Nortel-MsCarrier-MscPassport-FrameRelayUniMIB

File: Nortel-MsCarrier-MscPassport-FrameRelayUniMIB.mib (417571 bytes)

Imported modules

RFC-1212 Nortel-MsCarrier-MscPassport-UsefulDefinitionsMIB Nortel-MsCarrier-MscPassport-StandardTextualConventionsMIB
Nortel-MsCarrier-MscPassport-TextualConventionsMIB

Imported symbols

OBJECT-TYPE mscPassportMIBs mscComponents
Counter32 RowPointer DisplayString
StorageType RowStatus InterfaceIndex
Gauge32 Integer32 Unsigned32
AsciiString Hex NonReplicated
FixedPoint3 HexString EnterpriseDateAndTime
PassportCounter64 Link DigitString
Unsigned64

Defined Objects

mscFrUni 1.3.6.1.4.1.562.36.2.1.71
OBJECT IDENTIFIER    

mscFrUniRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.1
This entry controls the addition and deletion of mscFrUni components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniRowStatusEntry

mscFrUniRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.1.1
A single entry in the table represents a single mscFrUni component.
OBJECT-TYPE    
  MscFrUniRowStatusEntry  

mscFrUniRowStatus 1.3.6.1.4.1.562.36.2.1.71.1.1.1
This variable is used as the basis for SNMP naming of mscFrUni components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniComponentName 1.3.6.1.4.1.562.36.2.1.71.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniStorageType 1.3.6.1.4.1.562.36.2.1.71.1.1.4
This variable represents the storage type value for the mscFrUni tables.
OBJECT-TYPE    
  StorageType  

mscFrUniIndex 1.3.6.1.4.1.562.36.2.1.71.1.1.10
This variable represents the index for the mscFrUni tables.
OBJECT-TYPE    
  Integer32 1..65535  

mscFrUniDna 1.3.6.1.4.1.562.36.2.1.71.2
OBJECT IDENTIFIER    

mscFrUniDnaRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.2.1
This entry controls the addition and deletion of mscFrUniDna components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDnaRowStatusEntry

mscFrUniDnaRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.2.1.1
A single entry in the table represents a single mscFrUniDna component.
OBJECT-TYPE    
  MscFrUniDnaRowStatusEntry  

mscFrUniDnaRowStatus 1.3.6.1.4.1.562.36.2.1.71.2.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniDna components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniDnaComponentName 1.3.6.1.4.1.562.36.2.1.71.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniDnaStorageType 1.3.6.1.4.1.562.36.2.1.71.2.1.1.4
This variable represents the storage type value for the mscFrUniDna tables.
OBJECT-TYPE    
  StorageType  

mscFrUniDnaIndex 1.3.6.1.4.1.562.36.2.1.71.2.1.1.10
This variable represents the index for the mscFrUniDna tables.
OBJECT-TYPE    
  NonReplicated  

mscFrUniDnaCug 1.3.6.1.4.1.562.36.2.1.71.2.2
OBJECT IDENTIFIER    

mscFrUniDnaCugRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.2.2.1
This entry controls the addition and deletion of mscFrUniDnaCug components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDnaCugRowStatusEntry

mscFrUniDnaCugRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.2.2.1.1
A single entry in the table represents a single mscFrUniDnaCug component.
OBJECT-TYPE    
  MscFrUniDnaCugRowStatusEntry  

mscFrUniDnaCugRowStatus 1.3.6.1.4.1.562.36.2.1.71.2.2.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniDnaCug components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniDnaCugComponentName 1.3.6.1.4.1.562.36.2.1.71.2.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniDnaCugStorageType 1.3.6.1.4.1.562.36.2.1.71.2.2.1.1.4
This variable represents the storage type value for the mscFrUniDnaCug tables.
OBJECT-TYPE    
  StorageType  

mscFrUniDnaCugIndex 1.3.6.1.4.1.562.36.2.1.71.2.2.1.1.10
This variable represents the index for the mscFrUniDnaCug tables.
OBJECT-TYPE    
  Integer32 0..255  

mscFrUniDnaCugCugOptionsTable 1.3.6.1.4.1.562.36.2.1.71.2.2.10
Attributes in this group define ClosedUserGroup options associated with interlockCode. DNA's with the same CUG (interlockCode) can make calls within this group. Various combinations which permit or prevent calls in the same CUG group are defined here.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDnaCugCugOptionsEntry

mscFrUniDnaCugCugOptionsEntry 1.3.6.1.4.1.562.36.2.1.71.2.2.10.1
An entry in the mscFrUniDnaCugCugOptionsTable.
OBJECT-TYPE    
  MscFrUniDnaCugCugOptionsEntry  

mscFrUniDnaCugType 1.3.6.1.4.1.562.36.2.1.71.2.2.10.1.1
This attribute specifies the CUG type - the CUG is either a national CUG, or an international CUG. International closed user groups are usually established between DTEs for which there is an X.75 Gateway between; whereas national closed user groups are usually established between DTEs for which there is no X.75 Gateway between. (National CUGs cannot normally traverse an X.75 Gateway). If this attribute is set to national, then the CUG is a national CUG, in which case, the dnic should be left at its default value since it is not part of a national CUG. If this attribute is set to international, then the CUG is an international CUG, in which case, the dnic should be set appropriately as part of the CUG interlockCode.
OBJECT-TYPE    
  INTEGER national(0), international(1)  

mscFrUniDnaCugDnic 1.3.6.1.4.1.562.36.2.1.71.2.2.10.1.2
This attribute specifies the dnic (Data Network ID Code) of the CUG by which packet networks are identified. This attribute is not applicable if the CUG is a national CUG, as specified by the CUG type attribute. There are usually 1 or 2 dnics assigned per country, for public networks. The U.S. is an exception where each BOC has a dnic. Also, a group of private networks can have its own dnic. dnic value is not an arbitrary number. It is assigned by international agreement and controlled by CCITT.
OBJECT-TYPE    
  DigitString SIZE(4)  

mscFrUniDnaCugInterlockCode 1.3.6.1.4.1.562.36.2.1.71.2.2.10.1.3
This attribute specifies the CUG identifier of a national or international CUG call. It is an arbitrary number and it also can be called CUG in some descriptions. Interfaces (DNA's) defined with this number can make calls to DNA's with the same interlockCode.
OBJECT-TYPE    
  Unsigned32 0..65535  

mscFrUniDnaCugPreferential 1.3.6.1.4.1.562.36.2.1.71.2.2.10.1.4
The attribute 'preferential', if set to yes indicates that this CUG is the SIMPLE CUG (as defined in ITU X.36 [10/96]), in which case it will be used during the call establishment phase if the DTE has not explicitly specified a CUG index in the call request packet. If set to no, then this CUG is not the SIMPLE CUG, but an instance of the SELECTABLE CUG. The attribute 'preferential' is set to no by CAS when a CUG instance is created. If only one CUG instance exists under a DNA, and if this CUG's attributes 'incCalls' and 'outCall' are both set to allowed, then this CUG instance can be changed to a SIMPLE CUG by setting the attribute 'preferential' to yes. If more than one CUG instances exist under a DNA, none of the CUGs can be set by the user as 'preferential'. Essentially, the attribute 'preferential' distinguishes a SIMPLE CUG from a SELECTABLE CUG. In the case of a FRUNI DNA with a single CUG instance, the CUG can be a SIMPLE CUG (preferential = yes) or the only instance of a SELECTABLE CUG (preferential = no).
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mscFrUniDnaCugOutCalls 1.3.6.1.4.1.562.36.2.1.71.2.2.10.1.5
This attribute, if set to allowed indicates that outgoing calls (from the DTE into the network) can be made using this particular CUG. If set to a value of disallowed, then outgoing calls cannot be made using this CUG - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Outgoing Calls Barred' feature for CUGs in that outgoing calls are barred if this attribute is set to a value of disallowed.
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

mscFrUniDnaCugIncCalls 1.3.6.1.4.1.562.36.2.1.71.2.2.10.1.6
This attribute, if set to allowed indicates that incoming calls (from the network to the DTE) can be made using this particular CUG. If set to disallowed, then incoming calls cannot be made using this CUG - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Incoming Calls Barred' feature for CUGs in that incoming calls are barred if this attribute is set to a value of disallowed.
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

mscFrUniDnaHgM 1.3.6.1.4.1.562.36.2.1.71.2.3
OBJECT IDENTIFIER    

mscFrUniDnaHgMRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.2.3.1
This entry controls the addition and deletion of mscFrUniDnaHgM components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDnaHgMRowStatusEntry

mscFrUniDnaHgMRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.2.3.1.1
A single entry in the table represents a single mscFrUniDnaHgM component.
OBJECT-TYPE    
  MscFrUniDnaHgMRowStatusEntry  

mscFrUniDnaHgMRowStatus 1.3.6.1.4.1.562.36.2.1.71.2.3.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniDnaHgM components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniDnaHgMComponentName 1.3.6.1.4.1.562.36.2.1.71.2.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniDnaHgMStorageType 1.3.6.1.4.1.562.36.2.1.71.2.3.1.1.4
This variable represents the storage type value for the mscFrUniDnaHgM tables.
OBJECT-TYPE    
  StorageType  

mscFrUniDnaHgMIndex 1.3.6.1.4.1.562.36.2.1.71.2.3.1.1.10
This variable represents the index for the mscFrUniDnaHgM tables.
OBJECT-TYPE    
  NonReplicated  

mscFrUniDnaHgMHgAddr 1.3.6.1.4.1.562.36.2.1.71.2.3.2
OBJECT IDENTIFIER    

mscFrUniDnaHgMHgAddrRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.2.3.2.1
This entry controls the addition and deletion of mscFrUniDnaHgMHgAddr components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDnaHgMHgAddrRowStatusEntry

mscFrUniDnaHgMHgAddrRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.2.3.2.1.1
A single entry in the table represents a single mscFrUniDnaHgMHgAddr component.
OBJECT-TYPE    
  MscFrUniDnaHgMHgAddrRowStatusEntry  

mscFrUniDnaHgMHgAddrRowStatus 1.3.6.1.4.1.562.36.2.1.71.2.3.2.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniDnaHgMHgAddr components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniDnaHgMHgAddrComponentName 1.3.6.1.4.1.562.36.2.1.71.2.3.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniDnaHgMHgAddrStorageType 1.3.6.1.4.1.562.36.2.1.71.2.3.2.1.1.4
This variable represents the storage type value for the mscFrUniDnaHgMHgAddr tables.
OBJECT-TYPE    
  StorageType  

mscFrUniDnaHgMHgAddrIndex 1.3.6.1.4.1.562.36.2.1.71.2.3.2.1.1.10
This variable represents the index for the mscFrUniDnaHgMHgAddr tables.
OBJECT-TYPE    
  Integer32 0..1  

mscFrUniDnaHgMHgAddrAddrTable 1.3.6.1.4.1.562.36.2.1.71.2.3.2.10
This group contains attributes common to all DNAs. Every DNA used in the network is defined with this group of 2 attributes.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDnaHgMHgAddrAddrEntry

mscFrUniDnaHgMHgAddrAddrEntry 1.3.6.1.4.1.562.36.2.1.71.2.3.2.10.1
An entry in the mscFrUniDnaHgMHgAddrAddrTable.
OBJECT-TYPE    
  MscFrUniDnaHgMHgAddrAddrEntry  

mscFrUniDnaHgMHgAddrNumberingPlanIndicator 1.3.6.1.4.1.562.36.2.1.71.2.3.2.10.1.1
This attribute indicates the Numbering Plan Indicator (NPI) of the DNA. The address may belong to X.121 or E.164 plans.
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

mscFrUniDnaHgMHgAddrDataNetworkAddress 1.3.6.1.4.1.562.36.2.1.71.2.3.2.10.1.2
This attribute contains digits which form the unique identifier of the customer interface. It can be compared (approximation only) to a telephone number where the phone number identifies a unique telephone set. DNA digits are selected and assigned by network operators.
OBJECT-TYPE    
  DigitString SIZE(1..15)  

mscFrUniDnaHgMIfTable 1.3.6.1.4.1.562.36.2.1.71.2.3.10
This group contains the interface parameters between the HuntGroupMember and the hunt group server.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDnaHgMIfEntry

mscFrUniDnaHgMIfEntry 1.3.6.1.4.1.562.36.2.1.71.2.3.10.1
An entry in the mscFrUniDnaHgMIfTable.
OBJECT-TYPE    
  MscFrUniDnaHgMIfEntry  

mscFrUniDnaHgMAvailabilityUpdateThreshold 1.3.6.1.4.1.562.36.2.1.71.2.3.10.1.1
This attribute specifies how much availableAggregateCIR can change before an Availability Message Packet (AMP) is sent to the hunt group server informing it of the change. If the value specified is not a multiple of 2048, the value actually used as the threshold will be the next higher multiple of 2048.
OBJECT-TYPE    
  Unsigned32 2048..16777216  

mscFrUniDnaHgMOpTable 1.3.6.1.4.1.562.36.2.1.71.2.3.11
This group contains the operational attributes of the HuntGroupMember component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDnaHgMOpEntry

mscFrUniDnaHgMOpEntry 1.3.6.1.4.1.562.36.2.1.71.2.3.11.1
An entry in the mscFrUniDnaHgMOpTable.
OBJECT-TYPE    
  MscFrUniDnaHgMOpEntry  

mscFrUniDnaHgMMaximumAvailableAggregateCir 1.3.6.1.4.1.562.36.2.1.71.2.3.11.1.1
This attribute indicates the maximum available bandwidth for this hunt group member. This value represents the total sum of the sixteen egress bandwidth pools. It is the sum of the sixteen indices of the FrUni Ca egressBandwidthPool attribute multiplied by the link speed.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDnaHgMAvailableAggregateCir 1.3.6.1.4.1.562.36.2.1.71.2.3.11.1.2
This attribute indicates the current total available bandwidth reported to the hunt group server in the Availability Message Packet (AMP). This value represents the sum of the sixteen currently available egress bandwidth pools. It is the sum of the sixteen indices of the FrUni Ca egressPoolAvailableBandwidth attribute. It increments when a connection is released. It decrements when a connection is accepted. Both this attribute and the availableDlcis attribute must be non zero for this interface to receive calls on a hunt group.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDnaHgMAvailabilityDelta 1.3.6.1.4.1.562.36.2.1.71.2.3.11.1.3
This attribute indicates the net change in the available aggregate CIR since the last Availability Message Packet (AMP) was sent to the Hunt Group. Once the absolute value of this attribute reaches the availabilityUpdateThreshold an AMP is sent to the hunt group server(s) and the availabilityDelta is re-computed.
OBJECT-TYPE    
  INTEGER -16777216..16777215  

mscFrUniDnaHgMAvailableDlcis 1.3.6.1.4.1.562.36.2.1.71.2.3.11.1.5
This attribute indicates the number of DLCIs available for SVCs on the interface associated with this DNA. If this value reaches 0, an AMP with zero availability is sent to the hunt group server(s). Both this attribute and the availableAggregateCir attribute must be non zero for this DNA to receive calls on the hunt group.
OBJECT-TYPE    
  Unsigned32 0..4096  

mscFrUniDnaAddressTable 1.3.6.1.4.1.562.36.2.1.71.2.10
This group contains attributes common to all DNAs. Every DNA used in the network is defined with this group of 2 attributes.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDnaAddressEntry

mscFrUniDnaAddressEntry 1.3.6.1.4.1.562.36.2.1.71.2.10.1
An entry in the mscFrUniDnaAddressTable.
OBJECT-TYPE    
  MscFrUniDnaAddressEntry  

mscFrUniDnaNumberingPlanIndicator 1.3.6.1.4.1.562.36.2.1.71.2.10.1.1
This attribute indicates the Numbering Plan Indicator (NPI) of the DNA that is entered. Address may belong to X.121 or E.164 plans. X.121 is used in packet switched data networks.
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

mscFrUniDnaDataNetworkAddress 1.3.6.1.4.1.562.36.2.1.71.2.10.1.2
This attribute indicates the customer's unique identifier. It is the equivalent of the telephone number in the telephone network.
OBJECT-TYPE    
  DigitString SIZE(1..15)  

mscFrUniDnaOutgoingOptionsTable 1.3.6.1.4.1.562.36.2.1.71.2.11
This group defines DNA call options for calls made from the interface. These options are not used for calls arriving to the interface represented by this DNA.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDnaOutgoingOptionsEntry

mscFrUniDnaOutgoingOptionsEntry 1.3.6.1.4.1.562.36.2.1.71.2.11.1
An entry in the mscFrUniDnaOutgoingOptionsTable.
OBJECT-TYPE    
  MscFrUniDnaOutgoingOptionsEntry  

mscFrUniDnaOutDefaultPriority 1.3.6.1.4.1.562.36.2.1.71.2.11.1.7
This attribute indicates the default priority of outgoing calls from the DTE to the network. It can be overridden by the discardPriority under DLCI Direct Call subcomponent. This option can be also included in X.25 signalling, in such case it will be overruled.
OBJECT-TYPE    
  INTEGER normal(0), high(1)  

mscFrUniDnaOutDefaultPathSensitivity 1.3.6.1.4.1.562.36.2.1.71.2.11.1.11
This attribute specifies the default class of path sensitivity to network for all outgoing calls that use this DNA. The chosen default class of path sensitivity applies to all outgoing calls established using this DNA. This attribute, if set to throughput, indicates that the default class is throughput sensitive. If set to delay, then the default class is delay sensitive. The default of outDefaultPathSensitivity is throughput.
OBJECT-TYPE    
  INTEGER throughput(0), delay(1)  

mscFrUniDnaOutPathSensitivityOverRide 1.3.6.1.4.1.562.36.2.1.71.2.11.1.12
If this attribute is set to yes in the call request, the called end will use the calling end provisioning data on path sensitivity to override its own provisioning data. The default of outPathSensitivityOverRide is yes.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mscFrUniDnaOutDefaultPathReliability 1.3.6.1.4.1.562.36.2.1.71.2.11.1.14
This attribute specifies the default class of routing for reliability routing for all outgoing calls (from the DTE to the network) using this particular DNA. The chosen default class of routing applies to all outgoing calls established using this DNA, and applies to the packets travelling in both directions on all outgoing calls (local to remote, and remote to local). For incoming calls, the default class of routing is chosen by the calling party (as opposed to DPN, where either end of the call can choose the default routing class). This attribute, if set to a value of normal, indicates that the default class of routing is normal reliability routing. If set to a value of high, then the default class of routing is high reliability routing. High reliability is the standard choice for most DPN and Passport services. It usually indicates that packets are overflowed or retransmitted at various routing levels. Typically high reliability results in duplication and disordering of packets in the network when errors are detected or during link congestion. However, the VC handles the duplication and disordering to ensure that packets are delivered to the DTE properly. For the Frame Relay service, duplication of packets is not desired, in which case, normal reliability may be chosen as the preferred class of routing.
OBJECT-TYPE    
  INTEGER high(0), normal(1)  

mscFrUniDnaOutAccess 1.3.6.1.4.1.562.36.2.1.71.2.11.1.17
This attribute is an extension of the Closed User Group (CUG) facility, as follows: This attribute, if set to a value of allowed indicates that outgoing calls (from the DTE to the network) to the open (non-CUG) part of the network are permitted. It also permits outgoing calls to DTEs that have Incoming Access capabilities. If set to a value of disallowed, then such calls cannot be made using this DNA. Such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Closed User Group with Outgoing Access' feature for DNAs in that outgoing access is granted if this attribute is set to a value of allowed.
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

mscFrUniDnaDefaultTransferPriority 1.3.6.1.4.1.562.36.2.1.71.2.11.1.18
This attribute specifies the default transfer priority for all outgoing calls using this particular DNA. It can be overridden by the transferPriority provisioned in the Dlci DirectCall sub-component. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 levels from 0 to 15. Each transfer priority n, where n indicates the transfer priority index, contains a default setting for routing class of service (multimedia, delay or throughput) and frame relay egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned in the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required. The default defaultTransferPriority is 0.
OBJECT-TYPE    
  INTEGER n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15)  

mscFrUniDnaTransferPriorityOverRide 1.3.6.1.4.1.562.36.2.1.71.2.11.1.19
When this attribute is set to yes in the call request, the called end will use the calling end provisioning data on transfer priority to override its own provisioning data. If it is set no, the called end will use its own provisioning data on transfer priority. This attribute is not applicable for Frame Relay SVCs. For more information about transfer priority, please refer to the previous attribute defaultTransferPriority. The default of transferPriorityOverRide is yes.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mscFrUniDnaIncomingOptionsTable 1.3.6.1.4.1.562.36.2.1.71.2.12
This group defines options for incoming calls. These options are used for calls arriving to the interface represented by this DNA. For calls originated from the interface, IncomingOptions attributes are not used.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDnaIncomingOptionsEntry

mscFrUniDnaIncomingOptionsEntry 1.3.6.1.4.1.562.36.2.1.71.2.12.1
An entry in the mscFrUniDnaIncomingOptionsTable.
OBJECT-TYPE    
  MscFrUniDnaIncomingOptionsEntry  

mscFrUniDnaIncAccess 1.3.6.1.4.1.562.36.2.1.71.2.12.1.9
This attribute, if set to a value of allowed specifies that incoming calls (from the network to the DTE) from the open (non-CUG) part of the network are permitted. It also permits incoming calls from DTEs that have outgoing access capabilities. If set to a value of disallowed, such calls cannot be made to this DNA. They will be cleared by the local DCE. This attribute corresponds to the CCITT 'Closed User Group with Incoming Access' feature for DNAs in that incoming access is granted if this attribute is set to a value of allowed.
OBJECT-TYPE    
  INTEGER disallowed(0), allowed(1)  

mscFrUniDnaCallOptionsTable 1.3.6.1.4.1.562.36.2.1.71.2.13
This group defines additional all options for not related to direction of the call.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDnaCallOptionsEntry

mscFrUniDnaCallOptionsEntry 1.3.6.1.4.1.562.36.2.1.71.2.13.1
An entry in the mscFrUniDnaCallOptionsTable.
OBJECT-TYPE    
  MscFrUniDnaCallOptionsEntry  

mscFrUniDnaAccountClass 1.3.6.1.4.1.562.36.2.1.71.2.13.1.10
This attribute specifies the accounting class which is reserved for network operations usage. Its value is returned in the accounting record in the local and remote service type attributes. Use of this attribute is decided by network operator. This attribute is returned by the local VC in the accounting record for all calls that are set up using this particular DNA.
OBJECT-TYPE    
  Unsigned32 0..255  

mscFrUniDnaAccountCollection 1.3.6.1.4.1.562.36.2.1.71.2.13.1.11
This attribute indicates that accounting records are to be collected by the network for the various reasons: billing, test, study, auditing. The last of the parameters, force, indicates that accounting records are to be collected irrespective of other collection reasons. The force option is available for X.75 Gateways only. If none of these reasons are set, then accounting will be suppressed. To set a specific accounting collection reason, the reason is entered and the corresponding bit in the structure is set to a value of 1. To turn off a specific accounting collection reason, the reason is entered preceded with the '~' character, and the corresponding bit in the structure is set to a value of 0. The bit placement for the accounting collection reasons is as follows: Bit 0 - Bill Bit 1 - Test Bit 2 - Study Bit 3 - Audit Bit 4 - Force Description of bits: bill(0) test(1) study(2) audit(3) force(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscFrUniDnaServiceExchange 1.3.6.1.4.1.562.36.2.1.71.2.13.1.12
This attribute is an arbitrary number, Data Service Exchange, as entered by the network operator and reported in accounting record. It is converted into an internal 8-bit integer value for use in the accounting record as well as in various X.25 and X.75 Tariff utilities.
OBJECT-TYPE    
  Unsigned32 0..255  

mscFrUniDnaEgressAccounting 1.3.6.1.4.1.562.36.2.1.71.2.13.1.13
This attribute specifies if egress accounting is enabled by the frame relay service. If egress accounting is disabled, only segment counts are collected by the VC. No frame relay counts appear in the accounting records for the frame relay service. If egress accounting is enabled, the accounting records for the frame relay service will contain frame relay specific counts.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mscFrUniDnaDataPath 1.3.6.1.4.1.562.36.2.1.71.2.13.1.21
This attribute specifies the data path to be used by Virtual Circuits on this interface. If the connection has a DirectCall component then the value can be overridden by the dataPath attribute of the DirectCall component. This value applies to the connection after data transfer state is reached. All the data and control trafic will be sent using this data path. If the provisioned dataPath is not available the connection is not established. The value of the dataPath is signalled by both ends of the connection. If this value is not the same at both ends dprsOnly is used for the duration of the connection. A virtual circuit connection is always established using dprsOnly even if this attribute is provisioned as some other value. dprsOnly - dynamic packet routing system is used dprsMcsOnly - dprs Multi-Service Cut-Through Switching path is used. dprsMcsFirst - dprs Multi-Service Cut-Through Switching path is used if it is available. If it is not avaliable dprsOnly is used.
OBJECT-TYPE    
  INTEGER dprsOnly(0), dprsMcsOnly(1), dprsMcsFirst(2)  

mscFrUniFramer 1.3.6.1.4.1.562.36.2.1.71.3
OBJECT IDENTIFIER    

mscFrUniFramerRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.3.1
This entry controls the addition and deletion of mscFrUniFramer components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniFramerRowStatusEntry

mscFrUniFramerRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.3.1.1
A single entry in the table represents a single mscFrUniFramer component.
OBJECT-TYPE    
  MscFrUniFramerRowStatusEntry  

mscFrUniFramerRowStatus 1.3.6.1.4.1.562.36.2.1.71.3.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniFramer components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniFramerComponentName 1.3.6.1.4.1.562.36.2.1.71.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniFramerStorageType 1.3.6.1.4.1.562.36.2.1.71.3.1.1.4
This variable represents the storage type value for the mscFrUniFramer tables.
OBJECT-TYPE    
  StorageType  

mscFrUniFramerIndex 1.3.6.1.4.1.562.36.2.1.71.3.1.1.10
This variable represents the index for the mscFrUniFramer tables.
OBJECT-TYPE    
  NonReplicated  

mscFrUniFramerProvTable 1.3.6.1.4.1.562.36.2.1.71.3.10
This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisionable Framer groups.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniFramerProvEntry

mscFrUniFramerProvEntry 1.3.6.1.4.1.562.36.2.1.71.3.10.1
An entry in the mscFrUniFramerProvTable.
OBJECT-TYPE    
  MscFrUniFramerProvEntry  

mscFrUniFramerInterfaceName 1.3.6.1.4.1.562.36.2.1.71.3.10.1.1
This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.
OBJECT-TYPE    
  Link  

mscFrUniFramerLinkTable 1.3.6.1.4.1.562.36.2.1.71.3.11
This group contains attributes defining the framing of data on the link interface.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniFramerLinkEntry

mscFrUniFramerLinkEntry 1.3.6.1.4.1.562.36.2.1.71.3.11.1
An entry in the mscFrUniFramerLinkTable.
OBJECT-TYPE    
  MscFrUniFramerLinkEntry  

mscFrUniFramerDataInversion 1.3.6.1.4.1.562.36.2.1.71.3.11.1.2
This attribute determines whether data bits are to be inverted (1 to 0 and 0 to 1) before transmission of frames to the interface. If the value of this attribute is On, the incoming data bits will also be inverted when frames are received from the link before being processed. This option is typically used in hdlc framing mode when inversion is used to guarantee 1's density. Note that aborts (in hdlc and interrupting modes) are corrupted when data is inverted. This attribute may only take its default value for non-MSA cards.
OBJECT-TYPE    
  INTEGER off(0), on(16)  

mscFrUniFramerFrameCrcType 1.3.6.1.4.1.562.36.2.1.71.3.11.1.3
This attribute defines the type of CRC used. The CRC value calculated is appended to the end of the frames transmitted to the link. The CRC value is removed from the end of frames received from the link and checked for correctness. NoCrc means that CRC is not used. This attribute may take only its default value for non-MSA cards.
OBJECT-TYPE    
  INTEGER crc16(0), crc32(1), noCrc(2)  

mscFrUniFramerFlagsBetweenFrames 1.3.6.1.4.1.562.36.2.1.71.3.11.1.4
This attribute defines the number of flags that are inserted between frames sent to the link interface.
OBJECT-TYPE    
  Unsigned32 1..16  

mscFrUniFramerStateTable 1.3.6.1.4.1.562.36.2.1.71.3.12
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniFramerStateEntry

mscFrUniFramerStateEntry 1.3.6.1.4.1.562.36.2.1.71.3.12.1
An entry in the mscFrUniFramerStateTable.
OBJECT-TYPE    
  MscFrUniFramerStateEntry  

mscFrUniFramerAdminState 1.3.6.1.4.1.562.36.2.1.71.3.12.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscFrUniFramerOperationalState 1.3.6.1.4.1.562.36.2.1.71.3.12.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscFrUniFramerUsageState 1.3.6.1.4.1.562.36.2.1.71.3.12.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscFrUniFramerStatsTable 1.3.6.1.4.1.562.36.2.1.71.3.13
This group contains the operational statistics data for a Framer component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniFramerStatsEntry

mscFrUniFramerStatsEntry 1.3.6.1.4.1.562.36.2.1.71.3.13.1
An entry in the mscFrUniFramerStatsTable.
OBJECT-TYPE    
  MscFrUniFramerStatsEntry  

mscFrUniFramerFrmToIf 1.3.6.1.4.1.562.36.2.1.71.3.13.1.1
The number of frames transmitted to the link interface by Framer. Note: This does not include the number of frames transmitted directly to the hardware queue, thus bypassing the Framer component.
OBJECT-TYPE    
  Counter32  

