Nortel-Magellan-Passport-GeneralVcInterfaceMIB

File: Nortel-Magellan-Passport-GeneralVcInterfaceMIB.mib (259665 bytes)

Imported modules

RFC-1212 Nortel-Magellan-Passport-UsefulDefinitionsMIB Nortel-Magellan-Passport-StandardTextualConventionsMIB
Nortel-Magellan-Passport-TextualConventionsMIB

Imported symbols

OBJECT-TYPE components passportMIBs
Counter32 RowPointer DisplayString
StorageType RowStatus InterfaceIndex
Gauge32 Integer32 Unsigned32
AsciiString DashedHexString NonReplicated
DigitString HexString EnterpriseDateAndTime
Hex Link

Defined Objects

gvcIf 1.3.6.1.4.1.562.2.4.1.107
OBJECT IDENTIFIER    

gvcIfRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.1
This entry controls the addition and deletion of gvcIf components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfRowStatusEntry

gvcIfRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.1.1
A single entry in the table represents a single gvcIf component.
OBJECT-TYPE    
  GvcIfRowStatusEntry  

gvcIfRowStatus 1.3.6.1.4.1.562.2.4.1.107.1.1.1
This variable is used as the basis for SNMP naming of gvcIf components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfComponentName 1.3.6.1.4.1.562.2.4.1.107.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfStorageType 1.3.6.1.4.1.562.2.4.1.107.1.1.4
This variable represents the storage type value for the gvcIf tables.
OBJECT-TYPE    
  StorageType  

gvcIfIndex 1.3.6.1.4.1.562.2.4.1.107.1.1.10
This variable represents the index for the gvcIf tables.
OBJECT-TYPE    
  Integer32 0..15  

gvcIfDc 1.3.6.1.4.1.562.2.4.1.107.2
OBJECT IDENTIFIER    

gvcIfDcRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.2.1
This entry controls the addition and deletion of gvcIfDc components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDcRowStatusEntry

gvcIfDcRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.2.1.1
A single entry in the table represents a single gvcIfDc component.
OBJECT-TYPE    
  GvcIfDcRowStatusEntry  

gvcIfDcRowStatus 1.3.6.1.4.1.562.2.4.1.107.2.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDc components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDcComponentName 1.3.6.1.4.1.562.2.4.1.107.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDcStorageType 1.3.6.1.4.1.562.2.4.1.107.2.1.1.4
This variable represents the storage type value for the gvcIfDc tables.
OBJECT-TYPE    
  StorageType  

gvcIfDcMacIndex 1.3.6.1.4.1.562.2.4.1.107.2.1.1.10
This variable represents an index for the gvcIfDc tables.
OBJECT-TYPE    
  DashedHexString SIZE(6)  

gvcIfDcSapIndex 1.3.6.1.4.1.562.2.4.1.107.2.1.1.11
This variable represents an index for the gvcIfDc tables.
OBJECT-TYPE    
  Integer32 2..254  

gvcIfDcOptionsTable 1.3.6.1.4.1.562.2.4.1.107.2.10
This group defines attributes associated with direct call. It defines complete connection in terms of path and call options. This connection can be permanent (pvc) or switched (svc). It can have facilities. The total number of bytes of facilities including the facility codes, and all of the facility data from all of the four classes of facilities: CCITT_Facilities DTE_Facilities National_Facilities International_Facilities must not exceed 512 bytes.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDcOptionsEntry

gvcIfDcOptionsEntry 1.3.6.1.4.1.562.2.4.1.107.2.10.1
An entry in the gvcIfDcOptionsTable.
OBJECT-TYPE    
  GvcIfDcOptionsEntry  

gvcIfDcRemoteNpi 1.3.6.1.4.1.562.2.4.1.107.2.10.1.3
This attribute specifies the remote Numbering Plan Indicator (Npi) used in the remoteDna.
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

gvcIfDcRemoteDna 1.3.6.1.4.1.562.2.4.1.107.2.10.1.4
This attribute specifies the Data Network Address (Dna) of the remote. This is the called (destination) DTE address (Dna) to which this direct call will be sent. Initially, the called DTE address attribute must be present, that is, there must be a valid destination address. However, it may be possible in the future to configure the direct call with a mnemonic address, in which case, this attribute will contain a zero-length Dna, and the mnemonic address will be carried as one of the facilities.
OBJECT-TYPE    
  DigitString SIZE(1..15)  

gvcIfDcUserData 1.3.6.1.4.1.562.2.4.1.107.2.10.1.8
This attribute contains the user data which is appended to the call request packet that is presented to the called (destination) DTE. User data can be a 0 to 128 byte string for fast select calls; otherwise, it is 0 to 16 byte string. Fast select calls are indicated as such using the X.25 ITU-T CCITT facility for 'Reverse Charging'. The length of the user data attribute is not verified during service provisioning. If more than 16 bytes of user data is specified on a call without the fast select option, then the call is cleared with a clear cause of 'local procedure error', and a diagnostic code of 39 (as defined in ITU-T (CCITT) X.25).
OBJECT-TYPE    
  HexString SIZE(0..128)  

gvcIfDcTransferPriority 1.3.6.1.4.1.562.2.4.1.107.2.10.1.9
This attribute specifies the default transfer priority to network for all outgoing calls using this particular Dna. It can overRide the outDefaultTransferPriority provisioned in the Dna component. The transfer priority is a preference specified by an application according to its time-sensitivity requirement. Frames with high transfer priority are served by the network before the frames with normal priority. The transfer priority in Passport determines two things in use: trunk queue (among interrupting, delay, throughput), and routing metric (between delay and throughput). The following table details each transfer priority. The default of outDefaultTransferPriority is useDnaDefTP.
OBJECT-TYPE    
  INTEGER normal(0), high(9), useDnaDefTP(255)  

gvcIfDcDiscardPriority 1.3.6.1.4.1.562.2.4.1.107.2.10.1.10
This attribute specifies the discard priority for outgoing call using this DLCI. The discard priority has three provisioning values: normal, high, and useDnaDefPriority. Traffic with normal priority are discarded first than the traffic with high priority. The Dna default value (provisioned by outDefaultPriority) is taken if this attribute is set to the value useDnaDefPriority. The default of discardPriority is useDnaDefPriority.
OBJECT-TYPE    
  INTEGER normal(0), high(1), useDnaDefPriority(3)  

gvcIfDcCfaTable 1.3.6.1.4.1.562.2.4.1.107.2.490
This is the i'th CCITT facility required for this direct call. Within the provisioning system, the user specifies the facility code along with the facility parameters. The facility is represented internally as a hexadecimal string following the X.25 CCITT representation for facility data. The user specifies the facility code when adding, changing or deleting a facility. The upper two bits of the facility code indicate the class of facility. From the class of the facility, one can derive the number of bytes of facility data, as follows: Class A - 1 byte of fax data Class B - 2 bytes of fax data Class C - 3 bytes of fax data Class D - variable length of fax data.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDcCfaEntry

gvcIfDcCfaEntry 1.3.6.1.4.1.562.2.4.1.107.2.490.1
An entry in the gvcIfDcCfaTable.
OBJECT-TYPE    
  GvcIfDcCfaEntry  

gvcIfDcCfaIndex 1.3.6.1.4.1.562.2.4.1.107.2.490.1.1
This variable represents the index for the gvcIfDcCfaTable.
OBJECT-TYPE    
  Integer32 1 | 2 | 3 | 4 | 9 | 66 | 67 | 68 | 71 | 72 | 73 | 196 | 198  

gvcIfDcCfaValue 1.3.6.1.4.1.562.2.4.1.107.2.490.1.2
This variable represents an individual value for the gvcIfDcCfaTable.
OBJECT-TYPE    
  HexString SIZE(0..128)  

gvcIfDcCfaRowStatus 1.3.6.1.4.1.562.2.4.1.107.2.490.1.3
This variable is used to control the addition and deletion of individual values of the gvcIfDcCfaTable.
OBJECT-TYPE    
  RowStatus  

gvcIfRDnaMap 1.3.6.1.4.1.562.2.4.1.107.3
OBJECT IDENTIFIER    

gvcIfRDnaMapRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.3.1
This entry controls the addition and deletion of gvcIfRDnaMap components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfRDnaMapRowStatusEntry

gvcIfRDnaMapRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.3.1.1
A single entry in the table represents a single gvcIfRDnaMap component.
OBJECT-TYPE    
  GvcIfRDnaMapRowStatusEntry  

gvcIfRDnaMapRowStatus 1.3.6.1.4.1.562.2.4.1.107.3.1.1.1
This variable is used as the basis for SNMP naming of gvcIfRDnaMap components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfRDnaMapComponentName 1.3.6.1.4.1.562.2.4.1.107.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfRDnaMapStorageType 1.3.6.1.4.1.562.2.4.1.107.3.1.1.4
This variable represents the storage type value for the gvcIfRDnaMap tables.
OBJECT-TYPE    
  StorageType  

gvcIfRDnaMapNpiIndex 1.3.6.1.4.1.562.2.4.1.107.3.1.1.10
This variable represents an index for the gvcIfRDnaMap tables.
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

gvcIfRDnaMapDnaIndex 1.3.6.1.4.1.562.2.4.1.107.3.1.1.11
This variable represents an index for the gvcIfRDnaMap tables.
OBJECT-TYPE    
  DigitString SIZE(1..15)  

gvcIfRDnaMapLanAdTable 1.3.6.1.4.1.562.2.4.1.107.3.10
This group defines the LAN MAC and SAP address for a given WAN NPI and DNA address.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfRDnaMapLanAdEntry

gvcIfRDnaMapLanAdEntry 1.3.6.1.4.1.562.2.4.1.107.3.10.1
An entry in the gvcIfRDnaMapLanAdTable.
OBJECT-TYPE    
  GvcIfRDnaMapLanAdEntry  

gvcIfRDnaMapMac 1.3.6.1.4.1.562.2.4.1.107.3.10.1.2
This attribute specifies a locally or globally administered MAC address of a LAN device.
OBJECT-TYPE    
  DashedHexString SIZE(6)  

gvcIfRDnaMapSap 1.3.6.1.4.1.562.2.4.1.107.3.10.1.3
This attribute specifies a SAP identifier on the LAN device identified by the mac.
OBJECT-TYPE    
  Hex 2..254  

gvcIfLcn 1.3.6.1.4.1.562.2.4.1.107.4
OBJECT IDENTIFIER    

gvcIfLcnRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.4.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of gvcIfLcn components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfLcnRowStatusEntry

gvcIfLcnRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.4.1.1
A single entry in the table represents a single gvcIfLcn component.
OBJECT-TYPE    
  GvcIfLcnRowStatusEntry  

gvcIfLcnRowStatus 1.3.6.1.4.1.562.2.4.1.107.4.1.1.1
This variable is used as the basis for SNMP naming of gvcIfLcn components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfLcnComponentName 1.3.6.1.4.1.562.2.4.1.107.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfLcnStorageType 1.3.6.1.4.1.562.2.4.1.107.4.1.1.4
This variable represents the storage type value for the gvcIfLcn tables.
OBJECT-TYPE    
  StorageType  

gvcIfLcnIndex 1.3.6.1.4.1.562.2.4.1.107.4.1.1.10
This variable represents the index for the gvcIfLcn tables.
OBJECT-TYPE    
  Integer32 1..4095  

gvcIfLcnVc 1.3.6.1.4.1.562.2.4.1.107.4.2
OBJECT IDENTIFIER    

gvcIfLcnVcRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.4.2.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of gvcIfLcnVc components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfLcnVcRowStatusEntry

gvcIfLcnVcRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.4.2.1.1
A single entry in the table represents a single gvcIfLcnVc component.
OBJECT-TYPE    
  GvcIfLcnVcRowStatusEntry  

gvcIfLcnVcRowStatus 1.3.6.1.4.1.562.2.4.1.107.4.2.1.1.1
This variable is used as the basis for SNMP naming of gvcIfLcnVc components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfLcnVcComponentName 1.3.6.1.4.1.562.2.4.1.107.4.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfLcnVcStorageType 1.3.6.1.4.1.562.2.4.1.107.4.2.1.1.4
This variable represents the storage type value for the gvcIfLcnVc tables.
OBJECT-TYPE    
  StorageType  

gvcIfLcnVcIndex 1.3.6.1.4.1.562.2.4.1.107.4.2.1.1.10
This variable represents the index for the gvcIfLcnVc tables.
OBJECT-TYPE    
  NonReplicated  

gvcIfLcnVcCadTable 1.3.6.1.4.1.562.2.4.1.107.4.2.10
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group represents operational call data related to General Vc. It can be displayed only for General Vc which is created by application.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfLcnVcCadEntry

gvcIfLcnVcCadEntry 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1
An entry in the gvcIfLcnVcCadTable.
OBJECT-TYPE    
  GvcIfLcnVcCadEntry  

gvcIfLcnVcType 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.1
This attribute displays the type of call, pvc or svc. type is provided at provisioning time.
OBJECT-TYPE    
  INTEGER svc(0), pvc(1)  

gvcIfLcnVcState 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.2
This attribute displays the state of call control. P5 state is not supported but is listed for completness. Transitions from one state to another take very short time. state most often displayed is dataTransferP4.
OBJECT-TYPE    
  INTEGER creating(0), readyP1(1), dteWaitingP2(2), dceWaitingP3(3), dataTransferP4(4), unsupportedP5(5), dteClearRequestP6(6), dceClearIndicationP7(7), termination(8)  

gvcIfLcnVcPreviousState 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.3
This attribute displays the previous state of call control. This is a valuable field to determine how the processing is progressing.
OBJECT-TYPE    
  INTEGER creating(0), readyP1(1), dteWaitingP2(2), dceWaitingP3(3), dataTransferP4(4), unsupportedP5(5), dteClearRequestP6(6), dceClearIndicationP7(7), termination(8)  

gvcIfLcnVcDiagnosticCode 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.4
This attribute displays the internal substate of call control. It is used to further refine state of call processing.
OBJECT-TYPE    
  Unsigned32 0..255  

gvcIfLcnVcPreviousDiagnosticCode 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.5
This attribute displays the internal substate of call control. It is used to further refine state of call processing.
OBJECT-TYPE    
  Unsigned32 0..255  

gvcIfLcnVcCalledNpi 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.6
This attribute displays the Numbering Plan Indicator (NPI) of the called end.
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

gvcIfLcnVcCalledDna 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.7
This attribute displays the Data Network Address (Dna) of the called (destination) DTE to which this call is sent. This address if defined at recieving end will complete Vc connection.
OBJECT-TYPE    
  DigitString SIZE(1..15)  

gvcIfLcnVcCalledLcn 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.8
This attribute displays the Logical Channel Number of the called end. It is valid only after both ends of Vc exchanged relevant information.
OBJECT-TYPE    
  Unsigned32 1..65535  

gvcIfLcnVcCallingNpi 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.9
This attribute displays the Numbering Plan Indicator (NPI) of the calling end.
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

gvcIfLcnVcCallingDna 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.10
This attribute displays the Data Network Address (Dna) of the calling end.
OBJECT-TYPE    
  DigitString SIZE(1..15)  

gvcIfLcnVcCallingLcn 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.11
This attribute displays the Logical Channel Number of the calling end.
OBJECT-TYPE    
  Unsigned32 1..65535  

gvcIfLcnVcAccountingEnabled 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.12
This attribute indicates that this optional section of accounting record is suppressed or permitted. If accountingEnabled is yes, conditions for generation of accounting record were met. These conditions include billing options, vc recovery conditions and Module wide accounting data options.
OBJECT-TYPE    
  INTEGER yes(0), no(1)  

gvcIfLcnVcFastSelectCall 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.13
This attribute displays that this is a fast select call.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

gvcIfLcnVcLocalRxPktSize 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.14
This attribute displays the locally negotiated size of send packets.
OBJECT-TYPE    
  INTEGER unknown(0), n16(4), n32(5), n64(6), n128(7), n256(8), n512(9), n1024(10), n2048(11), n4096(12)  

gvcIfLcnVcLocalTxPktSize 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.15
This attribute displays the locally negotiated size of send packets.
OBJECT-TYPE    
  INTEGER unknown(0), n16(4), n32(5), n64(6), n128(7), n256(8), n512(9), n1024(10), n2048(11), n4096(12)  

gvcIfLcnVcLocalTxWindowSize 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.16
This attribute displays the send window size provided on incoming call packets or the default when a call request packet does not explicitly provide the window size.
OBJECT-TYPE    
  Unsigned32 0..127  

gvcIfLcnVcLocalRxWindowSize 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.17
This attribute displays the receive window size provided on incoming call packets or the default when a call request does not explicitly provide the window sizes.
OBJECT-TYPE    
  Unsigned32 0..127  

gvcIfLcnVcPathReliability 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.19
This attribute displays the path reliability.
OBJECT-TYPE    
  INTEGER high(0), normal(1)  

gvcIfLcnVcAccountingEnd 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.20
This attribute indicates if this end should generate an accounting record. Normally, callingEnd is the end to generate an accounting record.
OBJECT-TYPE    
  INTEGER callingEnd(0), calledEnd(1)  

gvcIfLcnVcPriority 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.21
This attribute displays whether the call is a normal or a high priority call.
OBJECT-TYPE    
  INTEGER normal(0), high(1)  

gvcIfLcnVcSegmentSize 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.22
This attribute displays the segment size (in bytes) used on the call. It is used to calculate the number of segments transmitted and received.
OBJECT-TYPE    
  Unsigned32 0..4096  

gvcIfLcnVcSubnetTxPktSize 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.23
This attribute displays the locally negotiated size of the data packets on this Vc.
OBJECT-TYPE    
  INTEGER unknown(0), n16(4), n32(5), n64(6), n128(7), n256(8), n512(9), n1024(10), n2048(11), n4096(12)  

gvcIfLcnVcSubnetTxWindowSize 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.24
This attribute displays the current send window size of Vc.
OBJECT-TYPE    
  Unsigned32 0..4096  

gvcIfLcnVcSubnetRxPktSize 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.25
This attribute displays the locally negotiated size of receive packets.
OBJECT-TYPE    
  INTEGER unknown(0), n16(4), n32(5), n64(6), n128(7), n256(8), n512(9), n1024(10), n2048(11), n4096(12)  

gvcIfLcnVcSubnetRxWindowSize 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.26
This attribute displays the receive window size provided on incoming call packets and to the default when a call request does not explicitly provide the window sizes.
OBJECT-TYPE    
  Unsigned32 0..4096  

gvcIfLcnVcMaxSubnetPktSize 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.27
This attribute displays the maximum packet size allowed on Vc.
OBJECT-TYPE    
  Unsigned32 0..4096  

gvcIfLcnVcTransferPriorityToNetwork 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.28
This attribute displays the priority in which data is transferred to the network. The transfer priority is a preference specified by an application according to its delay-sensitivity requirement. Frames with high transfer priority are served by the network before the frames with normal priority. Each transfer priority contains a predetermined setting for trunk queue (interrupting, delay or throughput), and routing metric (delay or throughput). When the transfer priority is set at high, the trunk queue is set to high, the routing metric is set to delay. When the transfer priority is set at normal, the trunk queue is set to normal, the routing metric is set to throughput.
OBJECT-TYPE    
  INTEGER normal(0), high(9)  

gvcIfLcnVcTransferPriorityFromNetwork 1.3.6.1.4.1.562.2.4.1.107.4.2.10.1.29
This attribute displays the priority in which data is transferred from the network. The transfer priority is a preference specified by an application according to its delay-sensitivity requirement. Frames with high transfer priority are served by the network before the frames with normal priority. Each transfer priority contains a predetermined setting for trunk queue (interrupting, delay or throughput), and routing metric (delay or throughput). When the transfer priority is set at high, and the trunk queue is set to high, the routing metric is set to delay. When the transfer priority is set at normal, the trunk queue is set to normal, and the routing metric is set to throughput.
OBJECT-TYPE    
  INTEGER normal(0), high(9)  

gvcIfLcnVcIntdTable 1.3.6.1.4.1.562.2.4.1.107.4.2.11
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group defines display of interval data collected by Vc. Data in this group is variable and may depend on time when this display command is issued.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfLcnVcIntdEntry

gvcIfLcnVcIntdEntry 1.3.6.1.4.1.562.2.4.1.107.4.2.11.1
An entry in the gvcIfLcnVcIntdTable.
OBJECT-TYPE    
  GvcIfLcnVcIntdEntry  

gvcIfLcnVcCallReferenceNumber 1.3.6.1.4.1.562.2.4.1.107.4.2.11.1.1
This attribute displays the call reference number which is a unique number generated by the switch.The same Call Reference Number is stored in the interval data (accounting record) at both ends of the call. It can be used as one of the attributes in matching duplicate records generated at each end of the call.
OBJECT-TYPE    
  Hex 0..16777215  

gvcIfLcnVcElapsedTimeTillNow 1.3.6.1.4.1.562.2.4.1.107.4.2.11.1.2
This attribute displays the elapsed time representing the period of this interval data. It is elapsed time in 0.1 second increments since Vc started.
OBJECT-TYPE    
  Unsigned32 0..16777215  

