
| SNMPv2-SMI | SNMPv2-TC |
| NOTIFICATION-TYPE | MODULE-IDENTITY | OBJECT-TYPE |
| enterprises | IpAddress | MacAddress |
| DisplayString | RowStatus |
| luDload | 1.3.6.1.4.1.677 | ||
| Lucent Generic Download / Upload Private MIB | |||
| MODULE-IDENTITY | |||
| luOpTable | 1.3.6.1.4.1.677.1 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LuOpEntry | |||
| luOpEntry | 1.3.6.1.4.1.677.1.1 | ||
| Each entry in the LU Operations Table corresponds to a unique logical managed device. It is possible that a single HW device can have resident severial Logical managed devices. | |||
| OBJECT-TYPE | |||
| LuOpEntry | |||
| luOpSerialNumber | 1.3.6.1.4.1.677.1.1.1 | ||
| The identifier of the device. This is a unique number and in most cases maps directly to the base MAC address of the device. Otherwise any combination of characters up to 32 bytes long. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..32) | ||
| luOpMCodeVersion | 1.3.6.1.4.1.677.1.1.2 | ||
| Microcode version of the device. Stored in the format :- first Byte - not used 2nd Byte - microcode major version number 3rd Byte - microcode minor version number 4th Byte - microcode debug version number. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| luOpBCodeVersion | 1.3.6.1.4.1.677.1.1.3 | ||
| Bootcode version of the device and the hardware version. Stored in the format :- first Byte - hardware version number 2nd Byte - microcode major version number 3rd Byte - microcode minor version number 4th Byte - microcode debug version number. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| luOpMCodeFilename | 1.3.6.1.4.1.677.1.1.4 | ||
| Original filename for the microcode that has been downloaded to the device. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| luOpAdminStatus | 1.3.6.1.4.1.677.1.1.5 | ||
| The desired operating mode of the device. The mode can be changed by setting this object. If the device does not support the action it will return a bad value error. The behaviour of these states is device specific and some of the states may latch until the state is returned to normal. normal - standard operating mode / can be used to cancel a download or return the device from any latching state. reboot - force the device to reboot. The device will reboot into the version of flash identified by luOpDefaultFlashVersion. identify - force the device to identify itself by flashing lights. This state may latch. test - force the device to do a self test. This state may latch. erase-config - erase all configuration info erase-flash - erase the version of microcode stored in the flash bank identifed by luOpEraseFlashVersion. tftp-ip - force the device to start a TFTP download over IP tftp-ipx - force the device to start a TFTP download over IPX rpl-ipx - force the device to start a RPL download over IPX rpl-llc - force the device to start a RPL download over LLC halt - force the defice to shutdown ready for power off up-tftp-ip - force the device to start a TFTP upload over IP up-tftp-ipx - force the device to start a TFTP upload over IPX snapshot - force the device to take a snapshot of its current configuration and save it to the name specified by the luOpConfFileName object. snapshot-tftp - force the device to take a snapshot of its running configuration and tftp it to a server. startup-tftp - force the device to upload it's startup configuration to a tftp server. file-tftp - force the device to upload a configuration file (specified in the luOpConfFileName object ) to a tftp server. tftp-startup - force the device to download it's startup configuration from a tftp server. tftp-snapshot - force the device to download it's running configuration from a tftp server. tftp-start-snap - force the device to download it's running configuration & startup configuration from a tftp server. tftp-file - force the device to download a configuration file from a tftp server. snapshot-startup - force the device to take a snapshot of it's running configuration and save it as the startup configuration. file-snapshot - force the device to copy the file specified in the luOpConfFileName to it's running configuration file-startup - force the device to copy the file specified in the luOpConfFileName to it's startup configuration | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), reboot(2), identify(3), test(4), erase-config(5), erase-flash(6), tftp-ip(7), tftp-ipx(8), rpl-ipx(9), rpl-llc(10), halt(11), up-tftp-ip(12), up-tftp-ipx(13), snapshot(14), snapshot-tftp(15), startup-tftp(16), file-tftp(17), tftp-snapshot(18), tftp-startup(19), tftp-start-snap(20), tftp-file(21), snapshot-startup(22), file-snapshot(23), file-startup(24) | ||