mscFrUniFramerFrmFromIf 1.3.6.1.4.1.562.36.2.1.71.3.13.1.2
The number of frames received from the link interface by Framer.
OBJECT-TYPE    
  Counter32  

mscFrUniFramerOctetFromIf 1.3.6.1.4.1.562.36.2.1.71.3.13.1.3
The number of bytes received from the link interface by Framer.
OBJECT-TYPE    
  Counter32  

mscFrUniFramerAborts 1.3.6.1.4.1.562.36.2.1.71.3.13.1.4
This attribute is the total number of aborts received.
OBJECT-TYPE    
  Counter32  

mscFrUniFramerCrcErrors 1.3.6.1.4.1.562.36.2.1.71.3.13.1.5
This attribute is the total number of frames with CRC errors, occurring in the receive direction from the link.
OBJECT-TYPE    
  Counter32  

mscFrUniFramerLrcErrors 1.3.6.1.4.1.562.36.2.1.71.3.13.1.6
This attribute is the total number of frames with LRC errors, occurring in the Tx link prior to transmission onto the link.
OBJECT-TYPE    
  Counter32  

mscFrUniFramerNonOctetErrors 1.3.6.1.4.1.562.36.2.1.71.3.13.1.7
This attribute is the total number of frames that were non octet aligned.
OBJECT-TYPE    
  Counter32  

mscFrUniFramerOverruns 1.3.6.1.4.1.562.36.2.1.71.3.13.1.8
This attribute is the total number of frames received from the link for which overruns occurred.
OBJECT-TYPE    
  Counter32  

mscFrUniFramerUnderruns 1.3.6.1.4.1.562.36.2.1.71.3.13.1.9
This attribute is the total number of frames transmitted to the link for which underruns occurred.
OBJECT-TYPE    
  Counter32  

mscFrUniFramerLargeFrmErrors 1.3.6.1.4.1.562.36.2.1.71.3.13.1.10
This attribute is the total number of frames received which were too large. The frame execeeded the maximumFrameLengthLimit provisioned attribute or it contained more than the 255 block hardware limit.
OBJECT-TYPE    
  Counter32  

mscFrUniFramerFrmModeErrors 1.3.6.1.4.1.562.36.2.1.71.3.13.1.11
This attribute is the total number of frames detected with framing mode errors. A framingModeError is flagged when frames are inconsistent with the specified framingType, that is when interrupting frames are used while running in hdlc mode.
OBJECT-TYPE    
  Counter32  

mscFrUniFramerFrmToIf64 1.3.6.1.4.1.562.36.2.1.71.3.13.1.14
The number of frames transmitted to the link interface by Framer. Note: This does not include the number of frames transmitted directly to the hardware queue, thus bypassing the Framer component.
OBJECT-TYPE    
  PassportCounter64  

mscFrUniFramerFrmFromIf64 1.3.6.1.4.1.562.36.2.1.71.3.13.1.15
The number of frames received from the link interface by Framer.
OBJECT-TYPE    
  PassportCounter64  

mscFrUniFramerOctetFromIf64 1.3.6.1.4.1.562.36.2.1.71.3.13.1.16
The number of bytes received from the link interface by Framer.
OBJECT-TYPE    
  PassportCounter64  

mscFrUniFramerUtilTable 1.3.6.1.4.1.562.36.2.1.71.3.14
This group contains the link utilizaiton operational data for a Framer component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniFramerUtilEntry

mscFrUniFramerUtilEntry 1.3.6.1.4.1.562.36.2.1.71.3.14.1
An entry in the mscFrUniFramerUtilTable.
OBJECT-TYPE    
  MscFrUniFramerUtilEntry  

mscFrUniFramerNormPrioLinkUtilToIf 1.3.6.1.4.1.562.36.2.1.71.3.14.1.1
This attribute is the utilization of the normal and high priority data traffic (interruptable traffic) sent to the link as a percentage of the available bandwidth on the link. Note that this indluces traffic with Transfer Priorities (TP) of 0, 6 and 9 and/or Emission Priority of 2 and 3. The utilization is the average for the last minute.
OBJECT-TYPE    
  Gauge32 0..100  

mscFrUniFramerNormPrioLinkUtilFromIf 1.3.6.1.4.1.562.36.2.1.71.3.14.1.3
This attribute is the utilization of the normal and high priority data traffic (interruptable traffic) received from the link as a percentage of the available bandwidth on the link. Note that this includes traffic with Transfer Priorities (TP) of 0, 6 and 9 and/or Emission Priority of 2 and 3. The utilization is the average for the last minute.
OBJECT-TYPE    
  Gauge32 0..100  

mscFrUniLmi 1.3.6.1.4.1.562.36.2.1.71.4
OBJECT IDENTIFIER    

mscFrUniLmiRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.4.1
This entry controls the addition and deletion of mscFrUniLmi components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniLmiRowStatusEntry

mscFrUniLmiRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.4.1.1
A single entry in the table represents a single mscFrUniLmi component.
OBJECT-TYPE    
  MscFrUniLmiRowStatusEntry  

mscFrUniLmiRowStatus 1.3.6.1.4.1.562.36.2.1.71.4.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniLmi components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniLmiComponentName 1.3.6.1.4.1.562.36.2.1.71.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniLmiStorageType 1.3.6.1.4.1.562.36.2.1.71.4.1.1.4
This variable represents the storage type value for the mscFrUniLmi tables.
OBJECT-TYPE    
  StorageType  

mscFrUniLmiIndex 1.3.6.1.4.1.562.36.2.1.71.4.1.1.10
This variable represents the index for the mscFrUniLmi tables.
OBJECT-TYPE    
  NonReplicated  

mscFrUniLmiParmsTable 1.3.6.1.4.1.562.36.2.1.71.4.10
This group contains the provisionable attributes of the LMI component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniLmiParmsEntry

mscFrUniLmiParmsEntry 1.3.6.1.4.1.562.36.2.1.71.4.10.1
An entry in the mscFrUniLmiParmsTable.
OBJECT-TYPE    
  MscFrUniLmiParmsEntry  

mscFrUniLmiProcedures 1.3.6.1.4.1.562.36.2.1.71.4.10.1.1
This attribute selects the procedures to be used for the Local Management Interface. The following procedures are supported: none: no Local Management Interface procedures are running on this interface. This accommodates Frame Relay user equipment that has not implemented any LMI procedures. The remaining attributes of this group are ignored. vendorForum: Local Management Interface procedures from the Vendor Forum specification are supported on this interface. DLCI 1023 is used for the LMI protocol. This value cannot be used if the side attribute is both. ansi: Local Management Interface procedures from the ANSI specification are supported. DLCI 0 is used for the LMI protocol. itu: Local Management Interface procedures from the ITU-T specification are supported. DLCI 0 is used for the LMI protocol. Was previously ccitt. autoConfigure: The interface determines automatically which Local Management Interface procedures to use. This value cannot be used if the side attribute is user. The procedures currently in use can be seen in the operational attribute opProcedures.
OBJECT-TYPE    
  INTEGER none(0), vendorForum(1), ansi(2), itu(3), autoConfigure(4)  

mscFrUniLmiAsyncStatusReport 1.3.6.1.4.1.562.36.2.1.71.4.10.1.2
This attribute selects the use of asynchronous PVC status report procedures as specified in ANSI, CCITT, and Vendor Forum. This attribute can be set to on or off. If procedures is set to none, this attribute is ignored.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscFrUniLmiErrorEventThreshold 1.3.6.1.4.1.562.36.2.1.71.4.10.1.3
An event is defined as follows: (1) receipt of a STATUS ENQUIRY message; or (2) expiration of timer T392. An error event is (1) nonreceipt of STATUS ENQUIRY in T392 seconds; (2) invalid contents of a LMI message; (3) invalid receive sequence number. This attribute specifies the number of error events which, if they occur within eventCount events, cause a protocol error condition. The condition is cleared after eventCount sequential correct events occur. This attribute corresponds to the nN2 parameter described in the Vendor Forum Specification. It must be less than or equal to eventCount.
OBJECT-TYPE    
  Unsigned32 1..10  

mscFrUniLmiEventCount 1.3.6.1.4.1.562.36.2.1.71.4.10.1.4
This attribute specifies the number of contiguous events within which no more than eventErrorThreshold error events are allowed. This attribute corresponds to the nN3 parameter described in the Vendor Forum Specification. It must be greater than or equal to errorEventThreshold.
OBJECT-TYPE    
  Unsigned32 1..10  

mscFrUniLmiCheckPointTimer 1.3.6.1.4.1.562.36.2.1.71.4.10.1.5
This attribute selects the time (in seconds) within which a STATUS ENQUIRY message is expected. This attribute corresponds to the nT2 parameter described in the Vendor Forum Specification. It must be less than messageCountTimer.
OBJECT-TYPE    
  Unsigned32 5 | 10 | 15 | 20 | 25 | 30  

mscFrUniLmiMessageCountTimer 1.3.6.1.4.1.562.36.2.1.71.4.10.1.6
This attribute selects the time (in seconds) within which at most five (this is a fixed value and corresponds to maximum message count in VendorForum) STATUS ENQUIRY messages are expected. This attribute applies only when the lmiProcedures is set to vendorForum. messageCountTimer must always be greater than checkPointTimer.
OBJECT-TYPE    
  Unsigned32 5 | 10 | 15 | 20 | 25 | 30  

mscFrUniLmiIgnoreActiveBit 1.3.6.1.4.1.562.36.2.1.71.4.10.1.7
This attribute specifies whether the Frame Relay LMI Active Bit (A-bit) has a bearing on the transfer of user data across this Frame Relay interface for both directions of traffic flow. When this attribute is set to yes, the A-bit status of a user DLCI connection does not affect data transfer. When this attribute is set to no, data received from the local interface will be discarded if an A-bit =0 condition exists towards the local user. Data being sent to the local interface is discarded if an A-bit = 0 condition exists towards the subnet.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mscFrUniLmiSide 1.3.6.1.4.1.562.36.2.1.71.4.10.1.8
This attribute can be set to user, network, or both. When this attribute is set to user, USP LMI procedures are running. When this attribute is set to network, NSP LMI procedures are running. When this attribute is set to both, USPNSP LMI procedures are running. When the value is both, the procedures attribute must not be set to vendorForum. Setting the value to user when the procedures attribute is set to autoConfigure is disallowed semantically.
OBJECT-TYPE    
  INTEGER network(0), user(1), both(2)  

mscFrUniLmiPvcConfigParmsInFsr 1.3.6.1.4.1.562.36.2.1.71.4.10.1.9
When this attribute is set to yes, additional Q.933 information elements are included in the LMI Full Status message to facilitate CPE PVC parameter configuring. When set to yes, the Check Prov command fails if the Lmi side is not set to network. When set to yes, Check Prov fails if the number of DLCIs on the FrUni is greater than 300. If the service is not a FrUni this attribute is ignored.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mscFrUniLmiStateTable 1.3.6.1.4.1.562.36.2.1.71.4.11
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniLmiStateEntry

mscFrUniLmiStateEntry 1.3.6.1.4.1.562.36.2.1.71.4.11.1
An entry in the mscFrUniLmiStateTable.
OBJECT-TYPE    
  MscFrUniLmiStateEntry  

mscFrUniLmiAdminState 1.3.6.1.4.1.562.36.2.1.71.4.11.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscFrUniLmiOperationalState 1.3.6.1.4.1.562.36.2.1.71.4.11.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscFrUniLmiUsageState 1.3.6.1.4.1.562.36.2.1.71.4.11.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscFrUniLmiPsiTable 1.3.6.1.4.1.562.36.2.1.71.4.12
This group provides the protocol status of the Local Management Interface.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniLmiPsiEntry

mscFrUniLmiPsiEntry 1.3.6.1.4.1.562.36.2.1.71.4.12.1
An entry in the mscFrUniLmiPsiTable.
OBJECT-TYPE    
  MscFrUniLmiPsiEntry  

mscFrUniLmiProtocolStatus 1.3.6.1.4.1.562.36.2.1.71.4.12.1.1
This attribute indicates whether the LMI is in an error condition or whether the LMI procedures are behaving normally. When operating with no LMI protocol, this attribute is always set to normalCondition. When operating with LMI procedures, this attribute is set to errorCondition after n392 of the last n393 events are in error. The consequence of an errorCondition is that all DLCIs on this interface will become inactive in both directions. The errorCondition is cleared and a normalCondition is indicated when a sufficient number of events have occurred without error. In ANSI, this occurs when n393 consecutive good events take place. If the procedures attribute is set to autoConfigure, this attribute is set to configuring while adaptive LMI determines which LMI procedures are running on the link. A single LMI error event during auto configuration causes the attribute value to change to errorCondition. If during configuring no LMI message is received, an LMI errorCondition is raised after n392 x t392 seconds.
OBJECT-TYPE    
  INTEGER errorCondition(0), normalCondition(1), configuring(2)  

mscFrUniLmiOpProcedures 1.3.6.1.4.1.562.36.2.1.71.4.12.1.2
The opProcedures attribute indicates the procedures being used for the Local Management Interface. This attribute should be ignored if protocolStatus is not normalCondition. The following procedures are supported: none: Local Management Interface procedures are not running on this interface. This accommodates Frame Relay user equipment that has not implemented any LMI procedures. vendorForum: Local Management Interface procedures from the Vendor Forum specification are running on this interface. DLCI 1023 is used for the LMI protocol. ansi: Local Management Interface procedures from the ANSI specification are running. DLCI 0 is used for the LMI protocol. itu: Local Management Interface procedures from the ITU-T specification are running. DLCI 0 is used for the LMI protocol. Was previously ccitt. unknown: Local Management Interface procedures have yet to be determined by Adaptive LMI.
OBJECT-TYPE    
  INTEGER none(0), vendorForum(1), ansi(2), itu(3), unknown(4)  

mscFrUniLmiStatsTable 1.3.6.1.4.1.562.36.2.1.71.4.13
This group contains the operational statistics for the Frame Relay Local Management Interface.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniLmiStatsEntry

mscFrUniLmiStatsEntry 1.3.6.1.4.1.562.36.2.1.71.4.13.1
An entry in the mscFrUniLmiStatsTable.
OBJECT-TYPE    
  MscFrUniLmiStatsEntry  

mscFrUniLmiKeepAliveStatusToIf 1.3.6.1.4.1.562.36.2.1.71.4.13.1.1
This attribute counts the number of Local Management Interface keep alive status messages sent to the external user device in response to a status enquiry for keep alive status. When the maximum count is exceeded it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniLmiFullStatusToIf 1.3.6.1.4.1.562.36.2.1.71.4.13.1.2
This attribute counts the number of Local Management Interface full status messages sent to the external user device in response to a status enquiry for keep alive or full status. When the maximum count is reached it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniLmiKeepAliveStatusEnqFromIf 1.3.6.1.4.1.562.36.2.1.71.4.13.1.3
This attribute counts the number of Local Management Interface valid keep alive status enquiry messages received from the external user device. When the maximum count is reached it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniLmiFullStatusEnqFromIf 1.3.6.1.4.1.562.36.2.1.71.4.13.1.4
This attribute counts the number of Local Management Interface valid full status enquiry messages received from the external user device. When the maximum count is reached it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniLmiNetworkSideEventHistory 1.3.6.1.4.1.562.36.2.1.71.4.13.1.5
This attribute displays the Local Management Interface network side procedure event history in order of occurrence. An event is represented by a single symbol. A '+' symbol indicates a good event. An 'X' symbol indicates a protocol error event. The leftmost event is the most recent to occur. The provisioned eventCount (nN3/ N393) dictates the maximum number of events displayed. A good event is triggered by receipt of a valid status enquiry message. An error event is one of three possibilities, either a nT2/T392 timer expiry, receipt of a status enquiry message with bad sequence numbers, or when lmiProcedures is provisioned to vendorForum and we receive more than nN4 status enquiry messages within the provisioned messageCountTimer (nT3).
OBJECT-TYPE    
  AsciiString SIZE(1..10)  

mscFrUniLmiProtocolErrors 1.3.6.1.4.1.562.36.2.1.71.4.13.1.6
This attribute counts the number of Local Management Interface protocol errors. It is the sum of the sequence (sequenceErrors), timeout (pollingVerifTimeouts) and too many status enquiry messages received within the messageCountTimer (nT3) errors. The too many status enquiries error only applies when lmiProcedures is set to vendorForum. When the maximum count is exceeded it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniLmiUnexpectedIes 1.3.6.1.4.1.562.36.2.1.71.4.13.1.7
This attribute counts the number of Local Management Interface frames received with an Information Element identifier that is unknown or unexpected. An unexpected Information Element is not a protocol error. When the maximum count is reached, this counter wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniLmiSequenceErrors 1.3.6.1.4.1.562.36.2.1.71.4.13.1.8
This attribute counts the number of Local Management Interface Status Enquiry message sequence errors. A sequence error is receipt of a Status Enquiry message with a receive sequence number not equal to the last send sequence number. When the maximum count is reached the counter wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniLmiUnexpectedReports 1.3.6.1.4.1.562.36.2.1.71.4.13.1.9
This attribute counts the number of Local Management Interface frames received with an unknown or unexpected report type. An unexpected report type is not a protocol error. When the maximum count is reached the counter wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniLmiPollingVerifTimeouts 1.3.6.1.4.1.562.36.2.1.71.4.13.1.10
This attribute counts the number of checkPointTImer (t392) timer expiries occurring on the Local Management Interface. When the maximum count is reached the counter wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniLmiKeepAliveEnqToIf 1.3.6.1.4.1.562.36.2.1.71.4.13.1.11
This attribute counts the number of Local Management Interface keep alive enquiry status messages sent to the external user device for keep alive status. When the maximum count is reached it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniLmiFullStatusEnqToIf 1.3.6.1.4.1.562.36.2.1.71.4.13.1.12
This attribute counts the number of Local Management Interface full status messages sent to the external user device in response to a status enquiry for keep alive or full status. When the maximum count is reached it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniLmiUserSideEventHistory 1.3.6.1.4.1.562.36.2.1.71.4.13.1.13
This attribute displays the Local Management Interface user side procedure event history in order of occurrence. An event is represented by a single symbol. A '+' symbol indicates a good event. An 'X' symbol indicates a protocol error event. The left most event is the most recent to occur. The provisioned eventCount (nN3/ N393) dictates the maximum number of events displayed. A good event is triggered by receipt of a valid status message. An error event is either a nT1/T391 timer expiry or receipt of a status message with bad sequence numbers.
OBJECT-TYPE    
  AsciiString SIZE(1..10)  

mscFrUniLmiStatusSequenceErrors 1.3.6.1.4.1.562.36.2.1.71.4.13.1.14
This attribute counts the number of Local Management Interface Status message sequence errors. A sequence error is receipt of a Status message with a receive sequence number not equal to the last send sequence number. When the maximum count is reached the counter wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniLmiNoStatusReportCount 1.3.6.1.4.1.562.36.2.1.71.4.13.1.15
This attribute counts the number of times when no status report or an invalid status report comes from the external network. This attribute is incremented in two cases: i) after a status enquiry is sent out and T391 timer expires without having a status report received. ii) an invalid status report is received. When the maximum count is reached it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniLmiUspParmsTable 1.3.6.1.4.1.562.36.2.1.71.4.14
This group contains the provisionable attributes of the Local Management Interface user side procedure.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniLmiUspParmsEntry

mscFrUniLmiUspParmsEntry 1.3.6.1.4.1.562.36.2.1.71.4.14.1
An entry in the mscFrUniLmiUspParmsTable.
OBJECT-TYPE    
  MscFrUniLmiUspParmsEntry  

mscFrUniLmiFullStatusPollingCycles 1.3.6.1.4.1.562.36.2.1.71.4.14.1.1
This attribute specifies how frequently the Frame Relay UNI service should initiate a Status Enquiry for a full PVC status report. A polling cycle is a Status Enquiry and Status Report exchange. This attribute is used only if the side attribute is either user or both.
OBJECT-TYPE    
  Unsigned32 1..255  

mscFrUniLmiLinkVerificationTimer 1.3.6.1.4.1.562.36.2.1.71.4.14.1.2
This attribute specifies how frequently the Frame Relay UNI service should initiate a Status Enquiry for link integrity verification. It must be less than checkPointTimer (t392). When the Lmi side is network, this attribute is ignored.
OBJECT-TYPE    
  Unsigned32 5 | 10 | 15 | 20 | 25 | 30  

mscFrUniDlci 1.3.6.1.4.1.562.36.2.1.71.5
OBJECT IDENTIFIER    

mscFrUniDlciRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.5.1
This entry controls the addition and deletion of mscFrUniDlci components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciRowStatusEntry

mscFrUniDlciRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.5.1.1
A single entry in the table represents a single mscFrUniDlci component.
OBJECT-TYPE    
  MscFrUniDlciRowStatusEntry  

mscFrUniDlciRowStatus 1.3.6.1.4.1.562.36.2.1.71.5.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniDlci components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniDlciComponentName 1.3.6.1.4.1.562.36.2.1.71.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniDlciStorageType 1.3.6.1.4.1.562.36.2.1.71.5.1.1.4
This variable represents the storage type value for the mscFrUniDlci tables.
OBJECT-TYPE    
  StorageType  

mscFrUniDlciIndex 1.3.6.1.4.1.562.36.2.1.71.5.1.1.10
This variable represents the index for the mscFrUniDlci tables.
OBJECT-TYPE    
  Integer32 16..1007  

mscFrUniDlciDc 1.3.6.1.4.1.562.36.2.1.71.5.2
OBJECT IDENTIFIER    

mscFrUniDlciDcRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.5.2.1
This entry controls the addition and deletion of mscFrUniDlciDc components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciDcRowStatusEntry

mscFrUniDlciDcRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.5.2.1.1
A single entry in the table represents a single mscFrUniDlciDc component.
OBJECT-TYPE    
  MscFrUniDlciDcRowStatusEntry  

mscFrUniDlciDcRowStatus 1.3.6.1.4.1.562.36.2.1.71.5.2.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniDlciDc components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniDlciDcComponentName 1.3.6.1.4.1.562.36.2.1.71.5.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniDlciDcStorageType 1.3.6.1.4.1.562.36.2.1.71.5.2.1.1.4
This variable represents the storage type value for the mscFrUniDlciDc tables.
OBJECT-TYPE    
  StorageType  

mscFrUniDlciDcIndex 1.3.6.1.4.1.562.36.2.1.71.5.2.1.1.10
This variable represents the index for the mscFrUniDlciDc tables.
OBJECT-TYPE    
  NonReplicated  

mscFrUniDlciDcOptionsTable 1.3.6.1.4.1.562.36.2.1.71.5.2.10
This group defines attributes associated with a direct call. It defines connection in terms of path and call option parameters. This connection can be permanent (PVC), switched (SVC), or switched permanent (SPVC). It can have four facilities: - CCITT Facilities - DTE Facilities - National Facilities - International Facilities The total number of bytes of facilities including the facility codes and all of the facility data from all of the four classes of facilities must not exceed 512 bytes.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciDcOptionsEntry

mscFrUniDlciDcOptionsEntry 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1
An entry in the mscFrUniDlciDcOptionsTable.
OBJECT-TYPE    
  MscFrUniDlciDcOptionsEntry  

mscFrUniDlciDcRemoteNpi 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.3
This attribute specifies the Numbering Plan Indicator (NPI) of the remoteDna.
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

mscFrUniDlciDcRemoteDna 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.4
This attribute specifies the Data Network Address (DNA) of the service at the remote end of the DLCI. This is the called (destination) DCE address (DNA) of this PVC.
OBJECT-TYPE    
  DigitString SIZE(1..15)  

mscFrUniDlciDcRemoteDlci 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.5
This attribute specifies the remote DLCI of the PVC connection.
OBJECT-TYPE    
  Unsigned32 16..1007  

mscFrUniDlciDcType 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.6
This attribute specifies the type of VC call. If the value is set to permanentMaster, then a permanent connection will be established between two ends. The remote end must be defined as a permanentSlave, permanentBackupSlave, or permanentSlaveWithBackup. The connection cannot be established if the remote end is defined as anything else. The end defined as permanentMaster always initiates the calls. It attempts to call once per minute. If the value is set to permanentSlave then a permanent connection will be established between two ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote end is defined as anything else. The permanentSlave end attempts to call once per minute. If the value is set to permanentSlaveWithBackup then a permanent connection will be established between the two ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote interface is defined as anything else. The permanentSlaveWithBackup attempts to call once per minute. When type is set to permanentSlaveWithBackup, the connection is cleared if the interface becomes unavailable. This enables a retry of the connection which can be redirected to the permanentBackupSlave. If the value is set to permanentBackupSlave then a permanent connection is established between the two ends only if the permanentMaster end is disconnected from the permanentSlaveWithBackup end and a backup call is established by the call redirection system. If the permanentSlaveWithBackup interface becomes available again, the permanentBackupSlave end is disconnected and the permanentSlaveWithBackup end is reconnected to the permanentMaster end. The permanentBackupSlave end does not try to establish a call. If the value is set to spvcMaster, then a permanent connection is established between two ends, with resiliency at the NNI), if the connection transits across two or more networks. The remote end, which may be in the same network, or an external network that is reachable via Frame Relay NNIs, must be defined as either a spvcSlave, spvcBackupSlave or spvcSlaveWithBackup. The connection cannot be established if the remote end is defined as anything else. The end defined as spvcMaster always initiates the call. It attempts to call once per minute. The call is attempted by the spvcMaster and accepted by the remote end only if all of the following conditions are satisfied, at both ends: 1. The physical layer must be operational. 2. The LMI procedures must be in normalCondition (that is, no service affecting condition). 3. If the LMI side attribute is provisioned to both, the A-bit received from the interface must be Active. If the LMI side attribute is not provisioned to both, this condition does not apply. After a call is cleared, the spvcMaster end attempts to retry the call according to the rule for the clear cause. If the call is cleared or rejected due to the failure of one of the three conditions indicated above, or due to unavailability of resources along any point in the connection path, the call will be retried after 60 seconds. For all other causes, such as loss of service at an NNI, the call will be retried immediately. If the value is set to spvcSlave then an SPVC connection is established between two ends. The remote end must be defined as an spvcMaster. The connection cannot be established if the remote end is defined as anything else. The spvcSlave end does not attempt to call. If the value is set to spvcSlaveWithBackup then a SPVC connection is established between the two ends. The remote end must be defined as an spvcMaster. The connection cannot be established if the remote interface end is defined as anything else. Unlike a permanentSlaveWithBackup end, the spvcSlaveWithBackup end does not attempt to call. If the value is set to spvcSlaveWithBackup, the connection is cleared if the interface becomes unavailable. This enables a retry of the connection by the spvcMaster end, which may be redirected to an end that is set to spvcBackupSlave. If the value is set to spvcBackupSlave then an SPVC connection is established between the two ends only if the spvcMaster end is disconnected from the spvcSlaveWithBackup end, and a backup call is redirected by the call redirection system. Unlike the PVC connection, if the spvcSlaveWithBackup interface becomes available again, the spvcBackupSlave end is not disconnected and the spvcSlaveWithBackup end is not reconnected to the spvcMaster end. Neither the spvcBackupSlave nor the spvcSlaveWithBackup ends try to establish an SPVC call.
OBJECT-TYPE    
  INTEGER permanentMaster(1), permanentSlave(2), permanentBackupSlave(3), permanentSlaveWithBackup(4), spvcMaster(5), spvcSlave(6), spvcBackupSlave(7), spvcSlaveWithBackup(8)  

mscFrUniDlciDcTransferPriority 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.9
This attribute specifies the transfer priority to the local network for the outgoing calls using this particular DLCI. It overrides the defaultTransferPriority provisioned in its associated Dna component. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 levels from 0 to 15. Each transfer priority n, where n is the transfer priority index, has a default setting for routing class of service (multimedia, delay, or throughput) and Frame Relay egress queue (depending on the number of supported egress queues on the remote end interface). These settings are specified by the routingClassOfService and emissionPriority attributes provisioned under the Mod Frs DprsNet Tpm/n component. Specifying useDnaDefTP means using the value given by defaultTransferPriority in the associated Dna for this DLCI.
OBJECT-TYPE    
  INTEGER n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15), useDnaDefTP(255)  

mscFrUniDlciDcDiscardPriority 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.10
This attribute specifies the discard priority for outgoing call using this DLCI. The discard priority has three provisioning values: normal, high, and useDnaDefPriority. Under congestion conditions, traffic with normal priority is discarded before traffic with high priority. The Dna default value (provisioned by outDefaultPriority) is taken if this attribute is set to the value useDnaDefPriority.
OBJECT-TYPE    
  INTEGER normal(0), high(1), useDnaDefPriority(3)  

mscFrUniDlciDcDeDiscardPriority 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.11
This attribute specifies whether the discardPriority applies to DE frames for this DLCI. When set to determinedByDiscardPriority, traffic with DE bit set will be discarded according to the setting of the discardPriority. When set to lowest, all traffic with DE bit set is treated the same and is sent to the subnet at the lowest discard priority.
OBJECT-TYPE    
  INTEGER lowest(0), determinedByDiscardPriority(1)  

mscFrUniDlciDcDataPath 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.12
This attribute specifies the data path to be used by Virtual Circuits on this interface. The value of the dataPath attribute in the Dna component is overridden by this attribute if the value is not useDnaValue. This value applies to the connection after data transfer state is reached. All the data and control traffic will be sent using this data path. If the provisioned dataPath is not available the connection is not established. The value of the dataPath is signalled by both ends of the connection. If this value is not the same at both ends dprsOnly is used for the duration of the connection. A virtual circuit connection is always established using dprsOnly even if this attribute is provisioned as some other value. dprsOnly - The dynamic packet routing system is used. dprsMcsOnly - The DPRS Multi-Service Cut-Through Switching path is used. dprsMcsFirst - The DPRS Multi-Service Cut-Through Switching path is used if it is available. If it is not available, dprsOnly is used. useDnaValue - The routing system used is based on the value provisioned in the Dna component.
OBJECT-TYPE    
  INTEGER dprsOnly(0), dprsMcsOnly(1), dprsMcsFirst(2), useDnaValue(3)  

