NNCEXTPVC-MIB

File: NNCEXTPVC-MIB.mib (50845 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC IF-MIB
SNMPv2-CONF NNCGNI0001-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
TEXTUAL-CONVENTION RowStatus InterfaceIndex
MODULE-COMPLIANCE OBJECT-GROUP nncExtensions

Defined Objects

nncExtPvc 1.3.6.1.4.1.123.3.79
This module contains Alcatel's proprietary MIB definition for managing point-to-point and point-to-multipoint Permanent Virtual Connections (PVCs). The MIB supports the creation, modification, query and deletion of PVCs (Permanent Virtual Connections) on Cell Relay endpoints, both Permanent Virtual Path Connection (PVPC) and Permanent Virtual Channel Connection (PVCC) are supported. PVPCs are defined by nncCrPvpcTable and PVCCs are defined by nncCrPvccTable. PVPCs or PVCC's connecting different endpoint types, CR to FR, FR to CR, CR to CE, CE to CR, CE to FR or FR to CE are not suppported at this point. Resource connections such as Signalling, PNNI, ILMI and CPSS are also not supported. PVCs can be created by one of two ways: using rowStats as 'createAndGo' or using rowStatus as 'createAndWait'+'active'. In some cases, to create a PVC via this table requires two SET-REQs, because one SET-REQ PDU cannot fit all required objects. In these cases, the rowStatus is set to createAndWait(5) for the first 1 SET-REQ and set to active(1) for the last SET-REQ. In some cases, all required MIB objects can fit in one SET-REQ PDU. In these cases the rowStatus should be set to createAndGo(4) To delete a PVC, the SNMP manager should set rowStatus of the PVC instance to 'destroy'. Each PVC is modeled as set of entries in the PVC table. A point- to-point PVC is modeled as one entry; a point-to-multipoint (N leafs) is modeled as N entries in this table. The N entries of a point-to- multipoint PVC shares the same source end point. Some abreviations: abr/ABR/Abr: Available Bit Rate Bwd: Backward. For traffice descriptors from destination end point to source end point cbr/CBR/Cbr: Constant Bit Rate Dst: Dstination end point Fwd: Forward. For traffic descriptors from source end point to destination end point nt-vbr/ntvbr/NT-VBR: Non-Real-Time Variable Bit Rate p2p: Point-to-Point p2mp: Point-to-Multipoint Src: Source end point Targ: Target. For the destination end point info in source end point table ubr/UBR/Ubr: Unspecified Bit Rate VCI/Vci/vci: Virtual channel identifier VCL/Vcl/vcl: Virtual channel link VPI/Vpi/vpi: Virtual path identifier VPL/Vpl/Vpl: Virtual path link
MODULE-IDENTITY    

nncExtPvcObjects 1.3.6.1.4.1.123.3.79.1
OBJECT IDENTIFIER    

nncCrPvpcTable 1.3.6.1.4.1.123.3.79.1.1
nncCrPvpcTable contains all the objects sent to a source endpoint that are used to create, modify, delete and query PVC connections.
OBJECT-TYPE    
  SEQUENCE OF  
    NncCrPvpcTableEntry

nncCrPvpcTableEntry 1.3.6.1.4.1.123.3.79.1.1.1
An entry of nncCrPvpcTable
OBJECT-TYPE    
  NncCrPvpcTableEntry  

nncCrPvpcSrcIfIndex 1.3.6.1.4.1.123.3.79.1.1.1.1
This object contains the ifIndex value for the source endpoint
OBJECT-TYPE    
  InterfaceIndex  

nncCrPvpcSrcVpi 1.3.6.1.4.1.123.3.79.1.1.1.2
This object contains the VPI value for the source endpoint.
OBJECT-TYPE    
  INTEGER 0..4095  

nncCrPvpcDstIfIndex 1.3.6.1.4.1.123.3.79.1.1.1.3
This object contains the ifIndex value for the destination endpoint
OBJECT-TYPE    
  InterfaceIndex  

