MICOM-4400-VOICE-NETWORK-MIB

File: MICOM-4400-VOICE-NETWORK-MIB.mib (114876 bytes)

Imported modules

RFC-1215 RFC1155-SMI RFC-1212
RFC1213-MIB MICOM-SYS-MIB MICOM-OSCAR-MIB

Imported symbols

TRAP-TYPE Counter IpAddress
OBJECT-TYPE DisplayString mcmSysAsciiTimeOfDay
micom-oscar

Defined Objects

micom-2vnet 1.3.6.1.4.1.335.1.4.21
OBJECT IDENTIFIER    

vnet-configuration 1.3.6.1.4.1.335.1.4.21.1
OBJECT IDENTIFIER    

mcmVNETDownloadFail 1.3.6.1.4.1.335.1.4.21.1
NAME = ; DESC = Indicates that a failure occurred while \ downloading the voice image.\ Severity Level: MAJOR.; HELP = Downloading the voice image failed. Retry again, and if problem \ persists, please contact system admin., or field \ Personnel.;
TRAP-TYPE    
  mcmSysAsciiTimeOfDay  
  mcmVNETChCfgLimID  
  mcmVNETChCfgChannelID  

mcmVNETChCfgTable 1.3.6.1.4.1.335.1.4.21.1.1
NAME = ; DESC = The VNET Voice Channel Configuration table. \ (Operational); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
OBJECT-TYPE    
  SEQUENCE OF  
    McmVNETChCfgEntry

mcmVNETChCfgEntry 1.3.6.1.4.1.335.1.4.21.1.1.1
NAME = ; DESC = An entry in the VNET Voice Channel Configuration \ table. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  McmVNETChCfgEntry  

mcmVNETChCfgLimID 1.3.6.1.4.1.335.1.4.21.1.1.1.1
NAME = ; DESC = The card lim (logical interface module) number of a \ particular voice channel. Used as an index to the \ VNET Voice Channel Configuration table. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER lim1(2), lim2(3), lim3(4), lim4(5), limB(6), limC(7), limD(8), limE(9)  

mcmVNETChCfgChannelID 1.3.6.1.4.1.335.1.4.21.1.1.1.2
NAME = ; DESC = The position of the voice channel in the lim. \ Used as an index to the VNET Voice \ Channel Configuration table. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..12  

mcmVNETChCfgVoiceProfile 1.3.6.1.4.1.335.1.4.21.1.1.1.3
NAME = ; DESC = The value of this object indicates the profile \ to be used to configure the specified voice \ channel. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..32  

mcmVNETChCfgSwitchingProfile 1.3.6.1.4.1.335.1.4.21.1.1.1.4
NAME = ; DESC = The value of this object indicates the profile \ to be used for a switching call. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..32  

mcmVNETChCfgInterfaceType 1.3.6.1.4.1.335.1.4.21.1.1.1.5
NAME = ; DESC = The value of this object indicates the interface \ type of the specified voice channel. (Operational); HELP = Upon powerup, the interface type will not be \ available until the DSP software is loaded and its \ status is reported.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER not-available(1), enhanced-loop-start-FXS(2), enhanced-EandM(3), enhanced-loop-start-FXO(4), low-cost-loop-start-FXS(5), low-cost-EandM(6), low-cost-loop-start-FXO(7), ground-start-FXS(8), ground-start-FXO(9), three-port(10), dvm(11), bri(12)  

mcmVNETProfileCfgTable 1.3.6.1.4.1.335.1.4.21.1.2
NAME = ; DESC = The VNET Voice Profile Configuration table. \ (Operational); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
OBJECT-TYPE    
  SEQUENCE OF  
    McmVNETProfileCfgEntry

mcmVNETProfileCfgEntry 1.3.6.1.4.1.335.1.4.21.1.2.1
NAME = ; DESC = An entry in the VNET Voice Profile Configuration \ table. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  McmVNETProfileCfgEntry  

mcmVNETProfileCfgProfileNum 1.3.6.1.4.1.335.1.4.21.1.2.1.1
NAME = ; DESC = The value of this object indicates the profile \ number. Used as an index to the VNET Voice \ Profile Configuration table. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..32  

mcmVNETProfileCfgMode 1.3.6.1.4.1.335.1.4.21.1.2.1.2
NAME = ; DESC = The value of this object selects the voice \ channel signal processing. (Operational); HELP = Can be used to set to either dual mode with \ both voice and fax, or just voice.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER voiceFax(1), voiceOnly(2)  

mcmVNETProfileCfgDigitizingRate 1.3.6.1.4.1.335.1.4.21.1.2.1.3
NAME = ; DESC = The value of this object selects the voice \ digitizing algorithm. (Operational); HELP = Rate at which voice is digitized in \ designated in bits per second.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER rateG729(1), rateG729-8K-40MS(2)  

mcmVNETProfileCfgInputLevelGain 1.3.6.1.4.1.335.1.4.21.1.2.1.4
NAME = ; DESC = The value of this object selects the input \ signal gain in dB. (Operational); HELP = For DVM, max value is 8 dB. If more than \ 8 dB is configured, 8 dB will be used. \ The range for the BRI card is -15 to 15 dB.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER -15..19  

mcmVNETProfileCfgOutputLevelAttn 1.3.6.1.4.1.335.1.4.21.1.2.1.5
NAME = ; DESC = The value of this object selects the output \ signal attenuation in dB. (Operational); HELP = For DVM, max value is 8 dB. If more than \ 8 dB is configured, 8 dB will be used. \ The range for the BRI card is -15 to 15dB.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER -15..25  

mcmVNETProfileCfgBusyOutMode 1.3.6.1.4.1.335.1.4.21.1.2.1.6
NAME = ; DESC = The value of this object selects the voice \ channel busy out control type. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER systemControlled(1), forceOn(2), forceOff(3)  

mcmVNETProfileCfgBandwidth 1.3.6.1.4.1.335.1.4.21.1.2.1.7
NAME = ; DESC = The value of this object selects the voice \ channel link bandwidth reservation style. \ (Operational); HELP = 2 is used for forced connects or PVCs only. \ 1 is used for switched connects.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER voiceActivated(1), continuous(2)  

mcmVNETProfileCfgBackground 1.3.6.1.4.1.335.1.4.21.1.2.1.8
NAME = ; DESC = The value of this object selects the voice \ channel background noise generation type. \ (Operational); HELP = The ability of passing background noise or \ silencing the channel during idle periods. \ First option allows the background noise to be \ regenerated during the periods, whereas the \ second option suppresses background noise during \ idle periods.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER regenerated(1), silence(2)  

mcmVNETProfileCfgBRIPulseRate 1.3.6.1.4.1.335.1.4.21.1.2.1.9
NAME = ; DESC = The value of this object selects the voice \ channel pulse rate in pulses per second. \ (Operational); HELP = NOTE: This object is used by the Partner card \ and not for the ISDN BRI voice card.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER pulses10PerSec(1), pulses20PerSec(2), pulses125PerSec(3)  

mcmVNETProfileCfgEMSigFormat 1.3.6.1.4.1.335.1.4.21.1.2.1.10
NAME = ; DESC = The value of this object specifies the voice \ channel E&M signaling format. (Operational); HELP = 2 and 3 are used for force connects only. \ 1 (DC) is used for switched connects.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER dc(1), tone2280(2), pulsedDC(3), winkStart(4)  

mcmVNETProfileCfgFXSSigFormat 1.3.6.1.4.1.335.1.4.21.1.2.1.11
NAME = ; DESC = The value of this object specifies the voice \ channel FXS signaling format. (Operational); HELP = 1 is used for force connects only. \ 2 is used for switched connects.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER repeatedRing(1), interruptedRing(2)  

mcmVNETProfileCfgDVMSigFormat 1.3.6.1.4.1.335.1.4.21.1.2.1.12
NAME = ; DESC = The value of this object specifies the voice \ channel DVM signaling format. (Operational); HELP = 3 and 4 are used for force connects only. \ 1 is used for switched connects.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER tieTrunk(1), tieInvert(2), tone2280(3), clearChannel(4), dC5B(5), dC5BInvert(6), r2PUNCOM(7), r2Q421(8), dC5RonTron(9), israelCAS(10), spainCAS(11), winkStart(12)  

mcmVNETProfileCfgNumberOfRings 1.3.6.1.4.1.335.1.4.21.1.2.1.13
NAME = ; DESC = The value of this object specifies when the \ voice channel (FXO or 3-port) will answer \ the call request. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..9  

mcmVNETProfileCfgEMAnalOper 1.3.6.1.4.1.335.1.4.21.1.2.1.14
NAME = ; DESC = The value of this object specifies the E&M \ voice channel operation as either 2 or 4 wire \ operation. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER twoWire(1), fourWire(2)  

mcmVNETProfileCfgRingingFreq 1.3.6.1.4.1.335.1.4.21.1.2.1.15
NAME = ; DESC = The value of this object specifies the voice \ channel (FXS or 3-port) ringing frequency. \ (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER freq25Hz(1), freq50Hz(2)  

mcmVNETProfileCfgFaxDigRate 1.3.6.1.4.1.335.1.4.21.1.2.1.16
NAME = ; DESC = The value of this object selects the voice \ channel Fax digitizing rate in bits per second. \ (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER voiceRate(1), rate2400(2), rate4800(3), rate7200(4), rate9600(5)  

mcmVNETProfileCfgDiscSupervision 1.3.6.1.4.1.335.1.4.21.1.2.1.17
NAME = ; DESC = The value of this object selects the voice \ channel method to detect the line disconnect. \ (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER tone(1), powerInterrupt(2)  

mcmVNETProfileCfgLineImpedance 1.3.6.1.4.1.335.1.4.21.1.2.1.18
NAME = ; DESC = The value of this object selects the voice \ channel type of line impedance. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER impedance600Ohms(1), complex(2)  

mcmVNETProfileCfgMaxOutputLevel 1.3.6.1.4.1.335.1.4.21.1.2.1.19
NAME = ; DESC = The value of this object specifies the voice \ channel maximum output level. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER zerodBMNominal(1), plus7dBM(2)  

mcmVNETProfileCfgRegenDelay 1.3.6.1.4.1.335.1.4.21.1.2.1.20
NAME = ; DESC = The value of this object specifies the voice \ channel time (in seconds) to delay before dialing \ out the number (i.e., time to wait for dial tone). \ (Operational); HELP = NOTE: This object is not required for the ISDN BRI \ voice card; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..15  