mscFrUniDlciDcCugIndex 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.13
This attribute specifies the CUG index which is to be signalled in PVC and SPVC call requests to the remote end. The type of CUG signalling is defined in attribute cugType in this component.
OBJECT-TYPE    
  Unsigned32 0..255  

mscFrUniDlciDcCugType 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.14
This attribute specifies the type of CUG signalling to be used in PVC and SPVC call requests. Index of CUG to be used is defined in attribute cugIndex in this component. Possible values are: cug - signal CUG cugOa - signal CUG with outgoing access doNotSignal - no CUG in call request
OBJECT-TYPE    
  INTEGER doNotSignal(0), cug(3), cugOa(9)  

mscFrUniDlciDcMapIpCosToFrQos 1.3.6.1.4.1.562.36.2.1.71.5.2.10.1.15
This attribute specifies whether an IP TOS value is mapped to an FR QOS. The mapping used is provisioned in the Mod Frs IpCosToFrQos component. When this attribute is set to yes, at Frame Relay egress, the IP TOS byte in each frame is checked. The TOS value determines the egress emission queue and the discard priority for that frame. When this attribute is set to no, FR QOS is determined by the provisioned discard priority and transfer priority.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mscFrUniDlciDcNfaTable 1.3.6.1.4.1.562.36.2.1.71.5.2.202
This is the i'th National facility required for this direct call. Within the provisioning system, the user specifies the facility code along with the facility parameters. The facility is represented internally as a hexadecimal string following the X.25 ITU-T representation for facility data. Two explicit attributes discardPriority and pathSensitivity are created to replace H.01 and H.30 in the group VcsDirectCallOptionsProv of this file. The migrate escape here (DcComponent::migrateFaxEscape) propagates the old provisioning data under H.01 and H.30 into discardPriority and transferPriority. The rule of the above propagation are: 0 in H.01 is equivalent to discardPriority 0; 1 in H.01 is equivalent to discardPriority 1. And 0 in H.30 is equivalent to transferPriority throughput; 1 in H.30 is equivalent to pathSensitivity delay. Please refer to discardPriority and pathSensitivity for more information on how to use them.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciDcNfaEntry

mscFrUniDlciDcNfaEntry 1.3.6.1.4.1.562.36.2.1.71.5.2.202.1
An entry in the mscFrUniDlciDcNfaTable.
OBJECT-TYPE    
  MscFrUniDlciDcNfaEntry  

mscFrUniDlciDcNfaIndex 1.3.6.1.4.1.562.36.2.1.71.5.2.202.1.1
This variable represents the index for the mscFrUniDlciDcNfaTable.
OBJECT-TYPE    
  Integer32 1 | 48  

mscFrUniDlciDcNfaValue 1.3.6.1.4.1.562.36.2.1.71.5.2.202.1.2
This variable represents an individual value for the mscFrUniDlciDcNfaTable.
OBJECT-TYPE    
  HexString SIZE(0..128)  

mscFrUniDlciDcNfaRowStatus 1.3.6.1.4.1.562.36.2.1.71.5.2.202.1.3
This variable is used to control the addition and deletion of individual values of the mscFrUniDlciDcNfaTable.
OBJECT-TYPE    
  RowStatus  

mscFrUniDlciVc 1.3.6.1.4.1.562.36.2.1.71.5.3
OBJECT IDENTIFIER    

mscFrUniDlciVcRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.5.3.1
This entry controls the addition and deletion of mscFrUniDlciVc components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciVcRowStatusEntry

mscFrUniDlciVcRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.5.3.1.1
A single entry in the table represents a single mscFrUniDlciVc component.
OBJECT-TYPE    
  MscFrUniDlciVcRowStatusEntry  

mscFrUniDlciVcRowStatus 1.3.6.1.4.1.562.36.2.1.71.5.3.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniDlciVc components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniDlciVcComponentName 1.3.6.1.4.1.562.36.2.1.71.5.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniDlciVcStorageType 1.3.6.1.4.1.562.36.2.1.71.5.3.1.1.4
This variable represents the storage type value for the mscFrUniDlciVc tables.
OBJECT-TYPE    
  StorageType  

mscFrUniDlciVcIndex 1.3.6.1.4.1.562.36.2.1.71.5.3.1.1.10
This variable represents the index for the mscFrUniDlciVc tables.
OBJECT-TYPE    
  NonReplicated  

mscFrUniDlciVcCadTable 1.3.6.1.4.1.562.36.2.1.71.5.3.10
This group represents operational call data related to Frame Relay Vc. It can be displayed only for Frame Relay Vc which is created by application.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciVcCadEntry

mscFrUniDlciVcCadEntry 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1
An entry in the mscFrUniDlciVcCadTable.
OBJECT-TYPE    
  MscFrUniDlciVcCadEntry  

mscFrUniDlciVcType 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.1
This attribute displays the type of call, pvc,svc,spvc or frf10spvc.
OBJECT-TYPE    
  INTEGER svc(0), pvc(1), spvc(2), frf10spvc(3)  

mscFrUniDlciVcState 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.2
This attribute displays the state of call control. P5 state is not supported but is listed for completness. Transitions from one state to another take very short time. state most often displayed is dataTransferP4.
OBJECT-TYPE    
  INTEGER creating(0), readyP1(1), dteWaitingP2(2), dceWaitingP3(3), dataTransferP4(4), unsupportedP5(5), dteClearRequestP6(6), dceClearIndicationP7(7), termination(8)  

mscFrUniDlciVcPreviousState 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.3
This attribute displays the previous state of call control. This is a valuable field to determine how the processing is progressing.
OBJECT-TYPE    
  INTEGER creating(0), readyP1(1), dteWaitingP2(2), dceWaitingP3(3), dataTransferP4(4), unsupportedP5(5), dteClearRequestP6(6), dceClearIndicationP7(7), termination(8)  

mscFrUniDlciVcDiagnosticCode 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.4
This attribute displays the internal substate of call control. It is used to further refine state of call processing.
OBJECT-TYPE    
  Unsigned32 0..255  

mscFrUniDlciVcPreviousDiagnosticCode 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.5
This attribute displays the internal substate of call control. It is used to further refine state of call processing.
OBJECT-TYPE    
  Unsigned32 0..255  

mscFrUniDlciVcCalledNpi 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.6
This attribute displays the Numbering Plan Indicator (NPI) of the called end.
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

mscFrUniDlciVcCalledDna 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.7
This attribute displays the Data Network Address (Dna) of the called (destination) DTE to which this call is sent. This address if defined at recieving end will complete Vc connection.
OBJECT-TYPE    
  DigitString SIZE(1..15)  

mscFrUniDlciVcCalledLcn 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.8
This attribute displays the Logical Channel Number of the called end. It is valid only after both ends of Vc exchanged relevant information.
OBJECT-TYPE    
  Unsigned32 1..65535  

mscFrUniDlciVcCallingNpi 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.9
This attribute displays the Numbering Plan Indicator (NPI) of the calling end.
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

mscFrUniDlciVcCallingDna 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.10
This attribute displays the Data Network Address (Dna) of the calling end.
OBJECT-TYPE    
  DigitString SIZE(1..15)  

mscFrUniDlciVcCallingLcn 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.11
This attribute displays the Logical Channel Number of the calling end.
OBJECT-TYPE    
  Unsigned32 1..65535  

mscFrUniDlciVcAccountingEnabled 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.12
This attribute indicates that this optional section of accounting record is suppressed or permitted. If accountingEnabled is yes, conditions for generation of accounting record were met. These conditions include billing options, vc recovery conditions and Module wide accounting data options.
OBJECT-TYPE    
  INTEGER yes(0), no(1)  

mscFrUniDlciVcFastSelectCall 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.13
This attribute displays that this is a fast select call.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mscFrUniDlciVcPathReliability 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.19
This attribute displays the path reliability.
OBJECT-TYPE    
  INTEGER high(0), normal(1)  

mscFrUniDlciVcAccountingEnd 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.20
This attribute indicates if this end should generate an accounting record. Normally, callingEnd is the end to generate an accounting record.
OBJECT-TYPE    
  INTEGER callingEnd(0), calledEnd(1)  

mscFrUniDlciVcPriority 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.21
This attribute displays whether the call is a normal or a high priority call.
OBJECT-TYPE    
  INTEGER normal(0), high(1)  

mscFrUniDlciVcSegmentSize 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.22
This attribute displays the segment size (in bytes) used on the call. It is used to calculate the number of segments transmitted and received.
OBJECT-TYPE    
  Unsigned32 0..4096  

mscFrUniDlciVcMaxSubnetPktSize 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.27
This attribute indicates the maximum packet size allowed on the Vc.
OBJECT-TYPE    
  Unsigned32 0..4096  

mscFrUniDlciVcRcosToNetwork 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.28
This attribute indicates the routing metric routing class of service to the network.
OBJECT-TYPE    
  INTEGER throughput(0), delay(1), multimedia(2)  

mscFrUniDlciVcRcosFromNetwork 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.29
This attribute displays the routing metric Routing Class of Service from the Network.
OBJECT-TYPE    
  INTEGER throughput(0), delay(1), multimedia(2)  

mscFrUniDlciVcEmissionPriorityToNetwork 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.30
This attribute displays the network internal emission priotity to the network.
OBJECT-TYPE    
  INTEGER normal(0), high(1), interrupting(2)  

mscFrUniDlciVcEmissionPriorityFromNetwork 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.31
This attribute displays the network internal emission priotity from the network.
OBJECT-TYPE    
  INTEGER normal(0), high(1), interrupting(2)  

mscFrUniDlciVcDataPath 1.3.6.1.4.1.562.36.2.1.71.5.3.10.1.32
This attribute indicates the data path used by the connection. The data path is provisioned in Dna and DirectCall components. The displayed value of this attribute can be different from the provisioned value. If the connection is using dprsOnly data path, the string dprsOnly is displayed. (dynamic packet routing system) If the connection is using dprsMcsOnly data path, the string dprsMcsOnly is displayed. If the connection is using dprsMcsFirst data path, the string dprsMcsFirst is displayed.
OBJECT-TYPE    
  AsciiString SIZE(0..32)  

mscFrUniDlciVcIntdTable 1.3.6.1.4.1.562.36.2.1.71.5.3.11
This group defines display of interval data collected by Vc. Data in this group is variable and may depend on time when this display command is issued.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciVcIntdEntry

mscFrUniDlciVcIntdEntry 1.3.6.1.4.1.562.36.2.1.71.5.3.11.1
An entry in the mscFrUniDlciVcIntdTable.
OBJECT-TYPE    
  MscFrUniDlciVcIntdEntry  

mscFrUniDlciVcCallReferenceNumber 1.3.6.1.4.1.562.36.2.1.71.5.3.11.1.1
This attribute is obsolete. It is replaced by the callReferenceNumber attribute to display the call reference number in decimal. The SNMP reference for the callReferenceNumber attribute is callReferenceNumberDecimal.
OBJECT-TYPE    
  Hex 0..16777215  

mscFrUniDlciVcElapsedTimeTillNow 1.3.6.1.4.1.562.36.2.1.71.5.3.11.1.2
This attribute displays the elapsed time representing the period of this interval data. It is elapsed time in 0.1 second increments since Vc started.
OBJECT-TYPE    
  Unsigned32 0..16777215  

mscFrUniDlciVcSegmentsRx 1.3.6.1.4.1.562.36.2.1.71.5.3.11.1.3
This attribute displays the number of segments received at the time command was issued. This is the segment received count maintained by accounting at each end of the Vc. This counter is updated only when the packet cannot be successfully delivered out of the sink Vc and to the sink AP Conditions in which packets may be discarded by the sink Vc include: missing packets due to subnet discards, segmentation protocol violations due to subnet discard, duplicated and out-of-ranged packets and packets that arrive while Vc is in path recovery state.
OBJECT-TYPE    
  Unsigned32 0..16777215  

mscFrUniDlciVcSegmentsSent 1.3.6.1.4.1.562.36.2.1.71.5.3.11.1.4
This attribute displays the number of segments sent at the time command was issued. This is the segment sent count maintained by accounting at the source Vc. Vc only counts packets that Vc thinks can be delivered successfully into the subnet. In reality, these packets may be dropped by trunking, for instance. This counter is not updated when splitting fails, when Vc is in a path recovery state, when packet forwarding fails to forward this packet and when subsequent packets have to be discarded as we want to minimize the chance of out-of-sequence and do not intentionally send out-of- sequenced packets into the subnet.
OBJECT-TYPE    
  Unsigned32 0..16777215  

mscFrUniDlciVcStartTime 1.3.6.1.4.1.562.36.2.1.71.5.3.11.1.5
This attribute displays the start time of this interval period. If Vc spans 12 hour time or time of day change startTime reflects new time as recorded at 12 hour periods or time of day changes.
OBJECT-TYPE    
  EnterpriseDateAndTime SIZE(0 | 19)  

mscFrUniDlciVcCallReferenceNumberDecimal 1.3.6.1.4.1.562.36.2.1.71.5.3.11.1.7
This attribute displays the call reference number which is a unique number generated by the switch.The same Call Reference Number is stored in the interval data (accounting record) at both ends of the call. It can be used as one of the attributes in matching duplicate records generated at each end of the call.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciVcFrdTable 1.3.6.1.4.1.562.36.2.1.71.5.3.12
This group defines Frame Relay attributes collected by Frame Relay Vc. The purpose of Vc attributes is to aid end users and verification people to understand the Vc internal behavior. This is particularly useful when the network has experienced abnormality and we want to isolate problems and pinpoint trouble spots. Attributes are collected on a per Vc basis. Until a need is identified, statistics are not collected at a processor level. Each attribute is stored in a 32 bit field and is initialized to zero when a Vc enters into the data transfer state. When a PVC is disconnected and then connected again, the attributes will be reset. Attributes cannot be reset through other methods. Frame Relay Vc uses a best effort data packet delivery protocol and a different packet segmentation and combination methods from the General Vc. The Frame Relay Vc uses the same call setup and control mechanism (e.g. the support of non-flow control data packets) as in a General Vc. Most General Vc statistics and internal variables are used in a Frame Relay Vc and are displayed by software developers
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciVcFrdEntry

mscFrUniDlciVcFrdEntry 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1
An entry in the mscFrUniDlciVcFrdTable.
OBJECT-TYPE    
  MscFrUniDlciVcFrdEntry  

mscFrUniDlciVcFrmCongestedToSubnet 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.2
This attribute displays the number of frames from link discarded due to lack of resources. It keeps track of the number of frames from link that have to be discarded. The discard reasons include insufficient memory for splitting the frame into smaller subnet packet size.
OBJECT-TYPE    
  Unsigned32 0..5000  

mscFrUniDlciVcCannotForwardToSubnet 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.3
This attribute displays the number of discarded packets that can not be forwarded into the subnet because of subnet congestion. Number of frames from link discarded due to failure in forwarding a packet from Vc into the subnet.- This attribute is increased when packet forwarding fails to forward a packet into the subnet. If a frame is split into multiple subnet packets and a partial packet has to be discarded, all subsequent partial packets that have not yet been delivered to the subnet will be discarded as well.
OBJECT-TYPE    
  Unsigned32 0..5000  

mscFrUniDlciVcNotDataXferToSubnet 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.4
This attribute records the number of frames from link discarded when the Vc tries to recover from internal path failure.
OBJECT-TYPE    
  Unsigned32 0..5000  

mscFrUniDlciVcOutOfRangeFrmFromSubnet 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.5
This attribute displays the number of frames from subnet discarded due to out of sequence range for arriving too late.
OBJECT-TYPE    
  Unsigned32 0..5000  

mscFrUniDlciVcCombErrorsFromSubnet 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.6
This attribute records the number of subnet packets discarded at the sink Vc due to the Vc segmentation and combination protocol error. Usually, this occurs when the subnet discards packets and thus this statistics can be used to guest the number of subnet packets that are not delivered to the Vc. It cannot be used as an actual measure because some subnet packets may have been delivered to Vc but have to be discarded because these are partial packets to a frame in which some other partial packets have not been properly delivered to Vc
OBJECT-TYPE    
  Unsigned32 0..5000  

mscFrUniDlciVcDuplicatesFromSubnet 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.7
This attribute displays the number of subnet packets discarded due to duplication. Although packets are not retransmitted by the Frame Relay Vc, it is possible for the subnet to retransmit packets. When packets are out-of-sequenced and copies of the same packets arrive, then this attribute is increased.
OBJECT-TYPE    
  Unsigned32 0..5000  

mscFrUniDlciVcNotDataXferFromSubnet 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.8
This attribute displays the number of subnet packets discarded when data transfer is suspended in Vc recovery.
OBJECT-TYPE    
  Unsigned32 0..5000  

mscFrUniDlciVcFrmLossTimeouts 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.9
This attribute displays the number of lost frame timer expiries. When this count is excessive, the network is very congested and packets have been discarded in the subnet.
OBJECT-TYPE    
  Unsigned32 0..5000  

mscFrUniDlciVcOoSeqByteCntExceeded 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.10
This attribute displays the number times that the out of sequence byte threshold is exceeded. When the threshold is exceeded, this condition is treated as if the loss frame timer has expired and all frames queued at the sink Vc are delivered to the AP. We need to keep this count to examine if the threshold is engineered properly. This should be used in conjunction with the peak value of out-of- sequenced queue and the number of times the loss frame timer has expired. This count should be relatively small when compared with loss frame timer expiry count.
OBJECT-TYPE    
  Unsigned32 0..5000  

mscFrUniDlciVcPeakOoSeqPktCount 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.11
This attribute displays the frame relay peak packet count of the out of sequence queue. This attribute records the maximum queue length of the out-of-sequenced queue. The counter can be used to deduce the message buffer requirement on a Vc.
OBJECT-TYPE    
  Unsigned32 0..5000  

mscFrUniDlciVcPeakOoSeqFrmForwarded 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.12
This attribute displays the frame relay peak size of the sequence packet queue. The subnet may deliver packets out-of- sequenced. These packets are then queued in an out-of-sequenced queue, waiting for a packet with the expected sequence number to come. When that packet arrives, this attribute records the maximum number of packets that were out-of-sequenced, but now have become in-sequenced. The statistics is used to measure expected queue size due to normal subnet packet disorder (not due to subnet packet discard). Current implementation also uses this statistics to set a maximum size for the out-of-sequenced queue.
OBJECT-TYPE    
  Unsigned32 0..5000  

mscFrUniDlciVcSendSequenceNumber 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.13
This attribute displays the Vc internal packet's send sequence number. Note that a 'packet' in this context, may be either a user data packet, or an OAM frame.
OBJECT-TYPE    
  Unsigned32 0..5000  

mscFrUniDlciVcPktRetryTimeouts 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.15
This attribute displays the number of packets which have retransmission time-outs. When this count is excessive, the network is very congested and packets have been discarded in the subnet.
OBJECT-TYPE    
  Unsigned32 0..5000  

mscFrUniDlciVcPeakRetryQueueSize 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.16
This attribute displays the peak size of retransmission queue. This attribute is used as an indicator of the acknowledgment behavior across the subnet. Records the largest body of unacknowledged packets.
OBJECT-TYPE    
  Unsigned32 0..5000  

mscFrUniDlciVcSubnetRecoveries 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.17
This attribute displays the number of successful Vc recovery attempts.
OBJECT-TYPE    
  Unsigned32 0..5000  

mscFrUniDlciVcOoSeqPktCntExceeded 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.19
This attribute displays the number times that the out of sequence packet threshold is exceeded. When the threshold is exceeded, this condition is treated as if the loss frame timer has expired and all frames queued at the sink Vc are delivered to the AP. We need to keep this count to examine if the threshold is engineered properly. This should be used in conjunction with the peak value of out-of- sequenced queue and the number of times the loss frame timer has expired. This count should be relatively small when compared with loss frame timer expiry count.
OBJECT-TYPE    
  Unsigned32 0..255  

mscFrUniDlciVcPeakOoSeqByteCount 1.3.6.1.4.1.562.36.2.1.71.5.3.12.1.20
This attribute displays the frame relay peak byte count of the out of sequence queue. This attribute records the maximum queue length of the out-of-sequenced queue. The counter can be used to deduce the message buffer requirement on a Vc.
OBJECT-TYPE    
  Unsigned32 0..50000  

mscFrUniDlciVcDmepTable 1.3.6.1.4.1.562.36.2.1.71.5.3.417
This attribute displays the data path used by the connection. Data path is provisioned in Dna and DirectCall components. If the connection is using dprsOnly data path, this attribute is empty. If the connection is using dprsMcsOnly or dprsMcsFirst data path, this attribute displays component name of the dprsMcsEndPoint.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciVcDmepEntry

mscFrUniDlciVcDmepEntry 1.3.6.1.4.1.562.36.2.1.71.5.3.417.1
An entry in the mscFrUniDlciVcDmepTable.
OBJECT-TYPE    
  MscFrUniDlciVcDmepEntry  

mscFrUniDlciVcDmepValue 1.3.6.1.4.1.562.36.2.1.71.5.3.417.1.1
This variable represents both the value and the index for the mscFrUniDlciVcDmepTable.
OBJECT-TYPE    
  RowPointer  

mscFrUniDlciSp 1.3.6.1.4.1.562.36.2.1.71.5.4
OBJECT IDENTIFIER    

mscFrUniDlciSpRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.5.4.1
This entry controls the addition and deletion of mscFrUniDlciSp components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciSpRowStatusEntry

mscFrUniDlciSpRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.5.4.1.1
A single entry in the table represents a single mscFrUniDlciSp component.
OBJECT-TYPE    
  MscFrUniDlciSpRowStatusEntry  

mscFrUniDlciSpRowStatus 1.3.6.1.4.1.562.36.2.1.71.5.4.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniDlciSp components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniDlciSpComponentName 1.3.6.1.4.1.562.36.2.1.71.5.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniDlciSpStorageType 1.3.6.1.4.1.562.36.2.1.71.5.4.1.1.4
This variable represents the storage type value for the mscFrUniDlciSp tables.
OBJECT-TYPE    
  StorageType  

mscFrUniDlciSpIndex 1.3.6.1.4.1.562.36.2.1.71.5.4.1.1.10
This variable represents the index for the mscFrUniDlciSp tables.
OBJECT-TYPE    
  NonReplicated  

mscFrUniDlciSpParmsTable 1.3.6.1.4.1.562.36.2.1.71.5.4.11
This group contains the provisionable attributes for the Data Link Connection Identifier. These attributes reflect the service parameters specific to this instance of DLCI. The congestion control attributes in this group are defined in T1.606 Addendum 1.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciSpParmsEntry

mscFrUniDlciSpParmsEntry 1.3.6.1.4.1.562.36.2.1.71.5.4.11.1
An entry in the mscFrUniDlciSpParmsTable.
OBJECT-TYPE    
  MscFrUniDlciSpParmsEntry  

mscFrUniDlciSpMaximumFrameSize 1.3.6.1.4.1.562.36.2.1.71.5.4.11.1.1
This attribute specifies the maximum number of octets which may be included in the information field. The frame relay header and CRC octets are not included in this definition. This attribute corresponds to the dN1 parameter described in the Vendor Forum Specification.
OBJECT-TYPE    
  Unsigned32 1..8187  

mscFrUniDlciSpRateEnforcement 1.3.6.1.4.1.562.36.2.1.71.5.4.11.1.2
This attribute specifies whether rate enforcement is in effect for this user Data Link Connection on this Frame Relay interface. Turning on rate enforcement means that CIR and DE=1 traffic will be measured and enforced. Turning off rate enforcement means that all frames from the user will be accepted and no modifications to the frame with respect to the DE bit will be made.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscFrUniDlciSpCommittedInformationRate 1.3.6.1.4.1.562.36.2.1.71.5.4.11.1.3
This attribute specifies the committed information rate (CIR) in bits per second (bit/s). When rateEnforcement is set to on, cir is the rate at which the network agrees to transfer information under normal conditions. This rate is measured over a measurement interval (t) that is determined internally based on CIR and the committed burst size (Bc). An exception to this occurs when CIR is provisioned to be zero, in which case the measurement interval (t) must be provisioned explicitly. This attribute is ignored when rateEnforcement is off. If rateEnforcement is on and this attribute is 0, Bc must also be 0.
OBJECT-TYPE    
  Gauge32 0..50000000  

mscFrUniDlciSpCommittedBurstSize 1.3.6.1.4.1.562.36.2.1.71.5.4.11.1.4
This attribute specifies the committed burst size (Bc) in bits. bc is the amount of data that a network agrees to transfer under normal conditions over a measurement interval (t). Data marked DE=1 is not accounted for in Bc. This attribute is ignored when rateEnforcement is off. If rateEnforcement is on and this attribute is 0, cir must also be 0.
OBJECT-TYPE    
  Gauge32 0..50000000  

mscFrUniDlciSpExcessBurstSize 1.3.6.1.4.1.562.36.2.1.71.5.4.11.1.5
This attribute specifies the excess burst size (Be) in bits. Be is the amount of uncommitted data that the network will attempt to deliver over measurement interval T. Data marked DE=1 by the user or by the network is accounted for here. CIR, Bc, and Be cannot all be zero when rateEnforcement is on.
OBJECT-TYPE    
  Gauge32 0..50000000  

mscFrUniDlciSpMeasurementInterval 1.3.6.1.4.1.562.36.2.1.71.5.4.11.1.6
When cir and bc are zero and rateEnforcement is on, this attribute must be provisioned to specify the time interval (in milliseconds) over which rates and burst sizes are measured. When cir and bc are non-zero, the time interval is internally calculated and is not shown. In that situation, this field is ignored, and is not representative of the time interval. This attribute is ignored when rateEnforcement is off, or when cir and bc are non-zero. If rateEnforcement is on and both cir and bc are zero, this field must be non-zero.
OBJECT-TYPE    
  Unsigned32 0..25500  

mscFrUniDlciSpRateAdaptation 1.3.6.1.4.1.562.36.2.1.71.5.4.11.1.7
This attribute specifies whether rate adaptation is in effect for this user Data Link Connection on this Frame Relay interface. Rate adaptation is a feature that, in periods of congestion, adapts the rate at which the user is allowed to send data into the network to that which the network is able to handle at that time. This pro-active measure of handling congestion optimizes network resources by causing the ingress to discard frames that would otherwise be discarded in the network. If this attribute is set to on, then, at the onset of congestion, the excess information rate (EIR) is reduced to a very low rate. If congestion persists, then the allowed CIR is reduced geometrically by 25% of the current value at that time. The minimum to which CIR can be reduced is 1/16th (6.25%) of the provisioned value. As congestion alleviates, CIR is increased linearly by 6.25% of the provisioned value specified in committedInformationRate. If set to eirOnly, then rate adaptation will only apply to the excess information rate (EIR). At the onset of congestion, the allowed EIR is reduced by 25% of its provisioned value. If congestion persists, EIR is reduced geometrically by 25% of the current value at that time. As congestion alleviates, EIR is gradually increased linearly by 6.25% of the provisioned EIR. If set to cirProportionate, then rate adaptation will also only apply to the excess information rate (EIR). At the onset of congestion the initial allowed EIR is set to a multiple of the provisioned CIR. If congestion persists, the allowed EIR is reduced geometrically by 25% of the current value at that time. As congestion alleviates, EIR is gradually increased linearly by 6.25% of the provisioned EIR. Note that the allowed EIR may be set higher than the provisioned EIR, since it is calculated initially using another parameter, the provisioned CIR. If the allowed EIR at the moment is higher than the provisioned EIR, then the provisioned EIR is used instead. This attribute can only be set to on eirOnly or cirProportionate if rateEnforcement is turned on.
OBJECT-TYPE    
  INTEGER off(0), on(1), eirOnly(2), cirProportionate(3)  

mscFrUniDlciSpAccounting 1.3.6.1.4.1.562.36.2.1.71.5.4.11.1.8
This attribute specifies whether accounting data collection and record generation is turned on at this DLCI. For accounting data collection and record generation to be turned on, the accountingOn bit and at least one of the accountCollection bits in the DataNetworkAddress component must be set to on.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscFrUniDlciSpRaSensitivity 1.3.6.1.4.1.562.36.2.1.71.5.4.11.1.9
This attribute specifies the sensitivity of the rate adaptation system. A higher number indicates a higher sensitivity and therefore a quicker reaction time to network conditions. A quicker reaction time allows the network to discard frames at the access and protect network resources, but can lead to false alarms and a greater fluctuation of the allowed rate. A higher setting therefore tends to favour the protection of the network over the allowed throughput of the user. A lower number indicates a lower sensitivity and therefore a slower reaction to network conditions. A slower reaction time results in a greater amount of user traffic allowed into the network, but can lead to a waste of network bandwidth since the traffic may be discarded at the congested resource. A lower setting therefore tends to favour the allowed throughput of the user over the protection of the network. This attribute is applicable for adapting EIR when rateAdaptation is eirOnly or cirProportionate, or CIR when rateAdaptation is on. This attribute is ignored if rateAdaptation is turned off.
OBJECT-TYPE    
  Unsigned32 1..20  

