPE    
  INTEGER permanent(1), nonpermanent(2)  

ibmvNbrRIF 1.3.6.1.4.1.2.6.2.18.3.3.1.11
LAN - MAC address and if applicable, source routing information. Frame Relay - n/a PPP - n/a
OBJECT-TYPE    
  OCTET STRING  

ibmvNbrIfIndex 1.3.6.1.4.1.2.6.2.18.3.3.1.12
The interface (using the MIB II standard) used to reach the neighbor. This number corresponds to the IfIndex object found in MIB II.
OBJECT-TYPE    
  INTEGER  

ibmvNbrMetric 1.3.6.1.4.1.2.6.2.18.3.3.1.13
The cost to reach the neighbor.
OBJECT-TYPE    
  INTEGER  

ibmvRouting 1.3.6.1.4.1.2.6.2.18.4
OBJECT IDENTIFIER    

ibmvRtConfig 1.3.6.1.4.1.2.6.2.18.4.1
OBJECT IDENTIFIER    

ibmvRtCfgMax 1.3.6.1.4.1.2.6.2.18.4.1.1
The maximum number of entries allowed in the routing table. This value is not defined by administrator.
OBJECT-TYPE    
  INTEGER  

ibmvRtCfgInFlt 1.3.6.1.4.1.2.6.2.18.4.1.2
Enables or disables all inbound RTP filters defined. If no inbound RTP filters are defined, then this object has no effect. If a filter is defined, then the default value is 'enabled'.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ibmvRtCfgInFltNum 1.3.6.1.4.1.2.6.2.18.4.1.3
The number of inbound RTP filters currently defined.
OBJECT-TYPE    
  INTEGER  

ibmvRtCfgInFltTable 1.3.6.1.4.1.2.6.2.18.4.1.4
A list of information about the inbound RTP filters which are specified for this router node.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmvRtCfgInFltEntry

ibmvRtCfgInFltEntry 1.3.6.1.4.1.2.6.2.18.4.1.4.1
The information for each entry in the inbound RTP filter table.
OBJECT-TYPE    
  IbmvRtCfgInFltEntry  

ibmvRtCfgInFltNetID 1.3.6.1.4.1.2.6.2.18.4.1.4.1.1
Administrator defined object which specifies the VINES network number to be filtered on the port. The range of the network number is 00000000 - FFFFFFFE. If the network number, 0xFFFFFFFF, is defined, then all network numbers will be filtered.
OBJECT-TYPE    
  OCTET STRING  

ibmvRtCfgInFltIfIndex 1.3.6.1.4.1.2.6.2.18.4.1.4.1.2
The interface (using the MIB II standard) for which the inbound RTP filters were defined. This number corresponds to the IfIndex object found in MIB II.
OBJECT-TYPE    
  INTEGER  

ibmvRtCfgInFltMode 1.3.6.1.4.1.2.6.2.18.4.1.4.1.3
The filtering action for the inbound RTP filter. The inbound RTP filters operate on network numbers contained in the topological entries in the RTP update, response, and redirect packets received over a specified interface. In deny mode, the 6611 ignores route information for a network if the network number and the port on which the route information was received matches any inbound RTP filter. In permit mode, the IBM 6611 processes route information for a network only if the network number and the port on which the route information was received matches any inbound RTP filter. The default for this object is 'deny'.
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

ibmvRtCfgInFltUses 1.3.6.1.4.1.2.6.2.18.4.1.4.1.4
The number of times the defined filter was used.
OBJECT-TYPE    
  Counter  

ibmvRtCfgOutFlt 1.3.6.1.4.1.2.6.2.18.4.1.5
Enables or disables all outbound RTP filters defined. If no outbound RTP filters are defined, then this object has no effect. If a filter is defined, then the default value is 'enabled'.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ibmvRtCfgOutFltNum 1.3.6.1.4.1.2.6.2.18.4.1.6
The number of outbound RTP filters currently defined.
OBJECT-TYPE    
  INTEGER  

ibmvRtCfgOutFltTable 1.3.6.1.4.1.2.6.2.18.4.1.7
A list of information about the outbound RTP filters which are specified for this router node.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmvRtCfgOutFltEntry

ibmvRtCfgOutFltEntry 1.3.6.1.4.1.2.6.2.18.4.1.7.1
The information for each entry in the outbound RTP filter table.
OBJECT-TYPE    
  IbmvRtCfgOutFltEntry  

ibmvRtCfgOutFltNetID 1.3.6.1.4.1.2.6.2.18.4.1.7.1.1
Administrator defined object which specifies the VINES network number to be filtered on the port. The range of the network number is 00000000 - FFFFFFFE. If the network number, 0xFFFFFFFF, is defined, then all network numbers will be filtered.
OBJECT-TYPE    
  OCTET STRING  

ibmvRtCfgOutFltIfIndex 1.3.6.1.4.1.2.6.2.18.4.1.7.1.2
The interface (using the MIB II standard) for which the outbound RTP filters were defined. This number corresponds to the IfIndex object found in MIB II.
OBJECT-TYPE    
  INTEGER  

ibmvRtCfgOutFltMode 1.3.6.1.4.1.2.6.2.18.4.1.7.1.3
The filtering action for the outbound RTP filter. The outbound RTP filters operate on the network numbers contained in the topological entries in RTP update and response packets transmitted over a specified interface. In deny mode, filters operate on interface names and network numbers (that is, the network numbers contained in the topological entries in the RTP packets). In deny mode, the IBM 6611 does not advertise route information for a network if the network number and the interface on which the route information is to be transmitted matches any outbound RTP filter. In permit mode, the 6611 advertises route information for a network only if the network number and the interface on which the route information is to be transmitted matches any outbound RTP filter. The default for this object is 'Deny'.
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

ibmvRtCfgOutFltUses 1.3.6.1.4.1.2.6.2.18.4.1.7.1.4
The number of times the defined filter was used.
OBJECT-TYPE    
  Counter  

ibmvRtCfgFlt 1.3.6.1.4.1.2.6.2.18.4.1.8
Enables or disables all RTP router filters defined. If no RTP router filters are defined, then this object has no effect. If a filter is defined, then the default value is 'enabled'.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ibmvRtCfgFltNum 1.3.6.1.4.1.2.6.2.18.4.1.9
The number of RTP router filters currently defined.
OBJECT-TYPE    
  INTEGER  

ibmvRtCfgFltTable 1.3.6.1.4.1.2.6.2.18.4.1.10
A list of information about the RTP router filters which are specified for this router node.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmvRtCfgFltEntry

ibmvRtCfgFltEntry 1.3.6.1.4.1.2.6.2.18.4.1.10.1
The information for each entry in the RTP router filter table.
OBJECT-TYPE    
  IbmvRtCfgFltEntry  

ibmvRtCfgFltNetID 1.3.6.1.4.1.2.6.2.18.4.1.10.1.1
Administrator defined object which specifies the VINES network number to be filtered on the port. The range of the network number is 00000000 - FFFFFFFE. If the network number, 0xFFFFFFFF, is defined, then all network numbers will be filtered.
OBJECT-TYPE    
  OCTET STRING  

ibmvRtCfgFltMode 1.3.6.1.4.1.2.6.2.18.4.1.10.1.2
The filtering action for the RTP router filter. The RTP router filters operate on the network number contained in the source network number field in the IP header of any RTP packet (update, request, response, and redirect). (The subnetwork ID is assumed to be 0x0001.) In deny mode, the IBM 6611 ignores route information from a service node if the sending router's network number matches any RTP router filter. In permit mode, the IBM 6611 processes route information from a router only if the sending router's network number matches any RTP router filter. The default for this object is 'deny'.
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

ibmvRtCfgFltUses 1.3.6.1.4.1.2.6.2.18.4.1.10.1.3
The number of times the defined filter was used.
OBJECT-TYPE    
  Counter  

ibmvRTP 1.3.6.1.4.1.2.6.2.18.4.2
OBJECT IDENTIFIER    

ibmvrtpUpdSents 1.3.6.1.4.1.2.6.2.18.4.2.1
The number of routing update packets sent since the last reboot. The routing update packets are periodically broadcast by nodes to notify neighboring nodes of their existence. Router nodes include network topology information in these updates.
OBJECT-TYPE    
  Counter  

ibmvrtpUpdRecs 1.3.6.1.4.1.2.6.2.18.4.2.2
The number of routing update packets received since the last reboot. The routing update packets are sent from neighboring node making known their existence. Packets received from router nodes include network topology information.
OBJECT-TYPE    
  Counter  

ibmvrtpReqSents 1.3.6.1.4.1.2.6.2.18.4.2.3
The number of routing request packets sent since the last reboot. Routing request packets are sent by a node when it requires an immediate update.
OBJECT-TYPE    
  Counter  

ibmvrtpReqRecs 1.3.6.1.4.1.2.6.2.18.4.2.4
The number of routing request packets received since the last reboot. The 6611 receives routing request packets when another node requires an immediate update. The 6611 will send the update in a routing response packet.
OBJECT-TYPE    
  Counter  

ibmvrtpResSents 1.3.6.1.4.1.2.6.2.18.4.2.5
The number of routing response packets sent since the last reboot. Routing response packets are sent in response to a routing request packet.
OBJECT-TYPE    
  Counter  

ibmvrtpResRecs 1.3.6.1.4.1.2.6.2.18.4.2.6
The number of routing response packets received since the last reboot. When a node sends out a routing request packet, it receives a routing response packet which contains all the routing information requested.
OBJECT-TYPE    
  Counter  

ibmvrtpRedSents 1.3.6.1.4.1.2.6.2.18.4.2.7
The number of routing redirect packets sent since the last reboot. The routing redirect packets are sent by a node to notify another node of a more direct path to a destination node.
OBJECT-TYPE    
  Counter  

ibmvrtpRedRecs 1.3.6.1.4.1.2.6.2.18.4.2.8
The number of routing redirect packets received since the last reboot. A 6611 receives a routing redirect packet when another node knows a more direct path to the destination node.
OBJECT-TYPE    
  Counter  

ibmvrtpHeaderError 1.3.6.1.4.1.2.6.2.18.4.2.9
The number of RTP packets received since the last reboot with a RTP header error.
OBJECT-TYPE    
  Counter  

ibmvRtNumber 1.3.6.1.4.1.2.6.2.18.4.3
The number of entires in the route table.
OBJECT-TYPE    
  INTEGER  

ibmvRtTable 1.3.6.1.4.1.2.6.2.18.4.4
A list of information about IBM's VINES router table.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmvRtEntry

ibmvRtEntry 1.3.6.1.4.1.2.6.2.18.4.4.1
The information for each entry in the router table.
OBJECT-TYPE    
  IbmvRtEntry  

ibmvRtNetid 1.3.6.1.4.1.2.6.2.18.4.4.1.1
The network ID of the router node's destination router node.
OBJECT-TYPE    
  OCTET STRING  

ibmvRtMetric 1.3.6.1.4.1.2.6.2.18.4.4.1.2
The routing metric used by the called router node to reach the destination. A routing metric is an estimated round-trip delay time associated with the router that maximum sized VINES IP packets will take to reach the destination. The metric reflects the cost of the path to the destination, it is in 200-millisecond units.
OBJECT-TYPE    
  INTEGER  

ibmvRtIdle 1.3.6.1.4.1.2.6.2.18.4.4.1.3
The time to live timer for this router node's entry. This value indicates the amount of time before the entry is removed from the called router node's routing table. The value is returned in 90 second units.
OBJECT-TYPE    
  INTEGER  

ibmvRtGateNetid 1.3.6.1.4.1.2.6.2.18.4.4.1.4
The network ID of the router node that acts as the router for reaching the destination router node.
OBJECT-TYPE    
  OCTET STRING  

ibmvRtIfIndex 1.3.6.1.4.1.2.6.2.18.4.4.1.5
The interface (using the MIB II standard) which identifies the local interface through which the next hop of this route should be reached. This number corresponds to the IfIndex object found in MIB II.
OBJECT-TYPE    
  INTEGER  

ibmvRtState 1.3.6.1.4.1.2.6.2.18.4.4.1.6
The state the routing entry; permanent or not permanent.
OBJECT-TYPE    
  INTEGER permanent(1), nonpermanent(2)  

ibmvICP 1.3.6.1.4.1.2.6.2.18.5
OBJECT IDENTIFIER    

ibmvicpExcGens 1.3.6.1.4.1.2.6.2.18.5.1
Number of exception notifications generated from this router node since the last reboot.
OBJECT-TYPE    
  Counter  

ibmvicpMetricGens 1.3.6.1.4.1.2.6.2.18.5.2
The number of metric notifications generated from this router node since the last reboot. The ICP packet contains metric information about the final transmission medium used to reach a client node.
OBJECT-TYPE    
  Counter  

ibmvicpHeaderError 1.3.6.1.4.1.2.6.2.18.5.3
The number of ICP packets received since the last reboot with an ICP header error.
OBJECT-TYPE    
  Counter  