gvcIfLcnVcSegmentsRx 1.3.6.1.4.1.562.2.4.1.107.4.2.11.1.3
This attribute displays the number of segments received at the time command was issued. This is the segment received count maintained by accounting at each end of the Vc. This counter is updated only when the packet cannot be successfully delivered out of the sink Vc and to the sink AP Conditions in which packets may be discarded by the sink Vc include: missing packets due to subnet discards, segmentation protocol violations due to subnet discard, duplicated and out-of-ranged packets and packets that arrive while Vc is in path recovery state.
OBJECT-TYPE    
  Unsigned32 0..16777215  

gvcIfLcnVcSegmentsSent 1.3.6.1.4.1.562.2.4.1.107.4.2.11.1.4
This attribute displays the number of segments sent at the time command was issued. This is the segment sent count maintained by accounting at the source Vc. Vc only counts packets that Vc thinks can be delivered successfully into the subnet. In reality, these packets may be dropped by trunking, for instance. This counter is not updated when splitting fails, when Vc is in a path recovery state, when packet forwarding fails to forward this packet and when subsequent packets have to be discarded as we want to minimize the chance of out-of-sequence and do not intentionally send out-of- sequenced packets into the subnet.
OBJECT-TYPE    
  Unsigned32 0..16777215  

gvcIfLcnVcStartTime 1.3.6.1.4.1.562.2.4.1.107.4.2.11.1.5
This attribute displays the start time of this interval period. If Vc spans 12 hour time or time of day change startTime reflects new time as recorded at 12 hour periods or time of day changes.
OBJECT-TYPE    
  EnterpriseDateAndTime SIZE(0 | 19)  

gvcIfLcnVcStatsTable 1.3.6.1.4.1.562.2.4.1.107.4.2.12
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** ... Statistics(Stats) This group defines general attributes collected by general Vc. The purpose of Vc attributes is to aid end users and verification people to understand the Vc internal behavior. This is particularly useful when the network has experienced abnormality and we want to isolate problems and pinpoint trouble spots. Attributes are collected on a per Vc basis. Until a need is identified, statistics are not collected at a processor level. Each attribute is stored in a 32 bit field and is initialized to zero when a Vc enters into the data transfer state. When a PVC is disconnected and then connected again, the attributes will be reset. Attributes cannot be reset through other methods.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfLcnVcStatsEntry

gvcIfLcnVcStatsEntry 1.3.6.1.4.1.562.2.4.1.107.4.2.12.1
An entry in the gvcIfLcnVcStatsTable.
OBJECT-TYPE    
  GvcIfLcnVcStatsEntry  

gvcIfLcnVcAckStackingTimeouts 1.3.6.1.4.1.562.2.4.1.107.4.2.12.1.1
This attribute counts the number of ack stacking timer expiries. It is used as an indicator of the acknowledgment behavior across the subnet when ack stacking is in effect. If it expires often, usually this means end users will experience longer delay. The ack stacking timer specifies how long the Vc will wait before finally sending the subnet acknowledgment. if this attribute is set to a value of 0, then the Vc will automatically return acknowledgment packets without delay. If this attribute is set to a value other than zero, then the Vc will wait for this amount of time in an attempt to piggyback the acknowledgment packet on another credit or data packet. If the Vc cannot piggyback the acknowledgment packet within this time, then the packet is returned without piggybacking.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfLcnVcOutOfRangeFrmFromSubnet 1.3.6.1.4.1.562.2.4.1.107.4.2.12.1.2
This attribute counts the number of subnet frames discarded due to the sequence number being out of range. Two Categories apply for the General Vc 1) lost Acks (previous Range) 2) unexpected Packets (next Range) Vc internally maintains its own sequence number of packet order and sequencing. Due to packet retransmission, Vc may receive duplicate packets that have the same Vc internal sequence number. Only 1 copy is accepted by the Vc and other copies of the same packets are detected through this count. This attribute can be used to record the frequency of packet retransmission due to Vc and other part of the subnet.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfLcnVcDuplicatesFromSubnet 1.3.6.1.4.1.562.2.4.1.107.4.2.12.1.3
This attribute counts the number of subnet packets discarded due to duplication. It is used to detect software error fault or duplication caused by retransmitting.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfLcnVcFrmRetryTimeouts 1.3.6.1.4.1.562.2.4.1.107.4.2.12.1.4
This attribute counts the number of frames which have retransmission time-out. If packets from Vc into the subnet are discarded by the subnet, the source Vc will not receive any acknowledgment. The retransmission timer then expires and packets will be retransmitted again. Note that the Vc idle probe may be retransmitted and is included in this count. This statistics does not show the distribution of how many times packets are retransmitted (e.g. first retransmission results in successful packet forwarding).
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfLcnVcPeakRetryQueueSize 1.3.6.1.4.1.562.2.4.1.107.4.2.12.1.5
This attribute indicates the peak size of the retransmission queue. This attribute is used as an indicator of the acknowledgment behavior across the subnet. It records the largest body of unacknowledged packets.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfLcnVcPeakOoSeqQueueSize 1.3.6.1.4.1.562.2.4.1.107.4.2.12.1.6
This attribute indicates the peak size of the out of sequence queue. This attribute is used as an indicator of the sequencing behavior across the subnet. It records the largest body of out of sequence packets.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfLcnVcPeakOoSeqFrmForwarded 1.3.6.1.4.1.562.2.4.1.107.4.2.12.1.7
This attribute indicates the peak size of the sequence packet queue. This attribute is used as an indicator of the sequencing behavior across the subnet. It records the largest body of out of sequence packets, which by the receipt of an expected packet have been transformed to expected packets. The number of times this peak is reached is not recorded as it is traffic dependent.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfLcnVcPeakStackedAcksRx 1.3.6.1.4.1.562.2.4.1.107.4.2.12.1.8
This attribute indicates the peak size of wait acks. This attribute is used as an indicator of the acknowledgment behavior across the subnet. It records the largest collective acknowledgment.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfLcnVcSubnetRecoveries 1.3.6.1.4.1.562.2.4.1.107.4.2.12.1.9
This attribute counts the number of successful Vc recovery attempts. This attribute is used as an indicator of how many times the Vc path is broken but can be recovered. This attribute is useful to record the number of network path failures.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfLcnVcWindowClosuresToSubnet 1.3.6.1.4.1.562.2.4.1.107.4.2.12.1.10
This attribute counts the number of window closures to subnet. A packet may have been sent into the subnet but its acknowledgment from the remote Vc has not yet been received. This is a 8 bit sequence number.This number is useful in detecting whether the Vc is sending any packet into the subnet.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfLcnVcWindowClosuresFromSubnet 1.3.6.1.4.1.562.2.4.1.107.4.2.12.1.11
This attribute counts the number of window closures from subnet. This attribute is useful in detecting whether the Vc is receiving any packet from the subnet.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfLcnVcWrTriggers 1.3.6.1.4.1.562.2.4.1.107.4.2.12.1.12
This attribute displays the number of times the Vc stays within the W-R region. The W-R region is a value used to determined the timing of credit transmission. Should the current window size be beneath this value, the credits will be transmitted immediately. Otherwise, they will be transmitted later with actual data. The wrTriggers statistic is therefore used to analyze the flow control and credit mechanism.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfLcnStateTable 1.3.6.1.4.1.562.2.4.1.107.4.11
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfLcnStateEntry

gvcIfLcnStateEntry 1.3.6.1.4.1.562.2.4.1.107.4.11.1
An entry in the gvcIfLcnStateTable.
OBJECT-TYPE    
  GvcIfLcnStateEntry  

gvcIfLcnAdminState 1.3.6.1.4.1.562.2.4.1.107.4.11.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

gvcIfLcnOperationalState 1.3.6.1.4.1.562.2.4.1.107.4.11.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

gvcIfLcnUsageState 1.3.6.1.4.1.562.2.4.1.107.4.11.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

gvcIfLcnLcnCIdTable 1.3.6.1.4.1.562.2.4.1.107.4.12
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group indicates the information about the LAN circuit.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfLcnLcnCIdEntry

gvcIfLcnLcnCIdEntry 1.3.6.1.4.1.562.2.4.1.107.4.12.1
An entry in the gvcIfLcnLcnCIdTable.
OBJECT-TYPE    
  GvcIfLcnLcnCIdEntry  

gvcIfLcnCircuitId 1.3.6.1.4.1.562.2.4.1.107.4.12.1.1
This attribute indicates the component name of the Vr/n Sna SnaCircuitEntry which represents this connection in the SNA DLR service. This component contains operational data about the LAN circuit.
OBJECT-TYPE    
  RowPointer  

gvcIfLcnOperTable 1.3.6.1.4.1.562.2.4.1.107.4.13
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains the operational Lcn attributes.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfLcnOperEntry

gvcIfLcnOperEntry 1.3.6.1.4.1.562.2.4.1.107.4.13.1
An entry in the gvcIfLcnOperTable.
OBJECT-TYPE    
  GvcIfLcnOperEntry  

gvcIfLcnState 1.3.6.1.4.1.562.2.4.1.107.4.13.1.1
This attribute indicates the logical channel internal state.
OBJECT-TYPE    
  INTEGER idle(0), localDeviceCalling(1), remoteDeviceCalling(2), callUp(3), serviceInitiatedClear(4), localDeviceClearing(5), remoteDeviceClearing(6), terminating(7), deviceMonitoring(8), deviceMonitoringSuspended(9)  

gvcIfLcnDnaMap 1.3.6.1.4.1.562.2.4.1.107.4.13.1.2
This attribute indicates the component name of the Ddm, Sdm or Ldev which contains the MAC address of the device being monitored by this Lcn.
OBJECT-TYPE    
  RowPointer  

gvcIfLcnSourceMac 1.3.6.1.4.1.562.2.4.1.107.4.13.1.3
This attribute indicates the source MAC address inserted by this LCN in the SA field of the 802.5 frames sent to the local ring.
OBJECT-TYPE    
  DashedHexString SIZE(6)  

gvcIfDna 1.3.6.1.4.1.562.2.4.1.107.5
OBJECT IDENTIFIER    

gvcIfDnaRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.5.1
This entry controls the addition and deletion of gvcIfDna components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaRowStatusEntry

gvcIfDnaRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.5.1.1
A single entry in the table represents a single gvcIfDna component.
OBJECT-TYPE    
  GvcIfDnaRowStatusEntry  

gvcIfDnaRowStatus 1.3.6.1.4.1.562.2.4.1.107.5.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDna components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDnaComponentName 1.3.6.1.4.1.562.2.4.1.107.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDnaStorageType 1.3.6.1.4.1.562.2.4.1.107.5.1.1.4
This variable represents the storage type value for the gvcIfDna tables.
OBJECT-TYPE    
  StorageType  

gvcIfDnaIndex 1.3.6.1.4.1.562.2.4.1.107.5.1.1.10
This variable represents the index for the gvcIfDna tables.
OBJECT-TYPE    
  Integer32 0..99  

gvcIfDnaCug 1.3.6.1.4.1.562.2.4.1.107.5.2
OBJECT IDENTIFIER    

gvcIfDnaCugRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.5.2.1
This entry controls the addition and deletion of gvcIfDnaCug components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaCugRowStatusEntry

gvcIfDnaCugRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.5.2.1.1
A single entry in the table represents a single gvcIfDnaCug component.
OBJECT-TYPE    
  GvcIfDnaCugRowStatusEntry  

gvcIfDnaCugRowStatus 1.3.6.1.4.1.562.2.4.1.107.5.2.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDnaCug components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDnaCugComponentName 1.3.6.1.4.1.562.2.4.1.107.5.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDnaCugStorageType 1.3.6.1.4.1.562.2.4.1.107.5.2.1.1.4
This variable represents the storage type value for the gvcIfDnaCug tables.
OBJECT-TYPE    
  StorageType  

gvcIfDnaCugIndex 1.3.6.1.4.1.562.2.4.1.107.5.2.1.1.10
This variable represents the index for the gvcIfDnaCug tables.
OBJECT-TYPE    
  Integer32 1..255  

gvcIfDnaCugCugOptionsTable 1.3.6.1.4.1.562.2.4.1.107.5.2.10
Attributes in this group defines ClosedUserGroup options associated with interlockCode. Dnas with the same Cug (interlockCode) make calls within this group. Various combinations which permit or prevent calls in the same Cug group are defined here.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaCugCugOptionsEntry

gvcIfDnaCugCugOptionsEntry 1.3.6.1.4.1.562.2.4.1.107.5.2.10.1
An entry in the gvcIfDnaCugCugOptionsTable.
OBJECT-TYPE    
  GvcIfDnaCugCugOptionsEntry  

gvcIfDnaCugType 1.3.6.1.4.1.562.2.4.1.107.5.2.10.1.1
This attribute specifies the Cug type - the Cug is either a national Cug, or an international Cug. International closed user groups are usually established between DTEs for which there is an X.75 Gateway between; whereas national closed user groups are usually established between DTEs for which there is no X.75 Gateway between. (National Cugs cannot normally traverse an X.75 Gateway). If this attribute is set to national, then the Cug is a national Cug, in which case, the dnic should be left at its default value since it is not part of a national Cug. If this attribute is set to international, then the Cug is an international Cug, in which case, the dnic should be set appropriately as part of the Cug interlockCode.
OBJECT-TYPE    
  INTEGER national(0), international(1)  

gvcIfDnaCugDnic 1.3.6.1.4.1.562.2.4.1.107.5.2.10.1.2
This attribute specifies the dnic (Data Network ID Code) the Cug by which packet networks are identified. This attribute is not applicable if the Cug is a national Cug, as specified by the Cug type attribute. There are usually 1 or 2 dnics assigned per country, for public networks. The U.S. is an exception where each BOC has a dnic. Also, a group of private networks can have its own dnic. dnic value is not an arbitrary number. It is assigned by international agreement and controlled by CCITT.
OBJECT-TYPE    
  DigitString SIZE(4)  

gvcIfDnaCugInterlockCode 1.3.6.1.4.1.562.2.4.1.107.5.2.10.1.3
This attribute specifies the Cug identifier of a national or international Cug call. It is an arbitrary number and it also can be called Cug in some descriptions. Interfaces (Dnas) with this number can make calls to Dnas with the same interlockCode.
OBJECT-TYPE    
  Unsigned32 0..65535  

gvcIfDnaCugPreferential 1.3.6.1.4.1.562.2.4.1.107.5.2.10.1.4
This attribute, if set to yes indicates that this Cug is the preferential Cug, in which case it will be used during the call establishment phase if the DTE has not explicitly specified a Cug index in the call request packet. If set to no, then this Cug is not the preferential Cug. Only one of the Cugs associated with a particular Dna can be the preferential Cug - only one Cug can have this attribute set to yes.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

gvcIfDnaCugOutCalls 1.3.6.1.4.1.562.2.4.1.107.5.2.10.1.5
This attribute, if set to allowed indicates that outgoing calls (from the DTE into the network) be made using this particular Cug. If set to a value of disallowed, then outgoing calls cannot be made using this Cug - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Outgoing Calls Barred' feature for Cugs in that outgoing calls are barred if this attribute is set to a value of disallowed.
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

gvcIfDnaCugIncCalls 1.3.6.1.4.1.562.2.4.1.107.5.2.10.1.6
This attribute, if set to allowed indicates that incoming calls (from the network to the DTE) be made using this particular Cug. If set to disallowed, then incoming calls cannot be made using this Cug - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Incoming Calls Barred' feature for Cugs in that incoming calls are barred if this attribute is set to a value of disallowed.
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

gvcIfDnaCugPrivileged 1.3.6.1.4.1.562.2.4.1.107.5.2.10.1.7
This attribute, if set to yes indicates that this Cug is a privileged Cug. In DPN, at least one side of a call setup within a Cug must have the Cug as a privileged Cug. If set to no, then the Cug is not privileged. If both the local DTE and the remote DTE subscribe to the Cug, but it is not privileged, then the call will be cleared. This attribute is typically used for a host DTE which must accept calls from many other DTEs in which case the other DTEs cannot call one another, but can call the host. In this example, the host would have the privileged Cug, and the other DTEs would belong to the same Cug, but it would not be privileged.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

gvcIfDnaHgM 1.3.6.1.4.1.562.2.4.1.107.5.3
OBJECT IDENTIFIER    

gvcIfDnaHgMRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.5.3.1
This entry controls the addition and deletion of gvcIfDnaHgM components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaHgMRowStatusEntry

gvcIfDnaHgMRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.5.3.1.1
A single entry in the table represents a single gvcIfDnaHgM component.
OBJECT-TYPE    
  GvcIfDnaHgMRowStatusEntry  

gvcIfDnaHgMRowStatus 1.3.6.1.4.1.562.2.4.1.107.5.3.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDnaHgM components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDnaHgMComponentName 1.3.6.1.4.1.562.2.4.1.107.5.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDnaHgMStorageType 1.3.6.1.4.1.562.2.4.1.107.5.3.1.1.4
This variable represents the storage type value for the gvcIfDnaHgM tables.
OBJECT-TYPE    
  StorageType  

gvcIfDnaHgMIndex 1.3.6.1.4.1.562.2.4.1.107.5.3.1.1.10
This variable represents the index for the gvcIfDnaHgM tables.
OBJECT-TYPE    
  NonReplicated  

gvcIfDnaHgMHgAddr 1.3.6.1.4.1.562.2.4.1.107.5.3.2
OBJECT IDENTIFIER    

gvcIfDnaHgMHgAddrRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.5.3.2.1
This entry controls the addition and deletion of gvcIfDnaHgMHgAddr components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaHgMHgAddrRowStatusEntry

gvcIfDnaHgMHgAddrRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.5.3.2.1.1
A single entry in the table represents a single gvcIfDnaHgMHgAddr component.
OBJECT-TYPE    
  GvcIfDnaHgMHgAddrRowStatusEntry  

gvcIfDnaHgMHgAddrRowStatus 1.3.6.1.4.1.562.2.4.1.107.5.3.2.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDnaHgMHgAddr components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDnaHgMHgAddrComponentName 1.3.6.1.4.1.562.2.4.1.107.5.3.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDnaHgMHgAddrStorageType 1.3.6.1.4.1.562.2.4.1.107.5.3.2.1.1.4
This variable represents the storage type value for the gvcIfDnaHgMHgAddr tables.
OBJECT-TYPE    
  StorageType  

gvcIfDnaHgMHgAddrIndex 1.3.6.1.4.1.562.2.4.1.107.5.3.2.1.1.10
This variable represents the index for the gvcIfDnaHgMHgAddr tables.
OBJECT-TYPE    
  Integer32 0..1  

gvcIfDnaHgMHgAddrAddrTable 1.3.6.1.4.1.562.2.4.1.107.5.3.2.10
This group contains attributes common to all DNAs. Every DNA used in the network is defined with this group of 2 attributes. String of address digits complemented by the NPI.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaHgMHgAddrAddrEntry

gvcIfDnaHgMHgAddrAddrEntry 1.3.6.1.4.1.562.2.4.1.107.5.3.2.10.1
An entry in the gvcIfDnaHgMHgAddrAddrTable.
OBJECT-TYPE    
  GvcIfDnaHgMHgAddrAddrEntry  

gvcIfDnaHgMHgAddrNumberingPlanIndicator 1.3.6.1.4.1.562.2.4.1.107.5.3.2.10.1.1
This attribute indicates the Numbering Plan Indicator (NPI) the Dna that is entered. Address may belong to X.121 or E.164 plans.
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

gvcIfDnaHgMHgAddrDataNetworkAddress 1.3.6.1.4.1.562.2.4.1.107.5.3.2.10.1.2
This attribute contains digits which form unique identifier of the customer interface. It can be compared (approximation only) telephone number where phone number identifies unique telephone set. Dna digits are selected and assigned by network operators.
OBJECT-TYPE    
  DigitString SIZE(1..15)  

gvcIfDnaHgMIfTable 1.3.6.1.4.1.562.2.4.1.107.5.3.10
This group contains the interface parameters between the HuntGroupMember and the Hunt Group server.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaHgMIfEntry

gvcIfDnaHgMIfEntry 1.3.6.1.4.1.562.2.4.1.107.5.3.10.1
An entry in the gvcIfDnaHgMIfTable.
OBJECT-TYPE    
  GvcIfDnaHgMIfEntry  

gvcIfDnaHgMAvailabilityUpdateThreshold 1.3.6.1.4.1.562.2.4.1.107.5.3.10.1.1
This attribute indicates the number of channels that have to be freed or occupied before the Availability Message Packet (AMP) is sent to the Hunt Group Server informing it of the status of this interface.
OBJECT-TYPE    
  Unsigned32 0..4096  

gvcIfDnaHgMOpTable 1.3.6.1.4.1.562.2.4.1.107.5.3.11
This group contains the operational attributes of the HuntGroupMember component.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaHgMOpEntry

gvcIfDnaHgMOpEntry 1.3.6.1.4.1.562.2.4.1.107.5.3.11.1
An entry in the gvcIfDnaHgMOpTable.
OBJECT-TYPE    
  GvcIfDnaHgMOpEntry  

gvcIfDnaHgMAvailabilityDelta 1.3.6.1.4.1.562.2.4.1.107.5.3.11.1.3
This attribute indicates the net change in the available link station connections since the last Availability Message Packet (AMP) was sent to the Hunt Group. Once the absolute value of this attribute reaches the availabilityUpdateThreshold an AMP is sent to the host and the availabilityDelta is reset to 0. If this attribute is positive it means an increase of the number of available link station connections. If it is negative it means a decrease in the number of available link station connections.
OBJECT-TYPE    
  INTEGER -4096..4096  

gvcIfDnaHgMMaxAvailableLinkStations 1.3.6.1.4.1.562.2.4.1.107.5.3.11.1.4
This attribute indicates the maximum number of available link station connections that can be established by this HuntGroupMember.
OBJECT-TYPE    
  Unsigned32 0..4096  

gvcIfDnaHgMAvailableLinkStations 1.3.6.1.4.1.562.2.4.1.107.5.3.11.1.6
This attribute indicates the number of available link station connections reported to the hunt group in the Availability Message Packet (AMP). It is incremented by the application when a link station connection is freed and decremented when a link station connection is occupied.
OBJECT-TYPE    
  Unsigned32 0..4096  

gvcIfDnaDdm 1.3.6.1.4.1.562.2.4.1.107.5.4
OBJECT IDENTIFIER    

gvcIfDnaDdmRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.5.4.1
This entry controls the addition and deletion of gvcIfDnaDdm components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaDdmRowStatusEntry

gvcIfDnaDdmRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.5.4.1.1
A single entry in the table represents a single gvcIfDnaDdm component.
OBJECT-TYPE    
  GvcIfDnaDdmRowStatusEntry  

gvcIfDnaDdmRowStatus 1.3.6.1.4.1.562.2.4.1.107.5.4.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDnaDdm components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDnaDdmComponentName 1.3.6.1.4.1.562.2.4.1.107.5.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDnaDdmStorageType 1.3.6.1.4.1.562.2.4.1.107.5.4.1.1.4
This variable represents the storage type value for the gvcIfDnaDdm tables.
OBJECT-TYPE    
  StorageType  

gvcIfDnaDdmIndex 1.3.6.1.4.1.562.2.4.1.107.5.4.1.1.10
This variable represents the index for the gvcIfDnaDdm tables.
OBJECT-TYPE    
  NonReplicated  

gvcIfDnaDdmLanAdTable 1.3.6.1.4.1.562.2.4.1.107.5.4.10
This group defines the LAN MAC and SAP address for a given WAN NPI and DNA address.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaDdmLanAdEntry

gvcIfDnaDdmLanAdEntry 1.3.6.1.4.1.562.2.4.1.107.5.4.10.1
An entry in the gvcIfDnaDdmLanAdTable.
OBJECT-TYPE    
  GvcIfDnaDdmLanAdEntry  

gvcIfDnaDdmMac 1.3.6.1.4.1.562.2.4.1.107.5.4.10.1.2
This attribute specifies a locally or globally administered MAC address of a LAN device.
OBJECT-TYPE    
  DashedHexString SIZE(6)  

gvcIfDnaDdmSap 1.3.6.1.4.1.562.2.4.1.107.5.4.10.1.3
This attribute specifies a SAP identifier on the LAN device identified by the mac.
OBJECT-TYPE    
  Hex 2..254  

gvcIfDnaDdmDmoTable 1.3.6.1.4.1.562.2.4.1.107.5.4.11
This group defines the device monitoring options.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaDdmDmoEntry

gvcIfDnaDdmDmoEntry 1.3.6.1.4.1.562.2.4.1.107.5.4.11.1
An entry in the gvcIfDnaDdmDmoTable.
OBJECT-TYPE    
  GvcIfDnaDdmDmoEntry  

gvcIfDnaDdmDeviceMonitoring 1.3.6.1.4.1.562.2.4.1.107.5.4.11.1.1
This attribute specifies wether device monitoring for the device specified in mac is enabled or disabled.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

gvcIfDnaDdmClearVcsWhenUnreachable 1.3.6.1.4.1.562.2.4.1.107.5.4.11.1.2
This attribute specifies wether to clear or not existing VCs when deviceStatus changes from reachable to unreachable.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

gvcIfDnaDdmDeviceMonitoringTimer 1.3.6.1.4.1.562.2.4.1.107.5.4.11.1.3
This attribute specifies the wait period between 2 consecutive device monitoring sequences. A device monitoring sequence is characterized by one of the following: up to maxTestRetry TEST commands sent and a TEST response received or up to maxTestRetry of TEST commands sent and no TEST response received.
OBJECT-TYPE    
  Unsigned32 1..255  

gvcIfDnaDdmTestResponseTimer 1.3.6.1.4.1.562.2.4.1.107.5.4.11.1.4
This attribute specifies the wait period between 2 consecutive TEST commands sent during one device monitoring sequence. A device monitoring sequence is characterized by one of the following: up to maxTestRetry TEST commands sent and a TEST response received or up to maxTestRetry of TEST commands sent and no TEST response received.
OBJECT-TYPE    
  Unsigned32 1..30  

gvcIfDnaDdmMaximumTestRetry 1.3.6.1.4.1.562.2.4.1.107.5.4.11.1.5
This attribute specifies the maximum number of TEST commands sent during one device monitoring sequence. A device monitoring sequence is characterized by one of the following: up to maxTestRetry TEST commands sent and a TEST response received or up to maxTestRetry of TEST commands sent and no TEST response received.
OBJECT-TYPE    
  Unsigned32 1..100  

gvcIfDnaDdmDevOpTable 1.3.6.1.4.1.562.2.4.1.107.5.4.12
This group specifies the operational attributes for devices that are potentially reachable by the SNA DLR service.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaDdmDevOpEntry

gvcIfDnaDdmDevOpEntry 1.3.6.1.4.1.562.2.4.1.107.5.4.12.1
An entry in the gvcIfDnaDdmDevOpTable.
OBJECT-TYPE    
  GvcIfDnaDdmDevOpEntry  

gvcIfDnaDdmDeviceStatus 1.3.6.1.4.1.562.2.4.1.107.5.4.12.1.1
This attribute indicates whether the local device specified by mac is reachable or unreachable from this SNA DLR interface. The device status is determined by the SNA DLR service by sending a TEST frame with the Poll bit set to the device periodically. If a TEST frame with the Final bit set is received from the device then the device status becomes reachable; otherwise the device status is unreachable. When the device status is reachable, connections to this device are accepted. When the device status is unreachable, existing connections to the device are cleared and new connections are cleared to hunt or redirection services.
OBJECT-TYPE    
  INTEGER unreachable(0), reachable(1)  

gvcIfDnaDdmActiveLinkStations 1.3.6.1.4.1.562.2.4.1.107.5.4.12.1.2
This attribute indicates the number of active link station connections using this device mapping component. It includes the link stations using the Qllc and the Frame-Relay connections.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDnaDdmLastTimeUnreachable 1.3.6.1.4.1.562.2.4.1.107.5.4.12.1.3
This attribute indicates the last time the deviceStatus changed from reachable to unreachable.
OBJECT-TYPE    
  EnterpriseDateAndTime SIZE(0 | 19)  

gvcIfDnaDdmLastTimeReachable 1.3.6.1.4.1.562.2.4.1.107.5.4.12.1.4
This attribute indicates the last time the deviceStatus changed from unreachable to reachable.
OBJECT-TYPE    
  EnterpriseDateAndTime SIZE(0 | 19)  

gvcIfDnaDdmDeviceUnreachable 1.3.6.1.4.1.562.2.4.1.107.5.4.12.1.5
This attribute counts the number of times the deviceStatus changed from reachable to unreachable. When the maximum count is exceeded the count wraps to zero.
OBJECT-TYPE    
  Counter32  

gvcIfDnaDdmMonitoringLcn 1.3.6.1.4.1.562.2.4.1.107.5.4.12.1.6
This attribute indicates the instance of the GvcIf/n Lcn that is reserved for monitoring the device indicated by the mac.
OBJECT-TYPE    
  INTEGER 1..4095  

gvcIfDnaSdm 1.3.6.1.4.1.562.2.4.1.107.5.5
OBJECT IDENTIFIER    

gvcIfDnaSdmRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.5.5.1
This entry controls the addition and deletion of gvcIfDnaSdm components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaSdmRowStatusEntry

gvcIfDnaSdmRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.5.5.1.1
A single entry in the table represents a single gvcIfDnaSdm component.
OBJECT-TYPE    
  GvcIfDnaSdmRowStatusEntry  

gvcIfDnaSdmRowStatus 1.3.6.1.4.1.562.2.4.1.107.5.5.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDnaSdm components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDnaSdmComponentName 1.3.6.1.4.1.562.2.4.1.107.5.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDnaSdmStorageType 1.3.6.1.4.1.562.2.4.1.107.5.5.1.1.4
This variable represents the storage type value for the gvcIfDnaSdm tables.
OBJECT-TYPE    
  StorageType  

gvcIfDnaSdmIndex 1.3.6.1.4.1.562.2.4.1.107.5.5.1.1.10
This variable represents the index for the gvcIfDnaSdm tables.
OBJECT-TYPE    
  DigitString SIZE(1..15)  

gvcIfDnaSdmLanAdTable 1.3.6.1.4.1.562.2.4.1.107.5.5.10
This group defines the LAN MAC and SAP address for a given WAN NPI and DNA address.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaSdmLanAdEntry

gvcIfDnaSdmLanAdEntry 1.3.6.1.4.1.562.2.4.1.107.5.5.10.1
An entry in the gvcIfDnaSdmLanAdTable.
OBJECT-TYPE    
  GvcIfDnaSdmLanAdEntry  

gvcIfDnaSdmMac 1.3.6.1.4.1.562.2.4.1.107.5.5.10.1.2
This attribute specifies a locally or globally administered MAC address of a LAN device.
OBJECT-TYPE    
  DashedHexString SIZE(6)  

gvcIfDnaSdmSap 1.3.6.1.4.1.562.2.4.1.107.5.5.10.1.3
This attribute specifies a SAP identifier on the LAN device identified by the mac.
OBJECT-TYPE    
  Hex 2..254  

gvcIfDnaSdmDmoTable 1.3.6.1.4.1.562.2.4.1.107.5.5.11
This group defines the device monitoring options.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaSdmDmoEntry

gvcIfDnaSdmDmoEntry 1.3.6.1.4.1.562.2.4.1.107.5.5.11.1
An entry in the gvcIfDnaSdmDmoTable.
OBJECT-TYPE    
  GvcIfDnaSdmDmoEntry  

gvcIfDnaSdmDeviceMonitoring 1.3.6.1.4.1.562.2.4.1.107.5.5.11.1.1
This attribute specifies wether device monitoring for the device specified in mac is enabled or disabled.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

gvcIfDnaSdmClearVcsWhenUnreachable 1.3.6.1.4.1.562.2.4.1.107.5.5.11.1.2
This attribute specifies wether to clear or not existing VCs when deviceStatus changes from reachable to unreachable.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

gvcIfDnaSdmDeviceMonitoringTimer 1.3.6.1.4.1.562.2.4.1.107.5.5.11.1.3
This attribute specifies the wait period between 2 consecutive device monitoring sequences. A device monitoring sequence is characterized by one of the following: up to maxTestRetry TEST commands sent and a TEST response received or up to maxTestRetry of TEST commands sent and no TEST response received.
OBJECT-TYPE    
  Unsigned32 1..255  

gvcIfDnaSdmTestResponseTimer 1.3.6.1.4.1.562.2.4.1.107.5.5.11.1.4
This attribute specifies the wait period between 2 consecutive TEST commands sent during one device monitoring sequence. A device monitoring sequence is characterized by one of the following: up to maxTestRetry TEST commands sent and a TEST response received or up to maxTestRetry of TEST commands sent and no TEST response received.
OBJECT-TYPE    
  Unsigned32 1..30  

gvcIfDnaSdmMaximumTestRetry 1.3.6.1.4.1.562.2.4.1.107.5.5.11.1.5
This attribute specifies the maximum number of TEST commands sent during one device monitoring sequence. A device monitoring sequence is characterized by one of the following: up to maxTestRetry TEST commands sent and a TEST response received or up to maxTestRetry of TEST commands sent and no TEST response received.
OBJECT-TYPE    
  Unsigned32 1..100  

gvcIfDnaSdmDevOpTable 1.3.6.1.4.1.562.2.4.1.107.5.5.12
This group specifies the operational attributes for devices that are potentially reachable by the SNA DLR service.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaSdmDevOpEntry

gvcIfDnaSdmDevOpEntry 1.3.6.1.4.1.562.2.4.1.107.5.5.12.1
An entry in the gvcIfDnaSdmDevOpTable.
OBJECT-TYPE    
  GvcIfDnaSdmDevOpEntry  

gvcIfDnaSdmDeviceStatus 1.3.6.1.4.1.562.2.4.1.107.5.5.12.1.1
This attribute indicates whether the local device specified by mac is reachable or unreachable from this SNA DLR interface. The device status is determined by the SNA DLR service by sending a TEST frame with the Poll bit set to the device periodically. If a TEST frame with the Final bit set is received from the device then the device status becomes reachable; otherwise the device status is unreachable. When the device status is reachable, connections to this device are accepted. When the device status is unreachable, existing connections to the device are cleared and new connections are cleared to hunt or redirection services.
OBJECT-TYPE    
  INTEGER unreachable(0), reachable(1)  

gvcIfDnaSdmActiveLinkStations 1.3.6.1.4.1.562.2.4.1.107.5.5.12.1.2
This attribute indicates the number of active link station connections using this device mapping component. It includes the link stations using the Qllc and the Frame-Relay connections.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDnaSdmLastTimeUnreachable 1.3.6.1.4.1.562.2.4.1.107.5.5.12.1.3
This attribute indicates the last time the deviceStatus changed from reachable to unreachable.
OBJECT-TYPE    
  EnterpriseDateAndTime SIZE(0 | 19)  

gvcIfDnaSdmLastTimeReachable 1.3.6.1.4.1.562.2.4.1.107.5.5.12.1.4
This attribute indicates the last time the deviceStatus changed from unreachable to reachable.
OBJECT-TYPE    
  EnterpriseDateAndTime SIZE(0 | 19)  

gvcIfDnaSdmDeviceUnreachable 1.3.6.1.4.1.562.2.4.1.107.5.5.12.1.5
This attribute counts the number of times the deviceStatus changed from reachable to unreachable. When the maximum count is exceeded the count wraps to zero.
OBJECT-TYPE    
  Counter32  

gvcIfDnaSdmMonitoringLcn 1.3.6.1.4.1.562.2.4.1.107.5.5.12.1.6
This attribute indicates the instance of the GvcIf/n Lcn that is reserved for monitoring the device indicated by the mac.
OBJECT-TYPE    
  INTEGER 1..4095  

gvcIfDnaAddrTable 1.3.6.1.4.1.562.2.4.1.107.5.11
This group contains attributes common to all DNAs. Every DNA used in the network is defined with this group of 2 attributes, a string of address digits and a NPI.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaAddrEntry

gvcIfDnaAddrEntry 1.3.6.1.4.1.562.2.4.1.107.5.11.1
An entry in the gvcIfDnaAddrTable.
OBJECT-TYPE    
  GvcIfDnaAddrEntry  

gvcIfDnaNumberingPlanIndicator 1.3.6.1.4.1.562.2.4.1.107.5.11.1.1
This attribute indicates the Numbering Plan Indicator (NPI) of the Dna that is entered. Address may belong to X.121 or E.164 plans.
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

gvcIfDnaDataNetworkAddress 1.3.6.1.4.1.562.2.4.1.107.5.11.1.2
This attribute contains digits which form the unique identifier of the customer interface. It can be compared (approximation only) to telephone number where the telephone number identifies a unique telephone set. Dna digits are selected and assigned by network operators.
OBJECT-TYPE    
  DigitString SIZE(1..15)  

gvcIfDnaOutgoingOptionsTable 1.3.6.1.4.1.562.2.4.1.107.5.12
This group defines call options of a Dna for calls which are made out of the interface represented by Dna.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaOutgoingOptionsEntry

gvcIfDnaOutgoingOptionsEntry 1.3.6.1.4.1.562.2.4.1.107.5.12.1
An entry in the gvcIfDnaOutgoingOptionsTable.
OBJECT-TYPE    
  GvcIfDnaOutgoingOptionsEntry  

gvcIfDnaOutDefaultPriority 1.3.6.1.4.1.562.2.4.1.107.5.12.1.7
This attribute, if set to normal indicates that the default priority for outgoing calls (from the DTE to the network) for this particular Dna is normal priority - if the priority is not specified by the DTE. If this attribute is set to high then the default priority for outgoing calls using this particular Dna is high priority. This option can also be included in X.25 signalling, in which case it will be overruled.
OBJECT-TYPE    
  INTEGER normal(0), high(1)  

gvcIfDnaOutDefaultPathSensitivity 1.3.6.1.4.1.562.2.4.1.107.5.12.1.11
This attribute specifies the default class of routing for delay/ throughput sensitive routing for all outgoing calls (from the DTE to the network)for this particular Dna. The chosen default class of routing applies to all outgoing calls established using this Dna, and applies to the packets travelling in both directions on all outgoing calls (local to remote, and remote to local). For incoming calls, the default class of routing is chosen by the calling party (as opposed to DPN, where either end of the call can choose the default routing class). This attribute, if set to a value of throughput, indicates that the default class of routing is throughput sensitive routing. If set to a value of delay, then the default class of routing is delay sensitive routing. In the future, the class of routing sensitivity may be overridden at the calling end of the call as follows: The default class of routing sensitivity can be overridden by the DTE in the call request packet through the TDS&I (Transit Delay Selection & Indication) if the DTE supports this facility. Whether or not the DTE is permitted to signal the TDS&I facility will depend on the DTE (i.e.: TDS&I is supported in X.25 only), and will depend on whether the port is configured to permit the TDS&I facility. In Passport, the treatment of DTE facilities (for example, NUI, RPOA, and TDS&I) not fully defined yet since it is not required. At the point in time when it is required, the parameter to control whether or not the DTE is permitted to signal the TDS&I will be in a Facility Treatment component. Currently, the default is to disallow the TDS&I facility from the DTE.
OBJECT-TYPE    
  INTEGER throughput(0), delay(1)  

gvcIfDnaOutDefaultPathReliability 1.3.6.1.4.1.562.2.4.1.107.5.12.1.14
This attribute specifies the default class of routing for reliability routing for all outgoing calls (from the DTE to the network) this particular Dna. The chosen default class of routing applies to all outgoing calls established using this Dna, and applies to the packets travelling in both directions on all outgoing calls (local to remote, and remote to local). For incoming calls, the default class of routing is chosen by the calling party (as opposed to DPN, where either end of the call can choose the default routing class). This attribute, if set to a value of normal, indicates that the default class of routing is normal reliability routing. If set to a value of high, then the default class of routing is high reliability routing. High reliability is the standard choice for most DPN and Passport services. It usually indicates that packets are overflowed or retransmitted at various routing levels. Typically high reliability results in duplication and disordering of packets in the network when errors are detected or during link congestion. However, the Vc handles the duplication and disordering to ensure that packets are delivered to the DTE properly. For the Frame Relay service, duplication of packets is not desired, in which case, normal reliability may be chosen as the preferred class of routing.
OBJECT-TYPE    
  INTEGER high(0), normal(1)  

gvcIfDnaOutAccess 1.3.6.1.4.1.562.2.4.1.107.5.12.1.17
This attribute is an extension of the Closed User Group (CUG), as follows: This attribute, if set to a value of allowed indicates that outgoing calls (from the DTE to the network) the open (non-CUG) of the network are permitted. It also permits outgoing calls to DTEs that have Incoming Access capabilities. If set to a value of disallowed, then such calls cannot be made using this Dna - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Closed User Group with Outgoing Access' feature for Dnas in that outgoing access is granted if this attribute is set to a value of allowed.
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

gvcIfDnaDefaultTransferPriority 1.3.6.1.4.1.562.2.4.1.107.5.12.1.18
This attribute specifies the default transfer priority to network for all outgoing calls using this particular Dna. It can be overRide by the transferPriority provisioned in the DLCI Direct Call sub- component. The transfer priority is a preference specified by an application according to its time-sensitivity requirement. Frames with high transfer priority are served by the network before the frames with normal priority. The transfer priority in Passport determines two things in use: trunk queue (among interrupting, delay, throughput), and routing metric (between delay and throughput). The following table descibes the details of each transfer priority: The default of outDefaultTransferPriority is normal.
OBJECT-TYPE    
  INTEGER normal(0), high(9)  

gvcIfDnaTransferPriorityOverRide 1.3.6.1.4.1.562.2.4.1.107.5.12.1.19
When this attribute is set to yes in the call request, the called end will use the calling end provisioning data on transfer priority to override its own provisioning data. If it is set no, the called end will use its own provisioning data on transfer priority. The default of outTransferPriorityOverRide is yes.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

