NAT-MIB

File: NAT-MIB.mib (89711 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB SNMP-FRAMEWORK-MIB INET-ADDRESS-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
Unsigned32 Gauge32 Counter64
TimeTicks mib-2 NOTIFICATION-TYPE
TEXTUAL-CONVENTION StorageType RowStatus
MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP
ifIndex ifCounterDiscontinuityGroup SnmpAdminString
InetAddressType InetAddress InetPortNumber

Defined Objects

natMIB 1.3.6.1.2.1.123
This MIB module defines the generic managed objects for NAT. Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC 4008; see the RFC itself for full legal notices.
MODULE-IDENTITY    

natMIBNotifications 1.3.6.1.2.1.123.0
OBJECT IDENTIFIER    

natPacketDiscard 1.3.6.1.2.1.123.0.1
This notification is generated when IP packets are discarded by the NAT function; e.g., due to lack of mapping space when NAT is out of addresses or ports. Note that the generation of natPacketDiscard notifications is throttled by the agent, as specified by the 'natNotifThrottlingInterval' object.
NOTIFICATION-TYPE    
  ifIndex  

natMIBObjects 1.3.6.1.2.1.123.1
OBJECT IDENTIFIER    

natDefTimeouts 1.3.6.1.2.1.123.1.1
OBJECT IDENTIFIER    

natBindDefIdleTimeout 1.3.6.1.2.1.123.1.1.1
The default Bind (Address Bind or Port Bind) idle timeout parameter. If the agent is capable of storing non-volatile configuration, then the value of this object must be restored after a re-initialization of the management system.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

natUdpDefIdleTimeout 1.3.6.1.2.1.123.1.1.2
The default UDP idle timeout parameter. If the agent is capable of storing non-volatile configuration, then the value of this object must be restored after a re-initialization of the management system.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

natIcmpDefIdleTimeout 1.3.6.1.2.1.123.1.1.3
The default ICMP idle timeout parameter. If the agent is capable of storing non-volatile configuration, then the value of this object must be restored after a re-initialization of the management system.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

natOtherDefIdleTimeout 1.3.6.1.2.1.123.1.1.4
The default idle timeout parameter for protocols represented by the value other (2) in NatProtocolType. If the agent is capable of storing non-volatile configuration, then the value of this object must be restored after a re-initialization of the management system.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

natTcpDefIdleTimeout 1.3.6.1.2.1.123.1.1.5
The default time interval that a NAT session for an established TCP connection is allowed to remain valid without any activity on the TCP connection. If the agent is capable of storing non-volatile configuration, then the value of this object must be restored after a re-initialization of the management system.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

natTcpDefNegTimeout 1.3.6.1.2.1.123.1.1.6
The default time interval that a NAT session for a TCP connection that is not in the established state is allowed to remain valid without any activity on the TCP connection. If the agent is capable of storing non-volatile configuration, then the value of this object must be restored after a re-initialization of the management system.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

natNotifCtrl 1.3.6.1.2.1.123.1.2
OBJECT IDENTIFIER    

natNotifThrottlingInterval 1.3.6.1.2.1.123.1.2.1
This object controls the generation of the natPacketDiscard notification. If this object has a value of zero, then no natPacketDiscard notifications will be transmitted by the agent. If this object has a non-zero value, then the agent must not generate more than one natPacketDiscard 'notification-event' in the indicated period, where a 'notification-event' is the generation of a single notification PDU type to a list of notification destinations. If additional NAT packets are discarded within the throttling period, then notification-events for these changes must be suppressed by the agent until the current throttling period expires. If natNotifThrottlingInterval notification generation is enabled, the suggested default throttling period is 60 seconds, but generation of the natPacketDiscard notification should be disabled by default. If the agent is capable of storing non-volatile configuration, then the value of this object must be restored after a re-initialization of the management system. The actual transmission of notifications is controlled via the MIB modules in RFC 3413.
OBJECT-TYPE    
  Integer32 0 | 5..3600  

natInterfaceTable 1.3.6.1.2.1.123.1.3
This table specifies the attributes for interfaces on a device supporting NAT function.
OBJECT-TYPE    
  SEQUENCE OF  
    NatInterfaceEntry

natInterfaceEntry 1.3.6.1.2.1.123.1.3.1
Each entry in the natInterfaceTable holds a set of parameters for an interface, instantiated by ifIndex. Therefore, the interface index must have been assigned, according to the applicable procedures, before it can be meaningfully used. Generally, this means that the interface must exist. When natStorageType is of type nonVolatile, however, this may reflect the configuration for an interface whose ifIndex has been assigned but for which the supporting implementation is not currently present.
OBJECT-TYPE    
  NatInterfaceEntry  

natInterfaceRealm 1.3.6.1.2.1.123.1.3.1.1
This object identifies whether this interface is connected to the private or the public realm.
OBJECT-TYPE    
  INTEGER private(1), public(2)  

natInterfaceServiceType 1.3.6.1.2.1.123.1.3.1.2
An indication of the direction in which new sessions are permitted and the extent of translation done within the IP and transport headers.
OBJECT-TYPE    
  BITS basicNat(0), napt(1), bidirectionalNat(2), twiceNat(3)  

natInterfaceInTranslates 1.3.6.1.2.1.123.1.3.1.3
Number of packets received on this interface that were translated. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of ifCounterDiscontinuityTime on the relevant interface.
OBJECT-TYPE    
  Counter64  

natInterfaceOutTranslates 1.3.6.1.2.1.123.1.3.1.4
Number of translated packets that were sent out this interface. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of ifCounterDiscontinuityTime on the relevant interface.
OBJECT-TYPE    
  Counter64  