mscFrUniDlciSpUpdateBCI 1.3.6.1.4.1.562.36.2.1.71.5.4.11.1.10
This attribute specifies whether internal Backward Congestion Indication (BCI) bits will report congestion external to the Passport network, as communicated through incoming BECN bits. If updateBCI is set to on, then BCI bits for incoming frames will be set if the BECN on the frame is set. If updatBCI is set to off, then incoming BECN bits will have no effect. Setting updateBCI on for a DLCI means that the remote end of the DLCI, which is specified by the remotedna and remotedlci attributes of the dc component of the dlci, may perform Rate Adaptation using the flow of incoming BECN bits, in addition to internal Passport congestion management systems. If the rateAdaptation attribute of the remote dlci is provisioned as eirOnly, cirProportionate, or on, then congestion from another network connected to a Passport network may trigger dynamic congestion management. If the rateAdaptation attribute of the remote dlci is provisioned to off, then the setting of updateBCI attribute here will have no effect..
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscFrUniDlciLb 1.3.6.1.4.1.562.36.2.1.71.5.5
OBJECT IDENTIFIER    

mscFrUniDlciLbRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.5.5.1
This entry controls the addition and deletion of mscFrUniDlciLb components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciLbRowStatusEntry

mscFrUniDlciLbRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.5.5.1.1
A single entry in the table represents a single mscFrUniDlciLb component.
OBJECT-TYPE    
  MscFrUniDlciLbRowStatusEntry  

mscFrUniDlciLbRowStatus 1.3.6.1.4.1.562.36.2.1.71.5.5.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniDlciLb components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniDlciLbComponentName 1.3.6.1.4.1.562.36.2.1.71.5.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniDlciLbStorageType 1.3.6.1.4.1.562.36.2.1.71.5.5.1.1.4
This variable represents the storage type value for the mscFrUniDlciLb tables.
OBJECT-TYPE    
  StorageType  

mscFrUniDlciLbIndex 1.3.6.1.4.1.562.36.2.1.71.5.5.1.1.10
This variable represents the index for the mscFrUniDlciLb tables.
OBJECT-TYPE    
  NonReplicated  

mscFrUniDlciLbStatsTable 1.3.6.1.4.1.562.36.2.1.71.5.5.10
This group contains all the statistics for the data loopback tool.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciLbStatsEntry

mscFrUniDlciLbStatsEntry 1.3.6.1.4.1.562.36.2.1.71.5.5.10.1
An entry in the mscFrUniDlciLbStatsTable.
OBJECT-TYPE    
  MscFrUniDlciLbStatsEntry  

mscFrUniDlciLbLocalTotalFrm 1.3.6.1.4.1.562.36.2.1.71.5.5.10.1.1
This attribute records the number of frames looped back to the link since loopback was last started.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciLbLocalTotalBytes 1.3.6.1.4.1.562.36.2.1.71.5.5.10.1.2
This attribute records the number of bytes looped back to the link since loopback mode was started.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciLbLocalFecnFrm 1.3.6.1.4.1.562.36.2.1.71.5.5.10.1.3
This attribute records the number of frames with the Forward Explicit Congestion Notification (FECN) bit set, looped back to the link since the loopback mode was started.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciLbLocalBecnFrm 1.3.6.1.4.1.562.36.2.1.71.5.5.10.1.4
This attribute records the number of frames with the Backward Explicit Congestion Notification (BECN) bit set, looped back to the link since the loopback mode was started.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciLbLocalDeFrm 1.3.6.1.4.1.562.36.2.1.71.5.5.10.1.5
This attribute records the number of frames with the Discard Eligibility (DE) bit set, looped back to the link since the loopback mode was started.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciLbLocalDeBytes 1.3.6.1.4.1.562.36.2.1.71.5.5.10.1.6
This attribute records the number of bytes in frames with the Discard Eligibility (DE) bit set, looped back to the link since the loopback mode was started.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciLbRemoteTotalFrm 1.3.6.1.4.1.562.36.2.1.71.5.5.10.1.7
This attribute records the number of frames looped back to the subnet since loopback was last started.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciLbRemoteTotalBytes 1.3.6.1.4.1.562.36.2.1.71.5.5.10.1.8
This attribute records the number of bytes looped back to the subnet since loopback was last started.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciLbRemoteFecnFrm 1.3.6.1.4.1.562.36.2.1.71.5.5.10.1.9
This attribute records the number of frames with the Forward Explicit Congestion Notification (FECN) bit set, looped back to the subnet since the loopback mode was started.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciLbRemoteBecnFrm 1.3.6.1.4.1.562.36.2.1.71.5.5.10.1.10
This attribute records the number of frames with the Backward Explicit Congestion Notification (BECN) bit set, looped back to the subnet since the loopback mode was started.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciLbRemoteDeFrm 1.3.6.1.4.1.562.36.2.1.71.5.5.10.1.13
This attribute records the number of frames with the Discard Eligibility (DE) bit set, looped back to the subnet since the loopback mode was started.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciLbRemoteDeBytes 1.3.6.1.4.1.562.36.2.1.71.5.5.10.1.14
This attribute records the number of bytes in frames with the Discard Eligibility (DE) bit set, looped back to the subnet since the loopback mode was started.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciEgressSp 1.3.6.1.4.1.562.36.2.1.71.5.6
OBJECT IDENTIFIER    

mscFrUniDlciEgressSpRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.5.6.1
This entry controls the addition and deletion of mscFrUniDlciEgressSp components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciEgressSpRowStatusEntry

mscFrUniDlciEgressSpRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.5.6.1.1
A single entry in the table represents a single mscFrUniDlciEgressSp component.
OBJECT-TYPE    
  MscFrUniDlciEgressSpRowStatusEntry  

mscFrUniDlciEgressSpRowStatus 1.3.6.1.4.1.562.36.2.1.71.5.6.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniDlciEgressSp components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniDlciEgressSpComponentName 1.3.6.1.4.1.562.36.2.1.71.5.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniDlciEgressSpStorageType 1.3.6.1.4.1.562.36.2.1.71.5.6.1.1.4
This variable represents the storage type value for the mscFrUniDlciEgressSp tables.
OBJECT-TYPE    
  StorageType  

mscFrUniDlciEgressSpIndex 1.3.6.1.4.1.562.36.2.1.71.5.6.1.1.10
This variable represents the index for the mscFrUniDlciEgressSp tables.
OBJECT-TYPE    
  NonReplicated  

mscFrUniDlciEgressSpProvTable 1.3.6.1.4.1.562.36.2.1.71.5.6.10
This group contains the provisionable attributes for this component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciEgressSpProvEntry

mscFrUniDlciEgressSpProvEntry 1.3.6.1.4.1.562.36.2.1.71.5.6.10.1
An entry in the mscFrUniDlciEgressSpProvTable.
OBJECT-TYPE    
  MscFrUniDlciEgressSpProvEntry  

mscFrUniDlciEgressSpCommittedInformationRate 1.3.6.1.4.1.562.36.2.1.71.5.6.10.1.1
This attribute specifies the committed information rate (CIR) for the egress direction. It is used for Call Admission Control (CAC) at the egress link. If the value is set to sameAsSp, the value of this attribute is the same as the committedInformationRate attribute under the ServiceParameters component. VALUES ( 50000001 = sameAsServiceParameters )
OBJECT-TYPE    
  Unsigned32 0..50000000 | 50000001  

mscFrUniDlciEgressSpCommittedBurstSize 1.3.6.1.4.1.562.36.2.1.71.5.6.10.1.2
This attribute specifies the committed burst size (Bc) for the egress direction. It is used for performing Call Admission Control (CAC) at the egress link. If the value is set to sameAsSp, the value of this attribute is the same as the committedBurstSize attribute under the ServiceParameters component. VALUES ( 50000001 = sameAsServiceParameters )
OBJECT-TYPE    
  Unsigned32 0..50000000 | 50000001  

mscFrUniDlciEgressSpExcessBurstSize 1.3.6.1.4.1.562.36.2.1.71.5.6.10.1.3
This attribute specifies the excess burst size (Be) for the egress direction. It is used for Call Admission Control (CAC) function towards the egress link. If the value is set to sameAsSp, the value of this attribute is the same as the excessBurstSize attribute under the ServiceParameters component. VALUES ( 50000001 = sameAsServiceParameters )
OBJECT-TYPE    
  Unsigned32 0..50000000 | 50000001  

mscFrUniDlciEgressSpMeasurementInterval 1.3.6.1.4.1.562.36.2.1.71.5.6.10.1.4
This attribute specifies the time interval over which rates and burst sizes are measured in the egress direction. It is used for bandwidth reservation for Call Admission Control (CAC) towards the egress link. If the value is set to sameAsSp, the value of this attribute is the same as the measurementInterval attribute under the ServiceParameters component. VALUES ( 25501 = sameAsServiceParameters )
OBJECT-TYPE    
  Unsigned32 0..25500 | 25501  

mscFrUniDlciStateTable 1.3.6.1.4.1.562.36.2.1.71.5.10
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciStateEntry

mscFrUniDlciStateEntry 1.3.6.1.4.1.562.36.2.1.71.5.10.1
An entry in the mscFrUniDlciStateTable.
OBJECT-TYPE    
  MscFrUniDlciStateEntry  

mscFrUniDlciAdminState 1.3.6.1.4.1.562.36.2.1.71.5.10.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscFrUniDlciOperationalState 1.3.6.1.4.1.562.36.2.1.71.5.10.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscFrUniDlciUsageState 1.3.6.1.4.1.562.36.2.1.71.5.10.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscFrUniDlciAvailabilityStatus 1.3.6.1.4.1.562.36.2.1.71.5.10.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

mscFrUniDlciProceduralStatus 1.3.6.1.4.1.562.36.2.1.71.5.10.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscFrUniDlciControlStatus 1.3.6.1.4.1.562.36.2.1.71.5.10.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscFrUniDlciAlarmStatus 1.3.6.1.4.1.562.36.2.1.71.5.10.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscFrUniDlciStandbyStatus 1.3.6.1.4.1.562.36.2.1.71.5.10.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
OBJECT-TYPE    
  INTEGER hotStandby(0), coldStandby(1), providingService(2), notSet(15)  

mscFrUniDlciUnknownStatus 1.3.6.1.4.1.562.36.2.1.71.5.10.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
OBJECT-TYPE    
  INTEGER false(0), true(1)  

mscFrUniDlciAbitTable 1.3.6.1.4.1.562.36.2.1.71.5.12
This group contains the A-Bit status information for this Data Link Connection Identifier.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciAbitEntry

mscFrUniDlciAbitEntry 1.3.6.1.4.1.562.36.2.1.71.5.12.1
An entry in the mscFrUniDlciAbitTable.
OBJECT-TYPE    
  MscFrUniDlciAbitEntry  

mscFrUniDlciABitStatusToIf 1.3.6.1.4.1.562.36.2.1.71.5.12.1.1
This attribute is the most recent A-bit status sent to the interface. The A-bit status is part of the LMI protocol, and indicates willingness to accept data from the local interface. inactive - the Frame Relay service discards all data offered from the local interface. active - the Frame Relay service tries to process all data offered from the local interface. notApplicable - the DLCI is switched, so this attribute is ignored.
OBJECT-TYPE    
  INTEGER inactive(0), active(1), notApplicable(2)  

mscFrUniDlciABitReasonToIf 1.3.6.1.4.1.562.36.2.1.71.5.12.1.2
This attribute provides the reason (if any) for an inactive status to be sent to the interface. This reason is notApplicable for an active status.
OBJECT-TYPE    
  INTEGER notApplicable(0), remoteUserSignaled(1), localLmiError(2), remoteLmiError(3), localLinkDown(4), remoteLinkDown(5), pvcSpvcDown(6), userNotAuthorized(8), resourceNotAvailable(9), dlciCollisionAtNni(10)  

mscFrUniDlciABitStatusFromIf 1.3.6.1.4.1.562.36.2.1.71.5.12.1.3
This attribute is the most recent A-Bit status received from the interface. inactive - the Frame Relay service informs the remote DLCI not to send user data to this interface. active - the Frame Relay service informs the remote DLCI that it is okay to send user data to this interface. notApplicable - the DLCI is switched, so this attribute is ignored.
OBJECT-TYPE    
  INTEGER inactive(0), active(1), notApplicable(2)  

mscFrUniDlciABitReasonFromIf 1.3.6.1.4.1.562.36.2.1.71.5.12.1.4
This attribute provides the reason (if any) for an inactive status to be sent to the subnet. This reason is notApplicable for an active status.
OBJECT-TYPE    
  INTEGER notApplicable(0), remoteUserSignaled(1), localLmiError(2), localLinkDown(4), missingFromLmiReport(7)  

mscFrUniDlciLoopbackState 1.3.6.1.4.1.562.36.2.1.71.5.12.1.5
This attribute has the value on when the DLCI is in loopback mode and off otherwise. The loopback command verbs start and stop are used to initiate and terminate the loopback mode for a DLCI. While loopbackState is on, the local LMI will report to the interface the A- bit status as active. Also an active A-bit signal will be reliably propagated across the subnet to the remote DLCI.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscFrUniDlciCalldTable 1.3.6.1.4.1.562.36.2.1.71.5.13
This group of attributes describes the characteristics of the call such as call type and call state.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciCalldEntry

mscFrUniDlciCalldEntry 1.3.6.1.4.1.562.36.2.1.71.5.13.1
An entry in the mscFrUniDlciCalldTable.
OBJECT-TYPE    
  MscFrUniDlciCalldEntry  

mscFrUniDlciCallType 1.3.6.1.4.1.562.36.2.1.71.5.13.1.1
This attribute indicates whether this DLCI is a permancent virtual circuit (PVC), a switched virtual circuit (SVC) or a switched permament virtual circuit (SPVC).
OBJECT-TYPE    
  INTEGER pvc(0), svc(1), spvc(2)  

mscFrUniDlciQstate 1.3.6.1.4.1.562.36.2.1.71.5.13.1.2
This attribute indicates the FRF.4 state of an SVC call. The value of this attribute for a permanent (PVC and P-SPVC) DLCI is always notApplicable. In the description that follows, 'local' refers to the user who has initiated the SETUP request, and 'remote' refers to the user to whom the local user wishes to connect. State description: In the null state, the network has neither received nor sent call setup requests for this DLCI. In the callInitiated state, the network has received a SETUP message from the local user. In the outgoingCallProceeding state, the network has sent a CALL PROCEEDING message to the local user in response to the SETUP message. In the callPresent state, the network has sent a SETUP message to the remote user. In the incomingCallProceeding state, the network has received a CALL PROCEEDING message from the remote user in response to a SETUP message. In the active state, either the network has sent a CONNECT message to the local user, or the network has received a CONNECT from the remote user. In the disconnectRequest state, the network has received a DISCONNECT message from the local user. In the disconnectIndication state, the network has sent a DISCONNECT to the local user. In the releaseRequest state, the network has sent out a RELEASE message to the local user. In the restartRequest state, the network has sent a RESTART request to the local user and is waiting for an acknowledgement. In the restart state, the network has received a request for a restart from the local user and the network has not returned an acknowledgement.
OBJECT-TYPE    
  INTEGER null(0), callInitiated(1), callProceedingSent(3), callPresent(6), callProceedingReceived(9), active(10), disconnectRequest(11), disconnectIndication(12), releaseRequest(19), notApplicable(20), restartRequest(61), restart(62)  

mscFrUniDlciCallref 1.3.6.1.4.1.562.36.2.1.71.5.13.1.3
This attribute indicates the FRF.4 call reference number associated with this DLCI. The value of this attribute for a provisioned (PVC or P-SPVC) DLCI is always 0.
OBJECT-TYPE    
  Unsigned32 0..32767  

mscFrUniDlciSpOpTable 1.3.6.1.4.1.562.36.2.1.71.5.14
This group defines the service and traffic parameters specific to this instance of DLCI. For permanent (PVC and P-SPVC) DLCIs, the values of attributes with the exception of the measurementInterval should be identical to those in the group FrsDataLinkConnectionProv under the FrsUniServiceParametersProv component. For switched (SVC) DLCIs, the values of attributes may be different from the values provisioned under the FrUni Sig component, if signaling negotiations have ocurred to alter the service parameters.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciSpOpEntry

mscFrUniDlciSpOpEntry 1.3.6.1.4.1.562.36.2.1.71.5.14.1
An entry in the mscFrUniDlciSpOpTable.
OBJECT-TYPE    
  MscFrUniDlciSpOpEntry  

mscFrUniDlciMaximumFrameSize 1.3.6.1.4.1.562.36.2.1.71.5.14.1.1
This attribute indicates the maximum number of octets which may be included in the information field. The frame relay header and CRC octets are not included in this definition. This attribute corresponds to the dN1 parameter described in the Vendor Forum Specification.
OBJECT-TYPE    
  Unsigned32 1..8187  

mscFrUniDlciRateEnforcement 1.3.6.1.4.1.562.36.2.1.71.5.14.1.2
This attribute is obsolete. It provided the information which is now represented by the provisionable attribute rateEnforcement under the ServiceParameters component.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscFrUniDlciCommittedInformationRate 1.3.6.1.4.1.562.36.2.1.71.5.14.1.3
This attribute indicates the committed information rate (CIR) in bits per second (bit/s). When rateEnforcement is set to on, cir is the rate at which the network agrees to transfer information under normal conditions. This rate is measured over a measurement interval (t) that is determined internally based on CIR and the committed burst size (Bc). An exception to this occurs when CIR is provisioned to be zero, in which case the measurement interval (t) must be provisioned explicitly. This attribute should be ignored when rateEnforcement is off.
OBJECT-TYPE    
  Unsigned32 0..50000000  

mscFrUniDlciCommittedBurstSize 1.3.6.1.4.1.562.36.2.1.71.5.14.1.4
This attribute indicates the committed burst size (Bc) in bits. bc is the amount of data that a network agrees to transfer under normal conditions over a measurement interval (t). Data marked DE=1 is not accounted for in Bc. This attribute should be ignored when rateEnforcement is off.
OBJECT-TYPE    
  Unsigned32 0..50000000  

mscFrUniDlciExcessBurstSize 1.3.6.1.4.1.562.36.2.1.71.5.14.1.5
This attribute indicates the excess burst size (Be) in bits. Be is the amount of uncommitted data that the network will attempt to deliver over measurement interval T. Data marked DE=1 by the user or by the network is accounted for here. This attribute should be ignored when rateEnforcement is off.
OBJECT-TYPE    
  Unsigned32 0..50000000  

mscFrUniDlciMeasurementInterval 1.3.6.1.4.1.562.36.2.1.71.5.14.1.6
This attribute indicates the time interval (in milliseconds) over which rates and burst sizes are measured. This attribute should be ignored when rateEnforcement is off.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciRateAdaptation 1.3.6.1.4.1.562.36.2.1.71.5.14.1.7
This attribute is obsolete. It provided the information which is now represented by the provisionable attribute rateAdaptation under the ServiceParameters component.
OBJECT-TYPE    
  INTEGER off(0), on(1), eirOnly(2)  

mscFrUniDlciAccounting 1.3.6.1.4.1.562.36.2.1.71.5.14.1.8
This attribute indicates whether accounting data collection and record generation is turned on at this DLCI. For accounting data collection and record generation to be turned on, the accountingOn bit and at least one of the accountCollection bits in the DataNetworkAddress component must be set to on.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscFrUniDlciEmissionPriorityToIf 1.3.6.1.4.1.562.36.2.1.71.5.14.1.9
This attribute indicates the emission priority of frames sent to the interface. A larger value denotes a higher priority.
OBJECT-TYPE    
  INTEGER 0 | 1 | 2 | 3  

mscFrUniDlciTransferPriToNwk 1.3.6.1.4.1.562.36.2.1.71.5.14.1.10
This attribute indicates the priority at which data is transferred to the network. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 indices from 0 to 15. Each transfer priority n, where n specifies the transfer priority index, contains a default setting for routing class of service (multimedia, delay, or throughput) and frame relay egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned in the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required.
OBJECT-TYPE    
  Unsigned32 0..15  

mscFrUniDlciTransferPriFromNwk 1.3.6.1.4.1.562.36.2.1.71.5.14.1.11
This attribute indicates the priority at which data is transferred from the network. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 indices from 0 to 15. Each transfer priority n, where n specifies the transfer priority index, contains a default setting for routing class of service (multimedia, delay, or throughput) and frame relay egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned in the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required.
OBJECT-TYPE    
  Unsigned32 0..15  

mscFrUniDlciStatsTable 1.3.6.1.4.1.562.36.2.1.71.5.15
This group contains the operational statistics for the Frame Relay Data Link Connection Identifier.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciStatsEntry

mscFrUniDlciStatsEntry 1.3.6.1.4.1.562.36.2.1.71.5.15.1
An entry in the mscFrUniDlciStatsTable.
OBJECT-TYPE    
  MscFrUniDlciStatsEntry  

mscFrUniDlciFrmToIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.1
This attribute counts the frames sent out the interface. When the maximum count is reached the count wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciFecnFrmToIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.2
This attribute counts the frames sent to the interface with the Forward Explicit Congestion Notification (FECN) bit set. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciBecnFrmToIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.3
This attribute counts the frames sent to the interface with the Backward Explicit Congestion Notification (BECN) bit set. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciBciToSubnet 1.3.6.1.4.1.562.36.2.1.71.5.15.1.4
This attribute counts the frames sent into the local network with the Backward Congestion Indication (BCI) bit set. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDeFrmToIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.5
This attribute counts the frames sent to the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDiscCongestedToIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.6
This attribute counts the number of frame discards at the Frame Relay service due to local congestion in the direction toward the interface. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDiscDeCongestedToIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.7
This attribute counts the number of discarded frames, with the Discard Eligibility (DE) bit set, at the Frame Relay service, due to local congestion in the direction toward the interface. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciFrmFromIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.8
This attribute counts the frames received from the interface. It includes the frames that are discarded due to error or excess. When the maximum count is reached the count wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciFecnFrmFromIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.9
This attribute counts the frames received from the interface with the Forward Explicit Congestion Notification (FECN) bit set. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciBecnFrmFromIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.10
This attribute counts the frames received from the interface with the Backward Explicit Congestion Notification (BECN) bit set. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciFciFromSubnet 1.3.6.1.4.1.562.36.2.1.71.5.15.1.11
This attribute counts the frames received from the network with the Forward Congestion Indication (FCI) bit set. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciBciFromSubnet 1.3.6.1.4.1.562.36.2.1.71.5.15.1.12
This attribute counts the frames received from the network with the Backward Congestion Indication (BCI) bit set. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDeFrmFromIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.13
This attribute counts the frames received from the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciExcessFrmFromIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.14
This attribute counts the frames received from the interface with the Discard Eligibility (DE) bit clear, but subsequently set by the network due to rate enforcement. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDiscExcessFromIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.15
This attribute counts the frames which were discarded due to rate enforcement. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDiscFrameAbit 1.3.6.1.4.1.562.36.2.1.71.5.15.1.16
This attribute counts the number of frame discards at the Frame Relay Service, due to an inactive PVC status, in the direction toward the local network. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDiscCongestedFromIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.17
This attribute counts the number of frame discards at the Frame Relay service due to local congestion in the direction toward the network. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDiscDeCongestedFromIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.18
This attribute counts the number of discarded frames, with the Discard Eligibility (DE) bit set, at the Frame Relay service, due to local congestion, in the direction toward the local network. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciErrorShortFrmFromIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.19
This attribute counts the frames received with 0 octets in the information field. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciErrorLongFrmFromIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.20
This attribute counts the frames received with number of octets in the information field greater than the subscribed maximum. When the count reaches maximum it wraps to zero. Frames whose lengths are greater than the hardware receive buffer are ignored by the hardware and are therefore not included in this count.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciBecnFrmSetByService 1.3.6.1.4.1.562.36.2.1.71.5.15.1.21
This attribute counts the number of frames with BECN set by the Frame Relay service. It is incremented whenever the Frame Relay service sets BECN on a frame upon detecting local congestion. This count is incremented regardless of whether the frame already bears a set BECN bit since its use is to determine the place of congestion. When the count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciBytesToIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.22
This attribute counts the bytes sent out the interface. When the maximum count is reached the count wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDeBytesToIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.23
This attribute counts the bytes sent to the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDiscCongestedToIfBytes 1.3.6.1.4.1.562.36.2.1.71.5.15.1.24
This attribute counts the number of byte discards at the Frame Relay service due to local congestion in the direction toward the link. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDiscDeCongestedToIfBytes 1.3.6.1.4.1.562.36.2.1.71.5.15.1.25
This attribute counts the number of discard eligible (DE=1) byte discards at the Frame Relay service due to local congestion in the direction toward the link. When the maximum count is reached the count wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciBytesFromIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.26
This attribute counts the bytes received from the interface. Bytes that are discarded due to error or excess are not counted. When the maximum count is reached the count wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDeBytesFromIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.27
This attribute counts the bytes received from the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciExcessBytesFromIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.28
This attribute counts the bytes received from the interface with the Discard Eligibility (DE) bit clear, but subsequently set by the network due to rate enforcement. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDiscExcessFromIfBytes 1.3.6.1.4.1.562.36.2.1.71.5.15.1.29
This attribute counts the bytes which were discarded due to rate enforcement. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDiscByteAbit 1.3.6.1.4.1.562.36.2.1.71.5.15.1.30
This attribute counts the bytes which were discarded due to aBit turned off.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDiscCongestedFromIfBytes 1.3.6.1.4.1.562.36.2.1.71.5.15.1.31
This attribute counts the number of byte discards at the Frame Relay service due to local congestion in the direction toward the network. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDiscDeCongestedFromIfBytes 1.3.6.1.4.1.562.36.2.1.71.5.15.1.32
This attribute counts the number of discard eligible (DE=1) byte discards at the Frame Relay service due to local congestion in the direction toward the network. When the maximum count is reached the count wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciErrorShortBytesFromIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.33
This attribute counts the bytes received with 0 octets in the information field. When the count reaches maximum it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciErrorLongBytesFromIf 1.3.6.1.4.1.562.36.2.1.71.5.15.1.34
This attribute counts the bytes received with number of octets in the information field greater than the subscribed maximum. When the count reaches maximum it wraps to zero. Bytes whose lengths are greater than the hardware receive buffer are ignored by the hardware and are therefore not included in this count.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciRateAdaptReduct 1.3.6.1.4.1.562.36.2.1.71.5.15.1.35
This attribute counts the number of rate reductions due to rate adaptation. Rate adaptation causes the allowed rate to be reduced in steps. After each reduction, a period of time is awaited before further action is taken. At the end of this period, the allowed rate is further reduced if congestion is still prevalent. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciRateAdaptReductPeriod 1.3.6.1.4.1.562.36.2.1.71.5.15.1.36
This attribute provides a cumulative count of the amount of time that rate adaptation procedures have been in effect. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciTransferPriorityToNetwork 1.3.6.1.4.1.562.36.2.1.71.5.15.1.37
This attribute is obsolete. It is replaced by attribute transferPriorityToNetwork under group FrsNniDataLinkConnectionIdentifierServiceParametersOp.
OBJECT-TYPE    
  INTEGER 0..15  

mscFrUniDlciTransferPriorityFromNetwork 1.3.6.1.4.1.562.36.2.1.71.5.15.1.38
This attribute is obsolete. It is replaced by attribute transferPriorityFromNetwork under group FrsNniDataLinkConnectionIdentifierServiceParametersOp.
OBJECT-TYPE    
  INTEGER 0..15  

mscFrUniDlciCirPresent 1.3.6.1.4.1.562.36.2.1.71.5.15.1.39
This attribute provides the actual Committed Information Rate (CIR) enforced for this DLCI. This number is in units of 800 bits/ sec, since that is the internal resolution of Passport rate enforcement. If rateEnforcement is off, then this number does not have meaning. Normally, this attribute matches the provisioned CIR for the DLCI. But when Rate Adaptation is active, then this number will vary to represent the actual Allowed CIR at the moment that this attribute is collected.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciEirPresent 1.3.6.1.4.1.562.36.2.1.71.5.15.1.40
This attribute provides the actual Excess Information Rate (EIR) enforced for this DLCI. This number is in units of 800 bits/sec, since that is the internal resolution of Passport rate enforcement. If rateEnforcement is off, then this number does not have meaning. Normally, this attribute matches the provisioned EIR for the DLCI. But when Rate Adaptation is active, then this number will vary to represent the actual Allowed EIR at the moment that this attribute is collected.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciIntTable 1.3.6.1.4.1.562.36.2.1.71.5.16
This group contains the operational statistics for the Frame Relay Data Link Connection Identifier interval data (accounting data).
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniDlciIntEntry

mscFrUniDlciIntEntry 1.3.6.1.4.1.562.36.2.1.71.5.16.1
An entry in the mscFrUniDlciIntTable.
OBJECT-TYPE    
  MscFrUniDlciIntEntry  

mscFrUniDlciStartTime 1.3.6.1.4.1.562.36.2.1.71.5.16.1.1
This attribute indicates the start time of this interval period. If Vc spans 12 hour time or time of day change startTime reflects new time as recorded at 12 hour periods or time of day changes. A new interval period is started each time an accounting record is generated.
OBJECT-TYPE    
  EnterpriseDateAndTime SIZE(0 | 19)  

mscFrUniDlciTotalIngressBytes 1.3.6.1.4.1.562.36.2.1.71.5.16.1.2
This attribute counts the total bytes received from the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
OBJECT-TYPE    
  Unsigned64 SIZE(8)  

mscFrUniDlciTotalEgressBytes 1.3.6.1.4.1.562.36.2.1.71.5.16.1.3
This attribute counts the total bytes sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
OBJECT-TYPE    
  Unsigned64 SIZE(8)  