gvcIfDnaIncomingOptionsTable 1.3.6.1.4.1.562.2.4.1.107.5.13
IncomingOptions defines set of options for incoming calls. These options are used for calls arriving to the interface represented by Dna. For calls originated from the interface, IncomingOptions attributes are not used.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaIncomingOptionsEntry

gvcIfDnaIncomingOptionsEntry 1.3.6.1.4.1.562.2.4.1.107.5.13.1
An entry in the gvcIfDnaIncomingOptionsTable.
OBJECT-TYPE    
  GvcIfDnaIncomingOptionsEntry  

gvcIfDnaIncCalls 1.3.6.1.4.1.562.2.4.1.107.5.13.1.1
This attribute, if set to a value of allowed indicates that incoming calls (from the network to the DTE) be made to this Dna. If set to a value of disallowed, then incoming calls cannot be made to this Dna - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Incoming Calls Barred' feature for Dnas in that incoming calls are barred if this attribute is set to a value of disallowed. Either outCalls, or incCalls (or both) be set to a value of allowed for this Dna to be usable.
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

gvcIfDnaIncHighPriorityReverseCharge 1.3.6.1.4.1.562.2.4.1.107.5.13.1.2
This attribute, if set to a value of allowed indicates that incoming high priority, reverse charged calls (from the network to the DTE) be made to this Dna. If set to a value of disallowed, then such calls cannot be made to this Dna - such calls will be cleared by the local DCE. This attribute, together with the incNormalPriorityReverseChargeCalls attribute corresponds to the CCITT 'Reverse Charging Acceptance' feature for Dnas in that reverse charged calls are accepted if both attributes are set to a value of allowed. This attribute is ignored if the corresponding attribute, incCalls is set to a value of disallowed.
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

gvcIfDnaIncNormalPriorityReverseCharge 1.3.6.1.4.1.562.2.4.1.107.5.13.1.3
This attribute, if set to a value of allowed indicates that incoming normal priority, reverse charged calls (from the network to the DTE) be made to this Dna. If set to a value of disallowed, then such calls cannot be made to this Dna - such calls will be cleared by the local DCE. This attribute, together with the incHighPriorityReverseChargeCalls attribute corresponds to the CCITT 'Reverse Charging Acceptance' feature for Dnas in that reverse charged calls are accepted if both attributes are set to a value of allowed. This attribute is ignored if the corresponding attribute, incCalls is set to a value of disallowed.
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

gvcIfDnaIncIntlNormalCharge 1.3.6.1.4.1.562.2.4.1.107.5.13.1.4
This attribute, if set to a value of allowed indicates that incoming international normal charged calls (from the network to the DTE) be made to this Dna. If set to a value of disallowed, then such calls cannot be made to this Dna - such calls will be cleared by the local DCE. This attribute also currently controls access to/from the E.164 numbering plan, and if set to a value of allowed, then cross- numbering plan calls (also normal charged) allowed. This attribute is ignored if the corresponding attribute, incCalls is set to a value of disallowed.
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

gvcIfDnaIncIntlReverseCharge 1.3.6.1.4.1.562.2.4.1.107.5.13.1.5
This attribute, if set to a value of allowed indicates that incoming international reverse charged calls (from the network to the DTE) be made to this Dna. If set to a value of disallowed, then such calls cannot be made to this Dna - such calls will be cleared by the local DCE. This attribute also currently controls access to/from the E.164 numbering plan, and if set to a value of allowed, then cross- numbering plan calls (also normal charged) allowed. This attribute is ignored if the corresponding attribute, incCalls is set to a value of disallowed.
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

gvcIfDnaIncSameService 1.3.6.1.4.1.562.2.4.1.107.5.13.1.7
This attribute, if set to a value of allowed indicates that incoming calls from the same service type (e.g.: X.25, ITI, SNA) (from the network to the DTE) be made to this Dna. If set to a value of disallowed, then such calls cannot be made to this Dna - such calls will be cleared by the local DCE. This attribute is ignored if the corresponding attribute, incCalls is set to a value of disallowed.
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

gvcIfDnaIncAccess 1.3.6.1.4.1.562.2.4.1.107.5.13.1.9
This attribute is an extension of the Closed User Group (CUG), as follows: This attribute, if set to a value of allowed indicates that incoming calls (from the network to the DTE) the open (non-CUG) of the network are permitted. It also permits incoming calls from DTEs that have Outgoing Access capabilities. If set to a value of disallowed, then such calls cannot be made to this Dna - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Closed User Group with Incoming Access' feature for Dnas in that incoming access is granted if this attribute is set to a value of allowed.
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

gvcIfDnaCallOptionsTable 1.3.6.1.4.1.562.2.4.1.107.5.14
CallOptions group defines additional options for calls not related directly to direction of a call.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDnaCallOptionsEntry

gvcIfDnaCallOptionsEntry 1.3.6.1.4.1.562.2.4.1.107.5.14.1
An entry in the gvcIfDnaCallOptionsTable.
OBJECT-TYPE    
  GvcIfDnaCallOptionsEntry  

gvcIfDnaServiceCategory 1.3.6.1.4.1.562.2.4.1.107.5.14.1.1
This attribute is assigned for each different type of service within which this Dna is configured. It is placed into the Service Category attribute in the accounting record by both ends of the Vc.
OBJECT-TYPE    
  INTEGER gsp(0), x25(1), enhancedIti(2), ncs(3), mlti(4), sm(5), ici(6), dsp3270(7), iam(8), mlhi(9), term3270(10), iti(11), bsi(13), hostIti(14), x75(15), hdsp3270(16), api3201(20), sdlc(21), snaMultiHost(22), redirectionServ(23), trSnaTpad(24), offnetNui(25), gasServer(26), vapServer(28), vapAgent(29), frameRelay(30), ipiVc(31), gvcIf(32)  

gvcIfDnaPacketSizes 1.3.6.1.4.1.562.2.4.1.107.5.14.1.2
This attribute indicates the allowable packet sizes supported for call setup using this Dna. CCITT recommends that packet size 128 always be supported. Description of bits: n16(0) n32(1) n64(2) n128(3) n256(4) n512(5) n1024(6) n2048(7) n4096(8)
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

gvcIfDnaDefaultRecvFrmNetworkPacketSize 1.3.6.1.4.1.562.2.4.1.107.5.14.1.3
This attribute indicates the default local receive packet size from network to DTE for all calls using this particular Dna.
OBJECT-TYPE    
  INTEGER n16(4), n32(5), n64(6), n128(7), n256(8), n512(9), n1024(10), n2048(11), n4096(12)  

gvcIfDnaDefaultSendToNetworkPacketSize 1.3.6.1.4.1.562.2.4.1.107.5.14.1.4
This attribute indicates the default local send packet size from DTE to network for all calls using this particular Dna.
OBJECT-TYPE    
  INTEGER n16(4), n32(5), n64(6), n128(7), n256(8), n512(9), n1024(10), n2048(11), n4096(12)  

gvcIfDnaDefaultRecvFrmNetworkThruputClass 1.3.6.1.4.1.562.2.4.1.107.5.14.1.5
This attribute indicates the default receive throughput class for all calls using this particular Dna.
OBJECT-TYPE    
  Unsigned32 0..15  

gvcIfDnaDefaultSendToNetworkThruputClass 1.3.6.1.4.1.562.2.4.1.107.5.14.1.6
This attribute indicates the default send throughput class for all calls using this particular Dna.
OBJECT-TYPE    
  Unsigned32 0..15  

gvcIfDnaDefaultRecvFrmNetworkWindowSize 1.3.6.1.4.1.562.2.4.1.107.5.14.1.7
This attribute indicates the default number of data packets that can be received by the DTE from the DCE before more packets can be received. This view is oriented with respect to the DTE.
OBJECT-TYPE    
  Unsigned32 1..7  

gvcIfDnaDefaultSendToNetworkWindowSize 1.3.6.1.4.1.562.2.4.1.107.5.14.1.8
This attribute indicates the number of data packets that can be transmitted from the DTE to the DCE and must be acknowledged before more packets can be transmitted.
OBJECT-TYPE    
  Unsigned32 1..7  

gvcIfDnaPacketSizeNegotiation 1.3.6.1.4.1.562.2.4.1.107.5.14.1.9
This attribute, if set to local indicates that packet sizes can be negotiated locally at the interface irrespective of the remote interface. If set to endtoEnd, then local negotiation is not permitted and packet sizes are negotiated between 2 ends of Vc.
OBJECT-TYPE    
  INTEGER endToEnd(0), local(1)  

gvcIfDnaCugFormat 1.3.6.1.4.1.562.2.4.1.107.5.14.1.10
This attribute specifies which Cug format is used when DTE signals CUG indices, basic or extended. This attribute, if set to extended indicates that the DTE signals and receives CUG indices in extended CUG format. If set to a value of basic, then the DTE signals and receives CUG indices in the basic CUG format.
OBJECT-TYPE    
  INTEGER basic(0), extended(1)  

gvcIfDnaAccountClass 1.3.6.1.4.1.562.2.4.1.107.5.14.1.16
This attribute specifies the accounting class which is reserved for network operations usage. Its value is returned in the accounting record in the local and remote service type attributes. Use of this attribute is decided by network operator and it is an arbitrary number.
OBJECT-TYPE    
  Unsigned32 0..255  

gvcIfDnaAccountCollection 1.3.6.1.4.1.562.2.4.1.107.5.14.1.17
This attribute indicates that accounting records are to be collected by the network for the various reasons: billing, test, study, auditing. The last of the parameters, force, indicates that accounting records are to be collected irrespective of other collection reasons. If none of these reasons are set, then accounting will be suppressed. Description of bits: bill(0) test(1) study(2) audit(3) force(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

gvcIfDnaServiceExchange 1.3.6.1.4.1.562.2.4.1.107.5.14.1.18
This attribute is an arbitrary number, entered by the network operator. The value of serviceExchange is included in the accounting record generated by Vc.
OBJECT-TYPE    
  Unsigned32 0..255  

gvcIfRg 1.3.6.1.4.1.562.2.4.1.107.6
OBJECT IDENTIFIER    

gvcIfRgRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.6.1
This entry controls the addition and deletion of gvcIfRg components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfRgRowStatusEntry

gvcIfRgRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.6.1.1
A single entry in the table represents a single gvcIfRg component.
OBJECT-TYPE    
  GvcIfRgRowStatusEntry  

gvcIfRgRowStatus 1.3.6.1.4.1.562.2.4.1.107.6.1.1.1
This variable is used as the basis for SNMP naming of gvcIfRg components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfRgComponentName 1.3.6.1.4.1.562.2.4.1.107.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfRgStorageType 1.3.6.1.4.1.562.2.4.1.107.6.1.1.4
This variable represents the storage type value for the gvcIfRg tables.
OBJECT-TYPE    
  StorageType  

gvcIfRgIndex 1.3.6.1.4.1.562.2.4.1.107.6.1.1.10
This variable represents the index for the gvcIfRg tables.
OBJECT-TYPE    
  Integer32 0..0  

gvcIfRgIfEntryTable 1.3.6.1.4.1.562.2.4.1.107.6.10
This group contains the provisionable attributes for the ifEntry.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfRgIfEntryEntry

gvcIfRgIfEntryEntry 1.3.6.1.4.1.562.2.4.1.107.6.10.1
An entry in the gvcIfRgIfEntryTable.
OBJECT-TYPE    
  GvcIfRgIfEntryEntry  

gvcIfRgIfAdminStatus 1.3.6.1.4.1.562.2.4.1.107.6.10.1.1
The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

gvcIfRgIfIndex 1.3.6.1.4.1.562.2.4.1.107.6.10.1.2
This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
OBJECT-TYPE    
  InterfaceIndex 1..65535  

gvcIfRgProvTable 1.3.6.1.4.1.562.2.4.1.107.6.11
This group contains the provisioned attributes in the remote group component.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfRgProvEntry

gvcIfRgProvEntry 1.3.6.1.4.1.562.2.4.1.107.6.11.1
An entry in the gvcIfRgProvTable.
OBJECT-TYPE    
  GvcIfRgProvEntry  

gvcIfRgLinkToProtocolPort 1.3.6.1.4.1.562.2.4.1.107.6.11.1.1
This attribute specifies a two way link between this GvcIf RemoteGroup and a VirtualRouter/n ProtocolPort/name component which enables the communication between WAN addressable devices and LAN addressable devices.
OBJECT-TYPE    
  Link  

gvcIfRgOperStatusTable 1.3.6.1.4.1.562.2.4.1.107.6.12
This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfRgOperStatusEntry

gvcIfRgOperStatusEntry 1.3.6.1.4.1.562.2.4.1.107.6.12.1
An entry in the gvcIfRgOperStatusTable.
OBJECT-TYPE    
  GvcIfRgOperStatusEntry  

gvcIfRgSnmpOperStatus 1.3.6.1.4.1.562.2.4.1.107.6.12.1.1
The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

gvcIfDlci 1.3.6.1.4.1.562.2.4.1.107.7
OBJECT IDENTIFIER    

gvcIfDlciRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.7.1
This entry controls the addition and deletion of gvcIfDlci components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciRowStatusEntry

gvcIfDlciRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.7.1.1
A single entry in the table represents a single gvcIfDlci component.
OBJECT-TYPE    
  GvcIfDlciRowStatusEntry  

gvcIfDlciRowStatus 1.3.6.1.4.1.562.2.4.1.107.7.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDlci components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDlciComponentName 1.3.6.1.4.1.562.2.4.1.107.7.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDlciStorageType 1.3.6.1.4.1.562.2.4.1.107.7.1.1.4
This variable represents the storage type value for the gvcIfDlci tables.
OBJECT-TYPE    
  StorageType  

gvcIfDlciIndex 1.3.6.1.4.1.562.2.4.1.107.7.1.1.10
This variable represents the index for the gvcIfDlci tables.
OBJECT-TYPE    
  Integer32 16..4095  

gvcIfDlciDc 1.3.6.1.4.1.562.2.4.1.107.7.2
OBJECT IDENTIFIER    

gvcIfDlciDcRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.7.2.1
This entry controls the addition and deletion of gvcIfDlciDc components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciDcRowStatusEntry

gvcIfDlciDcRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.7.2.1.1
A single entry in the table represents a single gvcIfDlciDc component.
OBJECT-TYPE    
  GvcIfDlciDcRowStatusEntry  

gvcIfDlciDcRowStatus 1.3.6.1.4.1.562.2.4.1.107.7.2.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDlciDc components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDlciDcComponentName 1.3.6.1.4.1.562.2.4.1.107.7.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDlciDcStorageType 1.3.6.1.4.1.562.2.4.1.107.7.2.1.1.4
This variable represents the storage type value for the gvcIfDlciDc tables.
OBJECT-TYPE    
  StorageType  

gvcIfDlciDcIndex 1.3.6.1.4.1.562.2.4.1.107.7.2.1.1.10
This variable represents the index for the gvcIfDlciDc tables.
OBJECT-TYPE    
  NonReplicated  

gvcIfDlciDcOptionsTable 1.3.6.1.4.1.562.2.4.1.107.7.2.10
Options group defines attributes associated with direct call. It defines complete connection in terms of path and call options. This connection can be permanent (PVC).
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciDcOptionsEntry

gvcIfDlciDcOptionsEntry 1.3.6.1.4.1.562.2.4.1.107.7.2.10.1
An entry in the gvcIfDlciDcOptionsTable.
OBJECT-TYPE    
  GvcIfDlciDcOptionsEntry  

gvcIfDlciDcRemoteNpi 1.3.6.1.4.1.562.2.4.1.107.7.2.10.1.3
This attribute specifies the numbering plan used in the remoteDna.
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

gvcIfDlciDcRemoteDna 1.3.6.1.4.1.562.2.4.1.107.7.2.10.1.4
This attribute specifies the Data Network Address (Dna) of the remote. This is the called (destination) DTE address (Dna) to which this direct call will be sent.
OBJECT-TYPE    
  DigitString SIZE(1..15)  

gvcIfDlciDcRemoteDlci 1.3.6.1.4.1.562.2.4.1.107.7.2.10.1.5
This attribute specifies the remote DLCI (Logical Channel Number) - it is used only for PVCs, where attribute type is set to permanentMaster or permanentSlave or permanentBackupSlave.
OBJECT-TYPE    
  Unsigned32 0..4095  

gvcIfDlciDcType 1.3.6.1.4.1.562.2.4.1.107.7.2.10.1.6
This attribute specifies the type of Vc call: permanentMaster, permanentSlave, permanentSlaveWithBackup, permanentBackupSlave. If the value is set to permanentMaster, then a permanent connection will be established between 2 ends. The remote end must be defined as a permanentSlave, permanentBackupSlave or permanentSlaveWithBackup. The connection cannot be established if the remote end is defined as anything else. The end defined as permanentMaster always initiates the calls. It will attempt to call once per minute. If the value is set to permanentSlave then a permanent connection will be established between 2 ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote end is defined as anything else. The permanentSlave end will attempt to call once per minute. If the value is set to permanentSlaveWithBackup then a permanent connection will be established between the 2 ends . The remote end must be defined as a permanentMaster. The Connection cannot be established if the remote end is defined as anything else. The permanentSlaveWithBackup end will attempt to call once per minute. If the value is set to permanentBackupSlave then a permanent connection will be established between the 2 ends only if the permanentMaster end is disconnected from the permanentSlaveWithBackup end and a backup call is established by the redirection system. If the permanentSlaveWithBackup interface becomes visible again, the permanentBackupSlave end is disconnected and the permanentSlaveWithBackup end is reconnected to the permanentMaster end. The permanentBackupSlave end does not try to establish pvc call.
OBJECT-TYPE    
  INTEGER permanentMaster(1), permanentSlave(2), permanentBackupSlave(3), permanentSlaveWithBackup(4)  

gvcIfDlciDcTransferPriority 1.3.6.1.4.1.562.2.4.1.107.7.2.10.1.9
This attribute specifies the transfer priority to network for the outgoing calls using this particular DLCI. It overRides the defaultTransferPriority provisioned in its associated Dna component. The transfer priority is a preference specified by an application according to its delay-sensitivity requirement. Frames with high transfer priority are served by the network before the frames with normal priority. Each transfer priority contains a predetermined setting for trunk queue (interrupting, delay or throughput), and routing metric (delay or throughput). When the transfer priority is set at high, the trunk queue is set to high, the routing metric is set to delay. When the transfer priority is set at normal, the trunk queue is set to normal, the routing metric is set to throughput. The default of transferPriority is useDnaDefTP. It means using the provisioning value under defaultTransferPriority of its associated Dna for this DLCI.
OBJECT-TYPE    
  INTEGER normal(0), high(9), useDnaDefTP(255)  

gvcIfDlciDcDiscardPriority 1.3.6.1.4.1.562.2.4.1.107.7.2.10.1.10
This attribute specifies the discard priority for outgoing call using this DLCI. The discard priority has three provisioning values: normal, high, and useDnaDefPriority. Traffic with normal priority is discarded first than the traffic with high priority. The Dna default value (provisioned by outDefaultPriority) is taken if this attribute is set to the value useDnaDefPriority. The default of discardPriority is useDnaDefPriority.
OBJECT-TYPE    
  INTEGER normal(0), high(1), useDnaDefPriority(3)  

gvcIfDlciDcNfaTable 1.3.6.1.4.1.562.2.4.1.107.7.2.482
Two explicit attributes discardPriority and transferPriority are created to replace H.01 and H.30 in the group VcsDirectCallOptionsProv of this file. The migrate escape here (DcComponent::migrateFaxEscape) propagates the old provisioning data under H.01 and H.30 into discardPriority and transferPriority. The rule of the above propagation are: 0 in H.01 is equivalent to discardPriority 0; 1 in H.01 is equivalent to discardPriority 1. And 0 in H.30 is equivalent to transferPriority normal; 1 in H.30 is equivalent to transferPriority high. Please refer to discardPriority and transferPriority for more information on how to use them.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciDcNfaEntry

gvcIfDlciDcNfaEntry 1.3.6.1.4.1.562.2.4.1.107.7.2.482.1
An entry in the gvcIfDlciDcNfaTable.
OBJECT-TYPE    
  GvcIfDlciDcNfaEntry  

gvcIfDlciDcNfaIndex 1.3.6.1.4.1.562.2.4.1.107.7.2.482.1.1
This variable represents the index for the gvcIfDlciDcNfaTable.
OBJECT-TYPE    
  Integer32 1 | 48  

gvcIfDlciDcNfaValue 1.3.6.1.4.1.562.2.4.1.107.7.2.482.1.2
This variable represents an individual value for the gvcIfDlciDcNfaTable.
OBJECT-TYPE    
  HexString SIZE(0..128)  

gvcIfDlciDcNfaRowStatus 1.3.6.1.4.1.562.2.4.1.107.7.2.482.1.3
This variable is used to control the addition and deletion of individual values of the gvcIfDlciDcNfaTable.
OBJECT-TYPE    
  RowStatus  