natInterfaceDiscards 1.3.6.1.2.1.123.1.3.1.5
Number of packets that had to be rejected/dropped due to a lack of resources for this interface. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of ifCounterDiscontinuityTime on the relevant interface.
OBJECT-TYPE    
  Counter64  

natInterfaceStorageType 1.3.6.1.2.1.123.1.3.1.6
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
OBJECT-TYPE    
  StorageType  

natInterfaceRowStatus 1.3.6.1.2.1.123.1.3.1.7
The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the natInterfaceRowStatus column is 'notReady'. In particular, a newly created row cannot be made active until the corresponding instance of natInterfaceServiceType has been set. None of the objects in this row may be modified while the value of this object is active(1).
OBJECT-TYPE    
  RowStatus  

natAddrMapTable 1.3.6.1.2.1.123.1.4
This table lists address map parameters for NAT.
OBJECT-TYPE    
  SEQUENCE OF  
    NatAddrMapEntry

natAddrMapEntry 1.3.6.1.2.1.123.1.4.1
This entry represents an address map to be used for NAT and contributes to the dynamic and/or static address mapping tables of the NAT device.
OBJECT-TYPE    
  NatAddrMapEntry  

natAddrMapIndex 1.3.6.1.2.1.123.1.4.1.1
Along with ifIndex, this object uniquely identifies an entry in the natAddrMapTable. Address map entries are applied in the order specified by natAddrMapIndex.
OBJECT-TYPE    
  NatAddrMapId  

natAddrMapName 1.3.6.1.2.1.123.1.4.1.2
Name identifying all map entries in the table associated with the same interface. All map entries with the same ifIndex MUST have the same map name.
OBJECT-TYPE    
  SnmpAdminString SIZE(1..32)  

natAddrMapEntryType 1.3.6.1.2.1.123.1.4.1.3
This parameter can be used to set up static or dynamic address maps.
OBJECT-TYPE    
  NatAssociationType  

natAddrMapTranslationEntity 1.3.6.1.2.1.123.1.4.1.4
The end-point entity (source or destination) in inbound or outbound sessions (i.e., first packets) that may be translated by an address map entry. Session direction (inbound or outbound) is derived from the direction of the first packet of a session traversing a NAT interface. NAT address (and Transport-ID) maps may be defined to effect inbound or outbound sessions. Traditionally, address maps for Basic NAT and NAPT are configured on a public interface for outbound sessions, effecting translation of source end-point. The value of this object must be set to outboundSrcEndPoint for those interfaces. Alternately, if address maps for Basic NAT and NAPT were to be configured on a private interface, the desired value for this object for the map entries would be inboundSrcEndPoint (i.e., effecting translation of source end-point for inbound sessions). If TwiceNAT were to be configured on a private interface, the desired value for this object for the map entries would be a bitmask of inboundSrcEndPoint and inboundDstEndPoint.
OBJECT-TYPE    
  NatTranslationEntity  

natAddrMapLocalAddrType 1.3.6.1.2.1.123.1.4.1.5
This object specifies the address type used for natAddrMapLocalAddrFrom and natAddrMapLocalAddrTo.
OBJECT-TYPE    
  InetAddressType  

natAddrMapLocalAddrFrom 1.3.6.1.2.1.123.1.4.1.6
This object specifies the first IP address of the range of IP addresses mapped by this translation entry. The value of this object must be less than or equal to the value of the natAddrMapLocalAddrTo object. The type of this address is determined by the value of the natAddrMapLocalAddrType object.
OBJECT-TYPE    
  InetAddress  

natAddrMapLocalAddrTo 1.3.6.1.2.1.123.1.4.1.7
This object specifies the last IP address of the range of IP addresses mapped by this translation entry. If only a single address is being mapped, the value of this object is equal to the value of natAddrMapLocalAddrFrom. For a static NAT, the number of addresses in the range defined by natAddrMapLocalAddrFrom and natAddrMapLocalAddrTo must be equal to the number of addresses in the range defined by natAddrMapGlobalAddrFrom and natAddrMapGlobalAddrTo. The value of this object must be greater than or equal to the value of the natAddrMapLocalAddrFrom object. The type of this address is determined by the value of the natAddrMapLocalAddrType object.
OBJECT-TYPE    
  InetAddress  

natAddrMapLocalPortFrom 1.3.6.1.2.1.123.1.4.1.8
If this conceptual row describes a Basic NAT address mapping, then the value of this object must be zero. If this conceptual row describes NAPT, then the value of this object specifies the first port number in the range of ports being mapped. The value of this object must be less than or equal to the value of the natAddrMapLocalPortTo object. If the translation specifies a single port, then the value of this object is equal to the value of natAddrMapLocalPortTo.
OBJECT-TYPE    
  InetPortNumber  

natAddrMapLocalPortTo 1.3.6.1.2.1.123.1.4.1.9
If this conceptual row describes a Basic NAT address mapping, then the value of this object must be zero. If this conceptual row describes NAPT, then the value of this object specifies the last port number in the range of ports being mapped. The value of this object must be greater than or equal to the value of the natAddrMapLocalPortFrom object. If the translation specifies a single port, then the value of this object is equal to the value of natAddrMapLocalPortFrom.
OBJECT-TYPE    
  InetPortNumber  

natAddrMapGlobalAddrType 1.3.6.1.2.1.123.1.4.1.10
This object specifies the address type used for natAddrMapGlobalAddrFrom and natAddrMapGlobalAddrTo.
OBJECT-TYPE    
  InetAddressType  

natAddrMapGlobalAddrFrom 1.3.6.1.2.1.123.1.4.1.11
This object specifies the first IP address of the range of IP addresses being mapped to. The value of this object must be less than or equal to the value of the natAddrMapGlobalAddrTo object. The type of this address is determined by the value of the natAddrMapGlobalAddrType object.
OBJECT-TYPE    
  InetAddress  

