
| RFC-1212 | PROTEON-MIB | RFC1155-SMI |
| RFC-1215 |
| OBJECT-TYPE | proElsSubSysEventMsg | enterprises |
| TRAP-TYPE |
| ibm | 1.3.6.1.4.1.2 | ||
| OBJECT IDENTIFIER | |||
| ibmProd | 1.3.6.1.4.1.2.6 | ||
| OBJECT IDENTIFIER | |||
| nwaysMSS | 1.3.6.1.4.1.2.6.118 | ||
| OBJECT IDENTIFIER | |||
| mssServer8210 | 1.3.6.1.4.1.2.6.118.2 | ||
| OBJECT IDENTIFIER | |||
| mss8210Prod | 1.3.6.1.4.1.2.6.118.2.1 | ||
| OBJECT IDENTIFIER | |||
| mss8210ResetFlag | 1.3.6.1.4.1.2.6.118.2.1.1 | ||
| The flag that controls the reset process in this stand-alone. This variable shall assume a value of noreset(1) in the absence of a request for a reset from the management application. This variable shall assume a value of reboot(2) if the management application requests that this stand-alone execute a complete hardware reboot which reloads the code load from storage. | |||
| OBJECT-TYPE | |||
| INTEGER | noreset(1), reboot(2) | ||
| mss8210DRAMinstalled | 1.3.6.1.4.1.2.6.118.2.1.2 | ||
| The total amount of dynamic RAM installed on this stand-alone. The amount is in units of megabytes. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| mss8210NotifyStatus | 1.3.6.1.4.1.2.6.118.2.1.3 | ||
| The status of the trap reporting service in this stand-alone. This variable shall assume a value of enabled(1) if this stand-alone is permitted to send traps. This variable shall assume a value of disabled(2) if this stand-alone is prohibited from sending traps. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| mss8210TempThresholdStatus | 1.3.6.1.4.1.2.6.118.2.1.4 | ||
| The status of the temperature in this stand-alone. This variable shall assume a value of normal(1) if the temperature is within proper operating range for this stand-alone. This variable shall assume a value of warning(2) if the temperature becomes elevated but this stand-alone can still operate. This variable shall assume a value of shutdown(3) if the temperature is beyond the operating limits of this stand-alone. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), warning(2), shutdown(3) | ||
| mss8210PCAdapter | 1.3.6.1.4.1.2.6.118.2.2 | ||
| OBJECT IDENTIFIER | |||
| mssServer8210ELSTrapV2 | 1.3.6.1.4.1.2.6.118.2.2 | ||
| The trap announces that an Event Logging System (ELS) event occurred. The variable proElsSubSysEventMsg provides a textual description of the event. The variable is in one of two formats. If ELS timestamping is enabled, the format is hr:min:sec subsys_name.event_num: message_text. An example would be 09:32:56 IP.008: no rte 9.7.1.8 -> 9.7.4.3 dsc. If ELS timestamping is disabled, the format is subsys_name.event_num: message_text. An example would be IP.008: no rte 9.7.1.8 -> 9.7.4.3 dsc. | |||
| TRAP-TYPE | |||
| proElsSubSysEventMsg | |||
| mss8210PCAdapNumSlot | 1.3.6.1.4.1.2.6.118.2.2.1 | ||
| The number of PC adapter slots available for this stand-alone. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| mss8210PCAdapTable | 1.3.6.1.4.1.2.6.118.2.2.2 | ||
| A table of PC adapters entries. The number of entries is given by the value of mss8210PCAdapNumSlot. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| Mss8210PCAdapEntry | |||
| mss8210PCAdapEntry | 1.3.6.1.4.1.2.6.118.2.2.2.1 | ||
| A PC adapter entry containing objects to describe the operational aspects of the PC adapter on this stand-alone. | |||
| OBJECT-TYPE | |||
| Mss8210PCAdapEntry | |||
| mss8210PCAdapSlotNum | 1.3.6.1.4.1.2.6.118.2.2.2.1.1 | ||
| The relative slot location at which the adapter is attached to this stand-alone. The slots are numbered from 1 to 2 (left to right) when facing this stand-alone. This variable serves as the index for the mss8210PCAdapTable. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| mss8210PCAdapType | 1.3.6.1.4.1.2.6.118.2.2.2.1.2 | ||
| The type of PC adapter that is inserted into this slot. The variable shall assume a value of unknown(1) if the adapter in the slot is not supported by this stand-alone. The variable shall assume a value of harddrive(2) if the slot contains a PC disk drive. The variable shall assume a value of modem(3) if the slot contains a PC data/fax/voice modem. The variable shall assume a value of flashcard(5) if the slot contains a PC flash card. This variable shall assume a value of notPresent(4), when a PC card is not plugged into the corrisponding slot. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), harddrive(2), modem(3), notPresent(4), flashcard(5) | ||
