NETSCREEN-OSPF-MIB

File: NETSCREEN-OSPF-MIB.mib (80101 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
RFC1213-MIB NETSCREEN-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Gauge32 Integer32 IpAddress
TEXTUAL-CONVENTION TruthValue RowStatus
MODULE-COMPLIANCE OBJECT-GROUP mib-2
netscreenVR

Defined Objects

nsOspf 1.3.6.1.4.1.3224.18.2
The MIB module to describe the NS-OSPF Version 2 Protocol
MODULE-IDENTITY    

nsOspfGeneralTable 1.3.6.1.4.1.3224.18.2.1
Ospf general information table per VR
OBJECT-TYPE    
  SEQUENCE OF  
    NsOspfGeneralEntry

nsOspfGeneralEntry 1.3.6.1.4.1.3224.18.2.1.1
Ospf general information table per VR
OBJECT-TYPE    
  NsOspfGeneralEntry  

nsOspfRouterId 1.3.6.1.4.1.3224.18.2.1.1.1
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
OBJECT-TYPE    
  RouterID  

nsOspfAdminStat 1.3.6.1.4.1.3224.18.2.1.1.2
The administrative status of OSPF in the router. The value 'enabled' denotes that the OSPF Process is active on at least one inter- face; 'disabled' disables it on all inter- faces.
OBJECT-TYPE    
  Status  

nsOspfVersionNumber 1.3.6.1.4.1.3224.18.2.1.1.3
The deprecated version number of the OSPF proto- col is 2.
OBJECT-TYPE    
  INTEGER version2(2)  

nsOspfAreaBdrRtrStatus 1.3.6.1.4.1.3224.18.2.1.1.4
A flag to note whether this router is an area border router.
OBJECT-TYPE    
  TruthValue  

nsOspfASBdrRtrStatus 1.3.6.1.4.1.3224.18.2.1.1.5
A flag to note whether this router is config- ured as an Autonomous System border router.
OBJECT-TYPE    
  TruthValue  

nsOspfExternLsaCount 1.3.6.1.4.1.3224.18.2.1.1.6
The number of external (LS type 5) link-state advertisements in the link-state database.
OBJECT-TYPE    
  Gauge32  

nsOspfExternLsaCksumSum 1.3.6.1.4.1.3224.18.2.1.1.7
The 32-bit unsigned sum of the LS checksums of the external link-state advertisements con- tained in the link-state database. This sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers.
OBJECT-TYPE    
  Integer32  

nsOspfTOSSupport 1.3.6.1.4.1.3224.18.2.1.1.8
The router's support for type-of-service rout- ing.
OBJECT-TYPE    
  TruthValue  

nsOspfOriginateNewLsas 1.3.6.1.4.1.3224.18.2.1.1.9
The number of new link-state advertisements that have been originated. This number is in- cremented each time the router originates a new LSA.
OBJECT-TYPE    
  Counter32  

nsOspfRxNewLsas 1.3.6.1.4.1.3224.18.2.1.1.10
The number of link-state advertisements re- ceived determined to be new instantiations. This number does not include newer instantia- tions of self-originated link-state advertise- ments.
OBJECT-TYPE    
  Counter32  

nsOspfExtLsdbLimit 1.3.6.1.4.1.3224.18.2.1.1.11
The maximum number of non-default AS- external-LSAs entries that can be stored in the link-state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches nsOspfExtLsdbLimit, the router enters Overflow- State. The router never holds more than nsOspfExtLsdbLimit non-default AS-external-LSAs in its database. OspfExtLsdbLimit MUST be set identically in all routers attached to the OSPF backbone and/or any regular OSPF area. (i.e., OSPF stub areas and NSSAs are excluded).
OBJECT-TYPE    
  Integer32 -1..'7FFFFFFF'H  

nsOspfMulticastExtensions 1.3.6.1.4.1.3224.18.2.1.1.12
A Bit Mask indicating whether the router is forwarding IP multicast (Class D) datagrams based on the algorithms defined in the Multi- cast Extensions to OSPF. Bit 0, if set, indicates that the router can forward IP multicast datagrams in the router's directly attached areas (called intra-area mul- ticast routing). Bit 1, if set, indicates that the router can forward IP multicast datagrams between OSPF areas (called inter-area multicast routing). Bit 2, if set, indicates that the router can forward IP multicast datagrams between Auto- nomous Systems (called inter-AS multicast rout- ing). Only certain combinations of bit settings are allowed, namely: 0 (no multicast forwarding is enabled), 1 (intra-area multicasting only), 3 (intra-area and inter-area multicasting), 5 (intra-area and inter-AS multicasting) and 7 (multicasting everywhere). By default, no mul- ticast forwarding is enabled.
OBJECT-TYPE    
  Integer32  

nsOspfExitOverflowInterval 1.3.6.1.4.1.3224.18.2.1.1.13
The number of seconds that, after entering OverflowState, a router will attempt to leave OverflowState. This allows the router to again originate non-default AS-external-LSAs. When set to 0, the router will not leave Overflow- State until restarted.
OBJECT-TYPE    
  PositiveInteger  

nsOspfDemandExtensions 1.3.6.1.4.1.3224.18.2.1.1.14
The router's support for demand routing.
OBJECT-TYPE    
  TruthValue  

nsOspfGeneralVRID 1.3.6.1.4.1.3224.18.2.1.1.15
Virtual Router ID
OBJECT-TYPE    
  INTEGER 0..65535  

