MCC16-MIB

File: MCC16-MIB.mib (559044 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
RFC-1215

Imported symbols

enterprises Gauge TimeTicks
IpAddress DisplayString PhysAddress
OBJECT-TYPE TRAP-TYPE

Defined Objects

transition 1.3.6.1.4.1.868
OBJECT IDENTIFIER    

productId 1.3.6.1.4.1.868.1
OBJECT IDENTIFIER    

chassisProdsId 1.3.6.1.4.1.868.1.4
OBJECT IDENTIFIER    

chassisSlotTypes 1.3.6.1.4.1.868.1.4.1
OBJECT IDENTIFIER    

chSlMc20p 1.3.6.1.4.1.868.1.4.1.1
OBJECT IDENTIFIER    

ceTbtFrl03Id 1.3.6.1.4.1.868.1.4.1.1.1
OBJECT IDENTIFIER    

ceCxTbt04Id 1.3.6.1.4.1.868.1.4.1.1.2
OBJECT IDENTIFIER    

ceCxFrl04Id 1.3.6.1.4.1.868.1.4.1.1.3
OBJECT IDENTIFIER    

cfSmMm02Id 1.3.6.1.4.1.868.1.4.1.1.4
OBJECT IDENTIFIER    

cfSmMm05Id 1.3.6.1.4.1.868.1.4.1.1.5
OBJECT IDENTIFIER    

caCf02Id 1.3.6.1.4.1.868.1.4.1.1.6
OBJECT IDENTIFIER    

cfSmMm06Id 1.3.6.1.4.1.868.1.4.1.1.7
OBJECT IDENTIFIER    

ct1e1Cf01Id 1.3.6.1.4.1.868.1.4.1.1.8
OBJECT IDENTIFIER    

ceRTxFx01Id 1.3.6.1.4.1.868.1.4.1.1.9
OBJECT IDENTIFIER    

ce100BtxFx04Id 1.3.6.1.4.1.868.1.4.1.1.10
OBJECT IDENTIFIER    

cpsCf01Id 1.3.6.1.4.1.868.1.4.1.1.12
OBJECT IDENTIFIER    

cbCf01Id 1.3.6.1.4.1.868.1.4.1.1.13
OBJECT IDENTIFIER    

carCf01Id 1.3.6.1.4.1.868.1.4.1.1.14
OBJECT IDENTIFIER    

carCf02Id 1.3.6.1.4.1.868.1.4.1.1.15
OBJECT IDENTIFIER    

cePswFx03Id 1.3.6.1.4.1.868.1.4.1.1.16
OBJECT IDENTIFIER    

cePswSx01Id 1.3.6.1.4.1.868.1.4.1.1.17
OBJECT IDENTIFIER    

cRs232Cf01Id 1.3.6.1.4.1.868.1.4.1.1.18
OBJECT IDENTIFIER    

cfSmMm04Id 1.3.6.1.4.1.868.1.4.1.1.24
OBJECT IDENTIFIER    

ce100BtxSx01Id 1.3.6.1.4.1.868.1.4.1.1.26
OBJECT IDENTIFIER    

ce100BtxFx04MtId 1.3.6.1.4.1.868.1.4.1.1.27
OBJECT IDENTIFIER    

cfdCd01Id 1.3.6.1.4.1.868.1.4.1.1.28
OBJECT IDENTIFIER    

ctrCf01Id 1.3.6.1.4.1.868.1.4.1.1.29
OBJECT IDENTIFIER    

ce100BtxFrl03Id 1.3.6.1.4.1.868.1.4.1.1.30
OBJECT IDENTIFIER    

mc20pEmptyId 1.3.6.1.4.1.868.1.4.1.1.31
OBJECT IDENTIFIER    

mc20pErrorId 1.3.6.1.4.1.868.1.4.1.1.32
OBJECT IDENTIFIER    

mc20pDblWideId 1.3.6.1.4.1.868.1.4.1.1.33
OBJECT IDENTIFIER    

chstrCf01Id 1.3.6.1.4.1.868.1.4.1.1.34
OBJECT IDENTIFIER    

ceTxSx02Id 1.3.6.1.4.1.868.1.4.1.1.35
OBJECT IDENTIFIER    

ceTbtFrl04Id 1.3.6.1.4.1.868.1.4.1.1.36
OBJECT IDENTIFIER    

chSlcps 1.3.6.1.4.1.868.1.4.1.2
OBJECT IDENTIFIER    

cpsmM100Id 1.3.6.1.4.1.868.1.4.1.2.1
OBJECT IDENTIFIER    

pSError 1.3.6.1.4.1.868.1.4.1.2.1.111
A monitored MIB variable has changed from its 'operational' state to its 'error' state.
TRAP-TYPE    

pSErrorClear 1.3.6.1.4.1.868.1.4.1.2.1.112
A monitored MIB variable has changed from its 'error' state to its 'operational' state.
TRAP-TYPE    

pSDeviceInserted 1.3.6.1.4.1.868.1.4.1.2.1.113
A new slide-in device (this includes some power supplies) was detected on the bus.
TRAP-TYPE    

pSDeviceRemoved 1.3.6.1.4.1.868.1.4.1.2.1.114
A slide-in device that had previously been detected on the bus has not been heard from in a long time, and is presumed to have been physically removed.
TRAP-TYPE    

pSDeviceColdStart 1.3.6.1.4.1.868.1.4.1.2.1.115
A slide-in device has indicated that it has rebooted. This is most common when the device is inserted into its slot, but in a few cases this trap indicates a warm start.
TRAP-TYPE    

pSPowerLost 1.3.6.1.4.1.868.1.4.1.2.1.116
The cabinet into which this management module is installed has lost power. Both the cabinet and the management module must support this feature for this trap to be sent.
TRAP-TYPE    

pSCabinetAdded 1.3.6.1.4.1.868.1.4.1.2.1.117
A new cabinet was detected on the bus.
TRAP-TYPE    

pSCabinetRemoved 1.3.6.1.4.1.868.1.4.1.2.1.118
A cabinet that had previously been detected on the bus has not been heard from in a long time, and is presumed to have been physically removed.
TRAP-TYPE    

cpsmM200Id 1.3.6.1.4.1.868.1.4.1.2.2
OBJECT IDENTIFIER    

cettf100Id 1.3.6.1.4.1.868.1.4.1.2.3
OBJECT IDENTIFIER    

cfetf100Id 1.3.6.1.4.1.868.1.4.1.2.4
OBJECT IDENTIFIER    

cfmff100Id 1.3.6.1.4.1.868.1.4.1.2.5
OBJECT IDENTIFIER    

cpsmp100Id 1.3.6.1.4.1.868.1.4.1.2.6
OBJECT IDENTIFIER    

csetf100Id 1.3.6.1.4.1.868.1.4.1.2.7
OBJECT IDENTIFIER    

cgetf100Id 1.3.6.1.4.1.868.1.4.1.2.8
OBJECT IDENTIFIER    

csdtf100Id 1.3.6.1.4.1.868.1.4.1.2.9
OBJECT IDENTIFIER    

cpsmp110Id 1.3.6.1.4.1.868.1.4.1.2.10
OBJECT IDENTIFIER    

cbftf100Id 1.3.6.1.4.1.868.1.4.1.2.11
OBJECT IDENTIFIER    

cetct100Id 1.3.6.1.4.1.868.1.4.1.2.12
OBJECT IDENTIFIER    

ccscf100Id 1.3.6.1.4.1.868.1.4.1.2.13
OBJECT IDENTIFIER    

cfetf105Id 1.3.6.1.4.1.868.1.4.1.2.14
OBJECT IDENTIFIER    

smacf100PId 1.3.6.1.4.1.868.1.4.1.2.15
OBJECT IDENTIFIER    

cpsld100Id 1.3.6.1.4.1.868.1.4.1.2.16
OBJECT IDENTIFIER    

cdftf100Id 1.3.6.1.4.1.868.1.4.1.2.17
OBJECT IDENTIFIER    

cpsvt100Id 1.3.6.1.4.1.868.1.4.1.2.18
OBJECT IDENTIFIER    

cemtf100Id 1.3.6.1.4.1.868.1.4.1.2.19
OBJECT IDENTIFIER    

captf100Id 1.3.6.1.4.1.868.1.4.1.2.20
OBJECT IDENTIFIER    

cfetf205Id 1.3.6.1.4.1.868.1.4.1.2.21
OBJECT IDENTIFIER    

cbftf150Id 1.3.6.1.4.1.868.1.4.1.2.22
OBJECT IDENTIFIER    

cgfeb100Id 1.3.6.1.4.1.868.1.4.1.2.23
OBJECT IDENTIFIER    

crmfe100Id 1.3.6.1.4.1.868.1.4.1.2.24
OBJECT IDENTIFIER    

crs2f100Id 1.3.6.1.4.1.868.1.4.1.2.25
OBJECT IDENTIFIER    

crs4f100Id 1.3.6.1.4.1.868.1.4.1.2.26
OBJECT IDENTIFIER    

cmefg100Id 1.3.6.1.4.1.868.1.4.1.2.27
OBJECT IDENTIFIER    

cpsEmptyId 1.3.6.1.4.1.868.1.4.1.2.1001
OBJECT IDENTIFIER    

cpsDblWideId 1.3.6.1.4.1.868.1.4.1.2.1002
OBJECT IDENTIFIER    

cpsUnknownDeviceId 1.3.6.1.4.1.868.1.4.1.2.1003
OBJECT IDENTIFIER    

chassisMcc16Id 1.3.6.1.4.1.868.1.4.2
OBJECT IDENTIFIER    

mcc16Error 1.3.6.1.4.1.868.1.4.2.101
A monitored MIB variable has changed from its 'operational' state to 'not present' or its 'error' state.
TRAP-TYPE    

mcc16ErrorClear 1.3.6.1.4.1.868.1.4.2.102
A monitored MIB variable has changed from a 'not present' or 'error' state to its 'operational' state.
TRAP-TYPE    

mcc16PSState 1.3.6.1.4.1.868.1.4.2.103
The power indication on a power supply has changed, or a power supply was non-operational at the time of a warm start.
TRAP-TYPE    

chassisCpsmc1800Id 1.3.6.1.4.1.868.1.4.3
OBJECT IDENTIFIER    

chassisCpsmc1850Id 1.3.6.1.4.1.868.1.4.4
OBJECT IDENTIFIER    

chassisCpsmc0800Id 1.3.6.1.4.1.868.1.4.5
OBJECT IDENTIFIER    

chassisCpsmc1300Id 1.3.6.1.4.1.868.1.4.6
OBJECT IDENTIFIER    

chassisCpsmc0200Id 1.3.6.1.4.1.868.1.4.7
OBJECT IDENTIFIER    

chassisSmacf100LCId 1.3.6.1.4.1.868.1.4.8
OBJECT IDENTIFIER    

chassisCpsmc1900Id 1.3.6.1.4.1.868.1.4.9
OBJECT IDENTIFIER    

chassisSmacf100Id 1.3.6.1.4.1.868.1.4.10
OBJECT IDENTIFIER    

products 1.3.6.1.4.1.868.2
OBJECT IDENTIFIER    

chassis 1.3.6.1.4.1.868.2.4
OBJECT IDENTIFIER    

card 1.3.6.1.4.1.868.2.4.1
OBJECT IDENTIFIER    

slotMc20p 1.3.6.1.4.1.868.2.4.1.1
OBJECT IDENTIFIER    

ceTbtFrl03Table 1.3.6.1.4.1.868.2.4.1.1.1
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/E-TBT-FRL-03 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CeTbtFrl03Entry

ceTbtFrl03Entry 1.3.6.1.4.1.868.2.4.1.1.1.1
State of LEDs on a single C/E-TBT-FRL-03
OBJECT-TYPE    
  CeTbtFrl03Entry  

ceTbtFrl03Index 1.3.6.1.4.1.868.2.4.1.1.1.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

ceTbtFrl03FiberRecv 1.3.6.1.4.1.868.2.4.1.1.1.1.2
The state of the converter's Fiber Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  


ceTbtFrl03TPRecv 1.3.6.1.4.1.868.2.4.1.1.1.1.4
The state of the converter's Twisted Pair Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  


ceTbtFrl03Power 1.3.6.1.4.1.868.2.4.1.1.1.1.6
The state of the converter's Power LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ceCxTbt04Table 1.3.6.1.4.1.868.2.4.1.1.2
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/E-CX-TBT-04 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CeCxTbt04Entry

ceCxTbt04Entry 1.3.6.1.4.1.868.2.4.1.1.2.1
State of LEDs on a single C/E-CX-TBT-04
OBJECT-TYPE    
  CeCxTbt04Entry  

ceCxTbt04Index 1.3.6.1.4.1.868.2.4.1.1.2.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

ceCxTbt04Jabber 1.3.6.1.4.1.868.2.4.1.1.2.1.2
The state of the converter's Jabber LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ceCxTbt04CoaxRecv 1.3.6.1.4.1.868.2.4.1.1.2.1.3
The state of the converter's CoaxRecv LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ceCxTbt04TPRecv 1.3.6.1.4.1.868.2.4.1.1.2.1.4
The state of the converter's TPRecv LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  


ceCxTbt04Power 1.3.6.1.4.1.868.2.4.1.1.2.1.6
The state of the converter's Power LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ceCxFrl04Table 1.3.6.1.4.1.868.2.4.1.1.3
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/E-CX-FRL-04 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CeCxFrl04Entry

ceCxFrl04Entry 1.3.6.1.4.1.868.2.4.1.1.3.1
State of LEDs on a single C/E-CX-FRL-04
OBJECT-TYPE    
  CeCxFrl04Entry  

ceCxFrl04Index 1.3.6.1.4.1.868.2.4.1.1.3.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

ceCxFrl04Jabber 1.3.6.1.4.1.868.2.4.1.1.3.1.2
The state of the converter's Jabber LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ceCxFrl04CoaxRecv 1.3.6.1.4.1.868.2.4.1.1.3.1.3
The state of the converter's CoaxRecv LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ceCxFrl04FLRecv 1.3.6.1.4.1.868.2.4.1.1.3.1.4
The state of the converter's FLRecv LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  


ceCxFrl04Power 1.3.6.1.4.1.868.2.4.1.1.3.1.6
The state of the converter's Power LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfSmMm02Table 1.3.6.1.4.1.868.2.4.1.1.4
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/F-SM-MM-02 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CfSmMm02Entry

cfSmMm02Entry 1.3.6.1.4.1.868.2.4.1.1.4.1
State of LEDs on a single C/F-SM-MM-02
OBJECT-TYPE    
  CfSmMm02Entry  

cfSmMm02Index 1.3.6.1.4.1.868.2.4.1.1.4.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

cfSmMm02MMSignalDetect 1.3.6.1.4.1.868.2.4.1.1.4.1.2
The state of the converter's MMSignalDetect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfSmMm02SMSignalDetect 1.3.6.1.4.1.868.2.4.1.1.4.1.3
The state of the converter's SMSignalDetect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfSmMm02Power 1.3.6.1.4.1.868.2.4.1.1.4.1.4
The state of the converter's Power LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfSmMm05Table 1.3.6.1.4.1.868.2.4.1.1.5
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/F-SM-MM-05 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CfSmMm05Entry

cfSmMm05Entry 1.3.6.1.4.1.868.2.4.1.1.5.1
State of LEDs on a single C/F-SM-MM-05
OBJECT-TYPE    
  CfSmMm05Entry  

cfSmMm05Index 1.3.6.1.4.1.868.2.4.1.1.5.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

cfSmMm05SMSignalDetect 1.3.6.1.4.1.868.2.4.1.1.5.1.2
The state of the converter's SMSignalDetect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfSmMm05MMSignalDetect 1.3.6.1.4.1.868.2.4.1.1.5.1.3
The state of the converter's MMSignalDetect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfSmMm05Power 1.3.6.1.4.1.868.2.4.1.1.5.1.4
The state of the converter's Power LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

caCf02Table 1.3.6.1.4.1.868.2.4.1.1.6
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/A-CF-02 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CaCf02Entry

caCf02Entry 1.3.6.1.4.1.868.2.4.1.1.6.1
State of LEDs on a single C/A-CF-02
OBJECT-TYPE    
  CaCf02Entry  

caCf02Index 1.3.6.1.4.1.868.2.4.1.1.6.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

caCf02CopperSignalDetect 1.3.6.1.4.1.868.2.4.1.1.6.1.2
The state of the converter's CopperSignalDetect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

caCf02FiberSignalDetect 1.3.6.1.4.1.868.2.4.1.1.6.1.3
The state of the converter's FiberSignalDetect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

caCf02Power 1.3.6.1.4.1.868.2.4.1.1.6.1.4
The state of the converter's Power LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfSmMm06Table 1.3.6.1.4.1.868.2.4.1.1.7
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/F-SM-MM-06 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CfSmMm06Entry

cfSmMm06Entry 1.3.6.1.4.1.868.2.4.1.1.7.1
State of LEDs on a single C/F-SM-MM-06
OBJECT-TYPE    
  CfSmMm06Entry  

cfSmMm06Index 1.3.6.1.4.1.868.2.4.1.1.7.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

cfSmMm06MMSignalDetect 1.3.6.1.4.1.868.2.4.1.1.7.1.2
The state of the converter's MMSignalDetect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfSmMm06SMSignalDetect 1.3.6.1.4.1.868.2.4.1.1.7.1.3
The state of the converter's SMSignalDetect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfSmMm06Power 1.3.6.1.4.1.868.2.4.1.1.7.1.4
The state of the converter's Power LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ct1e1Cf01Table 1.3.6.1.4.1.868.2.4.1.1.8
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/T1E1-CF-01 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    Ct1e1Cf01Entry

ct1e1Cf01Entry 1.3.6.1.4.1.868.2.4.1.1.8.1
State of LEDs on a single C/T1E1-CF-01
OBJECT-TYPE    
  Ct1e1Cf01Entry  

ct1e1Cf01Index 1.3.6.1.4.1.868.2.4.1.1.8.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

ct1e1Cf01CopperSignalDetect 1.3.6.1.4.1.868.2.4.1.1.8.1.2
The state of the converter's CopperSignalDetect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ct1e1Cf01FiberSignalDetect 1.3.6.1.4.1.868.2.4.1.1.8.1.3
The state of the converter's FiberSignalDetect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ct1e1Cf01CoaxActive 1.3.6.1.4.1.868.2.4.1.1.8.1.4
The state of the converter's Coax Active LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ceRTxFx01Table 1.3.6.1.4.1.868.2.4.1.1.9
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/E-R-TX-FX-01 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CeRTxFx01Entry

ceRTxFx01Entry 1.3.6.1.4.1.868.2.4.1.1.9.1
State of LEDs on a single C/E-R-TX-FX-01
OBJECT-TYPE    
  CeRTxFx01Entry  

ceRTxFx01Index 1.3.6.1.4.1.868.2.4.1.1.9.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

ceRTxFx01TPPrimary 1.3.6.1.4.1.868.2.4.1.1.9.1.2
The state of the converter's Twisted Pair Primary LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ceRTxFx01FiberPrimary 1.3.6.1.4.1.868.2.4.1.1.9.1.3
The state of the converter's Fiber Primary LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ceRTxFx01TPSignalDetect 1.3.6.1.4.1.868.2.4.1.1.9.1.4
The state of the converter's Twisted Pair Signal Detect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ceRTxFx01FiberSignalDetect 1.3.6.1.4.1.868.2.4.1.1.9.1.5
The state of the converter's Fiber Signal Detect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxFx04Table 1.3.6.1.4.1.868.2.4.1.1.10
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/E-100-BTX-FX-04(ST/SC) media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    Ce100BtxFx04Entry

ce100BtxFx04Entry 1.3.6.1.4.1.868.2.4.1.1.10.1
State of LEDs on a single C/E-100-BTX-FX-04(ST/SC)
OBJECT-TYPE    
  Ce100BtxFx04Entry  

ce100BtxFx04Index 1.3.6.1.4.1.868.2.4.1.1.10.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

ce100BtxFx04TPRecv 1.3.6.1.4.1.868.2.4.1.1.10.1.2
The state of the converter's Twisted Pair Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxFx04FiberRecv 1.3.6.1.4.1.868.2.4.1.1.10.1.3
The state of the converter's Fiber Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxFx04TPSignalDetect 1.3.6.1.4.1.868.2.4.1.1.10.1.4
The state of the converter's Twisted Pair signal detect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxFx04FiberSignalDetect 1.3.6.1.4.1.868.2.4.1.1.10.1.5
The state of the converter's fiber signal detect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxFx04Power 1.3.6.1.4.1.868.2.4.1.1.10.1.6
The state of the converter's Power LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cpsCf01Table 1.3.6.1.4.1.868.2.4.1.1.12
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/PS-CF-01 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CpsCf01Entry

cpsCf01Entry 1.3.6.1.4.1.868.2.4.1.1.12.1
State of LEDs on a single C/PS-CF-01
OBJECT-TYPE    
  CpsCf01Entry  

cpsCf01Index 1.3.6.1.4.1.868.2.4.1.1.12.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

cpsCf01FiberRecv 1.3.6.1.4.1.868.2.4.1.1.12.1.2
The state of the converter's Fiber Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cpsCf01TPRecv 1.3.6.1.4.1.868.2.4.1.1.12.1.3
The state of the converter's Twisted Pair Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cpsCf01Power 1.3.6.1.4.1.868.2.4.1.1.12.1.4
The state of the converter's Power LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cbCf01Table 1.3.6.1.4.1.868.2.4.1.1.13
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/B-CF-01 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CbCf01Entry

cbCf01Entry 1.3.6.1.4.1.868.2.4.1.1.13.1
State of LEDs on a single C/B-CF-01
OBJECT-TYPE    
  CbCf01Entry  

cbCf01Index 1.3.6.1.4.1.868.2.4.1.1.13.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

cbCf01FiberRecv 1.3.6.1.4.1.868.2.4.1.1.13.1.2
The state of the converter's Fiber Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cbCf01TPCoaxRecv 1.3.6.1.4.1.868.2.4.1.1.13.1.3
The state of the converter's Twisted Pair/Coax Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cbCf01Power 1.3.6.1.4.1.868.2.4.1.1.13.1.4
The state of the converter's Power LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

carCf01Table 1.3.6.1.4.1.868.2.4.1.1.14
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/AR-CF-01 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CarCf01Entry

carCf01Entry 1.3.6.1.4.1.868.2.4.1.1.14.1
State of LEDs on a single C/AR-CF-01
OBJECT-TYPE    
  CarCf01Entry  

carCf01Index 1.3.6.1.4.1.868.2.4.1.1.14.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

carCf01FiberRecv 1.3.6.1.4.1.868.2.4.1.1.14.1.2
The state of the converter's Fiber Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

carCf01TPRecv 1.3.6.1.4.1.868.2.4.1.1.14.1.3
The state of the converter's Twisted Pair Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

carCf01Power 1.3.6.1.4.1.868.2.4.1.1.14.1.4
The state of the converter's Power LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

carCf02Table 1.3.6.1.4.1.868.2.4.1.1.15
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/AR-CF-02 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CarCf02Entry

carCf02Entry 1.3.6.1.4.1.868.2.4.1.1.15.1
State of LEDs on a single C/AR-CF-02
OBJECT-TYPE    
  CarCf02Entry  

carCf02Index 1.3.6.1.4.1.868.2.4.1.1.15.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

carCf02FiberRecv 1.3.6.1.4.1.868.2.4.1.1.15.1.2
The state of the converter's Fiber Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

carCf02CoaxRecv 1.3.6.1.4.1.868.2.4.1.1.15.1.3
The state of the converter's Coax Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

carCf02Power 1.3.6.1.4.1.868.2.4.1.1.15.1.4
The state of the converter's Power LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cePswFx03Table 1.3.6.1.4.1.868.2.4.1.1.16
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/E-PSW-FX-03 ethernet switch, then entry 'n' in this table exists and describes the state of the switch's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CePswFx03Entry

cePswFx03Entry 1.3.6.1.4.1.868.2.4.1.1.16.1
State of LEDs on a single C/E-PSW-FX-03
OBJECT-TYPE    
  CePswFx03Entry  

cePswFx03Index 1.3.6.1.4.1.868.2.4.1.1.16.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

cePswFx03TPFullDuplex 1.3.6.1.4.1.868.2.4.1.1.16.1.2
The state of the converter's Twisted Pair FDX LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cePswFx03FiberFullDuplex 1.3.6.1.4.1.868.2.4.1.1.16.1.3
The state of the converter's Fiber FDX LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  



cePswFx03TP100Mbps 1.3.6.1.4.1.868.2.4.1.1.16.1.6
The state of the converter's Twisted Pair 100Mbps LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cePswSx01Table 1.3.6.1.4.1.868.2.4.1.1.17
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/E-PSW-SX-01 ethernet switch, then entry 'n' in this table exists and describes the state of the switch's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CePswSx01Entry

cePswSx01Entry 1.3.6.1.4.1.868.2.4.1.1.17.1
State of LEDs on a single C/E-PSW-SX-01
OBJECT-TYPE    
  CePswSx01Entry  

cePswSx01Index 1.3.6.1.4.1.868.2.4.1.1.17.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

cePswSx01TPFullDuplex 1.3.6.1.4.1.868.2.4.1.1.17.1.2
The state of the converter's Twisted Pair FDX LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cePswSx01FiberFullDuplex 1.3.6.1.4.1.868.2.4.1.1.17.1.3
The state of the converter's Fiber FDX LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  



cePswSx01TP100Mbps 1.3.6.1.4.1.868.2.4.1.1.17.1.6
The state of the converter's Twisted Pair 100Mbps LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cRs232Cf01Table 1.3.6.1.4.1.868.2.4.1.1.18
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/RS232-CF-01 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CRs232Cf01Entry

cRs232Cf01Entry 1.3.6.1.4.1.868.2.4.1.1.18.1
State of LEDs on a single C/RS232-CF-01
OBJECT-TYPE    
  CRs232Cf01Entry  

cRs232Cf01Index 1.3.6.1.4.1.868.2.4.1.1.18.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

cRs232Cf01FiberLock 1.3.6.1.4.1.868.2.4.1.1.18.1.2
The state of the converter's Fiber Lock LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfSmMm04Table 1.3.6.1.4.1.868.2.4.1.1.24
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/F-SM-MM-04 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CfSmMm04Entry

cfSmMm04Entry 1.3.6.1.4.1.868.2.4.1.1.24.1
State of LEDs on a single C/F-SM-MM-04
OBJECT-TYPE    
  CfSmMm04Entry  

cfSmMm04Index 1.3.6.1.4.1.868.2.4.1.1.24.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

cfSmMm04MMSignalDetect 1.3.6.1.4.1.868.2.4.1.1.24.1.2
The state of the converter's Multi-Mode signal detect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfSmMm04SMSignalDetect 1.3.6.1.4.1.868.2.4.1.1.24.1.3
The state of the converter's Single-Mode signal detect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfSmMm04Power 1.3.6.1.4.1.868.2.4.1.1.24.1.4
The state of the converter's Power LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxSx01Table 1.3.6.1.4.1.868.2.4.1.1.26
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/E-100-BTX-SX-01 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    Ce100BtxSx01Entry

ce100BtxSx01Entry 1.3.6.1.4.1.868.2.4.1.1.26.1
State of LEDs on a single C/E-100-BTX-SX-01
OBJECT-TYPE    
  Ce100BtxSx01Entry  

ce100BtxSx01Index 1.3.6.1.4.1.868.2.4.1.1.26.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

ce100BtxSx01TPRecv 1.3.6.1.4.1.868.2.4.1.1.26.1.2
The state of the converter's Twisted Pair Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxSx01FiberRecv 1.3.6.1.4.1.868.2.4.1.1.26.1.3
The state of the converter's Fiber Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxSx01TPSignalDetect 1.3.6.1.4.1.868.2.4.1.1.26.1.4
The state of the converter's Twisted Pair signal detect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxSx01FiberSignalDetect 1.3.6.1.4.1.868.2.4.1.1.26.1.5
The state of the converter's fiber signal detect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxSx01Power 1.3.6.1.4.1.868.2.4.1.1.26.1.6
The state of the converter's Power LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxFx04MtTable 1.3.6.1.4.1.868.2.4.1.1.27
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/E-100-BTX-FX-04(MT) media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    Ce100BtxFx04MtEntry

ce100BtxFx04MtEntry 1.3.6.1.4.1.868.2.4.1.1.27.1
State of LEDs on a single C/E-100-BTX-FX-04(MT)
OBJECT-TYPE    
  Ce100BtxFx04MtEntry  

ce100BtxFx04MtIndex 1.3.6.1.4.1.868.2.4.1.1.27.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

ce100BtxFx04MtTPRecv 1.3.6.1.4.1.868.2.4.1.1.27.1.2
The state of the converter's Twisted Pair Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxFx04MtFiberRecv 1.3.6.1.4.1.868.2.4.1.1.27.1.3
The state of the converter's Fiber Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxFx04MtTPSignalDetect 1.3.6.1.4.1.868.2.4.1.1.27.1.4
The state of the converter's Twisted Pair signal detect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxFx04MtFiberSignalDetect 1.3.6.1.4.1.868.2.4.1.1.27.1.5
The state of the converter's fiber signal detect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxFx04MtPower 1.3.6.1.4.1.868.2.4.1.1.27.1.6
The state of the converter's Power LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfdCd01Table 1.3.6.1.4.1.868.2.4.1.1.28
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/FD-CD-01 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CfdCd01Entry

cfdCd01Entry 1.3.6.1.4.1.868.2.4.1.1.28.1
State of LEDs on a single C/FD-CD-01
OBJECT-TYPE    
  CfdCd01Entry  

cfdCd01Index 1.3.6.1.4.1.868.2.4.1.1.28.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

cfdCd01Lock 1.3.6.1.4.1.868.2.4.1.1.28.1.2
The state of the converter's Lock LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfdCd01TPRecv 1.3.6.1.4.1.868.2.4.1.1.28.1.3
The state of the converter's TPRecv LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfdCd01FiberRecv 1.3.6.1.4.1.868.2.4.1.1.28.1.4
The state of the converter's FiberRecv LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfdCd01TPSignalDetect 1.3.6.1.4.1.868.2.4.1.1.28.1.5
The state of the converter's TPSignalDetect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cfdCd01FiberSignalDetect 1.3.6.1.4.1.868.2.4.1.1.28.1.6
The state of the converter's FiberSignalDetect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ctrCf01Table 1.3.6.1.4.1.868.2.4.1.1.29
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/TR-CF-01 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CtrCf01Entry

ctrCf01Entry 1.3.6.1.4.1.868.2.4.1.1.29.1
State of LEDs on a single C/TR-CF-01
OBJECT-TYPE    
  CtrCf01Entry  

ctrCf01Index 1.3.6.1.4.1.868.2.4.1.1.29.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

ctrCf01FiberinOK 1.3.6.1.4.1.868.2.4.1.1.29.1.2
The state of the converter's FiberinOK LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ctrCf01TPinOK 1.3.6.1.4.1.868.2.4.1.1.29.1.3
The state of the converter's TPinOK LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ctrCf01Inserted 1.3.6.1.4.1.868.2.4.1.1.29.1.4
The state of the converter's Inserted LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxFrl03Table 1.3.6.1.4.1.868.2.4.1.1.30
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/E-100BTX-FRL-03 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    Ce100BtxFrl03Entry

ce100BtxFrl03Entry 1.3.6.1.4.1.868.2.4.1.1.30.1
State of LEDs on a single C/E-100BTX-FRL-03
OBJECT-TYPE    
  Ce100BtxFrl03Entry  

ce100BtxFrl03Index 1.3.6.1.4.1.868.2.4.1.1.30.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

ce100BtxFrl03Lock 1.3.6.1.4.1.868.2.4.1.1.30.1.2
The state of the converter's signal lock pin
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxFrl03TPRecv 1.3.6.1.4.1.868.2.4.1.1.30.1.3
The state of the converter's Twisted pair receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxFrl03FiberRecv 1.3.6.1.4.1.868.2.4.1.1.30.1.4
The state of the converter's Fiber Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxFrl03TPSignalDetect 1.3.6.1.4.1.868.2.4.1.1.30.1.5
The state of the converter's Twisted pair signal detect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ce100BtxFrl03FiberSignalDetect 1.3.6.1.4.1.868.2.4.1.1.30.1.6
The state of the converter's Fiber signal detect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

chstrCf01Table 1.3.6.1.4.1.868.2.4.1.1.34
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/HSTR-CF-01 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    ChstrCf01Entry

chstrCf01Entry 1.3.6.1.4.1.868.2.4.1.1.34.1
State of LEDs on a single C/HSTR-CF-01
OBJECT-TYPE    
  ChstrCf01Entry  

chstrCf01Index 1.3.6.1.4.1.868.2.4.1.1.34.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

chstrCf01TPRecv 1.3.6.1.4.1.868.2.4.1.1.34.1.2
The state of the converter's Twisted Pair Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

chstrCf01FiberRecv 1.3.6.1.4.1.868.2.4.1.1.34.1.3
The state of the converter's Fiber Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

chstrCf01TPSignalDetect 1.3.6.1.4.1.868.2.4.1.1.34.1.4
The state of the converter's Twisted Pair signal detect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

chstrCf01FiberSignalDetect 1.3.6.1.4.1.868.2.4.1.1.34.1.5
The state of the converter's fiber signal detect LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ceTxSx02Table 1.3.6.1.4.1.868.2.4.1.1.35
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/E-TX-SX-02 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CeTxSx02Entry

ceTxSx02Entry 1.3.6.1.4.1.868.2.4.1.1.35.1
State of LEDs on a single C/E-TX-SX-02
OBJECT-TYPE    
  CeTxSx02Entry  

ceTxSx02Index 1.3.6.1.4.1.868.2.4.1.1.35.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  



ceTxSx02100Mbps 1.3.6.1.4.1.868.2.4.1.1.35.1.4
The state of the converter's 100 Megabit Per Second LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ceTbtFrl04Table 1.3.6.1.4.1.868.2.4.1.1.36
One table entry per slot in the media converter chassis. If physical slot 'n' contains a working C/E-TBT-FRL-04 media converter, then entry 'n' in this table exists and describes the state of the converter's LEDs If slot 'n' is empty, does not exist, or contains a different type of device, then table entry 'n' does not exist.
OBJECT-TYPE    
  SEQUENCE OF  
    CeTbtFrl04Entry

ceTbtFrl04Entry 1.3.6.1.4.1.868.2.4.1.1.36.1
State of LEDs on a single C/E-TBT-FRL-04
OBJECT-TYPE    
  CeTbtFrl04Entry  

ceTbtFrl04Index 1.3.6.1.4.1.868.2.4.1.1.36.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER  

ceTbtFrl04FiberRecv 1.3.6.1.4.1.868.2.4.1.1.36.1.2
The state of the converter's Fiber Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  


ceTbtFrl04TPRecv 1.3.6.1.4.1.868.2.4.1.1.36.1.4
The state of the converter's Twisted Pair Receive LED
OBJECT-TYPE    
  INTEGER on(1), off(2)  


slotCps 1.3.6.1.4.1.868.2.4.1.2
OBJECT IDENTIFIER    

cpsSlotSummary 1.3.6.1.4.1.868.2.4.1.2.1
OBJECT IDENTIFIER    

cpsModuleTable 1.3.6.1.4.1.868.2.4.1.2.1.1
A table from which one can extract the model number of any device in the stack, given the serial number (BIA) of the cabinet and the slot number in which the device is installed.
OBJECT-TYPE    
  SEQUENCE OF  
    CpsModuleEntry

cpsModuleEntry 1.3.6.1.4.1.868.2.4.1.2.1.1.1
The model number entry for a single device.
OBJECT-TYPE    
  CpsModuleEntry  

cpsModuleBiaIndex 1.3.6.1.4.1.868.2.4.1.2.1.1.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

cpsModuleSlotIndex 1.3.6.1.4.1.868.2.4.1.2.1.1.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

cpsModuleModel 1.3.6.1.4.1.868.2.4.1.2.1.1.1.3
The model number of the device. See OIDs under chSlcps
OBJECT-TYPE    
  OBJECT IDENTIFIER  

cpsSlotDetail 1.3.6.1.4.1.868.2.4.1.2.2
OBJECT IDENTIFIER    

cpsmm100Table 1.3.6.1.4.1.868.2.4.1.2.2.1
Sparse table containing one entry for each CPSMM100-200 and other CPSMM100-xxx Point System Base Management Module in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Cpsmm100Entry

cpsmm100Entry 1.3.6.1.4.1.868.2.4.1.2.2.1.1
Status and configuration entries for a single CPSMM100
OBJECT-TYPE    
  Cpsmm100Entry  

cpsmm100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.1.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

cpsmm100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.1.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

cpsmm100Groups 1.3.6.1.4.1.868.2.4.1.2.2.1.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CPSMM100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

cpsmm100Reset 1.3.6.1.4.1.868.2.4.1.2.2.1.1.4
Set this to reset(1) to cause the CPSMM100 to reboot.
OBJECT-TYPE    
  INTEGER reset(1), noReset(2)  

cpsmm100SaveConfig 1.3.6.1.4.1.868.2.4.1.2.2.1.1.5
Set this to saveConfig(1) to force configuration changes made since the last saveConfig to be copied from RAM to flash memory. If changes are made to the configuration of a CPSMM100 and SaveConfig is not subsequently set to 1, the changes will be made only in RAM and the device will revert to its previous configuration at the next reboot. After the save completes, SaveConfig automatically reverts to noSaveConfig(2).
OBJECT-TYPE    
  INTEGER saveConfig(1), noSaveConfig(2)  

cpsmm100HwRevision 1.3.6.1.4.1.868.2.4.1.2.2.1.1.6
The hardware revision of this device
OBJECT-TYPE    
  DisplayString  

cpsmm100SwRevision 1.3.6.1.4.1.868.2.4.1.2.2.1.1.7
The revision of the agent firmware for this device.
OBJECT-TYPE    
  DisplayString  

cpsmm100IPAddress 1.3.6.1.4.1.868.2.4.1.2.2.1.1.8
The IP Address of the Ethernet interface of this device
OBJECT-TYPE    
  IpAddress  