ibmvFRP 1.3.6.1.4.1.2.6.2.18.6
OBJECT IDENTIFIER    

ibmvFRPreassembles 1.3.6.1.4.1.2.6.2.18.6.1
The number of times packets were reassembled since the last reboot. One VINES IP packet being broken into three message fragments is counted as one fragmentation. The three fragments being reassembled into one VINES IP packet counts as one reassembly.
OBJECT-TYPE    
  Counter  

ibmvFRPfragsReassembled 1.3.6.1.4.1.2.6.2.18.6.2
The number of fragments that were reassembled since the last reboot. If three fragments are to be reassembled into one packet, then this object value will add three to its total.
OBJECT-TYPE    
  Counter  

ibmvFRPreasFails 1.3.6.1.4.1.2.6.2.18.6.3
The number of times the reassembly of fragments fails since the last reboot.
OBJECT-TYPE    
  Counter  

ibmvFRPfragmented 1.3.6.1.4.1.2.6.2.18.6.4
The number of packet fragmentations performed since the last reboot.
OBJECT-TYPE    
  Counter  

ibmvFRPfrgCreated 1.3.6.1.4.1.2.6.2.18.6.5
The number of fragments created since the last reboot when fragmenting VINES IP packets. If a VINES IP packet is fragmented into three fragments, then this object value will add three to its total.
OBJECT-TYPE    
  Counter  

ibmvFRPfrgFails 1.3.6.1.4.1.2.6.2.18.6.6
The number of times the fragmentation of a VINES IP packets fails since the last reboot.
OBJECT-TYPE    
  Counter  

ibmvInterface 1.3.6.1.4.1.2.6.2.18.7
OBJECT IDENTIFIER    

ibmvPortCfgTable 1.3.6.1.4.1.2.6.2.18.7.1
The list of information about port configuration at each interface.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmvPortCfgEntry

ibmvPortCfgEntry 1.3.6.1.4.1.2.6.2.18.7.1.1
The information for each entry in the port configuration table.
OBJECT-TYPE    
  IbmvPortCfgEntry  

ibmvPortCfgIfIndex 1.3.6.1.4.1.2.6.2.18.7.1.1.1
The interface (using the MIB II standard) which uniquely identifies each interface and allows multiple tables to be associated with a given interface. This number corresponds to the IfIndex object found in MIB II.
OBJECT-TYPE    
  INTEGER  

ibmvPortCfgARP 1.3.6.1.4.1.2.6.2.18.7.1.1.2
Administrator defined value which specifies whether the router node will assign VINES addresses to clients that reside on the LAN attached to this port. The default value for this object is 'disable'.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ibmvPortCfgServ 1.3.6.1.4.1.2.6.2.18.7.1.1.3
Administrator defined value specifying whether the serverless option is enables or disabled. When the serverless option is enabled; the router looks for particular broadcasts that clients use in finding the services on the VINES server. This allows client nodes on a serverless LAN to communicate with a VINES server more than one hop away. The default value for this object is 'disable'.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ibmvPortCfgHCtoServ 1.3.6.1.4.1.2.6.2.18.7.1.1.4
Administrator defined value which specifies the number of hops from the client to the router node.
OBJECT-TYPE    
  INTEGER  

ibmvPortCfgPerUpdate 1.3.6.1.4.1.2.6.2.18.7.1.1.5
Administrator defined value which specifies whether periodic updates will be sent over a WAN link.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), na(3)  

ibmvPortCfgMetric 1.3.6.1.4.1.2.6.2.18.7.1.1.6
Administrator defined value for port metric. This value overrides the metric which is used by the IBM 6611 to make routing decisions. If no response is provided to this parameter, the IBM 6611 will use defaults contained within the MPNP program. These defaults are based on values assigned by Banyan Systems for its VINES servers. The port metric is a rough estimate of the round trip delay for a maximum sized VINES IP packet to travel to any neighbor on this port. The unit for the metric value is 200 milliseconds. The default metric for an Ethernet port is 2. The default metric for a Token-Ring is determined by the response to the Token-Ring Data Rate parameter. The default metric for a serial port is determined by the response to the Serial-Line Speed parameter.
OBJECT-TYPE    
  INTEGER  

ibmvPortCfgTR 1.3.6.1.4.1.2.6.2.18.7.1.1.7
Administrator defined value which determines the encapsulation method used for receiving and transmitting VINES packets on this port. IEEE 802.5 LLC uses 802.2 encapsulation followed by an LLC field using SAP value 0xBC You cannot use IEEE 802.5 LLC encapsulation on the same port that performs data link switching, if the 0xBC SAP has been configured for frame forwarding by the data link switching function. IEEE 802.5 SNAP uses 802.2 encapsulation followed by a SNAP header using the organizationally unique ID 0x08 00 4A, the protocol id 0x80C4 for VINES IP and the protocol id 0x80C5 for VINES Link Level Echo.
OBJECT-TYPE    
  INTEGER na(1), snap(2), vines-tr(3)  

ibmvPortCfgEN 1.3.6.1.4.1.2.6.2.18.7.1.1.8
Administrator defined value which determines the encapsulation method used for receiving and transmitting VINES packets on this port. Ethernet II uses DIX encapsulation with a packet type 0x0BAD for VINES IP and 0x0BAF for VINES Link Level Echo. IEEE 802.3 SNAP uses 802.2 encapsulation followed by a SNAP header using the organizationally unique ID 0x08 00 4A, the protocol id 0x80C4 for VINES IP and the protocol id 0x80C5 for VINES Link Level Echo.
OBJECT-TYPE    
  INTEGER na(1), snap(2), v2(3)  

ibmvPortCfgInFlt 1.3.6.1.4.1.2.6.2.18.7.1.1.9
Administrator defined value which allows inbound port filters to be defined. The default value is 'disabled'.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ibmvPortCfgInFltNum 1.3.6.1.4.1.2.6.2.18.7.1.1.10
The number of inbound port filters defined for this port.
OBJECT-TYPE    
  INTEGER  

ibmvPortCfgOutFlt 1.3.6.1.4.1.2.6.2.18.7.1.1.11
Administrator defined value which allows outbound port filters to be defined. The default value is 'disabled'.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ibmvPortCfgOutFltNum 1.3.6.1.4.1.2.6.2.18.7.1.1.12
The number of outbound port filters defined for this port.
OBJECT-TYPE    
  INTEGER  

ibmvFltTable 1.3.6.1.4.1.2.6.2.18.7.2
The list of information about port filter configurations at each interface .
OBJECT-TYPE    
  SEQUENCE OF  
    IbmvFltEntry

ibmvFltEntry 1.3.6.1.4.1.2.6.2.18.7.2.1
The information for each entry in the port filter configuration table.
OBJECT-TYPE    
  IbmvFltEntry  

ibmvFltIfIndex 1.3.6.1.4.1.2.6.2.18.7.2.1.1
The value of this object identifies the interface for which this entry contains management information. The IfIndex allows a subset of the filter table to be associated with a particular interface.
OBJECT-TYPE    
  INTEGER  

ibmvFltNo 1.3.6.1.4.1.2.6.2.18.7.2.1.2
A unique integer identifying this filter entry for this interface.
OBJECT-TYPE    
  INTEGER  

ibmvFltMode 1.3.6.1.4.1.2.6.2.18.7.2.1.3
Identifies if the port filter is an inbound or outbound filter.
OBJECT-TYPE    
  INTEGER inbound(1), outbound(2)  

ibmvFltValue 1.3.6.1.4.1.2.6.2.18.7.2.1.4
An octet string representing the concatenation of VINES IP header fields and VINES transport header fields required by this filter entry. Incoming packets will be bitwise ANDed with the value of ibmvFltMask, and if the result is equal to the value of this object, the packet will be filtered according to the value of ibmvFltValue. Fields from VINES IP and transport headers used for filtering: field length field name ------------ ------------------------------ 8 BITS protocol type 4 BITS hop count 32 BITS destination network number 16 BITS destination subnetwork number 16 BITS destination port number 32 BITS source network number 16 BITS source subnetwork number 16 BITS source port number
OBJECT-TYPE    
  OCTET STRING SIZE(18)  

ibmvFltMask 1.3.6.1.4.1.2.6.2.18.7.2.1.5
An octet string indicating the parts of the VIP header and transport header relevant to this filter entry. This mask will be bitwise ANDed with the appropriate header fields; if the result is equal to the value of ibmvnFilterValue, the packet will be filtered according to the value of ibmvnFilterType.
OBJECT-TYPE    
  OCTET STRING SIZE(18)  

ibmvFltType 1.3.6.1.4.1.2.6.2.18.7.2.1.6
Administrator defined value which determines the filtering mode for all filters defined on this port. If the port is using Deny mode, then all packets matching a defined port filter will be discarded. If the port is using Permit mode, then only the packets matching a defined port filter will be forwarded. The default value is Deny.
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

ibmvFltHCCompare 1.3.6.1.4.1.2.6.2.18.7.2.1.7
Administrator defined value which indicates the relational association desired if filtering is being done based on hop count. If filtering is not being done based on hop count (that is, if the hop count portion of IBM VINES Port Mask is 0) the value of this object will be none(1).
OBJECT-TYPE    
  INTEGER less-than(1), less-than-equal(2), equal(3), greater-than-equal(4), greater-than(5), na(6)  

ibmvFltUses 1.3.6.1.4.1.2.6.2.18.7.2.1.8
This object counts how many times the defined filter was used.
OBJECT-TYPE    
  Counter  

ibmvifNumber 1.3.6.1.4.1.2.6.2.18.7.3
The number of VINES interfaces configured on the router node.
OBJECT-TYPE    
  INTEGER  

ibmvifTable 1.3.6.1.4.1.2.6.2.18.7.4
List of interfaces with some statistics about each interface.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmvifEntry

ibmvifEntry 1.3.6.1.4.1.2.6.2.18.7.4.1
Information about one interface.
OBJECT-TYPE    
  IbmvifEntry  

ibmvifSlot 1.3.6.1.4.1.2.6.2.18.7.4.1.1
The slot number of the interface's communications card.
OBJECT-TYPE    
  INTEGER 1..7  

ibmvifPort 1.3.6.1.4.1.2.6.2.18.7.4.1.2
The port number of the interface.
OBJECT-TYPE    
  INTEGER 0..3  

ibmvifDescr 1.3.6.1.4.1.2.6.2.18.7.4.1.3
A textual description of the interface.
OBJECT-TYPE    
  DisplayString  

ibmvifAddress 1.3.6.1.4.1.2.6.2.18.7.4.1.4
The physical address of the interface, applies to LAN interfaces only.
OBJECT-TYPE    
  OCTET STRING  

ibmvifInPkts 1.3.6.1.4.1.2.6.2.18.7.4.1.5
The total number of VINES IP packets that the router node received since the last reboot.
OBJECT-TYPE    
  Counter  

ibmvifInErrs 1.3.6.1.4.1.2.6.2.18.7.4.1.6
The total number of received VINES IP packets that contained errors since the last reboot.
OBJECT-TYPE    
  Counter  

ibmvifOutPkts 1.3.6.1.4.1.2.6.2.18.7.4.1.7
The total number of VINES IP packets that the router node sent since the last reboot.
OBJECT-TYPE    
  Counter  

ibmvifOutErrs 1.3.6.1.4.1.2.6.2.18.7.4.1.8
The total number of transmitted VINES IP packets that contained errors since the last reboot.
OBJECT-TYPE    
  Counter  

ibminterfaces 1.3.6.1.4.1.2.6.2.19
OBJECT IDENTIFIER    

ibmipext 1.3.6.1.4.1.2.6.2.19.1
OBJECT IDENTIFIER    

ibmipPtyQueueEnableTable 1.3.6.1.4.1.2.6.2.19.1.1
This table defines which interfaces are enabled for IP prioritization. It also defines the default serial transmission priority queue to be used for IP packets which are not assigned to use a specific transmission queue.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmipPtyQueueEnableEntry

ibmipPtyQueueEnableEntry 1.3.6.1.4.1.2.6.2.19.1.1.1
Each entry defines whether IP prioritization is enabled on a particular interface and the default transmission queue.
OBJECT-TYPE    
  IbmipPtyQueueEnableEntry  

ibmipPtyQueueEnableIfIndex 1.3.6.1.4.1.2.6.2.19.1.1.1.1
Defines the interface associated with IP prioritization. This interface is the same interface as defined by the ifIndex variable of the MIB-II interfaces group.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmipPtyQueueEnable 1.3.6.1.4.1.2.6.2.19.1.1.1.2
The value of this object identifies if IP prioritization is enabled on this interface.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ibmipPtyQueueDefault 1.3.6.1.4.1.2.6.2.19.1.1.1.3
Identifies the transmission queue to be used for IP packets which are not assigned to use a specific transmission queue.
OBJECT-TYPE    
  INTEGER high(1), medium(2), low(3)  

