Nortel-MsCarrier-MscPassport-AtmIispMIB

File: Nortel-MsCarrier-MscPassport-AtmIispMIB.mib (176933 bytes)

Imported modules

RFC-1212 Nortel-MsCarrier-MscPassport-UsefulDefinitionsMIB Nortel-MsCarrier-MscPassport-StandardTextualConventionsMIB
Nortel-MsCarrier-MscPassport-TextualConventionsMIB Nortel-MsCarrier-MscPassport-AtmCoreMIB

Imported symbols

OBJECT-TYPE mscPassportMIBs Counter32
DisplayString StorageType RowStatus
Gauge32 Integer32 Unsigned32
Hex NonReplicated HexString
AsciiStringIndex mscAtmIf mscAtmIfVptIndex
mscAtmIfVpt mscAtmIfIndex

Defined Objects

mscAtmIfIisp 1.3.6.1.4.1.562.36.2.1.114.7
OBJECT IDENTIFIER    

mscAtmIfIispRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.7.1
This entry controls the addition and deletion of mscAtmIfIisp components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispRowStatusEntry

mscAtmIfIispRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.7.1.1
A single entry in the table represents a single mscAtmIfIisp component.
OBJECT-TYPE    
  MscAtmIfIispRowStatusEntry  

mscAtmIfIispRowStatus 1.3.6.1.4.1.562.36.2.1.114.7.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfIisp components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfIispComponentName 1.3.6.1.4.1.562.36.2.1.114.7.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfIispStorageType 1.3.6.1.4.1.562.36.2.1.114.7.1.1.4
This variable represents the storage type value for the mscAtmIfIisp tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfIispIndex 1.3.6.1.4.1.562.36.2.1.114.7.1.1.10
This variable represents the index for the mscAtmIfIisp tables.
OBJECT-TYPE    
  NonReplicated  

mscAtmIfIispSig 1.3.6.1.4.1.562.36.2.1.114.7.3
OBJECT IDENTIFIER    

mscAtmIfIispSigRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.7.3.1
This entry controls the addition and deletion of mscAtmIfIispSig components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispSigRowStatusEntry

mscAtmIfIispSigRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.7.3.1.1
A single entry in the table represents a single mscAtmIfIispSig component.
OBJECT-TYPE    
  MscAtmIfIispSigRowStatusEntry  

mscAtmIfIispSigRowStatus 1.3.6.1.4.1.562.36.2.1.114.7.3.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfIispSig components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfIispSigComponentName 1.3.6.1.4.1.562.36.2.1.114.7.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfIispSigStorageType 1.3.6.1.4.1.562.36.2.1.114.7.3.1.1.4
This variable represents the storage type value for the mscAtmIfIispSig tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfIispSigIndex 1.3.6.1.4.1.562.36.2.1.114.7.3.1.1.10
This variable represents the index for the mscAtmIfIispSig tables.
OBJECT-TYPE    
  NonReplicated  

mscAtmIfIispSigVcd 1.3.6.1.4.1.562.36.2.1.114.7.3.2
OBJECT IDENTIFIER    

mscAtmIfIispSigVcdRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.7.3.2.1
This entry controls the addition and deletion of mscAtmIfIispSigVcd components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispSigVcdRowStatusEntry

mscAtmIfIispSigVcdRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.7.3.2.1.1
A single entry in the table represents a single mscAtmIfIispSigVcd component.
OBJECT-TYPE    
  MscAtmIfIispSigVcdRowStatusEntry  

mscAtmIfIispSigVcdRowStatus 1.3.6.1.4.1.562.36.2.1.114.7.3.2.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfIispSigVcd components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfIispSigVcdComponentName 1.3.6.1.4.1.562.36.2.1.114.7.3.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfIispSigVcdStorageType 1.3.6.1.4.1.562.36.2.1.114.7.3.2.1.1.4
This variable represents the storage type value for the mscAtmIfIispSigVcd tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfIispSigVcdIndex 1.3.6.1.4.1.562.36.2.1.114.7.3.2.1.1.10
This variable represents the index for the mscAtmIfIispSigVcd tables.
OBJECT-TYPE    
  NonReplicated  

mscAtmIfIispSigVcdProvTable 1.3.6.1.4.1.562.36.2.1.114.7.3.2.10
This group contains the provisionable traffic attributes for a control channel.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispSigVcdProvEntry

mscAtmIfIispSigVcdProvEntry 1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1
An entry in the mscAtmIfIispSigVcdProvTable.
OBJECT-TYPE    
  MscAtmIfIispSigVcdProvEntry  

mscAtmIfIispSigVcdTrafficDescType 1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1.1
This attribute specifies the type of traffic management which is applied to both the transmit and receive direction of this connection as defined in the ATM Forum. The trafficDescType determines the number and meaning of the parameters in the trafficDescParm attribute.
OBJECT-TYPE    
  INTEGER n3(3), n6(6), n7(7), n8(8)  

mscAtmIfIispSigVcdAtmServiceCategory 1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1.3
This attribute specifies the ATM service category for both directions of the connection. The constantBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by CellTransfer Delay are assumed to be of significantly reduce value to the application. The rtVariableBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by CTD are assumed to be of significantly reduced value to the application. Real time VBR service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. Non-real time VBR service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications; that is, those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection.
OBJECT-TYPE    
  INTEGER unspecifiedBitRate(0), constantBitRate(1), rtVariableBitRate(2), nrtVariableBitRate(3)  

mscAtmIfIispSigVcdWeight 1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1.4
This attribute specifies an override for the weight of this unshaped connection. This attribute is ignored for shaped connections, for ABR connections, for connections on a CQC-based ATM FP and basic VPTs. When the value is set to sameAsCa, the weight is determined by the weight policy attribute under the CA service category component for all but standard VPT VCCs. For standard VPT VCCs, the weight is determined by the VCC's service category, when the value is set to sameAsCa. When this attribute is set to a value from 1 to 4095, that value is used for the weight policy of this connection relative to other connections. For all but standard VPT VCCs, weight policy determines the proportion of transit cell opportunities which are allocated to this connection, compared to other connections in the same service category. For standard VPT VCCs, weight policy determines the proportion of transmit cell opportunities which are allocated to this connection, compared to other connections associated with the VPT. When the value is set to upToQueueLimit, the weight policy is limited only by the txQueueLimit. VALUES ( 0 = upToQueueLimit 65535 = sameAsCa )
OBJECT-TYPE    
  Unsigned32 0 | 1..4095 | 65535  

mscAtmIfIispSigVcdQosClass 1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1.21
This attribute specifies the quality of service for both the forward and backward direction for this connection. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters.
OBJECT-TYPE    
  INTEGER n0(0), n1(1), n2(2), n3(3), n4(4)  

mscAtmIfIispSigVcdTrafficShaping 1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1.50
This attribute specifies whether this connection uses traffic shaping when transmitting traffic to the ATM interface. When sameAsCa is selected, traffic shaping for this connection is based on the trafficShaping attribute of the connection's service category component under the AtmIf CA. If the service category has traffic shaping enabled, then traffic shaping is enabled for the connection. Note that enabling traffic shaping may have no effect under certain cases. These cases are listed in the description of the trafficShaping operational attribute, which is under the Vcc Tm and Vpc Tm components. When disabled is selected, traffic shaping for this connection is disabled.
OBJECT-TYPE    
  INTEGER disabled(1), sameAsCa(2)  

mscAtmIfIispSigVcdUnshapedTransmitQueueing 1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1.60
This attribute only applies when this connection is unshaped. This attribute specifies the transmit queueing method for this connection if it is unshaped. Refer to the unshapedTransmitQueueing attribute under the AtmIf CA service category subcomponent for more details on the meaning of this attribute. When this attribute is set to sameAsCa, the transmit queueing method for the connection is based on the unshapedTransmitQueueing attribute of the connection's service category component under the ConnectionAdministrator. When this attribute is set to common, transmit traffic on this unshaped connection is destined for the common queue. The value sameAsInterface is for migration from previous software releases, but should no longer be used
OBJECT-TYPE    
  INTEGER common(1), sameAsCa(3)  

mscAtmIfIispSigVcdUsageParameterControl 1.3.6.1.4.1.562.36.2.1.114.7.3.2.10.1.70
This attribute specifies whether this connection enforces usage parameter control when receiving traffic from the ATM interface. When sameAsCa is selected, UPC for the connection is based on the usageParameterControl attribute of the connection's service category component under the ConnectionAdministrator. If the service category has UPC enabled, then UPC is enabled for the connection. Note that enabling UPC may have no effect under certain cases. These cases are listed in the description of the usageParameterControl operational attribute, which is under the Vcc Tm or Vpc Tm component. When disabled is selected, UPC for this connection is disabled. The value sameAsInterface is for migration from previous software releases, but should no longer be used
OBJECT-TYPE    
  INTEGER disabled(1), sameAsCa(2)  

mscAtmIfIispSigVcdTdpTable 1.3.6.1.4.1.562.36.2.1.114.7.3.2.387
This attribute is a vector of five traffic parameters whose meanings are defined by the trafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When trafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When trafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For trafficDescType 3 the traffic is shaped at the next rate less than the PCR. For trafficDescType 6, 7, and 8, the traffic is shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic is shaped at the next rate above the PCR.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispSigVcdTdpEntry

mscAtmIfIispSigVcdTdpEntry 1.3.6.1.4.1.562.36.2.1.114.7.3.2.387.1
An entry in the mscAtmIfIispSigVcdTdpTable.
OBJECT-TYPE    
  MscAtmIfIispSigVcdTdpEntry  

mscAtmIfIispSigVcdTdpIndex 1.3.6.1.4.1.562.36.2.1.114.7.3.2.387.1.1
This variable represents the mscAtmIfIispSigVcdTdpTable specific index for the mscAtmIfIispSigVcdTdpTable.
OBJECT-TYPE    
  Integer32 1..5  

mscAtmIfIispSigVcdTdpValue 1.3.6.1.4.1.562.36.2.1.114.7.3.2.387.1.2
This variable represents an individual value for the mscAtmIfIispSigVcdTdpTable.
OBJECT-TYPE    
  Unsigned32 0..2147483647  

mscAtmIfIispSigProvTable 1.3.6.1.4.1.562.36.2.1.114.7.3.10
This attribute group contains the provisionable attributes for the Signalling component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispSigProvEntry

mscAtmIfIispSigProvEntry 1.3.6.1.4.1.562.36.2.1.114.7.3.10.1
An entry in the mscAtmIfIispSigProvTable.
OBJECT-TYPE    
  MscAtmIfIispSigProvEntry  

mscAtmIfIispSigVci 1.3.6.1.4.1.562.36.2.1.114.7.3.10.1.1
This attribute specifies the signalling channel number.
OBJECT-TYPE    
  Unsigned32 0..65535  

mscAtmIfIispSigAddressConversion 1.3.6.1.4.1.562.36.2.1.114.7.3.10.1.2
This attribute specifies the address conversion on the outgoing signalling PDUs. The options are none, nativeE164, or nsap. The none option is the default and if this option is chosen then nothing is done to the address information element (IE) in the outgoing signalling message. If nativeE164 option is chosen, then only NSAP encapsulated E.164 addresses with zeros in the ESI are converted to native E.164 format in the outgoing signalling message. If the NSAP address is not encapsulated E.164 or the ESI field is not zeros and the nativeE164 option is chosen, then the call is cleared. If the nsap option is chosen, then native E.164 addresses are converted to NSAP E.164 with zeros in the ESI field; otherwise the address is in NSAP format and is not changed.
OBJECT-TYPE    
  INTEGER none(0), nativeE164(1), nsap(2)  

mscAtmIfIispSigOperatingMode 1.3.6.1.4.1.562.36.2.1.114.7.3.10.1.3
This attribute specifies the operating mode of the signaling channel. provisionedOnly indicates that only SPVCs and SPVPs are supported on the interface and SVCs are not supported. This value is permitted only on UNI interfaces. normal indicates that SVCs, SPVCs, and SPVPs are supported on the interface.
OBJECT-TYPE    
  INTEGER normal(0), provisionedOnly(1)  