cpsmm100SubnetMask 1.3.6.1.4.1.868.2.4.1.2.2.1.1.9
The subnet mask used by the Ethernet interface of this device
OBJECT-TYPE    
  IpAddress  

cpsmm100Gateway 1.3.6.1.4.1.868.2.4.1.2.2.1.1.10
The IP gateway used by the Ethernet interface of this device
OBJECT-TYPE    
  IpAddress  

cpsmm100IsPrimary 1.3.6.1.4.1.868.2.4.1.2.2.1.1.11
In a given Point System stack, multiple base management modules can be installed, but only one can be the Primary. The Primary is responsible for scanning the stack for modules, collecting status information and distributing new configuration settings. The Primary management module is therefore the only one that can accept an SNMP SET PDU. Compare this variable with cpsIsPrimary.0
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsmm100WantPrimary 1.3.6.1.4.1.868.2.4.1.2.2.1.1.12
Normally, the Management Module installed in the cabinet with the lowest serial number (BIA) in the lowest (leftmost) slot that has fully established network connectivity will be selected as the Primary. Setting WantPrimary to yes(1) causes this device to be preferred over all devices with a WantPrimary value of no(2) during these Primary/Standby negotiations. If more than one device is configured with the value yes(1), these modules negotiate amongst themselves using the default rule above. Setting WantPrimary to always(3) causes the module to ignore the results of the negotiations and immediately and persistently assert primary status. Use of always(3) is not recommended except on advice of Transition Networks technical support, since it may cause your system to behave unpredictably. Setting more than one module in a stack to always(3) will cause erratic behavior.
OBJECT-TYPE    
  INTEGER yes(1), no(2), always(3)  

cpsmm100CanPrimary 1.3.6.1.4.1.868.2.4.1.2.2.1.1.13
Value is yes(1) if this device is eligible to become the Primary Management Module. Currently, lack of IP/Ethernet connectivity is the only reason that a module can be ineligible.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  


cpsmm100TntRIP 1.3.6.1.4.1.868.2.4.1.2.2.1.1.15
This feature in obsolete as of 08/17/2001. Telnet 'trusted' IP address. Telnet access to the CPSMM100 can be limited to a single station by placing its IP address in TntRIP. Any incoming Telnet request from a station whose IP address does not match TntRIP is ignored. The TntRIP can be modified to accept an entire subnet or other group of IP stations by using TntRIPMask, defined below.
OBJECT-TYPE    
  IpAddress  

cpsmm100TntRIPMask 1.3.6.1.4.1.868.2.4.1.2.2.1.1.16
This feature in obsolete as of 08/17/2001. Telnet 'trusted' address mask. See cpsmm100TntRIP. This value can be used to exclude bit positions from consideration when applying TntRIP (above) to a Telnet connection request. For each bit position in TntRIPMask that is a 1, the corresponding bits in the TntRIP and the IP address of the connecting client must be the same. If this is not true, the connection attempt is ignored. Note that the TntRIPMask differs from a true subnet mask (which must have all '1' bits at the left and all '0' bits at the right) in that it may use any bit pattern.
OBJECT-TYPE    
  IpAddress  

cpsmm100SNMPTrapMgr 1.3.6.1.4.1.868.2.4.1.2.2.1.1.17
Traps generated by this management module will be sent to this IP address.
OBJECT-TYPE    
  IpAddress  

cpsmm100SNMPTrapInterval 1.3.6.1.4.1.868.2.4.1.2.2.1.1.18
For future expansion, not currently implemented.
OBJECT-TYPE    
  INTEGER  

cpsmm100SysUpTime 1.3.6.1.4.1.868.2.4.1.2.2.1.1.19
Mirror of this Management Module's system.sysUpTime.0
OBJECT-TYPE    
  TimeTicks  

cpsmm100SysContact 1.3.6.1.4.1.868.2.4.1.2.2.1.1.20
Mirror of this Management Module's system.sysContact.0
OBJECT-TYPE    
  DisplayString  

cpsmm100SysName 1.3.6.1.4.1.868.2.4.1.2.2.1.1.21
Mirror of this Management Module's system.sysName.0
OBJECT-TYPE    
  DisplayString  

cpsmm100SysLocation 1.3.6.1.4.1.868.2.4.1.2.2.1.1.22
Mirror of this Management Module's system.sysLocation.0
OBJECT-TYPE    
  DisplayString  

cpsmm100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.1.1.23
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cpsmm100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.1.1.24
The serial number of this device.
OBJECT-TYPE    
  INTEGER  

cpsmm100ICIF 1.3.6.1.4.1.868.2.4.1.2.2.1.1.25
Multiple Management Modules can be installed in a Point System stack. For each cabinet in the stack, exactly one module must be selected to communicate configuration changes to the cabinet hardware and provide a communications pathway to other cabinets. This module is known as the Inter-Cabinet Communications Interface. If there are any Base Management Modules in the cabinet, the one in the lowest slot will be the ICIF. Otherwise, it will be the Expansion Management Module in the lowest slot.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsmm100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.1.1.26
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cpsmm100LastGasp 1.3.6.1.4.1.868.2.4.1.2.2.1.1.27
Last Gasp support for this device.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsmm100SNMPTrapMgr2 1.3.6.1.4.1.868.2.4.1.2.2.1.1.28
Traps generated by this management module will be sent to this IP address.
OBJECT-TYPE    
  IpAddress  

cpsmm100SNMPTrapMgr3 1.3.6.1.4.1.868.2.4.1.2.2.1.1.29
Traps generated by this management module will be sent to this IP address.
OBJECT-TYPE    
  IpAddress  

cpsmm100SNMPTrapMgr4 1.3.6.1.4.1.868.2.4.1.2.2.1.1.30
Traps generated by this management module will be sent to this IP address.
OBJECT-TYPE    
  IpAddress  

cpsmm100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.1.1.31
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cpsmm200Table 1.3.6.1.4.1.868.2.4.1.2.2.2
Sparse table containing one entry for each CPSMM200-210 and other CPSMM200-xxx Point System Expansion Management Module in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Cpsmm200Entry

cpsmm200Entry 1.3.6.1.4.1.868.2.4.1.2.2.2.1
Status entries for a single cpsmm200. (The CPSMM200 has no configuration)
OBJECT-TYPE    
  Cpsmm200Entry  

cpsmm200BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.2.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

cpsmm200SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.2.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

cpsmm200SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.2.1.3
The serial number of this device
OBJECT-TYPE    
  INTEGER  

cpsmm200ICIF 1.3.6.1.4.1.868.2.4.1.2.2.2.1.4
Multiple Management Modules can be installed in a Point System stack. For each cabinet in the stack, exactly one module must be selected to communicate configuration changes to the cabinet hardware and provide a communications pathway to other cabinets. This module is known as the Inter-Cabinet Communications Interface. If there are any Base Management Modules in the cabinet, the one in the lowest slot will be the ICIF. Otherwise, it will be the Expansion Management Module in the lowest slot.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsmm200MRevision 1.3.6.1.4.1.868.2.4.1.2.2.2.1.5
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cettf100Table 1.3.6.1.4.1.868.2.4.1.2.2.3
Sparse table containing one entry for each CETTF100 10Mbps Twisted-Pair to Fiber Ethernet Media Converter in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Cettf100Entry

cettf100Entry 1.3.6.1.4.1.868.2.4.1.2.2.3.1
Status and configuration entries for a single CETTF100
OBJECT-TYPE    
  Cettf100Entry  

cettf100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.3.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

cettf100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.3.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

cettf100Groups 1.3.6.1.4.1.868.2.4.1.2.2.3.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CETTF100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

cettf100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.3.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cettf100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.3.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cettf100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.3.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  

cettf100ConnA 1.3.6.1.4.1.868.2.4.1.2.2.3.1.7
The style of Fiber connector built into this device
OBJECT-TYPE    
  CpsConnector  

cettf100ConnB 1.3.6.1.4.1.868.2.4.1.2.2.3.1.8
The style of Copper connector built into this device
OBJECT-TYPE    
  CpsConnector  



cettf100Fault 1.3.6.1.4.1.868.2.4.1.2.2.3.1.11
Value is yes(1) when either TPLink or FiberLink has value linkDown(2)
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cettf100TPActivity 1.3.6.1.4.1.868.2.4.1.2.2.3.1.12
Network traffic indicator for Copper side of this device
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cettf100FiberActivity 1.3.6.1.4.1.868.2.4.1.2.2.3.1.13
Network traffic indicator for Fiber side of this device
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cettf100AutoCross 1.3.6.1.4.1.868.2.4.1.2.2.3.1.14
Enable/Disable for automatic copper TX/RX pair correction
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cettf100LinkPassThrough 1.3.6.1.4.1.868.2.4.1.2.2.3.1.15
Enable/Disable for Link Pass Through, a feature that causes loss of link on one side of a media converter to be passed through to the other side, so that upstream equipment can see the fault condition.
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cettf100ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.3.1.16
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

cettf100Enabled 1.3.6.1.4.1.868.2.4.1.2.2.3.1.17
When this configuration item is set to no(2), the device passes no network traffic.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cettf100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.3.1.18
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cfetf100Table 1.3.6.1.4.1.868.2.4.1.2.2.4
Sparse table containing one entry for each CFTEF100 100Mbps Twisted-Pair to Fiber Ethernet Media Converter in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Cfetf100Entry

cfetf100Entry 1.3.6.1.4.1.868.2.4.1.2.2.4.1
Status and configuration entries for a single CFETF100
OBJECT-TYPE    
  Cfetf100Entry  

cfetf100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.4.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

cfetf100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.4.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

cfetf100Groups 1.3.6.1.4.1.868.2.4.1.2.2.4.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CFETF100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

cfetf100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.4.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cfetf100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.4.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cfetf100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.4.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  

cfetf100ConnA 1.3.6.1.4.1.868.2.4.1.2.2.4.1.7
The style of Fiber connector built into this device
OBJECT-TYPE    
  CpsConnector  

cfetf100ConnB 1.3.6.1.4.1.868.2.4.1.2.2.4.1.8
The style of Copper connector built into this device
OBJECT-TYPE    
  CpsConnector  



cfetf100Fault 1.3.6.1.4.1.868.2.4.1.2.2.4.1.11
Value is yes(1) when either TPLink or FiberLink has value linkDown(2)
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cfetf100FastLinkPulse 1.3.6.1.4.1.868.2.4.1.2.2.4.1.12
When set to autonegotiate(1), converter sends Fast Link Pulses on its twisted pair port, thereby participating in autonegotiation of duplex between the converter's twisted pair port and that of the connected station. If that station supports Full- Duplex (FDX) operation, FDX will be used. If not, the twisted pair will operate in Half-Duplex (HDX) mode. When set to hdx100Btx(2), the converter instead sends 100Mbps idles (rather than Fast Link Pulses) on its twisted pair port (i.e. it declines to negotiate), which forces the twisted pair to operate in HDX mode regardless of the capabilities of the connected station. When operating in HDX mode, the twisted pair can support traffic in only one direction at a time. In FDX mode, traffic can pass in both directions simultaneously, thus theoretically doubling network performance.
OBJECT-TYPE    
  INTEGER autonegotiate(1), hdx100Btx(2)  

cfetf100Enabled 1.3.6.1.4.1.868.2.4.1.2.2.4.1.13
When this configuration item is set to no(2), the device passes no network traffic.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cfetf100Pause 1.3.6.1.4.1.868.2.4.1.2.2.4.1.14
The Pause feature allows Ethernet MACs that support it to send data pacing 'Pause' messages to each other. Support for Pause is negotiated at the physical level and passed up to the MAC. While the MAC's Pause messages themselves can pass over the fiber link that this pair of media converters introduces, the TP physical layer negotiations to enable Pause can not. Therefore, if both end station MACs support Pause and wish to use it, the Pause negotiation must be re-generated by the media converters on both ends. By setting this configuration option to enabled(1), you are indicating to the local twisted pair station that the twisted pair station on the other side of the other media converter supports Pause and wishes to use it. This variable must be set consistently on both of the paired media converters.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cfetf100LinkPassThrough 1.3.6.1.4.1.868.2.4.1.2.2.4.1.15
Enable/Disable for Link Pass Through, a feature that causes loss of link on one side of a media converter to be passed through to the other side, so that upstream equipment can see the fault condition.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cfetf100AutoCross 1.3.6.1.4.1.868.2.4.1.2.2.4.1.16
Enable/Disable for automatic copper TX/RX pair correction. When disabled, the port operates in MDI mode.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cfetf100TPActivity 1.3.6.1.4.1.868.2.4.1.2.2.4.1.17
Network traffic indicator for Copper side of this device
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

cfetf100FiberActivity 1.3.6.1.4.1.868.2.4.1.2.2.4.1.18
Network traffic indicator for Fiber side of this device
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

cfetf100ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.4.1.19
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

cfetf100FarEndFault 1.3.6.1.4.1.868.2.4.1.2.2.4.1.20
Far End Fault configuration of this device. This setting can only be changed by the physical jumper setting on the slide in card, for some devices, if it is available. Far End Fault is software read-write on other devices. Far End Fault causes the fiber transmitter to generate a Far End Fault pattern upon the loss of a receiver signal detect. When the receiver detects signal again, the transmitter stops transmitting the Far End Fault pattern.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

cfetf100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.4.1.21
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cfmff100Table 1.3.6.1.4.1.868.2.4.1.2.2.5
Sparse table containing one entry for each CFMFF100 SingleMode to MultiMode Fiber Media Converter in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Cfmff100Entry

cfmff100Entry 1.3.6.1.4.1.868.2.4.1.2.2.5.1
Status and configuration entries for a single CFMFF100
OBJECT-TYPE    
  Cfmff100Entry  

cfmff100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.5.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

cfmff100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.5.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

cfmff100Groups 1.3.6.1.4.1.868.2.4.1.2.2.5.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CFMFF100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

cfmff100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.5.1.4
The marketing revision of the device
OBJECT-TYPE    
  INTEGER  

cfmff100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.5.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cfmff100ConnA 1.3.6.1.4.1.868.2.4.1.2.2.5.1.6
The style of SingleMode connector built into this device
OBJECT-TYPE    
  CpsConnector  

cfmff100ConnB 1.3.6.1.4.1.868.2.4.1.2.2.5.1.7
The style of MultiMode connector built into this device
OBJECT-TYPE    
  CpsConnector  

cfmff100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.5.1.8
The serial number of this device
OBJECT-TYPE    
  INTEGER  

cfmff100SMSignal 1.3.6.1.4.1.868.2.4.1.2.2.5.1.9
Status of singlemode signal detect for this device
OBJECT-TYPE    
  INTEGER signalUp(1), signalDown(2)  

cfmff100MMSignal 1.3.6.1.4.1.868.2.4.1.2.2.5.1.10
Status of singlemode signal detect for this device
OBJECT-TYPE    
  INTEGER signalUp(1), signalDown(2)  

cfmff100Enabled 1.3.6.1.4.1.868.2.4.1.2.2.5.1.11
Ports on this device can be disabled individually. When this control is set to yes(1), the entire device is enabled. When it is set to noP1(2), the SingleMode port is disabled. noP2(3) disables the MultiMode port only, and no(4) disables both. For most purposes, the values noP1(2), noP2(3), and no(4) are equivalent.
OBJECT-TYPE    
  INTEGER yes(1), noP1(2), noP2(3), no(4)  

cfmff100PortShutOff 1.3.6.1.4.1.868.2.4.1.2.2.5.1.12
This variable reflects the status of the DPT/OPP jumper on the board. This jumper controls the behavior of the converter when a loss of signal is detected. When the jumper is in the default OPP position, the loss of signal detect on one port causes the opposite port to be shut down. In this case, Port Shutoff is said to be disabled(2). In the DPT (enabled(1)) position, both ports are shut down. Use of the DPT position is discouraged, as it is more likely to lead to a signal loss condition from which the converter is unable to recover.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cfmff100ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.5.1.13
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

cfmff100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.5.1.14
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cpsmp100Table 1.3.6.1.4.1.868.2.4.1.2.2.6
Sparse table containing one entry for each CPSMP100 IFO (Instant Fail-Over) Power Supply in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Cpsmp100Entry

cpsmp100Entry 1.3.6.1.4.1.868.2.4.1.2.2.6.1
Status and configuration entries for a single CPSMP100
OBJECT-TYPE    
  Cpsmp100Entry  

cpsmp100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.6.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

cpsmp100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.6.1.2
The slot in which the device is installed. Power Supplies occupy special slots numbered 125 and higher.
OBJECT-TYPE    
  INTEGER  

cpsmp100Groups 1.3.6.1.4.1.868.2.4.1.2.2.6.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CPSMP100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

cpsmp100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.6.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cpsmp100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.6.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cpsmp100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.6.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  

cpsmp100Mode 1.3.6.1.4.1.868.2.4.1.2.2.6.1.7
When one power supply is set to master(1) and the other is set to slave(2), the master will supply all power to the cabinet, and the slave will take over if the master stops supplying power. This is useful when (for example) one supply is attached to a wall socket and the other to a battery backup. The cabinet can be directed to only draw power from batteries when there is no alternative. When both power supplies are set to master(1), the results are determined automatically. WARNING: It is up to the system administrator to ensure that at least one power supply is set to master(1). It is illegal to set all power supplies to slave(2). If this occurs, the cabinet may lose all power under certain circumstances, even if power is available.
OBJECT-TYPE    
  INTEGER master(1), slave(2)  

cpsmp100ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.6.1.8
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

cpsmp100RemoteFan 1.3.6.1.4.1.868.2.4.1.2.2.6.1.9
A Remote Fan is a device that fits in a power supply slot but contains no power supply, only a fan. These devices are not manageable, but if present they will be reported by the manageable supply that accompanies it.
OBJECT-TYPE    
  INTEGER installed(1), notInstalled(2)  

cpsmp100PowerOK 1.3.6.1.4.1.868.2.4.1.2.2.6.1.10
This variable has the value yes(1) any time this supply is capable of supplying at least 11.6 volts to the cabinet. Note that a value of no(2) does not necessarily indicate hard failure. A power supply can be detected even if it is powered down or not plugged in as long as another power supply has PowerOK=yes(1) and InUse=yes(1). In this case, PowerOK will be no(2) for the disabled power supply.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsmp100InUse 1.3.6.1.4.1.868.2.4.1.2.2.6.1.11
Value is yes(1) when this supply is currently selected to supply power to the cabinet.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsmp100ChassisPower 1.3.6.1.4.1.868.2.4.1.2.2.6.1.12
Power currently supplied to the cabinet, in milliwatts
OBJECT-TYPE    
  INTEGER  

cpsmp100ChassisTemp 1.3.6.1.4.1.868.2.4.1.2.2.6.1.13
The temperature inside the cabinet as detected by the power supply, in tenths of degrees centigrade
OBJECT-TYPE    
  INTEGER  

cpsmp100RFanFault 1.3.6.1.4.1.868.2.4.1.2.2.6.1.14
Normally no(2), this value changes to yes(1) when an installed Remote fan is drawing excessive current or none at all.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsmp100LFanFault 1.3.6.1.4.1.868.2.4.1.2.2.6.1.15
Normally no(2), this value changes to yes(1) when the Local fan is drawing excessive current or none at all.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsmp100SupplyType 1.3.6.1.4.1.868.2.4.1.2.2.6.1.16
The supply voltage that this unit is designed to accept. If AC(1), the supply accepts 90-260VAC, 47 to 400Hz. If DC48(2), the supply accepts 38-75VDC.
OBJECT-TYPE    
  INTEGER ac(1), dc48(2)  

cpsmp100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.6.1.17
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

csetf100Table 1.3.6.1.4.1.868.2.4.1.2.2.7
Sparse table containing one entry for each CSETF100 10/100Mbps Twisted-Pair to Fiber Ethernet Media Converter in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Csetf100Entry

csetf100Entry 1.3.6.1.4.1.868.2.4.1.2.2.7.1
One table entry per piece of management module information. Entry 'n' does not exist.
OBJECT-TYPE    
  Csetf100Entry  

csetf100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.7.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

csetf100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.7.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

csetf100Groups 1.3.6.1.4.1.868.2.4.1.2.2.7.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CSETF100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

csetf100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.7.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

csetf100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.7.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), inactive(3)  

csetf100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.7.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  

csetf100ConnA 1.3.6.1.4.1.868.2.4.1.2.2.7.1.7
The style of Fiber connector built into this device
OBJECT-TYPE    
  CpsConnector  

csetf100ConnB 1.3.6.1.4.1.868.2.4.1.2.2.7.1.8
The style of Copper connector built into this device
OBJECT-TYPE    
  CpsConnector  



csetf100AutoCross 1.3.6.1.4.1.868.2.4.1.2.2.7.1.11
Enable/Disable for automatic copper TX/RX pair correction
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

csetf100SpeedConfig 1.3.6.1.4.1.868.2.4.1.2.2.7.1.12
This variable allows the user to set the requested data transfer rate for this converter.
OBJECT-TYPE    
  INTEGER auto(1), mbps10(2), mbps100(3)  

csetf100Speed100Mbps 1.3.6.1.4.1.868.2.4.1.2.2.7.1.13
This variable reports the current data transfer rate for this converter.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

csetf100TPActivity 1.3.6.1.4.1.868.2.4.1.2.2.7.1.14
Network traffic indicator for Copper side of this device
OBJECT-TYPE    
  INTEGER activity(1), noActivity(2)  

csetf100FiberActivity 1.3.6.1.4.1.868.2.4.1.2.2.7.1.15
Network traffic indicator for Fiber side of this device
OBJECT-TYPE    
  INTEGER activity(1), noActivity(2)  

csetf100ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.7.1.16
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

csetf100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.7.1.17
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cgetf100Table 1.3.6.1.4.1.868.2.4.1.2.2.8
Sparse table containing one entry for each CGETF100 Gigabit Twisted-Pair to Fiber Ethernet Media Converter in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Cgetf100Entry

cgetf100Entry 1.3.6.1.4.1.868.2.4.1.2.2.8.1
One table entry per piece of management module information. Entry 'n' does not exist.
OBJECT-TYPE    
  Cgetf100Entry  

cgetf100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.8.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

cgetf100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.8.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

cgetf100Groups 1.3.6.1.4.1.868.2.4.1.2.2.8.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CGETF100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

cgetf100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.8.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cgetf100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.8.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), inactive(3)  

cgetf100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.8.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  

cgetf100ConnA 1.3.6.1.4.1.868.2.4.1.2.2.8.1.7
The style of Fiber connector built into this device
OBJECT-TYPE    
  CpsConnector  

cgetf100ConnB 1.3.6.1.4.1.868.2.4.1.2.2.8.1.8
The style of Copper connector built into this device
OBJECT-TYPE    
  CpsConnector  



cgetf100Fault 1.3.6.1.4.1.868.2.4.1.2.2.8.1.11
Value is yes(1) when either TPLink or FiberLink has value linkDown(2)
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cgetf100Enabled 1.3.6.1.4.1.868.2.4.1.2.2.8.1.12
When this variable is set to no(1), the device allows no traffic to pass.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cgetf100Pause 1.3.6.1.4.1.868.2.4.1.2.2.8.1.13
Enable/Disable control for the advertising of Pause capability on the copper interface. This MIB variable is retained for compatibility with older applications and firmware. If you have a current version of the CGETF100 device (which supports asymmetric pause), you should both read and write the MIB variable cgetf100PauseType(21) for complete monitoring and control of pause capability advertising. If you are using a current Transition Networks application, this is automatic. On all versions of the CGETF100 device, this MIB variable can be used to enable and disable advertising of symmetric pause. For current versions of the CGETF100, this variable reads enabled(1) any time any type of pause is enabled, and forces cgetf100PauseType(21) to symmetric(1) when changed from disabled(2) to enabled(1). On new versions of the CGETF100 device, when cgetf100FiberAutoNegot(19) has the value enabled(1), this variable takes on the read-only value enabled(1).
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cgetf100LinkPassThrough 1.3.6.1.4.1.868.2.4.1.2.2.8.1.14
Enable/Disable for Link Pass Through, a feature that causes loss of link on one side of a media converter to be passed through to the other side, so that upstream equipment can see the fault condition.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cgetf100FullDuplex 1.3.6.1.4.1.868.2.4.1.2.2.8.1.15
Controls advertizing of duplex capability for the copper side of the converter. When set to fullDuplex(1), the converter advertizes full duplex capability. When set to halfDuplex(2), the converter advertizes half duplex capability. The converter never advertizes both simultaneously. If the advertized setting is not supported by the remote, link cannot be established.
OBJECT-TYPE    
  INTEGER fullDuplex(1), halfDuplex(2)  

cgetf100ClockMaster 1.3.6.1.4.1.868.2.4.1.2.2.8.1.16
When yes(1), the converter is supplying clock to the twisted pair. When no(2), the remote supplies the clock.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cgetf100ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.8.1.17
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

cgetf100TPLength 1.3.6.1.4.1.868.2.4.1.2.2.8.1.18
Twisted-pair length estimated via the converter's internal Time Domain Reflectometer. 1 means less than 50 meters, 2 means 50 to 80 meters, 3 means 80 to 110 meters, 4 means 110 to 140 meters, and 5 means more than 140 meters.
OBJECT-TYPE    
  INTEGER ln-lt50(1), ln-50-80(2), ln-80-110(3), ln-110-140(4), ln-gt140(5)  

cgetf100FiberAutoNegot 1.3.6.1.4.1.868.2.4.1.2.2.8.1.19
Fiber port autonegotiation configuration.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cgetf100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.8.1.20
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cgetf100PauseType 1.3.6.1.4.1.868.2.4.1.2.2.8.1.21
Enable/Disable control for the advertising of Pause capability on the copper interface. This MIB variable is only functional on CGETF100 devices that support asymmetric pause (i.e. current versions). If your CGETF100 does not support asymmetric pause, this variable will return the read-only value notApplicable(5) regardless of any other factors. On current CGETF100 devices, selectable values for this variable are symmetric(1), asymRX(2) (asymmetric, pause frames flow towards the converter), asymTX(3) (asymmetric, pause frames flow towards the link partner), and disabled(4). Note: Changing cgetf100PauseType(21) to disabled(4) causes cgetf100Pause(13) to take on the value disabled(2). Changing cgetf100PauseType(21) to any selectable value other than disabled(4) causes cgetf100Pause(13) to take on the value enabled(1). If cgetf100FiberAutoNegot(19) has the value enabled(1), then this variable returns the read-only value all(10), which indicates that all advertised modes received from the twisted pair link partner are reflected back to the link partner. Otherwise, if cgetf100ConfigMode(17) has the value hardware(2), one of the following read-only values will be returned: symmetricRO(6) or disabledRO(9). The read-only values asymRXRO(7) and asymTXRO(8) are defined for future expansion.
OBJECT-TYPE    
  INTEGER symmetric(1), asymRX(2), asymTX(3), disabled(4), notApplicable(5), symmetricRO(6), asymRXRO(7), asymTXRO(8), disabledRO(9), all(10)  

csdtf100Table 1.3.6.1.4.1.868.2.4.1.2.2.9
Sparse table containing one entry for each CSDTF100 T1/E1 Copper to Fiber Media Converter in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Csdtf100Entry

csdtf100Entry 1.3.6.1.4.1.868.2.4.1.2.2.9.1
Status and configuration entries for a single CSDTF100
OBJECT-TYPE    
  Csdtf100Entry  

csdtf100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.9.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

csdtf100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.9.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

csdtf100Groups 1.3.6.1.4.1.868.2.4.1.2.2.9.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CSDTF100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

csdtf100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.9.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

csdtf100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.9.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), inactive(3)  

csdtf100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.9.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  

csdtf100ConnA 1.3.6.1.4.1.868.2.4.1.2.2.9.1.7
The style of Fiber connector built into this device
OBJECT-TYPE    
  CpsConnector  

csdtf100ConnB 1.3.6.1.4.1.868.2.4.1.2.2.9.1.8
The style of Copper connector built into this device
OBJECT-TYPE    
  CpsConnector  



csdtf100Fault 1.3.6.1.4.1.868.2.4.1.2.2.9.1.11
Value is yes(1) when either CopperLink or FiberLink has value linkDown(2)
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

csdtf100TAOSFiber 1.3.6.1.4.1.868.2.4.1.2.2.9.1.12
Transmit All Ones on Fiber as an error signal when Copper interface is down. When this error signal is transmitted, the AIS of the device on the other end is activated, if supported.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

csdtf100TAOSCopper 1.3.6.1.4.1.868.2.4.1.2.2.9.1.13
Transmit All Ones on Copper as an error signal when Fiber interface is down. When this error signal is transmitted, the AIS of the device on the other end is activated, if supported.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

csdtf100AISFiber 1.3.6.1.4.1.868.2.4.1.2.2.9.1.14
Alarm Indication Signal. When equal to alarm(1), this means that the other end has TAOS enabled and is currently transmitting an alarm condition.
OBJECT-TYPE    
  INTEGER alarm(1), normal(2)  

csdtf100AISCopper 1.3.6.1.4.1.868.2.4.1.2.2.9.1.15
Alarm Indication Signal. When equal to alarm(1), this means that the other end has TAOS enabled and is currently transmitting an alarm condition.
OBJECT-TYPE    
  INTEGER alarm(1), normal(2)  

csdtf100CopperLoopback 1.3.6.1.4.1.868.2.4.1.2.2.9.1.16
Enable loopback on the copper interface. Copper Loopback causes all data that is sent to the copper interface to be transmitted back out the copper interface. NOT SUPPORTED on initial version of the product.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

csdtf100CopperLongHaul 1.3.6.1.4.1.868.2.4.1.2.2.9.1.17
This variable indicates the current position of the device's long/short haul configuration switch.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

csdtf100T1E1 1.3.6.1.4.1.868.2.4.1.2.2.9.1.18
This variable indicates whether the current device is the T1 or the E1 version.
OBJECT-TYPE    
  INTEGER t1(1), e1(2)  

csdtf100ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.9.1.19
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

csdtf100TPCoax 1.3.6.1.4.1.868.2.4.1.2.2.9.1.20
Indicates the connector type installed on the copper interface. For E1 converters, this can be either Twisted Pair or Coax. For T1, it is always Twisted Pair.
OBJECT-TYPE    
  INTEGER tp(1), coax(2)  

csdtf100CopperLineBuildout 1.3.6.1.4.1.868.2.4.1.2.2.9.1.21
The characteristics of the copper interface
OBJECT-TYPE    
  INTEGER e13-0V120ohm(1), e12-37V75ohm(2), t1SH-DSX-0-133ANSIT1403(3), t1SH-DSX-133-266(4), t1SH-DSX-266-399(5), t1SH-DSX-399-533(6), t1SH-DSX-533-655(7), t1SH-DSX-6V(8), t1LH-0dB(9), t1LH-m7-5dB(10), t1LH-m15dB(11), t1LH-m22-5dB(12)  

csdtf100FiberLoopback 1.3.6.1.4.1.868.2.4.1.2.2.9.1.22
Enable loopback on the Fiber interface. Fiber Loopback causes all data that is sent to the Fiber interface to be transmitted back out the Fiber interface.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

csdtf100RmtSupported 1.3.6.1.4.1.868.2.4.1.2.2.9.1.23
Has the value yes(1) if this converter is capable of managing the media converter at the remote end of the fiber.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

csdtf100RmtDetected 1.3.6.1.4.1.868.2.4.1.2.2.9.1.24
Has the value yes(1) if management communcations have been established with a remote media converter. Always no(2) if TAOS is enabled or the remote converter does not support remote management.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

csdtf100RmtMRevision 1.3.6.1.4.1.868.2.4.1.2.2.9.1.25
Remote Marketing Revision. Same as csdtf100MRevision, only for the remote device.
OBJECT-TYPE    
  INTEGER  

csdtf100RmtSerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.9.1.26
Serial Number reported by remote device.
OBJECT-TYPE    
  INTEGER  

csdtf100RmtConnA 1.3.6.1.4.1.868.2.4.1.2.2.9.1.27
The style of Fiber connector reported by remote device.
OBJECT-TYPE    
  CpsConnector  

csdtf100RmtConnB 1.3.6.1.4.1.868.2.4.1.2.2.9.1.28
The style of Fiber connector reported by remote device.
OBJECT-TYPE    
  CpsConnector  



csdtf100RmtFault 1.3.6.1.4.1.868.2.4.1.2.2.9.1.31
Remote Fault status. Value is yes(1) when either CopperLink or FiberLink has value linkDown(2)
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

csdtf100RmtTAOSFiber 1.3.6.1.4.1.868.2.4.1.2.2.9.1.32
Remote Fiber TAOS configuration. Transmit All Ones on Fiber as an error signal when Copper interface is down. When this error signal is transmitted, the AIS of the device on the other end is activated, if supported.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

csdtf100RmtTAOSCopper 1.3.6.1.4.1.868.2.4.1.2.2.9.1.33
Remote Copper TAOS configuration. Transmit All Ones on Copper as an error signal when Fiber interface is down. When this error signal is transmitted, the AIS of the device on the other end is activated, if supported.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

csdtf100RmtAISFiber 1.3.6.1.4.1.868.2.4.1.2.2.9.1.34
Remote Fiber AIS status. Alarm Indication Signal. When equal to alarm(1), this means that the other end has TAOS enabled and is currently transmitting an alarm condition.
OBJECT-TYPE    
  INTEGER alarm(1), normal(2)  

csdtf100RmtAISCopper 1.3.6.1.4.1.868.2.4.1.2.2.9.1.35
Remote Copper AIS status. Alarm Indication Signal. When equal to alarm(1), this means that the other end has TAOS enabled and is currently transmitting an alarm condition.
OBJECT-TYPE    
  INTEGER alarm(1), normal(2)  

csdtf100RmtCopperLoopback 1.3.6.1.4.1.868.2.4.1.2.2.9.1.36
Remote Copper Loopback configuration. Enable loopback on the copper interface. Copper Loopback causes all data that is sent to the copper interface to be transmitted back out the copper interface. NOT SUPPORTED on initial version of the product.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

csdtf100RmtCopperLongHaul 1.3.6.1.4.1.868.2.4.1.2.2.9.1.37
This variable indicates the current position of the remote device's Short/Long haul configuration switch.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

csdtf100RmtConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.9.1.38
Remote Configuration Mode. This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

csdtf100RmtTPCoax 1.3.6.1.4.1.868.2.4.1.2.2.9.1.39
Indicates the connector type installed on the remote copper interface. For E1 converters, this can be either Twisted Pair or Coax. For T1, it is always Twisted Pair.
OBJECT-TYPE    
  INTEGER tp(1), coax(2)  

csdtf100RmtCopperLineBuildout 1.3.6.1.4.1.868.2.4.1.2.2.9.1.40
The electrical characteristics of the remote Copper interface. Values are the same as the values for csdtf100CopperLineBuildout(21)
OBJECT-TYPE    
  INTEGER e13-0V120ohm(1), e12-37V75ohm(2), t1SH-DSX-0-133ANSIT1403(3), t1SH-DSX-133-266(4), t1SH-DSX-266-399(5), t1SH-DSX-399-533(6), t1SH-DSX-533-655(7), t1SH-DSX-6V(8), t1LH-0dB(9), t1LH-m7-5dB(10), t1LH-m15dB(11), t1LH-m22-5dB(12)  

csdtf100RmtFiberLoopback 1.3.6.1.4.1.868.2.4.1.2.2.9.1.41
Enable loopback on the remote Fiber interface. Fiber Loopback causes all data that is sent to the Fiber interface to be transmitted back out the Fiber interface.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

csdtf100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.9.1.42
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cpsmp110Table 1.3.6.1.4.1.868.2.4.1.2.2.10
Sparse table containing one entry for each CPSMP110 IFO (Instant Fail-Over) Power Supply in the stack. indexed by sub-device index, cabinet serial number, and slot. Note that some columns of this table support multiple subdevices, and some do not. For example, there is exactly one SerialNumber for each CPSMP110. No subdevices exist, so the placeholder value 1 is used as the subdevice index. However, a CPSMP110 has zero or more current sensors, which (if they exist) are indexed as different subdevices, starting with 1. Columns with subdevices have names ending in 'Tbl'
OBJECT-TYPE    
  SEQUENCE OF  
    Cpsmp110Entry

cpsmp110Entry 1.3.6.1.4.1.868.2.4.1.2.2.10.1
Status and configuration entries for a single CPSMP100
OBJECT-TYPE    
  Cpsmp110Entry  

cpsmp110SubDeviceIndex 1.3.6.1.4.1.868.2.4.1.2.2.10.1.1
Generally, individual devices in this MIB are distinguished by BiaIndex and SlotIndex. This device differs from many in that it contains multiple subdevices (in this case, fans, temperature sensors, current sensors, and power supplies). The number of subdevices varies with the manufactured configuration. Subdevices within devices are indexed by BiaIndex, SlotIndex, and SubDeviceIndex. When the subdevice column is read from the table, the value '1' is always returned.
OBJECT-TYPE    
  INTEGER  

cpsmp110BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.10.1.2
The serial number (BIA) of the cabinet in which the device is installed. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER  

cpsmp110SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.10.1.3
The slot in which the device is installed. Power Supplies occupy special slots numbered 125 and higher. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER  

cpsmp110Groups 1.3.6.1.4.1.868.2.4.1.2.2.10.1.4
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CPSMP110' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]' There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  DisplayString  

cpsmp110MRevision 1.3.6.1.4.1.868.2.4.1.2.2.10.1.5
The marketing revision of this device. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER  

cpsmp110CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.10.1.6
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cpsmp110SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.10.1.7
The serial number of this device. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER  

cpsmp110ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.10.1.8
This device may have a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