nsOspfAreaTable 1.3.6.1.4.1.3224.18.2.2
Information describing the configured parame- ters and cumulative statistics of the router's attached areas.
OBJECT-TYPE    
  SEQUENCE OF  
    NsOspfAreaEntry

nsOspfAreaEntry 1.3.6.1.4.1.3224.18.2.2.1
Information describing the configured parame- ters and cumulative statistics of one of the router's attached areas.
OBJECT-TYPE    
  NsOspfAreaEntry  

nsOspfAreaId 1.3.6.1.4.1.3224.18.2.2.1.1
A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone.
OBJECT-TYPE    
  AreaID  

nsOspfImportAsExtern 1.3.6.1.4.1.3224.18.2.2.1.3
The area's support for importing AS external link- state advertisements.
OBJECT-TYPE    
  INTEGER importExternal(1), importNoExternal(2), importNssa(3)  

nsOspfSpfRuns 1.3.6.1.4.1.3224.18.2.2.1.4
The number of times that the intra-area route table has been calculated using this area's link-state database. This is typically done using Dijkstra's algorithm.
OBJECT-TYPE    
  Counter32  

nsOspfAreaBdrRtrCount 1.3.6.1.4.1.3224.18.2.2.1.5
The total number of area border routers reach- able within this area. This is initially zero, and is calculated in each SPF Pass.
OBJECT-TYPE    
  Gauge32  

nsOspfAsBdrRtrCount 1.3.6.1.4.1.3224.18.2.2.1.6
The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass.
OBJECT-TYPE    
  Gauge32  

nsOspfAreaLsaCount 1.3.6.1.4.1.3224.18.2.2.1.7
The total number of link-state advertisements in this area's link-state database, excluding AS External LSA's.
OBJECT-TYPE    
  Gauge32  

nsOspfAreaLsaCksumSum 1.3.6.1.4.1.3224.18.2.2.1.8
The 32-bit unsigned sum of the link-state ad- vertisements' LS checksums contained in this area's link-state database. This sum excludes external (LS type 5) link-state advertisements. The sum can be used to determine if there has been a change in a router's link state data- base, and to compare the link-state database of two routers.
OBJECT-TYPE    
  Integer32  

nsOspfAreaSummary 1.3.6.1.4.1.3224.18.2.2.1.9
The variable nsOspfAreaSummary controls the im- port of summary LSAs into stub areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate summary LSAs into the stub area. It will rely entirely on its de- fault route. If it is sendAreaSummary, the router will both summarize and propagate summary LSAs.
OBJECT-TYPE    
  INTEGER noAreaSummary(1), sendAreaSummary(2)  

nsOspfAreaStatus 1.3.6.1.4.1.3224.18.2.2.1.10
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

nsOspfAreaVRID 1.3.6.1.4.1.3224.18.2.2.1.11
Virtual Router ID
OBJECT-TYPE    
  INTEGER 0..65535  

nsOspfStubAreaTable 1.3.6.1.4.1.3224.18.2.3
The set of metrics that will be advertised by a default Area Border Router into a stub area.
OBJECT-TYPE    
  SEQUENCE OF  
    NsOspfStubAreaEntry

nsOspfStubAreaEntry 1.3.6.1.4.1.3224.18.2.3.1
The metric for a given Type of Service that will be advertised by a default Area Border Router into a stub area.
OBJECT-TYPE    
  NsOspfStubAreaEntry  

nsOspfStubAreaId 1.3.6.1.4.1.3224.18.2.3.1.1
The 32 bit identifier for the Stub Area. On creation, this can be derived from the in- stance.
OBJECT-TYPE    
  AreaID  

nsOspfStubTOS 1.3.6.1.4.1.3224.18.2.3.1.2
The Type of Service associated with the metric. On creation, this can be derived from the instance.
OBJECT-TYPE    
  TOSType  

nsOspfStubMetric 1.3.6.1.4.1.3224.18.2.3.1.3
The metric value applied at the indicated type of service. By default, this equals the least metric at the type of service among the inter- faces to other areas.
OBJECT-TYPE    
  BigMetric  

nsOspfStubStatus 1.3.6.1.4.1.3224.18.2.3.1.4
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

nsOspfStubMetricType 1.3.6.1.4.1.3224.18.2.3.1.5
This variable displays the type of metric ad- vertised as a default route.
OBJECT-TYPE    
  INTEGER nsOspfMetric(1), comparableCost(2), nonComparable(3)  

nsOspfStubVRID 1.3.6.1.4.1.3224.18.2.3.1.6
Virtual Router ID
OBJECT-TYPE    
  INTEGER 0..65535  

nsOspfLsdbTable 1.3.6.1.4.1.3224.18.2.4
The OSPF Process's Link State Database.
OBJECT-TYPE    
  SEQUENCE OF  
    NsOspfLsdbEntry

nsOspfLsdbEntry 1.3.6.1.4.1.3224.18.2.4.1
A single Link State Advertisement.
OBJECT-TYPE    
  NsOspfLsdbEntry  

nsOspfLsdbAreaId 1.3.6.1.4.1.3224.18.2.4.1.1
The 32 bit identifier of the Area from which the LSA was received.
OBJECT-TYPE    
  AreaID  