ibmipPtyQueueTable 1.3.6.1.4.1.2.6.2.19.1.2
This table contains the assignments of UDP/TCP port numbers to specific transmission queues for a given serial interface.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmipPtyQueueEntry

ibmipPtyQueueEntry 1.3.6.1.4.1.2.6.2.19.1.2.1
Each entry defines the UDP/TCP port number and its associated transmission priority queue for a given interface.
OBJECT-TYPE    
  IbmipPtyQueueEntry  

ibmipPtyQueueIfIndex 1.3.6.1.4.1.2.6.2.19.1.2.1.1
Defines the interface on which a UDP/TCP port is associated with a specific transmission priority queue. This interface is the same interface as defined by the ifIndex variable of the MIB-II interfaces group.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmipPtyQueuePort 1.3.6.1.4.1.2.6.2.19.1.2.1.2
Identifies a UDP or TCP port number.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmipPtyQueueType 1.3.6.1.4.1.2.6.2.19.1.2.1.3
Indicates the port type of the port number defined by ibmipPtyQueuePort.
OBJECT-TYPE    
  INTEGER tcp(1), udp(2)  

ibmipPtyQueueNumber 1.3.6.1.4.1.2.6.2.19.1.2.1.4
Indicates which transmission queue will be used to transmit a packet which has a port number as specified by ibmipPtyQueuePort.
OBJECT-TYPE    
  INTEGER high(1), medium(2), low(3)  

ibmipFilterTable 1.3.6.1.4.1.2.6.2.19.1.3
Table of IP address/mask filter definitions.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmipFilterEntry

ibmipFilterEntry 1.3.6.1.4.1.2.6.2.19.1.3.1
An entry in the IP address/mask filter table.
OBJECT-TYPE    
  IbmipFilterEntry  

ibmipFilterIfIndex 1.3.6.1.4.1.2.6.2.19.1.3.1.1
Defines the interface associated with this address/mask filter definition. This interface is the same interface as defined by the ifIndex variable of the MIB-II interfaces group.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmipFilterId 1.3.6.1.4.1.2.6.2.19.1.3.1.2
An id that defines this filter entry. This number is unique within this interface.
OBJECT-TYPE    
  INTEGER 1..50  

ibmipFilterScope 1.3.6.1.4.1.2.6.2.19.1.3.1.3
Defines whether this filter is applied to all interfaces or just this one.
OBJECT-TYPE    
  INTEGER system(1), interface(2)  

ibmipFilterType 1.3.6.1.4.1.2.6.2.19.1.3.1.4
Defines the type of filtering.
OBJECT-TYPE    
  INTEGER singular(1), dual(2)  

ibmipPermitDeny 1.3.6.1.4.1.2.6.2.19.1.3.1.5
Identifies whether traffic for a specified filter ID is to be permitted to pass through the IBM 6611 or whether it is to be discarded.
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

ibmipFilterAddr1 1.3.6.1.4.1.2.6.2.19.1.3.1.6
A valid IP address of the host, subnet or network for this filter. For singular filters, this is the only end point, however, for dual filters this is the source end point.
OBJECT-TYPE    
  IpAddress  

ibmipFilterMask1 1.3.6.1.4.1.2.6.2.19.1.3.1.7
A valid IP address mask used for this filter. In conjunction with the IP address defined by ibmipFilterAddr1, it defines the range of IP addresses to be filtered.
OBJECT-TYPE    
  IpAddress  

ibmipFilterAddr2 1.3.6.1.4.1.2.6.2.19.1.3.1.8
Defines the destination IP address if ibmipFilterType is dual. This value is undefined for singular filters.
OBJECT-TYPE    
  IpAddress  

ibmipFilterMask2 1.3.6.1.4.1.2.6.2.19.1.3.1.9
A valid IP address mask used for this filter. In conjunction with the IP address defined by ibmipFilterAddr2, it defines the range of IP addresses to be filtered.
OBJECT-TYPE    
  IpAddress  

ibmipFilterExtTable 1.3.6.1.4.1.2.6.2.19.1.4
Table of IP port number filter definitions.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmipFilterExtEntry

ibmipFilterExtEntry 1.3.6.1.4.1.2.6.2.19.1.4.1
An entry in the IP port number filter table.
OBJECT-TYPE    
  IbmipFilterExtEntry  

ibmipFilterExtIfIndex 1.3.6.1.4.1.2.6.2.19.1.4.1.1
Defines the interface associated with this IP port number filter definition. This interface is the same interface as defined by the ifIndex variable of the MIB-II interfaces group.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmipFilterExtFilterId 1.3.6.1.4.1.2.6.2.19.1.4.1.2
An id that defines this filter entry. This number is unique within this interface and is the same filter ID as defined by ibmipFilterId.
OBJECT-TYPE    
  INTEGER 1..50  

ibmipFilterExtValue 1.3.6.1.4.1.2.6.2.19.1.4.1.3
Defines a TCP or UDP port number that will be filtered using this filter specification.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmipFilterExtProtocol 1.3.6.1.4.1.2.6.2.19.1.4.1.4
Specifies the protocol associated with the value defined by ibmipFilterExtValue for this filter specification.
OBJECT-TYPE    
  INTEGER none(0), tcpudp(1)  

ibmptyqueue 1.3.6.1.4.1.2.6.2.19.2
OBJECT IDENTIFIER    

ibmPtyQueueingTable 1.3.6.1.4.1.2.6.2.19.2.1
This table provides information on a specific transmission queue of a serial interface. Information includes: - Link Bandwidth Allocation (LBA): Identifies the number of packets transmitted from a particular queue before a lower priority transmission queue will be serviced. - Queue Bandwidth Reservation (QBR): Identifies the percentage of buffer space on a serial adapter that is allotted to a particular queue for transmission of packets.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmPtyQueueingEntry

ibmPtyQueueingEntry 1.3.6.1.4.1.2.6.2.19.2.1.1
Each entry defines the Link Bandwidth Allocation (LBA) and Queue Bandwidth Reservation (QBR) definitions for a specific transmission queue on a serial interface. Additionally, a counter is provided indicating the number of packets discarded on this queue due to a queue overflow.
OBJECT-TYPE    
  IbmPtyQueueingEntry  

ibmPtyQueueingIfIndex 1.3.6.1.4.1.2.6.2.19.2.1.1.1
Defines the interface associated with this priority queue information. This interface is the same interface as defined by the ifIndex variable of the MIB-II interfaces group.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmPtyQueueingQnum 1.3.6.1.4.1.2.6.2.19.2.1.1.2
Identifies the priority queue associated with this interface and its priority queue information.
OBJECT-TYPE    
  INTEGER high(1), medium(2), low(3)  

ibmPtyQueueingLBA 1.3.6.1.4.1.2.6.2.19.2.1.1.3
Link Bandwidth Allocation (LBA): Identifies the number of packets that will be transmitted from this queue before a lower priority queue will be serviced.
OBJECT-TYPE    
  INTEGER 1..10  

ibmPtyQueueingQBR 1.3.6.1.4.1.2.6.2.19.2.1.1.4
Queue Bandwidth Reservation (QBR): Identifies the percentage of buffer space on a serial adapter that is allotted to a particular queue for transmission of packets. The sum of all QBR values on an interface must add up to 100%.
OBJECT-TYPE    
  INTEGER  

ibmPtyQueueingDiscards 1.3.6.1.4.1.2.6.2.19.2.1.1.5
Identifies the number of packets discarded from this queue due to a queue overflow.
OBJECT-TYPE    
  Counter  

ibmTG 1.3.6.1.4.1.2.6.2.19.3
OBJECT IDENTIFIER    

ibmTGTable 1.3.6.1.4.1.2.6.2.19.3.1
This table provides information about serial point-to-point links which are participating in the 2 T1 in a transmission group (TG) function.
OBJECT-TYPE    
  SEQUENCE OF  
    IbmTGEntry

ibmTGEntry 1.3.6.1.4.1.2.6.2.19.3.1.1
Each entry identifies an interface participating in the 2 T1 in a TG function, along with its associated TG name and which protocol is using the function.
OBJECT-TYPE    
  IbmTGEntry  

ibmTGProtocol 1.3.6.1.4.1.2.6.2.19.3.1.1.1
Defines the protocol that is supported for this particular interface and TG name. Currently, only the IP protocol is supported
OBJECT-TYPE    
  INTEGER ip(2048)  

ibmTGIfIndex 1.3.6.1.4.1.2.6.2.19.3.1.1.2
Defines the interface associated with this particular TG name and protocol. This interface is the same interface as defined by the ifIndex variable of the MIB-II interfaces group.
OBJECT-TYPE    
  INTEGER 0..65535  

ibmTGEnable 1.3.6.1.4.1.2.6.2.19.3.1.1.3
Defines whether the 2 T1 in a TG function is enabled on this interface
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ibmTGGroupName 1.3.6.1.4.1.2.6.2.19.3.1.1.4
Defines the common TG name assigned to all interfaces in this group. All interfaces with the same TG name will belong to the same group.
OBJECT-TYPE    
  DisplayString SIZE(1..8)  

ibmTGSwitchOuts 1.3.6.1.4.1.2.6.2.19.3.1.1.5
Counts the number of times a packet had to be switched to another interface in the transmission group.
OBJECT-TYPE    
  Counter  

Defined Objects

IbmMainProcessorLoadEntry  
SEQUENCE    
  INTEGER as ibmMainProcessorLoadIndex  
  Gauge as ibmMainProcessorLoad  

SwVpdEntry  
SEQUENCE    
  INTEGER as swvpdIndex  
  DisplayString as swvpdName  
  DisplayString as swvpdPtfName  
  INTEGER as swvpdVerId  
  INTEGER as swvpdRelId  
  INTEGER as swvpdModId  
  INTEGER as swvpdFixId  
  INTEGER as swvpdState  
  INTEGER as swvpdAction  
  INTEGER as swvpdPath  
  DisplayString as swvpdDateTime  

MacAddrFilterInfoEntry  
SEQUENCE    
  INTEGER as ibmmacAddrFilterIfIndex  
  INTEGER as ibmmacAddrFilterInBcastType  
  INTEGER as ibmmacAddrFilterOutBcastType  
  INTEGER as ibmmacAddrFilterInFilterType  
  INTEGER as ibmmacAddrFilterOutFilterType  
  Counter as ibmmacAddrFilterInNotForwarded  
  Counter as ibmmacAddrFilterOutNotForwarded  
  INTEGER as ibmmacAddrFilterType  

MacAddrFilterInEntry  
SEQUENCE    
  INTEGER as ibmmacAddrFilterInIfIndex  
  OCTET STRING as ibmmacAddrFilterInSrcAddress  
  OCTET STRING as ibmmacAddrFilterInSrcMask  
  OCTET STRING as ibmmacAddrFilterInDestAddress  
  OCTET STRING as ibmmacAddrFilterInDestMask  
  INTEGER as ibmmacAddrFilterInType  

MacAddrFilterOutEntry  
SEQUENCE    
  INTEGER as ibmmacAddrFilterOutIfIndex  
  OCTET STRING as ibmmacAddrFilterOutSrcAddress  
  OCTET STRING as ibmmacAddrFilterOutSrcMask  
  OCTET STRING as ibmmacAddrFilterOutDestAddress  
  OCTET STRING as ibmmacAddrFilterOutDestMask  
  INTEGER as ibmmacAddrFilterOutType  

SapFilterInfoEntry  
SEQUENCE    
  INTEGER as ibmsapFilterIfIndex  
  INTEGER as ibmsapFilterInBcastType  
  INTEGER as ibmsapFilterOutBcastType  
  OCTET STRING as ibmsapFilterIn  
  OCTET STRING as ibmsapFilterOut  
  Counter as ibmsapFilterInNotForwarded  
  Counter as ibmsapFilterOutNotForwarded  
  INTEGER as ibmsapFilterType  

SnapFilterInfoEntry  
SEQUENCE    
  INTEGER as ibmsnapFilterIfIndex  
  INTEGER as ibmsnapFilterInFilterType  
  INTEGER as ibmsnapFilterOutFilterType  
  Counter as ibmsnapFilterInNotForwarded  
  Counter as ibmsnapFilterOutNotForwarded  
  INTEGER as ibmsnapFilterType  

SnapFilterInEntry  
SEQUENCE    
  INTEGER as ibmsnapFilterInIfIndex  
  INTEGER as ibmsnapFilterInValue  
  INTEGER as ibmsnapFilterInMask  
  INTEGER as ibmsnapFilterInType  

SnapFilterOutEntry  
SEQUENCE    
  INTEGER as ibmsnapFilterOutIfIndex  
  INTEGER as ibmsnapFilterOutValue  
  INTEGER as ibmsnapFilterOutMask  
  INTEGER as ibmsnapFilterOutType  

