
| RFC1155-SMI | RFC-1212 | RFC1213-MIB |
| SNMPv2-TC-v1 |
| enterprises | Counter | IpAddress |
| Opaque | OBJECT-TYPE | DisplayString |
| ifIndex | DateAndTime | TruthValue |
| nec | 1.3.6.1.4.1.119 | ||
| OBJECT IDENTIFIER | |||
| necProduct | 1.3.6.1.4.1.119.1 | ||
| OBJECT IDENTIFIER | |||
| atomis | 1.3.6.1.4.1.119.1.14 | ||
| OBJECT IDENTIFIER | |||
| m7-phase2 | 1.3.6.1.4.1.119.1.14.9 | ||
| OBJECT IDENTIFIER | |||
| m7-corporate | 1.3.6.1.4.1.119.1.14.12 | ||
| OBJECT IDENTIFIER | |||
| nec-mib | 1.3.6.1.4.1.119.2 | ||
| OBJECT IDENTIFIER | |||
| necProductDepend | 1.3.6.1.4.1.119.2.3 | ||
| OBJECT IDENTIFIER | |||
| atomis-mib | 1.3.6.1.4.1.119.2.3.14 | ||
| OBJECT IDENTIFIER | |||
| m7-phase2-mib | 1.3.6.1.4.1.119.2.3.14.9 | ||
| OBJECT IDENTIFIER | |||
| node | 1.3.6.1.4.1.119.2.3.14.9.1 | ||
| OBJECT IDENTIFIER | |||
| nodeStatus | 1.3.6.1.4.1.119.2.3.14.9.1.1 | ||
| OBJECT IDENTIFIER | |||
| nodeStatusOperStatus | 1.3.6.1.4.1.119.2.3.14.9.1.1.1 | ||
| Indicate operational status of the equipment. | |||
| OBJECT-TYPE | |||
| INTEGER | down(1), active(2), installing(3) | ||
| nodeStatusStartTime | 1.3.6.1.4.1.119.2.3.14.9.1.1.2 | ||
| Date and Time when the equipment was last restarted | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| nodeStatusNodeId | 1.3.6.1.4.1.119.2.3.14.9.1.1.3 | ||
| Node ID of the equipment | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| nodeStatusSelfSystem | 1.3.6.1.4.1.119.2.3.14.9.1.1.4 | ||
| Indicate which system of the SW-Engine the NMS is connected with. | |||
| OBJECT-TYPE | |||
| INTEGER | system-0(1), system-1(2) | ||
| nodeStatusSwitchType | 1.3.6.1.4.1.119.2.3.14.9.1.1.5 | ||
| Indicate the type of SW-Engine. | |||
| OBJECT-TYPE | |||
| INTEGER | sw-Engine-5G(1), sw-Engine-10G(2) | ||
| nodeStatusFan | 1.3.6.1.4.1.119.2.3.14.9.1.1.6 | ||
| Indicate operational status of the FAN of the equipment. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), failure(2) | ||
| nodeStatusEnvironment | 1.3.6.1.4.1.119.2.3.14.9.1.1.7 | ||
| Peripheral temperature environment of the equipment. If the peripheral temperature exceeds 50 C, this object enters noGood(2). | |||
| OBJECT-TYPE | |||
| INTEGER | good(1), noGood(2) | ||
| nodeStatusTable | 1.3.6.1.4.1.119.2.3.14.9.1.2 | ||
| Table which indicates the status of each part of the equipment. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| NodeStatusEntry | |||
| nodeStatusEntry | 1.3.6.1.4.1.119.2.3.14.9.1.2.1 | ||
| Entry of the configuration of the table. | |||
| OBJECT-TYPE | |||
| NodeStatusEntry | |||
| nodeStatusIndex | 1.3.6.1.4.1.119.2.3.14.9.1.2.1.1 | ||
| Index of the system configuration of the equipment | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| nodeStatusPower | 1.3.6.1.4.1.119.2.3.14.9.1.2.1.2 | ||
| Indicate the status of the Power Unit of the equipment. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), failure(2), notInstalled(99) | ||
| nodeStatusSwitchMode | 1.3.6.1.4.1.119.2.3.14.9.1.2.1.3 | ||
| Indicate operational mode of SW-Engine of the equipment. | |||
| OBJECT-TYPE | |||
| INTEGER | act(1), sby(2), notInstalled(99) | ||
| nodeStatusSwitch | 1.3.6.1.4.1.119.2.3.14.9.1.2.1.4 | ||
| Indicate the status of the SW-Engine of the equipment. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), failure(2), diagnostics(3), diagnosis-status-NG(4), initializing(5), notInstalled(99) | ||
| nodePCMCIATable | 1.3.6.1.4.1.119.2.3.14.9.1.3 | ||
| Table which indicates the status of the PCMCIA card. Every PCMCIA slot is provided with an entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| NodePCMCIAEntry | |||
| nodePCMCIAEntry | 1.3.6.1.4.1.119.2.3.14.9.1.3.1 | ||
| Entry of nodePCMCIATable | |||
| OBJECT-TYPE | |||
| NodePCMCIAEntry | |||
| nodePCMCIAIndex | 1.3.6.1.4.1.119.2.3.14.9.1.3.1.1 | ||
| PCMCIA slot number per SW-Engine | |||
| OBJECT-TYPE | |||
| INTEGER | 1..2 | ||
| nodePCMCIAStatus | 1.3.6.1.4.1.119.2.3.14.9.1.3.1.2 | ||
| Status of PCMCIA card | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), failure(2), initializing(3), busy(4), unknown(5), notInstalled(99) | ||
| nodePCMCIAType | 1.3.6.1.4.1.119.2.3.14.9.1.3.1.3 | ||
| Type of installed PCMCIA card | |||
| OBJECT-TYPE | |||
| INTEGER | lan-card(1), ata-card(2), unknown(3), notInstalled(99) | ||
| nodeOpe | 1.3.6.1.4.1.119.2.3.14.9.1.4 | ||
| OBJECT IDENTIFIER | |||
| nodeOpeSave | 1.3.6.1.4.1.119.2.3.14.9.1.4.1 | ||
| Save processing. Save System Configuration information in FROM. The result is indicated in nodeOpeSaveResult. The value at read is always noOperation (1). | |||
| OBJECT-TYPE | |||
| INTEGER | noOperation(1), save(2) | ||
| nodeOpeSaveResult | 1.3.6.1.4.1.119.2.3.14.9.1.4.2 | ||
| The result of SAVE processing OK/NG indicate that SAVE processing completed/failed, respectively. (NearEND) indicates that the number of write counts approaches to the limit. | |||
| OBJECT-TYPE | |||
| INTEGER | succeed(1), succeed-0(2), succeed-1(3), temporaryFailure(4), nearend(5), nearend-0(6), nearend-0-failure-1(7), nearend-1(8), nearend-1-failure-0(9), notReady(10), ready(11) | ||
| nodeOpeCopy | 1.3.6.1.4.1.119.2.3.14.9.1.4.3 | ||
| Copy the system configuration information/LM to the FROM of other system. The result is indicated in nodeOpeCopyResult. The value at read is always noOperation(1). | |||
| OBJECT-TYPE | |||
| INTEGER | noOperation(1), copy-all-from-act(2), copy-all-from-sby(3), copy-config-from-act(4), copy-config-from-sby(5), copy-system-from-act(6), copy-system-from-sby(7) | ||
| nodeOpeCopyResult | 1.3.6.1.4.1.119.2.3.14.9.1.4.4 | ||
| Result of the copy processing. | |||
| OBJECT-TYPE | |||
| INTEGER | succeed(1), temporaryFailure(2), nearend(3), notReady(4), ready(5) | ||
| nodeOpeReset | 1.3.6.1.4.1.119.2.3.14.9.1.4.5 | ||
| System Reset processing The value at read is always noOperation(1). | |||
| OBJECT-TYPE | |||
| INTEGER | noOperation(1), reset-act(2), reset-sby(3), ach(4) | ||
| slot | 1.3.6.1.4.1.119.2.3.14.9.2 | ||
| OBJECT IDENTIFIER | |||
| slotIfConfTable | 1.3.6.1.4.1.119.2.3.14.9.2.1 | ||
| Table which indicates the line card configuration of the equipment | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SlotIfConfEntry | |||
| slotIfConfEntry | 1.3.6.1.4.1.119.2.3.14.9.2.1.1 | ||
| Entry of the line card configuration | |||
| OBJECT-TYPE | |||
| SlotIfConfEntry | |||
| slotIfConfIndex | 1.3.6.1.4.1.119.2.3.14.9.2.1.1.1 | ||
| Index of line card configuration | |||
| OBJECT-TYPE | |||
| INTEGER | 1..16 | ||
| slotIfConfPhysType | 1.3.6.1.4.1.119.2.3.14.9.2.1.1.2 | ||
| PMD layer/physical layer format of the line card. Above stated [oc3c], [oc12c] are ATM Form conformed names. They are corresponding to the ITU-T conformed names as follows: oc3c - STM1 oc12 - STM4 sts3c - STM1 | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), taxi-100M(2), oc3c-SMF-Long(3), oc3c-SMF-Short(4), oc3c-MMF(5), relay-6Mcel(6), j2-6M-4M-3M(7), utp-5(8), oc12c-SMF-Type-A(9), oc12c-SMF-Type-B(10), ds3(11), e3(12), bts-1(13), bts-4(14), primary-1536K-1152K-768K-512K-384K-256K-192K(15), ds1(16), e1(17), oc3c-POF(18), sts3c-COAXIAL(19), vod-RxHFC4M(50), vod-TxHFC27M(51), svr(52), fr-ds1(53), fr-e1(54), dcs(55), ce-ds3(56), ce-ds1(57), ce-e1(58), ce-J2(59), svr2(60), notInstalled(99) | ||
| slotIfConfRev | 1.3.6.1.4.1.119.2.3.14.9.2.1.1.3 | ||
| The revision of the line cards. JpnToEng[パッケージ未実装時は,0 length.] | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| slotIfConfStatus | 1.3.6.1.4.1.119.2.3.14.9.2.1.1.4 | ||
| Operational status of the line cards. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), inService(2), outOfService(3), testing(4), initializing(5), installing(6), notInstalled(99) | ||
| slotIfConfBufferType | 1.3.6.1.4.1.119.2.3.14.9.2.1.1.5 | ||
| The Buffer ID of the line cards. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), ph1-buffer(2), ph2-buffer(3), fr-buffer(4), fr-buffer2(5), notInstalled(99) | ||
| slotIfConfBufferRev | 1.3.6.1.4.1.119.2.3.14.9.2.1.1.6 | ||
| The revision of the line card's buffers. JpnToEng[パッケージ未実装時は,0 length.] | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| slotIfConfReset | 1.3.6.1.4.1.119.2.3.14.9.2.1.1.7 | ||
| Line card reset. The result of the reset order is indicated in slotIfConfResetResult. JpnToEng[PKG未実装時以外の読み込み時の値は,いつも noOperation(1)である.] | |||
| OBJECT-TYPE | |||
| INTEGER | noOperation(1), reset(2), notInstalled(99) | ||
| slotIfConfResetResult | 1.3.6.1.4.1.119.2.3.14.9.2.1.1.8 | ||
| The current result of the reset order by slotIfConfReset. | |||
| OBJECT-TYPE | |||
| INTEGER | succeed(1), other(2), diagnostics(3), unchangeableSlaveLine(4), notInstalled(99) | ||
| linf | 1.3.6.1.4.1.119.2.3.14.9.3 | ||
| OBJECT IDENTIFIER | |||
| linfStatusTable | 1.3.6.1.4.1.119.2.3.14.9.3.1 | ||
| Table related to the ATM specific lines which could not be defined by MIB-II. The table includes the configuration information, operational status and error types of lines. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LinfStatusEntry | |||
| linfStatusEntry | 1.3.6.1.4.1.119.2.3.14.9.3.1.1 | ||
| Entry of the line interface status indication. | |||
| OBJECT-TYPE | |||
| LinfStatusEntry | |||
| linfIndex | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.1 | ||
| Index of the line interface status indication | |||
| OBJECT-TYPE | |||
| INTEGER | 1..64 | ||
| linfStatus | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.2 | ||
| Status of the line interface or the receive clock | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), los(2), lof(3), loc(4), ais-path(5), ais-section(6), yellow-section(7), yellow-path(8), lop(9), ais(10), payload-all-one(11), rai(12), oof(13), idle(14), rdi(15), plcp-oof(16), plcp-lof(17), plcp-yellow(18), red(19), loss-of-64K-clock(80), loss-of-8K-clock(81), frequency-out-of-range(82), failure(97), administratively-down(98), notInstalled(99) | ||
| linfLoopBack | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.3 | ||
| Loop back status | |||
| OBJECT-TYPE | |||
| INTEGER | others(1), normal(2), localLoopBack(3), remoteLoopBack(4), notInstalled(99) | ||
| linfConf | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.4 | ||
| Line card type. | |||
| OBJECT-TYPE | |||
| INTEGER | others(1), private-UNI(2), private-NNI(3), public-UNI(4), uni(6), nni(7), notInstalled(99) | ||
| linfFwdAvailableBandWidth | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.5 | ||
| Forward Available BandWidth(Mbps). JpnToEng[PKG未実装時は,0] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| linfBkwdAvailableBandWidth | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.6 | ||
| Backward Available BandWidth(Mbps). JpnToEng[PKG未実装時は,0] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| linfJ2Rate | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.7 | ||
| Indicate the line rate of the J2-dedicated line service. | |||
| OBJECT-TYPE | |||
| INTEGER | not-leased-line(1), type-3-Mbps(2), type-4point5-Mbps(3), type-6point3-Mbps(4), notInstalled(99) | ||
| linfCacFactor | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.8 | ||
| JpnToEng(次行から7行分) | |||
| OBJECT-TYPE | |||
| INTEGER | 0 | 10..1000 | ||
| linfLoopBackCause | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.9 | ||
| JpnToEng[物理ループバックの設定結果.] | |||
| OBJECT-TYPE | |||
| INTEGER | succeed(1), diagnosis(2), failure(3), notSupportedByPkg(4), alreadyRegistered(5), adminDown(6), initializing(7), notInstalled(99) | ||
| linfBandWidth | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.10 | ||
| BandWidth[cell/s].JpnToEng[無効またはPKG未実装時は値 0.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| linfRecommendation | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.11 | ||
| JpnToEng[対応勧告] | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), atmForum(2), itu(3), ttc(4), frameRelayForum(5), itu-t(6), ansi(7), fourVendor(8), notInstalled(99) | ||
| linfUnassignedIdle | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.12 | ||
| Unassigned/Idle | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), unAssigned(2), idle(3), notInstalled(99) | ||
| linfMaxActiveVpiBits | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.13 | ||
| The length of valid VPI bits.JpnToEng[PKG未実装時は0.] | |||
| OBJECT-TYPE | |||
| INTEGER | 0..12 | ||
| linfMaxActiveVciBits | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.14 | ||
| The length of valid VCI bits.JpnToEng[PKG未実装時は0.] | |||
| OBJECT-TYPE | |||
| INTEGER | 0..14 | ||
| linfPhysType | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.15 | ||
| JpnToEng[この回線が属するスロットの slotIfConfPhysType 値] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| linfParam1 | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.16 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| linfParam2 | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.17 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| linfParam3 | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.18 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| linfParam4 | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.19 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| linfParam5 | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.20 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| linfParam6 | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.21 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| linfParam7 | 1.3.6.1.4.1.119.2.3.14.9.3.1.1.22 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| linfFifoConfTable | 1.3.6.1.4.1.119.2.3.14.9.3.2 | ||
| Indicate status of FIFO on the shaper-line card. * JpnToEng[SCR, MBSを省略したときはCBRとみなし, PCRだけを元にシェーピングレートの設定を行なう.] * Relationship between PCR, SCR and MBS value. PCR >= SCR PCR >= MBS | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LinfFifoConfEntry | |||
| linfFifoConfEntry | 1.3.6.1.4.1.119.2.3.14.9.3.2.1 | ||
| Entry of FIFO status indication | |||
| OBJECT-TYPE | |||
| LinfFifoConfEntry | |||
| linfFifoConfifIndex | 1.3.6.1.4.1.119.2.3.14.9.3.2.1.1 | ||
| Line Interface Index | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| linfFifoConfIndex | 1.3.6.1.4.1.119.2.3.14.9.3.2.1.2 | ||
| Index of FIFO | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| linfFifoConfStatus | 1.3.6.1.4.1.119.2.3.14.9.3.2.1.3 | ||
| Status of FIFO | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), overflow(2) | ||
| linfFifoConfPeekRate | 1.3.6.1.4.1.119.2.3.14.9.3.2.1.4 | ||
| Peak Cell rate (PCR) for shaper-line card. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..1412830 | ||
| linfFifoConfSustainRate | 1.3.6.1.4.1.119.2.3.14.9.3.2.1.5 | ||
| Sustainable Cell Rate ( SCR) for shaper-line card. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..1412830 | ||
| linfFifoConfMaxBurstSize | 1.3.6.1.4.1.119.2.3.14.9.3.2.1.6 | ||
| Maximum Burst Size (MBS) for the shaper-line card. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..1412830 | ||
| linfFifoConfRowStatus | 1.3.6.1.4.1.119.2.3.14.9.3.2.1.7 | ||
| This object is used to designate the setting method for the shaping rate from the manager. Also, this object returns the reply to the shaping rate setting request from the agent side. - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device; - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row but not to have it available for use by the managed device; and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6) | ||
| conn | 1.3.6.1.4.1.119.2.3.14.9.4 | ||
| OBJECT IDENTIFIER | |||
| connPvc | 1.3.6.1.4.1.119.2.3.14.9.4.1 | ||
| OBJECT IDENTIFIER | |||
| connPvcOpe | 1.3.6.1.4.1.119.2.3.14.9.4.1.1 | ||
| OBJECT IDENTIFIER | |||
| connPvcOpeLowPort | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.1 | ||