| luOpOperStatus | 1.3.6.1.4.1.677.1.1.6 | ||
| The current operating mode of the device. normal - standard operating mode reboot - the device is rebooting identify - the device is identifying itself test - the device is performing a self-test downloading - the device is performing a download uploading - the device is performing an upload reading-config - the device is reading a configuration file NOTE:This variable is only available on devices that support version 1.2 or greater of the Box MIB | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), reboot(2), identify(3), test(4), downloading(5), uploading(6), reading-config(7) | ||
| luOpEraseFlashVersion | 1.3.6.1.4.1.677.1.1.7 | ||
| A valid version index for the bank of flash or a software component to erase when AdminStatus is set to erase-flash. NOTE:This variable is only available on devices that support version 1.2 or greater of the Box MIB | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| luOpDefaultFlashVersion | 1.3.6.1.4.1.677.1.1.8 | ||
| The version index of the default flash bank that a device will reboot into when a standard reboot is performed. NOTE:This variable is only available on devices that support version 1.2 or greater of the Box MIB | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| luOpConfFileName | 1.3.6.1.4.1.677.1.1.9 | ||
| This specifies the filename under which to store the current configuration. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| luOpIndex | 1.3.6.1.4.1.677.1.1.10 | ||
| OBJECT-TYPE | |||
| INTEGER | |||
| luDeviceTable | 1.3.6.1.4.1.677.2 | ||
| A table containing information for all downloadable locations in the device components in a device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LuDeviceEntry | |||
| luDeviceEntry | 1.3.6.1.4.1.677.2.1 | ||
| An entry containing information for a specific downloadable location in a device. | |||
| OBJECT-TYPE | |||
| LuDeviceEntry | |||
| luDeviceIndex | 1.3.6.1.4.1.677.2.1.1 | ||
| Index into the table. Note: To support backwards compatibility, the following restrictions apply to the assignment of luDeviceIndex values. luDeviceIndex value 1 -- flash device Bank A, luDeviceIndex value 2 -- flash device Bank B | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| luDeviceDescription | 1.3.6.1.4.1.677.2.1.2 | ||
| A string containing a textual description for the component identified by this entry. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| luDeviceLocation | 1.3.6.1.4.1.677.2.1.3 | ||
| A string containing a textual description of the location of the component identified by this entry. eg Flash Bank A Flash ROM Boot ROM Boot Bank A Base Hardware Hardware Module NvRam non-Volitile Ram storage | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| luDeviceNumber | 1.3.6.1.4.1.677.2.1.4 | ||
| Version number for the component. Stored in the format :- 1st Byte - major version number 2nd Byte - minor version number 3rd Byte - debug version number. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(3) | ||
| luDeviceType | 1.3.6.1.4.1.677.2.1.5 | ||
| The type of object that this table entry contains Location information for. flash : code image resident in flash OR the flash bank itself boot-fixed : the version of the fixed boot ROM. boot-updateable : the current version of boot ROM code where the code can be updated. hardware-fixed : Hardware that cannot be upgraded. hardware-upgradeable : a plug in card that can be changed. sw_running : code image that is currently running in RAM. sw_component : a subcomponent of the entire software. Can be resident in flash or ram. These items should be placed in the version table following the version of which they are a subcomponent. default-image: The default image. non-default-image: Other images. default-boot-loader: The default boot loader. non-default-boot-loader: Other boot loaders. unknown - unknown. nvram - non-volitile Ram | |||