mcmVNETProfileCfgDialDigTimeLimit 1.3.6.1.4.1.335.1.4.21.1.2.1.21
NAME = ; DESC = The value of this object specifies the voice \ channel inter-digit time-out time (in seconds). \ (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..15  

mcmVNETProfileCfgMaxNumForDig 1.3.6.1.4.1.335.1.4.21.1.2.1.22
NAME = ; DESC = The value of this object specifies the voice \ channel maximum number of digits that can \ be dialed. (Operational); HELP = 0 is used for auto-call functionality.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..40  

mcmVNETProfileCfgRegenFormat 1.3.6.1.4.1.335.1.4.21.1.2.1.23
NAME = ; DESC = The value of this object specifies the voice \ channel dial digit regeneration format. \ (Operational); HELP = NOTE: This object is not required for the ISDN \ BRI voice card.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER dialPulse(1), dtmf(2)  

mcmVNETProfileCfgCallProgTone 1.3.6.1.4.1.335.1.4.21.1.2.1.24
NAME = ; DESC = The value of this object specifies the voice \ channel call progress tone required for different \ countries or areas. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER northAmerica(1), japan(2), unitedKingdom(3), europe(4), france(5), centralAmerica(6), chile(7), australia(8)  

mcmVNETProfileCfgDTMFDetector 1.3.6.1.4.1.335.1.4.21.1.2.1.25
NAME = ; DESC = The value of this object specifies to the voice \ channel whether to turn on or off the DTMF \ detector. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

mcmVNETProfileCfgJitters 1.3.6.1.4.1.335.1.4.21.1.2.1.26
NAME = ; DESC = The value of this object specifies the voice \ channel maximum jitters delay (in milliseconds). \ (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..200  

mcmVNETProfileCfgEchoCanceller 1.3.6.1.4.1.335.1.4.21.1.2.1.27
NAME = ; DESC = The value of this object specifies to the voice \ channel whether to turn on or off the echo \ canceller. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

mcmVNETProfileCfgAutoGainControl 1.3.6.1.4.1.335.1.4.21.1.2.1.28
NAME = ; DESC = The value of this object specifies to the voice \ channel whether to automatically set the input \ signal level. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

mcmVNETProfileCfgCompanderFormat 1.3.6.1.4.1.335.1.4.21.1.2.1.29
NAME = ; DESC = The value of this object specifies the voice \ channel (DVM or BRI) compander type. \ (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER uLaw(1), aLaw(2)  

mcmVNETProfileCfgPremiumVoice 1.3.6.1.4.1.335.1.4.21.1.2.1.30
NAME = ; DESC = The value of this object specifies to the voice \ channel (DVM) whether to enable or disable the \ transparent voice (no compression) algorithm. \ (Operational); HELP = This object is also used by the ISDN BRI voice card \ to enable/disable Digital Lossless Switching Pattern \ Generation and Pattern Search.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER disable-compress(1), enable-notcompress(2)  

mcmVNETProfileCfgEndOfDialChar 1.3.6.1.4.1.335.1.4.21.1.2.1.31
NAME = ; DESC = The value of this object specifies to the voice \ channel whether '#' is used to end a dialing input. \ (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

mcmVNETProfileCfgBckGrndNoiseLevel 1.3.6.1.4.1.335.1.4.21.1.2.1.32
NAME = ; DESC = Signal input above this level is considered\ a voiced signal, below this level, the \ Voice Activity Detector (VAD), will \ determine if it is a voiced signal or \ background noise. (Operational); HELP = Refer to the International \ Telecommunication Union(ITU-T) G.711 \ document for more information; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER neg25dbm0(1), neg30dbm0(2), neg35dbm0(3), neg40dbm0(4), neg45dbm0(5)  

mcmVNETProfileCfgSilenceHngOvrTime 1.3.6.1.4.1.335.1.4.21.1.2.1.33
NAME = ; DESC = Indicates the time delay to switch \ from voice to silence.\ (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER msec100(1), msec200(2), msec300(3), msec400(4), msec500(5), msec600(6), msec700(7), msec800(8)  

mcmVNETProfileCfgIdlePattern 1.3.6.1.4.1.335.1.4.21.1.2.1.34
NAME = ; DESC = The value of this object represents the \ Idle pattern on the line when no call is up.\ Specific to a PBX. This is a permanent DSP \ configuration parameter; HELP = This value can be used to detect that a call \ has finished and that the echo canceller should \ be reset and that fax mode should be terminated.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..255  

mcmVNETProfileCfgEcanFilterLength 1.3.6.1.4.1.335.1.4.21.1.2.1.35
NAME = ; DESC = The value of this object specifies the filter \ length for echo canceller. This is a permanent \ DSP configuration parameter.; HELP = A length of 128 is equal to 16ms.\ A length of 256 is equal to 32ms.; -- NOTE: The ISDN BRI voice card supports 32ms only; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER length128(1), length256(2)  

mcmVNETProfileCfgEcanErlImprovement 1.3.6.1.4.1.335.1.4.21.1.2.1.36
NAME = ; DESC = The value of this object is used for echo \ canceller Er1 improvement. This is a DSP \ Dynamic configuration parameter. \ A signal will be attenuated by this dB \ amount before being passed through the \ echo canceller. After the echo canceller, \ it will be amplified by this same dB amount, \ for a net gain of 0 dB. \ This attenuation amplicfication cycle reduces \ the resolution of the signal ( -18 ..0 ).; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER -18..0  

mcmVNETProfileCfgNoiseFloorOffset 1.3.6.1.4.1.335.1.4.21.1.2.1.37
NAME = ; DESC = The value of this object will suppress the \ impulsive backround noise in order to achieve \ silence suppression savings. HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..255  

mcmVNETProfileCfgDtmfGenBurstLength 1.3.6.1.4.1.335.1.4.21.1.2.1.38
NAME = ; DESC = DTMF burst generation in milliseconds.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER time50msec(1), time60msec(2), time70msec(3), time100msec(4)  

mcmVNETProfileCfgDtmRegenBurstLength 1.3.6.1.4.1.335.1.4.21.1.2.1.39
NAME = ; DESC = DTMF burst Regeneration length in milliseconds.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER time50msec(1), time60msec(2), time70msec(3), time100msec(4)  

mcmVNETSwProfCfgTable 1.3.6.1.4.1.335.1.4.21.1.3
NAME = ; DESC = The VNET Voice Switching Profile Configuration \ table.(Operational); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
OBJECT-TYPE    
  SEQUENCE OF  
    McmVNETSwProfCfgEntry

mcmVNETSwProfCfgEntry 1.3.6.1.4.1.335.1.4.21.1.3.1
NAME = ; DESC = An entry in the VNET Voice Switching Profile \ Configuration table. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  McmVNETSwProfCfgEntry  

mcmVNETSwProfCfgProfileNum 1.3.6.1.4.1.335.1.4.21.1.3.1.1
NAME = ; DESC = The value of this object indicates the profile \ number. Used as an index to the VNET Voice \ Switching Profile Configuration table. \ (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..32  

mcmVNETSwProfCfgOutCallRestrict 1.3.6.1.4.1.335.1.4.21.1.3.1.2
NAME = ; DESC = The value of this object specifies how to \ handle outgoing calls for voice channel \ switching. (Operational); HELP = 2: include CUG ID in outgoing call. \ 3: include restriction class in outgoing call. \ 4: include both CUG ID and restriction \ class in outgoing call. \ 5: outgoing call is not allowed.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER noRestriction(1), closedUserGroupCall(2), restrictionClassCall(3), bothCUGandRCCall(4), inhibitAll(5)  

mcmVNETSwProfCfgInCallRestrict 1.3.6.1.4.1.335.1.4.21.1.3.1.3
NAME = ; DESC = The value of this object specifies how to \ handle incoming calls for voice channel \ switching. (Operational); HELP = 2: check CUG ID in incoming call. (Must \ match our CUG ID for call acceptance. \ 3: check RCC in incoming call. (Must be \ greater than or equal to our RCC for call \ acceptance. \ 4: check both CUG and RCC in incoming \ call. \ 5: incoming call is not allowed.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER noRestriction(1), checkCUGID(2), checkRestrictionClassCode(3), cUGandPublicClassInhibit(4), inhibitAll(5)  

mcmVNETSwProfCfgCUGID 1.3.6.1.4.1.335.1.4.21.1.3.1.4
NAME = ; DESC = The value of this object assigns the Closed \ User Group ID for a voice channel. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..255  

mcmVNETSwProfCfgRestrictClassCd 1.3.6.1.4.1.335.1.4.21.1.3.1.5
NAME = ; DESC = The value of this object assigns the Restriction \ Class Code for a voice channel. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..255  

mcmVNETSwProfCfgAutoCallEntNum 1.3.6.1.4.1.335.1.4.21.1.3.1.6
NAME = ; DESC = The value of this object provides a voice \ channel Auto Call destination number by \ specifying an index into the ingress table. \ (Operational); HELP = 0: auto call disabled. \ 1-32: index to the ingress table entry where \ the dial number is specified. \ The auto call for the ISDN BRI voice card is \ always disabled.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..32  

mcmVNETSwProfCfgCallNegStrategy 1.3.6.1.4.1.335.1.4.21.1.3.1.7
NAME = ; DESC = The value of this object specifies the preference \ for the voice algorithm when an outgoing call is \ made. (Operational); HELP = specific: whatever is configured. \ bandwidth: bigger block size. \ delay: shorter block size.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER specific(1), bandwidth(2), delay(3)  

mcmVNETSwProfCfgTransmitPriority 1.3.6.1.4.1.335.1.4.21.1.3.1.8
NAME = ; DESC = The value of this object assigns the priority \ of the voice data to be transmitted. (Operational); HELP = 0: lowest priority. \ 15: highest priority.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..15  

mcmVNETSwProfCfgAutoCallType 1.3.6.1.4.1.335.1.4.21.1.3.1.9
NAME = ; DESC = Indicates the type of auto-call \ switching to be performed by the \ voice channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER normal(1), masterHootnHoller(2), slaveHootnHoller(3)  

mcmVNETSwProfCfgAddServerSelect 1.3.6.1.4.1.335.1.4.21.1.3.1.10
NAME = ; DESC = Indicates which DNA server is used.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER nas(1), vncs(2)  