| Low-side line port number. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65 | -1 | ||
| connPvcOpeLowVpi | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.2 | ||
| Low-side VPI number. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..16383 | -1 | ||
| connPvcOpeLowVci | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.3 | ||
| Low-side VCI number. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..16383 | -1 | ||
| connPvcOpeHighPort | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.4 | ||
| High-side line port number. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65 | -1 | ||
| connPvcOpeHighVpi | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.5 | ||
| High-side VPI number. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..16383 | -1 | ||
| connPvcOpeHighVci | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.6 | ||
| High-side VCI number. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..16383 | -1 | ||
| connPvcOpeTopology | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.7 | ||
| Topology of the Connection. | |||
| OBJECT-TYPE | |||
| INTEGER | uni-directional-VCC(1), bi-directional-VCC(2), uni-directional-VPC(3), bi-directional-VPC(4), broadcast-VPC(5), broadcast-VCC(6) | ||
| connPvcOpeTrafficType | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.8 | ||
| Traffic Type. | |||
| OBJECT-TYPE | |||
| INTEGER | traffic-CBR(1), traffic-rt-VBR(2), traffic-nrt-VBR(3), traffic-ABR(4), traffic-UBR(5) | ||
| connPvcOpeStatus | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.9 | ||
| JpnToEng[PVC設定/削除の制御を行なう.] | |||
| OBJECT-TYPE | |||
| INTEGER | allocate(1), establish(2), add(3), delete(4), remove(5), free(6) | ||
| connPvcOpeCause | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.10 | ||
| The result of the connection operation. | |||
| OBJECT-TYPE | |||
| INTEGER | rowExisting(1), allocateSucceed(2), vpivciLowBusy(3), vpivciHighBusy(4), vpivciOutOfRange(5), rateLowOverFlow(6), rateHighOverFlow(7), broadcastTableFull(8), inconsistentVPVC(9), lineDiagnosis(10), missMatchTrfType(11), illegalLowFileName(12), illegalHighFileName(13), illegalLowShaper(14), illegalHighShaper(15), illegalOperation(16), parameterIsNotEnough(17), diagnostics(18), otherFailure(19), illegalLowRateForUPC(20), illegalHighRateForUPC(21), noSpecifiedConnection(22), noCevc(23), noDlci(24), illegalTopology(25), noLowShaperForGateway(26), noHighShaperForGateway(27), noPvcLowShaperForGateway(28), noPvcHighShaperForGateway(29), missMatchTrfTypeLowShaperForGateway(30), missMatchTrfTypeHighShaperForGateway(31), leafSetAnotherLine(32), insusfficientPCRofProfile(33) | ||
| connPvcOpeLowFifoIndex | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.11 | ||
| Shaper number of Forward. If shaping is not performed, designate 0. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..16 | ||
| connPvcOpeHighFifoIndex | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.12 | ||
| Shaper number of Backward. If shaping is not performed, designate 0. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..16 | ||
| connPvcOpeLowParam1 | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.13 | ||
| UPC mode of Forward. | |||
| OBJECT-TYPE | |||
| INTEGER | off(1), mode1(2), mode2(3), mode3(4), mode4(5), mode5(6) | ||
| connPvcOpeHighParam1 | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.14 | ||
| UPC mode of Backward. | |||
| OBJECT-TYPE | |||
| INTEGER | off(1), mode1(2), mode2(3), mode3(4), mode4(5), mode5(6) | ||
| connPvcOpeLowParam2 | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.15 | ||
| Profile name of Forward. If nothing is designated, the string of size(0) is designated. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..10 | 0) | ||
| connPvcOpeHighParam2 | 1.3.6.1.4.1.119.2.3.14.9.4.1.1.16 | ||
| Profile name of Backward. If nothing is designated, the string of size(0) is designated. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..10 | 0) | ||
| connPvcTable | 1.3.6.1.4.1.119.2.3.14.9.4.1.2 | ||
| JpnToEng(次の4行分を) | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ConnPvcEntry | |||
| connPvcEntry | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1 | ||
| Entry of connPvcTable. e.g. receive +----------------------------------+transmit =======>| ---- uni-directional-VCC ---- |=======> (1/0/32)| |(2/0/32) =======>| ---- bi-directional-VCC ---- |=======> (1/0/33)| |(2/0/33) =======>| ---- broadcast - VCC ---+---- |=======> (1/0/34)| | |(2/0/34) | +---- |=======> | |(3/0/34) +----------------------------------+ (line/vpi/vci) connPvcContrastPort.1.0.32.1.1=2 connPvcContrastPort.2.0.32.2.1=1 connPvcContrastPort.1.0.33.3.1=2 connPvcContrastPort.2.0.33.3.1=1 connPvcContrastPort.1.0.34.5.1=2 connPvcContrastPort.1.0.34.5.2=3 connPvcContrastPort.2.0.34.4.1=1 connPvcContrastPort.3.0.34.4.1=1 | |||
| OBJECT-TYPE | |||
| ConnPvcEntry | |||
| connPvcPort | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.1 | ||
| Line port number | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connPvcVpi | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.2 | ||
| VPI number | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connPvcVci | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.3 | ||
| VCI number | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connPvcDirection | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.4 | ||
| Indicate cell flow. | |||
| OBJECT-TYPE | |||
| INTEGER | in(1), out(2), in-out(3), multi-out(4), multi-in(5) | ||
| connPvcIndex | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.5 | ||
| JpnToEng[スイッチングするエンドポイントを 識別するインデックス.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connPvcContrastPort | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.6 | ||
| JpnToEng[スイッチングするエンドポイントの回線番号.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connPvcContrastVpi | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.7 | ||
| JpnToEng[スイッチングするエンドポイントのVPI番号.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connPvcContrastVci | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.8 | ||
| JpnToEng[スイッチングするエンドポイントのVCI番号.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connPvcTopology | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.9 | ||
| Topology of the Connection. | |||
| OBJECT-TYPE | |||
| INTEGER | uni-directional-VCC(1), bi-directional-VCC(2), uni-directional-VPC(3), bi-directional-VPC(4), broadcast-VPC(5), broadcast-VCC(6), gateway(7) | ||
| connPvcTrafficType | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.10 | ||
| Traffic Type. | |||
| OBJECT-TYPE | |||
| INTEGER | traffic-CBR(1), traffic-rt-VBR(2), traffic-nrt-VBR(3), traffic-ABR(4), traffic-UBR(5) | ||
| connPvcFifoIndex | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.11 | ||
| The Shaper numbers of the direction from this endpoint to the endpoint to be switched. Value 0 means that Shaping will not be performed. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..16 | ||
| connPvcContrastFifoIndex | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.12 | ||
| The Shaper number of the direction from the endpoint to be switched to this end point. Value 0 means that Shaping will not be performed. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..16 | ||
| connPvcTrfConf | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.13 | ||
| Indicate Traffic control/status. If a path does not exist, noSuchName. 1. Indicate Traffic status 1) entry...registered 2) remove...not registered(initial status) 2. Register Traffic 1) Set connPvcTrfConf to 'entry', to perform the registration process. 2) Then, get connPvcTrfResult. For normal end, it contains entrySucceed, for abnormal end, it contains other value. 3. Delete Traffic 1) Set connPvcTrfConf to 'remove', to perform the deletion process. 2) Then, get connPvTrfResult. For normal end, it contains entrySucceed, for abnormal end, it contains other value. | |||
| OBJECT-TYPE | |||
| INTEGER | entry(1), remove(2) | ||
| connPvcTrfResult | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.14 | ||
| Indicate the processing result after Traffic control. If the path does not exist, noSuchName. The result of the registration EntrySucceed (2) --- Normal end of the registration AlreadyEntry (3) --- Double registration tableOverflow (4) --- The number of registration is over the limit. The result of the deletion RemoveSucceed (5) --- Normal end of the deletion notEntry (6) --- Non-registration Normally, other (1) is indicated. It is the current status just after the traffic control. Once, the traffic control is got, then it returns to other (1). | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), entrySucceed(2), alreadyEntry(3), tableOverflow(4), removeSucceed(5), notEntry(6) | ||
| connPvcParam1 | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.15 | ||
| UPC mode of the direction from this endpoint to the endpoint to be switched. If nothing is designated, or the designation is invalid, off (1) is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | off(1), mode1(2), mode2(3), mode3(4), mode4(5), mode5(6) | ||
| connPvcContrastParam1 | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.16 | ||
| UPC mode of the direction from the endpoint to be switched to this end point. If nothing is designated, or the designation is invalid, off (1) is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | off(1), mode1(2), mode2(3), mode3(4), mode4(5), mode5(6) | ||
| connPvcParam2 | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.17 | ||
| Profile name of the direction from this endpoint to the endpoint to be switched. If nothing is designated, or the designation is invalid, the string of size(0) is indicated. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..10 | 0) | ||
| connPvcContrastParam2 | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.18 | ||
| Profile name of the direction from the endpoint to be switched to this end point. If nothing is designated, or the designation is invalid, the string of size(0) is indicated. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..10 | 0) | ||
| connPvcParam3 | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.19 | ||
| PCR[cell/s] of the direction from this endpoint to the endpoint to be switched. If the value is invalid, -1 is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connPvcContrastParam3 | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.20 | ||
| PCR[cell/s] of the direction from the endpoint to be switched to this end point. If the value is invalid, -1 is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connPvcParam4 | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.21 | ||
| SCR[cell/s] of the direction from this endpoint to the endpoint to be switched. If the value is invalid, -1 is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connPvcContrastParam4 | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.22 | ||
| SCR[cell/s] of the direction from the endpoint to be switched to this end point. If the value is invalid, -1 is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connPvcParam5 | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.23 | ||
| MBS[cell] of the direction from this endpoint to the endpoint to be switched. If the value is invalid, -1 is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connPvcContrastParam5 | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.24 | ||
| MBS[cell] of the direction from the endpoint to be switched to this end point. If the value is invalid, -1 is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connPvcParam6 | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.25 | ||
| EPD(Early Packet Discard) of the direction from this endpoint to the endpoint to be switched. Indicate if the discard processing in the unit of AAL5 packet should be performed or not when the threshold is exceeded. If the value is invalid, off(1) is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | off(1), on(2) | ||
| connPvcContrastParam6 | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.26 | ||
| EPD(Early Packet Discard) of the direction from the endpoint to be switched to this end point. Indicate if the discard processing in the unit of AAL5 packet should be performed or not when the threshold is exceeded. If the value is invalid, off(1) is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | off(1), on(2) | ||
| connPvcParam7 | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.27 | ||
| MCR[cell/s]. Not supported here. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connPvcContrastParam7 | 1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.28 | ||
| MCR[cell/s]. Not supported here. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connPvcTrfTable | 1.3.6.1.4.1.119.2.3.14.9.4.1.3 | ||
| Indicate traffic counter information per connection. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ConnPvcTrfEntry | |||
| connPvcTrfEntry | 1.3.6.1.4.1.119.2.3.14.9.4.1.3.1 | ||
| Entry of traffic per connection. Every INDEX is equivalent to the one defined in connPvcEntry. | |||
| OBJECT-TYPE | |||
| ConnPvcTrfEntry | |||
| connPvcTrfInCells | 1.3.6.1.4.1.119.2.3.14.9.4.1.3.1.1 | ||
| The number of receive cells 64 bit counter | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| connPvcTrfInCellsCounters | 1.3.6.1.4.1.119.2.3.14.9.4.1.3.1.2 | ||
| The number of receive cells 32 bit counter | |||
| OBJECT-TYPE | |||
| Counter | |||
| connPvcTrfOutCells | 1.3.6.1.4.1.119.2.3.14.9.4.1.3.1.3 | ||
| The number of transmit cells 64 bit counter | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| connPvcTrfOutCellsCounters | 1.3.6.1.4.1.119.2.3.14.9.4.1.3.1.4 | ||
| The number of transmit cells 32 bit counter | |||
| OBJECT-TYPE | |||
| Counter | |||
| connPvcTrfInDropCells | 1.3.6.1.4.1.119.2.3.14.9.4.1.3.1.5 | ||
| The number of receive drop cells 64 bit counter | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| connPvcTrfInDropCellsCounters | 1.3.6.1.4.1.119.2.3.14.9.4.1.3.1.6 | ||
| The number of receive drop cells 32 bit counter | |||
| OBJECT-TYPE | |||
| Counter | |||
| connConf | 1.3.6.1.4.1.119.2.3.14.9.4.2 | ||
| OBJECT IDENTIFIER | |||
| connConfNode | 1.3.6.1.4.1.119.2.3.14.9.4.2.1 | ||
| OBJECT IDENTIFIER | |||
| connConfNodePvcs | 1.3.6.1.4.1.119.2.3.14.9.4.2.1.1 | ||
| The number of current established PVCs in this switch. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..32000 | ||
| connConfNodeSvcs | 1.3.6.1.4.1.119.2.3.14.9.4.2.1.2 | ||
| The number of current established SVCs in this switch. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..4096 | ||
| connConfNodeSoftPvcs | 1.3.6.1.4.1.119.2.3.14.9.4.2.1.3 | ||
| The number of current established Soft PVPCs/PVCCs in this switch. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..4096 | ||
| connConfNodeTrafClear | 1.3.6.1.4.1.119.2.3.14.9.4.2.1.4 | ||
| Set allClear (1) to clear all traffic registration information. If noOperation (2) is written, nothing will be performed. The value at read is always noOperation (2). | |||
| OBJECT-TYPE | |||
| INTEGER | allClear(1), noOperation(2) | ||
| connConfNodeTrafs | 1.3.6.1.4.1.119.2.3.14.9.4.2.1.5 | ||
| The number of traffic registrations which are being set in the switch. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..1024 | ||
| connConfNodeCompleteSvcs | 1.3.6.1.4.1.119.2.3.14.9.4.2.1.6 | ||
| The number of SVC complete calls | |||
| OBJECT-TYPE | |||
| Counter | |||
| connConfNodeUnCompleteSvcs | 1.3.6.1.4.1.119.2.3.14.9.4.2.1.7 | ||
| The number of SVC incomplete calls | |||
| OBJECT-TYPE | |||
| Counter | |||
| connConfIfTable | 1.3.6.1.4.1.119.2.3.14.9.4.2.2 | ||
| The table is used to show the information of current established connections on the interface. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ConnConfIfEntry | |||