RingFilterInfoEntry  
SEQUENCE    
  INTEGER as ibmringFilterIfIndex  
  INTEGER as ibmringFilterInBcastType  
  INTEGER as ibmringFilterOutBcastType  
  INTEGER as ibmringFilterInFilterType  
  INTEGER as ibmringFilterOutFilterType  
  Counter as ibmringFilterInNotForwarded  
  Counter as ibmringFilterOutNotForwarded  

RingFilterInEntry  
SEQUENCE    
  INTEGER as ibmringFilterInIfIndex  
  INTEGER as ibmringFilterInNumber  
  INTEGER as ibmringFilterInMask  

RingFilterOutEntry  
SEQUENCE    
  INTEGER as ibmringFilterOutIfIndex  
  INTEGER as ibmringFilterOutNumber  
  INTEGER as ibmringFilterOutMask  

HopCountFilterInfoEntry  
SEQUENCE    
  INTEGER as ibmhopCountFilterIfIndex  
  INTEGER as ibmhopCountFilterBcastType  
  INTEGER as ibmhopCountFilterCount  

WindowFilterInfoEntry  
SEQUENCE    
  INTEGER as ibmwindowFilterIfIndex  
  INTEGER as ibmwindowFilterInBcastType  
  INTEGER as ibmwindowFilterOutBcastType  
  INTEGER as ibmwindowFilterInFilterType  
  INTEGER as ibmwindowFilterOutFilterType  
  Counter as ibmwindowFilterInNotForwarded  
  Counter as ibmwindowFilterOutNotForwarded  
  INTEGER as ibmwindowFilterType  

WindowFilterInEntry  
SEQUENCE    
  INTEGER as ibmwindowFilterInIfIndex  
  OCTET STRING as ibmwindowFilterInContents  
  OCTET STRING as ibmwindowFilterInMaskString  
  DisplayString as ibmwindowFilterInOffsetStart  
  OCTET STRING as ibmwindowFilterInNumBytes  
  OCTET STRING as ibmwindowFilterInOffset  
  INTEGER as ibmwindowFilterInId  
  INTEGER as ibmwindowFilterInType  

WindowFilterOutEntry  
SEQUENCE    
  INTEGER as ibmwindowFilterOutIfIndex  
  OCTET STRING as ibmwindowFilterOutContents  
  OCTET STRING as ibmwindowFilterOutMaskString  
  DisplayString as ibmwindowFilterOutOffsetStart  
  OCTET STRING as ibmwindowFilterOutNumBytes  
  OCTET STRING as ibmwindowFilterOutOffset  
  INTEGER as ibmwindowFilterOutId  
  INTEGER as ibmwindowFilterOutType  

FiltOrderInEntry  
SEQUENCE    
  INTEGER as ibmFiltOrderInIfIndex  
  INTEGER as ibmFiltOrderInPriority  
  DisplayString as ibmFiltOrderInName  
  INTEGER as ibmFiltOrderInType  

FiltOrderOutEntry  
SEQUENCE    
  INTEGER as ibmFiltOrderOutIfIndex  
  INTEGER as ibmFiltOrderOutPriority  
  DisplayString as ibmFiltOrderOutName  
  INTEGER as ibmFiltOrderOutType  

RIFFilterInfoEntry  
SEQUENCE    
  INTEGER as ibmRIFFilterIfIndex  
  INTEGER as ibmRIFFilterInBcastType  
  INTEGER as ibmRIFFilterOutBcastType  
  INTEGER as ibmRIFFilterInFilterType  
  INTEGER as ibmRIFFilterOutFilterType  
  Counter as ibmRIFFilterInNotForwarded  
  Counter as ibmRIFFilterOutNotForwarded  

RIFFilterInEntry  
SEQUENCE    
  INTEGER as ibmRIFFilterInIfIndex  
  INTEGER as ibmRIFFilterInRingNumber  
  INTEGER as ibmRIFFilterInRingMask  
  INTEGER as ibmRIFFilterInBridgeNumber  
  INTEGER as ibmRIFFilterInBridgeMask  
  INTEGER as ibmRIFFilterInRouteDesignator  

RIFFilterOutEntry  
SEQUENCE    
  INTEGER as ibmRIFFilterOutIfIndex  
  INTEGER as ibmRIFFilterOutNumber  
  INTEGER as ibmRIFFilterOutMask  
  INTEGER as ibmRIFFilterOutBridgeNumber  
  INTEGER as ibmRIFFilterOutBridgeMask  
  INTEGER as ibmRIFFilterOutRouteDesignator  

IbmfrDlcmiEntry  
SEQUENCE    
  INTEGER as ibmfrDlcmiIfIndex  
  INTEGER as ibmfrDlcmiState  
  INTEGER as ibmfrDlcmiAddress  
  INTEGER as ibmfrDlcmiAddressLen  
  INTEGER as ibmfrDlcmiPollingInterval  
  INTEGER as ibmfrDlcmiFullEnquiryInterval  
  INTEGER as ibmfrDlcmiErrorThreshold  
  INTEGER as ibmfrDlcmiMonitoredEvents  
  INTEGER as ibmfrDlcmiMaxSupportedVCs  
  INTEGER as ibmfrDlcmiMulticast  

IbmfrCircuitEntry  
SEQUENCE    
  INTEGER as ibmfrCircuitIfIndex  
  INTEGER as ibmfrCircuitDlci  
  INTEGER as ibmfrCircuitState  
  Counter as ibmfrCircuitReceivedFECNs  
  Counter as ibmfrCircuitReceivedBECNs  
  Counter as ibmfrCircuitSentFrames  
  Counter as ibmfrCircuitSentOctets  
  Counter as ibmfrCircuitReceivedFrames  
  Counter as ibmfrCircuitReceivedOctets  
  TimeTicks as ibmfrCircuitCreationTime  
  TimeTicks as ibmfrCircuitLastTimeChange  
  INTEGER as ibmfrCircuitCommittedBurst  
  INTEGER as ibmfrCircuitExcessBurst  
  INTEGER as ibmfrCircuitThroughput  

IbmfrErrEntry  
SEQUENCE    
  INTEGER as ibmfrErrIfIndex  
  INTEGER as ibmfrErrType  
  OCTET STRING as ibmfrErrData  
  TimeTicks as ibmfrErrTime  

IbmdlsRouterEntry  
SEQUENCE    
  IpAddress as ibmdlsRouterAddress  
  INTEGER as ibmdlsRouterStatus  
  INTEGER as ibmdlsRouterDefinedBy  
  INTEGER as ibmdlsRouterInFrames  
  INTEGER as ibmdlsRouterOutFrames  

IbmdlsLocalFrameFilterEntry  
SEQUENCE    
  INTEGER as ibmdlsLocalFrameFilterID  
  OCTET STRING as ibmdlsLocalFrameFilterSrcAddress  
  OCTET STRING as ibmdlsLocalFrameFilterSrcMask  
  OCTET STRING as ibmdlsLocalFrameFilterDestAddress  
  OCTET STRING as ibmdlsLocalFrameFilterDestMask  

IbmdlsRemoteFrameFilterEntry  
SEQUENCE    
  INTEGER as ibmdlsRemoteFrameFilterID  
  OCTET STRING as ibmdlsRemoteFrameFilterSrcAddress  
  OCTET STRING as ibmdlsRemoteFrameFilterSrcMask  
  OCTET STRING as ibmdlsRemoteFrameFilterDestAddress  
  OCTET STRING as ibmdlsRemoteFrameFilterDestMask  

IbmdlsLocalNameFilterEntry  
SEQUENCE    
  INTEGER as ibmdlsLocalNameFilterID  
  DisplayString as ibmdlsLocalNameFilterSrcAddress  
  DisplayString as ibmdlsLocalNameFilterDestAddress  

IbmdlsRemoteNameFilterEntry  
SEQUENCE    
  INTEGER as ibmdlsRemoteNameFilterID  
  DisplayString as ibmdlsRemoteNameFilterSrcAddress  
  DisplayString as ibmdlsRemoteNameFilterDestAddress  

IbmdlsDefaultDestEntry  
SEQUENCE    
  OCTET STRING as ibmdlsDefaultDestAddress  
  IpAddress as ibmdlsDefaultRouterAddress  

IbmdlsDefaultNBDestEntry  
SEQUENCE    
  DisplayString as ibmdlsDefaultNBDestName  
  IpAddress as ibmdlsDefaultNBRouterAddress  

IbmdlsStationEntry  
SEQUENCE    
  INTEGER as ibmdlsStationIfIndex  
  INTEGER as ibmdlsStationAddress  
  INTEGER as ibmdlsStationTransmitWindowCount  
  INTEGER as ibmdlsStationRetransmitCount  
  INTEGER as ibmdlsStationRetransmitThreshold  
  INTEGER as ibmdlsStationForceDisconnectTimeout  
  INTEGER as ibmdlsStationMaxIfieldSize  
  INTEGER as ibmdlsStationPrimaryRepollTimeout  
  INTEGER as ibmdlsStationPrimaryRepollCount  
  INTEGER as ibmdlsStationPrimaryRepollThreshold  
  INTEGER as ibmdlsStationPrimarySlowListTimeout  
  OCTET STRING as ibmdlsStationSrcAddress  
  OCTET STRING as ibmdlsStationDestAddress  

IbmdlsCirEntry  
SEQUENCE    
  INTEGER as ibmdlsCirIfIndex  
  OCTET STRING as ibmdlsCirSrcAddress  
  INTEGER as ibmdlsCirSrcSap  
  OCTET STRING as ibmdlsCirDestAddress  
  INTEGER as ibmdlsCirDestSap  
  IpAddress as ibmdlsCirPartnerRouterAddress  
  INTEGER as ibmdlsCirLocalLinkState  
  INTEGER as ibmdlsCirLocalLinkSubState  
  OCTET STRING as ibmdlsCirLocalLinkRouting  
  Counter as ibmdlsCirLocalLinkTestCmdsSent  
  Counter as ibmdlsCirLocalLinkTestCmdsFail  
  Counter as ibmdlsCirLocalLinkTestCmdsRcv  
  Counter as ibmdlsCirLocalLinkDataPktSent  
  Counter as ibmdlsCirLocalLinkDataPktResent  
  Counter as ibmdlsCirLocalLinkMaxContResent  
  Counter as ibmdlsCirLocalLinkDataPktRcv  
  Counter as ibmdlsCirLocalLinkInvalidPktRcv  
  Counter as ibmdlsCirLocalLinkAdpRcvErr  
  Counter as ibmdlsCirLocalLinkAdpSendErr  
  Counter as ibmdlsCirLocalLinkRcvInactiveTimeouts  
  Counter as ibmdlsCirLocalLinkCmdPollsSent  
  Counter as ibmdlsCirLocalLinkCmdRepollsSent  
  Counter as ibmdlsCirLocalLinkCmdContRepolls  

IbmpppLinkControlEntry  
SEQUENCE    
  INTEGER as ibmpppLinkControlIndex  
  INTEGER as ibmpppLinkCRCSize  
  INTEGER as ibmpppLinkRestartTimerValue  
  INTEGER as ibmpppLinkMaxRestarts  
  INTEGER as ibmpppLinkLocalMRU  
  INTEGER as ibmpppLinkRemoteMRU  
  OCTET STRING as ibmpppLinkLocalACCMap SIZE(4)  
  OCTET STRING as ibmpppLinkRemoteACCMap SIZE(4)  
  INTEGER as ibmpppLinkMagicLoopCount  
  INTEGER as ibmpppLinkCommand  

IbmpppLinkStatusEntry  
SEQUENCE    
  INTEGER as ibmpppLinkStatusIndex  
  INTEGER as ibmpppLinkVersion  
  INTEGER as ibmpppLinkCurrentState  
  INTEGER as ibmpppLinkPreviousState  
  TimeTicks as ibmpppLinkChangeTime  
  INTEGER as ibmpppLinkMagicNumber  
  INTEGER as ibmpppLinkLocalQualityPeriod  
  INTEGER as ibmpppLinkRemoteQualityPeriod  
  INTEGER as ibmpppLinkProtocolCompression  
  INTEGER as ibmpppLinkACCompression  
  INTEGER as ibmpppLinkMeasurementsValid  
  INTEGER as ibmpppLinkQuality  
  OBJECT IDENTIFIER as ibmpppLinkPhysical  

IbmpppLinkErrorsEntry  
SEQUENCE    
  INTEGER as ibmpppLinkErrorsIndex  
  Counter as ibmpppLinkBadAddresses  
  OCTET STRING as ibmpppLinkLastBadAddress  
  Counter as ibmpppLinkBadControls  
  OCTET STRING as ibmpppLinkLastBadControl  
  OCTET STRING as ibmpppLinkLastUnknownProtocol  
  Counter as ibmpppLinkInvalidProtocols  
  OCTET STRING as ibmpppLinkLastInvalidProtocol  
  Counter as ibmpppLinkPacketTooLongs  
  Counter as ibmpppLinkBadCRCs  
  Counter as ibmpppLinkConfigTimeouts  
  Counter as ibmpppLinkTerminateTimeouts  