cpsmp110MasterTempFault 1.3.6.1.4.1.868.2.4.1.2.2.10.1.9
The master temperature fault indicator for this device. A value of yes(1) indicates that at least one temperature sensor encountered a fault condition since the last time the device was queried by the management module. The statuses of individual temperature sensors can be found in cpsmp110TemperatureTbl. Note that in the unusual case that a sensor spikes (i.e. encounters a fault, and then quickly returns to normal), it will be difficult to determine which sensor faulted. However, the fact that any sensor faulted is sufficient cause to examine the cabinet further. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsmp110MasterCurrentFault 1.3.6.1.4.1.868.2.4.1.2.2.10.1.10
The master current fault indicator for this device. A value of yes(1) indicates that at least one current sensor encountered a fault condition since the last time the device was queried by the management module. The statuses of individual current sensors can be found in cpsmp110CurrentTbl. Note that in the unusual case that a sensor spikes (i.e. encounters a fault, and then quickly returns to normal), it will be difficult to determine which sensor faulted. However, the fact that any sensor faulted is sufficient cause to examine the cabinet further. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsmp110MasterFanFault 1.3.6.1.4.1.868.2.4.1.2.2.10.1.11
The master fan fault indicator for this device. A value of yes(1) indicates that at least one fan current sensor encountered a fault condition since the last time the device was queried by the management module. The statuses of individual fan current sensors can be found in cpsmp110FanStatusTbl. Note that in the unusual case that a sensor spikes (i.e. encounters a fault, and then quickly returns to normal), it will be difficult to determine which sensor faulted. However, the fact that any sensor faulted is sufficient cause to examine the cabinet further. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsmp110FirmwareRevision 1.3.6.1.4.1.868.2.4.1.2.2.10.1.12
The firmware revision level for this device. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER  

cpsmp110PSSupplyTbl 1.3.6.1.4.1.868.2.4.1.2.2.10.1.13
The supply voltage that this unit is designed to accept. If AC(1), the supply accepts VAC. If DC(2), the supply accepts. A single CPSMP110 control unit can support multiple subdevices of this type. There will be one entry per subdevice.
OBJECT-TYPE    
  INTEGER ac(1), dc(2), reserved3(3), reserved4(4), notInstalled(5)  

cpsmp110PSRoleTbl 1.3.6.1.4.1.868.2.4.1.2.2.10.1.14
Some power supplies support a Master/Slave relationship: When one power supply is set to master(1) and the other is set to slave(2), the master will supply all power to the cabinet, and the slave will take over if the master stops supplying power. This is useful when (for example) one supply is attached to a wall socket and the other to a battery backup. The cabinet can be directed to only draw power from batteries when there is no alternative. When both power supplies are set to master(1), the results are determined automatically. WARNING: It is up to the system administrator to ensure that at least one power supply is set to master(1). It is illegal to set all power supplies to slave(2). If this occurs, the cabinet may lose all power under certain circumstances, even if power is available. In some cases, the Master/Slave relationship cannot be configured via management; it is determined by other means, such as the slot locations in which the supplies are installed, or switches on the supplies. In this case, attempts to change the value of this variable from management will be ignored. The ConfigMode variable will have the value hardware(2) in this case. If a supply does not support (or can disable) Master/Slave functionality, the value shared(3) is returned. In this case, all ready power supplies share the load evenly. A single CPSMP110 control unit can support multiple subdevices of this type.
OBJECT-TYPE    
  INTEGER master(1), slave(2), shared(3), notInstalled(4)  

cpsmp110PSReadyTbl 1.3.6.1.4.1.868.2.4.1.2.2.10.1.15
The readiness of this power supply module. A value of yes(1) indicates the module is ready to supply power to the cabinet. A value of no(2) indicates that the supply has no output power to offer, either because it is malfunctioning or because it has no input power. A single CPSMP110 control unit can support multiple subdevices of this type.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsmp110PSInUseTbl 1.3.6.1.4.1.868.2.4.1.2.2.10.1.16
The use status of this power supply module. A value of yes(1) indicates the module is supplying power to the cabinet. This variable is useful in configurations where master/slave role functionality is supported to determine whether the Master or the Slave is active. In shared configurations, the value of PSReadyTbl is strongly preferred as an indication of the status of the supply. A single CPSMP110 control unit can support multiple subdevices of this type.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsmp110TemperatureTbl 1.3.6.1.4.1.868.2.4.1.2.2.10.1.17
The temperature, in tenths of degrees centigrade, read by this temperature sensor. A single CPSMP110 control unit can support multiple subdevices of this type.
OBJECT-TYPE    
  INTEGER  

cpsmp110CurrentTbl 1.3.6.1.4.1.868.2.4.1.2.2.10.1.18
The current, in milliwatts, read by this current sensor. A single CPSMP110 control unit can support multiple subdevices of this type.
OBJECT-TYPE    
  INTEGER  

cpsmp110FanStatusTbl 1.3.6.1.4.1.868.2.4.1.2.2.10.1.19
The status of a fan. A value of fault(2) indicates that the control unit has detected a problem with the fan, usually that it is is drawing excessive current. A single CPSMP110 control unit can support multiple subdevices of this type.
OBJECT-TYPE    
  INTEGER ok(1), fault(2), notInstalled(3)  

cpsmp110TempFaultTbl 1.3.6.1.4.1.868.2.4.1.2.2.10.1.20
Each entry in this column corresponds to an entry with the same indices in cpsmp110TemperatureTable. It indicates whether or not the temperature read by the sensor is within the acceptable range. A single CPSMP110 control unit can support multiple subdevices of this type.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsmp110CurrFaultTbl 1.3.6.1.4.1.868.2.4.1.2.2.10.1.21
Each entry in this column corresponds to an entry with the same indices in cpsmp110CurrentTable. It indicates whether or not the current read by the sensor is within the acceptable range. A single CPSMP110 control unit can support multiple subdevices of this type.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsmp110PSCount 1.3.6.1.4.1.868.2.4.1.2.2.10.1.22
The maximum number of power supplies supported in this configuration.
OBJECT-TYPE    
  INTEGER  

cpsmp110TempSensorCount 1.3.6.1.4.1.868.2.4.1.2.2.10.1.23
The number of temperature sensors supported in this device.
OBJECT-TYPE    
  INTEGER  

cpsmp110CurrSensorCount 1.3.6.1.4.1.868.2.4.1.2.2.10.1.24
The number of current sensors supported in this device.
OBJECT-TYPE    
  INTEGER  

cpsmp110FanCount 1.3.6.1.4.1.868.2.4.1.2.2.10.1.25
The number of fans supported in this device.
OBJECT-TYPE    
  INTEGER  

cpsmp110CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.10.1.26
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cbftf100Table 1.3.6.1.4.1.868.2.4.1.2.2.11
Sparse table containing one entry for each CBFTF100 switch in the stack. Indexed by sub-device index, cabinet serial number, and slot. Note that some columns of this table support multiple subdevices, and some do not. For example, there is exactly one SerialNumber for each CBFTF100. No subdevices exist, so the placeholder value 1 is used as the subdevice index. However, a CBFTF100 has multiple switch ports, which are indexed as different subdevices, starting with 1. Columns with subdevices have names ending in 'Tbl'
OBJECT-TYPE    
  SEQUENCE OF  
    Cbftf100Entry

cbftf100Entry 1.3.6.1.4.1.868.2.4.1.2.2.11.1
Status and configuration entries for a single CBFTF100
OBJECT-TYPE    
  Cbftf100Entry  

cbftf100SubDeviceIndex 1.3.6.1.4.1.868.2.4.1.2.2.11.1.1
Generally, individual devices in this MIB are distinguished by BiaIndex and SlotIndex. This device differs from many in that it contains multiple subdevices (in this case, switch ports). The number of subdevices varies with the manufactured configuration. Subdevices within devices are indexed by BiaIndex, SlotIndex, and SubDeviceIndex. When the subdevice column is read from the table, the value '1' is always returned.
OBJECT-TYPE    
  INTEGER  

cbftf100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.11.1.2
The serial number (BIA) of the cabinet in which the device is installed. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER  

cbftf100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.11.1.3
The slot in which the device is installed. Power Supplies occupy special slots numbered 125 and higher. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER  

cbftf100Groups 1.3.6.1.4.1.868.2.4.1.2.2.11.1.4
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'cbftf100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]' There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  DisplayString  

cbftf100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.11.1.5
The marketing revision of this device. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER  

cbftf100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.11.1.6
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cbftf100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.11.1.7
The serial number of this device. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER  

cbftf100ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.11.1.8
This device may have a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

cbftf100FirmwareRevision 1.3.6.1.4.1.868.2.4.1.2.2.11.1.9
The firmware revision level for this device. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER  

cbftf100SelfTestFailed 1.3.6.1.4.1.868.2.4.1.2.2.11.1.10
This variable indicates the status of the pass/fail power on test. If the power on test fails, normal operation of this device is probably not possible.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cbftf100SpanningTree 1.3.6.1.4.1.868.2.4.1.2.2.11.1.11
This variable allows the agent to enable or disable Spanning Tree if it is supported. Not all versions of the hardware support Spanning Tree.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

cbftf100MirrorCfg 1.3.6.1.4.1.868.2.4.1.2.2.11.1.12
Global enable/disable for mirror port functionality. When this variable is set to disabled, the values of cbftf100MirrorSelTbl, cbftf100MirrorInTbl, and cbftf100MirrorOutTbl are ignored.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

cbftf100SACMasterCfg 1.3.6.1.4.1.868.2.4.1.2.2.11.1.13
Global enable/disable for Source Address Change detection functionality. When this variable is set to disabled the values in cbtf100SACCfgTbl are ignored.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cbftf100FormFactor 1.3.6.1.4.1.868.2.4.1.2.2.11.1.14
A code corresponding to a physical configuration of the product. This code indicates the number of slots occupied and the number of physical connectors present. In the labels for the values above, s indicates the number of slots occupied, W is a count of Wide port positions (which can built as almost any type of connector), and N is a count of narrow port positions (which are typically twisted pair ports). The lowercase letter at the end differentiates different form factors that would otherwise have identical descriptions under this limited scheme.
OBJECT-TYPE    
  INTEGER s1W2a(1), s1W1N2a(2), s1W1N1a(3), s2W2N4a(4), s2W1N5a(5)  

cbftf100AutoNegotTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.15
Enables or disables autonegtiation of link speed and duplex for twisted pair ports. Not supported on Fiber ports. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

cbftf100FullDuplexTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.16
In most cases this is a configuration setting that controls the duplex mode; fullDuplex is full duplex and halfDuplex is half duplex. On twisted pair ports with autonegotiation enabled, this is a status indication showing the duplex value decided upon during the negotiation. When link is down, autonegotiation has not been completed yet, and the duplex setting is therefore unknown and the value is negotiating(3). There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER fullDuplex(1), halfDuplex(2), negotiating(3)  

cbftf100100MbpsTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.17
In most cases this is a configuration setting that controls the link speed. On twisted pair ports with autonegotiation enabled, this is a status indication showing the link speed decided upon during negotiation. When link is down, autonegotiation has not been completed yet, and the link speed is therefore unknown and is negotiating(3). This variable is an indicator only for fiber ports; all fiber ports report mbps100(1) at all times. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER mbps100(1), mbps10(2), negotiating(3)  

cbftf100Adv10HDXTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.18
This configuration setting controls whether or not each port advertises willingness to connect at 10Mbps, half duplex. This setting is not supported on fiber ports, and is ignored when autonegotiation is disabled. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

cbftf100Adv10FDXTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.19
This configuration setting controls whether or not each port advertises willingness to connect at 10Mbps, full duplex. This setting is not supported on fiber ports, and is ignored when autonegotiation is disabled. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

cbftf100Adv100HDXTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.20
This configuration setting controls whether or not each port advertises willingness to connect at 100Mbps, half duplex. This setting is not supported on fiber ports, and is ignored when autonegotiation is disabled. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

cbftf100Adv100FDXTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.21
This configuration setting controls whether or not each port advertises willingness to connect at 100Mbps, full duplex. This setting is not supported on fiber ports, and is ignored when autonegotiation is disabled. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

cbftf100CrossTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.22
Configuration setting for copper TX/RX pair correction. A setting of auto(1) causes the port to automatically correct TX/RX pairs if necessary. If autonegotiation is disabled on the port, the auto(1) setting is not supported. A setting of mdi(2) causes the TX/RX pairs to be passed straight through with no correction. A setting of mdix(3) causes the TX/RX pairs to be swapped. This setting is supprted for copper ports only; a read-only value of notSupported(4) is returned for fiber ports. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER auto(1), mdi(2), mdix(3), notSupported(4)  

cbftf100PauseCfgTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.23
The Pause feature allows Ethernet MACs that support it to send data pacing 'Pause' messages to each other. A setting of enabled(1) causes this port to advertise pause capability and a setting of disabled(2) disables pause capability advertising. On fiber ports, a read-only value of notSupported(3) is returned. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

cbftf100PauseStatTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.24
The Pause feature allows Ethernet MACs that support it to send data pacing 'Pause' messages to each other. A value of paused(1) indicated the port is in a paused state, and a value of normal(2) indicates the port is operating normally. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER paused(1), normal(2)  

cbftf100FarEndFaultTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.25
When Far End Fault is set to enabled(1), a loss of link on receive will cause the transmitter to shut down, in order to inform the device at the far end of the link that a fault has occurred. Far End Fault is only supported on fiber ports. A read-only value of notSupported(3) is returned for copper ports. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

cbftf100ConnectorTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.26
The style of connectors built into each port of this device. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  CpsConnector  

cbftf100SACCfgTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.27
This configuration setting controls whether changes in source MAC address are reported. When set to enabled(1), a change in MAC address will result in a momentary change in the value of SACStatTbl from same(2) to changed(1) and back, and the transmission of a trap, if the management module is so configured. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cbftf100SACStatTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.28
This status value indicates whether or not the source MAC address attached to this port changed in the last polling period. This value tends to change quite quickly; therefore, the 'ERROR' traps that are sent when SAC is detected are a much more reliable indicator. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER changed(1), same(2)  

cbftf100MirrorSelTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.29
This configuration setting allows a mirror port to be selected. The selected port will re-transmit copies of all packets transmitted on ports whose MirrorOutTbl value is set to mirrorOut(1), and will also transmit copies of all packets received by all ports whose MirrorInTbl value is set to mirrorIn(1). It is recommended that a maximum of one MirrorSelTbl, one MirrorInTbl, and one MirrorOutTbl port be selected at once, since the switch may have trouble handling the traffic that can result from other configurations. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER mirror(1), normal(2)  

cbftf100MirrorInTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.30
This configuration setting allows a mirror source port to be selected. All packets received on each port with a MirrorInTbl setting of mirrorIn(1) will be retransmitted on all ports whose MirrorSelTbl setting is mirror(1). It is recommended that a maximum of one MirrorSelTbl, one MirrorInTbl, and one MirrorOutTbl port be selected at once, since the switch may have trouble handling the traffic that can result from other configurations. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER mirrorIn(1), normal(2)  

cbftf100MirrorOutTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.31
This configuration setting allows a mirror source port to be selected. All packets transmitted on each port with a MirrorInTbl setting of mirrorOut(1) will be retransmitted on all ports whose MirrorSelTbl setting is mirror(1). It is recommended that a maximum of one MirrorSelTbl, one MirrorInTbl, and one MirrorOutTbl port be selected at once, since the switch may have trouble handling the traffic that can result from other configurations. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER mirrorOut(1), normal(2)  

cbftf100LinkTbl 1.3.6.1.4.1.868.2.4.1.2.2.11.1.32
This table contains the link status of each port in the switch. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

cbftf100PortCount 1.3.6.1.4.1.868.2.4.1.2.2.11.1.33
A count of the switch ports in this device. i.e. the maximum subdevice index supported by this switch.
OBJECT-TYPE    
  INTEGER  

cbftf100LinkPassThrough 1.3.6.1.4.1.868.2.4.1.2.2.11.1.34
If Link Passthrough is enabled on a port, loss of link on the opposite port will be propegated through to this port so that the switch does not prevent one end device from detecting loss of link on the opposite end device. Far end fault is only supported on copper ports and only in switch configurations that have exactly two ports.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

cbftf100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.11.1.35
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cbftf100RedundantPath 1.3.6.1.4.1.868.2.4.1.2.2.11.1.36
This variable shows the status of the redundant fiber capability. If the value is enabled(1), this means that the hardware switch to enable redundant fiber is on, and the two fiber ports on the device are presumed to be connected to the same remote device. Even if both fibers have link, traffic flows to and from that device through only one of the two fiber pairs at once. This provides a redundant path should one of the fibers be compromised. If the value is disabled(2), the hardware switch to enable redundant fiber is off, and the two fiber ports on the device pass traffic normally (i.e. independently and simultaneously). If the value is notSupported(3), the device does not have redundant fiber capability.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

cetct100Table 1.3.6.1.4.1.868.2.4.1.2.2.12
Sparse table containing one entry for each CETCT100 10Mbps Twisted-Pair to Fiber Ethernet Media Converter in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Cetct100Entry

cetct100Entry 1.3.6.1.4.1.868.2.4.1.2.2.12.1
Status and configuration entries for a single CETCT100
OBJECT-TYPE    
  Cetct100Entry  

cetct100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.12.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

cetct100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.12.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

cetct100Groups 1.3.6.1.4.1.868.2.4.1.2.2.12.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CETCT100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

cetct100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.12.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cetct100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.12.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cetct100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.12.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  

cetct100ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.12.1.7
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

cetct100FirmwareRevision 1.3.6.1.4.1.868.2.4.1.2.2.12.1.8
The firmware revision level for this device.
OBJECT-TYPE    
  INTEGER  


cetct100Collision 1.3.6.1.4.1.868.2.4.1.2.2.12.1.10
This status variable indicates whether or not an Ethernet collision occurred during the most recent polling cycle.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cetct100CoaxActivity 1.3.6.1.4.1.868.2.4.1.2.2.12.1.11
This status variable indicates whether or not Ethernet traffic was detected on the Coax interface during the most recent polling cycle.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cetct100TPActivity 1.3.6.1.4.1.868.2.4.1.2.2.12.1.12
This status variable indicates whether or not Ethernet traffic was detected on the Twisted Pair interface during the most recent polling cycle.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cetct100CollisionsPerMinute 1.3.6.1.4.1.868.2.4.1.2.2.12.1.13
The number of Ethernet collisions that occurred during the most recently completed measured minute. Every 60 seconds, the device moves its previous collision count into this variable, and restarts the counter at zero.
OBJECT-TYPE    
  INTEGER  

cetct100CollisionsPerHour 1.3.6.1.4.1.868.2.4.1.2.2.12.1.14
The number of Ethernet collisions that occurred during the most recently completed measured hour. Every 60 minutes, the device moves its previous collision count into this variable, and restarts the counter at zero.
OBJECT-TYPE    
  INTEGER  

cetct100ConnA 1.3.6.1.4.1.868.2.4.1.2.2.12.1.15
The style of media connector built into this device.
OBJECT-TYPE    
  CpsConnector  

cetct100ConnB 1.3.6.1.4.1.868.2.4.1.2.2.12.1.16
The style of media connector built into this device.
OBJECT-TYPE    
  CpsConnector  

cetct100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.12.1.17
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

ccscf100Table 1.3.6.1.4.1.868.2.4.1.2.2.13
Sparse table containing one entry for each ccscf100 T3/E3 Copper to Fiber Media Converter in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Ccscf100Entry

ccscf100Entry 1.3.6.1.4.1.868.2.4.1.2.2.13.1
Status and configuration entries for a single ccscf100
OBJECT-TYPE    
  Ccscf100Entry  

ccscf100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.13.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

ccscf100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.13.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

ccscf100Groups 1.3.6.1.4.1.868.2.4.1.2.2.13.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'ccscf100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

ccscf100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.13.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

ccscf100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.13.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), inactive(3)  

ccscf100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.13.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  

ccscf100ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.13.1.7
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  



ccscf100AISFiber 1.3.6.1.4.1.868.2.4.1.2.2.13.1.10
Alarm Indication Signal. When equal to alarm(1), this means that the other end has TAOS enabled and is currently transmitting an alarm condition.
OBJECT-TYPE    
  INTEGER alarm(1), normal(2)  

ccscf100AISCopper 1.3.6.1.4.1.868.2.4.1.2.2.13.1.11
Alarm Indication Signal. When equal to alarm(1), this means that the other end has TAOS enabled and is currently transmitting an alarm condition.
OBJECT-TYPE    
  INTEGER alarm(1), normal(2)  

ccscf100DS3LineBuildout 1.3.6.1.4.1.868.2.4.1.2.2.13.1.12
The characteristics of the copper interface
OBJECT-TYPE    
  INTEGER boost(1), normal(2), notSupported(3)  

ccscf100E3DS3 1.3.6.1.4.1.868.2.4.1.2.2.13.1.13
This variable indicates whether the current device is the T1 or the E1 version.
OBJECT-TYPE    
  INTEGER e3(1), ds3(2)  

ccscf100CopperLoopback 1.3.6.1.4.1.868.2.4.1.2.2.13.1.14
Enable loopback on the copper interface.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ccscf100FiberLoopback 1.3.6.1.4.1.868.2.4.1.2.2.13.1.15
Enable loopback on the copper interface.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ccscf100ConnA 1.3.6.1.4.1.868.2.4.1.2.2.13.1.16
The style of Fiber connector built into this device
OBJECT-TYPE    
  CpsConnector  

ccscf100ConnB 1.3.6.1.4.1.868.2.4.1.2.2.13.1.17
The style of Copper connector built into this device
OBJECT-TYPE    
  CpsConnector  

ccscf100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.13.1.18
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cfetf105Table 1.3.6.1.4.1.868.2.4.1.2.2.14
Sparse table containing one entry for each CFTEF105 100Mbps Twisted-Pair to Fiber Ethernet Media Converter in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Cfetf105Entry

cfetf105Entry 1.3.6.1.4.1.868.2.4.1.2.2.14.1
Status and configuration entries for a single CFETF105
OBJECT-TYPE    
  Cfetf105Entry  

cfetf105BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.14.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

cfetf105SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.14.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

cfetf105Groups 1.3.6.1.4.1.868.2.4.1.2.2.14.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CFETF105' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

cfetf105MRevision 1.3.6.1.4.1.868.2.4.1.2.2.14.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cfetf105CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.14.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cfetf105SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.14.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  

cfetf105ConnA 1.3.6.1.4.1.868.2.4.1.2.2.14.1.7
The style of Fiber connector built into this device
OBJECT-TYPE    
  CpsConnector  

cfetf105ConnB 1.3.6.1.4.1.868.2.4.1.2.2.14.1.8
The style of Copper connector built into this device
OBJECT-TYPE    
  CpsConnector  



cfetf105AutoNegot 1.3.6.1.4.1.868.2.4.1.2.2.14.1.11
Enable/Disable Autonegotiation
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cfetf105LinkPassThrough 1.3.6.1.4.1.868.2.4.1.2.2.14.1.12
Enable/Disable for Link Pass Through, a feature that causes loss of link on one side of a media converter to be passed through to the other side, so that upstream equipment can see the fault condition.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cfetf105AutoCross 1.3.6.1.4.1.868.2.4.1.2.2.14.1.13
Enable/Disable for automatic copper TX/RX pair correction
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cfetf105TPActivity 1.3.6.1.4.1.868.2.4.1.2.2.14.1.14
Network traffic indicator for Copper side of this device
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

cfetf105FiberActivity 1.3.6.1.4.1.868.2.4.1.2.2.14.1.15
Network traffic indicator for Fiber side of this device
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

cfetf105ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.14.1.16
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

cfetf105CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.14.1.17
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

smacf100PTable 1.3.6.1.4.1.868.2.4.1.2.2.15
Sparse table containing one entry for each SMACF100P virtual slide-in device. This table dexcribes ONE port on a SMACFxxx colony switch
OBJECT-TYPE    
  SEQUENCE OF  
    Smacf100PEntry

smacf100PEntry 1.3.6.1.4.1.868.2.4.1.2.2.15.1
Status and configuration entries for a single SMACF100P
OBJECT-TYPE    
  Smacf100PEntry  

smacf100PSubDeviceIndex 1.3.6.1.4.1.868.2.4.1.2.2.15.1.1
Generally, individual devices in this MIB are distinguished by BiaIndex and SlotIndex. This device differs from many in that it contains multiple subdevices. The number of subdevices varies with the manufactured configuration. Subdevices within devices are indexed by BiaIndex, SlotIndex, and SubDeviceIndex. When the subdevice column is read from the table, the value '1' is always returned.
OBJECT-TYPE    
  INTEGER  

smacf100PBiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.15.1.2
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

smacf100PSlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.15.1.3
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

smacf100PGroups 1.3.6.1.4.1.868.2.4.1.2.2.15.1.4
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'SMACF100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

smacf100PCfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.15.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

smacf100PConnA 1.3.6.1.4.1.868.2.4.1.2.2.15.1.6
The style of Fiber or Copper connector built into this device
OBJECT-TYPE    
  CpsConnector  


smacf100P100Mbps 1.3.6.1.4.1.868.2.4.1.2.2.15.1.8
Communication speed for this port.
OBJECT-TYPE    
  INTEGER mbps100(1), mbps10(2)  

smacf100PFullDuplex 1.3.6.1.4.1.868.2.4.1.2.2.15.1.9
In most cases this is a configuration setting that controls the duplex mode; fullDuplex is full duplex and halfDuplex is half duplex. On twisted pair ports with autonegotiation enabled, this is a status indication showing the duplex value decided upon during the negotiation. When link is down, autonegotiation has not been completed yet, and the duplex setting is therefore unknown and the value is negotiating(3).
OBJECT-TYPE    
  INTEGER fullDuplex(1), halfDuplex(2), negotiating(3)  

smacf100PSACStat 1.3.6.1.4.1.868.2.4.1.2.2.15.1.10
This status value indicates whether or not the source MAC address attached to this port changed in the last polling period. This value tends to change quite quickly; therefore, the 'ERROR' traps that are sent when SAC is detected are a much more reliable indicator.
OBJECT-TYPE    
  INTEGER changed(1), same(2)  

smacf100PEnabled 1.3.6.1.4.1.868.2.4.1.2.2.15.1.11
Status of of this Port. A value of yes(1) indicates this port is 'enabled'. A value of no(2) indicates this port is 'disabled'.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

smacf100PAutoNegot 1.3.6.1.4.1.868.2.4.1.2.2.15.1.12
Enables or disables autonegtiation of link speed and duplex for twisted pair ports. Not supported on Fiber ports.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

smacf100PAdv10HDX 1.3.6.1.4.1.868.2.4.1.2.2.15.1.13
This configuration setting controls whether or not each port advertises willingness to connect at 10Mbps, half duplex. This setting is not supported on fiber ports, and is ignored when autonegotiation is disabled.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

smacf100PAdv10FDX 1.3.6.1.4.1.868.2.4.1.2.2.15.1.14
This configuration setting controls whether or not each port advertises willingness to connect at 10Mbps, full duplex. This setting is not supported on fiber ports, and is ignored when autonegotiation is disabled.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

smacf100PAdv100HDX 1.3.6.1.4.1.868.2.4.1.2.2.15.1.15
This configuration setting controls whether or not each port advertises willingness to connect at 100Mbps, half duplex. This setting is not supported on fiber ports, and is ignored when autonegotiation is disabled.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

smacf100PAdv100FDX 1.3.6.1.4.1.868.2.4.1.2.2.15.1.16
This configuration setting controls whether or not each port advertises willingness to connect at 100Mbps, full duplex. This setting is not supported on fiber ports, and is ignored when autonegotiation is disabled.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

smacf100PSTPState 1.3.6.1.4.1.868.2.4.1.2.2.15.1.17
Port spanning tree state.
OBJECT-TYPE    
  INTEGER notSupported(1), disabled(2), blocking(3), listening(4), learning(5), forwarding(6)  

smacf100PLastMAC 1.3.6.1.4.1.868.2.4.1.2.2.15.1.18
Last MAC Address this port communicated with.
OBJECT-TYPE    
  MacAddress  

smacf100PFarEndFaultCfg 1.3.6.1.4.1.868.2.4.1.2.2.15.1.19
Far end fault configuration of this Port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

smacf100PFarEndFaultStat 1.3.6.1.4.1.868.2.4.1.2.2.15.1.20
Far end fault status of this port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

smacf100PTxOctets 1.3.6.1.4.1.868.2.4.1.2.2.15.1.21
The number of bytes of data transmitted through this interface.
OBJECT-TYPE    
  INTEGER  

smacf100PWrapTxOctets 1.3.6.1.4.1.868.2.4.1.2.2.15.1.22
The number of times that the unsigned 32-bit smacf100PTxOctets(21) MIB variable has wrapped.
OBJECT-TYPE    
  INTEGER  

smacf100PRxOctets 1.3.6.1.4.1.868.2.4.1.2.2.15.1.23
The number of bytes of data received through this interface.
OBJECT-TYPE    
  INTEGER  

smacf100PWrapRxOctets 1.3.6.1.4.1.868.2.4.1.2.2.15.1.24
The number of times that the unsigned 32-bit smacf100PRxOctets(23) MIB variable has wrapped.
OBJECT-TYPE    
  INTEGER  

smacf100PSACCfg 1.3.6.1.4.1.868.2.4.1.2.2.15.1.25
Source Address Change detection configuration. Enables or Disables the generation of traps related to source address change for this port. When disabled, the smacf100PSACStat(10) variable always reads no.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

smacf100PBlockMgmt 1.3.6.1.4.1.868.2.4.1.2.2.15.1.26
Through this variable and others, the SMACF100 supports port- based VLANs. The SMACF100 will pass tags for IEEE 802.3ac VLANs, but will neither insert nor strip them. When this variable is set to block(1), this port may neither transmit packets to nor receive packets from management entities within this switch, i.e. the reporting unit (present in every SMACF100) and the management module (present in SMACF100 Main Management Units). This feature is intended to block traffic between particular Ethernet interfaces inside a single switch; it cannot identify or block management traffic from external sources. A single port is selected for configuration via the slot index. The subdevice index for this variable must always be 1. The logical soundness of VLAN rules cannot be validated. If you set smacf100PBlockMgmt(26) to block(1) on a port that provides a path between a reporting unit and its management module, or between a management module and its Network Management Station, you will be unable to manage the SMACF100 until the situation is rectified (by recabling to work around the misconfiguration, or by resetting the SMACF100 to factory defaults via the serial port).
OBJECT-TYPE    
  INTEGER block(1), pass(2)  

smacf100PBlockPort 1.3.6.1.4.1.868.2.4.1.2.2.15.1.27
Through this variable and others, the SMACF100 supports port- based VLANs. The SMACF100 will pass tags for IEEE 802.3ac VLANs, but will neither insert nor strip them. This table allows the network administrator to block traffic between pairs of ports within a single SMACF100. A pair of ports is selected for configuration by specifying a slot index and a subdevice index. The order in which the two ports are specified is unimportant, the effects of the configuration are identical on both ports. Each port has a smacf100PBlockPort(27) entry for every other port. So, communication between ports and in cabinet serial can be blocked by setting either smacf100PBlockPort... or smacf100PBlockPort... to block(1). Attempts to prevent a port from communicating with itself are ignored. Beyond that, the logical soundness of VLAN rules cannot be validated. There is one entry per subdevice, and one subdevice per port on the SMACF100.
OBJECT-TYPE    
  INTEGER block(1), pass(2)  

smacf100PTxDropPkts 1.3.6.1.4.1.868.2.4.1.2.2.15.1.28
This counter is incremented every time a transmit packet is dropped due to lack of resources (e.g. transmit FIFO underflow), or an internal MAC sublayer transmit error occurs that is not counted by either TxLateCollision or TxExcessiveCollision counters.
OBJECT-TYPE    
  INTEGER  

smacf100PTxBroadcastPkts 1.3.6.1.4.1.868.2.4.1.2.2.15.1.29
The number of good packets transmitted by this port that are directed to a broadcast address. This counter includes neither errored broadcast packets nor valid multicast packets.
OBJECT-TYPE    
  INTEGER  

smacf100PTxMulticastPkts 1.3.6.1.4.1.868.2.4.1.2.2.15.1.30
The number of good packets transmitted by this port that are directed to a multicast address. This counter includes neither errored multicast packets nor valid broadcast packets.
OBJECT-TYPE    
  INTEGER  

smacf100PTxUnicastPkts 1.3.6.1.4.1.868.2.4.1.2.2.15.1.31
The number of good packets transmitted by this port that are directed to a unicast address.
OBJECT-TYPE    
  INTEGER  

smacf100PTxCollisions 1.3.6.1.4.1.868.2.4.1.2.2.15.1.32
The number of collisions experienced by this port during packet transmissions.
OBJECT-TYPE    
  INTEGER  

smacf100PTxSingleCollision 1.3.6.1.4.1.868.2.4.1.2.2.15.1.33
The number of packets successfully transmitted by this port that experienced exactly one collision.
OBJECT-TYPE    
  INTEGER  

smacf100PTxMultipleCollision 1.3.6.1.4.1.868.2.4.1.2.2.15.1.34
The number of packets successfully transmitted by this port that experienced more than one collision.
OBJECT-TYPE    
  INTEGER  

smacf100PTxDeferredTransmit 1.3.6.1.4.1.868.2.4.1.2.2.15.1.35
The number of packets transmitted by a this port for which the first transmission attempt was delayed because the medium was busy.
OBJECT-TYPE    
  INTEGER  

smacf100PTxLateCollision 1.3.6.1.4.1.868.2.4.1.2.2.15.1.36
The number of times that a collision was detected later than 512 bit-times into the transmission of a packet.
OBJECT-TYPE    
  INTEGER  

smacf100PTxExcessiveCollision 1.3.6.1.4.1.868.2.4.1.2.2.15.1.37
The number of packets that were not transmitted from this port because 16 unsucessful attempts were made to transmit the packet.
OBJECT-TYPE    
  INTEGER  

smacf100PTxFrameInDisc 1.3.6.1.4.1.868.2.4.1.2.2.15.1.38
The number of valid packets received which are discarded by the forwarding process due to lack of space on an output queue. This attribute only increments if a network device is not acting in compliance with a flow control request.
OBJECT-TYPE    
  INTEGER  

smacf100PTxPausePkts 1.3.6.1.4.1.868.2.4.1.2.2.15.1.39
The number of PAUSE frames transmitted by this port. This implies that the port is in full duplex mode and that 802.3x flow control was enabled at the completion of autonegotiation.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

smacf100PRxUndersizePkts 1.3.6.1.4.1.868.2.4.1.2.2.15.1.40
The number of good packets received by this port that are less than 64 bytes long (excluding framing bits but including the Frame Check Sequence).
OBJECT-TYPE    
  INTEGER  

smacf100PRxPausePkts 1.3.6.1.4.1.868.2.4.1.2.2.15.1.41
The number of PAUSE frames recieved by this port. The PAUSE frame must have a valid MAC Control Frame EtherType field (88- 08h), have a destination MAC address of either the MAC Control frame reseved multicast address (01:80:C2:00:00:01), be a minimum of 64 bytes long (excluding preamble but including Frame Check Sequence), and have a valid CRC. Although an 802.3 compliant MAC is only permitted to transmit PAUSE frames when in full duplex mode with flow control enabled and with the transfer of PAUSE frames determined by the result of autonegotiation, an 802.3 MAC receiver is required to count all received PAUSE frames, regardless of its half/full-duplex status. An indication that a MAC is in half-duplex mode with this counter incrementing indicates a non- compliant transmitting device on the network.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

smacf100PPkts64Octets 1.3.6.1.4.1.868.2.4.1.2.2.15.1.42
The number of packets, including error packets, that are 64 bytes long.
OBJECT-TYPE    
  INTEGER  

smacf100PPkts65to127Octets 1.3.6.1.4.1.868.2.4.1.2.2.15.1.43
The number of packets, including error packets, that are between 65 and 127 bytes long.
OBJECT-TYPE    
  INTEGER  

smacf100PPkts128to255Octets 1.3.6.1.4.1.868.2.4.1.2.2.15.1.44
The number of packets, including error packets, that are between 128 and 255 bytes long.
OBJECT-TYPE    
  INTEGER  

smacf100PPkts256to511Octets 1.3.6.1.4.1.868.2.4.1.2.2.15.1.45
The number of packets, including error packets, that are between 256 and 511 bytes long.
OBJECT-TYPE    
  INTEGER  

smacf100PPkts512to1023Octets 1.3.6.1.4.1.868.2.4.1.2.2.15.1.46
The number of packets, including error packets, that are between 512 and 1023 bytes long.
OBJECT-TYPE    
  INTEGER  

smacf100PPkts1024to1522Octets 1.3.6.1.4.1.868.2.4.1.2.2.15.1.47
The number of packets, including error packets, that are between 1024 and 1522 bytes long.
OBJECT-TYPE    
  INTEGER  

smacf100PRxOversizePkts 1.3.6.1.4.1.868.2.4.1.2.2.15.1.48
The number of good packets received by this port that are longer than 1522 bytes inclusive (excluding framing bits but including the Frame Check Sequence). Note that this counter alone will be incremented for packets in the range 1523 to 1536 bytes inclusive, whereas both this counter and the RxExcessSizeDisc counter will be incremented for packets of 1537 bytes and longer.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

smacf100PRxJabbers 1.3.6.1.4.1.868.2.4.1.2.2.15.1.49
The number of packets received by a port that are longer than 1522 bytes and have either a Frame Check Sequence error or an alignment error.
OBJECT-TYPE    
  INTEGER  

smacf100PRxAlignmentErrors 1.3.6.1.4.1.868.2.4.1.2.2.15.1.50
The number of packets received by this port that have a length (excluding framing bits but including the Frame Check Sequence) between 64 and 1522 bytes inclusive, and have a bad Frame Check Sequence with a non-integral number of bytes.
OBJECT-TYPE    
  INTEGER  

smacf100PRxFCSErrors 1.3.6.1.4.1.868.2.4.1.2.2.15.1.51
The number of packets received by this port that have a length (excluding framing bits but including the Frame Check Sequence) between 64 and 1522 bytes inclusive, and have a bad Frame Check Sequence with a integral number of bytes.
OBJECT-TYPE    
  INTEGER  

smacf100PRxGoodOctets 1.3.6.1.4.1.868.2.4.1.2.2.15.1.52
The total number of bytes in all good packets received by a port (excluding framing bits but including Frame Check Sequences).
OBJECT-TYPE    
  INTEGER  