mcmVNETSwProfCfgOutCallMode 1.3.6.1.4.1.335.1.4.21.1.3.1.11
NAME = ; DESC = Indicates the type of call being made.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER enblock-only(1), dynamic(2)  

mcmVNETIngressDigFilterTable 1.3.6.1.4.1.335.1.4.21.1.4
NAME = ; DESC = The VNET Voice Ingress Digit Filtering \ Configuration table. (Operational); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
OBJECT-TYPE    
  SEQUENCE OF  
    McmVNETIngressDigFilterEntry

mcmVNETIngressDigFilterEntry 1.3.6.1.4.1.335.1.4.21.1.4.1
NAME = ; DESC = An entry in the VNET Voice Ingress Digit \ Filtering Configuration table. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  McmVNETIngressDigFilterEntry  

mcmVNETIngressDigFilterIndex 1.3.6.1.4.1.335.1.4.21.1.4.1.1
NAME = ; DESC = The value of this object indicates the index to \ the ingress table. Used as an index to the VNET \ Voice Ingress Digit Filtering Configuration table. \ Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..32  

mcmVNETIngressDigFilterIngressNum 1.3.6.1.4.1.335.1.4.21.1.4.1.2
NAME = ; DESC = The value of this object selects the digit \ pattern to be matched. (Null terminated \ character string.) (Operational); HELP = Valid characters are decimal digits, '#', \ '*', '+', '[' and ']' .; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

mcmVNETIngressDigFilterManipString 1.3.6.1.4.1.335.1.4.21.1.4.1.3
NAME = ; DESC = The value of this object selects commands \ to produce the ingress digits for speed dial, \ call redirect, and source ID insertion features. \ (Operational); HELP = Valid characters are decimal digits, '#', \ '*', 'D', and 'I'.; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

mcmVNETEgressDigManipTable 1.3.6.1.4.1.335.1.4.21.1.5
NAME = ; DESC = The VNET Voice Egress Digit Manipulation \ Configuration table. (Operational); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
OBJECT-TYPE    
  SEQUENCE OF  
    McmVNETEgressDigManipEntry

mcmVNETEgressDigManipEntry 1.3.6.1.4.1.335.1.4.21.1.5.1
NAME = ; DESC = An entry in the VNET Voice Egress Digit \ Manipulation Configuration table. (Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  McmVNETEgressDigManipEntry  

mcmVNETEgressDigManipIndex 1.3.6.1.4.1.335.1.4.21.1.5.1.1
NAME = ; DESC = The value of this object indicates the index to \ the egress table. Used as an index to the VNET \ Voice Egress Digit Manipulation Configuration \ table. Operational); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..32  

mcmVNETEgressDigManipPhoneNum 1.3.6.1.4.1.335.1.4.21.1.5.1.2
NAME = ; DESC = The value of this object selects the phone \ number that voice channels are associated with. \ This is the number to be registered to the Address \ Server (RSA). (Operational); HELP = Valid characters are decimal digits, '#', and '*'.; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

mcmVNETEgressDigManipString 1.3.6.1.4.1.335.1.4.21.1.5.1.3
NAME = ; DESC = The value of this object selects commands \ to produce the egress digits for FXO, E&M, \ or FXS 3-Port interface. The result is the \ number to be sent to the connected phone \ device. (Operational); HELP = Valid characters are decimal digits, '#', '*', \ '+', 'D', 'H', and 'I'. The character 'H' is used \ used to trigger immediate dial handling by the PBX.; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

mcmVNETEgressDigManipChIDList 1.3.6.1.4.1.335.1.4.21.1.5.1.4
NAME = ; DESC = The value of this object selects voice channels \ associated with the phone number. The valid \ string consists of the substring 'B1'~'B6', \ 'C1'~'C12', 'D1'~'D12', and 'E1'~'E2'. \ (Operational); HELP = Valid characters are decimal digits, 'B', 'C', \ 'D', and 'E'.; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..70)  

nvmVNETChCfgTable 1.3.6.1.4.1.335.1.4.21.1.6
NAME = ; DESC = The VNET Voice Channel Configuration table. \ (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
OBJECT-TYPE    
  SEQUENCE OF  
    NvmVNETChCfgEntry

nvmVNETChCfgEntry 1.3.6.1.4.1.335.1.4.21.1.6.1
NAME = ; DESC = An entry in the VNET Voice Channel Configuration \ table. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  NvmVNETChCfgEntry  

nvmVNETChCfgLimID 1.3.6.1.4.1.335.1.4.21.1.6.1.1
NAME = ; DESC = The card lim (logical interface module) number of a \ particular voice channel. Used as an index to the \ VNET Voice Channel Configuration table. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER lim1(2), lim2(3), lim3(4), lim4(5), limB(6), limC(7), limD(8), limE(9)  

nvmVNETChCfgChannelID 1.3.6.1.4.1.335.1.4.21.1.6.1.2
NAME = ; DESC = The position of the voice channel in the lim. \ Used as an index to the VNET Voice \ Channel Configuration table. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..12  

nvmVNETChCfgVoiceProfile 1.3.6.1.4.1.335.1.4.21.1.6.1.3
NAME = ; DESC = The value of this object indicates the profile \ to be used to configure the specified voice \ channel. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..32  

nvmVNETChCfgSwitchingProfile 1.3.6.1.4.1.335.1.4.21.1.6.1.4
NAME = ; DESC = The value of this object indicates the profile \ to be used for a switching call. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..32  

nvmVNETChCfgInterfaceType 1.3.6.1.4.1.335.1.4.21.1.6.1.5
NAME = ; DESC = The value of this object indicates the interface \ type of the specified voice channel. (Configuration); HELP = Upon powerup, the interface type will not be \ available until the DSP software is loaded and its \ status is reported.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER not-available(1), enhanced-loop-start-FXS(2), enhanced-EandM(3), enhanced-loop-start-FXO(4), low-cost-loop-start-FXS(5), low-cost-EandM(6), low-cost-loop-start-FXO(7), ground-start-FXS(8), ground-start-FXO(9), three-port(10), dvm(11), bri(12)  

nvmVNETProfileCfgTable 1.3.6.1.4.1.335.1.4.21.1.7
NAME = ; DESC = The VNET Voice Profile Configuration table. \ (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
OBJECT-TYPE    
  SEQUENCE OF  
    NvmVNETProfileCfgEntry

nvmVNETProfileCfgEntry 1.3.6.1.4.1.335.1.4.21.1.7.1
NAME = ; DESC = An entry in the VNET Voice Profile Configuration \ table. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  NvmVNETProfileCfgEntry  

nvmVNETProfileCfgProfileNum 1.3.6.1.4.1.335.1.4.21.1.7.1.1
NAME = ; DESC = The value of this object indicates the profile \ number. Used as an index to the VNET Voice \ Profile Configuration table. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..32  

nvmVNETProfileCfgMode 1.3.6.1.4.1.335.1.4.21.1.7.1.2
NAME = ; DESC = The value of this object selects the voice \ channel signal processing. (Configuration); HELP = Can be used to set to either dual mode with \ both voice and fax, or just voice.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER voiceFax(1), voiceOnly(2)  

nvmVNETProfileCfgDigitizingRate 1.3.6.1.4.1.335.1.4.21.1.7.1.3
NAME = ; DESC = The value of this object selects the voice \ digitizing algorithm. (Configuration); HELP = Rate at which voice is digitized in \ designated in bits per second.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER rateG729(1), rateG729-8k-40ms(2)  

nvmVNETProfileCfgInputLevelGain 1.3.6.1.4.1.335.1.4.21.1.7.1.4
NAME = ; DESC = The value of this object selects the input \ signal gain in dB. (Configuration); HELP = For DVM, max value is 8 dB. If more than \ 8 dB is configured, 8 dB will be used.\ The ISDN BRI voice card range is -15 to 15dB.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER -15..19  

nvmVNETProfileCfgOutputLevelAttn 1.3.6.1.4.1.335.1.4.21.1.7.1.5
NAME = ; DESC = The value of this object selects the output \ signal attenuation in dB. (Configuration); HELP = For DVM, max value is 8 dB. If more than \ 8 dB is configured, 8 dB will be used.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER -15..25  

nvmVNETProfileCfgBusyOutMode 1.3.6.1.4.1.335.1.4.21.1.7.1.6
NAME = ; DESC = The value of this object selects the voice \ channel busy out control type. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER systemControlled(1), forceOn(2), forceOff(3)  

nvmVNETProfileCfgBandwidth 1.3.6.1.4.1.335.1.4.21.1.7.1.7
NAME = ; DESC = The value of this object selects the voice \ channel link bandwidth reservation style. \ (Configuration); HELP = 2 is used for forced connects or PVCs only. \ 1 is used for switched connects.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER voiceActivated(1), continuous(2)  

nvmVNETProfileCfgBackground 1.3.6.1.4.1.335.1.4.21.1.7.1.8
NAME = ; DESC = The value of this object selects the voice \ channel background noise generation type. \ (Configuration); HELP = The ability of passing background noise or \ silencing the channel during idle periods. \ First option allows the background noise to be \ regenerated during the periods, whereas the \ second option suppresses background noise during \ idle periods.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER regenerated(1), silence(2)  

nvmVNETProfileCfgBRIPulseRate 1.3.6.1.4.1.335.1.4.21.1.7.1.9
NAME = ; DESC = The value of this object selects the voice \ channel pulse rate in pulses per second. \ (Configuration); HELP = NOTE: This object is used by the Partner Card, \ not by the ISDN BRI voice card.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER pulses10PerSec(1), pulses20PerSec(2), pulses125PerSec(3)  

nvmVNETProfileCfgEMSigFormat 1.3.6.1.4.1.335.1.4.21.1.7.1.10
NAME = ; DESC = The value of this object specifies the voice \ channel E&M signaling format. (Configuration); HELP = 2 and 3 are used for force connects only. \ 1 (DC) is used for switched connects.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER dc(1), tone2280(2), pulsedDC(3), winkStart(4)  

nvmVNETProfileCfgFXSSigFormat 1.3.6.1.4.1.335.1.4.21.1.7.1.11
NAME = ; DESC = The value of this object specifies the voice \ channel FXS signaling format. (Configuration); HELP = 1 is used for force connects only. \ 2 is used for switched connects.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER repeatedRing(1), interruptedRing(2)  

