NETLINK-SPECIFIC-MIB

File: NETLINK-SPECIFIC-MIB.mib (345850 bytes)

Imported modules

RFC-1212 SNMPv2-TC RFC1213-MIB
RFC1155-SMI

Imported symbols

OBJECT-TYPE RowStatus MacAddress
TimeInterval mib-2 enterprises
mgmt TimeTicks Gauge
Counter IpAddress NetworkAddress

Defined Objects

snaDLC 1.3.6.1.2.1.41
OBJECT IDENTIFIER    

sdlc 1.3.6.1.2.1.41.1
OBJECT IDENTIFIER    

sdlcLSGroup 1.3.6.1.2.1.41.1.2
OBJECT IDENTIFIER    

sdlcLSAdminTable 1.3.6.1.2.1.41.1.2.1
OBJECT IDENTIFIER    

sdlcLSAdminEntry 1.3.6.1.2.1.41.1.2.1.1
OBJECT IDENTIFIER    

sdlcLSAddress 1.3.6.1.2.1.41.1.2.1.1.1
This value is the poll address of the secondary link station for this SDLC link. It uniquely identifies the SDLC link station within a single SDLC port.
OBJECT-TYPE    
  INTEGER 1..255  


network 1.3.6.1.4.1.173.6
OBJECT IDENTIFIER    

netstat 1.3.6.1.4.1.173.6.1
OBJECT IDENTIFIER    

nsMaxNeigh 1.3.6.1.4.1.173.6.1.1
Maximum number of neighbor nodes. This value is currently always 64 for FRX8000 and 20 for an N7400 or 7500. A neighbor is the closest node in a path from the local node.
OBJECT-TYPE    
  INTEGER  

nsThisNode 1.3.6.1.4.1.173.6.1.2
This nodes number. (1-250)
OBJECT-TYPE    
  INTEGER  

nsNodTable 1.3.6.1.4.1.173.6.1.3
A table showing all nodes known to this node along with status and neighbor information.
OBJECT-TYPE    
  SEQUENCE OF  
    NsEntry

nsEntry 1.3.6.1.4.1.173.6.1.3.1
Each entry of the node table is indexed by node number.
OBJECT-TYPE    
  NsEntry  

nsNodNum 1.3.6.1.4.1.173.6.1.3.1.1
The node number of the desired node. This is the index into the node table.
OBJECT-TYPE    
  INTEGER  

nsStatus 1.3.6.1.4.1.173.6.1.3.1.2
The operational status of the node. The status is given as: 1 = Node is defined in the database; 9 = Node is operational;
OBJECT-TYPE    
  INTEGER  

nsNumNeigh 1.3.6.1.4.1.173.6.1.3.1.3
Current number of neighbor nodes to this node.
OBJECT-TYPE    
  INTEGER  

nsNeighTable 1.3.6.1.4.1.173.6.1.4
The neighbor table lists the status of a nodes neighbors.
OBJECT-TYPE    
  SEQUENCE OF  
    NsNeighEntry

nsNeighEntry 1.3.6.1.4.1.173.6.1.4.1
The table entries are indexed by the node number and the neighbors node number.
OBJECT-TYPE    
  NsNeighEntry  

nsNTNode 1.3.6.1.4.1.173.6.1.4.1.1
The node number of the node whose neighbor's status is being sought.
OBJECT-TYPE    
  INTEGER  

nsNTNeigh 1.3.6.1.4.1.173.6.1.4.1.2
The node number of the neighbor whose status is being sought.
OBJECT-TYPE    
  INTEGER  

nsNTNeighStat 1.3.6.1.4.1.173.6.1.4.1.3
The status of the neighbor node given as: 1 = previously, but not currently, connected; 2 = Currently connected;
OBJECT-TYPE    
  INTEGER notConnected(1), connected(2)  

local 1.3.6.1.4.1.173.7
OBJECT IDENTIFIER    

node 1.3.6.1.4.1.173.7.1
OBJECT IDENTIFIER    

nodeCfgTable 1.3.6.1.4.1.173.7.1.1
OBJECT IDENTIFIER    

nodeAlmTable 1.3.6.1.4.1.173.7.1.2
OBJECT IDENTIFIER    

nodeSNMPGroup 1.3.6.1.4.1.173.7.1.3
OBJECT IDENTIFIER    

nodeModel 1.3.6.1.4.1.173.7.1.3.1
Describes the unit model
OBJECT-TYPE    
  INTEGER model1(1), model2(2), rackmount(3), highavail(4), netfrad(5), frx4000(6), ss1800(7)  

nodeTrapText 1.3.6.1.4.1.173.7.1.3.2
Text of the last alarm generated
OBJECT-TYPE    
  DisplayString  

nodeTrapAdrTable 1.3.6.1.4.1.173.7.1.3.3
A table used to define the IP address of end-nodes to receive alarms generated by this node. Up to 16 addresses can be specified.
OBJECT-TYPE    
  SEQUENCE OF  
    TpAdrEntry

tpAdrEntry 1.3.6.1.4.1.173.7.1.3.3.1
A Trap entry containing objects relating to SNMP traps.
OBJECT-TYPE    
  TpAdrEntry  

tpAdrIdx 1.3.6.1.4.1.173.7.1.3.3.1.1
The index into the trap configuration table
OBJECT-TYPE    
  INTEGER  

tpAddress 1.3.6.1.4.1.173.7.1.3.3.1.2
The IP Address of the end-station to send alarms
OBJECT-TYPE    
  IpAddress  

tpAdrFlag 1.3.6.1.4.1.173.7.1.3.3.1.3
Defines the state of this entry as: 0 = Do not send traps to the Address; 1 = Send traps to the Address; 2 = This Address entry is deleted from the table;
OBJECT-TYPE    
  INTEGER disableTraps(1), enableTraps(2), delete(3)  

tpAdrSLev 1.3.6.1.4.1.173.7.1.3.3.1.4
Lowest severity level traps that will be sent to this Address; 1 is the highest, 4 is the lowest.
OBJECT-TYPE    
  INTEGER critical(1), major(2), minor(3), informational(4)  

nodeBagTable 1.3.6.1.4.1.173.7.1.4
OBJECT IDENTIFIER    

hwcard 1.3.6.1.4.1.173.7.2
OBJECT IDENTIFIER    

rlpMaxProtos 1.3.6.1.4.1.173.7.2.1
Maximum number of protocols allowed on each RLP. This value is currently 11 for FRX4000s, 9 for FRX6000s, and 5 for FRX7000s and FRX8000s.
OBJECT-TYPE    
  INTEGER  

rlpConfigTable 1.3.6.1.4.1.173.7.2.2
A Table to describe each RLP on the node
OBJECT-TYPE    
  SEQUENCE OF  
    RlpEntry

rlpEntry 1.3.6.1.4.1.173.7.2.2.1
An RLP entry containing objects relating to RLPs.
OBJECT-TYPE    
  RlpEntry  

rlpIndex 1.3.6.1.4.1.173.7.2.2.1.1
The RLP number on the node
OBJECT-TYPE    
  INTEGER  

rlpStatus 1.3.6.1.4.1.173.7.2.2.1.2
The current state of this RLP
OBJECT-TYPE    
  INTEGER installed(1), configured(2), load-failed(3), loading(4), ipl-failed(5), ipl-in-progress(6), failed(7), operational(8), power-off(9), power-on(10)  

rlpMemorySize 1.3.6.1.4.1.173.7.2.2.1.3
The amount of memory installed on this RLP
OBJECT-TYPE    
  INTEGER  

rlpLIC1Type 1.3.6.1.4.1.173.7.2.2.1.4
The Type of Line Interface card in the first position
OBJECT-TYPE    
  INTEGER none(1), rs232(2), rs422(3), v35(4), hs-rs232(5), x21(6), rs449(7), universal(8), t1(10), e1(11), voice(13)  

rlpLIC2Type 1.3.6.1.4.1.173.7.2.2.1.5
The Type of Line Interface card in the second position
OBJECT-TYPE    
  INTEGER none(1), rs232(2), rs422(3), v35(4), hs-rs232(5), x21(6), rs449(7), universal(8), t1(10), e1(11), voice(13)  

rlpProtocol 1.3.6.1.4.1.173.7.2.2.1.6
The protocols configured on this RLP. This is an OCTET STRING where each octet represents a protocol type. The size of this is the maximum number of protocols allowed on an RLP (rlpMaxProtos). The protocol types are defined as: 00 = none 01 = X.25 02 = Frame Relay 03 = Async 04 = SDLC 05 = BSC Interactive 07 = IP 08 = SNMP 09 = RIP 0A = LLC2 0B = Trunk 0C = IPX 0D = Config 0E = LLC2-R 0F = IP-R 10 = NVSP 11 = Bridge
OBJECT-TYPE    
  OCTET STRING  

rlpGroupNumber 1.3.6.1.4.1.173.7.2.2.1.7
The group to which this RLP belongs- always 1 if not FRX7000.
OBJECT-TYPE    
  INTEGER 1..4  

rlpGroupResponsibility 1.3.6.1.4.1.173.7.2.2.1.8
The responsibility of this RLP within its group, always primary if not FRX7000.
OBJECT-TYPE    
  INTEGER primary(1), secondary(2)  

port 1.3.6.1.4.1.173.7.3
OBJECT IDENTIFIER    

portX25Group 1.3.6.1.4.1.173.7.3.1
OBJECT IDENTIFIER    

portPhyX25AdminTable 1.3.6.1.4.1.173.7.3.1.1
This table contains Netlink Enterprise specific objects to manage an X25 port. Changing one of these parameters may take effect in the operating port immediately or may wait until the interface is restarted depending on the details of the implementation. Most of the objects in this read-write table have corresponding read-only objects in the portX25OperTable that return the current operating value. The operating values may be different from these configured values if a configured parameter was configured after the interface was started.
OBJECT-TYPE    
  SEQUENCE OF  
    PortPhyX25AdminEntry

portPhyX25AdminEntry 1.3.6.1.4.1.173.7.3.1.1.1
A list of configured values for an X25 port.
OBJECT-TYPE    
  PortPhyX25AdminEntry  

portPhyX25AdminConnector 1.3.6.1.4.1.173.7.3.1.1.1.1
Physical port interface connector type.
OBJECT-TYPE    
  INTEGER rs232(3), v35(5), rs449(6), rs530(7), x21(8), t1(10), e1(11)  

portPhyX25AdminSpeed 1.3.6.1.4.1.173.7.3.1.1.1.2
This object defines the speed of the X25 port. The speed may only be set to one of a series of reasonable values, and if an attempt is made to set the speed to a value which is within the valid range but not equal to one of these values, the speed will be rounded up. If the connector type of the port is RS232, the port could be a standard port or a high speed port. If the port is a high speed RS232 port, the maximum valid speed is 256000. If the port is a standard RS232 port, the maximum valid speed is 64000 on the FRX4000/SS1840 and 19200 on all other products. It may be possible to set the speed of a standard RS232 port to a speed which is valid for a high speed RS232 port but invalid for a standard RS232 port. In this case, the port may not end up having the invalid speed. The default speed for a standard RS232 port on the FRX6000 is 19200.
OBJECT-TYPE    
  INTEGER  

portPhyX25AdminGenerateClock 1.3.6.1.4.1.173.7.3.1.1.1.3
Specifies whether the port will generate the clock necessary to synchronize traffic over the link.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portPhyX25AdminRcvClockFromDTE 1.3.6.1.4.1.173.7.3.1.1.1.4
This object defines whether the receive clock will be used from the DTE.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portPhyX25AdminDialOut 1.3.6.1.4.1.173.7.3.1.1.1.5
This flag indicates whether the port is connected to a dial modem, and whethter connections will be initiated through dial-in or dial-out calls.
OBJECT-TYPE    
  INTEGER none(1), dialIn(2), dialOut(3)  

portPhyX25AdminInactivityTimer 1.3.6.1.4.1.173.7.3.1.1.1.6
This timer defines in minutes, the period of inactivity allowed between calls. Once the timer expires, the port is disabled untill the next call is placed, if a Dial out port, or the Disconnect Timer expires, if a Dial in port. This variable is only meaningful if the port is a Dial port.
OBJECT-TYPE    
  INTEGER 1..30  

portPhyX25AdminDisconnectTimer 1.3.6.1.4.1.173.7.3.1.1.1.7
This timer defines, in seconds, the length of time a dial-in port will remain disabled after expiration of the InActivity Timer.
OBJECT-TYPE    
  INTEGER 1..255  

portPhyX25AdminSetupTimer 1.3.6.1.4.1.173.7.3.1.1.1.8
This timer determines the length of time, in seconds, that a response must be received by the port, after entering the Linkup state. If a response is not received, the port enters a Failed state.
OBJECT-TYPE    
  INTEGER 1..255  

portPhyX25AdminTrunkFlag 1.3.6.1.4.1.173.7.3.1.1.1.9
This flag, when set, indicates the port is associated with a network trunk group. It will be disabled/enabled if the network trunk is not operational.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portPhyX25AdminTrunkGroup 1.3.6.1.4.1.173.7.3.1.1.1.10
This variable contains a string of 8 bytes, with each byte indicating 8 ports on an RLP that may be a part of a trunk group. Since a TurboFrad has only 1 RLP, only the first byte is valid if the node is an FRX4000. Each port is represented by a single bit within the RLP byte. The bit position represents the port number...for example, if port 2 on RLP 0 was in a trunk group, the first byte of the string would contain x04 and all other bytes would be 0.
OBJECT-TYPE    
  OCTET STRING  

portPhyX25AdminRowStatus 1.3.6.1.4.1.173.7.3.1.1.1.11
This variable is used to manage the creation and deletion of conceptual rows in the portPhyX25AdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

portPhyX25OperTable 1.3.6.1.4.1.173.7.3.1.2
This table contains Netlink Enterprise specific objects to manage an X25 port. Changing one of these parameters may take effect in the operating port immediately or may wait until the interface is restarted depending on the details of the implementation. All of the objects in this table are read-only. The operating values may be different from these configured values if a configured parameter was configured after the interface was started.
OBJECT-TYPE    
  SEQUENCE OF  
    PortPhyX25OperEntry

portPhyX25OperEntry 1.3.6.1.4.1.173.7.3.1.2.1
A list of configured values for an X25 port.
OBJECT-TYPE    
  PortPhyX25OperEntry  

portPhyX25OperConnector 1.3.6.1.4.1.173.7.3.1.2.1.1
Physical port interface connector type.
OBJECT-TYPE    
  INTEGER rs232(3), v35(5), rs449(6), rs530(7), x21(8), t1(10), e1(11)  

portPhyX25OperSpeed 1.3.6.1.4.1.173.7.3.1.2.1.2
This object defines the speed of the X25 port. The speed may only be set to one of a series of reasonable values, and if an attempt is made to set the speed to a value which is within the valid range but not equal to one of these values, the speed will be rounded up. If the connector type of the port is RS232, the port could be a standard port or a high speed port. If the port is a high speed RS232 port, the maximum valid speed is 256000. If the port is a standard RS232 port, the maximum valid speed is 64000 on the FRX4000/SS1840 and 19200 on all other products. It may be possible to set the speed of a standard RS232 port to a speed which is valid for a high speed RS232 port but invalid for a standard RS232 port. In this case, the port may not end up having the invalid speed. The default speed for a standard RS232 port on the FRX6000 is 19200.
OBJECT-TYPE    
  INTEGER  

portPhyX25OperGenerateClock 1.3.6.1.4.1.173.7.3.1.2.1.3
Specifies whether the port will generate the clock necessary to synchronize traffic over the link.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portPhyX25OperRcvClockFromDTE 1.3.6.1.4.1.173.7.3.1.2.1.4
This object defines whether the receive clock will be used from the DTE.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portPhyX25OperDialOut 1.3.6.1.4.1.173.7.3.1.2.1.5
This flag indicates whether the port is connected to a dial modem, and whethter connections will be initiated through dial-in or dial-out calls.
OBJECT-TYPE    
  INTEGER none(1), dialIn(2), dialOut(3)  

portPhyX25OperInactivityTimer 1.3.6.1.4.1.173.7.3.1.2.1.6
This timer defines in minutes, the period of inactivity allowed between calls. Once the timer expires, the port is disabled untill the next call is placed, if a Dial out port, or the Disconnect Timer expires, if a Dial in port. This variable is only meaningful if the port is a Dial port.
OBJECT-TYPE    
  INTEGER 1..30  

portPhyX25OperDisconnectTimer 1.3.6.1.4.1.173.7.3.1.2.1.7
This timer defines, in seconds, the length of time a dial-in port will remain disabled after expiration of the InActivity Timer.
OBJECT-TYPE    
  INTEGER 1..255  

portPhyX25OperSetupTimer 1.3.6.1.4.1.173.7.3.1.2.1.8
This timer determines the length of time, in seconds, that a response must be received by the port, after entering the Linkup state. If a response is not received, the port enters a Failed state.
OBJECT-TYPE    
  INTEGER 1..255  

portPhyX25OperTrunkFlag 1.3.6.1.4.1.173.7.3.1.2.1.9
This flag, when set, indicates the port is associated with a network trunk group. It will be disabled/enabled if the network trunk is not operational.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portPhyX25OperTrunkGroup 1.3.6.1.4.1.173.7.3.1.2.1.10
This variable contains a string of 8 bytes, with each byte indicating a port on this RLP that may be a part of a trunk group.
OBJECT-TYPE    
  OCTET STRING  

portLogicalX25AdminTable 1.3.6.1.4.1.173.7.3.1.3
This table contains Netlink Enterprise specific objects to manage an X25 Logical port. Changing one of these parameters may take effect in the operating port immediately or may wait until the interface is restarted depending on the details of the implementation. The operating values may be different from these configured values if a configured parameter was configured after the interface was started.
OBJECT-TYPE    
  SEQUENCE OF  
    PortLogicalX25AdminEntry

portLogicalX25AdminEntry 1.3.6.1.4.1.173.7.3.1.3.1
A list of configured values for an X25 logical port.
OBJECT-TYPE    
  PortLogicalX25AdminEntry  

portLogicalX25AdminFrDlci 1.3.6.1.4.1.173.7.3.1.3.1.1
The DLCI number used to identify the entry in the table. The range is 16-991.
OBJECT-TYPE    
  INTEGER 16..991  

portLogicalX25AdminCxnPriority 1.3.6.1.4.1.173.7.3.1.3.1.2
This field sets the priority of the connection among others on the physical port. The range is 0 for lowest priority to 9 for the highest priority.
OBJECT-TYPE    
  INTEGER 0..9  

portLogicalX25AdminRfc1490 1.3.6.1.4.1.173.7.3.1.3.1.3
This field indicates the encapsulation method used
OBJECT-TYPE    
  INTEGER annexG(1), rfc1490(2)  

portLogicalX25AdminBAG 1.3.6.1.4.1.173.7.3.1.3.1.4
Assigns this DLCI to one of sixteen groups whose parameters regulate bandwidth usage. A 0 value indicates the DLCI does not use BAGs
OBJECT-TYPE    
  INTEGER 0..16  

portLogicalX25AdminRowStatus 1.3.6.1.4.1.173.7.3.1.3.1.5
This variable is used to manage the creation and deletion of conceptual rows in the portLogicalX25AdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

portLogicalX25OperTable 1.3.6.1.4.1.173.7.3.1.4
This table contains Netlink Enterprise specific objects to manage an X25 Logical port. Changing one of these parameters may take effect in the operating port immediately or may wait until the interface is restarted depending on the details of the implementation. The operating values may be different from these configured values if a configured parameter was configured after the interface was started.
OBJECT-TYPE    
  SEQUENCE OF  
    PortLogicalX25OperEntry

portLogicalX25OperEntry 1.3.6.1.4.1.173.7.3.1.4.1
A list of configured values for an X25 port.
OBJECT-TYPE    
  PortLogicalX25OperEntry  

portLogicalX25OperFrDlci 1.3.6.1.4.1.173.7.3.1.4.1.1
The DLCI number used to identify the entry in the table. The range is 16-991.
OBJECT-TYPE    
  INTEGER 1..255  

portLogicalX25OperCxnPriority 1.3.6.1.4.1.173.7.3.1.4.1.2
This field sets the priority of the connection among others on the physical port. The range is 0 for lowest priority to 9 for the highest priority.
OBJECT-TYPE    
  INTEGER 0..9  

portLogicalX25OperRfc1490 1.3.6.1.4.1.173.7.3.1.4.1.3
This field indicates the encapsulation method used
OBJECT-TYPE    
  INTEGER annexG(1), rfc1490(2)  

portLogicalX25OperBAG 1.3.6.1.4.1.173.7.3.1.4.1.4
Assigns this DLCI to one of sixteen groups whose parameters regulate bandwidth usage.
OBJECT-TYPE    
  INTEGER 1..16  

portX25AdminTable 1.3.6.1.4.1.173.7.3.1.5
This table contains Netlink Enterprise specific objects to manage an X25 port. Changing one of these parameters may take effect in the operating port immediately or may wait until the interface is restarted depending on the details of the implementation. Most of the objects in this read-write table have corresponding read-only objects in the portX25OperTable that return the current operating value. The operating values may be different from these configured values if a configured parameter was configured after the interface was started.
OBJECT-TYPE    
  SEQUENCE OF  
    PortX25AdminEntry

portX25AdminEntry 1.3.6.1.4.1.173.7.3.1.5.1
A list of configured values for an X25 port.
OBJECT-TYPE    
  PortX25AdminEntry  

portX25AdminBlockedFlag 1.3.6.1.4.1.173.7.3.1.5.1.1
A flag which when set, means the port should not be enabled after a boot-up of the node.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25AdminFlowCtrlNeg 1.3.6.1.4.1.173.7.3.1.5.1.2
A flag which if set, permits negotiation of the flow control parameters on a per call basis. If N is selected, the default packet and window sizes will be used. If Y is selected, the packet or window size in a call packet (up to the configured Max Packet Size or Max Window Size) is used.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25AdminThruptClassNeg 1.3.6.1.4.1.173.7.3.1.5.1.3
A flag which ,if set, permists negotiation of the throughput class for either direction of data transmission on a per call basis. If N is selected, the configured Max Throughput Class value is used. If Y, any throughput class in a call packet (up to the Max Thruput Class) is used.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25AdminLocChgPrev 1.3.6.1.4.1.173.7.3.1.5.1.4
If Y is selected, no calls can be charged to port. Incoming calls from the network with reverse charge specified will be rejected. Outgoing calls will insert reverse charge in the call packet if not already included.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25AdminRevChgAccpt 1.3.6.1.4.1.173.7.3.1.5.1.5
A flag, if set, that authorizes transmission of incoming calls that request the reverse charge facility. If N is selected, and a call requests it, it will not be transmitted.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25AdminFastSelAccpt 1.3.6.1.4.1.173.7.3.1.5.1.6
A flag, if set, that authorizes transmission of incoming calls that request the Fast Select facility.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25AdminInCallBar 1.3.6.1.4.1.173.7.3.1.5.1.7
An X25 facility that prevents transmission of incoming calls to the local DTE.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25AdminOutCallBar 1.3.6.1.4.1.173.7.3.1.5.1.8
An X25 facility that prevents transmission of incoming calls to the local DTE.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25AdminMaxPktSize 1.3.6.1.4.1.173.7.3.1.5.1.9
The maximum data packet size that will be allowed to pass through this port.
OBJECT-TYPE    
  INTEGER 128..4096  

portX25AdminDefPktSize 1.3.6.1.4.1.173.7.3.1.5.1.10
This is the size that will be assigned to an incoming call setup packet if the packet does not request a packet size.
OBJECT-TYPE    
  INTEGER 16..4096  

portX25AdminMaxWinSize 1.3.6.1.4.1.173.7.3.1.5.1.11
This is the maximum number of unacknowledged packets per logical channel that can pass through this port.
OBJECT-TYPE    
  INTEGER 2..7  

portX25AdminDefWinSize 1.3.6.1.4.1.173.7.3.1.5.1.12
This size will be assigned to an incoming call setup packet if the packet doesn't request a window size.
OBJECT-TYPE    
  INTEGER 1..7  

portX25AdminMaxThruptClass 1.3.6.1.4.1.173.7.3.1.5.1.13
This specifies the default throughput class that will be inserted into a Call Request packet if Thruput Class negotiation is not enabled or if a thruput class is not requested in the call request.
OBJECT-TYPE    
  INTEGER 3..13  

portX25AdminCUGPref 1.3.6.1.4.1.173.7.3.1.5.1.14
This flag, if set, indicates the port belongs to at least one CUG.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25AdminCUGIndex 1.3.6.1.4.1.173.7.3.1.5.1.15
This number is an index into a Closed User Group table which identifies the default Closed User Group for the port.
OBJECT-TYPE    
  INTEGER 1..100  

portX25AdminCUGIncAccess 1.3.6.1.4.1.173.7.3.1.5.1.16
This flag, when set, indicates whether this port will be allowed to receive calls from outside its CUGs.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25AdminCUGOutAccess 1.3.6.1.4.1.173.7.3.1.5.1.17
This flag, when set, indicates whether this port will be allowed to make calls outside its CUGs.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25OperTable 1.3.6.1.4.1.173.7.3.1.6
This table contains Netlink Enterprise specific objects to manage an X25 port. Changing one of these parameters may take effect in the operating port immediately or may wait until the interface is restarted depending on the details of the implementation. The objects in this read-only table corresponding read-only objects in the portX25OperTable that return the current operating value. The operating values may be different from these configured values if a configured parameter was configured after the interface was started.
OBJECT-TYPE    
  SEQUENCE OF  
    PortX25OperEntry

portX25OperEntry 1.3.6.1.4.1.173.7.3.1.6.1
A list of configured values for an X25 port.
OBJECT-TYPE    
  PortX25OperEntry  

portX25OperBlockedFlag 1.3.6.1.4.1.173.7.3.1.6.1.1
A flag which when set, means the port should not be enabled after a boot-up of the node.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25OperFlowCtrlNeg 1.3.6.1.4.1.173.7.3.1.6.1.2
A flag which if set, permits negotiation of the flow control parameters on a per call basis. If N is selected, the default packet and window sizes will be used. If Y is selected, the packet or window size in a call packet (up to the configured Max Packet Size or Max Window Size) is used.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25OperThruptClassNeg 1.3.6.1.4.1.173.7.3.1.6.1.3
A flag which ,if set, permists negotiation of the throughput class for either direction of data transmission on a per call basis. If N is selected, the configured Max Throughput Class value is used. If Y, any throughput class in a call packet (up to the Max Thruput Class) is used.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25OperLocChgPrev 1.3.6.1.4.1.173.7.3.1.6.1.4
If Y is selected, no calls can be charged to port. Incoming calls from the network with reverse charge specified will be rejected. Outgoing calls will insert reverse charge in the call packet if not already included.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25OperRevChgAccpt 1.3.6.1.4.1.173.7.3.1.6.1.5
A flag, if set, that authorizes transmission of incoming calls that request the reverse charge facility. If N is selected, and a call requests it, it will not be transmitted.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25OperFastSelAccpt 1.3.6.1.4.1.173.7.3.1.6.1.6
A flag, if set, that authorizes transmission of incoming calls that request the Fast Select facility.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25OperInCallBar 1.3.6.1.4.1.173.7.3.1.6.1.7
An X25 facility that prevents transmission of incoming calls to the local DTE.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25OperOutCallBar 1.3.6.1.4.1.173.7.3.1.6.1.8
An X25 facility that prevents transmission of incoming calls to the local DTE.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25OperMaxPktSize 1.3.6.1.4.1.173.7.3.1.6.1.9
The maximum data packet size that will be allowed to pass through this port.
OBJECT-TYPE    
  INTEGER 128..4096  

portX25OperDefPktSize 1.3.6.1.4.1.173.7.3.1.6.1.10
This is the size that will be assigned to an incoming call setup packet if the packet does not request a packet size.
OBJECT-TYPE    
  INTEGER 16..4096  

portX25OperMaxWinSize 1.3.6.1.4.1.173.7.3.1.6.1.11
This is the maximum number of unacknowledged packets per logical channel that can pass through this port.
OBJECT-TYPE    
  INTEGER 2..7  

portX25OperDefWinSize 1.3.6.1.4.1.173.7.3.1.6.1.12
This size will be assigned to an incoming call setup packet if the packet doesn't request a window size.
OBJECT-TYPE    
  INTEGER 1..7  