IbmpppLinkQualityEntry  
SEQUENCE    
  INTEGER as ibmpppLinkQualityIndex  
  Counter as ibmpppLinkInTxLQRs  
  Counter as ibmpppLinkInTxPackets  
  Counter as ibmpppLinkLastOutTxPackets  
  Counter as ibmpppLinkInTxOctets  
  Counter as ibmpppLinkLastOutTxOctets  
  Counter as ibmpppLinkInRxPackets  
  Counter as ibmpppLinkLastInRxPackets  
  Counter as ibmpppLinkInRxOctets  
  Counter as ibmpppLinkLastInRxOctets  

IbmpppIPEntry  
SEQUENCE    
  INTEGER as ibmpppIPLinkNumber  
  Counter as ibmpppIPRejects  
  Counter as ibmpppIPInPackets  
  Counter as ibmpppIPInOctets  
  Counter as ibmpppIPOutPackets  
  Counter as ibmpppIPOutOctets  

IbmpppIPCPEntry  
SEQUENCE    
  INTEGER as ibmpppIPCPLinkNumber  
  Counter as ibmpppIPCPRejects  
  Counter as ibmpppIPCPInPackets  
  Counter as ibmpppIPCPInOctets  
  Counter as ibmpppIPCPOutPackets  
  Counter as ibmpppIPCPOutOctets  
  INTEGER as ibmpppIPCPCompressionType  

IbmpppLCPEntry  
SEQUENCE    
  INTEGER as ibmpppLCPLinkNumber  
  Counter as ibmpppLCPRejects  
  Counter as ibmpppLCPInPackets  
  Counter as ibmpppLCPInOctets  
  Counter as ibmpppLCPOutPackets  
  Counter as ibmpppLCPOutOctets  
  Counter as ibmpppLCPOutCRs  
  Counter as ibmpppLCPInCRs  
  Counter as ibmpppLCPOutCAs  
  Counter as ibmpppLCPInCAs  
  Counter as ibmpppLCPOutCNs  
  Counter as ibmpppLCPInCNs  
  Counter as ibmpppLCPOutCRejs  
  Counter as ibmpppLCPInCRejs  
  Counter as ibmpppLCPOutTRs  
  Counter as ibmpppLCPInTRs  
  Counter as ibmpppLCPOutTAs  
  Counter as ibmpppLCPInTAs  
  Counter as ibmpppLCPOutCodeRejs  
  Counter as ibmpppLCPInCodeRejs  
  Counter as ibmpppLCPOutEchoReqs  
  Counter as ibmpppLCPInEchoReqs  
  Counter as ibmpppLCPOutEchoReps  
  Counter as ibmpppLCPInEchoReps  
  Counter as ibmpppLCPOutDiscReqs  
  Counter as ibmpppLCPInDiscReqs  

IbmXnsConfigEntry  
SEQUENCE    
  INTEGER as ibmxnsPortIfIndex  
  INTEGER as ibmxnsPortStatus  
  INTEGER as ibmxnsidpChecksum  
  INTEGER as ibmxnsErrpActive  
  INTEGER as ibmxnsLoopbackActive  

IbmXnsAddrEntry  
SEQUENCE    
  OCTET STRING as ibmxnsAddrAddress  
  INTEGER as ibmxnsAddrIfIndex  

IbmXnsRouteEntry  
SEQUENCE    
  OCTET STRING as ibmxnsRouteDest  
  INTEGER as ibmxnsRouteIfIndex  
  OCTET STRING as ibmxnsRouteNextHop  
  INTEGER as ibmxnsRouteMetric  
  Counter as ibmxnsRouteUse  

IbmXnsFilterEntry  
SEQUENCE    
  INTEGER as ibmxnsFilterIfIndex  
  INTEGER as ibmxnsFilterNumber  
  OCTET STRING as ibmxnsFilterValue  
  OCTET STRING as ibmxnsFilterMask  
  INTEGER as ibmxnsFilterType  
  INTEGER as ibmxnsFilterHCCompare  
  Counter as ibmxnsFilterUse  

IbmIpxConfigEntry  
SEQUENCE    
  INTEGER as ibmipxPortIfIndex  
  INTEGER as ibmipxPortStatus  
  INTEGER as ibmipxidpChecksum  
  INTEGER as ibmipxLoopbackActive  

IbmIpxAddrEntry  
SEQUENCE    
  OCTET STRING as ibmipxAddrAddress  
  INTEGER as ibmipxAddrIfIndex  

IbmIpxRouteEntry  
SEQUENCE    
  OCTET STRING as ibmipxRouteDest  
  INTEGER as ibmipxRouteIfIndex  
  OCTET STRING as ibmipxRouteNextHop  
  INTEGER as ibmipxRouteMetric  
  Counter as ibmipxRouteUse  

IbmIpxFilterEntry  
SEQUENCE    
  INTEGER as ibmipxFilterIfIndex  
  INTEGER as ibmipxFilterNumber  
  OCTET STRING as ibmipxFilterValue  
  OCTET STRING as ibmipxFilterMask  
  INTEGER as ibmipxFilterType  
  INTEGER as ibmipxFilterHCCompare  
  Counter as ibmipxFilterUse  

IbmIpxsapServerEntry  
SEQUENCE    
  INTEGER as ibmipxsapServerType  
  OCTET STRING as ibmipxsapServerNet  
  OCTET STRING as ibmipxsapServerHost  
  INTEGER as ibmipxsapServerSocket  
  DisplayString as ibmipxsapServerName  
  INTEGER as ibmipxsapServerAge  
  INTEGER as ibmipxsapServerHops  
  INTEGER as ibmipxsapServerIfIndex  
  INTEGER as ibmipxsapServerIndex  
  Counter as ibmipxsapServerRequestsFiltered  

CYLINKStatusEntry  
SEQUENCE    
  INTEGER as cylinkIndex  
  INTEGER as cylinkLinkState  
  INTEGER as cylinkLoopback  
  INTEGER as cylinkQRSS  

CYLINKConfigEntry  
SEQUENCE    
  INTEGER as cylinkConfigIndex  
  INTEGER as cylinkSerialNumber  
  DisplayString as cylinkSoftwareVersion SIZE(0..4)  
  INTEGER as cylinkDTEFraming  
  INTEGER as cylinkNetworkFraming  
  INTEGER as cylinkDTEDS1Mode  
  INTEGER as cylinkNetworkDS1Mode  
  INTEGER as cylinkOnesResponsibility  
  INTEGER as cylinkOnesControl  
  INTEGER as cylinkZeroProtection  
  INTEGER as cylinkClockSource  
  INTEGER as cylinkClockFrequency  
  INTEGER as cylinkClockBackup  
  INTEGER as cylinkDIUFrequency  
  INTEGER as cylinkDIUTiming  
  INTEGER as cylinkDialoutCapability  
  INTEGER as cylinkDialoutHoldoff 1..99  
  DisplayString as cylinkPrimaryPhone SIZE(0..19)  
  DisplayString as cylinkSecondaryPhone SIZE(0..19)  
  INTEGER as cylinkAlarmRepeatTime 1..99  
  INTEGER as cylinkESThreshold 1..99  
  INTEGER as cylinkSecondaryContact  

IbmDot1dBasePortEntry  
SEQUENCE    
  INTEGER as ibmdot1dBasePort  
  INTEGER as ibmdot1dBasePortIfIndex  
  OBJECT IDENTIFIER as ibmdot1dBasePortCircuit  
  Counter as ibmdot1dBasePortDelayExceededDiscards  
  Counter as ibmdot1dBasePortMtuExceededDiscards  

IbmDot1dStpPortEntry  
SEQUENCE    
  INTEGER as ibmdot1dStpPort  
  INTEGER as ibmdot1dStpPortPriority  
  INTEGER as ibmdot1dStpPortState  
  INTEGER as ibmdot1dStpPortEnable  
  INTEGER as ibmdot1dStpPortPathCost  
  OCTET STRING as ibmdot1dStpPortDesignatedRoot  
  INTEGER as ibmdot1dStpPortDesignatedCost  
  OCTET STRING as ibmdot1dStpPortDesignatedBridge  
  OCTET STRING as ibmdot1dStpPortDesignatedPort  
  Counter as ibmdot1dStpPortForwardTransitions  

IbmDot1dTpFdbEntry  
SEQUENCE    
  OCTET STRING as ibmdot1dTpFdbAddress  
  INTEGER as ibmdot1dTpFdbPort  
  INTEGER as ibmdot1dTpFdbStatus  

IbmDot1dTpPortEntry  
SEQUENCE    
  INTEGER as ibmdot1dTpPort  
  INTEGER as ibmdot1dTpPortMaxInfo  
  Counter as ibmdot1dTpPortInFrames  
  Counter as ibmdot1dTpPortOutFrames  
  Counter as ibmdot1dTpPortInDiscards  

IbmDot1dStaticEntry  
SEQUENCE    
  OCTET STRING as ibmdot1dStaticAddress  
  INTEGER as ibmdot1dStaticReceivePort  
  OCTET STRING as ibmdot1dStaticAllowedToGoTo  
  INTEGER as ibmdot1dStaticStatus  

TBMacAddrFilterInfoEntry  
SEQUENCE    
  INTEGER as ibmtbmacFiltIfIndex  
  INTEGER as ibmtbmacFiltInFilterType  
  INTEGER as ibmtbmacFiltOutFilterType  
  Counter as ibmtbmacFiltInNotForwarded  
  Counter as ibmtbmacFiltOutNotForwarded  

TBMacAddrFilterInEntry  
SEQUENCE    
  INTEGER as ibmtbmacFiltInIfIndex  
  OCTET STRING as ibmtbmacFiltInSrcAddress  
  OCTET STRING as ibmtbmacFiltInSrcMask  
  OCTET STRING as ibmtbmacFiltInDestAddress  
  OCTET STRING as ibmtbmacFiltInDestMask  

TBMacAddrFilterOutEntry  
SEQUENCE    
  INTEGER as ibmtbmacFiltOutIfIndex  
  OCTET STRING as ibmtbmacFiltOutSrcAddress  
  OCTET STRING as ibmtbmacFiltOutSrcMask  
  OCTET STRING as ibmtbmacFiltOutDestAddress  
  OCTET STRING as ibmtbmacFiltOutDestMask  

TBSapFilterInfoEntry  
SEQUENCE    
  INTEGER as ibmtbsapFiltIfIndex  
  OCTET STRING as ibmtbsapFiltIn  
  OCTET STRING as ibmtbsapFiltOut  
  Counter as ibmtbsapFiltInNotForwarded  
  Counter as ibmtbsapFiltOutNotForwarded  

TBEthTypeFilterInfoEntry  
SEQUENCE    
  INTEGER as ibmtbEthTypeFiltIfIndex  
  INTEGER as ibmtbEthTypeFiltInFilterType  
  INTEGER as ibmtbEthTypeFiltOutFilterType  
  Counter as ibmtbEthTypeFiltInNotForwarded  
  Counter as ibmtbEthTypeFiltOutNotForwarded  

TBEthTypeFilterInEntry  
SEQUENCE    
  INTEGER as ibmtbEthTypeFiltInIfIndex  
  OCTET STRING as ibmtbEthTypeFiltInValue SIZE(2)  
  OCTET STRING as ibmtbEthTypeFiltInMask SIZE(2)  

TBEthTypeFilterOutEntry  
SEQUENCE    
  INTEGER as ibmtbEthTypeFiltOutIfIndex  
  OCTET STRING as ibmtbEthTypeFiltOutValue SIZE(2)  
  OCTET STRING as ibmtbEthTypeFiltOutMask SIZE(2)  

TBWindowFilterInfoEntry  
SEQUENCE    
  INTEGER as ibmtbwinFiltIfIndex  
  INTEGER as ibmtbwinFiltInFilterType  
  INTEGER as ibmtbwinFiltOutFilterType  
  Counter as ibmtbwinFiltInNotForwarded  
  Counter as ibmtbwinFiltOutNotForwarded  

TBWindowFilterInEntry  
SEQUENCE    
  INTEGER as ibmtbwinFiltInIfIndex  
  OCTET STRING as ibmtbwinFiltInContents  
  OCTET STRING as ibmtbwinFiltInMaskString  
  DisplayString as ibmtbwinFiltInOffsetStart  
  OCTET STRING as ibmtbwinFiltInNumBytes  
  OCTET STRING as ibmtbwinFiltInOffset  
  INTEGER as ibmtbwinFiltInId  

TBWindowFilterOutEntry  
SEQUENCE    
  INTEGER as ibmtbwinFiltOutIfIndex  
  OCTET STRING as ibmtbwinFiltOutContents  
  OCTET STRING as ibmtbwinFiltOutMaskString  
  DisplayString as ibmtbwinFiltOutOffsetStart  
  OCTET STRING as ibmtbwinFiltOutNumBytes  
  OCTET STRING as ibmtbwinFiltOutOffset  
  INTEGER as ibmtbwinFiltOutId  