mscAtmIfIispSigStateTable 1.3.6.1.4.1.562.36.2.1.114.7.3.11
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispSigStateEntry

mscAtmIfIispSigStateEntry 1.3.6.1.4.1.562.36.2.1.114.7.3.11.1
An entry in the mscAtmIfIispSigStateTable.
OBJECT-TYPE    
  MscAtmIfIispSigStateEntry  

mscAtmIfIispSigAdminState 1.3.6.1.4.1.562.36.2.1.114.7.3.11.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscAtmIfIispSigOperationalState 1.3.6.1.4.1.562.36.2.1.114.7.3.11.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscAtmIfIispSigUsageState 1.3.6.1.4.1.562.36.2.1.114.7.3.11.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscAtmIfIispSigOperTable 1.3.6.1.4.1.562.36.2.1.114.7.3.12
This attribute contains the operational attributes for the AtmSignalling component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispSigOperEntry

mscAtmIfIispSigOperEntry 1.3.6.1.4.1.562.36.2.1.114.7.3.12.1
An entry in the mscAtmIfIispSigOperTable.
OBJECT-TYPE    
  MscAtmIfIispSigOperEntry  

mscAtmIfIispSigLastTxCauseCode 1.3.6.1.4.1.562.36.2.1.114.7.3.12.1.1
This attribute indicates the cause code in the last transmitted signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
OBJECT-TYPE    
  Unsigned32 0..255  

mscAtmIfIispSigLastTxDiagCode 1.3.6.1.4.1.562.36.2.1.114.7.3.12.1.2
This attribute contains the diagnostic code in the last transmitted signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
OBJECT-TYPE    
  Hex 0..255  

mscAtmIfIispSigLastRxCauseCode 1.3.6.1.4.1.562.36.2.1.114.7.3.12.1.3
This attribute contains the cause code in the last received signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
OBJECT-TYPE    
  Unsigned32 0..255  

mscAtmIfIispSigLastRxDiagCode 1.3.6.1.4.1.562.36.2.1.114.7.3.12.1.4
This attribute contains the diagnostic code in the last received signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
OBJECT-TYPE    
  Hex 0..255  

mscAtmIfIispSigStatsTable 1.3.6.1.4.1.562.36.2.1.114.7.3.13
This attribute group contains the statistics associated with the AtmSignalling component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispSigStatsEntry

mscAtmIfIispSigStatsEntry 1.3.6.1.4.1.562.36.2.1.114.7.3.13.1
An entry in the mscAtmIfIispSigStatsTable.
OBJECT-TYPE    
  MscAtmIfIispSigStatsEntry  

mscAtmIfIispSigCurrentConnections 1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.1
This attribute indicates the total number of currently active connections.
OBJECT-TYPE    
  Counter32  

mscAtmIfIispSigPeakConnections 1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.2
This attribute indicates the high water mark of active point-to- point and point-to-multipoint connections.
OBJECT-TYPE    
  Gauge32 0..4294967295  

mscAtmIfIispSigSuccessfulConnections 1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.3
This attribute counts the total number of switched point-to- point and point-to-multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
OBJECT-TYPE    
  Counter32  

mscAtmIfIispSigFailedConnections 1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.4
This attribute counts the total number of switched connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
OBJECT-TYPE    
  Counter32  

mscAtmIfIispSigTxPdus 1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.5
This attribute counts the number of transmitted signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
OBJECT-TYPE    
  Counter32  

mscAtmIfIispSigRxPdus 1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.6
This attribute counts the number of received signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
OBJECT-TYPE    
  Counter32  

mscAtmIfIispSigCurrentPmpConnections 1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.7
This attribute indicates the number of currently active point-to- multipoint connections.
OBJECT-TYPE    
  Gauge32 0..4294967295  

mscAtmIfIispSigPeakPmpConnections 1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.8
This attribute indicates the high water mark of active point-to- multipoint connections.
OBJECT-TYPE    
  Gauge32 0..4294967295  

mscAtmIfIispSigSuccessfulPmpConnections 1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.9
This attribute counts the total number of switched point-to- multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
OBJECT-TYPE    
  Counter32  

mscAtmIfIispSigFailedPmpConnections 1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.10
This attribute counts the number of switched point-to- multipoint connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
OBJECT-TYPE    
  Counter32  

mscAtmIfIispSigNewCurrentConnections 1.3.6.1.4.1.562.36.2.1.114.7.3.13.1.11
This attribute indicates the total number of currently active point-to- point and point-to-multipoint connections.
OBJECT-TYPE    
  Gauge32 0..4294967295  

mscAtmIfIispAddr 1.3.6.1.4.1.562.36.2.1.114.7.4
OBJECT IDENTIFIER    

mscAtmIfIispAddrRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.7.4.1
This entry controls the addition and deletion of mscAtmIfIispAddr components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispAddrRowStatusEntry

mscAtmIfIispAddrRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.7.4.1.1
A single entry in the table represents a single mscAtmIfIispAddr component.
OBJECT-TYPE    
  MscAtmIfIispAddrRowStatusEntry  

mscAtmIfIispAddrRowStatus 1.3.6.1.4.1.562.36.2.1.114.7.4.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfIispAddr components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfIispAddrComponentName 1.3.6.1.4.1.562.36.2.1.114.7.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfIispAddrStorageType 1.3.6.1.4.1.562.36.2.1.114.7.4.1.1.4
This variable represents the storage type value for the mscAtmIfIispAddr tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfIispAddrAddressIndex 1.3.6.1.4.1.562.36.2.1.114.7.4.1.1.10
This variable represents an index for the mscAtmIfIispAddr tables.
OBJECT-TYPE    
  AsciiStringIndex SIZE(1..40)  

mscAtmIfIispAddrAddressTypeIndex 1.3.6.1.4.1.562.36.2.1.114.7.4.1.1.11
This variable represents an index for the mscAtmIfIispAddr tables.
OBJECT-TYPE    
  INTEGER primary(0), alternate(1), default(3)  

mscAtmIfIispAddrTermSP 1.3.6.1.4.1.562.36.2.1.114.7.4.2
OBJECT IDENTIFIER    

mscAtmIfIispAddrTermSPRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.7.4.2.1
This entry controls the addition and deletion of mscAtmIfIispAddrTermSP components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispAddrTermSPRowStatusEntry

mscAtmIfIispAddrTermSPRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.7.4.2.1.1
A single entry in the table represents a single mscAtmIfIispAddrTermSP component.
OBJECT-TYPE    
  MscAtmIfIispAddrTermSPRowStatusEntry  

mscAtmIfIispAddrTermSPRowStatus 1.3.6.1.4.1.562.36.2.1.114.7.4.2.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfIispAddrTermSP components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfIispAddrTermSPComponentName 1.3.6.1.4.1.562.36.2.1.114.7.4.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfIispAddrTermSPStorageType 1.3.6.1.4.1.562.36.2.1.114.7.4.2.1.1.4
This variable represents the storage type value for the mscAtmIfIispAddrTermSP tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfIispAddrTermSPIndex 1.3.6.1.4.1.562.36.2.1.114.7.4.2.1.1.10
This variable represents the index for the mscAtmIfIispAddrTermSP tables.
OBJECT-TYPE    
  NonReplicated  

mscAtmIfIispAddrPnniInfo 1.3.6.1.4.1.562.36.2.1.114.7.4.3
OBJECT IDENTIFIER    

mscAtmIfIispAddrPnniInfoRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.7.4.3.1
This entry controls the addition and deletion of mscAtmIfIispAddrPnniInfo components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispAddrPnniInfoRowStatusEntry

mscAtmIfIispAddrPnniInfoRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.7.4.3.1.1
A single entry in the table represents a single mscAtmIfIispAddrPnniInfo component.
OBJECT-TYPE    
  MscAtmIfIispAddrPnniInfoRowStatusEntry  

mscAtmIfIispAddrPnniInfoRowStatus 1.3.6.1.4.1.562.36.2.1.114.7.4.3.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfIispAddrPnniInfo components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfIispAddrPnniInfoComponentName 1.3.6.1.4.1.562.36.2.1.114.7.4.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfIispAddrPnniInfoStorageType 1.3.6.1.4.1.562.36.2.1.114.7.4.3.1.1.4
This variable represents the storage type value for the mscAtmIfIispAddrPnniInfo tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfIispAddrPnniInfoIndex 1.3.6.1.4.1.562.36.2.1.114.7.4.3.1.1.10
This variable represents the index for the mscAtmIfIispAddrPnniInfo tables.
OBJECT-TYPE    
  NonReplicated  

mscAtmIfIispAddrPnniInfoProvTable 1.3.6.1.4.1.562.36.2.1.114.7.4.3.10
This attribute group contains the provisioned attributes relating to PNNI for a PnniInfo component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispAddrPnniInfoProvEntry

mscAtmIfIispAddrPnniInfoProvEntry 1.3.6.1.4.1.562.36.2.1.114.7.4.3.10.1
An entry in the mscAtmIfIispAddrPnniInfoProvTable.
OBJECT-TYPE    
  MscAtmIfIispAddrPnniInfoProvEntry  

mscAtmIfIispAddrPnniInfoScope 1.3.6.1.4.1.562.36.2.1.114.7.4.3.10.1.1
This attribute specifies the scope of the ATM address, which is the highest level up to which this address will be advertised in the PNNI hierarchy. The scope must be set to a value numerically less than or equal to the level of the lowest level peer group containing this node. Setting the scope to 0 will cause the address to be advertised globally within this PNNI routing domain.
OBJECT-TYPE    
  INTEGER -1..104  

mscAtmIfIispAddrPnniInfoReachability 1.3.6.1.4.1.562.36.2.1.114.7.4.3.10.1.2
This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
OBJECT-TYPE    
  INTEGER internal(0), exterior(1)  

mscAtmIfIispAddrOperTable 1.3.6.1.4.1.562.36.2.1.114.7.4.10
This attribute group contains the operational attributes for the Address component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispAddrOperEntry

mscAtmIfIispAddrOperEntry 1.3.6.1.4.1.562.36.2.1.114.7.4.10.1
An entry in the mscAtmIfIispAddrOperTable.
OBJECT-TYPE    
  MscAtmIfIispAddrOperEntry  

mscAtmIfIispAddrScope 1.3.6.1.4.1.562.36.2.1.114.7.4.10.1.1
This attribute indicates the scope of the ATM address, which is the highest level to which this address will be advertised in the PNNI hierarchy. If no PnniInfo subcomponent has been provisioned, then the scope will default to the level of this node in the PNNI hierarchy. If this node does not participate in a PNNI hierarchy, then this attribute will have the value of -1.
OBJECT-TYPE    
  INTEGER -1..104  

mscAtmIfIispAddrReachability 1.3.6.1.4.1.562.36.2.1.114.7.4.10.1.2
This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
OBJECT-TYPE    
  INTEGER internal(0), exterior(1)  

mscAtmIfIispCallingAScr 1.3.6.1.4.1.562.36.2.1.114.7.5
OBJECT IDENTIFIER    

mscAtmIfIispCallingAScrRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.7.5.1
This entry controls the addition and deletion of mscAtmIfIispCallingAScr components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispCallingAScrRowStatusEntry

mscAtmIfIispCallingAScrRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.7.5.1.1
A single entry in the table represents a single mscAtmIfIispCallingAScr component.
OBJECT-TYPE    
  MscAtmIfIispCallingAScrRowStatusEntry  

mscAtmIfIispCallingAScrRowStatus 1.3.6.1.4.1.562.36.2.1.114.7.5.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfIispCallingAScr components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfIispCallingAScrComponentName 1.3.6.1.4.1.562.36.2.1.114.7.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfIispCallingAScrStorageType 1.3.6.1.4.1.562.36.2.1.114.7.5.1.1.4
This variable represents the storage type value for the mscAtmIfIispCallingAScr tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfIispCallingAScrIndex 1.3.6.1.4.1.562.36.2.1.114.7.5.1.1.10
This variable represents the index for the mscAtmIfIispCallingAScr tables.
OBJECT-TYPE    
  NonReplicated  