mscFrUniDlciEirIngressBytes 1.3.6.1.4.1.562.36.2.1.71.5.16.1.4
This attribute counts the total bytes with the Discard Eligibility (DE) bit set sent to the subnet since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
OBJECT-TYPE    
  Unsigned64 SIZE(8)  

mscFrUniDlciEirEgressBytes 1.3.6.1.4.1.562.36.2.1.71.5.16.1.5
This attribute counts the total bytes with the Discard Eligibility (DE) bit set sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
OBJECT-TYPE    
  Unsigned64 SIZE(8)  

mscFrUniDlciDiscardedBytes 1.3.6.1.4.1.562.36.2.1.71.5.16.1.6
This attribute counts the total bytes in invalid frames received from the interface and discarded at the DLCI since the start of the interval period. This count is a sum of octets in frames discarded due to the number of octets in the information field greater than the subscribed maximum or equal to 0, due to aBit turned off, or due to rate enforcement. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
OBJECT-TYPE    
  Unsigned64 SIZE(8)  

mscFrUniDlciTotalIngressSegFrm 1.3.6.1.4.1.562.36.2.1.71.5.16.1.7
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the total number of segments in frames received from the interface since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the total number of frames received from the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciTotalEgressSegFrm 1.3.6.1.4.1.562.36.2.1.71.5.16.1.8
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the total number of segments in frames sent to the interface since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the total number of frames sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciEirIngressSegFrm 1.3.6.1.4.1.562.36.2.1.71.5.16.1.9
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the number of segments in frames with the Discard Eligibility (DE) bit set sent to the subnet since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the number of frames with the Discard Eligibility (DE) bit set sent to the subnet since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciEirEgressSegFrm 1.3.6.1.4.1.562.36.2.1.71.5.16.1.10
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the number of segments in frames with the Discard Eligibility (DE) bit set sent to the interface since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the number of frames with the Discard Eligibility (DE) bit set sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciDiscardedSegFrm 1.3.6.1.4.1.562.36.2.1.71.5.16.1.11
If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the number of segments in invalid frames received from the interface and discarded at the DLCI. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the number of invalid frames received from the interface and discarded at the DLCI. Segments of frames are counted since the start of the interval period. The count is reset to zero when an accounting record is generated. The count is a sum of segments in frames or frames discarded due to the number of octets in the information field greater than the subscribed maximum or equal to 0, due to aBit turned off, or due to rate enforcement.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciCirPresentObs 1.3.6.1.4.1.562.36.2.1.71.5.16.1.12
This attribute has moved to the statistics subgroup. See cirPresent..
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciEirPresentObs 1.3.6.1.4.1.562.36.2.1.71.5.16.1.13
This attribute has moved to the statistics subgroup. See eirPresent.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciRateEnforcementPresent 1.3.6.1.4.1.562.36.2.1.71.5.16.1.14
This attribute is obsolete. See the provisionable rateEnforcement attribute.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscFrUniDlciRateAdaptationPresent 1.3.6.1.4.1.562.36.2.1.71.5.16.1.15
This attribute is obsolete. See the provisionable rateAdaptation attribute.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscFrUniDlciLocalRateAdaptOccurred 1.3.6.1.4.1.562.36.2.1.71.5.16.1.16
This attribute indicates whether rate adaptation has occurred on this user Data Link Connection on this Frame Relay interface. The value is reset to no when an accounting record is generated.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mscFrUniDlciCallReferenceNumber 1.3.6.1.4.1.562.36.2.1.71.5.16.1.17
This attribute is obsoleted and replaced by callRefNumber.
OBJECT-TYPE    
  Hex 0..16777215  

mscFrUniDlciElapsedDifference 1.3.6.1.4.1.562.36.2.1.71.5.16.1.18
This attribute indicates the elapsed time representing the period of this interval data. It is elapsed time in 0.1 second increments since the call started.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniDlciCallRefNumber 1.3.6.1.4.1.562.36.2.1.71.5.16.1.20
This attribute indicates the call reference number which is a unique number generated by the switch.The same Call Reference Number is stored in the interval data (accounting record) at both ends of the call. It can be used as one of the attributes in matching duplicate records generated at each end of the call.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniSig 1.3.6.1.4.1.562.36.2.1.71.6
OBJECT IDENTIFIER    

mscFrUniSigRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.6.1
This entry controls the addition and deletion of mscFrUniSig components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniSigRowStatusEntry

mscFrUniSigRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.6.1.1
A single entry in the table represents a single mscFrUniSig component.
OBJECT-TYPE    
  MscFrUniSigRowStatusEntry  

mscFrUniSigRowStatus 1.3.6.1.4.1.562.36.2.1.71.6.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniSig components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniSigComponentName 1.3.6.1.4.1.562.36.2.1.71.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniSigStorageType 1.3.6.1.4.1.562.36.2.1.71.6.1.1.4
This variable represents the storage type value for the mscFrUniSig tables.
OBJECT-TYPE    
  StorageType  

mscFrUniSigIndex 1.3.6.1.4.1.562.36.2.1.71.6.1.1.10
This variable represents the index for the mscFrUniSig tables.
OBJECT-TYPE    
  NonReplicated  

mscFrUniSigRangeTable 1.3.6.1.4.1.562.36.2.1.71.6.11
This group contains the provisionable attribute to define the range of DLCIs for PVCs and SVCs. The purpose of this range is to prevent DLCI collisions between the provisioned PVCs and the dynamic SVCs.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniSigRangeEntry

mscFrUniSigRangeEntry 1.3.6.1.4.1.562.36.2.1.71.6.11.1
An entry in the mscFrUniSigRangeTable.
OBJECT-TYPE    
  MscFrUniSigRangeEntry  

mscFrUniSigHighestPvcDlci 1.3.6.1.4.1.562.36.2.1.71.6.11.1.1
This attribute specifies the highest DLCI value that can be provisioned for a PVC. It partitions the DLCI space into PVC and SVC. PVC DLCI numbers higher than this value are rejected. The value 0 is used to indicate that no PVCs are allowed on the interface. The value 1007 indicates that no SVCs are allowed on the interface.
OBJECT-TYPE    
  Unsigned32 0 | 16..1007  

mscFrUniSigHighestPermanentDlci 1.3.6.1.4.1.562.36.2.1.71.6.11.1.4
This attribute specifies the highest DLCI value that can be provisioned for a permanent connection. It partitions the DLCI space into permanent and switched connections. Permanent DLCI numbers higher than this value cannot be provisioned. The value 0 is used to indicate that no permanent connections are allowed on this interface. The value 1007 indicates that no switched connections are allowed on this interface.
OBJECT-TYPE    
  Unsigned32 0 | 16..1007  

mscFrUniSigHighestFriPvcDlci 1.3.6.1.4.1.562.36.2.1.71.6.11.1.5
This attribute specifies the highest DLCI value that can be provisioned for a permanent connection. It partitions the DLCI space into permanent and switched connections. Permanent DLCI numbers higher than this value cannot be provisioned. The value 0 is used to indicate that no permanent connections are allowed on this interface. The value 1007 indicates that no switched connections are allowed on this interface.
OBJECT-TYPE    
  Unsigned32 0 | 16..1007  

mscFrUniSigServParmsTable 1.3.6.1.4.1.562.36.2.1.71.6.12
This group contains the provisionable FRF.4 service parameters.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniSigServParmsEntry

mscFrUniSigServParmsEntry 1.3.6.1.4.1.562.36.2.1.71.6.12.1
An entry in the mscFrUniSigServParmsTable.
OBJECT-TYPE    
  MscFrUniSigServParmsEntry  

mscFrUniSigMaximumAggregateSvcCir 1.3.6.1.4.1.562.36.2.1.71.6.12.1.1
This attribute specifies the maximum aggregate user to network direction CIR allowed for SVCs on the interface. It is provisioned as a percentage of the access link speed. This attribute is used to limit the amount of guaranteed SVC throughput allowed into the network at this interface. This attribute is obsoleted, during the migration, the value of this attribute will be transfered to maximumAggregateSvcCirNormalQ or maximumAggregateSvcCirHighQ depending on the value of the attribute outDefaultPathSensitivity under DNA component.
OBJECT-TYPE    
  Unsigned32 0..10000  

mscFrUniSigMaximumAggregateSvcEir 1.3.6.1.4.1.562.36.2.1.71.6.12.1.2
This attribute specifies the maximum aggregate user to network direction EIR allowed for SVCs on the interface. It is provisioned as a percentage of the access link speed. This attribute is ignored if unlimitedAggregateEir, another attribute under the same group, is set to yes. This attribute is used to limit the amount of excess SVC throughput allowed into the network at this interface. This attribute is obsoleted, during the migration, the value of this attribute will be transfered to maximumAggregateSvcEirNormalQ or maximumAggregateSvcEirHighQ depending on the value of the attribute outDefaultPathSensitivity under DNA component.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniSigMaximumFrameSize 1.3.6.1.4.1.562.36.2.1.71.6.12.1.3
This attribute specifies the maximum number of octets that may be included in the information field of the user DLCI of any switched connections using this interface. Its value must not be smaller than the value of defaultMaximumFrameSize.
OBJECT-TYPE    
  Unsigned32 1..8187  

mscFrUniSigDefaultMaximumFrameSize 1.3.6.1.4.1.562.36.2.1.71.6.12.1.4
This attribute specifies the default maximum number of octets that may be included in the information field of the user DLCI assigned for any switched connections using this interface. This value is used during call parameter negotiation for switched calls on this interface when the maximum frame size is not specified in the user's SETUP message. The value of this attribute must not exceed the value of the maximumFrameSize attribute.
OBJECT-TYPE    
  Unsigned32 1..8187  

mscFrUniSigDefaultCommittedInformationRate 1.3.6.1.4.1.562.36.2.1.71.6.12.1.5
This attribute specifies the default user to network direction CIR. This value is used during call parameter negotiation for switched calls on this interface when the CIR is not specified in the user's SETUP message.
OBJECT-TYPE    
  Unsigned32 0..52000000  

mscFrUniSigDefaultCommittedBurstSize 1.3.6.1.4.1.562.36.2.1.71.6.12.1.6
This attribute specifies the default user to network direction Bc. This value is used during call parameter negotiation for switched calls on this interface when the Bc is not specified in the user's SETUP message.
OBJECT-TYPE    
  Unsigned32 0..52000000  

mscFrUniSigDefaultExcessBurstSize 1.3.6.1.4.1.562.36.2.1.71.6.12.1.7
This attribute specifies the default user to network direction Be. This value is used during call parameter negotiation for switched calls on this interface when the Be is not specified in the user's SETUP message.
OBJECT-TYPE    
  Unsigned32 0..52000000  

mscFrUniSigUnlimitedAggregateEir 1.3.6.1.4.1.562.36.2.1.71.6.12.1.8
This attribute specifies whether the network will enforce aggregate EIR during SVC call establishment. The network keeps track of the sum of user to network EIRs for all the SVC DLCIs at this interface. If this attribute is set to no, then the requested EIR for each new SVC call will be adjusted if the resulting aggregate EIR exceeds the value contained in one of the following attributes (depending on the requested Transfer Priority): maximumAggregateSvcEirNormalQ, maximumAggregateSvcEirHighQ or maximumAggregateSvcEirInterruptQ. This may lead to a rejection of the call setup. If this value is set to yes, then no checks will take place.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mscFrUniSigRateEnforcement 1.3.6.1.4.1.562.36.2.1.71.6.12.1.9
This attribute specifies whether rate enforcement is in effect for SVCs on this interface.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscFrUniSigRateAdaptation 1.3.6.1.4.1.562.36.2.1.71.6.12.1.10
This attribute specifies whether closed-loop rate adaptation is in effect for SVCs on this interface. Rate adaptation is a feature that, in periods of congestion, adapts the rate at which the user is allowed to send data into the network to that which the network is able to handle at that time. This proactive measure of handling congestion optimizes network resources by causing the ingress to discard frames that would otherwise be discarded in the network. If this attribute is set to on, then, at the onset of congestion, the excess information rate (EIR) is reduced to a very low rate. If congestion persists, then the allowed CIR is reduced geometrically by 25% of the current value at that time. The minimum to which CIR can be reduced is 1/16th (6.25%) of the provisioned value. As congestion alleviates, CIR is increased linearly by 6.25% of the provisioned value specified in committedInformationRate. If set to eirOnly, then rate adaptation will only apply to the excess information rate (EIR). At the onset of congestion, the allowed EIR is reduced by 25% of its provisioned value. If congestion persists, EIR is reduced geometrically by 25% of the current value at that time. As congestion alleviates, EIR is gradually increased linearly by 6.25% of the provisioned EIR. If set to cirProportionate, then rate adaptation will also only apply to the excess information rate (EIR). At the onset of congestion the initial allowed EIR is set to a multiple of the provisioned CIR. If congestion persists, the allowed EIR is reduced geometrically by 25% of the current value at that time. As congestion alleviates, EIR is gradually increased linearly by 6.25% of the provisioned EIR. Note that the allowed EIR may be set higher than the provisioned EIR, since it is calculated initially using another parameter, the provisioned CIR. If the allowed EIR at the moment is higher than the provisioned EIR, then the provisioned EIR is used instead. This attribute can only be set to on or eirOnly if rateEnforcement is set to on.
OBJECT-TYPE    
  INTEGER off(0), on(1), eirOnly(2), cirProportionate(3)  

mscFrUniSigMaximumAggregateSvcCirNormalQ 1.3.6.1.4.1.562.36.2.1.71.6.12.1.11
This attribute specifies the maximum aggregate user to network direction CIR allowed for SVCs on the interface. It is provisioned as a percentage of the access link speed. This attribute is used to limit, at this interface, the amount of guaranteed SVC throughput allowed into the network through the normal priority queue.
OBJECT-TYPE    
  Unsigned32 0..10000  

mscFrUniSigMaximumAggregateSvcCirHighQ 1.3.6.1.4.1.562.36.2.1.71.6.12.1.12
This attribute specifies the maximum aggregate user to network direction CIR allowed for SVCs on the interface. It is provisioned as a percentage of the link access speed. This attribute is used to limit, at this interface, the amount of guaranteed SVC throughput allowed into the network through the high priority queue.
OBJECT-TYPE    
  Unsigned32 0..10000  

mscFrUniSigMaximumAggregateSvcCirInterruptQ 1.3.6.1.4.1.562.36.2.1.71.6.12.1.13
This attribute specifies the maximum aggregate user to network direction CIR allowed for SVCs on the interface. It is provisioned as a percentage of the link access speed. This attribute is used to limit, at this interface, the amount of guaranteed SVC throughput allowed into the network through the interrupting queue.
OBJECT-TYPE    
  Unsigned32 0..10000  

mscFrUniSigMaximumAggregateSvcEirNormalQ 1.3.6.1.4.1.562.36.2.1.71.6.12.1.14
This attribute specifies the maximum aggregate user to network direction EIR allowed for SVCs on the interface. It is provisioned as a percentage of the access link speed. This attribute is ignored if unlimitedAggregateEir, another attribute under the same group, is set to yes. This attribute is used to limit, at this interface, the amount of excess SVC throughput allowed into the network through the normal priority queue.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniSigMaximumAggregateSvcEirHighQ 1.3.6.1.4.1.562.36.2.1.71.6.12.1.15
This attribute specifies the maximum aggregate user to network direction EIR allowed for SVCs on the interface. It is provisioned as a percentage of the access link speed. This attribute is ignored if unlimitedAggregateEir, another attribute under the same group, is set to yes. This attribute is used to limit, at this interface, the amount of excess SVC throughput allowed into the network through the high priority queue.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniSigMaximumAggregateSvcEirInterruptQ 1.3.6.1.4.1.562.36.2.1.71.6.12.1.16
This attribute specifies the maximum aggregate user to network direction EIR allowed for SVCs on the interface. It is provisioned as a percentage of the access link speed. This attribute is ignored if unlimitedAggregateEir, another attribute under the same group, is set to yes. This attribute is used to limit, at this interface, the amount of excess SVC throughput allowed into the network through the interrupting queue.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniSigX213IeHandling 1.3.6.1.4.1.562.36.2.1.71.6.12.1.17
The x213IeHandling attribute specifies how Frame Relay handles the X.213 Priority IE when it is in the FRF.4 setup message. When the attribute is set to notSupported, the X.213 Priority IE will not be recognized in the setup message. A FRF.4 status message will be sent to the calling DTE, with the indication that an unrecognized IE was encountered. The call setup then proceeds as normal, and the X.213 Priority IE does not appear in the setup message at the called end. When the attribute is set to proprietary, and the X.213 Priority IE is present in the FRF.4 setup message, it will be recognized. If there is no Frame Transfer Priority IE in the setup message, the first data byte of the X.213 Priority IE is used to select the transfer and discard priority values for the connection and the X.213 Priority IE is signaled to the called end in the setup message. If the Frame Transfer Priority IE is present in the FRF.4 setup message, its value is used to select the transfer priority, the discard priority is taken from the FRUNI Dna component, and the X.213 Priority IE is ignored. Refer to the related Application Note for further details before setting the attribute value to proprietary.
OBJECT-TYPE    
  INTEGER notSupported(0), proprietary(1)  

mscFrUniSigRaSensitivity 1.3.6.1.4.1.562.36.2.1.71.6.12.1.18
This attribute specifies the sensitivity of the rate adaptation system for all switched connections on this interface. A higher number indicates a higher sensitivity and therefore a quicker reaction time to network conditions. A quicker reaction time allows the network to discard frames at the access and protect network resources, but can lead to false alarms and a greater fluctuation of the allowed rate. A higher setting therefore tends to favor the protection of the network over the allowed throughput of the user. A lower number indicates a lower sensitivity and therefore a slower reaction to network conditions. A slower reaction time results in a greater amount of user traffic allowed into the network, but can lead to a waste of network bandwidth since the traffic may be discarded at the congested resource. A lower setting therefore tends to favour the allowed throughput of the user over the protection of the network. This attribute is applicable for adapting EIR when rateAdaptation is eirOnly or cirProportionate, or CIR when rateAdaptation is on. This attribute is ignored if rateAdaptation is off.
OBJECT-TYPE    
  Unsigned32 1..20  

mscFrUniSigUpdateBCI 1.3.6.1.4.1.562.36.2.1.71.6.12.1.19
This attribute specifies whether internal Backward Congestion Indication (BCI) bits will report congestion external to the Passport network, as communicated through incoming BECN bits. If updateBCI is set to on, then BCI bits for incoming frames will be set if the BECN on the frame is set. If updateBCI is set to off, then incoming BECN bits has no effect. Setting updateBCI on for a DLCI means that the remote end of the DLCI, which is specified by the remoteDna and remoteDlci attributes of the Dc component of the Dlci, may perform Rate Adaptation using the flow of incoming BECN bits, in addition to internal Passport congestion management systems. If the rateAdaptation attribute of the remote DLCI is provisioned as eirOnly, cirProportionate, or on, then congestion from another network connected to a Passport network may trigger dynamic congestion management. If there is no rate adaptation at the other end, then the setting of updateBCI attribute here will have no effect.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscFrUniSigDefaultLocCheck 1.3.6.1.4.1.562.36.2.1.71.6.12.1.20
This attribute specifies whether Passport needs to check the location of Cause IE in a Release or a Disc message issued by local DTE. If this bit is set to on, then Passport will check the location of Cause IE issued by the local DTE and overwrite it by 'user'. If it is set to off, then Passport will not check the location in Cause IE.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscFrUniSigSysParmsTable 1.3.6.1.4.1.562.36.2.1.71.6.13
This group contains the provisionable FRF.4 system parameters.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniSigSysParmsEntry

mscFrUniSigSysParmsEntry 1.3.6.1.4.1.562.36.2.1.71.6.13.1
An entry in the mscFrUniSigSysParmsTable.
OBJECT-TYPE    
  MscFrUniSigSysParmsEntry  

mscFrUniSigCallSetupTimer 1.3.6.1.4.1.562.36.2.1.71.6.13.1.1
This attribute specifies the time the network waits for a response to the SETUP message sent to the called user. Upon timer expiry, the SETUP message is retransmitted. The second expiry of this timer causes the call to be cleared.
OBJECT-TYPE    
  Unsigned32 1..255  

mscFrUniSigDisconnectTimer 1.3.6.1.4.1.562.36.2.1.71.6.13.1.2
This attribute specifies the time the network waits for a response to the DISCONNECT message sent to the user. Upon timer expiry, the RELEASE message is sent.
OBJECT-TYPE    
  Unsigned32 1..255  

mscFrUniSigReleaseTimer 1.3.6.1.4.1.562.36.2.1.71.6.13.1.3
This attribute specifies the time the network waits for a response to the RELEASE message sent to the user. Upon timer expiry, the RELEASE message is retransmitted. The second expiry of the timer causes the call to be released.
OBJECT-TYPE    
  Unsigned32 1..255  

mscFrUniSigCallProceedingTimer 1.3.6.1.4.1.562.36.2.1.71.6.13.1.4
This attribute specifies the time the network waits for the CONNECT message from the called user after the network has received the optional CALL PROCEEDING message from the called user. Upon timer expiry, the call is cleared.
OBJECT-TYPE    
  Unsigned32 1..255  

mscFrUniSigNetworkType 1.3.6.1.4.1.562.36.2.1.71.6.13.1.5
This attribute specifies whether this Frame Relay service is running on a public or a private network. This value is used solely in populating applicable information elements within those FRF.4 messages that require a public or private network indication.
OBJECT-TYPE    
  INTEGER private(1), public(2)  

mscFrUniSigRestartReqTimer 1.3.6.1.4.1.562.36.2.1.71.6.13.1.6
This attribute specifies the time the network waits for the RESTART ACKNOWLEDGE message from the adjacent network after sending a first RESTART message. Upon timer expiry, another RESTART message is sent. After the second expiry, the interface is treated as idle. If the restartReqTimer attribute is set to the default value, then the interface is treated as idle when it receives an indication that the link is up and does not send a RESTART message.
OBJECT-TYPE    
  Unsigned32 0..255  

mscFrUniSigRestartRcvTimer 1.3.6.1.4.1.562.36.2.1.71.6.13.1.7
This attribute specifies the time the local network waits for the processing of a RESTART message received by the interface. Upon expiry of this timer, an alarm will be displayed to report the problem. The timer value must be less than the restartReqTimer provisioned value at the adjacent node.
OBJECT-TYPE    
  Unsigned32 1..255  

mscFrUniSigStatusEnqTimer 1.3.6.1.4.1.562.36.2.1.71.6.13.1.8
This attribute specifies the time the network waits for the requested STATUS message from the adjacent network. Upon expiry of this timer, another STATUS ENQUIRY message will be sent.
OBJECT-TYPE    
  Unsigned32 1..255  

mscFrUniSigLapfSysTable 1.3.6.1.4.1.562.36.2.1.71.6.14
This group contains the provisionable attributes for the SVC data link layer. The data link layer is governed primarily through ITU specification Q.922, and operates over DLCI 0..
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniSigLapfSysEntry

mscFrUniSigLapfSysEntry 1.3.6.1.4.1.562.36.2.1.71.6.14.1
An entry in the mscFrUniSigLapfSysTable.
OBJECT-TYPE    
  MscFrUniSigLapfSysEntry  

mscFrUniSigWindowSize 1.3.6.1.4.1.562.36.2.1.71.6.14.1.2
This attribute specifies the window size. This is the maximum number of unacknowledged sequenced frames that may be outstanding from or to this interface at any one time.
OBJECT-TYPE    
  Unsigned32 1..127  

mscFrUniSigRetransmitLimit 1.3.6.1.4.1.562.36.2.1.71.6.14.1.3
This attribute specifies the number of times a frame can be retransmitted by the SVC data link layer before appropriate recovery action is taken.
OBJECT-TYPE    
  Unsigned32 0..20  

mscFrUniSigAckTimer 1.3.6.1.4.1.562.36.2.1.71.6.14.1.4
This attribute specifies how long the layer 2 protocol waits for an acknowledgment to a sent frame. The value set for ackTimer must be less than the value set for idleProbeTimer.
OBJECT-TYPE    
  Unsigned32 1000..10000  

mscFrUniSigAckDelayTimer 1.3.6.1.4.1.562.36.2.1.71.6.14.1.5
This attribute specifies how long the network waits before sending an acknowledgment for a received in-sequence I-frame. A value of 0 means that every frame is acknowledged and there will be no delay in acknowledgment. A non-zero value means that one acknowledgement is sent for a number of frames.
OBJECT-TYPE    
  Unsigned32 0..10000  

mscFrUniSigIdleProbeTimer 1.3.6.1.4.1.562.36.2.1.71.6.14.1.6
This attribute specifies how long the link is permitted to remain idle (that is, no frames are exchanged on the data link). Upon expiry of this timer, the network side's link layer polls its peer for status. The value set for idleProbeTimer must be greater than the value set for ackTimer.
OBJECT-TYPE    
  Unsigned32 1000..65535000  

mscFrUniSigStateTable 1.3.6.1.4.1.562.36.2.1.71.6.15
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniSigStateEntry

mscFrUniSigStateEntry 1.3.6.1.4.1.562.36.2.1.71.6.15.1
An entry in the mscFrUniSigStateTable.
OBJECT-TYPE    
  MscFrUniSigStateEntry  

mscFrUniSigAdminState 1.3.6.1.4.1.562.36.2.1.71.6.15.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscFrUniSigOperationalState 1.3.6.1.4.1.562.36.2.1.71.6.15.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscFrUniSigUsageState 1.3.6.1.4.1.562.36.2.1.71.6.15.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscFrUniSigStatsTable 1.3.6.1.4.1.562.36.2.1.71.6.16
This group contains the statistics related to the SVC signaling layer at the interface level.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniSigStatsEntry

mscFrUniSigStatsEntry 1.3.6.1.4.1.562.36.2.1.71.6.16.1
An entry in the mscFrUniSigStatsTable.
OBJECT-TYPE    
  MscFrUniSigStatsEntry  

mscFrUniSigCurrentNumberOfSvcCalls 1.3.6.1.4.1.562.36.2.1.71.6.16.1.1
This attribute indicates the number of Frame Relay SVCs currently existing on this interface.
OBJECT-TYPE    
  Gauge32 0..992  

mscFrUniSigInCalls 1.3.6.1.4.1.562.36.2.1.71.6.16.1.4
This attribute indicates the current number of incoming SVCs on this interface (that is, the number of SVCs for which this interface represents the destination end of the call).
OBJECT-TYPE    
  Gauge32 0..992  

mscFrUniSigInCallsRefused 1.3.6.1.4.1.562.36.2.1.71.6.16.1.5
This attribute counts the incoming SVC call requests that are rejected by either this interface or by the called user. When this count exceeds the maximum, it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniSigOutCalls 1.3.6.1.4.1.562.36.2.1.71.6.16.1.6
This attribute indicates the current number of outgoing SVCs on this interface (that is, the number of SVCs for which this interface represents the source end of the call).
OBJECT-TYPE    
  Gauge32 0..992  

mscFrUniSigOutCallsFailed 1.3.6.1.4.1.562.36.2.1.71.6.16.1.7
This attribute counts the outgoing SVC call requests that are rejected by either this interface, or by the network side of the destination end, or by the called user. When this count exceeds the maximum, it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniSigProtocolErrors 1.3.6.1.4.1.562.36.2.1.71.6.16.1.8
This attribute counts the number of times a FRF.4 protocol error has occurred. Any one of the following events constitutes a protocol error: 1. In the user-signaled Link Layer Core Parameters IE within the SETUP or CONNECT messages, Cir, Bc and Be are all zero; 2. In the user-signaled Link Layer Core Parameters IE within the SETUP or CONNECT messages, Cir is zero but Bc is non-zero, or Bc is zero but Cir is non-zero; 3. In the user-signaled Link Layer Core Parameters IE within the SETUP or CONNECT messages, the Minimum Acceptable CIR is greater than Cir; 4. At the destination end, any of the destination to source direction link layer core parameters has been increased in the CONNECT message from the called user; 5. At the destination end, the destination to source direction Cir in the CONNECT message is smaller than the corresponding minimum acceptable Cir signaled to the called user; 6. At the source end, any of the source to destination direction link layer core parameters in the CONNECT message from the destination end has been increased; 7. At the source end, the source to destination direction Cir, after negotiation, is smaller than the corresponding minimum acceptable Cir; 8. The network has received a STATUS message from the user with an incompatible FRF.4 state. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniSigQualityOfServiceNotAvailable 1.3.6.1.4.1.562.36.2.1.71.6.16.1.9
This attribute counts the number of incoming and outgoing SVCs that are rejected because the quality of service requested cannot be met by the network. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniSigSetupTimeout 1.3.6.1.4.1.562.36.2.1.71.6.16.1.10
This attribute counts the number of times the T303 setup timer has expired. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniSigLastCauseInStatusMsgReceived 1.3.6.1.4.1.562.36.2.1.71.6.16.1.11
This attribute indicates the cause value in the last received user's STATUS message to an existing call. The DLCI to which this STATUS message applies is specified in the lastDlciReceivedStatus attribute. The initial value of this attribute is 0 which means that no STATUS message has been received for an existing call yet.
OBJECT-TYPE    
  Unsigned32 0..255  