nsOspfLsdbType 1.3.6.1.4.1.3224.18.2.4.1.2
The type of the link state advertisement. Each link state type has a separate advertise- ment format.
OBJECT-TYPE    
  INTEGER routerLink(1), networkLink(2), summaryLink(3), asSummaryLink(4), asExternalLink(5), multicastLink(6), nssaExternalLink(7)  

nsOspfLsdbLsid 1.3.6.1.4.1.3224.18.2.4.1.3
The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
OBJECT-TYPE    
  IpAddress  

nsOspfLsdbRouterId 1.3.6.1.4.1.3224.18.2.4.1.4
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
OBJECT-TYPE    
  RouterID  

nsOspfLsdbSequence 1.3.6.1.4.1.3224.18.2.4.1.5
The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
OBJECT-TYPE    
  Integer32  

nsOspfLsdbAge 1.3.6.1.4.1.3224.18.2.4.1.6
This field is the age of the link state adver- tisement in seconds.
OBJECT-TYPE    
  Integer32  

nsOspfLsdbChecksum 1.3.6.1.4.1.3224.18.2.4.1.7
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
OBJECT-TYPE    
  Integer32  

nsOspfLsdbAdvertisement 1.3.6.1.4.1.3224.18.2.4.1.8
The entire Link State Advertisement, including its header.
OBJECT-TYPE    
  OCTET STRING SIZE(1..65535)  

nsOspfLsdbVRID 1.3.6.1.4.1.3224.18.2.4.1.9
Virtual Router ID
OBJECT-TYPE    
  INTEGER 0..65535  

nsOspfHostTable 1.3.6.1.4.1.3224.18.2.6
The list of Hosts, and their metrics, that the router will advertise as host routes.
OBJECT-TYPE    
  SEQUENCE OF  
    NsOspfHostEntry

nsOspfHostEntry 1.3.6.1.4.1.3224.18.2.6.1
A metric to be advertised, for a given type of service, when a given host is reachable.
OBJECT-TYPE    
  NsOspfHostEntry  

nsOspfHostIpAddress 1.3.6.1.4.1.3224.18.2.6.1.1
The IP Address of the Host.
OBJECT-TYPE    
  IpAddress  

nsOspfHostTOS 1.3.6.1.4.1.3224.18.2.6.1.2
The Type of Service of the route being config- ured.
OBJECT-TYPE    
  TOSType  

nsOspfHostMetric 1.3.6.1.4.1.3224.18.2.6.1.3
The Metric to be advertised.
OBJECT-TYPE    
  Metric  

nsOspfHostStatus 1.3.6.1.4.1.3224.18.2.6.1.4
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

nsOspfHostAreaID 1.3.6.1.4.1.3224.18.2.6.1.5
The Area the Host Entry is to be found within. By default, the area that a subsuming OSPF in- terface is in, or 0.0.0.0
OBJECT-TYPE    
  AreaID  

nsOspfHostVRID 1.3.6.1.4.1.3224.18.2.6.1.6
Virtual Router ID
OBJECT-TYPE    
  INTEGER 0..65535  

nsOspfIfTable 1.3.6.1.4.1.3224.18.2.7
The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF.
OBJECT-TYPE    
  SEQUENCE OF  
    NsOspfIfEntry

nsOspfIfEntry 1.3.6.1.4.1.3224.18.2.7.1
The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF.
OBJECT-TYPE    
  NsOspfIfEntry  

nsOspfIfIpAddress 1.3.6.1.4.1.3224.18.2.7.1.1
The IP address of this OSPF interface.
OBJECT-TYPE    
  IpAddress  

nsOspfAddressLessIf 1.3.6.1.4.1.3224.18.2.7.1.2
For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address.
OBJECT-TYPE    
  Integer32  

nsOspfIfAreaId 1.3.6.1.4.1.3224.18.2.7.1.3
A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.
OBJECT-TYPE    
  AreaID  

nsOspfIfType 1.3.6.1.4.1.3224.18.2.7.1.4
The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broad- cast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25 and similar technologies take the value 'nbma', and links that are definitively point to point take the value 'pointToPoint'.
OBJECT-TYPE    
  INTEGER broadcast(1), nbma(2), pointToPoint(3), pointToMultipoint(5)  

nsOspfIfAdminStat 1.3.6.1.4.1.3224.18.2.7.1.5
The OSPF interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.
OBJECT-TYPE    
  Status  

nsOspfIfRtrPriority 1.3.6.1.4.1.3224.18.2.7.1.6
The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker.
OBJECT-TYPE    
  DesignatedRouterPriority  

nsOspfIfTransitDelay 1.3.6.1.4.1.3224.18.2.7.1.7
The estimated number of seconds it takes to transmit a link state update packet over this interface.
OBJECT-TYPE    
  UpToMaxAge  

nsOspfIfRetransInterval 1.3.6.1.4.1.3224.18.2.7.1.8
The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets.
OBJECT-TYPE    
  UpToMaxAge  

nsOspfIfHelloInterval 1.3.6.1.4.1.3224.18.2.7.1.9
The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a common network.
OBJECT-TYPE    
  HelloRange  

nsOspfIfRtrDeadInterval 1.3.6.1.4.1.3224.18.2.7.1.10
The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
OBJECT-TYPE    
  PositiveInteger  

nsOspfIfPollInterval 1.3.6.1.4.1.3224.18.2.7.1.11
The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor.
OBJECT-TYPE    
  PositiveInteger  

