
IRM3-MIB
File:
IRM3-MIB.mib (98395 bytes)
Imported modules
Imported symbols
Defined Objects
| device |
1.3.6.1.4.1.52.1.2.1.1 |
| OBJECT IDENTIFIER |
|
|
|
| deviceMMACType |
1.3.6.1.4.1.52.1.2.1.1.2 |
| Indicates the type of MMAC. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
unknown(1), mMAC8(2), mMAC5(3), mMAC3(4), mINIMMAC(5), mRXI(6), m3Shunt(7), m5Shunt(8), m8FNB(9), nonFNB(10), mMAC3Shunting(11), mMAC5Shunting(12), mMAC8Shunting(13), m8Shunting(14) |
|
| deviceSlots |
1.3.6.1.4.1.52.1.2.1.1.3 |
| Number of available device slots in this device, including the IRM slot. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| deviceOccupiedSlots |
1.3.6.1.4.1.52.1.2.1.1.4 |
| The slots that contain MIM boards. This field is bit encoded (eg. if a bit is set then that board is present). For example, a value of 3 indicates that there are boards in the IRM slot and the first MIM slot. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| deviceDiscover |
1.3.6.1.4.1.52.1.2.1.1.21 |
| When this variable is set to 1 The following events occur: (1) The device sends a LINK-UP trap (2) The device sends a proprietary packet that will cause all other Cabeltron devices on that local network to send a LINK-UP trap. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| deviceTimeBase |
1.3.6.1.4.1.52.1.2.1.1.24 |
| The number of seconds used as the interval for performing all of the rate alarm checks. The minimum is 10 secs. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| deviceSrcAddrAgingTime |
1.3.6.1.4.1.52.1.2.1.1.26 |
| The number of minutes that a source address is not detected before it is removed from the source address table. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| deviceSrcAddrLocked |
1.3.6.1.4.1.52.1.2.1.1.28 |
| If this is set to 2, any source addresses that are detected on station ports that are not in the table will cause the port to be turned off. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
lockOff(1), lockOn(2) |
|
| deviceEtherOccupiedSlots |
1.3.6.1.4.1.52.1.2.1.1.29 |
| The slots that contain Ethernet MIM boards. This field is bit encoded (eg. if a bit is set then that board is present). For example, a value of 2 indicates that there is an Ethernet board in the first MIM slot. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| deviceTROccupiedSlots |
1.3.6.1.4.1.52.1.2.1.1.30 |
| The slots that contain managable Token Ring MIM boards. This field is bit encoded (eg. if a bit is set then that board is present). For example, a value of 2 indicates that there is a managable Token Ring board in the first MIM slot. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| deviceFDDIOccupiedSlots |
1.3.6.1.4.1.52.1.2.1.1.31 |
| The slots that contain FDDI MIM boards. This field is bit encoded (eg. if a bit is set then that board is present). For example, a value of 2 indicates that there is an FDDI board in the first MIM slot. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| deviceRestoreDefaults |
1.3.6.1.4.1.52.1.2.1.1.32 |
| If this object is set to 1 the factory defaults are restored. This, however, does not affect the device's IP address. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| deviceOtherFrames |
1.3.6.1.4.1.52.1.2.1.1.42 |
| The number of frames seen by this device, that do not fall into any of the previously listed protocol catagories. |
| OBJECT-TYPE |
|
|
|
| |
Counter |
|
|
| deviceThdPartyOccupiedSlots |
1.3.6.1.4.1.52.1.2.1.1.51 |
| The slots that contain Third Party MIM boards. This field is bit encoded (eg. if a bit is set then that board is present). For example, a value of 2 indicates that there is a Third Party board in the first MIM slot. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| deviceImimOccupiedSlots |
1.3.6.1.4.1.52.1.2.1.1.52 |
| The slots that contain Cabletron Intelligent MIM boards. This field is bit encoded (eg. if a bit is set then that board is present). For example, a value of 2 indicates that there is an Intelligent board in the first MIM slot. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| ctIPDefaultFrameType |