smacf100PWrapRxGoodOctets 1.3.6.1.4.1.868.2.4.1.2.2.15.1.53
The number of times that the unsigned 32-bit smacf100PRxGoodOctets(52) MIB variable for this port has wrapped.
OBJECT-TYPE    
  INTEGER  

smacf100PRxDropPkts 1.3.6.1.4.1.868.2.4.1.2.2.15.1.54
The number of good packets received by this port that were dropped due to lack of resources (e.g. lack of input buffers) or were dropped due to a lack of resources before a determination of the validity of the packet could be made (e.g. receive FIFO overflow). The counter is only incremented if the receive error was not counted by either the RxExcessSizeDisc, the RxAlignmentErrors or the RxFCSErrors counters.)
OBJECT-TYPE    
  INTEGER  

smacf100PRxUnicastPkts 1.3.6.1.4.1.868.2.4.1.2.2.15.1.55
The number of good packets received by this port that are addressed to a unicast address.
OBJECT-TYPE    
  INTEGER  

smacf100PRxMulticastPkts 1.3.6.1.4.1.868.2.4.1.2.2.15.1.56
The number of good packets received by this port that are directed to a multicast address. This counter includes neither errored multicast packets nor valid broadcast packets.
OBJECT-TYPE    
  INTEGER  

smacf100PRxBroadcastPkts 1.3.6.1.4.1.868.2.4.1.2.2.15.1.57
The number of good packets received by this port that are directed to the broadcast address. This counter includes neither errored broadcast packets nor valid multicast packets.
OBJECT-TYPE    
  INTEGER  

smacf100PRxSAChanges 1.3.6.1.4.1.868.2.4.1.2.2.15.1.58
The number of times the Source Ethernet Address of good receive packets has changed from the previous value. A count greater than one generally indicates that the port is connected to a repeater-based network.
OBJECT-TYPE    
  INTEGER  

smacf100PRxFragments 1.3.6.1.4.1.868.2.4.1.2.2.15.1.59
The number of packets received by a port that are shorter than 64 bytes (excluding framing bits) and have either an Frame Check Sequence error or an alignment error.
OBJECT-TYPE    
  INTEGER  

smacf100PRxExcessSizeDisc 1.3.6.1.4.1.868.2.4.1.2.2.15.1.60
The number of good packets received by this port that are longer than 1536 bytes (excluding framing bits but including Frame Check Sequences) and were discarded due to excessive length. Note that the RxOversizePkts counter alone is incremented for packets in the range 1523-1536 bytes inclusive, whereas both RxExcessSizeDisc and RxOversizePkts are incremented for packets of 1537 bytes and longer.
OBJECT-TYPE    
  INTEGER  

smacf100PRxSymbolError 1.3.6.1.4.1.868.2.4.1.2.2.15.1.61
The total number of times this port received a packet which had a valid length, but contained at least one invalid symbol. The counter only increments once per carrier event, and does not increment if a collision is detected during the carrier event.
OBJECT-TYPE    
  INTEGER  

smacf100PQosPriority 1.3.6.1.4.1.868.2.4.1.2.2.15.1.62
When this variable is set to 'high(1)', this port becomes a high-priority port. This means that all packets received on this port for transission on other ports and all packets received on other ports for transmission on this port are placed in the high-priority queues. When the variable is set to 'default(2)', the low priority queue is used unless other conditions (i.e. an 802.1p tag or a high-priority setting for another port) prompt the use of the high priority queue.
OBJECT-TYPE    
  INTEGER  

smacf100PQosPause 1.3.6.1.4.1.868.2.4.1.2.2.15.1.63
When the global variable smacf100QosEnable(7) is set to 'enabled(1)', then the port-specific variable smacf100PQosPause(63) controls whether or not the port supports half-duplex back pressure and full-duplex flow control. Otherwise, only dropping of frames is supported for the port.
OBJECT-TYPE    
  INTEGER  

smacf100PAdvPause 1.3.6.1.4.1.868.2.4.1.2.2.15.1.64
Enable/disable control for this advertised autonegotiation mode. When Pause capability is autonegotiated (at the Physical level), the MAC layer may then send Pause packets to pace data coming across the link. smacf100PAutoNegot(12) must be set to 'enabled(1)'. The results of this autonegotiation are ignored if smacf100QosEnable(7) is set to 'enabled(1)' and smacf100PQosPause(63) is set to 'disabled(2)'. In this case, no 'Pause' capability is supported.
OBJECT-TYPE    
  INTEGER  

smacf100PCacheClean 1.3.6.1.4.1.868.2.4.1.2.2.15.1.65
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cpsld100Table 1.3.6.1.4.1.868.2.4.1.2.2.16
Sparse table containing one entry for each CPSLD100 in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Cpsld100Entry

cpsld100Entry 1.3.6.1.4.1.868.2.4.1.2.2.16.1
Status and configuration entries for a single CPSLD100
OBJECT-TYPE    
  Cpsld100Entry  

cpsld100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.16.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

cpsld100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.16.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

cpsld100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.16.1.3
The serial number of this device
OBJECT-TYPE    
  INTEGER  

cpsld100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.16.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cpsld100Ps1Power 1.3.6.1.4.1.868.2.4.1.2.2.16.1.5
Power status, first power supply slot. Value is on(1) when the supply is capable of supplying power.
OBJECT-TYPE    
  INTEGER on(1), off(2), notInstalled(3)  

cpsld100Ps1InUse 1.3.6.1.4.1.868.2.4.1.2.2.16.1.6
Power status, first power supply slot. Value is yes(1) when the power is selected to supply power to the cabinet.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notInstalled(3)  

cpsld100Ps2Power 1.3.6.1.4.1.868.2.4.1.2.2.16.1.7
Power status, second power supply slot. Value is on(1) when the supply is capable of supplying power.
OBJECT-TYPE    
  INTEGER on(1), off(2), notInstalled(3)  

cpsld100Ps2InUse 1.3.6.1.4.1.868.2.4.1.2.2.16.1.8
Power status, second power supply slot. Value is yes(1) when the power is selected to supply power to the cabinet.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notInstalled(3)  

cdftf100Table 1.3.6.1.4.1.868.2.4.1.2.2.17
Sparse table containing one entry for each CDFTF100 Dual telco Media Converter in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Cdftf100Entry

cdftf100Entry 1.3.6.1.4.1.868.2.4.1.2.2.17.1
Status and configuration entries for a single CDFTF100
OBJECT-TYPE    
  Cdftf100Entry  

cdftf100SubDeviceIndex 1.3.6.1.4.1.868.2.4.1.2.2.17.1.1
Generally, individual devices in this MIB are distinguished by BiaIndex and SlotIndex. This device differs from many in that it contains multiple subdevices (in this case, switch ports). The number of subdevices varies with the manufactured configuration. Subdevices within devices are indexed by BiaIndex, SlotIndex, and SubDeviceIndex. When the subdevice column is read from the table, the value '1' is always returned.
OBJECT-TYPE    
  INTEGER  

cdftf100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.17.1.2
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

cdftf100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.17.1.3
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

cdftf100Groups 1.3.6.1.4.1.868.2.4.1.2.2.17.1.4
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CDFTF100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

cdftf100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.17.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cdftf100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.17.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  

cdftf100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.17.1.7
The marketing revision of the device
OBJECT-TYPE    
  INTEGER  

cdftf100TPLinkTbl 1.3.6.1.4.1.868.2.4.1.2.2.17.1.8
This table contains the link status of each twisted pair port in the CDFTF100. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

cdftf100FiberLinkTbl 1.3.6.1.4.1.868.2.4.1.2.2.17.1.9
This table contains the link status of each fiber port in the CDFTF100. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

cdftf100TPActivityTbl 1.3.6.1.4.1.868.2.4.1.2.2.17.1.10
Netowrk traffic indicator for the copper port(s) on this device. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cdftf100FiberActivityTbl 1.3.6.1.4.1.868.2.4.1.2.2.17.1.11
Netowrk traffic indicator for the fiber port(s) on this device. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cdftf100ConnectorTbl 1.3.6.1.4.1.868.2.4.1.2.2.17.1.12
This table contains the link status of each port of this device. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

cdftf100FirmwareRevision 1.3.6.1.4.1.868.2.4.1.2.2.17.1.13
The style of connectors built into each port of this device.
OBJECT-TYPE    
  CpsConnector  

cdftf100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.17.1.14
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cpsvt100Table 1.3.6.1.4.1.868.2.4.1.2.2.18
Sparse table containing one entry for each CPSVT100 in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Cpsvt100Entry

cpsvt100Entry 1.3.6.1.4.1.868.2.4.1.2.2.18.1
Status and configuration entries for a single CPSVT100
OBJECT-TYPE    
  Cpsvt100Entry  

cpsvt100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.18.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

cpsvt100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.18.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

cpsvt100Groups 1.3.6.1.4.1.868.2.4.1.2.2.18.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CPSVT100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

cpsvt100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.18.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cpsvt100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.18.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), inactive(3)  

cpsvt100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.18.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  



cpsvt100Fault 1.3.6.1.4.1.868.2.4.1.2.2.18.1.9
Value is yes(1) when either CopperLink or FiberLink has value linkDown(2)
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsvt100ConnA 1.3.6.1.4.1.868.2.4.1.2.2.18.1.10
The style of Fiber connector built into this device
OBJECT-TYPE    
  CpsConnector  

cpsvt100ConnB 1.3.6.1.4.1.868.2.4.1.2.2.18.1.11
The style of Copper connector built into this device
OBJECT-TYPE    
  CpsConnector  

cpsvt100TermTiming 1.3.6.1.4.1.868.2.4.1.2.2.18.1.12
Local Terminal Timing setting. Terminal timing is a signal sent from a DCE to a DTE to control the rate of data the DTE sends to the DCE. Since this signal cannot be sent across the fiber after media converters are introduced, the converter must generate this signal and supply it to the DTE. The converter gets the setting from a thumbwheel. For converters attached to DTEs, the thumbwheel setting influences the transmit data rate. If the Terminal Timing setting is RXC, the DTE derives its transmit clock from the receive clock supplied by the DCE. For converters attached to DCEs, the thumbwheel setting has no effect. If two DTEs are connected via media converters, the thumbwheel settings must not be RXC.
OBJECT-TYPE    
  INTEGER rxc(1), kbps56(2), kbps64(3), kbps112(4), kbps128(5), kbps256(6), kbps384(7), kbps512(8), kbps768(9), kbps1024(10), kbps1554(11), kbps2048(12), kbps3072(13), kbps4096(14), kbps6144(15), asynchronous(16)  

cpsvt100LoopBack 1.3.6.1.4.1.868.2.4.1.2.2.18.1.13
Remote fiber and copper loopback setting. Loopback is a testing aid available on several different products. When Loopback is enabled on an interface, all data that is sent to the interface is reflected back to the sender, and the actual condition (or even existence) of the equipment on the opposite interface is ignored.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cpsvt100CableMode 1.3.6.1.4.1.868.2.4.1.2.2.18.1.14
A description of the type of cable that is attached to the Copper interface of the local device.
OBJECT-TYPE    
  INTEGER notValid(1), rs-530A(2), rs-530(3), x-21(4), v-35(5), rs-449(6), rs-232(7), disconnected(8)  

cpsvt100DCE 1.3.6.1.4.1.868.2.4.1.2.2.18.1.15
An indication of whether this device is attached to a DCE (a computer) or a DTE (a terminal). Like cpsvt100CableMode(14), this status is derived from the type of cable that is attached to the copper interface.
OBJECT-TYPE    
  INTEGER dce(1), dte(2)  

cpsvt100InvertTX 1.3.6.1.4.1.868.2.4.1.2.2.18.1.16
Local transmit clock usage. Some types of high-speed serial equipment read the data signal on the rising edge of the clock, and others on the falling edge of the clock. The CPSVT100-xxx High Speed Serial converter is compatible with both types of equipment. The expectations of the equipment attached to the copper interface can be matched via jumper settings on the converter. The cpsvt100InvertTX(16) and cpsvt100InvertRX(17) status variables indicate the status of these jumpers. Most high-speed serial equipment uses the rising edge of the clock.
OBJECT-TYPE    
  INTEGER rising(1), falling(2)  

cpsvt100InvertRX 1.3.6.1.4.1.868.2.4.1.2.2.18.1.17
Local receive clock usage. Some types of high-speed serial equipment read the data signal on the rising edge of the clock, and others on the falling edge of the clock. The CPSVT100-xxx High Speed Serial converter is compatible with both types of equipment. The expectations of the equipment attached to the copper interface can be matched via jumper settings on the converter. The cpsvt100InvertTX(16) and cpsvt100InvertRX(17) status variables indicate the status of these jumpers. Most high-speed serial equipment uses the rising edge of the clock.
OBJECT-TYPE    
  INTEGER rising(1), falling(2)  

cpsvt100ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.18.1.18
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

cpsvt100FirmwareRev 1.3.6.1.4.1.868.2.4.1.2.2.18.1.19
Local firmware revision.
OBJECT-TYPE    
  INTEGER  

cpsvt100RmtDetected 1.3.6.1.4.1.868.2.4.1.2.2.18.1.20
Has the value yes(1) if management communcations have been established with a remote media converter.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsvt100RmtTermTiming 1.3.6.1.4.1.868.2.4.1.2.2.18.1.21
Local Terminal Timing setting of the remotely managed CPSVTxxx. Terminal timing is a signal sent from a DCE to a DTE to control the rate of data the DTE sends to the DCE. Since this signal cannot be sent across the fiber after media converters are introduced, the converter must generate this signal and supply it to the DTE. The converter gets the setting from a thumbwheel. For converters attached to DTEs, the thumbwheel setting influences the transmit data rate. If the Terminal Timing setting is RXC, the DTE derives its transmit clock from the receive clock supplied by the DCE. For converters attached to DCEs, the thumbwheel setting has no effect. If two DTEs are connected via media converters, the thumbwheel settings must not be RXC.
OBJECT-TYPE    
  INTEGER rxc(1), kbps56(2), kbps64(3), kbps112(4), kbps128(5), kbps256(6), kbps384(7), kbps512(8), kbps768(9), kbps1024(10), kbps1554(11), kbps2048(12), kbps3072(13), kbps4096(14), kbps6144(15), asynchronous(16)  

cpsvt100RmtLoopBack 1.3.6.1.4.1.868.2.4.1.2.2.18.1.22
Remote fiber and copper loopback setting. Loopback is a testing aid available on several different products. When Loopback is enabled on an interface, all data that is sent to the interface is reflected back to the sender, and the actual condition (or even existence) of the equipment on the opposite interface is ignored. This variable is identical to cpsvt100LoopBack, except that it is for the remotely managed cpsvt100.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cpsvt100RmtCableMode 1.3.6.1.4.1.868.2.4.1.2.2.18.1.23
A description of the type of cable that is attached to the Copper interface of the local device.
OBJECT-TYPE    
  INTEGER  

cpsvt100RmtDCE 1.3.6.1.4.1.868.2.4.1.2.2.18.1.24
An indication of whether this device is attached to a DCE (a computer) or a DTE (a terminal). Like cpsvt100CableMode(14), this status is derived from the type of cable that is attached to the copper interface.
OBJECT-TYPE    
  INTEGER  

cpsvt100RmtInvertTX 1.3.6.1.4.1.868.2.4.1.2.2.18.1.25
Local transmit clock usage. Some types of high-speed serial equipment read the data signal on the rising edge of the clock, and others on the falling edge of the clock. The CPSVT100-xxx High Speed Serial converter is compatible with both types of equipment. The expectations of the equipment attached to the copper interface can be matched via jumper settings on the converter. The cpsvt100InvertTX(16) and cpsvt100InvertRX(17) status variables indicate the status of these jumpers. Most high-speed serial equipment uses the rising edge of the clock.
OBJECT-TYPE    
  INTEGER  

cpsvt100RmtInvertRX 1.3.6.1.4.1.868.2.4.1.2.2.18.1.26
Local receive clock usage. Some types of high-speed serial equipment read the data signal on the rising edge of the clock, and others on the falling edge of the clock. The CPSVT100-xxx High Speed Serial converter is compatible with both types of equipment. The expectations of the equipment attached to the copper interface can be matched via jumper settings on the converter. The cpsvt100InvertTX(16) and cpsvt100InvertRX(17) status variables indicate the status of these jumpers. Most high-speed serial equipment uses the rising edge of the clock.
OBJECT-TYPE    
  INTEGER  

cpsvt100RmtConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.18.1.27
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

cpsvt100RmtFirmwareRev 1.3.6.1.4.1.868.2.4.1.2.2.18.1.28
Local firmware revision.
OBJECT-TYPE    
  INTEGER  



cpsvt100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.18.1.31
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cemtf100Table 1.3.6.1.4.1.868.2.4.1.2.2.19
Sparse table containing one entry for each CEMTF100 in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Cemtf100Entry

cemtf100Entry 1.3.6.1.4.1.868.2.4.1.2.2.19.1
Status and configuration entries for a single CEMTF100
OBJECT-TYPE    
  Cemtf100Entry  

cemtf100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.19.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

cemtf100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.19.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

cemtf100Groups 1.3.6.1.4.1.868.2.4.1.2.2.19.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CEMTF100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

cemtf100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.19.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cemtf100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.19.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cemtf100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.19.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  


cemtf100OffHook 1.3.6.1.4.1.868.2.4.1.2.2.19.1.8
Status of Twisted Pair Link for this device
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cemtf100Fault 1.3.6.1.4.1.868.2.4.1.2.2.19.1.9
Value is yes(1) when either OffHook or FiberLink has value of down
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cemtf100ConnA 1.3.6.1.4.1.868.2.4.1.2.2.19.1.10
The style of Fiber connector built into this device
OBJECT-TYPE    
  CpsConnector  

cemtf100ConnB 1.3.6.1.4.1.868.2.4.1.2.2.19.1.11
The style of Copper connector built into this device
OBJECT-TYPE    
  CpsConnector  

cemtf100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.19.1.12
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

captf100Table 1.3.6.1.4.1.868.2.4.1.2.2.20
Sparse table containing one entry for each CAPTF100 in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Captf100Entry

captf100Entry 1.3.6.1.4.1.868.2.4.1.2.2.20.1
Status and configuration entries for a single CAPTF100
OBJECT-TYPE    
  Captf100Entry  

captf100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.20.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

captf100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.20.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

captf100Groups 1.3.6.1.4.1.868.2.4.1.2.2.20.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CAPTF100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

captf100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.20.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

captf100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.20.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

captf100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.20.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  


captf100InUse 1.3.6.1.4.1.868.2.4.1.2.2.20.1.8
Status of Twisted Pair Link for this device
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

captf100Fault 1.3.6.1.4.1.868.2.4.1.2.2.20.1.9
Value is yes(1) when either OffHook or FiberLink has value of down
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

captf100ConnA 1.3.6.1.4.1.868.2.4.1.2.2.20.1.10
The style of Fiber connector built into this device
OBJECT-TYPE    
  CpsConnector  

captf100ConnB 1.3.6.1.4.1.868.2.4.1.2.2.20.1.11
The style of Copper connector built into this device
OBJECT-TYPE    
  CpsConnector  

captf100FirmwareRev 1.3.6.1.4.1.868.2.4.1.2.2.20.1.12
The firmware revision level for this device.
OBJECT-TYPE    
  INTEGER  

captf100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.20.1.13
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

captf100Emulates 1.3.6.1.4.1.868.2.4.1.2.2.20.1.14
This read-only variable indicates the emulation type and configuration of the device. CAPTF100 devices exist in two varieties, the CAPTF10033xx-100, the copper port of which emulates a telephone, and the CAPTF10033xx-110, the copper port of which emulates the Central Office (CO) (i.e. a wall jack that one would plug a telephone into). The Standard CAPTF100 configuration is employed when a fiber extension between a wall jack and a distant telephone is desired. The CAPTF100 whose copper port was plugged into the wall jack must be of the variety that emulates a telephone. The value of the captf100Emulates(14) variable of such a device will be phone(1). The CAPTF100 whose copper port was plugged into the telephone must be of the variety that emulates the CO, and that device must be jumpered for 'Standard' operation. The value of its captf100Emulates(14) variable would be coStandard(2). Alternatively, CAPTF100 converters can be used to provide a point-to-point fiber link between two telephones. This is known as the Automatic Ring-Down configuration. When one telephone goes off-hook, the other rings. When both are off hook, voice communication is possible. In this configuration, both CAPTF100 devices must be of the variety that emulates the CO, and both devices must be jumpered for 'Automatic Ring-Down' operation. The value of their captf100Emulates(14) variables would be coAutoRingDown(3).
OBJECT-TYPE    
  INTEGER phone(1), coStandard(2), coAutoRingDown(3)  

cfetf205Table 1.3.6.1.4.1.868.2.4.1.2.2.21
Sparse table containing one entry for each CFTEF205 100Mbps Twisted-Pair to Fiber Ethernet Media Converter in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Cfetf205Entry

cfetf205Entry 1.3.6.1.4.1.868.2.4.1.2.2.21.1
Status and configuration entries for a single CFETF205
OBJECT-TYPE    
  Cfetf205Entry  

cfetf205BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.21.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

cfetf205SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.21.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

cfetf205Groups 1.3.6.1.4.1.868.2.4.1.2.2.21.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CFETF205' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

cfetf205MRevision 1.3.6.1.4.1.868.2.4.1.2.2.21.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cfetf205CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.21.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cfetf205SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.21.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  

cfetf205ConnA 1.3.6.1.4.1.868.2.4.1.2.2.21.1.7
The style of Fiber connector built into this device
OBJECT-TYPE    
  CpsConnector  

cfetf205ConnB 1.3.6.1.4.1.868.2.4.1.2.2.21.1.8
The style of Copper connector built into this device
OBJECT-TYPE    
  CpsConnector  



cfetf205Fault 1.3.6.1.4.1.868.2.4.1.2.2.21.1.11
Value is yes(1) when either TPLink or FiberLink has value linkDown(2)
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cfetf205FastLinkPulse 1.3.6.1.4.1.868.2.4.1.2.2.21.1.12
When set to autonegotiate(1), converter sends Fast Link Pulses on its twisted pair port, thereby participating in autonegotiation of duplex between the converter's twisted pair port and that of the connected station. If that station supports Full- Duplex (FDX) operation, FDX will be used. If not, the twisted pair will operate in Half-Duplex (HDX) mode. When set to hdx100Btx(2), the converter instead sends 100Mbps idles (rather than Fast Link Pulses) on its twisted pair port (i.e. it declines to negotiate), which forces the twisted pair to operate in HDX mode regardless of the capabilities of the connected station. When operating in HDX mode, the twisted pair can support traffic in only one direction at a time. In FDX mode, traffic can pass in both directions simultaneously, thus theoretically doubling network performance.
OBJECT-TYPE    
  INTEGER autonegotiate(1), hdx100Btx(2)  

cfetf205Enabled 1.3.6.1.4.1.868.2.4.1.2.2.21.1.13
When this configuration item is set to no(2), the device passes no network traffic.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cfetf205Pause 1.3.6.1.4.1.868.2.4.1.2.2.21.1.14
The Pause feature allows Ethernet MACs that support it to send data pacing 'Pause' messages to each other. Support for Pause is negotiated at the physical level and passed up to the MAC. While the MAC's Pause messages themselves can pass over the fiber link that this pair of media converters introduces, the TP physical layer negotiations to enable Pause can not. Therefore, if both end station MACs support Pause and wish to use it, the Pause negotiation must be re-generated by the media converters on both ends. By setting this configuration option to enabled(1), you are indicating to the local twisted pair station that the twisted pair station on the other side of the other media converter supports Pause and wishes to use it. This variable must be set consistently on both of the paired media converters.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cfetf205LinkPassThrough 1.3.6.1.4.1.868.2.4.1.2.2.21.1.15
Enable/Disable for Link Pass Through, a feature that causes loss of link on one side of a media converter to be passed through to the other side, so that upstream equipment can see the fault condition.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cfetf205AutoCross 1.3.6.1.4.1.868.2.4.1.2.2.21.1.16
Enable/Disable for automatic copper TX/RX pair correction. When disabled, the port operates in MDI mode.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cfetf205TPActivity 1.3.6.1.4.1.868.2.4.1.2.2.21.1.17
Network traffic indicator for Copper side of this device
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

cfetf205FiberActivity 1.3.6.1.4.1.868.2.4.1.2.2.21.1.18
Network traffic indicator for Fiber side of this device
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

cfetf205ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.21.1.19
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

cfetf205FarEndFault 1.3.6.1.4.1.868.2.4.1.2.2.21.1.20
Far End Fault configuration of this device. Far End Fault causes the fiber transmitter to generate a Far End Fault pattern upon the loss of a receiver signal detect. When the receiver detects signal again, the transmitter stops transmitting the Far End Fault pattern.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

cfetf205CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.21.1.21
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cbftf150Table 1.3.6.1.4.1.868.2.4.1.2.2.22
Sparse table containing one entry for each CBFTF150 switch in the stack. Indexed by sub-device index, cabinet serial number, and slot. Note that some columns of this table support multiple subdevices, and some do not. For example, there is exactly one SerialNumber for each CBFTF150. No subdevices exist, so the placeholder value 1 is used as the subdevice index. However, a CBFTF150 has multiple switch ports, which are indexed as different subdevices, starting with 1. Columns with subdevices have names ending in 'Tbl'
OBJECT-TYPE    
  SEQUENCE OF  
    Cbftf150Entry

cbftf150Entry 1.3.6.1.4.1.868.2.4.1.2.2.22.1
Status and configuration entries for a single CBFTF150
OBJECT-TYPE    
  Cbftf150Entry  

cbftf150SubDeviceIndex 1.3.6.1.4.1.868.2.4.1.2.2.22.1.1
Generally, individual devices in this MIB are distinguished by BiaIndex and SlotIndex. This device differs from many in that it contains multiple subdevices (in this case, switch ports). The number of subdevices varies with the manufactured configuration. Subdevices within devices are indexed by BiaIndex, SlotIndex, and SubDeviceIndex. When the subdevice column is read from the table, the value '1' is always returned.
OBJECT-TYPE    
  INTEGER  

cbftf150BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.22.1.2
The serial number (BIA) of the cabinet in which the device is installed. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER  

cbftf150SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.22.1.3
The slot in which the device is installed. Power Supplies occupy special slots numbered 125 and higher. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER  

cbftf150Groups 1.3.6.1.4.1.868.2.4.1.2.2.22.1.4
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'cbftf150' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]' There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  DisplayString  

cbftf150MRevision 1.3.6.1.4.1.868.2.4.1.2.2.22.1.5
The marketing revision of this device. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER  

cbftf150CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.22.1.6
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cbftf150SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.22.1.7
The serial number of this device. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER  

cbftf150ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.22.1.8
This device may have a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

cbftf150FirmwareRevision 1.3.6.1.4.1.868.2.4.1.2.2.22.1.9
The firmware revision level for this device. There are no subdevices for this value, so the placeholder value 1 is always used for that index.
OBJECT-TYPE    
  INTEGER  

cbftf150FormFactor 1.3.6.1.4.1.868.2.4.1.2.2.22.1.10
A code corresponding to a physical configuration of the product. This code indicates the number of slots occupied and the number of physical connectors present. In the labels for the values above, s indicates the number of slots occupied, W is a count of Wide port positions (which can built as almost any type of connector), and N is a count of narrow port positions (which are typically twisted pair ports). The lowercase letter at the end differentiates different form factors that would otherwise have identical descriptions under this limited scheme.
OBJECT-TYPE    
  INTEGER s1W2a(1), s1W1N2a(2), s1W1N1a(3), s2W2N4a(4), s2W1N5a(5)  

cbftf150AutoNegotTbl 1.3.6.1.4.1.868.2.4.1.2.2.22.1.11
Enables or disables autonegtiation of link speed and duplex for twisted pair ports. Not supported on Fiber ports. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

cbftf150FullDuplexTbl 1.3.6.1.4.1.868.2.4.1.2.2.22.1.12
In most cases this is a configuration setting that controls the duplex mode; fullDuplex is full duplex and halfDuplex is half duplex. On twisted pair ports with autonegotiation enabled, this is a status indication showing the duplex value decided upon during the negotiation. When link is down, autonegotiation has not been completed yet, and the duplex setting is therefore unknown and the value is negotiating(3). There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER fullDuplex(1), halfDuplex(2), negotiating(3)  

cbftf150100MbpsTbl 1.3.6.1.4.1.868.2.4.1.2.2.22.1.13
In most cases this is a configuration setting that controls the link speed. On twisted pair ports with autonegotiation enabled, this is a status indication showing the link speed decided upon during negotiation. When link is down, autonegotiation has not been completed yet, and the link speed is therefore unknown and is negotiating(3). This variable is an indicator only for fiber ports; all fiber ports report mbps100(1) at all times. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER mbps100(1), mbps10(2), negotiating(3)  

cbftf150CrossTbl 1.3.6.1.4.1.868.2.4.1.2.2.22.1.14
Configuration setting for copper TX/RX pair correction. A setting of auto(1) causes the port to automatically correct TX/RX pairs if necessary. If autonegotiation is disabled on the port, the auto(1) setting is not supported. A setting of mdi(2) causes the TX/RX pairs to be passed straight through with no correction. A setting of mdix(3) causes the TX/RX pairs to be swapped. This setting is supprted for copper ports only; a read-only value of notSupported(4) is returned for fiber ports. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER auto(1), mdi(2), mdix(3), notSupported(4)  

cbftf150FarEndFaultTbl 1.3.6.1.4.1.868.2.4.1.2.2.22.1.15
When Far End Fault is set to enabled(1), a loss of link on receive will cause the transmitter to shut down, in order to inform the device at the far end of the link that a fault has occurred. Far End Fault is only supported on fiber ports. A read-only value of notSupported(3) is returned for copper ports. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

cbftf150ConnectorTbl 1.3.6.1.4.1.868.2.4.1.2.2.22.1.16
The style of connectors built into each port of this device. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  CpsConnector  

cbftf150LinkTbl 1.3.6.1.4.1.868.2.4.1.2.2.22.1.17
This table contains the link status of each port in the switch. There are multiple subdevices in this table, numbering one entry per port.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

cbftf150PortCount 1.3.6.1.4.1.868.2.4.1.2.2.22.1.18
A count of the switch ports in this device. i.e. the maximum subdevice index supported by this switch.
OBJECT-TYPE    
  INTEGER  

cbftf150CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.22.1.19
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cgfeb100Table 1.3.6.1.4.1.868.2.4.1.2.2.23
Sparse table containing one entry for each CGFEB100 10/100/1000 Ethernet to Fiber converter in the stack. Indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Cgfeb100Entry

cgfeb100Entry 1.3.6.1.4.1.868.2.4.1.2.2.23.1
Status and configuration entries for a single CGFEB100
OBJECT-TYPE    
  Cgfeb100Entry  

cgfeb100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.23.1.1
The serial number (BIA) of the cabinet in which the device is installed.
OBJECT-TYPE    
  INTEGER  

cgfeb100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.23.1.2
The slot in which the device is installed. Power Supplies occupy special slots numbered 125 and higher.
OBJECT-TYPE    
  INTEGER  

cgfeb100Groups 1.3.6.1.4.1.868.2.4.1.2.2.23.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'cgfeb100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'.
OBJECT-TYPE    
  DisplayString  

cgfeb100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.23.1.4
The marketing revision of this device.
OBJECT-TYPE    
  INTEGER  

cgfeb100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.23.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cgfeb100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.23.1.6
The serial number of this device.
OBJECT-TYPE    
  INTEGER  

cgfeb100ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.23.1.7
This device may have a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

cgfeb100FirmwareRevision 1.3.6.1.4.1.868.2.4.1.2.2.23.1.8
The firmware revision level for this device.
OBJECT-TYPE    
  INTEGER  

cgfeb100SelfTestFailed 1.3.6.1.4.1.868.2.4.1.2.2.23.1.9
This variable indicates the status of the pass/fail power on test. If the power on test fails, normal operation of this device is probably not possible.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cgfeb100MonitorType 1.3.6.1.4.1.868.2.4.1.2.2.23.1.10
Some versions of this device support the monitoring of network traffic passing through the converter's fiber interface via a dedicated monitoring port to which a capture device can be attached. There are two different versions of the monitoring capability. One has a fiber connector, and the other has a twisted pair connector. Both versions monitor the fiber port. If this variable has the value fiber(1) or twistedPair(2), this means that a monitoring port is present and that port has the specified type of interface. In this case, the device occupies two slots. If the value is notInstalled(3), there is no monitoring capability and the device occupies one slot. See also cgfeb100MonitorTap(56).
OBJECT-TYPE    
  INTEGER fiber(1), twistedPair(2), notInstalled(3)  

cgfeb100LinkPassThrough 1.3.6.1.4.1.868.2.4.1.2.2.23.1.11
This configuration item allows Link Pass Through to be enabled(1) or disabled(2). Link Passthrough causes loss of link on one side of a media converter to be passed through to the other side, so that upstream equipment can see fault conditions that would otherwise be hidden by the media converters. On some models, the Link Passthrough logic views receipt of a Far End Fault error pattern as being equivalent to loss of link. The net effect of this is that when either fiber is disconnected, link is dropped on the other side of the converter. Normally, only the disconnection of the Receive fiber would cause this reaction.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

cgfeb100QosEnabled 1.3.6.1.4.1.868.2.4.1.2.2.23.1.12
This variable allows Quality of Service functions to be enabled or disabled. This includes the processing of 802.1p tags (See cgfeb100QosHPThreshold(13), cgfeb100QosLqWeight(14), and smacf100QosHqWeight(15)), and half-duplex back pressure and full-duplex flow control. (See cgfeb100TpQosPause(39) and cgfeb100FiberQosPause(52)).
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

cgfeb100QosHPThreshold 1.3.6.1.4.1.868.2.4.1.2.2.23.1.13
When an incoming 802.1p priority tag value is greater than or equal to this value (from 0 to 7), the incoming packet will be classified as high-priority. Ignored when cgfeb100QosEnable(13) is set to 'disabled(2)'.
OBJECT-TYPE    
  INTEGER  

cgfeb100QosLqWeight 1.3.6.1.4.1.868.2.4.1.2.2.23.1.14
A value between 1 and 15 indicating the number of packets that should be processed from the low-priority queue before attention is turned to the high-priority queue. Ignored when cgfeb100QosEnable(13) is set to 'disabled(2)'.
OBJECT-TYPE    
  INTEGER  

cgfeb100QosHqWeight 1.3.6.1.4.1.868.2.4.1.2.2.23.1.15
A value between 1 and 15 indicating the number of packets that should be processed from the high-priority queue before attention is turned to the low-priority queue. Ignored when cgfeb100QosEnable(13) is set to 'disabled(2)'.
OBJECT-TYPE    
  INTEGER  

cgfeb100ConnA 1.3.6.1.4.1.868.2.4.1.2.2.23.1.16
The style of copper connector built into this device.
OBJECT-TYPE    
  CpsConnector  


cgfeb100TPSpeedCfg 1.3.6.1.4.1.868.2.4.1.2.2.23.1.18
The desired speed of the Twisted Pair interface. This speed can be set to 10Mbps(1) or 100Mbps(2). Operation at 1000Mbps requires autonegotiation. When cgfeb100TpAutonegot(24) has the value enabled(1) or cgfeb100ConfigMode(7) has the value hardware(2), this variable has the read-only value auto(3).
OBJECT-TYPE    
  INTEGER mbps10(1), mbps100(2), auto(3)  

cgfeb100TPSpeedStat 1.3.6.1.4.1.868.2.4.1.2.2.23.1.19
The actual speed of the Twisted Pair interface: 10Mbps(1), 100Mbps(2), or 1000Mbps(3). If cgfeb100TpAutonegot(24) has the value enabled(1) and cgfeb100TpLink(17) has the value down(2), this variable has the value notApplicable(4).
OBJECT-TYPE    
  INTEGER mbps10(1), mbps100(2), mbps1000(3), notApplicable(4)  

cgfeb100TPFullDuplexCfg 1.3.6.1.4.1.868.2.4.1.2.2.23.1.20
The desired duplex setting of the Twisted Pair interface. This can be set to fdx(1) (full duplex) or hdx(2) (half duplex). When cgfeb100TpAutonegot(24) has the value enabled(1) or cgfeb100ConfigMode(7) has the value hardware(2), this variable has the read-only value auto(3).
OBJECT-TYPE    
  INTEGER fdx(1), hdx(2), auto(3)  

cgfeb100TPFullDuplexStat 1.3.6.1.4.1.868.2.4.1.2.2.23.1.21
The actual duplex behavior of the Twisted Pair interface. If cgfeb100TpAutonegot(24) has the value enabled(1) and cgfeb100TpLink(17) has the value down(2), this variable has the value notApplicable(4).
OBJECT-TYPE    
  INTEGER fdx(1), hdx(2), notApplicable(3)  

cgfeb100TPCrossCfg 1.3.6.1.4.1.868.2.4.1.2.2.23.1.22
The desired TX/RX Pair orientation of the Twisted Pair interface. This can be set to mdi(1) (straight through), mdix(2) (crossed over), or auto(3). When cgfeb100ConfigMode(7) has the value hardware(2), this variable has the read-only value notApplicable(4).
OBJECT-TYPE    
  INTEGER mdi(1), mdix(2), auto(3), notApplicable(4)  

cgfeb100TPCrossStat 1.3.6.1.4.1.868.2.4.1.2.2.23.1.23
The actual TX/RX Pair orientation of the Twisted Pair interface, usually mdi(1) (straight through) or mdix(2) (crossed over). When the device does not know the pair orientation, this variable has the value auto(3). Depending on the version of the device, it may not be able to report the pair orientation when it is decided automatically. The device will never have an orientation to report when If cgfeb100TpCrossConfig(22) has the value auto(3) and cgfeb100TpLink(17) has the value down(2).
OBJECT-TYPE    
  INTEGER mdi(1), mdix(2), auto(3)  