nncCrPvpcDstVpi 1.3.6.1.4.1.123.3.79.1.1.1.4
This object contains the VPI value for the destination endpoint.
OBJECT-TYPE    
  INTEGER 0..4095  

nncCrPvpcCastType 1.3.6.1.4.1.123.3.79.1.1.1.5
This object is used to indicate whether the PVPC is point-to-point or point-to-multipoint
OBJECT-TYPE    
  INTEGER p2p(1), p2mp(2)  

nncCrPvpcFwdServiceCategory 1.3.6.1.4.1.123.3.79.1.1.1.6
This object is used to set the traffic service category from source endpoint to destination endpoint. This object is dependent on the value specified in nncCrPvpcFwdTmTrafficDescripton object
OBJECT-TYPE    
  INTEGER cbr(1), nrtvbr(2), abr(3), ubr(4), rtvbr(6)  

nncCrPvpcBwdServiceCategory 1.3.6.1.4.1.123.3.79.1.1.1.7
This object is used to set the traffic service category from destination endpoint to source endpoint. This object is dependent on the value specified in nncCrPvpcBwdTmTrafficDescripton object
OBJECT-TYPE    
  INTEGER cbr(1), nrtvbr(2), abr(3), ubr(4), rtvbr(6)  

nncCrPvpcFwdAbrDynTrfcIcr 1.3.6.1.4.1.123.3.79.1.1.1.8
ABR dynamic traffic descriptor's Initial Cell Rate for the forward direction. Range: 0 - 2488320 Kb/s
OBJECT-TYPE    
  INTEGER 0..2488320  

nncCrPvpcFwdAbrDynTrfcRif 1.3.6.1.4.1.123.3.79.1.1.1.9
ABR traffic Rate Increase Factor for the forward direction. Value is expressed as the -power of 2. Range: 0 - 9
OBJECT-TYPE    
  INTEGER 0..9  

nncCrPvpcFwdAbrDynTrfcRdf 1.3.6.1.4.1.123.3.79.1.1.1.10
ABR traffic Rate Decrease Factor descriptor for the forward direction. Value is expressed as the -power of 2 Range: 0 - 9
OBJECT-TYPE    
  INTEGER 0..9  

nncCrPvpcBwdAbrDynTrfcIcr 1.3.6.1.4.1.123.3.79.1.1.1.11
ABR dynamic traffic descriptor's Initial Cell Rate for the destination endpoint. Range: 0 - 2488320 Kb/s
OBJECT-TYPE    
  INTEGER 0..2488320  

nncCrPvpcBwdAbrDynTrfcRif 1.3.6.1.4.1.123.3.79.1.1.1.12
ABR traffic Rate Increase Factor for the destination endpoint. Value is expressed as the -power of 2. Range: 0 - 9
OBJECT-TYPE    
  INTEGER 0..9  

nncCrPvpcBwdAbrDynTrfcRdf 1.3.6.1.4.1.123.3.79.1.1.1.13
ABR traffic Rate Decrease Factor descriptor for the destination endpoint. Value is expressed as the -power of 2 Range: 0 - 9
OBJECT-TYPE    
  INTEGER 0..9  

nncCrPvpcSrcBillingFlag 1.3.6.1.4.1.123.3.79.1.1.1.14
Billing Configuration for the source endpoint.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

nncCrPvpcDstBillingFlag 1.3.6.1.4.1.123.3.79.1.1.1.15
Billing Configuration for the destination endpoint.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

nncCrPvpcFwdTmTrafficDescriptor 1.3.6.1.4.1.123.3.79.1.1.1.16
This object contains the traffic descriptor for the SPVC. None (0) (Not applicable,the case of a P2MP leaf) Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0+1/S_0 (4) (NRT/RT-VBR only) P_0+1/M_0+1 (5) (ABR and UBR only)
OBJECT-TYPE    
  INTEGER none(0), tagAll(1), p0Plus1(2), p0Plus1SlashS0Plus1(3), p0Plus1SlashS0(4), p0Plus1SlashM0Plus1(5)  