1.3.6.1.4.1.52.1.2.1.1.56 |
| Defines the default frame type that will be used by the device. A device will understand both frame types and will respond based upon the framing type that is learned for the given address. This object defines the type of framing that will be used if no framing is known, for example ARP requests. Setting a value of 8022snap(2) will result in framing 802.3 - 802.2 - IP packets being generated by default. Setting a value of ethernet(1) will result in framing ethernet IP packets by default. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
ethernet(1), snap8022(2) |
|
| deviceSrcAddrType |
1.3.6.1.4.1.52.1.2.1.1.57 |
| Selects the hashing algorithm of source addresses, DEC or IP |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
ipHash(1), decHash(2) |
|
| board |
1.3.6.1.4.1.52.1.2.1.2 |
| OBJECT IDENTIFIER |
|
|
|
| port |
1.3.6.1.4.1.52.1.2.1.3 |
| OBJECT IDENTIFIER |
|
|
|
| sourceAddr |
1.3.6.1.4.1.52.1.2.1.7 |
| OBJECT IDENTIFIER |
|
|
|
| sourceAddrBoard |
1.3.6.1.4.1.52.1.2.1.7.1 |
| The board number of the port that the supplied source address has been found on. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| sourceAddrPort |
1.3.6.1.4.1.52.1.2.1.7.2 |
| The port number of the port that the supplied source address has been found on. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| redundancy |
1.3.6.1.4.1.52.1.2.1.8 |
| OBJECT IDENTIFIER |
|
|
|
| redundancyRetryCount |
1.3.6.1.4.1.52.1.2.1.8.5 |
| The number of unanswered polls allowed for the indicated circuit before the current connection is declared bad. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| redundancyNumBPs |
1.3.6.1.4.1.52.1.2.1.8.6 |
| The number of board/port combinations associated with the indicated circuit. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| redundancyCircuitReset |
1.3.6.1.4.1.52.1.2.1.8.15 |
| Reset the indicated circuit. Return all of the associated board and ports to NOT-USED, remove associated addresses from the polling list, reset the circuit name and retry count to default values. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
reset(1) |
|
| alarm |
1.3.6.1.4.1.52.1.2.1.9 |
| OBJECT IDENTIFIER |
|
|
|
| devAlrm |
1.3.6.1.4.1.52.1.2.1.9.1 |
| OBJECT IDENTIFIER |
|
|
|
| devTraffic |
1.3.6.1.4.1.52.1.2.1.9.1.1 |
| OBJECT IDENTIFIER |
|
|
|
| devTrafficEnable |
1.3.6.1.4.1.52.1.2.1.9.1.1.1 |
| Enable the sending of device level traffic traps. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| devTrafficThreshold |
1.3.6.1.4.1.52.1.2.1.9.1.1.2 |
| The threshold of packets within the Devicetimebase that will cause a traffic alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| devColls |
1.3.6.1.4.1.52.1.2.1.9.1.2 |
| OBJECT IDENTIFIER |
|
|
|
| devCollsEnable |
1.3.6.1.4.1.52.1.2.1.9.1.2.1 |
| Enable the sending of device level collision alarms. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| devCollsThreshold |
1.3.6.1.4.1.52.1.2.1.9.1.2.2 |
| This object represents the number of collisions per good packet measured by the device that will generate an alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..15 |
|
| devError |
1.3.6.1.4.1.52.1.2.1.9.1.3 |
| OBJECT IDENTIFIER |
|
|
|
| devErrorEnable |
1.3.6.1.4.1.52.1.2.1.9.1.3.1 |
| Enable the sending of device level error alarms. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| devErrorThreshold |
1.3.6.1.4.1.52.1.2.1.9.1.3.2 |
| This object represents the percentage of errors per good packet that will generate an alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| devErrorSource |
1.3.6.1.4.1.52.1.2.1.9.1.3.3 |
| The type of error used for the error alarm. The integer is a bit encoded version of which errors to include in the error sum. The bits are encoded as follows: CRCErrors - Bit 0 - Least Significant Bit runts - Bit 1 OOWColls - Bit 2 alignErrs - Bit 3 NoResource - Bit 4 Giants - Bit 5 |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| devBroad |