portX25OperMaxThruptClass 1.3.6.1.4.1.173.7.3.1.6.1.13
This specifies the default throughput class that will be inserted into a Call Request packet if Thruput Class negotiation is not enabled or if a thruput class is not requested in the call request.
OBJECT-TYPE    
  INTEGER 3..13  

portX25OperCUGPref 1.3.6.1.4.1.173.7.3.1.6.1.14
This flag, if set, indicates the port belongs to at least one CUG.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25OperCUGIndex 1.3.6.1.4.1.173.7.3.1.6.1.15
This number is an index into a Closed User Group table which identifies the default Closed User Group for the port.
OBJECT-TYPE    
  INTEGER 1..100  

portX25OperCUGIncAccess 1.3.6.1.4.1.173.7.3.1.6.1.16
This flag, when set, indicates whether this port will be able to receive calls from outside its CUGs.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portX25OperCUGOutAccess 1.3.6.1.4.1.173.7.3.1.6.1.17
This flag, when set, indicates whether this port will be able to make calls outside its CUGs.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portFrGroup 1.3.6.1.4.1.173.7.3.2
OBJECT IDENTIFIER    

portFrConfigTable 1.3.6.1.4.1.173.7.3.2.1
A list of Frame Relay ports . The number of entries will be the number of Frame Relay ports on the node.
OBJECT-TYPE    
  SEQUENCE OF  
    PortFrEntry

portFrEntry 1.3.6.1.4.1.173.7.3.2.1.1
An Frame Relay Port entry containing objects relating to the port that are configurable by the user.
OBJECT-TYPE    
  PortFrEntry  

portFrRlpIndex 1.3.6.1.4.1.173.7.3.2.1.1.1
The RLP number of the Frame Relay port. It will be in the range 1-8.
OBJECT-TYPE    
  INTEGER  

portFrPortIndex 1.3.6.1.4.1.173.7.3.2.1.1.2
The Port number of the Frame Relay port. It will be in the range 1-8 for a physical port. It will be in the range 9-64 for a Frame Relay logical port.
OBJECT-TYPE    
  INTEGER  

portFrBlockedFlag 1.3.6.1.4.1.173.7.3.2.1.1.3
A flag which when set, means the port should not be enabled after a boot-up of the node.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portFrMaxBytesPerFrame 1.3.6.1.4.1.173.7.3.2.1.1.4
The maximum number of bytes allowed in an I Frame for this Frame Relay port.
OBJECT-TYPE    
  INTEGER 16..4096  

portFrT392Timer 1.3.6.1.4.1.173.7.3.2.1.1.5
This timer indicates how long the network will wait between Status Enquiry messages before recording an error. It should be greater than or equal to the frDlcmiPollingInterval variable in the RFC1315 Mib.
OBJECT-TYPE    
  INTEGER 5..30  

portFrOutgoingRateControl 1.3.6.1.4.1.173.7.3.2.1.1.6
This is a flag which, when set, enables the enforcement of the Outgoing Rate Control parameters.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portFrBandwidthAllocation 1.3.6.1.4.1.173.7.3.2.1.1.7
This is a flag which, when set, enables whether the bandwidth allocation will be enforced.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portFrConnector 1.3.6.1.4.1.173.7.3.2.1.1.8
This defines the connector type of the Frame Relay port.
OBJECT-TYPE    
  INTEGER rs232(3), v35(5), rs449(6), rs530(7), x21(8), t1(10), e1(11)  

portFrLogicalDCE 1.3.6.1.4.1.173.7.3.2.1.1.9
This defines the port as logical DCE or DTE.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portFrGenClock 1.3.6.1.4.1.173.7.3.2.1.1.10
This specifies whether the port will generate the clock necessary to synchronize traffic over the link.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portFrRcvClkFrmDTE 1.3.6.1.4.1.173.7.3.2.1.1.11
This allows the clock to be looped back from the DTE using the TT (Terminal Timing) signal, which can be helpful on high-speed lines.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portFrLLM 1.3.6.1.4.1.173.7.3.2.1.1.12
This determines whether, and what type of, configurable network management (status enquiries) will be allowed.
OBJECT-TYPE    
  INTEGER none(1), lmi(2), annexd(3)  

portFrRowStatus 1.3.6.1.4.1.173.7.3.2.1.1.13
This variable is used to manage the creation and deletion of conceptual rows in the portFrConfigTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

portFrSpeed 1.3.6.1.4.1.173.7.3.2.1.1.14
This object defines the speed of the Frame Relay port. The speed may only be set to one of a series of reasonable values, and if an attempt is made to set the speed to a value which is within the valid range but not equal to one of these values, the speed will be rounded up. If the connector type of the port is RS232, the port could be a standard port or a high speed port. If the port is a high speed RS232 port, the maximum valid speed is 256000. If the port is a standard RS232 port, the maximum valid speed is 64000 on the FRX4000/SS1840 and 19200 on all other products. It may be possible to set the speed of a standard RS232 port to a speed which is valid for a high speed RS232 port but invalid for a standard RS232 port. In this case, the port may not end up having the invalid speed. The default speed for a standard RS232 port on the FRX6000 is 19200.
OBJECT-TYPE    
  INTEGER 75..2048000  

portFrBackupUseOnly 1.3.6.1.4.1.173.7.3.2.1.1.15
This object determines whether all DLCIs on the port will be reserved exclusively as backups for other DLCIs in the same node. If yes is specified for this object, the port will remain disabled until needed for backup.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portDLCIConfigTable 1.3.6.1.4.1.173.7.3.2.2
A list of DLCI's on Frame Relay ports . The number of entries will be the number of DLCIs on all the Frame Relay ports on a node.
OBJECT-TYPE    
  SEQUENCE OF  
    PortDLCIEntry

portDLCIEntry 1.3.6.1.4.1.173.7.3.2.2.1
An Frame Relay Port DLCI entry relating to the Rate Control Information that is configurable by the user.
OBJECT-TYPE    
  PortDLCIEntry  

portDLCIRlpIndex 1.3.6.1.4.1.173.7.3.2.2.1.1
The RLP number on which the DLCI is located. The range for this is 1-8.
OBJECT-TYPE    
  INTEGER  

portDLCIPortIndex 1.3.6.1.4.1.173.7.3.2.2.1.2
The port number on which the DLCI is located. The range for this is 1-8 for a physical FR port and 9-64 for a logical FR port.
OBJECT-TYPE    
  INTEGER  

portDLCIIndex 1.3.6.1.4.1.173.7.3.2.2.1.3
The DLCI number used to identify the entry in the table. The range is 16-991.
OBJECT-TYPE    
  INTEGER  

portDLCIIncomingCIR 1.3.6.1.4.1.173.7.3.2.2.1.4
The committed information rate that is supported on the DLCI for incoming data.
OBJECT-TYPE    
  INTEGER 0..2000  

portDLCIOutgoingCIR 1.3.6.1.4.1.173.7.3.2.2.1.5
The committed information rate that is supported on the DLCI for outgoing data.
OBJECT-TYPE    
  INTEGER 0..2000  

portDLCIIncomingBc 1.3.6.1.4.1.173.7.3.2.2.1.6
The committed burst size is the maximum amount of data to be transmitted under normal conditions within the time period defined by Bc/Cir that is supported on the DLCI for incoming data.
OBJECT-TYPE    
  INTEGER  

portDLCIOutgoingBc 1.3.6.1.4.1.173.7.3.2.2.1.7
The committed burst size is the maximum amount of data to be transmitted under normal conditions within the time period defined by Bc/Cir that is supported on the DLCI for Outgoing data.
OBJECT-TYPE    
  INTEGER  

portDLCIIncomingBe 1.3.6.1.4.1.173.7.3.2.2.1.8
The excess burst size is the maximum amount of incoming data in excess of the committed burst size that the network will try to transfer during the time interval determined by Bc/Cir on this DLCI.
OBJECT-TYPE    
  INTEGER 0..32767  

portDLCIOutgoingBe 1.3.6.1.4.1.173.7.3.2.2.1.9
The excess burst size is the maximum amount of incoming data in excess of the committed burst size that the network will try to transfer during the time interval determined by Bc/Cir on this DLCI.
OBJECT-TYPE    
  INTEGER 0..32767  

portDLCIBecnRecoveryCnt 1.3.6.1.4.1.173.7.3.2.2.1.10
The BECN recovery Count is a method of controlling the rate of return to max traffic flow after it has been reduced due to congestion. The value determines the number of packets received sequentially without BECN set, before increasing the Excess Burst Size by 1/8 of it's configured value.
OBJECT-TYPE    
  INTEGER 0..255  

portDLCIPriority 1.3.6.1.4.1.173.7.3.2.2.1.11
This field sets the priority of the DLCI among others on the physical port. The range is 0 for lowest priority to 4 for the highest priority.
OBJECT-TYPE    
  INTEGER 0..4  

portDLCIRowStatus 1.3.6.1.4.1.173.7.3.2.2.1.12
This variable is used to manage the creation and deletion of conceptual rows in the portDLCIConfigTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned. Also note that deleting a DLCI entry will only remove it from the database file, and it's existence will still be known by the protocol until the node is rebooted.
OBJECT-TYPE    
  RowStatus  

portDLCIBackupGroup 1.3.6.1.4.1.173.7.3.2.2.1.13
This object specifies (if configured as any number other than zero) that this is a primary DLCI, and identifies the backup DLCI(s) (in a Frame Relay backup group) that will take over if this DLCI fails. This is applicable only on an initiating node, which is the node that will initiate the switchover to a backup DLCI. At switchover, the initiating node notifies the remote node of the change.
OBJECT-TYPE    
  INTEGER  

portDLCIBackupProtEnb 1.3.6.1.4.1.173.7.3.2.2.1.14
This object specifies whether the DLCI will be used as a non-initiating backup DLCI. The DLCI will wait for a backup protocol message from the initiating end, telling the backup where to send the rest of the messages.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portFrBackupGroupTable 1.3.6.1.4.1.173.7.3.2.3
A Table describes the Frame Relay Backup MIB .
OBJECT-TYPE    
  SEQUENCE OF  
    FrBackupEntry

portFrBackupEntry 1.3.6.1.4.1.173.7.3.2.3.1
This Entry contains the SNMP objects that are used for configurating the Frame Relay Backup.
OBJECT-TYPE    
  FrBackupEntry  

portFrBackupRLP 1.3.6.1.4.1.173.7.3.2.3.1.1
This RLP number identifies the RLP containing the primary and backup DLCIs.
OBJECT-TYPE    
  INTEGER 1..8  

portFrBackupPort 1.3.6.1.4.1.173.7.3.2.3.1.2
This Port number is the physical port on which the backup DLCI is being configured.
OBJECT-TYPE    
  INTEGER 1..8  

portFrBackupDLCI 1.3.6.1.4.1.173.7.3.2.3.1.3
This DLCI number is the backup being configured.
OBJECT-TYPE    
  INTEGER 16..991  

portFrBackupGroup 1.3.6.1.4.1.173.7.3.2.3.1.4
This Group number is the backup being configured.
OBJECT-TYPE    
  INTEGER 1..255  

portFrBackupWaitTimer 1.3.6.1.4.1.173.7.3.2.3.1.5
This is the time after a primary DLCI failure that the software will wait for this DLCI to become active before checking the next backup DLCI. If the backup does not become active before the timer expires, the software will search the backup group for the next available backup.
OBJECT-TYPE    
  INTEGER 0..65535  

portFrBackupProtEnab 1.3.6.1.4.1.173.7.3.2.3.1.6
This enables or disables the backup protocol on the specified DLCI. It should be set to yes if and only if the remote device is an FRX4000 or FRX6000 with the backup protocol enabled on the remote DLCI connected to this backup group entry.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portFrBackupRowStatus 1.3.6.1.4.1.173.7.3.2.3.1.7
This variable is used to manage the creation and deletion of conceptual rows in the portFrBackupGroupTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

portBsciGroup 1.3.6.1.4.1.173.7.3.4
OBJECT IDENTIFIER    

portBsciAdminTable 1.3.6.1.4.1.173.7.3.4.1
A list of BSC Interactive ports . The number of entries will be the number of BSC Interactive ports on the node.
OBJECT-TYPE    
  SEQUENCE OF  
    PortBsciAdminEntry

portBsciAdminEntry 1.3.6.1.4.1.173.7.3.4.1.1
A BSCI Interactive Port entry containing objects relating to the port that are configurable by the user.
OBJECT-TYPE    
  PortBsciAdminEntry  

portBsciAdminBlockedFlag 1.3.6.1.4.1.173.7.3.4.1.1.1
Causes the port to be enabled or disabled at node IPL.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

portBsciAdminConnector 1.3.6.1.4.1.173.7.3.4.1.1.2
Physical port interface connector type.
OBJECT-TYPE    
  INTEGER rs232(3), v35(5), rs449(6), rs530(7), x21(8), t1(10)  

portBsciAdminSpeed 1.3.6.1.4.1.173.7.3.4.1.1.3
Data transmission rate in bits per second.
OBJECT-TYPE    
  INTEGER 75..19200  

portBsciAdminRetransmitInterval 1.3.6.1.4.1.173.7.3.4.1.1.4
Length of time before the node will transmit an I-frame if the previous transmission is not acknowledged.
OBJECT-TYPE    
  INTEGER 1..9999  

portBsciAdminMAXRetransmits 1.3.6.1.4.1.173.7.3.4.1.1.5
Maximum number of times the node will attempt to send an I-frame after a retransmission period expiration.
OBJECT-TYPE    
  INTEGER 1..99  

portBsciAdminMaxBytesPerFrame 1.3.6.1.4.1.173.7.3.4.1.1.6
Maximum frame size that will be transmitted on the port.
OBJECT-TYPE    
  INTEGER 25..4105  

portBsciAdminGenerateClock 1.3.6.1.4.1.173.7.3.4.1.1.7
Specifies whether the port will generate the clock necessary to synchronize traffic over the link.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciAdminRcvClockFromDTE 1.3.6.1.4.1.173.7.3.4.1.1.8
Allows the clock to be looped back from the DTE using the TT (Terminal Timing) signal.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciAdminPadType 1.3.6.1.4.1.173.7.3.4.1.1.9
BSCI Pad Type
OBJECT-TYPE    
  INTEGER tpad(1), hpad(2)  

portBsciAdminUseEBCDIC 1.3.6.1.4.1.173.7.3.4.1.1.10
Specifies whether all devices on a line use the same character set for successive session polls.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciAdminCallInfoInRequestPacket 1.3.6.1.4.1.173.7.3.4.1.1.11
Specifies whether the user will have the option of including call information in a call request packet.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciAdminClearVCOnLastDeviceDown 1.3.6.1.4.1.173.7.3.4.1.1.12
Causes the virtual circuit to be cleared when no terminals are using it.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciAdminTransTextSupported 1.3.6.1.4.1.173.7.3.4.1.1.13
Causes all characters transmitted to be treated as data.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciAdminEndToEndAck 1.3.6.1.4.1.173.7.3.4.1.1.14
Allows management of acknowledgments end to end across the network rather than locally at each end.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciAdminFullDuplex 1.3.6.1.4.1.173.7.3.4.1.1.15
Specifies full-duplex transmission.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciAdminMultidrop 1.3.6.1.4.1.173.7.3.4.1.1.16
Specifies whether transmission will be multidrop.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciAdminSlowPollRetryCount 1.3.6.1.4.1.173.7.3.4.1.1.17
Specifies how many times the control unit will be polled before it is put on the slow poll list.
OBJECT-TYPE    
  INTEGER 10..150  

portBsciAdminSlowPollRetryFreq 1.3.6.1.4.1.173.7.3.4.1.1.18
Specifies the number of times active control units will be polled between pollings on the slow poll list.
OBJECT-TYPE    
  INTEGER 1..200  

portBsciAdminStartSynchChars 1.3.6.1.4.1.173.7.3.4.1.1.19
Specifies the number of synchronization characters that will be added to the beginning of each frame.
OBJECT-TYPE    
  INTEGER 2..10  

portBsciAdminEndPadChars 1.3.6.1.4.1.173.7.3.4.1.1.20
Specifies the number of padding characters that will be added to the end of each frame.
OBJECT-TYPE    
  INTEGER 1..10  

portBsciAdminPollInterval 1.3.6.1.4.1.173.7.3.4.1.1.21
Specifies the time between passes through the polling list.
OBJECT-TYPE    
  INTEGER 100..1000  

portBsciAdminNoResponseTimer 1.3.6.1.4.1.173.7.3.4.1.1.22
Activated after transmission of a general poll or a data frame.
OBJECT-TYPE    
  INTEGER 2..10  

portBsciAdminNoResponseRetryCount 1.3.6.1.4.1.173.7.3.4.1.1.23
Specifies how many times the user device will be polled before control is passed on the next cluster.
OBJECT-TYPE    
  INTEGER 1..255  

portBsciAdminErrorRetransmitCount 1.3.6.1.4.1.173.7.3.4.1.1.24
Specifies the number of times the Netlink device will resend a block of data after the receiving device has detected an error in that block.
OBJECT-TYPE    
  INTEGER 1..255  

portBsciAdminNAKRetryCount 1.3.6.1.4.1.173.7.3.4.1.1.25
Specifies the number of times the Netlink device will send a frame when the receiving device is unable to acknowledge.
OBJECT-TYPE    
  INTEGER 1..255  

portBsciAdminBlockCheck 1.3.6.1.4.1.173.7.3.4.1.1.26
Sets the redundancy check parameter.
OBJECT-TYPE    
  INTEGER crc16(1), even-lrc(2), odd-lrc(3)  

portBsciAdminDataMode 1.3.6.1.4.1.173.7.3.4.1.1.27
Sets the parity parameter.
OBJECT-TYPE    
  INTEGER odd-7bit(1), even-7bit(2), none-8bit(3)  

portBsciAdminRowStatus 1.3.6.1.4.1.173.7.3.4.1.1.28
This variable is used to manage the creation and deletion of conceptual rows in the portBsciAdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

portBsciAdminAnswerNonConfigured 1.3.6.1.4.1.173.7.3.4.1.1.29
Only valid if pad type is HPAD. If yes, the HPAD will respond to all devices on the line. If no, the HPAD will respond only to those devices that are configured on the node.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciAdminActivateConnectionWithoutPoll 1.3.6.1.4.1.173.7.3.4.1.1.30
Only valid if pad type is TPAD. If yes, will active the TPAD connection without a poll of the connected device.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciOperTable 1.3.6.1.4.1.173.7.3.4.2
A list of BSC Interactive ports . The number of entries will be the number of BSC Interactive ports on the node.
OBJECT-TYPE    
  SEQUENCE OF  
    PortBsciOperEntry

portBsciOperEntry 1.3.6.1.4.1.173.7.3.4.2.1
A BSCI Interactive Port entry containing objects relating to the port that are configurable by the user.
OBJECT-TYPE    
  PortBsciOperEntry  

portBsciOperBlockedFlag 1.3.6.1.4.1.173.7.3.4.2.1.1
Causes the port to be enabled or disabled at node IPL.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

portBsciOperConnector 1.3.6.1.4.1.173.7.3.4.2.1.2
Physical port interface connector type.
OBJECT-TYPE    
  INTEGER rs232(3), v35(5), rs449(6), rs530(7), x21(8), t1(10)  

portBsciOperSpeed 1.3.6.1.4.1.173.7.3.4.2.1.3
Data transmission rate in bits per second.
OBJECT-TYPE    
  INTEGER  

portBsciOperRetransmitInterval 1.3.6.1.4.1.173.7.3.4.2.1.4
Length of time before the node will transmit an I-frame if the previous transmission is not acknowledged.
OBJECT-TYPE    
  INTEGER 1..9999  

portBsciOperMAXRetransmits 1.3.6.1.4.1.173.7.3.4.2.1.5
Maximum number of times the node will attempt to send an I-frame after a retransmission period expiration.
OBJECT-TYPE    
  INTEGER 1..99  

portBsciOperMaxBytesPerFrame 1.3.6.1.4.1.173.7.3.4.2.1.6
Maximum frame size that will be transmitted on the port.
OBJECT-TYPE    
  INTEGER 25..4105  

portBsciOperGenerateClock 1.3.6.1.4.1.173.7.3.4.2.1.7
Specifies whether the port will generate the clock necessary to synchronize traffic over the link.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciOperRcvClockFromDTE 1.3.6.1.4.1.173.7.3.4.2.1.8
Allows the clock to be looped back from the DTE using the TT (Terminal Timing) signal.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciOperPadType 1.3.6.1.4.1.173.7.3.4.2.1.9
BSCI Pad Type
OBJECT-TYPE    
  INTEGER tpad(1), hpad(2)  

portBsciOperUseEBCDIC 1.3.6.1.4.1.173.7.3.4.2.1.10
Specifies whether all devices on a line use the same character set for successive session polls.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciOperCallInfoInRequestPacket 1.3.6.1.4.1.173.7.3.4.2.1.11
Specifies whether the user will have the option of including call information in a call request packet.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciOperClearVCOnLastDeviceDown 1.3.6.1.4.1.173.7.3.4.2.1.12
Causes the virtual circuit to be cleared when no terminals are using it.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciOperTransTextSupported 1.3.6.1.4.1.173.7.3.4.2.1.13
Causes all characters transmitted to be treated as data.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciOperEndToEndAck 1.3.6.1.4.1.173.7.3.4.2.1.14
Allows management of acknowledgments end to end across the network rather than locally at each end.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciOperFullDuplex 1.3.6.1.4.1.173.7.3.4.2.1.15
Specifies full-duplex transmission.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciOperMultidrop 1.3.6.1.4.1.173.7.3.4.2.1.16
Specifies whether transmission will be multidrop.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciOperSlowPollRetryCount 1.3.6.1.4.1.173.7.3.4.2.1.17
Specifies how many times the control unit will be polled before it is put on the slow poll list.
OBJECT-TYPE    
  INTEGER 10..150  

portBsciOperSlowPollRetryFreq 1.3.6.1.4.1.173.7.3.4.2.1.18
Specifies the number of times active control units will be polled between pollings on the slow poll list.
OBJECT-TYPE    
  INTEGER 1..200  

portBsciOperStartSynchChars 1.3.6.1.4.1.173.7.3.4.2.1.19
Specifies the number of synchronization characters that will be added to the beginning of each frame.
OBJECT-TYPE    
  INTEGER 2..10  

portBsciOperEndPadChars 1.3.6.1.4.1.173.7.3.4.2.1.20
Specifies the number of padding characters that will be added to the end of each frame.
OBJECT-TYPE    
  INTEGER 1..10  

portBsciOperPollInterval 1.3.6.1.4.1.173.7.3.4.2.1.21
Specifies the time between passes through the polling list.
OBJECT-TYPE    
  INTEGER 100..1000  

portBsciOperNoResponseTimer 1.3.6.1.4.1.173.7.3.4.2.1.22
Activated after transmission of a general poll or a data frame.
OBJECT-TYPE    
  INTEGER 2..10  

portBsciOperNoResponseRetryCount 1.3.6.1.4.1.173.7.3.4.2.1.23
Specifies how many times the user device will be polled before control is passed on the next cluster.
OBJECT-TYPE    
  INTEGER 1..255  

portBsciOperErrorRetransmitCount 1.3.6.1.4.1.173.7.3.4.2.1.24
Specifies the number of times the Netlink device will resend a block of data after the receiving device has detected an error in that block.
OBJECT-TYPE    
  INTEGER 1..255  

portBsciOperNAKRetryCount 1.3.6.1.4.1.173.7.3.4.2.1.25
Specifies the number of times the Netlink device will send a frame when the receiving device is unable to acknowledge.
OBJECT-TYPE    
  INTEGER 1..255  

portBsciOperBlockCheck 1.3.6.1.4.1.173.7.3.4.2.1.26
Sets the redundancy check parameter.
OBJECT-TYPE    
  INTEGER crc16(1), even-lrc(2), odd-lrc(3)  

portBsciOperDataMode 1.3.6.1.4.1.173.7.3.4.2.1.27
Sets the parity parameter.
OBJECT-TYPE    
  INTEGER odd-7bit(1), even-7bit(2), none-8bit(3)  

portBsciOperAnswerNonConfigured 1.3.6.1.4.1.173.7.3.4.2.1.28
Only valid if pad type is HPAD. If yes, the HPAD will respond to all devices on the line. If no, the HPAD will respond only to those devices that are configured on the node.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portBsciOperActivateConnectionWithoutPoll 1.3.6.1.4.1.173.7.3.4.2.1.29
Only valid if pad type is TPAD. If yes, will active the TPAD connection without a poll of the connected device.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

bsciSubscrAdminTable 1.3.6.1.4.1.173.7.3.4.3
A list of BSC Interactive port subscribers.
OBJECT-TYPE    
  SEQUENCE OF  
    BsciSubscrAdminEntry

bsciSubscrAdminEntry 1.3.6.1.4.1.173.7.3.4.3.1
A BSCI Interactive Port Subscriber entry containing objects relating to the port that are configurable by the user.
OBJECT-TYPE    
  BsciSubscrAdminEntry  

bsciSubscrAdminSequence 1.3.6.1.4.1.173.7.3.4.3.1.1
Subscriber index for a specific BSCI port subscriber.
OBJECT-TYPE    
  INTEGER 1..16  

bsciSubscrAdminLocalID 1.3.6.1.4.1.173.7.3.4.3.1.2
Subscriber address of the local end of a BSCI connection.
OBJECT-TYPE    
  NlSubscriberAddress  

bsciSubscrAdminRemoteID 1.3.6.1.4.1.173.7.3.4.3.1.3
Subscriber address of the remote end of a BSCI connection.
OBJECT-TYPE    
  NlSubscriberAddress  

bsciSubscrAdminAutocall 1.3.6.1.4.1.173.7.3.4.3.1.4
Causes a BSCI TPAD to automatically call its HPAD when the controller becomes active.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

bsciSubscrAdminAutocallRtyTimer 1.3.6.1.4.1.173.7.3.4.3.1.5
Time between autocall retries.
OBJECT-TYPE    
  INTEGER 15..255  

bsciSubscrAdminAutocallMaxRtry 1.3.6.1.4.1.173.7.3.4.3.1.6
Maximum number of times an autocall will be sent.
OBJECT-TYPE    
  INTEGER 0..255  

bsciSubscrAdminConnectionID 1.3.6.1.4.1.173.7.3.4.3.1.7
Identifier that will link the BSCI port with a device configured in the BSCI Devices Table.
OBJECT-TYPE    
  INTEGER 0..255  

bsciSubscrAdminRowStatus 1.3.6.1.4.1.173.7.3.4.3.1.8
This variable is used to manage the creation and deletion of conceptual rows in the bsciDevAdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

bsciSubscrOperTable 1.3.6.1.4.1.173.7.3.4.4
A list of BSC Interactive port subscribers.
OBJECT-TYPE    
  SEQUENCE OF  
    BsciSubscrOperEntry

bsciSubscrOperEntry 1.3.6.1.4.1.173.7.3.4.4.1
A BSCI Interactive Port Subscriber entry containing objects relating to the port that are configurable by the user.
OBJECT-TYPE    
  BsciSubscrOperEntry  

bsciSubscrOperSequence 1.3.6.1.4.1.173.7.3.4.4.1.1
Subscriber index for a specific BSCI port subscriber.
OBJECT-TYPE    
  INTEGER 1..16  

bsciSubscrOperLocalID 1.3.6.1.4.1.173.7.3.4.4.1.2
Subscriber address of the local end of a BSCI connection.
OBJECT-TYPE    
  NlSubscriberAddress  

bsciSubscrOperRemoteID 1.3.6.1.4.1.173.7.3.4.4.1.3
Subscriber address of the remote end of a BSCI connection.
OBJECT-TYPE    
  NlSubscriberAddress  

bsciSubscrOperAutocall 1.3.6.1.4.1.173.7.3.4.4.1.4
Causes a BSCI TPAD to automatically call its HPAD when the controller becomes active.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

bsciSubscrOperAutocallRtyTimer 1.3.6.1.4.1.173.7.3.4.4.1.5
Time between autocall retries.
OBJECT-TYPE    
  INTEGER 15..255  