natAddrMapGlobalAddrTo 1.3.6.1.2.1.123.1.4.1.12
This object specifies the last IP address of the range of IP addresses being mapped to. If only a single address is being mapped to, the value of this object is equal to the value of natAddrMapGlobalAddrFrom. For a static NAT, the number of addresses in the range defined by natAddrMapGlobalAddrFrom and natAddrMapGlobalAddrTo must be equal to the number of addresses in the range defined by natAddrMapLocalAddrFrom and natAddrMapLocalAddrTo. The value of this object must be greater than or equal to the value of the natAddrMapGlobalAddrFrom object. The type of this address is determined by the value of the natAddrMapGlobalAddrType object.
OBJECT-TYPE    
  InetAddress  

natAddrMapGlobalPortFrom 1.3.6.1.2.1.123.1.4.1.13
If this conceptual row describes a Basic NAT address mapping, then the value of this object must be zero. If this conceptual row describes NAPT, then the value of this object specifies the first port number in the range of ports being mapped to. The value of this object must be less than or equal to the value of the natAddrMapGlobalPortTo object. If the translation specifies a single port, then the value of this object is equal to the value natAddrMapGlobalPortTo.
OBJECT-TYPE    
  InetPortNumber  

natAddrMapGlobalPortTo 1.3.6.1.2.1.123.1.4.1.14
If this conceptual row describes a Basic NAT address mapping, then the value of this object must be zero. If this conceptual row describes NAPT, then the value of this object specifies the last port number in the range of ports being mapped to. The value of this object must be greater than or equal to the value of the natAddrMapGlobalPortFrom object. If the translation specifies a single port, then the value of this object is equal to the value of natAddrMapGlobalPortFrom.
OBJECT-TYPE    
  InetPortNumber  

natAddrMapProtocol 1.3.6.1.2.1.123.1.4.1.15
This object specifies a bitmap of protocol identifiers.
OBJECT-TYPE    
  NatProtocolMap  

natAddrMapInTranslates 1.3.6.1.2.1.123.1.4.1.16
The number of inbound packets pertaining to this address map entry that were translated. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface.
OBJECT-TYPE    
  Counter64  

natAddrMapOutTranslates 1.3.6.1.2.1.123.1.4.1.17
The number of outbound packets pertaining to this address map entry that were translated. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface.
OBJECT-TYPE    
  Counter64  

natAddrMapDiscards 1.3.6.1.2.1.123.1.4.1.18
The number of packets pertaining to this address map entry that were dropped due to lack of addresses in the address pool identified by this address map. The value of this object must always be zero in case of static address map. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface.
OBJECT-TYPE    
  Counter64  

natAddrMapAddrUsed 1.3.6.1.2.1.123.1.4.1.19
The number of addresses pertaining to this address map that are currently being used from the NAT pool. The value of this object must always be zero in the case of a static address map.
OBJECT-TYPE    
  Gauge32  

natAddrMapStorageType 1.3.6.1.2.1.123.1.4.1.20
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
OBJECT-TYPE    
  StorageType  

natAddrMapRowStatus 1.3.6.1.2.1.123.1.4.1.21
The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the natAddrMapRowStatus column is 'notReady'. None of the objects in this row may be modified while the value of this object is active(1).
OBJECT-TYPE    
  RowStatus  

natAddrBindNumberOfEntries 1.3.6.1.2.1.123.1.5
This object maintains a count of the number of entries that currently exist in the natAddrBindTable.
OBJECT-TYPE    
  Gauge32  

natAddrBindTable 1.3.6.1.2.1.123.1.6
This table holds information about the currently active NAT BINDs.
OBJECT-TYPE    
  SEQUENCE OF  
    NatAddrBindEntry

natAddrBindEntry 1.3.6.1.2.1.123.1.6.1
Each entry in this table holds information about an active address BIND. These entries are lost upon agent restart. This row has indexing which may create variables with more than 128 subidentifiers. Implementers of this table must be careful not to create entries that would result in OIDs which exceed the 128 subidentifier limit. Otherwise, the information cannot be accessed using SNMPv1, SNMPv2c or SNMPv3.
OBJECT-TYPE    
  NatAddrBindEntry  

natAddrBindLocalAddrType 1.3.6.1.2.1.123.1.6.1.1
This object specifies the address type used for natAddrBindLocalAddr.
OBJECT-TYPE    
  InetAddressType  

natAddrBindLocalAddr 1.3.6.1.2.1.123.1.6.1.2
This object represents the private-realm specific network layer address, which maps to the public-realm address represented by natAddrBindGlobalAddr. The type of this address is determined by the value of the natAddrBindLocalAddrType object.
OBJECT-TYPE    
  InetAddress  

natAddrBindGlobalAddrType 1.3.6.1.2.1.123.1.6.1.3
This object specifies the address type used for natAddrBindGlobalAddr.
OBJECT-TYPE    
  InetAddressType  

natAddrBindGlobalAddr 1.3.6.1.2.1.123.1.6.1.4
This object represents the public-realm network layer address that maps to the private-realm network layer address represented by natAddrBindLocalAddr. The type of this address is determined by the value of the natAddrBindGlobalAddrType object.
OBJECT-TYPE    
  InetAddress  

natAddrBindId 1.3.6.1.2.1.123.1.6.1.5
This object represents a bind id that is dynamically assigned to each bind by a NAT enabled device. Each bind is represented by a bind id that is unique across both, the natAddrBindTable and the natAddrPortBindTable.
OBJECT-TYPE    
  NatBindId  