1.3.6.1.4.1.52.1.2.1.9.1.4 |
| OBJECT IDENTIFIER |
|
|
|
| devBroadEnable |
1.3.6.1.4.1.52.1.2.1.9.1.4.1 |
| Enable the sending of device level broadcast traps. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| devBroadThreshold |
1.3.6.1.4.1.52.1.2.1.9.1.4.2 |
| The threshold of broadcast packets within the Devicetimebase that will cause a broadcast alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| bdAlrm |
1.3.6.1.4.1.52.1.2.1.9.2 |
| OBJECT IDENTIFIER |
|
|
|
| bdTraffic |
1.3.6.1.4.1.52.1.2.1.9.2.1 |
| OBJECT IDENTIFIER |
|
|
|
| bdTrafficEnable |
1.3.6.1.4.1.52.1.2.1.9.2.1.1 |
| Enable the sending of board level traffic traps for this board. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| bdTrafficThreshold |
1.3.6.1.4.1.52.1.2.1.9.2.1.2 |
| The threshold of packets within the Devicetimebase that will cause a traffic alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| bdTrafficBdDisable |
1.3.6.1.4.1.52.1.2.1.9.2.1.3 |
| Permit a board to be disabled on a traffic threshold alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| bdColls |
1.3.6.1.4.1.52.1.2.1.9.2.2 |
| OBJECT IDENTIFIER |
|
|
|
| bdCollsEnable |
1.3.6.1.4.1.52.1.2.1.9.2.2.1 |
| Enable the sending of board level collision alarms. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| bdCollsThreshold |
1.3.6.1.4.1.52.1.2.1.9.2.2.2 |
| This object represents the number of collisions per good packet measured by the board that will generate an alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..15 |
|
| bdCollsBdDisable |
1.3.6.1.4.1.52.1.2.1.9.2.2.3 |
| Permit a board to be disabled on a collision threshold alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| bdError |
1.3.6.1.4.1.52.1.2.1.9.2.3 |
| OBJECT IDENTIFIER |
|
|
|
| bdErrorEnable |
1.3.6.1.4.1.52.1.2.1.9.2.3.1 |
| Enable the sending of board level error alarms. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| bdErrorThreshold |
1.3.6.1.4.1.52.1.2.1.9.2.3.2 |
| This object represents the percentage of errors per good packet that will generate an alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| bdErrorSource |
1.3.6.1.4.1.52.1.2.1.9.2.3.3 |
| The type of error used for the error alarm. The integer is a bit encoded version of which errors to include in the error sum. The bits are encoded as follows: CRCErrors - Bit 0 Least Significant Bit runts - Bit 1 OOWColls - Bit 2 alignErrs - Bit 3 NoResource - Bit 4 Giants - Bit 5 |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| bdErrorBdDisable |
1.3.6.1.4.1.52.1.2.1.9.2.3.4 |
| Permit a board to be disabled on an error threshold alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| bdBroad |
1.3.6.1.4.1.52.1.2.1.9.2.4 |
| OBJECT IDENTIFIER |
|
|
|
| bdBroadEnable |
1.3.6.1.4.1.52.1.2.1.9.2.4.1 |
| Enable the sending of board level broadcast traps for this board. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| bdBroadThreshold |
1.3.6.1.4.1.52.1.2.1.9.2.4.2 |
| The threshold of broadcast packets within the Devicetimebase that will cause a broadcast alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| bdBroadDisable |
1.3.6.1.4.1.52.1.2.1.9.2.4.3 |
| Permit a board to be disabled on a broadcast threshold alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| portAlrm |
1.3.6.1.4.1.52.1.2.1.9.3 |
| OBJECT IDENTIFIER |
|
|
|
| portTraffic |
1.3.6.1.4.1.52.1.2.1.9.3.1 |
| OBJECT IDENTIFIER |
|
|
|
| portTrafficEnable |
1.3.6.1.4.1.52.1.2.1.9.3.1.1 |
| Enable the sending of port level traffic traps for this port. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| portColls |
1.3.6.1.4.1.52.1.2.1.9.3.2 |
| OBJECT IDENTIFIER |
|
|
|
| portCollsEnable |
1.3.6.1.4.1.52.1.2.1.9.3.2.1 |
| Enable the sending of port level collsion alarms. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| portCollsThreshold |