TBFiltOrderInEntry  
SEQUENCE    
  INTEGER as ibmtbFiltOrderInIfIndex  
  INTEGER as ibmtbFiltOrderInPriority  
  DisplayString as ibmtbFiltOrderInName  

TBFiltOrderOutEntry  
SEQUENCE    
  INTEGER as ibmtbFiltOrderOutIfIndex  
  INTEGER as ibmtbFiltOrderOutPriority  
  DisplayString as ibmtbFiltOrderOutName  

SelectNetEntry  
SEQUENCE    
  INTEGER as ibmSelectNetIndex  
  OCTET STRING as ibmSelectNetZone  
  OCTET STRING as ibmSelectNetNetStart  
  OCTET STRING as ibmSelectNetNetEnd  
  OCTET STRING as ibmSelectNetInterfaceNetStart  

AtportFilterEntry  
SEQUENCE    
  INTEGER as ibmatportFilterIndex  
  OCTET STRING as ibmatportFilterNetStart  
  OCTET STRING as ibmatportFilterNetEnd  

SelectNetFilterEntry  
SEQUENCE    
  INTEGER as ibmSelectNetFilterIndex  
  OCTET STRING as ibmSelectNetFilterNetStart  
  OCTET STRING as ibmSelectNetFilterNetEnd  

IbmdecLANCircuitEntry  
SEQUENCE    
  INTEGER as ibmdecLANCircuitIndex  
  INTEGER as ibmdecLANCircuitType  
  INTEGER as ibmdecLANCircuitSourceRoute  
  INTEGER as ibmdecLANCircuitAddrType  

IbmipPtyQueueEnableEntry  
SEQUENCE    
  INTEGER as ibmipPtyQueueEnableIfIndex  
  INTEGER as ibmipPtyQueueEnable  
  INTEGER as ibmipPtyQueueDefault  

IbmipPtyQueueEntry  
SEQUENCE    
  INTEGER as ibmipPtyQueueIfIndex  
  INTEGER as ibmipPtyQueuePort  
  INTEGER as ibmipPtyQueueType  
  INTEGER as ibmipPtyQueueNumber  

IbmipFilterEntry  
SEQUENCE    
  INTEGER as ibmipFilterIfIndex  
  INTEGER as ibmipFilterId  
  INTEGER as ibmipFilterScope  
  INTEGER as ibmipFilterType  
  INTEGER as ibmipFilterPermitDeny  
  IpAddress as ibmipFilterAddr1  
  IpAddress as ibmipFilterMask1  
  IpAddress as ibmipFilterAddr2  
  IpAddress as ibmipFilterMask2  

IbmipFilterExtEntry  
SEQUENCE    
  INTEGER as ibmipFilterExtIfIndex  
  INTEGER as ibmipFilterExtFilterId  
  INTEGER as ibmipFilterExtValue  
  INTEGER as ibmipFilterExtProtocol  

IbmPtyQueueingEntry  
SEQUENCE    
  INTEGER as ibmPtyQueueingIfIndex  
  INTEGER as ibmPtyQueueingQnum  
  INTEGER as ibmPtyQueueingLBA  
  INTEGER as ibmPtyQueueingQBR  
  Counter as ibmPtyQueueingDiscards  

IbmTGEntry  
SEQUENCE    
  INTEGER as ibmTGProtocol  
  INTEGER as ibmTGIfIndex  
  INTEGER as ibmTGEnable  
  DisplayString as ibmTGGroupName  
  Counter as ibmTGSwitchOuts  

IbmvNbrEntry  
SEQUENCE    
  OCTET STRING as ibmvNbrNetid  
  OCTET STRING as ibmvNbrSubNetid  
  INTEGER as ibmvNbrType  
  INTEGER as ibmvNbrIfType  
  OCTET STRING as ibmvNbrRemAddress  
  OCTET STRING as ibmvNbrLocAddress  
  INTEGER as ibmvNbrLocSlot  
  INTEGER as ibmvNbrLocPort  
  INTEGER as ibmvNbrAging  
  INTEGER as ibmvNbrFlags  
  OCTET STRING as ibmvNbrRIF  
  INTEGER as ibmvNbrIfIndex  
  INTEGER as ibmvNbrMetric  

IbmvRtCfgInFltEntry  
SEQUENCE    
  OCTET STRING as ibmvRtCfgInFltNetID  
  INTEGER as ibmvRtCfgInFltIfIndex  
  INTEGER as ibmvRtCfgInFltMode  
  Counter as ibmvRtCfgInFltUses  

IbmvRtCfgOutFltEntry  
SEQUENCE    
  OCTET STRING as ibmvRtCfgOutFltNetID  
  INTEGER as ibmvRtCfgOutFltIfIndex  
  INTEGER as ibmvRtCfgOutFltMode  
  Counter as ibmvRtCfgOutFltUses  

IbmvRtCfgFltEntry  
SEQUENCE    
  OCTET STRING as ibmvRtCfgFltNetID  
  INTEGER as ibmvRtCfgFltMode  
  Counter as ibmvRtCfgFltUses  

IbmvRtEntry  
SEQUENCE    
  OCTET STRING as ibmvRtNetid  
  INTEGER as ibmvRtMetric  
  INTEGER as ibmvRtIdle  
  OCTET STRING as ibmvRtGateNetid  
  INTEGER as ibmvRtIfIndex  
  INTEGER as ibmvRtState  

IbmvPortCfgEntry  
SEQUENCE    
  INTEGER as ibmvPortCfgIfIndex  
  INTEGER as ibmvPortCfgARP  
  INTEGER as ibmvPortCfgServ  
  INTEGER as ibmvPortCfgHCtoServ  
  INTEGER as ibmvPortCfgPerUpdate  
  INTEGER as ibmvPortCfgMetric  
  INTEGER as ibmvPortCfgTR  
  INTEGER as ibmvPortCfgEN  
  INTEGER as ibmvPortCfgInFlt  
  INTEGER as ibmvPortCfgInFltNum  
  INTEGER as ibmvPortCfgOutFlt  
  INTEGER as ibmvPortCfgOutFltNum  

IbmvFltEntry  
SEQUENCE    
  INTEGER as ibmvFltIfIndex  
  INTEGER as ibmvFltNo  
  INTEGER as ibmvFltMode  
  OCTET STRING as ibmvFltValue  
  OCTET STRING as ibmvFltMask  
  INTEGER as ibmvFltType  
  INTEGER as ibmvFltHCCompare  
  Counter as ibmvFltUses  

IbmvifEntry  
SEQUENCE    
  INTEGER as ibmvifSlot  
  INTEGER as ibmvifPort  
  DisplayString as ibmvifDescr  
  OCTET STRING as ibmvifAddress  
  Counter as ibmvifInPkts  
  Counter as ibmvifInErrs  
  Counter as ibmvifOutPkts  
  Counter as ibmvifOutErrs  

IbmappnNodePortEntry  
SEQUENCE    
  DisplayString as ibmappnNodePortName  
  INTEGER as ibmappnNodePortState  
  INTEGER as ibmappnNodePortDlcType  
  INTEGER as ibmappnNodePortPortType  
  INTEGER as ibmappnNodePortSIMRIM  
  INTEGER as ibmappnNodePortLsRole  
  INTEGER as ibmappnNodePortMaxRcvBtuSize  
  INTEGER as ibmappnNodePortMaxIframeWindow  
  Counter as ibmappnNodePortDefLsGoodXids  
  Counter as ibmappnNodePortDefLsBadXids  
  Counter as ibmappnNodePortDynLsGoodXids  
  Counter as ibmappnNodePortDynLsBadXids  
  OBJECT IDENTIFIER as ibmappnNodePortSpecific  

IbmappnNodePortIpEntry  
SEQUENCE    
  DisplayString as ibmappnNodePortIpName  
  INTEGER as ibmappnNodePortIpPortNum  

IbmappnNodePortDlsEntry  
SEQUENCE    
  DisplayString as ibmappnNodePortDlsName  
  OCTET STRING as ibmappnNodePortDlsMac  
  OCTET STRING as ibmappnNodePortDlsSap  

IbmappnNodePortTrEntry  
SEQUENCE    
  DisplayString as ibmappnNodePortTrName  
  OCTET STRING as ibmappnNodePortTrMac  
  OCTET STRING as ibmappnNodePortTrSap  

IbmappnNodePortDlcTraceEntry  
SEQUENCE    
  DisplayString as ibmappnNodePortDlcTracPortName  
  INTEGER as ibmappnNodePortDlcTracIndex  
  INTEGER as ibmappnNodePortDlcTracDlcType  
  DisplayString as ibmappnNodePortDlcTracLocalAddr  
  DisplayString as ibmappnNodePortDlcTracRemoteAddr  
  INTEGER as ibmappnNodePortDlcTracMsgType  
  INTEGER as ibmappnNodePortDlcTracCmdType  
  INTEGER as ibmappnNodePortDlcTracUseWan  

IbmappnNodeLsEntry  
SEQUENCE    
  DisplayString as ibmappnNodeLsName  
  DisplayString as ibmappnNodeLsPortName  
  INTEGER as ibmappnNodeLsDlcType  
  INTEGER as ibmappnNodeLsDynamic  
  INTEGER as ibmappnNodeLsState  
  DisplayString as ibmappnNodeLsCpName  
  INTEGER as ibmappnNodeLsTgNum  
  INTEGER as ibmappnNodeLsLimResource  
  INTEGER as ibmappnNodeLsMigration  
  DisplayString as ibmappnNodeLsBlockNum  
  DisplayString as ibmappnNodeLsIdNum  
  INTEGER as ibmappnNodeLsCpCpSession  
  INTEGER as ibmappnNodeLsTargetPacingCount  
  INTEGER as ibmappnNodeLsMaxSendBtuSize  
  INTEGER as ibmappnNodeLsEffCap  
  INTEGER as ibmappnNodeLsConnCost  
  INTEGER as ibmappnNodeLsByteCost  
  INTEGER as ibmappnNodeLsSecurity  
  INTEGER as ibmappnNodeLsDelay  
  INTEGER as ibmappnNodeLsUsr1  
  INTEGER as ibmappnNodeLsUsr2  
  INTEGER as ibmappnNodeLsUsr3  
  Counter as ibmappnNodeLsInXidBytes  
  Counter as ibmappnNodeLsInMsgBytes  
  Counter as ibmappnNodeLsInXidFrames  
  Counter as ibmappnNodeLsInMsgFrames  
  Counter as ibmappnNodeLsOutXidBytes  
  Counter as ibmappnNodeLsOutMsgBytes  
  Counter as ibmappnNodeLsOutXidFrames  
  Counter as ibmappnNodeLsOutMsgFrames  
  Counter as ibmappnNodeLsEchoRsps  
  INTEGER as ibmappnNodeLsCurrentDelay  
  INTEGER as ibmappnNodeLsMaxDelay  
  INTEGER as ibmappnNodeLsMinDelay  
  TimeTicks as ibmappnNodeLsMaxDelayTime  
  Counter as ibmappnNodeLsGoodXids  
  Counter as ibmappnNodeLsBadXids  
  OBJECT IDENTIFIER as ibmappnNodeLsSpecific  
  INTEGER as ibmappnNodeLsSubState  
  TimeTicks as ibmappnNodeLsStartTime  
  TimeTicks as ibmappnNodeLsActiveTime  
  TimeTicks as ibmappnNodeLsCurrentStateTime  

IbmappnNodeLsIpEntry  
SEQUENCE    
  DisplayString as ibmappnNodeLsIpName  
  INTEGER as ibmappnNodeLsIpState  
  IpAddress as ibmappnNodeLsLocalIpAddr  
  INTEGER as ibmappnNodeLsLocalIpPortNum  
  IpAddress as ibmappnNodeLsRemoteIpAddr  
  INTEGER as ibmappnNodeLsRemoteIpPortNum  

IbmappnNodeLsDlsEntry  
SEQUENCE    
  DisplayString as ibmappnNodeLsDlsName  
  INTEGER as ibmappnNodeLsDlsState  
  OCTET STRING as ibmappnNodeLsLocalDlsMac  
  OCTET STRING as ibmappnNodeLsLocalDlsSap  
  OCTET STRING as ibmappnNodeLsRemoteDlsMac  
  OCTET STRING as ibmappnNodeLsRemoteDlsSap  

IbmappnNodeLsTrEntry  
SEQUENCE    
  DisplayString as ibmappnNodeLsTrName  
  INTEGER as ibmappnNodeLsTrState  
  OCTET STRING as ibmappnNodeLsLocalTrMac  
  OCTET STRING as ibmappnNodeLsLocalTrSap  
  OCTET STRING as ibmappnNodeLsRemoteTrMac  
  OCTET STRING as ibmappnNodeLsRemoteTrSap  