bsciSubscrOperAutocallMaxRtry 1.3.6.1.4.1.173.7.3.4.4.1.6
Maximum number of times an autocall will be sent.
OBJECT-TYPE    
  INTEGER 0..255  

bsciSubscrOperConnectionID 1.3.6.1.4.1.173.7.3.4.4.1.7
Identifier that will link the BSCI port with a device configured in the BSCI Devices Table.
OBJECT-TYPE    
  INTEGER 0..255  

bsciDevAdminTable 1.3.6.1.4.1.173.7.3.4.5
A list of BSC Interactive devices.
OBJECT-TYPE    
  SEQUENCE OF  
    BsciDevAdminEntry

bsciDevAdminEntry 1.3.6.1.4.1.173.7.3.4.5.1
A BSCI Interactive Device entry containing objects relating to the device that are configurable by the user.
OBJECT-TYPE    
  BsciDevAdminEntry  

bsciDevAdminControlUnitID 1.3.6.1.4.1.173.7.3.4.5.1.1
Control Unit identifier.
OBJECT-TYPE    
  INTEGER 0..31  

bsciDevAdminDeviceUnitID 1.3.6.1.4.1.173.7.3.4.5.1.2
Device Unit identifier.
OBJECT-TYPE    
  INTEGER 0..31  

bsciDevAdminConnectionID 1.3.6.1.4.1.173.7.3.4.5.1.3
The BSCI port connection ID for the device.
OBJECT-TYPE    
  INTEGER 0..255  

bsciDevAdminSingleUserVC 1.3.6.1.4.1.173.7.3.4.5.1.4
Specifies whether each end of the connection is within a same Control Unit/Device Type pair.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

bsciDevAdminTransTextSupported 1.3.6.1.4.1.173.7.3.4.5.1.5
Causes all characters transmitted to be treated as data.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

bsciDevAdminPrinterAttached 1.3.6.1.4.1.173.7.3.4.5.1.6
Specifies whether the device has a printer attached.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

bsciDevAdminRowStatus 1.3.6.1.4.1.173.7.3.4.5.1.7
This variable is used to manage the creation and deletion of conceptual rows in the bsciDevAdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

bsciDevAdminDisableStatusRequest 1.3.6.1.4.1.173.7.3.4.5.1.8
Determines how the BSCI port will report the status of the attached device. Normal status- the port will report what the device reports. No status- the port will report status only if the device is active. Always active status- the port will always report the device as active.
OBJECT-TYPE    
  INTEGER normal(1), none(2), always-active(3)  

bsciDevOperTable 1.3.6.1.4.1.173.7.3.4.6
A list of BSC Interactive devices.
OBJECT-TYPE    
  SEQUENCE OF  
    BsciDevOperEntry

bsciDevOperEntry 1.3.6.1.4.1.173.7.3.4.6.1
A BSCI Interactive Device entry containing objects relating to the device that are configurable by the user.
OBJECT-TYPE    
  BsciDevOperEntry  

bsciDevOperControlUnitID 1.3.6.1.4.1.173.7.3.4.6.1.1
Control Unit identifier.
OBJECT-TYPE    
  INTEGER 0..31  

bsciDevOperDeviceUnitID 1.3.6.1.4.1.173.7.3.4.6.1.2
Device Unit identifier.
OBJECT-TYPE    
  INTEGER 0..31  

bsciDevOperConnectionID 1.3.6.1.4.1.173.7.3.4.6.1.3
The BSCI port connection ID for the device.
OBJECT-TYPE    
  INTEGER 0..255  

bsciDevOperSingleUserVC 1.3.6.1.4.1.173.7.3.4.6.1.4
Specifies whether each end of the connection is within a same Control Unit/Device Type pair.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

bsciDevOperTransTextSupported 1.3.6.1.4.1.173.7.3.4.6.1.5
Causes all characters transmitted to be treated as data.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

bsciDevOperPrinterAttached 1.3.6.1.4.1.173.7.3.4.6.1.6
Specifies whether the device has a printer attached.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

bsciDevOperDisableStatusRequest 1.3.6.1.4.1.173.7.3.4.6.1.7
Determines how the BSCI port will report the status of the attached device. Normal status- the port will report what the device reports. No status- the port will report status only if the device is active. Always active status- the port will always report the device as active.
OBJECT-TYPE    
  INTEGER normal(1), none(2), always-active(3)  

portSdlcGroup 1.3.6.1.4.1.173.7.3.5
OBJECT IDENTIFIER    

portSdlcAdminTable 1.3.6.1.4.1.173.7.3.5.1
This table contains Netlink Enterprise specific objects to manage SDLC port. Changing on of the these parameters may take effect in the operating port immediately or may wait until the interface is restarted depending on the details of the implementation. Most of the objects in this read-write table have corresponding read-only objects in the portSdlcOperTable that return the current operating value. The operating values may be different from these configured values if a configured parameter was configured afterthe interface was started.
OBJECT-TYPE    
  SEQUENCE OF  
    PortSdlcAdminEntry

portSdlcAdminEntry 1.3.6.1.4.1.173.7.3.5.1.1
A list of configured values for an SDLC port.
OBJECT-TYPE    
  PortSdlcAdminEntry  

portSdlcAdminCommit 1.3.6.1.4.1.173.7.3.5.1.1.1
Writing a value to this object commits the the SDLC port related modified configuration values to the database.
OBJECT-TYPE    
  INTEGER  

portSdlcAdminMAXRetries 1.3.6.1.4.1.173.7.3.5.1.1.2
This object defines the max. number of retries to a non-responding Link station, before putting the Link station to slow-poll list if it is not Normal response Mode OR disconnecting the link station if it is data txfr state.
OBJECT-TYPE    
  INTEGER 0..99  

portSdlcAdminMAXOut 1.3.6.1.4.1.173.7.3.5.1.1.3
This object defines the number of outstanding frames for triggering window full condition.
OBJECT-TYPE    
  INTEGER 1..7  

portSdlcAdminPadType 1.3.6.1.4.1.173.7.3.5.1.1.4
This object defines the SNA PAD types.
OBJECT-TYPE    
  INTEGER xpad(1), tpad(2), hpad(3), npad(4)  

portSdlcAdminGenerateClock 1.3.6.1.4.1.173.7.3.5.1.1.5
This object defines if the port would generate clock.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portSdlcAdminRcvClockFromDTE 1.3.6.1.4.1.173.7.3.5.1.1.6
This object defines if the rcv clock will be used from DTE.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portSdlcAdminNrz 1.3.6.1.4.1.173.7.3.5.1.1.7
This object defines the data encoding at the physical layer
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portSdlcAdminPacketSize 1.3.6.1.4.1.173.7.3.5.1.1.8
This object defines the packet size of the X25 layer used by SNA PAD
OBJECT-TYPE    
  INTEGER 16..4096  

portSdlcAdminDisableRequestDisconnect 1.3.6.1.4.1.173.7.3.5.1.1.9
This object defines if a Request To Disconnect(RD) will be sent when remote PAD clear the connection
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portSdlcAdminLPDASupport 1.3.6.1.4.1.173.7.3.5.1.1.10
This object defines the type LPDA support on SDLC port.
OBJECT-TYPE    
  INTEGER none(1), lpda-1(2), lpda-2(3)  

portSdlcAdminConnector 1.3.6.1.4.1.173.7.3.5.1.1.11
This object defines the connector type of the SDLC port.
OBJECT-TYPE    
  INTEGER rs232(3), v35(5), rs449(6), rs530(7), x21(8), t1(10)  

portSdlcAdminSpeed 1.3.6.1.4.1.173.7.3.5.1.1.12
This object defines the speed of the SDLC port. The speed may only be set to one of a series of reasonable values, and if an attempt is made to set the speed to a value which is within the valid range but not equal to one of these values, the speed will be rounded up. If the connector type of the port is RS232, the port could be a standard port or a high speed port. If the port is a high speed RS232 port, the maximum valid speed is 256000. If the port is a standard RS232 port, the maximum valid speed is 64000 on the FRX4000/SS1840 and 19200 on all other products. It may be possible to set the speed of a standard RS232 port to a speed which is valid for a high speed RS232 port but invalid for a standard RS232 port. In this case, the port may not end up having the invalid speed. The default speed for a standard RS232 port on the FRX6000 is 19200.
OBJECT-TYPE    
  INTEGER 75..2048000  

portSdlcAdminRowStatus 1.3.6.1.4.1.173.7.3.5.1.1.13
This variable is used to manage the creation and deletion of conceptual rows in the portSdlcAdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

portSdlcAdminIdleFillChar 1.3.6.1.4.1.173.7.3.5.1.1.14
This object specifies a character that wll be inserted into the stream when the SNA link is idle.
OBJECT-TYPE    
  INTEGER hex-ff(1), hex-7e(2)  

portSdlcAdminInactivityTimer 1.3.6.1.4.1.173.7.3.5.1.1.15
This object determines how long the node will wait with no activity on the port before it will declare the attached device down.
OBJECT-TYPE    
  INTEGER 15..250  

portSdlcAdminL1Duplex 1.3.6.1.4.1.173.7.3.5.1.1.16
This object determines whether level-1 (physical layer) transmission can be in one (half duplex) or both (full duplex) directions at once.
OBJECT-TYPE    
  INTEGER full-duplex(1), half-duplex(2)  

portSdlcOperTable 1.3.6.1.4.1.173.7.3.5.2
This table contains current Netlink enterprise specific port parameters
OBJECT-TYPE    
  SEQUENCE OF  
    PortSdlcOperEntry

portSdlcOperEntry 1.3.6.1.4.1.173.7.3.5.2.1
A list of operational values for an SDLC port.
OBJECT-TYPE    
  PortSdlcOperEntry  

portSdlcOperCommit 1.3.6.1.4.1.173.7.3.5.2.1.1
This object is not used.
OBJECT-TYPE    
  INTEGER  

portSdlcOperMAXRetries 1.3.6.1.4.1.173.7.3.5.2.1.2
This object defines the max. number of retries to a non-responding Link station, before putting the Link station to slow-poll list if it is not Normal response Mode OR disconnecting the link station if it is data txfr state.
OBJECT-TYPE    
  INTEGER 0..99  

portSdlcOperMAXOut 1.3.6.1.4.1.173.7.3.5.2.1.3
This object defines the number of outstanding frames for triggering window full condition.
OBJECT-TYPE    
  INTEGER 1..7  

portSdlcOperPadType 1.3.6.1.4.1.173.7.3.5.2.1.4
This object defines the SNA PAD type
OBJECT-TYPE    
  INTEGER xpad(1), tpad(2), hpad(3), npad(4)  

portSdlcOperGenerateClock 1.3.6.1.4.1.173.7.3.5.2.1.5
This object defines if the port would generate clock.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portSdlcOperRcvClockFromDTE 1.3.6.1.4.1.173.7.3.5.2.1.6
This object defines if the rcv clock will be used from DTE.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portSdlcOperNrz 1.3.6.1.4.1.173.7.3.5.2.1.7
This object defines the data encoding at the physical layer
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portSdlcOperPacketSize 1.3.6.1.4.1.173.7.3.5.2.1.8
This object defines the packet size of the X25 layer used by SNA PAD
OBJECT-TYPE    
  INTEGER 16..4096  

portSdlcOperDisableRequestDisconnect 1.3.6.1.4.1.173.7.3.5.2.1.9
This object defines if a Request To Disconnect(RD) will be sent when remote PAD clear the connection
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portSdlcOperLPDASupport 1.3.6.1.4.1.173.7.3.5.2.1.10
This object defines the type LPDA support on SDLC port.
OBJECT-TYPE    
  INTEGER none(1), lpda-1(2), lpda-2(3)  

portSdlcOperConnector 1.3.6.1.4.1.173.7.3.5.2.1.11
This object defines the operational connector type of the SDLC port.
OBJECT-TYPE    
  INTEGER rs232(3), v35(5), rs449(6), rs530(7), x21(8), t1(10)  

portSdlcOperSpeed 1.3.6.1.4.1.173.7.3.5.2.1.12
This object defines the operational speed of the SDLC port.
OBJECT-TYPE    
  INTEGER  

portSdlcOperIdleFillChar 1.3.6.1.4.1.173.7.3.5.2.1.13
This object specifies a character that wll be inserted into the stream when the SNA link is idle.
OBJECT-TYPE    
  INTEGER hex-ff(1), hex-7e(2)  

portSdlcOperInactivityTimer 1.3.6.1.4.1.173.7.3.5.2.1.14
This object determines how long the node will wait with no activity on the port before it will declare the attached device down.
OBJECT-TYPE    
  INTEGER 15..250  

portSdlcOperL1Duplex 1.3.6.1.4.1.173.7.3.5.2.1.15
This object determines whether level-1 (physical layer) transmission can be in one (half duplex) or both (full duplex) directions at once.
OBJECT-TYPE    
  INTEGER full-duplex(1), half-duplex(2)  

lSSdlcAdminTable 1.3.6.1.4.1.173.7.3.5.3
This table contains Enterprise specific Link station configurable parameters to manage the link stations.
OBJECT-TYPE    
  SEQUENCE OF  
    LSSdlcAdminEntry

lSSdlcAdminEntry 1.3.6.1.4.1.173.7.3.5.3.1
A list of configured values for an SDLC port.
OBJECT-TYPE    
  LSSdlcAdminEntry  

lSSdlcAdminLocalSub 1.3.6.1.4.1.173.7.3.5.3.1.1
This object defines the local subscriber ID of the Link Station
OBJECT-TYPE    
  NlSubscriberAddress  

lSSdlcAdminRemoteSub 1.3.6.1.4.1.173.7.3.5.3.1.2
This object defines the remote subscriber ID used to connect to remote Link Station
OBJECT-TYPE    
  NlSubscriberAddress  

lSSdlcAdminAutoCall 1.3.6.1.4.1.173.7.3.5.3.1.3
This object defines if auto call is enabled for the link station. If enabled, the link station will initiate connection establishment, when appropriate. Else, it will passively listen to the connection request for establish a connection with the remote PAD
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

lSSdlcAdminRetryTime 1.3.6.1.4.1.173.7.3.5.3.1.4
This object is used, only when lSSdlcAdminAutoCall object is yes. This defines the time interval measured in seconds in which the connection request is retried
OBJECT-TYPE    
  INTEGER 15..225  

lSSdlcAdminRetryCount 1.3.6.1.4.1.173.7.3.5.3.1.5
This object is used, only when lSSdlcAdminAutoCall object is yes. This defines the number of times the connection initiation is retried before given up. The value of Zero(0) means to try indefinitely
OBJECT-TYPE    
  INTEGER 0..255  

lSSdlcAdminLlc2Conversion 1.3.6.1.4.1.173.7.3.5.3.1.6
This object defines if this link station connects to a LLC2 device/host.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

lSSdlcAdminLPDAResourceID 1.3.6.1.4.1.173.7.3.5.3.1.7
This objects the resource ID used during LPDA command support
OBJECT-TYPE    
  INTEGER 0..255  

lSSdlcAdminRowStatus 1.3.6.1.4.1.173.7.3.5.3.1.8
This variable is used to manage the creation and deletion of conceptual rows in the lSSdlcAdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned. Also note that deleting a PU entry will only remove it from the database file, and it's existence will still be known by the protocol until the node is rebooted or until an online update of the port is performed.
OBJECT-TYPE    
  RowStatus  

lSSdlcAdminL2DatMode 1.3.6.1.4.1.173.7.3.5.3.1.9
This object determines whether transmission can be in one (alternate) or two (simultaneous) directions at the same time.
OBJECT-TYPE    
  INTEGER two-way-alternate(1), two-way-simultaneous(2)  

lSSdlcOperTable 1.3.6.1.4.1.173.7.3.5.4
This table contains the operational parameters of the SDLC port
OBJECT-TYPE    
  SEQUENCE OF  
    LSSdlcOperEntry

lSSdlcOperEntry 1.3.6.1.4.1.173.7.3.5.4.1
A list of configured values for an SDLC port.
OBJECT-TYPE    
  LSSdlcOperEntry  

lSSdlcOperLocalSub 1.3.6.1.4.1.173.7.3.5.4.1.1
This object defines the local subscriber ID of the Link Station
OBJECT-TYPE    
  NlSubscriberAddress  

lSSdlcOperRemoteSub 1.3.6.1.4.1.173.7.3.5.4.1.2
This object defines the remote subscriber ID used to connect to remote Link Station
OBJECT-TYPE    
  NlSubscriberAddress  

lSSdlcOperAutoCall 1.3.6.1.4.1.173.7.3.5.4.1.3
This object defines if auto call is enabled for the link station. If enabled, the link station will initiate connection establishment, when appropriate. Else, it will passively listen to the connection request for establish a connection with the remote PAD
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

lSSdlcOperRetryTime 1.3.6.1.4.1.173.7.3.5.4.1.4
This object is valid, only when lSSdlcAdminAutoCall object is yes. This defines the time interval measured in seconds in which the connection request is retried
OBJECT-TYPE    
  INTEGER 15..225  

lSSdlcOperRetryCount 1.3.6.1.4.1.173.7.3.5.4.1.5
This object is used, only when lSSdlcAdminAutoCall object is yes. This defines the number of times the connection initiation is retried before given up. The value of Zero(0) means to try indefinitely
OBJECT-TYPE    
  INTEGER 0..255  

lSSdlcOperLlc2Conversion 1.3.6.1.4.1.173.7.3.5.4.1.6
This object defines if this link station connects to a LLC2 device/host.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

lSSdlcOperLPDAResourceID 1.3.6.1.4.1.173.7.3.5.4.1.7
This objects the resource ID used during LPDA command support
OBJECT-TYPE    
  INTEGER 0..255  

lSSdlcOperL2DatMode 1.3.6.1.4.1.173.7.3.5.4.1.8
This object determines whether transmission can be in one (alternate) or two (simultaneous) directions at the same time.
OBJECT-TYPE    
  INTEGER two-way-alternate(1), two-way-simultaneous(2)  

lSSdlcLlc2AdminTable 1.3.6.1.4.1.173.7.3.5.5
This table contains the LLC2 related parameters used to configure LLC2 session, when the SDLC station is connected to a LLC2 device at the remote end
OBJECT-TYPE    
  SEQUENCE OF  
    LSSdlcLlc2AdminEntry

lSSdlcLlc2AdminEntry 1.3.6.1.4.1.173.7.3.5.5.1
A list of configured values for an SDLC port.
OBJECT-TYPE    
  LSSdlcLlc2AdminEntry  

lSSdlcLlc2AdminLocalSap 1.3.6.1.4.1.173.7.3.5.5.1.1
This object defines Local SAP address (multiple of 4)
OBJECT-TYPE    
  INTEGER 0..252  

lSSdlcLlc2AdminLocalMac 1.3.6.1.4.1.173.7.3.5.5.1.2
This object defines the local MAC address
OBJECT-TYPE    
  PhysAddress  

lSSdlcLlc2AdminIdblk 1.3.6.1.4.1.173.7.3.5.5.1.3
This object defines idblk used in XID
OBJECT-TYPE    
  INTEGER 0..4095  

lSSdlcLlc2AdminIdnum 1.3.6.1.4.1.173.7.3.5.5.1.4
This object defines idnum used in XID
OBJECT-TYPE    
  INTEGER 0..1048575  

lSSdlcLlc2AdminLanTi 1.3.6.1.4.1.173.7.3.5.5.1.5
This object defines LLC2 inactivity timer measured in units of seconds
OBJECT-TYPE    
  INTEGER 1..50  

lSSdlcLlc2AdminLanT1 1.3.6.1.4.1.173.7.3.5.5.1.6
This object defines LLC2 reply timer measured in units of 100 milliseconds
OBJECT-TYPE    
  INTEGER 1..250  

lSSdlcLlc2AdminLanT2 1.3.6.1.4.1.173.7.3.5.5.1.7
This object defines Receiver Ack Timer measured in units of milliseconds
OBJECT-TYPE    
  INTEGER 100..5000  

lSSdlcLlc2AdminLanN2 1.3.6.1.4.1.173.7.3.5.5.1.8
This object defines Maximum Retransmissions
OBJECT-TYPE    
  INTEGER 0..255  

lSSdlcLlc2AdminLanN3 1.3.6.1.4.1.173.7.3.5.5.1.9
This object defines count of I-format LPDU's before sending Ack
OBJECT-TYPE    
  INTEGER 1..127  

lSSdlcLlc2AdminLanTw 1.3.6.1.4.1.173.7.3.5.5.1.10
This object defines Outstanding Frames
OBJECT-TYPE    
  INTEGER 1..127  

lSSdlcLlc2AdminBAG 1.3.6.1.4.1.173.7.3.5.5.1.11
This object defines bandwidth allocation group
OBJECT-TYPE    
  INTEGER 0..16  

lSSdlcLlc2AdminPriority 1.3.6.1.4.1.173.7.3.5.5.1.12
This object defines priority for traffic within the node
OBJECT-TYPE    
  INTEGER 0..9  

lSSdlcLlc2AdminRowStatus 1.3.6.1.4.1.173.7.3.5.5.1.13
This variable is used to manage the creation and deletion of conceptual rows in the lSSdlcLlc2AdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned. Also note that deleting a PU entry will only remove it from the database file, and it's existence will still be known by the protocol until the node is rebooted or until an online update of the port is performed.
OBJECT-TYPE    
  RowStatus  

lSSdlcLlc2AdminSuppressXID 1.3.6.1.4.1.173.7.3.5.5.1.14
This object prevents (if yes) the returning of an XID in response to a null XID. This might be desirable if the remote TPAD is not running PU 2.1. It should be noted that even if an XID is sent, an SNRM (Set Normal Response Mode) immediately follows, so the connection will be established.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

lSSdlcLlc2OperTable 1.3.6.1.4.1.173.7.3.5.6
This table contains operartional parameters related to LLC2 session of this link station.
OBJECT-TYPE    
  SEQUENCE OF  
    LSSdlcLlc2OperEntry

lSSdlcLlc2OperEntry 1.3.6.1.4.1.173.7.3.5.6.1
A list of configured values for an SDLC port.
OBJECT-TYPE    
  LSSdlcLlc2OperEntry  

lSSdlcLlc2OperLocalSap 1.3.6.1.4.1.173.7.3.5.6.1.1
This object defines Local SAP address (multiple of 4)
OBJECT-TYPE    
  INTEGER 0..252  

lSSdlcLlc2OperLocalMac 1.3.6.1.4.1.173.7.3.5.6.1.2
This object defines the local MAC address
OBJECT-TYPE    
  PhysAddress  

lSSdlcLlc2OperIdblk 1.3.6.1.4.1.173.7.3.5.6.1.3
This object defines idblk used in XID
OBJECT-TYPE    
  INTEGER 0..4095  

lSSdlcLlc2OperIdnum 1.3.6.1.4.1.173.7.3.5.6.1.4
This object defines idnum used in XID
OBJECT-TYPE    
  INTEGER 0..1048575  

lSSdlcLlc2OperLanTi 1.3.6.1.4.1.173.7.3.5.6.1.5
This object defines LLC2 inactivity timer measured in units of seconds
OBJECT-TYPE    
  INTEGER 1..50  

lSSdlcLlc2OperLanT1 1.3.6.1.4.1.173.7.3.5.6.1.6
This object defines LLC2 reply timer measured in units of 100 milliseconds
OBJECT-TYPE    
  INTEGER 1..250  

lSSdlcLlc2OperLanT2 1.3.6.1.4.1.173.7.3.5.6.1.7
This object defines Receiver Ack Timer measured in units of milliseconds
OBJECT-TYPE    
  INTEGER 100..5000  

lSSdlcLlc2OperLanN2 1.3.6.1.4.1.173.7.3.5.6.1.8
This object defines Maximum Retransmissions
OBJECT-TYPE    
  INTEGER 0..255  

lSSdlcLlc2OperLanN3 1.3.6.1.4.1.173.7.3.5.6.1.9
This object defines count of I-format LPDU's before sending Ack
OBJECT-TYPE    
  INTEGER 1..127  

lSSdlcLlc2OperLanTw 1.3.6.1.4.1.173.7.3.5.6.1.10
This object defines Outstanding Frames
OBJECT-TYPE    
  INTEGER 1..127  

lSSdlcLlc2OperBAG 1.3.6.1.4.1.173.7.3.5.6.1.11
This object defines bandwidth allocation group
OBJECT-TYPE    
  INTEGER 0..16  

lSSdlcLlc2OperPriority 1.3.6.1.4.1.173.7.3.5.6.1.12
This object defines priority for traffic within the node
OBJECT-TYPE    
  INTEGER 0..9  

lSSdlcLlc2OperSuppressXID 1.3.6.1.4.1.173.7.3.5.6.1.13
This object prevents (if yes) the returning of an XID in response to a null XID. This might be desirable if the remote TPAD is not running PU 2.1. It should be noted that even if an XID is sent, an SNRM (Set Normal Response Mode) immediately follows, so the connection will be established.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portT1Group 1.3.6.1.4.1.173.7.3.7
OBJECT IDENTIFIER    

portT1AdminTable 1.3.6.1.4.1.173.7.3.7.1
The configuration information pertaining to a T1 port. T1 ports can operate at full T1 bandwidth or DS0A channelized which provides 24 separate channels.
OBJECT-TYPE    
  SEQUENCE OF  
    PortT1AdminEntry

portT1AdminEntry 1.3.6.1.4.1.173.7.3.7.1.1
A T1 port entry containing objects relating to T1 ports.
OBJECT-TYPE    
  PortT1AdminEntry  

portT1AdminBlockedPortFlag 1.3.6.1.4.1.173.7.3.7.1.1.1
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portT1AdminGenerateClock 1.3.6.1.4.1.173.7.3.7.1.1.2
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portT1AdminFramingMode 1.3.6.1.4.1.173.7.3.7.1.1.3
Specifies how this T1 port is to function. ds0AT1 specifies a 24 channelized T1.
OBJECT-TYPE    
  INTEGER fullT1(1), ds0aT1(2)  

portT1AdminFrameModelSelect 1.3.6.1.4.1.173.7.3.7.1.1.4
OBJECT-TYPE    
  INTEGER d4(1), esf(2)  

portT1AdminLineEncoding 1.3.6.1.4.1.173.7.3.7.1.1.5
OBJECT-TYPE    
  INTEGER b8zs(1), ami(2)  

portT1AdminLineBuildOut 1.3.6.1.4.1.173.7.3.7.1.1.6
OBJECT-TYPE    
  INTEGER zerodb(1), x133-266ft(2), x266-399ft(3), x399-533ft(4), x533-655ft(5), minus7p5db(6), minus15db(7), minus22p5db(8)  

portT1AdminRowStatus 1.3.6.1.4.1.173.7.3.7.1.1.7
OBJECT-TYPE    
  RowStatus  

portT1AdminProtocolFraming 1.3.6.1.4.1.173.7.3.7.1.1.8
OBJECT-TYPE    
  INTEGER sync(1), bisync(2)  

portT1AdminNRZI 1.3.6.1.4.1.173.7.3.7.1.1.9
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portT1OperTable 1.3.6.1.4.1.173.7.3.7.2
The configuration information pertaining to a T1 port. T1 ports can operate at full T1 bandwidth or DS0A channelized which provides 24 separate channels.
OBJECT-TYPE    
  SEQUENCE OF  
    PortT1OperEntry

portT1OperEntry 1.3.6.1.4.1.173.7.3.7.2.1
A T1 port entry containing objects relating to T1 ports.
OBJECT-TYPE    
  PortT1OperEntry  

portT1OperBlockedPortFlag 1.3.6.1.4.1.173.7.3.7.2.1.1
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portT1OperGenerateClock 1.3.6.1.4.1.173.7.3.7.2.1.2
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portT1OperFramingMode 1.3.6.1.4.1.173.7.3.7.2.1.3
Specifies how this T1 port is to function. ds0AT1 specifies a 24 channelized T1.
OBJECT-TYPE    
  INTEGER fullT1(1), ds0aT1(2)  

portT1OperFrameModelSelect 1.3.6.1.4.1.173.7.3.7.2.1.4
OBJECT-TYPE    
  INTEGER d4(1), esf(2)  

portT1OperLineEncoding 1.3.6.1.4.1.173.7.3.7.2.1.5
OBJECT-TYPE    
  INTEGER b8zs(1), ami(2)  