cgfeb100TPAutoNegot 1.3.6.1.4.1.868.2.4.1.2.2.23.1.24
Enables or disables autonegtiation of link speed and duplex for twisted pair ports. Not supported on Fiber ports.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

cgfeb100TPAdv10HDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.25
Enable/disable control for these advertised autonegotiation modes. If autonegotiation is disabled (because cgfeb100TpAutonegot(24) has the value disabled(2) or cgfeb100ConfigMode(7) has the value hardware(2) and the Autonegotiation hardware switch is disabled), then these variables have no meaning and return read-only value notApplicable(3). If the value cannot be changed (because cgfeb100ConfigMode(7) has the value hardware(2)) and Autonegotiation is enabled, these variables return the read- only values enabledRO(4) or disabledRO(5).
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3), enabledRO(4), disabledRO(5)  

cgfeb100TPAdv10FDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.26
Enable/disable control for these advertised autonegotiation modes. If autonegotiation is disabled (because cgfeb100TpAutonegot(24) has the value disabled(2) or cgfeb100ConfigMode(7) has the value hardware(2) and the Autonegotiation hardware switch is disabled), then these variables have no meaning and return read-only value notApplicable(3). If the value cannot be changed (because cgfeb100ConfigMode(7) has the value hardware(2)) and Autonegotiation is enabled, these variables return the read- only values enabledRO(4) or disabledRO(5).
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3), enabledRO(4), disabledRO(5)  

cgfeb100TPAdv100HDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.27
Enable/disable control for these advertised autonegotiation modes. If autonegotiation is disabled (because cgfeb100TpAutonegot(24) has the value disabled(2) or cgfeb100ConfigMode(7) has the value hardware(2) and the Autonegotiation hardware switch is disabled), then these variables have no meaning and return read-only value notApplicable(3). If the value cannot be changed (because cgfeb100ConfigMode(7) has the value hardware(2)) and Autonegotiation is enabled, these variables return the read- only values enabledRO(4) or disabledRO(5).
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3), enabledRO(4), disabledRO(5)  

cgfeb100TPAdv100FDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.28
Enable/disable control for these advertised autonegotiation modes. If autonegotiation is disabled (because cgfeb100TpAutonegot(24) has the value disabled(2) or cgfeb100ConfigMode(7) has the value hardware(2) and the Autonegotiation hardware switch is disabled), then these variables have no meaning and return read-only value notApplicable(3). If the value cannot be changed (because cgfeb100ConfigMode(7) has the value hardware(2)) and Autonegotiation is enabled, these variables return the read- only values enabledRO(4) or disabledRO(5).
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3), enabledRO(4), disabledRO(5)  

cgfeb100TPAdv1000HDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.29
Enable/disable control for these advertised autonegotiation modes. If autonegotiation is disabled (because cgfeb100TpAutonegot(24) has the value disabled(2) or cgfeb100ConfigMode(7) has the value hardware(2) and the Autonegotiation hardware switch is disabled), then these variables have no meaning and return read-only value notApplicable(3). If the value cannot be changed (because cgfeb100ConfigMode(7) has the value hardware(2)) and Autonegotiation is enabled, these variables return the read- only values enabledRO(4) or disabledRO(5).
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3), enabledRO(4), disabledRO(5)  

cgfeb100TPAdv1000FDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.30
Enable/disable control for these advertised autonegotiation modes. If autonegotiation is disabled (because cgfeb100TpAutonegot(24) has the value disabled(2) or cgfeb100ConfigMode(7) has the value hardware(2) and the Autonegotiation hardware switch is disabled), then these variables have no meaning and return read-only value notApplicable(3). If the value cannot be changed (because cgfeb100ConfigMode(7) has the value hardware(2)) and Autonegotiation is enabled, these variables return the read- only values enabledRO(4) or disabledRO(5).
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3), enabledRO(4), disabledRO(5)  

cgfeb100TPLpAdvPause 1.3.6.1.4.1.868.2.4.1.2.2.23.1.31
This read-only variable shows the pause capability advertised by the twisted pair port's link partner. Values 1 through 4 for this variable are the same as those for cgfeb100TpAdvPause(38). If the device does not support the reporting of link partner autonegotiation or cgfeb100TpAutonegot(24) has the value disabled(2), this variable will have the value notApplicable(5).
OBJECT-TYPE    
  INTEGER symetric(1), asymRX(2), asymTX(3), disabled(4), notApplicable(5)  

cgfeb100TPLpAdv10HDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.32
This read-only variable shows twisted pair port's link partner's willingness to connect at 10Mbps Half Duplex. If the device does not support the reporting of link partner autonegotiation or cgfeb100TpAutonegot(24) has the value disabled(2), this variable will have the value notApplicable(3).
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cgfeb100TPLpAdv10FDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.33
This read-only variable shows twisted pair port's link partner's willingness to connect at 10Mbps Full Duplex. If the device does not support the reporting of link partner autonegotiation or cgfeb100TpAutonegot(24) has the value disabled(2), this variable will have the value notApplicable(3).
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cgfeb100TPLpAdv100HDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.34
This read-only variable shows twisted pair port's link partner's willingness to connect at 100Mbps Half Duplex. If the device does not support the reporting of link partner autonegotiation or cgfeb100TpAutonegot(24) has the value disabled(2), this variable will have the value notApplicable(3).
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cgfeb100TPLpAdv100FDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.35
This read-only variable shows twisted pair port's link partner's willingness to connect at 100Mbps Full Duplex. If the device does not support the reporting of link partner autonegotiation or cgfeb100TpAutonegot(24) has the value disabled(2), this variable will have the value notApplicable(3).
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cgfeb100TPLpAdv1000HDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.36
This read-only variable shows twisted pair port's link partner's willingness to connect at 1000Mbps Half Duplex. If the device does not support the reporting of link partner autonegotiation or cgfeb100TpAutonegot(24) has the value disabled(2), this variable will have the value notApplicable(3).
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cgfeb100TPLpAdv1000FDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.37
This read-only variable shows twisted pair port's link partner's willingness to connect at 1000Mbps Full Duplex. If the device does not support the reporting of link partner autonegotiation or cgfeb100TpAutonegot(24) has the value disabled(2), this variable will have the value notApplicable(3).
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cgfeb100TPAdvPause 1.3.6.1.4.1.868.2.4.1.2.2.23.1.38
Enable/disable control for autonegotiation advertising of Twisted Pair Pause capability. Selectable values are symmetric(1), asymRX(2) (asymmetric, pause frames flow towards the converter), asymTX(3) (asymmetric, pause frames flow towards the link partner), and disabled(4). If autonegotiation is disabled (because cgfeb100TpAutonegot(24) has the value disabled(2) or cgfeb100ConfigMode(7) has the value hardware(2) and the Autonegotiation hardware switch is disabled), then this variable has no meaning and the read-only value notApplicable(5) is returned. When cgfeb100TpQosPause(39) has the value disabled(2), negotiated pause is suppressed and the read-only value notApplicable(5) is returned. If cgfeb100ConfigMode(7) has the value hardware(2) and the Autonegotiation hardware switch is enabled, then one of the following read-only values will be returned: symmetricRO(6), asymRXRO(7) (asymmetric, pause frames flow towards the converter), asymTXRO(8) (asymmetric, pause frames flow towards the link partner), and disabledRO(9).
OBJECT-TYPE    
  INTEGER symetric(1), asymRX(2), asymTX(3), disabled(4), notApplicable(5), symmetricRO(6), asymRXRO(7), asymTXRO(8), disabledRO(9)  

cgfeb100TPQosPause 1.3.6.1.4.1.868.2.4.1.2.2.23.1.39
This variable allows Twisted Pair Quality Of Service Pause to be enabled or disabled. When cgfeb100QosEnabled(12) is set to enabled(1) and this variable is set to disabled(2), any pause functionality negotiated according to cgfeb100TpAdvPause(38) is suppressed. When cgfeb100QosEnabled(12) is set to disabled(2), this variable has the read-only value notApplicable(3).
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cgfeb100TPSacCfg 1.3.6.1.4.1.868.2.4.1.2.2.23.1.40
This variable allows Source Address Change traps to be enabled or disabled. If enabled, 'Error' traps will be sent as frequently one per polling cycle any time the ethernet source address of any packet received on the Twisted Pair interface is different from the last address received on that interface during the previous polling cycle.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cgfeb100TPSacStat 1.3.6.1.4.1.868.2.4.1.2.2.23.1.41
This read-only variable has the value changed(1) if the Ethernet source address received on the Twisted Pair interface changed since the device's previous report to the Mangement Module, and the value constant(2) otherwise. To cause the Management Module to generate a trap when this occurs, set cgfeb100SacConfig(41) to enabled(1).
OBJECT-TYPE    
  INTEGER changed(1), constant(2)  

cgfeb100ConnB 1.3.6.1.4.1.868.2.4.1.2.2.23.1.42
The style of Fiber connector built into this device.
OBJECT-TYPE    
  CpsConnector  


cgfeb100FiberFullDuplexCfg 1.3.6.1.4.1.868.2.4.1.2.2.23.1.44
The desired duplex setting of the Fiber interface. This can be set to fdx(1) (full duplex) or hdx(2) (half duplex). When cgfeb100TpAutonegot(24) has the value enabled(1) or cgfeb100ConfigMode(7) has the value hardware(2), this variable has the read-only value auto(3).
OBJECT-TYPE    
  INTEGER fdx(1), hdx(2), auto(3)  

cgfeb100FiberFullDuplexStat 1.3.6.1.4.1.868.2.4.1.2.2.23.1.45
The actual duplex behavior of the Fiber interface: fdx(1) (full duplex) or hdx(2) (half duplex). If cgfeb100FiberAutonegot(46) has the value disabled(2) and this version of the device does not support manual fiber duplex control, Fiber duplex is forced to HDX. If cgfeb100FiberAutonegot(46) has the value enabled(1) and cgfeb100FiberLink(43) has the value down(2), then no duplex setting is available, and this variable has the value notApplicable(3).
OBJECT-TYPE    
  INTEGER fdx(1), hdx(2), notApplicable(3)  

cgfeb100FiberAutoNegot 1.3.6.1.4.1.868.2.4.1.2.2.23.1.46
Autonegotiation configuration. Fiber autonegotiation is limited to the duplex setting. The fiber's speed is fixed at 1000Mbps.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cgfeb100FiberAdv1000HDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.47
Enable/disable control for these advertised autonegotiation modes. If autonegotiation is disabled (because cgfeb100TpAutonegot(24) has the value disabled(2) or cgfeb100ConfigMode(7) has the value hardware(2) and the Autonegotiation hardware switch is disabled), then these variables have no meaning and return read-only value notApplicable(3). If the value cannot be changed (because cgfeb100ConfigMode(7) has the value hardware(2)) and Autonegotiation is enabled, these variables return the read-only values enabledRO(4) or disabledRO(5). If manual control of Fiber Autonegotiaion advertised modes is not supported by the device, this variable has no meaning and the read-only value notApplicable(3) is returned.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cgfeb100FiberAdv1000FDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.48
Enable/disable control for these advertised autonegotiation modes. If autonegotiation is disabled (because cgfeb100TpAutonegot(24) has the value disabled(2) or cgfeb100ConfigMode(7) has the value hardware(2) and the Autonegotiation hardware switch is disabled), then these variables have no meaning and return read-only value notApplicable(3). If the value cannot be changed (because cgfeb100ConfigMode(7) has the value hardware(2)) and Autonegotiation is enabled, these variables return the read-only values enabledRO(4) or disabledRO(5). If manual control of Fiber Autonegotiaion advertised modes is not supported by the device, this variable has no meaning and the read-only value notApplicable(3) is returned.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3), enabledRO(4), disabledRO(5)  

cgfeb100FiberLpAdv1000HDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.49
This configuration setting controls whether or not each port advertises willingness to connect at 1000Mbps, half duplex. This setting is not supported on fiber ports, and is ignored when autonegotiation is disabled.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3), enabledRO(4), disabledRO(5)  

cgfeb100FiberLpAdv1000FDX 1.3.6.1.4.1.868.2.4.1.2.2.23.1.50
This configuration setting controls whether or not each port advertises willingness to connect at 1000Mbps, full duplex. This setting is not supported on fiber ports, and is ignored when autonegotiation is disabled.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

cgfeb100FiberLpAdvPause 1.3.6.1.4.1.868.2.4.1.2.2.23.1.51
This read-only variable shows the pause capability advertised by the fiber port's link partner. Values 1 through 4 for this variable are the same as those for cgfeb100TpAdvPause(38). If the device does not support the reporting of link partner autonegotiation or cgfeb100FiberAutonegot(46) has the value disabled(2), this variable will have the value notApplicable(5).
OBJECT-TYPE    
  INTEGER symetric(1), asymRX(2), asymTX(3), disabled(4), notApplicable(5)  

cgfeb100FiberAdvPause 1.3.6.1.4.1.868.2.4.1.2.2.23.1.52
Enable/disable control for autonegotiation advertising of Fiber Pause capability. Selectable values are symmetric(1), asymRX(2) (asymmetric, pause frames flow towards the converter), asymTX(3) (asymmetric, pause frames flow towards the link partner), and disabled(4). If autonegotiation is disabled (because cgfeb100FiberAutonegot(46) has the value disabled(2) or cgfeb100ConfigMode(7) has the value hardware(2) and the Autonegotiation hardware switch is disabled), then this variable has no meaning and the read-only value notApplicable(5) is returned. cgfeb100FiberQosPause(53) has the value disabled(2), negotiated pause is suppressed and the read-only value notApplicable(5) is returned. If cgfeb100ConfigMode(7) has the value hardware(2) and the Autonegotiation hardware switch is enabled, then one of the following read-only values will be returned: symmetricRO(6), asymRXRO(7) (asymmetric, pause frames flow towards the converter), asymTXRO(8) (asymmetric, pause frames flow towards the link partner), and disabledRO(9).
OBJECT-TYPE    
  INTEGER symetric(1), asymRX(2), asymTX(3), disabled(4), notApplicable(5), symetricRO(6), asymRXRO(7), asymTXRO(8), disabledRO(9)  

cgfeb100FiberQosPause 1.3.6.1.4.1.868.2.4.1.2.2.23.1.53
This variable allows Fiber Quality Of Service Pause to be enabled or disabled. When cgfeb100QosEnabled(12) is set to enabled(1) and this variable is set to disabled(2), any pause functionality negotiated according to cgfeb100FiberAdvPause(52) is suppressed. When cgfeb100QosEnabled(12) is set to disabled(2), this variable has the read-only value notApplicable(3).
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cgfeb100FiberSacCfg 1.3.6.1.4.1.868.2.4.1.2.2.23.1.54
This variable allows Source Address Change traps to be enabled or disabled. If enabled, 'Error' traps will be sent as frequently one per polling cycle any time the ethernet source address of any packet received on the Fiber interface is different from the last address received on that interface during the previous polling cycle.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cgfeb100FiberSacStat 1.3.6.1.4.1.868.2.4.1.2.2.23.1.55
This read-only variable has the value changed(1) if the Ethernet source address received on the fiber interface changed since the device's previous report to the Mangement Module, and the value constant(2) otherwise. To cause the Management Module to generate a trap when this occurs, set cgfeb100FiberSacConfig(54) to enabled(1).
OBJECT-TYPE    
  INTEGER changed(1), constant(2)  

cgfeb100MonitorTap 1.3.6.1.4.1.868.2.4.1.2.2.23.1.56
Before reading this description, see cgfeb100MonitorType(10). This variable controls which side of the fiber port (transmit(1) or receive(2)) is monitored by the monitoring port. If no monitoring port is present, this variable has the value notInstalled(3).
OBJECT-TYPE    
  INTEGER transmit(1), receive(2), notInstalled(3)  

cgfeb100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.23.1.57
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

crmfe100Table 1.3.6.1.4.1.868.2.4.1.2.2.24
Sparse table containing one entry for each CRMFE100 in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Crmfe100Entry

crmfe100Entry 1.3.6.1.4.1.868.2.4.1.2.2.24.1
Status and configuration entries for a single CRMFE100
OBJECT-TYPE    
  Crmfe100Entry  

crmfe100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.24.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

crmfe100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.24.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

crmfe100Groups 1.3.6.1.4.1.868.2.4.1.2.2.24.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CRMFE100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

crmfe100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.24.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

crmfe100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.24.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

crmfe100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.24.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  

crmfe100ConnA 1.3.6.1.4.1.868.2.4.1.2.2.24.1.7
The style of Fiber connector built into this device
OBJECT-TYPE    
  CpsConnector  

crmfe100ConnB 1.3.6.1.4.1.868.2.4.1.2.2.24.1.8
The style of Copper connector built into this device
OBJECT-TYPE    
  CpsConnector  



crmfe100Fault 1.3.6.1.4.1.868.2.4.1.2.2.24.1.11
Value is yes(1) when either CopperLink or FiberLink has value linkDown(2)
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

crmfe100Autonegot 1.3.6.1.4.1.868.2.4.1.2.2.24.1.12
Autonegotiation configuration for this device.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

crmfe100Enabled 1.3.6.1.4.1.868.2.4.1.2.2.24.1.13
When the Enabled configuration item is set to no(2), the converter passes no network traffic in either direction.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

crmfe100Pause 1.3.6.1.4.1.868.2.4.1.2.2.24.1.14
The Pause feature allows Ethernet MACs that support it to send data pacing 'Pause' messages to each other. Support for Pause is negotiated at the physical level and passed up to the MAC. While the MAC's Pause messages themselves can pass over the fiber link that this pair of media converters introduces, the TP physical layer negotiations to enable Pause can not. Therefore, if both end station MACs support Pause and wish to use it, the Pause negotiation must be re-generated by the media converters on both ends. By setting this configuration option to enabled(1), you are indicating to the local twisted pair station that the twisted pair station on the other side of the other media converter supports Pause and wishes to use it. This variable must be set consistently on both of the paired media converters.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

crmfe100LinkPassThrough 1.3.6.1.4.1.868.2.4.1.2.2.24.1.15
This configuration item allows Link Pass Through to be enabled(1) or disabled(2). Link Passthrough causes loss of link on one side of a media converter to be passed through to the other side, so that upstream equipment can see fault conditions that would otherwise be hidden by the media converters.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

crmfe100AutoCross 1.3.6.1.4.1.868.2.4.1.2.2.24.1.16
On certain devices, it is possible for hardware to automatically correct errors in cable selection, making the distinction between a 'straight through' cable and a 'crossover' cable unimportant. This capability is known as Auto Cross. When disabled, the port reverts to MDI mode.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

crmfe100TPActivity 1.3.6.1.4.1.868.2.4.1.2.2.24.1.17
Twisted Pair Activity. Some versions of the CRMFE100 do not support the reporting of interface activity. The value of this variable for such a device will be notApplicable.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

crmfe100FiberActivity 1.3.6.1.4.1.868.2.4.1.2.2.24.1.18
Fiber Activity. Some versions of the CRMFE100 do not support the reporting of interface activity. The value of this variable for such a device will be notApplicable.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

crmfe100ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.24.1.19
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

crmfe100FarEndFault 1.3.6.1.4.1.868.2.4.1.2.2.24.1.20
Far End Fault configuration of this device. Far End Fault causes the fiber transmitter to generate a Far End Fault pattern upon the loss of a receiver signal detect. When the receiver detects signal again, the transmitter stops transmitting the Far End Fault pattern.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

crmfe100NetworkMode 1.3.6.1.4.1.868.2.4.1.2.2.24.1.21
Read-only indicator for High Speed Token Ring jumper configuration. If the variable reads tokenRing(1), then the converter is jumpered for High Speed Token Ring mode. If the variable reads ethernet(2), then the converter is jumpered for Ethernet mode. The jumper settings for the converters on both ends of the fiber must be the same.
OBJECT-TYPE    
  INTEGER tokenRing(1), ethernet(2)  

crmfe100UpTime 1.3.6.1.4.1.868.2.4.1.2.2.24.1.22
Time since the last reboot in Time Ticks (hundredths of seconds). If the value 0 is written to this variable, the timer is reset. No other write value is accepted.
OBJECT-TYPE    
  TimeTicks  

crmfe100FirmwareRevision 1.3.6.1.4.1.868.2.4.1.2.2.24.1.23
Firmware revision level of this CRMFE100.
OBJECT-TYPE    
  INTEGER  

crmfe100RmtDetected 1.3.6.1.4.1.868.2.4.1.2.2.24.1.24
Has the value yes(1) if management communcations have been established with a remote media converter.
OBJECT-TYPE    
  INTEGER detected(1), notDetected(2)  



crmfe100RmtFault 1.3.6.1.4.1.868.2.4.1.2.2.24.1.27
Value is yes(1) when either TPLink or FiberLink has value linkDown(2)
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

crmfe100RmtAutonegot 1.3.6.1.4.1.868.2.4.1.2.2.24.1.28
Autonegotiation configuration for this device.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

crmfe100RmtPause 1.3.6.1.4.1.868.2.4.1.2.2.24.1.29
The Pause feature allows Ethernet MACs that support it to send data pacing 'Pause' messages to each other. Support for Pause is negotiated at the physical level and passed up to the MAC. While the MAC's Pause messages themselves can pass over the fiber link that this pair of media converters introduces, the TP physical layer negotiations to enable Pause can not. Therefore, if both end station MACs support Pause and wish to use it, the Pause negotiation must be re-generated by the media converters on both ends. By setting this configuration option to enabled(1), you are indicating to the local twisted pair station that the twisted pair station on the other side of the other media converter supports Pause and wishes to use it. This variable must be set consistently on both of the paired media converters.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

crmfe100RmtLinkPassThrough 1.3.6.1.4.1.868.2.4.1.2.2.24.1.30
This configuration item allows Link Pass Through to be enabled(1) or disabled(2). Link Passthrough causes loss of link on one side of a media converter to be passed through to the other side, so that upstream equipment can see fault conditions that would otherwise be hidden by the media converters.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

crmfe100RmtAutoCross 1.3.6.1.4.1.868.2.4.1.2.2.24.1.31
On certain devices, it is possible for hardware to automatically correct errors in cable selection, making the distinction between a 'straight through' cable and a 'crossover' cable unimportant. This capability is known as Auto Cross. When disabled, the port reverts to MDI mode.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

crmfe100RmtTPActivity 1.3.6.1.4.1.868.2.4.1.2.2.24.1.32
Twisted Pair Activity. Some versions of the CRMFE100 do not support the reporting of interface activity. The value of this variable for such a device will be notApplicable.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

crmfe100RmtFiberActivity 1.3.6.1.4.1.868.2.4.1.2.2.24.1.33
Fiber Activity. Some versions of the CRMFE100 do not support the reporting of interface activity. The value of this variable for such a device will be notApplicable.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notSupported(3)  

crmfe100RmtConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.24.1.34
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2), notApplicable(3)  

crmfe100RmtFarEndFault 1.3.6.1.4.1.868.2.4.1.2.2.24.1.35
Far End Fault configuration of this device. Far End Fault causes the fiber transmitter to generate a Far End Fault pattern upon the loss of a receiver signal detect. When the receiver detects signal again, the transmitter stops transmitting the Far End Fault pattern.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

crmfe100RmtLoopback 1.3.6.1.4.1.868.2.4.1.2.2.24.1.36
When Remote Loopback is enabled, all packets sent out from the local fiber interface are reflected back by the remote converter rather than being passed out through the remote twisted pair interface, and all packets received on the remote Twisted Pair interface are discarded.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

crmfe100RmtNetworkMode 1.3.6.1.4.1.868.2.4.1.2.2.24.1.37
Read-only indicator for High Speed Token Ring jumper configuration. If the variable reads tokenRing(1), then the converter is jumpered for High Speed Token Ring mode. If the variable reads ethernet(2), then the converter is jumpered for Ethernet mode. The jumper settings for the converters on both ends of the fiber must be the same.
OBJECT-TYPE    
  INTEGER tokenRing(1), ethernet(2), notApplicable(3)  

crmfe100RmtUpTime 1.3.6.1.4.1.868.2.4.1.2.2.24.1.38
Time since the last reboot in Time Ticks (hundredths of seconds). If the value 0 is written to this variable, the timer is reset. No other write value is accepted.
OBJECT-TYPE    
  TimeTicks  

crmfe100TxFxBwa 1.3.6.1.4.1.868.2.4.1.2.2.24.1.39
This variable allows the control of bandwidth allocation. The value of this variable is entered in Kilobytes per Second, and is automatically rounded to the nearest 64KBps. A value of zero disables data transfer, and the maximum value is 12224KBps. Data traffic is measured from the beginning of each second. Once the traffic reaches the cap specified, all traffic is discarded until the start of the next second, when the counters are reset and traffic begins to flow again. crmfe100TxFxBwa(39) limits the data flowing from the Twisted Pair interface to the Fiber interface.
OBJECT-TYPE    
  INTEGER  

crmfe100FxTxBwa 1.3.6.1.4.1.868.2.4.1.2.2.24.1.40
This variable allows the control of bandwidth allocation. The value of this variable is entered in Kilobytes per Second, and is automatically rounded to the nearest 64KBps. A value of zero disables data transfer, and the maximum value is 12224KBps. Data traffic is measured from the beginning of each second. Once the traffic reaches the cap specified, all traffic is discarded until the start of the next second, when the counters are reset and traffic begins to flow again. crmfe100FxTxBwa(39) limits the data flowing from the fiber interface to the twisted pair interface.
OBJECT-TYPE    
  INTEGER  

crmfe100TxBytesH 1.3.6.1.4.1.868.2.4.1.2.2.24.1.41
These variables measure the traffic (in Bytes) received by the two interfaces of the converter (and therefore transmitted by the opposite interface). 'Tx' refers to data received by the Twisted Pair interface (and transmitted on the Fiber interface), and 'Fx' refers to data received on the Fiber interface (and transmitted on the Twisted Pair interface). In order to limit each variable to the 32-bit maximum commonly supported in the SNMP world, these 64-bit counters are split into a high-order and low-order 32-bit sections. Transition Networks' applications generally treat the High order portion of the counter as a counter of the number of times the Low order section has wrapped to 0. To reconstruct the original 64-bit value, multiply the 'High' section by 2^32 and add the 'Low' section. If you write the value 0 to any of these four variables, all four are reset to zero.
OBJECT-TYPE    
  INTEGER  

crmfe100TxBytesL 1.3.6.1.4.1.868.2.4.1.2.2.24.1.42
See the DESCRIPTION for cfmfe100TxBytesH(42) above.
OBJECT-TYPE    
  INTEGER  

crmfe100FxBytesH 1.3.6.1.4.1.868.2.4.1.2.2.24.1.43
See the DESCRIPTION for cfmfe100TxBytesH(42) above.
OBJECT-TYPE    
  INTEGER  

crmfe100FxBytesL 1.3.6.1.4.1.868.2.4.1.2.2.24.1.44
See the DESCRIPTION for cfmfe100TxBytesH(42) above.
OBJECT-TYPE    
  INTEGER  

crmfe100MscRxBytes 1.3.6.1.4.1.868.2.4.1.2.2.24.1.45
This variable measures the traffic (in Bytes) received and transmitted by the Management Subchannel within the Fiber interface. 'Management Subchannel' refers to the transfer of management data to and from the Remote SRMFExxx in the inter-packet gaps normally found in Ethernet traffic. This allows management data to be transferred with no reduction in the bandwidth available for normal network traffic. If you write the value 0 to this variable or crmfe100MscTxBytes(47), both are reset to zero.
OBJECT-TYPE    
  INTEGER  

crmfe100MscTxBytes 1.3.6.1.4.1.868.2.4.1.2.2.24.1.46
This variable measures the traffic (in Bytes) received and transmitted by the Management Subchannel within the Fiber interface. 'Management Subchannel' refers to the transfer of management data to and from the Remote SRMFExxx in the inter-packet gaps normally found in Ethernet traffic. This allows management data to be transferred with no reduction in the bandwidth available for normal network traffic. If you write the value 0 to this variable or crmfe100MscRxBytes(46), both are reset to zero.
OBJECT-TYPE    
  INTEGER  

crmfe100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.24.1.47
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

crmfe100MbTxFxBwa 1.3.6.1.4.1.868.2.4.1.2.2.24.1.48
This variable allows the control of bandwidth allocation. The value of this variable is entered in Megabits per Second, and is automatically rounded to the nearest 64KBps. A value of zero disables data transfer, and the maximum value is 12224KBps. Data traffic is measured from the beginning of each second. Once the traffic reaches the cap specified, all traffic is discarded until the start of the next second, when the counters are reset and traffic begins to flow again. crmfe100MbTxFxBwa(48) limits the data flowing from the Twisted Pair interface to the Fiber interface. This variable does the same thing as crmfe100TxFxBwa(39), only the units are different.
OBJECT-TYPE    
  INTEGER  

crmfe100MbFxTxBwa 1.3.6.1.4.1.868.2.4.1.2.2.24.1.49
This variable allows the control of bandwidth allocation. The value of this variable is entered in Megabits per Second, and is automatically rounded to the nearest 64KBps. A value of zero disables data transfer, and the maximum value is 12224KBps. Data traffic is measured from the beginning of each second. Once the traffic reaches the cap specified, all traffic is discarded until the start of the next second, when the counters are reset and traffic begins to flow again. crmfe100MbFxTxBwa(49) limits the data flowing from the fiber interface to the twisted pair interface. This variable does the same thing as crmfe100TxFxBwa(40), only the units are different.
OBJECT-TYPE    
  INTEGER  

crs2f100Table 1.3.6.1.4.1.868.2.4.1.2.2.25
Sparse table containing one entry for each CRS2F100 in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Crs2f100Entry

crs2f100Entry 1.3.6.1.4.1.868.2.4.1.2.2.25.1
Status and configuration entries for a single CRS2F100
OBJECT-TYPE    
  Crs2f100Entry  

crs2f100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.25.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

crs2f100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.25.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

crs2f100Groups 1.3.6.1.4.1.868.2.4.1.2.2.25.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CRS2F100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

crs2f100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.25.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

crs2f100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.25.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

crs2f100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.25.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  

crs2f100ConnA 1.3.6.1.4.1.868.2.4.1.2.2.25.1.7
The style of Fiber connector built into this device
OBJECT-TYPE    
  CpsConnector  

crs2f100ConnB 1.3.6.1.4.1.868.2.4.1.2.2.25.1.8
The style of Copper connector built into this device
OBJECT-TYPE    
  CpsConnector  


crs2f100Fault 1.3.6.1.4.1.868.2.4.1.2.2.25.1.10
Value is yes(1) when FiberLink has value linkDown(2)
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

crs2f100FirmwareRevision 1.3.6.1.4.1.868.2.4.1.2.2.25.1.11
The Firmware Revision MIB Variable reports the revision of software running on the processor on this particular device. You can discover the revisions on these devices by entering the PICREV command at the command line interface. Device Firmware Revisions are normally discussed in terms of a single letter, e.g. revision 'B'. However, when the firmware revision is displayed by generic MIB processing code that is unaware of this convention, the revision is displayed as a decimal value. The table in crs2f100.html provides some examples of how decimal revision values correspond to letter revision values.
OBJECT-TYPE    
  INTEGER  

crs2f100Loopback 1.3.6.1.4.1.868.2.4.1.2.2.25.1.12
Loopback is a testing aid available on several different products. When Loopback is enabled on an interface, all data that is sent to the interface is reflected back to the sender, and the actual condition (or even existence) of the equipment on the opposite interface is ignored.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

crs2f100DCE 1.3.6.1.4.1.868.2.4.1.2.2.25.1.13
An indication of whether this device is attached to a DCE (a modem) or a DTE (a terminal or computer).
OBJECT-TYPE    
  INTEGER dCE(1), dTE(2)  

crs2f100CopperActivity 1.3.6.1.4.1.868.2.4.1.2.2.25.1.14
The activity indicator has the value yes(1) when the hardware has recently detected network traffic on the associated network port, and no(2) otherwise.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

crs2f100ConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.25.1.15
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device.
OBJECT-TYPE    
  INTEGER software(1), hardware(2)  

crs2f100RmtDetected 1.3.6.1.4.1.868.2.4.1.2.2.25.1.16
Has the value yes(1) if management communcations have been established with a remote media device.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

crs2f100RmtLoopback 1.3.6.1.4.1.868.2.4.1.2.2.25.1.17
Loopback is a testing aid available on several different products. When Loopback is enabled on an interface, all data that is sent to the interface is reflected back to the sender, and the actual condition (or even existence) of the equipment on the opposite interface is ignored. When no remote device is present, this variable has the value notApplicable(3).
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

crs2f100RmtDCE 1.3.6.1.4.1.868.2.4.1.2.2.25.1.18
This variable describes the status of a remotely managed device. This is an indicator of whether this device is attached to a DCE (a modem) or a DTE (a terminal or computer). When no remote device is present, this variable has the value notApplicable(3).
OBJECT-TYPE    
  INTEGER dCE(1), dTE(2), notApplicable(3)  

crs2f100RmtCopperActivity 1.3.6.1.4.1.868.2.4.1.2.2.25.1.19
The activity indicator has the value yes(1) when the hardware has recently detected network traffic on the associated network port, and no(2) otherwise. When no remote device is present, this variable has the value notApplicable(3).
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

crs2f100RmtConfigMode 1.3.6.1.4.1.868.2.4.1.2.2.25.1.20
This device has a jumper or switch that disables software management of the device. When ConfigMode is hardware(2), SNMP management is disabled, and all configuration control comes from physical switches or jumpers on the device. When no remote device is present, this variable has the value notApplicable(3).
OBJECT-TYPE    
  INTEGER software(1), hardware(2), notApplicable(3)  

crs2f100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.25.1.21
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

crs4f100Table 1.3.6.1.4.1.868.2.4.1.2.2.26
Sparse table containing one entry for each CRS4F100 in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    Crs4f100Entry

crs4f100Entry 1.3.6.1.4.1.868.2.4.1.2.2.26.1
Status and configuration entries for a single CRS4F100
OBJECT-TYPE    
  Crs4f100Entry  

crs4f100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.26.1.1
The serial number (BIA) of the cabinet in which the device is installed
OBJECT-TYPE    
  INTEGER  

crs4f100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.26.1.2
The slot in which the device is installed
OBJECT-TYPE    
  INTEGER  

crs4f100Groups 1.3.6.1.4.1.868.2.4.1.2.2.26.1.3
User-defined keywords that group this device together with other devices under a user-defined scheme. By placing matching keywords in cpsGroupCtrl.0, the agent can be instructed to apply configuration changes simultaneously to all group members rather than to individual devices. Every Groups string has three automatically defined implied values: 1) The model family of the device, e.g. 'CRS4F100' 2) The serial number of the cabinet in which the device is installed, in decimal with no leading zeroes, e.g. '12345', and 3) same as 2, with the slot in which the device is installed appended, enclosed in square brackets. e.g. '12345[9]'
OBJECT-TYPE    
  DisplayString  

crs4f100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.26.1.4
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

crs4f100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.26.1.5
yes(1) indicates that the conditions specified in cpsGroupCtrl.0 match the Groups value for this device. no(2) means that there is no match. notApplicable(3) indicates that cpsGroupCtrl.0 is null and therefore no comparison was performed.
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

crs4f100SerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.26.1.6
The serial number of this device
OBJECT-TYPE    
  INTEGER  

crs4f100ConnA 1.3.6.1.4.1.868.2.4.1.2.2.26.1.7
The style of Fiber connector built into this device
OBJECT-TYPE    
  CpsConnector  

crs4f100ConnB 1.3.6.1.4.1.868.2.4.1.2.2.26.1.8
The style of Copper connector built into this device
OBJECT-TYPE    
  CpsConnector  


crs4f100Fault 1.3.6.1.4.1.868.2.4.1.2.2.26.1.10
Value is yes(1) when FiberLink has value linkDown(2)
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

crs4f100FirmwareRevision 1.3.6.1.4.1.868.2.4.1.2.2.26.1.11
The Firmware Revision MIB Variable reports the revision of software running on the processor on this particular device. You can discover the revisions on these devices by entering the PICREV command at the command line interface. Device Firmware Revisions are normally discussed in terms of a single letter, e.g. revision 'B'. However, when the firmware revision is displayed by generic MIB processing code that is unaware of this convention, the revision is displayed as a decimal value. The table in crs4f100.html provides some examples of how decimal revision values correspond to letter revision values.
OBJECT-TYPE    
  INTEGER  

crs4f100CopperActivity 1.3.6.1.4.1.868.2.4.1.2.2.26.1.12
The activity indicator has the value yes(1) when the hardware has recently detected network traffic on the associated network port, and no(2) otherwise.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

crs4f100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.26.1.13
When the value is clean(1)Device and Management Module cache are synchronized, no automatic corrections to configuration will occur. When the value is dirty(2) Device and Management Module cache are not synchronized. The configuration currently displayed by the application has not been validated by the device. The device may need to correct the configuration, in which case the displayed configuration will change.
OBJECT-TYPE    
  INTEGER clean(1), dirty(2)  

cmefg100Table 1.3.6.1.4.1.868.2.4.1.2.2.27
Generated CMEFG100 MIB Version 041110a
OBJECT-TYPE    
  SEQUENCE OF  
    Cmefg100Entry

cmefg100Entry 1.3.6.1.4.1.868.2.4.1.2.2.27.1
Status and configuration entries for a single CMEFG100
OBJECT-TYPE    
  Cmefg100Entry  

cmefg100SubDeviceIndex 1.3.6.1.4.1.868.2.4.1.2.2.27.1.1
If the name of a particular MIB variable does not end in 'Tbl', then it uses the placeholder value '1' in the subdevice index column.
OBJECT-TYPE    
  INTEGER  