| connConfIfEntry | 1.3.6.1.4.1.119.2.3.14.9.4.2.2.1 | ||
| Entry of connConfIfTable. | |||
| OBJECT-TYPE | |||
| ConnConfIfEntry | |||
| connConfIfPvcs | 1.3.6.1.4.1.119.2.3.14.9.4.2.2.1.1 | ||
| The number of current established PVCs on the interface. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..16384 | ||
| connConfIfSvcs | 1.3.6.1.4.1.119.2.3.14.9.4.2.2.1.2 | ||
| The number of current established SVCs on the interface. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..4096 | ||
| connConfIfSoftPvcs | 1.3.6.1.4.1.119.2.3.14.9.4.2.2.1.3 | ||
| The number of current established Soft PVPCs/PVCCs on the interface. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..4096 | ||
| connRoute | 1.3.6.1.4.1.119.2.3.14.9.4.3 | ||
| OBJECT IDENTIFIER | |||
| connRouteOpe | 1.3.6.1.4.1.119.2.3.14.9.4.3.1 | ||
| OBJECT IDENTIFIER | |||
| connRouteOpeStatus | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.1 | ||
| allocate : allocate the right to operate the routing information to a manager. add : add the routing information to static routing table. delete : delete the routing information from static routing table. free : free the right to operate the routing information from a manager. +-------------+ | | +---+----+<---+ ----------->|free|<----------------- | +----+ | | | | +--------+ +----------+ | ---->|allocate| -----> |add/delete|- +--------+ +----------+ | |||
| OBJECT-TYPE | |||
| INTEGER | allocate(1), add(2), delete(3), free(4) | ||
| connRouteOpeFailureCause | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.2 | ||
| The result of the operation. | |||
| OBJECT-TYPE | |||
| ConnRouteOpeFailureCause | |||
| connRouteOpeAddressFormat | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.3 | ||
| OBJECT-TYPE | |||
| DstAtmAddressFormat | |||
| connRouteOpeAddressLength | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.4 | ||
| OBJECT-TYPE | |||
| DstAtmAddressLength | |||
| connRouteOpeAddress | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.5 | ||
| OBJECT-TYPE | |||
| DstAtmAddress | |||
| connRouteOpePrimaryIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.6 | ||
| OBJECT-TYPE | |||
| DstPrimaryIfIndex | |||
| connRouteOpePrimaryVPI | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.7 | ||
| OBJECT-TYPE | |||
| DstPrimaryVPI | |||
| connRouteOpeSecondaryIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.8 | ||
| OBJECT-TYPE | |||
| DstSecondaryIfIndex | |||
| connRouteOpeSecondaryVPI | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.9 | ||
| OBJECT-TYPE | |||
| DstSecondaryVPI | |||
| connRouteOpeTertiaryIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.10 | ||
| OBJECT-TYPE | |||
| DstSecondaryIfIndex | |||
| connRouteOpeTertiaryVPI | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.11 | ||
| OBJECT-TYPE | |||
| DstSecondaryVPI | |||
| connRouteOpeFourthryIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.12 | ||
| OBJECT-TYPE | |||
| DstSecondaryIfIndex | |||
| connRouteOpeFourthryVPI | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.13 | ||
| OBJECT-TYPE | |||
| DstSecondaryVPI | |||
| connRouteOpeFifthryIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.14 | ||
| OBJECT-TYPE | |||
| DstSecondaryIfIndex | |||
| connRouteOpeFifthryVPI | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.15 | ||
| OBJECT-TYPE | |||
| DstSecondaryVPI | |||
| connRouteOpeSixthryIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.16 | ||
| OBJECT-TYPE | |||
| DstSecondaryIfIndex | |||
| connRouteOpeSixthryVPI | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.17 | ||
| OBJECT-TYPE | |||
| DstSecondaryVPI | |||
| connRouteOpeSeventhryIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.18 | ||
| OBJECT-TYPE | |||
| DstSecondaryIfIndex | |||
| connRouteOpeSeventhryVPI | 1.3.6.1.4.1.119.2.3.14.9.4.3.1.19 | ||
| OBJECT-TYPE | |||
| DstSecondaryVPI | |||
| connRouteTable | 1.3.6.1.4.1.119.2.3.14.9.4.3.2 | ||
| This table is used to show the static routing table for SVC. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ConnRouteEntry | |||
| connRouteEntry | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1 | ||
| Entry of connRouteTable. | |||
| OBJECT-TYPE | |||
| ConnRouteEntry | |||
| connRouteType | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.1 | ||
| The value of this object shows the routing type. | |||
| OBJECT-TYPE | |||
| INTEGER | static(1), dynamic(2) | ||
| connRoutePrimaryIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.2 | ||
| OBJECT-TYPE | |||
| DstPrimaryIfIndex | |||
| connRoutePrimaryVPI | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.3 | ||
| OBJECT-TYPE | |||
| DstPrimaryVPI | |||
| connRouteSecondaryIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.4 | ||
| OBJECT-TYPE | |||
| DstSecondaryIfIndex | |||
| connRouteSecondaryVPI | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.5 | ||
| OBJECT-TYPE | |||
| DstSecondaryVPI | |||
| connRouteTertiaryIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.6 | ||
| OBJECT-TYPE | |||
| DstSecondaryIfIndex | |||
| connRouteTertiaryVPI | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.7 | ||
| OBJECT-TYPE | |||
| DstSecondaryVPI | |||
| connRouteFourthryIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.8 | ||
| OBJECT-TYPE | |||
| DstSecondaryIfIndex | |||
| connRouteFourthryVPI | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.9 | ||
| OBJECT-TYPE | |||
| DstSecondaryVPI | |||
| connRouteFifthryIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.10 | ||
| OBJECT-TYPE | |||
| DstSecondaryIfIndex | |||
| connRouteFifthryVPI | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.11 | ||
| OBJECT-TYPE | |||
| DstSecondaryVPI | |||
| connRouteSixthryIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.12 | ||
| OBJECT-TYPE | |||
| DstSecondaryIfIndex | |||
| connRouteSixthryVPI | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.13 | ||
| OBJECT-TYPE | |||
| DstSecondaryVPI | |||
| connRouteSeventhryIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.14 | ||
| OBJECT-TYPE | |||
| DstSecondaryIfIndex | |||
| connRouteSeventhryVPI | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.15 | ||
| OBJECT-TYPE | |||
| DstSecondaryVPI | |||
| connRoutePrimaryStatus | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.16 | ||
| Operational status of the primary routing. If the primary route of the routing table of the equipment is valid, enable(2), if not valid, disable(1). | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), enable(2) | ||
| connRoutePrimaryCause | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.17 | ||
| Cause of the switching from the primary route. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(0), other(1), outOfService(2), testing(3), lineInterface-Down(4), lineInterface-Failure(5), sw-Engine-Failure(6), sw-Engine-SwapOUT(7), notInstalled(99) | ||
| connRouteAtmAddressFormat | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.18 | ||
| OBJECT-TYPE | |||
| DstAtmAddressFormat | |||
| connRouteAtmAddressLength | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.19 | ||
| OBJECT-TYPE | |||
| DstAtmAddressLength | |||
| connRouteAtmAddress | 1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.20 | ||
| OBJECT-TYPE | |||
| DstAtmAddress | |||
| connSoftPvcIndexNext | 1.3.6.1.4.1.119.2.3.14.9.4.4 | ||
| This object returns the empty index of the call management table, required to access to connSoftPvcTable. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..128 | ||
| connSoftPvcTable | 1.3.6.1.4.1.119.2.3.14.9.4.5 | ||
| This table include all entries to Soft-PVPC/PVCC currently available between the lines or the line and CPU port of the switch. Also, this table is used to set or delete Soft-PVPC/PVCC. The operable connection form between Soft-PVPC/PVCC is bi- directional point-to-point only. The procedure to set the connection is as follows: 1. Acquire connSoftPvcIndex To set the connection, read connSoftPvcIndexNext and obtain an index of the Soft-PVPC/PVCC table. The index must be managed by NMS. (The index is required to take an action to the connection.) 2. Set createAndWait Set connSoftPvcRowStatus to CreateAndWait, using the obtained connSoftPvcIndex as index. If the agent will set the parameter for the Soft-PVPC/PVCC setting to the default value and make connSoftRowStatus to notReady. However, the same manager cannot create another row while creating a row (the status of the row is notRedy or notInService). 3. Get the default value Get the default value of the object which serves as parameter for the connection setting. (The agent shall return -1 if it does not have a default value.) Default values are as follows: connSoftPvcTopology bi-directional-VCC(2) connSoftPvcTrafficType traffic-UBR(5) connSoftPvcEndpointType calling(1) connSoftPvcRetry 2 connSoftPvcSrcAtmAddressFormat nsap(2) connSoftPvcSrcAtmAddressLength None connSoftPvcSrcAtmAddress 0 length string connSoftPvcSrcIfIndex None connSoftPvcSrcVPI None connSoftPvcSrcVCI None connSoftPvcDstAtmAddressFormat nsap(2) connSoftPvcDstAtmAddressLength None connSoftPvcDstAtmAddress 0 length string connSoftPvcDstIfIndex None connSoftPvcDstVPI None connSoftPvcDstVCI None connSoftPvcSrcFifoIndex 0 connSoftPvcDstFifoIndex 0 connSoftPvcNodeKind model5(1) connSoftPvcSrcParam1 off(1) connSoftPvcDstParam1 off(1) connSoftPvcSrcParam2 0 length string connSoftPvcDstParam2 0 length string connSoftPvcSrcParam3 -1 connSoftPvcDstParam3 -1 connSoftPvcSrcParam4 -1 connSoftPvcDstParam4 -1 connSoftPvcSrcParam5 -1 connSoftPvcDstParam5 -1 connSoftPvcSrcParam6 off(2) connSoftPvcDstParam6 off(2) connSoftPvcSrcParam7 None (not installed) connSoftPvcDstParam7 None (not installed) 4. Set parameter If a parameter does not have a default value, or the default value should not be used, set the parameter to a value. If all parameters are set, the agent shall make connSoftPvcRowStatus to notInService. 5. Set active By doing so, the agent checks parameters, resources and establishes the connection. 6. Get connSoftPvcRowStatus If connSoftPvcRowStatus is active, the connection setting completed successfully, if notInService,the connection setting failed. For the cause, refer to connSoftPvcCause. (Note) When the connection setting has failed, if the connection is not released, the row will remain. 7. Get connSoftPvcRestRetry Remaining counts of retry are contained. If it is positive value, the retry is in progress. If connSoftPvcRestRetry is 0, the retry completed. The result of the connection setting should be seen, when this object is 0. -1 means that infinite retry is in progress. ***Special pattern*** (1) If connSoftPvcTopology is bi-directional-VPC, set connSoftPvcSrcVCI, connSoftPvcDstVCI to 0. The procedure to release the connection is as follows: 1. Set 'destroy' Set connSoftPvcRowStatus to 'destroy', using connSoftPvcIndex of the connection to be deleted as index. The agent will delete the connection, referring to it. (Note) 'destroy' can also be set during the bypass processing. 2. Get the result If the connection is deleted, 'get' of connSoftPvcTable of the designated index becomes NoSuchName. The bypass processing of connection 1. Set notInService When the agent executes the bypass processing of connection, set connSoftPvcRowStatus to notInService, and then establish the connection. 2. Get connSoftPvcRowStatus If connSoftPvcRowStatus is 'active', the bypass connection setting has completed successfully. If connSoftPvcRowStatus remains 'notInService', the connection setting has failed. Others 1. The cut and recovery processing of connection is performed, following the delete and set procedures of the concerned connection. Each procedure is as stated before. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ConnSoftPvcEntry | |||
| connSoftPvcEntry | 1.3.6.1.4.1.119.2.3.14.9.4.5.1 | ||
| Entry of ATMSoft-PVPC/PVCC connection | |||
| OBJECT-TYPE | |||
| ConnSoftPvcEntry | |||
| connSoftPvcIndex | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.1 | ||
| The value of this object is equal to the connSoftPvcIndexNext. 1 - 128 : Soft PVPCs/PVCCs | |||
| OBJECT-TYPE | |||
| INTEGER | 1..128 | ||
| connSoftPvcTopology | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.2 | ||
| Topology of the Connection. | |||
| OBJECT-TYPE | |||
| INTEGER | bi-directional-VCC(2), bi-directional-VPC(4) | ||
| connSoftPvcTrafficType | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.3 | ||
| Traffic Type. | |||
| OBJECT-TYPE | |||
| INTEGER | traffic-CBR(1), traffic-rt-VBR(2), traffic-nrt-VBR(3), traffic-ABR(4), traffic-UBR(5) | ||
| connSoftPvcEndpointType | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.4 | ||
| Type of Endpoint. | |||
| OBJECT-TYPE | |||
| INTEGER | calling(1), called(2) | ||
| connSoftPvcRetry | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.5 | ||
| Number of retry. 0 - 15 : Number of retry -1 : Infinite retry | |||
| OBJECT-TYPE | |||
| INTEGER | 0..15 | -1 | ||
| connSoftPvcSrcAtmAddressFormat | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.6 | ||
| AtmAdress format. | |||
| OBJECT-TYPE | |||
| ConnSoftPvcSrcAtmAddressFormat | |||
| connSoftPvcSrcAtmAddressLength | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.7 | ||
| The valid bit length of connSoftPvcSrcAtmAddress. The value(-1) is read-only. The value(4..160) must be a multiple of 4. | |||
| OBJECT-TYPE | |||
| INTEGER | 4..160 | -1 | ||
| connSoftPvcSrcAtmAddress | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.8 | ||
| NodeId of source node. Its maximum length is 13 bytes. This object length is 20 bytes in case AtmAddress is setting. If the last semi OCTET is invalid, it is padded with 0xf. The value of size(0) is read-only. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..20) | ||
| connSoftPvcSrcIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.9 | ||
| The number of the calling line. (ifIndex of ifEntry) | |||
| OBJECT-TYPE | |||
| INTEGER | 1..99 | -1 | ||
| connSoftPvcSrcVPI | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.10 | ||
| VPI value of the calling line. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connSoftPvcSrcVCI | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.11 | ||
| VCI value of the calling line. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connSoftPvcDstAtmAddressFormat | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.12 | ||
| AtmAdress format. | |||
| OBJECT-TYPE | |||
| ConnSoftPvcDstAtmAddressFormat | |||
| connSoftPvcDstAtmAddressLength | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.13 | ||
| The valid bit length of connSoftPvcDstAtmAddress. The value(-1) is read-only. The value(4..160) must be a multiple of 4. | |||
| OBJECT-TYPE | |||
| INTEGER | 4..160 | -1 | ||
| connSoftPvcDstAtmAddress | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.14 | ||
| NodeId of destination node. Its maximum length is 13 bytes. This object length is 20 bytes in case AtmAddress is setting. If the last semi OCTET is invalid, it is padded with 0xf. The value of size(0) is read-only. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..20) | ||
| connSoftPvcDstIfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.15 | ||
| The number of the called line. (ifIndex of ifEntry)65 is GateWay. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..99 | -1 | ||
| connSoftPvcDstVPI | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.16 | ||
| VPI value of the called line. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connSoftPvcDstVCI | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.17 | ||