nsOspfIfState 1.3.6.1.4.1.3224.18.2.7.1.12
The OSPF Interface State.
OBJECT-TYPE    
  INTEGER down(1), loopback(2), waiting(3), pointToPoint(4), designatedRouter(5), backupDesignatedRouter(6), otherDesignatedRouter(7)  

nsOspfIfDesignatedRouter 1.3.6.1.4.1.3224.18.2.7.1.13
The IP Address of the Designated Router.
OBJECT-TYPE    
  IpAddress  

nsOspfIfBackupDesignatedRouter 1.3.6.1.4.1.3224.18.2.7.1.14
The IP Address of the Backup Designated Router.
OBJECT-TYPE    
  IpAddress  

nsOspfIfEvents 1.3.6.1.4.1.3224.18.2.7.1.15
The number of times this OSPF interface has changed its state, or an error has occurred.
OBJECT-TYPE    
  Counter32  

nsOspfIfAuthKey 1.3.6.1.4.1.3224.18.2.7.1.16
The Authentication Key. If the Area's Author- ization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, nsOspfIfAuthKey always returns an Oc- tet String of length zero.
OBJECT-TYPE    
  OCTET STRING SIZE(0..256)  

nsOspfIfStatus 1.3.6.1.4.1.3224.18.2.7.1.17
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

nsOspfIfMulticastForwarding 1.3.6.1.4.1.3224.18.2.7.1.18
The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting nsOspfMulticastForwarding to 0 effective- ly disables all multicast forwarding.
OBJECT-TYPE    
  INTEGER blocked(1), multicast(2), unicast(3)  

nsOspfIfDemand 1.3.6.1.4.1.3224.18.2.7.1.19
Indicates whether Demand OSPF procedures (hel- lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this interface.
OBJECT-TYPE    
  TruthValue  

nsOspfIfAuthType 1.3.6.1.4.1.3224.18.2.7.1.20
The authentication type specified for an in- terface. Additional authentication types may be assigned locally.
OBJECT-TYPE    
  INTEGER 0..255  

nsOspfIfVRID 1.3.6.1.4.1.3224.18.2.7.1.21
Virtual Router ID
OBJECT-TYPE    
  INTEGER 0..65535  

nsOspfIfMetricTable 1.3.6.1.4.1.3224.18.2.8
The TOS metrics for a non-virtual interface identified by the interface index.
OBJECT-TYPE    
  SEQUENCE OF  
    NsOspfIfMetricEntry

nsOspfIfMetricEntry 1.3.6.1.4.1.3224.18.2.8.1
A particular TOS metric for a non-virtual in- terface identified by the interface index.
OBJECT-TYPE    
  NsOspfIfMetricEntry  

nsOspfIfMetricIpAddress 1.3.6.1.4.1.3224.18.2.8.1.1
The IP address of this OSPF interface. On row creation, this can be derived from the in- stance.
OBJECT-TYPE    
  IpAddress  

nsOspfIfMetricAddressLessIf 1.3.6.1.4.1.3224.18.2.8.1.2
For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the value of ifIndex for in- terfaces having no IP Address. On row crea- tion, this can be derived from the instance.
OBJECT-TYPE    
  Integer32  

nsOspfIfMetricTOS 1.3.6.1.4.1.3224.18.2.8.1.3
The type of service metric being referenced. On row creation, this can be derived from the instance.
OBJECT-TYPE    
  TOSType  

nsOspfIfMetricValue 1.3.6.1.4.1.3224.18.2.8.1.4
The metric of using this type of service on this interface. The default value of the TOS 0 Metric is 10^8 / ifSpeed.
OBJECT-TYPE    
  Metric  

nsOspfIfMetricStatus 1.3.6.1.4.1.3224.18.2.8.1.5
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

nsOspfIfMetricVRID 1.3.6.1.4.1.3224.18.2.8.1.6
Virtual Router ID
OBJECT-TYPE    
  INTEGER 0..65535  

nsOspfVirtIfTable 1.3.6.1.4.1.3224.18.2.9
Information about this router's virtual inter- faces.
OBJECT-TYPE    
  SEQUENCE OF  
    NsOspfVirtIfEntry

nsOspfVirtIfEntry 1.3.6.1.4.1.3224.18.2.9.1
Information about a single Virtual Interface.
OBJECT-TYPE    
  NsOspfVirtIfEntry  

nsOspfVirtIfAreaId 1.3.6.1.4.1.3224.18.2.9.1.1
The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0
OBJECT-TYPE    
  AreaID  

nsOspfVirtIfNeighbor 1.3.6.1.4.1.3224.18.2.9.1.2
The Router ID of the Virtual Neighbor.
OBJECT-TYPE    
  RouterID  

nsOspfVirtIfTransitDelay 1.3.6.1.4.1.3224.18.2.9.1.3
The estimated number of seconds it takes to transmit a link- state update packet over this interface.
OBJECT-TYPE    
  UpToMaxAge  

nsOspfVirtIfRetransInterval 1.3.6.1.4.1.3224.18.2.9.1.4
The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. This value should be well over the expected round- trip time.
OBJECT-TYPE    
  UpToMaxAge  

nsOspfVirtIfHelloInterval 1.3.6.1.4.1.3224.18.2.9.1.5
The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor.
OBJECT-TYPE    
  HelloRange  

nsOspfVirtIfRtrDeadInterval 1.3.6.1.4.1.3224.18.2.9.1.6
The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neigh- bor.
OBJECT-TYPE    
  PositiveInteger  

