
MPLS-TC-MIB
File:
MPLS-TC-MIB.mib (9337 bytes)
Imported modules
Imported symbols
Defined Objects
| mplsMIB |
1.3.6.1.2.1.10.9999 |
| OBJECT IDENTIFIER |
|
|
|
| mplsTCMIB |
1.3.6.1.2.1.10.9999.1 |
| This MIB module defines Textual Conventions and OBJECT-IDENTITIES for use in documents defining management information bases (MIBs) for managing MPLS networks. |
| MODULE-IDENTITY |
|
|
|
Defined Objects
| MplsAtmVcIdentifier |
|
| The VCI value for a VCL. The maximum VCI value cannot exceed the value allowable by atmInterfaceMaxVciBits defined in ATM-MIB. The minimum value is 32, values 0 to 31 are reserved for other uses by the ITU and ATM Forum. 32 is typically the default value for the Control VC. |
| TEXTUAL-CONVENTION |
|
|
|
| |
Integer32 |
32..65535 |
|
| MplsBitRate |
|
| An estimate of bandwidth in units of 1,000 bits per second. If this object reports a value of 'n' then the rate of the object is somewhere in the range of 'n-500' to 'n+499'. For objects which do not vary in bit rate, or for those where no accurate estimation can be made, this object should contain the nominal bit rate. |
| TEXTUAL-CONVENTION |
|
|
|
| |
Integer32 |
1..2147483647 |
|
| MplsExtendedTunnelId |
|
| A unique identifier for an MPLS Tunnel. This MAY represent an IpV4 address of the ingress or egress LSR for the tunnel. This value is derived from the Extended Tunnel Id in RSVP or the Ingress Router ID for CR-LDP. |
| TEXTUAL-CONVENTION |
|
|
|
| |
Unsigned32 |
|
|
| MplsInitialCreationSource |
|
| The entity that originally created the object in question. The values of this enumeration are defined as follows: other(1) - This is used when an entity which has not been enumerated in this textual convention but which is known by the agent. snmp(2) - The Simple Network Management Protocol was used to configure this object initially. ldp(3 - The Label Distribution Protocol was used to configure this object initially. rsvp(4) - The Resource Reservation Protocol was used to configure this object initially. crldp(5) - The Constraint-Based Label Distribution Protocol was used to configure this object initially. policyAgent(6) - A policy agent (perhaps in combination with one of the above protocols) was used to configure this object initially. unknown(7) - the agent cannot discern which component created the object. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
other(1), snmp(2), ldp(3), rsvp(4), crldp(5), policyAgent(6), unknown(7) |
|
| MplsLSPID |
|
| An identifier that is assigned to each LSP and is used to uniquely identify it. This is assigned at the head end of the LSP and can be used by all LSRs to identify this LSP. This value is piggybacked by the signaling protocol when this LSP is signaled within the network. This identifier can then be used at each LSR to identify which labels are being swapped to other labels for this LSP. For IPv4 addresses this results in a 6-octet long cookie. |
| TEXTUAL-CONVENTION |
|
|
|
| |
OCTET STRING |
SIZE(0..31) |
|
| MplsLdpIdentifier |
|
| The LDP identifier is a six octet quantity which is used to identify an Label Switch Router (LSR) label space. The first four octets identify the LSR and must be a globally unique value, such as a 32-bit router ID assigned to the LSR, and the last two octets identify a specific label space within the LSR. |
| TEXTUAL-CONVENTION |
|
|
|
| |
OCTET STRING |
SIZE(6) |
|
| MplsLdpLabelTypes |
|
| The Layer 2 label types which are defined for MPLS LDP/CRLDP are generic(1), atm(2), or frameRelay(3). |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
generic(1), atm(2), frameRelay(3) |
|