| VCI value of the called line. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connSoftPvcRowStatus | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.18 | ||
| It is used from the manager to order the setting method of the Soft PVC connection. It is used from the agent side to return the result of the connection setting request. - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device; - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row but not to have it available for use by the managed device; and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6) | ||
| connSoftPvcCause | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.19 | ||
| Object to indicate the result of the connection setting. | |||
| OBJECT-TYPE | |||
| INTEGER | rowExisting(1), vpivciSrcBusy(2), vpivciDstBusy(3), vpivciOutOfRange(4), rateSrcOverFlow(5), rateDstOverFlow(6), dataTableFull(7), inconsistentVPVC(8), lineDiagnosis(9), missMatchTrfType(10), illegalSrcFileName(11), illegalDstFileName(12), lineOutOfOrder(13), illegalSrcShaper(14), illegalOperation(15), parameterIsNotEnough(16), diagnostics(17), otherFailure(18), illegalSrcRateForUPC(19), noCevc(20), noDlci(21), noSrcShaperForGateway(22), noPvcSrcShaperForGateway(23), missMatchTrfTypeSrcShaperForGateway(24), insusfficientPCRofProfile(25) | ||
| connSoftPvcRestRetry | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.20 | ||
| Remaining number of retry 0 - 15 : Remaining number of retry -1 : Infinite retry in progress | |||
| OBJECT-TYPE | |||
| INTEGER | 0..15 | -1 | ||
| connSoftPvcSrcFifoIndex | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.21 | ||
| Designate the Shaper number of the calling line. If the Shaping is not performed, designate 0. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..16 | ||
| connSoftPvcDstFifoIndex | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.22 | ||
| Designate the Shaper number of the called line. If the Shaping is not performed, designate 0. However, if the called sw is not furnished with the shaping function, this value has no meaning. Since it cannot be recognized if this value is set on the called side, the value is regarded as 'the value set by the calling side'. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..16 | ||
| connSoftPvcNodeKind | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.23 | ||
| Designate/indicate the machine type on the called side. | |||
| OBJECT-TYPE | |||
| INTEGER | model5(1), model7(2), model5E(3) | ||
| connSoftPvcSrcParam1 | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.24 | ||
| UPC mode of the calling line. | |||
| OBJECT-TYPE | |||
| INTEGER | off(1), mode1(2), mode2(3), mode3(4), mode4(5), mode5(6) | ||
| connSoftPvcDstParam1 | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.25 | ||
| UPC mode of the called line. | |||
| OBJECT-TYPE | |||
| INTEGER | off(1), mode1(2), mode2(3), mode3(4), mode4(5), mode5(6) | ||
| connSoftPvcSrcParam2 | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.26 | ||
| Profile name of Forward. If nothing is designated, the string of size(0) is designated. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..10 | 0) | ||
| connSoftPvcDstParam2 | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.27 | ||
| Profile name of Backward. If nothing is designated, the string of size(0) is designated. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..10 | 0) | ||
| connSoftPvcSrcParam3 | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.28 | ||
| PCR[cell/s] of Forward. If the value is invalid, -1 is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connSoftPvcDstParam3 | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.29 | ||
| PCR[cell/s] of Backward. If the value is invalid, -1 is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connSoftPvcSrcParam4 | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.30 | ||
| SCR[cell/s] of Forward. If the value is invalid, -1 is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connSoftPvcDstParam4 | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.31 | ||
| SCR[cell/s] of Backward. If the value is invalid, -1 is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connSoftPvcSrcParam5 | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.32 | ||
| MBS[cell] of Forward. If the value is invalid, -1 is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connSoftPvcDstParam5 | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.33 | ||
| MBS[cell] of Backward. If the value is invalid, -1 is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connSoftPvcSrcParam6 | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.34 | ||
| EPD(Early Packet Discard) of Forward. Indicate if the discard processing in the unit of AAL5 packet should be performed or not when the threshold is exceeded. If the value is invalid, off(2) is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| connSoftPvcDstParam6 | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.35 | ||
| EPD(Early Packet Discard) of Backward. Indicate if the discard processing in the unit of AAL5 packet should be performed or not when the threshold is exceeded. If the value is invalid, off(2) is indicated. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| connSoftPvcSrcParam7 | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.36 | ||
| MCR[cell/s]. Not supported here. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connSoftPvcDstParam7 | 1.3.6.1.4.1.119.2.3.14.9.4.5.1.37 | ||
| MCR[cell/s]. Not supported here. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connSoftPvcEstablishedSrcInfTable | 1.3.6.1.4.1.119.2.3.14.9.4.6 | ||
| The table regarding the calling node of the Soft PVPC/PVCC established as called side office by the local node | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ConnSoftPvcEstablishedSrcInfEntry | |||
| connSoftPvcEstablishedSrcInfEntry | 1.3.6.1.4.1.119.2.3.14.9.4.6.1 | ||
| The entry of the calling side node information of the Soft PVPC/PVCC established as the called side office by the local node | |||
| OBJECT-TYPE | |||
| ConnSoftPvcEstablishedSrcInfEntry | |||
| connSoftPvcEstablishedSrcInf | 1.3.6.1.4.1.119.2.3.14.9.4.6.1.1 | ||
| The calling node information of the Soft PVPC/PVCC established as called side office by the node. The structure of the entry is as follows struct { long SrcAtmAddressFormat; long SrcAtmAddressLength; char SrcAtmAddress[20]; }; (*1) 'long' data should be stored with 'big endian'. (*2) For SrcAtmAddress data, if it is less than 20 byte, the data padded by '0xf' shall be stored. This information is divided into up to 32 pieces, and each piece is put into the head 4 bytes (count) of an entry. The data which contains the number of the entries is described below. +-----------------+ | count | (= n) +-----------------+ | EstSrcInf 1 | |.................| | EstSrcInf 2 | |.................| | . | | . | | . | |.................| | EstSrcInf n | ( 1 <= n <= 32 ) +-----------------+ | |||
| OBJECT-TYPE | |||
| Opaque | |||
| connSoftPvcEstSrcInfIndex | 1.3.6.1.4.1.119.2.3.14.9.4.6.1.2 | ||
| OBJECT-TYPE | |||
| ConnSoftPvcEstSrcInfIndex | |||
| connOam | 1.3.6.1.4.1.119.2.3.14.9.4.7 | ||
| OBJECT IDENTIFIER | |||
| connOamOpe | 1.3.6.1.4.1.119.2.3.14.9.4.7.1 | ||
| OBJECT IDENTIFIER | |||
| connOamOpeStatus | 1.3.6.1.4.1.119.2.3.14.9.4.7.1.1 | ||
| Used to set/delete OAM End-point, Connecting-point. | |||
| OBJECT-TYPE | |||
| INTEGER | allocate(1), add(2), delete(3), free(4) | ||
| connOamOpeCause | 1.3.6.1.4.1.119.2.3.14.9.4.7.1.2 | ||
| The result of the processing to set/delete OAM End-point, Connecting-point. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), succeed(2), parameterIsNotEnough(3), tableIsFull(4), illegalPoint(5), illegalMode(6), illegalSection(7), illegalPort(8), illegalVpiVci(9), invalidBufferType(10), noSuchConnection(11), alreadyRegistered(12), notExisting(13) | ||
| connOamOpePoint | 1.3.6.1.4.1.119.2.3.14.9.4.7.1.3 | ||
| End-point / Connecting-point. | |||
| OBJECT-TYPE | |||
| INTEGER | end-point(1), connecting-point(2) | ||
| connOamOpeMode | 1.3.6.1.4.1.119.2.3.14.9.4.7.1.4 | ||
| Mode. F4 (VP level)/f5 (VC level) | |||
| OBJECT-TYPE | |||
| INTEGER | f4(1), f5(2) | ||
| connOamOpeSection | 1.3.6.1.4.1.119.2.3.14.9.4.7.1.5 | ||
| Point between segments/End-to-End point. | |||
| OBJECT-TYPE | |||
| INTEGER | segment(1), end-to-end(2) | ||
| connOamOpePort1 | 1.3.6.1.4.1.119.2.3.14.9.4.7.1.6 | ||
| Line number | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connOamOpePort2 | 1.3.6.1.4.1.119.2.3.14.9.4.7.1.7 | ||
| Line number. Upon setting/deleting end-point, don't care about it. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connOamOpeVpi1 | 1.3.6.1.4.1.119.2.3.14.9.4.7.1.8 | ||
| VPI. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connOamOpeVpi2 | 1.3.6.1.4.1.119.2.3.14.9.4.7.1.9 | ||
| VPI. Upon setting/deleting end-point, don't care about it. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connOamOpeVci1 | 1.3.6.1.4.1.119.2.3.14.9.4.7.1.10 | ||
| VCI. JpnToEng[f4 レベル の設定/削除時は Don't care.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connOamOpeVci2 | 1.3.6.1.4.1.119.2.3.14.9.4.7.1.11 | ||
| VCI. JpnToEng[End-point または f4 レベル の設定/削除時は Don't care.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connOamTable | 1.3.6.1.4.1.119.2.3.14.9.4.7.2 | ||
| OAM End-point, Connecting-point indication table | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ConnOamEntry | |||
| connOamEntry | 1.3.6.1.4.1.119.2.3.14.9.4.7.2.1 | ||
| OAM End-point, Connecting-point indication entry | |||
| OBJECT-TYPE | |||
| ConnOamEntry | |||
| connOamPort | 1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.1 | ||
| Line number | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connOamIndex | 1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.2 | ||
| OAM End-point / Connecting-point Index. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..144 | ||
| connOamContrastPort | 1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.3 | ||
| Line number of the opposite line. For End-point, -1. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connOamVpi | 1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.4 | ||
| VPI. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connOamContrastVpi | 1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.5 | ||
| Opposite VPI. For End-point, -1. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connOamVci | 1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.6 | ||
| VCI. For the f4 level, -1. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connOamContrastVci | 1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.7 | ||
| Opposite VCI. JpnToEng[End-point または f4レベルの場合は -1.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connOamPoint | 1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.8 | ||
| End-point / Connecting-point. | |||
| OBJECT-TYPE | |||
| INTEGER | end-point(1), connecting-point(2) | ||
| connOamMode | 1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.9 | ||
| Mode. F4 (VP level)/f5 (VC level). | |||
| OBJECT-TYPE | |||
| INTEGER | f4(1), f5(2) | ||
| connOamSection | 1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.10 | ||
| Point between segments/End-to-End point. | |||
| OBJECT-TYPE | |||
| INTEGER | segment(1), end-to-end(2) | ||
| connOamStatus | 1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.11 | ||
| Receive status of end-point. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), normal(2), receive-AIS(3), receive-RDI(4), failure(5) | ||
| connOamDefectType | 1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.12 | ||
| Fault cause in the receive cell. For Connecting-point, return 'normal (1)'. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), los(2), lof(3), loc(4), ais-path(5), ais-section(6), yellow-section(7), yellow-path(8), lop(9), ais(10), payload-all-one(11), rai(12), oof(13), idle(14), rdi(15), plcp-oof(16), plcp-lof(17), plcp-yellow(18), red(19) | ||
| connOamDefectNodeID | 1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.13 | ||
| Node ID of the Switch which sends alarm transfer cells. For connecting-point, return '0 length string'. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(13) | ||
| connLoop | 1.3.6.1.4.1.119.2.3.14.9.4.8 | ||
| OBJECT IDENTIFIER | |||
| connLoopOpe | 1.3.6.1.4.1.119.2.3.14.9.4.8.1 | ||
| OBJECT IDENTIFIER | |||
| connLoopOpeStatus | 1.3.6.1.4.1.119.2.3.14.9.4.8.1.1 | ||
| JpnToEng[ループバック試験の操作.] | |||
| OBJECT-TYPE | |||
| INTEGER | allocate(1), action(2), endtest(3), free(4) | ||
| connLoopOpeCause | 1.3.6.1.4.1.119.2.3.14.9.4.8.1.2 | ||
| JpnToEng[ループバック試験の結果.] | |||
| OBJECT-TYPE | |||
| INTEGER | succeed(1), abort(2), other(3), vpivciOutOfRange(4), parameterFailed(5), admindown(6), nonePkg(7), noneBuffer2(8), lineLoopback(9), resetSlot(10), noneLoopBackId(11), execute(12) | ||
| connLoopOpeMode | 1.3.6.1.4.1.119.2.3.14.9.4.8.1.3 | ||
| F4 (VP level)/f5 (VC level). | |||
| OBJECT-TYPE | |||
| INTEGER | f4(1), f5(2) | ||
| connLoopOpeBase | 1.3.6.1.4.1.119.2.3.14.9.4.8.1.4 | ||
| JpnToEng[テストベースのフロー.] | |||
| OBJECT-TYPE | |||
| INTEGER | segment(1), end-end(2) | ||
| connLoopOpeLoopBackPointNodeId | 1.3.6.1.4.1.119.2.3.14.9.4.8.1.5 | ||
| JpnToEng[ループバックセルを折り返す Switch の LoopBackID.] | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| connLoopOpeCorrelationTag | 1.3.6.1.4.1.119.2.3.14.9.4.8.1.6 | ||
| JpnToEng[送信したセルと受信したセルを 対応付けるための情報.] | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| connLoopOpeCount | 1.3.6.1.4.1.119.2.3.14.9.4.8.1.7 | ||
| JpnToEng[ループバック試験の実施回数.] | |||
| OBJECT-TYPE | |||
| INTEGER | 1..16 | ||
| connLoopOpePort | 1.3.6.1.4.1.119.2.3.14.9.4.8.1.8 | ||
| JpnToEng[送出元の回線番号.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connLoopOpeVpi | 1.3.6.1.4.1.119.2.3.14.9.4.8.1.9 | ||
| JpnToEng[送出元の VPI.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connLoopOpeVci | 1.3.6.1.4.1.119.2.3.14.9.4.8.1.10 | ||
| JpnToEng[送出元の VCI. f4 (VPレベル) での処理時は Don't care とする.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connLoopOpeNormalEndCount | 1.3.6.1.4.1.119.2.3.14.9.4.8.1.11 | ||
| JpnToEng[ループバック試験正常終了回数.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connLoopOpeAbnormalEndCount | 1.3.6.1.4.1.119.2.3.14.9.4.8.1.12 | ||
| JpnToEng[ループバック試験異常終了回数.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connLoopOpeAbortCount | 1.3.6.1.4.1.119.2.3.14.9.4.8.1.13 | ||
| JpnToEng[ループバック試験中断回数.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connLoopOpeLoopBackPointIdLength | 1.3.6.1.4.1.119.2.3.14.9.4.8.1.14 | ||
| JpnToEng[ループバックセルを折り返す Switch の LoopBack Location ID の入力サイズ(bit長).ただし,4ビット単位できりあげ.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connProfile | 1.3.6.1.4.1.119.2.3.14.9.4.9 | ||
| OBJECT IDENTIFIER | |||
| connProfileIndexNext | 1.3.6.1.4.1.119.2.3.14.9.4.9.1 | ||
| Shows the empty index value of connProfileTable(including row of notReady, notInService). If the number of profiles reaches the registration limit, 0. | |||
| OBJECT-TYPE | |||
| ConnProfileIndex | |||
| connProfileTable | 1.3.6.1.4.1.119.2.3.14.9.4.9.2 | ||
| Table to set/indicate the profile. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ConnProfileEntry | |||
| connProfileEntry | 1.3.6.1.4.1.119.2.3.14.9.4.9.2.1 | ||
| Entry of connProfileTable. | |||
| OBJECT-TYPE | |||
| ConnProfileEntry | |||
| connProfileIndex | 1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.1 | ||
| Index value of connProfileTable. | |||
| OBJECT-TYPE | |||
| ConnProfileIndex | |||
| connProfileRowStatus | 1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.2 | ||
| Used to control rows of the table. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6) | ||