natAddrBindTranslationEntity 1.3.6.1.2.1.123.1.6.1.6
This object represents the direction of sessions for which this bind is applicable and the endpoint entity (source or destination) within the sessions that is subject to translation using the BIND. Orientation of the bind can be a superset of translationEntity of the address map entry which forms the basis for this bind. For example, if the translationEntity of an address map entry is outboundSrcEndPoint, the translationEntity of a bind derived from this map entry may either be outboundSrcEndPoint or it may be bidirectional (a bitmask of outboundSrcEndPoint and inboundDstEndPoint).
OBJECT-TYPE    
  NatTranslationEntity  

natAddrBindType 1.3.6.1.2.1.123.1.6.1.7
This object indicates whether the bind is static or dynamic.
OBJECT-TYPE    
  NatAssociationType  

natAddrBindMapIndex 1.3.6.1.2.1.123.1.6.1.8
This object is a pointer to the natAddrMapTable entry (and the parameters of that entry) which was used in creating this BIND. This object, in conjunction with the ifIndex (which identifies a unique addrMapName) points to a unique entry in the natAddrMapTable.
OBJECT-TYPE    
  NatAddrMapId  

natAddrBindSessions 1.3.6.1.2.1.123.1.6.1.9
Number of sessions currently using this BIND.
OBJECT-TYPE    
  Gauge32  

natAddrBindMaxIdleTime 1.3.6.1.2.1.123.1.6.1.10
This object indicates the maximum time for which this bind can be idle with no sessions attached to it. The value of this object is of relevance only for dynamic NAT.
OBJECT-TYPE    
  TimeTicks  

natAddrBindCurrentIdleTime 1.3.6.1.2.1.123.1.6.1.11
At any given instance, this object indicates the time that this bind has been idle without any sessions attached to it. The value of this object is of relevance only for dynamic NAT.
OBJECT-TYPE    
  TimeTicks  

natAddrBindInTranslates 1.3.6.1.2.1.123.1.6.1.12
The number of inbound packets that were successfully translated by using this bind entry. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface.
OBJECT-TYPE    
  Counter64  

natAddrBindOutTranslates 1.3.6.1.2.1.123.1.6.1.13
The number of outbound packets that were successfully translated using this bind entry. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of ifCounterDiscontinuityTime on the relevant interface.
OBJECT-TYPE    
  Counter64  

natAddrPortBindNumberOfEntries 1.3.6.1.2.1.123.1.7
This object maintains a count of the number of entries that currently exist in the natAddrPortBindTable.
OBJECT-TYPE    
  Gauge32  

natAddrPortBindTable 1.3.6.1.2.1.123.1.8
This table holds information about the currently active NAPT BINDs.
OBJECT-TYPE    
  SEQUENCE OF  
    NatAddrPortBindEntry

natAddrPortBindEntry 1.3.6.1.2.1.123.1.8.1
Each entry in the this table holds information about a NAPT bind that is currently active. These entries are lost upon agent restart. This row has indexing which may create variables with more than 128 subidentifiers. Implementers of this table must be careful not to create entries which would result in OIDs that exceed the 128 subidentifier limit. Otherwise, the information cannot be accessed using SNMPv1, SNMPv2c or SNMPv3.
OBJECT-TYPE    
  NatAddrPortBindEntry  

natAddrPortBindLocalAddrType 1.3.6.1.2.1.123.1.8.1.1
This object specifies the address type used for natAddrPortBindLocalAddr.
OBJECT-TYPE    
  InetAddressType  

natAddrPortBindLocalAddr 1.3.6.1.2.1.123.1.8.1.2
This object represents the private-realm specific network layer address which, in conjunction with natAddrPortBindLocalPort, maps to the public-realm network layer address and transport id represented by natAddrPortBindGlobalAddr and natAddrPortBindGlobalPort respectively. The type of this address is determined by the value of the natAddrPortBindLocalAddrType object.
OBJECT-TYPE    
  InetAddress  

natAddrPortBindLocalPort 1.3.6.1.2.1.123.1.8.1.3
For a protocol value TCP or UDP, this object represents the private-realm specific port number. On the other hand, for ICMP a bind is created only for query/response type ICMP messages such as ICMP echo, Timestamp, and Information request messages, and this object represents the private-realm in specific identifier in the ICMP message, as defined in RFC 792 for ICMPv4 and in RFC 2463 for ICMPv6. This object object, together with natAddrPortBindProtocol, natAddrPortBindLocalAddrType, and natAddrPortBindLocalAddr, constitutes a session endpoint in the private realm. A bind entry binds a private realm specific endpoint to a public realm specific endpoint, as represented by the tuple of (natAddPortBindGlobalPort, natAddrPortBindProtocol, natAddrPortBindGlobalAddrType, and natAddrPortBindGlobalAddr).
OBJECT-TYPE    
  InetPortNumber  

natAddrPortBindProtocol 1.3.6.1.2.1.123.1.8.1.4
This object specifies a protocol identifier. If the value of this object is none(1), then this bind entry applies to all IP traffic. Any other value of this object specifies the class of IP traffic to which this BIND applies.
OBJECT-TYPE    
  NatProtocolType  

natAddrPortBindGlobalAddrType 1.3.6.1.2.1.123.1.8.1.5
This object specifies the address type used for natAddrPortBindGlobalAddr.
OBJECT-TYPE    
  InetAddressType  

natAddrPortBindGlobalAddr 1.3.6.1.2.1.123.1.8.1.6
This object represents the public-realm specific network layer address that, in conjunction with natAddrPortBindGlobalPort, maps to the private-realm network layer address and transport id represented by natAddrPortBindLocalAddr and natAddrPortBindLocalPort, respectively. The type of this address is determined by the value of the natAddrPortBindGlobalAddrType object.
OBJECT-TYPE    
  InetAddress  