portT1OperLineBuildOut 1.3.6.1.4.1.173.7.3.7.2.1.6
OBJECT-TYPE    
  INTEGER zerodb(1), x133-266ft(2), x266-399ft(3), x399-533ft(4), x533-655ft(5), minus7p5db(6), minus15db(7), minus22p5db(8)  

portT1OperProtocolFraming 1.3.6.1.4.1.173.7.3.7.2.1.7
OBJECT-TYPE    
  INTEGER sync(1), bisync(2)  

portT1OperNRZI 1.3.6.1.4.1.173.7.3.7.2.1.8
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portVoiceGroup 1.3.6.1.4.1.173.7.3.8
OBJECT IDENTIFIER    

portVoiceAdminTable 1.3.6.1.4.1.173.7.3.8.1
A list of Voice ports. The number of entries will be the number of Voice ports on the node.
OBJECT-TYPE    
  SEQUENCE OF  
    PortVoiceAdminEntry

portVoiceAdminEntry 1.3.6.1.4.1.173.7.3.8.1.1
A Voice Port entry containing objects relating to the port that are configurable by the user.
OBJECT-TYPE    
  PortVoiceAdminEntry  

portVoiceAdminRlpIndex 1.3.6.1.4.1.173.7.3.8.1.1.1
The RLP number of the Voice port.
OBJECT-TYPE    
  INTEGER  

portVoiceAdminPortIndex 1.3.6.1.4.1.173.7.3.8.1.1.2
The Port number of the Voice port.
OBJECT-TYPE    
  INTEGER  

portVoiceAdminBlockedFlag 1.3.6.1.4.1.173.7.3.8.1.1.3
The flag which causes the port to be enabled or disabled at node IPL. The port will remain in that state until this flag is changed and the node is rebooted, or until an on- line enable or disable is performed.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

portVoiceAdminSpeed 1.3.6.1.4.1.173.7.3.8.1.1.4
The speed of the port which is transmitted as part of a Call Setup frame. A Voice call will be established if there is enough bandwidth at each end to provide the minimum configured rate.
OBJECT-TYPE    
  INTEGER bps-4800(1), bps-8000(2), bps-32000(3), bps-64000(4)  

portVoiceAdminDTMF 1.3.6.1.4.1.173.7.3.8.1.1.5
The flag to enable, disable, or specify a time span over which DTMF (Dual Tone Multi Frequency) tones will be regenerated. 0 = pass tones transparently to the remote device. 1 = detect incoming tones and regenerate as received. 2-255 = regenerate tones for the specified seconds.
OBJECT-TYPE    
  INTEGER 0..255  

portVoiceAdminInterface 1.3.6.1.4.1.173.7.3.8.1.1.6
The type of interface (in conjunction with the Telephony Interface Type) that will be used by the Voice channel. This requires rebooting for the change to take effect. Telephony Type Interface Type -------------- -------------- OPX (FXO) Loop Start SLT (FXS) Loop Start E&M 4W E&M, 4W E&M TE, 2W E&M, 2W E&M TE AC15 AC15A, AC15C
OBJECT-TYPE    
  INTEGER em-4w(1), em-2w(2), loop-start(3), ac15-a(4), ac15-b(6), em-4w-te(10), em-2w-te(11)  

portVoiceAdminTETimer 1.3.6.1.4.1.173.7.3.8.1.1.7
The delay at which the E&M 'E' lead follows the 'M' lead.
OBJECT-TYPE    
  INTEGER 0..255  

portVoiceAdminLevelIn 1.3.6.1.4.1.173.7.3.8.1.1.8
The local voice level into the voice port. This adjusts the sensitivity of the local voice channel to the signal from the attached device. The purpose of this is to match the voice channel dB level to the input signal. A more negative setting produces a higher input gain. If the level is reduced, the voice channel will be more sensitive to the input. This will also cause the voice output at the remote device to sound louder.
OBJECT-TYPE    
  INTEGER -22..7  

portVoiceAdminLevelOut 1.3.6.1.4.1.173.7.3.8.1.1.9
The local voice level out of the voice port. A more positive setting produces a higher volume.
OBJECT-TYPE    
  INTEGER -22..7  

portVoiceAdminCallTimer 1.3.6.1.4.1.173.7.3.8.1.1.10
The amount of time the node will wait for a response to a Call Connect or Call Clear request. When the node issues a request, it will set a timer to the value configured here. If that timer expires with no response from the destination, the node will generate a busy tone.
OBJECT-TYPE    
  INTEGER 1..30  

portVoiceAdminHuntGroup 1.3.6.1.4.1.173.7.3.8.1.1.11
The hunt group that includes the voice channel.
OBJECT-TYPE    
  INTEGER none(1), a(2), b(3)  

portVoiceAdminLongDialPrefix 1.3.6.1.4.1.173.7.3.8.1.1.12
The character that will be required preceeding calls using the long call format. When the user at an attached device dials a long form number, it must be preceeded by the prefix character specified here.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

portVoiceAdminSLTTimeout 1.3.6.1.4.1.173.7.3.8.1.1.13
The time the local port will wait before an actual fax transmission begins. If there is no fax tone when this timer expires, the connection will be terminated.
OBJECT-TYPE    
  INTEGER 1..99  

portVoiceAdminLinkDownBusy 1.3.6.1.4.1.173.7.3.8.1.1.14
This flag enables or disables automatic busy-out of channels when the link is down. When enabled, the system will automatically busy-out channels when the composite link is down. When disabled, channels remain on-hook when the link is down. If your application is connected to a PBX that can route calls to another alternate source based on an all busy condition, enable this so the PBX will recognize this condition and reroute the calls while the composite link is down.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

portVoiceAdminFaxSupported 1.3.6.1.4.1.173.7.3.8.1.1.15
The flag to indicate whether or not faxes will be transmitted on the port. If no, all calls will be treated as voice. If yes, both voice and fax will be transmitted.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portVoiceAdminTelephonyType 1.3.6.1.4.1.173.7.3.8.1.1.16
The type of interface (in conjunction with the Interface Type) that will be used by the Voice channel. This requires rebooting for the change to take effect. Telephony Type Interface Type -------------- -------------- OPX (FXO) Loop Start SLT (FXS) Loop Start E&M 4W E&M, 4W E&M TE, 2W E&M, 2W E&M TE AC15 AC15A, AC15C
OBJECT-TYPE    
  INTEGER opx(1), slt(2), em(3), ac15(4)  

portVoiceAdminJitter 1.3.6.1.4.1.173.7.3.8.1.1.17
The amount of jitter delay.
OBJECT-TYPE    
  INTEGER 10..255  

portVoiceAdminSampleDelay 1.3.6.1.4.1.173.7.3.8.1.1.18
The amount of sample delay.
OBJECT-TYPE    
  INTEGER 0..255  

portVoiceAdminDialTimer 1.3.6.1.4.1.173.7.3.8.1.1.19
The delay the node will use to determine when variable length dialing is complete. (Variable length dialing allows the user to place a call without entering the configured number of digits for the speed dial number.)
OBJECT-TYPE    
  INTEGER 0..10  

portVoiceAdminAutoDial 1.3.6.1.4.1.173.7.3.8.1.1.20
The flag to enable or disable the auto dial feature. Note that enabling this feature will disable the variable length dialing feature for this channel.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

portVoiceAdminSuppression 1.3.6.1.4.1.173.7.3.8.1.1.21
The silence suppression level. A larger silence suppression level allows more data channels to operate simultaneously with the voice channels.
OBJECT-TYPE    
  INTEGER very-low(1), low(2), medium(3), high(4), very-high(5)  

portVoiceAdminAutoDialNumber 1.3.6.1.4.1.173.7.3.8.1.1.22
The number to which the node will attempt to connect when the handset attached to this port is taken off-hook. This is applicable only when the Auto Dial feature is enabled.
OBJECT-TYPE    
  OCTET STRING SIZE(0..4)  

portVoiceAdminAutoPoll 1.3.6.1.4.1.173.7.3.8.1.1.23
The flag to enable or disable auto polling. This is applicable only when the Auto Dial feature is enabled. When enabled, the node periodically polls the destination. If the poll is not acknowledged, the node will busy-out the channel. This can be useful in situations where the destination is an emergency number that must always be available. If the destination does not answer the automatic poll, the busy-out condition will notify an attached PBX that the emergency call should be routed to another call routing device.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

portVoiceAdminAutoPollTimer 1.3.6.1.4.1.173.7.3.8.1.1.24
The frequency with which an Auto Poll will be sent. This is applicable only when auto poll is enabled.
OBJECT-TYPE    
  INTEGER 5..30  

portVoiceAdminExtDigitsSource 1.3.6.1.4.1.173.7.3.8.1.1.25
The source of the extended digits when the user of attached equipment dials a speed dial number. This is applicable only when the number of extended dial digits is greater than zero. When map is specified, extended digits are taken from the extended digits field in the map table. When user is specified, extended digits are taken from the user of attached equipment.
OBJECT-TYPE    
  INTEGER map(1), user(2)  

portVoiceAdminNumDigitsDelete 1.3.6.1.4.1.173.7.3.8.1.1.26
The number of leading dial digits that will be deleted before a dial string is forwarded. This is primarily used to delete leading dial digits that may be inserted by an attached PBX.
OBJECT-TYPE    
  INTEGER 0..4  

portVoiceAdminForwardDelay 1.3.6.1.4.1.173.7.3.8.1.1.27
The length of a pause that can be inserted in an extended dial string that is being forwarded. This is applicable only when forwarded output digits is all or extended. When a comma is encountered in an extended digits string, the node will pause for the length of time specified here before additional extended digits are forwarded.
OBJECT-TYPE    
  INTEGER 0..40  

portVoiceAdminForwardedType 1.3.6.1.4.1.173.7.3.8.1.1.28
The method how the dial digits will be forwarded. This is applicable only when forwarded output digits is all or extended.
OBJECT-TYPE    
  INTEGER dtmf(1), pulse(2)  

portVoiceAdminForwardedDigits 1.3.6.1.4.1.173.7.3.8.1.1.29
The flag indicating which dial digits, if any, to forward. If none, dial digits are not forwarded to the destination device when a call is initiated on this channel. If all, the dialed speed dial number and associated extended digits are forwarded to the destination device. If extended, only the extended digit string is forwarded.
OBJECT-TYPE    
  INTEGER none(1), all(2), extended(3)  

portVoiceAdminMakeRatio 1.3.6.1.4.1.173.7.3.8.1.1.30
The make ratio of each digit pulse that is forwarded. This is applicable only when forwarded output digits is all or extended and forwarded digit type is pulse.
OBJECT-TYPE    
  INTEGER 20..80  

portVoiceAdminBreakRatio 1.3.6.1.4.1.173.7.3.8.1.1.31
The break ratio of each digit pulse that is forwarded. This is applicable only when forwarded output digits is all or extended and forwarded digit type is pulse.
OBJECT-TYPE    
  INTEGER 20..80  

portVoiceAdminDTMFOnDuration 1.3.6.1.4.1.173.7.3.8.1.1.32
The length of a tone that will be used to produce a single DTMF digit. This is applicable only when forwarded output digits is all or extended and forwarded digit type is DTMF.
OBJECT-TYPE    
  INTEGER 30..1000  

portVoiceAdminDTMFOffDuration 1.3.6.1.4.1.173.7.3.8.1.1.33
The length of silence between DTMF tones in a dial digit string. This is applicable only when forwarded output digits is all or extended and forwarded digit type is DTMF.
OBJECT-TYPE    
  INTEGER 30..1000  

portVoiceAdminToneType 1.3.6.1.4.1.173.7.3.8.1.1.34
The tone type to detect/regenerate for forwarding DTMF/MF.
OBJECT-TYPE    
  INTEGER dtmf(1), mf(2)  

portVoiceAdminRowStatus 1.3.6.1.4.1.173.7.3.8.1.1.35
This variable is used to manage the creation and deletion of conceptual rows in the portVoiceAdminTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device, and which is supplied by a management station wishing to exercise an on-line update of the existing conceptual row. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

portVoiceOperTable 1.3.6.1.4.1.173.7.3.8.2
A list of Voice ports. The number of entries will be the number of Voice ports on the node.
OBJECT-TYPE    
  SEQUENCE OF  
    PortVoiceOperEntry

portVoiceOperEntry 1.3.6.1.4.1.173.7.3.8.2.1
A Voice Port entry containing objects relating to the port that are configurable by the user.
OBJECT-TYPE    
  PortVoiceOperEntry  

portVoiceOperRlpIndex 1.3.6.1.4.1.173.7.3.8.2.1.1
The RLP number of the Voice port.
OBJECT-TYPE    
  INTEGER  

portVoiceOperPortIndex 1.3.6.1.4.1.173.7.3.8.2.1.2
The Port number of the Voice port.
OBJECT-TYPE    
  INTEGER  

portVoiceOperBlockedFlag 1.3.6.1.4.1.173.7.3.8.2.1.3
The flag which causes the port to be enabled or disabled at node IPL. The port will remain in that state until this flag is changed and the node is rebooted, or until an on- line enable or disable is performed.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

portVoiceOperSpeed 1.3.6.1.4.1.173.7.3.8.2.1.4
The speed of the port which is transmitted as part of a Call Setup frame. A Voice call will be established if there is enough bandwidth at each end to provide the minimum configured rate.
OBJECT-TYPE    
  INTEGER bps-4800(1), bps-8000(2), bps-32000(3), bps-64000(4)  

portVoiceOperDTMF 1.3.6.1.4.1.173.7.3.8.2.1.5
The flag to enable, disable, or specify a time span over which DTMF (Dual Tone Multi Frequency) tones will be regenerated. 0 = pass tones transparently to the remote device. 1 = detect incoming tones and regenerate as received. 2-255 = regenerate tones for the specified seconds.
OBJECT-TYPE    
  INTEGER 0..255  

portVoiceOperInterface 1.3.6.1.4.1.173.7.3.8.2.1.6
The type of interface (in conjunction with the Telephony Interface Type) that will be used by the Voice channel. This requires rebooting for the change to take effect. Telephony Type Interface Type -------------- -------------- OPX (FXO) Loop Start SLT (FXS) Loop Start E&M 4W E&M, 4W E&M TE, 2W E&M, 2W E&M TE AC15 AC15A, AC15C
OBJECT-TYPE    
  INTEGER em-4w(1), em-2w(2), loop-start(3), ac15-a(4), ac15-b(6), em-4w-te(10), em-2w-te(11)  

portVoiceOperTETimer 1.3.6.1.4.1.173.7.3.8.2.1.7
The delay at which the E&M 'E' lead follows the 'M' lead.
OBJECT-TYPE    
  INTEGER 0..255  

portVoiceOperLevelIn 1.3.6.1.4.1.173.7.3.8.2.1.8
The local voice level into the voice port. This adjusts the sensitivity of the local voice channel to the signal from the attached device. The purpose of this is to match the voice channel dB level to the input signal. A more negative setting produces a higher input gain. If the level is reduced, the voice channel will be more sensitive to the input. This will also cause the voice output at the remote device to sound louder.
OBJECT-TYPE    
  INTEGER -22..7  

portVoiceOperLevelOut 1.3.6.1.4.1.173.7.3.8.2.1.9
The local voice level out of the voice port. A more positive setting produces a higher volume.
OBJECT-TYPE    
  INTEGER -22..7  

portVoiceOperCallTimer 1.3.6.1.4.1.173.7.3.8.2.1.10
The amount of time the node will wait for a response to a Call Connect or Call Clear request. When the node issues a request, it will set a timer to the value configured here. If that timer expires with no response from the destination, the node will generate a busy tone.
OBJECT-TYPE    
  INTEGER 1..30  

portVoiceOperHuntGroup 1.3.6.1.4.1.173.7.3.8.2.1.11
The hunt group that includes the voice channel.
OBJECT-TYPE    
  INTEGER none(1), a(2), b(3)  

portVoiceOperLongDialPrefix 1.3.6.1.4.1.173.7.3.8.2.1.12
The character that will be required preceeding calls using the long call format. When the user at an attached device dials a long form number, it must be preceeded by the prefix character specified here.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

portVoiceOperSLTTimeout 1.3.6.1.4.1.173.7.3.8.2.1.13
The time the local port will wait before an actual fax transmission begins. If there is no fax tone when this timer expires, the connection will be terminated.
OBJECT-TYPE    
  INTEGER 1..99  

portVoiceOperLinkDownBusy 1.3.6.1.4.1.173.7.3.8.2.1.14
This flag enables or disables automatic busy-out of channels when the link is down. When enabled, the system will automatically busy-out channels when the composite link is down. When disabled, channels remain on-hook when the link is down. If your application is connected to a PBX that can route calls to another alternate source based on an all busy condition, enable this so the PBX will recognize this condition and reroute the calls while the composite link is down.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

portVoiceOperFaxSupported 1.3.6.1.4.1.173.7.3.8.2.1.15
The flag to indicate whether or not faxes will be transmitted on the port. If no, all calls will be treated as voice. If yes, both voice and fax will be transmitted.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portVoiceOperTelephonyType 1.3.6.1.4.1.173.7.3.8.2.1.16
The type of interface (in conjunction with the Interface Type) that will be used by the Voice channel. This requires rebooting for the change to take effect. Telephony Type Interface Type -------------- -------------- OPX (FXO) Loop Start SLT (FXS) Loop Start E&M 4W E&M, 4W E&M TE, 2W E&M, 2W E&M TE AC15 AC15A, AC15C
OBJECT-TYPE    
  INTEGER opx(1), slt(2), em(3), ac15(4)  

portVoiceOperJitter 1.3.6.1.4.1.173.7.3.8.2.1.17
The amount of jitter delay.
OBJECT-TYPE    
  INTEGER 10..255  

portVoiceOperSampleDelay 1.3.6.1.4.1.173.7.3.8.2.1.18
The amount of sample delay.
OBJECT-TYPE    
  INTEGER 0..255  

portVoiceOperDialTimer 1.3.6.1.4.1.173.7.3.8.2.1.19
The delay the node will use to determine when variable length dialing is complete. (Variable length dialing allows the user to place a call without entering the configured number of digits for the speed dial number.)
OBJECT-TYPE    
  INTEGER 0..10  

portVoiceOperAutoDial 1.3.6.1.4.1.173.7.3.8.2.1.20
The flag to enable or disable the auto dial feature. Note that enabling this feature will disable the variable length dialing feature for this channel.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

portVoiceOperSuppression 1.3.6.1.4.1.173.7.3.8.2.1.21
The silence suppression level. A larger silence suppression level allows more data channels to operate simultaneously with the voice channels.
OBJECT-TYPE    
  INTEGER very-low(1), low(2), medium(3), high(4), very-high(5)  

portVoiceOperAutoDialNumber 1.3.6.1.4.1.173.7.3.8.2.1.22
The number to which the node will attempt to connect when the handset attached to this port is taken off-hook. This is applicable only when the Auto Dial feature is enabled.
OBJECT-TYPE    
  OCTET STRING SIZE(0..4)  

portVoiceOperAutoPoll 1.3.6.1.4.1.173.7.3.8.2.1.23
The flag to enable or disable auto polling. This is applicable only when the Auto Dial feature is enabled. When enabled, the node periodically polls the destination. If the poll is not acknowledged, the node will busy-out the channel. This can be useful in situations where the destination is an emergency number that must always be available. If the destination does not answer the automatic poll, the busy-out condition will notify an attached PBX that the emergency call should be routed to another call routing device.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

portVoiceOperAutoPollTimer 1.3.6.1.4.1.173.7.3.8.2.1.24
The frequency with which an Auto Poll will be sent. This is applicable only when auto poll is enabled.
OBJECT-TYPE    
  INTEGER 5..30  

portVoiceOperExtDigitsSource 1.3.6.1.4.1.173.7.3.8.2.1.25
The source of the extended digits when the user of attached equipment dials a speed dial number. This is applicable only when the number of extended dial digits is greater than zero. When map is specified, extended digits are taken from the extended digits field in the map table. When user is specified, extended digits are taken from the user of attached equipment.
OBJECT-TYPE    
  INTEGER map(1), user(2)  

portVoiceOperNumDigitsDelete 1.3.6.1.4.1.173.7.3.8.2.1.26
The number of leading dial digits that will be deleted before a dial string is forwarded. This is primarily used to delete leading dial digits that may be inserted by an attached PBX.
OBJECT-TYPE    
  INTEGER 0..4  

portVoiceOperForwardDelay 1.3.6.1.4.1.173.7.3.8.2.1.27
The length of a pause that can be inserted in an extended dial string that is being forwarded. This is applicable only when forwarded output digits is all or extended. When a comma is encountered in an extended digits string, the node will pause for the length of time specified here before additional extended digits are forwarded.
OBJECT-TYPE    
  INTEGER 0..40  

portVoiceOperForwardedType 1.3.6.1.4.1.173.7.3.8.2.1.28
The method how the dial digits will be forwarded. This is applicable only when forwarded output digits is all or extended.
OBJECT-TYPE    
  INTEGER dtmf(1), pulse(2)  

portVoiceOperForwardedDigits 1.3.6.1.4.1.173.7.3.8.2.1.29
The flag indicating which dial digits, if any, to forward. If none, dial digits are not forwarded to the destination device when a call is initiated on this channel. If all, the dialed speed dial number and associated extended digits are forwarded to the destination device. If extended, only the extended digit string is forwarded.
OBJECT-TYPE    
  INTEGER none(1), all(2), extended(3)  

portVoiceOperMakeRatio 1.3.6.1.4.1.173.7.3.8.2.1.30
The make ratio of each digit pulse that is forwarded. This is applicable only when forwarded output digits is all or extended and forwarded digit type is pulse.
OBJECT-TYPE    
  INTEGER 20..80  

portVoiceOperBreakRatio 1.3.6.1.4.1.173.7.3.8.2.1.31
The break ratio of each digit pulse that is forwarded. This is applicable only when forwarded output digits is all or extended and forwarded digit type is pulse.
OBJECT-TYPE    
  INTEGER 20..80  

portVoiceOperDTMFOnDuration 1.3.6.1.4.1.173.7.3.8.2.1.32
The length of a tone that will be used to produce a single DTMF digit. This is applicable only when forwarded output digits is all or extended and forwarded digit type is DTMF.
OBJECT-TYPE    
  INTEGER 30..1000  

portVoiceOperDTMFOffDuration 1.3.6.1.4.1.173.7.3.8.2.1.33
The length of silence between DTMF tones in a dial digit string. This is applicable only when forwarded output digits is all or extended and forwarded digit type is DTMF.
OBJECT-TYPE    
  INTEGER 30..1000  

portVoiceOperToneType 1.3.6.1.4.1.173.7.3.8.2.1.34
The tone type to detect/regenerate for forwarding DTMF/MF.
OBJECT-TYPE    
  INTEGER dtmf(1), mf(2)  

nlInterfaces 1.3.6.1.4.1.173.7.4
OBJECT IDENTIFIER    

nlIfTable 1.3.6.1.4.1.173.7.4.1
A Table to describe each interface on a node. This table is indexed by RLP and Port number and can be used to identify the corresponding MIB-II ifIndex of a Port as well as additional port information maintained by Netlink.
OBJECT-TYPE    
  SEQUENCE OF  
    NlIfEntry

nlIfEntry 1.3.6.1.4.1.173.7.4.1.1
An Interface entry containing objects relating to interfaces.
OBJECT-TYPE    
  NlIfEntry  

nlIfRlp 1.3.6.1.4.1.173.7.4.1.1.1
The RLP number on the node. RLP numbers 1-8 are Physical RLP cards, and RLP number 250, 251 and 252 define IP, IPX and LLC2 interfaces respectively.
OBJECT-TYPE    
  INTEGER  

nlIfPort 1.3.6.1.4.1.173.7.4.1.1.2
The Port number on the RLP. Port numbers 1-8 are known to be physical ports, and 9-64 are logical ports. If the RLP number identifies an IP, IPX or LLC2 interface, then the port number can be 1-257 (IP), 1-64 (IPX), or 1-96 (LLC2).
OBJECT-TYPE    
  INTEGER  

nlIfType 1.3.6.1.4.1.173.7.4.1.1.3
The type of interface
OBJECT-TYPE    
  INTEGER other(1), regular1822(2), hdh1822(3), ddnX25(4), rfc877x25(5), ethernetCsmacd(6), iso88023Csmacd(7), iso88024TokenBus(8), iso88025TokenRing(9), iso88026Man(10), starLan(11), proteon10Mbit(12), proteon80Mbit(13), hyperchannel(14), fddi(15), lapb(16), sdlc(17), ds1(18), e1(19), basicISDN(20), primaryISDN(21), propPointToPointSerial(22), ppp(23), softwareLoopback(24), eon(25), ethernet3Mbit(26), nsip(27), slip(28), ultra(29), ds3(30), sip(31), frameRelay(32), rs232(33), para(34), arcnet(35), arcnetPlus(36), atm(37), miox25(38), sonet(39), x25ple(40), iso88022llc(41), localTalk(42), smdsDxi(43), frameRelayService(44), v35(45), hssi(46), hippi(47), modem(48), aal5(49), sonetPath(50), sonetVT(51), smdsIcip(52), propVirtual(53), propMultiplexor(54), trunk(200), async(201), bsci(202), logicalPort(203), t1(204), ip(205), ipx(206), llc2(207), voice(208)  

nlIfIndex 1.3.6.1.4.1.173.7.4.1.1.4
The associated index into the MIB-II ifTable for this port
OBJECT-TYPE    
  INTEGER  

nlIfTableIndex 1.3.6.1.4.1.173.7.4.1.1.5
The associated index into an enterprise table used to describe additional information for this port. See nlIfTableOid as the pointer to the actual table.
OBJECT-TYPE    
  INTEGER  

nlIfTableOid 1.3.6.1.4.1.173.7.4.1.1.6
The OID of the table Entry that contains additional information about this port. The OID will point to a specific table depending on the type of port.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

nlIfConnectorType 1.3.6.1.4.1.173.7.4.1.1.7
The physical connector type used for this port. Valid for ports 1-8 only.
OBJECT-TYPE    
  INTEGER none(2), rs232(3), v25bis-dial(4), v35(5), rs449(6), rs530(7), x21(8), csudsu(9), t1(10), e1(11), voice(13)  

nlIfPortStatus 1.3.6.1.4.1.173.7.4.1.1.8
The status of this port state. Valid for ports 1-64 only.
OBJECT-TYPE    
  INTEGER linkUp(1), restarting(2), operational(3), disabled(4), disconnect(5), configured(6), dialReady(7), quiesced(8), failed(9), hardwareFault(10), other(11), ipl(12), na(13), remoteLoopback(14), blueAlarm(15), yellowAlarm(16), redAlarm(17), onHook(18), offHook(19), dialing(20), activeVoiceCall(21), onHookPending(22)  

nlIfPhyPort 1.3.6.1.4.1.173.7.4.1.1.9
The Underlying Physical Port number on the RLP of this logical port. Port numbers 1-8 are valid, but this field is only applicable if the nlIfPort field is 9-64.
OBJECT-TYPE    
  INTEGER  

nlIfLlc2Interfaces 1.3.6.1.4.1.173.7.4.2
OBJECT IDENTIFIER    

nlIfLlc2LANTable 1.3.6.1.4.1.173.7.4.2.1
A Table to define LLC2 interfaces over LAN.
OBJECT-TYPE    
  SEQUENCE OF  
    NlIfLlc2LANEntry

nlIfLlc2LANEntry 1.3.6.1.4.1.173.7.4.2.1.1
An LLC2 LAN Interface entry containing objects relating to LLC2 LAN interfaces.
OBJECT-TYPE    
  NlIfLlc2LANEntry  

nlIfLlc2LANRlp 1.3.6.1.4.1.173.7.4.2.1.1.1
The RLP number on the node. For LLC2 LAN interfaces, this must be 252.
OBJECT-TYPE    
  INTEGER  

nlIfLlc2LANPort 1.3.6.1.4.1.173.7.4.2.1.1.2
The Port number on the RLP. For LLC2 LAN interfaces, this corresponds to the LAN card number.
OBJECT-TYPE    
  INTEGER  

nlIfLlc2LANType 1.3.6.1.4.1.173.7.4.2.1.1.3
The type of the LLC2 interface- either ethernet or token ring.
OBJECT-TYPE    
  INTEGER ethernet(1), token-ring(2)  

nlIfLlc2LANCard 1.3.6.1.4.1.173.7.4.2.1.1.4
The LAN card that the LLC2 interface is running on.
OBJECT-TYPE    
  INTEGER 1..2  