| connProfileCause | 1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.3 | ||
| The result of Profile setting processing. | |||
| OBJECT-TYPE | |||
| INTEGER | rowExisting(1), otherFailure(2), inconsistentEpd(3), parameterNotEnough(4), alreadyExist(5), duplicateName(6), inconsistentRate(7) | ||
| connProfileTrafficType | 1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.4 | ||
| Traffic Type. | |||
| OBJECT-TYPE | |||
| INTEGER | traffic-CBR(1), traffic-rt-VBR(2), traffic-nrt-VBR(3), traffic-ABR(4), traffic-UBR(5) | ||
| connProfileName | 1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.5 | ||
| Profile name. Available characters: alphanumeric characters 0 length string is only read. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0 | 1..10) | ||
| connProfileParam1 | 1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.6 | ||
| For ph1/2-buffer, peek cell rate [cell/sec]. If it is invalid, -1. JpnToEng[ABR で -1 の場合は, 帯域確保/UPCの設定をしないことを示す.] | |||
| OBJECT-TYPE | |||
| INTEGER | -1 | 1..1412830 | ||
| connProfileParam2 | 1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.7 | ||
| For ph1/2-buffer, Sustainable cell rate [cell/sec]. Only nrt-VBR, and rt-VBR are valid. If it is invalid, -1. | |||
| OBJECT-TYPE | |||
| INTEGER | -1 | 1..1412830 | ||
| connProfileParam3 | 1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.8 | ||
| For ph1/2-buffer, Maximum burst size [cell]. Only nrt-VBR, and rt-VBR are valid. If it is invalid, -1. | |||
| OBJECT-TYPE | |||
| INTEGER | -1 | 1..1412830 | ||
| connProfileParam4 | 1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.9 | ||
| For ph1/2-buffer, EPD function flag. If it is other than ABR, UBR, off, only. | |||
| OBJECT-TYPE | |||
| INTEGER | off(1), on(2) | ||
| connProfileName2Index | 1.3.6.1.4.1.119.2.3.14.9.4.9.3 | ||
| Equivalent to connProfileName | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0 | 1..10) | ||
| connProfileName2IndexResult | 1.3.6.1.4.1.119.2.3.14.9.4.9.4 | ||
| Shows the index of the row whose connProfileRowStatus in connProfileTable, corresponding to connProfileName2Index, is active. If the corresponding row does not exist, 0. | |||
| OBJECT-TYPE | |||
| ConnProfileIndex | |||
| connSvcTable | 1.3.6.1.4.1.119.2.3.14.9.4.10 | ||
| JpnToEng[本装置に設定される SVC 情報のテーブル.] | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ConnSvcEntry | |||
| connSvcEntry | 1.3.6.1.4.1.119.2.3.14.9.4.10.1 | ||
| JpnToEng[本装置に設定される SVC 情報のエントリ.] | |||
| OBJECT-TYPE | |||
| ConnSvcEntry | |||
| connSvcIndex | 1.3.6.1.4.1.119.2.3.14.9.4.10.1.1 | ||
| JpnToEng[SVC 情報の Index.] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connSvcInf | 1.3.6.1.4.1.119.2.3.14.9.4.10.1.2 | ||
| JpnToEng(次の135行分を) -- SVC の情報. -- エントリの構造は以下の通り. -- Bits -- 8 7 6 5 4 3 2 1 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | 格納されている SVC 数 | 1 - 4 Octets -- +===============================================+ -- | 入側回線番号 | 1 - 2 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | 入側 VPI 番号 | 3 - 4 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | 入側 VCI 番号 | 5 - 6 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | 出側回線番号 | 7 - 8 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | 出側 VPI 番号 | 9 - 10 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | 出側 VCI 番号 | 11 - 12 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | 方向 | 種別 | Traffic Type | 13 -- | (注1) | (注2) | (注3) | -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | Calling Party | Called Party | 14 -- | Address Format | Address Format | -- | (注4) | (注4) | -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | Calling Party Address Length [bits] | 15 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | Called Party Address Length [bits] | 16 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | Calling Party Address | 17 - 36 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | Called Party Address | 37 - 56 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | 入側 Shaper 番号 (注5) | 57 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | 出側 Shaper 番号 (注5) | 58 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | 入側 UPC Mode | 出側 UPC Mode | Tag-| Tag-| 59 -- | (注6) | (注6) | ging| ging| -- | | | Fwd | Bwd | -- | | |(注7)|(注7)| -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | Fwd | Bwd | | 60 -- | EPD | EPD | Dummy1 | -- |(注8)|(注8)| | -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | Forward PCR [cell/s] | 61 - 64 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | Backward PCR [cell/s] | 65 - 68 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | Forward SCR [cell/s] | 69 - 72 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | Backward SCR [cell/s] | 73 - 76 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | Forward MBS [cells] | 77 - 80 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | Backward MBS [cells] | 81 - 84 -- +===============================================+ -- | 入側回線番号 | -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | 入側 VPI 番号 | -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | 入側 VCI 番号 | -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- : : -- : : -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | Backward MBS | -- +-----------------------------------------------+ -- -- (注1) 方向 -- 1: PtoP, 2: PtoMP-out, 3: PtoMP-in -- (注2) 種別 -- 0: PtoP, 1: PtoMP -- (注3) Traffic Type -- 1: CBR, 2: rt-VBR, 3: nrt-VBR, 4: ABR, 5: UBR -- (注4) Calling/Called Party Address Format -- 1: E.164, 2: NSAP -- (注5) 入/出側 Shaper 番号 -- 0: Shaping OFF, 1-16: Shaper 番号 -- (注6) 入/出側 UPC Mode -- 0: UPC OFF, 1-5: mode1-mode5 -- (注7) Tagging Forward/Backward -- 0: OFF, 1: ON -- (注8) EPD -- 0: OFF, 1: ON -- -- struct atmSvc { -- unsigned short AtmSvcIncomingPort ; -- unsigned short AtmSvcIncomingVpi ; -- unsigned short AtmSvcIncomingVci ; -- unsigned short AtmSvcOutgoingPort ; -- unsigned short AtmSvcOutgoingVpi ; -- unsigned short AtmSvcOutgoingVci ; -- unsigned char AtmSvcDirection : 2 ; -- unsigned char AtmSvcTopology : 2 ; -- unsigned char AtmSvcTrafficType : 4 ; -- unsigned char AtmSvcCallingAddressFormat : 4 ; -- unsigned char AtmSvcCalledAddressFormat : 4 ; -- unsigned char AtmSvcCallingAddressLength ; -- unsigned char AtmSvcCalledAddressLength ; -- unsigned char AtmSvcCallingAddress[ 20 ] ; -- unsigned char AtmSvcCalledAddress[ 20 ] ; -- unsigned char AtmSvcIncomingShaper ; -- unsigned char AtmSvcOutgoingShaper ; -- unsigned char AtmSvcIncomingUpcMode : 3 ; -- unsigned char AtmSvcOutgoingUpcMode : 3 ; -- unsigned char AtmSvcForwardTagging : 1 ; -- unsigned char AtmSvcBackwardTagging : 1 ; -- unsigned char AtmSvcForwardEpd : 1 ; -- unsigned char AtmSvcBackwardEpd : 1 ; -- unsigned char Dummy1 : 6 ; -- long AtmSvcForwardPcr ; -- long AtmSvcBackwardPcr ; -- long AtmSvcForwardScr ; -- long AtmSvcBackwardScr ; -- long AtmSvcForwardMbs ; -- long AtmSvcBackwardMbs ; -- } ; -- -- struct opaqueSvc { -- long count ; -- struct atmSvc atmSvc[ 16 ] ; -- } ; -- -- 各データは Big Endian で格納される. -- AtmSvcCallingAddress/CalledAddress が 20 byte に満たない場合, -- 不足部分は 0 で padding される. -- -- SVC 情報は, 最大 16 個ずつまとめられ, 先頭に格納データ数を -- 表す 4 byte のデータが付与される. -- -- SVC 情報は動的なデータであるため, 情報を参照するときは -- 連続的に最初から参照しないと情報の正確性は保証できない. | |||
| OBJECT-TYPE | |||
| Opaque | |||
| connCe | 1.3.6.1.4.1.119.2.3.14.9.4.11 | ||
| OBJECT IDENTIFIER | |||
| connCeVc | 1.3.6.1.4.1.119.2.3.14.9.4.11.1 | ||
| OBJECT IDENTIFIER | |||
| connCeVcTable | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1 | ||
| JpnToEng[CESカードに設定されたCEVCの情報表示を行なう.] | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ConnCeVcEntry | |||
| connCeVcEntry | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1 | ||
| JpnToEng[本装置に設定される全てのCEVCのエントリー.] | |||
| OBJECT-TYPE | |||
| ConnCeVcEntry | |||
| connCeVcPort | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.1 | ||
| Line number. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connCeVcVci | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.2 | ||
| VCI value. JpnToEng[使用可能範位はlinfStatusTable 参照.] | |||
| OBJECT-TYPE | |||
| INTEGER | 32..383 | ||
| connCeVcRowStatus | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.3 | ||
| Used to control rows of the table. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6) | ||
| connCeVcCause | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.4 | ||
| The result of CEVC setting processing. | |||
| OBJECT-TYPE | |||
| INTEGER | rowExisting(1), otherFailure(2), parameterNotEnough(3), illegalpkg(4), vcsOverFllow(5), tssOverFllow(6), alreadyAssignedTs(7), inconsistentTss(8), illegalTimeslot(9), illegalPort(10), illegalVci(11), illegalUpPartialFillSize(12), illegalDownPartialFillSize(13), illegalCdvt(14) | ||
| connCeVcDirection | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.5 | ||
| JpnToEng[設定方向] | |||
| OBJECT-TYPE | |||
| INTEGER | bi(1), up(2), down(3) | ||
| connCeVcUpPartialFillSize | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.6 | ||
| JpnToEng[UP方向のセル当たりの満たされた平均ユーザオクテット数 0 の場合は full 設定(structure の時は46.875になる) 0 以外の最小値は,設定TS数+1.] | |||
| OBJECT-TYPE | |||
| INTEGER | -1 | 0..47 | ||
| connCeVcDownPartialFillSize | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.7 | ||
| JpnToEng[DOWN方向のセル当たりの満たされた平均ユーザオクテット数 0 の場合は full 設定(structure の時は46.875になる) 0 以外の最小値は,設定TS数+1.] | |||
| OBJECT-TYPE | |||
| INTEGER | -1 | 0..47 | ||
| connCeVcCondition | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.8 | ||
| Condtion date. | |||
| OBJECT-TYPE | |||
| INTEGER | -1 | 0..255 | ||
| connCeVcCDVT | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.9 | ||
| CDVT value. JpnToEng[pkg種別によるCDVT範囲] +----------------------+----------+------------+ |pkg type| str mode |CDVT range| unit of | | | | | setting | ================================================ | CE-J2 | unstructure | 1..73 | 125μsec | | +-------------+----------+------------+ | | structure | 1..7218 | 125μsec | +--------+-------------+----------+------------+ | CE-DS1 | unstructure | 1..255 | 165.8μsec | | +-------------+----------+------------+ | | structure | 1..191 | 125μsec | +--------+-------------+----------+------------+ | CE-E1 | unstructure | 1..255 | 124.5μsec | | +-------------+----------+------------+ | | structure | 1..255 | 125μsec | +--------+-------------+----------+------------+ | CE-DS3 | unstructure | 1..255 | 5.7μsec | +--------+-------------+----------+------------+ | |||
| OBJECT-TYPE | |||
| INTEGER | -1 | 1..7218 | ||
| connCeVcUpPCR | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.10 | ||
| JpnToEng[CEVC設定時のUP方向のPCR値.] | |||
| OBJECT-TYPE | |||
| INTEGER | -1 | 0..118979 | ||
| connCeVcDownPCR | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.11 | ||
| JpnToEng[CEVC設定時のDOWN方向のPCR値.] | |||
| OBJECT-TYPE | |||
| INTEGER | -1 | 0..118979 | ||
| connCeVcUpTimeSlot1 | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.12 | ||
| JpnToEng(次の12行分) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connCeVcDownTimeSlot1 | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.13 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connCeVcUpTimeSlot2 | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.14 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connCeVcDownTimeSlot2 | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.15 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connCeVcUpTimeSlot3 | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.16 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connCeVcDownTimeSlot3 | 1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.17 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connFr | 1.3.6.1.4.1.119.2.3.14.9.4.12 | ||
| OBJECT IDENTIFIER | |||
| connFrDlci | 1.3.6.1.4.1.119.2.3.14.9.4.12.1 | ||
| OBJECT IDENTIFIER | |||
| connFrDlciTable | 1.3.6.1.4.1.119.2.3.14.9.4.12.1.1 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ConnFrDlciEntry | |||
| connFrDlciEntry | 1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1 | ||
| Entry of connFrDlciTable. | |||
| OBJECT-TYPE | |||
| ConnFrDlciEntry | |||
| connFrDlciPort | 1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.1 | ||
| Line number. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..64 | ||
| connFrDlciIndex | 1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.2 | ||
| DLCI number. | |||
| OBJECT-TYPE | |||
| INTEGER | 16..1007 | ||
| connFrDlciRowStatus | 1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.3 | ||
| Used to control rows of the table. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6) | ||
| connFrDlciCause | 1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.4 | ||
| JpnToEng[コネクション(DLCI) 設定データ 設定処理の結果.] | |||
| OBJECT-TYPE | |||
| INTEGER | rowExisting(1), otherFailure(2), noFrProfile(3), inconsistentInterWorking(4), totalCIROverFlow(5), lineDiagnosticsFailure(6), illegalPort(7), illegalDlci(8), pvcsOverFlow(9) | ||
| connFrDlciFrProfile | 1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.5 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0 | 1..10) | ||
| connFrDlciPCR | 1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.6 | ||
| Peak Cell Rate[cell/sec]. JpnToEng[rowがactiveでない場合の値は -1(デフォルト値).] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connFrDlciSCR | 1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.7 | ||
| Sustainable Cell Rate[cell/sec]. JpnToEng[rowがactiveでない場合の値は -1(デフォルト値).] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connFrDlciMBS | 1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.8 | ||
| Maximum Burst Size[cell]. JpnToEng[rowがactiveでない場合の値は -1(デフォルト値).] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| connFrProfile | 1.3.6.1.4.1.119.2.3.14.9.4.12.2 | ||
| OBJECT IDENTIFIER | |||
| connFrProfileIndexNext | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.1 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| ConnFrProfileIndex | |||
| connFrProfileTable | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.2 | ||
| JpnToEng[Frprofile の設定 / 表示を行なうためのテーブル.] | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ConnFrProfileEntry | |||
| connFrProfileEntry | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1 | ||
| Entry of connFrProfileTable. | |||
| OBJECT-TYPE | |||
| ConnFrProfileEntry | |||
| connFrProfileIndex | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.1 | ||
| Index of connFrProfileTable. | |||
| OBJECT-TYPE | |||
| ConnFrProfileIndex | |||
| connFrProfileRowStatus | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.2 | ||
| Used to control rows of the table. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6) | ||
| connFrProfileCause | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.3 | ||
| The result of Frprofile setting processing. | |||
| OBJECT-TYPE | |||
| INTEGER | rowExisting(1), otherFailure(2), parameterNotEnough(3), alreadyExist(4), duplicateName(5) | ||
| connFrProfileName | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.4 | ||
| Frprofile name. Available characters: alphanumeric characters 0 length string is only read. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0 | 1..10) | ||
| connFrProfileInterworkingType | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.5 | ||
| Interworking Type | |||
| OBJECT-TYPE | |||
| INTEGER | network(1), service(2) | ||
| connFrProfileCIR | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.6 | ||
| CIR value. | |||
| OBJECT-TYPE | |||
| INTEGER | -1 | 1..1984 | ||
| connFrProfileDEtoCLP | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.7 | ||
| DE to CLP mapping mode | |||
| OBJECT-TYPE | |||
| INTEGER | mode1(1), mode2(2) | ||
| connFrProfileCLPValue | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.8 | ||
| CLP Value. It's valid when connFrProfileDEtoCLP is mode2. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), on(2), off(3) | ||