natAddrPortBindGlobalPort 1.3.6.1.2.1.123.1.8.1.7
For a protocol value TCP or UDP, this object represents the public-realm specific port number. On the other hand, for ICMP a bind is created only for query/response type ICMP messages such as ICMP echo, Timestamp, and Information request messages, and this object represents the public-realm specific identifier in the ICMP message, as defined in RFC 792 for ICMPv4 and in RFC 2463 for ICMPv6. This object, together with natAddrPortBindProtocol, natAddrPortBindGlobalAddrType, and natAddrPortBindGlobalAddr, constitutes a session endpoint in the public realm. A bind entry binds a public realm specific endpoint to a private realm specific endpoint, as represented by the tuple of (natAddPortBindLocalPort, natAddrPortBindProtocol, natAddrPortBindLocalAddrType, and natAddrPortBindLocalAddr).
OBJECT-TYPE    
  InetPortNumber  

natAddrPortBindId 1.3.6.1.2.1.123.1.8.1.8
This object represents a bind id that is dynamically assigned to each bind by a NAT enabled device. Each bind is represented by a unique bind id across both the natAddrBindTable and the natAddrPortBindTable.
OBJECT-TYPE    
  NatBindId  

natAddrPortBindTranslationEntity 1.3.6.1.2.1.123.1.8.1.9
This object represents the direction of sessions for which this bind is applicable and the entity (source or destination) within the sessions that is subject to translation with the BIND. Orientation of the bind can be a superset of the translationEntity of the address map entry that forms the basis for this bind. For example, if the translationEntity of an address map entry is outboundSrcEndPoint, the translationEntity of a bind derived from this map entry may either be outboundSrcEndPoint or may be bidirectional (a bitmask of outboundSrcEndPoint and inboundDstEndPoint).
OBJECT-TYPE    
  NatTranslationEntity  

natAddrPortBindType 1.3.6.1.2.1.123.1.8.1.10
This object indicates whether the bind is static or dynamic.
OBJECT-TYPE    
  NatAssociationType  

natAddrPortBindMapIndex 1.3.6.1.2.1.123.1.8.1.11
This object is a pointer to the natAddrMapTable entry (and the parameters of that entry) used in creating this BIND. This object, in conjunction with the ifIndex (which identifies a unique addrMapName), points to a unique entry in the natAddrMapTable.
OBJECT-TYPE    
  NatAddrMapId  

natAddrPortBindSessions 1.3.6.1.2.1.123.1.8.1.12
Number of sessions currently using this BIND.
OBJECT-TYPE    
  Gauge32  

natAddrPortBindMaxIdleTime 1.3.6.1.2.1.123.1.8.1.13
This object indicates the maximum time for which this bind can be idle without any sessions attached to it. The value of this object is of relevance only for dynamic NAT.
OBJECT-TYPE    
  TimeTicks  

natAddrPortBindCurrentIdleTime 1.3.6.1.2.1.123.1.8.1.14
At any given instance, this object indicates the time that this bind has been idle without any sessions attached to it. The value of this object is of relevance only for dynamic NAT.
OBJECT-TYPE    
  TimeTicks  

natAddrPortBindInTranslates 1.3.6.1.2.1.123.1.8.1.15
The number of inbound packets that were translated as per this bind entry. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface.
OBJECT-TYPE    
  Counter64  

natAddrPortBindOutTranslates 1.3.6.1.2.1.123.1.8.1.16
The number of outbound packets that were translated as per this bind entry. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface.
OBJECT-TYPE    
  Counter64  

natSessionTable 1.3.6.1.2.1.123.1.9
The (conceptual) table containing one entry for each NAT session currently active on this NAT device.
OBJECT-TYPE    
  SEQUENCE OF  
    NatSessionEntry

natSessionEntry 1.3.6.1.2.1.123.1.9.1
An entry (conceptual row) containing information about an active NAT session on this NAT device. These entries are lost upon agent restart.
OBJECT-TYPE    
  NatSessionEntry  

natSessionIndex 1.3.6.1.2.1.123.1.9.1.1
The session ID for this NAT session.
OBJECT-TYPE    
  NatSessionId  

natSessionPrivateSrcEPBindId 1.3.6.1.2.1.123.1.9.1.2
The bind id associated between private and public source end points. In the case of Symmetric-NAT, this should be set to zero.
OBJECT-TYPE    
  NatBindIdOrZero  

natSessionPrivateSrcEPBindMode 1.3.6.1.2.1.123.1.9.1.3
This object indicates whether the bind indicated by the object natSessionPrivateSrcEPBindId is an address bind or an address port bind.
OBJECT-TYPE    
  NatBindMode  

natSessionPrivateDstEPBindId 1.3.6.1.2.1.123.1.9.1.4
The bind id associated between private and public destination end points.
OBJECT-TYPE    
  NatBindIdOrZero  

natSessionPrivateDstEPBindMode 1.3.6.1.2.1.123.1.9.1.5
This object indicates whether the bind indicated by the object natSessionPrivateDstEPBindId is an address bind or an address port bind.
OBJECT-TYPE    
  NatBindMode  

natSessionDirection 1.3.6.1.2.1.123.1.9.1.6
The direction of this session with respect to the local network. 'inbound' indicates that this session was initiated from the public network into the private network. 'outbound' indicates that this session was initiated from the private network into the public network.
OBJECT-TYPE    
  INTEGER inbound(1), outbound(2)  

natSessionUpTime 1.3.6.1.2.1.123.1.9.1.7
The up time of this session in one-hundredths of a second.
OBJECT-TYPE    
  TimeTicks  