cmefg100BiaIndex 1.3.6.1.4.1.868.2.4.1.2.2.27.1.2
OBJECT-TYPE    
  INTEGER  

cmefg100SlotIndex 1.3.6.1.4.1.868.2.4.1.2.2.27.1.3
OBJECT-TYPE    
  INTEGER  

cmefg100Groups 1.3.6.1.4.1.868.2.4.1.2.2.27.1.4
OBJECT-TYPE    
  DisplayString  

cmefg100MRevision 1.3.6.1.4.1.868.2.4.1.2.2.27.1.5
OBJECT-TYPE    
  INTEGER  

cmefg100CfgMatch 1.3.6.1.4.1.868.2.4.1.2.2.27.1.6
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cmefg100ImcLocEnable 1.3.6.1.4.1.868.2.4.1.2.2.27.1.7
Enable periodic upload of local Interface MIB Counters from CMEFG100 to Agent. cmefg100ImcxxxTbl subdevice 1=local tp, subdevice 2=local fiber.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cmefg100ImcLocReset 1.3.6.1.4.1.868.2.4.1.2.2.27.1.8
set to reset(1) to clear all local cmefg100Imc counters.
OBJECT-TYPE    
  INTEGER reset(1), doNothing(2)  

cmefg100ImcRmtEnable 1.3.6.1.4.1.868.2.4.1.2.2.27.1.9
Enable periodic upload of remote Interface MIB Counters from CMEFG100 to Agent. cmefg100ImcxxxTbl subdevice 3=remote tp, subdevice 4=remote fiber.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cmefg100ImcRmtReset 1.3.6.1.4.1.868.2.4.1.2.2.27.1.10
set to reset(1) to clear all remote cmefg100Imc counters.
OBJECT-TYPE    
  INTEGER reset(1), doNothing(2)  

cmefg100ImcRxAlignmentErrorsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.11
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxBroadcastPktsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.12
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxDropPktsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.13
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxExcessSizeDiscTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.14
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxFCSErrorsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.15
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxFragmentsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.16
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxGoodOctetsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.17
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxGoodOctetsWrapTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.18
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxJabbersTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.19
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxMulticastPktsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.20
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxOctetsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.21
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxOctetsWrapTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.22
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxOversizePktsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.23
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxPausePktsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.24
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxPkts1024to1522OctetsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.25
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxPkts128to255OctetsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.26
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxPkts256to511OctetsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.27
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxPkts512to1023OctetsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.28
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxPkts64OctetsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.29
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxPkts65to127OctetsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.30
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxQosOctetsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.31
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxQosOctetsWrapTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.32
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxQosPktsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.33
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxSAChangesTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.34
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxSymbolErrorTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.35
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxUndersizePktsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.36
OBJECT-TYPE    
  INTEGER  

cmefg100ImcRxUnicastPktsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.37
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxBroadcastPktsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.38
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxCollisionsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.39
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxDeferredTransmitTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.40
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxDropPktsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.41
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxExcessiveCollisionTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.42
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxFrameInDiscTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.43
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxLateCollisionTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.44
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxMulticastPktsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.45
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxMultipleCollisionTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.46
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxOctetsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.47
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxOctetsWrapTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.48
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxPausePktsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.49
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxQosOctetsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.50
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxQosOctetsWrapTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.51
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxQosPktsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.52
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxSingleCollisionTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.53
OBJECT-TYPE    
  INTEGER  

cmefg100ImcTxUnicastPktsTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.54
OBJECT-TYPE    
  INTEGER  

cmefg100LadCacheCmd 1.3.6.1.4.1.868.2.4.1.2.2.27.1.55
All variables starting with cmefg100Lad relate to the Learned MAC Address Database. Due to the large size of the LAD database and the limited memory within the Agent, the cache is loaded into the cache memory buffer only when it is requested via this MIB variable. Setting this var to loadCache commands the agent to upload the LAD from the device exactly one time. Note that the contents of this cache are NOT automatically refreshed. Setting this variable to 'release' causes the data in the cache to be purged, even if the cache buffer contains data of an entirely different type, such as the VLAN table cache. Thus, it is not necessary to know what type of data was most recently loaded into the cache buffer, but it is necessary to take care not to release data that is currently in use. A genErr will be returned if any other command involving reading or writing the LAD or the VLAN table is in progress.
OBJECT-TYPE    
  INTEGER loadCache(1), doNothing(2), release(3)  

cmefg100LadCacheState 1.3.6.1.4.1.868.2.4.1.2.2.27.1.56
This variable shows the current state of the Agent's cache buffer with respect to the Learned Address Database. A value of 'ready' means that the cache buffer contains a complete copy of the LAD that is less than 300 seconds old. A value of 'stale' means that the cache buffer contains a complete copy of the LAD that is more than 300 seconds old. A value of 'empty' means that the buffer has been purged, and the system is ready to accept a cmefg100LadCacheCmd of 'loadCache.' A value of 'transferring' means that no command can be issued and the cache cannot be read because data is currently being transferred into the cache buffer. The data may or may not be related to the LAD. A value of 'bufferBusy' means that the buffer contains a complete copy (ready or stale) of something other than the LAD. The contents of the buffer can be overwritten with the LAD by issuing a 'loadCache' command.
OBJECT-TYPE    
  INTEGER ready(1), empty(2), transferring(3), bufferBusy(4), stale(5)  

cmefg100LadEditCmd 1.3.6.1.4.1.868.2.4.1.2.2.27.1.57
Setting this var to 'write' causes LadEditMac, LadEditPort, and LadEditVid to be written (insert/overwrite as required) to the LAD. Setting this var to 'delete' causes the address represented by LadEditMac to be deleted from the LAD. Changes made are not reflected in the LAD cache until the device accepts them and the cache is reloaded. A genErr will be returned if any other command involving reading or writing the LAD or the VLAN table is in progress.
OBJECT-TYPE    
  INTEGER write(1), delete(2), doNothing(3)  

cmefg100LadEditMac 1.3.6.1.4.1.868.2.4.1.2.2.27.1.58
A plain-text representation of a MAC address to be used the next time cmefg100LadEditCmd is set to write or delete.
OBJECT-TYPE    
  OCTET STRING  

cmefg100LadEditPort 1.3.6.1.4.1.868.2.4.1.2.2.27.1.59
A port to be used the next time cmefg100LadEditCmd is set to write.
OBJECT-TYPE    
  INTEGER twistedPair(1), fiber(2), drop(3)  

cmefg100LadEditVid 1.3.6.1.4.1.868.2.4.1.2.2.27.1.60
A VLAN Id to be used the next time cmefg100LadEditCmd is set to write. Not valid when cmefg100VlanEnable is disabled(2)
OBJECT-TYPE    
  INTEGER  

cmefg100LadEntries 1.3.6.1.4.1.868.2.4.1.2.2.27.1.61
A count of the number of entries currently in the LAD Cache. See also cmefg100LadCacheState. If a LAD cache-filling transfer is in progress, this variable can be read for a progress report.
OBJECT-TYPE    
  INTEGER  

cmefg100LadMacTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.62
An Ethernet MAC address in the LAD table. The SubDeviceIndex is an arbitrary integer sequence number, range 1..cmefg100LadEntries. If cmefg100LadEntries is 0 (either because cmefg100LadCacheState is not 'ready/stale' or because there simply are no entries), this table contains a solitary dummy entry, SubDeviceIndex==1.
OBJECT-TYPE    
  MacAddress  

cmefg100LadPortTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.63
A port in the LAD table. Drop means 'forward to neither port' The SubDeviceIndex is an arbitrary integer sequence number, range 1..cmefg100LadEntries. If cmefg100LadEntries is 0 (either because cmefg100LadCacheState is not 'ready/stale' or because there simply are no entries), this table contains a solitary entry, SubDeviceIndex==1, value notApplicable.
OBJECT-TYPE    
  INTEGER twistedPair(1), fiber(2), drop(3), notApplicable(4)  

cmefg100LadStaticTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.64
An indication of whether the indexed entry in the LAD is static or dynamic. The SubDeviceIndex is an arbitrary integer sequence number, range 1..cmefg100LadEntries. If cmefg100LadEntries is 0 (either because cmefg100LadCacheState is not 'ready/stale' or because there simply are no entries), this table contains a solitary entry, SubDeviceIndex==1, value notApplicable.
OBJECT-TYPE    
  INTEGER static(1), dynamic(2), notApplicable(3)  

cmefg100LadVidTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.65
A VLAN Id in the LAD table. The SubDeviceIndex is an arbitrary integer sequence number, range 1..cmefg100LadEntries. If cmefg100LadEntries is 0 (either because cmefg100LadCacheState is not 'ready/stale' or because there simply are no entries), this table contains a solitary dummy entry, SubDeviceIndex==1. Always returns the dummy value '0' when cmefg100VlanEnable is disabled(2).
OBJECT-TYPE    
  INTEGER  

cmefg100LocColdstart 1.3.6.1.4.1.868.2.4.1.2.2.27.1.66
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cmefg100LocDmiRxPower 1.3.6.1.4.1.868.2.4.1.2.2.27.1.67
DMI: Diagnostic Monitoring Interface for fiber transceivers
OBJECT-TYPE    
  INTEGER  

cmefg100LocDmiRxPowerAlarm 1.3.6.1.4.1.868.2.4.1.2.2.27.1.68
OBJECT-TYPE    
  INTEGER normal(1), notSupported(2), lowWarn(3), highWarn(4), lowAlarm(5), highAlarm(6)  

cmefg100LocDmiTemp 1.3.6.1.4.1.868.2.4.1.2.2.27.1.69
In tenths of degrees C
OBJECT-TYPE    
  INTEGER  

cmefg100LocDmiTempAlarm 1.3.6.1.4.1.868.2.4.1.2.2.27.1.70
OBJECT-TYPE    
  INTEGER normal(1), notSupported(2), lowWarn(3), highWarn(4), lowAlarm(5), highAlarm(6)  

cmefg100LocDmiTxBiasAlarm 1.3.6.1.4.1.868.2.4.1.2.2.27.1.71
OBJECT-TYPE    
  INTEGER normal(1), notSupported(2), lowWarn(3), highWarn(4), lowAlarm(5), highAlarm(6)  

cmefg100LocDmiTxBiasCurrent 1.3.6.1.4.1.868.2.4.1.2.2.27.1.72
In microamperes
OBJECT-TYPE    
  INTEGER  

cmefg100LocDmiTxPower 1.3.6.1.4.1.868.2.4.1.2.2.27.1.73
In microwatts
OBJECT-TYPE    
  INTEGER  

cmefg100LocDmiTxPowerAlarm 1.3.6.1.4.1.868.2.4.1.2.2.27.1.74
OBJECT-TYPE    
  INTEGER normal(1), notSupported(2), lowWarn(3), highWarn(4), lowAlarm(5), highAlarm(6)  

cmefg100LocFiberAdv1000FDX 1.3.6.1.4.1.868.2.4.1.2.2.27.1.75
Read-only value notApplicable returned when autonegotiation is disabled
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cmefg100LocFiberAdv1000HDX 1.3.6.1.4.1.868.2.4.1.2.2.27.1.76
Read-only value notApplicable returned when autonegotiation is disabled
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cmefg100LocFiberAutoNegot 1.3.6.1.4.1.868.2.4.1.2.2.27.1.77
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cmefg100LocFiberConnA 1.3.6.1.4.1.868.2.4.1.2.2.27.1.78
OBJECT-TYPE    
  CpsConnector  

cmefg100LocFiberDuplex 1.3.6.1.4.1.868.2.4.1.2.2.27.1.79
Read-only values 3..5 are returned when autonegotiation is enabled
OBJECT-TYPE    
  INTEGER forceFDX(1), forceHDX(2), autoFDX(3), autoHDX(4), negotiating(5)  


cmefg100LocFiberPause 1.3.6.1.4.1.868.2.4.1.2.2.27.1.81
OBJECT-TYPE    
  INTEGER asymmetricRx(1), asymmetricTx(2), symmetric(3), disabled(4)  

cmefg100LocFiberQosPause 1.3.6.1.4.1.868.2.4.1.2.2.27.1.82
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cmefg100LocFiberSacEnable 1.3.6.1.4.1.868.2.4.1.2.2.27.1.83
Enable/disable traps for Source Address Change
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cmefg100LocFiberSacStatus 1.3.6.1.4.1.868.2.4.1.2.2.27.1.84
OBJECT-TYPE    
  INTEGER changed(1), constant(2)  

cmefg100LocFirmwareRevision 1.3.6.1.4.1.868.2.4.1.2.2.27.1.85
OBJECT-TYPE    
  INTEGER  

cmefg100LocFpgaRev 1.3.6.1.4.1.868.2.4.1.2.2.27.1.86
Field-Programmable Gate Array revision
OBJECT-TYPE    
  INTEGER  

cmefg100LocFxTxBwaKb 1.3.6.1.4.1.868.2.4.1.2.2.27.1.87
FX to TX bandwidth allocation, in Kbps
OBJECT-TYPE    
  INTEGER 1..122112  

cmefg100LocFxTxBwaMb 1.3.6.1.4.1.868.2.4.1.2.2.27.1.88
FX to TX bandwidth allocation, in Mbps
OBJECT-TYPE    
  INTEGER 1..1000  

cmefg100LocOamActiveMode 1.3.6.1.4.1.868.2.4.1.2.2.27.1.89
OAM: Operation, Administration, and Maintenance
OBJECT-TYPE    
  INTEGER active(1), passive(2)  

cmefg100LocOamAdminControl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.90
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cmefg100LocOamConfigRevision 1.3.6.1.4.1.868.2.4.1.2.2.27.1.91
OBJECT-TYPE    
  INTEGER  

cmefg100LocOamControlInUnknownOpcodes 1.3.6.1.4.1.868.2.4.1.2.2.27.1.92
OBJECT-TYPE    
  INTEGER  

cmefg100LocOamCriticalEvent 1.3.6.1.4.1.868.2.4.1.2.2.27.1.93
OBJECT-TYPE    
  INTEGER critical(1), normal(2)  

cmefg100LocOamDuplicateEventNotificationRx 1.3.6.1.4.1.868.2.4.1.2.2.27.1.94
OBJECT-TYPE    
  INTEGER  

cmefg100LocOamFramesLostDueToOamError 1.3.6.1.4.1.868.2.4.1.2.2.27.1.95
OBJECT-TYPE    
  INTEGER  

cmefg100LocOamInformationRx 1.3.6.1.4.1.868.2.4.1.2.2.27.1.96
OBJECT-TYPE    
  INTEGER  

cmefg100LocOamInformationTx 1.3.6.1.4.1.868.2.4.1.2.2.27.1.97
OBJECT-TYPE    
  INTEGER  

cmefg100LocOamLastGasp 1.3.6.1.4.1.868.2.4.1.2.2.27.1.98
OBJECT-TYPE    
  INTEGER failure(1), normal(2)  

cmefg100LocOamLinkEvents 1.3.6.1.4.1.868.2.4.1.2.2.27.1.99
OBJECT-TYPE    
  INTEGER supported(1), notSupported(2)  

cmefg100LocOamLinkFault 1.3.6.1.4.1.868.2.4.1.2.2.27.1.100
OBJECT-TYPE    
  INTEGER fault(1), normal(2)  

cmefg100LocOamLocDteDisc 1.3.6.1.4.1.868.2.4.1.2.2.27.1.101
discovery state
OBJECT-TYPE    
  INTEGER completed(1), notCompleted(2), unsatisfied(3)  

cmefg100LocOamLoopbackControlRx 1.3.6.1.4.1.868.2.4.1.2.2.27.1.102
OBJECT-TYPE    
  INTEGER  

cmefg100LocOamLoopbackControlTx 1.3.6.1.4.1.868.2.4.1.2.2.27.1.103
OBJECT-TYPE    
  INTEGER  

cmefg100LocOamMacAddress 1.3.6.1.4.1.868.2.4.1.2.2.27.1.104
The MAC address of the OAM entity.
OBJECT-TYPE    
  MacAddress  

cmefg100LocOamMaxOamPduSize 1.3.6.1.4.1.868.2.4.1.2.2.27.1.105
OBJECT-TYPE    
  INTEGER  

cmefg100LocOamMultiplexorState 1.3.6.1.4.1.868.2.4.1.2.2.27.1.106
OBJECT-TYPE    
  INTEGER forwarding(1), discarding(2)  

cmefg100LocOamOperStatus 1.3.6.1.4.1.868.2.4.1.2.2.27.1.107
OBJECT-TYPE    
  INTEGER linkFault(1), activeSendLocal(2), passiveWait(3), sendLocalRemote(4), sendLocalRemoteOk(5), sendAny(6)  

cmefg100LocOamOrgSpecificRx 1.3.6.1.4.1.868.2.4.1.2.2.27.1.108
OBJECT-TYPE    
  INTEGER  

cmefg100LocOamOrgSpecificTx 1.3.6.1.4.1.868.2.4.1.2.2.27.1.109
OBJECT-TYPE    
  INTEGER  

cmefg100LocOamParserState 1.3.6.1.4.1.868.2.4.1.2.2.27.1.110
OBJECT-TYPE    
  INTEGER forwarding(1), discarding(2), looping(3)  

cmefg100LocOamRmtDteDisc 1.3.6.1.4.1.868.2.4.1.2.2.27.1.111
OBJECT-TYPE    
  INTEGER completed(1), notCompleted(2), unsatisfied(3)  

cmefg100LocOamRmtLoopback 1.3.6.1.4.1.868.2.4.1.2.2.27.1.112
Indicates whether or not local has support to allow remote to initiate remote loopback mode.
OBJECT-TYPE    
  INTEGER supported(1), notSupported(2)  

cmefg100LocOamUnidirectional 1.3.6.1.4.1.868.2.4.1.2.2.27.1.113
OBJECT-TYPE    
  INTEGER supported(1), notSupported(2)  

cmefg100LocOamVarRetrieval 1.3.6.1.4.1.868.2.4.1.2.2.27.1.114
OBJECT-TYPE    
  INTEGER supported(1), notSupported(2)  

cmefg100LocSelfTestFailed 1.3.6.1.4.1.868.2.4.1.2.2.27.1.115
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cmefg100LocSerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.27.1.116
OBJECT-TYPE    
  INTEGER  

cmefg100LocTpAdv1000FDX 1.3.6.1.4.1.868.2.4.1.2.2.27.1.117
Read-only value notApplicable returned when autonegotiation is disabled
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cmefg100LocTpAdv1000HDX 1.3.6.1.4.1.868.2.4.1.2.2.27.1.118
Read-only value notApplicable returned when autonegotiation is disabled
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cmefg100LocTpAdv100FDX 1.3.6.1.4.1.868.2.4.1.2.2.27.1.119
Read-only value notApplicable returned when autonegotiation is disabled
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cmefg100LocTpAdv100HDX 1.3.6.1.4.1.868.2.4.1.2.2.27.1.120
Read-only value notApplicable returned when autonegotiation is disabled
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cmefg100LocTpAdv10FDX 1.3.6.1.4.1.868.2.4.1.2.2.27.1.121
Read-only value notApplicable returned when autonegotiation is disabled
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cmefg100LocTpAdv10HDX 1.3.6.1.4.1.868.2.4.1.2.2.27.1.122
Read-only value notApplicable returned when autonegotiation is disabled
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cmefg100LocTpAutoNegot 1.3.6.1.4.1.868.2.4.1.2.2.27.1.123
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cmefg100LocTpConnB 1.3.6.1.4.1.868.2.4.1.2.2.27.1.124
OBJECT-TYPE    
  CpsConnector  

cmefg100LocTpCross 1.3.6.1.4.1.868.2.4.1.2.2.27.1.125
OBJECT-TYPE    
  INTEGER forceMDI(1), forceMDI-X(2), auto(3)  

cmefg100LocTpDuplex 1.3.6.1.4.1.868.2.4.1.2.2.27.1.126
Read-only values 3..5 are returned when autonegotiation is enabled
OBJECT-TYPE    
  INTEGER forceFDX(1), forceHDX(2), autoFDX(3), autoHDX(4), negotiating(5)  


cmefg100LocTpPause 1.3.6.1.4.1.868.2.4.1.2.2.27.1.128
OBJECT-TYPE    
  INTEGER asymmetricRx(1), asymmetricTx(2), symmetric(3), disabled(4)  

cmefg100LocTpQosPause 1.3.6.1.4.1.868.2.4.1.2.2.27.1.129
QOS: Quality of Service
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cmefg100LocTpSacEnable 1.3.6.1.4.1.868.2.4.1.2.2.27.1.130
Enable/disable traps for Source Address Change
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cmefg100LocTpSacStatus 1.3.6.1.4.1.868.2.4.1.2.2.27.1.131
OBJECT-TYPE    
  INTEGER changed(1), constant(2)  

cmefg100LocTpSpeed 1.3.6.1.4.1.868.2.4.1.2.2.27.1.132
Read-only values 3..6 are returned when autonegotiation is enabled
OBJECT-TYPE    
  INTEGER force10Mbps(1), force100Mbps(2), auto10Mbps(3), auto100Mbps(4), auto1000Mbps(5), negotiating(6)  

cmefg100LocTxFxBwaKb 1.3.6.1.4.1.868.2.4.1.2.2.27.1.133
TX to FX bandwidth allocation, in Kbps
OBJECT-TYPE    
  INTEGER 1..122112  

cmefg100LocTxFxBwaMb 1.3.6.1.4.1.868.2.4.1.2.2.27.1.134
TX to FX bandwidth allocation, in Mbps
OBJECT-TYPE    
  INTEGER 1..1000  

cmefg100LocUptime 1.3.6.1.4.1.868.2.4.1.2.2.27.1.135
Write with 0 to reset.
OBJECT-TYPE    
  TimeTicks  

cmefg100QosHqWeight 1.3.6.1.4.1.868.2.4.1.2.2.27.1.136
OBJECT-TYPE    
  INTEGER 0..15  

cmefg100QosLqWeight 1.3.6.1.4.1.868.2.4.1.2.2.27.1.137
OBJECT-TYPE    
  INTEGER 0..15  

cmefg100QosPriority 1.3.6.1.4.1.868.2.4.1.2.2.27.1.138
OBJECT-TYPE    
  INTEGER 0..7  

cmefg100RmtColdStart 1.3.6.1.4.1.868.2.4.1.2.2.27.1.139
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cmefg100RmtDetected 1.3.6.1.4.1.868.2.4.1.2.2.27.1.140
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cmefg100RmtDmiRxPower 1.3.6.1.4.1.868.2.4.1.2.2.27.1.141
OBJECT-TYPE    
  INTEGER  

cmefg100RmtDmiRxPowerAlarm 1.3.6.1.4.1.868.2.4.1.2.2.27.1.142
OBJECT-TYPE    
  INTEGER normal(1), notSupported(2), lowWarn(3), highWarn(4), lowAlarm(5), highAlarm(6)  

cmefg100RmtDmiTemp 1.3.6.1.4.1.868.2.4.1.2.2.27.1.143
In tenths of degrees C
OBJECT-TYPE    
  INTEGER  

cmefg100RmtDmiTempAlarm 1.3.6.1.4.1.868.2.4.1.2.2.27.1.144
OBJECT-TYPE    
  INTEGER normal(1), notSupported(2), lowWarn(3), highWarn(4), lowAlarm(5), highAlarm(6)  

cmefg100RmtDmiTxBiasAlarm 1.3.6.1.4.1.868.2.4.1.2.2.27.1.145
OBJECT-TYPE    
  INTEGER normal(1), notSupported(2), lowWarn(3), highWarn(4), lowAlarm(5), highAlarm(6)  

cmefg100RmtDmiTxBiasCurrent 1.3.6.1.4.1.868.2.4.1.2.2.27.1.146
In microamperes
OBJECT-TYPE    
  INTEGER  

cmefg100RmtDmiTxPower 1.3.6.1.4.1.868.2.4.1.2.2.27.1.147
In microwatts
OBJECT-TYPE    
  INTEGER  

cmefg100RmtDmiTxPowerAlarm 1.3.6.1.4.1.868.2.4.1.2.2.27.1.148
OBJECT-TYPE    
  INTEGER normal(1), notSupported(2), lowWarn(3), highWarn(4), lowAlarm(5), highAlarm(6)  

cmefg100RmtFactoryReset 1.3.6.1.4.1.868.2.4.1.2.2.27.1.149
OBJECT-TYPE    
  INTEGER reset(1), doNothing(2)  

cmefg100RmtFiberAutoNegot 1.3.6.1.4.1.868.2.4.1.2.2.27.1.150
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  


cmefg100RmtFiberPause 1.3.6.1.4.1.868.2.4.1.2.2.27.1.152
OBJECT-TYPE    
  INTEGER asymmetricRx(1), asymmetricTx(2), symmetric(3), notSupported(4)  

cmefg100RmtFiberQosPause 1.3.6.1.4.1.868.2.4.1.2.2.27.1.153
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cmefg100RmtFirmwareRevision 1.3.6.1.4.1.868.2.4.1.2.2.27.1.154
OBJECT-TYPE    
  INTEGER  

cmefg100RmtFpgaRev 1.3.6.1.4.1.868.2.4.1.2.2.27.1.155
Field-Programmable Gate Array revision
OBJECT-TYPE    
  INTEGER  

cmefg100RmtOamActiveMode 1.3.6.1.4.1.868.2.4.1.2.2.27.1.156
OBJECT-TYPE    
  INTEGER active(1), passive(2)  

cmefg100RmtOamCriticalEvent 1.3.6.1.4.1.868.2.4.1.2.2.27.1.157
OBJECT-TYPE    
  INTEGER critical(1), normal(2)  

cmefg100RmtOamLastGasp 1.3.6.1.4.1.868.2.4.1.2.2.27.1.158
OBJECT-TYPE    
  INTEGER failure(1), normal(2)  

cmefg100RmtOamLinkEvents 1.3.6.1.4.1.868.2.4.1.2.2.27.1.159
OBJECT-TYPE    
  INTEGER supported(1), notSupported(2)  

cmefg100RmtOamLinkFault 1.3.6.1.4.1.868.2.4.1.2.2.27.1.160
OBJECT-TYPE    
  INTEGER fault(1), normal(2)  

cmefg100RmtOamLocDteDisc 1.3.6.1.4.1.868.2.4.1.2.2.27.1.161
OBJECT-TYPE    
  INTEGER completed(1), notCompleted(2), unsatisfied(3)  

cmefg100RmtOamPeerConfigRevision 1.3.6.1.4.1.868.2.4.1.2.2.27.1.162
OBJECT-TYPE    
  INTEGER  

cmefg100RmtOamPeerMacAddress 1.3.6.1.4.1.868.2.4.1.2.2.27.1.163
OBJECT-TYPE    
  MacAddress  

cmefg100RmtOamPeerMaxOamPduSize 1.3.6.1.4.1.868.2.4.1.2.2.27.1.164
OBJECT-TYPE    
  INTEGER  

cmefg100RmtOamPeerMultiplexorState 1.3.6.1.4.1.868.2.4.1.2.2.27.1.165
OBJECT-TYPE    
  INTEGER forwarding(1), discarding(2)  

cmefg100RmtOamPeerParserState 1.3.6.1.4.1.868.2.4.1.2.2.27.1.166
OBJECT-TYPE    
  INTEGER forwarding(1), discarding(2), looping(3)  

cmefg100RmtOamPeerVendorInfo 1.3.6.1.4.1.868.2.4.1.2.2.27.1.167
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

cmefg100RmtOamPeerVendorOui 1.3.6.1.4.1.868.2.4.1.2.2.27.1.168
OBJECT-TYPE    
  OCTET STRING SIZE(3)  

cmefg100RmtOamRmtDteDisc 1.3.6.1.4.1.868.2.4.1.2.2.27.1.169
OBJECT-TYPE    
  INTEGER completed(1), notCompleted(2), unsatisfied(3)  

cmefg100RmtOamRmtLoopback 1.3.6.1.4.1.868.2.4.1.2.2.27.1.170
Initiates remote loopback mode if the remote supports it. See RmtOamPeerParserState for status information
OBJECT-TYPE    
  INTEGER enabledOam(1), enabledAlternate(2), disabled(3), notSupported(4)  

cmefg100RmtOamUnidirectional 1.3.6.1.4.1.868.2.4.1.2.2.27.1.171
OBJECT-TYPE    
  INTEGER supported(1), notSupported(2)  

cmefg100RmtOamVarRetrieval 1.3.6.1.4.1.868.2.4.1.2.2.27.1.172
OBJECT-TYPE    
  INTEGER supported(1), notSupported(2)  

cmefg100RmtSelfTestFailed 1.3.6.1.4.1.868.2.4.1.2.2.27.1.173
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cmefg100RmtSerialNumber 1.3.6.1.4.1.868.2.4.1.2.2.27.1.174
OBJECT-TYPE    
  INTEGER  

cmefg100RmtTpAdv1000FDX 1.3.6.1.4.1.868.2.4.1.2.2.27.1.175
Read-only value notApplicable returned when autonegotiation is disabled
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cmefg100RmtTpAdv1000HDX 1.3.6.1.4.1.868.2.4.1.2.2.27.1.176
Read-only value notApplicable returned when autonegotiation is disabled
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cmefg100RmtTpAdv100FDX 1.3.6.1.4.1.868.2.4.1.2.2.27.1.177
Read-only value notApplicable returned when autonegotiation is disabled
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cmefg100RmtTpAdv100HDX 1.3.6.1.4.1.868.2.4.1.2.2.27.1.178
Read-only value notApplicable returned when autonegotiation is disabled
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cmefg100RmtTpAdv10FDX 1.3.6.1.4.1.868.2.4.1.2.2.27.1.179
Read-only value notApplicable returned when autonegotiation is disabled
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cmefg100RmtTpAdv10HDX 1.3.6.1.4.1.868.2.4.1.2.2.27.1.180
Read-only value notApplicable returned when autonegotiation is disabled
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

cmefg100RmtTpAutoNegot 1.3.6.1.4.1.868.2.4.1.2.2.27.1.181
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cmefg100RmtTpCross 1.3.6.1.4.1.868.2.4.1.2.2.27.1.182
OBJECT-TYPE    
  INTEGER forceMDI(1), forceMDI-X(2), auto(3)  

cmefg100RmtTpDuplex 1.3.6.1.4.1.868.2.4.1.2.2.27.1.183
Read-only values 3..5 are returned when autonegotiation is enabled
OBJECT-TYPE    
  INTEGER forceFDX(1), forceHDX(2), autoFDX(3), autoHDX(4), negotiating(5)  


cmefg100RmtTpPause 1.3.6.1.4.1.868.2.4.1.2.2.27.1.185
OBJECT-TYPE    
  INTEGER asymmetricRx(1), asymmetricTx(2), symmetric(3), notSupported(4)  

cmefg100RmtTpQosPause 1.3.6.1.4.1.868.2.4.1.2.2.27.1.186
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cmefg100RmtTpSpeed 1.3.6.1.4.1.868.2.4.1.2.2.27.1.187
Read-only values 3..6 are returned when autonegotiation is enabled
OBJECT-TYPE    
  INTEGER force10Mbps(1), force100Mbps(2), auto10Mbps(3), auto100Mbps(4), auto1000Mbps(5), negotiating(6)  

cmefg100RmtUptime 1.3.6.1.4.1.868.2.4.1.2.2.27.1.188
Write with 0 to reset.
OBJECT-TYPE    
  TimeTicks  

cmefg100VlanCacheCmd 1.3.6.1.4.1.868.2.4.1.2.2.27.1.189
All variables starting with cmefg100Lad relate to 802.1Q VLAN controls. Setting this var to loadCache commands the agent to upload the VLAN table from the device exactly one time. Note that the contents of this cache are NOT automatically refreshed. A genErr will be returned if any other command involving reading or writing the LAD or the VLAN table is in progress.
OBJECT-TYPE    
  INTEGER loadCache(1), doNothing(2), release(3)  

cmefg100VlanCacheState 1.3.6.1.4.1.868.2.4.1.2.2.27.1.190
The agent discards the VLAN table shortly after uploading it to prevent the reporting of outdated information. This variable shows the current state of the cache. If it reads 'empty,' set VlanCacheCmd to loadCache to upload the VLAN table.
OBJECT-TYPE    
  INTEGER ready(1), empty(2), transferring(3), bufferBusy(4)  

cmefg100VlanEditCmd 1.3.6.1.4.1.868.2.4.1.2.2.27.1.191
Setting this var to write causes VlanEditFwdFiber, VlanEditFwdTp, VlanEditUntagFiber, VlanEditUntagTp, and VlanEditVid to be written to the VLAN tablei (i.e. insert/overwrite). Setting this var to delete causes the VLAN Id represented by VlanEditVlanId to be deleted from the VLAN table. A genErr will be returned if any other command involving reading or writing the LAD or the VLAN table is in progress.
OBJECT-TYPE    
  INTEGER write(1), delete(2), doNothing(3)  

cmefg100VlanEditFwdFiber 1.3.6.1.4.1.868.2.4.1.2.2.27.1.192
A fiber egress rule to be acted upon by VlanEditCmd
OBJECT-TYPE    
  INTEGER drop(1), forward(2)  

cmefg100VlanEditFwdTp 1.3.6.1.4.1.868.2.4.1.2.2.27.1.193
A twisted pair egress rule to be acted upon by VlanEditCmd
OBJECT-TYPE    
  INTEGER drop(1), forward(2)  

cmefg100VlanEditUntagFiber 1.3.6.1.4.1.868.2.4.1.2.2.27.1.194
A fiber untag rule to be acted upon by VlanEditCmd
OBJECT-TYPE    
  INTEGER untag(1), asIs(2)  

cmefg100VlanEditUntagTp 1.3.6.1.4.1.868.2.4.1.2.2.27.1.195
A twisted pair untag rule to be acted upon by VlanEditCmd
OBJECT-TYPE    
  INTEGER untag(1), asIs(2)  

cmefg100VlanEditVid 1.3.6.1.4.1.868.2.4.1.2.2.27.1.196
A VLAN Id to be acted upon by VlanEditCmd
OBJECT-TYPE    
  INTEGER  

cmefg100VlanEnable 1.3.6.1.4.1.868.2.4.1.2.2.27.1.197
Enable/disable for 802.1Q VLAN tag processing.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cmefg100VlanEntries 1.3.6.1.4.1.868.2.4.1.2.2.27.1.198
A count of the number of entries currently in the VLAN table cache. See also VlanCacheState. If a VLAN cache-filling transfer is in progress, this variable can be read for a progress report.
OBJECT-TYPE    
  INTEGER  

cmefg100VlanFiberDefaultPri 1.3.6.1.4.1.868.2.4.1.2.2.27.1.199
OBJECT-TYPE    
  INTEGER 0..7  

cmefg100VlanFiberDefaultVid 1.3.6.1.4.1.868.2.4.1.2.2.27.1.200
OBJECT-TYPE    
  INTEGER 0..4095  

cmefg100VlanFiberInUntaggedDrop 1.3.6.1.4.1.868.2.4.1.2.2.27.1.201
OBJECT-TYPE    
  INTEGER drop(1), forward(2), notApplicable(3)  

cmefg100VlanFwdFiberTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.202
Indicates whether packets with the VLAN Id specified by the corresponding cmefg100VlanVidTbl entry (i.e. the one with the same SubDeviceIndex) are forwarded or dropped when they are routed for fiber egress. The SubDeviceIndex is an arbitrary integer sequence number, range 1..cmefg100VlanEntries.
OBJECT-TYPE    
  INTEGER drop(1), forward(2)  

cmefg100VlanFwdTpTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.203
Indicates whether packets with the VLAN Id specified by the corresponding cmefg100VlanVidTbl entry (i.e. the one with the same SubDeviceIndex) are forwarded or dropped when they are routed for twisted pair egress. The SubDeviceIndex is an arbitrary integer sequence number, range 1..cmefg100VlanEntries.
OBJECT-TYPE    
  INTEGER drop(1), forward(2)  

cmefg100VlanIngressVidHitNoMem 1.3.6.1.4.1.868.2.4.1.2.2.27.1.204
Ingress violation - port from which frame originates is not a member of the VLAN indicated by the frame's tag
OBJECT-TYPE    
  INTEGER forward(1), drop(2), learn(3)  

cmefg100VlanIngressVidMiss 1.3.6.1.4.1.868.2.4.1.2.2.27.1.205
Ingress violation - the VLAN indicated by the frame's tag is undefined in the VLAN table.
OBJECT-TYPE    
  INTEGER flood(1), drop(2)  

cmefg100VlanPriMapTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.206
A table containing new priority values for priority remapping. The SubDeviceIndex is 'original priority', range 0..7.
OBJECT-TYPE    
  INTEGER 0..7  

cmefg100VlanPriTagCtrl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.207
OBJECT-TYPE    
  INTEGER asIs(1), remapPriority(2), remapVid(3), remapBoth(4), notApplicable(5)  

cmefg100VlanSetFailed 1.3.6.1.4.1.868.2.4.1.2.2.27.1.208
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cmefg100VlanTagIn 1.3.6.1.4.1.868.2.4.1.2.2.27.1.209
OBJECT-TYPE    
  INTEGER tag(1), noTag(2), notApplicable(3)  

cmefg100VlanTpDefaultPri 1.3.6.1.4.1.868.2.4.1.2.2.27.1.210
OBJECT-TYPE    
  INTEGER 0..7  

cmefg100VlanTpDefaultVid 1.3.6.1.4.1.868.2.4.1.2.2.27.1.211
OBJECT-TYPE    
  INTEGER 0..4095  

cmefg100VlanTpInUntaggedDrop 1.3.6.1.4.1.868.2.4.1.2.2.27.1.212
OBJECT-TYPE    
  INTEGER drop(1), forward(2)  

cmefg100VlanUntagFiberTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.213
Indicates whether VLAN Ids are stripped from packets with the VLAN Id specified by the corresponding cmefg100VlanVidTbl entry (i.e. the one with the same SubDeviceIndex) when they are routed for fiber egress. The SubDeviceIndex is an arbitrary integer sequence number, range 1..cmefg100VlanEntries.
OBJECT-TYPE    
  INTEGER untag(1), asIs(2)  

cmefg100VlanUntagTpTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.214
Indicates whether VLAN Ids are stripped from packets with the VLAN Id specified by the corresponding cmefg100VlanVidTbl entry (i.e. the one with the same SubDeviceIndex) when they are routed for twisted pair egress. The SubDeviceIndex is an arbitrary integer sequence number, range 1..cmefg100VlanEntries.
OBJECT-TYPE    
  INTEGER untag(1), asIs(2)  