| mss8210PCIAdapter | 1.3.6.1.4.1.2.6.118.2.3 | ||
| OBJECT IDENTIFIER | |||
| mss8210PCAdapTypeChg | 1.3.6.1.4.1.2.6.118.2.3 | ||
| The trap announces a change in the type of PC card. It shall be sent if the value of the mss8210PCAdapType changes and mss8210NotifyStatus has a value of enabled(1). | |||
| TRAP-TYPE | |||
| mss8210PCAdapType | |||
| mss8210PCIAdapNumSlot | 1.3.6.1.4.1.2.6.118.2.3.1 | ||
| The number of PCI adapter slots available for this stand-alone. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| mss8210PCIAdapTable | 1.3.6.1.4.1.2.6.118.2.3.2 | ||
| A table of PCI adapters entries. The number of entries is given by the value of mss8210PCIAdapNumSlot. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| Mss8210PCIAdapEntry | |||
| mss8210PCIAdapEntry | 1.3.6.1.4.1.2.6.118.2.3.2.1 | ||
| A PCI adapter entry containing objects to describe the operational aspects of the PCI adapter on this stand-alone. | |||
| OBJECT-TYPE | |||
| Mss8210PCIAdapEntry | |||
| mss8210PCIAdapSlotNum | 1.3.6.1.4.1.2.6.118.2.3.2.1.1 | ||
| The relative slot location at which the adapter is attached to this stand-alone. Slots are numbered from 1 to 2 (top to bottom) when facing this stand-alone. This variable serves as the index for the mss8210PCIAdapTable. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| mss8210PCIAdapType | 1.3.6.1.4.1.2.6.118.2.3.2.1.2 | ||
| The type of PCI adapter that is inserted into this slot. This variable shall assume a value of unknown(1) if the mss8210PCIAdapConfigType is not-configured(1) or if the mss8210PCIAdapConfigType is atm(2) and the mss8210PCIAdapOperStatus has a value of unknown(1), not-configured(2), not-present(3), unavailable(4), does-not_apply(5) or miss-configured(10). The variable shall assume a value of atm(2) if the mss8210PCIAdapConfigType has a value of atm(2) and the mss8210PCIAdapOperStatus has a value of enabled-pending(6), enabled(7), disabled-pending(8) or disabled(9). The variable shall assume a value of fddi(3) if the mss8210PCIAdapConfigType has a value of fddi(3) and the mss8210PCIAdapOperStatus has a value of enabled-pending(6), enabled(7), disabled-pending(8) or disabled(9). This variable shall assue a value of notPresent(4), when a PCI card is not plugged into the corrisponding slot. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), atm(2), fddi(3), notPresent(4) | ||
| mss8210PCIAdapConfigType | 1.3.6.1.4.1.2.6.118.2.3.2.1.3 | ||
| The router configuration type for this slot. The configuration type originates from the configuration tool used for this stand-alone. The variable shall assume a value of not-configured(1) if no configuration exist for this slot. The variable shall assume a value of atm(2) if the slot is configured for an ATM adapter. The variable shall assume a value of fddi(3) if the slot is configured for an FDDI adapter. | |||
| OBJECT-TYPE | |||
| INTEGER | not-configured(1), atm(2), fddi(3) | ||
| mss8210PCIAdapOperStatus | 1.3.6.1.4.1.2.6.118.2.3.2.1.4 | ||
| The operational status of this PCI adapter on this stand-alone. The variable shall assume a value of unknown(1) if the adapter inserted in the slot can not be recognized. The variable shall assume a value of not-configured(2) if the adapter inserted in the slot is recognized but no router configuration exists. The variable shall assume a value of not-present(3) if the adapter is not inserted in the slot but the router configuration exists. The variable shall assume a value of unavailable(4) if adapter inserted in the slot can not be used nor made ready to be used; for example, a hardware error. The variable shall assume a value of does-not-apply(5) if this adapter does not contain an operational state. The variable shall assume a value of enable-pending(6) if commands have been issued to enable the adapter but have not been completed. The variable shall assume a value of enabled(7) if commands have been successfully issued to enable the adapter. The variable shall assume a value of disable-pending(8) if commands have been issued to disable the adapter but have not been completed. The variable shall assume a value of disabled(9) if commands have been successfully issued to disable the adapter. The variable shall assume a value of miss-configured(10) if the adapter is inserted in the slot but the router configuration is of a different type. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), not-configured(2), not-present(3), unavailable(4), does-not-apply(5), enable-pending(6), enabled(7), disable-pending(8), disabled(9), miss-configured(10) | ||
| mss8210PCIAdapDiagStatus | 1.3.6.1.4.1.2.6.118.2.3.2.1.5 | ||
| The diagnostic status of this PCI adapter on this stand-alone. The variable shall assume a value of auto(1) if commands have been issued by the system to determine the status of the adapter; for example, at initialization. The variable shall assume a value of inactive(2) if the adapter is not currently running any diagnostics. The variable shall assume a value of idle(3) if the adapter is in the disabled operational state ready to run the diagnostics. The variable shall assume a value of active(4) if commands have been issued by the user to run the diagnostics. | |||
| OBJECT-TYPE | |||
| INTEGER | auto(1), inactive(2), idle(3), active(4) | ||
| mss8210PCIAdapNetworkStatus | 1.3.6.1.4.1.2.6.118.2.3.2.1.6 | ||
| The network status of this PCI adapter on this stand-alone. The variable shall assume a value of up(1) if the adapter is connected to the network. The variable shall assume a value of down(3) if the adapter can not verify a network connection. The variable shall assume a value of testing(4) if the adapter is running tests for the network connection. The variable shall assume a value of unknown(1) if network status can not be determined. The variable shall assume a value of does-not-apply(5) if the adapter does not contain a network state. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), up(2), down(3), testing(4), does-not-apply(5) | ||
| mss8210PCIAdapFaultStatus | 1.3.6.1.4.1.2.6.118.2.3.2.1.7 | ||
| The fault status of this PCI adapter on this stand-alone. The variable shall assume a value of no-fault(2) if no fault that is associated with this adapter has been detected. The variable shall assume a value of isolated(3) if this fault that can be isolated on the adapter itself. The variable shall assume a value of non-isolated(4) if the fault can not isolated on the adapter or in the network. The variable shall assume a value of unknown(1) if the fault status has not been determined; for example, at initialization. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), no-fault(2), isolated(3), non-isolated(4) | ||
| mss8210TempThresholdChg | 1.3.6.1.4.1.2.6.118.2.4 | ||
| The trap announces a change in the temperature of the stand-alone. It shall be sent if the value of the mss8210TempThreshold changes and mss8210NotifyStatus has a value of enabled(1). | |||
| TRAP-TYPE | |||
| mss8210TempThresholdStatus | |||
| mss8210PCIAdapStatusChg | 1.3.6.1.4.1.2.6.118.2.5 | ||
| The trap announces a change in the status of the PCI adapter. It shall be sent if the value of either mss8210PCIAdapConfigType, mss8210PCIAdapOperStatus, mss8210PCIAdapDiagStatus, mss8210PCIAdapNetworkStatus or mss8210PCIAdapFaultStatus changes and mss8210NotifyStatus has a value of enabled(1). | |||
| TRAP-TYPE | |||
| mss8210PCIAdapConfigType | |||
| mss8210PCIAdapOperStatus | |||
| mss8210PCIAdapDiagStatus | |||
| mss8210PCIAdapNetworkStatus | |||
| mss8210PCIAdapFaultStatus | |||
| Mss8210PCAdapEntry | |||
| SEQUENCE | |||
| INTEGER as mss8210PCAdapSlotNum | |||
| INTEGER as mss8210PCAdapType | |||
| Mss8210PCIAdapEntry | |||
| SEQUENCE | |||
| INTEGER as mss8210PCIAdapSlotNum | |||
| INTEGER as mss8210PCIAdapType | |||
| INTEGER as mss8210PCIAdapConfigType | |||
| INTEGER as mss8210PCIAdapOperStatus | |||
| INTEGER as mss8210PCIAdapDiagStatus | |||
| INTEGER as mss8210PCIAdapNetworkStatus | |||
| INTEGER as mss8210PCIAdapFaultStatus | |||