nlIfLlc2LANID 1.3.6.1.4.1.173.7.4.2.1.1.5
Valid only if the type of the LLC2 LAN interface is token ring. Identifies the token ring adapter to the network.
OBJECT-TYPE    
  INTEGER 0..4095  

nlIfLlc2LANInterface 1.3.6.1.4.1.173.7.4.2.1.1.6
The LLC2 interface number.
OBJECT-TYPE    
  INTEGER 1..2  

nlIfLlc2LANRowStatus 1.3.6.1.4.1.173.7.4.2.1.1.7
This variable is used to manage the creation and deletion of conceptual rows in the nlIfLlc2LANTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

nlIfLlc2LANPriority 1.3.6.1.4.1.173.7.4.2.1.1.8
Interface priority- allows setting a priority for traffic within the node. The higher the number, the higher the priority relative to other intra-nodal traffic.
OBJECT-TYPE    
  INTEGER 0..9  

nlIfLlc2LANBlockedPortFlag 1.3.6.1.4.1.173.7.4.2.1.1.9
The blocked port flag.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

nlIfLlc2FrTable 1.3.6.1.4.1.173.7.4.2.2
A Table to define LLC2 interfaces over Frame Relay.
OBJECT-TYPE    
  SEQUENCE OF  
    NlIfLlc2FrEntry

nlIfLlc2FrEntry 1.3.6.1.4.1.173.7.4.2.2.1
An LLC2 FR Interface entry containing objects relating to LLC2 FR interfaces.
OBJECT-TYPE    
  NlIfLlc2FrEntry  

nlIfLlc2FrRlp 1.3.6.1.4.1.173.7.4.2.2.1.1
The RLP number on the node.
OBJECT-TYPE    
  INTEGER 1..8  

nlIfLlc2FrPort 1.3.6.1.4.1.173.7.4.2.2.1.2
The Port number on the RLP. Port numbers 1-8 are known to be physical ports, and channels are 193-241.
OBJECT-TYPE    
  INTEGER 1..255  

nlIfLlc2FrDLCI 1.3.6.1.4.1.173.7.4.2.2.1.3
The DLCI number used to identify the entry in the table. The range is 16-991.
OBJECT-TYPE    
  INTEGER 16..991  

nlIfLlc2FrFormat 1.3.6.1.4.1.173.7.4.2.2.1.4
The RFC1490 encapsulation method used for LLC2 traffic.
OBJECT-TYPE    
  INTEGER native-llc2(1), tb-8023(2), srb-8025(3)  

nlIfLlc2FrPriority 1.3.6.1.4.1.173.7.4.2.2.1.5
Interface priority- allows setting a priority for traffic within the node. The higher the number, the higher the priority relative to other intra-nodal traffic.
OBJECT-TYPE    
  INTEGER 0..9  

nlIfLlc2FrBAG 1.3.6.1.4.1.173.7.4.2.2.1.6
Assigns the interface to one of sixteen groups whose parameters regulate bandwidth usage.
OBJECT-TYPE    
  INTEGER 1..16  

nlIfLlc2FrHostMACAddress 1.3.6.1.4.1.173.7.4.2.2.1.7
The MAC address of the host or workstation to which the remote device needs to connect. Valid only if the format is native-llc2.
OBJECT-TYPE    
  MacAddress  

nlIfLlc2FrSessionType 1.3.6.1.4.1.173.7.4.2.2.1.8
If originated, means that LLC2 connects from the configured Host MAC address can use this interface. If terminated, connections to the configured address can use this interface. Valid only if the format is native-llc2.
OBJECT-TYPE    
  INTEGER terminated(1), originated(2), not-applicable(3)  

nlIfLlc2FrLANID 1.3.6.1.4.1.173.7.4.2.2.1.9
Identifies the ring number used by a frame relay-compliant source-route bridge at the other end of this PVC. Valid only if the format is srb-8025.
OBJECT-TYPE    
  INTEGER 0..4095  

nlIfLlc2FrInterface 1.3.6.1.4.1.173.7.4.2.2.1.10
LLC2 interface number.
OBJECT-TYPE    
  INTEGER  

nlIfLlc2FrRowStatus 1.3.6.1.4.1.173.7.4.2.2.1.11
This variable is used to manage the creation and deletion of conceptual rows in the nlIfLlc2FrTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

nlIfLlc2FrBlockedPortFlag 1.3.6.1.4.1.173.7.4.2.2.1.12
The blocked port flag.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipxConfig 1.3.6.1.4.1.173.7.4.3
OBJECT IDENTIFIER    

ipxConfigRouting 1.3.6.1.4.1.173.7.4.3.1
OBJECT IDENTIFIER    

ipxStaticRouteConfigTable 1.3.6.1.4.1.173.7.4.3.1.1
The IPX Static Route Configuration Table
OBJECT-TYPE    
  SEQUENCE OF  
    IPXStaticRouteConfigEntry

ipxStaticRouteConfigEntry 1.3.6.1.4.1.173.7.4.3.1.1.1
Each entry corresponds to one instance of IPX Static Routing on the system
OBJECT-TYPE    
  IPXStaticRouteConfigEntry  

ipxStaticRouteConfigCircIndex 1.3.6.1.4.1.173.7.4.3.1.1.1.1
The unique identifier of the circuit used to reach the first hop in the static route
OBJECT-TYPE    
  INTEGER 1..65535  

ipxStaticRouteConfigNetNum 1.3.6.1.4.1.173.7.4.3.1.1.1.2
The IPX network number of the route's destination
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

ipxStaticRouteConfigRouter 1.3.6.1.4.1.173.7.4.3.1.1.1.3
The hex value of the node address of the router that will forward a packet when this route is used. If Novell's IPXWAN is used on the interface, this field will be ignored
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ipxStaticRouteConfigRowStatus 1.3.6.1.4.1.173.7.4.3.1.1.1.4
This variable is used to manage the creation and deletion of conceptual rows in the ipxStaticRouteTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

ipxServConfigTable 1.3.6.1.4.1.173.7.4.3.1.2
The IPX Static Route Configuration Table
OBJECT-TYPE    
  SEQUENCE OF  
    IPXServConfigEntry

ipxServConfigEntry 1.3.6.1.4.1.173.7.4.3.1.2.1
Each entry corresponds to one instance of IPX Static Routing on the system
OBJECT-TYPE    
  IPXServConfigEntry  

ipxServConfigServiceType 1.3.6.1.4.1.173.7.4.3.1.2.1.1
The Service Type, a SAP service code
OBJECT-TYPE    
  INTEGER 1..65535  

ipxServConfigServName 1.3.6.1.4.1.173.7.4.3.1.2.1.2
The Sercice Name, identifies a specific server in the IPX network.
OBJECT-TYPE    
  OCTET STRING SIZE(1..48)  

ipxServConfigServNetworkAddress 1.3.6.1.4.1.173.7.4.3.1.2.1.3
The IPX network number portion of the IPX address of the server identified by ServName
OBJECT-TYPE    
  INTEGER  

ipxServConfigServNodeAddress 1.3.6.1.4.1.173.7.4.3.1.2.1.4
The node portion of the IPX address of the service
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ipxServConfigServSocketNumber 1.3.6.1.4.1.173.7.4.3.1.2.1.5
The socket portion of the IPX address of the service
OBJECT-TYPE    
  INTEGER 0..65535  

ipxServConfigInterveningNetworks 1.3.6.1.4.1.173.7.4.3.1.2.1.6
The number of routers that a packet must pass through t reach the server
OBJECT-TYPE    
  INTEGER 1..65535  

ipxServConfigGatewayAddress 1.3.6.1.4.1.173.7.4.3.1.2.1.7
The node address of the router thar will forward a packet
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

ipxServConfigInterface 1.3.6.1.4.1.173.7.4.3.1.2.1.8
The IPX network number assigned to the interface used to send packets that are destined for this server
OBJECT-TYPE    
  INTEGER 0..65535  

ipxServConfigRowStatus 1.3.6.1.4.1.173.7.4.3.1.2.1.9
This variable is used to manage the creation and deletion of conceptual rows in the ipxServTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

ipxConfigInterface 1.3.6.1.4.1.173.7.4.3.2
OBJECT IDENTIFIER    

ipxInterfaceTable 1.3.6.1.4.1.173.7.4.3.2.6
The IPX Interface Table
OBJECT-TYPE    
  SEQUENCE OF  
    IPXInterfaceEntry

ipxInterfaceEntry 1.3.6.1.4.1.173.7.4.3.2.6.1
OBJECT-TYPE    
  IPXInterfaceEntry  

ipxInterfaceNumber 1.3.6.1.4.1.173.7.4.3.2.6.1.1
The Interface Number, a sequential number to identify the interface
OBJECT-TYPE    
  INTEGER 1..64  

ipxInterfaceBlockedPortFlag 1.3.6.1.4.1.173.7.4.3.2.6.1.2
This flag causes the IPX interface to be enabled (N) or disabled (Y) at node IPL. The port will remain in that state until this parameter is changed
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipxInterfaceType 1.3.6.1.4.1.173.7.4.3.2.6.1.3
The interface type. 802.5 is not valid on FRX4000
OBJECT-TYPE    
  INTEGER ethernet(1), eight025(2), x25(3), frl(4)  

ipxInterfaceFrameType 1.3.6.1.4.1.173.7.4.3.2.6.1.4
The frame type - depends on the interfece type. Valid combinations are: Ethernet, 802.5 - typeII, raw, llc, snap Frame relay, X25 - typeII
OBJECT-TYPE    
  INTEGER typeII(1), raw(2), llc(3), snap(4)  

ipxInterfaceMaxTransUnit 1.3.6.1.4.1.173.7.4.3.2.6.1.5
Maximum frame size that can be transmitted or received over the IPX interface.: Valid ranges are: Ethernet - (45-1518) 802.5 - (48-4096) Frame relay, X25 - (31-4096)
OBJECT-TYPE    
  INTEGER  

ipxInterfaceNetworkAddress 1.3.6.1.4.1.173.7.4.3.2.6.1.6
Identifies the local interface to the Novell Network
OBJECT-TYPE    
  INTEGER  

ipxInterfaceBandwidthAllocGroup 1.3.6.1.4.1.173.7.4.3.2.6.1.7
Assigns the IPX interface to one of sixteen groups whose parameters regulate bandwidth usage
OBJECT-TYPE    
  INTEGER 1..16  

ipxInterfacePortDiagEnabled 1.3.6.1.4.1.173.7.4.3.2.6.1.8
Enables/Disables the IPX interface's ability to handle Novell diagonistics packets
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipxInterfaceNetBIOSEnabled 1.3.6.1.4.1.173.7.4.3.2.6.1.9
Determines whether Novell-encapsulated NetBIOS frames received on the interface will be processed
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipxInterfaceNetBIOSHops 1.3.6.1.4.1.173.7.4.3.2.6.1.10
Maximum number of hops allowed for routing a Novell-encapsulated NetBIOS frame
OBJECT-TYPE    
  INTEGER 0..255  

ipxInterfacePeriodicRIPEnabled 1.3.6.1.4.1.173.7.4.3.2.6.1.11
Determines whether the node will originate periodic IPX Routing Information Protocol messages from this interface to inform the network that the route through this interface is viable
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipxInterfacePeriodicRIPTimer 1.3.6.1.4.1.173.7.4.3.2.6.1.12
This is the interval between the periodic IPX RIP broadcasts from this interface
OBJECT-TYPE    
  INTEGER 1..65535  

ipxInterfacePeriodicSAPEnabled 1.3.6.1.4.1.173.7.4.3.2.6.1.13
Determines whether the node will originate periodic IPX SAP messages from this interface to inform the network which SAP entries in the routing table are viable
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipxInterfacePeriodicSAPTimer 1.3.6.1.4.1.173.7.4.3.2.6.1.14
The interval between the periodic SAP broadcasts from this interface
OBJECT-TYPE    
  INTEGER 1..65535  

ipxInterfaceRIPEnabled 1.3.6.1.4.1.173.7.4.3.2.6.1.15
Datermines whether this interface will support RIP proceswsing
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipxInterfaceRIPAgeTimer 1.3.6.1.4.1.173.7.4.3.2.6.1.16
This is used to delete route entries in the routing information table. The timer starts/restarts each time an entry is created/updated. If the timer expires, the router will assume that the entry is no longer valid and the entry will be deleteda from the table
OBJECT-TYPE    
  INTEGER 0..65535  

ipxInterfaceRIPMaxSize 1.3.6.1.4.1.173.7.4.3.2.6.1.17
Maximum possible RIP packet size
OBJECT-TYPE    
  INTEGER 54..446  

ipxInterfaceSAPEnabled 1.3.6.1.4.1.173.7.4.3.2.6.1.18
Determines whether the interface will support SAP or not
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipxInterfaceSAPAgeTimer 1.3.6.1.4.1.173.7.4.3.2.6.1.19
This is used to delete route entries from the router information table. The timer starts/restars each time an entry is created/updated. If the timer expires, the router will assume that the entry is no longer valid and the entry will be deleted from the table
OBJECT-TYPE    
  INTEGER 0..65535  

ipxInterfaceTransportTime 1.3.6.1.4.1.173.7.4.3.2.6.1.20
is the time (in 55 milliseconds unit) that will normally take to forward frames out of interface. Recommmended values are 1 for LAN interfaces and 30 for WAN interfaces. A value of 0 indicates that the back to back frame forwarding is acceptable. This time is used to calculate the least cost path during routing. If IPXWAMN is (Y), Transport time will be overridden by the value calculated by IPXWAN
OBJECT-TYPE    
  INTEGER 1..255  

ipxInterfaceSerializationEnabled 1.3.6.1.4.1.173.7.4.3.2.6.1.21
Determines whether NetWare file server serialization security frames will be forwarded on the interface. These broadcasts frames are used by Novell to hold informations regarding the licensing of the file server executables
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipxInterfaceWatchdogSpoofingEnabled 1.3.6.1.4.1.173.7.4.3.2.6.1.22
Determines whether this interface will be used by the local node to respond to (keep alive) messages on behalf of the client workstations. Novell servers periodically issue these messages to all clients to determine whether each client is still alive
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipxInterfaceLanCardNumber 1.3.6.1.4.1.173.7.4.3.2.6.1.23
The card number installed in an FRX6000. The first or only LAN card installed is always 0, and the second is card 1
OBJECT-TYPE    
  INTEGER 0..1  

ipxInterfaceWanEnabled 1.3.6.1.4.1.173.7.4.3.2.6.1.24
Determines whether Novell's IPXWAN protocol will be used on the interface. IPXWAN specifies a method for IPX routers to communicate across WAN links. FRX6000 and FRX4000 implement IPXWAN running over RFC 1490-complaint frame relay and RFC1356-complaint X.25
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(3)  

ipxInterfaceSourceSubscriber 1.3.6.1.4.1.173.7.4.3.2.6.1.25
Subscruber id that defines an IPX interface in the node, by associating itself with port 66 (a number reserved for the IPXinterface) on the RLP that has an IPX installed on it. .. Valid only for type X.25
OBJECT-TYPE    
  OCTET STRING SIZE(0..15)  

ipxInterfaceDestinationSubscriber 1.3.6.1.4.1.173.7.4.3.2.6.1.26
Subscriber ID associated with the physical X.25 port that will be used for the IPX interface . .. Valid only for type X.25
OBJECT-TYPE    
  OCTET STRING SIZE(0..15)  

ipxInterfaceSVCRetryTimer 1.3.6.1.4.1.173.7.4.3.2.6.1.27
The frequency with which calls will be placed to try to establish a connection .. Valid only for type X.25
OBJECT-TYPE    
  INTEGER 5..60  

ipxInterfaceSVCIdleTimer 1.3.6.1.4.1.173.7.4.3.2.6.1.28
is a period that an IPX connection can remain active with no traffic before the connection is cleared. .. Valid only for type X.25
OBJECT-TYPE    
  INTEGER 0..5  

ipxInterfaceMaxVC 1.3.6.1.4.1.173.7.4.3.2.6.1.29
This specifies a number of virtual circuits over which IPX traffic will be transmitted in parallel. .. Valid only for type X.25
OBJECT-TYPE    
  INTEGER 1..8  

ipxInterfacePVCConnection 1.3.6.1.4.1.173.7.4.3.2.6.1.30
Identifies this interface as one of a PVC. .. Valid only for type X.25
OBJECT-TYPE    
  INTEGER no(1), yes(2), not-applicable(3)  

ipxInterfaceSourceCard 1.3.6.1.4.1.173.7.4.3.2.6.1.31
Identifies the location of this end of the frame relay IPX interface. .. Valid only for frame relay
OBJECT-TYPE    
  INTEGER 0..7  

ipxInterfaceSourcePort 1.3.6.1.4.1.173.7.4.3.2.6.1.32
Identifies the location of this end of the frame relay IPX interface. .. Valid only for frame relay
OBJECT-TYPE    
  INTEGER 0..7  

ipxInterfaceSourceDLCI 1.3.6.1.4.1.173.7.4.3.2.6.1.33
Identifies the location of this end of the frame relay IPX interface. .. Valid only for frame relay
OBJECT-TYPE    
  INTEGER 16..991  

ipxInterfaceRowStatus 1.3.6.1.4.1.173.7.4.3.2.6.1.34
This variable is used to manage the creation and deletion of conceptual rows in the ipxInterfaceTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

ipxConfigNodeDefault 1.3.6.1.4.1.173.7.4.3.3
OBJECT IDENTIFIER    

ipxNodeDefaultConfigNetworkAddress 1.3.6.1.4.1.173.7.4.3.3.1
Identifies the node to the IPX network
OBJECT-TYPE    
  INTEGER  

ipxNodeDefaultConfigRIPSAPGap 1.3.6.1.4.1.173.7.4.3.3.2
The minimum delay between consecutive RIP and SAP transmissions
OBJECT-TYPE    
  INTEGER 0..100  

ipxNodeDefaultConfigRouterName 1.3.6.1.4.1.173.7.4.3.3.3
An unique identifier within the IPX network
OBJECT-TYPE    
  OCTET STRING SIZE(1..48)  

nlIfIpInterfaces 1.3.6.1.4.1.173.7.4.4
OBJECT IDENTIFIER    

nlIfIpTable 1.3.6.1.4.1.173.7.4.4.1
A Table to define IP interfaces over frame relay, X.25, or LAN (ethernet, 802.3, 802.5).
OBJECT-TYPE    
  SEQUENCE OF  
    NlIfIpEntry

nlIfIpEntry 1.3.6.1.4.1.173.7.4.4.1.1
An IP Interface entry containing objects relating to IP interfaces.
OBJECT-TYPE    
  NlIfIpEntry  

nlIfIpInterface 1.3.6.1.4.1.173.7.4.4.1.1.1
The interface number which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this number is NOT the same interface as defined by the same value of ifIndex.
OBJECT-TYPE    
  INTEGER 1..257  

nlIfIpMtu 1.3.6.1.4.1.173.7.4.4.1.1.2
The maximum size (in bytes) of the data field that can be used to encapsulate an IP datagram for transmission over the interface. If the interface type is LAN based, then the maximum size value cannot exceed 1500.
OBJECT-TYPE    
  INTEGER 1..4096  

nlIfIpNetworkMask 1.3.6.1.4.1.173.7.4.4.1.1.3
The mask used during routing to determine the portion of the address associated with the network.
OBJECT-TYPE    
  IpAddress  

nlIfIpRouteMetric 1.3.6.1.4.1.173.7.4.4.1.1.4
The number of network hops (network gateways in the overall path over the internet) associated with this interface.
OBJECT-TYPE    
  INTEGER 0..255  

nlIfIpICMPAddRoutes 1.3.6.1.4.1.173.7.4.4.1.1.5
The flag which indicates whether IP may add routes obtained by ICMP, whose error and control function is used to send re-direction options back to the source if problems are discovered.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

nlIfIpRIPDeltaUpdates 1.3.6.1.4.1.173.7.4.4.1.1.6
The frequency with which RIP messages will be sent to every neighbor node, containing any changes to the routing table that occurred since the last full update.
OBJECT-TYPE    
  INTEGER 10..300  

nlIfIpRIPFullUpdates 1.3.6.1.4.1.173.7.4.4.1.1.7
The frequency with which updates of the entire routing table will be sent to every neighbor node, via one or more RIP messages.
OBJECT-TYPE    
  INTEGER 10..300  

nlIfIpPriority 1.3.6.1.4.1.173.7.4.4.1.1.8
The priority setting for traffic within the node. The higher the number, the higher the priority relative to other intra-nodal traffic.
OBJECT-TYPE    
  INTEGER 0..9  

nlIfIpBAG 1.3.6.1.4.1.173.7.4.4.1.1.9
The bandwidth allocation group to which this interface is assigned to. This object is only valid when the interface type is frame relay or proprietary virtual.
OBJECT-TYPE    
  INTEGER 1..16  

nlIfIpType 1.3.6.1.4.1.173.7.4.4.1.1.10
The type of IP interface.
OBJECT-TYPE    
  INTEGER other(1), rfc877x25(5), ethernetCsmacd(6), iso88023Csmacd(7), iso88025TokenRing(9), frameRelay(32), propVirtual(53)  

nlIfIpSourceAddress 1.3.6.1.4.1.173.7.4.4.1.1.11
The IP address of the end-to-end sender.
OBJECT-TYPE    
  IpAddress  

nlIfIpDestAddress 1.3.6.1.4.1.173.7.4.4.1.1.12
The IP address of the end-to-end receiver. This object is only valid when the interface type is X.25 or proprietary virtual, or when the interface type is frame relay and the inverse ARP flag indicates disabled.
OBJECT-TYPE    
  IpAddress  

nlIfIpBroadcastAddress 1.3.6.1.4.1.173.7.4.4.1.1.13
The IP address that is used to send to all LAN hosts on the network. This object is only valid when the interface type is LAN based.
OBJECT-TYPE    
  IpAddress  

nlIfIpLANCard 1.3.6.1.4.1.173.7.4.4.1.1.14
The LAN card that contains the interface. This object is only valid when the interface type is LAN based.
OBJECT-TYPE    
  INTEGER 0..1  

nlIfIpSourceSub 1.3.6.1.4.1.173.7.4.4.1.1.15
The subscriber ID associated with the source IP interface port. This object is only valid when the interface type is X.25.
OBJECT-TYPE    
  NlSubscriberAddress  

nlIfIpDestSub 1.3.6.1.4.1.173.7.4.4.1.1.16
The subscriber ID associated with the destination IP interface port. This object is only valid when the interface type is X.25.
OBJECT-TYPE    
  NlSubscriberAddress  

nlIfIpSVCRetryTimer 1.3.6.1.4.1.173.7.4.4.1.1.17
The frequency with which calls will be placed to try to establish a connection. This object is only valid when the interface type is X.25.
OBJECT-TYPE    
  INTEGER 5..60  

nlIfIpSVCIdleTimer 1.3.6.1.4.1.173.7.4.4.1.1.18
The period that an IP connection remains active with no traffic before the connection is cleared. This object is only valid when the interface type is X.25.
OBJECT-TYPE    
  INTEGER 0..5  

nlIfIpMaxSVC 1.3.6.1.4.1.173.7.4.4.1.1.19
The number of virtual circuits over which IP traffic will be transmitted in parallel. This object is only valid when the interface type is X.25.
OBJECT-TYPE    
  INTEGER 1..8  

nlIfIpPVCConnection 1.3.6.1.4.1.173.7.4.4.1.1.20
The flag which indicates whether this interface is a PVC. This object is only valid when the interface type is X.25.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

nlIfIpSourceRlp 1.3.6.1.4.1.173.7.4.4.1.1.21
The RLP of the logical interface of this end of the frame relay link. This object is only valid when the interface type is frame relay.
OBJECT-TYPE    
  INTEGER 1..8  

nlIfIpSourcePort 1.3.6.1.4.1.173.7.4.4.1.1.22
The port of the logical interface of this end of the frame relay link. This object is only valid when the interface type is frame relay.
OBJECT-TYPE    
  INTEGER 1..8  

nlIfIpSourceDLCI 1.3.6.1.4.1.173.7.4.4.1.1.23
The DLCI of the logical interface of this end of the frame relay link. This object is only valid when the interface type is frame relay.
OBJECT-TYPE    
  INTEGER 16..991  

nlIfIpRIPSupport 1.3.6.1.4.1.173.7.4.4.1.1.24
The RIP support that is being run on the interface.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2), receive-only(3)  

nlIfIpInverseARP 1.3.6.1.4.1.173.7.4.4.1.1.25
The flag which indicates whether inverse ARP is enabled or disabled. This object is only valid when the interface type is frame relay.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

nlIfIpProxyARP 1.3.6.1.4.1.173.7.4.4.1.1.26
The flag which indicates whether proxy ARP is enabled or disabled. This object is only valid when the interface type is LAN based.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

nlIfIpUnnumberedIf 1.3.6.1.4.1.173.7.4.4.1.1.27
The flag which indicates whether this interface is an unnumbered interface (i.e., does not require a specific source IP address). This object is only valid when the interface type is frame relay or X.25.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

nlIfIpRowStatus 1.3.6.1.4.1.173.7.4.4.1.1.28
This variable is used to manage the creation and deletion of conceptual rows in the nlIfIpTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

nlIfIpSecondaryAddrTable 1.3.6.1.4.1.173.7.4.4.2
A Table to define secondary IP interfaces on a LAN (ethernet, 802.3, 802.5) interface.
OBJECT-TYPE    
  SEQUENCE OF  
    NlIfIpSecondaryAddrEntry

nlIfIpSecondaryAddrEntry 1.3.6.1.4.1.173.7.4.4.2.1
An IP Secondary Address entry containing objects relating to IP secondary addresses.
OBJECT-TYPE    
  NlIfIpSecondaryAddrEntry  

nlIfIpSecondaryAddrSequence 1.3.6.1.4.1.173.7.4.4.2.1.1
The maximum number of secondary IP addresses that may be configured on an interface.
OBJECT-TYPE    
  INTEGER 1..15  

nlIfIpSecondaryAddrNetworkMask 1.3.6.1.4.1.173.7.4.4.2.1.2
The mask used during routing to determine the portion of the address associated with the network.
OBJECT-TYPE    
  IpAddress  

nlIfIpSecondaryAddrRouteMetric 1.3.6.1.4.1.173.7.4.4.2.1.3
The number of network hops (network gateways in the overall path over the internet) associated with this interface.
OBJECT-TYPE    
  INTEGER 0..255  

nlIfIpSecondaryAddrSourceAddress 1.3.6.1.4.1.173.7.4.4.2.1.4
The IP address of the end-to-end sender.
OBJECT-TYPE    
  IpAddress  

nlIfIpSecondaryAddrBroadcastAddress 1.3.6.1.4.1.173.7.4.4.2.1.5
The IP address that is used to send to all LAN hosts on the network.
OBJECT-TYPE    
  IpAddress  

nlIfIpSecondaryAddrRIPSupport 1.3.6.1.4.1.173.7.4.4.2.1.6
The RIP support that is being run on the interface.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2), receive-only(3)  

nlIfIpSecondaryAddrRowStatus 1.3.6.1.4.1.173.7.4.4.2.1.7
This variable is used to manage the creation and deletion of conceptual rows in the nlIfIpSecondaryAddrTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

nlIfVoiceInterfaces 1.3.6.1.4.1.173.7.4.5
OBJECT IDENTIFIER    

nlIfVoiceTable 1.3.6.1.4.1.173.7.4.5.1
A Table to define Voice interfaces over frame relay.
OBJECT-TYPE    
  SEQUENCE OF  
    NlIfVoiceEntry

nlIfVoiceEntry 1.3.6.1.4.1.173.7.4.5.1.1
A Voice Interface entry containing objects relating to the interface that are configurable by the user.
OBJECT-TYPE    
  NlIfVoiceEntry  

nlIfVoiceInterface 1.3.6.1.4.1.173.7.4.5.1.1.1
The interface number which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this number is NOT the same interface as defined by the same value of ifIndex.
OBJECT-TYPE    
  INTEGER 1..129  

nlIfVoicePeerNodeType 1.3.6.1.4.1.173.7.4.5.1.1.2
The node type for the node at the remote end of the frame relay connection.
OBJECT-TYPE    
  INTEGER netlink(1), act(2)  