mscFrUniSigLastStateInStatusMsgReceived 1.3.6.1.4.1.562.36.2.1.71.6.16.1.12
This attribute indicates the state value in the last received user's STATUS message to an existing call. The DLCI to which this STATUS message applies is specified in the lastDlciReceivedStatus attribute. The initial value of this attribute is notApplicable.
OBJECT-TYPE    
  INTEGER null(0), callInitiated(1), n2(2), outgoingCallProceeding(3), n4(4), n5(5), callPresent(6), n7(7), n8(8), incomingCallProceeding(9), active(10), disconnectRequest(11), disconnectIndication(12), n13(13), n14(14), n15(15), n16(16), n17(17), n18(18), releaseRequest(19), notApplicable(20), n21(21), n22(22), n23(23), n24(24), n25(25), n26(26), n27(27), n28(28), n29(29), n30(30), n31(31), n32(32), n33(33), n34(34), n35(35), n36(36), n37(37), n38(38), n39(39), n40(40), n41(41), n42(42), n43(43), n44(44), n45(45), n46(46), n47(47), n48(48), n49(49), n50(50), n51(51), n52(52), n53(53), n54(54), n55(55), n56(56), n57(57), n58(58), n59(59), n60(60), restartRequest(61), restart(62), n63(63)  

mscFrUniSigLastDlciReceivedStatus 1.3.6.1.4.1.562.36.2.1.71.6.16.1.13
This attribute shows the value of the DLCI that has most recently received a STATUS message from the user. The initial value of this attribute is 0.
OBJECT-TYPE    
  Unsigned32 0 | 16..1007  

mscFrUniSigLastStateReceivedStatus 1.3.6.1.4.1.562.36.2.1.71.6.16.1.14
This attribute shows the network FRF.4 state of the DLCI that has most recently received a STATUS message from the user. The DLCI to which this STATUS message applies is specified in the lastDlciReceivedStatus attribute. The initial value of this attribute is notApplicable.
OBJECT-TYPE    
  INTEGER null(0), callInitiated(1), outgoingCallProceeding(3), callPresent(6), incomingCallProceeding(9), active(10), disconnectRequest(11), disconnectIndication(12), releaseRequest(19), notApplicable(20), restartRequest(61), restart(62)  

mscFrUniSigLastTimeMsgBlockCongested 1.3.6.1.4.1.562.36.2.1.71.6.16.1.15
This attribute displays the most recent time that an SVC DLCI has failed to get a message block due to message block congestion. Exceptional behavior can occur due to this. The DLCI that has most recently encountered this is indicated by the lastDlciWithMsgBlockCongestion attribute. However, all SVC DLCIs may be affected. The initial value of this attribute is 0000-00-00 00:00.
OBJECT-TYPE    
  EnterpriseDateAndTime SIZE(0 | 16)  

mscFrUniSigLastDlciWithMsgBlockCongestion 1.3.6.1.4.1.562.36.2.1.71.6.16.1.16
This attribute shows the value of the DLCI that has most recently failed to get a message block due to message block congestion. The initial value of this attribute is 0.
OBJECT-TYPE    
  Unsigned32 0 | 16..1007  

mscFrUniSigCurrentAggregateSvcCirNormalQ 1.3.6.1.4.1.562.36.2.1.71.6.16.1.17
This attribute shows the aggregate SVC CIR (for traffic transiting in the network through normal priority queue) assigned to existing SVCs on the interface. The value of currentAggregateSvcCirNormalQ could be greater than the provisionable value of maximumAggregateSvcCiNormalQ if the value of maximumAggregateSvcCirNormalQ has been changed during the service of this FrUni.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniSigCurrentAggregateSvcCirHighQ 1.3.6.1.4.1.562.36.2.1.71.6.16.1.18
This attribute shows the aggregate SVC CIR (for traffic transiting in the network through high priority queue) assigned to existing SVCs on the interface. The value of currentAggregateSvcCirHighQ could be greater than the provisionable value of maximumAggregateSvcCirHighQ if the value of maximumAggregateSvcCirHighQ has been changed during the service of this FrUni.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniSigCurrentAggregateSvcCirInterruptQ 1.3.6.1.4.1.562.36.2.1.71.6.16.1.19
This attribute shows the aggregate SVC CIR (for traffic transiting in the network through interrupting queue) assigned to existing SVCs on the interface. The value of currentAggregateSvcCirInterruptQ could be greater than the provisionable value of maximumAggregateSvcCirInterruptQ if the value of maximumAggregateSvcCirInterruptQ has been changed during the service of this FrUni.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniSigCurrentAggregateSvcEirNormalQ 1.3.6.1.4.1.562.36.2.1.71.6.16.1.20
This attribute shows the aggregate SVC EIR (for excess traffic transiting in the network through normal priority queue) assigned to existing SVCs on the interface. The value of currentAggregateSvcEirNormalQ could be greater than the provisionable value of maximumAggregateSvcEirNormalQ if the value of maximumAggregateSvcEiNormalQ has been changed during the service of this FrUni or unlimitedAggregateEir is set to yes.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniSigCurrentAggregateSvcEirHighQ 1.3.6.1.4.1.562.36.2.1.71.6.16.1.21
This attribute shows the aggregate SVC EIR (for excess traffic transiting in the network through high priority queue) assigned to existing SVCs on the interface. The value of currentAggregateSvcEirHighQ could be greater than the provisionable value of maximumAggregateSvcEirHighQ if the value of maximumAggregateSvcEirHighQ has been changed during the service of this FrUni or unlimitedAggregateEir is set to yes.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniSigCurrentAggregateSvcEirInterruptQ 1.3.6.1.4.1.562.36.2.1.71.6.16.1.22
This attribute shows the aggregate SVC EIR (for excess traffic transiting in the network through interrupting queue) assigned to existing SVCs on the interface. The value of currentAggregateSvcEirInterruptQ could be greater than the provisionable value of maximumAggregateSvcEirInterruptQ if the value of maximumAggregateSvcEirInterruptQ has been changed during the service of this FrUni or unlimitedAggregateEir is set to yes.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniSigLapfStatusTable 1.3.6.1.4.1.562.36.2.1.71.6.17
This group contains the Q.922 SVC data link layer status.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniSigLapfStatusEntry

mscFrUniSigLapfStatusEntry 1.3.6.1.4.1.562.36.2.1.71.6.17.1
An entry in the mscFrUniSigLapfStatusTable.
OBJECT-TYPE    
  MscFrUniSigLapfStatusEntry  

mscFrUniSigCurrentState 1.3.6.1.4.1.562.36.2.1.71.6.17.1.1
This attribute shows the current state of the SVC data link layer interface.
OBJECT-TYPE    
  INTEGER disconnected(1), linkSetup(2), disconnectRequest(4), informationTransfer(5), waitingAck(7)  

mscFrUniSigLastStateChangeReason 1.3.6.1.4.1.562.36.2.1.71.6.17.1.2
This attribute shows the reason for the most recent state change. notStarted - this is the default state after SVC data link has just been created. abmeEntered - SVC data link has entered Asynchronous Balanced Mode after SABME or UA has been received. abmeReset - the data link has been reset. dmReceived - DM response received. dmSent - DM sent. discReceived - DISC response received. discSent - DISC sent. frmrReceived - FRMR received. n200RetranTimeOut - retransmitLimit has been exceeded. other - unspecified state change reasons. The most likely reason for this is the transition from state waitingAck to state informationTransfer.
OBJECT-TYPE    
  INTEGER notStarted(1), abmeEntered(3), abmeReset(5), dmReceived(6), dmSent(7), discReceived(8), discSent(9), frmrReceived(10), n200RetranTimeOut(12), other(13)  

mscFrUniSigFrmrReceive 1.3.6.1.4.1.562.36.2.1.71.6.17.1.3
This attribute shows the information field of the Frame Reject (FRMR) most recently received.
OBJECT-TYPE    
  HexString SIZE(0..8)  

mscFrUniSigCurrentQueueSize 1.3.6.1.4.1.562.36.2.1.71.6.17.1.4
This attribute shows the current number of frames in the SVC data link layer transmit queue.
OBJECT-TYPE    
  Counter32  

mscFrUniSigLapfStatsTable 1.3.6.1.4.1.562.36.2.1.71.6.18
This group contains the statistics for the SVC data link layer.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniSigLapfStatsEntry

mscFrUniSigLapfStatsEntry 1.3.6.1.4.1.562.36.2.1.71.6.18.1
An entry in the mscFrUniSigLapfStatsTable.
OBJECT-TYPE    
  MscFrUniSigLapfStatsEntry  

mscFrUniSigStateChange 1.3.6.1.4.1.562.36.2.1.71.6.18.1.1
This attribute counts the number of times the SVC data link layer interface has changed state. While the data link layer is in informationTransfer state, this counter will increment on each expiry of idleProbeTimer as its state goes from informationTransfer to waitingAck and back. When this count exceeds the maximum, it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniSigRemoteBusy 1.3.6.1.4.1.562.36.2.1.71.6.18.1.2
This attribute counts the number of times transmission of an I-frame was unsuccessful due to a perceived remote busy condition (window closed or remote busy). When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniSigReceiveRejectFrame 1.3.6.1.4.1.562.36.2.1.71.6.18.1.3
This attribute counts the number of REJ frames received by the interface. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniSigAckTimeout 1.3.6.1.4.1.562.36.2.1.71.6.18.1.4
This attribute counts the number of times the ackTimer has expired. Frequent increments of this counter indicate a problem at the link or improper values have been chosen for ackTimer and ackDelayTimer between the local and remote sides. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniSigIFramesTransmitted 1.3.6.1.4.1.562.36.2.1.71.6.18.1.5
This attribute counts the number of SVC I-frames transmitted to the interface on DLCI 0. An I-frame may be counted more than once if there are retransmissions at the SVC data link layer. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniSigIFramesTxDiscarded 1.3.6.1.4.1.562.36.2.1.71.6.18.1.6
This attribute counts the number of SVC I-frames that are bound for the link but have been discarded. Discard reasons may be one of the following: 1. the frame length is beyond the allowed limit. 2. the SVC data link layer is in disconnected state. 3. the transmit queue has been purged because the queue length has reached the reset threshold. 4. the transmit queue or the queue waiting for acknowledgment has been purged because the link cannot be re-established. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniSigIFramesReceived 1.3.6.1.4.1.562.36.2.1.71.6.18.1.7
This attribute counts the number of SVC I-frames received from the interface. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniSigIFramesRcvdDiscarded 1.3.6.1.4.1.562.36.2.1.71.6.18.1.8
This attribute counts the number of SVC I-frames received but have been discarded. The discard reasons are: 1. incorrect frame size 2. frame is out of sequence 3. frame received while the network side of the SVC data link layer is not in the informationTransfer or waitingAck state. When this count reaches maximum, it wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniSigSvcaccTable 1.3.6.1.4.1.562.36.2.1.71.6.19
This group contains the provisionable attribute which controls accounting for this interface.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniSigSvcaccEntry

mscFrUniSigSvcaccEntry 1.3.6.1.4.1.562.36.2.1.71.6.19.1
An entry in the mscFrUniSigSvcaccTable.
OBJECT-TYPE    
  MscFrUniSigSvcaccEntry  

mscFrUniSigDefaultAccounting 1.3.6.1.4.1.562.36.2.1.71.6.19.1.1
This attribute specifies whether accounting data collection and record generation is turned on for switched connections at this interface. For accounting data collection and record generation to occur, this attribute must be on and at least one of the accountCollection reasons in the Dna component must be present.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscFrUniSigCodesTable 1.3.6.1.4.1.562.36.2.1.71.6.20
This group contains the remote data network address, the last SVC clear cause and the last SVC diagnostic code coming from the subnet or the local VC.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniSigCodesEntry

mscFrUniSigCodesEntry 1.3.6.1.4.1.562.36.2.1.71.6.20.1
An entry in the mscFrUniSigCodesTable.
OBJECT-TYPE    
  MscFrUniSigCodesEntry  

mscFrUniSigLastClearRemoteDataNetworkAddress 1.3.6.1.4.1.562.36.2.1.71.6.20.1.1
This attribute indicates the Data Network Address (DNA) of the remote (the other end of the SVC connection) of the call which cleared last and whose clear and diagnostic codes were recorded.
OBJECT-TYPE    
  DigitString SIZE(0..15)  

mscFrUniSigLastClearCause 1.3.6.1.4.1.562.36.2.1.71.6.20.1.2
This attribute indicates the last SVC clear cause signalled at the end of the connection or failure to connect. It is updated only if the clear request comes from the subnet or the call is rejected locally by the VC. The same set of possible values provides the clear cause field in the accounting record.
OBJECT-TYPE    
  Unsigned32 0..255  

mscFrUniSigLastDiagnosticCode 1.3.6.1.4.1.562.36.2.1.71.6.20.1.3
This attribute indicates the last SVC diagnostic code signalled at the end of the connection or failure to connect. It is updated if the clear request comes from the subnet or the call is rejected locally by the VC. The same set of possible values provides the diagnostic code field in the accounting record.
OBJECT-TYPE    
  Unsigned32 0..255  

mscFrUniSigBandwidthNotAvailableTable 1.3.6.1.4.1.562.36.2.1.71.6.711
This attribute counts the number of call failures for each bandwidth pool due to the requested bandwidth not being available.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniSigBandwidthNotAvailableEntry

mscFrUniSigBandwidthNotAvailableEntry 1.3.6.1.4.1.562.36.2.1.71.6.711.1
An entry in the mscFrUniSigBandwidthNotAvailableTable.
OBJECT-TYPE    
  MscFrUniSigBandwidthNotAvailableEntry  

mscFrUniSigBandwidthNotAvailableIndex 1.3.6.1.4.1.562.36.2.1.71.6.711.1.1
This variable represents the mscFrUniSigBandwidthNotAvailableTable specific index for the mscFrUniSigBandwidthNotAvailableTable.
OBJECT-TYPE    
  Integer32 0..15  

mscFrUniSigBandwidthNotAvailableValue 1.3.6.1.4.1.562.36.2.1.71.6.711.1.2
This variable represents an individual value for the mscFrUniSigBandwidthNotAvailableTable.
OBJECT-TYPE    
  Counter32  

mscFrUniVFramer 1.3.6.1.4.1.562.36.2.1.71.8
OBJECT IDENTIFIER    

mscFrUniVFramerRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.8.1
This entry controls the addition and deletion of mscFrUniVFramer components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniVFramerRowStatusEntry

mscFrUniVFramerRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.8.1.1
A single entry in the table represents a single mscFrUniVFramer component.
OBJECT-TYPE    
  MscFrUniVFramerRowStatusEntry  

mscFrUniVFramerRowStatus 1.3.6.1.4.1.562.36.2.1.71.8.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniVFramer components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniVFramerComponentName 1.3.6.1.4.1.562.36.2.1.71.8.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniVFramerStorageType 1.3.6.1.4.1.562.36.2.1.71.8.1.1.4
This variable represents the storage type value for the mscFrUniVFramer tables.
OBJECT-TYPE    
  StorageType  

mscFrUniVFramerIndex 1.3.6.1.4.1.562.36.2.1.71.8.1.1.10
This variable represents the index for the mscFrUniVFramer tables.
OBJECT-TYPE    
  NonReplicated  

mscFrUniVFramerProvTable 1.3.6.1.4.1.562.36.2.1.71.8.10
This group contains provisionable attributes for the VirtualFramer component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniVFramerProvEntry

mscFrUniVFramerProvEntry 1.3.6.1.4.1.562.36.2.1.71.8.10.1
An entry in the mscFrUniVFramerProvTable.
OBJECT-TYPE    
  MscFrUniVFramerProvEntry  

mscFrUniVFramerOtherVirtualFramer 1.3.6.1.4.1.562.36.2.1.71.8.10.1.1
This attribute specifies the other VirtualFramer to which the service is linked, for example, FrUni/n VirtualFramer, FrDte/n VirtualFramer.
OBJECT-TYPE    
  Link  

mscFrUniVFramerLogicalProcessor 1.3.6.1.4.1.562.36.2.1.71.8.10.1.2
This attribute specifies the logical processor on which the service component will reside.
OBJECT-TYPE    
  Link  

mscFrUniVFramerStateTable 1.3.6.1.4.1.562.36.2.1.71.8.11
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniVFramerStateEntry

mscFrUniVFramerStateEntry 1.3.6.1.4.1.562.36.2.1.71.8.11.1
An entry in the mscFrUniVFramerStateTable.
OBJECT-TYPE    
  MscFrUniVFramerStateEntry  

mscFrUniVFramerAdminState 1.3.6.1.4.1.562.36.2.1.71.8.11.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscFrUniVFramerOperationalState 1.3.6.1.4.1.562.36.2.1.71.8.11.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscFrUniVFramerUsageState 1.3.6.1.4.1.562.36.2.1.71.8.11.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscFrUniVFramerStatsTable 1.3.6.1.4.1.562.36.2.1.71.8.12
This group contains the operational statistics data for a VirtualFramer component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniVFramerStatsEntry

mscFrUniVFramerStatsEntry 1.3.6.1.4.1.562.36.2.1.71.8.12.1
An entry in the mscFrUniVFramerStatsTable.
OBJECT-TYPE    
  MscFrUniVFramerStatsEntry  

mscFrUniVFramerFrmToOtherVFramer 1.3.6.1.4.1.562.36.2.1.71.8.12.1.2
This attribute counts the frames transmitted to the otherVirtualFramer.
OBJECT-TYPE    
  PassportCounter64  

mscFrUniVFramerFrmFromOtherVFramer 1.3.6.1.4.1.562.36.2.1.71.8.12.1.3
This attribute counts the frames received from the otherVirtualFramer.
OBJECT-TYPE    
  PassportCounter64  

mscFrUniVFramerOctetFromOtherVFramer 1.3.6.1.4.1.562.36.2.1.71.8.12.1.5
This attribute counts the octets received from the otherVirtualFramer.
OBJECT-TYPE    
  PassportCounter64  

mscFrUniLts 1.3.6.1.4.1.562.36.2.1.71.9
OBJECT IDENTIFIER    

mscFrUniLtsRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.9.1
This entry controls the addition and deletion of mscFrUniLts components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniLtsRowStatusEntry

mscFrUniLtsRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.9.1.1
A single entry in the table represents a single mscFrUniLts component.
OBJECT-TYPE    
  MscFrUniLtsRowStatusEntry  

mscFrUniLtsRowStatus 1.3.6.1.4.1.562.36.2.1.71.9.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniLts components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniLtsComponentName 1.3.6.1.4.1.562.36.2.1.71.9.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniLtsStorageType 1.3.6.1.4.1.562.36.2.1.71.9.1.1.4
This variable represents the storage type value for the mscFrUniLts tables.
OBJECT-TYPE    
  StorageType  

mscFrUniLtsIndex 1.3.6.1.4.1.562.36.2.1.71.9.1.1.10
This variable represents the index for the mscFrUniLts tables.
OBJECT-TYPE    
  NonReplicated  

mscFrUniLtsPat 1.3.6.1.4.1.562.36.2.1.71.9.2
OBJECT IDENTIFIER    

mscFrUniLtsPatRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.9.2.1
This entry controls the addition and deletion of mscFrUniLtsPat components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniLtsPatRowStatusEntry

mscFrUniLtsPatRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.9.2.1.1
A single entry in the table represents a single mscFrUniLtsPat component.
OBJECT-TYPE    
  MscFrUniLtsPatRowStatusEntry  

mscFrUniLtsPatRowStatus 1.3.6.1.4.1.562.36.2.1.71.9.2.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniLtsPat components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniLtsPatComponentName 1.3.6.1.4.1.562.36.2.1.71.9.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniLtsPatStorageType 1.3.6.1.4.1.562.36.2.1.71.9.2.1.1.4
This variable represents the storage type value for the mscFrUniLtsPat tables.
OBJECT-TYPE    
  StorageType  

mscFrUniLtsPatIndex 1.3.6.1.4.1.562.36.2.1.71.9.2.1.1.10
This variable represents the index for the mscFrUniLtsPat tables.
OBJECT-TYPE    
  Integer32 0..29  

mscFrUniLtsPatDefaultsTable 1.3.6.1.4.1.562.36.2.1.71.9.2.10
This attribute group contains the specifications of the pattern.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniLtsPatDefaultsEntry

mscFrUniLtsPatDefaultsEntry 1.3.6.1.4.1.562.36.2.1.71.9.2.10.1
An entry in the mscFrUniLtsPatDefaultsTable.
OBJECT-TYPE    
  MscFrUniLtsPatDefaultsEntry  

mscFrUniLtsPatDefaultDlci 1.3.6.1.4.1.562.36.2.1.71.9.2.10.1.200
This attribute specifies for which dlci (on the local end) the frames are destined.
OBJECT-TYPE    
  Unsigned32 16..1007  

mscFrUniLtsPatDefaultNumFrames 1.3.6.1.4.1.562.36.2.1.71.9.2.10.1.201
This attribute specifies the number of frames in this pattern. This is the number of frames of this type which will be generated in one timeInterval.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniLtsPatDefaultDataSize 1.3.6.1.4.1.562.36.2.1.71.9.2.10.1.202
This attribute specifies the payload size of each frame in bytes. This is in excess to the header.
OBJECT-TYPE    
  Unsigned32 0..8200  

mscFrUniLtsPatDefaultHeaderBits 1.3.6.1.4.1.562.36.2.1.71.9.2.10.1.203
This attribute specifies whether the following bits are on/off in the header of each frame. The following bits can be set: BeCn, C/R, De, FeCn Description of bits: becn(0) fecn(1) cr(2) de(3)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscFrUniLtsPatDefaultHeaderLength 1.3.6.1.4.1.562.36.2.1.71.9.2.10.1.204
This attribute specifies the size of the frame relay header in bytes. Passport currently only supports a 2-byte header.
OBJECT-TYPE    
  Unsigned32 0 | 2..4  

mscFrUniLtsPatDefaultEABits 1.3.6.1.4.1.562.36.2.1.71.9.2.10.1.205
This attribute specifies how the address field extension bits are set in the frame header. Consider the value to be a four bit binary number. For example, 4 = 0100. Only the first headerLength bits are used. For instance, suppose headerLength is 3, then the appropriate EABits is 2, or 0010. This attribute can be used to create a header of length greater than two bytes or to specify incorrect EABits in the header.
OBJECT-TYPE    
  Hex 0..15  

mscFrUniLtsPatDefaultPayloadPattern 1.3.6.1.4.1.562.36.2.1.71.9.2.10.1.206
This attribute specifies the payload of each frame. The value specified is in hexadecimal, where every two digits represent a byte. A maximum of 24 digits (12 bytes) may be set, after which the pattern will repeat in the payload (depending on repeatPattern attribute). NOTE: If a RFC 1490 header is specified, via the 1490Header attribute, the specified pattern will begin following the header (i.e. at the 9th byte in the payload).
OBJECT-TYPE    
  HexString SIZE(1..12)  

mscFrUniLtsPatDefaultRfc1490Header 1.3.6.1.4.1.562.36.2.1.71.9.2.10.1.207
This attribute specifies the appropriate RFC 1490 encapsulated header of the frame. A value of 0 indicates no 1490 header. NOTE: This header resides in the first 8 bytes of the payload. If the specified value is non-zero, then the payload pattern provisioned will begin at the 9th byte.
OBJECT-TYPE    
  INTEGER n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15), n16(16), n17(17), none(18)  

mscFrUniLtsPatDefaultUseBadLrc 1.3.6.1.4.1.562.36.2.1.71.9.2.10.1.208
This attribute specifies whether the frames from this pattern are to have a bad LRC prior to being sent to the framer. The LRC is checked while the frame is being put onto the link and the failure should cause an abort frame to be sent.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mscFrUniLtsPatSetupTable 1.3.6.1.4.1.562.36.2.1.71.9.2.11
This attribute group contains the specifications of the pattern.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniLtsPatSetupEntry

mscFrUniLtsPatSetupEntry 1.3.6.1.4.1.562.36.2.1.71.9.2.11.1
An entry in the mscFrUniLtsPatSetupTable.
OBJECT-TYPE    
  MscFrUniLtsPatSetupEntry  

mscFrUniLtsPatDlci 1.3.6.1.4.1.562.36.2.1.71.9.2.11.1.200
This attribute specifies for which dlci (on the local end) the frames are destined.
OBJECT-TYPE    
  Unsigned32 16..1007  

mscFrUniLtsPatNumFrames 1.3.6.1.4.1.562.36.2.1.71.9.2.11.1.201
This attribute specifies the number of frames in this pattern. This is the number of frames of this type which will be generated in one timeInterval.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniLtsPatDataSize 1.3.6.1.4.1.562.36.2.1.71.9.2.11.1.202
This attribute specifies the payload size of each frame in bytes. This is in excess to the header.
OBJECT-TYPE    
  Unsigned32 0..8200  

mscFrUniLtsPatHeaderBits 1.3.6.1.4.1.562.36.2.1.71.9.2.11.1.203
This attribute specifies whether the following bits are on/off in the header of each frame. The following bits can be set: BeCn, C/R, De, FeCn Description of bits: becn(0) fecn(1) cr(2) de(3)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscFrUniLtsPatHeaderLength 1.3.6.1.4.1.562.36.2.1.71.9.2.11.1.204
This attribute specifies the size of the frame relay header in bytes. Passport currently only supports a 2-byte header. Valid values are 0, 2, 3, 4. 0 indicates to use no header. That is, the frame will start with either the payload or rfc1490 header.
OBJECT-TYPE    
  Unsigned32 0 | 2..4  

mscFrUniLtsPatEaBits 1.3.6.1.4.1.562.36.2.1.71.9.2.11.1.205
This attribute specifies how the address field extension bits are set in the frame header. Consider the value to be a four bit binary number. For example, 4 = 0100. Only the first headerLength bits are used. For instance, suppose headerLength is 3, then the appropriate eaBits is 2, or 0010. This attribute can be used to create a header of length greater than two bytes or to specify incorrect eaBits in the header.
OBJECT-TYPE    
  Hex 0..15  

mscFrUniLtsPatPayloadPattern 1.3.6.1.4.1.562.36.2.1.71.9.2.11.1.206
This attribute specifies the payload of each frame. The value specified is in hexadecimal, where every two digits represent a byte. A maximum of 24 digits (12 bytes) may be set, after which the pattern will repeat in the payload (depending on repeatPattern attribute). NOTE: If a RFC 1490 header is specified, via the 1490Header attribute, the specified pattern will begin following the header (i.e. at the 9th byte in the payload).
OBJECT-TYPE    
  HexString SIZE(1..12)  

mscFrUniLtsPatRfc1490Header 1.3.6.1.4.1.562.36.2.1.71.9.2.11.1.207
This attribute specifies the appropriate RFC 1490 encapsulated header of the frame. A value of 0 indicates no 1490 header. NOTE: This header resides in the first 8 bytes of the payload. If the specified value is non-zero, then the payload pattern provisioned will begin at the 9th byte.
OBJECT-TYPE    
  INTEGER n0(0), n1(1), n2(2), n3(3), n4(4), n5(5), n6(6), n7(7), n8(8), n9(9), n10(10), n11(11), n12(12), n13(13), n14(14), n15(15), n16(16), n17(17), none(18)  

mscFrUniLtsPatUseBadLrc 1.3.6.1.4.1.562.36.2.1.71.9.2.11.1.208
This attribute specifies whether the frames from this pattern are to have a bad LRC prior to being sent to the framer. The LRC is checked while the frame is being put onto the link and the failure should cause an abort frame to be sent.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mscFrUniLtsPatOpDataTable 1.3.6.1.4.1.562.36.2.1.71.9.2.12
This group contains the operational attributes which allow changing the pattern outside of provisioning mode.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniLtsPatOpDataEntry

mscFrUniLtsPatOpDataEntry 1.3.6.1.4.1.562.36.2.1.71.9.2.12.1
An entry in the mscFrUniLtsPatOpDataTable.
OBJECT-TYPE    
  MscFrUniLtsPatOpDataEntry  

mscFrUniLtsPatFramePattern 1.3.6.1.4.1.562.36.2.1.71.9.2.12.1.200
This attribute displays the first 20 to 24 bytes of the frame payload, depending on the frame relay header size selected. This attribute represents the frame if it were at least 20 to 24 bytes in size. That is, the actual frame may be smaller.
OBJECT-TYPE    
  HexString SIZE(20..24)  

mscFrUniLtsPatHdlcBitsInserted 1.3.6.1.4.1.562.36.2.1.71.9.2.12.1.201
This attribute displays how many times a zero bit will be inserted after 5 consecutive 1 bits when a frame from this pattern is sent out.
OBJECT-TYPE    
  Unsigned32 0..65535  

mscFrUniLtsPatOpStateTable 1.3.6.1.4.1.562.36.2.1.71.9.2.13
This group contains the attributes containing the operational statistics of the pattern.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniLtsPatOpStateEntry

mscFrUniLtsPatOpStateEntry 1.3.6.1.4.1.562.36.2.1.71.9.2.13.1
An entry in the mscFrUniLtsPatOpStateTable.
OBJECT-TYPE    
  MscFrUniLtsPatOpStateEntry  

mscFrUniLtsPatLoad 1.3.6.1.4.1.562.36.2.1.71.9.2.13.1.200
This attribute indicates the load due to this particular pattern. The loads associated with all of the provisioned patterns are summed to arrive at the FrLts load.
OBJECT-TYPE    
  FixedPoint3 0..4294967295  

mscFrUniLtsPatStatus 1.3.6.1.4.1.562.36.2.1.71.9.2.13.1.201
This attributes specifies the administrative state of the pattern. A disabled pattern will not be generated, although it can still be triggered.
OBJECT-TYPE    
  INTEGER enabled(0), disabled(1)  

mscFrUniLtsSetupTable 1.3.6.1.4.1.562.36.2.1.71.9.10
This attribute group contains the parameters used to configure the behavior of the Frame Relay Load Test System.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniLtsSetupEntry

mscFrUniLtsSetupEntry 1.3.6.1.4.1.562.36.2.1.71.9.10.1
An entry in the mscFrUniLtsSetupTable.
OBJECT-TYPE    
  MscFrUniLtsSetupEntry  

