
| SNMPv2-TC | SNMPv2-SMI | RFC1213-MIB |
| RFC1155-SMI |
| TEXTUAL-CONVENTION | MODULE-IDENTITY | OBJECT-TYPE |
| NOTIFICATION-TYPE | ObjectName | Integer32 |
| Counter32 | Unsigned32 | DisplayString |
| enterprises |
| luminous | 1.3.6.1.4.1.4614 | ||
| OBJECT IDENTIFIER | |||
| lumADM | 1.3.6.1.4.1.4614.1 | ||
| OBJECT IDENTIFIER | |||
| lumTcMIB | 1.3.6.1.4.1.4614.1.9 | ||
| The Luminous TC MIB contains textual conventions for use in Luminous Networks MIBs. | |||
| MODULE-IDENTITY | |||
| LumShelfType | |||
| Type of chassis. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | mSeries(1), unused1(2), unused2(3), cSeries(4) | ||
| LumChassisPlane | |||
| Which plane in the chassis. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | front(1), back(2) | ||
| LumSlotNum | |||
| Number of a slot within a chassis plane. Note that 0 is not a valid slot and means unknown. | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | 0..32 | ||
| LumPortNum | |||
| Number of a port within a card.. Note that 0 is not a valid port and means unknown. | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | 0..32 | ||
| LumSimpleIndex | |||
| Simple abstract integer index for a table. | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | 1..65535 | ||
| LumPercent | |||
| A percentage value. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0..100 | ||
| LumRingDirection | |||
| Direction of a service of link from the ring point of view. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | none(1), west(2), east(3) | ||
| LumAdminStatus | |||
| Administrative Status of an entity. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | up(1), down(2) | ||
| LumOperStatus | |||
| Operational Status of an entity. This is based on IF-MIB ifOperStatus with the addition of misMatch. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | up(1), down(2), testing(3), unknown(4), dormant(5), notPresent(6), lowerLayerDown(7), misMatch(8) | ||
| LumControl | |||
| Control of an entity. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | unknown(1), disabled(2), enabled(3) | ||
| LumServiceMode | |||
| Service type for a port. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | none(1), wire(2), routing(3), policyForwarding(4) | ||
| LumPortType | |||
| What type of entity is this port. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | none(1), physical(2), subPortDemux(3) | ||
| LumPortCreateType | |||
| Was this port created explicitly or implicitly (e.g. chen channelizing a DS3, subports for DS1 are implicitly created. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | implicit(1), explicit(2) | ||
| LumPortDemuxType | |||
| What type of entity is this demux port. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | none(1), vlan(2), mplsTag(3), tdmChannel(4) | ||
| LumPortDemuxId | |||
| The substream identifier for this demux port. | |||
| TEXTUAL-CONVENTION | |||
| Unsigned32 | 0..65535 | ||
| LumConnectorType | |||
| Connector type for a physical port. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | none(1), rj45(2), scFiber(3), miniCoax(4), db9(5), sjFiber(6), stFiber(7) | ||
| LumSignalState | |||
| State of a hardware signal. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | idle(1), active(2) | ||
| LumName | |||
| Name of an entity. This should not include white space characters. | |||
| TEXTUAL-CONVENTION | |||
| DisplayString | SIZE(1..40) | ||
| LumDescr | |||
| Description of an entity. | |||
| TEXTUAL-CONVENTION | |||
| DisplayString | SIZE(1..80) | ||
| LumVersionString | |||
| Version of an entity. | |||
| TEXTUAL-CONVENTION | |||
| DisplayString | SIZE(1..20) | ||
| LumSerialNumString | |||
| Serial number of an entity. | |||
| TEXTUAL-CONVENTION | |||
| DisplayString | SIZE(1..21) | ||
| LumCleiString | |||
| CLEI code of an entity. | |||
| TEXTUAL-CONVENTION | |||
| DisplayString | SIZE(1..17) | ||
| LumManufactureString | |||
| Manufacture date of an entity. | |||
| TEXTUAL-CONVENTION | |||
| DisplayString | SIZE(1..20) | ||
| LumDateTimeString | |||
| Date and Time. | |||
| TEXTUAL-CONVENTION | |||
| DisplayString | SIZE(24) | ||
| LumCardBaseType | |||
| The base type of a card. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | none(1), sysCon(2), ring(3), t1(4), ether(5), alarm(6), upLink(7), ringIO(8), t1IO(9), etherIO(10), utility(11), oc12(12), oc12IO(13), gigE(14), gigEIO(15), oc12IOAlarm(16), etherFXIO(17), wdm(18), wdmIO(19), ringIOLR(21), ring2(22), ring2IO(23), ds3cc12(28), ds3cc12IO(29), ether24(32), ether24IO(33), asi(34), asiIOIn(35), asiIOOut(36), present(38) | ||
| LumCardType | |||
| The specific type of a card. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | none(1), sysCon(2), ring(3), t1(4), ether(5), alarm(6), upLink(7), ringIO(8), t1IO(9), etherIO(10), utility(11), oc12(12), oc12IO(13), gigE(14), gigEIO(15), oc12IOAlarm(16), etherFXIO(17), wdm(18), wdmIO(19), sysconR(20), ringIOLR(21), ring2(22), ring2IO(23), wdmBand1(24), wdmBand2(25), wdmBand3(26), wdmBand4(27), ds3cc12(28), ds3cc12IO(29), t3cc12(30), e3cc12(31), ether24(32), ether24IO(33), asi(34), asiIOIn(35), asiIOOut(36), gigERouting(37), present(38), sysconU(39), newCardType(40) | ||