nvmVNETProfileCfgDVMSigFormat 1.3.6.1.4.1.335.1.4.21.1.7.1.12
NAME = ; DESC = The value of this object specifies the voice \ channel DVM signaling format. (Configuration); HELP = 3 and 4 are used for force connects only. \ 1 is used for switched connects.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER tieTrunk(1), tieInvert(2), tone2280(3), clearChannel(4), dC5B(5), dC5BInvert(6), r2PUNCOM(7), r2Q421(8), dC5RonTron(9), israelCAS(10), spainCAS(11), winkStart(12)  

nvmVNETProfileCfgNumberOfRings 1.3.6.1.4.1.335.1.4.21.1.7.1.13
NAME = ; DESC = The value of this object specifies when the \ voice channel (FXO or 3-port) will answer \ the call request. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..9  

nvmVNETProfileCfgEMAnalOper 1.3.6.1.4.1.335.1.4.21.1.7.1.14
NAME = ; DESC = The value of this object specifies the E&M \ voice channel operation as either 2 or 4 wire \ operation. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER twoWire(1), fourWire(2)  

nvmVNETProfileCfgRingingFreq 1.3.6.1.4.1.335.1.4.21.1.7.1.15
NAME = ; DESC = The value of this object specifies the voice \ channel (FXS or 3-port) ringing frequency. \ (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER freq25Hz(1), freq50Hz(2)  

nvmVNETProfileCfgFaxDigRate 1.3.6.1.4.1.335.1.4.21.1.7.1.16
NAME = ; DESC = The value of this object selects the voice \ channel Fax digitizing rate in bits per second. \ (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER voiceRate(1), rate2400(2), rate4800(3), rate7200(4), rate9600(5)  

nvmVNETProfileCfgDiscSupervision 1.3.6.1.4.1.335.1.4.21.1.7.1.17
NAME = ; DESC = The value of this object selects the voice \ channel method to detect the line disconnect. \ (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER tone(1), powerInterrupt(2)  

nvmVNETProfileCfgLineImpedance 1.3.6.1.4.1.335.1.4.21.1.7.1.18
NAME = ; DESC = The value of this object selects the voice \ channel type of line impedance. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER impedance600Ohms(1), complex(2)  

nvmVNETProfileCfgMaxOutputLevel 1.3.6.1.4.1.335.1.4.21.1.7.1.19
NAME = ; DESC = The value of this object specifies the voice \ channel maximum output level. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER zerodBMNominal(1), plus7dBM(2)  

nvmVNETProfileCfgRegenDelay 1.3.6.1.4.1.335.1.4.21.1.7.1.20
NAME = ; DESC = The value of this object specifies the voice \ channel time (in seconds) to delay before dialing \ out the number (i.e., time to wait for dial tone). \ (Configuration); HELP = NOTE : This object is not used for the ISDN BRI \ voice card.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..15  

nvmVNETProfileCfgDialDigTimeLimit 1.3.6.1.4.1.335.1.4.21.1.7.1.21
NAME = ; DESC = The value of this object specifies the voice \ channel inter-digit time-out time (in seconds). \ (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..15  

nvmVNETProfileCfgMaxNumForDig 1.3.6.1.4.1.335.1.4.21.1.7.1.22
NAME = ; DESC = The value of this object specifies the voice \ channel maximum number of digits that can \ be dialed. (Configuration); HELP = 0 is used for auto-call functionality.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..40  

nvmVNETProfileCfgRegenFormat 1.3.6.1.4.1.335.1.4.21.1.7.1.23
NAME = ; DESC = The value of this object specifies the voice \ channel dial digit regeneration format. \ (Configuration); HELP = NOTE: THIS object is not used for the ISDN \ BRI voice card.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER dialPulse(1), dtmf(2)  

nvmVNETProfileCfgCallProgTone 1.3.6.1.4.1.335.1.4.21.1.7.1.24
NAME = ; DESC = The value of this object specifies the voice \ channel call progress tone required for different \ countries or areas. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER northAmerica(1), japan(2), unitedKingdom(3), europe-germany(4), france(5), centralAmerica(6), chile(7), australia(8)  

nvmVNETProfileCfgDTMFDetector 1.3.6.1.4.1.335.1.4.21.1.7.1.25
NAME = ; DESC = The value of this object specifies to the voice \ channel whether to turn on or off the DTMF \ detector. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

nvmVNETProfileCfgJitters 1.3.6.1.4.1.335.1.4.21.1.7.1.26
NAME = ; DESC = The value of this object specifies the voice \ channel maximum jitters delay (in milliseconds). \ (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..200  

nvmVNETProfileCfgEchoCanceller 1.3.6.1.4.1.335.1.4.21.1.7.1.27
NAME = ; DESC = The value of this object specifies to the voice \ channel whether to turn on or off the echo \ canceller. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

nvmVNETProfileCfgAutoGainControl 1.3.6.1.4.1.335.1.4.21.1.7.1.28
NAME = ; DESC = The value of this object specifies to the voice \ channel whether to automatically set the input \ signal level. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

nvmVNETProfileCfgCompanderFormat 1.3.6.1.4.1.335.1.4.21.1.7.1.29
NAME = ; DESC = The value of this object specifies the voice \ channel (DVM or BRI) compander type. \ (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER uLaw(1), aLaw(2)  

nvmVNETProfileCfgPremiumVoice 1.3.6.1.4.1.335.1.4.21.1.7.1.30
NAME = ; DESC = The value of this object specifies to the voice \ channel (DVM) whether to enable or disable the \ transparent voice (no compression) algorithm. \ (Configuration); HELP = This object is also used by the ISDN BRI voice \ card to enable/disable Digital Lossless Switching \ Pattern Generation and Pattern Search.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER disable-compress(1), enable-notcompress(2)  

nvmVNETProfileCfgEndOfDialChar 1.3.6.1.4.1.335.1.4.21.1.7.1.31
NAME = ; DESC = The value of this object specifies to the voice \ channel whether '#' is used to end a dialing input. \ (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

nvmVNETProfileCfgBckGrndNoiseLevel 1.3.6.1.4.1.335.1.4.21.1.7.1.32
NAME = ; DESC = Signal input above this level is considered\ a voiced signal, below this level, the \ Voice Activity Detector (VAD), will \ determine if it is a voiced signal or \ background noise. (Configuration); HELP = Refer to the International \ Telecommunication Union(ITU-T) G.711 \ document for more information; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER neg25dbm0(1), neg30dbm0(2), neg35dbm0(3), neg40dbm0(4), neg45dbm0(5)  

nvmVNETProfileCfgSilenceHngOvrTime 1.3.6.1.4.1.335.1.4.21.1.7.1.33
NAME = ; DESC = Indicates the time delay to switch \ from voice to silence.\ (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER msec100(1), msec200(2), msec300(3), msec400(4), msec500(5), msec600(6), msec700(7), msec800(8)  

nvmVNETProfileCfgIdlePattern 1.3.6.1.4.1.335.1.4.21.1.7.1.34
NAME = ; DESC = The value of this object represents the \ Idle pattern on the line when no call is up.\ Specific to a PBX. This is a permanent DSP \ configuration parameter; HELP = This value can be used to detect that a call \ has finished and that the echo canceller should \ be reset and that fax mode should be terminated.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..255  

nvmVNETProfileCfgEcanFilterLength 1.3.6.1.4.1.335.1.4.21.1.7.1.35
NAME = ; DESC = The value of this object specifies the filter \ length for echo canceller. This is a permanent \ DSP configuration parameter.; HELP = A length of 128 is equal to 16ms.\ A length of 256 is equal to 32ms.; ---- NOTE: The ISDN BRI voice card supports 32ms only; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER length128(1), length256(2)  

nvmVNETProfileCfgEcanErlImprovement 1.3.6.1.4.1.335.1.4.21.1.7.1.36
NAME = ; DESC = The value of this object is used for echo \ canceller Er1 improvement. This is a DSP \ Dynamic configuration parameter. \ A signal will be attenuated by this dB \ amount before being passed through the \ echo canceller. After the echo canceller, \ it will be amplified by this same dB amount, \ for a net gain of 0 dB. \ This attenuation amplicfication cycle reduces \ the resolution of the signal ( -18 ..0 ).; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER -18..0  

nvmVNETProfileCfgNoiseFloorOffset 1.3.6.1.4.1.335.1.4.21.1.7.1.37
NAME = ; DESC = The value of this object will suppress the \ impulsive backround noise in order to achieve \ silence suppression savings. HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..255  

nvmVNETProfileCfgDtmfGenBurstLength 1.3.6.1.4.1.335.1.4.21.1.7.1.38
NAME = ; DESC = DTMF burst generation in milliseconds.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER time50msec(1), time60msec(2), time70msec(3), time100msec(4)  

nvmVNETProfileCfgDtmRegenBurstLength 1.3.6.1.4.1.335.1.4.21.1.7.1.39
NAME = ; DESC = DTMF burst Regeneration length in milliseconds.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER time50msec(1), time60msec(2), time70msec(3), time100msec(4)  

nvmVNETSwProfCfgTable 1.3.6.1.4.1.335.1.4.21.1.8
NAME = ; DESC = The VNET Voice Switching Profile Configuration \ table.(Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
OBJECT-TYPE    
  SEQUENCE OF  
    NvmVNETSwProfCfgEntry

nvmVNETSwProfCfgEntry 1.3.6.1.4.1.335.1.4.21.1.8.1
NAME = ; DESC = An entry in the VNET Voice Switching Profile \ Configuration table. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  NvmVNETSwProfCfgEntry  

nvmVNETSwProfCfgProfileNum 1.3.6.1.4.1.335.1.4.21.1.8.1.1
NAME = ; DESC = The value of this object indicates the profile \ number. Used as an index to the VNET Voice \ Switching Profile Configuration table. \ (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..32  

nvmVNETSwProfCfgOutCallRestrict 1.3.6.1.4.1.335.1.4.21.1.8.1.2
NAME = ; DESC = The value of this object specifies how to \ handle outgoing calls for voice channel \ switching. (Configuration); HELP = 2: include CUG ID in outgoing call. \ 3: include restriction class in outgoing call. \ 4: include both CUG ID and restriction \ class in outgoing call. \ 5: outgoing call is not allowed.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER noRestriction(1), closedUserGroupCall(2), restrictionClassCall(3), bothCUGandRCCall(4), inhibitAll(5)  