mscFrUniLtsDuration 1.3.6.1.4.1.562.36.2.1.71.9.10.1.200
This attribute specifies the duration of the test in milliseconds. The test will run until the duration expires or the STOP command is issued. A value of 0 is used to indicate infinity.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniLtsAlgorithm 1.3.6.1.4.1.562.36.2.1.71.9.10.1.201
This attribute specifies which algorithm is used to generate the frames. ContinuousBurst This mode of traffic generation creates traffic at the maximum rate possible until all of the frames have been sent. The generator then waits until the end of the timeInterval to begin again. IntervalBurst This algorithm attempts to generate 10 ms bursts of burstSize frames. It will generate as many of the burstSize frames as it can per sub-interval. DelayedBurst This algorithm generates bursts of burstSize frames separated by 10 ms delays. FixedBurst This aglorithm is similar to IntervalBurst, except a fixed burst size of 12 frames is used. delayMeasurement This algorithm is used to measure delay. The specified number of frames in the indicated pattern are generated, one at a time, with a maximum wait of maxDelay before sending the next frame. This algorithm is not implemented yet.
OBJECT-TYPE    
  INTEGER continousBurst(0), intervalBurst(1), delayBurst(2), fixedBurst(3)  

mscFrUniLtsBurstSize 1.3.6.1.4.1.562.36.2.1.71.9.10.1.204
This attribute specifies the number of frames per burst under the delayedBurst and intervalBurst algorithms.
OBJECT-TYPE    
  Unsigned32 1..250  

mscFrUniLtsTimeInterval 1.3.6.1.4.1.562.36.2.1.71.9.10.1.205
This attribute specifies the time interval to the specified number of seconds. Granuality is in centiseconds. Maximum is 1 minute.
OBJECT-TYPE    
  Unsigned32 1..60000  

mscFrUniLtsStateTable 1.3.6.1.4.1.562.36.2.1.71.9.11
This group contains the operation statistics of the load generator.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniLtsStateEntry

mscFrUniLtsStateEntry 1.3.6.1.4.1.562.36.2.1.71.9.11.1
An entry in the mscFrUniLtsStateTable.
OBJECT-TYPE    
  MscFrUniLtsStateEntry  

mscFrUniLtsGeneratorState 1.3.6.1.4.1.562.36.2.1.71.9.11.1.200
This attribute indicates whether the Lts is generating traffic.
OBJECT-TYPE    
  INTEGER stopped(0), running(1)  

mscFrUniLtsCycleIncomplete 1.3.6.1.4.1.562.36.2.1.71.9.11.1.201
This attribute indicates whether the time required to generate all of the enabled patterns is more than timeInterval by a true value. Otherwise, this flag is set to false. Default is True.
OBJECT-TYPE    
  INTEGER false(0), true(1)  

mscFrUniLtsLastActiveInterval 1.3.6.1.4.1.562.36.2.1.71.9.11.1.202
This attribute indicates the actual time it took to generate all of the enabled patterns in the last cycle. If cycleIncomplete is true, this value should be zero.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniLtsLoad 1.3.6.1.4.1.562.36.2.1.71.9.11.1.204
This attribute indicates the load being generated. This value represents that calculated using the set number of ticks. The actual burstTimeInterval may differ. One entire cycle of the patterns is completed in activeInterval and thus most of the load may be concentrated early in the set interval.
OBJECT-TYPE    
  FixedPoint3 0..4294967295  

mscFrUniLtsElapsedGenerationTime 1.3.6.1.4.1.562.36.2.1.71.9.11.1.205
This attribute indicates how many milliseconds have elapsed since the start of this test.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniLtsResultsTable 1.3.6.1.4.1.562.36.2.1.71.9.12
This group contains the frame counting attributes for the LTS component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniLtsResultsEntry

mscFrUniLtsResultsEntry 1.3.6.1.4.1.562.36.2.1.71.9.12.1
An entry in the mscFrUniLtsResultsTable.
OBJECT-TYPE    
  MscFrUniLtsResultsEntry  

mscFrUniLtsFramesTx 1.3.6.1.4.1.562.36.2.1.71.9.12.1.200
This attribute specifies the number of frames send to the network since the last time these statistics were cleared. This is similar to the framesToIf attribute of the FRAMER component.
OBJECT-TYPE    
  Counter32  

mscFrUniLtsBytesTx 1.3.6.1.4.1.562.36.2.1.71.9.12.1.204
This attribute indicates the number of bytes sent.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniLtsBitRateTx 1.3.6.1.4.1.562.36.2.1.71.9.12.1.208
This attribute indicates the bit rate being sent to the link. It should only differ from the load if the burstTimeInterval would be >= the timeInterval or burstSize frames cannot be generated in 10ms (intervalBurst algorithm).
OBJECT-TYPE    
  FixedPoint3 0..4294967295  

mscFrUniLtsFrameRateTx 1.3.6.1.4.1.562.36.2.1.71.9.12.1.209
This attribute indicates the frame rate being sent to the link. It is calculated using the number of frames sent to the link in one cycle of the patterns.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniCidDataTable 1.3.6.1.4.1.562.36.2.1.71.10
This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCidDataEntry

mscFrUniCidDataEntry 1.3.6.1.4.1.562.36.2.1.71.10.1
An entry in the mscFrUniCidDataTable.
OBJECT-TYPE    
  MscFrUniCidDataEntry  

mscFrUniCustomerIdentifier 1.3.6.1.4.1.562.36.2.1.71.10.1.1
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
OBJECT-TYPE    
  Unsigned32 0 | 1..8191  

mscFrUniStateTable 1.3.6.1.4.1.562.36.2.1.71.11
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniStateEntry

mscFrUniStateEntry 1.3.6.1.4.1.562.36.2.1.71.11.1
An entry in the mscFrUniStateTable.
OBJECT-TYPE    
  MscFrUniStateEntry  

mscFrUniAdminState 1.3.6.1.4.1.562.36.2.1.71.11.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscFrUniOperationalState 1.3.6.1.4.1.562.36.2.1.71.11.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscFrUniUsageState 1.3.6.1.4.1.562.36.2.1.71.11.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscFrUniAvailabilityStatus 1.3.6.1.4.1.562.36.2.1.71.11.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

mscFrUniProceduralStatus 1.3.6.1.4.1.562.36.2.1.71.11.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscFrUniControlStatus 1.3.6.1.4.1.562.36.2.1.71.11.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscFrUniAlarmStatus 1.3.6.1.4.1.562.36.2.1.71.11.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscFrUniStandbyStatus 1.3.6.1.4.1.562.36.2.1.71.11.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
OBJECT-TYPE    
  INTEGER hotStandby(0), coldStandby(1), providingService(2), notSet(15)  

mscFrUniUnknownStatus 1.3.6.1.4.1.562.36.2.1.71.11.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
OBJECT-TYPE    
  INTEGER false(0), true(1)  

mscFrUniStatsTable 1.3.6.1.4.1.562.36.2.1.71.12
FrUni/n Statistics This group contains the statistics about the operational behavior of the service at the interface level.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniStatsEntry

mscFrUniStatsEntry 1.3.6.1.4.1.562.36.2.1.71.12.1
An entry in the mscFrUniStatsTable.
OBJECT-TYPE    
  MscFrUniStatsEntry  

mscFrUniLastUnknownDlci 1.3.6.1.4.1.562.36.2.1.71.12.1.1
This attribute identifies the most recent DLCI which user frames were received on for which a DLCI has not been provisioned on the port.
OBJECT-TYPE    
  Unsigned32 0..1023  

mscFrUniUnknownDlciFramesFromIf 1.3.6.1.4.1.562.36.2.1.71.12.1.2
This attribute contains a count of the number of frames received from the interface with an unknown DLCI (DLCI which is not provisioned). When the maximum is reached the count wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniInvalidHeaderFramesFromIf 1.3.6.1.4.1.562.36.2.1.71.12.1.3
This attribute counts the number of frames received from the interface with an invalid header format. When the maximum is reached the count wraps to zero.
OBJECT-TYPE    
  Counter32  

mscFrUniIfEntryTable 1.3.6.1.4.1.562.36.2.1.71.13
This group contains the provisionable attributes for the ifEntry.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniIfEntryEntry

mscFrUniIfEntryEntry 1.3.6.1.4.1.562.36.2.1.71.13.1
An entry in the mscFrUniIfEntryTable.
OBJECT-TYPE    
  MscFrUniIfEntryEntry  

mscFrUniIfAdminStatus 1.3.6.1.4.1.562.36.2.1.71.13.1.1
The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mscFrUniIfIndex 1.3.6.1.4.1.562.36.2.1.71.13.1.2
This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
OBJECT-TYPE    
  InterfaceIndex 1..65535  

mscFrUniOperStatusTable 1.3.6.1.4.1.562.36.2.1.71.14
This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniOperStatusEntry

mscFrUniOperStatusEntry 1.3.6.1.4.1.562.36.2.1.71.14.1
An entry in the mscFrUniOperStatusTable.
OBJECT-TYPE    
  MscFrUniOperStatusEntry  

mscFrUniSnmpOperStatus 1.3.6.1.4.1.562.36.2.1.71.14.1.1
The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mscFrUniEmissionPriorityQsTable 1.3.6.1.4.1.562.36.2.1.71.15
This group contains the provisionable attribute to specifie the number of Frame Relay egress emission priority queues to be used on that Frame Relay Interface
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniEmissionPriorityQsEntry

mscFrUniEmissionPriorityQsEntry 1.3.6.1.4.1.562.36.2.1.71.15.1
An entry in the mscFrUniEmissionPriorityQsTable.
OBJECT-TYPE    
  MscFrUniEmissionPriorityQsEntry  

mscFrUniNumberOfEmissionQs 1.3.6.1.4.1.562.36.2.1.71.15.1.1
This attribute specifies the number of egress emission priority queues that will be used for that Frame Relay interface. The possible values of this attribute are 2 or 4: For V.35, V.11, HSSI, E1, DS1, E3, DS3 or 8pDS1 the possible values are: 2 (in which case they are hardware queues), or 4 (in which case they are software queues). For DS1C, E1C or DS3C the possible values are 2, 4 (in all cases they are software queues).
OBJECT-TYPE    
  Unsigned32 2 | 4  

mscFrUniCa 1.3.6.1.4.1.562.36.2.1.71.101
OBJECT IDENTIFIER    

mscFrUniCaRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.101.1
This entry controls the addition and deletion of mscFrUniCa components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaRowStatusEntry

mscFrUniCaRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.101.1.1
A single entry in the table represents a single mscFrUniCa component.
OBJECT-TYPE    
  MscFrUniCaRowStatusEntry  

mscFrUniCaRowStatus 1.3.6.1.4.1.562.36.2.1.71.101.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniCa components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniCaComponentName 1.3.6.1.4.1.562.36.2.1.71.101.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniCaStorageType 1.3.6.1.4.1.562.36.2.1.71.101.1.1.4
This variable represents the storage type value for the mscFrUniCa tables.
OBJECT-TYPE    
  StorageType  

mscFrUniCaIndex 1.3.6.1.4.1.562.36.2.1.71.101.1.1.10
This variable represents the index for the mscFrUniCa tables.
OBJECT-TYPE    
  NonReplicated  

mscFrUniCaTpm 1.3.6.1.4.1.562.36.2.1.71.101.2
OBJECT IDENTIFIER    

mscFrUniCaTpmRowStatusTable 1.3.6.1.4.1.562.36.2.1.71.101.2.1
This entry controls the addition and deletion of mscFrUniCaTpm components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaTpmRowStatusEntry

mscFrUniCaTpmRowStatusEntry 1.3.6.1.4.1.562.36.2.1.71.101.2.1.1
A single entry in the table represents a single mscFrUniCaTpm component.
OBJECT-TYPE    
  MscFrUniCaTpmRowStatusEntry  

mscFrUniCaTpmRowStatus 1.3.6.1.4.1.562.36.2.1.71.101.2.1.1.1
This variable is used as the basis for SNMP naming of mscFrUniCaTpm components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscFrUniCaTpmComponentName 1.3.6.1.4.1.562.36.2.1.71.101.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscFrUniCaTpmStorageType 1.3.6.1.4.1.562.36.2.1.71.101.2.1.1.4
This variable represents the storage type value for the mscFrUniCaTpm tables.
OBJECT-TYPE    
  StorageType  

mscFrUniCaTpmIndex 1.3.6.1.4.1.562.36.2.1.71.101.2.1.1.10
This variable represents the index for the mscFrUniCaTpm tables.
OBJECT-TYPE    
  Integer32 0..15  

mscFrUniCaTpmProvTable 1.3.6.1.4.1.562.36.2.1.71.101.2.10
This attribute group contains the provisionable attributes of the Tpm component at this interface.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaTpmProvEntry

mscFrUniCaTpmProvEntry 1.3.6.1.4.1.562.36.2.1.71.101.2.10.1
An entry in the mscFrUniCaTpmProvTable.
OBJECT-TYPE    
  MscFrUniCaTpmProvEntry  

mscFrUniCaTpmAssignedIngressBandwidthPool 1.3.6.1.4.1.562.36.2.1.71.101.2.10.1.2
This attribute specifies the ingress bandwidth pool which is used to support this transfer priority at this interface. When this attribute is set to sameAsModule, the bandwidth pool that is used is obtained from the assignedIngressBandwidthPool attribute under the Mod Frs DprsNet Tpm/n component. VALUES ( 16 = sameAsModule )
OBJECT-TYPE    
  Unsigned32 0..15 | 16  

mscFrUniCaTpmAssignedEgressBandwidthPool 1.3.6.1.4.1.562.36.2.1.71.101.2.10.1.3
This attribute specifies the egress bandwidth pool which is used to support this transfer priority at this interface. When this attribute is set to sameAsModule, the bandwidth pool that is used is obtained from the assignedEgressBandwidthPool attribute under the Mod Frs DprsNet Tpm/n component. VALUES ( 16 = sameAsModule )
OBJECT-TYPE    
  Unsigned32 0..15 | 16  

mscFrUniCaProvTable 1.3.6.1.4.1.562.36.2.1.71.101.10
This attribute group contains the common provisionable attributes of the Ca component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaProvEntry

mscFrUniCaProvEntry 1.3.6.1.4.1.562.36.2.1.71.101.10.1
An entry in the mscFrUniCaProvTable.
OBJECT-TYPE    
  MscFrUniCaProvEntry  

mscFrUniCaOverrideLinkRate 1.3.6.1.4.1.562.36.2.1.71.101.10.1.2
This attribute allows the link rate to be overridden for this interface. This allows the user to specify a value other than the actual physical link rate computed when a Framer component is provisioned. When a VFramer component is provisioned, this attribute overrides a link rate set to the maximum value supported by CAC . This attribute serves to provide the user control on the amount of bandwidth available for performing CAC.
OBJECT-TYPE    
  Unsigned32 0..429496729  

mscFrUniCaMaximumBandwidthPerCall 1.3.6.1.4.1.562.36.2.1.71.101.10.1.3
This attribute specifies the maximum bandwidth that can be allocated per connection.
OBJECT-TYPE    
  Unsigned32 0..520000000  

mscFrUniCaIngressCacTable 1.3.6.1.4.1.562.36.2.1.71.101.11
This attribute group contains the common provisionable attributes for ingress call admission control.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaIngressCacEntry

mscFrUniCaIngressCacEntry 1.3.6.1.4.1.562.36.2.1.71.101.11.1
An entry in the mscFrUniCaIngressCacTable.
OBJECT-TYPE    
  MscFrUniCaIngressCacEntry  

mscFrUniCaIngressApplyToCos 1.3.6.1.4.1.562.36.2.1.71.101.11.1.2
This attribute specifies which Classes of Service (CoS) have ingress Call Admission Control (CAC) applied to them. Ingress CAC applies only to swithced connections (SVCs and S-SPVCs). none - Ingress CAC is turned off for all classes of service. cirOnly - Ingress CAC is applied only to the CIR portion of a connection's bandwidth requirements for CIR>0 classes of service. cirAndEir - Ingress CAC is applied to both CIR and EIR portions of a connections bandwidth requirements for all classes of service.
OBJECT-TYPE    
  INTEGER none(0), cirOnly(1), cirAndEir(2)  

mscFrUniCaIngressMaximumEirOnlyCalls 1.3.6.1.4.1.562.36.2.1.71.101.11.1.4
This attribute specifies the maximum number of connections in the ingress direction with EIR only traffic that can be up at a given time.
OBJECT-TYPE    
  Unsigned32 0..992  

mscFrUniCaEgressCacTable 1.3.6.1.4.1.562.36.2.1.71.101.12
This attribute group contains the common provisionable attributes for egress call admission control.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaEgressCacEntry

mscFrUniCaEgressCacEntry 1.3.6.1.4.1.562.36.2.1.71.101.12.1
An entry in the mscFrUniCaEgressCacTable.
OBJECT-TYPE    
  MscFrUniCaEgressCacEntry  

mscFrUniCaEgressApplyToCos 1.3.6.1.4.1.562.36.2.1.71.101.12.1.2
This attribute specifies which Classes of Service (CoS) have egress Call Admission Control (CAC) applied to them. Egress CAC applies only to swithced connections (SVCs and S-SPVCs). none - Egress CAC is turned off for all classes of service. cirOnly - Egress CAC is applied only to the CIR portion of a connection's bandwidth requirements for CIR>0 classes of service. cirAndEir - Egress CAC is applied to both CIR and EIR portions of a connections bandwidth requirements for all classes of service.
OBJECT-TYPE    
  INTEGER none(0), cirOnly(1), cirAndEir(2)  

mscFrUniCaEgressMaximumEirOnlyCalls 1.3.6.1.4.1.562.36.2.1.71.101.12.1.4
This attribute specifies the maximum number of connections in the egress direction with EIR only traffic that can be up at a given time.
OBJECT-TYPE    
  Unsigned32 0..992  

mscFrUniCaOpTable 1.3.6.1.4.1.562.36.2.1.71.101.13
This attribute group contains the operational status of the Ca component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaOpEntry

mscFrUniCaOpEntry 1.3.6.1.4.1.562.36.2.1.71.101.13.1
An entry in the mscFrUniCaOpTable.
OBJECT-TYPE    
  MscFrUniCaOpEntry  

mscFrUniCaLinkRate 1.3.6.1.4.1.562.36.2.1.71.101.13.1.2
This attribute indicates the link rate used by both ingress and egress CAC to calculate the effective bandwidth pool sizes. If the provisionable attribute overrideLinkRate under this component is 0, then the link rate reported is the actual link rate of the port or channel. Otherwise, the link rate reported is the overrideLinkRate under this component.
OBJECT-TYPE    
  Unsigned32 0..520000000  

mscFrUniCaNumberRejectedEgressCirPermConn 1.3.6.1.4.1.562.36.2.1.71.101.13.1.681
This attribute indicates the number of permanent connections (that is, PVC and P-SPVC) that are rejected by egress CAC. A connection is rejected by egress CAC if it requests more egress CIR bandwidth than is available, and the egressApplyToCos attribute is set to either cirOnly or cirAndEir.
OBJECT-TYPE    
  Gauge32 0..992  

mscFrUniCaNumberRejectedEgressEirPermConn 1.3.6.1.4.1.562.36.2.1.71.101.13.1.682
This attribute indicates the number of permanent connections (that is, PVC and P-SPVC) that are rejected by egress CAC. A connection is rejected by egress CAC if it requests more egress EIR bandwidth than is available, and the egressApplyToCos attribute is set to cirAndEir.
OBJECT-TYPE    
  Gauge32 0..992  

mscFrUniCaIngCirBPTable 1.3.6.1.4.1.562.36.2.1.71.101.666
Port capacity is partitioned into 16 pools (pool 0 through pool 15) for the ingress CIR traffic. This attribute specifies the percentage of port capacity that is allowed for each pool. The percentage for each pool ranges from 0% to 1000% of the link rate. It allows for under or over subscription of the port. Under subscription occurs when the sum of the percentages assigned to the 16 pools is less than 100%. Over subscription occurs when the sum of the percentages for the 16 pools exceeds 100%. The default is full sharing of port capacity with three pre-set partitions.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaIngCirBPEntry

mscFrUniCaIngCirBPEntry 1.3.6.1.4.1.562.36.2.1.71.101.666.1
An entry in the mscFrUniCaIngCirBPTable.
OBJECT-TYPE    
  MscFrUniCaIngCirBPEntry  

mscFrUniCaIngCirBPIndex 1.3.6.1.4.1.562.36.2.1.71.101.666.1.1
This variable represents the mscFrUniCaIngCirBPTable specific index for the mscFrUniCaIngCirBPTable.
OBJECT-TYPE    
  Integer32 0..15  

mscFrUniCaIngCirBPValue 1.3.6.1.4.1.562.36.2.1.71.101.666.1.2
This variable represents an individual value for the mscFrUniCaIngCirBPTable.
OBJECT-TYPE    
  Unsigned32 0..1000  

mscFrUniCaEgCirBpTable 1.3.6.1.4.1.562.36.2.1.71.101.667
Port capacity is partitioned into 16 pools (pool 0 through pool 15) for the egress CIR traffic. This attribute specifies the percentage of port capacity that is allowed for each pool. The percentage for each pool ranges from 0% to 1000% of the link rate. It allows for under or over subscription of the port. Under subscription occurs when the sum of the percentages assigned to the 16 pools is less than 100%. Over subscription occurs when the sum of the percentages for the 16 pools exceeds 100%. The default is full sharing of port capacity with three pre-set partitions.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaEgCirBpEntry

mscFrUniCaEgCirBpEntry 1.3.6.1.4.1.562.36.2.1.71.101.667.1
An entry in the mscFrUniCaEgCirBpTable.
OBJECT-TYPE    
  MscFrUniCaEgCirBpEntry  

mscFrUniCaEgCirBpIndex 1.3.6.1.4.1.562.36.2.1.71.101.667.1.1
This variable represents the mscFrUniCaEgCirBpTable specific index for the mscFrUniCaEgCirBpTable.
OBJECT-TYPE    
  Integer32 0..15  

mscFrUniCaEgCirBpValue 1.3.6.1.4.1.562.36.2.1.71.101.667.1.2
This variable represents an individual value for the mscFrUniCaEgCirBpTable.
OBJECT-TYPE    
  Unsigned32 0..1000  

mscFrUniCaIngCirPoolAdmitBwTable 1.3.6.1.4.1.562.36.2.1.71.101.668
This attribute indicates the total admitted CIR bandwidth from each CIR bandwidth pool in the ingress direction. Each value is the sum of the equivalent bit rates of the admitted connections.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaIngCirPoolAdmitBwEntry

mscFrUniCaIngCirPoolAdmitBwEntry 1.3.6.1.4.1.562.36.2.1.71.101.668.1
An entry in the mscFrUniCaIngCirPoolAdmitBwTable.
OBJECT-TYPE    
  MscFrUniCaIngCirPoolAdmitBwEntry  

mscFrUniCaIngCirPoolAdmitBwIndex 1.3.6.1.4.1.562.36.2.1.71.101.668.1.1
This variable represents the mscFrUniCaIngCirPoolAdmitBwTable specific index for the mscFrUniCaIngCirPoolAdmitBwTable.
OBJECT-TYPE    
  Integer32 0..15  

mscFrUniCaIngCirPoolAdmitBwValue 1.3.6.1.4.1.562.36.2.1.71.101.668.1.2
This variable represents an individual value for the mscFrUniCaIngCirPoolAdmitBwTable.
OBJECT-TYPE    
  Gauge32 0..520000000  

mscFrUniCaIngCirPoolAvailBwTable 1.3.6.1.4.1.562.36.2.1.71.101.669
This attribute indicates the remaining available CIR bandwidth in each ingress CIR bandwidth pool.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaIngCirPoolAvailBwEntry

mscFrUniCaIngCirPoolAvailBwEntry 1.3.6.1.4.1.562.36.2.1.71.101.669.1
An entry in the mscFrUniCaIngCirPoolAvailBwTable.
OBJECT-TYPE    
  MscFrUniCaIngCirPoolAvailBwEntry  

mscFrUniCaIngCirPoolAvailBwIndex 1.3.6.1.4.1.562.36.2.1.71.101.669.1.1
This variable represents the mscFrUniCaIngCirPoolAvailBwTable specific index for the mscFrUniCaIngCirPoolAvailBwTable.
OBJECT-TYPE    
  Integer32 0..15  

mscFrUniCaIngCirPoolAvailBwValue 1.3.6.1.4.1.562.36.2.1.71.101.669.1.2
This variable represents an individual value for the mscFrUniCaIngCirPoolAvailBwTable.
OBJECT-TYPE    
  Gauge32 0..52000000  

mscFrUniCaEgCirPoolAdmitBwTable 1.3.6.1.4.1.562.36.2.1.71.101.670
This attribute indicates the total admitted CIR bandwidth from each CIR bandwidth pool in the egress direction. Each value is the sum of the equivalent bit rates of the admitted connections.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaEgCirPoolAdmitBwEntry

mscFrUniCaEgCirPoolAdmitBwEntry 1.3.6.1.4.1.562.36.2.1.71.101.670.1
An entry in the mscFrUniCaEgCirPoolAdmitBwTable.
OBJECT-TYPE    
  MscFrUniCaEgCirPoolAdmitBwEntry  

mscFrUniCaEgCirPoolAdmitBwIndex 1.3.6.1.4.1.562.36.2.1.71.101.670.1.1
This variable represents the mscFrUniCaEgCirPoolAdmitBwTable specific index for the mscFrUniCaEgCirPoolAdmitBwTable.
OBJECT-TYPE    
  Integer32 0..15  

mscFrUniCaEgCirPoolAdmitBwValue 1.3.6.1.4.1.562.36.2.1.71.101.670.1.2
This variable represents an individual value for the mscFrUniCaEgCirPoolAdmitBwTable.
OBJECT-TYPE    
  Gauge32 0..520000000  

mscFrUniCaEgCirPoolAvailBwTable 1.3.6.1.4.1.562.36.2.1.71.101.671
This attribute indicates the remaining available CIR bandwidth in each egress CIR bandwidth pool.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaEgCirPoolAvailBwEntry

mscFrUniCaEgCirPoolAvailBwEntry 1.3.6.1.4.1.562.36.2.1.71.101.671.1
An entry in the mscFrUniCaEgCirPoolAvailBwTable.
OBJECT-TYPE    
  MscFrUniCaEgCirPoolAvailBwEntry  

mscFrUniCaEgCirPoolAvailBwIndex 1.3.6.1.4.1.562.36.2.1.71.101.671.1.1
This variable represents the mscFrUniCaEgCirPoolAvailBwTable specific index for the mscFrUniCaEgCirPoolAvailBwTable.
OBJECT-TYPE    
  Integer32 0..15  

mscFrUniCaEgCirPoolAvailBwValue 1.3.6.1.4.1.562.36.2.1.71.101.671.1.2
This variable represents an individual value for the mscFrUniCaEgCirPoolAvailBwTable.
OBJECT-TYPE    
  Gauge32 0..52000000  

mscFrUniCaIngEirBpTable 1.3.6.1.4.1.562.36.2.1.71.101.673
Port capacity is partitioned into 16 pools (pool 0 through pool 15) for the ingress EIR traffic. This attribute specifies the percentage of port capacity that is allowed for each pool. The percentage for each pool ranges from 0% to 1000% of the link rate. It allows for under or over subscription of the port. Under subscription occurs when the sum of the percentages assigned to the 16 pools is less than 100%. Over subscription occurs when the sum of the percentages for the 16 pools exceeds 100%. The default is full sharing of port capacity with three pre-set partitions.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaIngEirBpEntry

mscFrUniCaIngEirBpEntry 1.3.6.1.4.1.562.36.2.1.71.101.673.1
An entry in the mscFrUniCaIngEirBpTable.
OBJECT-TYPE    
  MscFrUniCaIngEirBpEntry  

mscFrUniCaIngEirBpIndex 1.3.6.1.4.1.562.36.2.1.71.101.673.1.1
This variable represents the mscFrUniCaIngEirBpTable specific index for the mscFrUniCaIngEirBpTable.
OBJECT-TYPE    
  Integer32 0..15  

mscFrUniCaIngEirBpValue 1.3.6.1.4.1.562.36.2.1.71.101.673.1.2
This variable represents an individual value for the mscFrUniCaIngEirBpTable.
OBJECT-TYPE    
  Unsigned32 0..1000  

mscFrUniCaEgEirBpTable 1.3.6.1.4.1.562.36.2.1.71.101.674
Port capacity is partitioned into 16 pools (pool 0 through pool 15) for the egress EIR traffic. This attribute specifies the percentage of port capacity that is allowed for each pool. The percentage for each pool ranges from 0% to 1000% of the link rate. It allows for under or over subscription of the port. Under subscription occurs when the sum of the percentages assigned to the 16 pools is less than 100%. Over subscription occurs when the sum of the percentages for the 16 pools exceeds 100%. The default is full sharing of port capacity with three pre-set partitions.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaEgEirBpEntry

mscFrUniCaEgEirBpEntry 1.3.6.1.4.1.562.36.2.1.71.101.674.1
An entry in the mscFrUniCaEgEirBpTable.
OBJECT-TYPE    
  MscFrUniCaEgEirBpEntry  

mscFrUniCaEgEirBpIndex 1.3.6.1.4.1.562.36.2.1.71.101.674.1.1
This variable represents the mscFrUniCaEgEirBpTable specific index for the mscFrUniCaEgEirBpTable.
OBJECT-TYPE    
  Integer32 0..15  

mscFrUniCaEgEirBpValue 1.3.6.1.4.1.562.36.2.1.71.101.674.1.2
This variable represents an individual value for the mscFrUniCaEgEirBpTable.
OBJECT-TYPE    
  Unsigned32 0..1000  