nncCrPvpcFwdTmPolicingOption 1.3.6.1.4.1.123.3.79.1.1.1.17
Policing Option for a PVPC. The tag option is supported only on rt-VBR/nrt-VBR connections that use the P_0_1/S_0 traffic descriptor
OBJECT-TYPE    
  INTEGER none(0), disabled(1), tag(2), discard(3)  

nncCrPvpcFwdTmBucketOneRate 1.3.6.1.4.1.123.3.79.1.1.1.18
This object is used for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. Range: 0 - 2488320 Kb/s
OBJECT-TYPE    
  INTEGER 0..2488320  

nncCrPvpcFwdTmBucketOneCdvt 1.3.6.1.4.1.123.3.79.1.1.1.19
This object is used to set cell delay variation tolerance (CDVT) for one end point, measured in microseconds. Range: 1 - 190,000 microseconds
OBJECT-TYPE    
  INTEGER 1..190000  

nncCrPvpcFwdTmBucketTwoRate 1.3.6.1.4.1.123.3.79.1.1.1.20
SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range: 0 - 2488320 Kb/s
OBJECT-TYPE    
  INTEGER 0..2488320  

nncCrPvpcFwdTmBucketTwoMbs 1.3.6.1.4.1.123.3.79.1.1.1.21
This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrt-VBR and rt-VBR only). Range: 1 - 10000 cells
OBJECT-TYPE    
  INTEGER 1..10000  

nncCrPvpcFwdTmCdv 1.3.6.1.4.1.123.3.79.1.1.1.22
This value is to set the cell delay variation (CDV) between two PVC endpoints when using the rt-VBR service category.. Range: 250-10000 microseconds
OBJECT-TYPE    
  INTEGER 250..10000  

nncCrPvpcFwdTmClr 1.3.6.1.4.1.123.3.79.1.1.1.23
The object is to set the cell loss ratio (CLR) between two PVC endpoints when using the nrt-VBR service category. Value set as 1.0e-#
OBJECT-TYPE    
  INTEGER 1..7  

nncCrPvpcBwdTmTrafficDescriptor 1.3.6.1.4.1.123.3.79.1.1.1.24
This object contains the traffic descriptor for the PVC. None (0) (Not applicable,the case of a P2MP leaf) Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0+1/S_0 (4) (NRT/RT-VBR only) P_0+1/M_0+1 (5) (ABR and UBR only)
OBJECT-TYPE    
  INTEGER none(0), tagAll(1), p0Plus1(2), p0Plus1SlashS0Plus1(3), p0Plus1SlashS0(4), p0Plus1SlashM0Plus1(5)  

nncCrPvpcBwdTmPolicingOption 1.3.6.1.4.1.123.3.79.1.1.1.25
Policing Option for a PVPC. The tag option is supported only on rt-VBR/nrt-VBR connections that use the P_0_1/S_0 traffic descriptor
OBJECT-TYPE    
  INTEGER none(0), disabled(1), tag(2), discard(3)  

nncCrPvpcBwdTmBucketOneRate 1.3.6.1.4.1.123.3.79.1.1.1.26
This object is used for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. Range: 0 - 2488320 Kb/s
OBJECT-TYPE    
  INTEGER 0..2488320  

nncCrPvpcBwdTmBucketOneCdvt 1.3.6.1.4.1.123.3.79.1.1.1.27
This object is used to set cell delay variation tolerance (CDVT) for one end point, measured in microseconds. Range: 1 - 190,000 microseconds
OBJECT-TYPE    
  INTEGER 1..190000  

nncCrPvpcBwdTmBucketTwoRate 1.3.6.1.4.1.123.3.79.1.1.1.28
SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range: 0 - 2488320 Kb/s
OBJECT-TYPE    
  INTEGER 0..2488320  

nncCrPvpcBwdTmBucketTwoMbs 1.3.6.1.4.1.123.3.79.1.1.1.29
This object is to set the maximum burst size, in cells, for SIR_0p or SIR_0+1p. Used for burst traffic. Range: 1 - 10000 cells
OBJECT-TYPE    
  INTEGER 1..10000  