nvmVNETSwProfCfgInCallRestrict 1.3.6.1.4.1.335.1.4.21.1.8.1.3
NAME = ; DESC = The value of this object specifies how to \ handle incoming calls for voice channel \ switching. (Configuration); HELP = 2: check CUG ID in incoming call. (Must \ match our CUG ID for call acceptance. \ 3: check RCC in incoming call. (Must be \ greater than or equal to our RCC for call \ acceptance. \ 4: check both CUG and RCC in incoming \ call. \ 5: incoming call is not allowed.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER noRestriction(1), checkCUGID(2), checkRestrictionClassCode(3), cUGandPublicClassInhibit(4), inhibitAll(5)  

nvmVNETSwProfCfgCUGID 1.3.6.1.4.1.335.1.4.21.1.8.1.4
NAME = ; DESC = The value of this object assigns the Closed \ User Group ID for a voice channel. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..255  

nvmVNETSwProfCfgRestrictClassCd 1.3.6.1.4.1.335.1.4.21.1.8.1.5
NAME = ; DESC = The value of this object assigns the Restriction \ Class Code for a voice channel. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..255  

nvmVNETSwProfCfgAutoCallEntNum 1.3.6.1.4.1.335.1.4.21.1.8.1.6
NAME = ; DESC = The value of this object provides a voice \ channel Auto Call destination number by \ specifying an index into the ingress table. \ (Configuration); HELP = 0: auto call disabled. \ 1-32: index to the ingress table entry where \ the dial number is specified. \ The auto call for the ISDN BRI voice card is always \ disabled.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..32  

nvmVNETSwProfCfgCallNegStrategy 1.3.6.1.4.1.335.1.4.21.1.8.1.7
NAME = ; DESC = The value of this object specifies the preference \ for the voice algorithm when an outgoing call is \ made. (Configuration); HELP = specific: whatever is configured. \ bandwidth: bigger block size. \ delay: shorter block size.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER specific(1), bandwidth(2), delay(3)  

nvmVNETSwProfCfgTransmitPriority 1.3.6.1.4.1.335.1.4.21.1.8.1.8
NAME = ; DESC = The value of this object assigns the priority \ of the voice data to be transmitted. (Configuration); HELP = 0: lowest priority. \ 15: highest priority.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..15  

nvmVNETSwProfCfgAutoCallType 1.3.6.1.4.1.335.1.4.21.1.8.1.9
NAME = ; DESC = Indicates the type of auto-call \ switching to be performed by the \ voice channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER normal(1), masterHootnHoller(2), slaveHootnHoller(3)  

nvmVNETSwProfCfgAddServerSelect 1.3.6.1.4.1.335.1.4.21.1.8.1.10
NAME = ; DESC = Indicates which DNA server is used.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER nas(1), vncs(2)  

nvmVNETSwProfCfgOutCallMode 1.3.6.1.4.1.335.1.4.21.1.8.1.11
NAME = ; DESC = Indicates the type of call being made.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER enblock-only(1), dynamic(2)  

nvmVNETIngressDigFilterTable 1.3.6.1.4.1.335.1.4.21.1.9
NAME = ; DESC = The VNET Voice Ingress Digit Filtering \ Configuration table. (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
OBJECT-TYPE    
  SEQUENCE OF  
    NvmVNETIngressDigFilterEntry

nvmVNETIngressDigFilterEntry 1.3.6.1.4.1.335.1.4.21.1.9.1
NAME = ; DESC = An entry in the VNET Voice Ingress Digit \ Filtering Configuration table. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  NvmVNETIngressDigFilterEntry  

nvmVNETIngressDigFilterIndex 1.3.6.1.4.1.335.1.4.21.1.9.1.1
NAME = ; DESC = The value of this object indicates the index to \ the ingress table. Used as an index to the VNET \ Voice Ingress Digit Filtering Configuration table. \ Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..32  

nvmVNETIngressDigFilterIngressNum 1.3.6.1.4.1.335.1.4.21.1.9.1.2
NAME = ; DESC = The value of this object selects the digit \ pattern to be matched. (Null terminated \ character string.) (Configuration); HELP = Valid characters are decimal digits, '#', \ '*', '+', '[' and ']' .; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

nvmVNETIngressDigFilterManipString 1.3.6.1.4.1.335.1.4.21.1.9.1.3
NAME = ; DESC = The value of this object selects commands \ to produce the ingress digits for speed dial, \ call redirect, and source ID insertion features. \ (Configuration); HELP = Valid characters are decimal digits, '#', \ '*', 'D', and 'I'.; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

nvmVNETEgressDigManipTable 1.3.6.1.4.1.335.1.4.21.1.10
NAME = ; DESC = The VNET Voice Egress Digit Manipulation \ Configuration table. (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
OBJECT-TYPE    
  SEQUENCE OF  
    NvmVNETEgressDigManipEntry

nvmVNETEgressDigManipEntry 1.3.6.1.4.1.335.1.4.21.1.10.1
NAME = ; DESC = An entry in the VNET Voice Egress Digit \ Manipulation Configuration table. (Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  NvmVNETEgressDigManipEntry  

nvmVNETEgressDigManipIndex 1.3.6.1.4.1.335.1.4.21.1.10.1.1
NAME = ; DESC = The value of this object indicates the index to \ the egress table. Used as an index to the VNET \ Voice Egress Digit Manipulation Configuration \ table. Configuration); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..32  

nvmVNETEgressDigManipPhoneNum 1.3.6.1.4.1.335.1.4.21.1.10.1.2
NAME = ; DESC = The value of this object selects the phone \ number that voice channels are associated with. \ This is the number to be registered to the Address \ Server (RSA). (Configuration); HELP = Valid characters are decimal digits, '#', and '*'.; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

nvmVNETEgressDigManipString 1.3.6.1.4.1.335.1.4.21.1.10.1.3
NAME = ; DESC = The value of this object selects commands \ to produce the egress digits for FXO, E&M, \ or FXS 3-Port interface. The result is the \ number to be sent to the connected phone \ device. (Configuration); HELP = Valid characters are decimal digits, '#', '*', \ '+', 'D', 'H', and 'I'. The character 'H' is \ used to trigger immediate dial handling by the PBX.; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..40)  

nvmVNETEgressDigManipChIDList 1.3.6.1.4.1.335.1.4.21.1.10.1.4
NAME = ; DESC = The value of this object selects voice channels \ associated with the phone number. The valid \ string consists of the substring 'B1'~'B6', \ 'C1'~'C12', 'D1'~'D12', and 'E1'~'E2'. \ (Configuration); HELP = Valid characters are decimal digits, 'B', 'C', \ 'D', and 'E'.; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..70)  

vnet-control 1.3.6.1.4.1.335.1.4.21.2
OBJECT IDENTIFIER    

mcmVNETOutOfOrder 1.3.6.1.4.1.335.1.4.21.2
NAME = ; DESC = Indicates that the DSP is not running. \ A channel reset may be required.; HELP = DSP is not running. Reset voice channel(s). If problem still exist, \ contact sys admin. or Field Personnel.;
TRAP-TYPE    
  mcmSysAsciiTimeOfDay  
  mcmVNETChCfgLimID  
  mcmVNETChCfgChannelID  

mcmVNETChControlTable 1.3.6.1.4.1.335.1.4.21.2.1
NAME = ; DESC = The VNET Voice Channel Control table. \ HELP = ; CAPABILITIES = NET_OPER, VPN_OPER ;
OBJECT-TYPE    
  SEQUENCE OF  
    McmVNETChControlEntry

mcmVNETChControlEntry 1.3.6.1.4.1.335.1.4.21.2.1.1
NAME = ; DESC = An entry in the VNET Voice Channel Control \ table.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  McmVNETChControlEntry  

mcmVNETChControlLimID 1.3.6.1.4.1.335.1.4.21.2.1.1.1
NAME = ; DESC = The card lim (logical interface module) number of a \ particular voice channel. Used as an index to the \ VNET Voice Channel Control table.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER lim1(2), lim2(3), lim3(4), lim4(5), limB(6), limC(7), limD(8), limE(9)  

mcmVNETChControlChannelID 1.3.6.1.4.1.335.1.4.21.2.1.1.2
NAME = ; DESC = The position of the voice channel in the lim. \ Used as an index to the VNET Voice \ Channel Control table.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..12  

mcmVNETChControlActionCmd 1.3.6.1.4.1.335.1.4.21.2.1.1.3
NAME = ; DESC = Setting this object will perform various \ actions on the specified voice channel. \ Note: Starting with software release 3.0, \ the enumeration clearChannelCounters (2) is \ not supported. The enumeration is included \ here only to support backwards compatibility \ for software versions prior to release 3.0.; HELP = 1: perform hardware reset to DSP. \ 2: clear statistics counter. \ 3: download code to DSP. \ 4: disconnect call. \ 5: set DSP to loopback mode. \ 6: terminate test. \ 7: force connect channel by using the \ auto call number. NOTE: This option is not \ supported by the ISDN BRI voice card.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER resetChannel(1), clearChannelCounters(2), codeDownload(3), disconnect(4), loopbackTest(5), terminateTests(6), forceConnect(7)  

mcmVNETSysControlActionCmd 1.3.6.1.4.1.335.1.4.21.2.2
NAME = ; DESC = Setting this object will perform various \ actions on the VNET voice system. \ Note: Starting with software release 3.0, \ the enumerations clearNetworkCounters (1) and \ clearChannelCounters (3) are not supported. \ The enumeration is included here only to support \ backwards compatibility for software versions \ prior to release 3.0.; HELP = 1: clear network statistics counters. \ 2: perform hardware reset to all channels. \ 3: clear all channel statistics counters. \ 4: download code to all channels. \ 5: disconnect all channel's calls. \ 6: set all channels to loopback mode. \ 7: terminate all channel's tests. \ 8: force connect all channels by using the auto call numbers. NOTE: This option is not \ supported by the ISDN BRI voice card.; \ 9: re-register phone number.; CAPABILITIES = NET_OPER, VPN_OPER ;
OBJECT-TYPE    
  INTEGER clearNetworkCounters(1), resetChannels(2), clearChannelCounters(3), download(4), disconnect(5), loopbackTests(6), terminateTests(7), forceConnects(8), reRegisterPhoneNum(9)  