cmefg100VlanVidTagCtrl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.215
OBJECT-TYPE    
  INTEGER asIs(1), remapPriority(2), remapVid(3), remapBoth(4), notApplicable(5)  

cmefg100VlanVidTbl 1.3.6.1.4.1.868.2.4.1.2.2.27.1.216
The SubDeviceIndex is an arbitrary integer sequence number, range 1..cmefg100VlanEntries.
OBJECT-TYPE    
  INTEGER  

cmefg100CacheClean 1.3.6.1.4.1.868.2.4.1.2.2.27.1.217
And all of the MIB variables lived happily ever after. The End.
OBJECT-TYPE    
  INTEGER  

backplane 1.3.6.1.4.1.868.2.4.2
OBJECT IDENTIFIER    

mcc16 1.3.6.1.4.1.868.2.4.2.1
OBJECT IDENTIFIER    

mcc16Common 1.3.6.1.4.1.868.2.4.2.1.1
OBJECT IDENTIFIER    

mcc16ComHwReset 1.3.6.1.4.1.868.2.4.2.1.1.1
Save configuration to FLASH and perform a hardware reset
OBJECT-TYPE    
  INTEGER noReset(1), reset(2)  

mcc16ComMgmtHwRev 1.3.6.1.4.1.868.2.4.2.1.1.2
The management h/w board revision.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

mcc16ComMgmtSwRev 1.3.6.1.4.1.868.2.4.2.1.1.3
The downloadable management s/w code revision.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

mcc16ComIpAddr 1.3.6.1.4.1.868.2.4.2.1.1.4
The IP address of the management interface.
OBJECT-TYPE    
  IpAddress  

mcc16ComNetMask 1.3.6.1.4.1.868.2.4.2.1.1.5
The subnet mask associated with the IP address of the management interface. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
OBJECT-TYPE    
  IpAddress  

mcc16ComGateway 1.3.6.1.4.1.868.2.4.2.1.1.6
The managment interface's default gateway.
OBJECT-TYPE    
  IpAddress  

mcc16ComPS1Power 1.3.6.1.4.1.868.2.4.2.1.1.7
On if power supply 1 is installed and powered
OBJECT-TYPE    
  INTEGER on(1), off(2)  

mcc16ComPS1InUse 1.3.6.1.4.1.868.2.4.2.1.1.8
On if power supply 1 is currently active
OBJECT-TYPE    
  INTEGER on(1), off(2)  

mcc16ComPS2Power 1.3.6.1.4.1.868.2.4.2.1.1.9
On if power supply 2 is installed and powered
OBJECT-TYPE    
  INTEGER on(1), off(2)  

mcc16ComPS2InUse 1.3.6.1.4.1.868.2.4.2.1.1.10
On if power supply 2 is currently active
OBJECT-TYPE    
  INTEGER on(1), off(2)  

mcc16ComNotes 1.3.6.1.4.1.868.2.4.2.1.1.11
Enduser-defined text notes
OBJECT-TYPE    
  DisplayString SIZE(0..4096)  

mcc16Ver1 1.3.6.1.4.1.868.2.4.2.1.2
OBJECT IDENTIFIER    

mcc16SlotTable 1.3.6.1.4.1.868.2.4.2.1.2.1
One table entry per slot in the media converter chassis. Value of entry is type of device in the slot, or a value indicating that the slot is empty.
OBJECT-TYPE    
  SEQUENCE OF  
    Mcc16SlotEntry

mcc16SlotEntry 1.3.6.1.4.1.868.2.4.2.1.2.1.1
The type of device inserted in a single chassis slot
OBJECT-TYPE    
  Mcc16SlotEntry  

mcc16Index 1.3.6.1.4.1.868.2.4.2.1.2.1.1.1
The index of a slot in a media converter chassis
OBJECT-TYPE    
  INTEGER 1..16  

mcc16DeviceType 1.3.6.1.4.1.868.2.4.2.1.2.1.1.2
The object ID of the device in the a slot
OBJECT-TYPE    
  OBJECT IDENTIFIER  

cps 1.3.6.1.4.1.868.2.4.2.2
OBJECT IDENTIFIER    

cpsCabSummary 1.3.6.1.4.1.868.2.4.2.2.1
OBJECT IDENTIFIER    

cpsCabinetTable 1.3.6.1.4.1.868.2.4.2.2.1.1
Sparse table containing one entry for each Cabinet in the stack, indexed by cabinet serial number.
OBJECT-TYPE    
  SEQUENCE OF  
    CpsCabinetEntry

cpsCabinetEntry 1.3.6.1.4.1.868.2.4.2.2.1.1.1
Status and Configuration entries for a single Cabinet.
OBJECT-TYPE    
  CpsCabinetEntry  

cpsCabinetBiaIndex 1.3.6.1.4.1.868.2.4.2.2.1.1.1.1
The serial number (BIA) of the Cabinet
OBJECT-TYPE    
  INTEGER  

cpsCabinetModel 1.3.6.1.4.1.868.2.4.2.2.1.1.1.2
The model number of the cabinet
OBJECT-TYPE    
  OBJECT IDENTIFIER  

cpsCabinetDescription 1.3.6.1.4.1.868.2.4.2.2.1.1.1.3
User defined text description of the cabinet. This description is a mirror of the ones that can be found under cpsCabDetail.
OBJECT-TYPE    
  DisplayString  

cpsCabinetSequence 1.3.6.1.4.1.868.2.4.2.2.1.1.1.4
An arbitrary sequence number assigned to the cabinet by the agent for the use of the Focal Point application. Cabinets are sorted by BiaIndex in the table, and numbered sequentially.
OBJECT-TYPE    
  INTEGER  

cpsCabDetail 1.3.6.1.4.1.868.2.4.2.2.2
OBJECT IDENTIFIER    

cpsMc1800Table 1.3.6.1.4.1.868.2.4.2.2.2.1
Sparse table containing one entry for each CPSMC1800 in the stack, indexed by cabinet serial number.
OBJECT-TYPE    
  SEQUENCE OF  
    CpsMc1800Entry

cpsMc1800Entry 1.3.6.1.4.1.868.2.4.2.2.2.1.1
Status and configuration entries for a single CPSMC1800
OBJECT-TYPE    
  CpsMc1800Entry  

cpsMc1800BiaIndex 1.3.6.1.4.1.868.2.4.2.2.2.1.1.1
The serial number (BIA) of the cabinet
OBJECT-TYPE    
  INTEGER  

cpsMc1800Description 1.3.6.1.4.1.868.2.4.2.2.2.1.1.2
User defined text description of the cabinet. A mirror of cpsCabinetDescription.
OBJECT-TYPE    
  DisplayString  

cpsMc1800PSPower1 1.3.6.1.4.1.868.2.4.2.2.2.1.1.3
Power status, first power supply slot. Value is on(1) when the supply is capable of supplying power.
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cpsMc1800PSInUse1 1.3.6.1.4.1.868.2.4.2.2.2.1.1.4
Power status, first power supply slot. Value is yes(1) when the power is selected to supply power to the cabinet
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsMc1800PSPower2 1.3.6.1.4.1.868.2.4.2.2.2.1.1.5
Power status, second power supply slot. Value is on(1) when the supply is capable of supplying power.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsMc1800PSInUse2 1.3.6.1.4.1.868.2.4.2.2.2.1.1.6
Power status, second power supply slot. Value is yes(1) when the power is selected to supply power to the cabinet
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsMc1800MRevision 1.3.6.1.4.1.868.2.4.2.2.2.1.1.7
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cpsMc1300Table 1.3.6.1.4.1.868.2.4.2.2.2.2
Sparse table containing one entry for each CPSMC1300 in the stack, indexed by cabinet serial number.
OBJECT-TYPE    
  SEQUENCE OF  
    CpsMc1300Entry

cpsMc1300Entry 1.3.6.1.4.1.868.2.4.2.2.2.2.1
Status and configuration entries for a single CPSMC1300
OBJECT-TYPE    
  CpsMc1300Entry  

cpsMc1300BiaIndex 1.3.6.1.4.1.868.2.4.2.2.2.2.1.1
The serial number (BIA) of the cabinet
OBJECT-TYPE    
  INTEGER  

cpsMc1300Description 1.3.6.1.4.1.868.2.4.2.2.2.2.1.2
User defined text description of the cabinet. A mirror of cpsCabinetDescription.
OBJECT-TYPE    
  DisplayString  

cpsMc1300PSPower1 1.3.6.1.4.1.868.2.4.2.2.2.2.1.3
Power status, first power supply slot. Value is on(1) when the supply is capable of supplying power.
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cpsMc1300PSInUse1 1.3.6.1.4.1.868.2.4.2.2.2.2.1.4
For future expansion. At the time of this writing, the CPSMC1300 did not accept any power supplies capable of supporting a master/slave relationship, meaning that all 'ready' power supplies share load and therefore are 'in use'. If master/slave support were present, inuse would indicate whether or not this supply was currently supplying power to the cabinet.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsMc1300PSPower2 1.3.6.1.4.1.868.2.4.2.2.2.2.1.5
Power status, second power supply slot. Value is on(1) when the supply is capable of supplying power.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsMc1300PSInUse2 1.3.6.1.4.1.868.2.4.2.2.2.2.1.6
For future expansion. At the time of this writing, the CPSMC1300 did not accept any power supplies capable of supporting a master/slave relationship, meaning that all 'ready' power supplies share load and therefore are 'in use'. If master/slave support were present, inuse would indicate whether or not this supply was currently supplying power to the cabinet.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

cpsMc1300MRevision 1.3.6.1.4.1.868.2.4.2.2.2.2.1.7
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cpsMc0200Table 1.3.6.1.4.1.868.2.4.2.2.2.3
Sparse table containing one entry for each CPSMC0200 in the stack, indexed by cabinet serial number.
OBJECT-TYPE    
  SEQUENCE OF  
    CpsMc0200Entry

cpsMc0200Entry 1.3.6.1.4.1.868.2.4.2.2.2.3.1
Status and configuration entries for a single CPSMC0200
OBJECT-TYPE    
  CpsMc0200Entry  

cpsMc0200BiaIndex 1.3.6.1.4.1.868.2.4.2.2.2.3.1.1
The serial number (BIA) of the cabinet
OBJECT-TYPE    
  INTEGER  

cpsMc0200Description 1.3.6.1.4.1.868.2.4.2.2.2.3.1.2
User defined text description of the cabinet. A mirror of cpsCabinetDescription.
OBJECT-TYPE    
  DisplayString  

cpsMc0200MRevision 1.3.6.1.4.1.868.2.4.2.2.2.3.1.3
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cpsMc1900Table 1.3.6.1.4.1.868.2.4.2.2.2.4
Sparse table containing one entry for each CPSMC1900 in the stack, indexed by cabinet serial number.
OBJECT-TYPE    
  SEQUENCE OF  
    CpsMc1900Entry

cpsMc1900Entry 1.3.6.1.4.1.868.2.4.2.2.2.4.1
Status and configuration entries for a single CPSMC1900
OBJECT-TYPE    
  CpsMc1900Entry  

cpsMc1900BiaIndex 1.3.6.1.4.1.868.2.4.2.2.2.4.1.1
The serial number (BIA) of the cabinet
OBJECT-TYPE    
  INTEGER  

cpsMc1900Description 1.3.6.1.4.1.868.2.4.2.2.2.4.1.2
User defined text description of the cabinet. A mirror of cpsCabinetDescription.
OBJECT-TYPE    
  DisplayString  

cpsMc1900MRevision 1.3.6.1.4.1.868.2.4.2.2.2.4.1.3
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

smacf100Table 1.3.6.1.4.1.868.2.4.2.2.2.5
Sparse table containing one entry for each SMACF100 in the stack, indexed by cabinet serial number.
OBJECT-TYPE    
  SEQUENCE OF  
    Smacf100Entry

smacf100Entry 1.3.6.1.4.1.868.2.4.2.2.2.5.1
Status and configuration entries for a single SMACF100
OBJECT-TYPE    
  Smacf100Entry  

smacf100BiaIndex 1.3.6.1.4.1.868.2.4.2.2.2.5.1.1
The serial number (BIA) of the cabinet
OBJECT-TYPE    
  INTEGER  

smacf100Description 1.3.6.1.4.1.868.2.4.2.2.2.5.1.2
User defined text description of the cabinet. A mirror of cpsCabinetDescription.
OBJECT-TYPE    
  DisplayString  

smacf100MRevision 1.3.6.1.4.1.868.2.4.2.2.2.5.1.3
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

smacf100SpanningTree 1.3.6.1.4.1.868.2.4.2.2.2.5.1.4
This variable allows the agent to enable or disable Spanning Tree if it is supported. Not all versions of the hardware support Spanning Tree.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

smacf100ResetCounters 1.3.6.1.4.1.868.2.4.2.2.2.5.1.5
When this variable is set to reset(1), all counters for all ports are reset to zero.
OBJECT-TYPE    
  INTEGER reset(1), doNothing(2)  

smacf100SelfTest 1.3.6.1.4.1.868.2.4.2.2.2.5.1.6
When this variable is set to selfTest(1), the cabinet will perform a self test.
OBJECT-TYPE    
  INTEGER selfTest(1), doNothing(2)  

smacf100QosEnable 1.3.6.1.4.1.868.2.4.2.2.2.5.1.7
This variable allows Quality of Service functions to be enabled or disabled. This includes the processing of 802.1p tags (See smacf100QosHPThreshold(8), smacf100QosLqWeight(9), and smacf100QosHqWeight(10)), half-duplex back pressure and full-duplex flow control. (See smacf100PQosPause(63)). Port priority functionality (smacf100PQosPriority(62)) is always enabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notSupported(3)  

smacf100QosHPThreshold 1.3.6.1.4.1.868.2.4.2.2.2.5.1.8
When an incoming 802.1p priority tag value is greater than or equal to this value (from 0 to 7), the incoming packet will be classified as high-priority. Ignored when smacf100QosEnable(7) is set to 'disabled(2)'.
OBJECT-TYPE    
  INTEGER  

smacf100QosLqWeight 1.3.6.1.4.1.868.2.4.2.2.2.5.1.9
A value between 1 and 15 indicating the number of packets that should be processed from the low-priority queue before attention is turned to the high-priority queue. Ignored when smacf100QosEnable(7) is set to 'disabled(2)'.
OBJECT-TYPE    
  INTEGER  

smacf100QosHqWeight 1.3.6.1.4.1.868.2.4.2.2.2.5.1.10
A value between 1 and 15 indicating the number of packets that should be processed from the high-priority queue before attention is turned to the low-priority queue. Ignored when smacf100QosEnable(7) is set to 'disabled(2)'.
OBJECT-TYPE    
  INTEGER  

smacf100SNMPModuleInstalled 1.3.6.1.4.1.868.2.4.2.2.2.5.1.11
When this variable is set to yes(1), a management module is installed in this particular SMACF100 cabinet.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

smacf100AgingTimer 1.3.6.1.4.1.868.2.4.2.2.2.5.1.12
This configuration varible allows the MAC address aging timer to be adjusted. When an automatically discovered MAC address has not been heard from (i.e. no packets with this source address have been received) for longer than the time specified by this variable, it is deleted from the SMACF100's address cache. The time is specified in seconds (up to 1,048,575). If smacf100AgingTimer(12) is set to 0, MAC address aging is disabled.
OBJECT-TYPE    
  INTEGER  

cpsMc0800Table 1.3.6.1.4.1.868.2.4.2.2.2.6
Sparse table containing one entry for each CPSMC0800 in the stack, indexed by cabinet serial number.
OBJECT-TYPE    
  SEQUENCE OF  
    CpsMc0800Entry

cpsMc0800Entry 1.3.6.1.4.1.868.2.4.2.2.2.6.1
Status and configuration entries for a single CPSMC0800
OBJECT-TYPE    
  CpsMc0800Entry  

cpsMc0800BiaIndex 1.3.6.1.4.1.868.2.4.2.2.2.6.1.1
The serial number (BIA) of the cabinet
OBJECT-TYPE    
  INTEGER  

cpsMc0800Description 1.3.6.1.4.1.868.2.4.2.2.2.6.1.2
User defined text description of the cabinet. A mirror of cpsCabinetDescription.
OBJECT-TYPE    
  DisplayString  

cpsMc0800MRevision 1.3.6.1.4.1.868.2.4.2.2.2.6.1.3
The marketing revision of this device
OBJECT-TYPE    
  INTEGER  

cpsAgent 1.3.6.1.4.1.868.2.4.2.2.3
OBJECT IDENTIFIER    

cpsGroupCtrl 1.3.6.1.4.1.868.2.4.2.2.3.1
This string is used to select one or more groups of devices to receive mass configuration operations. When cpsGroupCtrl.0 is null, SNMP operations are performed in the standard way for SNMPv1. When cpsGroupCtrl.0 is not null, the Cabinet (BiaIndex) and Slot (SlotIndex) index values that uniquely identify a device are ignored, and instead the operation is applied to all devices that have Groups variables that contain user- or system-defined keywords that match those in cpsGroupCtrl.0. The CfgMatch variables (cpsSlotDetail) for each of these devices will be yes(1). Advanced options are invoked by prepending one of the following command characters to the keywords in cpsGroupCtrl.0: 1) '.' means 'Pick-One'. When any 'Pick-One' operators are present in the Group Control String, then one or more of the keywords so marked must appear in the Device Group String of the slide-in device for configuration changes to be allowed. 'Pick-One' is the default operation that is used when no command character is present on a keyword. 2) '-' or '!' means 'Prohibited'. When any 'Prohibited' operators are present in the Group Control String, then if any of the keywords so marked appears in the Device Group String of the slide-in device, then no configuration changes are applied. 3) '+' is the 'Required' operator. When any 'Required' operators are present in the Group Control String, then all of the keywords so marked must appear in the Device Group String of the slide-in device for configuration changes to be allowed. 4) '*' is a Wildcard that matches zero or more characters. It is the only command character that does not need to appear at the beginning of the keyword. It is also the only one that can be used in combination with the others within a single keyword.
OBJECT-TYPE    
  DisplayString SIZE(0..256)  

cpsSlotPwrTable 1.3.6.1.4.1.868.2.4.2.2.3.2
Sparse table containing one power control entry for each slot in the stack, indexed by cabinet serial number and slot.
OBJECT-TYPE    
  SEQUENCE OF  
    CpsSlotPwrEntry

cpsSlotPwrEntry 1.3.6.1.4.1.868.2.4.2.2.3.2.1
The power on/off control for a single Point System slot.
OBJECT-TYPE    
  CpsSlotPwrEntry  

cpsSlotPwrBiaIndex 1.3.6.1.4.1.868.2.4.2.2.3.2.1.1
The cabinet serial number (BIA) of the slot
OBJECT-TYPE    
  INTEGER  

cpsSlotPwrSlotIndex 1.3.6.1.4.1.868.2.4.2.2.3.2.1.2
The slot number of the slot
OBJECT-TYPE    
  INTEGER  

cpsSlotPwrState 1.3.6.1.4.1.868.2.4.2.2.3.2.1.3
The power control for the slot. When off(2), no power is supplied to the slot. If examined, the slot will appear empty.
OBJECT-TYPE    
  INTEGER on(1), off(2)  

cpsIsPrimary 1.3.6.1.4.1.868.2.4.2.2.3.3
Indicates whether or not this Management Module is the primary Management Module in the stack. This variable contains the same information as the cpsmm100IsPrimary variable, but answers a slightly different question: cpsmm100IsPrimary answers 'what is the primary status of the management module in cabinet C slot S?' and cpsIsPrimary answers 'what is the primary status of the management module I am talking to now?' The difference is that cpsIsPrimary does not require that the requestor translate the IP address of the management module they are communicating with into a cabinet serial number (BIA) and slot index. This could otherwise only be accomplished via a sequential search through cpsmm100Table
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

Defined Objects

MacAddress  
OCTET STRING SIZE(6)    

CpsConnector  
INTEGER rj-45(10), stmm(11), stsm(12), scmm(13), scsm(14), scsmlh(15), scsmelh(16), scsmlhlw(17), mtrjmm(18), lc(19), bnc(20), stsmlh(21), stsmelh(22), scmm1300(23), stmm1300(24), mtrjsm(25), serial26(26), stmmlh(27), scsmsh(28), scsimplex(29), bncdual(30), db9rsxxx(31), termblock(32), rj11(33), sc40km(34), sc125km(35)    

CeTbtFrl03Entry  
SEQUENCE    
  INTEGER as ceTbtFrl03Index  
  INTEGER as ceTbtFrl03FiberRecv  
  INTEGER as ceTbtFrl03FiberLink  
  INTEGER as ceTbtFrl03TPRecv  
  INTEGER as ceTbtFrl03TPLink  
  INTEGER as ceTbtFrl03Power  

CeCxTbt04Entry  
SEQUENCE    
  INTEGER as ceCxTbt04Index  
  INTEGER as ceCxTbt04Jabber  
  INTEGER as ceCxTbt04CoaxRecv  
  INTEGER as ceCxTbt04TPRecv  
  INTEGER as ceCxTbt04TPLink  
  INTEGER as ceCxTbt04Power  

CeCxFrl04Entry  
SEQUENCE    
  INTEGER as ceCxFrl04Index  
  INTEGER as ceCxFrl04Jabber  
  INTEGER as ceCxFrl04CoaxRecv  
  INTEGER as ceCxFrl04FLRecv  
  INTEGER as ceCxFrl04FLLink  
  INTEGER as ceCxFrl04Power  

CfSmMm02Entry  
SEQUENCE    
  INTEGER as cfSmMm02Index  
  INTEGER as cfSmMm02MMSignalDetect  
  INTEGER as cfSmMm02SMSignalDetect  
  INTEGER as cfSmMm02Power  

CfSmMm05Entry  
SEQUENCE    
  INTEGER as cfSmMm05Index  
  INTEGER as cfSmMm05SMSignalDetect  
  INTEGER as cfSmMm05MMSignalDetect  
  INTEGER as cfSmMm05Power  

CaCf02Entry  
SEQUENCE    
  INTEGER as caCf02Index  
  INTEGER as caCf02CopperSignalDetect  
  INTEGER as caCf02FiberSignalDetect  
  INTEGER as caCf02Power  

CfSmMm06Entry  
SEQUENCE    
  INTEGER as cfSmMm06Index  
  INTEGER as cfSmMm06MMSignalDetect  
  INTEGER as cfSmMm06SMSignalDetect  
  INTEGER as cfSmMm06Power  

Ct1e1Cf01Entry  
SEQUENCE    
  INTEGER as ct1e1Cf01Index  
  INTEGER as ct1e1Cf01CopperSignalDetect  
  INTEGER as ct1e1Cf01FiberSignalDetect  
  INTEGER as ct1e1Cf01CoaxActive  

CeRTxFx01Entry  
SEQUENCE    
  INTEGER as ceRTxFx01Index  
  INTEGER as ceRTxFx01TPPrimary  
  INTEGER as ceRTxFx01FiberPrimary  
  INTEGER as ceRTxFx01TPSignalDetect  
  INTEGER as ceRTxFx01FiberSignalDetect  

Ce100BtxFx04Entry  
SEQUENCE    
  INTEGER as ce100BtxFx04Index  
  INTEGER as ce100BtxFx04TPRecv  
  INTEGER as ce100BtxFx04FiberRecv  
  INTEGER as ce100BtxFx04TPSignalDetect  
  INTEGER as ce100BtxFx04FiberSignalDetect  
  INTEGER as ce100BtxFx04Power  

CpsCf01Entry  
SEQUENCE    
  INTEGER as cpsCf01Index  
  INTEGER as cpsCf01FiberRecv  
  INTEGER as cpsCf01TPRecv  
  INTEGER as cpsCf01Power  

CbCf01Entry  
SEQUENCE    
  INTEGER as cbCf01Index  
  INTEGER as cbCf01FiberRecv  
  INTEGER as cbCf01TPCoaxRecv  
  INTEGER as cbCf01Power  

CarCf01Entry  
SEQUENCE    
  INTEGER as carCf01Index  
  INTEGER as carCf01FiberRecv  
  INTEGER as carCf01TPRecv  
  INTEGER as carCf01Power  

CarCf02Entry  
SEQUENCE    
  INTEGER as carCf02Index  
  INTEGER as carCf02FiberRecv  
  INTEGER as carCf02CoaxRecv  
  INTEGER as carCf02Power  

CePswFx03Entry  
SEQUENCE    
  INTEGER as cePswFx03Index  
  INTEGER as cePswFx03TPFullDuplex  
  INTEGER as cePswFx03FiberFullDuplex  
  INTEGER as cePswFx03TPLink  
  INTEGER as cePswFx03FiberLink  
  INTEGER as cePswFx03TP100Mbps  

CePswSx01Entry  
SEQUENCE    
  INTEGER as cePswSx01Index  
  INTEGER as cePswSx01TPFullDuplex  
  INTEGER as cePswSx01FiberFullDuplex  
  INTEGER as cePswSx01TPLink  
  INTEGER as cePswSx01FiberLink  
  INTEGER as cePswSx01TP100Mbps  

CRs232Cf01Entry  
SEQUENCE    
  INTEGER as cRs232Cf01Index  
  INTEGER as cRs232Cf01FiberLock  

CfSmMm04Entry  
SEQUENCE    
  INTEGER as cfSmMm04Index  
  INTEGER as cfSmMm04MMSignalDetect  
  INTEGER as cfSmMm04SMSignalDetect  
  INTEGER as cfSmMm04Power  

Ce100BtxSx01Entry  
SEQUENCE    
  INTEGER as ce100BtxSx01Index  
  INTEGER as ce100BtxSx01TPRecv  
  INTEGER as ce100BtxSx01FiberRecv  
  INTEGER as ce100BtxSx01TPSignalDetect  
  INTEGER as ce100BtxSx01FiberSignalDetect  
  INTEGER as ce100BtxSx01Power  

Ce100BtxFx04MtEntry  
SEQUENCE    
  INTEGER as ce100BtxFx04MtIndex  
  INTEGER as ce100BtxFx04MtTPRecv  
  INTEGER as ce100BtxFx04MtFiberRecv  
  INTEGER as ce100BtxFx04MtTPSignalDetect  
  INTEGER as ce100BtxFx04MtFiberSignalDetect  
  INTEGER as ce100BtxFx04MtPower  

CfdCd01Entry  
SEQUENCE    
  INTEGER as cfdCd01Index  
  INTEGER as cfdCd01Lock  
  INTEGER as cfdCd01TPRecv  
  INTEGER as cfdCd01FiberRecv  
  INTEGER as cfdCd01TPSignalDetect  
  INTEGER as cfdCd01FiberSignalDetect  

CtrCf01Entry  
SEQUENCE    
  INTEGER as ctrCf01Index  
  INTEGER as ctrCf01FiberinOK  
  INTEGER as ctrCf01TPinOK  
  INTEGER as ctrCf01Inserted  

Ce100BtxFrl03Entry  
SEQUENCE    
  INTEGER as ce100BtxFrl03Index  
  INTEGER as ce100BtxFrl03Lock  
  INTEGER as ce100BtxFrl03TPRecv  
  INTEGER as ce100BtxFrl03FiberRecv  
  INTEGER as ce100BtxFrl03TPSignalDetect  
  INTEGER as ce100BtxFrl03FiberSignalDetect  

ChstrCf01Entry  
SEQUENCE    
  INTEGER as chstrCf01Index  
  INTEGER as chstrCf01TPRecv  
  INTEGER as chstrCf01FiberRecv  
  INTEGER as chstrCf01TPSignalDetect  
  INTEGER as chstrCf01FiberSignalDetect  

CeTxSx02Entry  
SEQUENCE    
  INTEGER as ceTxSx02Index  
  INTEGER as ceTxSx02TPLink  
  INTEGER as ceTxSx02FiberLink  
  INTEGER as ceTxSx02100Mbps  

CeTbtFrl04Entry  
SEQUENCE    
  INTEGER as ceTbtFrl04Index  
  INTEGER as ceTbtFrl04FiberRecv  
  INTEGER as ceTbtFrl04FiberLink  
  INTEGER as ceTbtFrl04TPRecv  
  INTEGER as ceTbtFrl04TPLink  

CpsModuleEntry  
SEQUENCE    
  INTEGER as cpsModuleBiaIndex  
  INTEGER as cpsModuleSlotIndex  
  OBJECT IDENTIFIER as cpsModuleModel  

Cpsmm100Entry  
SEQUENCE    
  INTEGER as cpsmm100BiaIndex  
  INTEGER as cpsmm100SlotIndex  
  DisplayString as cpsmm100Groups  
  INTEGER as cpsmm100Reset  
  INTEGER as cpsmm100SaveConfig  
  DisplayString as cpsmm100HwRevision  
  DisplayString as cpsmm100SwRevision  
  IpAddress as cpsmm100IPAddress  
  IpAddress as cpsmm100SubnetMask  
  IpAddress as cpsmm100Gateway  
  INTEGER as cpsmm100IsPrimary  
  INTEGER as cpsmm100WantPrimary  
  INTEGER as cpsmm100CanPrimary  
  INTEGER as cpsmm100EthernetLink  
  IpAddress as cpsmm100TntRIP  
  IpAddress as cpsmm100TntRIPMask  
  IpAddress as cpsmm100SNMPTrapMgr  
  INTEGER as cpsmm100SNMPTrapInterval  
  TimeTicks as cpsmm100SysUpTime  
  DisplayString as cpsmm100SysContact  
  DisplayString as cpsmm100SysName  
  DisplayString as cpsmm100SysLocation  
  INTEGER as cpsmm100CfgMatch  
  INTEGER as cpsmm100SerialNumber  
  INTEGER as cpsmm100ICIF  
  INTEGER as cpsmm100MRevision  
  INTEGER as cpsmm100LastGasp  
  IpAddress as cpsmm100SNMPTrapMgr2  
  IpAddress as cpsmm100SNMPTrapMgr3  
  IpAddress as cpsmm100SNMPTrapMgr4  
  INTEGER as cpsmm100CacheClean  

Cpsmm200Entry  
SEQUENCE    
  INTEGER as cpsmm200BiaIndex  
  INTEGER as cpsmm200SlotIndex  
  INTEGER as cpsmm200SerialNumber  
  INTEGER as cpsmm200ICIF  
  INTEGER as cpsmm200MRevision  

Cettf100Entry  
SEQUENCE    
  INTEGER as cettf100BiaIndex  
  INTEGER as cettf100SlotIndex  
  DisplayString as cettf100Groups  
  INTEGER as cettf100MRevision  
  INTEGER as cettf100CfgMatch  
  INTEGER as cettf100SerialNumber  
  INTEGER as cettf100ConnA  
  INTEGER as cettf100ConnB  
  INTEGER as cettf100TPLink  
  INTEGER as cettf100FiberLink  
  INTEGER as cettf100Fault  
  INTEGER as cettf100TPActivity  
  INTEGER as cettf100FiberActivity  
  INTEGER as cettf100AutoCross  
  INTEGER as cettf100LinkPassThrough  
  INTEGER as cettf100ConfigMode  
  INTEGER as cettf100Enabled  
  INTEGER as cettf100CacheClean  

Cfetf100Entry  
SEQUENCE    
  INTEGER as cfetf100BiaIndex  
  INTEGER as cfetf100SlotIndex  
  DisplayString as cfetf100Groups  
  INTEGER as cfetf100MRevision  
  INTEGER as cfetf100CfgMatch  
  INTEGER as cfetf100SerialNumber  
  INTEGER as cfetf100ConnA  
  INTEGER as cfetf100ConnB  
  INTEGER as cfetf100TPLink  
  INTEGER as cfetf100FiberLink  
  INTEGER as cfetf100Fault  
  INTEGER as cfetf100FastLinkPulse  
  INTEGER as cfetf100Enabled  
  INTEGER as cfetf100Pause  
  INTEGER as cfetf100LinkPassThrough  
  INTEGER as cfetf100AutoCross  
  INTEGER as cfetf100TPActivity  
  INTEGER as cfetf100FiberActivity  
  INTEGER as cfetf100ConfigMode  
  INTEGER as cfetf100FarEndFault  
  INTEGER as cfetf100CacheClean  

Cfmff100Entry  
SEQUENCE    
  INTEGER as cfmff100BiaIndex  
  INTEGER as cfmff100SlotIndex  
  DisplayString as cfmff100Groups  
  INTEGER as cfmff100MRevision  
  INTEGER as cfmff100CfgMatch  
  INTEGER as cfmff100ConnA  
  INTEGER as cfmff100ConnB  
  INTEGER as cfmff100SerialNumber  
  INTEGER as cfmff100SMSignal  
  INTEGER as cfmff100MMSignal  
  INTEGER as cfmff100Enabled  
  INTEGER as cfmff100PortShutOff  
  INTEGER as cfmff100ConfigMode  
  INTEGER as cfmff100CacheClean  

Cpsmp100Entry  
SEQUENCE    
  INTEGER as cpsmp100BiaIndex  
  INTEGER as cpsmp100SlotIndex  
  DisplayString as cpsmp100Groups  
  INTEGER as cpsmp100MRevision  
  INTEGER as cpsmp100CfgMatch  
  INTEGER as cpsmp100SerialNumber  
  INTEGER as cpsmp100Mode  
  INTEGER as cpsmp100ConfigMode  
  INTEGER as cpsmp100RemoteFan  
  INTEGER as cpsmp100PowerOK  
  INTEGER as cpsmp100InUse  
  INTEGER as cpsmp100ChassisPower  
  INTEGER as cpsmp100ChassisTemp  
  INTEGER as cpsmp100RFanFault  
  INTEGER as cpsmp100LFanFault  
  INTEGER as cpsmp100SupplyType  
  INTEGER as cpsmp100CacheClean  

Csetf100Entry  
SEQUENCE    
  INTEGER as csetf100BiaIndex  
  INTEGER as csetf100SlotIndex  
  DisplayString as csetf100Groups  
  INTEGER as csetf100MRevision  
  INTEGER as csetf100CfgMatch  
  INTEGER as csetf100SerialNumber  
  INTEGER as csetf100ConnA  
  INTEGER as csetf100ConnB  
  INTEGER as csetf100TPLink  
  INTEGER as csetf100FiberLink  
  INTEGER as csetf100AutoCross  
  INTEGER as csetf100SpeedConfig  
  INTEGER as csetf100Speed100Mbps  
  INTEGER as csetf100TPActivity  
  INTEGER as csetf100FiberActivity  
  INTEGER as csetf100ConfigMode  
  INTEGER as csetf100CacheClean  

Cgetf100Entry  
SEQUENCE    
  INTEGER as cgetf100BiaIndex  
  INTEGER as cgetf100SlotIndex  
  DisplayString as cgetf100Groups  
  INTEGER as cgetf100MRevision  
  INTEGER as cgetf100CfgMatch  
  INTEGER as cgetf100SerialNumber  
  INTEGER as cgetf100ConnA  
  INTEGER as cgetf100ConnB  
  INTEGER as cgetf100TPLink  
  INTEGER as cgetf100FiberLink  
  INTEGER as cgetf100Fault  
  INTEGER as cgetf100Enabled  
  INTEGER as cgetf100Pause  
  INTEGER as cgetf100LinkPassThrough  
  INTEGER as cgetf100FullDuplex  
  INTEGER as cgetf100ClockMaster  
  INTEGER as cgetf100ConfigMode  
  INTEGER as cgetf100TPLength  
  INTEGER as cgetf100FiberAutoNegot  
  INTEGER as cgetf100CacheClean  
  INTEGER as cgetf100PauseType  

Csdtf100Entry  
SEQUENCE    
  INTEGER as csdtf100BiaIndex  
  INTEGER as csdtf100SlotIndex  
  DisplayString as csdtf100Groups  
  INTEGER as csdtf100MRevision  
  INTEGER as csdtf100CfgMatch  
  INTEGER as csdtf100SerialNumber  
  INTEGER as csdtf100ConnA  
  INTEGER as csdtf100ConnB  
  INTEGER as csdtf100CopperLink  
  INTEGER as csdtf100FiberLink  
  INTEGER as csdtf100Fault  
  INTEGER as csdtf100TAOSFiber  
  INTEGER as csdtf100TAOSCopper  
  INTEGER as csdtf100AISFiber  
  INTEGER as csdtf100AISCopper  
  INTEGER as csdtf100CopperLoopback  
  INTEGER as csdtf100CopperLongHaul  
  INTEGER as csdtf100T1E1  
  INTEGER as csdtf100ConfigMode  
  INTEGER as csdtf100TPCoax  
  INTEGER as csdtf100CopperLineBuildout  
  INTEGER as csdtf100FiberLoopback  
  INTEGER as csdtf100RmtSupported  
  INTEGER as csdtf100RmtDetected  
  INTEGER as csdtf100RmtMRevision  
  INTEGER as csdtf100RmtSerialNumber  
  INTEGER as csdtf100RmtConnA  
  INTEGER as csdtf100RmtConnB  
  INTEGER as csdtf100RmtCopperLink  
  INTEGER as csdtf100RmtFiberLink  
  INTEGER as csdtf100RmtFault  
  INTEGER as csdtf100RmtTAOSFiber  
  INTEGER as csdtf100RmtTAOSCopper  
  INTEGER as csdtf100RmtAISFiber  
  INTEGER as csdtf100RmtAISCopper  
  INTEGER as csdtf100RmtCopperLoopback  
  INTEGER as csdtf100RmtCopperLongHaul  
  INTEGER as csdtf100RmtConfigMode  
  INTEGER as csdtf100RmtTPCoax  
  INTEGER as csdtf100RmtCopperLineBuildout  
  INTEGER as csdtf100RmtFiberLoopback  
  INTEGER as csdtf100CacheClean  