gvcIfDlciVc 1.3.6.1.4.1.562.2.4.1.107.7.3
OBJECT IDENTIFIER    

gvcIfDlciVcRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.7.3.1
This entry controls the addition and deletion of gvcIfDlciVc components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciVcRowStatusEntry

gvcIfDlciVcRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.7.3.1.1
A single entry in the table represents a single gvcIfDlciVc component.
OBJECT-TYPE    
  GvcIfDlciVcRowStatusEntry  

gvcIfDlciVcRowStatus 1.3.6.1.4.1.562.2.4.1.107.7.3.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDlciVc components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDlciVcComponentName 1.3.6.1.4.1.562.2.4.1.107.7.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDlciVcStorageType 1.3.6.1.4.1.562.2.4.1.107.7.3.1.1.4
This variable represents the storage type value for the gvcIfDlciVc tables.
OBJECT-TYPE    
  StorageType  

gvcIfDlciVcIndex 1.3.6.1.4.1.562.2.4.1.107.7.3.1.1.10
This variable represents the index for the gvcIfDlciVc tables.
OBJECT-TYPE    
  NonReplicated  

gvcIfDlciVcCadTable 1.3.6.1.4.1.562.2.4.1.107.7.3.10
This group represents operational call data related to Frame Relay Vc. It can be displayed only for Frame Relay Vc which is created by application.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciVcCadEntry

gvcIfDlciVcCadEntry 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1
An entry in the gvcIfDlciVcCadTable.
OBJECT-TYPE    
  GvcIfDlciVcCadEntry  

gvcIfDlciVcType 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.1
This attribute displays the type of call, pvc,svc or spvc.
OBJECT-TYPE    
  INTEGER svc(0), pvc(1), spvc(2)  

gvcIfDlciVcState 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.2
This attribute displays the state of call control. P5 state is not supported but is listed for completness. Transitions from one state to another take very short time. state most often displayed is dataTransferP4.
OBJECT-TYPE    
  INTEGER creating(0), readyP1(1), dteWaitingP2(2), dceWaitingP3(3), dataTransferP4(4), unsupportedP5(5), dteClearRequestP6(6), dceClearIndicationP7(7), termination(8)  

gvcIfDlciVcPreviousState 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.3
This attribute displays the previous state of call control. This is a valuable field to determine how the processing is progressing.
OBJECT-TYPE    
  INTEGER creating(0), readyP1(1), dteWaitingP2(2), dceWaitingP3(3), dataTransferP4(4), unsupportedP5(5), dteClearRequestP6(6), dceClearIndicationP7(7), termination(8)  

gvcIfDlciVcDiagnosticCode 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.4
This attribute displays the internal substate of call control. It is used to further refine state of call processing.
OBJECT-TYPE    
  Unsigned32 0..255  

gvcIfDlciVcPreviousDiagnosticCode 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.5
This attribute displays the internal substate of call control. It is used to further refine state of call processing.
OBJECT-TYPE    
  Unsigned32 0..255  

gvcIfDlciVcCalledNpi 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.6
This attribute displays the Numbering Plan Indicator (NPI) of the called end.
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

gvcIfDlciVcCalledDna 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.7
This attribute displays the Data Network Address (Dna) of the called (destination) DTE to which this call is sent. This address if defined at recieving end will complete Vc connection.
OBJECT-TYPE    
  DigitString SIZE(1..15)  

gvcIfDlciVcCalledLcn 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.8
This attribute displays the Logical Channel Number of the called end. It is valid only after both ends of Vc exchanged relevant information.
OBJECT-TYPE    
  Unsigned32 1..65535  

gvcIfDlciVcCallingNpi 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.9
This attribute displays the Numbering Plan Indicator (NPI) of the calling end.
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

gvcIfDlciVcCallingDna 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.10
This attribute displays the Data Network Address (Dna) of the calling end.
OBJECT-TYPE    
  DigitString SIZE(1..15)  

gvcIfDlciVcCallingLcn 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.11
This attribute displays the Logical Channel Number of the calling end.
OBJECT-TYPE    
  Unsigned32 1..65535  

gvcIfDlciVcAccountingEnabled 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.12
This attribute indicates that this optional section of accounting record is suppressed or permitted. If accountingEnabled is yes, conditions for generation of accounting record were met. These conditions include billing options, vc recovery conditions and Module wide accounting data options.
OBJECT-TYPE    
  INTEGER yes(0), no(1)  

gvcIfDlciVcFastSelectCall 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.13
This attribute displays that this is a fast select call.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

gvcIfDlciVcPathReliability 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.19
This attribute displays the path reliability.
OBJECT-TYPE    
  INTEGER high(0), normal(1)  

gvcIfDlciVcAccountingEnd 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.20
This attribute indicates if this end should generate an accounting record. Normally, callingEnd is the end to generate an accounting record.
OBJECT-TYPE    
  INTEGER callingEnd(0), calledEnd(1)  

gvcIfDlciVcPriority 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.21
This attribute displays whether the call is a normal or a high priority call.
OBJECT-TYPE    
  INTEGER normal(0), high(1)  

gvcIfDlciVcSegmentSize 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.22
This attribute displays the segment size (in bytes) used on the call. It is used to calculate the number of segments transmitted and received.
OBJECT-TYPE    
  Unsigned32 0..4096  

gvcIfDlciVcMaxSubnetPktSize 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.27
This attribute indicates the maximum packet size allowed on the Vc.
OBJECT-TYPE    
  Unsigned32 0..4096  

gvcIfDlciVcRcosToNetwork 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.28
This attribute indicates the routing metric routing class of service to the network.
OBJECT-TYPE    
  INTEGER throughput(0), delay(1), multimedia(2)  

gvcIfDlciVcRcosFromNetwork 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.29
This attribute displays the routing metric Routing Class of Service from the Network.
OBJECT-TYPE    
  INTEGER throughput(0), delay(1), multimedia(2)  

gvcIfDlciVcEmissionPriorityToNetwork 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.30
This attribute displays the network internal emission priotity to the network.
OBJECT-TYPE    
  INTEGER normal(0), high(1), interrupting(2)  

gvcIfDlciVcEmissionPriorityFromNetwork 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.31
This attribute displays the network internal emission priotity from the network.
OBJECT-TYPE    
  INTEGER normal(0), high(1), interrupting(2)  

gvcIfDlciVcDataPath 1.3.6.1.4.1.562.2.4.1.107.7.3.10.1.32
This attribute indicates the data path used by the connection. The data path is provisioned in Dna and DirectCall components. The displayed value of this attribute can be different from the provisioned value. If the connection is using dprsOnly data path, the string dprsOnly is displayed. (dynamic packet routing system) If the connection is using dprsMcsOnly data path, the string dprsMcsOnly is displayed. If the connection is using dprsMcsFirst data path, the string dprsMcsFirst is displayed.
OBJECT-TYPE    
  AsciiString SIZE(0..32)  

gvcIfDlciVcIntdTable 1.3.6.1.4.1.562.2.4.1.107.7.3.11
This group defines display of interval data collected by Vc. Data in this group is variable and may depend on time when this display command is issued.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciVcIntdEntry

gvcIfDlciVcIntdEntry 1.3.6.1.4.1.562.2.4.1.107.7.3.11.1
An entry in the gvcIfDlciVcIntdTable.
OBJECT-TYPE    
  GvcIfDlciVcIntdEntry  

gvcIfDlciVcCallReferenceNumber 1.3.6.1.4.1.562.2.4.1.107.7.3.11.1.1
This attribute displays the call reference number which is a unique number generated by the switch.The same Call Reference Number is stored in the interval data (accounting record) at both ends of the call. It can be used as one of the attributes in matching duplicate records generated at each end of the call.
OBJECT-TYPE    
  Hex 0..16777215  

gvcIfDlciVcElapsedTimeTillNow 1.3.6.1.4.1.562.2.4.1.107.7.3.11.1.2
This attribute displays the elapsed time representing the period of this interval data. It is elapsed time in 0.1 second increments since Vc started.
OBJECT-TYPE    
  Unsigned32 0..16777215  

gvcIfDlciVcSegmentsRx 1.3.6.1.4.1.562.2.4.1.107.7.3.11.1.3
This attribute displays the number of segments received at the time command was issued. This is the segment received count maintained by accounting at each end of the Vc. This counter is updated only when the packet cannot be successfully delivered out of the sink Vc and to the sink AP Conditions in which packets may be discarded by the sink Vc include: missing packets due to subnet discards, segmentation protocol violations due to subnet discard, duplicated and out-of-ranged packets and packets that arrive while Vc is in path recovery state.
OBJECT-TYPE    
  Unsigned32 0..16777215  

gvcIfDlciVcSegmentsSent 1.3.6.1.4.1.562.2.4.1.107.7.3.11.1.4
This attribute displays the number of segments sent at the time command was issued. This is the segment sent count maintained by accounting at the source Vc. Vc only counts packets that Vc thinks can be delivered successfully into the subnet. In reality, these packets may be dropped by trunking, for instance. This counter is not updated when splitting fails, when Vc is in a path recovery state, when packet forwarding fails to forward this packet and when subsequent packets have to be discarded as we want to minimize the chance of out-of-sequence and do not intentionally send out-of- sequenced packets into the subnet.
OBJECT-TYPE    
  Unsigned32 0..16777215  

gvcIfDlciVcStartTime 1.3.6.1.4.1.562.2.4.1.107.7.3.11.1.5
This attribute displays the start time of this interval period. If Vc spans 12 hour time or time of day change startTime reflects new time as recorded at 12 hour periods or time of day changes.
OBJECT-TYPE    
  EnterpriseDateAndTime SIZE(0 | 19)  

gvcIfDlciVcFrdTable 1.3.6.1.4.1.562.2.4.1.107.7.3.12
This group defines Frame Relay attributes collected by Frame Relay Vc. The purpose of Vc attributes is to aid end users and verification people to understand the Vc internal behavior. This is particularly useful when the network has experienced abnormality and we want to isolate problems and pinpoint trouble spots. Attributes are collected on a per Vc basis. Until a need is identified, statistics are not collected at a processor level. Each attribute is stored in a 32 bit field and is initialized to zero when a Vc enters into the data transfer state. When a PVC is disconnected and then connected again, the attributes will be reset. Attributes cannot be reset through other methods. Frame Relay Vc uses a best effort data packet delivery protocol and a different packet segmentation and combination methods from the General Vc. The Frame Relay Vc uses the same call setup and control mechanism (e.g. the support of non-flow control data packets) as in a General Vc. Most General Vc statistics and internal variables are used in a Frame Relay Vc and are displayed by software developers
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciVcFrdEntry

gvcIfDlciVcFrdEntry 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1
An entry in the gvcIfDlciVcFrdTable.
OBJECT-TYPE    
  GvcIfDlciVcFrdEntry  

gvcIfDlciVcFrmCongestedToSubnet 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.2
This attribute displays the number of frames from link discarded due to lack of resources. It keeps track of the number of frames from link that have to be discarded. The discard reasons include insufficient memory for splitting the frame into smaller subnet packet size.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciVcCannotForwardToSubnet 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.3
This attribute displays the number of discarded packets that can not be forwarded into the subnet because of subnet congestion. Number of frames from link discarded due to failure in forwarding a packet from Vc into the subnet.- This attribute is increased when packet forwarding fails to forward a packet into the subnet. If a frame is split into multiple subnet packets and a partial packet has to be discarded, all subsequent partial packets that have not yet been delivered to the subnet will be discarded as well.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciVcNotDataXferToSubnet 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.4
This attribute records the number of frames from link discarded when the Vc tries to recover from internal path failure.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciVcOutOfRangeFrmFromSubnet 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.5
This attribute displays the number of frames from subnet discarded due to out of sequence range for arriving too late.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciVcCombErrorsFromSubnet 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.6
This attribute records the number of subnet packets discarded at the sink Vc due to the Vc segmentation and combination protocol error. Usually, this occurs when the subnet discards packets and thus this statistics can be used to guest the number of subnet packets that are not delivered to the Vc. It cannot be used as an actual measure because some subnet packets may have been delivered to Vc but have to be discarded because these are partial packets to a frame in which some other partial packets have not been properly delivered to Vc
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciVcDuplicatesFromSubnet 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.7
This attribute displays the number of subnet packets discarded due to duplication. Although packets are not retransmitted by the Frame Relay Vc, it is possible for the subnet to retransmit packets. When packets are out-of-sequenced and copies of the same packets arrive, then this attribute is increased.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciVcNotDataXferFromSubnet 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.8
This attribute displays the number of subnet packets discarded when data transfer is suspended in Vc recovery.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciVcFrmLossTimeouts 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.9
This attribute displays the number of lost frame timer expiries. When this count is excessive, the network is very congested and packets have been discarded in the subnet.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciVcOoSeqByteCntExceeded 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.10
This attribute displays the number times that the out of sequence byte threshold is exceeded. When the threshold is exceeded, this condition is treated as if the loss frame timer has expired and all frames queued at the sink Vc are delivered to the AP. We need to keep this count to examine if the threshold is engineered properly. This should be used in conjunction with the peak value of out-of- sequenced queue and the number of times the loss frame timer has expired. This count should be relatively small when compared with loss frame timer expiry count.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciVcPeakOoSeqPktCount 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.11
This attribute displays the frame relay peak packet count of the out of sequence queue. This attribute records the maximum queue length of the out-of-sequenced queue. The counter can be used to deduce the message buffer requirement on a Vc.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciVcPeakOoSeqFrmForwarded 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.12
This attribute displays the frame relay peak size of the sequence packet queue. The subnet may deliver packets out-of- sequenced. These packets are then queued in an out-of-sequenced queue, waiting for a packet with the expected sequence number to come. When that packet arrives, this attribute records the maximum number of packets that were out-of-sequenced, but now have become in-sequenced. The statistics is used to measure expected queue size due to normal subnet packet disorder (not due to subnet packet discard). Current implementation also uses this statistics to set a maximum size for the out-of-sequenced queue.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciVcSendSequenceNumber 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.13
This attribute displays the Vc internal packet's send sequence number. Note that a 'packet' in this context, may be either a user data packet, or an OAM frame.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciVcPktRetryTimeouts 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.15
This attribute displays the number of packets which have retransmission time-outs. When this count is excessive, the network is very congested and packets have been discarded in the subnet.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciVcPeakRetryQueueSize 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.16
This attribute displays the peak size of retransmission queue. This attribute is used as an indicator of the acknowledgment behavior across the subnet. Records the largest body of unacknowledged packets.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciVcSubnetRecoveries 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.17
This attribute displays the number of successful Vc recovery attempts.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciVcOoSeqPktCntExceeded 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.19
This attribute displays the number times that the out of sequence packet threshold is exceeded. When the threshold is exceeded, this condition is treated as if the loss frame timer has expired and all frames queued at the sink Vc are delivered to the AP. We need to keep this count to examine if the threshold is engineered properly. This should be used in conjunction with the peak value of out-of- sequenced queue and the number of times the loss frame timer has expired. This count should be relatively small when compared with loss frame timer expiry count.
OBJECT-TYPE    
  Unsigned32 0..255  

gvcIfDlciVcPeakOoSeqByteCount 1.3.6.1.4.1.562.2.4.1.107.7.3.12.1.20
This attribute displays the frame relay peak byte count of the out of sequence queue. This attribute records the maximum queue length of the out-of-sequenced queue. The counter can be used to deduce the message buffer requirement on a Vc.
OBJECT-TYPE    
  Unsigned32 0..50000  

gvcIfDlciVcDmepTable 1.3.6.1.4.1.562.2.4.1.107.7.3.417
This attribute displays the data path used by the connection. Data path is provisioned in Dna and DirectCall components. If the connection is using dprsOnly data path, this attribute is empty. If the connection is using dprsMcsOnly or dprsMcsFirst data path, this attribute displays component name of the dprsMcsEndPoint.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciVcDmepEntry

gvcIfDlciVcDmepEntry 1.3.6.1.4.1.562.2.4.1.107.7.3.417.1
An entry in the gvcIfDlciVcDmepTable.
OBJECT-TYPE    
  GvcIfDlciVcDmepEntry  

gvcIfDlciVcDmepValue 1.3.6.1.4.1.562.2.4.1.107.7.3.417.1.1
This variable represents both the value and the index for the gvcIfDlciVcDmepTable.
OBJECT-TYPE    
  RowPointer  

gvcIfDlciSp 1.3.6.1.4.1.562.2.4.1.107.7.4
OBJECT IDENTIFIER    

gvcIfDlciSpRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.7.4.1
This entry controls the addition and deletion of gvcIfDlciSp components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciSpRowStatusEntry

gvcIfDlciSpRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.7.4.1.1
A single entry in the table represents a single gvcIfDlciSp component.
OBJECT-TYPE    
  GvcIfDlciSpRowStatusEntry  

gvcIfDlciSpRowStatus 1.3.6.1.4.1.562.2.4.1.107.7.4.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDlciSp components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDlciSpComponentName 1.3.6.1.4.1.562.2.4.1.107.7.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDlciSpStorageType 1.3.6.1.4.1.562.2.4.1.107.7.4.1.1.4
This variable represents the storage type value for the gvcIfDlciSp tables.
OBJECT-TYPE    
  StorageType  

gvcIfDlciSpIndex 1.3.6.1.4.1.562.2.4.1.107.7.4.1.1.10
This variable represents the index for the gvcIfDlciSp tables.
OBJECT-TYPE    
  NonReplicated  

gvcIfDlciSpParmsTable 1.3.6.1.4.1.562.2.4.1.107.7.4.11
This group contains the provisionable attributes for the Data Link Connection Identifier. These attributes reflect the service parameters specific to this instance of Dlci.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciSpParmsEntry

gvcIfDlciSpParmsEntry 1.3.6.1.4.1.562.2.4.1.107.7.4.11.1
An entry in the gvcIfDlciSpParmsTable.
OBJECT-TYPE    
  GvcIfDlciSpParmsEntry  

gvcIfDlciSpRateEnforcement 1.3.6.1.4.1.562.2.4.1.107.7.4.11.1.1
This attribute specifies whether rate enforcement is to be used on this DLCI. Turning on rate enforcement means that the data sent from the service to the virtual circuit is subjected to rate control.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

gvcIfDlciSpCommittedInformationRate 1.3.6.1.4.1.562.2.4.1.107.7.4.11.1.2
This attribute specifies the committed information rate (cir) in bits per second (bit/s). When rateEnforcement is set to on, cir is the rate at which the network agrees to transfer information under normal conditions. This rate is measured over a measurement interval (t) that is determined internally based on cir and the committed burst size (bc). An exception to this occurs when cir is provisioned to be zero, in which case the measurement interval (t) must be provisioned explicitly. This attribute is ignored when rateEnforcement is off. If rateEnforcement is on and this attribute is 0, bc must also be 0.
OBJECT-TYPE    
  Unsigned32 0..50000000  

gvcIfDlciSpCommittedBurstSize 1.3.6.1.4.1.562.2.4.1.107.7.4.11.1.3
This attribute specifies the committed burst size (bc) in bits. bc is the amount of data that a network agrees to transfer under normal conditions over a measurement interval (t). Data marked DE=1 is not accounted for in bc. This attribute is ignored when rateEnforcement is off. If rateEnforcement is on and this attribute is 0, cir must also be 0.
OBJECT-TYPE    
  Unsigned32 0..50000000  

gvcIfDlciSpExcessBurstSize 1.3.6.1.4.1.562.2.4.1.107.7.4.11.1.4
This attribute specifies the excess burst size (be) in bits. be is the amount of uncommitted data that the network will attempt to deliver over measurement interval (t). Data marked DE=1 by the user or by the network is accounted for here. cir, bc, and be cannot all be 0 when rateEnforcement is on.
OBJECT-TYPE    
  Unsigned32 0..50000000  

gvcIfDlciSpMeasurementInterval 1.3.6.1.4.1.562.2.4.1.107.7.4.11.1.5
This attribute specifies the time interval (in milliseconds) over which rates and burst sizes are measured. When cir and bc are 0 and rateEnforcement is on, this attribute must be provisioned. When cir and bc are non-zero, the time interval is internally calculated. In that situation, this attribute is ignored, and is not representative of the time interval. This attribute is also ignored when rateEnforcement is off. If rateEnforcement is on and both cir and bc are 0, this field must be non-zero.
OBJECT-TYPE    
  Unsigned32 0..25500  

gvcIfDlciBnn 1.3.6.1.4.1.562.2.4.1.107.7.5
OBJECT IDENTIFIER    

gvcIfDlciBnnRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.7.5.1
This entry controls the addition and deletion of gvcIfDlciBnn components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciBnnRowStatusEntry

gvcIfDlciBnnRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.7.5.1.1
A single entry in the table represents a single gvcIfDlciBnn component.
OBJECT-TYPE    
  GvcIfDlciBnnRowStatusEntry  