vnet-status 1.3.6.1.4.1.335.1.4.21.3
OBJECT IDENTIFIER    

mcmVNETOutOfOrderRecovered 1.3.6.1.4.1.335.1.4.21.3
NAME = ; DESC = Indicates recovery from the out of order condition.\ Severity Level: CRITICAL.; HELP = DSP is running. Normal status indication.;
TRAP-TYPE    
  mcmSysAsciiTimeOfDay  
  mcmVNETChCfgLimID  
  mcmVNETChCfgChannelID  

mcmVNETChStatusTable 1.3.6.1.4.1.335.1.4.21.3.1
NAME = ; DESC = The VNET Voice Channel Status Display table. \ HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
OBJECT-TYPE    
  SEQUENCE OF  
    McmVNETChStatusEntry

mcmVNETChStatusEntry 1.3.6.1.4.1.335.1.4.21.3.1.1
NAME = ; DESC = An entry in the VNET Voice Channel Status Display \ table.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  McmVNETChStatusEntry  

mcmVNETChStatusLimID 1.3.6.1.4.1.335.1.4.21.3.1.1.1
NAME = ; DESC = The card lim (logical interface module) number of \ a particular voice channel. Used as an index to \ the VNET Voice Channel Status Display table.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER lim1(2), lim2(3), lim3(4), lim4(5), limB(6), limC(7), limD(8), limE(9)  

mcmVNETChStatusChannelID 1.3.6.1.4.1.335.1.4.21.3.1.1.2
NAME = ; DESC = The position of the voice channel in the lim. \ Used as an index to the VNET Voice \ Channel Status Display table.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..12  

mcmVNETChStatusInterfaceType 1.3.6.1.4.1.335.1.4.21.3.1.1.3
NAME = ; DESC = The value of this object indicates the interface \ type of the specified voice channel.; HELP = Upon powerup, the interface type will not be \ available until the DSP software is loaded and its \ status is reported.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER not-available(1), enhanced-loop-start-FXS(2), enhanced-EandM(3), enhanced-loop-start-FXO(4), low-cost-loop-start-FXS(5), low-cost-EandM(6), low-cost-loop-start-FXO(7), ground-start-FXS(8), ground-start-FXO(9), three-port(10), dvm(11), bri(12)  

mcmVNETChStatusInterfaceSwID 1.3.6.1.4.1.335.1.4.21.3.1.1.4
NAME = ; DESC = The value of this object indicates the command \ interface version ID (CIVID) of the specified voice \ channel. (Note: CIVID is 20 or above.); HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..255  

mcmVNETChStatusEMType 1.3.6.1.4.1.335.1.4.21.3.1.1.5
NAME = ; DESC = The value of this object indicates the E&M \ type of the specified voice channel.; HELP = This is for E&M interface channels only. Other \ interface types will show notApplicable.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER typeI(1), typeII(2), typeIII(3), typeIV(4), typeV(5), notApplicable(6)  

mcmVNETChStatusModelID 1.3.6.1.4.1.335.1.4.21.3.1.1.6
NAME = ; DESC = The value of this object indicates the hardware \ module type for the specified DVM voice channel.; HELP = This is for DVM voice channels only. Analog \ voice channels will show notApplicable.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER t1(1), e1(2), notApplicable(3)  

mcmVNETChStatusDSPOperation 1.3.6.1.4.1.335.1.4.21.3.1.1.7
NAME = ; DESC = The value of this object indicates the current \ DSP status of the specified voice channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER dead(1), notReady(2), downloadFailure(3), forceConnected(4), forceConnected-TimedOut(5), idle(6), switchConnectInProgress(7), switchConnected(8), switchDisconnectInProgress(9), busyOut(10), codeDownloadInProgress(11), pcmChannelNotInstalled(12)  

mcmVNETChStatusNetworkConnect 1.3.6.1.4.1.335.1.4.21.3.1.1.8
NAME = ; DESC = The value of this object indicates the current \ channel network connect status of the specified \ voice channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER idle(1), callInProgress(2), locallyConnected(3), remotelyConnected(4), disconnectInProgress(5)  

mcmVNETChStatusRemoteChHwType 1.3.6.1.4.1.335.1.4.21.3.1.1.9
NAME = ; DESC = The value of this object indicates the remote \ voice channel hardware type (corresponding to \ the specified voice channel).; HELP = This will be the NULL string if the specified \ voice channel is not connected.; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..15)  

mcmVNETChStatusRemoteChNodeName 1.3.6.1.4.1.335.1.4.21.3.1.1.10
NAME = ; DESC = The value of this object indicates the remote \ voice channel node name (corresponding to \ the specified voice channel).; HELP = This will be the NULL string if the specified \ voice channel is not connected.; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

mcmVNETChStatusRemoteChNum 1.3.6.1.4.1.335.1.4.21.3.1.1.11
NAME = ; DESC = The value of this object indicates the remote \ voice channel number (corresponding to \ the specified voice channel).; HELP = This will be the NULL string if the specified \ voice channel is not connected.; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..7)  

mcmVNETChStatusRemoteChIfType 1.3.6.1.4.1.335.1.4.21.3.1.1.12
NAME = ; DESC = The value of this object indicates the remote \ voice channel interface type (corresponding to \ the specified voice channel).; HELP = This will be the NULL string if the specified \ voice channel is not connected.; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..31)  

mcmVNETChStatusRemoteFrameIfVer 1.3.6.1.4.1.335.1.4.21.3.1.1.13
NAME = ; DESC = The value of this object indicates the final \ negotiated software version to be run on both \ sides of a voice channel connection.; HELP = This will be 0 if the specified \ voice channel is not connected.; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 0..255  

mcmVNETChStatusRemoteChVoiceAlg 1.3.6.1.4.1.335.1.4.21.3.1.1.14
NAME = ; DESC = The value of this object indicates the final \ negotiated voice algorithm running on both \ sides of a voice channel connection.; HELP = This will be the NULL string if the specified \ voice channel is not connected.; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..23)  

mcmVNETChStatusRemoteChFaxAlg 1.3.6.1.4.1.335.1.4.21.3.1.1.15
NAME = ; DESC = The value of this object indicates the final \ negotiated voice fax algorithm and maximum \ speed running on both sides of a voice fax \ channel connection.; HELP = This will be the NULL string if the specified \ voice fax channel is not connected.; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..15)  

mcmVNETChStatusRemoteChModemAlg 1.3.6.1.4.1.335.1.4.21.3.1.1.16
NAME = ; DESC = The value of this object indicates the final \ negotiated voice modem algorithm and maximum \ speed running on both sides of a voice modem \ channel connection.; HELP = This will be the NULL string if the specified \ voice fax channel is not connected.; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..15)  

mcmVNETChStatusSelfTestResult 1.3.6.1.4.1.335.1.4.21.3.1.1.17
NAME = ; DESC = The value of this object indicates the results \ of a self test performed on the specified voice \ channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER testPassed(1), testFailed(2)  

mcmVNETChStatusFlashEPROM 1.3.6.1.4.1.335.1.4.21.3.1.1.18
NAME = ; DESC = The value of this object indicates the current \ flash EPROM status in the DSP of the specified \ voice channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER notInstalled(1), valid(2), erased(3), invalidChecksum(4), noAnalogInterfaceDriver(5), securityViolation(6)  

mcmVNETChStatusEPROM 1.3.6.1.4.1.335.1.4.21.3.1.1.19
NAME = ; DESC = The value of this object indicates the current \ EPROM status in the DSP of the specified voice \ channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER notInstalled(1), currentlyOperating(2), presentButNotOperating(3)  

mcmVNETChStatusDspPROMVer 1.3.6.1.4.1.335.1.4.21.3.1.1.20
NAME = ; DESC = The value of this object indicates the DSP PROM \ version of the specified voice channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..7)  

mcmVNETChStatusPROMID 1.3.6.1.4.1.335.1.4.21.3.1.1.21
NAME = ; DESC = The value of this object indicates the PROM \ ID of the specified voice channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  DisplayString SIZE(0..15)  

mcmVNETChStatusInputLevel 1.3.6.1.4.1.335.1.4.21.3.1.1.22
NAME = ; DESC = The value of this object indicates the input \ level of the specified voice channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER lessThanNeg25dBm(1), neg24dBm(2), neg21dBm(3), neg18dBm(4), neg15dBm(5), neg12dBm(6), neg10dBm(7), neg8dBm(8), neg6dBm(9), neg5dBm(10), neg4dBm(11), neg3dBm(12), neg2dBm(13), neg1dBm(14), zerodBm(15), greaterThan0dBm(16), notApplicable(17)  

voiceSysStatusGroup 1.3.6.1.4.1.335.1.4.21.3.2
OBJECT IDENTIFIER    

voiceSysStatusPhoneRegistrationStatus 1.3.6.1.4.1.335.1.4.21.3.2.1
NAME = PhoneRegistrationStatus; DESC = Indicates current communications \ status with NAS; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
OBJECT-TYPE    
  INTEGER registrationComplete(1), registrationInProgress(2), nasAddressNotConfigured(3), lostCommunicationWithNAS(4), noResponseFromNAS(5), registrationFailed(6)  

vnet-statistics 1.3.6.1.4.1.335.1.4.21.4
OBJECT IDENTIFIER    

mcmVNETFailedToSyncUp 1.3.6.1.4.1.335.1.4.21.4
NAME = ; DESC = Indicates that the DSP is running, \ but unable to sync up. A channel reset \ may be required.\ Severity Level: MAJOR.; HELP = Reset channel(s). If Synchronization is not acquired, \ contact sys admin., or Field Personnel.;
TRAP-TYPE    
  mcmSysAsciiTimeOfDay  
  mcmVNETChCfgLimID  
  mcmVNETChCfgChannelID  

mcmVNETChStatsTable 1.3.6.1.4.1.335.1.4.21.4.1
NAME = ; DESC = The VNET Voice Channel Statistics Display table. \ HELP = ; CAPABILITIES = NET_CFG, VPN_CFG;
OBJECT-TYPE    
  SEQUENCE OF  
    McmVNETChStatsEntry

mcmVNETChStatsEntry 1.3.6.1.4.1.335.1.4.21.4.1.1
NAME = ; DESC = An entry in the VNET Voice Channel Statistics \ Display table.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  McmVNETChStatsEntry  