| OBJECT-TYPE | |||
| INTEGER | flash(1), boot-fixed(2), boot-updateable(3), hardware-fixed(4), hardware-upgradeable(5), other(6), sw-running(7), sw-component(8), default-image(9), non-default-image(10), default-boot-loader(11), non-default-boot-loader(12), unknown(20), nvram(21) | ||
| luDeviceFileName | 1.3.6.1.4.1.677.2.1.6 | ||
| A string containing the file name of the component identified by this entry. Allows to rename a file. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| luDeviceCount | 1.3.6.1.4.1.677.3 | ||
| The number of entries in the Location table | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| luDownloadTable | 1.3.6.1.4.1.677.4 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LuDownloadEntry | |||
| luDownloadEntry | 1.3.6.1.4.1.677.4.1 | ||
| OBJECT-TYPE | |||
| LuDownloadEntry | |||
| luDownloadIPAddress | 1.3.6.1.4.1.677.4.1.1 | ||
| The IP address of the server to use for the download when using TFTP-IP | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| luDownloadIPGateway | 1.3.6.1.4.1.677.4.1.2 | ||
| The IP gateway to be used to access the server. If this variable is zero then use the default gateway in luOpIPGateway. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| luDownloadIPXAddress | 1.3.6.1.4.1.677.4.1.3 | ||
| The IPX address of the server to use for the download when using TFTP-IPX or RPL-IPX. The format of the address is = 12 bytes. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(12) | ||
| luDownloadNodeAddress | 1.3.6.1.4.1.677.4.1.4 | ||
| The Node address of the server to use for the download when using RPL-LLC | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| luDownloadFileName | 1.3.6.1.4.1.677.4.1.5 | ||
| The filename of the microcode to download. The maximum length of this string is device specific. If a string that is too long is written to this variable BAD VALUE will be returned. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| luDownloadDestination | 1.3.6.1.4.1.677.4.1.6 | ||
| The destination for the download. This will contain the luDeviceIndex for the download destination. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| luDownloadState | 1.3.6.1.4.1.677.4.1.7 | ||
| The current state of the download | |||
| OBJECT-TYPE | |||
| INTEGER | idle(1), tftp-waiting-ip(2), tftp-running-ip(3), tftp-waiting-ipx(4), tftp-running-ipx(5), waiting-xmodem(6), running-xmodem(7), rpl-waiting-ipx(8), rpl-running-ipx(9), rpl-waiting-llc(10), rpl-running-llc(11), reading-configuration(12) | ||
| luDownloadFailureCode | 1.3.6.1.4.1.677.4.1.8 | ||
| While a download is in progress this will always be 'no-error'. After a download is complete this indicates the success or failure of the download. If it is anything other than 'no-error' then 'luDownloadStatusText' will contain a textual description of the error. Error codes from 100 upwards are errors returned from a TFTP server. Errors below this are locally generated. Configuration files may return errors after download as a result of reading a config file into the system. conf-file-gen-err - General (unknown error) conf-file-parse-error - Reading of config file resulted in parsing errors. conf-file-exec-error - Reading of config file resulted in execution errors. | |||
| OBJECT-TYPE | |||
| INTEGER | no-error(1), config-error(2), busy(3), timeout(4), cancelled(5), incompatible-file(6), file-too-big(7), protocol-error(8), flash-write-error(9), nvram-write-error(10), conf-file-gen-err(11), conf-file-parse-error(12), conf-file-exec-error(13), undefined-error(100), file-not-found(101), access-violation(102), out-of-memory(103), illegal-operation(104), unknown-transfer-id(105), file-already-exists(106), no-such-user(107) | ||
| luDownloadStatusText | 1.3.6.1.4.1.677.4.1.9 | ||
| A display string describing the status of the download in progress, or the reason for failure of the last download. If FailureCode = no-error then StatusText may be empty. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| luDownloadSize | 1.3.6.1.4.1.677.4.1.10 | ||
| While a download is in progress this indicates the number of bytes transferred so far. After the download is completed this remains at the final size downloaded. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| luDownloadErrorLogName | 1.3.6.1.4.1.677.4.1.11 | ||