gvcIfDlciBnnRowStatus 1.3.6.1.4.1.562.2.4.1.107.7.5.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDlciBnn components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDlciBnnComponentName 1.3.6.1.4.1.562.2.4.1.107.7.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDlciBnnStorageType 1.3.6.1.4.1.562.2.4.1.107.7.5.1.1.4
This variable represents the storage type value for the gvcIfDlciBnn tables.
OBJECT-TYPE    
  StorageType  

gvcIfDlciBnnIndex 1.3.6.1.4.1.562.2.4.1.107.7.5.1.1.10
This variable represents the index for the gvcIfDlciBnn tables.
OBJECT-TYPE    
  NonReplicated  

gvcIfDlciLdev 1.3.6.1.4.1.562.2.4.1.107.7.6
OBJECT IDENTIFIER    

gvcIfDlciLdevRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.7.6.1
This entry controls the addition and deletion of gvcIfDlciLdev components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciLdevRowStatusEntry

gvcIfDlciLdevRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.7.6.1.1
A single entry in the table represents a single gvcIfDlciLdev component.
OBJECT-TYPE    
  GvcIfDlciLdevRowStatusEntry  

gvcIfDlciLdevRowStatus 1.3.6.1.4.1.562.2.4.1.107.7.6.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDlciLdev components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDlciLdevComponentName 1.3.6.1.4.1.562.2.4.1.107.7.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDlciLdevStorageType 1.3.6.1.4.1.562.2.4.1.107.7.6.1.1.4
This variable represents the storage type value for the gvcIfDlciLdev tables.
OBJECT-TYPE    
  StorageType  

gvcIfDlciLdevIndex 1.3.6.1.4.1.562.2.4.1.107.7.6.1.1.10
This variable represents the index for the gvcIfDlciLdev tables.
OBJECT-TYPE    
  NonReplicated  

gvcIfDlciLdevAddrTable 1.3.6.1.4.1.562.2.4.1.107.7.6.10
This group defines the LAN MAC address.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciLdevAddrEntry

gvcIfDlciLdevAddrEntry 1.3.6.1.4.1.562.2.4.1.107.7.6.10.1
An entry in the gvcIfDlciLdevAddrTable.
OBJECT-TYPE    
  GvcIfDlciLdevAddrEntry  

gvcIfDlciLdevMac 1.3.6.1.4.1.562.2.4.1.107.7.6.10.1.1
This attribute specifies the MAC of the device located on this side of the PVC, normally the host device. This address is inserted in the Destination Address (DA) field of the 802.5 frames sent typically to a Token Ring interface.
OBJECT-TYPE    
  DashedHexString SIZE(6)  

gvcIfDlciLdevDevOpTable 1.3.6.1.4.1.562.2.4.1.107.7.6.11
This group specifies the operational attributes for devices that are potentially reachable by the SNA DLR service.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciLdevDevOpEntry

gvcIfDlciLdevDevOpEntry 1.3.6.1.4.1.562.2.4.1.107.7.6.11.1
An entry in the gvcIfDlciLdevDevOpTable.
OBJECT-TYPE    
  GvcIfDlciLdevDevOpEntry  

gvcIfDlciLdevDeviceStatus 1.3.6.1.4.1.562.2.4.1.107.7.6.11.1.1
This attribute indicates whether the local device specified by mac is reachable or unreachable from this SNA DLR interface. The device status is determined by the SNA DLR service by sending a TEST frame with the Poll bit set to the device periodically. If a TEST frame with the Final bit set is received from the device then the device status becomes reachable; otherwise the device status is unreachable. When the device status is reachable, connections to this device are accepted. When the device status is unreachable, existing connections to the device are cleared and new connections are cleared to hunt or redirection services.
OBJECT-TYPE    
  INTEGER unreachable(0), reachable(1)  

gvcIfDlciLdevActiveLinkStations 1.3.6.1.4.1.562.2.4.1.107.7.6.11.1.2
This attribute indicates the number of active link station connections using this device mapping component. It includes the link stations using the Qllc and the Frame-Relay connections.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfDlciLdevLastTimeUnreachable 1.3.6.1.4.1.562.2.4.1.107.7.6.11.1.3
This attribute indicates the last time the deviceStatus changed from reachable to unreachable.
OBJECT-TYPE    
  EnterpriseDateAndTime SIZE(0 | 19)  

gvcIfDlciLdevLastTimeReachable 1.3.6.1.4.1.562.2.4.1.107.7.6.11.1.4
This attribute indicates the last time the deviceStatus changed from unreachable to reachable.
OBJECT-TYPE    
  EnterpriseDateAndTime SIZE(0 | 19)  

gvcIfDlciLdevDeviceUnreachable 1.3.6.1.4.1.562.2.4.1.107.7.6.11.1.5
This attribute counts the number of times the deviceStatus changed from reachable to unreachable. When the maximum count is exceeded the count wraps to zero.
OBJECT-TYPE    
  Counter32  

gvcIfDlciLdevMonitoringLcn 1.3.6.1.4.1.562.2.4.1.107.7.6.11.1.6
This attribute indicates the instance of the GvcIf/n Lcn that is reserved for monitoring the device indicated by the mac.
OBJECT-TYPE    
  INTEGER 1..4095  

gvcIfDlciLdevDmoTable 1.3.6.1.4.1.562.2.4.1.107.7.6.12
This group defines the device monitoring options.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciLdevDmoEntry

gvcIfDlciLdevDmoEntry 1.3.6.1.4.1.562.2.4.1.107.7.6.12.1
An entry in the gvcIfDlciLdevDmoTable.
OBJECT-TYPE    
  GvcIfDlciLdevDmoEntry  

gvcIfDlciLdevDeviceMonitoring 1.3.6.1.4.1.562.2.4.1.107.7.6.12.1.1
This attribute specifies wether device monitoring for the device specified in mac is enabled or disabled.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

gvcIfDlciLdevClearVcsWhenUnreachable 1.3.6.1.4.1.562.2.4.1.107.7.6.12.1.2
This attribute specifies wether to clear or not existing VCs when deviceStatus changes from reachable to unreachable.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

gvcIfDlciLdevDeviceMonitoringTimer 1.3.6.1.4.1.562.2.4.1.107.7.6.12.1.3
This attribute specifies the wait period between 2 consecutive device monitoring sequences. A device monitoring sequence is characterized by one of the following: up to maxTestRetry TEST commands sent and a TEST response received or up to maxTestRetry of TEST commands sent and no TEST response received.
OBJECT-TYPE    
  Unsigned32 1..255  

gvcIfDlciLdevTestResponseTimer 1.3.6.1.4.1.562.2.4.1.107.7.6.12.1.4
This attribute specifies the wait period between 2 consecutive TEST commands sent during one device monitoring sequence. A device monitoring sequence is characterized by one of the following: up to maxTestRetry TEST commands sent and a TEST response received or up to maxTestRetry of TEST commands sent and no TEST response received.
OBJECT-TYPE    
  Unsigned32 1..30  

gvcIfDlciLdevMaximumTestRetry 1.3.6.1.4.1.562.2.4.1.107.7.6.12.1.5
This attribute specifies the maximum number of TEST commands sent during one device monitoring sequence. A device monitoring sequence is characterized by one of the following: up to maxTestRetry TEST commands sent and a TEST response received or up to maxTestRetry of TEST commands sent and no TEST response received.
OBJECT-TYPE    
  Unsigned32 1..100  

gvcIfDlciRdev 1.3.6.1.4.1.562.2.4.1.107.7.7
OBJECT IDENTIFIER    

gvcIfDlciRdevRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.7.7.1
This entry controls the addition and deletion of gvcIfDlciRdev components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciRdevRowStatusEntry

gvcIfDlciRdevRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.7.7.1.1
A single entry in the table represents a single gvcIfDlciRdev component.
OBJECT-TYPE    
  GvcIfDlciRdevRowStatusEntry  

gvcIfDlciRdevRowStatus 1.3.6.1.4.1.562.2.4.1.107.7.7.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDlciRdev components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDlciRdevComponentName 1.3.6.1.4.1.562.2.4.1.107.7.7.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDlciRdevStorageType 1.3.6.1.4.1.562.2.4.1.107.7.7.1.1.4
This variable represents the storage type value for the gvcIfDlciRdev tables.
OBJECT-TYPE    
  StorageType  

gvcIfDlciRdevIndex 1.3.6.1.4.1.562.2.4.1.107.7.7.1.1.10
This variable represents the index for the gvcIfDlciRdev tables.
OBJECT-TYPE    
  NonReplicated  

gvcIfDlciRdevAddrTable 1.3.6.1.4.1.562.2.4.1.107.7.7.10
This group defines the LAN MAC address.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciRdevAddrEntry

gvcIfDlciRdevAddrEntry 1.3.6.1.4.1.562.2.4.1.107.7.7.10.1
An entry in the gvcIfDlciRdevAddrTable.
OBJECT-TYPE    
  GvcIfDlciRdevAddrEntry  

gvcIfDlciRdevMac 1.3.6.1.4.1.562.2.4.1.107.7.7.10.1.1
This attribute specifies the MAC address that must be present in the Destination Address (DA) field of the 802.5 frames received (typically from a Token Ring interface) in order for the SNA DLR interface to copy them across this PVC. The MAC address in the frames is not necessarily the real MAC address of the remote device since it could be re-mapped at the remote end of the PVC using the Ddm or Sdm component or the equivalent mapping on another vendor's equipment.
OBJECT-TYPE    
  DashedHexString SIZE(6)  

gvcIfDlciSap 1.3.6.1.4.1.562.2.4.1.107.7.8
OBJECT IDENTIFIER    

gvcIfDlciSapRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.7.8.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of gvcIfDlciSap components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciSapRowStatusEntry

gvcIfDlciSapRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.7.8.1.1
A single entry in the table represents a single gvcIfDlciSap component.
OBJECT-TYPE    
  GvcIfDlciSapRowStatusEntry  

gvcIfDlciSapRowStatus 1.3.6.1.4.1.562.2.4.1.107.7.8.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDlciSap components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDlciSapComponentName 1.3.6.1.4.1.562.2.4.1.107.7.8.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDlciSapStorageType 1.3.6.1.4.1.562.2.4.1.107.7.8.1.1.4
This variable represents the storage type value for the gvcIfDlciSap tables.
OBJECT-TYPE    
  StorageType  

gvcIfDlciSapLocalSapIndex 1.3.6.1.4.1.562.2.4.1.107.7.8.1.1.10
This variable represents an index for the gvcIfDlciSap tables.
OBJECT-TYPE    
  Integer32 4 | 8 | 12 | 16 | 20 | 24 | 28 | 32 | 36 | 40 | 44 | 48 | 52 | 56 | 60 | 64 | 68 | 72 | 76 | 80 | 84 | 88 | 92 | 96 | 100 | 104 | 108 | 112 | 116 | 120 | 124 | 128 | 132 | 136 | 140 | 144 | 148 | 152 | 156 | 160 | 164 | 168 | 172 | 176 | 180 | 184 | 188 | 192 | 196 | 200 | 204 | 208 | 212 | 216 | 220 | 232 | 236 | 248 | 252  

gvcIfDlciSapRemoteSapIndex 1.3.6.1.4.1.562.2.4.1.107.7.8.1.1.11
This variable represents an index for the gvcIfDlciSap tables.
OBJECT-TYPE    
  Integer32 4 | 8 | 12 | 16 | 20 | 24 | 28 | 32 | 36 | 40 | 44 | 48 | 52 | 56 | 60 | 64 | 68 | 72 | 76 | 80 | 84 | 88 | 92 | 96 | 100 | 104 | 108 | 112 | 116 | 120 | 124 | 128 | 132 | 136 | 140 | 144 | 148 | 152 | 156 | 160 | 164 | 168 | 172 | 176 | 180 | 184 | 188 | 192 | 196 | 200 | 204 | 208 | 212 | 216 | 220 | 232 | 236 | 248 | 252  

gvcIfDlciSapCircuit 1.3.6.1.4.1.562.2.4.1.107.7.8.2
OBJECT IDENTIFIER    

gvcIfDlciSapCircuitRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.7.8.2.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of gvcIfDlciSapCircuit components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciSapCircuitRowStatusEntry

gvcIfDlciSapCircuitRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.7.8.2.1.1
A single entry in the table represents a single gvcIfDlciSapCircuit component.
OBJECT-TYPE    
  GvcIfDlciSapCircuitRowStatusEntry  

gvcIfDlciSapCircuitRowStatus 1.3.6.1.4.1.562.2.4.1.107.7.8.2.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDlciSapCircuit components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDlciSapCircuitComponentName 1.3.6.1.4.1.562.2.4.1.107.7.8.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDlciSapCircuitStorageType 1.3.6.1.4.1.562.2.4.1.107.7.8.2.1.1.4
This variable represents the storage type value for the gvcIfDlciSapCircuit tables.
OBJECT-TYPE    
  StorageType  

gvcIfDlciSapCircuitS1MacIndex 1.3.6.1.4.1.562.2.4.1.107.7.8.2.1.1.10
This variable represents an index for the gvcIfDlciSapCircuit tables.
OBJECT-TYPE    
  DashedHexString SIZE(6)  

gvcIfDlciSapCircuitS1SapIndex 1.3.6.1.4.1.562.2.4.1.107.7.8.2.1.1.11
This variable represents an index for the gvcIfDlciSapCircuit tables.
OBJECT-TYPE    
  Integer32 2..254  

gvcIfDlciSapCircuitS2MacIndex 1.3.6.1.4.1.562.2.4.1.107.7.8.2.1.1.12
This variable represents an index for the gvcIfDlciSapCircuit tables.
OBJECT-TYPE    
  DashedHexString SIZE(6)  

gvcIfDlciSapCircuitS2SapIndex 1.3.6.1.4.1.562.2.4.1.107.7.8.2.1.1.13
This variable represents an index for the gvcIfDlciSapCircuit tables.
OBJECT-TYPE    
  Integer32 2..254  

gvcIfDlciStateTable 1.3.6.1.4.1.562.2.4.1.107.7.10
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciStateEntry

gvcIfDlciStateEntry 1.3.6.1.4.1.562.2.4.1.107.7.10.1
An entry in the gvcIfDlciStateTable.
OBJECT-TYPE    
  GvcIfDlciStateEntry  

gvcIfDlciAdminState 1.3.6.1.4.1.562.2.4.1.107.7.10.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

gvcIfDlciOperationalState 1.3.6.1.4.1.562.2.4.1.107.7.10.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

gvcIfDlciUsageState 1.3.6.1.4.1.562.2.4.1.107.7.10.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

gvcIfDlciAbitTable 1.3.6.1.4.1.562.2.4.1.107.7.11
This group contains the A-Bit status information for this Data Link Connection Identifier. A-Bit status information is only applicable for PVCs. For SVCs, the values of attributes under this group are all notApplicable.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciAbitEntry

gvcIfDlciAbitEntry 1.3.6.1.4.1.562.2.4.1.107.7.11.1
An entry in the gvcIfDlciAbitTable.
OBJECT-TYPE    
  GvcIfDlciAbitEntry  

gvcIfDlciABitStatusFromNetwork 1.3.6.1.4.1.562.2.4.1.107.7.11.1.1
This attribute indicates the most recent A-bit status received from the subnet. The A-bit status is part of the LMI protocol. It indicates willingness to accept data from the Protocol Port associated with this GvcIf. When an inactive status is sent out, the Frame Relay service discards any data offered from the Protocol Port. When an active status is sent out, the Frame Relay service tries to process all data offered from the Protocol Port.
OBJECT-TYPE    
  INTEGER inactive(0), active(1), notApplicable(2)  

gvcIfDlciABitReasonFromNetwork 1.3.6.1.4.1.562.2.4.1.107.7.11.1.2
This attribute indicates the reason (if any) for an inactive status to be sent to the Protocol Port associated with this GvcIf. This reason is notapplicable for an active status.
OBJECT-TYPE    
  INTEGER notApplicable(0), remoteUserSignaled(1), localLmiError(2), remoteLmiError(3), localLinkDown(4), remoteLinkDown(5), pvcDown(6)  

gvcIfDlciABitStatusToNetwork 1.3.6.1.4.1.562.2.4.1.107.7.11.1.3
This attribute indicates the most recent A-Bit status sent from this GvcIf to the subnet.
OBJECT-TYPE    
  INTEGER inactive(0), active(1), notApplicable(2)  

gvcIfDlciABitReasonToNetwork 1.3.6.1.4.1.562.2.4.1.107.7.11.1.4
This attribute indicates the reason (if any) for an inactive status to be sent to the subnet from this GvcIf. This reason is not applicable for an active status.
OBJECT-TYPE    
  INTEGER notApplicable(0), remoteUserSignaled(1), localLmiError(2), localLinkDown(4), missingFromLmiReport(7)  

gvcIfDlciStatsTable 1.3.6.1.4.1.562.2.4.1.107.7.12
This group contains the operational statistics for the DLCI.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciStatsEntry

gvcIfDlciStatsEntry 1.3.6.1.4.1.562.2.4.1.107.7.12.1
An entry in the gvcIfDlciStatsTable.
OBJECT-TYPE    
  GvcIfDlciStatsEntry  

gvcIfDlciFrmFromNetwork 1.3.6.1.4.1.562.2.4.1.107.7.12.1.1
This attribute counts the frames received from the subnet and sent to the Protocol Port associated with this GvcIf. When the maximum count is exceeded the count wraps to zero.
OBJECT-TYPE    
  Counter32  

gvcIfDlciFrmToNetwork 1.3.6.1.4.1.562.2.4.1.107.7.12.1.2
This attribute counts the frames sent to the subnet. When the maximum count is exceeded the count wraps to zero.
OBJECT-TYPE    
  Counter32  

gvcIfDlciFrmDiscardToNetwork 1.3.6.1.4.1.562.2.4.1.107.7.12.1.3
This attribute counts the frames which were received from the Protocol Port and discarded due to the aBitStatusFromNetwork being in an inactive state. When this count exceeds the maximum, it wraps to zero.
OBJECT-TYPE    
  Counter32  

gvcIfDlciFramesWithUnknownSaps 1.3.6.1.4.1.562.2.4.1.107.7.12.1.4
This attribute counts the number of frames received from the subnet on a BNN DLCI VC containing an (lSap,rSap) pair that does not match any SapMapping component index.
OBJECT-TYPE    
  Counter32  

gvcIfDlciOperTable 1.3.6.1.4.1.562.2.4.1.107.7.13
This group contains the Dlci operational attributes.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciOperEntry

gvcIfDlciOperEntry 1.3.6.1.4.1.562.2.4.1.107.7.13.1
An entry in the gvcIfDlciOperTable.
OBJECT-TYPE    
  GvcIfDlciOperEntry  

gvcIfDlciEncapsulationType 1.3.6.1.4.1.562.2.4.1.107.7.13.1.1
This attribute indicates the encapsulation type used on this Dlci. ban indicates that SNA frames exchanged on the VC are encapsulated in RFC 1490 BAN format. ban indicates that SNA frames exchanged on the VC are encapsulated in RFC 1490 BNN format.
OBJECT-TYPE    
  INTEGER ban(0), bnn(1)  

gvcIfDlciLocalDeviceMac 1.3.6.1.4.1.562.2.4.1.107.7.13.1.2
This attribute indicates the MAC of the device located on this side of the VC, normally the host device. This address is inserted in the Destination Address (DA) field of the 802.5 frames sent, typically to a Token Ring interface. This address is expected in the SA field of the frames received from the local LAN. When this attribute is not empty All Route Explorer (ARE) and Single Route Explorer (SRE) frames received from the local LAN must have the SA field matching it, otherwise they are discarded.
OBJECT-TYPE    
  DashedHexString SIZE(6)  

gvcIfDlciRemoteDeviceMac 1.3.6.1.4.1.562.2.4.1.107.7.13.1.3
This attribute indicates the MAC of the device located at the far end of the VC. This is normally the host device. This address is inserted in the source address (SA) field of the 802.5 frames sent typically on a token ring interface. This address is expected in the destination address (DA) field of the 802.5 frames received, typically from a token ring interface. When this attribute is defined All Route Explorer (ARE) and Single Route Explorer (SRE) frames received from the local LAN must have the DA field matching it, otherwise they are discarded.
OBJECT-TYPE    
  DashedHexString SIZE(6)  

gvcIfDlciSpOpTable 1.3.6.1.4.1.562.2.4.1.107.7.14
This group contains the actual service parameters in use for this instance of Dlci.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDlciSpOpEntry

gvcIfDlciSpOpEntry 1.3.6.1.4.1.562.2.4.1.107.7.14.1
An entry in the gvcIfDlciSpOpTable.
OBJECT-TYPE    
  GvcIfDlciSpOpEntry  

gvcIfDlciRateEnforcement 1.3.6.1.4.1.562.2.4.1.107.7.14.1.1
This attribute indicates whether rate enforcement is in use for this Dlci.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