nlIfVoicePeerNodeNumber 1.3.6.1.4.1.173.7.4.5.1.1.3
The node number of the remote device.
OBJECT-TYPE    
  INTEGER 1..61  

nlIfVoicePeerNodePort 1.3.6.1.4.1.173.7.4.5.1.1.4
The voice port on the remote device.
OBJECT-TYPE    
  INTEGER 1..17  

nlIfVoiceLocalNodeNumber 1.3.6.1.4.1.173.7.4.5.1.1.5
The node number of the local device.
OBJECT-TYPE    
  INTEGER 1..61  

nlIfVoiceLocalNodePort 1.3.6.1.4.1.173.7.4.5.1.1.6
The voice port on the local device.
OBJECT-TYPE    
  INTEGER 1..17  

nlIfVoiceFrameRelayRlp 1.3.6.1.4.1.173.7.4.5.1.1.7
The RLP of the logical interface of this end of the frame relay link.
OBJECT-TYPE    
  INTEGER 1..8  

nlIfVoiceFrameRelayPort 1.3.6.1.4.1.173.7.4.5.1.1.8
The port of the logical interface of this end of the frame relay link.
OBJECT-TYPE    
  INTEGER 1..8  

nlIfVoiceFrameRelayDLCI 1.3.6.1.4.1.173.7.4.5.1.1.9
The DLCI of the logical interface of this end of the frame relay link.
OBJECT-TYPE    
  INTEGER 16..991  

nlIfVoiceEnableFragment 1.3.6.1.4.1.173.7.4.5.1.1.10
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

nlIfVoiceRowStatus 1.3.6.1.4.1.173.7.4.5.1.1.11
This variable is used to manage the creation and deletion of conceptual rows in the noIfVoiceTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

subscriber 1.3.6.1.4.1.173.7.5
OBJECT IDENTIFIER    

nlLocalSubscriberTable 1.3.6.1.4.1.173.7.5.1
A Table to define each local subscriber.
OBJECT-TYPE    
  SEQUENCE OF  
    NlLocalSubscriberEntry

nlLocalSubscriberEntry 1.3.6.1.4.1.173.7.5.1.1
A Local Subscriber entry containing objects relating to local subscribers.
OBJECT-TYPE    
  NlLocalSubscriberEntry  

nlLocalSubscriberId 1.3.6.1.4.1.173.7.5.1.1.1
The Subscriber ID. A valid subscriber ID is a string of numeric digits represented by their ASCII equivalents. The ASCII equivalents of the wildcard characters '*' and '?' are also allowed. A '*' is a wildcard that matches any number of digits, including zero. A '?' is a wildcard that matches any single digit.
OBJECT-TYPE    
  NlSubscriberAddress  

nlLocalSubscriberName 1.3.6.1.4.1.173.7.5.1.1.2
The Subscriber name. The subscriber name is not accessible from SNMP, and a blank string is always returned.
OBJECT-TYPE    
  DisplayString SIZE(0..31)  

nlLocalSubscriberAlgorithm 1.3.6.1.4.1.173.7.5.1.1.3
The Subscriber routing algorithm. The following 4 types of routing algorithms are supported. 1 - round robin selects ports specified cyclicly in numerical order according to the list of Redirection addresses. If the port is unreachable or congested, the call request is sent to the next port. 2. Alternate Route on Line Failure - selects the first port not in a failed state. If a connection is not made, the call will be cleared even if other ports are available. 3. Alternate Route on Line Busy - selects the first port that has LCN's available (not busy). If a port has failed, the next available port is selected. 4. Least LCN with throughput selects the line with the minumum loading, calculated by weight and number of LCN's in use. If use of a routing algorithm is not desired, accept the default and specify only one routing path.
OBJECT-TYPE    
  INTEGER round-robin(1), line-failed(2), line-busy(3), least-lcn(4)  

nlLocalSubscriberSystematicRedirect 1.3.6.1.4.1.173.7.5.1.1.4
Systematic Redirection.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

nlLocalSubscriberRedirectBusy 1.3.6.1.4.1.173.7.5.1.1.5
Redirect calls according to Redirection Addresses if the primary subscriber device is busy.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

nlLocalSubscriberRedirectOO 1.3.6.1.4.1.173.7.5.1.1.6
Redirect calls according to Redirection Addresses if the primary subscriber device is out of order.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

nlLocalSubscriberPriority 1.3.6.1.4.1.173.7.5.1.1.7
Allows setting a priority for traffic within the node.
OBJECT-TYPE    
  INTEGER 0..9  

nlLocalSubscriberRowStatus 1.3.6.1.4.1.173.7.5.1.1.8
This variable is used to manage the creation and deletion of conceptual rows in the nlLocalSubscriberTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

nlLocalSubscriberRouteTable 1.3.6.1.4.1.173.7.5.2
A Table to define local subscriber route paths.
OBJECT-TYPE    
  SEQUENCE OF  
    NlLocalSubscriberRouteEntry

nlLocalSubscriberRouteEntry 1.3.6.1.4.1.173.7.5.2.1
A Local Subscriber Route entry containing objects relating to local subscriber routes.
OBJECT-TYPE    
  NlLocalSubscriberRouteEntry  

nlLocalSubscriberRouteIndex 1.3.6.1.4.1.173.7.5.2.1.1
Route path index for a specific subscriber route path.
OBJECT-TYPE    
  INTEGER 1..8  

nlLocalSubscriberRouteConf 1.3.6.1.4.1.173.7.5.2.1.2
Flag to indicate if the LP/port routing path to the subscriber device is configured or not. This object is read- only. The route is always configured for an entry in the table.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

nlLocalSubscriberRouteLP 1.3.6.1.4.1.173.7.5.2.1.3
Instance of the LP that makes up the routing path
OBJECT-TYPE    
  INTEGER  

nlLocalSubscriberRoutePort 1.3.6.1.4.1.173.7.5.2.1.4
Instance of the port that makes up the routing path
OBJECT-TYPE    
  INTEGER  

nlLocalSubscriberRouteRowStatus 1.3.6.1.4.1.173.7.5.2.1.5
This variable is used to manage the creation and deletion of conceptual rows in the nlLocalSubscriberRouteTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

nlLocalSubscriberRedirTable 1.3.6.1.4.1.173.7.5.3
A Table to list local subscriber redirection addresses.
OBJECT-TYPE    
  SEQUENCE OF  
    NlLocalSubscriberRedirEntry

nlLocalSubscriberRedirEntry 1.3.6.1.4.1.173.7.5.3.1
A Local Subscriber Redirection Address entry containing objects relating to local subscriber redirection addresses.
OBJECT-TYPE    
  NlLocalSubscriberRedirEntry  

nlLocalSubscriberRedirIndex 1.3.6.1.4.1.173.7.5.3.1.1
Redirection entry index for a local subscriber.
OBJECT-TYPE    
  INTEGER 1..5  

nlLocalSubscriberRedirAddr 1.3.6.1.4.1.173.7.5.3.1.2
Subscriber redirection address.
OBJECT-TYPE    
  NlSubscriberAddress  

nlLocalSubscriberRedirRowStatus 1.3.6.1.4.1.173.7.5.3.1.3
This variable is used to manage the creation and deletion of conceptual rows in the nlLocalSubscriberRedirTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

llc2 1.3.6.1.4.1.173.7.6
OBJECT IDENTIFIER    

nlLlc2HostTable 1.3.6.1.4.1.173.7.6.1
A Table to define LLC2 host entries.
OBJECT-TYPE    
  SEQUENCE OF  
    NlLlc2HostEntry

nlLlc2HostEntry 1.3.6.1.4.1.173.7.6.1.1
An LLC2 Host entry containing objects relating to LLC2 hosts.
OBJECT-TYPE    
  NlLlc2HostEntry  

nlLlc2HostIndex 1.3.6.1.4.1.173.7.6.1.1.1
LLC2 Host Index
OBJECT-TYPE    
  INTEGER 1..251  

nlLlc2HostMACAddress 1.3.6.1.4.1.173.7.6.1.1.2
The LLC2 Host MAC Address.
OBJECT-TYPE    
  MacAddress  

nlLlc2HostSessionType 1.3.6.1.4.1.173.7.6.1.1.3
The mode in which the Host is operating
OBJECT-TYPE    
  INTEGER originated(1), terminated(2)  

nlLlc2HostT1ReplyTimer 1.3.6.1.4.1.173.7.6.1.1.4
Reply Timer used to detect a failure of the Remote node.
OBJECT-TYPE    
  TimeInterval 1..250  

nlLlc2HostT2RecvAckTimer 1.3.6.1.4.1.173.7.6.1.1.5
Receive Ack Timer used to delay sending an acknowledgement of a received information LPDU.
OBJECT-TYPE    
  TimeInterval 100..5000  

nlLlc2HostTiInactivityTimer 1.3.6.1.4.1.173.7.6.1.1.6
Timer used to detect inoperative condition of the remote link station or transmission medium.
OBJECT-TYPE    
  TimeInterval 1..50  

nlLlc2HostN3NumberLPDUs 1.3.6.1.4.1.173.7.6.1.1.7
The number of Information LPDUs that need to be received before an acknowledgement is sent.
OBJECT-TYPE    
  INTEGER 1..127  

nlLlc2HostTwNumberOutstanding 1.3.6.1.4.1.173.7.6.1.1.8
Maximum number of sequentially numbered information LPDUs that can be outstanding at any time.
OBJECT-TYPE    
  INTEGER 1..127  

nlLlc2HostN2ExpiredT1LPDUCount 1.3.6.1.4.1.173.7.6.1.1.9
Maximum number of LPDU retransmissions occur following the expiration of Timer T1.
OBJECT-TYPE    
  INTEGER 0..255  

nlLlc2HostPriority 1.3.6.1.4.1.173.7.6.1.1.10
Traffic priorities within the node.
OBJECT-TYPE    
  INTEGER 0..9  

nlLlc2HostBAG 1.3.6.1.4.1.173.7.6.1.1.11
Bandwidth Allocation group to which the LLC2 Host belongs. This object is read-only. Bandwidth allocation groups do not apply to LLC2 hosts.
OBJECT-TYPE    
  INTEGER 1..16  

nlLlc2HostRoutingSubscriberId 1.3.6.1.4.1.173.7.6.1.1.12
LLC2 hosts Routing Subscriber Id
OBJECT-TYPE    
  NlSubscriberAddress  

nlLlc2HostSrcMACAddressMask 1.3.6.1.4.1.173.7.6.1.1.13
LLC2 Host's Source MAC Address Mask
OBJECT-TYPE    
  MacAddress  

nlLlc2HostAccess 1.3.6.1.4.1.173.7.6.1.1.14
Specifies different type(s) of interface(s) that can be used for connections to a terminated host session.
OBJECT-TYPE    
  INTEGER lan(1), frameRelay(2), tokenRing(3), ethernet(4), all(5), not-applicable(6)  

nlLlc2HostRowStatus 1.3.6.1.4.1.173.7.6.1.1.15
Row status convention for LLC2 Host entry.
OBJECT-TYPE    
  RowStatus  

nlLlc2HostInterface 1.3.6.1.4.1.173.7.6.1.1.16
LLC2 interface number associated with this host entry, always 300 for non-FRX7000.
OBJECT-TYPE    
  INTEGER  

nlLlc2HostGroup 1.3.6.1.4.1.173.7.6.1.1.17
Traffic group associated with LLC2 interface, always 1 for non-FRX7000.
OBJECT-TYPE    
  INTEGER 1..4  

nlLlc2TermConnectionTable 1.3.6.1.4.1.173.7.6.2
A Table to describe LLC2 Terminated Host Connections.
OBJECT-TYPE    
  SEQUENCE OF  
    NlLlc2TermConnectionEntry

nlLlc2TermConnectionEntry 1.3.6.1.4.1.173.7.6.2.1
An LLC2 Terminated Host Connection entry containing objects relating to LLC2 terminated host connections.
OBJECT-TYPE    
  NlLlc2TermConnectionEntry  

nlLlc2TermConnectionSequence 1.3.6.1.4.1.173.7.6.2.1.1
LLC2 Host connection Sequence number
OBJECT-TYPE    
  INTEGER 1..16  

nlLlc2TermConnectionHSAP 1.3.6.1.4.1.173.7.6.2.1.2
Service Access point used to connect to the Host
OBJECT-TYPE    
  INTEGER 4..254  

nlLlc2TermConnectionLocalSubscriberId 1.3.6.1.4.1.173.7.6.2.1.3
LLC2 Host Connection's Local Subscriber Id
OBJECT-TYPE    
  NlSubscriberAddress  

nlLlc2TermConnectionRemoteSubscriberId 1.3.6.1.4.1.173.7.6.2.1.4
LLC2 Host Connection's Remote Subscriber Id
OBJECT-TYPE    
  NlSubscriberAddress  

nlLlc2TermConnectionRowStatus 1.3.6.1.4.1.173.7.6.2.1.5
This variable is used to manage the creation and deletion of conceptual rows in the nlLlc2TermConnectionTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

nlLlc2OrigConnectionTable 1.3.6.1.4.1.173.7.6.3
A Table to describe LLC2 Originated Host Connections.
OBJECT-TYPE    
  SEQUENCE OF  
    NlLlc2OrigConnectionEntry

nlLlc2OrigConnectionEntry 1.3.6.1.4.1.173.7.6.3.1
An LLC2 Originated Host Connection entry containing objects relating to LLC2 originated host connections.
OBJECT-TYPE    
  NlLlc2OrigConnectionEntry  

nlLlc2OrigConnectionSequence 1.3.6.1.4.1.173.7.6.3.1.1
LLC2 Host connection Sequence number
OBJECT-TYPE    
  INTEGER 1..16  

nlLlc2OrigConnectionHSAP 1.3.6.1.4.1.173.7.6.3.1.2
Service Access point used to connect to the Host
OBJECT-TYPE    
  INTEGER 4..254  

nlLlc2OrigConnectionType 1.3.6.1.4.1.173.7.6.3.1.3
Specifies Remote subscriber device type
OBJECT-TYPE    
  INTEGER sdlc(1), llc2(2)  

nlLlc2OrigConnectionLocalSubscriberId 1.3.6.1.4.1.173.7.6.3.1.4
LLC2 Host Connection's Local Subscriber Id
OBJECT-TYPE    
  NlSubscriberAddress  

nlLlc2OrigConnectionRemoteSubscriberId 1.3.6.1.4.1.173.7.6.3.1.5
LLC2 Host Connection's Remote Subscriber Id
OBJECT-TYPE    
  NlSubscriberAddress  

nlLlc2OrigConnectionIDBLK 1.3.6.1.4.1.173.7.6.3.1.6
This field is obsolete
OBJECT-TYPE    
  INTEGER  

nlLlc2OrigConnectionIDNUM 1.3.6.1.4.1.173.7.6.3.1.7
This field is obsolete
OBJECT-TYPE    
  INTEGER  

nlLlc2OrigConnectionMAXDATA 1.3.6.1.4.1.173.7.6.3.1.8
This field is obsolete
OBJECT-TYPE    
  INTEGER  

nlLlc2OrigConnectionMAXIN 1.3.6.1.4.1.173.7.6.3.1.9
This field is obsolete
OBJECT-TYPE    
  INTEGER  

nlLlc2OrigConnectionRowStatus 1.3.6.1.4.1.173.7.6.3.1.10
This variable is used to manage the creation and deletion of conceptual rows in the nlLlc2OrigConnectionTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

nlLlc2NextHostNumber 1.3.6.1.4.1.173.7.6.4
The host number to be used for the next created host record, always 1 on non-FRX7000.
OBJECT-TYPE    
  INTEGER  

status 1.3.6.1.4.1.173.7.7
OBJECT IDENTIFIER    

pinStatusTable 1.3.6.1.4.1.173.7.7.4
A Table to describe the status of each pin on a physical port. This table is indexed by RLP and Port
OBJECT-TYPE    
  SEQUENCE OF  
    PortPinEntry

portPinEntry 1.3.6.1.4.1.173.7.7.4.1
A port pin entry containing objects relating to ports.
OBJECT-TYPE    
  PortPinEntry  

portPinRlp 1.3.6.1.4.1.173.7.7.4.1.1
The RLP number on the node
OBJECT-TYPE    
  INTEGER  

portPinPort 1.3.6.1.4.1.173.7.7.4.1.2
The Port number on the RLP. Port numbers 0-7 are known to be physical ports.
OBJECT-TYPE    
  INTEGER  

portPinStatus 1.3.6.1.4.1.173.7.7.4.1.3
The status of all pins for this physical port. There is one octet value for each of the pins. Each octet value is defined as follows: 00 = unknown 01 = active 02 = inactive 03 = unused
OBJECT-TYPE    
  OCTET STRING  

statistics 1.3.6.1.4.1.173.7.8
OBJECT IDENTIFIER    

statGroup 1.3.6.1.4.1.173.7.8.1
OBJECT IDENTIFIER    

rlpStatsTable 1.3.6.1.4.1.173.7.8.1.2
A Table to describe Statistics on each RLP
OBJECT-TYPE    
  SEQUENCE OF  
    RlpStatsEntry

rlpStatsEntry 1.3.6.1.4.1.173.7.8.1.2.1
An RLP statistics entry containing objects relating to RLP statistics.
OBJECT-TYPE    
  RlpStatsEntry  

rlpStatsIndex 1.3.6.1.4.1.173.7.8.1.2.1.1
The RLP number
OBJECT-TYPE    
  INTEGER  

rlpStatsQMessages 1.3.6.1.4.1.173.7.8.1.2.1.2
The number of frames queued on the RLP
OBJECT-TYPE    
  Counter  

rlpStatsUsedBuffers 1.3.6.1.4.1.173.7.8.1.2.1.3
The percentage of total buffers available being used at the moment of inquiry
OBJECT-TYPE    
  Counter  

rlpStatsInFrames 1.3.6.1.4.1.173.7.8.1.2.1.4
The number of frames received.
OBJECT-TYPE    
  Counter  

rlpStatsOutFrames 1.3.6.1.4.1.173.7.8.1.2.1.5
The number of frames transmitted.
OBJECT-TYPE    
  Counter  

rlpStatsFrameRejects 1.3.6.1.4.1.173.7.8.1.2.1.6
The number of frames rejected.
OBJECT-TYPE    
  Counter  

rlpStatsFrameRetransmits 1.3.6.1.4.1.173.7.8.1.2.1.7
The number of frames retransmitted . If this value is consistently greater than zero and there are no other problems, then increase the retransmission parameter.
OBJECT-TYPE    
  Counter  

portStatsTable 1.3.6.1.4.1.173.7.8.1.3
A Table to describe Statistics on each RLP
OBJECT-TYPE    
  SEQUENCE OF  
    PortStatsEntry

portStatsEntry 1.3.6.1.4.1.173.7.8.1.3.1
A port statistics entry containing objects relating to port statistics.
OBJECT-TYPE    
  PortStatsEntry  

portStatsRlpIndex 1.3.6.1.4.1.173.7.8.1.3.1.1
The RLP number
OBJECT-TYPE    
  INTEGER  

portStatsIndex 1.3.6.1.4.1.173.7.8.1.3.1.2
The Port number
OBJECT-TYPE    
  INTEGER  

portStatsInFrames 1.3.6.1.4.1.173.7.8.1.3.1.3
The number of frames received.
OBJECT-TYPE    
  Counter  

portStatsOutFrames 1.3.6.1.4.1.173.7.8.1.3.1.4
The number of frames transmitted.
OBJECT-TYPE    
  Counter  

portStatsFrameRetrans 1.3.6.1.4.1.173.7.8.1.3.1.5
The number of frames retransmitted.
OBJECT-TYPE    
  Counter  

portStatsFCSErrors 1.3.6.1.4.1.173.7.8.1.3.1.6
The number of Frame Check Sequence (FCS) errors. A value consistently greater than zero indicates line probelms.
OBJECT-TYPE    
  Counter  

portStatsLogicalRejects 1.3.6.1.4.1.173.7.8.1.3.1.7
The sum of Rejects and Frame Rejects. A value consistently greater than zero indicates line probelms.
OBJECT-TYPE    
  Counter  

portStatsInPercentUtils 1.3.6.1.4.1.173.7.8.1.3.1.8
The ratio of non-flag characters to total characters being received by the port.
OBJECT-TYPE    
  Counter  

portStatsOutPercentUtils 1.3.6.1.4.1.173.7.8.1.3.1.9
The ration of non-flag characters to total characters being transmitted by the port.
OBJECT-TYPE    
  Counter  

statFrame 1.3.6.1.4.1.173.7.8.1.4
OBJECT IDENTIFIER    

frStatsTable 1.3.6.1.4.1.173.7.8.1.4.1
A Table to describe Frame Relay Frame Level Statistics on each Port
OBJECT-TYPE    
  SEQUENCE OF  
    FrStatsEntry

frStatsEntry 1.3.6.1.4.1.173.7.8.1.4.1.1
A frame relay port statistics entry containing objects relating to frame relay port statistics.
OBJECT-TYPE    
  FrStatsEntry  

frStatsRlpIndex 1.3.6.1.4.1.173.7.8.1.4.1.1.1
The RLP Number.
OBJECT-TYPE    
  INTEGER  

frStatsPortIndex 1.3.6.1.4.1.173.7.8.1.4.1.1.2
The Port number.
OBJECT-TYPE    
  INTEGER  

frStatsTxDEFrames 1.3.6.1.4.1.173.7.8.1.4.1.1.3
The number of frames transmitted on the port with the Discard Eligibility bit set.
OBJECT-TYPE    
  Counter  

frStatsRxDEFrames 1.3.6.1.4.1.173.7.8.1.4.1.1.4
The number of frames received on the port with the discard eligibility bit set.
OBJECT-TYPE    
  Counter  

frStatsTxFECNFrames 1.3.6.1.4.1.173.7.8.1.4.1.1.5
The of number of frames transmitted on the port with FECN.
OBJECT-TYPE    
  Counter  

frStatsRxFECNFrames 1.3.6.1.4.1.173.7.8.1.4.1.1.6
The number of frames received on the port with FECN.
OBJECT-TYPE    
  Counter  

frStatsTxBECNFrames 1.3.6.1.4.1.173.7.8.1.4.1.1.7
The number of frames transmitted on the port with BECN.
OBJECT-TYPE    
  Counter  

frStatsRxBECNFrames 1.3.6.1.4.1.173.7.8.1.4.1.1.8
The number of frames received on the port with BECN.
OBJECT-TYPE    
  Counter  

frStatsTxLMIFrames 1.3.6.1.4.1.173.7.8.1.4.1.1.9
The number of LMI frames transmitted on the port.
OBJECT-TYPE    
  Counter  

frStatsRxLMIFrames 1.3.6.1.4.1.173.7.8.1.4.1.1.10
The number of LMI frames received on the port.
OBJECT-TYPE    
  Counter  

frStatsTxANXDFrames 1.3.6.1.4.1.173.7.8.1.4.1.1.11
The number of AnnexD frames transmitted on the port
OBJECT-TYPE    
  Counter  

frStatsRxANXDFrames 1.3.6.1.4.1.173.7.8.1.4.1.1.12
The number of AnnexD frames received on the port
OBJECT-TYPE    
  Counter  

frStatsTotDiscFrames 1.3.6.1.4.1.173.7.8.1.4.1.1.13
The total number of discarded frames on the port.
OBJECT-TYPE    
  Counter  

x25TxStatsTable 1.3.6.1.4.1.173.7.8.1.4.2
A Table to describe X25 Frame Level Txmit Statistics on each Port
OBJECT-TYPE    
  SEQUENCE OF  
    X25TxStatsEntry

x25TxStatsEntry 1.3.6.1.4.1.173.7.8.1.4.2.1
An X25 frame level transmit statistics entry containing objects relating to x25 frame level transmit statistics.
OBJECT-TYPE    
  X25TxStatsEntry  

x25TxRlpIndex 1.3.6.1.4.1.173.7.8.1.4.2.1.1
The RLP Number.
OBJECT-TYPE    
  INTEGER  

x25TxPortIndex 1.3.6.1.4.1.173.7.8.1.4.2.1.2
The Port number.
OBJECT-TYPE    
  INTEGER  

x25TxSABMFrames 1.3.6.1.4.1.173.7.8.1.4.2.1.3
The number of SABM's transmitted on the port.
OBJECT-TYPE    
  Counter  

x25TxUAFrames 1.3.6.1.4.1.173.7.8.1.4.2.1.4
The number of UA Frames transmitted on the port.
OBJECT-TYPE    
  Counter  

x25TxDISCFrames 1.3.6.1.4.1.173.7.8.1.4.2.1.5
The number of DISC Frames transmitted on the port.
OBJECT-TYPE    
  Counter  

x25TxDMFrames 1.3.6.1.4.1.173.7.8.1.4.2.1.6
The number of DM frames transmitted on the port.
OBJECT-TYPE    
  Counter  

x25TxFRMRFrames 1.3.6.1.4.1.173.7.8.1.4.2.1.7
The of Number of FRMR frames transmitted on the port.
OBJECT-TYPE    
  Counter  

x25TxREJFrames 1.3.6.1.4.1.173.7.8.1.4.2.1.8
The number of Reject Frames transmitted on the port.
OBJECT-TYPE    
  Counter  

x25TxRRFrames 1.3.6.1.4.1.173.7.8.1.4.2.1.9
The number of RR frames transmitted on the port.
OBJECT-TYPE    
  Counter  

x25TxRNRFrames 1.3.6.1.4.1.173.7.8.1.4.2.1.10
The number of RNR Frames transmitted on the port.
OBJECT-TYPE    
  Counter  

x25TxINFOFrames 1.3.6.1.4.1.173.7.8.1.4.2.1.11
The number of INFO Frames transmitted on the port
OBJECT-TYPE    
  Counter  

x25RxStatsTable 1.3.6.1.4.1.173.7.8.1.4.3
A Table to describe X25 Frame Level Rxmit Statistics on each Port
OBJECT-TYPE    
  SEQUENCE OF  
    X25RxStatsEntry

x25RxStatsEntry 1.3.6.1.4.1.173.7.8.1.4.3.1
An X25 frame level receive statistics entry containing objects relating to x25 frame level receive statistics.
OBJECT-TYPE    
  X25RxStatsEntry  

x25RxRlpIndex 1.3.6.1.4.1.173.7.8.1.4.3.1.1
The RLP Number.
OBJECT-TYPE    
  INTEGER  

x25RxPortIndex 1.3.6.1.4.1.173.7.8.1.4.3.1.2
The Port number.
OBJECT-TYPE    
  INTEGER  

x25RxSABMFrames 1.3.6.1.4.1.173.7.8.1.4.3.1.3
The number of SABM's received on the port.
OBJECT-TYPE    
  Counter  

x25RxUAFrames 1.3.6.1.4.1.173.7.8.1.4.3.1.4
The number of UA Frames received on the port.
OBJECT-TYPE    
  Counter  

x25RxDISCFrames 1.3.6.1.4.1.173.7.8.1.4.3.1.5
The number of DISC Frames received on the port.
OBJECT-TYPE    
  Counter  

x25RxDMFrames 1.3.6.1.4.1.173.7.8.1.4.3.1.6
The number of DM frames received on the port.
OBJECT-TYPE    
  Counter  

x25RxFRMRFrames 1.3.6.1.4.1.173.7.8.1.4.3.1.7
The of Number of FRMR frames received on the port.
OBJECT-TYPE    
  Counter  

x25RxREJFrames 1.3.6.1.4.1.173.7.8.1.4.3.1.8
The number of Reject Frames received on the port.
OBJECT-TYPE    
  Counter  

x25RxRRFrames 1.3.6.1.4.1.173.7.8.1.4.3.1.9
The number of RR frames received on the port.
OBJECT-TYPE    
  Counter  

x25RxRNRFrames 1.3.6.1.4.1.173.7.8.1.4.3.1.10
The number of RNR Frames received on the port.
OBJECT-TYPE    
  Counter  

x25RxINFOFrames 1.3.6.1.4.1.173.7.8.1.4.3.1.11
The number of INFO Frames received on the port
OBJECT-TYPE    
  Counter  