natSessionAddrMapIndex 1.3.6.1.2.1.123.1.9.1.8
This object is a pointer to the natAddrMapTable entry (and the parameters of that entry) used in creating this session. This object, in conjunction with the ifIndex (which identifies a unique addrMapName), points to a unique entry in the natAddrMapTable.
OBJECT-TYPE    
  NatAddrMapId  

natSessionProtocolType 1.3.6.1.2.1.123.1.9.1.9
The protocol type of this session.
OBJECT-TYPE    
  NatProtocolType  

natSessionPrivateAddrType 1.3.6.1.2.1.123.1.9.1.10
This object specifies the address type used for natSessionPrivateSrcAddr and natSessionPrivateDstAddr.
OBJECT-TYPE    
  InetAddressType  

natSessionPrivateSrcAddr 1.3.6.1.2.1.123.1.9.1.11
The source IP address of the session endpoint that lies in the private network. The value of this object must be zero only when the natSessionPrivateSrcEPBindId object has a zero value. When the value of this object is zero, the NAT session lookup will match any IP address to this field. The type of this address is determined by the value of the natSessionPrivateAddrType object.
OBJECT-TYPE    
  InetAddress  

natSessionPrivateSrcPort 1.3.6.1.2.1.123.1.9.1.12
When the value of protocol is TCP or UDP, this object represents the source port in the first packet of session while in private-realm. On the other hand, when the protocol is ICMP, a NAT session is created only for query/response type ICMP messages such as ICMP echo, Timestamp, and Information request messages, and this object represents the private-realm specific identifier in the ICMP message, as defined in RFC 792 for ICMPv4 and in RFC 2463 for ICMPv6. The value of this object must be zero when the natSessionPrivateSrcEPBindId object has zero value and value of natSessionPrivateSrcEPBindMode is addressPortBind(2). In such a case, the NAT session lookup will match any port number to this field. The value of this object must be zero when the object is not a representative field (SrcPort, DstPort, or ICMP identifier) of the session tuple in either the public realm or the private realm.
OBJECT-TYPE    
  InetPortNumber  

natSessionPrivateDstAddr 1.3.6.1.2.1.123.1.9.1.13
The destination IP address of the session endpoint that lies in the private network. The value of this object must be zero when the natSessionPrivateDstEPBindId object has a zero value. In such a scenario, the NAT session lookup will match any IP address to this field. The type of this address is determined by the value of the natSessionPrivateAddrType object.
OBJECT-TYPE    
  InetAddress  

natSessionPrivateDstPort 1.3.6.1.2.1.123.1.9.1.14
When the value of protocol is TCP or UDP, this object represents the destination port in the first packet of session while in private-realm. On the other hand, when the protocol is ICMP, this object is not relevant and should be set to zero. The value of this object must be zero when the natSessionPrivateDstEPBindId object has a zero value and natSessionPrivateDstEPBindMode is set to addressPortBind(2). In such a case, the NAT session lookup will match any port number to this field. The value of this object must be zero when the object is not a representative field (SrcPort, DstPort, or ICMP identifier) of the session tuple in either the public realm or the private realm.
OBJECT-TYPE    
  InetPortNumber  

natSessionPublicAddrType 1.3.6.1.2.1.123.1.9.1.15
This object specifies the address type used for natSessionPublicSrcAddr and natSessionPublicDstAddr.
OBJECT-TYPE    
  InetAddressType  

natSessionPublicSrcAddr 1.3.6.1.2.1.123.1.9.1.16
The source IP address of the session endpoint that lies in the public network. The value of this object must be zero when the natSessionPrivateSrcEPBindId object has a zero value. In such a scenario, the NAT session lookup will match any IP address to this field. The type of this address is determined by the value of the natSessionPublicAddrType object.
OBJECT-TYPE    
  InetAddress  

natSessionPublicSrcPort 1.3.6.1.2.1.123.1.9.1.17
When the value of protocol is TCP or UDP, this object represents the source port in the first packet of session while in public-realm. On the other hand, when protocol is ICMP, a NAT session is created only for query/response type ICMP messages such as ICMP echo, Timestamp, and Information request messages, and this object represents the public-realm specific identifier in the ICMP message, as defined in RFC 792 for ICMPv4 and in RFC 2463 for ICMPv6. The value of this object must be zero when the natSessionPrivateSrcEPBindId object has a zero value and natSessionPrivateSrcEPBindMode is set to addressPortBind(2). In such a scenario, the NAT session lookup will match any port number to this field. The value of this object must be zero when the object is not a representative field (SrcPort, DstPort or ICMP identifier) of the session tuple in either the public realm or the private realm.
OBJECT-TYPE    
  InetPortNumber  

natSessionPublicDstAddr 1.3.6.1.2.1.123.1.9.1.18
The destination IP address of the session endpoint that lies in the public network. The value of this object must be non-zero when the natSessionPrivateDstEPBindId object has a non-zero value. If the value of this object and the corresponding natSessionPrivateDstEPBindId object value is zero, then the NAT session lookup will match any IP address to this field. The type of this address is determined by the value of the natSessionPublicAddrType object.
OBJECT-TYPE    
  InetAddress  

natSessionPublicDstPort 1.3.6.1.2.1.123.1.9.1.19
When the value of protocol is TCP or UDP, this object represents the destination port in the first packet of session while in public-realm. On the other hand, when the protocol is ICMP, this object is not relevant for translation and should be zero. The value of this object must be zero when the natSessionPrivateDstEPBindId object has a zero value and natSessionPrivateDstEPBindMode is addressPortBind(2). In such a scenario, the NAT session lookup will match any port number to this field. The value of this object must be zero when the object is not a representative field (SrcPort, DstPort, or ICMP identifier) of the session tuple in either the public realm or the private realm.
OBJECT-TYPE    
  InetPortNumber  

