
| RFC1155-SMI | RFC1213-MIB | RFC-1212 |
| ITOUCH-MIB |
| Counter | TimeTicks | Gauge |
| ifIndex | OBJECT-TYPE | iTouch |
| xLink | 1.3.6.1.4.1.33.24 | ||
| OBJECT IDENTIFIER | |||
| xLinkBasic | 1.3.6.1.4.1.33.24.1 | ||
| OBJECT IDENTIFIER | |||
| linkTable | 1.3.6.1.4.1.33.24.1.1 | ||
| A list of links. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LinkEntry | |||
| linkEntry | 1.3.6.1.4.1.33.24.1.1.1 | ||
| Link entry. | |||
| OBJECT-TYPE | |||
| LinkEntry | |||
| linkNoBuffers | 1.3.6.1.4.1.33.24.1.1.1.1 | ||
| The number of packets discarded because of lack of buffers. | |||
| OBJECT-TYPE | |||
| Counter | |||
| linkDelayExceeded | 1.3.6.1.4.1.33.24.1.1.1.2 | ||
| The number of packets discarded because they were held to long. | |||
| OBJECT-TYPE | |||
| Counter | |||
| linkOutputQFull | 1.3.6.1.4.1.33.24.1.1.1.3 | ||
| The number of packets discarded because the output queue was full. | |||
| OBJECT-TYPE | |||
| Counter | |||
| linkDownTime | 1.3.6.1.4.1.33.24.1.1.1.4 | ||
| Total number of seconds that the link has been down. | |||
| OBJECT-TYPE | |||
| Counter | |||
| linkDownCount | 1.3.6.1.4.1.33.24.1.1.1.5 | ||
| Number of times that the link has been down. | |||
| OBJECT-TYPE | |||
| Counter | |||
| linkDownLastStart | 1.3.6.1.4.1.33.24.1.1.1.6 | ||
| Value of sysUpTime when the link last went down. If the link is up the value is 0. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| linkStatus | 1.3.6.1.4.1.33.24.1.1.1.7 | ||
| The status of the link | |||
| OBJECT-TYPE | |||
| INTEGER | running1(7), initWaitDsr(128), initWait(129), running2(130), purgeWait(131), down(132), purging(133), loop(138), testSend(139), testReceive(140), testLoop(141), speedChange(143), disabled(145), badQuality(146) | ||
| linkLostBuffers | 1.3.6.1.4.1.33.24.1.1.1.8 | ||
| Number of packets discarded because of lost buffers | |||
| OBJECT-TYPE | |||
| Counter | |||
| linkResourceTable | 1.3.6.1.4.1.33.24.1.2 | ||
| A list of link resources. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LinkResourceEntry | |||
| linkResourceEntry | 1.3.6.1.4.1.33.24.1.2.1 | ||
| link entry. | |||
| OBJECT-TYPE | |||
| LinkResourceEntry | |||
| linkResourceType | 1.3.6.1.4.1.33.24.1.2.1.1 | ||
| The resource type. | |||
| OBJECT-TYPE | |||
| INTEGER | utilization(1), outputQueue(2) | ||
| linkResourceCurrent | 1.3.6.1.4.1.33.24.1.2.1.2 | ||
| The current percent of the resource used. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| linkResourceHigh | 1.3.6.1.4.1.33.24.1.2.1.3 | ||
| The highest percent of the resource used. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| linkResourceAverage | 1.3.6.1.4.1.33.24.1.2.1.4 | ||
| The average percent of the resource used. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| xWan | 1.3.6.1.4.1.33.24.3 | ||
| OBJECT IDENTIFIER | |||
| wanTable | 1.3.6.1.4.1.33.24.3.1 | ||
| A list of WANs. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| WanEntry | |||
| wanEntry | 1.3.6.1.4.1.33.24.3.1.1 | ||
| WAN entry. | |||
| OBJECT-TYPE | |||
| WanEntry | |||
| wanProtocol | 1.3.6.1.4.1.33.24.3.1.1.1 | ||
| Controls the protocol run on the link, changes ifType, typically to 'other'. | |||
| OBJECT-TYPE | |||
| INTEGER | xcp(2), fr(3), ppp(4), frlmi(5), fransi(6), frdcelmi(7), frdceansi(8), x25(9) | ||
| wanCompressionAdminStatus | 1.3.6.1.4.1.33.24.3.1.1.2 | ||
| Controls whether link compression will be run if the link is running the xyplex protocol. Auto will enable compression for links slower than 67000. | |||
| OBJECT-TYPE | |||
| INTEGER | noCompression(1), compress(2), auto(256) | ||
| wanMaxForwardDelay | 1.3.6.1.4.1.33.24.3.1.1.3 | ||
| The number of milliseconds that a packet may be held on the Wan link before it will be discarded. The value 0 indicates no limit. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..32000 | ||
| wanMaxMultiForwardDelay | 1.3.6.1.4.1.33.24.3.1.1.4 | ||
| The number of milliseconds that a multicast packet may be held on the Wan link before it will be discarded. The value 0 indicates no delay. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..32000 | ||
| wanAdminSpeed | 1.3.6.1.4.1.33.24.3.1.1.5 | ||
| The speed that the software should use for the wan link. The value 0 indicates that the measured speed should be used. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| wanCompressionOperStatus | 1.3.6.1.4.1.33.24.3.1.1.6 | ||
| If the link is running the Xyplex protocol, indicates whether link compression is running. | |||
| OBJECT-TYPE | |||
| INTEGER | notCompressing(1), compressing(2) | ||
| LinkEntry | |||
| SEQUENCE | |||
| Counter as linkNoBuffers | |||
| Counter as linkDelayExceeded | |||
| Counter as linkOutputQFull | |||
| Counter as linkDownTime | |||
| Counter as linkDownCount | |||
| TimeTicks as linkDownLastStart | |||
| INTEGER as linkStatus | |||
| Counter as linkLostBuffers | |||
| LinkResourceEntry | |||
| SEQUENCE | |||
| INTEGER as linkResourceType | |||
| Gauge as linkResourceCurrent | |||
| Gauge as linkResourceHigh | |||
| Gauge as linkResourceAverage | |||
| WanEntry | |||
| SEQUENCE | |||
| INTEGER as wanProtocol | |||
| INTEGER as wanCompressionAdminStatus | |||
| INTEGER as wanMaxForwardDelay | |||
| INTEGER as wanMaxMultiForwardDelay | |||
| INTEGER as wanAdminSpeed | |||
| INTEGER as wanCompressionOperStatus | |||