nsOspfVirtIfState 1.3.6.1.4.1.3224.18.2.9.1.7
OSPF virtual interface states.
OBJECT-TYPE    
  INTEGER down(1), pointToPoint(4)  

nsOspfVirtIfEvents 1.3.6.1.4.1.3224.18.2.9.1.8
The number of state changes or error events on this Virtual Link
OBJECT-TYPE    
  Counter32  

nsOspfVirtIfAuthKey 1.3.6.1.4.1.3224.18.2.9.1.9
If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 oc- tets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, nsOspfVifAuthKey always returns a string of length zero.
OBJECT-TYPE    
  OCTET STRING SIZE(0..256)  

nsOspfVirtIfStatus 1.3.6.1.4.1.3224.18.2.9.1.10
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

nsOspfVirtIfAuthType 1.3.6.1.4.1.3224.18.2.9.1.11
The authentication type specified for a virtu- al interface. Additional authentication types may be assigned locally.
OBJECT-TYPE    
  INTEGER 0..255  

nsOspfVirtIfVRID 1.3.6.1.4.1.3224.18.2.9.1.12
Virtual Router ID
OBJECT-TYPE    
  INTEGER 0..65535  

nsOspfNbrTable 1.3.6.1.4.1.3224.18.2.10
A table of non-virtual neighbor information.
OBJECT-TYPE    
  SEQUENCE OF  
    NsOspfNbrEntry

nsOspfNbrEntry 1.3.6.1.4.1.3224.18.2.10.1
The information regarding a single neighbor.
OBJECT-TYPE    
  NsOspfNbrEntry  

nsOspfNbrIpAddr 1.3.6.1.4.1.3224.18.2.10.1.1
The IP address this neighbor is using in its IP Source Address. Note that, on addressless links, this will not be 0.0.0.0, but the ad- dress of another of the neighbor's interfaces.
OBJECT-TYPE    
  IpAddress  

nsOspfNbrAddressLessIndex 1.3.6.1.4.1.3224.18.2.10.1.2
On an interface having an IP Address, zero. On addressless interfaces, the corresponding value of ifIndex in the Internet Standard MIB. On row creation, this can be derived from the instance.
OBJECT-TYPE    
  InterfaceIndex  

nsOspfNbrRtrId 1.3.6.1.4.1.3224.18.2.10.1.3
A 32-bit integer (represented as a type IpAd- dress) uniquely identifying the neighboring router in the Autonomous System.
OBJECT-TYPE    
  RouterID  

nsOspfNbrOptions 1.3.6.1.4.1.3224.18.2.10.1.4
A Bit Mask corresponding to the neighbor's op- tions field. Bit 0, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 1, if set, indicates that the associated area accepts and operates on external informa- tion; if zero, it is a stub area. Bit 2, if set, indicates that the system is ca- pable of routing IP Multicast datagrams; i.e., that it implements the Multicast Extensions to OSPF. Bit 3, if set, indicates that the associated area is an NSSA. These areas are capable of carrying type 7 external advertisements, which are translated into type 5 external advertise- ments at NSSA borders.
OBJECT-TYPE    
  Integer32  

nsOspfNbrPriority 1.3.6.1.4.1.3224.18.2.10.1.5
The priority of this neighbor in the designat- ed router election algorithm. The value 0 sig- nifies that the neighbor is not eligible to be- come the designated router on this particular network.
OBJECT-TYPE    
  DesignatedRouterPriority  

nsOspfNbrState 1.3.6.1.4.1.3224.18.2.10.1.6
The State of the relationship with this Neigh- bor.
OBJECT-TYPE    
  INTEGER down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)  

nsOspfNbrEvents 1.3.6.1.4.1.3224.18.2.10.1.7
The number of times this neighbor relationship has changed state, or an error has occurred.
OBJECT-TYPE    
  Counter32  

nsOspfNbrLsRetransQLen 1.3.6.1.4.1.3224.18.2.10.1.8
The deprecated length of the retransmission queue.
OBJECT-TYPE    
  Gauge32  

nsOspfNbmaNbrStatus 1.3.6.1.4.1.3224.18.2.10.1.9
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

nsOspfNbmaNbrPermanence 1.3.6.1.4.1.3224.18.2.10.1.10
This variable displays the status of the en- try. 'dynamic' and 'permanent' refer to how the neighbor became known.
OBJECT-TYPE    
  INTEGER dynamic(1), permanent(2)  

nsOspfNbrHelloSuppressed 1.3.6.1.4.1.3224.18.2.10.1.11
Indicates whether Hellos are being suppressed to the neighbor
OBJECT-TYPE    
  TruthValue  

nsOspfNbrVRID 1.3.6.1.4.1.3224.18.2.10.1.12
Virtual Router ID
OBJECT-TYPE    
  INTEGER 0..65535  

nsOspfVirtNbrTable 1.3.6.1.4.1.3224.18.2.11
A table of virtual neighbor information.
OBJECT-TYPE    
  SEQUENCE OF  
    NsOspfVirtNbrEntry

nsOspfVirtNbrEntry 1.3.6.1.4.1.3224.18.2.11.1
Virtual neighbor information.
OBJECT-TYPE    
  NsOspfVirtNbrEntry  

nsOspfVirtNbrArea 1.3.6.1.4.1.3224.18.2.11.1.1
The Transit Area Identifier.
OBJECT-TYPE    
  AreaID  