| LumCardAdminState | |||
| The admininstrative state of a card. This indicates the state transition desired by the management. The actual success of transition is shown in the card operationla state. active(2) - request to set a card in an active but not backed up state. standby(3)- request to set a card to a standby state. outOfService(4) - request to set a card to OutOfService state, where it should respond to the management requests but not support any traffic activity. shutDown(5)-request to shut the card down completely. Deprecated. reset(6) -request to reset the card. switchover(7)- request to replace this card, currently in lumCardOperState of active(7) with the card currently in lumCardOperState of standby(3) which slot is referenced with lumStandbySlot. On success, lumCardOperState of this card should transition to outOfService(4). | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | none(1), active(2), standby(3), outOfService(4), shutDown(5), reset(6), switchover(7) | ||
| LumCardOperState | |||
| The operational state of a card. The Operational State indicates the current state of the card. It can be either the result of some administrative management action or internal card activity. none(1) - indicates that there is no card in the slot active (2) - means working fine, but not backed up standby(3) - means backing up other active(2) cards in case of a failure or management switchover requests outOfService(4) - a state where the card should respond to the management requests but not support any traffic activity. failure(5) - cannot function properly but still can respond to management requests. down(6) - card in the slot can't even respond to the management request. present(7) - card is present in the slot and not yet identified. initializing(8)-card is present in the slot and is initializing. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | none(1), active(2), standby(3), outOfService(4), failure(5), down(6), present(7), initializing(8) | ||
| LumCardFailureState | |||
| The failure state of a card. This is usually none(1), unless card operational state is equal to failure(5). Even if card operational state is equal to failure(5), still, this can be none(1), simply indicating that no information about this failure state is available. Otherwise criticalFault(2) indicates that the card cannot perform one of it's required functions properly. The management action is recommended (can be even reset or, if mulfunctioning, be replace) to correct the problem. Otherwise the problem will persist. minorFault(3) indicates that a fault has occured but does not persist. The action from the management may not beneeded. minorAlarm(4) indicates that no action is needed. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | none(1), criticalFault(2), minorFault(3), minorAlarm(4) | ||
| LumOpticalWaveLength | |||
| The wavelength in nano-meters of an optical interface. | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | 1..65535 | ||
| LumOpticalFiberType | |||
| The fiber type used by an optical interface. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | unknown(1), singleMode(2), multiMode(3) | ||
| LumOpticalMaxLength | |||
| The maximum fiber length in meters of an optical interface. | |||
| TEXTUAL-CONVENTION | |||
| Integer32 | 1..1000000 | ||
| LumOpticalConnector | |||
| The connector type used by an optical interface. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | unknown(1), sc(2), lc(3) | ||
| LumOpticalServiceSupport | |||
| The service types supported by an optical interface. | |||
| TEXTUAL-CONVENTION | |||
| BITS | gigE1(0), gigE2(1), fiberChannel1(2), fiberChannel2(3), oc12(4), oc24(5), oc48(6), rpt(7), rptE2(8), oc3(9) | ||
| LumOpticalService | |||
| The service type active on an optical interface. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | none(1), gigE1(2), gigE2(3), fiberChannel1(4), fiberChannel2(5), oc12(6), oc24(7), oc48(8), rpt(9), rptE2(10), oc3(11) | ||
| LumTdmType | |||
| The TDM port or connection type. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | unknown(1), t1(2), e1(3), t3(4), e3(5) | ||
| LumImageState | |||
| The state of a program image in NVRAM. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | empty(1), trial(2), tried(3), accepted(4), unknown(5) | ||
| LumAlarmSeverity | |||
| The severity of an alarm of group of alarms. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | undefined(1), critical(2), major(3), minor(4), notAlarmed(5), notReported(6) | ||
| LumResetCmd | |||
| Reset command for an entity. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | none(1), reset(2) | ||