| connFrProfileCLPtoDE | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.9 | ||
| CLP to DE mapping mode. | |||
| OBJECT-TYPE | |||
| INTEGER | mode1(1), mode2(2) | ||
| connFrProfileDEValue | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.10 | ||
| DE Value. It's valid when connFrProfileInterworkingType is service and connFrProfileCLPtoDE is mode2. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), on(2), off(3) | ||
| connFrProfileCapsulationMode | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.11 | ||
| Protocol encapsulation mode. It's valid when connFrProfileInterworkingType is service. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), transparent(2), translation(3) | ||
| connFrProfileCongestionMode | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.12 | ||
| Congestion indication(Forward) mode. It's valid when connFrProfileInterworkingType is service. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), mode1(2), mode2(3) | ||
| connFrProfileName2Index | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.3 | ||
| Equivalent to connProfileName. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0 | 1..10) | ||
| connFrProfileName2IndexResult | 1.3.6.1.4.1.119.2.3.14.9.4.12.2.4 | ||
| Shows the index of the row whose connFrProfileRowStatus in connFrProfileTable, corresponding to connFrProfileName2Index, is active. If the corresponding row does not exist, 0. | |||
| OBJECT-TYPE | |||
| ConnFrProfileIndex | |||
| perf | 1.3.6.1.4.1.119.2.3.14.9.5 | ||
| OBJECT IDENTIFIER | |||
| perfTrapEnable | 1.3.6.1.4.1.119.2.3.14.9.5.1 | ||
| This object is used for disabling/enabling trap messages regarding the enterprise specific traps. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| perfIfTable | 1.3.6.1.4.1.119.2.3.14.9.5.2 | ||
| Table for showing the result of the performance monitoring per line of the equipment. Up to 64 tables are available for entry. Every line whose traffic is managed per line is provided with an entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PerfIfEntry | |||
| perfIfEntry | 1.3.6.1.4.1.119.2.3.14.9.5.2.1 | ||
| Entry of the line performance monitoring. | |||
| OBJECT-TYPE | |||
| PerfIfEntry | |||
| perfIfIndex | 1.3.6.1.4.1.119.2.3.14.9.5.2.1.1 | ||
| Line number. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfReceivedCells | 1.3.6.1.4.1.119.2.3.14.9.5.2.1.2 | ||
| The Number of the receive cells of line port. (64 bit applicable) | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| perfIfReceivedCellsCounters | 1.3.6.1.4.1.119.2.3.14.9.5.2.1.3 | ||
| The Number of the receive cells of line port. (32 bit applicable). | |||
| OBJECT-TYPE | |||
| Counter | |||
| perfIfTransmittedCells | 1.3.6.1.4.1.119.2.3.14.9.5.2.1.4 | ||
| The Number of the transmit cells of line port. (64 bit applicable). | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| perfIfTransmittedCellsCounters | 1.3.6.1.4.1.119.2.3.14.9.5.2.1.5 | ||
| The Number of the transmit cells of line port. (32 bit applicable). | |||
| OBJECT-TYPE | |||
| Counter | |||
| perfIfMisDelivdCells | 1.3.6.1.4.1.119.2.3.14.9.5.2.1.8 | ||
| The Number of the undefined cells of line port. (64 bit applicable). | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| perfIfMisDelivdCellsCounters | 1.3.6.1.4.1.119.2.3.14.9.5.2.1.9 | ||
| The Number of the undefined cells of line port. (32 bit applicable). | |||
| OBJECT-TYPE | |||
| Counter | |||
| perfIfThresholdExcessCells | 1.3.6.1.4.1.119.2.3.14.9.5.2.1.10 | ||
| Number of the threshold excess cells (64 bit applicable). | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| perfIfThresholdExcessCellsCounters | 1.3.6.1.4.1.119.2.3.14.9.5.2.1.11 | ||
| Number of the threshold excess cells (32 bit applicable). | |||
| OBJECT-TYPE | |||
| Counter | |||
| perfIfUpcErrorCells | 1.3.6.1.4.1.119.2.3.14.9.5.2.1.12 | ||
| Number of the UPC error cells (64 bit applicable). | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| perfIfUpcErrorCellsCounters | 1.3.6.1.4.1.119.2.3.14.9.5.2.1.13 | ||
| Number of the UPC error cells (32 bit applicable). | |||
| OBJECT-TYPE | |||
| Counter | |||
| perfIfSlotTable | 1.3.6.1.4.1.119.2.3.14.9.5.3 | ||
| Table for showing the number of cells of the traffic and performance per line card of the equipment. Up to 16 tables are available for entry. Every line whose traffic is managed per slot is provided with an entry. The object which becomes invalid by the line card is always 0. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PerfIfSlotEntry | |||
| perfIfSlotEntry | 1.3.6.1.4.1.119.2.3.14.9.5.3.1 | ||
| Entry of traffic/performance per line card. | |||
| OBJECT-TYPE | |||
| PerfIfSlotEntry | |||
| perfIfSlotReceivedCells | 1.3.6.1.4.1.119.2.3.14.9.5.3.1.1 | ||
| The number of receive cells. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| perfIfSlotTransmittedCells | 1.3.6.1.4.1.119.2.3.14.9.5.3.1.2 | ||
| The number of transmit cells. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| perfIfSlotInDropCells | 1.3.6.1.4.1.119.2.3.14.9.5.3.1.3 | ||
| The number of receive drop cells. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| perfIfSlotReceivedCellsCounters | 1.3.6.1.4.1.119.2.3.14.9.5.3.1.5 | ||
| The number of receive cells. | |||
| OBJECT-TYPE | |||
| Counter | |||
| perfIfSlotTransmittedCellsCounters | 1.3.6.1.4.1.119.2.3.14.9.5.3.1.6 | ||
| The number of transmit cells. | |||
| OBJECT-TYPE | |||
| Counter | |||
| perfIfSlotInDropCellsCounters | 1.3.6.1.4.1.119.2.3.14.9.5.3.1.7 | ||
| The number of receive drop cells. | |||
| OBJECT-TYPE | |||
| Counter | |||
| perfIfSlotHCThresholdExcessCells | 1.3.6.1.4.1.119.2.3.14.9.5.3.1.9 | ||
| The number of threshold excess cells | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| perfIfSlotThresholdExcessCells | 1.3.6.1.4.1.119.2.3.14.9.5.3.1.10 | ||
| The number of threshold excess cells | |||
| OBJECT-TYPE | |||
| Counter | |||
| perfIfSlotHCUpcErrorCells | 1.3.6.1.4.1.119.2.3.14.9.5.3.1.11 | ||
| Number of UPC error cells. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| perfIfSlotUpcErrorCells | 1.3.6.1.4.1.119.2.3.14.9.5.3.1.12 | ||
| Number of UPC error cells. | |||
| OBJECT-TYPE | |||
| Counter | |||
| perfIfPhysTable | 1.3.6.1.4.1.119.2.3.14.9.5.4 | ||
| JpnToEng[物理層パフォーマンスモニタを示すテーブル.] | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PerfIfPhysEntry | |||
| perfIfPhysEntry | 1.3.6.1.4.1.119.2.3.14.9.5.4.1 | ||
| JpnToEng[物理層パフォーマンスモニタのエントリ.] | |||
| OBJECT-TYPE | |||
| PerfIfPhysEntry | |||
| perfIfPhysPort | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.1 | ||
| Line number. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCHecErorrs | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.2 | ||
| Number of HEC error cells(64 bit applicable). On the line card other than OC12, J2 and PR-1.5M, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysHecErorrs | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.3 | ||
| Number of HEC error cells(32 bit applicable). On the line card other than OC12, J2 and PR-1.5M, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCHecDropCells | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.4 | ||
| Number of uncorrectable HEC error cells(64 bit applicable). On the line card other than OC3, OC12, OC12PMC, J2, PR-1.5, DS3, E3, DS1 and E1, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysHecDropCells | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.5 | ||
| Number of uncorrectable HEC error cells(32 bit applicable). On the line card other than OC3, OC12, OC12PMC, J2, PR-1.5, DS3, E3, DS1 and E1, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCB1Errors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.6 | ||
| Number of B1 errors(64 bit applicable). On the line card other than OC3, OC12, OC12PMC, DS3, E3, DS1 and E1, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysB1Errors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.7 | ||
| Number of B1 errors(32 bit applicable). On the line card other than OC3, OC12, OC12PMC, DS3, E3, DS1 and E1, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCB2Errors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.8 | ||
| Number of B2 errors(64 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysB2Errors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.9 | ||
| Number of B2 errors(32 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCB3Errors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.10 | ||
| Number of B3 errors(64 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysB3Errors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.11 | ||
| Number of B3 errors(32 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCPathFEBEs | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.12 | ||
| Number of Path FEBEs(64 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysPathFEBEs | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.13 | ||
| Number of Path FEBEs(32 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCLineFEBEs | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.14 | ||
| Number of Line (Section) FEBEs(64 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysLineFEBEs | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.15 | ||
| Number of Line (Section) FEBEs(32 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCFramingErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.16 | ||
| Number of Framing errors(64 bit applicable). On the line card other than DS1, E1, DS3 and E3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysFramingErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.17 | ||
| Number of Framing errors(32 bit applicable). On the line card other than DS1, E1, DS3 and E3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCReceivedCells | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.18 | ||
| The Number of the receive cells(64 bit applicable). On the line card other than DS3, E3 and OC12PMC, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysReceivedCells | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.19 | ||
| The Number of the receive cells(32 bit applicable). On the line card other than DS3, E3 and OC12PMC, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCTransmittedCells | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.20 | ||
| The Number of the transmit cells(64 bit applicable). On the line card other than DS3, E3 and OC12PMC, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysTransmittedCells | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.21 | ||
| The Number of the transmit cells(32 bit applicable). On the line card other than DS3, E3 and OC12PMC, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCIdelUnassignedCells | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.22 | ||
| The Number of Idle/Unassigned cells(64 bit applicable). On the line card other than DS3 and E3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysIdelUnassignedCells | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.23 | ||
| The Number of Idle/Unassigned cells(32 bit applicable). On the line card other than DS3 and E3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCFEBEErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.24 | ||
| Number of FEBE errors(64 bit applicable). On the line card other than DS3, E3, DS1 and E1, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysFEBEErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.25 | ||
| Number of FEBEs errors(32 bit applicable). On the line card other than DS3, E3, DS1 and E1, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCFEBEs | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.26 | ||
| Number of FEBEs(64 bit applicable). On the line card other than DS3, E3, E1 and CE-E1, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysFEBEs | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.27 | ||
| Number of FEBEs(32 bit applicable). On the line card other than DS3, E3, E1 and CE-E1, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCPathParityErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.28 | ||
| Number of path parity errors(64 bit applicable). On the line card other than DS3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysPathParityErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.29 | ||
| Number of path parity errors(32 bit applicable). On the line card other than DS3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCParityErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.30 | ||
| Number of parity errors(64 bit applicable). On the line card other than DS3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysParityErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.31 | ||
| Number of parity errors(32 bit applicable). On the line card other than DS3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCSEZs | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.32 | ||
| Number of detections of Summed excessive Zero (64 bit applicable). On the line card other than DS3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysSEZs | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.33 | ||
| Number of detections of Summed excessive Zero (32 bit applicable). On the line card other than DS3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCBitErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.34 | ||
| Number of Bit errors(64 bit applicable). On the line card other than DS3 and CE-DS1(SF mode), the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysBitErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.35 | ||
| Number of Bit errors(32 bit applicable). On the line card other than DS3 and CE-DS1(SF mode), the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCLcvErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.36 | ||
| Number of LCV errors(64 bit applicable). On the line card other than DS3, E3, DS1, E1, FR-E1, CE-DS1, FR-DS1 and CE-E1, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysLcvErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.37 | ||
| Number of LCV errors(32 bit applicable). On the line card other than DS3, E3, DS1, E1, FR-E1, CE-DS1, FR-DS1 and CE-E1, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCBip8Errors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.38 | ||
| Number of BIP-8 errors(64 bit applicable). On the line card other than E3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysBip8Errors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.39 | ||
| Number of BIP-8 errors(32 bit applicable). On the line card other than E3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCIecErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.40 | ||
| Number of IEC errors(64 bit applicable). On the line card other than E3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysIecErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.41 | ||
| Number of IEC errors(32 bit applicable). On the line card other than E3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCFramingPatternErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.42 | ||
| Number of Framing pattern errors(64 bit applicable). On the line card other than E3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysFramingPatternErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.43 | ||
| Number of Framing pattern errors(32 bit applicable). On the line card other than E3, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCFramingBitErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.44 | ||
| Number of Framing bit errors(64 bit applicable). On the line card other than DS1, E1, FR-E1, CE-DS1, FR-DS1 and CE-E1, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysFramingBitErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.45 | ||