IbmappnNodeLsStatusEntry  
SEQUENCE    
  INTEGER as ibmappnNodeLsStatusIndex  
  TimeTicks as ibmappnNodeLsStatusTime  
  DisplayString as ibmappnNodeLsStatusLsName  
  DisplayString as ibmappnNodeLsStatusCpName  
  OCTET STRING as ibmappnNodeLsStatusNodeId  
  INTEGER as ibmappnNodeLsStatusTgNum  
  OCTET STRING as ibmappnNodeLsStatusGeneralSense  
  INTEGER as ibmappnNodeLsStatusNofRetry  
  OCTET STRING as ibmappnNodeLsStatusEndSense  
  OCTET STRING as ibmappnNodeLsStatusXidLocalSense  
  OCTET STRING as ibmappnNodeLsStatusXidRemoteSense  
  INTEGER as ibmappnNodeLsStatusXidByteInError  
  INTEGER as ibmappnNodeLsStatusXidBitInError  
  INTEGER as ibmappnNodeLsStatusDlcType  
  DisplayString as ibmappnNodeLsStatusLocalAddr  
  DisplayString as ibmappnNodeLsStatusRemoteAddr  

IbmappnNnTopoRouteEntry  
SEQUENCE    
  DisplayString as ibmappnNnTopoRouteCos  
  Counter as ibmappnNnTopoRouteTrees  
  Counter as ibmappnNnTopoRouteCalcs  
  Counter as ibmappnNnTopoRouteRejs  

IbmappnNnAdjNodeEntry  
SEQUENCE    
  DisplayString as ibmappnNnAdjNodeAdjName  
  INTEGER as ibmappnNnAdjNodeCpCpSessStatus  
  Gauge as ibmappnNnAdjNodeOutOfSeqTdus  
  INTEGER as ibmappnNnAdjNodeLastFrsnSent  
  INTEGER as ibmappnNnAdjNodeLastFrsnRcvd  

IbmappnNnTopologyEntry  
SEQUENCE    
  DisplayString as ibmappnNnNodeName  
  INTEGER as ibmappnNnNodeFrsn  
  INTEGER as ibmappnNnNodeEntryTimeLeft  
  INTEGER as ibmappnNnNodeType  
  INTEGER as ibmappnNnNodeRsn  
  INTEGER as ibmappnNnNodeRouteAddResist  
  INTEGER as ibmappnNnNodeCongested  
  INTEGER as ibmappnNnNodeIsrDepleted  
  INTEGER as ibmappnNnNodeEndptDepleted  
  INTEGER as ibmappnNnNodeQuiescing  
  INTEGER as ibmappnNnNodeGateway  
  INTEGER as ibmappnNnNodeCentralDirectory  
  INTEGER as ibmappnNnNodeIsr  
  INTEGER as ibmappnNnNodeChainSupport  

IbmappnNnTgTopologyEntry  
SEQUENCE    
  DisplayString as ibmappnNnTgOwner  
  DisplayString as ibmappnNnTgDest  
  INTEGER as ibmappnNnTgNum  
  INTEGER as ibmappnNnTgFrsn  
  INTEGER as ibmappnNnTgEntryTimeLeft  
  INTEGER as ibmappnNnTgDestVirtual  
  OCTET STRING as ibmappnNnTgDlcData  
  INTEGER as ibmappnNnTgRsn  
  INTEGER as ibmappnNnTgOperational  
  INTEGER as ibmappnNnTgQuiescing  
  INTEGER as ibmappnNnTgCpCpSession  
  INTEGER as ibmappnNnTgEffCap  
  INTEGER as ibmappnNnTgConnCost  
  INTEGER as ibmappnNnTgByteCost  
  INTEGER as ibmappnNnTgSecurity  
  INTEGER as ibmappnNnTgDelay  
  INTEGER as ibmappnNnTgModemClass  
  INTEGER as ibmappnNnTgUsr1  
  INTEGER as ibmappnNnTgUsr2  
  INTEGER as ibmappnNnTgUsr3  

IbmappnNnTopologyFREntry  
SEQUENCE    
  DisplayString as ibmappnNnNodeFRName  
  INTEGER as ibmappnNnNodeFRFrsn  
  INTEGER as ibmappnNnNodeFREntryTimeLeft  
  INTEGER as ibmappnNnNodeFRType  
  INTEGER as ibmappnNnNodeFRRsn  
  INTEGER as ibmappnNnNodeFRRouteAddResist  
  INTEGER as ibmappnNnNodeFRCongested  
  INTEGER as ibmappnNnNodeFRIsrDepleted  
  INTEGER as ibmappnNnNodeFREndptDepleted  
  INTEGER as ibmappnNnNodeFRQuiescing  
  INTEGER as ibmappnNnNodeFRGateway  
  INTEGER as ibmappnNnNodeFRCentralDirectory  
  INTEGER as ibmappnNnNodeFRIsr  
  INTEGER as ibmappnNnNodeFRChainSupport  

IbmappnNnTgTopologyFREntry  
SEQUENCE    
  DisplayString as ibmappnNnTgFROwner  
  DisplayString as ibmappnNnTgFRDest  
  INTEGER as ibmappnNnTgFRNum  
  INTEGER as ibmappnNnTgFRFrsn  
  INTEGER as ibmappnNnTgFREntryTimeLeft  
  INTEGER as ibmappnNnTgFRDestVirtual  
  OCTET STRING as ibmappnNnTgFRDlcData  
  INTEGER as ibmappnNnTgFRRsn  
  INTEGER as ibmappnNnTgFROperational  
  INTEGER as ibmappnNnTgFRQuiescing  
  INTEGER as ibmappnNnTgFRCpCpSession  
  INTEGER as ibmappnNnTgFREffCap  
  INTEGER as ibmappnNnTgFRConnCost  
  INTEGER as ibmappnNnTgFRByteCost  
  INTEGER as ibmappnNnTgFRSecurity  
  INTEGER as ibmappnNnTgFRDelay  
  INTEGER as ibmappnNnTgFRModemClass  
  INTEGER as ibmappnNnTgFRUsr1  
  INTEGER as ibmappnNnTgFRUsr2  
  INTEGER as ibmappnNnTgFRUsr3  

IbmappnLocalTgEntry  
SEQUENCE    
  DisplayString as ibmappnLocalTgDest  
  INTEGER as ibmappnLocalTgNum  
  INTEGER as ibmappnLocalTgDestVirtual  
  OCTET STRING as ibmappnLocalTgDlcData  
  INTEGER as ibmappnLocalTgRsn  
  INTEGER as ibmappnLocalTgQuiescing  
  INTEGER as ibmappnLocalTgOperational  
  INTEGER as ibmappnLocalTgCpCpSession  
  INTEGER as ibmappnLocalTgEffCap  
  INTEGER as ibmappnLocalTgConnCost  
  INTEGER as ibmappnLocalTgByteCost  
  INTEGER as ibmappnLocalTgSecurity  
  INTEGER as ibmappnLocalTgDelay  
  INTEGER as ibmappnLocalTgModemClass  
  INTEGER as ibmappnLocalTgUsr1  
  INTEGER as ibmappnLocalTgUsr2  
  INTEGER as ibmappnLocalTgUsr3  

IbmappnLocalEnEntry  
SEQUENCE    
  DisplayString as ibmappnLocalEnName  
  INTEGER as ibmappnLocalEnEntryTimeLeft  
  INTEGER as ibmappnLocalEnType  

IbmappnLocalEnTgEntry  
SEQUENCE    
  DisplayString as ibmappnLocalEnTgOrigin  
  DisplayString as ibmappnLocalEnTgDest  
  INTEGER as ibmappnLocalEnTgNum  
  INTEGER as ibmappnLocalEnTgEntryTimeLeft  
  INTEGER as ibmappnLocalEnTgDestVirtual  
  OCTET STRING as ibmappnLocalEnTgDlcData  
  INTEGER as ibmappnLocalEnTgOperational  
  INTEGER as ibmappnLocalEnTgCpCpSession  
  INTEGER as ibmappnLocalEnTgEffCap  
  INTEGER as ibmappnLocalEnTgConnCost  
  INTEGER as ibmappnLocalEnTgByteCost  
  INTEGER as ibmappnLocalEnTgSecurity  
  INTEGER as ibmappnLocalEnTgDelay  
  INTEGER as ibmappnLocalEnTgModemClass  
  INTEGER as ibmappnLocalEnTgUsr1  
  INTEGER as ibmappnLocalEnTgUsr2  
  INTEGER as ibmappnLocalEnTgUsr3  

IbmappnDirEntry  
SEQUENCE    
  DisplayString as ibmappnDirLuName  
  DisplayString as ibmappnDirServerName  
  DisplayString as ibmappnDirLuOwnerName  
  INTEGER as ibmappnDirLuLocation  
  INTEGER as ibmappnDirType  
  INTEGER as ibmappnDirWildCard  

IbmappnCosModeEntry  
SEQUENCE    
  DisplayString as ibmappnCosModeName  
  DisplayString as ibmappnCosModeCosName  

IbmappnCosNameEntry  
SEQUENCE    
  DisplayString as ibmappnCosName  
  INTEGER as ibmappnCosTransPriority  

IbmappnCosNodeRowEntry  
SEQUENCE    
  DisplayString as ibmappnCosNodeRowName  
  INTEGER as ibmappnCosNodeRowIndex  
  DisplayString as ibmappnCosNodeRowWgt  
  INTEGER as ibmappnCosNodeRowResistMin  
  INTEGER as ibmappnCosNodeRowResistMax  
  INTEGER as ibmappnCosNodeRowMinCongestAllow  
  INTEGER as ibmappnCosNodeRowMaxCongestAllow  

IbmappnCosTgRowEntry  
SEQUENCE    
  DisplayString as ibmappnCosTgRowName  
  INTEGER as ibmappnCosTgRowIndex  
  DisplayString as ibmappnCosTgRowWgt  
  INTEGER as ibmappnCosTgRowEffCapMin  
  INTEGER as ibmappnCosTgRowEffCapMax  
  INTEGER as ibmappnCosTgRowConnCostMin  
  INTEGER as ibmappnCosTgRowConnCostMax  
  INTEGER as ibmappnCosTgRowByteCostMin  
  INTEGER as ibmappnCosTgRowByteCostMax  
  INTEGER as ibmappnCosTgRowSecurityMin  
  INTEGER as ibmappnCosTgRowSecurityMax  
  INTEGER as ibmappnCosTgRowDelayMin  
  INTEGER as ibmappnCosTgRowDelayMax  
  INTEGER as ibmappnCosTgRowUsr1Min  
  INTEGER as ibmappnCosTgRowUsr1Max  
  INTEGER as ibmappnCosTgRowUsr2Min  
  INTEGER as ibmappnCosTgRowUsr2Max  
  INTEGER as ibmappnCosTgRowUsr3Min  
  INTEGER as ibmappnCosTgRowUsr3Max  

IbmappnIsInEntry  
SEQUENCE    
  DisplayString as ibmappnIsInFqLuName  
  OCTET STRING as ibmappnIsInPcid  
  DisplayString as ibmappnIsInPriLuName  
  DisplayString as ibmappnIsInSecLuName  
  DisplayString as ibmappnIsInModeName  
  DisplayString as ibmappnIsInCosName  
  INTEGER as ibmappnIsInTransPriority  
  INTEGER as ibmappnIsInSessType  
  INTEGER as ibmappnIsInSessState  
  TimeTicks as ibmappnIsInSessStartTime  
  TimeTicks as ibmappnIsInSessUpTime  
  TimeTicks as ibmappnIsInCtrUpTime  
  Counter as ibmappnIsInP2SFmdPius  
  Counter as ibmappnIsInS2PFmdPius  
  Counter as ibmappnIsInP2SNonFmdPius  
  Counter as ibmappnIsInS2PNonFmdPius  
  Counter as ibmappnIsInP2SFmdBytes  
  Counter as ibmappnIsInS2PFmdBytes  
  Counter as ibmappnIsInP2SNonFmdBytes  
  Counter as ibmappnIsInS2PNonFmdBytes  
  DisplayString as ibmappnIsInPsAdjCpName  
  INTEGER as ibmappnIsInPsAdjTgNum  
  INTEGER as ibmappnIsInPsSendMaxBtuSize  
  INTEGER as ibmappnIsInPsSendPacingType  
  Gauge as ibmappnIsInPsSendRpc  
  Gauge as ibmappnIsInPsSendNxWndwSize  
  INTEGER as ibmappnIsInPsRecvPacingType  
  Gauge as ibmappnIsInPsRecvRpc  
  Gauge as ibmappnIsInPsRecvNxWndwSize  
  DisplayString as ibmappnIsInSsAdjCpName  
  INTEGER as ibmappnIsInSsAdjTgNum  
  INTEGER as ibmappnIsInSsSendMaxBtuSize  
  INTEGER as ibmappnIsInSsSendPacingType  
  Gauge as ibmappnIsInSsSendRpc  
  Gauge as ibmappnIsInSsSendNxWndwSize  
  INTEGER as ibmappnIsInSsRecvPacingType  
  Gauge as ibmappnIsInSsRecvRpc  
  Gauge as ibmappnIsInSsRecvNxWndwSize  
  OCTET STRING as ibmappnIsInRouteInfo  