1.3.6.1.4.1.52.1.2.1.9.3.2.2 |
| This object represents the number of collisions per good packet measured by the port that will generate an alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..15 |
|
| portError |
1.3.6.1.4.1.52.1.2.1.9.3.3 |
| OBJECT IDENTIFIER |
|
|
|
| portErrorEnable |
1.3.6.1.4.1.52.1.2.1.9.3.3.1 |
| Enable the sending of port level error alarms. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| portErrorThreshold |
1.3.6.1.4.1.52.1.2.1.9.3.3.2 |
| This object represents the percentage of errors per good packet that will generate an alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| portErrorSource |
1.3.6.1.4.1.52.1.2.1.9.3.3.3 |
| The type of error used for the error alarm. The integer is a bit encoded version of which errors to include in the error sum. The bits are encoded as follows: CRCErrors - Bit 0 - Least Significant Bit runts - Bit 1 OOWColls - Bit 2 alignErrs - Bit 3 NoResource - Bit 4 Giants - Bit 5 |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| portBroad |
1.3.6.1.4.1.52.1.2.1.9.3.4 |
| OBJECT IDENTIFIER |
|
|
|
| portBroadEnable |
1.3.6.1.4.1.52.1.2.1.9.3.4.1 |
| Enable the sending of port level broadcast alarms. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| portBroadThreshold |
1.3.6.1.4.1.52.1.2.1.9.3.4.2 |
| The threshold of broadcast packets within the Devicetimebase that will cause a broadcast alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| portBroadDisable |
1.3.6.1.4.1.52.1.2.1.9.3.4.3 |
| Permit a port to be disabled on a broadcast threshold alarm. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disable(1), enable(2) |
|
| deviceR2 |
1.3.6.1.4.1.52.1.2.2.1 |
| OBJECT IDENTIFIER |
|
|
|
| tokenRingD |
1.3.6.1.4.1.52.1.2.2.1.3 |
| OBJECT IDENTIFIER |
|
|
|
| deviceTRPorts |
1.3.6.1.4.1.52.1.2.2.1.3.2 |
| This gives the total number of Token Ring ports on this device. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| deviceTRLans |
1.3.6.1.4.1.52.1.2.2.1.3.5 |
| This gives the number of Token Rings formed on this device. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| deviceTRBoardMap |
1.3.6.1.4.1.52.1.2.2.1.3.7 |
| The slots that contain Token Ring MIM boards. This field is bit encoded (eg. if a bit is set then that board is present). For example, a value of 2 indicates that there is a Token Ring board in the first MIM slot. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| networkR2 |
1.3.6.1.4.1.52.1.2.2.2 |
| OBJECT IDENTIFIER |
|
|
|
| boardR2 |
1.3.6.1.4.1.52.1.2.2.3 |
| OBJECT IDENTIFIER |
|
|
|
| commonB |
1.3.6.1.4.1.52.1.2.2.3.1 |
| OBJECT IDENTIFIER |
|
|
|
| boardType |
1.3.6.1.4.1.52.1.2.2.3.1.3 |
| The type of the MIM. (eg. FOT, TPT, etc). See appendix A for encoding. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| boardStatus |
1.3.6.1.4.1.52.1.2.2.3.1.5 |
| The administrative status of this MIM. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disabled(1), enabled(2) |
|
| boardOper |
1.3.6.1.4.1.52.1.2.2.3.1.7 |
| Returns a value indicating whether any of the enabled ports on the board are not operational, thereby placing the board in a non-operational state. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
operational(1), notOperational(2) |
|
| ethernetB |
1.3.6.1.4.1.52.1.2.2.3.2 |
| OBJECT IDENTIFIER |
|
|
|
| boardOtherFrames |
1.3.6.1.4.1.52.1.2.2.3.2.20 |
| The number of frames seen by this board, that do not fall into any of the previously listed protocol catagories. |
| OBJECT-TYPE |
|
|
|
| |
Counter |
|
|
| boardSrcAddrLocked |
1.3.6.1.4.1.52.1.2.2.3.2.31 |
| If this is set to 2, any source addresses that are detected on station port that are not in the table will cause the port to be turned off. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
lockOff(1), lockOn(2) |
|
| tokenRingB |
1.3.6.1.4.1.52.1.2.2.3.3 |
| OBJECT IDENTIFIER |
|
|
|
| boardModeStatus |
1.3.6.1.4.1.52.1.2.2.3.3.3 |