Cpsmp110Entry  
SEQUENCE    
  INTEGER as cpsmp110SubDeviceIndex  
  INTEGER as cpsmp110BiaIndex  
  INTEGER as cpsmp110SlotIndex  
  DisplayString as cpsmp110Groups  
  INTEGER as cpsmp110MRevision  
  INTEGER as cpsmp110CfgMatch  
  INTEGER as cpsmp110SerialNumber  
  INTEGER as cpsmp110ConfigMode  
  INTEGER as cpsmp110MasterTempFault  
  INTEGER as cpsmp110MasterCurrentFault  
  INTEGER as cpsmp110MasterFanFault  
  INTEGER as cpsmp110FirmwareRevision  
  INTEGER as cpsmp110PSSupplyTbl  
  INTEGER as cpsmp110PSRoleTbl  
  INTEGER as cpsmp110PSReadyTbl  
  INTEGER as cpsmp110PSInUseTbl  
  INTEGER as cpsmp110TemperatureTbl  
  INTEGER as cpsmp110CurrentTbl  
  INTEGER as cpsmp110FanStatusTbl  
  INTEGER as cpsmp110TempFaultTbl  
  INTEGER as cpsmp110CurrFaultTbl  
  INTEGER as cpsmp110PSCount  
  INTEGER as cpsmp110TempSensorCount  
  INTEGER as cpsmp110CurrSensorCount  
  INTEGER as cpsmp110FanCount  
  INTEGER as cpsmp110CacheClean  

Cbftf100Entry  
SEQUENCE    
  INTEGER as cbftf100SubDeviceIndex  
  INTEGER as cbftf100BiaIndex  
  INTEGER as cbftf100SlotIndex  
  DisplayString as cbftf100Groups  
  INTEGER as cbftf100MRevision  
  INTEGER as cbftf100CfgMatch  
  INTEGER as cbftf100SerialNumber  
  INTEGER as cbftf100ConfigMode  
  INTEGER as cbftf100FirmwareRevision  
  INTEGER as cbftf100SelfTestFailed  
  INTEGER as cbftf100SpanningTree  
  INTEGER as cbftf100MirrorCfg  
  INTEGER as cbftf100SACMasterCfg  
  INTEGER as cbftf100FormFactor  
  INTEGER as cbftf100AutoNegotTbl  
  INTEGER as cbftf100FullDuplexTbl  
  INTEGER as cbftf100100MbpsTbl  
  INTEGER as cbftf100Adv10HDXTbl  
  INTEGER as cbftf100Adv10FDXTbl  
  INTEGER as cbftf100Adv100HDXTbl  
  INTEGER as cbftf100Adv100FDXTbl  
  INTEGER as cbftf100CrossTbl  
  INTEGER as cbftf100PauseCfgTbl  
  INTEGER as cbftf100PauseStatTbl  
  INTEGER as cbftf100FarEndFaultTbl  
  INTEGER as cbftf100ConnectorTbl  
  INTEGER as cbftf100SACCfgTbl  
  INTEGER as cbftf100SACStatTbl  
  INTEGER as cbftf100MirrorSelTbl  
  INTEGER as cbftf100MirrorInTbl  
  INTEGER as cbftf100MirrorOutTbl  
  INTEGER as cbftf100LinkTbl  
  INTEGER as cbftf100PortCount  
  INTEGER as cbftf100LinkPassThrough  
  INTEGER as cbftf100CacheClean  
  INTEGER as cbftf100RedundantPath  

Cetct100Entry  
SEQUENCE    
  INTEGER as cetct100BiaIndex  
  INTEGER as cetct100SlotIndex  
  DisplayString as cetct100Groups  
  INTEGER as cetct100MRevision  
  INTEGER as cetct100CfgMatch  
  INTEGER as cetct100SerialNumber  
  INTEGER as cetct100ConfigMode  
  INTEGER as cetct100FirmwareRevision  
  INTEGER as cetct100TPLink  
  INTEGER as cetct100Collision  
  INTEGER as cetct100CoaxActivity  
  INTEGER as cetct100TPActivity  
  INTEGER as cetct100CollisionsPerMinute  
  INTEGER as cetct100CollisionsPerHour  
  INTEGER as cetct100ConnB  
  INTEGER as cetct100ConnA  
  INTEGER as cetct100CacheClean  

Ccscf100Entry  
SEQUENCE    
  INTEGER as ccscf100BiaIndex  
  INTEGER as ccscf100SlotIndex  
  DisplayString as ccscf100Groups  
  INTEGER as ccscf100MRevision  
  INTEGER as ccscf100CfgMatch  
  INTEGER as ccscf100SerialNumber  
  INTEGER as ccscf100ConfigMode  
  INTEGER as ccscf100FiberLink  
  INTEGER as ccscf100CopperLink  
  INTEGER as ccscf100AISFiber  
  INTEGER as ccscf100AISCopper  
  INTEGER as ccscf100DS3LineBuildout  
  INTEGER as ccscf100E3DS3  
  INTEGER as ccscf100CopperLoopback  
  INTEGER as ccscf100FiberLoopback  
  INTEGER as ccscf100ConnA  
  INTEGER as ccscf100ConnB  
  INTEGER as ccscf100CacheClean  

Cfetf105Entry  
SEQUENCE    
  INTEGER as cfetf105BiaIndex  
  INTEGER as cfetf105SlotIndex  
  DisplayString as cfetf105Groups  
  INTEGER as cfetf105MRevision  
  INTEGER as cfetf105CfgMatch  
  INTEGER as cfetf105SerialNumber  
  INTEGER as cfetf105ConnA  
  INTEGER as cfetf105ConnB  
  INTEGER as cfetf105TPLink  
  INTEGER as cfetf105FiberLink  
  INTEGER as cfetf105AutoNegot  
  INTEGER as cfetf105LinkPassThrough  
  INTEGER as cfetf105AutoCross  
  INTEGER as cfetf105TPActivity  
  INTEGER as cfetf105FiberActivity  
  INTEGER as cfetf105ConfigMode  
  INTEGER as cfetf105CacheClean  

Smacf100PEntry  
SEQUENCE    
  INTEGER as smacf100PSubDeviceIndex  
  INTEGER as smacf100PBiaIndex  
  INTEGER as smacf100PSlotIndex  
  DisplayString as smacf100PGroups  
  INTEGER as smacf100PCfgMatch  
  INTEGER as smacf100PConnA  
  INTEGER as smacf100PLink  
  INTEGER as smacf100P100Mbps  
  INTEGER as smacf100PFullDuplex  
  INTEGER as smacf100PSACStat  
  INTEGER as smacf100PEnabled  
  INTEGER as smacf100PAutoNegot  
  INTEGER as smacf100PAdv10HDX  
  INTEGER as smacf100PAdv10FDX  
  INTEGER as smacf100PAdv100HDX  
  INTEGER as smacf100PAdv100FDX  
  INTEGER as smacf100PSTPState  
  MacAddress as smacf100PLastMAC  
  INTEGER as smacf100PFarEndFaultCfg  
  INTEGER as smacf100PFarEndFaultStat  
  INTEGER as smacf100PTxOctets  
  INTEGER as smacf100PWrapTxOctets  
  INTEGER as smacf100PRxOctets  
  INTEGER as smacf100PWrapRxOctets  
  INTEGER as smacf100PSACCfg  
  INTEGER as smacf100PBlockMgmt  
  INTEGER as smacf100PBlockPort  
  INTEGER as smacf100PTxDropPkts  
  INTEGER as smacf100PTxBroadcastPkts  
  INTEGER as smacf100PTxMulticastPkts  
  INTEGER as smacf100PTxUnicastPkts  
  INTEGER as smacf100PTxCollisions  
  INTEGER as smacf100PTxSingleCollision  
  INTEGER as smacf100PTxMultipleCollision  
  INTEGER as smacf100PTxDeferredTransmit  
  INTEGER as smacf100PTxLateCollision  
  INTEGER as smacf100PTxExcessiveCollision  
  INTEGER as smacf100PTxFrameInDisc  
  INTEGER as smacf100PTxPausePkts  
  INTEGER as smacf100PRxUndersizePkts  
  INTEGER as smacf100PRxPausePkts  
  INTEGER as smacf100PPkts64Octets  
  INTEGER as smacf100PPkts65to127Octets  
  INTEGER as smacf100PPkts128to255Octets  
  INTEGER as smacf100PPkts256to511Octets  
  INTEGER as smacf100PPkts512to1023Octets  
  INTEGER as smacf100PPkts1024to1522Octets  
  INTEGER as smacf100PRxOversizePkts  
  INTEGER as smacf100PRxJabbers  
  INTEGER as smacf100PRxAlignmentErrors  
  INTEGER as smacf100PRxFCSErrors  
  INTEGER as smacf100PRxGoodOctets  
  INTEGER as smacf100PWrapRxGoodOctets  
  INTEGER as smacf100PRxDropPkts  
  INTEGER as smacf100PRxUnicastPkts  
  INTEGER as smacf100PRxMulticastPkts  
  INTEGER as smacf100PRxBroadcastPkts  
  INTEGER as smacf100PRxSAChanges  
  INTEGER as smacf100PRxFragments  
  INTEGER as smacf100PRxExcessSizeDisc  
  INTEGER as smacf100PRxSymbolError  
  INTEGER as smacf100PQosPriority  
  INTEGER as smacf100PQosPause  
  INTEGER as smacf100PAdvPause  
  INTEGER as smacf100PCacheClean  

Cpsld100Entry  
SEQUENCE    
  INTEGER as cpsld100BiaIndex  
  INTEGER as cpsld100SlotIndex  
  INTEGER as cpsld100SerialNumber  
  INTEGER as cpsld100MRevision  
  INTEGER as cpsld100Ps1Power  
  INTEGER as cpsld100Ps1InUse  
  INTEGER as cpsld100Ps2Power  
  INTEGER as cpsld100Ps2InUse  

Cdftf100Entry  
SEQUENCE    
  INTEGER as cdftf100SubDeviceIndex  
  INTEGER as cdftf100BiaIndex  
  INTEGER as cdftf100SlotIndex  
  DisplayString as cdftf100Groups  
  INTEGER as cdftf100CfgMatch  
  INTEGER as cdftf100SerialNumber  
  INTEGER as cdftf100MRevision  
  INTEGER as cdftf100TPLinkTbl  
  INTEGER as cdftf100FiberLinkTbl  
  INTEGER as cdftf100TPActivityTbl  
  INTEGER as cdftf100FiberActivityTbl  
  INTEGER as cdftf100ConnectorTbl  
  INTEGER as cdftf100FirmwareRevision  
  INTEGER as cdftf100CacheClean  

Cpsvt100Entry  
SEQUENCE    
  INTEGER as cpsvt100BiaIndex  
  INTEGER as cpsvt100SlotIndex  
  DisplayString as cpsvt100Groups  
  INTEGER as cpsvt100MRevision  
  INTEGER as cpsvt100CfgMatch  
  INTEGER as cpsvt100SerialNumber  
  INTEGER as cpsvt100FiberLink  
  INTEGER as cpsvt100CopperLink  
  INTEGER as cpsvt100Fault  
  INTEGER as cpsvt100ConnA  
  INTEGER as cpsvt100ConnB  
  INTEGER as cpsvt100TermTiming  
  INTEGER as cpsvt100LoopBack  
  INTEGER as cpsvt100CableMode  
  INTEGER as cpsvt100DCE  
  INTEGER as cpsvt100InvertTX  
  INTEGER as cpsvt100InvertRX  
  INTEGER as cpsvt100ConfigMode  
  INTEGER as cpsvt100FirmwareRev  
  INTEGER as cpsvt100RmtDetected  
  INTEGER as cpsvt100RmtTermTiming  
  INTEGER as cpsvt100RmtLoopBack  
  INTEGER as cpsvt100RmtCableMode  
  INTEGER as cpsvt100RmtDCE  
  INTEGER as cpsvt100RmtInvertTX  
  INTEGER as cpsvt100RmtInvertRX  
  INTEGER as cpsvt100RmtConfigMode  
  INTEGER as cpsvt100RmtFirmwareRev  
  INTEGER as cpsvt100RmtCopperLink  
  INTEGER as cpsvt100RmtFiberLink  
  INTEGER as cpsvt100CacheClean  

Cemtf100Entry  
SEQUENCE    
  INTEGER as cemtf100BiaIndex  
  INTEGER as cemtf100SlotIndex  
  DisplayString as cemtf100Groups  
  INTEGER as cemtf100MRevision  
  INTEGER as cemtf100CfgMatch  
  INTEGER as cemtf100SerialNumber  
  INTEGER as cemtf100FiberLink  
  INTEGER as cemtf100OffHook  
  INTEGER as cemtf100Fault  
  INTEGER as cemtf100ConnA  
  INTEGER as cemtf100ConnB  
  INTEGER as cemtf100CacheClean  

Captf100Entry  
SEQUENCE    
  INTEGER as captf100BiaIndex  
  INTEGER as captf100SlotIndex  
  DisplayString as captf100Groups  
  INTEGER as captf100MRevision  
  INTEGER as captf100CfgMatch  
  INTEGER as captf100SerialNumber  
  INTEGER as captf100FiberLink  
  INTEGER as captf100InUse  
  INTEGER as captf100Fault  
  INTEGER as captf100ConnA  
  INTEGER as captf100ConnB  
  INTEGER as captf100FirmwareRev  
  INTEGER as captf100CacheClean  
  INTEGER as captf100Emulates  

Cfetf205Entry  
SEQUENCE    
  INTEGER as cfetf205BiaIndex  
  INTEGER as cfetf205SlotIndex  
  DisplayString as cfetf205Groups  
  INTEGER as cfetf205MRevision  
  INTEGER as cfetf205CfgMatch  
  INTEGER as cfetf205SerialNumber  
  INTEGER as cfetf205ConnA  
  INTEGER as cfetf205ConnB  
  INTEGER as cfetf205TPLink  
  INTEGER as cfetf205FiberLink  
  INTEGER as cfetf205Fault  
  INTEGER as cfetf205FastLinkPulse  
  INTEGER as cfetf205Enabled  
  INTEGER as cfetf205Pause  
  INTEGER as cfetf205LinkPassThrough  
  INTEGER as cfetf205AutoCross  
  INTEGER as cfetf205TPActivity  
  INTEGER as cfetf205FiberActivity  
  INTEGER as cfetf205ConfigMode  
  INTEGER as cfetf205FarEndFault  
  INTEGER as cfetf205CacheClean  

Cbftf150Entry  
SEQUENCE    
  INTEGER as cbftf150SubDeviceIndex  
  INTEGER as cbftf150BiaIndex  
  INTEGER as cbftf150SlotIndex  
  DisplayString as cbftf150Groups  
  INTEGER as cbftf150MRevision  
  INTEGER as cbftf150CfgMatch  
  INTEGER as cbftf150SerialNumber  
  INTEGER as cbftf150ConfigMode  
  INTEGER as cbftf150FirmwareRevision  
  INTEGER as cbftf150FormFactor  
  INTEGER as cbftf150AutoNegotTbl  
  INTEGER as cbftf150FullDuplexTbl  
  INTEGER as cbftf150100MbpsTbl  
  INTEGER as cbftf150CrossTbl  
  INTEGER as cbftf150FarEndFaultTbl  
  INTEGER as cbftf150ConnectorTbl  
  INTEGER as cbftf150LinkTbl  
  INTEGER as cbftf150PortCount  
  INTEGER as cbftf150CacheClean  

Cgfeb100Entry  
SEQUENCE    
  INTEGER as cgfeb100BiaIndex  
  INTEGER as cgfeb100SlotIndex  
  DisplayString as cgfeb100Groups  
  INTEGER as cgfeb100MRevision  
  INTEGER as cgfeb100CfgMatch  
  INTEGER as cgfeb100SerialNumber  
  INTEGER as cgfeb100ConfigMode  
  INTEGER as cgfeb100FirmwareRevision  
  INTEGER as cgfeb100SelfTestFailed  
  INTEGER as cgfeb100MonitorType  
  INTEGER as cgfeb100LinkPassThrough  
  INTEGER as cgfeb100QosEnabled  
  INTEGER as cgfeb100QosHPThreshold  
  INTEGER as cgfeb100QosLqWeight  
  INTEGER as cgfeb100QosHqWeight  
  INTEGER as cgfeb100ConnA  
  INTEGER as cgfeb100TPLink  
  INTEGER as cgfeb100TPSpeedCfg  
  INTEGER as cgfeb100TPSpeedStat  
  INTEGER as cgfeb100TPFullDuplexCfg  
  INTEGER as cgfeb100TPFullDuplexStat  
  INTEGER as cgfeb100TPCrossCfg  
  INTEGER as cgfeb100TPCrossStat  
  INTEGER as cgfeb100TPAutoNegot  
  INTEGER as cgfeb100TPAdv10HDX  
  INTEGER as cgfeb100TPAdv10FDX  
  INTEGER as cgfeb100TPAdv100HDX  
  INTEGER as cgfeb100TPAdv100FDX  
  INTEGER as cgfeb100TPAdv1000HDX  
  INTEGER as cgfeb100TPAdv1000FDX  
  INTEGER as cgfeb100TPLpAdvPause  
  INTEGER as cgfeb100TPLpAdv10HDX  
  INTEGER as cgfeb100TPLpAdv10FDX  
  INTEGER as cgfeb100TPLpAdv100HDX  
  INTEGER as cgfeb100TPLpAdv100FDX  
  INTEGER as cgfeb100TPLpAdv1000HDX  
  INTEGER as cgfeb100TPLpAdv1000FDX  
  INTEGER as cgfeb100TPAdvPause  
  INTEGER as cgfeb100TPQosPause  
  INTEGER as cgfeb100TPSacCfg  
  INTEGER as cgfeb100TPSacStat  
  INTEGER as cgfeb100ConnB  
  INTEGER as cgfeb100FiberLink  
  INTEGER as cgfeb100FiberFullDuplexCfg  
  INTEGER as cgfeb100FiberFullDuplexStat  
  INTEGER as cgfeb100FiberAutoNegot  
  INTEGER as cgfeb100FiberAdv1000HDX  
  INTEGER as cgfeb100FiberAdv1000FDX  
  INTEGER as cgfeb100FiberLpAdv1000HDX  
  INTEGER as cgfeb100FiberLpAdv1000FDX  
  INTEGER as cgfeb100FiberLpAdvPause  
  INTEGER as cgfeb100FiberAdvPause  
  INTEGER as cgfeb100FiberQosPause  
  INTEGER as cgfeb100FiberSacCfg  
  INTEGER as cgfeb100FiberSacStat  
  INTEGER as cgfeb100MonitorTap  
  INTEGER as cgfeb100CacheClean  

Crmfe100Entry  
SEQUENCE    
  INTEGER as crmfe100BiaIndex  
  INTEGER as crmfe100SlotIndex  
  DisplayString as crmfe100Groups  
  INTEGER as crmfe100MRevision  
  INTEGER as crmfe100CfgMatch  
  INTEGER as crmfe100SerialNumber  
  INTEGER as crmfe100ConnA  
  INTEGER as crmfe100ConnB  
  INTEGER as crmfe100TPLink  
  INTEGER as crmfe100FiberLink  
  INTEGER as crmfe100Fault  
  INTEGER as crmfe100Autonegot  
  INTEGER as crmfe100Enabled  
  INTEGER as crmfe100Pause  
  INTEGER as crmfe100LinkPassThrough  
  INTEGER as crmfe100AutoCross  
  INTEGER as crmfe100TPActivity  
  INTEGER as crmfe100FiberActivity  
  INTEGER as crmfe100ConfigMode  
  INTEGER as crmfe100FarEndFault  
  INTEGER as crmfe100NetworkMode  
  TimeTicks as crmfe100UpTime  
  INTEGER as crmfe100FirmwareRevision  
  INTEGER as crmfe100RmtDetected  
  INTEGER as crmfe100RmtTPLink  
  INTEGER as crmfe100RmtFiberLink  
  INTEGER as crmfe100RmtFault  
  INTEGER as crmfe100RmtAutonegot  
  INTEGER as crmfe100RmtPause  
  INTEGER as crmfe100RmtLinkPassThrough  
  INTEGER as crmfe100RmtAutoCross  
  INTEGER as crmfe100RmtTPActivity  
  INTEGER as crmfe100RmtFiberActivity  
  INTEGER as crmfe100RmtConfigMode  
  INTEGER as crmfe100RmtFarEndFault  
  INTEGER as crmfe100RmtLoopback  
  INTEGER as crmfe100RmtNetworkMode  
  TimeTicks as crmfe100RmtUpTime  
  INTEGER as crmfe100TxFxBwa  
  INTEGER as crmfe100FxTxBwa  
  INTEGER as crmfe100TxBytesH  
  INTEGER as crmfe100TxBytesL  
  INTEGER as crmfe100FxBytesH  
  INTEGER as crmfe100FxBytesL  
  INTEGER as crmfe100MscRxBytes  
  INTEGER as crmfe100MscTxBytes  
  INTEGER as crmfe100CacheClean  
  INTEGER as crmfe100MbTxFxBwa  
  INTEGER as crmfe100MbFxTxBwa  

Crs2f100Entry  
SEQUENCE    
  INTEGER as crs2f100BiaIndex  
  INTEGER as crs2f100SlotIndex  
  DisplayString as crs2f100Groups  
  INTEGER as crs2f100MRevision  
  INTEGER as crs2f100CfgMatch  
  INTEGER as crs2f100SerialNumber  
  INTEGER as crs2f100ConnA  
  INTEGER as crs2f100ConnB  
  INTEGER as crs2f100FiberLink  
  INTEGER as crs2f100Fault  
  INTEGER as crs2f100FirmwareRevision  
  INTEGER as crs2f100Loopback  
  INTEGER as crs2f100DCE  
  INTEGER as crs2f100CopperActivity  
  INTEGER as crs2f100ConfigMode  
  INTEGER as crs2f100RmtDetected  
  INTEGER as crs2f100RmtLoopback  
  INTEGER as crs2f100RmtDCE  
  INTEGER as crs2f100RmtCopperActivity  
  INTEGER as crs2f100RmtConfigMode  
  INTEGER as crs2f100CacheClean  

Crs4f100Entry  
SEQUENCE    
  INTEGER as crs4f100BiaIndex  
  INTEGER as crs4f100SlotIndex  
  DisplayString as crs4f100Groups  
  INTEGER as crs4f100MRevision  
  INTEGER as crs4f100CfgMatch  
  INTEGER as crs4f100SerialNumber  
  INTEGER as crs4f100ConnA  
  INTEGER as crs4f100ConnB  
  INTEGER as crs4f100FiberLink  
  INTEGER as crs4f100Fault  
  INTEGER as crs4f100FirmwareRevision  
  INTEGER as crs4f100CopperActivity  
  INTEGER as crs4f100CacheClean  

Cmefg100Entry  
SEQUENCE    
  INTEGER as cmefg100SubDeviceIndex  
  INTEGER as cmefg100BiaIndex  
  INTEGER as cmefg100SlotIndex  
  DisplayString as cmefg100Groups  
  INTEGER as cmefg100MRevision  
  INTEGER as cmefg100CfgMatch  
  INTEGER as cmefg100ImcLocEnable  
  INTEGER as cmefg100ImcLocReset  
  INTEGER as cmefg100ImcRmtEnable  
  INTEGER as cmefg100ImcRmtReset  
  INTEGER as cmefg100ImcRxAlignmentErrorsTbl  
  INTEGER as cmefg100ImcRxBroadcastPktsTbl  
  INTEGER as cmefg100ImcRxDropPktsTbl  
  INTEGER as cmefg100ImcRxExcessSizeDiscTbl  
  INTEGER as cmefg100ImcRxFCSErrorsTbl  
  INTEGER as cmefg100ImcRxFragmentsTbl  
  INTEGER as cmefg100ImcRxGoodOctetsTbl  
  INTEGER as cmefg100ImcRxGoodOctetsWrapTbl  
  INTEGER as cmefg100ImcRxJabbersTbl  
  INTEGER as cmefg100ImcRxMulticastPktsTbl  
  INTEGER as cmefg100ImcRxOctetsTbl  
  INTEGER as cmefg100ImcRxOctetsWrapTbl  
  INTEGER as cmefg100ImcRxOversizePktsTbl  
  INTEGER as cmefg100ImcRxPausePktsTbl  
  INTEGER as cmefg100ImcRxPkts1024to1522OctetsTbl  
  INTEGER as cmefg100ImcRxPkts128to255OctetsTbl  
  INTEGER as cmefg100ImcRxPkts256to511OctetsTbl  
  INTEGER as cmefg100ImcRxPkts512to1023OctetsTbl  
  INTEGER as cmefg100ImcRxPkts64OctetsTbl  
  INTEGER as cmefg100ImcRxPkts65to127OctetsTbl  
  INTEGER as cmefg100ImcRxQosOctetsTbl  
  INTEGER as cmefg100ImcRxQosOctetsWrapTbl  
  INTEGER as cmefg100ImcRxQosPktsTbl  
  INTEGER as cmefg100ImcRxSAChangesTbl  
  INTEGER as cmefg100ImcRxSymbolErrorTbl  
  INTEGER as cmefg100ImcRxUndersizePktsTbl  
  INTEGER as cmefg100ImcRxUnicastPktsTbl  
  INTEGER as cmefg100ImcTxBroadcastPktsTbl  
  INTEGER as cmefg100ImcTxCollisionsTbl  
  INTEGER as cmefg100ImcTxDeferredTransmitTbl  
  INTEGER as cmefg100ImcTxDropPktsTbl  
  INTEGER as cmefg100ImcTxExcessiveCollisionTbl  
  INTEGER as cmefg100ImcTxFrameInDiscTbl  
  INTEGER as cmefg100ImcTxLateCollisionTbl  
  INTEGER as cmefg100ImcTxMulticastPktsTbl  
  INTEGER as cmefg100ImcTxMultipleCollisionTbl  
  INTEGER as cmefg100ImcTxOctetsTbl  
  INTEGER as cmefg100ImcTxOctetsWrapTbl  
  INTEGER as cmefg100ImcTxPausePktsTbl  
  INTEGER as cmefg100ImcTxQosOctetsTbl  
  INTEGER as cmefg100ImcTxQosOctetsWrapTbl  
  INTEGER as cmefg100ImcTxQosPktsTbl  
  INTEGER as cmefg100ImcTxSingleCollisionTbl  
  INTEGER as cmefg100ImcTxUnicastPktsTbl  
  INTEGER as cmefg100LadCacheCmd  
  INTEGER as cmefg100LadCacheState  
  INTEGER as cmefg100LadEditCmd  
  OCTET STRING as cmefg100LadEditMac  
  INTEGER as cmefg100LadEditPort  
  INTEGER as cmefg100LadEditVid  
  INTEGER as cmefg100LadEntries  
  MacAddress as cmefg100LadMacTbl  
  INTEGER as cmefg100LadPortTbl  
  INTEGER as cmefg100LadStaticTbl  
  INTEGER as cmefg100LadVidTbl  
  INTEGER as cmefg100LocColdstart  
  INTEGER as cmefg100LocDmiRxPower  
  INTEGER as cmefg100LocDmiRxPowerAlarm  
  INTEGER as cmefg100LocDmiTemp  
  INTEGER as cmefg100LocDmiTempAlarm  
  INTEGER as cmefg100LocDmiTxBiasAlarm  
  INTEGER as cmefg100LocDmiTxBiasCurrent  
  INTEGER as cmefg100LocDmiTxPower  
  INTEGER as cmefg100LocDmiTxPowerAlarm  
  INTEGER as cmefg100LocFiberAdv1000FDX  
  INTEGER as cmefg100LocFiberAdv1000HDX  
  INTEGER as cmefg100LocFiberAutoNegot  
  CpsConnector as cmefg100LocFiberConnA  
  INTEGER as cmefg100LocFiberDuplex  
  INTEGER as cmefg100LocFiberLink  
  INTEGER as cmefg100LocFiberPause  
  INTEGER as cmefg100LocFiberQosPause  
  INTEGER as cmefg100LocFiberSacEnable  
  INTEGER as cmefg100LocFiberSacStatus  
  INTEGER as cmefg100LocFirmwareRevision  
  INTEGER as cmefg100LocFpgaRev  
  INTEGER as cmefg100LocFxTxBwaKb  
  INTEGER as cmefg100LocFxTxBwaMb  
  INTEGER as cmefg100LocOamActiveMode  
  INTEGER as cmefg100LocOamAdminControl  
  INTEGER as cmefg100LocOamConfigRevision  
  INTEGER as cmefg100LocOamControlInUnknownOpcodes  
  INTEGER as cmefg100LocOamCriticalEvent  
  INTEGER as cmefg100LocOamDuplicateEventNotificationRx  
  INTEGER as cmefg100LocOamFramesLostDueToOamError  
  INTEGER as cmefg100LocOamInformationRx  
  INTEGER as cmefg100LocOamInformationTx  
  INTEGER as cmefg100LocOamLastGasp  
  INTEGER as cmefg100LocOamLinkEvents  
  INTEGER as cmefg100LocOamLinkFault  
  INTEGER as cmefg100LocOamLocDteDisc  
  INTEGER as cmefg100LocOamLoopbackControlRx  
  INTEGER as cmefg100LocOamLoopbackControlTx  
  MacAddress as cmefg100LocOamMacAddress  
  INTEGER as cmefg100LocOamMaxOamPduSize  
  INTEGER as cmefg100LocOamMultiplexorState  
  INTEGER as cmefg100LocOamOperStatus  
  INTEGER as cmefg100LocOamOrgSpecificRx  
  INTEGER as cmefg100LocOamOrgSpecificTx  
  INTEGER as cmefg100LocOamParserState  
  INTEGER as cmefg100LocOamRmtDteDisc  
  INTEGER as cmefg100LocOamRmtLoopback  
  INTEGER as cmefg100LocOamUnidirectional  
  INTEGER as cmefg100LocOamVarRetrieval  
  INTEGER as cmefg100LocSelfTestFailed  
  INTEGER as cmefg100LocSerialNumber  
  INTEGER as cmefg100LocTpAdv1000FDX  
  INTEGER as cmefg100LocTpAdv1000HDX  
  INTEGER as cmefg100LocTpAdv100FDX  
  INTEGER as cmefg100LocTpAdv100HDX  
  INTEGER as cmefg100LocTpAdv10FDX  
  INTEGER as cmefg100LocTpAdv10HDX  
  INTEGER as cmefg100LocTpAutoNegot  
  CpsConnector as cmefg100LocTpConnB  
  INTEGER as cmefg100LocTpCross  
  INTEGER as cmefg100LocTpDuplex  
  INTEGER as cmefg100LocTpLink  
  INTEGER as cmefg100LocTpPause  
  INTEGER as cmefg100LocTpQosPause  
  INTEGER as cmefg100LocTpSacEnable  
  INTEGER as cmefg100LocTpSacStatus  
  INTEGER as cmefg100LocTpSpeed  
  INTEGER as cmefg100LocTxFxBwaKb  
  INTEGER as cmefg100LocTxFxBwaMb  
  TimeTicks as cmefg100LocUptime  
  INTEGER as cmefg100QosHqWeight  
  INTEGER as cmefg100QosLqWeight  
  INTEGER as cmefg100QosPriority  
  INTEGER as cmefg100RmtColdStart  
  INTEGER as cmefg100RmtDetected  
  INTEGER as cmefg100RmtDmiRxPower  
  INTEGER as cmefg100RmtDmiRxPowerAlarm  
  INTEGER as cmefg100RmtDmiTemp  
  INTEGER as cmefg100RmtDmiTempAlarm  
  INTEGER as cmefg100RmtDmiTxBiasAlarm  
  INTEGER as cmefg100RmtDmiTxBiasCurrent  
  INTEGER as cmefg100RmtDmiTxPower  
  INTEGER as cmefg100RmtDmiTxPowerAlarm  
  INTEGER as cmefg100RmtFactoryReset  
  INTEGER as cmefg100RmtFiberAutoNegot  
  INTEGER as cmefg100RmtFiberLink  
  INTEGER as cmefg100RmtFiberPause  
  INTEGER as cmefg100RmtFiberQosPause  
  INTEGER as cmefg100RmtFirmwareRevision  
  INTEGER as cmefg100RmtFpgaRev  
  INTEGER as cmefg100RmtOamActiveMode  
  INTEGER as cmefg100RmtOamCriticalEvent  
  INTEGER as cmefg100RmtOamLastGasp  
  INTEGER as cmefg100RmtOamLinkEvents  
  INTEGER as cmefg100RmtOamLinkFault  
  INTEGER as cmefg100RmtOamLocDteDisc  
  INTEGER as cmefg100RmtOamPeerConfigRevision  
  MacAddress as cmefg100RmtOamPeerMacAddress  
  INTEGER as cmefg100RmtOamPeerMaxOamPduSize  
  INTEGER as cmefg100RmtOamPeerMultiplexorState  
  INTEGER as cmefg100RmtOamPeerParserState  
  OCTET STRING as cmefg100RmtOamPeerVendorInfo  
  OCTET STRING as cmefg100RmtOamPeerVendorOui  
  INTEGER as cmefg100RmtOamRmtDteDisc  
  INTEGER as cmefg100RmtOamRmtLoopback  
  INTEGER as cmefg100RmtOamUnidirectional  
  INTEGER as cmefg100RmtOamVarRetrieval  
  INTEGER as cmefg100RmtSelfTestFailed  
  INTEGER as cmefg100RmtSerialNumber  
  INTEGER as cmefg100RmtTpAdv1000FDX  
  INTEGER as cmefg100RmtTpAdv1000HDX  
  INTEGER as cmefg100RmtTpAdv100FDX  
  INTEGER as cmefg100RmtTpAdv100HDX  
  INTEGER as cmefg100RmtTpAdv10FDX  
  INTEGER as cmefg100RmtTpAdv10HDX  
  INTEGER as cmefg100RmtTpAutoNegot  
  INTEGER as cmefg100RmtTpCross  
  INTEGER as cmefg100RmtTpDuplex  
  INTEGER as cmefg100RmtTpLink  
  INTEGER as cmefg100RmtTpPause  
  INTEGER as cmefg100RmtTpQosPause  
  INTEGER as cmefg100RmtTpSpeed  
  TimeTicks as cmefg100RmtUptime  
  INTEGER as cmefg100VlanCacheCmd  
  INTEGER as cmefg100VlanCacheState  
  INTEGER as cmefg100VlanEditCmd  
  INTEGER as cmefg100VlanEditFwdFiber  
  INTEGER as cmefg100VlanEditFwdTp  
  INTEGER as cmefg100VlanEditUntagFiber  
  INTEGER as cmefg100VlanEditUntagTp  
  INTEGER as cmefg100VlanEditVid  
  INTEGER as cmefg100VlanEnable  
  INTEGER as cmefg100VlanEntries  
  INTEGER as cmefg100VlanFiberDefaultPri  
  INTEGER as cmefg100VlanFiberDefaultVid  
  INTEGER as cmefg100VlanFiberInUntaggedDrop  
  INTEGER as cmefg100VlanFwdFiberTbl  
  INTEGER as cmefg100VlanFwdTpTbl  
  INTEGER as cmefg100VlanIngressVidHitNoMem  
  INTEGER as cmefg100VlanIngressVidMiss  
  INTEGER as cmefg100VlanPriMapTbl  
  INTEGER as cmefg100VlanPriTagCtrl  
  INTEGER as cmefg100VlanSetFailed  
  INTEGER as cmefg100VlanTagIn  
  INTEGER as cmefg100VlanTpDefaultPri  
  INTEGER as cmefg100VlanTpDefaultVid  
  INTEGER as cmefg100VlanTpInUntaggedDrop  
  INTEGER as cmefg100VlanUntagFiberTbl  
  INTEGER as cmefg100VlanUntagTpTbl  
  INTEGER as cmefg100VlanVidTagCtrl  
  INTEGER as cmefg100VlanVidTbl  
  INTEGER as cmefg100CacheClean  

Mcc16SlotEntry  
SEQUENCE    
  INTEGER as mcc16Index  
  OBJECT IDENTIFIER as mcc16DeviceType  

CpsCabinetEntry  
SEQUENCE    
  INTEGER as cpsCabinetBiaIndex  
  OBJECT IDENTIFIER as cpsCabinetModel  
  DisplayString as cpsCabinetDescription  
  INTEGER as cpsCabinetSequence  

CpsMc1800Entry  
SEQUENCE    
  INTEGER as cpsMc1800BiaIndex  
  DisplayString as cpsMc1800Description  
  INTEGER as cpsMc1800PSPower1  
  INTEGER as cpsMc1800PSInUse1  
  INTEGER as cpsMc1800PSPower2  
  INTEGER as cpsMc1800PSInUse2  
  INTEGER as cpsMc1800MRevision  

CpsMc1300Entry  
SEQUENCE    
  INTEGER as cpsMc1300BiaIndex  
  DisplayString as cpsMc1300Description  
  INTEGER as cpsMc1300PSPower1  
  INTEGER as cpsMc1300PSInUse1  
  INTEGER as cpsMc1300PSPower2  
  INTEGER as cpsMc1300PSInUse2  
  INTEGER as cpsMc1300MRevision  

CpsMc0200Entry  
SEQUENCE    
  INTEGER as cpsMc0200BiaIndex  
  DisplayString as cpsMc0200Description  
  INTEGER as cpsMc0200MRevision  

CpsMc1900Entry  
SEQUENCE    
  INTEGER as cpsMc1900BiaIndex  
  DisplayString as cpsMc1900Description  
  INTEGER as cpsMc1900MRevision  

Smacf100Entry  
SEQUENCE    
  INTEGER as smacf100BiaIndex  
  DisplayString as smacf100Description  
  INTEGER as smacf100MRevision  
  INTEGER as smacf100SpanningTree  
  INTEGER as smacf100ResetCounters  
  INTEGER as smacf100SelfTest  
  INTEGER as smacf100QosEnable  
  INTEGER as smacf100QosHPThreshold  
  INTEGER as smacf100QosLqWeight  
  INTEGER as smacf100QosHqWeight  
  INTEGER as smacf100SNMPModuleInstalled  
  INTEGER as smacf100AgingTimer  

CpsMc0800Entry  
SEQUENCE    
  INTEGER as cpsMc0800BiaIndex  
  DisplayString as cpsMc0800Description  
  INTEGER as cpsMc0800MRevision  

CpsSlotPwrEntry  
SEQUENCE    
  INTEGER as cpsSlotPwrBiaIndex  
  INTEGER as cpsSlotPwrSlotIndex  
  INTEGER as cpsSlotPwrState