nncCrPvpcBwdTmCdv 1.3.6.1.4.1.123.3.79.1.1.1.30
This value is to set the cell delay variation (CDV) between two PVC endpoints when using the rt-VBR service category. Range: 250-10000 microseconds
OBJECT-TYPE    
  INTEGER 250..10000  

nncCrPvpcBwdTmClr 1.3.6.1.4.1.123.3.79.1.1.1.31
The object is to set the cell loss ratio (CLR) between two PVC endpoints when using the nrt-VBR service category. Value set as 1.0e-# Range: 1 - 7
OBJECT-TYPE    
  INTEGER 1..7  

nncCrPvpcSrcAlsConfig 1.3.6.1.4.1.123.3.79.1.1.1.32
This object is used to set OAM Alarm Surveillance configuration for the source endpoint.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

nncCrPvpcDstAlsConfig 1.3.6.1.4.1.123.3.79.1.1.1.33
This object is used to set OAM Alarm Surveillance configuration for the destination endpoint.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

nncCrPvpcCreator 1.3.6.1.4.1.123.3.79.1.1.1.34
The object retrieves the creator of a PVC connection.
OBJECT-TYPE    
  INTEGER unknown(0), nmti(1), nm5620(2), snmp(9)  

nncCrPvpcRowStatus 1.3.6.1.4.1.123.3.79.1.1.1.35
This object is to control a row creation of a CR PVPC. When RowStatus is createAndWait, information for a row is cached in memory; when RowStatus is set to createAndGo or active, it indicates that all information is to be written to permanent storage, and the PVPC to be enabled. When querying the object, 'active' indicates the PVPC is physically connected and data traffic can flow. The Rowstatus of 'notInService' indicates the PVPC is physically connected but data cannot flow. If the RowStatus value of 'notReady' is returned, it indicates either the PVPC is not physically connected (ie. configured only) or the SNMP agent is awaiting further information before setting up the connection. When deleting a connection, use this object with the value 'destroy'
OBJECT-TYPE    
  RowStatus  

nncCrPvccTable 1.3.6.1.4.1.123.3.79.1.2
nncCrPvccTable contains all the objects sent to a source endpoint that are used to create, modify, delete and query Cell Relay PVC connections.
OBJECT-TYPE    
  SEQUENCE OF  
    NncCrPvccTableEntry

nncCrPvccTableEntry 1.3.6.1.4.1.123.3.79.1.2.1
An entry of nncCrPvccTable. It contains the objects required to manage CR PVCs.
OBJECT-TYPE    
  NncCrPvccTableEntry  

nncCrPvccSrcIfIndex 1.3.6.1.4.1.123.3.79.1.2.1.1
This object contains the ifIndex value for the source endpoint.
OBJECT-TYPE    
  InterfaceIndex  

nncCrPvccSrcVpi 1.3.6.1.4.1.123.3.79.1.2.1.2
This object contains the VPI value for the source endpoint.
OBJECT-TYPE    
  INTEGER 0..4095  

nncCrPvccSrcVci 1.3.6.1.4.1.123.3.79.1.2.1.3
This object contains the VCI value for the source endpoint.
OBJECT-TYPE    
  INTEGER 0..65535  

nncCrPvccDstIfIndex 1.3.6.1.4.1.123.3.79.1.2.1.4
This object contains the ifIndex value for the destination endpoint.
OBJECT-TYPE    
  InterfaceIndex  

nncCrPvccDstVpi 1.3.6.1.4.1.123.3.79.1.2.1.5
This object contains the VPI value for the destination endpoint.
OBJECT-TYPE    
  INTEGER 0..4095  

nncCrPvccDstVci 1.3.6.1.4.1.123.3.79.1.2.1.6
This object contains the VCI value for the destination endpoint.
OBJECT-TYPE    
  INTEGER 0..65535  

nncCrPvccCastType 1.3.6.1.4.1.123.3.79.1.2.1.7
This object is used to indicate whether the PVCC is point-to-point or point-to-multipoint
OBJECT-TYPE    
  INTEGER p2p(1), p2mp(2)  