statBag 1.3.6.1.4.1.173.7.8.1.5
OBJECT IDENTIFIER    

statIp 1.3.6.1.4.1.173.7.8.1.6
OBJECT IDENTIFIER    

statT1 1.3.6.1.4.1.173.7.8.1.7
OBJECT IDENTIFIER    

t1StatsTable 1.3.6.1.4.1.173.7.8.1.7.1
A Table to describe T1 Statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    T1StatsEntry

t1StatsEntry 1.3.6.1.4.1.173.7.8.1.7.1.1
A T1 port statistics entry containing objects relating to T1 port statistics.
OBJECT-TYPE    
  T1StatsEntry  

t1StatsRlpIndex 1.3.6.1.4.1.173.7.8.1.7.1.1.1
The RLP Number.
OBJECT-TYPE    
  INTEGER  

t1StatsPortIndex 1.3.6.1.4.1.173.7.8.1.7.1.1.2
The Port Number.
OBJECT-TYPE    
  INTEGER  

t1StatsRcvFrames 1.3.6.1.4.1.173.7.8.1.7.1.1.3
Total received frames.
OBJECT-TYPE    
  Counter  

t1StatsXmitFrames 1.3.6.1.4.1.173.7.8.1.7.1.1.4
Total transmitted frames.
OBJECT-TYPE    
  Counter  

t1StatsLCVCnt 1.3.6.1.4.1.173.7.8.1.7.1.1.5
Line code violation count.
OBJECT-TYPE    
  Counter  

t1StatsPCVRErrs 1.3.6.1.4.1.173.7.8.1.7.1.1.6
PCVR Bit error count.
OBJECT-TYPE    
  Counter  

t1StatsOOSCnt 1.3.6.1.4.1.173.7.8.1.7.1.1.7
Multiframe out of sync count.
OBJECT-TYPE    
  Counter  

t1StatsBlueAlarms 1.3.6.1.4.1.173.7.8.1.7.1.1.8
Blue alarm count.
OBJECT-TYPE    
  Counter  

t1StatsYellowAlarms 1.3.6.1.4.1.173.7.8.1.7.1.1.9
Yellow alarm count.
OBJECT-TYPE    
  Counter  

t1StatsRedAlarms 1.3.6.1.4.1.173.7.8.1.7.1.1.10
Red alarm count.
OBJECT-TYPE    
  Counter  

t1StatsRcvUsage 1.3.6.1.4.1.173.7.8.1.7.1.1.11
Receive port utilization.
OBJECT-TYPE    
  Counter  

t1StatsXmitUsage 1.3.6.1.4.1.173.7.8.1.7.1.1.12
Transmit port utilization.
OBJECT-TYPE    
  Counter  

t1StatsXmitAbortFrames 1.3.6.1.4.1.173.7.8.1.7.1.1.13
Total aborted transmit frames.
OBJECT-TYPE    
  Counter  

t1StatsRcvAbortFrames 1.3.6.1.4.1.173.7.8.1.7.1.1.14
Total aborted receive frames.
OBJECT-TYPE    
  Counter  

t1StatsRcvOverruns 1.3.6.1.4.1.173.7.8.1.7.1.1.15
Total receive overruns.
OBJECT-TYPE    
  Counter  

t1StatsRcvErrors 1.3.6.1.4.1.173.7.8.1.7.1.1.16
Total bad receives.
OBJECT-TYPE    
  Counter  

t1StatsRcvChannelErrors 1.3.6.1.4.1.173.7.8.1.7.1.1.17
Total bad receives.
OBJECT-TYPE    
  Counter  

statDS0A 1.3.6.1.4.1.173.7.8.1.8
OBJECT IDENTIFIER    

ds0aStatsTable 1.3.6.1.4.1.173.7.8.1.8.1
A Table to describe DS0A Statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    DS0AStatsEntry

ds0aStatsEntry 1.3.6.1.4.1.173.7.8.1.8.1.1
A DS0A port statistics entry containing objects relating to DS0A port statistics.
OBJECT-TYPE    
  DS0AStatsEntry  

ds0aStatsRlpIndex 1.3.6.1.4.1.173.7.8.1.8.1.1.1
The RLP Number.
OBJECT-TYPE    
  INTEGER  

ds0aStatsPortIndex 1.3.6.1.4.1.173.7.8.1.8.1.1.2
The Port Number.
OBJECT-TYPE    
  INTEGER  

ds0aStatsChannelIndex 1.3.6.1.4.1.173.7.8.1.8.1.1.3
The Channel Number.
OBJECT-TYPE    
  INTEGER  

ds0aStatsXmitFrames 1.3.6.1.4.1.173.7.8.1.8.1.1.4
Total transmitted frames.
OBJECT-TYPE    
  Counter  

ds0aStatsRcvFrames 1.3.6.1.4.1.173.7.8.1.8.1.1.5
Total received frames.
OBJECT-TYPE    
  Counter  

ds0aStatsRcvAbortFrames 1.3.6.1.4.1.173.7.8.1.8.1.1.6
Total receive aborted frames.
OBJECT-TYPE    
  Counter  

ds0aStatsRcvOverruns 1.3.6.1.4.1.173.7.8.1.8.1.1.7
Total receive overruns.
OBJECT-TYPE    
  Counter  

ds0aStatsRcvErrors 1.3.6.1.4.1.173.7.8.1.8.1.1.8
Total receive errors.
OBJECT-TYPE    
  Counter  

statVoice 1.3.6.1.4.1.173.7.8.1.9
OBJECT IDENTIFIER    

voiceStatsTable 1.3.6.1.4.1.173.7.8.1.9.1
A Table to describe Voice over Frame Relay Statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    VoiceStatsEntry

voiceStatsEntry 1.3.6.1.4.1.173.7.8.1.9.1.1
A voice port statistics entry containing objects relating to voice port statistics.
OBJECT-TYPE    
  VoiceStatsEntry  

voiceStatsRlpIndex 1.3.6.1.4.1.173.7.8.1.9.1.1.1
The RLP Number.
OBJECT-TYPE    
  INTEGER  

voiceStatsPortIndex 1.3.6.1.4.1.173.7.8.1.9.1.1.2
The Port Number.
OBJECT-TYPE    
  INTEGER  

voiceStatsRxCalls 1.3.6.1.4.1.173.7.8.1.9.1.1.3
The Number of Calls Received from the Network.
OBJECT-TYPE    
  Counter  

voiceStatsTxCalls 1.3.6.1.4.1.173.7.8.1.9.1.1.4
The Number of Calls Transmitted to the Network.
OBJECT-TYPE    
  Counter  

voiceStatsRxCallsAccepts 1.3.6.1.4.1.173.7.8.1.9.1.1.5
The Number of Call Accepts Received from the Network.
OBJECT-TYPE    
  Counter  

voiceStatsTxCallsAccepts 1.3.6.1.4.1.173.7.8.1.9.1.1.6
The Number of Call Accepts Transmitted to the Network.
OBJECT-TYPE    
  Counter  

voiceStatsRxClears 1.3.6.1.4.1.173.7.8.1.9.1.1.7
The Number of Call Receives cleared.
OBJECT-TYPE    
  Counter  

voiceStatsTxClears 1.3.6.1.4.1.173.7.8.1.9.1.1.8
The Number of Call Transmitts cleared.
OBJECT-TYPE    
  Counter  

voiceStatsBusyCalls 1.3.6.1.4.1.173.7.8.1.9.1.1.9
The Number of calls which received Busy indication.
OBJECT-TYPE    
  Counter  

voiceStatsCallTimeouts 1.3.6.1.4.1.173.7.8.1.9.1.1.10
The Number of calls which transmitted time-out to the network.
OBJECT-TYPE    
  Counter  

voiceStatsRxCongestions 1.3.6.1.4.1.173.7.8.1.9.1.1.11
The number of congestion management frames Received.
OBJECT-TYPE    
  Counter  

voiceStatsTxCongestions 1.3.6.1.4.1.173.7.8.1.9.1.1.12
The number of congestion management frames Transmitted.
OBJECT-TYPE    
  Counter  

statThresh 1.3.6.1.4.1.173.7.8.2
OBJECT IDENTIFIER    

rlpThreshTable 1.3.6.1.4.1.173.7.8.2.1
A Table to describe Statistic thresholds on each RLP
OBJECT-TYPE    
  SEQUENCE OF  
    RlpThreshEntry

rlpThreshEntry 1.3.6.1.4.1.173.7.8.2.1.1
An RLP statistics threshold entry containing objects relating to RLP statistics thresholds.
OBJECT-TYPE    
  RlpThreshEntry  

rlpThreshRlpIndex 1.3.6.1.4.1.173.7.8.2.1.1.1
The RLP Number.
OBJECT-TYPE    
  INTEGER  

rlpThreshPercntBufInUse 1.3.6.1.4.1.173.7.8.2.1.1.2
The threshold for Percent of Buffers in use on the RLP
OBJECT-TYPE    
  INTEGER  

rlpThreshMsgQueueLen 1.3.6.1.4.1.173.7.8.2.1.1.3
The threshold for Percent of Buffers in use on the RLP
OBJECT-TYPE    
  INTEGER  

rlpThreshRxFramesPerSec 1.3.6.1.4.1.173.7.8.2.1.1.4
The threshold for Rcvd frames per second on the RLP
OBJECT-TYPE    
  INTEGER  

rlpThreshTxFramesPerSec 1.3.6.1.4.1.173.7.8.2.1.1.5
The threshold for Txmitted frames per second on the RLP
OBJECT-TYPE    
  INTEGER  

rlpThreshRejFramesPerSec 1.3.6.1.4.1.173.7.8.2.1.1.6
The threshold for Rejected Frames per second on the RLP
OBJECT-TYPE    
  INTEGER  

rlpThreshRtxFramesPerSec 1.3.6.1.4.1.173.7.8.2.1.1.7
The threshold for Retransmitted frames per second on the RLP
OBJECT-TYPE    
  INTEGER  

portThreshTable 1.3.6.1.4.1.173.7.8.2.2
A Table to describe Statistic thresholds on each port
OBJECT-TYPE    
  SEQUENCE OF  
    PortThreshEntry

portThreshEntry 1.3.6.1.4.1.173.7.8.2.2.1
A port statistics threshold entry containing objects relating to port statistics thresholds.
OBJECT-TYPE    
  PortThreshEntry  

portThreshRlpIndex 1.3.6.1.4.1.173.7.8.2.2.1.1
The RLP Number.
OBJECT-TYPE    
  INTEGER  

portThreshIndex 1.3.6.1.4.1.173.7.8.2.2.1.2
The Port Number.
OBJECT-TYPE    
  INTEGER  

portThreshRxFramesPerSec 1.3.6.1.4.1.173.7.8.2.2.1.3
The threshold for Rcvd frames per second on the port.
OBJECT-TYPE    
  INTEGER  

portThreshTxFramesPerSec 1.3.6.1.4.1.173.7.8.2.2.1.4
The threshold for Txmitted frames per second on the port.
OBJECT-TYPE    
  INTEGER  

portThreshRtxFramesPerSec 1.3.6.1.4.1.173.7.8.2.2.1.5
The threshold for Retransmitted frames per second on the port.
OBJECT-TYPE    
  INTEGER  

portThreshFCSErrPerSec 1.3.6.1.4.1.173.7.8.2.2.1.6
The threshold for FCS errors per second on the port.
OBJECT-TYPE    
  INTEGER  

portThreshLogRejPerSec 1.3.6.1.4.1.173.7.8.2.2.1.7
The threshold for Logical Rejects per second on the port.
OBJECT-TYPE    
  INTEGER  

portThreshTxErrorRatio 1.3.6.1.4.1.173.7.8.2.2.1.8
The threshold for Txmit error ratio on the port.
OBJECT-TYPE    
  INTEGER  

portThreshRxErrorRatio 1.3.6.1.4.1.173.7.8.2.2.1.9
The threshold for Rcv error ratio on the port.
OBJECT-TYPE    
  INTEGER  

portThreshTxPercentUtl 1.3.6.1.4.1.173.7.8.2.2.1.10
The threshold for Txmit percent utilization on the port.
OBJECT-TYPE    
  INTEGER  

portThreshRxPercentUtl 1.3.6.1.4.1.173.7.8.2.2.1.11
The threshold for Rcv percent utilization on the port.
OBJECT-TYPE    
  INTEGER  

bridge 1.3.6.1.4.1.173.7.9
OBJECT IDENTIFIER    

bridgeAdminVirtualLANID 1.3.6.1.4.1.173.7.9.1
LAN id inserted into token ring RIF field representing internal virtual ring, for LLC2 or bridged traffic
OBJECT-TYPE    
  INTEGER 0..4095  

bridgeOperVirtualLANID 1.3.6.1.4.1.173.7.9.2
LAN id inserted into token ring RIF field representing internal virtual ring, for LLC2 or bridged traffic
OBJECT-TYPE    
  INTEGER 0..4095  

bridgeEnabled 1.3.6.1.4.1.173.7.9.3
When yes the spanning tree algorithm is in effect and all traffic types may be bridged. When no only llc/2 terminated traffic is allowed on bridge interfaces.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

bridgeMaxSizeForwardingTable 1.3.6.1.4.1.173.7.9.4
Number of entries allowed in the bridge forwarding table
OBJECT-TYPE    
  INTEGER 128..65535  

bridgeIPEnabled 1.3.6.1.4.1.173.7.9.5
When yes, and BRIDGING ENABLED, IP traffic will be bridged, otherwise IP traffic will be routed.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

bridgeIPXEnabled 1.3.6.1.4.1.173.7.9.6
When yes, and BRIDGING ENABLED, IPX traffic will be bridged, otherwise IPX traffic will be routed.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

bridgeAdminSRBID 1.3.6.1.4.1.173.7.9.7
bridge ID to be inserted into token ring RIF field, this bridge
OBJECT-TYPE    
  INTEGER 0..15  

bridgeOperSRBID 1.3.6.1.4.1.173.7.9.8
bridge ID to be inserted into token ring RIF field, this bridge
OBJECT-TYPE    
  INTEGER 0..15  

bridgeDefaultEthernetFrameType 1.3.6.1.4.1.173.7.9.9
default frame type to be used when forwarding traffic on ethernet interfaces.
OBJECT-TYPE    
  INTEGER type-II(1), ieee8023(2)  

ipNl 1.3.6.1.4.1.173.7.11
OBJECT IDENTIFIER    

nlIpDefaultRIPVersion 1.3.6.1.4.1.173.7.11.1
The version of RIP that will be used by IP.
OBJECT-TYPE    
  INTEGER ripVersion1(1), rip1Compatible(2), ripVersion2(3)  

voice 1.3.6.1.4.1.173.7.12
OBJECT IDENTIFIER    

voiceSystemVoiceNodeNum 1.3.6.1.4.1.173.7.12.1
The number that identifies this node.
OBJECT-TYPE    
  INTEGER 1..9999  

voiceSystemRingVolFreq 1.3.6.1.4.1.173.7.12.2
The frequency and voltage of the telephone ring circuit. In two wire OPX mode, the node provides ring voltage to the telephone when it is called by a remote unit.
OBJECT-TYPE    
  INTEGER v75-hz-16-66(1), v80-hz-20-00(2), v75-hz-25-00(3), v60-hz-50-00(4), v75-hz-50-00(5)  

voiceSystemCountryCode 1.3.6.1.4.1.173.7.12.3
The telephone dialing prefix code that identifies the country in which the node is installed.
OBJECT-TYPE    
  INTEGER 1..999  

voiceSystemDialDigits 1.3.6.1.4.1.173.7.12.4
The number of digits that will be used in the speed dialing scheme, as well as the number of digits one can specify for the Auto Dial feature. This requires rebooting for the change to take effect.
OBJECT-TYPE    
  INTEGER 2..4  

voiceSystemVoiceRatesMin 1.3.6.1.4.1.173.7.12.5
The minimum operating rate of all voice channels when congestion occurs.
OBJECT-TYPE    
  INTEGER bps-4800(1), bps-8000(2), bps-32000(3), bps-64000(4)  

voiceSystemVoiceRatesMax 1.3.6.1.4.1.173.7.12.6
The maximum operating digitization rate of all voice channels when there is no congestion.
OBJECT-TYPE    
  INTEGER bps-4800(1), bps-8000(2), bps-32000(3), bps-64000(4)  

voiceSystemExtDialDigits 1.3.6.1.4.1.173.7.12.7
The number of extended dial digits that can be defined in the speed map table and/or entered by the user of attached equipment as part of a dial string. This requires rebooting for the change to take effect.
OBJECT-TYPE    
  INTEGER 0..16  

voiceSpeedDialTable 1.3.6.1.4.1.173.7.12.8
A list of speed-dial numbers.
OBJECT-TYPE    
  SEQUENCE OF  
    VoiceSpeedDialEntry

voiceSpeedDialEntry 1.3.6.1.4.1.173.7.12.8.1
A Voice Speed Dial entry containing objects relating to the speed-dial number that are configurable by the user.
OBJECT-TYPE    
  VoiceSpeedDialEntry  

voiceSpeedDialDigits 1.3.6.1.4.1.173.7.12.8.1.1
The speed-dial number. A question mark wildcard can be used for any digit, and an asterisk wildcard can be used for any number of digits.
OBJECT-TYPE    
  OCTET STRING SIZE(1..4)  

voiceSpeedDialLongDialMap 1.3.6.1.4.1.173.7.12.8.1.2
The number for which the speed-dial number is a shortcut.
OBJECT-TYPE    
  OCTET STRING SIZE(6)  

voiceSpeedDialExtDialStr 1.3.6.1.4.1.173.7.12.8.1.3
The extended set of digits that will be forwarded with the call if portVoiceOperExtDigitsSource in the physical port record is set to Map.
OBJECT-TYPE    
  OCTET STRING SIZE(1..16)  

voiceSpeedDialRowStatus 1.3.6.1.4.1.173.7.12.8.1.4
This variable is used to manage the creation and deletion of conceptual rows in the voiceSpeedDialTable and follows the SNMPv2 RowStatus conventions by supporting the following values: - `active', which indicates that the conceptual row is available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row does not exist. - `createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device. For a management protocol set operation, a genErr response is returned when the row already exists. - `destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Note that all of the above values may be specified in a management protocol set operation, and only the 'active' value will be returned in response to a management protocol retrieval operation. For a management protocol set operation, if other variable bindings are included in the same PDU, then a genErr response is returned.
OBJECT-TYPE    
  RowStatus  

Defined Objects

DisplayString  
OCTET STRING    

PhysAddress  
OCTET STRING    

NlSubscriberAddress  
OCTET STRING SIZE(1..15)    

NsEntry  
SEQUENCE    
  INTEGER as nsNodNum  
  INTEGER as nsStatus  
  INTEGER as nsNumNeigh  

NsNeighEntry  
SEQUENCE    
  INTEGER as nsNTNode  
  INTEGER as nsNTNeigh  
  INTEGER as nsNTNeighStat  

TpAdrEntry  
SEQUENCE    
  INTEGER as tpAdrIdx  
  IpAddress as tpAddress  
  INTEGER as tpAdrFlag  
  INTEGER as tpAdrSLev  

RlpEntry  
SEQUENCE    
  INTEGER as rlpIndex  
  INTEGER as rlpStatus  
  INTEGER as rlpMemorySize  
  INTEGER as rlpLIC1Type  
  INTEGER as rlpLIC2Type  
  OCTET STRING as rlpProtocol  
  INTEGER as rlpGroupNumber  
  INTEGER as rlpGroupResponsibility  

PortPhyX25AdminEntry  
SEQUENCE    
  INTEGER as portPhyX25AdminConnector  
  INTEGER as portPhyX25AdminSpeed  
  INTEGER as portPhyX25AdminGenerateClock  
  INTEGER as portPhyX25AdminRcvClockFromDTE  
  INTEGER as portPhyX25AdminDialOut  
  INTEGER as portPhyX25AdminInactivityTimer  
  INTEGER as portPhyX25AdminDisconnectTimer  
  INTEGER as portPhyX25AdminSetupTimer  
  INTEGER as portPhyX25AdminTrunkFlag  
  OCTET STRING as portPhyX25AdminTrunkGroup  
  RowStatus as portPhyX25AdminRowStatus  

PortPhyX25OperEntry  
SEQUENCE    
  INTEGER as portPhyX25OperConnector  
  INTEGER as portPhyX25OperSpeed  
  INTEGER as portPhyX25OperGenerateClock  
  INTEGER as portPhyX25OperRcvClockFromDTE  
  INTEGER as portPhyX25OperDialOut  
  INTEGER as portPhyX25OperInactivityTimer  
  INTEGER as portPhyX25OperDisconnectTimer  
  INTEGER as portPhyX25OperSetupTimer  
  INTEGER as portPhyX25OperTrunkFlag  
  OCTET STRING as portPhyX25OperTrunkGroup  

PortLogicalX25AdminEntry  
SEQUENCE    
  INTEGER as portLogicalX25AdminFrDlci  
  INTEGER as portLogicalX25AdminCxnPriority  
  INTEGER as portLogicalX25AdminRfc1490  
  INTEGER as portLogicalX25AdminBAG  
  RowStatus as portLogicalX25AdminRowStatus  

PortLogicalX25OperEntry  
SEQUENCE    
  INTEGER as portLogicalX25OperFrDlci  
  INTEGER as portLogicalX25OperCxnPriority  
  INTEGER as portLogicalX25OperRfc1490  
  INTEGER as portLogicalX25OperBAG  

PortX25AdminEntry  
SEQUENCE    
  INTEGER as portX25AdminBlockedFlag  
  INTEGER as portX25AdminFlowCtrlNeg  
  INTEGER as portX25AdminThruptClassNeg  
  INTEGER as portX25AdminLocChgPrev  
  INTEGER as portX25AdminRevChgAccpt  
  INTEGER as portX25AdminFastSelAccpt  
  INTEGER as portX25AdminInCallBar  
  INTEGER as portX25AdminOutCallBar  
  INTEGER as portX25AdminMaxPktSize  
  INTEGER as portX25AdminDefPktSize  
  INTEGER as portX25AdminMaxWinSize  
  INTEGER as portX25AdminDefWinSize  
  INTEGER as portX25AdminMaxThruptClass  
  INTEGER as portX25AdminCUGPref  
  INTEGER as portX25AdminCUGIndex  
  INTEGER as portX25AdminCUGIncAccess  
  INTEGER as portX25AdminCUGOutAccess  

PortX25OperEntry  
SEQUENCE    
  INTEGER as portX25OperBlockedFlag  
  INTEGER as portX25OperFlowCtrlNeg  
  INTEGER as portX25OperThruptClassNeg  
  INTEGER as portX25OperLocChgPrev  
  INTEGER as portX25OperRevChgAccpt  
  INTEGER as portX25OperFastSelAccpt  
  INTEGER as portX25OperInCallBar  
  INTEGER as portX25OperOutCallBar  
  INTEGER as portX25OperMaxPktSize  
  INTEGER as portX25OperDefPktSize  
  INTEGER as portX25OperMaxWinSize  
  INTEGER as portX25OperDefWinSize  
  INTEGER as portX25OperMaxThruptClass  
  INTEGER as portX25OperCUGPref  
  INTEGER as portX25OperCUGIndex  
  INTEGER as portX25OperCUGIncAccess  
  INTEGER as portX25OperCUGOutAccess  

PortFrEntry  
SEQUENCE    
  INTEGER as portFrRlpIndex  
  INTEGER as portFrPortIndex  
  INTEGER as portFrBlockedFlag  
  INTEGER as portFrMaxBytesPerFrame  
  INTEGER as portFrT392Timer  
  INTEGER as portFrOutgoingRateControl  
  INTEGER as portFrBandwidthAllocation  
  INTEGER as portFrConnector  
  INTEGER as portFrLogicalDCE  
  INTEGER as portFrGenClock  
  INTEGER as portFrRcvClkFrmDTE  
  INTEGER as portFrLLM  
  RowStatus as portFrRowStatus  
  INTEGER as portFrSpeed  
  INTEGER as portFrBackupUseOnly  

PortDLCIEntry  
SEQUENCE    
  INTEGER as portDLCIRlpIndex  
  INTEGER as portDLCIPortIndex  
  INTEGER as portDLCIIndex  
  INTEGER as portDLCIIncomingCIR  
  INTEGER as portDLCIOutgoingCIR  
  INTEGER as portDLCIIncomingBc  
  INTEGER as portDLCIOutgoingBc  
  INTEGER as portDLCIIncomingBe  
  INTEGER as portDLCIOutgoingBe  
  INTEGER as portDLCIBecnRecoveryCnt  
  INTEGER as portDLCIPriority  
  RowStatus as portDLCIRowStatus  
  INTEGER as portDLCIBackupGroup  
  INTEGER as portDLCIBackupProtEnb  

FrBackupEntry  
SEQUENCE    
  INTEGER as portFrBackupRLP  
  INTEGER as portFrBackupPort  
  INTEGER as portFrBackupDLCI  
  INTEGER as portFrBackupGroup  
  INTEGER as portFrBackupWaitTimer  
  INTEGER as portFrBackupProtEnab  
  RowStatus as portFrBackupRowStatus  

PortBsciAdminEntry  
SEQUENCE    
  INTEGER as portBsciAdminBlockedFlag  
  INTEGER as portBsciAdminConnector  
  INTEGER as portBsciAdminSpeed  
  INTEGER as portBsciAdminRetransmitInterval  
  INTEGER as portBsciAdminMAXRetransmits  
  INTEGER as portBsciAdminMaxBytesPerFrame  
  INTEGER as portBsciAdminGenerateClock  
  INTEGER as portBsciAdminRcvClockFromDTE  
  INTEGER as portBsciAdminPadType  
  INTEGER as portBsciAdminUseEBCDIC  
  INTEGER as portBsciAdminCallInfoInRequestPacket  
  INTEGER as portBsciAdminClearVCOnLastDeviceDown  
  INTEGER as portBsciAdminTransTextSupported  
  INTEGER as portBsciAdminEndToEndAck  
  INTEGER as portBsciAdminFullDuplex  
  INTEGER as portBsciAdminMultidrop  
  INTEGER as portBsciAdminSlowPollRetryCount  
  INTEGER as portBsciAdminSlowPollRetryFreq  
  INTEGER as portBsciAdminStartSynchChars  
  INTEGER as portBsciAdminEndPadChars  
  INTEGER as portBsciAdminPollInterval  
  INTEGER as portBsciAdminNoResponseTimer  
  INTEGER as portBsciAdminNoResponseRetryCount  
  INTEGER as portBsciAdminErrorRetransmitCount  
  INTEGER as portBsciAdminNAKRetryCount  
  INTEGER as portBsciAdminBlockCheck  
  INTEGER as portBsciAdminDataMode  
  RowStatus as portBsciAdminRowStatus  
  INTEGER as portBsciAdminAnswerNonConfigured  
  INTEGER as portBsciAdminActivateConnectionWithoutPoll  

PortBsciOperEntry  
SEQUENCE    
  INTEGER as portBsciOperBlockedFlag  
  INTEGER as portBsciOperConnector  
  INTEGER as portBsciOperSpeed  
  INTEGER as portBsciOperRetransmitInterval  
  INTEGER as portBsciOperMAXRetransmits  
  INTEGER as portBsciOperMaxBytesPerFrame  
  INTEGER as portBsciOperGenerateClock  
  INTEGER as portBsciOperRcvClockFromDTE  
  INTEGER as portBsciOperPadType  
  INTEGER as portBsciOperUseEBCDIC  
  INTEGER as portBsciOperCallInfoInRequestPacket  
  INTEGER as portBsciOperClearVCOnLastDeviceDown  
  INTEGER as portBsciOperTransTextSupported  
  INTEGER as portBsciOperEndToEndAck  
  INTEGER as portBsciOperFullDuplex  
  INTEGER as portBsciOperMultidrop  
  INTEGER as portBsciOperSlowPollRetryCount  
  INTEGER as portBsciOperSlowPollRetryFreq  
  INTEGER as portBsciOperStartSynchChars  
  INTEGER as portBsciOperEndPadChars  
  INTEGER as portBsciOperPollInterval  
  INTEGER as portBsciOperNoResponseTimer  
  INTEGER as portBsciOperNoResponseRetryCount  
  INTEGER as portBsciOperErrorRetransmitCount  
  INTEGER as portBsciOperNAKRetryCount  
  INTEGER as portBsciOperBlockCheck  
  INTEGER as portBsciOperDataMode  
  INTEGER as portBsciOperAnswerNonConfigured  
  INTEGER as portBsciOperActivateConnectionWithoutPoll  