nsOspfVirtNbrRtrId 1.3.6.1.4.1.3224.18.2.11.1.2
A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.
OBJECT-TYPE    
  RouterID  

nsOspfVirtNbrIpAddr 1.3.6.1.4.1.3224.18.2.11.1.3
The IP address this Virtual Neighbor is us- ing.
OBJECT-TYPE    
  IpAddress  

nsOspfVirtNbrOptions 1.3.6.1.4.1.3224.18.2.11.1.4
A Bit Mask corresponding to the neighbor's op- tions field. Bit 1, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 2, if set, indicates that the system is Network Multicast capable; ie, that it imple- ments OSPF Multicast Routing.
OBJECT-TYPE    
  Integer32  

nsOspfVirtNbrState 1.3.6.1.4.1.3224.18.2.11.1.5
The state of the Virtual Neighbor Relation- ship.
OBJECT-TYPE    
  INTEGER down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)  

nsOspfVirtNbrEvents 1.3.6.1.4.1.3224.18.2.11.1.6
The number of times this virtual link has changed its state, or an error has occurred.
OBJECT-TYPE    
  Counter32  

nsOspfVirtNbrLsRetransQLen 1.3.6.1.4.1.3224.18.2.11.1.7
The deprecated length of the retransmission queue.
OBJECT-TYPE    
  Gauge32  

nsOspfVirtNbrHelloSuppressed 1.3.6.1.4.1.3224.18.2.11.1.8
Indicates whether Hellos are being suppressed to the neighbor
OBJECT-TYPE    
  TruthValue  

nsOspfVirtNbrVRID 1.3.6.1.4.1.3224.18.2.11.1.9
Virtual Router ID
OBJECT-TYPE    
  INTEGER 0..65535  

nsOspfExtLsdbTable 1.3.6.1.4.1.3224.18.2.12
The OSPF Process's Links State Database.
OBJECT-TYPE    
  SEQUENCE OF  
    NsOspfExtLsdbEntry

nsOspfExtLsdbEntry 1.3.6.1.4.1.3224.18.2.12.1
A single Link State Advertisement.
OBJECT-TYPE    
  NsOspfExtLsdbEntry  

nsOspfExtLsdbType 1.3.6.1.4.1.3224.18.2.12.1.1
The type of the link state advertisement. Each link state type has a separate advertise- ment format.
OBJECT-TYPE    
  INTEGER asExternalLink(5)  

nsOspfExtLsdbLsid 1.3.6.1.4.1.3224.18.2.12.1.2
The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
OBJECT-TYPE    
  IpAddress  

nsOspfExtLsdbRouterId 1.3.6.1.4.1.3224.18.2.12.1.3
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
OBJECT-TYPE    
  RouterID  

nsOspfExtLsdbSequence 1.3.6.1.4.1.3224.18.2.12.1.4
The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
OBJECT-TYPE    
  Integer32  

nsOspfExtLsdbAge 1.3.6.1.4.1.3224.18.2.12.1.5
This field is the age of the link state adver- tisement in seconds.
OBJECT-TYPE    
  Integer32  

nsOspfExtLsdbChecksum 1.3.6.1.4.1.3224.18.2.12.1.6
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
OBJECT-TYPE    
  Integer32  

nsOspfExtLsdbAdvertisement 1.3.6.1.4.1.3224.18.2.12.1.7
The entire Link State Advertisement, including its header.
OBJECT-TYPE    
  OCTET STRING SIZE(36)  

nsOspfExtLsdbVRID 1.3.6.1.4.1.3224.18.2.12.1.8
Virtual Router ID
OBJECT-TYPE    
  INTEGER 0..65535  

nsOspfAreaAggregateTable 1.3.6.1.4.1.3224.18.2.14
A range of IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255. Note that if ranges are configured such that one range sub- sumes another range (e.g., 10.0.0.0 mask 255.0.0.0 and 10.1.0.0 mask 255.255.0.0), the most specific match is the preferred one.
OBJECT-TYPE    
  SEQUENCE OF  
    NsOspfAreaAggregateEntry

nsOspfAreaAggregateEntry 1.3.6.1.4.1.3224.18.2.14.1
A range of IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255. Note that if ranges are range configured such that one range subsumes another range (e.g., 10.0.0.0 mask 255.0.0.0 and 10.1.0.0 mask 255.255.0.0), the most specific match is the preferred one.
OBJECT-TYPE    
  NsOspfAreaAggregateEntry  

nsOspfAreaAggregateAreaID 1.3.6.1.4.1.3224.18.2.14.1.1
The Area the Address Aggregate is to be found within.
OBJECT-TYPE    
  AreaID  

nsOspfAreaAggregateLsdbType 1.3.6.1.4.1.3224.18.2.14.1.2
The type of the Address Aggregate. This field specifies the Lsdb type that this Address Ag- gregate applies to.
OBJECT-TYPE    
  INTEGER summaryLink(3), nssaExternalLink(7)  

nsOspfAreaAggregateNet 1.3.6.1.4.1.3224.18.2.14.1.3
The IP Address of the Net or Subnet indicated by the range.
OBJECT-TYPE    
  IpAddress  

nsOspfAreaAggregateMask 1.3.6.1.4.1.3224.18.2.14.1.4
The Subnet Mask that pertains to the Net or Subnet.
OBJECT-TYPE    
  IpAddress  

nsOspfAreaAggregateStatus 1.3.6.1.4.1.3224.18.2.14.1.5
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

nsOspfAreaAggregateEffect 1.3.6.1.4.1.3224.18.2.14.1.6
Subnets subsumed by ranges either trigger the advertisement of the indicated aggregate (ad- vertiseMatching), or result in the subnet's not being advertised at all outside the area.
OBJECT-TYPE    
  INTEGER advertiseMatching(1), doNotAdvertiseMatching(2)  

nsOspfAreaAggregateVRID 1.3.6.1.4.1.3224.18.2.14.1.7
Virtual Router ID
OBJECT-TYPE    
  INTEGER 0..65535  