mscAtmIfIispCallingAScrAddr 1.3.6.1.4.1.562.36.2.1.114.7.5.2
OBJECT IDENTIFIER    

mscAtmIfIispCallingAScrAddrRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.7.5.2.1
This entry controls the addition and deletion of mscAtmIfIispCallingAScrAddr components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispCallingAScrAddrRowStatusEntry

mscAtmIfIispCallingAScrAddrRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.7.5.2.1.1
A single entry in the table represents a single mscAtmIfIispCallingAScrAddr component.
OBJECT-TYPE    
  MscAtmIfIispCallingAScrAddrRowStatusEntry  

mscAtmIfIispCallingAScrAddrRowStatus 1.3.6.1.4.1.562.36.2.1.114.7.5.2.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfIispCallingAScrAddr components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfIispCallingAScrAddrComponentName 1.3.6.1.4.1.562.36.2.1.114.7.5.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfIispCallingAScrAddrStorageType 1.3.6.1.4.1.562.36.2.1.114.7.5.2.1.1.4
This variable represents the storage type value for the mscAtmIfIispCallingAScrAddr tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfIispCallingAScrAddrAddressIndex 1.3.6.1.4.1.562.36.2.1.114.7.5.2.1.1.10
This variable represents an index for the mscAtmIfIispCallingAScrAddr tables.
OBJECT-TYPE    
  AsciiStringIndex SIZE(1..40)  

mscAtmIfIispCallingAScrAddrAddressActionIndex 1.3.6.1.4.1.562.36.2.1.114.7.5.2.1.1.11
This variable represents an index for the mscAtmIfIispCallingAScrAddr tables.
OBJECT-TYPE    
  INTEGER accept(0), reject(1)  

mscAtmIfIispCallingAScrProvTable 1.3.6.1.4.1.562.36.2.1.114.7.5.10
This attribute group contains the provisionable attributes for the CallingAScr component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispCallingAScrProvEntry

mscAtmIfIispCallingAScrProvEntry 1.3.6.1.4.1.562.36.2.1.114.7.5.10.1
An entry in the mscAtmIfIispCallingAScrProvTable.
OBJECT-TYPE    
  MscAtmIfIispCallingAScrProvEntry  

mscAtmIfIispCallingAScrAdminStatus 1.3.6.1.4.1.562.36.2.1.114.7.5.10.1.1
This attribute specifies whether the calling address screening feature is enabled or disabled. If enabled, incoming SVC calls are screened against provisioned addresses. If enabled and the calling address in the ATM SVC call request is provisioned to be accepted, the call is accepted or rejected according to the action specified for that address. If the value is enabled, and the calling address in the address request is not provisioned, the call is rejected If the value is disabled, no calling address screening is performed.
OBJECT-TYPE    
  INTEGER enabled(0), disabled(1)  

mscAtmIfIispCallingAScrDefaultInsertionAddress 1.3.6.1.4.1.562.36.2.1.114.7.5.10.1.2
This attribute specifies the address to be inserted into the SVC connection request if adminStatus is enabled and the connection request does not contain a calling address. If the adminStatus attribute is enabled and this attribute is empty, all incoming SVC calls which do not contain a calling address are rejected.
OBJECT-TYPE    
  HexString SIZE(0..20)  

mscAtmIfIispCallingAScrStatTable 1.3.6.1.4.1.562.36.2.1.114.7.5.11
This attribute group contains statistics related to the incoming SVC call requests received while the adminStatus attribute is set to enabled.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispCallingAScrStatEntry

mscAtmIfIispCallingAScrStatEntry 1.3.6.1.4.1.562.36.2.1.114.7.5.11.1
An entry in the mscAtmIfIispCallingAScrStatTable.
OBJECT-TYPE    
  MscAtmIfIispCallingAScrStatEntry  

mscAtmIfIispCallingAScrAcceptedCalls 1.3.6.1.4.1.562.36.2.1.114.7.5.11.1.1
This attribute counts the incoming SVC calls which were accepted because the address specified in the call request matched a provisioned ATM address and the associated action was accept. When the counter exceeds the maximum, it wraps to 0.
OBJECT-TYPE    
  Counter32  

mscAtmIfIispCallingAScrRejectedCalls 1.3.6.1.4.1.562.36.2.1.114.7.5.11.1.2
This attribute counts the incoming SVC calls which were rejected because the address specified in the call request matched a provisioned ATM address, but the associated action was reject. When the counter exceeds the maximum, it wraps to 0.
OBJECT-TYPE    
  Counter32  

mscAtmIfIispCallingAScrUnmatchedCalls 1.3.6.1.4.1.562.36.2.1.114.7.5.11.1.3
This attribute counts the incoming SVC calls which were rejected because none of the provisioned ATM addresses matched the applicable address in the incoming SVC call request. When the counter exceeds the maximum, it wraps to 0.
OBJECT-TYPE    
  Counter32  

mscAtmIfIispCalledAScr 1.3.6.1.4.1.562.36.2.1.114.7.6
OBJECT IDENTIFIER    

mscAtmIfIispCalledAScrRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.7.6.1
This entry controls the addition and deletion of mscAtmIfIispCalledAScr components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispCalledAScrRowStatusEntry

mscAtmIfIispCalledAScrRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.7.6.1.1
A single entry in the table represents a single mscAtmIfIispCalledAScr component.
OBJECT-TYPE    
  MscAtmIfIispCalledAScrRowStatusEntry  

mscAtmIfIispCalledAScrRowStatus 1.3.6.1.4.1.562.36.2.1.114.7.6.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfIispCalledAScr components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfIispCalledAScrComponentName 1.3.6.1.4.1.562.36.2.1.114.7.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfIispCalledAScrStorageType 1.3.6.1.4.1.562.36.2.1.114.7.6.1.1.4
This variable represents the storage type value for the mscAtmIfIispCalledAScr tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfIispCalledAScrIndex 1.3.6.1.4.1.562.36.2.1.114.7.6.1.1.10
This variable represents the index for the mscAtmIfIispCalledAScr tables.
OBJECT-TYPE    
  NonReplicated  

mscAtmIfIispCalledAScrAddr 1.3.6.1.4.1.562.36.2.1.114.7.6.2
OBJECT IDENTIFIER    

mscAtmIfIispCalledAScrAddrRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.7.6.2.1
This entry controls the addition and deletion of mscAtmIfIispCalledAScrAddr components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispCalledAScrAddrRowStatusEntry

mscAtmIfIispCalledAScrAddrRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.7.6.2.1.1
A single entry in the table represents a single mscAtmIfIispCalledAScrAddr component.
OBJECT-TYPE    
  MscAtmIfIispCalledAScrAddrRowStatusEntry  

mscAtmIfIispCalledAScrAddrRowStatus 1.3.6.1.4.1.562.36.2.1.114.7.6.2.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfIispCalledAScrAddr components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfIispCalledAScrAddrComponentName 1.3.6.1.4.1.562.36.2.1.114.7.6.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfIispCalledAScrAddrStorageType 1.3.6.1.4.1.562.36.2.1.114.7.6.2.1.1.4
This variable represents the storage type value for the mscAtmIfIispCalledAScrAddr tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfIispCalledAScrAddrAddressIndex 1.3.6.1.4.1.562.36.2.1.114.7.6.2.1.1.10
This variable represents an index for the mscAtmIfIispCalledAScrAddr tables.
OBJECT-TYPE    
  AsciiStringIndex SIZE(1..40)  

mscAtmIfIispCalledAScrAddrAddressActionIndex 1.3.6.1.4.1.562.36.2.1.114.7.6.2.1.1.11
This variable represents an index for the mscAtmIfIispCalledAScrAddr tables.
OBJECT-TYPE    
  INTEGER accept(0), reject(1)  

mscAtmIfIispCalledAScrProvTable 1.3.6.1.4.1.562.36.2.1.114.7.6.10
This attribute group contains the provisionable attributes for the CalledAScr component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispCalledAScrProvEntry

mscAtmIfIispCalledAScrProvEntry 1.3.6.1.4.1.562.36.2.1.114.7.6.10.1
An entry in the mscAtmIfIispCalledAScrProvTable.
OBJECT-TYPE    
  MscAtmIfIispCalledAScrProvEntry  

mscAtmIfIispCalledAScrAdminStatus 1.3.6.1.4.1.562.36.2.1.114.7.6.10.1.1
This attribute specifies whether the called address screening feature is enabled or disabled. If the value is enabled, incoming SVC calls will be screened against provisioned called addresses. If the value is enabled and the called address in the ATM SVC call request has been provisioned, the call is accepted or rejected according to the action specified for that address. If the value is enabled and the called address in the call request is not provisioned, the call is rejected. If the value is disabled, no called address screening is performed.
OBJECT-TYPE    
  INTEGER enabled(0), disabled(1)  

mscAtmIfIispCalledAScrStatTable 1.3.6.1.4.1.562.36.2.1.114.7.6.11
This attribute group contains statistics related to the incoming SVC call requests received while the adminStatus attribute is set to enabled.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispCalledAScrStatEntry

mscAtmIfIispCalledAScrStatEntry 1.3.6.1.4.1.562.36.2.1.114.7.6.11.1
An entry in the mscAtmIfIispCalledAScrStatTable.
OBJECT-TYPE    
  MscAtmIfIispCalledAScrStatEntry  

mscAtmIfIispCalledAScrAcceptedCalls 1.3.6.1.4.1.562.36.2.1.114.7.6.11.1.1
This attribute counts the incoming SVC calls which were accepted because the address specified in the call request matched a provisioned ATM address and the associated action was accept. When the counter exceeds the maximum, it wraps to 0.
OBJECT-TYPE    
  Counter32  

mscAtmIfIispCalledAScrRejectedCalls 1.3.6.1.4.1.562.36.2.1.114.7.6.11.1.2
This attribute counts the incoming SVC calls which were rejected because the address specified in the call request matched a provisioned ATM address, but the associated action was reject. When the counter exceeds the maximum, it wraps to 0.
OBJECT-TYPE    
  Counter32  

mscAtmIfIispCalledAScrUnmatchedCalls 1.3.6.1.4.1.562.36.2.1.114.7.6.11.1.3
This attribute counts the incoming SVC calls which were rejected because none of the provisioned ATM addresses matched the applicable address in the incoming SVC call request. When the counter exceeds the maximum, it wraps to 0.
OBJECT-TYPE    
  Counter32  

mscAtmIfIispProvTable 1.3.6.1.4.1.562.36.2.1.114.7.10
This group contains the provisionable attributes for the Iisp component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispProvEntry

mscAtmIfIispProvEntry 1.3.6.1.4.1.562.36.2.1.114.7.10.1
An entry in the mscAtmIfIispProvTable.
OBJECT-TYPE    
  MscAtmIfIispProvEntry  

mscAtmIfIispVersion 1.3.6.1.4.1.562.36.2.1.114.7.10.1.1
This attribute indicates which specification the IISP interface complies with. The options are iisp10Sig30 which refers to IISP version 1.0 with 3.0 signalling and iisp10Sig31 which refers to IISP version 1.0 with 3.1 signalling. If this attribute is changed, all switched Vcc components in this interface are cleared due to the fact that the two versions are incompatible.
OBJECT-TYPE    
  INTEGER iisp10Sig30(2), iisp10Sig31(3)  

mscAtmIfIispSide 1.3.6.1.4.1.562.36.2.1.114.7.10.1.2
This attribute indicates which side the interface is, user or network.
OBJECT-TYPE    
  INTEGER networkSide(0), userSide(1)  