natSessionMaxIdleTime 1.3.6.1.2.1.123.1.9.1.20
The max time for which this session can be idle without detecting a packet.
OBJECT-TYPE    
  TimeTicks  

natSessionCurrentIdleTime 1.3.6.1.2.1.123.1.9.1.21
The time since a packet belonging to this session was last detected.
OBJECT-TYPE    
  TimeTicks  

natSessionInTranslates 1.3.6.1.2.1.123.1.9.1.22
The number of inbound packets that were translated for this session. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface.
OBJECT-TYPE    
  Counter64  

natSessionOutTranslates 1.3.6.1.2.1.123.1.9.1.23
The number of outbound packets that were translated for this session. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface.
OBJECT-TYPE    
  Counter64  

natProtocolTable 1.3.6.1.2.1.123.1.10
The (conceptual) table containing per protocol NAT statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    NatProtocolEntry

natProtocolEntry 1.3.6.1.2.1.123.1.10.1
An entry (conceptual row) containing NAT statistics pertaining to a particular protocol.
OBJECT-TYPE    
  NatProtocolEntry  

natProtocol 1.3.6.1.2.1.123.1.10.1.1
This object represents the protocol pertaining to which parameters are reported.
OBJECT-TYPE    
  NatProtocolType  

natProtocolInTranslates 1.3.6.1.2.1.123.1.10.1.2
The number of inbound packets pertaining to the protocol identified by natProtocol that underwent NAT. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface.
OBJECT-TYPE    
  Counter64  

natProtocolOutTranslates 1.3.6.1.2.1.123.1.10.1.3
The number of outbound packets pertaining to the protocol identified by natProtocol that underwent NAT. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface.
OBJECT-TYPE    
  Counter64  

natProtocolDiscards 1.3.6.1.2.1.123.1.10.1.4
The number of packets pertaining to the protocol identified by natProtocol that had to be rejected/dropped due to lack of resources. These rejections could be due to session timeout, resource unavailability, lack of address space, etc. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface.
OBJECT-TYPE    
  Counter64  

natMIBConformance 1.3.6.1.2.1.123.2
OBJECT IDENTIFIER    

natMIBGroups 1.3.6.1.2.1.123.2.1
OBJECT IDENTIFIER    

natConfigGroup 1.3.6.1.2.1.123.2.1.1
A collection of configuration-related information required to support management of devices supporting NAT.
OBJECT-GROUP    

natTranslationGroup 1.3.6.1.2.1.123.2.1.2
A collection of BIND-related objects required to support management of devices supporting NAT.
OBJECT-GROUP    

natStatsInterfaceGroup 1.3.6.1.2.1.123.2.1.3
A collection of NAT statistics associated with the interface on which NAT is configured, to aid troubleshooting/monitoring of the NAT operation.
OBJECT-GROUP    

natStatsProtocolGroup 1.3.6.1.2.1.123.2.1.4
A collection of protocol specific NAT statistics, to aid troubleshooting/monitoring of NAT operation.
OBJECT-GROUP    

natStatsAddrMapGroup 1.3.6.1.2.1.123.2.1.5
A collection of address map specific NAT statistics, to aid troubleshooting/monitoring of NAT operation.
OBJECT-GROUP    

natMIBNotificationGroup 1.3.6.1.2.1.123.2.1.6
A collection of notifications generated by devices supporting this MIB.
NOTIFICATION-GROUP    

natMIBCompliances 1.3.6.1.2.1.123.2.2
OBJECT IDENTIFIER    

natMIBFullCompliance 1.3.6.1.2.1.123.2.2.1
When this MIB is implemented with support for read-create, then such an implementation can claim full compliance. Such devices can then be both monitored and configured with this MIB. The following index objects cannot be added as OBJECT clauses but nevertheless have the compliance requirements:
MODULE-COMPLIANCE    

natMIBReadOnlyCompliance 1.3.6.1.2.1.123.2.2.2
When this MIB is implemented without support for read-create (i.e., in read-only mode), then such an implementation can claim read-only compliance. Such a device can then be monitored but cannot be configured with this MIB. The following index objects cannot be added as OBJECT clauses but nevertheless have the compliance requirements:
MODULE-COMPLIANCE    

Defined Objects

NatProtocolType  
A list of protocols that support the network address translation. Inclusion of the values is not intended to imply that those protocols need to be supported. Any change in this TEXTUAL-CONVENTION should also be reflected in the definition of NatProtocolMap, which is a BITS representation of this.
TEXTUAL-CONVENTION    
  INTEGER none(1), other(2), icmp(3), udp(4), tcp(5)  

NatProtocolMap  
A bitmap of protocol identifiers that support the network address translation. Any change in this TEXTUAL-CONVENTION should also be reflected in the definition of NatProtocolType.
TEXTUAL-CONVENTION    
  BITS other(0), icmp(1), udp(2), tcp(3)  

NatAddrMapId  
A unique id that is assigned to each address map by a NAT enabled device.
TEXTUAL-CONVENTION    
  Unsigned32 1..4294967295  

NatBindIdOrZero  
A unique id that is assigned to each bind by a NAT enabled device. The bind id will be zero in the case of a Symmetric NAT.
TEXTUAL-CONVENTION    
  Unsigned32 0..4294967295  

NatBindId  
A unique id that is assigned to each bind by a NAT enabled device.
TEXTUAL-CONVENTION    
  Unsigned32 1..4294967295  

NatSessionId  
A unique id that is assigned to each session by a NAT enabled device.
TEXTUAL-CONVENTION    
  Unsigned32 1..4294967295  