| This describes the mode of this board. autoMode means the board is using the hardware defaults. mgmtMode means the board is using setting by the user. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
mgmtMode(1), autoMOde(2) |
|
| boardSpeed |
1.3.6.1.4.1.52.1.2.2.3.3.6 |
| The speed of the board. The board will expect to receive data at this speed. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
fourMHz(4), sixteenMhz(16) |
|
| ringSpeedFault |
1.3.6.1.4.1.52.1.2.2.3.3.7 |
| Data speed of station mismatches configuration speed of board. Board is automatically bypassed. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
noFaultDetected(1), faultDetected(2) |
|
| boardSpeedFaultPort |
1.3.6.1.4.1.52.1.2.2.3.3.8 |
| This object indicates which ring speed detect circuit(s) caused the fault, if there was one. The return code indicates the location on the board feeding the speed detect circuit(s). Ring in means the circuit on the back-up path between the ring out port and the ring in port. FNB means the circuit between the ring in port and the FNB. NotApplicable means that a ring Speed Fault has not occurred. Since more than one circuit can cause the fault, the return code is the sum of the following values: 1 - FNB 2 - RingIn 4 - RingOut 8 - NotApplicable |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| boardFirstRingPort |
1.3.6.1.4.1.52.1.2.2.3.3.9 |
| This object defines which port on the board is the first ring port. All ring port numbers will be consecutive. Using this in conjunction with BoardRingPorts, all ring port numbers can be determined. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| boardBypassRingPortState |
1.3.6.1.4.1.52.1.2.2.3.3.10 |
| This object sets and reports the state of the ring bypass relay on boards which contain a ring bypass relay. The ring bypass relay will separate only the ring ports from the FNB. The FNB only bypasses the station ports on these boards. The illegal value (3) will return an error status if set. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
off(1), on(2), illegal(3) |
|
| fDDIB |
1.3.6.1.4.1.52.1.2.2.3.4 |
| OBJECT IDENTIFIER |
|
|
|
| portR2 |
1.3.6.1.4.1.52.1.2.2.4 |
| OBJECT IDENTIFIER |
|
|
|
| commonP |
1.3.6.1.4.1.52.1.2.2.4.1 |
| OBJECT IDENTIFIER |
|
|
|
| portOper |
1.3.6.1.4.1.52.1.2.2.4.1.5 |
| Returns a value indicating whether this port is in an operational state. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
notOperational(1), operational(2) |
|
| ethernetP |
1.3.6.1.4.1.52.1.2.2.4.2 |
| OBJECT IDENTIFIER |
|
|
|
| portLinkStatus |
1.3.6.1.4.1.52.1.2.2.4.2.2 |
| The state of the link signal for this port. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
linkSignalInactive(1), linkSignalActive(2), linkSignalNotSupported(3) |
|
| portStatus |
1.3.6.1.4.1.52.1.2.2.4.2.3 |
| The network state of this port. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
active(1), segmented(2) |
|
| portRedundType |
1.3.6.1.4.1.52.1.2.2.4.2.16 |
| The type of port this port is in the redundant circuit. The port must be associated with a redundant circuit first, using the object portRedundCrt. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
notUsed(1), primary(2), backup(3) |
|
| portRedundStatus |
1.3.6.1.4.1.52.1.2.2.4.2.17 |
| The current state of this port is in the redundant circuit. The port must be associated with a redundant circuit first, using the object portRedundCrt. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
notUsed(1), active(2), inactive(3) |
|
| portOtherFrames |
1.3.6.1.4.1.52.1.2.2.4.2.27 |
| The number of frames seen by this port, that do not fall into any of the previously listed protocol catagories. |
| OBJECT-TYPE |
|
|
|
| |
Counter |
|
|
| portSrcAddrLocked |
1.3.6.1.4.1.52.1.2.2.4.2.38 |
| If this is set to 2, any source addresses that are detected on station ports that are not in the table will cause the port to be turned off. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