mcmVNETChStatsLimID 1.3.6.1.4.1.335.1.4.21.4.1.1.1
NAME = ; DESC = The card lim (logical interface module) number of a \ particular voice channel. Used as an index to the \ VNET Voice Channel Statistics Display table.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER lim1(2), lim2(3), lim3(4), lim4(5), limB(6), limC(7), limD(8), limE(9)  

mcmVNETChStatsChannelID 1.3.6.1.4.1.335.1.4.21.4.1.1.2
NAME = ; DESC = The position of the voice channel in the lim. \ Used as an index to the VNET Voice \ Channel Statistics Display table.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  INTEGER 1..12  

mcmVNETChStatsOutCallConnTime 1.3.6.1.4.1.335.1.4.21.4.1.1.3
NAME = ; DESC = The value of this object indicates the total \ connection time (in sec) since the last statistics \ reset for the specified voice channel outgoing \ calls. (Excludes call setup time and local calls.) ; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  Counter  

mcmVNETChStatsInCallConnTime 1.3.6.1.4.1.335.1.4.21.4.1.1.4
NAME = ; DESC = The value of this object indicates the total \ connection time (in sec) since the last statistics \ reset for the specified voice channel incoming \ calls. (Excludes local calls.) ; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  Counter  

mcmVNETChStatsOutCallsSucceded 1.3.6.1.4.1.335.1.4.21.4.1.1.5
NAME = ; DESC = The value of this object indicates the total \ number of positive call responses sent from the \ remote DSP since the last statistics reset \ for the specified voice channel. (Excludes \ local calls.) ; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  Counter  

mcmVNETChStatsOutCallsFailed 1.3.6.1.4.1.335.1.4.21.4.1.1.6
NAME = ; DESC = The value of this object indicates the total \ number of negative call responses sent from the \ remote DSP since the last statistics reset \ for the specified voice channel. (Excludes \ local calls.) ; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  Counter  

mcmVNETChStatsInCallsAccepted 1.3.6.1.4.1.335.1.4.21.4.1.1.7
NAME = ; DESC = The value of this object indicates the total \ number of positive call responses sent to the \ remote DSP since the last statistics reset \ for the specified voice channel. (Excludes \ local calls.) ; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  Counter  

mcmVNETChStatsInCallsRejected 1.3.6.1.4.1.335.1.4.21.4.1.1.8
NAME = ; DESC = The value of this object indicates the total \ number of negative call responses sent to the \ remote DSP since the last statistics reset \ for the specified voice channel. (Excludes \ local calls.) ; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  Counter  

mcmVNETChStatsNumberOfResets 1.3.6.1.4.1.335.1.4.21.4.1.1.9
NAME = ; DESC = The value of this object indicates the total \ number of resets sent to the DSP corresponding \ to the specified voice channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  Counter  

mcmVNETChStatsNumberOfRetries 1.3.6.1.4.1.335.1.4.21.4.1.1.10
NAME = ; DESC = The value of this object indicates the total \ number of no responses sent from the DSP \ since the last DSP reset corresponding \ to the specified voice channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  Counter  

mcmVNETChStatsBBCFramesRcvd 1.3.6.1.4.1.335.1.4.21.4.1.1.11
NAME = ; DESC = The value of this object indicates the total \ number of frames with Bad Byte Count received \ from the DSP corresponding to the specified \ voice channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  Counter  

mcmVNETChStatsBEOFFramesRcvd 1.3.6.1.4.1.335.1.4.21.4.1.1.12
NAME = ; DESC = The value of this object indicates the total \ number of frames with Bad End Of Frame \ character received from the DSP corresponding \ to the specified voice channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  Counter  

mcmVNETChStatsLostSpeechFrames 1.3.6.1.4.1.335.1.4.21.4.1.1.13
NAME = ; DESC = The value of this object indicates the total \ number of speech frames sent by the remote \ that were lost since power up corresponding \ to the specified voice channel.; HELP = Always 0 if sequence number in speech frame \ is not used.; CAPABILITIES = ;
OBJECT-TYPE    
  Counter  

mcmVNETChStatsLostControlFrames 1.3.6.1.4.1.335.1.4.21.4.1.1.14
NAME = ; DESC = The value of this object indicates the total \ number of control frames sent by the remote \ that were lost corresponding to the specified \ voice channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  Counter  

mcmVNETChStatsInvalPayloadFrRcvd 1.3.6.1.4.1.335.1.4.21.4.1.1.15
NAME = ; DESC = The value of this object indicates the total \ number of payload frames received from the \ remote with bad length or frame type \ corresponding to the specified voice channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  Counter  

mcmVNETChStatsInvalPUMPMsgRcvd 1.3.6.1.4.1.335.1.4.21.4.1.1.16
NAME = ; DESC = The value of this object indicates the total \ number of PUMP messages received from the \ remote with unknown message type, IEs, or \ invalid length corresponding to the specified \ voice channel.; HELP = ; CAPABILITIES = ;
OBJECT-TYPE    
  Counter  

mcmVNETNetStatsGroup 1.3.6.1.4.1.335.1.4.21.4.2
OBJECT IDENTIFIER    

mcmVNETNetStatsSucceedOutSVCCalls 1.3.6.1.4.1.335.1.4.21.4.2.1
NAME = ; DESC = The value of this object indicates the total \ number of successful SVC calls since the \ last network statistics reset.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;
OBJECT-TYPE    
  Counter  

mcmVNETNetStatsFailedOutSVCCalls 1.3.6.1.4.1.335.1.4.21.4.2.2
NAME = ; DESC = The value of this object indicates the total \ number of unsuccessful SVC calls since the \ last network statistics reset.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;
OBJECT-TYPE    
  Counter  

mcmVNETNetStatsAcceptedInCalls 1.3.6.1.4.1.335.1.4.21.4.2.3
NAME = ; DESC = The value of this object indicates the total \ number of SVC calls accepted by this access device \ since the last network statistics reset.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;
OBJECT-TYPE    
  Counter  

mcmVNETNetStatsRejectedInCalls 1.3.6.1.4.1.335.1.4.21.4.2.4
NAME = ; DESC = The value of this object indicates the total \ number of SVC calls rejected by this access device \ since the last network statistics reset.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;
OBJECT-TYPE    
  Counter  

mcmVNETNetStatsSucceedDNARequests 1.3.6.1.4.1.335.1.4.21.4.2.5
NAME = ; DESC = The value of this object indicates the total \ number of successful DNA requests received \ by this access device since the last network \ statistics reset.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;
OBJECT-TYPE    
  Counter  

mcmVNETNetStatsFailedDNARequests 1.3.6.1.4.1.335.1.4.21.4.2.6
NAME = ; DESC = The value of this object indicates the total \ number of unsuccessful DNA requests received \ by this access device since the last network \ statistics reset.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;
OBJECT-TYPE    
  Counter  

mcmVNETNetStatsFailedBuffAllocations 1.3.6.1.4.1.335.1.4.21.4.2.7
NAME = ; DESC = The value of this object indicates the total \ number of streams buffers not available \ to this access device.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;
OBJECT-TYPE    
  Counter  

mcmVNETNetStatsNumActiveCalls 1.3.6.1.4.1.335.1.4.21.4.2.8
NAME = ; DESC = The value of this object indicates the total \ number of calls in progress or connected \ in this access device.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ;
OBJECT-TYPE    
  Counter  

mcmVNETFailedToSyncUpRecovered 1.3.6.1.4.1.335.1.4.21.5
NAME = ; DESC = Indicates recovery from the failure to \ sync up condition.\ Severity Level: INFORMATIVE. ; HELP = Synchronization is acquired. Normal Status Indicator.;
TRAP-TYPE    
  mcmSysAsciiTimeOfDay  
  mcmVNETChCfgLimID  
  mcmVNETChCfgChannelID  

mcmVNETNoCVMCodeImage 1.3.6.1.4.1.335.1.4.21.6
NAME = ; DESC = Indicates that the built image doesn't \ contain CVM code\ Severity Level: MAJOR.; HELP = Access device code does not contain image for CVM module. \ Please contact Sys Admin., or Field Personnel. ;
TRAP-TYPE    
  mcmSysAsciiTimeOfDay  

mcmVNETNoTUVMCodeImage 1.3.6.1.4.1.335.1.4.21.7
NAME = ; DESC = Indicates that the built image doesn't \ contain TUVM code.\ Severity Level: MAJOR.; HELP = Access device code does not contain image for TUVM module. \ Please contact Sys Admin., or Field Personnel. ;
TRAP-TYPE    
  mcmSysAsciiTimeOfDay  

mcmVNETNoDVMCodeImage 1.3.6.1.4.1.335.1.4.21.8
NAME = ; DESC = Indicates that the built image doesn't \ contain DVM code.\ Severity Level: MAJOR.; HELP = Access device code does not contain image for DVM module. \ Please contact Sys Admin., or Field Personnel. ;
TRAP-TYPE    
  mcmSysAsciiTimeOfDay  

Defined Objects

McmVNETChCfgEntry  
SEQUENCE    
  INTEGER as mcmVNETChCfgLimID  
  INTEGER as mcmVNETChCfgChannelID  
  INTEGER as mcmVNETChCfgVoiceProfile  
  INTEGER as mcmVNETChCfgSwitchingProfile  
  INTEGER as mcmVNETChCfgInterfaceType  