mscAtmIfIispSoftPvcRetryPeriod 1.3.6.1.4.1.562.36.2.1.114.7.10.1.3
This attribute specifies the time to wait between call set up retries. The resolution is to the nearest 10 seconds. This attribute has been obsoleted and is replaced by the softPvpAndPvcRetryPeriod attribute.
OBJECT-TYPE    
  Unsigned32 20..999999  

mscAtmIfIispSoftPvpAndPvcRetryPeriod 1.3.6.1.4.1.562.36.2.1.114.7.10.1.4
This attribute specifies the time to wait between soft PVP or soft PVC call setup retries. The resolution is to the nearest 10 seconds.
OBJECT-TYPE    
  Unsigned32 20..999999  

mscAtmIfIispSoftPvpAndPvcHoldOffTime 1.3.6.1.4.1.562.36.2.1.114.7.10.1.5
This attribute specifies how long to hold off retries following a release or the connection. The resolution is to the nearest 50 ms.
OBJECT-TYPE    
  Unsigned32 0 | 50..20000  

mscAtmIfIispAcctOptTable 1.3.6.1.4.1.562.36.2.1.114.7.11
This group contains the provisionable attributes for accounting.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfIispAcctOptEntry

mscAtmIfIispAcctOptEntry 1.3.6.1.4.1.562.36.2.1.114.7.11.1
An entry in the mscAtmIfIispAcctOptTable.
OBJECT-TYPE    
  MscAtmIfIispAcctOptEntry  

mscAtmIfIispAccountCollection 1.3.6.1.4.1.562.36.2.1.114.7.11.1.1
This attribute is used to turn accounting on or off for SVC and SPVC connections. It also specifies the reason(s) for which accounting data is collected: billing, test, study, audit, or force. If the set of reasons is not empty then accounting records will be generated by this interface in the following situations: - on a TODA changeover if TODA is enabled; - every 12 hours (per connection) if TODA is disabled; - on every call clear (a call record with final cell counts). If none of the reasons is present, then accounting will be suppressed. The reason for collection is recorded in the accounting record, in the attribute callingCollectReason or calledCollectReason as appropriate. Description of bits: bill(0) test(1) study(2) audit(3) force(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscAtmIfIispAccountConnectionType 1.3.6.1.4.1.562.36.2.1.114.7.11.1.2
This attribute specifies whether accounting records generated by this interface should be marked as originating, terminating or intermediate. This attribute, in combination with the direction of the call, determines the value of attribute connPointType of the accounting record and may be used by downstream accounting processes to correlate the records. If the value is origTerm then records generated for incoming calls will be marked as originating and records generated for outgoing calls will be marked as terminating. If the value is intermediate then records generated for all calls will be marked as intermediate.
OBJECT-TYPE    
  INTEGER origTerm(0), intermediate(1)  

mscAtmIfIispAccountClass 1.3.6.1.4.1.562.36.2.1.114.7.11.1.3
This attribute specifies the accounting class associated with the interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingServiceType or calledServiceType as appropriate.
OBJECT-TYPE    
  Unsigned32 0..255  

mscAtmIfIispServiceExchange 1.3.6.1.4.1.562.36.2.1.114.7.11.1.4
This attribute specifies the data service exchange associated with this interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingDse or calledDse as appropriate.
OBJECT-TYPE    
  Unsigned32 0..255  

mscAtmIfVptIisp 1.3.6.1.4.1.562.36.2.1.114.9.6
OBJECT IDENTIFIER    

mscAtmIfVptIispRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.9.6.1
This entry controls the addition and deletion of mscAtmIfVptIisp components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispRowStatusEntry

mscAtmIfVptIispRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.1.1
A single entry in the table represents a single mscAtmIfVptIisp component.
OBJECT-TYPE    
  MscAtmIfVptIispRowStatusEntry  

mscAtmIfVptIispRowStatus 1.3.6.1.4.1.562.36.2.1.114.9.6.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfVptIisp components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfVptIispComponentName 1.3.6.1.4.1.562.36.2.1.114.9.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfVptIispStorageType 1.3.6.1.4.1.562.36.2.1.114.9.6.1.1.4
This variable represents the storage type value for the mscAtmIfVptIisp tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfVptIispIndex 1.3.6.1.4.1.562.36.2.1.114.9.6.1.1.10
This variable represents the index for the mscAtmIfVptIisp tables.
OBJECT-TYPE    
  NonReplicated  

mscAtmIfVptIispSig 1.3.6.1.4.1.562.36.2.1.114.9.6.3
OBJECT IDENTIFIER    

mscAtmIfVptIispSigRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.9.6.3.1
This entry controls the addition and deletion of mscAtmIfVptIispSig components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispSigRowStatusEntry

mscAtmIfVptIispSigRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.3.1.1
A single entry in the table represents a single mscAtmIfVptIispSig component.
OBJECT-TYPE    
  MscAtmIfVptIispSigRowStatusEntry  

mscAtmIfVptIispSigRowStatus 1.3.6.1.4.1.562.36.2.1.114.9.6.3.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfVptIispSig components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfVptIispSigComponentName 1.3.6.1.4.1.562.36.2.1.114.9.6.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfVptIispSigStorageType 1.3.6.1.4.1.562.36.2.1.114.9.6.3.1.1.4
This variable represents the storage type value for the mscAtmIfVptIispSig tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfVptIispSigIndex 1.3.6.1.4.1.562.36.2.1.114.9.6.3.1.1.10
This variable represents the index for the mscAtmIfVptIispSig tables.
OBJECT-TYPE    
  NonReplicated  

mscAtmIfVptIispSigVcd 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2
OBJECT IDENTIFIER    

mscAtmIfVptIispSigVcdRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.1
This entry controls the addition and deletion of mscAtmIfVptIispSigVcd components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispSigVcdRowStatusEntry

mscAtmIfVptIispSigVcdRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.1.1
A single entry in the table represents a single mscAtmIfVptIispSigVcd component.
OBJECT-TYPE    
  MscAtmIfVptIispSigVcdRowStatusEntry  

mscAtmIfVptIispSigVcdRowStatus 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfVptIispSigVcd components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfVptIispSigVcdComponentName 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfVptIispSigVcdStorageType 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.1.1.4
This variable represents the storage type value for the mscAtmIfVptIispSigVcd tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfVptIispSigVcdIndex 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.1.1.10
This variable represents the index for the mscAtmIfVptIispSigVcd tables.
OBJECT-TYPE    
  NonReplicated  

mscAtmIfVptIispSigVcdProvTable 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10
This group contains the provisionable traffic attributes for a control channel.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispSigVcdProvEntry

mscAtmIfVptIispSigVcdProvEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1
An entry in the mscAtmIfVptIispSigVcdProvTable.
OBJECT-TYPE    
  MscAtmIfVptIispSigVcdProvEntry  

mscAtmIfVptIispSigVcdTrafficDescType 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1.1
This attribute specifies the type of traffic management which is applied to both the transmit and receive direction of this connection as defined in the ATM Forum. The trafficDescType determines the number and meaning of the parameters in the trafficDescParm attribute.
OBJECT-TYPE    
  INTEGER n3(3), n6(6), n7(7), n8(8)  

mscAtmIfVptIispSigVcdAtmServiceCategory 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1.3
This attribute specifies the ATM service category for both directions of the connection. The constantBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by CellTransfer Delay are assumed to be of significantly reduce value to the application. The rtVariableBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by CTD are assumed to be of significantly reduced value to the application. Real time VBR service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. Non-real time VBR service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications; that is, those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection.
OBJECT-TYPE    
  INTEGER unspecifiedBitRate(0), constantBitRate(1), rtVariableBitRate(2), nrtVariableBitRate(3)  

mscAtmIfVptIispSigVcdWeight 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1.4
This attribute specifies an override for the weight of this unshaped connection. This attribute is ignored for shaped connections, for ABR connections, for connections on a CQC-based ATM FP and basic VPTs. When the value is set to sameAsCa, the weight is determined by the weight policy attribute under the CA service category component for all but standard VPT VCCs. For standard VPT VCCs, the weight is determined by the VCC's service category, when the value is set to sameAsCa. When this attribute is set to a value from 1 to 4095, that value is used for the weight policy of this connection relative to other connections. For all but standard VPT VCCs, weight policy determines the proportion of transit cell opportunities which are allocated to this connection, compared to other connections in the same service category. For standard VPT VCCs, weight policy determines the proportion of transmit cell opportunities which are allocated to this connection, compared to other connections associated with the VPT. When the value is set to upToQueueLimit, the weight policy is limited only by the txQueueLimit. VALUES ( 0 = upToQueueLimit 65535 = sameAsCa )
OBJECT-TYPE    
  Unsigned32 0 | 1..4095 | 65535  

mscAtmIfVptIispSigVcdQosClass 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1.21
This attribute specifies the quality of service for both the forward and backward direction for this connection. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters.
OBJECT-TYPE    
  INTEGER n0(0), n1(1), n2(2), n3(3), n4(4)  

mscAtmIfVptIispSigVcdTrafficShaping 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1.50
This attribute specifies whether this connection uses traffic shaping when transmitting traffic to the ATM interface. When sameAsCa is selected, traffic shaping for this connection is based on the trafficShaping attribute of the connection's service category component under the AtmIf CA. If the service category has traffic shaping enabled, then traffic shaping is enabled for the connection. Note that enabling traffic shaping may have no effect under certain cases. These cases are listed in the description of the trafficShaping operational attribute, which is under the Vcc Tm and Vpc Tm components. When disabled is selected, traffic shaping for this connection is disabled.
OBJECT-TYPE    
  INTEGER disabled(1), sameAsCa(2)  

mscAtmIfVptIispSigVcdUnshapedTransmitQueueing 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1.60
This attribute only applies when this connection is unshaped. This attribute specifies the transmit queueing method for this connection if it is unshaped. Refer to the unshapedTransmitQueueing attribute under the AtmIf CA service category subcomponent for more details on the meaning of this attribute. When this attribute is set to sameAsCa, the transmit queueing method for the connection is based on the unshapedTransmitQueueing attribute of the connection's service category component under the ConnectionAdministrator. When this attribute is set to common, transmit traffic on this unshaped connection is destined for the common queue. The value sameAsInterface is for migration from previous software releases, but should no longer be used
OBJECT-TYPE    
  INTEGER common(1), sameAsCa(3)  

mscAtmIfVptIispSigVcdUsageParameterControl 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.10.1.70
This attribute specifies whether this connection enforces usage parameter control when receiving traffic from the ATM interface. When sameAsCa is selected, UPC for the connection is based on the usageParameterControl attribute of the connection's service category component under the ConnectionAdministrator. If the service category has UPC enabled, then UPC is enabled for the connection. Note that enabling UPC may have no effect under certain cases. These cases are listed in the description of the usageParameterControl operational attribute, which is under the Vcc Tm or Vpc Tm component. When disabled is selected, UPC for this connection is disabled. The value sameAsInterface is for migration from previous software releases, but should no longer be used
OBJECT-TYPE    
  INTEGER disabled(1), sameAsCa(2)  

mscAtmIfVptIispSigVcdTdpTable 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.387
This attribute is a vector of five traffic parameters whose meanings are defined by the trafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When trafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When trafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For trafficDescType 3 the traffic is shaped at the next rate less than the PCR. For trafficDescType 6, 7, and 8, the traffic is shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic is shaped at the next rate above the PCR.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispSigVcdTdpEntry

mscAtmIfVptIispSigVcdTdpEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.387.1
An entry in the mscAtmIfVptIispSigVcdTdpTable.
OBJECT-TYPE    
  MscAtmIfVptIispSigVcdTdpEntry  

mscAtmIfVptIispSigVcdTdpIndex 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.387.1.1
This variable represents the mscAtmIfVptIispSigVcdTdpTable specific index for the mscAtmIfVptIispSigVcdTdpTable.
OBJECT-TYPE    
  Integer32 1..5  