gvcIfDlciCommittedInformationRate 1.3.6.1.4.1.562.2.4.1.107.7.14.1.2
This attribute indicates the current effective committed information rate (cir) in bits per second (bit/s). cir is the rate at which the network agrees to transfer data with Discard Eligiblity indication DE=0 under normal conditions. This attribute should be ignored when rateEnforcement is off.
OBJECT-TYPE    
  Gauge32 0..4294967295  

gvcIfDlciCommittedBurstSize 1.3.6.1.4.1.562.2.4.1.107.7.14.1.3
This attribute indicates the committed burst size (bc) in bits. bc is the amount of data that the network agrees to transfer under normal conditions over a measurement interval (t). bc is used for data with Discard Eligibility indication DE=0. DE=1 data does not use bc at all, excessBurstSize if is used instead. This attribute should be ignored when rateEnforcement is off.
OBJECT-TYPE    
  Gauge32 0..4294967295  

gvcIfDlciExcessInformationRate 1.3.6.1.4.1.562.2.4.1.107.7.14.1.4
This attribute indicates the current effective excess information rate (eir) in bits per second (bit/s). eir is the rate at which the network agrees to transfer data with Discard Eligibility indication DE=1 under normal conditions. DE can be set by the user or the network. DE indication of a data frame is set to 1 by the network after cir has been exceeded while eir is still available for data transfer.
OBJECT-TYPE    
  Gauge32 0..4294967295  

gvcIfDlciExcessBurstSize 1.3.6.1.4.1.562.2.4.1.107.7.14.1.5
This attribute indicates the excess burst size (be) in bits. be is the amount of uncommitted data that the network will attempt to deliver over measurement interval (t). Data marked DE=1 by the user or by the network is accounted for here. This attribute should be ignored when rateEnforcement is off.
OBJECT-TYPE    
  Gauge32 0..2048000  

gvcIfDlciMeasurementInterval 1.3.6.1.4.1.562.2.4.1.107.7.14.1.6
This attribute indicates the time interval (in milliseconds) over which rates and burst sizes are measured. This attribute should be ignored when rateEnforcement is off.
OBJECT-TYPE    
  Gauge32 0..25500  

gvcIfFrSvc 1.3.6.1.4.1.562.2.4.1.107.8
OBJECT IDENTIFIER    

gvcIfFrSvcRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.8.1
This entry controls the addition and deletion of gvcIfFrSvc components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfFrSvcRowStatusEntry

gvcIfFrSvcRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.8.1.1
A single entry in the table represents a single gvcIfFrSvc component.
OBJECT-TYPE    
  GvcIfFrSvcRowStatusEntry  

gvcIfFrSvcRowStatus 1.3.6.1.4.1.562.2.4.1.107.8.1.1.1
This variable is used as the basis for SNMP naming of gvcIfFrSvc components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfFrSvcComponentName 1.3.6.1.4.1.562.2.4.1.107.8.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfFrSvcStorageType 1.3.6.1.4.1.562.2.4.1.107.8.1.1.4
This variable represents the storage type value for the gvcIfFrSvc tables.
OBJECT-TYPE    
  StorageType  

gvcIfFrSvcIndex 1.3.6.1.4.1.562.2.4.1.107.8.1.1.10
This variable represents the index for the gvcIfFrSvc tables.
OBJECT-TYPE    
  NonReplicated  

gvcIfFrSvcProvisionedTable 1.3.6.1.4.1.562.2.4.1.107.8.11
This group contains the provisonable parameters for the APPN service Frame Relay SVC calls.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfFrSvcProvisionedEntry

gvcIfFrSvcProvisionedEntry 1.3.6.1.4.1.562.2.4.1.107.8.11.1
An entry in the gvcIfFrSvcProvisionedTable.
OBJECT-TYPE    
  GvcIfFrSvcProvisionedEntry  

gvcIfFrSvcMaximumFrameRelaySvcs 1.3.6.1.4.1.562.2.4.1.107.8.11.1.1
This attribute specifies the maximum number of concurrently active Frame Relay SVC calls that are allowed for this service. This attribute does not include the general switched virtual circuits (GSVC).
OBJECT-TYPE    
  Unsigned32 1..3072  

gvcIfFrSvcRateEnforcement 1.3.6.1.4.1.562.2.4.1.107.8.11.1.2
This attribute specifies whether rate enforcement is to be used for new Frame Relay SVCs on this service. When rate enforcement is on the rate of data sent by the service to individual Frame Relay SVCs is controlled.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

gvcIfFrSvcMaximumCir 1.3.6.1.4.1.562.2.4.1.107.8.11.1.4
This attribute specifies the maximum rate enforcement CIR (Committed Information Rate) that is allowed for use with the Frame Relay SVCs on this service. During call setup negotiation, if the caller to this service requests a higher CIR value be used, the CIR used is reduced to the value of maximumCir.
OBJECT-TYPE    
  Unsigned32 0..52000000  

gvcIfFrSvcOperationalTable 1.3.6.1.4.1.562.2.4.1.107.8.12
This group contains the operational attributes for the APPN Frame Relay SVC calls.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfFrSvcOperationalEntry

gvcIfFrSvcOperationalEntry 1.3.6.1.4.1.562.2.4.1.107.8.12.1
An entry in the gvcIfFrSvcOperationalTable.
OBJECT-TYPE    
  GvcIfFrSvcOperationalEntry  

gvcIfFrSvcCurrentNumberOfSvcCalls 1.3.6.1.4.1.562.2.4.1.107.8.12.1.1
This attribute indicates the number of Frame Relay SVCs currently existing on this service. This attribute does not include the general switched virtual circuits (GSVC).
OBJECT-TYPE    
  Gauge32 0..3072  

gvcIfSMacF 1.3.6.1.4.1.562.2.4.1.107.9
OBJECT IDENTIFIER    

gvcIfSMacFRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.9.1
This entry controls the addition and deletion of gvcIfSMacF components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfSMacFRowStatusEntry

gvcIfSMacFRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.9.1.1
A single entry in the table represents a single gvcIfSMacF component.
OBJECT-TYPE    
  GvcIfSMacFRowStatusEntry  

gvcIfSMacFRowStatus 1.3.6.1.4.1.562.2.4.1.107.9.1.1.1
This variable is used as the basis for SNMP naming of gvcIfSMacF components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfSMacFComponentName 1.3.6.1.4.1.562.2.4.1.107.9.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfSMacFStorageType 1.3.6.1.4.1.562.2.4.1.107.9.1.1.4
This variable represents the storage type value for the gvcIfSMacF tables.
OBJECT-TYPE    
  StorageType  

gvcIfSMacFIndex 1.3.6.1.4.1.562.2.4.1.107.9.1.1.10
This variable represents the index for the gvcIfSMacF tables.
OBJECT-TYPE    
  DashedHexString SIZE(6)  

gvcIfSMacFOperTable 1.3.6.1.4.1.562.2.4.1.107.9.11
This group provides the administrative set of parameters for the GvcIf component.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfSMacFOperEntry

gvcIfSMacFOperEntry 1.3.6.1.4.1.562.2.4.1.107.9.11.1
An entry in the gvcIfSMacFOperTable.
OBJECT-TYPE    
  GvcIfSMacFOperEntry  

gvcIfSMacFFramesMatchingFilter 1.3.6.1.4.1.562.2.4.1.107.9.11.1.1
This attribute counts the number of frames containing a MAC address matching the instance of this component. When the maximum count is exceeded the count wraps to zero.
OBJECT-TYPE    
  Counter32  

gvcIfDMacF 1.3.6.1.4.1.562.2.4.1.107.10
OBJECT IDENTIFIER    

gvcIfDMacFRowStatusTable 1.3.6.1.4.1.562.2.4.1.107.10.1
This entry controls the addition and deletion of gvcIfDMacF components.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDMacFRowStatusEntry

gvcIfDMacFRowStatusEntry 1.3.6.1.4.1.562.2.4.1.107.10.1.1
A single entry in the table represents a single gvcIfDMacF component.
OBJECT-TYPE    
  GvcIfDMacFRowStatusEntry  

gvcIfDMacFRowStatus 1.3.6.1.4.1.562.2.4.1.107.10.1.1.1
This variable is used as the basis for SNMP naming of gvcIfDMacF components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

gvcIfDMacFComponentName 1.3.6.1.4.1.562.2.4.1.107.10.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

gvcIfDMacFStorageType 1.3.6.1.4.1.562.2.4.1.107.10.1.1.4
This variable represents the storage type value for the gvcIfDMacF tables.
OBJECT-TYPE    
  StorageType  

gvcIfDMacFIndex 1.3.6.1.4.1.562.2.4.1.107.10.1.1.10
This variable represents the index for the gvcIfDMacF tables.
OBJECT-TYPE    
  DashedHexString SIZE(6)  

gvcIfDMacFOperTable 1.3.6.1.4.1.562.2.4.1.107.10.11
This group provides the administrative set of parameters for the GvcIf component.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfDMacFOperEntry

gvcIfDMacFOperEntry 1.3.6.1.4.1.562.2.4.1.107.10.11.1
An entry in the gvcIfDMacFOperTable.
OBJECT-TYPE    
  GvcIfDMacFOperEntry  

gvcIfDMacFFramesMatchingFilter 1.3.6.1.4.1.562.2.4.1.107.10.11.1.1
This attribute counts the number of frames containing a MAC address matching the instance of this component. When the maximum count is exceeded the count wraps to zero.
OBJECT-TYPE    
  Counter32  

gvcIfCidDataTable 1.3.6.1.4.1.562.2.4.1.107.30
This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfCidDataEntry

gvcIfCidDataEntry 1.3.6.1.4.1.562.2.4.1.107.30.1
An entry in the gvcIfCidDataTable.
OBJECT-TYPE    
  GvcIfCidDataEntry  

gvcIfCustomerIdentifier 1.3.6.1.4.1.562.2.4.1.107.30.1.1
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
OBJECT-TYPE    
  Unsigned32 0 | 1..8191  

gvcIfProvTable 1.3.6.1.4.1.562.2.4.1.107.31
This group provides the administrative set of parameters for the GvcIf component.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfProvEntry

gvcIfProvEntry 1.3.6.1.4.1.562.2.4.1.107.31.1
An entry in the gvcIfProvTable.
OBJECT-TYPE    
  GvcIfProvEntry  

gvcIfLogicalProcessor 1.3.6.1.4.1.562.2.4.1.107.31.1.1
This attribute specifies the logical processor on which the General VC Interface service is running.
OBJECT-TYPE    
  Link  

gvcIfMaxActiveLinkStation 1.3.6.1.4.1.562.2.4.1.107.31.1.3
This attribute specifies the total number of link station connections that can be active on this service instance. In total maxActiveLinkStation determines the maximum number of Lcn components which may exist at a given time. Once this number is reached no calls will be initiated or accepted by this service instance.
OBJECT-TYPE    
  Unsigned32 1..5000  

gvcIfStateTable 1.3.6.1.4.1.562.2.4.1.107.32
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfStateEntry

gvcIfStateEntry 1.3.6.1.4.1.562.2.4.1.107.32.1
An entry in the gvcIfStateTable.
OBJECT-TYPE    
  GvcIfStateEntry  

gvcIfAdminState 1.3.6.1.4.1.562.2.4.1.107.32.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

gvcIfOperationalState 1.3.6.1.4.1.562.2.4.1.107.32.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

gvcIfUsageState 1.3.6.1.4.1.562.2.4.1.107.32.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

gvcIfOpTable 1.3.6.1.4.1.562.2.4.1.107.33
This group contains the operational attributes of the GvcIf component.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfOpEntry

gvcIfOpEntry 1.3.6.1.4.1.562.2.4.1.107.33.1
An entry in the gvcIfOpTable.
OBJECT-TYPE    
  GvcIfOpEntry  

gvcIfActiveLinkStations 1.3.6.1.4.1.562.2.4.1.107.33.1.2
This attribute indicates the number of active link station connections on this service instance at the time of the query. It includes the link stations using the Qllc, the Frame-Relay BAN and the Frame-Relay BNN connections.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfIssueLcnClearAlarm 1.3.6.1.4.1.562.2.4.1.107.33.1.5
This attribute indicates whether alarm issuing is allowed or disallowed whenever an Lcn is cleared. Alarm issuing should be allowed only for monitoring problems.
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

gvcIfActiveQllcCalls 1.3.6.1.4.1.562.2.4.1.107.33.1.6
This attribute indicates the number of active Qllc calls on this service instance at the time of the query. It includes incoming and outgoing calls.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfStatsTable 1.3.6.1.4.1.562.2.4.1.107.34
This group contains the statistics for the GvcIf component.
OBJECT-TYPE    
  SEQUENCE OF  
    GvcIfStatsEntry

gvcIfStatsEntry 1.3.6.1.4.1.562.2.4.1.107.34.1
An entry in the gvcIfStatsTable.
OBJECT-TYPE    
  GvcIfStatsEntry  

gvcIfCallsToNetwork 1.3.6.1.4.1.562.2.4.1.107.34.1.1
This attribute counts the number of Qllc and Frame-Relay calls initiated by this interface into the subnet, including successful and failed calls. When the maximum count is exceeded the count wraps to zero.
OBJECT-TYPE    
  Counter32  

gvcIfCallsFromNetwork 1.3.6.1.4.1.562.2.4.1.107.34.1.2
This attribute counts the number of Qllc and Frame-Relay calls received from the subnet by this interface, including successful and failed calls. When the maximum count is exceeded the count wraps to zero.
OBJECT-TYPE    
  Counter32  

gvcIfCallsRefusedByNetwork 1.3.6.1.4.1.562.2.4.1.107.34.1.3
This attribute counts the number of outgoing Qllc and Frame-Relay calls refused by the subnetwork. When the maximum count is exceeded the count wraps to zero.
OBJECT-TYPE    
  Counter32  

gvcIfCallsRefusedByInterface 1.3.6.1.4.1.562.2.4.1.107.34.1.4
This attribute counts the number of incoming Qllc and Frame-Relay calls refused by the interface. When the maximum count is exceeded the count wraps to zero.
OBJECT-TYPE    
  Counter32  

gvcIfPeakActiveLinkStations 1.3.6.1.4.1.562.2.4.1.107.34.1.6
This attribute indicates the maximum value of concurrently active link station connections since the service became active.
OBJECT-TYPE    
  Unsigned32 0..5000  

gvcIfBcastFramesDiscarded 1.3.6.1.4.1.562.2.4.1.107.34.1.7
This attribute counts the number of broadcast frames that have been discarded because they do not meet one of the following criterias: - the source MAC address does not match the instance of at least one SourceMACFilter component, - the destination MAC address does not match the instance of at least one DestinationMACFilter component. When the maximum count is exceeded the count wraps to zero.
OBJECT-TYPE    
  Counter32  

gvcIfDiscardedQllcCalls 1.3.6.1.4.1.562.2.4.1.107.34.1.8
This attribute indicates the number of Qllc calls that are discarded because the maxActiveLinkStation threshold is exceeded. When the maximum count is exceeded the count wraps to zero.
OBJECT-TYPE    
  Counter32  

generalVcInterfaceMIB 1.3.6.1.4.1.562.2.4.2.58
OBJECT IDENTIFIER    

generalVcInterfaceGroup 1.3.6.1.4.1.562.2.4.2.58.1
OBJECT IDENTIFIER    

generalVcInterfaceGroupBE 1.3.6.1.4.1.562.2.4.2.58.1.5
OBJECT IDENTIFIER    

generalVcInterfaceGroupBE01 1.3.6.1.4.1.562.2.4.2.58.1.5.2
OBJECT IDENTIFIER    

generalVcInterfaceGroupBE01A 1.3.6.1.4.1.562.2.4.2.58.1.5.2.2
OBJECT IDENTIFIER    

generalVcInterfaceCapabilities 1.3.6.1.4.1.562.2.4.2.58.3
OBJECT IDENTIFIER    

generalVcInterfaceCapabilitiesBE 1.3.6.1.4.1.562.2.4.2.58.3.5
OBJECT IDENTIFIER    

generalVcInterfaceCapabilitiesBE01 1.3.6.1.4.1.562.2.4.2.58.3.5.2
OBJECT IDENTIFIER    

generalVcInterfaceCapabilitiesBE01A 1.3.6.1.4.1.562.2.4.2.58.3.5.2.2
OBJECT IDENTIFIER    

Defined Objects

GvcIfRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfRowStatus  
  DisplayString as gvcIfComponentName  
  StorageType as gvcIfStorageType  
  Integer32 as gvcIfIndex  

GvcIfCidDataEntry  
SEQUENCE    
  Unsigned32 as gvcIfCustomerIdentifier  

GvcIfProvEntry  
SEQUENCE    
  Link as gvcIfLogicalProcessor  
  Unsigned32 as gvcIfMaxActiveLinkStation  

GvcIfStateEntry  
SEQUENCE    
  INTEGER as gvcIfAdminState  
  INTEGER as gvcIfOperationalState  
  INTEGER as gvcIfUsageState  

GvcIfOpEntry  
SEQUENCE    
  Unsigned32 as gvcIfActiveLinkStations  
  INTEGER as gvcIfIssueLcnClearAlarm  
  Unsigned32 as gvcIfActiveQllcCalls  

GvcIfStatsEntry  
SEQUENCE    
  Counter32 as gvcIfCallsToNetwork  
  Counter32 as gvcIfCallsFromNetwork  
  Counter32 as gvcIfCallsRefusedByNetwork  
  Counter32 as gvcIfCallsRefusedByInterface  
  Unsigned32 as gvcIfPeakActiveLinkStations  
  Counter32 as gvcIfBcastFramesDiscarded  
  Counter32 as gvcIfDiscardedQllcCalls  

GvcIfDcRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDcRowStatus  
  DisplayString as gvcIfDcComponentName  
  StorageType as gvcIfDcStorageType  
  DashedHexString as gvcIfDcMacIndex  
  Integer32 as gvcIfDcSapIndex  

GvcIfDcOptionsEntry  
SEQUENCE    
  INTEGER as gvcIfDcRemoteNpi  
  DigitString as gvcIfDcRemoteDna  
  HexString as gvcIfDcUserData  
  INTEGER as gvcIfDcTransferPriority  
  INTEGER as gvcIfDcDiscardPriority  

GvcIfDcCfaEntry  
SEQUENCE    
  Integer32 as gvcIfDcCfaIndex  
  HexString as gvcIfDcCfaValue  
  RowStatus as gvcIfDcCfaRowStatus  

GvcIfRDnaMapRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfRDnaMapRowStatus  
  DisplayString as gvcIfRDnaMapComponentName  
  StorageType as gvcIfRDnaMapStorageType  
  INTEGER as gvcIfRDnaMapNpiIndex  
  DigitString as gvcIfRDnaMapDnaIndex  

GvcIfRDnaMapLanAdEntry  
SEQUENCE    
  DashedHexString as gvcIfRDnaMapMac  
  Hex as gvcIfRDnaMapSap  

GvcIfLcnRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfLcnRowStatus  
  DisplayString as gvcIfLcnComponentName  
  StorageType as gvcIfLcnStorageType  
  Integer32 as gvcIfLcnIndex  

GvcIfLcnStateEntry  
SEQUENCE    
  INTEGER as gvcIfLcnAdminState  
  INTEGER as gvcIfLcnOperationalState  
  INTEGER as gvcIfLcnUsageState  

GvcIfLcnLcnCIdEntry  
SEQUENCE    
  RowPointer as gvcIfLcnCircuitId  

GvcIfLcnOperEntry  
SEQUENCE    
  INTEGER as gvcIfLcnState  
  RowPointer as gvcIfLcnDnaMap  
  DashedHexString as gvcIfLcnSourceMac  

GvcIfLcnVcRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfLcnVcRowStatus  
  DisplayString as gvcIfLcnVcComponentName  
  StorageType as gvcIfLcnVcStorageType  
  NonReplicated as gvcIfLcnVcIndex  

GvcIfLcnVcCadEntry  
SEQUENCE    
  INTEGER as gvcIfLcnVcType  
  INTEGER as gvcIfLcnVcState  
  INTEGER as gvcIfLcnVcPreviousState  
  Unsigned32 as gvcIfLcnVcDiagnosticCode  
  Unsigned32 as gvcIfLcnVcPreviousDiagnosticCode  
  INTEGER as gvcIfLcnVcCalledNpi  
  DigitString as gvcIfLcnVcCalledDna  
  Unsigned32 as gvcIfLcnVcCalledLcn  
  INTEGER as gvcIfLcnVcCallingNpi  
  DigitString as gvcIfLcnVcCallingDna  
  Unsigned32 as gvcIfLcnVcCallingLcn  
  INTEGER as gvcIfLcnVcAccountingEnabled  
  INTEGER as gvcIfLcnVcFastSelectCall  
  INTEGER as gvcIfLcnVcLocalRxPktSize  
  INTEGER as gvcIfLcnVcLocalTxPktSize  
  Unsigned32 as gvcIfLcnVcLocalTxWindowSize  
  Unsigned32 as gvcIfLcnVcLocalRxWindowSize  
  INTEGER as gvcIfLcnVcPathReliability  
  INTEGER as gvcIfLcnVcAccountingEnd  
  INTEGER as gvcIfLcnVcPriority  
  Unsigned32 as gvcIfLcnVcSegmentSize  
  INTEGER as gvcIfLcnVcSubnetTxPktSize  
  Unsigned32 as gvcIfLcnVcSubnetTxWindowSize  
  INTEGER as gvcIfLcnVcSubnetRxPktSize  
  Unsigned32 as gvcIfLcnVcSubnetRxWindowSize  
  Unsigned32 as gvcIfLcnVcMaxSubnetPktSize  
  INTEGER as gvcIfLcnVcTransferPriorityToNetwork  
  INTEGER as gvcIfLcnVcTransferPriorityFromNetwork  