McmVNETProfileCfgEntry  
SEQUENCE    
  INTEGER as mcmVNETProfileCfgProfileNum  
  INTEGER as mcmVNETProfileCfgMode  
  INTEGER as mcmVNETProfileCfgDigitizingRate  
  INTEGER as mcmVNETProfileCfgInputLevelGain  
  INTEGER as mcmVNETProfileCfgOutputLevelAttn  
  INTEGER as mcmVNETProfileCfgBusyOutMode  
  INTEGER as mcmVNETProfileCfgBandwidth  
  INTEGER as mcmVNETProfileCfgBackground  
  INTEGER as mcmVNETProfileCfgBRIPulseRate  
  INTEGER as mcmVNETProfileCfgEMSigFormat  
  INTEGER as mcmVNETProfileCfgFXSSigFormat  
  INTEGER as mcmVNETProfileCfgDVMSigFormat  
  INTEGER as mcmVNETProfileCfgNumberOfRings  
  INTEGER as mcmVNETProfileCfgEMAnalOper  
  INTEGER as mcmVNETProfileCfgRingingFreq  
  INTEGER as mcmVNETProfileCfgFaxDigRate  
  INTEGER as mcmVNETProfileCfgDiscSupervision  
  INTEGER as mcmVNETProfileCfgLineImpedance  
  INTEGER as mcmVNETProfileCfgMaxOutputLevel  
  INTEGER as mcmVNETProfileCfgRegenDelay  
  INTEGER as mcmVNETProfileCfgDialDigTimeLimit  
  INTEGER as mcmVNETProfileCfgMaxNumForDig  
  INTEGER as mcmVNETProfileCfgRegenFormat  
  INTEGER as mcmVNETProfileCfgCallProgTone  
  INTEGER as mcmVNETProfileCfgDTMFDetector  
  INTEGER as mcmVNETProfileCfgJitters  
  INTEGER as mcmVNETProfileCfgEchoCanceller  
  INTEGER as mcmVNETProfileCfgAutoGainControl  
  INTEGER as mcmVNETProfileCfgCompanderFormat  
  INTEGER as mcmVNETProfileCfgPremiumVoice  
  INTEGER as mcmVNETProfileCfgEndOfDialChar  
  INTEGER as mcmVNETProfileCfgBckGrndNoiseLevel  
  INTEGER as mcmVNETProfileCfgSilenceHngOvrTime  
  INTEGER as mcmVNETProfileCfgIdlePattern  
  INTEGER as mcmVNETProfileCfgEcanFilterLength  
  INTEGER as mcmVNETProfileCfgEcanErlImprovement  
  INTEGER as mcmVNETProfileCfgNoiseFloorOffset  
  INTEGER as mcmVNETProfileCfgDtmfGenBurstLength  
  INTEGER as mcmVNETProfileCfgDtmRegenBurstLength  

McmVNETSwProfCfgEntry  
SEQUENCE    
  INTEGER as mcmVNETSwProfCfgProfileNum  
  INTEGER as mcmVNETSwProfCfgOutCallRestrict  
  INTEGER as mcmVNETSwProfCfgInCallRestrict  
  INTEGER as mcmVNETSwProfCfgCUGID  
  INTEGER as mcmVNETSwProfCfgRestrictClassCd  
  INTEGER as mcmVNETSwProfCfgAutoCallEntNum  
  INTEGER as mcmVNETSwProfCfgCallNegStrategy  
  INTEGER as mcmVNETSwProfCfgTransmitPriority  
  INTEGER as mcmVNETSwProfCfgAutoCallType  
  INTEGER as mcmVNETSwProfCfgAddServerSelect  
  INTEGER as mcmVNETSwProfCfgOutCallMode  

McmVNETIngressDigFilterEntry  
SEQUENCE    
  INTEGER as mcmVNETIngressDigFilterIndex  
  DisplayString as mcmVNETIngressDigFilterIngressNum  
  DisplayString as mcmVNETIngressDigFilterManipString  

McmVNETEgressDigManipEntry  
SEQUENCE    
  INTEGER as mcmVNETEgressDigManipIndex  
  DisplayString as mcmVNETEgressDigManipPhoneNum  
  DisplayString as mcmVNETEgressDigManipString  
  DisplayString as mcmVNETEgressDigManipChIDList  

NvmVNETChCfgEntry  
SEQUENCE    
  INTEGER as nvmVNETChCfgLimID  
  INTEGER as nvmVNETChCfgChannelID  
  INTEGER as nvmVNETChCfgVoiceProfile  
  INTEGER as nvmVNETChCfgSwitchingProfile  
  INTEGER as nvmVNETChCfgInterfaceType  

NvmVNETProfileCfgEntry  
SEQUENCE    
  INTEGER as nvmVNETProfileCfgProfileNum  
  INTEGER as nvmVNETProfileCfgMode  
  INTEGER as nvmVNETProfileCfgDigitizingRate  
  INTEGER as nvmVNETProfileCfgInputLevelGain  
  INTEGER as nvmVNETProfileCfgOutputLevelAttn  
  INTEGER as nvmVNETProfileCfgBusyOutMode  
  INTEGER as nvmVNETProfileCfgBandwidth  
  INTEGER as nvmVNETProfileCfgBackground  
  INTEGER as nvmVNETProfileCfgBRIPulseRate  
  INTEGER as nvmVNETProfileCfgEMSigFormat  
  INTEGER as nvmVNETProfileCfgFXSSigFormat  
  INTEGER as nvmVNETProfileCfgDVMSigFormat  
  INTEGER as nvmVNETProfileCfgNumberOfRings  
  INTEGER as nvmVNETProfileCfgEMAnalOper  
  INTEGER as nvmVNETProfileCfgRingingFreq  
  INTEGER as nvmVNETProfileCfgFaxDigRate  
  INTEGER as nvmVNETProfileCfgDiscSupervision  
  INTEGER as nvmVNETProfileCfgLineImpedance  
  INTEGER as nvmVNETProfileCfgMaxOutputLevel  
  INTEGER as nvmVNETProfileCfgRegenDelay  
  INTEGER as nvmVNETProfileCfgDialDigTimeLimit  
  INTEGER as nvmVNETProfileCfgMaxNumForDig  
  INTEGER as nvmVNETProfileCfgRegenFormat  
  INTEGER as nvmVNETProfileCfgCallProgTone  
  INTEGER as nvmVNETProfileCfgDTMFDetector  
  INTEGER as nvmVNETProfileCfgJitters  
  INTEGER as nvmVNETProfileCfgEchoCanceller  
  INTEGER as nvmVNETProfileCfgAutoGainControl  
  INTEGER as nvmVNETProfileCfgCompanderFormat  
  INTEGER as nvmVNETProfileCfgPremiumVoice  
  INTEGER as nvmVNETProfileCfgEndOfDialChar  
  INTEGER as nvmVNETProfileCfgBckGrndNoiseLevel  
  INTEGER as nvmVNETProfileCfgSilenceHngOvrTime  
  INTEGER as nvmVNETProfileCfgIdlePattern  
  INTEGER as nvmVNETProfileCfgEcanFilterLength  
  INTEGER as nvmVNETProfileCfgEcanErlImprovement  
  INTEGER as nvmVNETProfileCfgNoiseFloorOffset  
  INTEGER as nvmVNETProfileCfgDtmfGenBurstLength  
  INTEGER as nvmVNETProfileCfgDtmRegenBurstLength  

NvmVNETSwProfCfgEntry  
SEQUENCE    
  INTEGER as nvmVNETSwProfCfgProfileNum  
  INTEGER as nvmVNETSwProfCfgOutCallRestrict  
  INTEGER as nvmVNETSwProfCfgInCallRestrict  
  INTEGER as nvmVNETSwProfCfgCUGID  
  INTEGER as nvmVNETSwProfCfgRestrictClassCd  
  INTEGER as nvmVNETSwProfCfgAutoCallEntNum  
  INTEGER as nvmVNETSwProfCfgCallNegStrategy  
  INTEGER as nvmVNETSwProfCfgTransmitPriority  
  INTEGER as nvmVNETSwProfCfgAutoCallType  
  INTEGER as nvmVNETSwProfCfgAddServerSelect  
  INTEGER as nvmVNETSwProfCfgOutCallMode  

NvmVNETIngressDigFilterEntry  
SEQUENCE    
  INTEGER as nvmVNETIngressDigFilterIndex  
  DisplayString as nvmVNETIngressDigFilterIngressNum  
  DisplayString as nvmVNETIngressDigFilterManipString  

NvmVNETEgressDigManipEntry  
SEQUENCE    
  INTEGER as nvmVNETEgressDigManipIndex  
  DisplayString as nvmVNETEgressDigManipPhoneNum  
  DisplayString as nvmVNETEgressDigManipString  
  DisplayString as nvmVNETEgressDigManipChIDList  

McmVNETChStatusEntry  
SEQUENCE    
  INTEGER as mcmVNETChStatusLimID  
  INTEGER as mcmVNETChStatusChannelID  
  INTEGER as mcmVNETChStatusInterfaceType  
  INTEGER as mcmVNETChStatusInterfaceSwID  
  INTEGER as mcmVNETChStatusEMType  
  INTEGER as mcmVNETChStatusModelID  
  INTEGER as mcmVNETChStatusDSPOperation  
  INTEGER as mcmVNETChStatusNetworkConnect  
  DisplayString as mcmVNETChStatusRemoteChHwType  
  DisplayString as mcmVNETChStatusRemoteChNodeName  
  DisplayString as mcmVNETChStatusRemoteChNum  
  DisplayString as mcmVNETChStatusRemoteChIfType  
  INTEGER as mcmVNETChStatusRemoteFrameIfVer  
  DisplayString as mcmVNETChStatusRemoteChVoiceAlg  
  DisplayString as mcmVNETChStatusRemoteChFaxAlg  
  DisplayString as mcmVNETChStatusRemoteChModemAlg  
  INTEGER as mcmVNETChStatusSelfTestResult  
  INTEGER as mcmVNETChStatusFlashEPROM  
  INTEGER as mcmVNETChStatusEPROM  
  DisplayString as mcmVNETChStatusDspPROMVer  
  DisplayString as mcmVNETChStatusPROMID  
  INTEGER as mcmVNETChStatusInputLevel  

McmVNETChStatsEntry  
SEQUENCE    
  INTEGER as mcmVNETChStatsLimID  
  INTEGER as mcmVNETChStatsChannelID  
  Counter as mcmVNETChStatsOutCallConnTime  
  Counter as mcmVNETChStatsInCallConnTime  
  Counter as mcmVNETChStatsOutCallsSucceded  
  Counter as mcmVNETChStatsOutCallsFailed  
  Counter as mcmVNETChStatsInCallsAccepted  
  Counter as mcmVNETChStatsInCallsRejected  
  Counter as mcmVNETChStatsNumberOfResets  
  Counter as mcmVNETChStatsNumberOfRetries  
  Counter as mcmVNETChStatsBBCFramesRcvd  
  Counter as mcmVNETChStatsBEOFFramesRcvd  
  Counter as mcmVNETChStatsLostSpeechFrames  
  Counter as mcmVNETChStatsLostControlFrames  
  Counter as mcmVNETChStatsInvalPayloadFrRcvd  
  Counter as mcmVNETChStatsInvalPUMPMsgRcvd  

McmVNETChControlEntry  
SEQUENCE    
  INTEGER as mcmVNETChControlLimID  
  INTEGER as mcmVNETChControlChannelID  
  INTEGER as mcmVNETChControlActionCmd