NatBindMode  
An indication of whether the bind is an address bind or an address port bind.
TEXTUAL-CONVENTION    
  INTEGER addressBind(1), addressPortBind(2)  

NatAssociationType  
An indication of whether the association is static or dynamic.
TEXTUAL-CONVENTION    
  INTEGER static(1), dynamic(2)  

NatTranslationEntity  
An indication of a) the direction of a session for which an address map entry, address bind or port bind is applicable, and b) the entity (source or destination) within the session that is subject to translation.
TEXTUAL-CONVENTION    
  BITS inboundSrcEndPoint(0), outboundDstEndPoint(1), inboundDstEndPoint(2), outboundSrcEndPoint(3)  

NatInterfaceEntry  
SEQUENCE    
  INTEGER as natInterfaceRealm  
  BITS as natInterfaceServiceType  
  Counter64 as natInterfaceInTranslates  
  Counter64 as natInterfaceOutTranslates  
  Counter64 as natInterfaceDiscards  
  StorageType as natInterfaceStorageType  
  RowStatus as natInterfaceRowStatus  

NatAddrMapEntry  
SEQUENCE    
  NatAddrMapId as natAddrMapIndex  
  SnmpAdminString as natAddrMapName  
  NatAssociationType as natAddrMapEntryType  
  NatTranslationEntity as natAddrMapTranslationEntity  
  InetAddressType as natAddrMapLocalAddrType  
  InetAddress as natAddrMapLocalAddrFrom  
  InetAddress as natAddrMapLocalAddrTo  
  InetPortNumber as natAddrMapLocalPortFrom  
  InetPortNumber as natAddrMapLocalPortTo  
  InetAddressType as natAddrMapGlobalAddrType  
  InetAddress as natAddrMapGlobalAddrFrom  
  InetAddress as natAddrMapGlobalAddrTo  
  InetPortNumber as natAddrMapGlobalPortFrom  
  InetPortNumber as natAddrMapGlobalPortTo  
  NatProtocolMap as natAddrMapProtocol  
  Counter64 as natAddrMapInTranslates  
  Counter64 as natAddrMapOutTranslates  
  Counter64 as natAddrMapDiscards  
  Gauge32 as natAddrMapAddrUsed  
  StorageType as natAddrMapStorageType  
  RowStatus as natAddrMapRowStatus  

NatAddrBindEntry  
SEQUENCE    
  InetAddressType as natAddrBindLocalAddrType  
  InetAddress as natAddrBindLocalAddr  
  InetAddressType as natAddrBindGlobalAddrType  
  InetAddress as natAddrBindGlobalAddr  
  NatBindId as natAddrBindId  
  NatTranslationEntity as natAddrBindTranslationEntity  
  NatAssociationType as natAddrBindType  
  NatAddrMapId as natAddrBindMapIndex  
  Gauge32 as natAddrBindSessions  
  TimeTicks as natAddrBindMaxIdleTime  
  TimeTicks as natAddrBindCurrentIdleTime  
  Counter64 as natAddrBindInTranslates  
  Counter64 as natAddrBindOutTranslates  

NatAddrPortBindEntry  
SEQUENCE    
  InetAddressType as natAddrPortBindLocalAddrType  
  InetAddress as natAddrPortBindLocalAddr  
  InetPortNumber as natAddrPortBindLocalPort  
  NatProtocolType as natAddrPortBindProtocol  
  InetAddressType as natAddrPortBindGlobalAddrType  
  InetAddress as natAddrPortBindGlobalAddr  
  InetPortNumber as natAddrPortBindGlobalPort  
  NatBindId as natAddrPortBindId  
  NatTranslationEntity as natAddrPortBindTranslationEntity  
  NatAssociationType as natAddrPortBindType  
  NatAddrMapId as natAddrPortBindMapIndex  
  Gauge32 as natAddrPortBindSessions  
  TimeTicks as natAddrPortBindMaxIdleTime  
  TimeTicks as natAddrPortBindCurrentIdleTime  
  Counter64 as natAddrPortBindInTranslates  
  Counter64 as natAddrPortBindOutTranslates  

NatSessionEntry  
SEQUENCE    
  NatSessionId as natSessionIndex  
  NatBindIdOrZero as natSessionPrivateSrcEPBindId  
  NatBindMode as natSessionPrivateSrcEPBindMode  
  NatBindIdOrZero as natSessionPrivateDstEPBindId  
  NatBindMode as natSessionPrivateDstEPBindMode  
  INTEGER as natSessionDirection  
  TimeTicks as natSessionUpTime  
  NatAddrMapId as natSessionAddrMapIndex  
  NatProtocolType as natSessionProtocolType  
  InetAddressType as natSessionPrivateAddrType  
  InetAddress as natSessionPrivateSrcAddr  
  InetPortNumber as natSessionPrivateSrcPort  
  InetAddress as natSessionPrivateDstAddr  
  InetPortNumber as natSessionPrivateDstPort  
  InetAddressType as natSessionPublicAddrType  
  InetAddress as natSessionPublicSrcAddr  
  InetPortNumber as natSessionPublicSrcPort  
  InetAddress as natSessionPublicDstAddr  
  InetPortNumber as natSessionPublicDstPort  
  TimeTicks as natSessionMaxIdleTime  
  TimeTicks as natSessionCurrentIdleTime  
  Counter64 as natSessionInTranslates  
  Counter64 as natSessionOutTranslates  

NatProtocolEntry  
SEQUENCE    
  NatProtocolType as natProtocol  
  Counter64 as natProtocolInTranslates  
  Counter64 as natProtocolOutTranslates  
  Counter64 as natProtocolDiscards