IbmappnIsAcBtypeEntry  
SEQUENCE    
  INTEGER as ibmappnIsAcBtypeMedia  
  INTEGER as ibmappnIsAcBtypeActive  
  DisplayString as ibmappnIsAcBtypeDirName  
  INTEGER as ibmappnIsAcBtypePrdMaxBufs  
  INTEGER as ibmappnIsAcBtypeMaxBufs  
  Gauge as ibmappnIsAcBtypeCurBufs  
  INTEGER as ibmappnIsAcBtypePrdRecPerBuf  
  INTEGER as ibmappnIsAcBtypeRecPerBuf  
  INTEGER as ibmappnIsAcBtypeRecFormat  
  INTEGER as ibmappnIsAcBtypeFullAction  
  TimeTicks as ibmappnIsAcBtypeFullTime  
  INTEGER as ibmappnIsAcBtypeFullReason  
  INTEGER as ibmappnIsAcBtypeFullWraps  
  INTEGER as ibmappnIsAcBtypeFullLosts  
  INTEGER as ibmappnIsAcBtypeErrorWraps  
  INTEGER as ibmappnIsAcBtypeErrorLosts  
  INTEGER as ibmappnIsAcBtypeCheckPts  
  INTEGER as ibmappnIsAcBtypePurges  
  INTEGER as ibmappnIsAcBtypeDeletes  
  INTEGER as ibmappnIsAcBtypeResets  
  INTEGER as ibmappnIsAcBtypeClearStats  

IbmappnIsAcBufEntry  
SEQUENCE    
  INTEGER as ibmappnIsAcBufMedia  
  INTEGER as ibmappnIsAcBufNumber  
  INTEGER as ibmappnIsAcBufState  
  INTEGER as ibmappnIsAcBufRecFormat  
  INTEGER as ibmappnIsAcBufMaxRecords  
  INTEGER as ibmappnIsAcBufOldestIndex  
  INTEGER as ibmappnIsAcBufNewestIndex  
  DisplayString as ibmappnIsAcBufName  

IbmappnIsAcTimeEntry  
SEQUENCE    
  INTEGER as ibmappnIsAcTimeIndex  
  INTEGER as ibmappnIsAcTimeEntryType  
  INTEGER as ibmappnIsAcTimeForMedia  
  TimeTicks as ibmappnIsAcTimeRecTime  
  INTEGER as ibmappnIsAcTimeAgtUtcSecs  
  INTEGER as ibmappnIsAcTimeAgtUtcMins  
  INTEGER as ibmappnIsAcTimeAgtUtcHours  
  INTEGER as ibmappnIsAcTimeAgtUtcMdays  
  INTEGER as ibmappnIsAcTimeAgtUtcMonths  
  INTEGER as ibmappnIsAcTimeAgtUtcYears  
  INTEGER as ibmappnIsAcTimeAgtUtcWdays  
  INTEGER as ibmappnIsAcTimeAgtUtcYdays  
  INTEGER as ibmappnIsAcTimeAgtUtcIsdst  
  DisplayString as ibmappnIsAcTimeAgtName  
  INTEGER as ibmappnIsAcTimeMgrUtcSecs  
  INTEGER as ibmappnIsAcTimeMgrUtcMins  
  INTEGER as ibmappnIsAcTimeMgrUtcHours  
  INTEGER as ibmappnIsAcTimeMgrUtcMdays  
  INTEGER as ibmappnIsAcTimeMgrUtcMonths  
  INTEGER as ibmappnIsAcTimeMgrUtcYears  
  INTEGER as ibmappnIsAcTimeMgrUtcWdays  
  INTEGER as ibmappnIsAcTimeMgrUtcYdays  
  INTEGER as ibmappnIsAcTimeMgrUtcIsdst  
  DisplayString as ibmappnIsAcTimeMgrName  
  INTEGER as ibmappnIsAcTimeMgrTimeValid  

IbmappnIsAcDataEntry  
SEQUENCE    
  INTEGER as ibmappnIsAcIndex  
  INTEGER as ibmappnIsAcEntryType  
  TimeTicks as ibmappnIsAcRecTime  
  DisplayString as ibmappnIsAcFqLuName  
  OCTET STRING as ibmappnIsAcPcid  
  DisplayString as ibmappnIsAcPriLuName  
  DisplayString as ibmappnIsAcSecLuName  
  DisplayString as ibmappnIsAcCosName  
  DisplayString as ibmappnIsAcModeName  
  INTEGER as ibmappnIsAcTransPriority  
  INTEGER as ibmappnIsAcSessType  
  INTEGER as ibmappnIsAcSessState  
  TimeTicks as ibmappnIsAcSessStartTime  
  TimeTicks as ibmappnIsAcSessUpTime  
  TimeTicks as ibmappnIsAcCtrUpTime  
  OCTET STRING as ibmappnIsAcEndReason  
  Counter as ibmappnIsAcP2SFmdPius  
  Counter as ibmappnIsAcS2PFmdPius  
  Counter as ibmappnIsAcP2SNonFmdPius  
  Counter as ibmappnIsAcS2PNonFmdPius  
  Counter as ibmappnIsAcP2SFmdBytes  
  Counter as ibmappnIsAcS2PFmdBytes  
  Counter as ibmappnIsAcP2SNonFmdBytes  
  Counter as ibmappnIsAcS2PNonFmdBytes  
  OCTET STRING as ibmappnIsAcRouteInfo  

IbmappcInLluEntry  
SEQUENCE    
  DisplayString as ibmappcInLluLuName  
  INTEGER as ibmappcInLluDefType  
  INTEGER as ibmappcInLluSessLimit  
  INTEGER as ibmappcInLluBindRspMayQ  
  INTEGER as ibmappcInLluDefaultLu  
  INTEGER as ibmappcInLluCntlPtLu  
  Gauge as ibmappcInLluCurActSess  

IbmappcInRluEntry  
SEQUENCE    
  DisplayString as ibmappcInRluLocLuName  
  DisplayString as ibmappcInRluParLuName  
  DisplayString as ibmappcInRluParLuLocName  
  INTEGER as ibmappcInRluDefType  
  INTEGER as ibmappcInRluDefParaSessSup  
  INTEGER as ibmappcInRluDefCnosSup  
  INTEGER as ibmappcInRluDefAllVerSup  
  INTEGER as ibmappcInRluDefAttSecSup  
  INTEGER as ibmappcInRluDefSessSecSup  
  INTEGER as ibmappcInRluDefEnhanSecSup  
  INTEGER as ibmappcInRluActType  
  INTEGER as ibmappcInRluActParaSessSup  
  INTEGER as ibmappcInRluActCnosSup  
  INTEGER as ibmappcInRluActAllVerSup  
  INTEGER as ibmappcInRluActAttSecSup  
  INTEGER as ibmappcInRluActSessSecSup  
  INTEGER as ibmappcInRluActEnhanSecSup  

IbmappcInMdEntry  
SEQUENCE    
  DisplayString as ibmappcInMdLluName  
  DisplayString as ibmappcInMdRluName  
  DisplayString as ibmappcInMdModeName  
  INTEGER as ibmappcInMdDefType  
  DisplayString as ibmappcInMdSessEndTpName  
  INTEGER as ibmappcInMdSessLimit  
  INTEGER as ibmappcInMdMaxSessLimit  
  INTEGER as ibmappcInMdAutoActLimit  
  INTEGER as ibmappcInMdDrainSelf  
  INTEGER as ibmappcInMdDrainPart  
  INTEGER as ibmappcInMdMinCwinLimit  
  INTEGER as ibmappcInMdMinClosLimit  
  INTEGER as ibmappcInMdRecvPacWinSz  
  INTEGER as ibmappcInMdSendPacWinSz  
  INTEGER as ibmappcInMdPrefRecvRuSz  
  INTEGER as ibmappcInMdPrefSendRuSz  
  INTEGER as ibmappcInMdRecvRuSzUpBnd  
  INTEGER as ibmappcInMdSendRuSzUpBnd  
  INTEGER as ibmappcInMdRecvRuSzLoBnd  
  INTEGER as ibmappcInMdSendRuSzLoBnd  
  INTEGER as ibmappcInMdDfSyncLvl  
  INTEGER as ibmappcInMdAcSyncLvl  
  INTEGER as ibmappcInMdDfCrypto  
  INTEGER as ibmappcInMdAcCrypto  
  INTEGER as ibmappcInMdReinit  
  INTEGER as ibmappcInMdAltCode  
  Gauge as ibmappcInMdActCwin  
  Gauge as ibmappcInMdActClos  
  Gauge as ibmappcInMdPndCwin  
  Gauge as ibmappcInMdPndClos  
  Gauge as ibmappcInMdPtmCwin  
  Gauge as ibmappcInMdPtmClos  
  Gauge as ibmappcInMdFreeSessLst  
  Gauge as ibmappcInMdWaitReqLst  

IbmappcInLtpEntry  
SEQUENCE    
  DisplayString as ibmappcInLtpLuName  
  DisplayString as ibmappcInLtpTpName  
  INTEGER as ibmappcInLtpDefType  
  INTEGER as ibmappcInLtpSyncLvl  
  INTEGER as ibmappcInLtpInstLmt  
  Gauge as ibmappcInLtpInstNum  
  INTEGER as ibmappcInLtpStatus  
  INTEGER as ibmappcInLtpLongRun  
  INTEGER as ibmappcInLtpPfCnos  
  INTEGER as ibmappcInLtpPfSessCntl  
  INTEGER as ibmappcInLtpPfDefine  
  INTEGER as ibmappcInLtpPfDisplay  
  INTEGER as ibmappcInLtpPfAllocSer  
  INTEGER as ibmappcInLtpRescSup  
  INTEGER as ibmappcInLtpRecoSup  
  INTEGER as ibmappcInLtpSecReq  
  INTEGER as ibmappcInLtpSecLvl  
  INTEGER as ibmappcInLtpVerPip  
  INTEGER as ibmappcInLtpPipSubNum  

IbmappcInSsEntry  
SEQUENCE    
  DisplayString as ibmappcInSsFqLuName  
  OCTET STRING as ibmappcInSsPcid  
  DisplayString as ibmappcInSsPluName  
  DisplayString as ibmappcInSsSluName  
  DisplayString as ibmappcInSsModeName  
  DisplayString as ibmappcInSsCosName  
  INTEGER as ibmappcInSsSessType  
  INTEGER as ibmappcInSsSessState  
  INTEGER as ibmappcInSsTransPriority  
  INTEGER as ibmappcInSsPaceType  
  INTEGER as ibmappcInSsSendMaxRuSz  
  INTEGER as ibmappcInSsRecvMaxRuSz  
  INTEGER as ibmappcInSsEnhanceSecSup  
  INTEGER as ibmappcInSsSendPacingType  
  Gauge as ibmappcInSsSendRpc  
  Gauge as ibmappcInSsSendNxWndwSize  
  INTEGER as ibmappcInSsRecvPacingType  
  Gauge as ibmappcInSsRecvRpc  
  Gauge as ibmappcInSsRecvNxWndwSize  
  TimeTicks as ibmappcInSsSessStartTime  
  TimeTicks as ibmappcInSsSessUpTime  
  TimeTicks as ibmappcInSsCtrUpTime  
  Counter as ibmappcInSsP2SFmdPius  
  Counter as ibmappcInSsS2PFmdPius  
  Counter as ibmappcInSsP2SNonFmdPius  
  Counter as ibmappcInSsS2PNonFmdPius  
  Counter as ibmappcInSsP2SFmdBytes  
  Counter as ibmappcInSsS2PFmdBytes  
  Counter as ibmappcInSsP2SNonFmdBytes  
  Counter as ibmappcInSsS2PNonFmdBytes  
  OCTET STRING as ibmappcInSsRscv  

IbmappcInSsStatusEntry  
SEQUENCE    
  INTEGER as ibmappcInSsStatusIndex  
  TimeTicks as ibmappcInSsStatusTime  
  INTEGER as ibmappcInSsStatusType  
  DisplayString as ibmappcInSsStatusLocLuName  
  DisplayString as ibmappcInSsStatusParLuName  
  DisplayString as ibmappcInSsStatusModeName  
  OCTET STRING as ibmappcInSsStatusUnbindType  
  OCTET STRING as ibmappcInSsStatusSenseCode  
  DisplayString as ibmappcInSsStatusComponentId  
  DisplayString as ibmappcInSsStatusDetectModule