GvcIfLcnVcIntdEntry  
SEQUENCE    
  Hex as gvcIfLcnVcCallReferenceNumber  
  Unsigned32 as gvcIfLcnVcElapsedTimeTillNow  
  Unsigned32 as gvcIfLcnVcSegmentsRx  
  Unsigned32 as gvcIfLcnVcSegmentsSent  
  EnterpriseDateAndTime as gvcIfLcnVcStartTime  

GvcIfLcnVcStatsEntry  
SEQUENCE    
  Unsigned32 as gvcIfLcnVcAckStackingTimeouts  
  Unsigned32 as gvcIfLcnVcOutOfRangeFrmFromSubnet  
  Unsigned32 as gvcIfLcnVcDuplicatesFromSubnet  
  Unsigned32 as gvcIfLcnVcFrmRetryTimeouts  
  Unsigned32 as gvcIfLcnVcPeakRetryQueueSize  
  Unsigned32 as gvcIfLcnVcPeakOoSeqQueueSize  
  Unsigned32 as gvcIfLcnVcPeakOoSeqFrmForwarded  
  Unsigned32 as gvcIfLcnVcPeakStackedAcksRx  
  Unsigned32 as gvcIfLcnVcSubnetRecoveries  
  Unsigned32 as gvcIfLcnVcWindowClosuresToSubnet  
  Unsigned32 as gvcIfLcnVcWindowClosuresFromSubnet  
  Unsigned32 as gvcIfLcnVcWrTriggers  

GvcIfDnaRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDnaRowStatus  
  DisplayString as gvcIfDnaComponentName  
  StorageType as gvcIfDnaStorageType  
  Integer32 as gvcIfDnaIndex  

GvcIfDnaAddrEntry  
SEQUENCE    
  INTEGER as gvcIfDnaNumberingPlanIndicator  
  DigitString as gvcIfDnaDataNetworkAddress  

GvcIfDnaOutgoingOptionsEntry  
SEQUENCE    
  INTEGER as gvcIfDnaOutDefaultPriority  
  INTEGER as gvcIfDnaOutDefaultPathSensitivity  
  INTEGER as gvcIfDnaOutDefaultPathReliability  
  INTEGER as gvcIfDnaOutAccess  
  INTEGER as gvcIfDnaDefaultTransferPriority  
  INTEGER as gvcIfDnaTransferPriorityOverRide  

GvcIfDnaIncomingOptionsEntry  
SEQUENCE    
  INTEGER as gvcIfDnaIncCalls  
  INTEGER as gvcIfDnaIncHighPriorityReverseCharge  
  INTEGER as gvcIfDnaIncNormalPriorityReverseCharge  
  INTEGER as gvcIfDnaIncIntlNormalCharge  
  INTEGER as gvcIfDnaIncIntlReverseCharge  
  INTEGER as gvcIfDnaIncSameService  
  INTEGER as gvcIfDnaIncAccess  

GvcIfDnaCallOptionsEntry  
SEQUENCE    
  INTEGER as gvcIfDnaServiceCategory  
  OCTET STRING as gvcIfDnaPacketSizes  
  INTEGER as gvcIfDnaDefaultRecvFrmNetworkPacketSize  
  INTEGER as gvcIfDnaDefaultSendToNetworkPacketSize  
  Unsigned32 as gvcIfDnaDefaultRecvFrmNetworkThruputClass  
  Unsigned32 as gvcIfDnaDefaultSendToNetworkThruputClass  
  Unsigned32 as gvcIfDnaDefaultRecvFrmNetworkWindowSize  
  Unsigned32 as gvcIfDnaDefaultSendToNetworkWindowSize  
  INTEGER as gvcIfDnaPacketSizeNegotiation  
  INTEGER as gvcIfDnaCugFormat  
  Unsigned32 as gvcIfDnaAccountClass  
  OCTET STRING as gvcIfDnaAccountCollection  
  Unsigned32 as gvcIfDnaServiceExchange  

GvcIfDnaCugRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDnaCugRowStatus  
  DisplayString as gvcIfDnaCugComponentName  
  StorageType as gvcIfDnaCugStorageType  
  Integer32 as gvcIfDnaCugIndex  

GvcIfDnaCugCugOptionsEntry  
SEQUENCE    
  INTEGER as gvcIfDnaCugType  
  DigitString as gvcIfDnaCugDnic  
  Unsigned32 as gvcIfDnaCugInterlockCode  
  INTEGER as gvcIfDnaCugPreferential  
  INTEGER as gvcIfDnaCugOutCalls  
  INTEGER as gvcIfDnaCugIncCalls  
  INTEGER as gvcIfDnaCugPrivileged  

GvcIfDnaHgMRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDnaHgMRowStatus  
  DisplayString as gvcIfDnaHgMComponentName  
  StorageType as gvcIfDnaHgMStorageType  
  NonReplicated as gvcIfDnaHgMIndex  

GvcIfDnaHgMIfEntry  
SEQUENCE    
  Unsigned32 as gvcIfDnaHgMAvailabilityUpdateThreshold  

GvcIfDnaHgMOpEntry  
SEQUENCE    
  INTEGER as gvcIfDnaHgMAvailabilityDelta  
  Unsigned32 as gvcIfDnaHgMMaxAvailableLinkStations  
  Unsigned32 as gvcIfDnaHgMAvailableLinkStations  

GvcIfDnaHgMHgAddrRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDnaHgMHgAddrRowStatus  
  DisplayString as gvcIfDnaHgMHgAddrComponentName  
  StorageType as gvcIfDnaHgMHgAddrStorageType  
  Integer32 as gvcIfDnaHgMHgAddrIndex  

GvcIfDnaHgMHgAddrAddrEntry  
SEQUENCE    
  INTEGER as gvcIfDnaHgMHgAddrNumberingPlanIndicator  
  DigitString as gvcIfDnaHgMHgAddrDataNetworkAddress  

GvcIfDnaDdmRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDnaDdmRowStatus  
  DisplayString as gvcIfDnaDdmComponentName  
  StorageType as gvcIfDnaDdmStorageType  
  NonReplicated as gvcIfDnaDdmIndex  

GvcIfDnaDdmLanAdEntry  
SEQUENCE    
  DashedHexString as gvcIfDnaDdmMac  
  Hex as gvcIfDnaDdmSap  

GvcIfDnaDdmDmoEntry  
SEQUENCE    
  INTEGER as gvcIfDnaDdmDeviceMonitoring  
  INTEGER as gvcIfDnaDdmClearVcsWhenUnreachable  
  Unsigned32 as gvcIfDnaDdmDeviceMonitoringTimer  
  Unsigned32 as gvcIfDnaDdmTestResponseTimer  
  Unsigned32 as gvcIfDnaDdmMaximumTestRetry  

GvcIfDnaDdmDevOpEntry  
SEQUENCE    
  INTEGER as gvcIfDnaDdmDeviceStatus  
  Unsigned32 as gvcIfDnaDdmActiveLinkStations  
  EnterpriseDateAndTime as gvcIfDnaDdmLastTimeUnreachable  
  EnterpriseDateAndTime as gvcIfDnaDdmLastTimeReachable  
  Counter32 as gvcIfDnaDdmDeviceUnreachable  
  INTEGER as gvcIfDnaDdmMonitoringLcn  

GvcIfDnaSdmRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDnaSdmRowStatus  
  DisplayString as gvcIfDnaSdmComponentName  
  StorageType as gvcIfDnaSdmStorageType  
  DigitString as gvcIfDnaSdmIndex  

GvcIfDnaSdmLanAdEntry  
SEQUENCE    
  DashedHexString as gvcIfDnaSdmMac  
  Hex as gvcIfDnaSdmSap  

GvcIfDnaSdmDmoEntry  
SEQUENCE    
  INTEGER as gvcIfDnaSdmDeviceMonitoring  
  INTEGER as gvcIfDnaSdmClearVcsWhenUnreachable  
  Unsigned32 as gvcIfDnaSdmDeviceMonitoringTimer  
  Unsigned32 as gvcIfDnaSdmTestResponseTimer  
  Unsigned32 as gvcIfDnaSdmMaximumTestRetry  

GvcIfDnaSdmDevOpEntry  
SEQUENCE    
  INTEGER as gvcIfDnaSdmDeviceStatus  
  Unsigned32 as gvcIfDnaSdmActiveLinkStations  
  EnterpriseDateAndTime as gvcIfDnaSdmLastTimeUnreachable  
  EnterpriseDateAndTime as gvcIfDnaSdmLastTimeReachable  
  Counter32 as gvcIfDnaSdmDeviceUnreachable  
  INTEGER as gvcIfDnaSdmMonitoringLcn  

GvcIfRgRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfRgRowStatus  
  DisplayString as gvcIfRgComponentName  
  StorageType as gvcIfRgStorageType  
  Integer32 as gvcIfRgIndex  

GvcIfRgIfEntryEntry  
SEQUENCE    
  INTEGER as gvcIfRgIfAdminStatus  
  InterfaceIndex as gvcIfRgIfIndex  

GvcIfRgProvEntry  
SEQUENCE    
  Link as gvcIfRgLinkToProtocolPort  

GvcIfRgOperStatusEntry  
SEQUENCE    
  INTEGER as gvcIfRgSnmpOperStatus  

GvcIfDlciRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDlciRowStatus  
  DisplayString as gvcIfDlciComponentName  
  StorageType as gvcIfDlciStorageType  
  Integer32 as gvcIfDlciIndex  

GvcIfDlciStateEntry  
SEQUENCE    
  INTEGER as gvcIfDlciAdminState  
  INTEGER as gvcIfDlciOperationalState  
  INTEGER as gvcIfDlciUsageState  

GvcIfDlciAbitEntry  
SEQUENCE    
  INTEGER as gvcIfDlciABitStatusFromNetwork  
  INTEGER as gvcIfDlciABitReasonFromNetwork  
  INTEGER as gvcIfDlciABitStatusToNetwork  
  INTEGER as gvcIfDlciABitReasonToNetwork  

GvcIfDlciStatsEntry  
SEQUENCE    
  Counter32 as gvcIfDlciFrmFromNetwork  
  Counter32 as gvcIfDlciFrmToNetwork  
  Counter32 as gvcIfDlciFrmDiscardToNetwork  
  Counter32 as gvcIfDlciFramesWithUnknownSaps  

GvcIfDlciOperEntry  
SEQUENCE    
  INTEGER as gvcIfDlciEncapsulationType  
  DashedHexString as gvcIfDlciLocalDeviceMac  
  DashedHexString as gvcIfDlciRemoteDeviceMac  

GvcIfDlciSpOpEntry  
SEQUENCE    
  INTEGER as gvcIfDlciRateEnforcement  
  Gauge32 as gvcIfDlciCommittedInformationRate  
  Gauge32 as gvcIfDlciCommittedBurstSize  
  Gauge32 as gvcIfDlciExcessInformationRate  
  Gauge32 as gvcIfDlciExcessBurstSize  
  Gauge32 as gvcIfDlciMeasurementInterval  

GvcIfDlciDcRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDlciDcRowStatus  
  DisplayString as gvcIfDlciDcComponentName  
  StorageType as gvcIfDlciDcStorageType  
  NonReplicated as gvcIfDlciDcIndex  

GvcIfDlciDcOptionsEntry  
SEQUENCE    
  INTEGER as gvcIfDlciDcRemoteNpi  
  DigitString as gvcIfDlciDcRemoteDna  
  Unsigned32 as gvcIfDlciDcRemoteDlci  
  INTEGER as gvcIfDlciDcType  
  INTEGER as gvcIfDlciDcTransferPriority  
  INTEGER as gvcIfDlciDcDiscardPriority  

GvcIfDlciDcNfaEntry  
SEQUENCE    
  Integer32 as gvcIfDlciDcNfaIndex  
  HexString as gvcIfDlciDcNfaValue  
  RowStatus as gvcIfDlciDcNfaRowStatus  

GvcIfDlciVcRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDlciVcRowStatus  
  DisplayString as gvcIfDlciVcComponentName  
  StorageType as gvcIfDlciVcStorageType  
  NonReplicated as gvcIfDlciVcIndex  

GvcIfDlciVcCadEntry  
SEQUENCE    
  INTEGER as gvcIfDlciVcType  
  INTEGER as gvcIfDlciVcState  
  INTEGER as gvcIfDlciVcPreviousState  
  Unsigned32 as gvcIfDlciVcDiagnosticCode  
  Unsigned32 as gvcIfDlciVcPreviousDiagnosticCode  
  INTEGER as gvcIfDlciVcCalledNpi  
  DigitString as gvcIfDlciVcCalledDna  
  Unsigned32 as gvcIfDlciVcCalledLcn  
  INTEGER as gvcIfDlciVcCallingNpi  
  DigitString as gvcIfDlciVcCallingDna  
  Unsigned32 as gvcIfDlciVcCallingLcn  
  INTEGER as gvcIfDlciVcAccountingEnabled  
  INTEGER as gvcIfDlciVcFastSelectCall  
  INTEGER as gvcIfDlciVcPathReliability  
  INTEGER as gvcIfDlciVcAccountingEnd  
  INTEGER as gvcIfDlciVcPriority  
  Unsigned32 as gvcIfDlciVcSegmentSize  
  Unsigned32 as gvcIfDlciVcMaxSubnetPktSize  
  INTEGER as gvcIfDlciVcRcosToNetwork  
  INTEGER as gvcIfDlciVcRcosFromNetwork  
  INTEGER as gvcIfDlciVcEmissionPriorityToNetwork  
  INTEGER as gvcIfDlciVcEmissionPriorityFromNetwork  
  AsciiString as gvcIfDlciVcDataPath  

GvcIfDlciVcIntdEntry  
SEQUENCE    
  Hex as gvcIfDlciVcCallReferenceNumber  
  Unsigned32 as gvcIfDlciVcElapsedTimeTillNow  
  Unsigned32 as gvcIfDlciVcSegmentsRx  
  Unsigned32 as gvcIfDlciVcSegmentsSent  
  EnterpriseDateAndTime as gvcIfDlciVcStartTime  

GvcIfDlciVcFrdEntry  
SEQUENCE    
  Unsigned32 as gvcIfDlciVcFrmCongestedToSubnet  
  Unsigned32 as gvcIfDlciVcCannotForwardToSubnet  
  Unsigned32 as gvcIfDlciVcNotDataXferToSubnet  
  Unsigned32 as gvcIfDlciVcOutOfRangeFrmFromSubnet  
  Unsigned32 as gvcIfDlciVcCombErrorsFromSubnet  
  Unsigned32 as gvcIfDlciVcDuplicatesFromSubnet  
  Unsigned32 as gvcIfDlciVcNotDataXferFromSubnet  
  Unsigned32 as gvcIfDlciVcFrmLossTimeouts  
  Unsigned32 as gvcIfDlciVcOoSeqByteCntExceeded  
  Unsigned32 as gvcIfDlciVcPeakOoSeqPktCount  
  Unsigned32 as gvcIfDlciVcPeakOoSeqFrmForwarded  
  Unsigned32 as gvcIfDlciVcSendSequenceNumber  
  Unsigned32 as gvcIfDlciVcPktRetryTimeouts  
  Unsigned32 as gvcIfDlciVcPeakRetryQueueSize  
  Unsigned32 as gvcIfDlciVcSubnetRecoveries  
  Unsigned32 as gvcIfDlciVcOoSeqPktCntExceeded  
  Unsigned32 as gvcIfDlciVcPeakOoSeqByteCount  

GvcIfDlciVcDmepEntry  
SEQUENCE    
  RowPointer as gvcIfDlciVcDmepValue  

GvcIfDlciSpRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDlciSpRowStatus  
  DisplayString as gvcIfDlciSpComponentName  
  StorageType as gvcIfDlciSpStorageType  
  NonReplicated as gvcIfDlciSpIndex  

GvcIfDlciSpParmsEntry  
SEQUENCE    
  INTEGER as gvcIfDlciSpRateEnforcement  
  Unsigned32 as gvcIfDlciSpCommittedInformationRate  
  Unsigned32 as gvcIfDlciSpCommittedBurstSize  
  Unsigned32 as gvcIfDlciSpExcessBurstSize  
  Unsigned32 as gvcIfDlciSpMeasurementInterval  

GvcIfDlciBnnRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDlciBnnRowStatus  
  DisplayString as gvcIfDlciBnnComponentName  
  StorageType as gvcIfDlciBnnStorageType  
  NonReplicated as gvcIfDlciBnnIndex  

GvcIfDlciLdevRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDlciLdevRowStatus  
  DisplayString as gvcIfDlciLdevComponentName  
  StorageType as gvcIfDlciLdevStorageType  
  NonReplicated as gvcIfDlciLdevIndex  

GvcIfDlciLdevAddrEntry  
SEQUENCE    
  DashedHexString as gvcIfDlciLdevMac  

GvcIfDlciLdevDevOpEntry  
SEQUENCE    
  INTEGER as gvcIfDlciLdevDeviceStatus  
  Unsigned32 as gvcIfDlciLdevActiveLinkStations  
  EnterpriseDateAndTime as gvcIfDlciLdevLastTimeUnreachable  
  EnterpriseDateAndTime as gvcIfDlciLdevLastTimeReachable  
  Counter32 as gvcIfDlciLdevDeviceUnreachable  
  INTEGER as gvcIfDlciLdevMonitoringLcn  

GvcIfDlciLdevDmoEntry  
SEQUENCE    
  INTEGER as gvcIfDlciLdevDeviceMonitoring  
  INTEGER as gvcIfDlciLdevClearVcsWhenUnreachable  
  Unsigned32 as gvcIfDlciLdevDeviceMonitoringTimer  
  Unsigned32 as gvcIfDlciLdevTestResponseTimer  
  Unsigned32 as gvcIfDlciLdevMaximumTestRetry  

GvcIfDlciRdevRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDlciRdevRowStatus  
  DisplayString as gvcIfDlciRdevComponentName  
  StorageType as gvcIfDlciRdevStorageType  
  NonReplicated as gvcIfDlciRdevIndex  

GvcIfDlciRdevAddrEntry  
SEQUENCE    
  DashedHexString as gvcIfDlciRdevMac  

GvcIfDlciSapRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDlciSapRowStatus  
  DisplayString as gvcIfDlciSapComponentName  
  StorageType as gvcIfDlciSapStorageType  
  Integer32 as gvcIfDlciSapLocalSapIndex  
  Integer32 as gvcIfDlciSapRemoteSapIndex  

GvcIfDlciSapCircuitRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDlciSapCircuitRowStatus  
  DisplayString as gvcIfDlciSapCircuitComponentName  
  StorageType as gvcIfDlciSapCircuitStorageType  
  DashedHexString as gvcIfDlciSapCircuitS1MacIndex  
  Integer32 as gvcIfDlciSapCircuitS1SapIndex  
  DashedHexString as gvcIfDlciSapCircuitS2MacIndex  
  Integer32 as gvcIfDlciSapCircuitS2SapIndex  

GvcIfFrSvcRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfFrSvcRowStatus  
  DisplayString as gvcIfFrSvcComponentName  
  StorageType as gvcIfFrSvcStorageType  
  NonReplicated as gvcIfFrSvcIndex  

GvcIfFrSvcProvisionedEntry  
SEQUENCE    
  Unsigned32 as gvcIfFrSvcMaximumFrameRelaySvcs  
  INTEGER as gvcIfFrSvcRateEnforcement  
  Unsigned32 as gvcIfFrSvcMaximumCir  

GvcIfFrSvcOperationalEntry  
SEQUENCE    
  Gauge32 as gvcIfFrSvcCurrentNumberOfSvcCalls  

GvcIfSMacFRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfSMacFRowStatus  
  DisplayString as gvcIfSMacFComponentName  
  StorageType as gvcIfSMacFStorageType  
  DashedHexString as gvcIfSMacFIndex  

GvcIfSMacFOperEntry  
SEQUENCE    
  Counter32 as gvcIfSMacFFramesMatchingFilter  

GvcIfDMacFRowStatusEntry  
SEQUENCE    
  RowStatus as gvcIfDMacFRowStatus  
  DisplayString as gvcIfDMacFComponentName  
  StorageType as gvcIfDMacFStorageType  
  DashedHexString as gvcIfDMacFIndex  

GvcIfDMacFOperEntry  
SEQUENCE    
  Counter32 as gvcIfDMacFFramesMatchingFilter