| The filename under which an error log has been created. In the case of file downloads that produce errors this file should contain a log of errors that occured | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| luDownloadErrorLogLocation | 1.3.6.1.4.1.677.4.1.12 | ||
| The location of the error log. This will contain the luDeviceIndex for the error log | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| luUploadTable | 1.3.6.1.4.1.677.5 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LuUploadEntry | |||
| luUploadEntry | 1.3.6.1.4.1.677.5.1 | ||
| OBJECT-TYPE | |||
| LuUploadEntry | |||
| luUploadIPAddress | 1.3.6.1.4.1.677.5.1.1 | ||
| The IP address of the server to use for the upload when using TFTP-IP | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| luUploadIPGateway | 1.3.6.1.4.1.677.5.1.2 | ||
| The IP gateway to be used to access the server. If this variable is zero then use the default gateway in luOpIPGateway. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| luUploadIPXAddress | 1.3.6.1.4.1.677.5.1.3 | ||
| The IPX address of the server to use for the upload when using TFTP-IPX. The format of the address is = 12 bytes. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(12) | ||
| luUploadFileName | 1.3.6.1.4.1.677.5.1.4 | ||
| The filename under which to store the uploaded microcode. The maximum length of this string is device specific. If a string that is too long is written to this variable BAD VALUE will be returned. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| luUploadSource | 1.3.6.1.4.1.677.5.1.5 | ||
| The source for the upload. This will contain the luDeviceIndex for the upload source. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| luUploadState | 1.3.6.1.4.1.677.5.1.6 | ||
| The current state of the Upload | |||
| OBJECT-TYPE | |||
| INTEGER | idle(1), tftp-waiting-ip(2), tftp-running-ip(3), tftp-waiting-ipx(4), tftp-running-ipx(5) | ||
| luUploadFailureCode | 1.3.6.1.4.1.677.5.1.7 | ||
| While an upload is in progress this will always be 'no-error'. After an upload is complete this indicates the success or failure of the upload. If it is anything other than 'no-error' then 'luUploadStatusText' will contain a textual description of the error. Error codes from 100 upwards are errors returned from a TFTP server. Errors below this are locally generated. Configuration files may return errors after / before upload, as a result of reading a config file into the system. conf-file-gen-err - General (unknown error) conf-file-exec-error - Generation of config file resulted in execution errors. | |||
| OBJECT-TYPE | |||
| INTEGER | no-error(1), config-error(2), busy(3), timeout(4), cancelled(5), incompatible-file(6), file-too-big(7), protocol-error(8), flash-write-error(9), nvram-read-error(10), conf-file-gen-err(11), conf-file-exec-error(12), undefined-error(100), file-not-found(101), access-violation(102), out-of-memory(103), illegal-operation(104), unknown-transfer-id(105), file-already-exists(106), no-such-user(107) | ||
| luUploadStatusText | 1.3.6.1.4.1.677.5.1.8 | ||
| A display string describing the status of the upload in progress, or the reason for failure of the last upload. If FailureCode = no-error then StatusText may be empty. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| luUploadSize | 1.3.6.1.4.1.677.5.1.9 | ||
| While an upload is in progress this indicates the number of bytes transferred so far. After the upload is completed this remains at the final size uploaded. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| luUploadErrorLogName | 1.3.6.1.4.1.677.5.1.10 | ||
| The filename under which an error log has been created. In the case of file uploads that produce errors this file should contain a log of errors that occured | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| luUploadErrorLogLocation | 1.3.6.1.4.1.677.5.1.11 | ||
| The location of the error log. This will contain the luDeviceIndex for the error log | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| luDloadNotifications | 1.3.6.1.4.1.677.6 | ||
| OBJECT IDENTIFIER | |||
| luNotificationNextIndex | 1.3.6.1.4.1.677.6.1 | ||