Defined Objects

AreaID  
An OSPF Area Identifier.
TEXTUAL-CONVENTION    
  IpAddress  

RouterID  
A OSPF Router Identifier.
TEXTUAL-CONVENTION    
  IpAddress  

Metric  
The OSPF Internal Metric.
TEXTUAL-CONVENTION    
  Integer32 0..'FFFF'H  

BigMetric  
The OSPF External Metric.
TEXTUAL-CONVENTION    
  Integer32 0..'FFFFFF'H  

Status  
The status of an interface: 'enabled' indicates that it is willing to communicate with other OSPF Routers, while 'disabled' indicates that it is not.
TEXTUAL-CONVENTION    
  INTEGER enabled(1), disabled(2)  

PositiveInteger  
A positive integer. Values in excess are precluded as unnecessary and prone to interoperability issues.
TEXTUAL-CONVENTION    
  Integer32 0..'7FFFFFFF'H  

HelloRange  
The range of intervals on which hello messages are exchanged.
TEXTUAL-CONVENTION    
  Integer32 1..'FFFF'H  

UpToMaxAge  
The values that one might find or configure for variables bounded by the maximum age of an LSA.
TEXTUAL-CONVENTION    
  Integer32 0..3600  

InterfaceIndex  
The range of ifIndex.
TEXTUAL-CONVENTION    
  Integer32  

DesignatedRouterPriority  
The values defined for the priority of a system for becoming the designated router.
TEXTUAL-CONVENTION    
  Integer32 0..'FF'H  

TOSType  
Type of Service is defined as a mapping to the IP Type of Service Flags as defined in the IP Forwarding Table MIB +-----+-----+-----+-----+-----+-----+-----+-----+ | | | | | PRECEDENCE | TYPE OF SERVICE | 0 | | | | | +-----+-----+-----+-----+-----+-----+-----+-----+ IP TOS IP TOS Field Policy Field Policy Contents Code Contents Code 0 0 0 0 ==> 0 0 0 0 1 ==> 2 0 0 1 0 ==> 4 0 0 1 1 ==> 6 0 1 0 0 ==> 8 0 1 0 1 ==> 10 0 1 1 0 ==> 12 0 1 1 1 ==> 14 1 0 0 0 ==> 16 1 0 0 1 ==> 18 1 0 1 0 ==> 20 1 0 1 1 ==> 22 1 1 0 0 ==> 24 1 1 0 1 ==> 26 1 1 1 0 ==> 28 1 1 1 1 ==> 30 The remaining values are left for future definition.
TEXTUAL-CONVENTION    
  Integer32 0..30  

NsOspfGeneralEntry  
SEQUENCE    
  RouterID as nsOspfRouterId  
  Status as nsOspfAdminStat  
  INTEGER as nsOspfVersionNumber  
  TruthValue as nsOspfAreaBdrRtrStatus  
  TruthValue as nsOspfASBdrRtrStatus  
  Gauge32 as nsOspfExternLsaCount  
  Gauge32 as nsOspfAreaLsaCount  
  Integer32 as nsOspfExternLsaCksumSum  
  TruthValue as nsOspfTOSSupport  
  Counter32 as nsOspfOriginateNewLsas  
  Counter32 as nsOspfRxNewLsas  
  Integer32 as nsOspfExtLsdbLimit  
  Integer32 as nsOspfMulticastExtensions  
  PositiveInteger as nsOspfExitOverflowInterval  
  TruthValue as nsOspfDemandExtensions  
  INTEGER as nsOspfGeneralVRID  

NsOspfAreaEntry  
SEQUENCE    
  AreaID as nsOspfAreaId  
  INTEGER as nsOspfImportAsExtern  
  Counter32 as nsOspfSpfRuns  
  Gauge32 as nsOspfAreaBdrRtrCount  
  Gauge32 as nsOspfAsBdrRtrCount  
  Gauge32 as nsOspfAreaLsaCount  
  Integer32 as nsOspfAreaLsaCksumSum  
  INTEGER as nsOspfAreaSummary  
  RowStatus as nsOspfAreaStatus  
  INTEGER as nsOspfAreaVRID  

NsOspfStubAreaEntry  
SEQUENCE    
  AreaID as nsOspfStubAreaId  
  TOSType as nsOspfStubTOS  
  BigMetric as nsOspfStubMetric  
  RowStatus as nsOspfStubStatus  
  INTEGER as nsOspfStubMetricType  
  INTEGER as nsOspfStubVRID  