mscAtmIfVptIispSigVcdTdpValue 1.3.6.1.4.1.562.36.2.1.114.9.6.3.2.387.1.2
This variable represents an individual value for the mscAtmIfVptIispSigVcdTdpTable.
OBJECT-TYPE    
  Unsigned32 0..2147483647  

mscAtmIfVptIispSigProvTable 1.3.6.1.4.1.562.36.2.1.114.9.6.3.10
This attribute group contains the provisionable attributes for the Signalling component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispSigProvEntry

mscAtmIfVptIispSigProvEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.3.10.1
An entry in the mscAtmIfVptIispSigProvTable.
OBJECT-TYPE    
  MscAtmIfVptIispSigProvEntry  

mscAtmIfVptIispSigVci 1.3.6.1.4.1.562.36.2.1.114.9.6.3.10.1.1
This attribute specifies the signalling channel number.
OBJECT-TYPE    
  Unsigned32 0..65535  

mscAtmIfVptIispSigAddressConversion 1.3.6.1.4.1.562.36.2.1.114.9.6.3.10.1.2
This attribute specifies the address conversion on the outgoing signalling PDUs. The options are none, nativeE164, or nsap. The none option is the default and if this option is chosen then nothing is done to the address information element (IE) in the outgoing signalling message. If nativeE164 option is chosen, then only NSAP encapsulated E.164 addresses with zeros in the ESI are converted to native E.164 format in the outgoing signalling message. If the NSAP address is not encapsulated E.164 or the ESI field is not zeros and the nativeE164 option is chosen, then the call is cleared. If the nsap option is chosen, then native E.164 addresses are converted to NSAP E.164 with zeros in the ESI field; otherwise the address is in NSAP format and is not changed.
OBJECT-TYPE    
  INTEGER none(0), nativeE164(1), nsap(2)  

mscAtmIfVptIispSigOperatingMode 1.3.6.1.4.1.562.36.2.1.114.9.6.3.10.1.3
This attribute specifies the operating mode of the signaling channel. provisionedOnly indicates that only SPVCs and SPVPs are supported on the interface and SVCs are not supported. This value is permitted only on UNI interfaces. normal indicates that SVCs, SPVCs, and SPVPs are supported on the interface.
OBJECT-TYPE    
  INTEGER normal(0), provisionedOnly(1)  

mscAtmIfVptIispSigStateTable 1.3.6.1.4.1.562.36.2.1.114.9.6.3.11
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispSigStateEntry

mscAtmIfVptIispSigStateEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.3.11.1
An entry in the mscAtmIfVptIispSigStateTable.
OBJECT-TYPE    
  MscAtmIfVptIispSigStateEntry  

mscAtmIfVptIispSigAdminState 1.3.6.1.4.1.562.36.2.1.114.9.6.3.11.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscAtmIfVptIispSigOperationalState 1.3.6.1.4.1.562.36.2.1.114.9.6.3.11.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscAtmIfVptIispSigUsageState 1.3.6.1.4.1.562.36.2.1.114.9.6.3.11.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscAtmIfVptIispSigOperTable 1.3.6.1.4.1.562.36.2.1.114.9.6.3.12
This attribute contains the operational attributes for the AtmSignalling component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispSigOperEntry

mscAtmIfVptIispSigOperEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.3.12.1
An entry in the mscAtmIfVptIispSigOperTable.
OBJECT-TYPE    
  MscAtmIfVptIispSigOperEntry  

mscAtmIfVptIispSigLastTxCauseCode 1.3.6.1.4.1.562.36.2.1.114.9.6.3.12.1.1
This attribute indicates the cause code in the last transmitted signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
OBJECT-TYPE    
  Unsigned32 0..255  

mscAtmIfVptIispSigLastTxDiagCode 1.3.6.1.4.1.562.36.2.1.114.9.6.3.12.1.2
This attribute contains the diagnostic code in the last transmitted signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
OBJECT-TYPE    
  Hex 0..255  

mscAtmIfVptIispSigLastRxCauseCode 1.3.6.1.4.1.562.36.2.1.114.9.6.3.12.1.3
This attribute contains the cause code in the last received signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
OBJECT-TYPE    
  Unsigned32 0..255  

mscAtmIfVptIispSigLastRxDiagCode 1.3.6.1.4.1.562.36.2.1.114.9.6.3.12.1.4
This attribute contains the diagnostic code in the last received signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
OBJECT-TYPE    
  Hex 0..255  

mscAtmIfVptIispSigStatsTable 1.3.6.1.4.1.562.36.2.1.114.9.6.3.13
This attribute group contains the statistics associated with the AtmSignalling component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispSigStatsEntry

mscAtmIfVptIispSigStatsEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1
An entry in the mscAtmIfVptIispSigStatsTable.
OBJECT-TYPE    
  MscAtmIfVptIispSigStatsEntry  

mscAtmIfVptIispSigCurrentConnections 1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.1
This attribute indicates the total number of currently active connections.
OBJECT-TYPE    
  Counter32  

mscAtmIfVptIispSigPeakConnections 1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.2
This attribute indicates the high water mark of active point-to- point and point-to-multipoint connections.
OBJECT-TYPE    
  Gauge32 0..4294967295  

mscAtmIfVptIispSigSuccessfulConnections 1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.3
This attribute counts the total number of switched point-to- point and point-to-multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
OBJECT-TYPE    
  Counter32  

mscAtmIfVptIispSigFailedConnections 1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.4
This attribute counts the total number of switched connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
OBJECT-TYPE    
  Counter32  

mscAtmIfVptIispSigTxPdus 1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.5
This attribute counts the number of transmitted signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
OBJECT-TYPE    
  Counter32  

mscAtmIfVptIispSigRxPdus 1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.6
This attribute counts the number of received signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
OBJECT-TYPE    
  Counter32  

mscAtmIfVptIispSigCurrentPmpConnections 1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.7
This attribute indicates the number of currently active point-to- multipoint connections.
OBJECT-TYPE    
  Gauge32 0..4294967295  

mscAtmIfVptIispSigPeakPmpConnections 1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.8
This attribute indicates the high water mark of active point-to- multipoint connections.
OBJECT-TYPE    
  Gauge32 0..4294967295  

mscAtmIfVptIispSigSuccessfulPmpConnections 1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.9
This attribute counts the total number of switched point-to- multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
OBJECT-TYPE    
  Counter32  

mscAtmIfVptIispSigFailedPmpConnections 1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.10
This attribute counts the number of switched point-to- multipoint connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
OBJECT-TYPE    
  Counter32  

mscAtmIfVptIispSigNewCurrentConnections 1.3.6.1.4.1.562.36.2.1.114.9.6.3.13.1.11
This attribute indicates the total number of currently active point-to- point and point-to-multipoint connections.
OBJECT-TYPE    
  Gauge32 0..4294967295  

mscAtmIfVptIispAddr 1.3.6.1.4.1.562.36.2.1.114.9.6.4
OBJECT IDENTIFIER    

mscAtmIfVptIispAddrRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.9.6.4.1
This entry controls the addition and deletion of mscAtmIfVptIispAddr components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispAddrRowStatusEntry

mscAtmIfVptIispAddrRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.4.1.1
A single entry in the table represents a single mscAtmIfVptIispAddr component.
OBJECT-TYPE    
  MscAtmIfVptIispAddrRowStatusEntry  

mscAtmIfVptIispAddrRowStatus 1.3.6.1.4.1.562.36.2.1.114.9.6.4.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfVptIispAddr components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfVptIispAddrComponentName 1.3.6.1.4.1.562.36.2.1.114.9.6.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfVptIispAddrStorageType 1.3.6.1.4.1.562.36.2.1.114.9.6.4.1.1.4
This variable represents the storage type value for the mscAtmIfVptIispAddr tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfVptIispAddrAddressIndex 1.3.6.1.4.1.562.36.2.1.114.9.6.4.1.1.10
This variable represents an index for the mscAtmIfVptIispAddr tables.
OBJECT-TYPE    
  AsciiStringIndex SIZE(1..40)  

mscAtmIfVptIispAddrAddressTypeIndex 1.3.6.1.4.1.562.36.2.1.114.9.6.4.1.1.11
This variable represents an index for the mscAtmIfVptIispAddr tables.
OBJECT-TYPE    
  INTEGER primary(0), alternate(1), default(3)  

mscAtmIfVptIispAddrTermSP 1.3.6.1.4.1.562.36.2.1.114.9.6.4.2
OBJECT IDENTIFIER    

mscAtmIfVptIispAddrTermSPRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.9.6.4.2.1
This entry controls the addition and deletion of mscAtmIfVptIispAddrTermSP components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispAddrTermSPRowStatusEntry

mscAtmIfVptIispAddrTermSPRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.4.2.1.1
A single entry in the table represents a single mscAtmIfVptIispAddrTermSP component.
OBJECT-TYPE    
  MscAtmIfVptIispAddrTermSPRowStatusEntry  

mscAtmIfVptIispAddrTermSPRowStatus 1.3.6.1.4.1.562.36.2.1.114.9.6.4.2.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfVptIispAddrTermSP components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfVptIispAddrTermSPComponentName 1.3.6.1.4.1.562.36.2.1.114.9.6.4.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfVptIispAddrTermSPStorageType 1.3.6.1.4.1.562.36.2.1.114.9.6.4.2.1.1.4
This variable represents the storage type value for the mscAtmIfVptIispAddrTermSP tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfVptIispAddrTermSPIndex 1.3.6.1.4.1.562.36.2.1.114.9.6.4.2.1.1.10
This variable represents the index for the mscAtmIfVptIispAddrTermSP tables.
OBJECT-TYPE    
  NonReplicated  

mscAtmIfVptIispAddrPnniInfo 1.3.6.1.4.1.562.36.2.1.114.9.6.4.3
OBJECT IDENTIFIER    

mscAtmIfVptIispAddrPnniInfoRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.1
This entry controls the addition and deletion of mscAtmIfVptIispAddrPnniInfo components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispAddrPnniInfoRowStatusEntry

mscAtmIfVptIispAddrPnniInfoRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.1.1
A single entry in the table represents a single mscAtmIfVptIispAddrPnniInfo component.
OBJECT-TYPE    
  MscAtmIfVptIispAddrPnniInfoRowStatusEntry  

mscAtmIfVptIispAddrPnniInfoRowStatus 1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfVptIispAddrPnniInfo components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfVptIispAddrPnniInfoComponentName 1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfVptIispAddrPnniInfoStorageType 1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.1.1.4
This variable represents the storage type value for the mscAtmIfVptIispAddrPnniInfo tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfVptIispAddrPnniInfoIndex 1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.1.1.10
This variable represents the index for the mscAtmIfVptIispAddrPnniInfo tables.
OBJECT-TYPE    
  NonReplicated  

mscAtmIfVptIispAddrPnniInfoProvTable 1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.10
This attribute group contains the provisioned attributes relating to PNNI for a PnniInfo component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispAddrPnniInfoProvEntry

mscAtmIfVptIispAddrPnniInfoProvEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.10.1
An entry in the mscAtmIfVptIispAddrPnniInfoProvTable.
OBJECT-TYPE    
  MscAtmIfVptIispAddrPnniInfoProvEntry  

mscAtmIfVptIispAddrPnniInfoScope 1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.10.1.1
This attribute specifies the scope of the ATM address, which is the highest level up to which this address will be advertised in the PNNI hierarchy. The scope must be set to a value numerically less than or equal to the level of the lowest level peer group containing this node. Setting the scope to 0 will cause the address to be advertised globally within this PNNI routing domain.
OBJECT-TYPE    
  INTEGER -1..104  

mscAtmIfVptIispAddrPnniInfoReachability 1.3.6.1.4.1.562.36.2.1.114.9.6.4.3.10.1.2
This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
OBJECT-TYPE    
  INTEGER internal(0), exterior(1)  

mscAtmIfVptIispAddrOperTable 1.3.6.1.4.1.562.36.2.1.114.9.6.4.10
This attribute group contains the operational attributes for the Address component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispAddrOperEntry

mscAtmIfVptIispAddrOperEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.4.10.1
An entry in the mscAtmIfVptIispAddrOperTable.
OBJECT-TYPE    
  MscAtmIfVptIispAddrOperEntry  

mscAtmIfVptIispAddrScope 1.3.6.1.4.1.562.36.2.1.114.9.6.4.10.1.1
This attribute indicates the scope of the ATM address, which is the highest level to which this address will be advertised in the PNNI hierarchy. If no PnniInfo subcomponent has been provisioned, then the scope will default to the level of this node in the PNNI hierarchy. If this node does not participate in a PNNI hierarchy, then this attribute will have the value of -1.
OBJECT-TYPE    
  INTEGER -1..104  

mscAtmIfVptIispAddrReachability 1.3.6.1.4.1.562.36.2.1.114.9.6.4.10.1.2
This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
OBJECT-TYPE    
  INTEGER internal(0), exterior(1)  

mscAtmIfVptIispCallingAScr 1.3.6.1.4.1.562.36.2.1.114.9.6.5
OBJECT IDENTIFIER    

mscAtmIfVptIispCallingAScrRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.9.6.5.1
This entry controls the addition and deletion of mscAtmIfVptIispCallingAScr components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispCallingAScrRowStatusEntry

mscAtmIfVptIispCallingAScrRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.5.1.1
A single entry in the table represents a single mscAtmIfVptIispCallingAScr component.
OBJECT-TYPE    
  MscAtmIfVptIispCallingAScrRowStatusEntry  

mscAtmIfVptIispCallingAScrRowStatus 1.3.6.1.4.1.562.36.2.1.114.9.6.5.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfVptIispCallingAScr components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfVptIispCallingAScrComponentName 1.3.6.1.4.1.562.36.2.1.114.9.6.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfVptIispCallingAScrStorageType 1.3.6.1.4.1.562.36.2.1.114.9.6.5.1.1.4
This variable represents the storage type value for the mscAtmIfVptIispCallingAScr tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfVptIispCallingAScrIndex 1.3.6.1.4.1.562.36.2.1.114.9.6.5.1.1.10
This variable represents the index for the mscAtmIfVptIispCallingAScr tables.
OBJECT-TYPE    
  NonReplicated  

mscAtmIfVptIispCallingAScrAddr 1.3.6.1.4.1.562.36.2.1.114.9.6.5.2
OBJECT IDENTIFIER    

mscAtmIfVptIispCallingAScrAddrRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.9.6.5.2.1
This entry controls the addition and deletion of mscAtmIfVptIispCallingAScrAddr components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispCallingAScrAddrRowStatusEntry

mscAtmIfVptIispCallingAScrAddrRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.5.2.1.1
A single entry in the table represents a single mscAtmIfVptIispCallingAScrAddr component.
OBJECT-TYPE    
  MscAtmIfVptIispCallingAScrAddrRowStatusEntry  

mscAtmIfVptIispCallingAScrAddrRowStatus 1.3.6.1.4.1.562.36.2.1.114.9.6.5.2.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfVptIispCallingAScrAddr components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfVptIispCallingAScrAddrComponentName 1.3.6.1.4.1.562.36.2.1.114.9.6.5.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfVptIispCallingAScrAddrStorageType 1.3.6.1.4.1.562.36.2.1.114.9.6.5.2.1.1.4
This variable represents the storage type value for the mscAtmIfVptIispCallingAScrAddr tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfVptIispCallingAScrAddrAddressIndex 1.3.6.1.4.1.562.36.2.1.114.9.6.5.2.1.1.10
This variable represents an index for the mscAtmIfVptIispCallingAScrAddr tables.
OBJECT-TYPE    
  AsciiStringIndex SIZE(1..40)  

mscAtmIfVptIispCallingAScrAddrAddressActionIndex 1.3.6.1.4.1.562.36.2.1.114.9.6.5.2.1.1.11
This variable represents an index for the mscAtmIfVptIispCallingAScrAddr tables.
OBJECT-TYPE    
  INTEGER accept(0), reject(1)  

mscAtmIfVptIispCallingAScrProvTable 1.3.6.1.4.1.562.36.2.1.114.9.6.5.10
This attribute group contains the provisionable attributes for the CallingAScr component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispCallingAScrProvEntry

mscAtmIfVptIispCallingAScrProvEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.5.10.1
An entry in the mscAtmIfVptIispCallingAScrProvTable.
OBJECT-TYPE    
  MscAtmIfVptIispCallingAScrProvEntry  

mscAtmIfVptIispCallingAScrAdminStatus 1.3.6.1.4.1.562.36.2.1.114.9.6.5.10.1.1
This attribute specifies whether the calling address screening feature is enabled or disabled. If enabled, incoming SVC calls are screened against provisioned addresses. If enabled and the calling address in the ATM SVC call request is provisioned to be accepted, the call is accepted or rejected according to the action specified for that address. If the value is enabled, and the calling address in the address request is not provisioned, the call is rejected If the value is disabled, no calling address screening is performed.
OBJECT-TYPE    
  INTEGER enabled(0), disabled(1)  

mscAtmIfVptIispCallingAScrDefaultInsertionAddress 1.3.6.1.4.1.562.36.2.1.114.9.6.5.10.1.2
This attribute specifies the address to be inserted into the SVC connection request if adminStatus is enabled and the connection request does not contain a calling address. If the adminStatus attribute is enabled and this attribute is empty, all incoming SVC calls which do not contain a calling address are rejected.
OBJECT-TYPE    
  HexString SIZE(0..20)  

mscAtmIfVptIispCallingAScrStatTable 1.3.6.1.4.1.562.36.2.1.114.9.6.5.11
This attribute group contains statistics related to the incoming SVC call requests received while the adminStatus attribute is set to enabled.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispCallingAScrStatEntry

mscAtmIfVptIispCallingAScrStatEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.5.11.1
An entry in the mscAtmIfVptIispCallingAScrStatTable.
OBJECT-TYPE    
  MscAtmIfVptIispCallingAScrStatEntry  

mscAtmIfVptIispCallingAScrAcceptedCalls 1.3.6.1.4.1.562.36.2.1.114.9.6.5.11.1.1
This attribute counts the incoming SVC calls which were accepted because the address specified in the call request matched a provisioned ATM address and the associated action was accept. When the counter exceeds the maximum, it wraps to 0.
OBJECT-TYPE    
  Counter32  

mscAtmIfVptIispCallingAScrRejectedCalls 1.3.6.1.4.1.562.36.2.1.114.9.6.5.11.1.2
This attribute counts the incoming SVC calls which were rejected because the address specified in the call request matched a provisioned ATM address, but the associated action was reject. When the counter exceeds the maximum, it wraps to 0.
OBJECT-TYPE    
  Counter32  

mscAtmIfVptIispCallingAScrUnmatchedCalls 1.3.6.1.4.1.562.36.2.1.114.9.6.5.11.1.3
This attribute counts the incoming SVC calls which were rejected because none of the provisioned ATM addresses matched the applicable address in the incoming SVC call request. When the counter exceeds the maximum, it wraps to 0.
OBJECT-TYPE    
  Counter32  

mscAtmIfVptIispCalledAScr 1.3.6.1.4.1.562.36.2.1.114.9.6.6
OBJECT IDENTIFIER    

mscAtmIfVptIispCalledAScrRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.9.6.6.1
This entry controls the addition and deletion of mscAtmIfVptIispCalledAScr components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispCalledAScrRowStatusEntry

mscAtmIfVptIispCalledAScrRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.6.1.1
A single entry in the table represents a single mscAtmIfVptIispCalledAScr component.
OBJECT-TYPE    
  MscAtmIfVptIispCalledAScrRowStatusEntry  

mscAtmIfVptIispCalledAScrRowStatus 1.3.6.1.4.1.562.36.2.1.114.9.6.6.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfVptIispCalledAScr components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfVptIispCalledAScrComponentName 1.3.6.1.4.1.562.36.2.1.114.9.6.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfVptIispCalledAScrStorageType 1.3.6.1.4.1.562.36.2.1.114.9.6.6.1.1.4
This variable represents the storage type value for the mscAtmIfVptIispCalledAScr tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfVptIispCalledAScrIndex 1.3.6.1.4.1.562.36.2.1.114.9.6.6.1.1.10
This variable represents the index for the mscAtmIfVptIispCalledAScr tables.
OBJECT-TYPE    
  NonReplicated  

mscAtmIfVptIispCalledAScrAddr 1.3.6.1.4.1.562.36.2.1.114.9.6.6.2
OBJECT IDENTIFIER    

mscAtmIfVptIispCalledAScrAddrRowStatusTable 1.3.6.1.4.1.562.36.2.1.114.9.6.6.2.1
This entry controls the addition and deletion of mscAtmIfVptIispCalledAScrAddr components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispCalledAScrAddrRowStatusEntry

mscAtmIfVptIispCalledAScrAddrRowStatusEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.6.2.1.1
A single entry in the table represents a single mscAtmIfVptIispCalledAScrAddr component.
OBJECT-TYPE    
  MscAtmIfVptIispCalledAScrAddrRowStatusEntry  

mscAtmIfVptIispCalledAScrAddrRowStatus 1.3.6.1.4.1.562.36.2.1.114.9.6.6.2.1.1.1
This variable is used as the basis for SNMP naming of mscAtmIfVptIispCalledAScrAddr components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscAtmIfVptIispCalledAScrAddrComponentName 1.3.6.1.4.1.562.36.2.1.114.9.6.6.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscAtmIfVptIispCalledAScrAddrStorageType 1.3.6.1.4.1.562.36.2.1.114.9.6.6.2.1.1.4
This variable represents the storage type value for the mscAtmIfVptIispCalledAScrAddr tables.
OBJECT-TYPE    
  StorageType  

mscAtmIfVptIispCalledAScrAddrAddressIndex 1.3.6.1.4.1.562.36.2.1.114.9.6.6.2.1.1.10
This variable represents an index for the mscAtmIfVptIispCalledAScrAddr tables.
OBJECT-TYPE    
  AsciiStringIndex SIZE(1..40)  

mscAtmIfVptIispCalledAScrAddrAddressActionIndex 1.3.6.1.4.1.562.36.2.1.114.9.6.6.2.1.1.11
This variable represents an index for the mscAtmIfVptIispCalledAScrAddr tables.
OBJECT-TYPE    
  INTEGER accept(0), reject(1)  

mscAtmIfVptIispCalledAScrProvTable 1.3.6.1.4.1.562.36.2.1.114.9.6.6.10
This attribute group contains the provisionable attributes for the CalledAScr component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispCalledAScrProvEntry

mscAtmIfVptIispCalledAScrProvEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.6.10.1
An entry in the mscAtmIfVptIispCalledAScrProvTable.
OBJECT-TYPE    
  MscAtmIfVptIispCalledAScrProvEntry  

mscAtmIfVptIispCalledAScrAdminStatus 1.3.6.1.4.1.562.36.2.1.114.9.6.6.10.1.1
This attribute specifies whether the called address screening feature is enabled or disabled. If the value is enabled, incoming SVC calls will be screened against provisioned called addresses. If the value is enabled and the called address in the ATM SVC call request has been provisioned, the call is accepted or rejected according to the action specified for that address. If the value is enabled and the called address in the call request is not provisioned, the call is rejected. If the value is disabled, no called address screening is performed.
OBJECT-TYPE    
  INTEGER enabled(0), disabled(1)  

mscAtmIfVptIispCalledAScrStatTable 1.3.6.1.4.1.562.36.2.1.114.9.6.6.11
This attribute group contains statistics related to the incoming SVC call requests received while the adminStatus attribute is set to enabled.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispCalledAScrStatEntry

mscAtmIfVptIispCalledAScrStatEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.6.11.1
An entry in the mscAtmIfVptIispCalledAScrStatTable.
OBJECT-TYPE    
  MscAtmIfVptIispCalledAScrStatEntry  