nncCrPvccFwdServiceCategory 1.3.6.1.4.1.123.3.79.1.2.1.8
This object is used to set the traffic service category from source endpoint to destination endpoint. This object is dependent on the value specified in nncCrPvccFwdTmTrafficDescripton object
OBJECT-TYPE    
  INTEGER cbr(1), nrtvbr(2), abr(3), ubr(4), rtvbr(6)  

nncCrPvccBwdServiceCategory 1.3.6.1.4.1.123.3.79.1.2.1.9
This object is used to set the traffic service category from destination end point to source endpoint. This object is dependent on the value specified in nncCrPvccBwdTmTrafficDescripton object
OBJECT-TYPE    
  INTEGER cbr(1), nrtvbr(2), abr(3), ubr(4), rtvbr(6)  

nncCrPvccFwdAbrDynTrfcIcr 1.3.6.1.4.1.123.3.79.1.2.1.10
ABR dynamic traffic descriptor's Initial Cell Rate for the forward direction. Range: 0 - 2488320 Kb/s
OBJECT-TYPE    
  INTEGER 0..2488320  

nncCrPvccFwdAbrDynTrfcRif 1.3.6.1.4.1.123.3.79.1.2.1.11
ABR traffic Rate Increase Factor for the forward direction. Value is expressed as the -power of 2. Range: 0 - 9
OBJECT-TYPE    
  INTEGER 0..9  

nncCrPvccFwdAbrDynTrfcRdf 1.3.6.1.4.1.123.3.79.1.2.1.12
ABR traffic Rate Decrease Factor descriptor for the forward direction. Value is expressed as the -power of 2 Range: 0 - 9
OBJECT-TYPE    
  INTEGER 0..9  

nncCrPvccBwdAbrDynTrfcIcr 1.3.6.1.4.1.123.3.79.1.2.1.13
ABR dynamic traffic descriptor's Initial Cell Rate for the destination endpoint. Range: 0 - 2488320 Kb/s
OBJECT-TYPE    
  INTEGER 0..2488320  

nncCrPvccBwdAbrDynTrfcRif 1.3.6.1.4.1.123.3.79.1.2.1.14
ABR traffic Rate Increase Factor for the destination endpoint. Value is expressed as the -power of 2. Range: 0 - 9
OBJECT-TYPE    
  INTEGER 0..9  

nncCrPvccBwdAbrDynTrfcRdf 1.3.6.1.4.1.123.3.79.1.2.1.15
ABR traffic Rate Decrease Factor descriptor for the destination endpoint. Value is expressed as the -power of 2 Range: 0 - 9
OBJECT-TYPE    
  INTEGER 0..9  

nncCrPvccSrcBillingFlag 1.3.6.1.4.1.123.3.79.1.2.1.16
Billing Configuration for the source endpoint.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

nncCrPvccDstBillingFlag 1.3.6.1.4.1.123.3.79.1.2.1.17
Billing Configuration for the destination endpoint.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

nncCrPvccFwdTmTrafficDescriptor 1.3.6.1.4.1.123.3.79.1.2.1.18
This object contains the traffic descriptor for the PVC. None (0) (Not applicable,the case of a P2MP leaf) Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0+1/S_0 (4) (NRT/RT-VBR only) P_0+1/M_0+1 (5) (ABR and UBR only)
OBJECT-TYPE    
  INTEGER none(0), tagAll(1), p0Plus1(2), p0Plus1SlashS0Plus1(3), p0Plus1SlashS0(4), p0Plus1SlashM0Plus1(5)  

nncCrPvccFwdTmPolicingOption 1.3.6.1.4.1.123.3.79.1.2.1.19
Policing Option for a PVcC. The tag option is supported only on rt-VBR/nrt-VBR connections that use the P_0_1/S_0 traffic descriptor
OBJECT-TYPE    
  INTEGER none(0), disabled(1), tag(2), discard(3)  