lockOff(1), lockOn(2) |
|
| tokenRingP |
1.3.6.1.4.1.52.1.2.2.4.3 |
| OBJECT IDENTIFIER |
|
|
|
| stationP |
1.3.6.1.4.1.52.1.2.2.4.3.1 |
| OBJECT IDENTIFIER |
|
|
|
| stationPortLinkStatus |
1.3.6.1.4.1.52.1.2.2.4.3.1.1 |
| When station is supplying phantom current the Link Signal is active. When there is no phantom current the Link Signal is inactive. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
linkSignalInactive(1), linkSignalActive(2) |
|
| stationPortLinkStateTime |
1.3.6.1.4.1.52.1.2.2.4.3.1.2 |
| The amount of in seconds which have elapsed since the station port last changed state. Note: setting this to zero will clear the time. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| ringP |
1.3.6.1.4.1.52.1.2.2.4.3.2 |
| OBJECT IDENTIFIER |
|
|
|
| ringPort2 |
1.3.6.1.4.1.52.1.2.2.4.3.3 |
| OBJECT IDENTIFIER |
|
|
|
| commonRP |
1.3.6.1.4.1.52.1.2.2.4.3.3.1 |
| OBJECT IDENTIFIER |
|
|
|
| commonRPcapabilities |
1.3.6.1.4.1.52.1.2.2.4.3.3.1.1 |
| This object returns a code indicating that the queried ring port is nonautowrap, autowrap or selectable. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
nonAutowrap(1), autowrap(2), selectable(3) |
|
| autowrapRP |
1.3.6.1.4.1.52.1.2.2.4.3.3.2 |
| OBJECT IDENTIFIER |
|
|
|
| autowrapRPFaultStatus |
1.3.6.1.4.1.52.1.2.2.4.3.3.2.1 |
| This object reports the wire fault of an autowrappable ring port. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
faultUndetectable(1), noFaultDetected(2), faultDetected(3) |
|
| autowrapRPFaultStateTime |
1.3.6.1.4.1.52.1.2.2.4.3.3.2.2 |
| This object reports the amount of time in time ticks since the ring port fault state last changed. Writing zero to this object resets the time. If a zero is read, it means either zero time ticks have passed or the ring port is nonautowrap. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| autowrapRPSelectedType |
1.3.6.1.4.1.52.1.2.2.4.3.3.2.3 |
| This object indicates the media type of the indicated ring port on some boards. Some boards provide both STP and fiber optic ring ports. The unselectable value will return an error if set. A set of STP or FO for a non-selectable ring port will not do anything, i.e. the status of normal is returned. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
unselectable(1), stp(2), fo(3) |
|
| autowrapRPPhantomCurrent |
1.3.6.1.4.1.52.1.2.2.4.3.3.2.4 |
| This object tells the board to turn on phantom current for the ring port and look for wire faults. NoPhantomAvailable will return an error if set. A set of activatePhantom or deactivatePhantom for a non-autowrap ring port will not do anything, i.e. the status of normal is returned. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
noPhantomAvailable(1), activatePhantom(2), deactivatePhantom(3) |
|
| fDDIP |
1.3.6.1.4.1.52.1.2.2.4.4 |
| OBJECT IDENTIFIER |
|
|
|
| fNB |
1.3.6.1.4.1.52.1.6.1.1 |
| OBJECT IDENTIFIER |
|
|
|
| connectedLeft |
1.3.6.1.4.1.52.1.6.1.1.1 |
| The Connected Left board (board n + 1) has the following states: Detached == 1 (Management (only management) detached, read/write). Attached == 2 (Management/AutoMode attached, read/write). Faulted == 3 (Management/AutoMode tried to attach but failed READ ONLY). |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
detached(1), attached(2), faulted(3) |
|
| connectedRight |
1.3.6.1.4.1.52.1.6.1.1.2 |
| The Connected Right board (board n - 1) has the following states: Detached == 1 (Management (only management) detached, read/write). Attached == 2 (Management/AutoMode attached, read/write ). Faulted == 3 (Management/AutoMode tried to attach but failed READ ONLY). |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
detached(1), attached(2), faulted(3) |
|
| boardBypassState |
1.3.6.1.4.1.52.1.6.1.1.3 |
| This object indicates that the board is in the bypassed state when it is ON. Bypassed means the board is NOT attached to the FNB. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
off(1), on(2) |
|