mscAtmIfVptIispCalledAScrAcceptedCalls 1.3.6.1.4.1.562.36.2.1.114.9.6.6.11.1.1
This attribute counts the incoming SVC calls which were accepted because the address specified in the call request matched a provisioned ATM address and the associated action was accept. When the counter exceeds the maximum, it wraps to 0.
OBJECT-TYPE    
  Counter32  

mscAtmIfVptIispCalledAScrRejectedCalls 1.3.6.1.4.1.562.36.2.1.114.9.6.6.11.1.2
This attribute counts the incoming SVC calls which were rejected because the address specified in the call request matched a provisioned ATM address, but the associated action was reject. When the counter exceeds the maximum, it wraps to 0.
OBJECT-TYPE    
  Counter32  

mscAtmIfVptIispCalledAScrUnmatchedCalls 1.3.6.1.4.1.562.36.2.1.114.9.6.6.11.1.3
This attribute counts the incoming SVC calls which were rejected because none of the provisioned ATM addresses matched the applicable address in the incoming SVC call request. When the counter exceeds the maximum, it wraps to 0.
OBJECT-TYPE    
  Counter32  

mscAtmIfVptIispProvTable 1.3.6.1.4.1.562.36.2.1.114.9.6.10
This group contains the provisionable attributes for the Iisp component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispProvEntry

mscAtmIfVptIispProvEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.10.1
An entry in the mscAtmIfVptIispProvTable.
OBJECT-TYPE    
  MscAtmIfVptIispProvEntry  

mscAtmIfVptIispVersion 1.3.6.1.4.1.562.36.2.1.114.9.6.10.1.1
This attribute indicates which specification the IISP interface complies with. The options are iisp10Sig30 which refers to IISP version 1.0 with 3.0 signalling and iisp10Sig31 which refers to IISP version 1.0 with 3.1 signalling. If this attribute is changed, all switched Vcc components in this interface are cleared due to the fact that the two versions are incompatible.
OBJECT-TYPE    
  INTEGER iisp10Sig30(2), iisp10Sig31(3)  

mscAtmIfVptIispSide 1.3.6.1.4.1.562.36.2.1.114.9.6.10.1.2
This attribute indicates which side the interface is, user or network.
OBJECT-TYPE    
  INTEGER networkSide(0), userSide(1)  

mscAtmIfVptIispSoftPvcRetryPeriod 1.3.6.1.4.1.562.36.2.1.114.9.6.10.1.3
This attribute specifies the time to wait between call set up retries. The resolution is to the nearest 10 seconds. This attribute has been obsoleted and is replaced by the softPvpAndPvcRetryPeriod attribute.
OBJECT-TYPE    
  Unsigned32 20..999999  

mscAtmIfVptIispSoftPvpAndPvcRetryPeriod 1.3.6.1.4.1.562.36.2.1.114.9.6.10.1.4
This attribute specifies the time to wait between soft PVP or soft PVC call setup retries. The resolution is to the nearest 10 seconds.
OBJECT-TYPE    
  Unsigned32 20..999999  

mscAtmIfVptIispSoftPvpAndPvcHoldOffTime 1.3.6.1.4.1.562.36.2.1.114.9.6.10.1.5
This attribute specifies how long to hold off retries following a release or the connection. The resolution is to the nearest 50 ms.
OBJECT-TYPE    
  Unsigned32 0 | 50..20000  

mscAtmIfVptIispAcctOptTable 1.3.6.1.4.1.562.36.2.1.114.9.6.11
This group contains the provisionable attributes for accounting.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispAcctOptEntry

mscAtmIfVptIispAcctOptEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.11.1
An entry in the mscAtmIfVptIispAcctOptTable.
OBJECT-TYPE    
  MscAtmIfVptIispAcctOptEntry  

mscAtmIfVptIispAccountCollection 1.3.6.1.4.1.562.36.2.1.114.9.6.11.1.1
This attribute is used to turn accounting on or off for SVC and SPVC connections. It also specifies the reason(s) for which accounting data is collected: billing, test, study, audit, or force. If the set of reasons is not empty then accounting records will be generated by this interface in the following situations: - on a TODA changeover if TODA is enabled; - every 12 hours (per connection) if TODA is disabled; - on every call clear (a call record with final cell counts). If none of the reasons is present, then accounting will be suppressed. The reason for collection is recorded in the accounting record, in the attribute callingCollectReason or calledCollectReason as appropriate. Description of bits: bill(0) test(1) study(2) audit(3) force(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscAtmIfVptIispAccountConnectionType 1.3.6.1.4.1.562.36.2.1.114.9.6.11.1.2
This attribute specifies whether accounting records generated by this interface should be marked as originating, terminating or intermediate. This attribute, in combination with the direction of the call, determines the value of attribute connPointType of the accounting record and may be used by downstream accounting processes to correlate the records. If the value is origTerm then records generated for incoming calls will be marked as originating and records generated for outgoing calls will be marked as terminating. If the value is intermediate then records generated for all calls will be marked as intermediate.
OBJECT-TYPE    
  INTEGER origTerm(0), intermediate(1)  

mscAtmIfVptIispAccountClass 1.3.6.1.4.1.562.36.2.1.114.9.6.11.1.3
This attribute specifies the accounting class associated with the interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingServiceType or calledServiceType as appropriate.
OBJECT-TYPE    
  Unsigned32 0..255  

mscAtmIfVptIispServiceExchange 1.3.6.1.4.1.562.36.2.1.114.9.6.11.1.4
This attribute specifies the data service exchange associated with this interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingDse or calledDse as appropriate.
OBJECT-TYPE    
  Unsigned32 0..255  

mscAtmIfVptIispVProvTable 1.3.6.1.4.1.562.36.2.1.114.9.6.12
This group contains the provisionable attributes for the Iisp component which are specific to virtual IISP interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    MscAtmIfVptIispVProvEntry

mscAtmIfVptIispVProvEntry 1.3.6.1.4.1.562.36.2.1.114.9.6.12.1
An entry in the mscAtmIfVptIispVProvTable.
OBJECT-TYPE    
  MscAtmIfVptIispVProvEntry  

mscAtmIfVptIispVpci 1.3.6.1.4.1.562.36.2.1.114.9.6.12.1.1
This attribute specifies the Virtual Path Connection Identifier (VPCI) to be used between this signalling entity and its peer. The VPCI of the peer virtual IISP must have the same value for switched connections to be set up across the interface.
OBJECT-TYPE    
  Unsigned32 0..255  

atmIispMIB 1.3.6.1.4.1.562.36.2.2.70
OBJECT IDENTIFIER    

atmIispGroup 1.3.6.1.4.1.562.36.2.2.70.1
OBJECT IDENTIFIER    

atmIispGroupCA 1.3.6.1.4.1.562.36.2.2.70.1.1
OBJECT IDENTIFIER    

atmIispGroupCA02 1.3.6.1.4.1.562.36.2.2.70.1.1.3
OBJECT IDENTIFIER    

atmIispGroupCA02A 1.3.6.1.4.1.562.36.2.2.70.1.1.3.2
OBJECT IDENTIFIER    

atmIispCapabilities 1.3.6.1.4.1.562.36.2.2.70.3
OBJECT IDENTIFIER    

atmIispCapabilitiesCA 1.3.6.1.4.1.562.36.2.2.70.3.1
OBJECT IDENTIFIER    

atmIispCapabilitiesCA02 1.3.6.1.4.1.562.36.2.2.70.3.1.3
OBJECT IDENTIFIER    

atmIispCapabilitiesCA02A 1.3.6.1.4.1.562.36.2.2.70.3.1.3.2
OBJECT IDENTIFIER    

Defined Objects

MscAtmIfIispRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfIispRowStatus  
  DisplayString as mscAtmIfIispComponentName  
  StorageType as mscAtmIfIispStorageType  
  NonReplicated as mscAtmIfIispIndex  

MscAtmIfIispProvEntry  
SEQUENCE    
  INTEGER as mscAtmIfIispVersion  
  INTEGER as mscAtmIfIispSide  
  Unsigned32 as mscAtmIfIispSoftPvcRetryPeriod  
  Unsigned32 as mscAtmIfIispSoftPvpAndPvcRetryPeriod  
  Unsigned32 as mscAtmIfIispSoftPvpAndPvcHoldOffTime  

MscAtmIfIispAcctOptEntry  
SEQUENCE    
  OCTET STRING as mscAtmIfIispAccountCollection  
  INTEGER as mscAtmIfIispAccountConnectionType  
  Unsigned32 as mscAtmIfIispAccountClass  
  Unsigned32 as mscAtmIfIispServiceExchange  

MscAtmIfIispSigRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfIispSigRowStatus  
  DisplayString as mscAtmIfIispSigComponentName  
  StorageType as mscAtmIfIispSigStorageType  
  NonReplicated as mscAtmIfIispSigIndex  

MscAtmIfIispSigProvEntry  
SEQUENCE    
  Unsigned32 as mscAtmIfIispSigVci  
  INTEGER as mscAtmIfIispSigAddressConversion  
  INTEGER as mscAtmIfIispSigOperatingMode  

MscAtmIfIispSigStateEntry  
SEQUENCE    
  INTEGER as mscAtmIfIispSigAdminState  
  INTEGER as mscAtmIfIispSigOperationalState  
  INTEGER as mscAtmIfIispSigUsageState  

MscAtmIfIispSigOperEntry  
SEQUENCE    
  Unsigned32 as mscAtmIfIispSigLastTxCauseCode  
  Hex as mscAtmIfIispSigLastTxDiagCode  
  Unsigned32 as mscAtmIfIispSigLastRxCauseCode  
  Hex as mscAtmIfIispSigLastRxDiagCode  

MscAtmIfIispSigStatsEntry  
SEQUENCE    
  Counter32 as mscAtmIfIispSigCurrentConnections  
  Gauge32 as mscAtmIfIispSigPeakConnections  
  Counter32 as mscAtmIfIispSigSuccessfulConnections  
  Counter32 as mscAtmIfIispSigFailedConnections  
  Counter32 as mscAtmIfIispSigTxPdus  
  Counter32 as mscAtmIfIispSigRxPdus  
  Gauge32 as mscAtmIfIispSigCurrentPmpConnections  
  Gauge32 as mscAtmIfIispSigPeakPmpConnections  
  Counter32 as mscAtmIfIispSigSuccessfulPmpConnections  
  Counter32 as mscAtmIfIispSigFailedPmpConnections  
  Gauge32 as mscAtmIfIispSigNewCurrentConnections  

MscAtmIfIispSigVcdRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfIispSigVcdRowStatus  
  DisplayString as mscAtmIfIispSigVcdComponentName  
  StorageType as mscAtmIfIispSigVcdStorageType  
  NonReplicated as mscAtmIfIispSigVcdIndex  

MscAtmIfIispSigVcdProvEntry  
SEQUENCE    
  INTEGER as mscAtmIfIispSigVcdTrafficDescType  
  INTEGER as mscAtmIfIispSigVcdAtmServiceCategory  
  Unsigned32 as mscAtmIfIispSigVcdWeight  
  INTEGER as mscAtmIfIispSigVcdQosClass  
  INTEGER as mscAtmIfIispSigVcdTrafficShaping  
  INTEGER as mscAtmIfIispSigVcdUnshapedTransmitQueueing  
  INTEGER as mscAtmIfIispSigVcdUsageParameterControl  

MscAtmIfIispSigVcdTdpEntry  
SEQUENCE    
  Integer32 as mscAtmIfIispSigVcdTdpIndex  
  Unsigned32 as mscAtmIfIispSigVcdTdpValue  

MscAtmIfIispAddrRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfIispAddrRowStatus  
  DisplayString as mscAtmIfIispAddrComponentName  
  StorageType as mscAtmIfIispAddrStorageType  
  AsciiStringIndex as mscAtmIfIispAddrAddressIndex  
  INTEGER as mscAtmIfIispAddrAddressTypeIndex  