nncCrPvccFwdTmBucketOneRate 1.3.6.1.4.1.123.3.79.1.2.1.20
This object is used for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. Range: 0 - 2488320 Kb/s
OBJECT-TYPE    
  INTEGER 0..2488320  

nncCrPvccFwdTmBucketOneCdvt 1.3.6.1.4.1.123.3.79.1.2.1.21
This object is used to set cell delay variation tolerance (CDVT) for one end point, measured in microseconds. Range: 1 - 190,000 microseconds
OBJECT-TYPE    
  INTEGER 1..190000  

nncCrPvccFwdTmBucketTwoRate 1.3.6.1.4.1.123.3.79.1.2.1.22
SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range: 0 - 2488320 Kb/s
OBJECT-TYPE    
  INTEGER 0..2488320  

nncCrPvccFwdTmBucketTwoMbs 1.3.6.1.4.1.123.3.79.1.2.1.23
This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrt-VBR and rt-VBR only). Range: 1 - 10000 cells
OBJECT-TYPE    
  INTEGER 1..10000  

nncCrPvccFwdTmCdv 1.3.6.1.4.1.123.3.79.1.2.1.24
This value is to set the cell delay variation (CDV) between two PVC endpoints when using the rt-VBR service category. Range: 250-10000 microseconds
OBJECT-TYPE    
  INTEGER 250..10000  

nncCrPvccFwdTmClr 1.3.6.1.4.1.123.3.79.1.2.1.25
The object is to set the cell loss ratio (CLR) between two PVC endpoints when using the nrt-VBR service category. Value set as 1.0e-#
OBJECT-TYPE    
  INTEGER 1..7  

nncCrPvccFwdTmFrameDiscard 1.3.6.1.4.1.123.3.79.1.2.1.26
The Frame (AAL protocol data unit) Discard option. When enabled, cells are discarded at the frame level by examining the SDU-type in the payload type field of the ATM cell header.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

nncCrPvccBwdTmTrafficDescriptor 1.3.6.1.4.1.123.3.79.1.2.1.27
This object contains the traffic descriptor for the SPVC. None (0) (Not applicable,the case of a P2MP leaf) Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0+1/S_0 (4) (NRT/RT-VBR only) P_0+1/M_0+1 (5) (ABR and UBR only)
OBJECT-TYPE    
  INTEGER none(0), tagAll(1), p0Plus1(2), p0Plus1SlashS0Plus1(3), p0Plus1SlashS0(4), p0Plus1SlashM0Plus1(5)  

nncCrPvccBwdTmPolicingOption 1.3.6.1.4.1.123.3.79.1.2.1.28
Policing Option for an PVCC. The tag option is supported only on rt-VBR/nrt-VBR connections that use the P_0_1/S_0 traffic descriptor
OBJECT-TYPE    
  INTEGER none(0), disabled(1), tag(2), discard(3)  

nncCrPvccBwdTmBucketOneRate 1.3.6.1.4.1.123.3.79.1.2.1.29
This object is used for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. Range: 0 - 2488320 Kb/s
OBJECT-TYPE    
  INTEGER 0..2488320  

nncCrPvccBwdTmBucketOneCdvt 1.3.6.1.4.1.123.3.79.1.2.1.30
This object is used to set cell delay variation tolerance (CDVT) for one end point, measured in microseconds. Range: 1 - 190,000 microseconds
OBJECT-TYPE    
  INTEGER 1..190000  

nncCrPvccBwdTmBucketTwoRate 1.3.6.1.4.1.123.3.79.1.2.1.31
SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range: 0 - 2488320 Kb/s
OBJECT-TYPE    
  INTEGER 0..2488320  

nncCrPvccBwdTmBucketTwoMbs 1.3.6.1.4.1.123.3.79.1.2.1.32
This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrt-VBR and rt-VBR only). Range: 1 - 10000 cells
OBJECT-TYPE    
  INTEGER 1..10000  

nncCrPvccBwdTmCdv 1.3.6.1.4.1.123.3.79.1.2.1.33
This value is to set the cell delay variation (CDV) between two PVC endpoints when using the rt-VBR service category. Range: 250-10000 microseconds
OBJECT-TYPE    
  INTEGER 250..10000  