| Number of Framing bit errors(32 bit applicable). On the line card other than DS1, E1, FR-E1, CE-DS1, FR-DS1 and CE-E1, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| perfIfPhysHCCrcErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.46 | ||
| Number of CRC errors(64 bit applicable). On the line card other than DS1, E1, FR-E1, FR-DS1, CE-DS1(ESF mode) and CE-E1, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| perfIfPhysCrcErrors | 1.3.6.1.4.1.119.2.3.14.9.5.4.1.47 | ||
| Number of CRC errors(32 bit applicable). On the line card other than DS1, E1, FR-E1, FR-DS1, CE-DS1(ESF mode) and CE-E1, the value of this object is 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| scale | 1.3.6.1.4.1.119.2.3.14.9.6 | ||
| OBJECT IDENTIFIER | |||
| scaleStatus | 1.3.6.1.4.1.119.2.3.14.9.6.1 | ||
| Order to execute and state. | |||
| OBJECT-TYPE | |||
| INTEGER | allocate(1), install(2), backup(3), free(4) | ||
| scaleCause | 1.3.6.1.4.1.119.2.3.14.9.6.2 | ||
| The result of execution. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), start(2), succeed(3), nearend(4), timeOut(5), fileNotFound(6), accessViolate(7), checksumError(8), noData(9), sbyAccessError(10) | ||
| scaleDataType | 1.3.6.1.4.1.119.2.3.14.9.6.3 | ||
| Data type. | |||
| OBJECT-TYPE | |||
| INTEGER | system(1), config(2), bill-cdr(3) | ||
| scaleTarget | 1.3.6.1.4.1.119.2.3.14.9.6.4 | ||
| IP address of the target. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| scaleFileName | 1.3.6.1.4.1.119.2.3.14.9.6.5 | ||
| File name(up to 127 characters). | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| scaleSwSide | 1.3.6.1.4.1.119.2.3.14.9.6.6 | ||
| Indicate which system of the SW-Engine. | |||
| OBJECT-TYPE | |||
| INTEGER | act(1), sby(2) | ||
| card | 1.3.6.1.4.1.119.2.3.14.9.7 | ||
| OBJECT IDENTIFIER | |||
| cardStatusTable | 1.3.6.1.4.1.119.2.3.14.9.7.1 | ||
| Table showing the configuration information of the line card with CPU. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CardStatusEntry | |||
| cardStatusEntry | 1.3.6.1.4.1.119.2.3.14.9.7.1.1 | ||
| Entry of the configuration nformation of the line card with CPU. | |||
| OBJECT-TYPE | |||
| CardStatusEntry | |||
| cardStatusServerType | 1.3.6.1.4.1.119.2.3.14.9.7.1.1.1 | ||
| Indicate the types of the server installed in the line card with CPU: other (1) ...other than the below stated types LANE (2) ARP (4) NHRP (8) MPOA (16) If more than one server type is installed, return the sum of their values. e.g. Only NHRP is installed ---> 8 ARP and NHRP are installed ---> 4 + 8 = 12 LANE, ARP and NHRP are installed ---> 2 + 4 + 8 = 14 | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| cardStatusRevision | 1.3.6.1.4.1.119.2.3.14.9.7.1.1.2 | ||
| The revision of the software installed in the line card with CPU. e.g., ...X means the number of revision. Software Version X.X(X) Boot ROM Version KXX | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| cardStatusMateSlotNumber | 1.3.6.1.4.1.119.2.3.14.9.7.1.1.3 | ||
| The slot number of the card with double configuration (including itself). If it is single configuration/although it is of double configuration, SBY system is not implemented, return zero. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..16 | ||
| cardStatusMode | 1.3.6.1.4.1.119.2.3.14.9.7.1.1.4 | ||
| Operational mode of the card. | |||
| OBJECT-TYPE | |||
| INTEGER | act(1), sby(2), single(3), other(4) | ||
| cardStatusPriority | 1.3.6.1.4.1.119.2.3.14.9.7.1.1.5 | ||
| JpnToEng(次の1行分) | |||
| OBJECT-TYPE | |||
| INTEGER | local(1), remotePrimary(2), remoteSecoundary(3) | ||
| cardStatusAtmAddr | 1.3.6.1.4.1.119.2.3.14.9.7.1.1.6 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0 | 20) | ||
| cardStatusMateAtmAddr | 1.3.6.1.4.1.119.2.3.14.9.7.1.1.7 | ||
| JpnToEng(次の2行分) | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0 | 20) | ||
| cardOpeTable | 1.3.6.1.4.1.119.2.3.14.9.7.2 | ||
| The table showing the command operations to the line card with CPU. If the card configured on SBY system is indicated, return noSuchName. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CardOpeEntry | |||
| cardOpeEntry | 1.3.6.1.4.1.119.2.3.14.9.7.2.1 | ||
| Entry of command operation to the line card with CPU. | |||
| OBJECT-TYPE | |||
| CardOpeEntry | |||
| cardOpeReset | 1.3.6.1.4.1.119.2.3.14.9.7.2.1.1 | ||
| Card Reset processing. Return noOperation(1) at read. JpnToEng[リモート二重化構成時は設定不可とし, genErrorを返却する.] | |||
| OBJECT-TYPE | |||
| INTEGER | noOperation(1), reset(2), ach(3) | ||
| cardOpeDiagnosis | 1.3.6.1.4.1.119.2.3.14.9.7.2.1.2 | ||
| Card diagnostic processing. Diagnose the SBY system card of double configuration with (the ACT system card). Return noOperation (1) at read. JpnToEng[リモート二重化構成時は設定不可とし, genErrorを返却する.] | |||
| OBJECT-TYPE | |||
| INTEGER | noOperation(1), diagnosis(2) | ||
| cardOpeSave | 1.3.6.1.4.1.119.2.3.14.9.7.2.1.3 | ||
| Card Save processing. Save the system configuration information in FROM. If it is of double configuration, save it in SBY system FROM as well. Return noOperation (1) at read. | |||
| OBJECT-TYPE | |||
| INTEGER | noOperation(1), save(2) | ||
| cardOpeSaveResult | 1.3.6.1.4.1.119.2.3.14.9.7.2.1.4 | ||
| The result of card save processing. OK /NG indicate that SAVE processing completed/failed, respectively. (NearEND) indicates that the number of writes into FROM approaches to the limit. | |||
| OBJECT-TYPE | |||
| INTEGER | succeed(1), succeed-act(2), succeed-sby(3), temporaryFailure(4), nearend(5), nearend-act(6), nearend-act-failure-sby(7), nearend-sby(8), nearend-sby-failure-act(9), notReady(10), ready(11) | ||
| cardOpeCopy | 1.3.6.1.4.1.119.2.3.14.9.7.2.1.5 | ||
| Card Copy processing. Return noOperation (1) at read. | |||
| OBJECT-TYPE | |||
| INTEGER | noOperation(1), copy-all-from-act(2), copy-all-from-sby(3), copy-config-from-act(4), copy-config-from-sby(5), copy-system-from-act(6), copy-system-from-sby(7) | ||
| cardOpeCopyResult | 1.3.6.1.4.1.119.2.3.14.9.7.2.1.6 | ||
| Result of Card Copy processing. | |||
| OBJECT-TYPE | |||
| INTEGER | succeed(1), temporaryFailure(2), nearend(3), notReady(4), ready(5) | ||
| clock | 1.3.6.1.4.1.119.2.3.14.9.8 | ||
| OBJECT IDENTIFIER | |||
| clockOpe | 1.3.6.1.4.1.119.2.3.14.9.8.1 | ||
| OBJECT IDENTIFIER | |||
| clockOpeStatus | 1.3.6.1.4.1.119.2.3.14.9.8.1.1 | ||
| Used to control Clock setting processing. | |||
| OBJECT-TYPE | |||
| INTEGER | allocate(1), set(2), free(3) | ||
| clockOpeCause | 1.3.6.1.4.1.119.2.3.14.9.8.1.2 | ||
| Result of Clock setting processing. | |||
| OBJECT-TYPE | |||
| INTEGER | noWriting(1), other(2), succeed(3), setWarning(4), parameterNotEnough(5), portNotExist(6), portOutOfRange(7), allPortFailure(8) | ||
| clockOpeMode | 1.3.6.1.4.1.119.2.3.14.9.8.1.3 | ||
| Clock Mode. | |||
| OBJECT-TYPE | |||
| INTEGER | master(1), slave(2) | ||
| clockOpeAccuracy | 1.3.6.1.4.1.119.2.3.14.9.8.1.4 | ||
| Accuracy[ppm] of clock. JpnToEng[(SLAVEモード設定時のみ有効)] If no set, value is -1. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | -1 | ||
| clockOpeSlaveLine1 | 1.3.6.1.4.1.119.2.3.14.9.8.1.5 | ||
| Slave line number 1. JpnToEng[(SLAVEモード設定時のみ有効)] If no set, value is -1. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..32 | -1 | ||
| clockOpeSlaveLine2 | 1.3.6.1.4.1.119.2.3.14.9.8.1.6 | ||
| Slave line number 2. JpnToEng[(SLAVEモード設定時のみ有効)] Slave line number 1 shall be set already. If no set, value is -1. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..32 | -1 | ||
| clockOpeSlaveLine3 | 1.3.6.1.4.1.119.2.3.14.9.8.1.7 | ||
| Slave line number 3. JpnToEng[(SLAVEモード設定時のみ有効)] Slave line number 1~2 shall be set already. If no set, value is -1. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..32 | -1 | ||
| clockOpeSlaveLine4 | 1.3.6.1.4.1.119.2.3.14.9.8.1.8 | ||
| Slave line number 4. JpnToEng[(SLAVEモード設定時のみ有効)] Slave line number 1~3 shall be set already. If no set, value is -1. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..32 | -1 | ||
| clockMode | 1.3.6.1.4.1.119.2.3.14.9.8.2 | ||
| Clock Mode. | |||
| OBJECT-TYPE | |||
| INTEGER | master(1), slave(2) | ||
| clockAccuracy | 1.3.6.1.4.1.119.2.3.14.9.8.3 | ||
| Accuracy[ppm] of clock. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | -1 | ||
| clockSlaveLine | 1.3.6.1.4.1.119.2.3.14.9.8.4 | ||
| The number of the actually slaved line. If mode is master (1), it is -1. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| clockSlaveLine1 | 1.3.6.1.4.1.119.2.3.14.9.8.5 | ||
| Slave line number 1. If no set, value is -1. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| clockSlaveLine1Status | 1.3.6.1.4.1.119.2.3.14.9.8.6 | ||
| State of slave line 1. | |||
| OBJECT-TYPE | |||
| ClockSlaveLineStatus | |||
| clockSlaveLine2 | 1.3.6.1.4.1.119.2.3.14.9.8.7 | ||
| Slave line number 2. If no set, value is -1. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| clockSlaveLine2Status | 1.3.6.1.4.1.119.2.3.14.9.8.8 | ||
| State of slave line 2. | |||
| OBJECT-TYPE | |||
| ClockSlaveLineStatus | |||
| clockSlaveLine3 | 1.3.6.1.4.1.119.2.3.14.9.8.9 | ||
| Slave line number 3. If no set, value is -1. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| clockSlaveLine3Status | 1.3.6.1.4.1.119.2.3.14.9.8.10 | ||
| State of slave line 3. | |||
| OBJECT-TYPE | |||
| ClockSlaveLineStatus | |||
| clockSlaveLine4 | 1.3.6.1.4.1.119.2.3.14.9.8.11 | ||
| Slave line number 4. If no set, value is -1. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| clockSlaveLine4Status | 1.3.6.1.4.1.119.2.3.14.9.8.12 | ||
| State of slave line 4. | |||
| OBJECT-TYPE | |||
| ClockSlaveLineStatus | |||
| diag | 1.3.6.1.4.1.119.2.3.14.9.9 | ||
| OBJECT IDENTIFIER | |||
| diagActionStatus | 1.3.6.1.4.1.119.2.3.14.9.9.1 | ||
| Used to control diagnostics test processing. | |||
| OBJECT-TYPE | |||
| INTEGER | allocate(1), start(2), execute(3), end(4), free(5) | ||
| diagActionKind | 1.3.6.1.4.1.119.2.3.14.9.9.2 | ||
| JpnToEng(次の4行分を) | |||
| OBJECT-TYPE | |||
| INTEGER | switch(1), cpu(2), slot(3) | ||
| diagPreCause | 1.3.6.1.4.1.119.2.3.14.9.9.3 | ||
| JpnToEng[診断処理実行前のパラメータチェックの結果.] | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), succeed(2), parameterNotEnough(3), notInstalled(4), notSupport(5), diagnostics(6), clkChgError(7), initializing(8), sbyAccessError(9) | ||
| diagCause | 1.3.6.1.4.1.119.2.3.14.9.9.4 | ||
| Result of diagnostics test processing. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), diagNG-SC(1020004), diagNG-BF(1030004), diagNG-ES0(1040007), diagNG-ES1(1040107), diagNG-SAR(1050005), diagNG-DI(1060010), diagNG-CPU(1070002), diagNG-CPU-Register(1600201), diagNG-CPU-Timer-Test(1600202), diagNG-CPU-MM-Test(1600203), diagNG-CPU-DRAM-Partial-Write(1600204), diagNG-CPU-Memory-Machining(1600205), diagNG-CPU-Cash-Test(1600206), diagNG-CPU-BSN-Parity(1600207), diagNG-CPU-LANCE-LoopBack(1600208), diagNG-Local-Memory(1600301), diagNG-DMAC-Register(1600302), diagNG-MISCEMA-Register(1600303), diagNG-XACK-Interrupt(1600304), diagNG-ASW-Register(1600401), diagNG-BMT(1600402), diagNG-Failer-Detect(1600403), diagNG-SAR-Register(1600501), diagNG-SAR-Control-Memory(1600502), diagNG-SAR-Packet-Memory(1600503), diagNG-DI-Register(1600504), diagNG-DI-Memory(1600505), diagNG-ES-LoopBack(1600601), diagNG-ES-Own-LoopBack(1600602), diagNG-ES-Other-LoopBack(1600603), diagNG-ES-Own-Broadcast-LoopBack(1600604), diagNG-ES-Other-Broadcast-LoopBack(1600605), diagNG-ES-Nto1-Test(1600606), diagNG-ATOM-Buffer-OVF(1600607), diagNG-BackPressure(1600608), diagNG-RICEtoCell-Compete(1600609), diagNG-SAR-LoopBack(1600701), diagNG-DI-LoopBack(1600702), diagNG-SW-Own-LoopBack(1600703), diagNG-SW-Other-LoopBack(1600704), diagNG-Illegal-Cell-Detect(1600705), diagNG-SARtoPacket-Compete(1600706), diagNG-PCMCIA-Register(1601101), diagNG-IXB-Register(2010002), diagNG-OXB-Register(2020003), diagNG-UHT-Register(2030003), diagNG-IBC-Register(2040008), diagNG-IBC-RIRO-SGRAM(2040009), diagNG-IBC-HT-i-SGRAM(2040010), diagNG-IBC-RIRO-SRAM(2040011), diagNG-OBC-Register(2040012), diagNG-OBC-CellBuffer(2040013), diagNG-OBC-HT-o(2040014), diagNG-OBC-BCI-BMT(2040015), diagNG-FR-SDRAM(2090006), diagNG-PHY0(3010002), diagNG-PHY1(3010102), diagNG-PHY2(3010202), diagNG-PHY3(3010302), diagNG-MUX(3020012), diagNG-CU2INF(3030002), diagNG-UNIC(3040003), diagNG-CFAD(3050003), diagNG-PLD(3060003), diagNG-FPGA(3070004), diagNG-FRM0(3080004), diagNG-FRM1(3080104), diagNG-S-UNI622(3120004), diagNG-TAC0(3130001), diagNG-TAC1(3130101), diagNG-TAC2(3130201), diagNG-TAC3(3130301), diagNG-LCA-Common(3150001), diagNG-LCA-Separate(3150002), diagNG-UCFAD2(3160001), diagNG-PM7345-0(3140005), diagNG-PM7345-1(3140105), diagNG-PM7345-2(3140205), diagNG-PM7345-3(3140305), diagNG-PM4341A-0(3170001), diagNG-PM4341A-1(3170101), diagNG-PM4341A-2(3170201), diagNG-PM4341A-3(3170301), diagNG-PM6341-0(3180001), diagNG-PM6341-1(3180101), diagNG-PM6341-2(3180201), diagNG-PM6341-3(3180301), diagNG-DCS-LCA(3230003), diagNG-ALARM(3190001), diagNG-FRAME(3190002), diagNG-TS-CTL(3190003), diagNG-FIFO-CTL(3190004), diagNG-AAL1-SAR(3200001), diagNG-FPGA-CE-DS1(3210003), diagNG-FPGA-CE-E1(3220004), diagNG-WAC-021(3240001), diagNG-CPU-DRAM(3250001), diagNG-CPU-Tout(3250002) | ||
| diagParam1 | 1.3.6.1.4.1.119.2.3.14.9.9.5 | ||
| JpnToEng[次の2行分] | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| pnni | 1.3.6.1.4.1.119.2.3.14.9.10 | ||
| OBJECT IDENTIFIER | |||
| pnniNode | 1.3.6.1.4.1.119.2.3.14.9.10.1 | ||
| OBJECT IDENTIFIER | |||
| pnniNodeOpe | 1.3.6.1.4.1.119.2.3.14.9.10.1.1 | ||
| OBJECT IDENTIFIER | |||
| pnniNodeTable | 1.3.6.1.4.1.119.2.3.14.9.10.1.2 | ||
| Table of PNNI Logical node attributes. A row exist every PNNI peer group which the managed system belongs to. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PnniNodeEntry | |||
| pnniNodeEntry | 1.3.6.1.4.1.119.2.3.14.9.10.1.2.1 | ||
| Entry of pnniNodeTable. | |||
| OBJECT-TYPE | |||
| PnniNodeEntry | |||
| pnniNodeLevel | 1.3.6.1.4.1.119.2.3.14.9.10.1.2.1.1 | ||
| PNNI hierarchy level where node(s) reside. | |||
| OBJECT-TYPE | |||
| PnniLevel | |||
| pnniNodeId | 1.3.6.1.4.1.119.2.3.14.9.10.1.2.1.2 | ||
| Node ID. | |||
| OBJECT-TYPE | |||
| PnniNodeId | |||
| pnniNodeAtmAddress | 1.3.6.1.4.1.119.2.3.14.9.10.1.2.1.3 | ||
| ATM End System Address of node. | |||
| OBJECT-TYPE | |||
| PnniAtmAddr | |||
| pnniNodePeerGroupId | 1.3.6.1.4.1.119.2.3.14.9.10.1.2.1.4 | ||
| Peer Group Identifier of the peer group which a node belongs to. | |||
| OBJECT-TYPE | |||
| PnniPeerGroupId | |||
| pnniNodeRestrictedTransit | 1.3.6.1.4.1.119.2.3.14.9.10.1.2.1.5 | ||
| Restrict a node to be used as a transit route. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| pnniNodeRestrictedBranching | 1.3.6.1.4.1.119.2.3.14.9.10.1.2.1.6 | ||
| Restrict a node to be used as a branch point of point-to-multipoint. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| pnniNodeLeadershipPriority | 1.3.6.1.4.1.119.2.3.14.9.10.1.2.1.7 | ||
| Leadership priority which a node notifies of. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..255 | ||
| matCmd | 1.3.6.1.4.1.119.2.3.14.9.11 | ||
| OBJECT IDENTIFIER | |||
| matCmdStatus | 1.3.6.1.4.1.119.2.3.14.9.11.1 | ||
| JpnToEng(次の5行分) | |||
| OBJECT-TYPE | |||
| INTEGER | allocate(1), inActive(2), active(3), free(4) | ||
| matCmdInput | 1.3.6.1.4.1.119.2.3.14.9.11.2 | ||
| JpnToEng(次の1行分) | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| matCmdOutput | 1.3.6.1.4.1.119.2.3.14.9.11.3 | ||
| JpnToEng(次の1行分) | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| matCmdOutputType | 1.3.6.1.4.1.119.2.3.14.9.11.4 | ||
| JpnToEng(次の4行分) | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), continued(2), interactive(3) | ||