BsciSubscrAdminEntry  
SEQUENCE    
  INTEGER as bsciSubscrAdminSequence  
  NlSubscriberAddress as bsciSubscrAdminLocalID  
  NlSubscriberAddress as bsciSubscrAdminRemoteID  
  INTEGER as bsciSubscrAdminAutocall  
  INTEGER as bsciSubscrAdminAutocallRtyTimer  
  INTEGER as bsciSubscrAdminAutocallMaxRtry  
  INTEGER as bsciSubscrAdminConnectionID  
  RowStatus as bsciSubscrAdminRowStatus  

BsciSubscrOperEntry  
SEQUENCE    
  INTEGER as bsciSubscrOperSequence  
  NlSubscriberAddress as bsciSubscrOperLocalID  
  NlSubscriberAddress as bsciSubscrOperRemoteID  
  INTEGER as bsciSubscrOperAutocall  
  INTEGER as bsciSubscrOperAutocallRtyTimer  
  INTEGER as bsciSubscrOperAutocallMaxRtry  
  INTEGER as bsciSubscrOperConnectionID  

BsciDevAdminEntry  
SEQUENCE    
  INTEGER as bsciDevAdminControlUnitID  
  INTEGER as bsciDevAdminDeviceUnitID  
  INTEGER as bsciDevAdminConnectionID  
  INTEGER as bsciDevAdminSingleUserVC  
  INTEGER as bsciDevAdminTransTextSupported  
  INTEGER as bsciDevAdminPrinterAttached  
  RowStatus as bsciDevAdminRowStatus  
  INTEGER as bsciDevAdminDisableStatusRequest  

BsciDevOperEntry  
SEQUENCE    
  INTEGER as bsciDevOperControlUnitID  
  INTEGER as bsciDevOperDeviceUnitID  
  INTEGER as bsciDevOperConnectionID  
  INTEGER as bsciDevOperSingleUserVC  
  INTEGER as bsciDevOperTransTextSupported  
  INTEGER as bsciDevOperPrinterAttached  
  INTEGER as bsciDevOperDisableStatusRequest  

PortSdlcAdminEntry  
SEQUENCE    
  INTEGER as portSdlcAdminCommit  
  INTEGER as portSdlcAdminMAXRetries  
  INTEGER as portSdlcAdminMAXOut  
  INTEGER as portSdlcAdminPadType  
  INTEGER as portSdlcAdminGenerateClock  
  INTEGER as portSdlcAdminRcvClockFromDTE  
  INTEGER as portSdlcAdminNrz  
  INTEGER as portSdlcAdminPacketSize  
  INTEGER as portSdlcAdminDisableRequestDisconnect  
  INTEGER as portSdlcAdminLPDASupport  
  INTEGER as portSdlcAdminConnector  
  INTEGER as portSdlcAdminSpeed  
  RowStatus as portSdlcAdminRowStatus  
  INTEGER as portSdlcAdminIdleFillChar  
  INTEGER as portSdlcAdminInactivityTimer  
  INTEGER as portSdlcAdminL1Duplex  

PortSdlcOperEntry  
SEQUENCE    
  INTEGER as portSdlcOperCommit  
  INTEGER as portSdlcOperMAXRetries  
  INTEGER as portSdlcOperMAXOut  
  INTEGER as portSdlcOperPadType  
  INTEGER as portSdlcOperGenerateClock  
  INTEGER as portSdlcOperRcvClockFromDTE  
  INTEGER as portSdlcOperNrz  
  INTEGER as portSdlcOperPacketSize  
  INTEGER as portSdlcOperDisableRequestDisconnect  
  INTEGER as portSdlcOperLPDASupport  
  INTEGER as portSdlcOperConnector  
  INTEGER as portSdlcOperSpeed  
  INTEGER as portSdlcOperIdleFillChar  
  INTEGER as portSdlcOperInactivityTimer  
  INTEGER as portSdlcOperL1Duplex  

LSSdlcAdminEntry  
SEQUENCE    
  NlSubscriberAddress as lSSdlcAdminLocalSub  
  NlSubscriberAddress as lSSdlcAdminRemoteSub  
  INTEGER as lSSdlcAdminAutoCall  
  INTEGER as lSSdlcAdminRetryTime  
  INTEGER as lSSdlcAdminRetryCount  
  INTEGER as lSSdlcAdminLlc2Conversion  
  INTEGER as lSSdlcAdminLPDAResourceID  
  RowStatus as lSSdlcAdminRowStatus  
  INTEGER as lSSdlcAdminL2DatMode  

LSSdlcOperEntry  
SEQUENCE    
  NlSubscriberAddress as lSSdlcOperLocalSub  
  NlSubscriberAddress as lSSdlcOperRemoteSub  
  INTEGER as lSSdlcOperAutoCall  
  INTEGER as lSSdlcOperRetryTime  
  INTEGER as lSSdlcOperRetryCount  
  INTEGER as lSSdlcOperLlc2Conversion  
  INTEGER as lSSdlcOperLPDAResourceID  
  INTEGER as lSSdlcOperL2DatMode  

LSSdlcLlc2AdminEntry  
SEQUENCE    
  INTEGER as lSSdlcLlc2AdminLocalSap  
  PhysAddress as lSSdlcLlc2AdminLocalMac  
  INTEGER as lSSdlcLlc2AdminIdblk  
  INTEGER as lSSdlcLlc2AdminIdnum  
  INTEGER as lSSdlcLlc2AdminLanTi  
  INTEGER as lSSdlcLlc2AdminLanT1  
  INTEGER as lSSdlcLlc2AdminLanT2  
  INTEGER as lSSdlcLlc2AdminLanN2  
  INTEGER as lSSdlcLlc2AdminLanN3  
  INTEGER as lSSdlcLlc2AdminLanTw  
  INTEGER as lSSdlcLlc2AdminBAG  
  INTEGER as lSSdlcLlc2AdminPriority  
  RowStatus as lSSdlcLlc2AdminRowStatus  
  INTEGER as lSSdlcLlc2AdminSuppressXID  

LSSdlcLlc2OperEntry  
SEQUENCE    
  INTEGER as lSSdlcLlc2OperLocalSap  
  PhysAddress as lSSdlcLlc2OperLocalMac  
  INTEGER as lSSdlcLlc2OperIdblk  
  INTEGER as lSSdlcLlc2OperIdnum  
  INTEGER as lSSdlcLlc2OperLanTi  
  INTEGER as lSSdlcLlc2OperLanT1  
  INTEGER as lSSdlcLlc2OperLanT2  
  INTEGER as lSSdlcLlc2OperLanN2  
  INTEGER as lSSdlcLlc2OperLanN3  
  INTEGER as lSSdlcLlc2OperLanTw  
  INTEGER as lSSdlcLlc2OperBAG  
  INTEGER as lSSdlcLlc2OperPriority  
  INTEGER as lSSdlcLlc2OperSuppressXID  

PortT1AdminEntry  
SEQUENCE    
  INTEGER as portT1AdminBlockedPortFlag  
  INTEGER as portT1AdminGenerateClock  
  INTEGER as portT1AdminFramingMode  
  INTEGER as portT1AdminFrameModelSelect  
  INTEGER as portT1AdminLineEncoding  
  INTEGER as portT1AdminLineBuildOut  
  RowStatus as portT1AdminRowStatus  
  INTEGER as portT1AdminProtocolFraming  
  INTEGER as portT1AdminNRZI  

PortT1OperEntry  
SEQUENCE    
  INTEGER as portT1OperBlockedPortFlag  
  INTEGER as portT1OperGenerateClock  
  INTEGER as portT1OperFramingMode  
  INTEGER as portT1OperFrameModelSelect  
  INTEGER as portT1OperLineEncoding  
  INTEGER as portT1OperLineBuildOut  
  INTEGER as portT1OperProtocolFraming  
  INTEGER as portT1OperNRZI  

PortVoiceAdminEntry  
SEQUENCE    
  INTEGER as portVoiceAdminRlpIndex  
  INTEGER as portVoiceAdminPortIndex  
  INTEGER as portVoiceAdminBlockedFlag  
  INTEGER as portVoiceAdminSpeed  
  INTEGER as portVoiceAdminDTMF  
  INTEGER as portVoiceAdminInterface  
  INTEGER as portVoiceAdminTETimer  
  INTEGER as portVoiceAdminLevelIn  
  INTEGER as portVoiceAdminLevelOut  
  INTEGER as portVoiceAdminCallTimer  
  INTEGER as portVoiceAdminHuntGroup  
  OCTET STRING as portVoiceAdminLongDialPrefix  
  INTEGER as portVoiceAdminSLTTimeout  
  INTEGER as portVoiceAdminLinkDownBusy  
  INTEGER as portVoiceAdminFaxSupported  
  INTEGER as portVoiceAdminTelephonyType  
  INTEGER as portVoiceAdminJitter  
  INTEGER as portVoiceAdminSampleDelay  
  INTEGER as portVoiceAdminDialTimer  
  INTEGER as portVoiceAdminAutoDial  
  INTEGER as portVoiceAdminSuppression  
  OCTET STRING as portVoiceAdminAutoDialNumber  
  INTEGER as portVoiceAdminAutoPoll  
  INTEGER as portVoiceAdminAutoPollTimer  
  INTEGER as portVoiceAdminExtDigitsSource  
  INTEGER as portVoiceAdminNumDigitsDelete  
  INTEGER as portVoiceAdminForwardDelay  
  INTEGER as portVoiceAdminForwardedType  
  INTEGER as portVoiceAdminForwardedDigits  
  INTEGER as portVoiceAdminMakeRatio  
  INTEGER as portVoiceAdminBreakRatio  
  INTEGER as portVoiceAdminDTMFOnDuration  
  INTEGER as portVoiceAdminDTMFOffDuration  
  INTEGER as portVoiceAdminToneType  
  RowStatus as portVoiceAdminRowStatus  

PortVoiceOperEntry  
SEQUENCE    
  INTEGER as portVoiceOperRlpIndex  
  INTEGER as portVoiceOperPortIndex  
  INTEGER as portVoiceOperBlockedFlag  
  INTEGER as portVoiceOperSpeed  
  INTEGER as portVoiceOperDTMF  
  INTEGER as portVoiceOperInterface  
  INTEGER as portVoiceOperTETimer  
  INTEGER as portVoiceOperLevelIn  
  INTEGER as portVoiceOperLevelOut  
  INTEGER as portVoiceOperCallTimer  
  INTEGER as portVoiceOperHuntGroup  
  OCTET STRING as portVoiceOperLongDialPrefix  
  INTEGER as portVoiceOperSLTTimeout  
  INTEGER as portVoiceOperLinkDownBusy  
  INTEGER as portVoiceOperFaxSupported  
  INTEGER as portVoiceOperTelephonyType  
  INTEGER as portVoiceOperJitter  
  INTEGER as portVoiceOperSampleDelay  
  INTEGER as portVoiceOperDialTimer  
  INTEGER as portVoiceOperAutoDial  
  INTEGER as portVoiceOperSuppression  
  OCTET STRING as portVoiceOperAutoDialNumber  
  INTEGER as portVoiceOperAutoPoll  
  INTEGER as portVoiceOperAutoPollTimer  
  INTEGER as portVoiceOperExtDigitsSource  
  INTEGER as portVoiceOperNumDigitsDelete  
  INTEGER as portVoiceOperForwardDelay  
  INTEGER as portVoiceOperForwardedType  
  INTEGER as portVoiceOperForwardedDigits  
  INTEGER as portVoiceOperMakeRatio  
  INTEGER as portVoiceOperBreakRatio  
  INTEGER as portVoiceOperDTMFOnDuration  
  INTEGER as portVoiceOperDTMFOffDuration  
  INTEGER as portVoiceOperToneType  

NlIfEntry  
SEQUENCE    
  INTEGER as nlIfRlp  
  INTEGER as nlIfPort  
  INTEGER as nlIfType  
  INTEGER as nlIfIndex  
  INTEGER as nlIfTableIndex  
  OBJECT IDENTIFIER as nlIfTableOid  
  INTEGER as nlIfConnectorType  
  INTEGER as nlIfPortStatus  
  INTEGER as nlIfPhyPort  

NlIfLlc2LANEntry  
SEQUENCE    
  INTEGER as nlIfLlc2LANRlp  
  INTEGER as nlIfLlc2LANPort  
  INTEGER as nlIfLlc2LANType  
  INTEGER as nlIfLlc2LANCard  
  INTEGER as nlIfLlc2LANID  
  INTEGER as nlIfLlc2LANInterface  
  RowStatus as nlIfLlc2LANRowStatus  
  INTEGER as nlIfLlc2LANPriority  
  INTEGER as nlIfLlc2LANBlockedPortFlag  

NlIfLlc2FrEntry  
SEQUENCE    
  INTEGER as nlIfLlc2FrRlp  
  INTEGER as nlIfLlc2FrPort  
  INTEGER as nlIfLlc2FrDLCI  
  INTEGER as nlIfLlc2FrFormat  
  INTEGER as nlIfLlc2FrPriority  
  INTEGER as nlIfLlc2FrBAG  
  MacAddress as nlIfLlc2FrHostMACAddress  
  INTEGER as nlIfLlc2FrSessionType  
  INTEGER as nlIfLlc2FrLANID  
  INTEGER as nlIfLlc2FrInterface  
  RowStatus as nlIfLlc2FrRowStatus  
  INTEGER as nlIfLlc2FrBlockedPortFlag  

IPXStaticRouteConfigEntry  
SEQUENCE    
  INTEGER as ipxStaticRouteConfigCircIndex  
  OCTET STRING as ipxStaticRouteConfigNetNum  
  OCTET STRING as ipxStaticRouteConfigRouter  
  RowStatus as ipxStaticRouteConfigRowStatus  

IPXServConfigEntry  
SEQUENCE    
  INTEGER as ipxServConfigServiceType  
  OCTET STRING as ipxServConfigServName  
  INTEGER as ipxServConfigServNetworkAddress  
  OCTET STRING as ipxServConfigServNodeAddress  
  INTEGER as ipxServConfigServSocketNumber  
  INTEGER as ipxServConfigInterveningNetworks  
  OCTET STRING as ipxServConfigGatewayAddress  
  INTEGER as ipxServConfigInterface  
  RowStatus as ipxServConfigRowStatus  

IPXInterfaceEntry  
SEQUENCE    
  INTEGER as ipxInterfaceNumber  
  INTEGER as ipxInterfaceBlockedPortFlag  
  INTEGER as ipxInterfaceType  
  INTEGER as ipxInterfaceFrameType  
  INTEGER as ipxInterfaceMaxTransUnit  
  INTEGER as ipxInterfaceNetworkAddress  
  INTEGER as ipxInterfaceBandwidthAllocGroup  
  INTEGER as ipxInterfacePortDiagEnabled  
  INTEGER as ipxInterfaceNetBIOSEnabled  
  INTEGER as ipxInterfaceNetBIOSHops  
  INTEGER as ipxInterfacePeriodicRIPEnabled  
  INTEGER as ipxInterfacePeriodicRIPTimer  
  INTEGER as ipxInterfacePeriodicSAPEnabled  
  INTEGER as ipxInterfacePeriodicSAPTimer  
  INTEGER as ipxInterfaceRIPEnabled  
  INTEGER as ipxInterfaceRIPAgeTimer  
  INTEGER as ipxInterfaceRIPMaxSize  
  INTEGER as ipxInterfaceSAPEnabled  
  INTEGER as ipxInterfaceSAPAgeTimer  
  INTEGER as ipxInterfaceTransportTime  
  INTEGER as ipxInterfaceSerializationEnabled  
  INTEGER as ipxInterfaceWatchdogSpoofingEnabled  
  INTEGER as ipxInterfaceLanCardNumber  
  INTEGER as ipxInterfaceWanEnabled  
  OCTET STRING as ipxInterfaceSourceSubscriber  
  OCTET STRING as ipxInterfaceDestinationSubscriber  
  INTEGER as ipxInterfaceSVCRetryTimer  
  INTEGER as ipxInterfaceSVCIdleTimer  
  INTEGER as ipxInterfaceMaxVC  
  INTEGER as ipxInterfacePVCConnection  
  INTEGER as ipxInterfaceSourceCard  
  INTEGER as ipxInterfaceSourcePort  
  INTEGER as ipxInterfaceSourceDLCI  
  RowStatus as ipxInterfaceRowStatus  

NlIfIpEntry  
SEQUENCE    
  INTEGER as nlIfIpInterface  
  INTEGER as nlIfIpMtu  
  IpAddress as nlIfIpNetworkMask  
  INTEGER as nlIfIpRouteMetric  
  INTEGER as nlIfIpICMPAddRoutes  
  INTEGER as nlIfIpRIPDeltaUpdates  
  INTEGER as nlIfIpRIPFullUpdates  
  INTEGER as nlIfIpPriority  
  INTEGER as nlIfIpBAG  
  INTEGER as nlIfIpType  
  IpAddress as nlIfIpSourceAddress  
  IpAddress as nlIfIpDestAddress  
  IpAddress as nlIfIpBroadcastAddress  
  INTEGER as nlIfIpLANCard  
  NlSubscriberAddress as nlIfIpSourceSub  
  NlSubscriberAddress as nlIfIpDestSub  
  INTEGER as nlIfIpSVCRetryTimer  
  INTEGER as nlIfIpSVCIdleTimer  
  INTEGER as nlIfIpMaxSVC  
  INTEGER as nlIfIpPVCConnection  
  INTEGER as nlIfIpSourceRlp  
  INTEGER as nlIfIpSourcePort  
  INTEGER as nlIfIpSourceDLCI  
  INTEGER as nlIfIpRIPSupport  
  INTEGER as nlIfIpInverseARP  
  INTEGER as nlIfIpProxyARP  
  INTEGER as nlIfIpUnnumberedIf  
  RowStatus as nlIfIpRowStatus  

NlIfIpSecondaryAddrEntry  
SEQUENCE    
  INTEGER as nlIfIpSecondaryAddrSequence  
  IpAddress as nlIfIpSecondaryAddrNetworkMask  
  INTEGER as nlIfIpSecondaryAddrRouteMetric  
  IpAddress as nlIfIpSecondaryAddrSourceAddress  
  IpAddress as nlIfIpSecondaryAddrBroadcastAddress  
  INTEGER as nlIfIpSecondaryAddrRIPSupport  
  RowStatus as nlIfIpSecondaryAddrRowStatus  

NlIfVoiceEntry  
SEQUENCE    
  INTEGER as nlIfVoiceInterface  
  INTEGER as nlIfVoicePeerNodeType  
  INTEGER as nlIfVoicePeerNodeNumber  
  INTEGER as nlIfVoicePeerNodePort  
  INTEGER as nlIfVoiceLocalNodeNumber  
  INTEGER as nlIfVoiceLocalNodePort  
  INTEGER as nlIfVoiceFrameRelayRlp  
  INTEGER as nlIfVoiceFrameRelayPort  
  INTEGER as nlIfVoiceFrameRelayDLCI  
  INTEGER as nlIfVoiceEnableFragment  
  RowStatus as nlIfVoiceRowStatus  

NlLocalSubscriberEntry  
SEQUENCE    
  NlSubscriberAddress as nlLocalSubscriberId  
  DisplayString as nlLocalSubscriberName  
  INTEGER as nlLocalSubscriberAlgorithm  
  INTEGER as nlLocalSubscriberSystematicRedirect  
  INTEGER as nlLocalSubscriberRedirectBusy  
  INTEGER as nlLocalSubscriberRedirectOO  
  INTEGER as nlLocalSubscriberPriority  
  RowStatus as nlLocalSubscriberRowStatus  

NlLocalSubscriberRouteEntry  
SEQUENCE    
  INTEGER as nlLocalSubscriberRouteIndex  
  INTEGER as nlLocalSubscriberRouteConf  
  INTEGER as nlLocalSubscriberRouteLP  
  INTEGER as nlLocalSubscriberRoutePort  
  RowStatus as nlLocalSubscriberRouteRowStatus  

NlLocalSubscriberRedirEntry  
SEQUENCE    
  INTEGER as nlLocalSubscriberRedirIndex  
  NlSubscriberAddress as nlLocalSubscriberRedirAddr  
  RowStatus as nlLocalSubscriberRedirRowStatus  

NlLlc2HostEntry  
SEQUENCE    
  INTEGER as nlLlc2HostIndex  
  MacAddress as nlLlc2HostMACAddress  
  INTEGER as nlLlc2HostSessionType  
  TimeInterval as nlLlc2HostT1ReplyTimer  
  TimeInterval as nlLlc2HostT2RecvAckTimer  
  TimeInterval as nlLlc2HostTiInactivityTimer  
  INTEGER as nlLlc2HostN3NumberLPDUs  
  INTEGER as nlLlc2HostTwNumberOutstanding  
  INTEGER as nlLlc2HostN2ExpiredT1LPDUCount  
  INTEGER as nlLlc2HostPriority  
  INTEGER as nlLlc2HostBAG  
  NlSubscriberAddress as nlLlc2HostRoutingSubscriberId  
  MacAddress as nlLlc2HostSrcMACAddressMask  
  INTEGER as nlLlc2HostAccess  
  RowStatus as nlLlc2HostRowStatus  
  INTEGER as nlLlc2HostInterface  
  INTEGER as nlLlc2HostGroup  

NlLlc2TermConnectionEntry  
SEQUENCE    
  INTEGER as nlLlc2TermConnectionSequence  
  INTEGER as nlLlc2TermConnectionHSAP  
  NlSubscriberAddress as nlLlc2TermConnectionLocalSubscriberId  
  NlSubscriberAddress as nlLlc2TermConnectionRemoteSubscriberId  
  RowStatus as nlLlc2TermConnectionRowStatus  

NlLlc2OrigConnectionEntry  
SEQUENCE    
  INTEGER as nlLlc2OrigConnectionSequence  
  INTEGER as nlLlc2OrigConnectionHSAP  
  INTEGER as nlLlc2OrigConnectionType  
  NlSubscriberAddress as nlLlc2OrigConnectionLocalSubscriberId  
  NlSubscriberAddress as nlLlc2OrigConnectionRemoteSubscriberId  
  INTEGER as nlLlc2OrigConnectionIDBLK  
  INTEGER as nlLlc2OrigConnectionIDNUM  
  INTEGER as nlLlc2OrigConnectionMAXDATA  
  INTEGER as nlLlc2OrigConnectionMAXIN  
  RowStatus as nlLlc2OrigConnectionRowStatus  

PortPinEntry  
SEQUENCE    
  INTEGER as portPinRlp  
  INTEGER as portPinPort  
  OCTET STRING as portPinStatus  

RlpStatsEntry  
SEQUENCE    
  INTEGER as rlpStatsIndex  
  Counter as rlpStatsUsedBuffers  
  Counter as rlpStatsQMessages  
  Counter as rlpStatsInFrames  
  Counter as rlpStatsOutFrames  
  Counter as rlpStatsFrameRejects  
  Counter as rlpStatsFrameRetransmits  

PortStatsEntry  
SEQUENCE    
  INTEGER as portStatsRlpIndex  
  INTEGER as portStatsIndex  
  Counter as portStatsInFrames  
  Counter as portStatsOutFrames  
  Counter as portStatsFrameRetrans  
  Counter as portStatsFCSErrors  
  Counter as portStatsLogicalRejects  
  Counter as portStatsInPercentUtils  
  Counter as portStatsOutPercentUtils  

FrStatsEntry  
SEQUENCE    
  INTEGER as frStatsRlpIndex  
  INTEGER as frStatsPortIndex  
  Counter as frStatsRxDEFrames  
  Counter as frStatsTxDEFrames  
  Counter as frStatsTxFECNFrames  
  Counter as frStatsRxFECNFrames  
  Counter as frStatsTxBECNFrames  
  Counter as frStatsRxBECNFrames  
  Counter as frStatsTxLMIFrames  
  Counter as frStatsRxLMIFrames  
  Counter as frStatsTxANXDFrames  
  Counter as frStatsRxANXDFrames  
  Counter as frStatsTotDiscFrames  

X25TxStatsEntry  
SEQUENCE    
  INTEGER as x25TxRlpIndex  
  INTEGER as x25TxPortIndex  
  Counter as x25TxSABMFrames  
  Counter as x25TxUAFrames  
  Counter as x25TxDISCFrames  
  Counter as x25TxDMFrames  
  Counter as x25TxFRMRFrames  
  Counter as x25TxREJFrames  
  Counter as x25TxRRFrames  
  Counter as x25TxRNRFrames  
  Counter as x25TxINFOFrames  

X25RxStatsEntry  
SEQUENCE    
  INTEGER as x25RxRlpIndex  
  INTEGER as x25RxPortIndex  
  Counter as x25RxSABMFrames  
  Counter as x25RxUAFrames  
  Counter as x25RxDISCFrames  
  Counter as x25RxDMFrames  
  Counter as x25RxFRMRFrames  
  Counter as x25RxREJFrames  
  Counter as x25RxRRFrames  
  Counter as x25RxRNRFrames  
  Counter as x25RxINFOFrames  

T1StatsEntry  
SEQUENCE    
  INTEGER as t1StatsRlpIndex  
  INTEGER as t1StatsPortIndex  
  Counter as t1StatsRcvFrames  
  Counter as t1StatsXmitFrames  
  Counter as t1StatsLCVCnt  
  Counter as t1StatsPCVRErrs  
  Counter as t1StatsOOSCnt  
  Counter as t1StatsBlueAlarms  
  Counter as t1StatsYellowAlarms  
  Counter as t1StatsRedAlarms  
  Counter as t1StatsRcvUsage  
  Counter as t1StatsXmitUsage  
  Counter as t1StatsXmitAbortFrames  
  Counter as t1StatsRcvAbortFrames  
  Counter as t1StatsRcvOverruns  
  Counter as t1StatsRcvErrors  
  Counter as t1StatsRcvChannelErrors  

DS0AStatsEntry  
SEQUENCE    
  INTEGER as ds0aStatsRlpIndex  
  INTEGER as ds0aStatsPortIndex  
  INTEGER as ds0aStatsChannelIndex  
  Counter as ds0aStatsXmitFrames  
  Counter as ds0aStatsRcvFrames  
  Counter as ds0aStatsRcvAbortFrames  
  Counter as ds0aStatsRcvOverruns  
  Counter as ds0aStatsRcvErrors  

VoiceStatsEntry  
SEQUENCE    
  INTEGER as voiceStatsRlpIndex  
  INTEGER as voiceStatsPortIndex  
  Counter as voiceStatsRxCalls  
  Counter as voiceStatsTxCalls  
  Counter as voiceStatsRxCallsAccepts  
  Counter as voiceStatsTxCallsAccepts  
  Counter as voiceStatsRxClears  
  Counter as voiceStatsTxClears  
  Counter as voiceStatsBusyCalls  
  Counter as voiceStatsCallTimeouts  
  Counter as voiceStatsRxCongestions  
  Counter as voiceStatsTxCongestions  

RlpThreshEntry  
SEQUENCE    
  INTEGER as rlpThreshRlpIndex  
  INTEGER as rlpThreshPercntBufInUse  
  INTEGER as rlpThreshMsgQueueLen  
  INTEGER as rlpThreshRxFramesPerSec  
  INTEGER as rlpThreshTxFramesPerSec  
  INTEGER as rlpThreshRejFramesPerSec  
  INTEGER as rlpThreshRtxFramesPerSec  

PortThreshEntry  
SEQUENCE    
  INTEGER as portThreshRlpIndex  
  INTEGER as portThreshIndex  
  INTEGER as portThreshRxFramesPerSec  
  INTEGER as portThreshTxFramesPerSec  
  INTEGER as portThreshRtxFramesPerSec  
  INTEGER as portThreshFCSErrPerSec  
  INTEGER as portThreshLogRejPerSec  
  INTEGER as portThreshTxErrorRatio  
  INTEGER as portThreshRxErrorRatio  
  INTEGER as portThreshTxPercentUtl  
  INTEGER as portThreshRxPercentUtl  

VoiceSpeedDialEntry  
SEQUENCE    
  OCTET STRING as voiceSpeedDialDigits  
  OCTET STRING as voiceSpeedDialLongDialMap  
  OCTET STRING as voiceSpeedDialExtDialStr  
  RowStatus as voiceSpeedDialRowStatus