NsOspfLsdbEntry  
SEQUENCE    
  AreaID as nsOspfLsdbAreaId  
  INTEGER as nsOspfLsdbType  
  IpAddress as nsOspfLsdbLsid  
  RouterID as nsOspfLsdbRouterId  
  Integer32 as nsOspfLsdbSequence  
  Integer32 as nsOspfLsdbAge  
  Integer32 as nsOspfLsdbChecksum  
  OCTET STRING as nsOspfLsdbAdvertisement  
  INTEGER as nsOspfLsdbVRID  

NsOspfHostEntry  
SEQUENCE    
  IpAddress as nsOspfHostIpAddress  
  TOSType as nsOspfHostTOS  
  Metric as nsOspfHostMetric  
  RowStatus as nsOspfHostStatus  
  AreaID as nsOspfHostAreaID  
  INTEGER as nsOspfHostVRID  

NsOspfIfEntry  
SEQUENCE    
  IpAddress as nsOspfIfIpAddress  
  Integer32 as nsOspfAddressLessIf  
  AreaID as nsOspfIfAreaId  
  INTEGER as nsOspfIfType  
  Status as nsOspfIfAdminStat  
  DesignatedRouterPriority as nsOspfIfRtrPriority  
  UpToMaxAge as nsOspfIfTransitDelay  
  UpToMaxAge as nsOspfIfRetransInterval  
  HelloRange as nsOspfIfHelloInterval  
  PositiveInteger as nsOspfIfRtrDeadInterval  
  PositiveInteger as nsOspfIfPollInterval  
  INTEGER as nsOspfIfState  
  IpAddress as nsOspfIfDesignatedRouter  
  IpAddress as nsOspfIfBackupDesignatedRouter  
  Counter32 as nsOspfIfEvents  
  INTEGER as nsOspfIfAuthType  
  OCTET STRING as nsOspfIfAuthKey  
  RowStatus as nsOspfIfStatus  
  INTEGER as nsOspfIfMulticastForwarding  
  TruthValue as nsOspfIfDemand  
  INTEGER as nsOspfIfVRID  

NsOspfIfMetricEntry  
SEQUENCE    
  IpAddress as nsOspfIfMetricIpAddress  
  Integer32 as nsOspfIfMetricAddressLessIf  
  TOSType as nsOspfIfMetricTOS  
  Metric as nsOspfIfMetricValue  
  RowStatus as nsOspfIfMetricStatus  
  INTEGER as nsOspfIfMetricVRID  

NsOspfVirtIfEntry  
SEQUENCE    
  AreaID as nsOspfVirtIfAreaId  
  RouterID as nsOspfVirtIfNeighbor  
  UpToMaxAge as nsOspfVirtIfTransitDelay  
  UpToMaxAge as nsOspfVirtIfRetransInterval  
  HelloRange as nsOspfVirtIfHelloInterval  
  PositiveInteger as nsOspfVirtIfRtrDeadInterval  
  INTEGER as nsOspfVirtIfState  
  Counter32 as nsOspfVirtIfEvents  
  INTEGER as nsOspfVirtIfAuthType  
  OCTET STRING as nsOspfVirtIfAuthKey  
  RowStatus as nsOspfVirtIfStatus  
  INTEGER as nsOspfVirtIfVRID  

NsOspfNbrEntry  
SEQUENCE    
  IpAddress as nsOspfNbrIpAddr  
  InterfaceIndex as nsOspfNbrAddressLessIndex  
  RouterID as nsOspfNbrRtrId  
  Integer32 as nsOspfNbrOptions  
  DesignatedRouterPriority as nsOspfNbrPriority  
  INTEGER as nsOspfNbrState  
  Counter32 as nsOspfNbrEvents  
  Gauge32 as nsOspfNbrLsRetransQLen  
  RowStatus as nsOspfNbmaNbrStatus  
  INTEGER as nsOspfNbmaNbrPermanence  
  TruthValue as nsOspfNbrHelloSuppressed  
  INTEGER as nsOspfNbrVRID  

NsOspfVirtNbrEntry  
SEQUENCE    
  AreaID as nsOspfVirtNbrArea  
  RouterID as nsOspfVirtNbrRtrId  
  IpAddress as nsOspfVirtNbrIpAddr  
  Integer32 as nsOspfVirtNbrOptions  
  INTEGER as nsOspfVirtNbrState  
  Counter32 as nsOspfVirtNbrEvents  
  Gauge32 as nsOspfVirtNbrLsRetransQLen  
  TruthValue as nsOspfVirtNbrHelloSuppressed  
  INTEGER as nsOspfVirtNbrVRID  

NsOspfExtLsdbEntry  
SEQUENCE    
  INTEGER as nsOspfExtLsdbType  
  IpAddress as nsOspfExtLsdbLsid  
  RouterID as nsOspfExtLsdbRouterId  
  Integer32 as nsOspfExtLsdbSequence  
  Integer32 as nsOspfExtLsdbAge  
  Integer32 as nsOspfExtLsdbChecksum  
  OCTET STRING as nsOspfExtLsdbAdvertisement  
  INTEGER as nsOspfExtLsdbVRID  

NsOspfAreaAggregateEntry  
SEQUENCE    
  AreaID as nsOspfAreaAggregateAreaID  
  INTEGER as nsOspfAreaAggregateLsdbType  
  IpAddress as nsOspfAreaAggregateNet  
  IpAddress as nsOspfAreaAggregateMask  
  RowStatus as nsOspfAreaAggregateStatus  
  INTEGER as nsOspfAreaAggregateEffect  
  INTEGER as nsOspfAreaAggregateVRID