nncCrPvccBwdTmClr 1.3.6.1.4.1.123.3.79.1.2.1.34
The object is to set the cell loss ratio (CLR) between two PVC endpoints when using the nrt-VBR service category. Value set as 1.0e-# Range: 0 - 7
OBJECT-TYPE    
  INTEGER 1..7  

nncCrPvccBwdTmFrameDiscard 1.3.6.1.4.1.123.3.79.1.2.1.35
The Frame (AAL protocol data unit) Discard option. When enabled, cells are discarded at the frame level by examining the SDU-type in the payload type field of the ATM cell header.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

nncCrPvccSrcAlsConfig 1.3.6.1.4.1.123.3.79.1.2.1.36
This object is used to set OAM Alarm Surveillance configuration for the source endpoint.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

nncCrPvccDstAlsConfig 1.3.6.1.4.1.123.3.79.1.2.1.37
This object is used to set OAM Alarm Surveillance configuration for the destination endpoint.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

nncCrPvccCreator 1.3.6.1.4.1.123.3.79.1.2.1.38
The object retrieves the creator of a PVC connection.
OBJECT-TYPE    
  INTEGER unknown(0), nmti(1), nm5620(2), snmp(9)  

nncCrPvccRowStatus 1.3.6.1.4.1.123.3.79.1.2.1.39
This object is to control a row creation of a CR PVCC. When RowStatus is createAndWait, information for a row is cached in memory; when RowStatus is set to createAndGo or active, it indicates that all information is to be written to permanent storage, and the PVCC to be enabled. When querying the object, 'active' indicates the PVCC is physically connected and data traffic can flow. The Rowstatus of 'notInService' indicates the PVCC is physically connected but data cannot flow. If the RowStatus value of 'notReady' is returned, it indicates either the PVCC is not physically connected (ie. configured only) or the SNMP agent is awaiting further information before setting up the connection. When deleting a connection, use this object with the value 'destroy'
OBJECT-TYPE    
  RowStatus  

nncExtPvcGroups 1.3.6.1.4.1.123.3.79.3
OBJECT IDENTIFIER    

nncCrPvpcGroup 1.3.6.1.4.1.123.3.79.3.1
Common MIB objects for configuring a CR PVPC on Alcatel CID equipment
OBJECT-GROUP    

nncCrPvccGroup 1.3.6.1.4.1.123.3.79.3.2
Common MIB objects for configuring a CR PVCC on Alcatel CID equipment
OBJECT-GROUP    

nncExtPvcCompliances 1.3.6.1.4.1.123.3.79.4
OBJECT IDENTIFIER    

nncPvcCompliance 1.3.6.1.4.1.123.3.79.4.1
The compliance statement for Alcatel CID PVC MIB implementation.
MODULE-COMPLIANCE    