MscAtmIfIispAddrOperEntry  
SEQUENCE    
  INTEGER as mscAtmIfIispAddrScope  
  INTEGER as mscAtmIfIispAddrReachability  

MscAtmIfIispAddrTermSPRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfIispAddrTermSPRowStatus  
  DisplayString as mscAtmIfIispAddrTermSPComponentName  
  StorageType as mscAtmIfIispAddrTermSPStorageType  
  NonReplicated as mscAtmIfIispAddrTermSPIndex  

MscAtmIfIispAddrPnniInfoRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfIispAddrPnniInfoRowStatus  
  DisplayString as mscAtmIfIispAddrPnniInfoComponentName  
  StorageType as mscAtmIfIispAddrPnniInfoStorageType  
  NonReplicated as mscAtmIfIispAddrPnniInfoIndex  

MscAtmIfIispAddrPnniInfoProvEntry  
SEQUENCE    
  INTEGER as mscAtmIfIispAddrPnniInfoScope  
  INTEGER as mscAtmIfIispAddrPnniInfoReachability  

MscAtmIfIispCallingAScrRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfIispCallingAScrRowStatus  
  DisplayString as mscAtmIfIispCallingAScrComponentName  
  StorageType as mscAtmIfIispCallingAScrStorageType  
  NonReplicated as mscAtmIfIispCallingAScrIndex  

MscAtmIfIispCallingAScrProvEntry  
SEQUENCE    
  INTEGER as mscAtmIfIispCallingAScrAdminStatus  
  HexString as mscAtmIfIispCallingAScrDefaultInsertionAddress  

MscAtmIfIispCallingAScrStatEntry  
SEQUENCE    
  Counter32 as mscAtmIfIispCallingAScrAcceptedCalls  
  Counter32 as mscAtmIfIispCallingAScrRejectedCalls  
  Counter32 as mscAtmIfIispCallingAScrUnmatchedCalls  

MscAtmIfIispCallingAScrAddrRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfIispCallingAScrAddrRowStatus  
  DisplayString as mscAtmIfIispCallingAScrAddrComponentName  
  StorageType as mscAtmIfIispCallingAScrAddrStorageType  
  AsciiStringIndex as mscAtmIfIispCallingAScrAddrAddressIndex  
  INTEGER as mscAtmIfIispCallingAScrAddrAddressActionIndex  

MscAtmIfIispCalledAScrRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfIispCalledAScrRowStatus  
  DisplayString as mscAtmIfIispCalledAScrComponentName  
  StorageType as mscAtmIfIispCalledAScrStorageType  
  NonReplicated as mscAtmIfIispCalledAScrIndex  

MscAtmIfIispCalledAScrProvEntry  
SEQUENCE    
  INTEGER as mscAtmIfIispCalledAScrAdminStatus  

MscAtmIfIispCalledAScrStatEntry  
SEQUENCE    
  Counter32 as mscAtmIfIispCalledAScrAcceptedCalls  
  Counter32 as mscAtmIfIispCalledAScrRejectedCalls  
  Counter32 as mscAtmIfIispCalledAScrUnmatchedCalls  

MscAtmIfIispCalledAScrAddrRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfIispCalledAScrAddrRowStatus  
  DisplayString as mscAtmIfIispCalledAScrAddrComponentName  
  StorageType as mscAtmIfIispCalledAScrAddrStorageType  
  AsciiStringIndex as mscAtmIfIispCalledAScrAddrAddressIndex  
  INTEGER as mscAtmIfIispCalledAScrAddrAddressActionIndex  

MscAtmIfVptIispRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfVptIispRowStatus  
  DisplayString as mscAtmIfVptIispComponentName  
  StorageType as mscAtmIfVptIispStorageType  
  NonReplicated as mscAtmIfVptIispIndex  

MscAtmIfVptIispProvEntry  
SEQUENCE    
  INTEGER as mscAtmIfVptIispVersion  
  INTEGER as mscAtmIfVptIispSide  
  Unsigned32 as mscAtmIfVptIispSoftPvcRetryPeriod  
  Unsigned32 as mscAtmIfVptIispSoftPvpAndPvcRetryPeriod  
  Unsigned32 as mscAtmIfVptIispSoftPvpAndPvcHoldOffTime  

MscAtmIfVptIispAcctOptEntry  
SEQUENCE    
  OCTET STRING as mscAtmIfVptIispAccountCollection  
  INTEGER as mscAtmIfVptIispAccountConnectionType  
  Unsigned32 as mscAtmIfVptIispAccountClass  
  Unsigned32 as mscAtmIfVptIispServiceExchange  

MscAtmIfVptIispVProvEntry  
SEQUENCE    
  Unsigned32 as mscAtmIfVptIispVpci  

MscAtmIfVptIispSigRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfVptIispSigRowStatus  
  DisplayString as mscAtmIfVptIispSigComponentName  
  StorageType as mscAtmIfVptIispSigStorageType  
  NonReplicated as mscAtmIfVptIispSigIndex  

MscAtmIfVptIispSigProvEntry  
SEQUENCE    
  Unsigned32 as mscAtmIfVptIispSigVci  
  INTEGER as mscAtmIfVptIispSigAddressConversion  
  INTEGER as mscAtmIfVptIispSigOperatingMode  

MscAtmIfVptIispSigStateEntry  
SEQUENCE    
  INTEGER as mscAtmIfVptIispSigAdminState  
  INTEGER as mscAtmIfVptIispSigOperationalState  
  INTEGER as mscAtmIfVptIispSigUsageState  

MscAtmIfVptIispSigOperEntry  
SEQUENCE    
  Unsigned32 as mscAtmIfVptIispSigLastTxCauseCode  
  Hex as mscAtmIfVptIispSigLastTxDiagCode  
  Unsigned32 as mscAtmIfVptIispSigLastRxCauseCode  
  Hex as mscAtmIfVptIispSigLastRxDiagCode  

MscAtmIfVptIispSigStatsEntry  
SEQUENCE    
  Counter32 as mscAtmIfVptIispSigCurrentConnections  
  Gauge32 as mscAtmIfVptIispSigPeakConnections  
  Counter32 as mscAtmIfVptIispSigSuccessfulConnections  
  Counter32 as mscAtmIfVptIispSigFailedConnections  
  Counter32 as mscAtmIfVptIispSigTxPdus  
  Counter32 as mscAtmIfVptIispSigRxPdus  
  Gauge32 as mscAtmIfVptIispSigCurrentPmpConnections  
  Gauge32 as mscAtmIfVptIispSigPeakPmpConnections  
  Counter32 as mscAtmIfVptIispSigSuccessfulPmpConnections  
  Counter32 as mscAtmIfVptIispSigFailedPmpConnections  
  Gauge32 as mscAtmIfVptIispSigNewCurrentConnections  

MscAtmIfVptIispSigVcdRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfVptIispSigVcdRowStatus  
  DisplayString as mscAtmIfVptIispSigVcdComponentName  
  StorageType as mscAtmIfVptIispSigVcdStorageType  
  NonReplicated as mscAtmIfVptIispSigVcdIndex  

MscAtmIfVptIispSigVcdProvEntry  
SEQUENCE    
  INTEGER as mscAtmIfVptIispSigVcdTrafficDescType  
  INTEGER as mscAtmIfVptIispSigVcdAtmServiceCategory  
  Unsigned32 as mscAtmIfVptIispSigVcdWeight  
  INTEGER as mscAtmIfVptIispSigVcdQosClass  
  INTEGER as mscAtmIfVptIispSigVcdTrafficShaping  
  INTEGER as mscAtmIfVptIispSigVcdUnshapedTransmitQueueing  
  INTEGER as mscAtmIfVptIispSigVcdUsageParameterControl  

MscAtmIfVptIispSigVcdTdpEntry  
SEQUENCE    
  Integer32 as mscAtmIfVptIispSigVcdTdpIndex  
  Unsigned32 as mscAtmIfVptIispSigVcdTdpValue  

MscAtmIfVptIispAddrRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfVptIispAddrRowStatus  
  DisplayString as mscAtmIfVptIispAddrComponentName  
  StorageType as mscAtmIfVptIispAddrStorageType  
  AsciiStringIndex as mscAtmIfVptIispAddrAddressIndex  
  INTEGER as mscAtmIfVptIispAddrAddressTypeIndex  

MscAtmIfVptIispAddrOperEntry  
SEQUENCE    
  INTEGER as mscAtmIfVptIispAddrScope  
  INTEGER as mscAtmIfVptIispAddrReachability  

MscAtmIfVptIispAddrTermSPRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfVptIispAddrTermSPRowStatus  
  DisplayString as mscAtmIfVptIispAddrTermSPComponentName  
  StorageType as mscAtmIfVptIispAddrTermSPStorageType  
  NonReplicated as mscAtmIfVptIispAddrTermSPIndex  

MscAtmIfVptIispAddrPnniInfoRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfVptIispAddrPnniInfoRowStatus  
  DisplayString as mscAtmIfVptIispAddrPnniInfoComponentName  
  StorageType as mscAtmIfVptIispAddrPnniInfoStorageType  
  NonReplicated as mscAtmIfVptIispAddrPnniInfoIndex  

MscAtmIfVptIispAddrPnniInfoProvEntry  
SEQUENCE    
  INTEGER as mscAtmIfVptIispAddrPnniInfoScope  
  INTEGER as mscAtmIfVptIispAddrPnniInfoReachability  

MscAtmIfVptIispCallingAScrRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfVptIispCallingAScrRowStatus  
  DisplayString as mscAtmIfVptIispCallingAScrComponentName  
  StorageType as mscAtmIfVptIispCallingAScrStorageType  
  NonReplicated as mscAtmIfVptIispCallingAScrIndex  

MscAtmIfVptIispCallingAScrProvEntry  
SEQUENCE    
  INTEGER as mscAtmIfVptIispCallingAScrAdminStatus  
  HexString as mscAtmIfVptIispCallingAScrDefaultInsertionAddress  

MscAtmIfVptIispCallingAScrStatEntry  
SEQUENCE    
  Counter32 as mscAtmIfVptIispCallingAScrAcceptedCalls  
  Counter32 as mscAtmIfVptIispCallingAScrRejectedCalls  
  Counter32 as mscAtmIfVptIispCallingAScrUnmatchedCalls  

MscAtmIfVptIispCallingAScrAddrRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfVptIispCallingAScrAddrRowStatus  
  DisplayString as mscAtmIfVptIispCallingAScrAddrComponentName  
  StorageType as mscAtmIfVptIispCallingAScrAddrStorageType  
  AsciiStringIndex as mscAtmIfVptIispCallingAScrAddrAddressIndex  
  INTEGER as mscAtmIfVptIispCallingAScrAddrAddressActionIndex  

MscAtmIfVptIispCalledAScrRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfVptIispCalledAScrRowStatus  
  DisplayString as mscAtmIfVptIispCalledAScrComponentName  
  StorageType as mscAtmIfVptIispCalledAScrStorageType  
  NonReplicated as mscAtmIfVptIispCalledAScrIndex  

MscAtmIfVptIispCalledAScrProvEntry  
SEQUENCE    
  INTEGER as mscAtmIfVptIispCalledAScrAdminStatus  

MscAtmIfVptIispCalledAScrStatEntry  
SEQUENCE    
  Counter32 as mscAtmIfVptIispCalledAScrAcceptedCalls  
  Counter32 as mscAtmIfVptIispCalledAScrRejectedCalls  
  Counter32 as mscAtmIfVptIispCalledAScrUnmatchedCalls  

MscAtmIfVptIispCalledAScrAddrRowStatusEntry  
SEQUENCE    
  RowStatus as mscAtmIfVptIispCalledAScrAddrRowStatus  
  DisplayString as mscAtmIfVptIispCalledAScrAddrComponentName  
  StorageType as mscAtmIfVptIispCalledAScrAddrStorageType  
  AsciiStringIndex as mscAtmIfVptIispCalledAScrAddrAddressIndex  
  INTEGER as mscAtmIfVptIispCalledAScrAddrAddressActionIndex