| matCmdStop | 1.3.6.1.4.1.119.2.3.14.9.11.5 | ||
| When the value is set to 'stop', the MAT command is stopped. When the value is set to 'noOperation', no operation is performed. When read, the value 'noOperation' is returned. | |||
| OBJECT-TYPE | |||
| INTEGER | noOperation(1), stop(2) | ||
| matCmdTimeOut | 1.3.6.1.4.1.119.2.3.14.9.11.6 | ||
| JpnToEng(次の1行分) | |||
| OBJECT-TYPE | |||
| INTEGER | 1..180 | ||
| m7-corporate-mib | 1.3.6.1.4.1.119.2.3.14.12 | ||
| OBJECT IDENTIFIER | |||
| NodeStatusEntry | |||
| SEQUENCE | |||
| INTEGER as nodeStatusIndex | |||
| INTEGER as nodeStatusPower | |||
| INTEGER as nodeStatusSwitchMode | |||
| INTEGER as nodeStatusSwitch | |||
| NodePCMCIAEntry | |||
| SEQUENCE | |||
| INTEGER as nodePCMCIAIndex | |||
| INTEGER as nodePCMCIAStatus | |||
| INTEGER as nodePCMCIAType | |||
| SlotIfConfEntry | |||
| SEQUENCE | |||
| INTEGER as slotIfConfIndex | |||
| INTEGER as slotIfConfPhysType | |||
| DisplayString as slotIfConfRev | |||
| INTEGER as slotIfConfStatus | |||
| INTEGER as slotIfConfBufferType | |||
| DisplayString as slotIfConfBufferRev | |||
| INTEGER as slotIfConfReset | |||
| INTEGER as slotIfConfResetResult | |||
| LinfFilterMaskVpi | |||
| INTEGER | -1 | 0..12 | ||
| LinfFilterMaskVci | |||
| INTEGER | -1 | 0..14 | ||
| LinfCellMappingMode | |||
| INTEGER | direct(1), plcp(2) | ||
| LinfScramble | |||
| INTEGER | on(1), off(2) | ||
| LinfLBO | |||
| INTEGER | low(1), hi(2), length-0-110(3), length-110-220(4), length-220-330(5), length-330-440(6), length-440-550(7), length-550-660(8), length-over660(9) | ||
| LinfFrameMode | |||
| INTEGER | c-bit(1), m23(2), g832-g804(3), g751(4), m13(5), esf(6), sf(7) | ||
| LinfMinVci | |||
| INTEGER | 0..16383 | ||
| LinfMaxVci | |||
| INTEGER | 0..16383 | ||
| LinfService | |||
| INTEGER | unstructured(1), structured(2) | ||
| LinfInterWorking | |||
| INTEGER | network(1), service(2) | ||
| LinfVendor | |||
| INTEGER | notApplicable(1), stratacom(2), digital-equipment(3), northan-telecom(4), cisco-systems(5) | ||
| LinfFractionalType | |||
| INTEGER | unstructured(1), fractional(2) | ||
| LinfFractionalSet | |||
| INTEGER | |||
| LinfCasMode | |||
| INTEGER | notApplicable(1), basic(2), cas(3) | ||
| LinfCodingMode | |||
| INTEGER | hdb3(1), ami(2) | ||
| LinfUnUsedParam | |||
| INTEGER | unused(-1) | ||
| LinfStatusEntry | |||
| SEQUENCE | |||
| INTEGER as linfIndex | |||
| INTEGER as linfStatus | |||
| INTEGER as linfLoopBack | |||
| INTEGER as linfConf | |||
| INTEGER as linfFwdAvailableBandWidth | |||
| INTEGER as linfBkwdAvailableBandWidth | |||
| INTEGER as linfJ2Rate | |||
| INTEGER as linfCacFactor | |||
| INTEGER as linfLoopBackCause | |||
| INTEGER as linfBandWidth | |||
| INTEGER as linfRecommendation | |||
| INTEGER as linfUnassignedIdle | |||
| INTEGER as linfMaxActiveVpiBits | |||
| INTEGER as linfMaxActiveVciBits | |||
| INTEGER as linfPhysType | |||
| INTEGER as linfParam1 | |||
| INTEGER as linfParam2 | |||
| INTEGER as linfParam3 | |||
| INTEGER as linfParam4 | |||
| INTEGER as linfParam5 | |||
| INTEGER as linfParam6 | |||
| INTEGER as linfParam7 | |||
| LinfFifoConfEntry | |||
| SEQUENCE | |||
| INTEGER as linfFifoConfifIndex | |||
| INTEGER as linfFifoConfIndex | |||
| INTEGER as linfFifoConfStatus | |||
| INTEGER as linfFifoConfPeekRate | |||
| INTEGER as linfFifoConfSustainRate | |||
| INTEGER as linfFifoConfMaxBurstSize | |||
| INTEGER as linfFifoConfRowStatus | |||
| ConnPvcEntry | |||
| SEQUENCE | |||
| INTEGER as connPvcPort | |||
| INTEGER as connPvcVpi | |||
| INTEGER as connPvcVci | |||
| INTEGER as connPvcDirection | |||
| INTEGER as connPvcIndex | |||
| INTEGER as connPvcContrastPort | |||
| INTEGER as connPvcContrastVpi | |||
| INTEGER as connPvcContrastVci | |||
| INTEGER as connPvcTopology | |||
| INTEGER as connPvcTrafficType | |||
| INTEGER as connPvcFifoIndex | |||
| INTEGER as connPvcContrastFifoIndex | |||
| INTEGER as connPvcTrfConf | |||
| INTEGER as connPvcTrfResult | |||
| INTEGER as connPvcParam1 | |||
| INTEGER as connPvcContrastParam1 | |||
| DisplayString as connPvcParam2 | |||
| DisplayString as connPvcContrastParam2 | |||
| INTEGER as connPvcParam3 | |||
| INTEGER as connPvcContrastParam3 | |||
| INTEGER as connPvcParam4 | |||
| INTEGER as connPvcContrastParam4 | |||
| INTEGER as connPvcParam5 | |||
| INTEGER as connPvcContrastParam5 | |||
| INTEGER as connPvcParam6 | |||
| INTEGER as connPvcContrastParam6 | |||
| INTEGER as connPvcParam7 | |||
| INTEGER as connPvcContrastParam7 | |||
| ConnPvcTrfEntry | |||
| SEQUENCE | |||
| OCTET STRING as connPvcTrfInCells | |||
| Counter as connPvcTrfInCellsCounters | |||
| OCTET STRING as connPvcTrfOutCells | |||
| Counter as connPvcTrfOutCellsCounters | |||
| OCTET STRING as connPvcTrfInDropCells | |||
| Counter as connPvcTrfInDropCellsCounters | |||
| ConnConfIfEntry | |||
| SEQUENCE | |||
| INTEGER as connConfIfPvcs | |||
| INTEGER as connConfIfSvcs | |||
| INTEGER as connConfIfSoftPvcs | |||
| DstAtmAddressFormat | |||
| INTEGER | noWriting(-1), e-164(1), nsap(2) | ||
| DstAtmAddressLength | |||
| INTEGER | 4..160 | -1 | ||
| DstAtmAddress | |||
| OCTET STRING | SIZE(0..20) | ||
| DstPrimaryIfIndex | |||
| INTEGER | 1..99 | -1 | ||
| DstPrimaryVPI | |||
| INTEGER | 0..4095 | -1 | ||
| DstSecondaryIfIndex | |||
| INTEGER | 1..99 | -1 | ||
| DstSecondaryVPI | |||
| INTEGER | 0..4095 | -1 | ||
| ConnRouteOpeFailureCause | |||
| INTEGER | noWriting(-1), other(1), allocateSucceed(2), tableIsFull(3), parameterIsNotEnough(4), specifiedAddressIsIllegal(5), specifiedAddressIsAlreadyExisting(6), specifiedAddressIsNotExisting(7) | ||
| ConnRouteEntry | |||
| SEQUENCE | |||
| INTEGER as connRouteType | |||
| INTEGER as connRoutePrimaryIfIndex | |||
| INTEGER as connRoutePrimaryVPI | |||
| INTEGER as connRouteSecondaryIfIndex | |||
| INTEGER as connRouteSecondaryVPI | |||
| INTEGER as connRouteTertiaryIfIndex | |||
| INTEGER as connRouteTertiaryVPI | |||
| INTEGER as connRouteFourthryIfIndex | |||
| INTEGER as connRouteFourthryVPI | |||
| INTEGER as connRouteFifthryIfIndex | |||
| INTEGER as connRouteFifthryVPI | |||
| INTEGER as connRouteSixthryIfIndex | |||
| INTEGER as connRouteSixthryVPI | |||
| INTEGER as connRouteSeventhryIfIndex | |||
| INTEGER as connRouteSeventhryVPI | |||
| INTEGER as connRoutePrimaryStatus | |||
| INTEGER as connRoutePrimaryCause | |||
| DstAtmAddressFormat as connRouteAtmAddressFormat | |||
| DstAtmAddressLength as connRouteAtmAddressLength | |||
| DstAtmAddress as connRouteAtmAddress | |||
| ConnSoftPvcEntry | |||
| SEQUENCE | |||
| INTEGER as connSoftPvcIndex | |||
| INTEGER as connSoftPvcTopology | |||
| INTEGER as connSoftPvcTrafficType | |||
| INTEGER as connSoftPvcEndpointType | |||
| INTEGER as connSoftPvcRetry | |||
| INTEGER as connSoftPvcSrcAtmAddressFormat | |||
| INTEGER as connSoftPvcSrcAtmAddressLength | |||
| OCTET STRING as connSoftPvcSrcAtmAddress | |||
| INTEGER as connSoftPvcSrcIfIndex | |||
| INTEGER as connSoftPvcSrcVPI | |||
| INTEGER as connSoftPvcSrcVCI | |||
| INTEGER as connSoftPvcDstAtmAddressFormat | |||
| INTEGER as connSoftPvcDstAtmAddressLength | |||
| OCTET STRING as connSoftPvcDstAtmAddress | |||
| INTEGER as connSoftPvcDstIfIndex | |||
| INTEGER as connSoftPvcDstVPI | |||
| INTEGER as connSoftPvcDstVCI | |||
| INTEGER as connSoftPvcRowStatus | |||
| INTEGER as connSoftPvcCause | |||
| INTEGER as connSoftPvcRestRetry | |||
| INTEGER as connSoftPvcSrcFifoIndex | |||
| INTEGER as connSoftPvcDstFifoIndex | |||
| INTEGER as connSoftPvcNodeKind | |||
| INTEGER as connSoftPvcSrcParam1 | |||
| INTEGER as connSoftPvcDstParam1 | |||
| DisplayString as connSoftPvcSrcParam2 | |||
| DisplayString as connSoftPvcDstParam2 | |||
| INTEGER as connSoftPvcSrcParam3 | |||
| INTEGER as connSoftPvcDstParam3 | |||
| INTEGER as connSoftPvcSrcParam4 | |||
| INTEGER as connSoftPvcDstParam4 | |||
| INTEGER as connSoftPvcSrcParam5 | |||
| INTEGER as connSoftPvcDstParam5 | |||
| INTEGER as connSoftPvcSrcParam6 | |||
| INTEGER as connSoftPvcDstParam6 | |||
| INTEGER as connSoftPvcSrcParam7 | |||
| INTEGER as connSoftPvcDstParam7 | |||
| ConnSoftPvcSrcAtmAddressFormat | |||
| INTEGER | noWriting(-1), e-164(1), nsap(2) | ||
| ConnSoftPvcDstAtmAddressFormat | |||
| INTEGER | noWriting(-1), e-164(1), nsap(2) | ||
| ConnSoftPvcEstSrcInfIndex | |||
| INTEGER | 1..128 | ||
| ConnSoftPvcEstablishedSrcInfEntry | |||
| SEQUENCE | |||
| Opaque as connSoftPvcEstablishedSrcInf | |||
| ConnSoftPvcEstSrcInfIndex as connSoftPvcEstSrcInfIndex | |||
| ConnOamEntry | |||
| SEQUENCE | |||
| INTEGER as connOamPort | |||
| INTEGER as connOamIndex | |||
| INTEGER as connOamContrastPort | |||
| INTEGER as connOamVpi | |||
| INTEGER as connOamContrastVpi | |||
| INTEGER as connOamVci | |||
| INTEGER as connOamContrastVci | |||
| INTEGER as connOamPoint | |||
| INTEGER as connOamMode | |||
| INTEGER as connOamSection | |||
| INTEGER as connOamStatus | |||
| INTEGER as connOamDefectType | |||
| OCTET STRING as connOamDefectNodeID | |||
| ConnProfileIndex | |||
| INTEGER | |||
| ConnProfileEntry | |||
| SEQUENCE | |||
| ConnProfileIndex as connProfileIndex | |||
| INTEGER as connProfileRowStatus | |||
| INTEGER as connProfileCause | |||
| INTEGER as connProfileTrafficType | |||
| DisplayString as connProfileName | |||
| INTEGER as connProfileParam1 | |||
| INTEGER as connProfileParam2 | |||
| INTEGER as connProfileParam3 | |||
| INTEGER as connProfileParam4 | |||
| ConnSvcEntry | |||
| SEQUENCE | |||
| INTEGER as connSvcIndex | |||
| Opaque as connSvcInf | |||
| ConnCeVcEntry | |||
| SEQUENCE | |||
| INTEGER as connCeVcPort | |||
| INTEGER as connCeVcVci | |||
| INTEGER as connCeVcRowStatus | |||
| INTEGER as connCeVcCause | |||
| INTEGER as connCeVcDirection | |||
| INTEGER as connCeVcUpPartialFillSize | |||
| INTEGER as connCeVcDownPartialFillSize | |||
| INTEGER as connCeVcCondition | |||
| INTEGER as connCeVcCDVT | |||
| INTEGER as connCeVcUpPCR | |||
| INTEGER as connCeVcDownPCR | |||
| INTEGER as connCeVcUpTimeSlot1 | |||
| INTEGER as connCeVcDownTimeSlot1 | |||
| INTEGER as connCeVcUpTimeSlot2 | |||
| INTEGER as connCeVcDownTimeSlot2 | |||
| INTEGER as connCeVcUpTimeSlot3 | |||
| INTEGER as connCeVcDownTimeSlot3 | |||
| ConnFrDlciEntry | |||
| SEQUENCE | |||
| INTEGER as connFrDlciPort | |||
| INTEGER as connFrDlciIndex | |||
| INTEGER as connFrDlciRowStatus | |||
| INTEGER as connFrDlciCause | |||
| DisplayString as connFrDlciFrProfile | |||
| INTEGER as connFrDlciPCR | |||
| INTEGER as connFrDlciSCR | |||
| INTEGER as connFrDlciMBS | |||
| ConnFrProfileIndex | |||
| INTEGER | |||
| ConnFrProfileEntry | |||
| SEQUENCE | |||
| ConnFrProfileIndex as connFrProfileIndex | |||
| INTEGER as connFrProfileRowStatus | |||
| INTEGER as connFrProfileCause | |||
| DisplayString as connFrProfileName | |||
| INTEGER as connFrProfileInterworkingType | |||
| INTEGER as connFrProfileCIR | |||
| INTEGER as connFrProfileDEtoCLP | |||
| INTEGER as connFrProfileCLPValue | |||
| INTEGER as connFrProfileCLPtoDE | |||
| INTEGER as connFrProfileDEValue | |||
| INTEGER as connFrProfileCapsulationMode | |||
| INTEGER as connFrProfileCongestionMode | |||
| PerfIfEntry | |||
| SEQUENCE | |||
| INTEGER as perfIfIndex | |||
| OCTET STRING as perfIfReceivedCells | |||
| Counter as perfIfReceivedCellsCounters | |||
| OCTET STRING as perfIfTransmittedCells | |||
| Counter as perfIfTransmittedCellsCounters | |||
| OCTET STRING as perfIfMisDelivdCells | |||
| Counter as perfIfMisDelivdCellsCounters | |||
| OCTET STRING as perfIfThresholdExcessCells | |||
| Counter as perfIfThresholdExcessCellsCounters | |||
| OCTET STRING as perfIfUpcErrorCells | |||
| Counter as perfIfUpcErrorCellsCounters | |||
| PerfIfSlotEntry | |||
| SEQUENCE | |||
| OCTET STRING as perfIfSlotReceivedCells | |||
| OCTET STRING as perfIfSlotTransmittedCells | |||
| OCTET STRING as perfIfSlotInDropCells | |||
| Counter as perfIfSlotReceivedCellsCounters | |||
| Counter as perfIfSlotTransmittedCellsCounters | |||
| Counter as perfIfSlotInDropCellsCounters | |||
| OCTET STRING as perfIfSlotHCThresholdExcessCells | |||
| Counter as perfIfSlotThresholdExcessCells | |||
| OCTET STRING as perfIfSlotHCUpcErrorCells | |||
| Counter as perfIfSlotUpcErrorCells | |||
| PerfIfPhysEntry | |||
| SEQUENCE | |||
| INTEGER as perfIfPhysPort | |||
| OCTET STRING as perfIfPhysHCHecErorrs | |||
| INTEGER as perfIfPhysHecErorrs | |||
| OCTET STRING as perfIfPhysHCHecDropCells | |||
| INTEGER as perfIfPhysHecDropCells | |||
| OCTET STRING as perfIfPhysHCB1Errors | |||
| INTEGER as perfIfPhysB1Errors | |||
| OCTET STRING as perfIfPhysHCB2Errors | |||
| INTEGER as perfIfPhysB2Errors | |||
| OCTET STRING as perfIfPhysHCB3Errors | |||
| INTEGER as perfIfPhysHCB3Errors | |||
| OCTET STRING as perfIfPhysHCPathFEBEs | |||
| INTEGER as perfIfPhysPathFEBEs | |||
| OCTET STRING as perfIfPhysHCLineFEBEs | |||
| INTEGER as perfIfPhysLineFEBEs | |||
| OCTET STRING as perfIfPhysHCFramingErrors | |||
| INTEGER as perfIfPhysFramingErrors | |||
| OCTET STRING as perfIfPhysHCReceivedCells | |||
| INTEGER as perfIfPhysReceivedCells | |||
| OCTET STRING as perfIfPhysHCTransmittedCells | |||
| INTEGER as perfIfPhysTransmittedCells | |||
| OCTET STRING as perfIfPhysHCIdelUnassignedCells | |||
| INTEGER as perfIfPhysIdelUnassignedCells | |||
| OCTET STRING as perfIfPhysHCFEBEErrors | |||
| INTEGER as perfIfPhysFEBEErrors | |||
| OCTET STRING as perfIfPhysHCFEBEs | |||
| INTEGER as perfIfPhysFEBEs | |||
| OCTET STRING as perfIfPhysHCPathParityErrors | |||
| INTEGER as perfIfPhysPathParityErrors | |||
| OCTET STRING as perfIfPhysHCParityErrors | |||
| INTEGER as perfIfPhysParityErrors | |||
| OCTET STRING as perfIfPhysHCSEZs | |||
| INTEGER as perfIfPhysSEZs | |||
| OCTET STRING as perfIfPhysHCBitErrors | |||
| INTEGER as perfIfPhysBitErrors | |||
| OCTET STRING as perfIfPhysHCLcvErrors | |||
| INTEGER as perfIfPhysLcvErrors | |||
| OCTET STRING as perfIfPhysHCBip8Errors | |||
| INTEGER as perfIfPhysBip8Errors | |||
| OCTET STRING as perfIfPhysHCIecErrors | |||
| INTEGER as perfIfPhysIecErrors | |||
| OCTET STRING as perfIfPhysHCFramingPatternErrors | |||
| INTEGER as perfIfPhysFramingPatternErrors | |||
| OCTET STRING as perfIfPhysHCFramingBitErrors | |||
| INTEGER as perfIfPhysFramingBitErrors | |||
| OCTET STRING as perfIfPhysHCCrcErrors | |||
| INTEGER as perfIfPhysCrcErrors | |||
| CardStatusEntry | |||
| SEQUENCE | |||
| INTEGER as cardStatusServerType | |||
| DisplayString as cardStatusRevision | |||
| INTEGER as cardStatusMateSlotNumber | |||
| INTEGER as cardStatusMode | |||
| INTEGER as cardStatusPriority | |||
| OCTET STRING as cardStatusAtmAddr | |||
| OCTET STRING as cardStatusMateAtmAddr | |||
| CardOpeEntry | |||
| SEQUENCE | |||
| INTEGER as cardOpeReset | |||
| INTEGER as cardOpeDiagnosis | |||
| INTEGER as cardOpeSave | |||
| INTEGER as cardOpeSaveResult | |||
| INTEGER as cardOpeCopy | |||
| INTEGER as cardOpeCopyResult | |||
| ClockSlaveLineStatus | |||
| INTEGER | notApplicable(1), active(2), standby(3), hardError(4), adminDown(5), notExist(6), linfDown(7), testing(8), notSupported(9), syncronizedFailure(10), lossOf64kClock(11), lossOf8kClock(12), frequencyOutOfRange(13) | ||
| PnniAtmAddr | |||
| OCTET STRING | SIZE(20) | ||
| PnniNodeId | |||
| OCTET STRING | SIZE(22) | ||
| PnniPeerGroupId | |||
| OCTET STRING | SIZE(14) | ||
| PnniLevel | |||
| INTEGER | 0..104 | ||
| PnniNodeEntry | |||
| SEQUENCE | |||
| PnniLevel as pnniNodeLevel | |||
| PnniNodeId as pnniNodeId | |||
| PnniAtmAddr as pnniNodeAtmAddress | |||
| PnniPeerGroupId as pnniNodePeerGroupId | |||
| TruthValue as pnniNodeRestrictedTransit | |||
| TruthValue as pnniNodeRestrictedBranching | |||
| INTEGER as pnniNodeLeadershipPriority | |||