| The Next available Index of the luNotificationDestTable | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| luNotificationDestTable | 1.3.6.1.4.1.677.6.2 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LuNotificationDestEntry | |||
| luNotificationDestEntry | 1.3.6.1.4.1.677.6.2.1 | ||
| OBJECT-TYPE | |||
| LuNotificationDestEntry | |||
| luNotificationIndex | 1.3.6.1.4.1.677.6.2.1.1 | ||
| The Index of this Destination entry. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| luNotificationIPAddress | 1.3.6.1.4.1.677.6.2.1.2 | ||
| The IP address of the trap receiver. If IPX Addresses are being used this entry must be zero. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| luNotificationIPGateway | 1.3.6.1.4.1.677.6.2.1.3 | ||
| The IP gateway of the trap receiver. If IPX Addresses are being used this entry must be zero. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| luNotificationIPXAddress | 1.3.6.1.4.1.677.6.2.1.4 | ||
| The IPX address of the trap receiver. If IP Addresses are being used this entry must be zero. The format of the address is = 12 bytes. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(12) | ||
| luNotificationNodeAddress | 1.3.6.1.4.1.677.6.2.1.5 | ||
| The Node address of the trap receiver. If IP Addresses are being used this entry must be zero. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| luNotificationTrapTypes | 1.3.6.1.4.1.677.6.2.1.6 | ||
| The Trap types this entry should receive. | |||
| OBJECT-TYPE | |||
| INTEGER | noDloadTraps(0), allDloadTraps(1) | ||
| luNotificationRowStatus | 1.3.6.1.4.1.677.6.2.1.7 | ||
| The Status of this entry in the table. Note the available states: active(1), -- Obviously Active. notInService(2) -- Configured but disabled. notReady(3), -- NOT fully configured. createAndGo(4), createAndWait(5) or destroy(6) | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| luDloadTrapCompleted | 1.3.6.1.4.1.677.6.3 | ||
| Indicates that a download has completed. | |||
| NOTIFICATION-TYPE | |||
| luOpIndex | |||
| luDownloadDestination | |||
| luDownloadFileName | |||
| luDownloadFailureCode | |||
| luUpLoadTrapCompleted | 1.3.6.1.4.1.677.6.4 | ||
| Indicates that a upload has completed. | |||
| NOTIFICATION-TYPE | |||
| luOpIndex | |||
| luUploadSource | |||
| luUploadFileName | |||
| luUploadFailureCode | |||
| LuOpEntry | |||
| SEQUENCE | |||
| OCTET STRING as luOpSerialNumber | |||
| OCTET STRING as luOpMCodeVersion | |||
| OCTET STRING as luOpBCodeVersion | |||
| DisplayString as luOpMCodeFilename | |||
| INTEGER as luOpAdminStatus | |||
| INTEGER as luOpOperStatus | |||
| INTEGER as luOpEraseFlashVersion | |||
| INTEGER as luOpDefaultFlashVersion | |||
| DisplayString as luOpConfFileName | |||
| INTEGER as luOpIndex | |||
| LuDeviceEntry | |||
| SEQUENCE | |||
| INTEGER as luDeviceIndex | |||
| DisplayString as luDeviceDescription | |||
| DisplayString as luDeviceLocation | |||
| OCTET STRING as luDeviceNumber | |||
| INTEGER as luDeviceType | |||
| DisplayString as luDeviceFileName | |||
| LuDownloadEntry | |||
| SEQUENCE | |||
| IpAddress as luDownloadIPAddress | |||
| IpAddress as luDownloadIPGateway | |||
| OCTET STRING as luDownloadIPXAddress | |||
| MacAddress as luDownloadNodeAddress | |||
| DisplayString as luDownloadFileName | |||
| INTEGER as luDownloadDestination | |||
| INTEGER as luDownloadState | |||
| INTEGER as luDownloadFailureCode | |||
| DisplayString as luDownloadStatusText | |||
| INTEGER as luDownloadSize | |||
| DisplayString as luDownloadErrorLogName | |||
| INTEGER as luDownloadErrorLogLocation | |||
| LuUploadEntry | |||
| SEQUENCE | |||
| IpAddress as luUploadIPAddress | |||
| IpAddress as luUploadIPGateway | |||
| OCTET STRING as luUploadIPXAddress | |||
| DisplayString as luUploadFileName | |||
| INTEGER as luUploadSource | |||
| INTEGER as luUploadState | |||
| INTEGER as luUploadFailureCode | |||
| DisplayString as luUploadStatusText | |||
| INTEGER as luUploadSize | |||
| DisplayString as luUploadErrorLogName | |||
| INTEGER as luUploadErrorLogLocation | |||
| LuNotificationDestEntry | |||
| SEQUENCE | |||
| INTEGER as luNotificationIndex | |||
| IpAddress as luNotificationIPAddress | |||
| IpAddress as luNotificationIPGateway | |||
| OCTET STRING as luNotificationIPXAddress | |||
| MacAddress as luNotificationNodeAddress | |||
| INTEGER as luNotificationTrapTypes | |||
| RowStatus as luNotificationRowStatus | |||