Defined Objects

NncCrPvpcTableEntry  
SEQUENCE    
  InterfaceIndex as nncCrPvpcSrcIfIndex  
  INTEGER as nncCrPvpcSrcVpi  
  InterfaceIndex as nncCrPvpcDstIfIndex  
  INTEGER as nncCrPvpcDstVpi  
  INTEGER as nncCrPvpcCastType  
  INTEGER as nncCrPvpcFwdServiceCategory  
  INTEGER as nncCrPvpcBwdServiceCategory  
  INTEGER as nncCrPvpcFwdAbrDynTrfcIcr  
  INTEGER as nncCrPvpcFwdAbrDynTrfcRif  
  INTEGER as nncCrPvpcFwdAbrDynTrfcRdf  
  INTEGER as nncCrPvpcBwdAbrDynTrfcIcr  
  INTEGER as nncCrPvpcBwdAbrDynTrfcRif  
  INTEGER as nncCrPvpcBwdAbrDynTrfcRdf  
  INTEGER as nncCrPvpcSrcBillingFlag  
  INTEGER as nncCrPvpcDstBillingFlag  
  INTEGER as nncCrPvpcFwdTmTrafficDescriptor  
  INTEGER as nncCrPvpcFwdTmPolicingOption  
  INTEGER as nncCrPvpcFwdTmBucketOneRate  
  INTEGER as nncCrPvpcFwdTmBucketOneCdvt  
  INTEGER as nncCrPvpcFwdTmBucketTwoRate  
  INTEGER as nncCrPvpcFwdTmBucketTwoMbs  
  INTEGER as nncCrPvpcFwdTmCdv  
  INTEGER as nncCrPvpcFwdTmClr  
  INTEGER as nncCrPvpcBwdTmTrafficDescriptor  
  INTEGER as nncCrPvpcBwdTmPolicingOption  
  INTEGER as nncCrPvpcBwdTmBucketOneRate  
  INTEGER as nncCrPvpcBwdTmBucketOneCdvt  
  INTEGER as nncCrPvpcBwdTmBucketTwoRate  
  INTEGER as nncCrPvpcBwdTmBucketTwoMbs  
  INTEGER as nncCrPvpcBwdTmCdv  
  INTEGER as nncCrPvpcBwdTmClr  
  INTEGER as nncCrPvpcSrcAlsConfig  
  INTEGER as nncCrPvpcDstAlsConfig  
  INTEGER as nncCrPvpcCreator  
  RowStatus as nncCrPvpcRowStatus  

NncCrPvccTableEntry  
SEQUENCE    
  InterfaceIndex as nncCrPvccSrcIfIndex  
  INTEGER as nncCrPvccSrcVpi  
  INTEGER as nncCrPvccSrcVci  
  InterfaceIndex as nncCrPvccDstIfIndex  
  INTEGER as nncCrPvccDstVpi  
  INTEGER as nncCrPvccDstVci  
  INTEGER as nncCrPvccCastType  
  INTEGER as nncCrPvccFwdServiceCategory  
  INTEGER as nncCrPvccBwdServiceCategory  
  INTEGER as nncCrPvccFwdAbrDynTrfcIcr  
  INTEGER as nncCrPvccFwdAbrDynTrfcRif  
  INTEGER as nncCrPvccFwdAbrDynTrfcRdf  
  INTEGER as nncCrPvccBwdAbrDynTrfcIcr  
  INTEGER as nncCrPvccBwdAbrDynTrfcRif  
  INTEGER as nncCrPvccBwdAbrDynTrfcRdf  
  INTEGER as nncCrPvccSrcBillingFlag  
  INTEGER as nncCrPvccDstBillingFlag  
  INTEGER as nncCrPvccFwdTmTrafficDescriptor  
  INTEGER as nncCrPvccFwdTmPolicingOption  
  INTEGER as nncCrPvccFwdTmBucketOneRate  
  INTEGER as nncCrPvccFwdTmBucketOneCdvt  
  INTEGER as nncCrPvccFwdTmBucketTwoRate  
  INTEGER as nncCrPvccFwdTmBucketTwoMbs  
  INTEGER as nncCrPvccFwdTmCdv  
  INTEGER as nncCrPvccFwdTmClr  
  INTEGER as nncCrPvccFwdTmFrameDiscard  
  INTEGER as nncCrPvccBwdTmTrafficDescriptor  
  INTEGER as nncCrPvccBwdTmPolicingOption  
  INTEGER as nncCrPvccBwdTmBucketOneRate  
  INTEGER as nncCrPvccBwdTmBucketOneCdvt  
  INTEGER as nncCrPvccBwdTmBucketTwoRate  
  INTEGER as nncCrPvccBwdTmBucketTwoMbs  
  INTEGER as nncCrPvccBwdTmCdv  
  INTEGER as nncCrPvccBwdTmClr  
  INTEGER as nncCrPvccBwdTmFrameDiscard  
  INTEGER as nncCrPvccSrcAlsConfig  
  INTEGER as nncCrPvccDstAlsConfig  
  INTEGER as nncCrPvccCreator  
  RowStatus as nncCrPvccRowStatus