mscFrUniCaIngEirPoolAdmitBwTable 1.3.6.1.4.1.562.36.2.1.71.101.675
This attribute indicates the total admitted EIR bandwidth from each EIR bandwidth pool in the ingress direction. Each value is the sum of the equivalent bit rates of the admitted connections. If the ingressApplyToCos attribute is set to none, all ingress CIR bandwidth pools are set to 0.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaIngEirPoolAdmitBwEntry

mscFrUniCaIngEirPoolAdmitBwEntry 1.3.6.1.4.1.562.36.2.1.71.101.675.1
An entry in the mscFrUniCaIngEirPoolAdmitBwTable.
OBJECT-TYPE    
  MscFrUniCaIngEirPoolAdmitBwEntry  

mscFrUniCaIngEirPoolAdmitBwIndex 1.3.6.1.4.1.562.36.2.1.71.101.675.1.1
This variable represents the mscFrUniCaIngEirPoolAdmitBwTable specific index for the mscFrUniCaIngEirPoolAdmitBwTable.
OBJECT-TYPE    
  Integer32 0..15  

mscFrUniCaIngEirPoolAdmitBwValue 1.3.6.1.4.1.562.36.2.1.71.101.675.1.2
This variable represents an individual value for the mscFrUniCaIngEirPoolAdmitBwTable.
OBJECT-TYPE    
  Gauge32 0..520000000  

mscFrUniCaIngEirPoolAvailBwTable 1.3.6.1.4.1.562.36.2.1.71.101.676
This attribute indicates the remaining available EIR bandwidth in each ingress EIR bandwidth pool. If the ingressApplyToCos attribute is set to either none or cirOnly, all ingress EIR bandwidth pools are set to 0.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaIngEirPoolAvailBwEntry

mscFrUniCaIngEirPoolAvailBwEntry 1.3.6.1.4.1.562.36.2.1.71.101.676.1
An entry in the mscFrUniCaIngEirPoolAvailBwTable.
OBJECT-TYPE    
  MscFrUniCaIngEirPoolAvailBwEntry  

mscFrUniCaIngEirPoolAvailBwIndex 1.3.6.1.4.1.562.36.2.1.71.101.676.1.1
This variable represents the mscFrUniCaIngEirPoolAvailBwTable specific index for the mscFrUniCaIngEirPoolAvailBwTable.
OBJECT-TYPE    
  Integer32 0..15  

mscFrUniCaIngEirPoolAvailBwValue 1.3.6.1.4.1.562.36.2.1.71.101.676.1.2
This variable represents an individual value for the mscFrUniCaIngEirPoolAvailBwTable.
OBJECT-TYPE    
  Gauge32 0..52000000  

mscFrUniCaEgEirPoolAdmitBwTable 1.3.6.1.4.1.562.36.2.1.71.101.677
This attribute indicates the total admitted EIR bandwidth from each EIR bandwidth pool in the egress direction. Each value is the sum of the equivalent bit rates of the admitted connections. If the egressApplyToCos attribute is set to none, all egress CIR bandwidth pools are set to 0.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaEgEirPoolAdmitBwEntry

mscFrUniCaEgEirPoolAdmitBwEntry 1.3.6.1.4.1.562.36.2.1.71.101.677.1
An entry in the mscFrUniCaEgEirPoolAdmitBwTable.
OBJECT-TYPE    
  MscFrUniCaEgEirPoolAdmitBwEntry  

mscFrUniCaEgEirPoolAdmitBwIndex 1.3.6.1.4.1.562.36.2.1.71.101.677.1.1
This variable represents the mscFrUniCaEgEirPoolAdmitBwTable specific index for the mscFrUniCaEgEirPoolAdmitBwTable.
OBJECT-TYPE    
  Integer32 0..15  

mscFrUniCaEgEirPoolAdmitBwValue 1.3.6.1.4.1.562.36.2.1.71.101.677.1.2
This variable represents an individual value for the mscFrUniCaEgEirPoolAdmitBwTable.
OBJECT-TYPE    
  Gauge32 0..520000000  

mscFrUniCaEgEirPoolAvailBwTable 1.3.6.1.4.1.562.36.2.1.71.101.678
This attribute indicates the remaining available EIR bandwidth in each egress EIR bandwidth pool. If the egressApplyToCos attribute is set to either none or cirOnly, all egress EIR bandwidth pools are set to 0.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniCaEgEirPoolAvailBwEntry

mscFrUniCaEgEirPoolAvailBwEntry 1.3.6.1.4.1.562.36.2.1.71.101.678.1
An entry in the mscFrUniCaEgEirPoolAvailBwTable.
OBJECT-TYPE    
  MscFrUniCaEgEirPoolAvailBwEntry  

mscFrUniCaEgEirPoolAvailBwIndex 1.3.6.1.4.1.562.36.2.1.71.101.678.1.1
This variable represents the mscFrUniCaEgEirPoolAvailBwTable specific index for the mscFrUniCaEgEirPoolAvailBwTable.
OBJECT-TYPE    
  Integer32 0..15  

mscFrUniCaEgEirPoolAvailBwValue 1.3.6.1.4.1.562.36.2.1.71.101.678.1.2
This variable represents an individual value for the mscFrUniCaEgEirPoolAvailBwTable.
OBJECT-TYPE    
  Gauge32 0..52000000  

mscFrUniFrmToIfByQueueTable 1.3.6.1.4.1.562.36.2.1.71.341
This attribute counts the total number of frames transmitted to the interface per egress emission priority queue since the component has been activated. There is potientially a maximum of 4 emission priority queues. The number of available egress queues varies according to the value of the provisionable attribute numberOfEmissionQs. Egress queue 0 has the lowest priority, while egress queue 3 has the highest priority. The queue values are only indicated when the numberOfEmissionQs is set to 4 queues.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniFrmToIfByQueueEntry

mscFrUniFrmToIfByQueueEntry 1.3.6.1.4.1.562.36.2.1.71.341.1
An entry in the mscFrUniFrmToIfByQueueTable.
OBJECT-TYPE    
  MscFrUniFrmToIfByQueueEntry  

mscFrUniFrmToIfByQueueIndex 1.3.6.1.4.1.562.36.2.1.71.341.1.1
This variable represents the index for the mscFrUniFrmToIfByQueueTable.
OBJECT-TYPE    
  Integer32 0..3  

mscFrUniFrmToIfByQueueValue 1.3.6.1.4.1.562.36.2.1.71.341.1.2
This variable represents an individual value for the mscFrUniFrmToIfByQueueTable.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscFrUniOctetToIfByQueueTable 1.3.6.1.4.1.562.36.2.1.71.342
This attribute counts the total number of octets transmitted from the service to the interface per emission priority queue since the component has been activated. There is potientially a maximum of 4 emission priority queues. The number of available egress queues varies according to the value of the provisionable attribute numberOfEmissionQs. Egress queue 0 has the lowest priority, while egress queue 3 has the highest priority.
OBJECT-TYPE    
  SEQUENCE OF  
    MscFrUniOctetToIfByQueueEntry

mscFrUniOctetToIfByQueueEntry 1.3.6.1.4.1.562.36.2.1.71.342.1
An entry in the mscFrUniOctetToIfByQueueTable.
OBJECT-TYPE    
  MscFrUniOctetToIfByQueueEntry  

mscFrUniOctetToIfByQueueIndex 1.3.6.1.4.1.562.36.2.1.71.342.1.1
This variable represents the index for the mscFrUniOctetToIfByQueueTable.
OBJECT-TYPE    
  Integer32 0..3  

mscFrUniOctetToIfByQueueValue 1.3.6.1.4.1.562.36.2.1.71.342.1.2
This variable represents an individual value for the mscFrUniOctetToIfByQueueTable.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

frameRelayUniMIB 1.3.6.1.4.1.562.36.2.2.24
OBJECT IDENTIFIER    

frameRelayUniGroup 1.3.6.1.4.1.562.36.2.2.24.1
OBJECT IDENTIFIER    

frameRelayUniGroupCA 1.3.6.1.4.1.562.36.2.2.24.1.1
OBJECT IDENTIFIER    

frameRelayUniGroupCA02 1.3.6.1.4.1.562.36.2.2.24.1.1.3
OBJECT IDENTIFIER    

frameRelayUniGroupCA02A 1.3.6.1.4.1.562.36.2.2.24.1.1.3.2
OBJECT IDENTIFIER    

frameRelayUniCapabilities 1.3.6.1.4.1.562.36.2.2.24.3
OBJECT IDENTIFIER    

frameRelayUniCapabilitiesCA 1.3.6.1.4.1.562.36.2.2.24.3.1
OBJECT IDENTIFIER    

frameRelayUniCapabilitiesCA02 1.3.6.1.4.1.562.36.2.2.24.3.1.3
OBJECT IDENTIFIER    

frameRelayUniCapabilitiesCA02A 1.3.6.1.4.1.562.36.2.2.24.3.1.3.2
OBJECT IDENTIFIER    

Defined Objects

MscFrUniRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniRowStatus  
  DisplayString as mscFrUniComponentName  
  StorageType as mscFrUniStorageType  
  Integer32 as mscFrUniIndex  

MscFrUniCidDataEntry  
SEQUENCE    
  Unsigned32 as mscFrUniCustomerIdentifier  

MscFrUniStateEntry  
SEQUENCE    
  INTEGER as mscFrUniAdminState  
  INTEGER as mscFrUniOperationalState  
  INTEGER as mscFrUniUsageState  
  OCTET STRING as mscFrUniAvailabilityStatus  
  OCTET STRING as mscFrUniProceduralStatus  
  OCTET STRING as mscFrUniControlStatus  
  OCTET STRING as mscFrUniAlarmStatus  
  INTEGER as mscFrUniStandbyStatus  
  INTEGER as mscFrUniUnknownStatus  

MscFrUniStatsEntry  
SEQUENCE    
  Unsigned32 as mscFrUniLastUnknownDlci  
  Counter32 as mscFrUniUnknownDlciFramesFromIf  
  Counter32 as mscFrUniInvalidHeaderFramesFromIf  

MscFrUniIfEntryEntry  
SEQUENCE    
  INTEGER as mscFrUniIfAdminStatus  
  InterfaceIndex as mscFrUniIfIndex  

MscFrUniOperStatusEntry  
SEQUENCE    
  INTEGER as mscFrUniSnmpOperStatus  

MscFrUniEmissionPriorityQsEntry  
SEQUENCE    
  Unsigned32 as mscFrUniNumberOfEmissionQs  

MscFrUniFrmToIfByQueueEntry  
SEQUENCE    
  Integer32 as mscFrUniFrmToIfByQueueIndex  
  Unsigned32 as mscFrUniFrmToIfByQueueValue  

MscFrUniOctetToIfByQueueEntry  
SEQUENCE    
  Integer32 as mscFrUniOctetToIfByQueueIndex  
  Unsigned32 as mscFrUniOctetToIfByQueueValue  

MscFrUniDnaRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniDnaRowStatus  
  DisplayString as mscFrUniDnaComponentName  
  StorageType as mscFrUniDnaStorageType  
  NonReplicated as mscFrUniDnaIndex  

MscFrUniDnaAddressEntry  
SEQUENCE    
  INTEGER as mscFrUniDnaNumberingPlanIndicator  
  DigitString as mscFrUniDnaDataNetworkAddress  

MscFrUniDnaOutgoingOptionsEntry  
SEQUENCE    
  INTEGER as mscFrUniDnaOutDefaultPriority  
  INTEGER as mscFrUniDnaOutDefaultPathSensitivity  
  INTEGER as mscFrUniDnaOutPathSensitivityOverRide  
  INTEGER as mscFrUniDnaOutDefaultPathReliability  
  INTEGER as mscFrUniDnaOutAccess  
  INTEGER as mscFrUniDnaDefaultTransferPriority  
  INTEGER as mscFrUniDnaTransferPriorityOverRide  

MscFrUniDnaIncomingOptionsEntry  
SEQUENCE    
  INTEGER as mscFrUniDnaIncAccess  

MscFrUniDnaCallOptionsEntry  
SEQUENCE    
  Unsigned32 as mscFrUniDnaAccountClass  
  OCTET STRING as mscFrUniDnaAccountCollection  
  Unsigned32 as mscFrUniDnaServiceExchange  
  INTEGER as mscFrUniDnaEgressAccounting  
  INTEGER as mscFrUniDnaDataPath  

MscFrUniDnaCugRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniDnaCugRowStatus  
  DisplayString as mscFrUniDnaCugComponentName  
  StorageType as mscFrUniDnaCugStorageType  
  Integer32 as mscFrUniDnaCugIndex  

MscFrUniDnaCugCugOptionsEntry  
SEQUENCE    
  INTEGER as mscFrUniDnaCugType  
  DigitString as mscFrUniDnaCugDnic  
  Unsigned32 as mscFrUniDnaCugInterlockCode  
  INTEGER as mscFrUniDnaCugPreferential  
  INTEGER as mscFrUniDnaCugOutCalls  
  INTEGER as mscFrUniDnaCugIncCalls  

MscFrUniDnaHgMRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniDnaHgMRowStatus  
  DisplayString as mscFrUniDnaHgMComponentName  
  StorageType as mscFrUniDnaHgMStorageType  
  NonReplicated as mscFrUniDnaHgMIndex  

MscFrUniDnaHgMIfEntry  
SEQUENCE    
  Unsigned32 as mscFrUniDnaHgMAvailabilityUpdateThreshold  

MscFrUniDnaHgMOpEntry  
SEQUENCE    
  Unsigned32 as mscFrUniDnaHgMMaximumAvailableAggregateCir  
  Unsigned32 as mscFrUniDnaHgMAvailableAggregateCir  
  INTEGER as mscFrUniDnaHgMAvailabilityDelta  
  Unsigned32 as mscFrUniDnaHgMAvailableDlcis  

MscFrUniDnaHgMHgAddrRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniDnaHgMHgAddrRowStatus  
  DisplayString as mscFrUniDnaHgMHgAddrComponentName  
  StorageType as mscFrUniDnaHgMHgAddrStorageType  
  Integer32 as mscFrUniDnaHgMHgAddrIndex  

MscFrUniDnaHgMHgAddrAddrEntry  
SEQUENCE    
  INTEGER as mscFrUniDnaHgMHgAddrNumberingPlanIndicator  
  DigitString as mscFrUniDnaHgMHgAddrDataNetworkAddress  

MscFrUniFramerRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniFramerRowStatus  
  DisplayString as mscFrUniFramerComponentName  
  StorageType as mscFrUniFramerStorageType  
  NonReplicated as mscFrUniFramerIndex  

MscFrUniFramerProvEntry  
SEQUENCE    
  Link as mscFrUniFramerInterfaceName  

MscFrUniFramerLinkEntry  
SEQUENCE    
  INTEGER as mscFrUniFramerDataInversion  
  INTEGER as mscFrUniFramerFrameCrcType  
  Unsigned32 as mscFrUniFramerFlagsBetweenFrames  

MscFrUniFramerStateEntry  
SEQUENCE    
  INTEGER as mscFrUniFramerAdminState  
  INTEGER as mscFrUniFramerOperationalState  
  INTEGER as mscFrUniFramerUsageState  

MscFrUniFramerStatsEntry  
SEQUENCE    
  Counter32 as mscFrUniFramerFrmToIf  
  Counter32 as mscFrUniFramerFrmFromIf  
  Counter32 as mscFrUniFramerOctetFromIf  
  Counter32 as mscFrUniFramerAborts  
  Counter32 as mscFrUniFramerCrcErrors  
  Counter32 as mscFrUniFramerLrcErrors  
  Counter32 as mscFrUniFramerNonOctetErrors  
  Counter32 as mscFrUniFramerOverruns  
  Counter32 as mscFrUniFramerUnderruns  
  Counter32 as mscFrUniFramerLargeFrmErrors  
  Counter32 as mscFrUniFramerFrmModeErrors  
  PassportCounter64 as mscFrUniFramerFrmToIf64  
  PassportCounter64 as mscFrUniFramerFrmFromIf64  
  PassportCounter64 as mscFrUniFramerOctetFromIf64  

MscFrUniFramerUtilEntry  
SEQUENCE    
  Gauge32 as mscFrUniFramerNormPrioLinkUtilToIf  
  Gauge32 as mscFrUniFramerNormPrioLinkUtilFromIf  

MscFrUniLmiRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniLmiRowStatus  
  DisplayString as mscFrUniLmiComponentName  
  StorageType as mscFrUniLmiStorageType  
  NonReplicated as mscFrUniLmiIndex  

MscFrUniLmiParmsEntry  
SEQUENCE    
  INTEGER as mscFrUniLmiProcedures  
  INTEGER as mscFrUniLmiAsyncStatusReport  
  Unsigned32 as mscFrUniLmiErrorEventThreshold  
  Unsigned32 as mscFrUniLmiEventCount  
  Unsigned32 as mscFrUniLmiCheckPointTimer  
  Unsigned32 as mscFrUniLmiMessageCountTimer  
  INTEGER as mscFrUniLmiIgnoreActiveBit  
  INTEGER as mscFrUniLmiSide  
  INTEGER as mscFrUniLmiPvcConfigParmsInFsr  

MscFrUniLmiStateEntry  
SEQUENCE    
  INTEGER as mscFrUniLmiAdminState  
  INTEGER as mscFrUniLmiOperationalState  
  INTEGER as mscFrUniLmiUsageState  

MscFrUniLmiPsiEntry  
SEQUENCE    
  INTEGER as mscFrUniLmiProtocolStatus  
  INTEGER as mscFrUniLmiOpProcedures  

MscFrUniLmiStatsEntry  
SEQUENCE    
  Counter32 as mscFrUniLmiKeepAliveStatusToIf  
  Counter32 as mscFrUniLmiFullStatusToIf  
  Counter32 as mscFrUniLmiKeepAliveStatusEnqFromIf  
  Counter32 as mscFrUniLmiFullStatusEnqFromIf  
  AsciiString as mscFrUniLmiNetworkSideEventHistory  
  Counter32 as mscFrUniLmiProtocolErrors  
  Counter32 as mscFrUniLmiUnexpectedIes  
  Counter32 as mscFrUniLmiSequenceErrors  
  Counter32 as mscFrUniLmiUnexpectedReports  
  Counter32 as mscFrUniLmiPollingVerifTimeouts  
  Counter32 as mscFrUniLmiKeepAliveEnqToIf  
  Counter32 as mscFrUniLmiFullStatusEnqToIf  
  AsciiString as mscFrUniLmiUserSideEventHistory  
  Counter32 as mscFrUniLmiStatusSequenceErrors  
  Counter32 as mscFrUniLmiNoStatusReportCount  

MscFrUniLmiUspParmsEntry  
SEQUENCE    
  Unsigned32 as mscFrUniLmiFullStatusPollingCycles  
  Unsigned32 as mscFrUniLmiLinkVerificationTimer  

MscFrUniDlciRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniDlciRowStatus  
  DisplayString as mscFrUniDlciComponentName  
  StorageType as mscFrUniDlciStorageType  
  Integer32 as mscFrUniDlciIndex  

MscFrUniDlciStateEntry  
SEQUENCE    
  INTEGER as mscFrUniDlciAdminState  
  INTEGER as mscFrUniDlciOperationalState  
  INTEGER as mscFrUniDlciUsageState  
  OCTET STRING as mscFrUniDlciAvailabilityStatus  
  OCTET STRING as mscFrUniDlciProceduralStatus  
  OCTET STRING as mscFrUniDlciControlStatus  
  OCTET STRING as mscFrUniDlciAlarmStatus  
  INTEGER as mscFrUniDlciStandbyStatus  
  INTEGER as mscFrUniDlciUnknownStatus  

MscFrUniDlciAbitEntry  
SEQUENCE    
  INTEGER as mscFrUniDlciABitStatusToIf  
  INTEGER as mscFrUniDlciABitReasonToIf  
  INTEGER as mscFrUniDlciABitStatusFromIf  
  INTEGER as mscFrUniDlciABitReasonFromIf  
  INTEGER as mscFrUniDlciLoopbackState  

MscFrUniDlciCalldEntry  
SEQUENCE    
  INTEGER as mscFrUniDlciCallType  
  INTEGER as mscFrUniDlciQstate  
  Unsigned32 as mscFrUniDlciCallref  

MscFrUniDlciSpOpEntry  
SEQUENCE    
  Unsigned32 as mscFrUniDlciMaximumFrameSize  
  INTEGER as mscFrUniDlciRateEnforcement  
  Unsigned32 as mscFrUniDlciCommittedInformationRate  
  Unsigned32 as mscFrUniDlciCommittedBurstSize  
  Unsigned32 as mscFrUniDlciExcessBurstSize  
  Unsigned32 as mscFrUniDlciMeasurementInterval  
  INTEGER as mscFrUniDlciRateAdaptation  
  INTEGER as mscFrUniDlciAccounting  
  INTEGER as mscFrUniDlciEmissionPriorityToIf  
  Unsigned32 as mscFrUniDlciTransferPriToNwk  
  Unsigned32 as mscFrUniDlciTransferPriFromNwk  

MscFrUniDlciStatsEntry  
SEQUENCE    
  Unsigned32 as mscFrUniDlciFrmToIf  
  Unsigned32 as mscFrUniDlciFecnFrmToIf  
  Unsigned32 as mscFrUniDlciBecnFrmToIf  
  Unsigned32 as mscFrUniDlciBciToSubnet  
  Unsigned32 as mscFrUniDlciDeFrmToIf  
  Unsigned32 as mscFrUniDlciDiscCongestedToIf  
  Unsigned32 as mscFrUniDlciDiscDeCongestedToIf  
  Unsigned32 as mscFrUniDlciFrmFromIf  
  Unsigned32 as mscFrUniDlciFecnFrmFromIf  
  Unsigned32 as mscFrUniDlciBecnFrmFromIf  
  Unsigned32 as mscFrUniDlciFciFromSubnet  
  Unsigned32 as mscFrUniDlciBciFromSubnet  
  Unsigned32 as mscFrUniDlciDeFrmFromIf  
  Unsigned32 as mscFrUniDlciExcessFrmFromIf  
  Unsigned32 as mscFrUniDlciDiscExcessFromIf  
  Unsigned32 as mscFrUniDlciDiscFrameAbit  
  Unsigned32 as mscFrUniDlciDiscCongestedFromIf  
  Unsigned32 as mscFrUniDlciDiscDeCongestedFromIf  
  Unsigned32 as mscFrUniDlciErrorShortFrmFromIf  
  Unsigned32 as mscFrUniDlciErrorLongFrmFromIf  
  Unsigned32 as mscFrUniDlciBecnFrmSetByService  
  Unsigned32 as mscFrUniDlciBytesToIf  
  Unsigned32 as mscFrUniDlciDeBytesToIf  
  Unsigned32 as mscFrUniDlciDiscCongestedToIfBytes  
  Unsigned32 as mscFrUniDlciDiscDeCongestedToIfBytes  
  Unsigned32 as mscFrUniDlciBytesFromIf  
  Unsigned32 as mscFrUniDlciDeBytesFromIf  
  Unsigned32 as mscFrUniDlciExcessBytesFromIf  
  Unsigned32 as mscFrUniDlciDiscExcessFromIfBytes  
  Unsigned32 as mscFrUniDlciDiscByteAbit  
  Unsigned32 as mscFrUniDlciDiscCongestedFromIfBytes  
  Unsigned32 as mscFrUniDlciDiscDeCongestedFromIfBytes  
  Unsigned32 as mscFrUniDlciErrorShortBytesFromIf  
  Unsigned32 as mscFrUniDlciErrorLongBytesFromIf  
  Unsigned32 as mscFrUniDlciRateAdaptReduct  
  Unsigned32 as mscFrUniDlciRateAdaptReductPeriod  
  INTEGER as mscFrUniDlciTransferPriorityToNetwork  
  INTEGER as mscFrUniDlciTransferPriorityFromNetwork  
  Unsigned32 as mscFrUniDlciCirPresent  
  Unsigned32 as mscFrUniDlciEirPresent  

MscFrUniDlciIntEntry  
SEQUENCE    
  EnterpriseDateAndTime as mscFrUniDlciStartTime  
  Unsigned64 as mscFrUniDlciTotalIngressBytes  
  Unsigned64 as mscFrUniDlciTotalEgressBytes  
  Unsigned64 as mscFrUniDlciEirIngressBytes  
  Unsigned64 as mscFrUniDlciEirEgressBytes  
  Unsigned64 as mscFrUniDlciDiscardedBytes  
  Unsigned32 as mscFrUniDlciTotalIngressSegFrm  
  Unsigned32 as mscFrUniDlciTotalEgressSegFrm  
  Unsigned32 as mscFrUniDlciEirIngressSegFrm  
  Unsigned32 as mscFrUniDlciEirEgressSegFrm  
  Unsigned32 as mscFrUniDlciDiscardedSegFrm  
  Unsigned32 as mscFrUniDlciCirPresentObs  
  Unsigned32 as mscFrUniDlciEirPresentObs  
  INTEGER as mscFrUniDlciRateEnforcementPresent  
  INTEGER as mscFrUniDlciRateAdaptationPresent  
  INTEGER as mscFrUniDlciLocalRateAdaptOccurred  
  Hex as mscFrUniDlciCallReferenceNumber  
  Unsigned32 as mscFrUniDlciElapsedDifference  
  Unsigned32 as mscFrUniDlciCallRefNumber  

MscFrUniDlciDcRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniDlciDcRowStatus  
  DisplayString as mscFrUniDlciDcComponentName  
  StorageType as mscFrUniDlciDcStorageType  
  NonReplicated as mscFrUniDlciDcIndex  

MscFrUniDlciDcOptionsEntry  
SEQUENCE    
  INTEGER as mscFrUniDlciDcRemoteNpi  
  DigitString as mscFrUniDlciDcRemoteDna  
  Unsigned32 as mscFrUniDlciDcRemoteDlci  
  INTEGER as mscFrUniDlciDcType  
  INTEGER as mscFrUniDlciDcTransferPriority  
  INTEGER as mscFrUniDlciDcDiscardPriority  
  INTEGER as mscFrUniDlciDcDeDiscardPriority  
  INTEGER as mscFrUniDlciDcDataPath  
  Unsigned32 as mscFrUniDlciDcCugIndex  
  INTEGER as mscFrUniDlciDcCugType  
  INTEGER as mscFrUniDlciDcMapIpCosToFrQos  

MscFrUniDlciDcNfaEntry  
SEQUENCE    
  Integer32 as mscFrUniDlciDcNfaIndex  
  HexString as mscFrUniDlciDcNfaValue  
  RowStatus as mscFrUniDlciDcNfaRowStatus  

MscFrUniDlciVcRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniDlciVcRowStatus  
  DisplayString as mscFrUniDlciVcComponentName  
  StorageType as mscFrUniDlciVcStorageType  
  NonReplicated as mscFrUniDlciVcIndex  

MscFrUniDlciVcCadEntry  
SEQUENCE    
  INTEGER as mscFrUniDlciVcType  
  INTEGER as mscFrUniDlciVcState  
  INTEGER as mscFrUniDlciVcPreviousState  
  Unsigned32 as mscFrUniDlciVcDiagnosticCode  
  Unsigned32 as mscFrUniDlciVcPreviousDiagnosticCode  
  INTEGER as mscFrUniDlciVcCalledNpi  
  DigitString as mscFrUniDlciVcCalledDna  
  Unsigned32 as mscFrUniDlciVcCalledLcn  
  INTEGER as mscFrUniDlciVcCallingNpi  
  DigitString as mscFrUniDlciVcCallingDna  
  Unsigned32 as mscFrUniDlciVcCallingLcn  
  INTEGER as mscFrUniDlciVcAccountingEnabled  
  INTEGER as mscFrUniDlciVcFastSelectCall  
  INTEGER as mscFrUniDlciVcPathReliability  
  INTEGER as mscFrUniDlciVcAccountingEnd  
  INTEGER as mscFrUniDlciVcPriority  
  Unsigned32 as mscFrUniDlciVcSegmentSize  
  Unsigned32 as mscFrUniDlciVcMaxSubnetPktSize  
  INTEGER as mscFrUniDlciVcRcosToNetwork  
  INTEGER as mscFrUniDlciVcRcosFromNetwork  
  INTEGER as mscFrUniDlciVcEmissionPriorityToNetwork  
  INTEGER as mscFrUniDlciVcEmissionPriorityFromNetwork  
  AsciiString as mscFrUniDlciVcDataPath  

MscFrUniDlciVcIntdEntry  
SEQUENCE    
  Hex as mscFrUniDlciVcCallReferenceNumber  
  Unsigned32 as mscFrUniDlciVcElapsedTimeTillNow  
  Unsigned32 as mscFrUniDlciVcSegmentsRx  
  Unsigned32 as mscFrUniDlciVcSegmentsSent  
  EnterpriseDateAndTime as mscFrUniDlciVcStartTime  
  Unsigned32 as mscFrUniDlciVcCallReferenceNumberDecimal  

MscFrUniDlciVcFrdEntry  
SEQUENCE    
  Unsigned32 as mscFrUniDlciVcFrmCongestedToSubnet  
  Unsigned32 as mscFrUniDlciVcCannotForwardToSubnet  
  Unsigned32 as mscFrUniDlciVcNotDataXferToSubnet  
  Unsigned32 as mscFrUniDlciVcOutOfRangeFrmFromSubnet  
  Unsigned32 as mscFrUniDlciVcCombErrorsFromSubnet  
  Unsigned32 as mscFrUniDlciVcDuplicatesFromSubnet  
  Unsigned32 as mscFrUniDlciVcNotDataXferFromSubnet  
  Unsigned32 as mscFrUniDlciVcFrmLossTimeouts  
  Unsigned32 as mscFrUniDlciVcOoSeqByteCntExceeded  
  Unsigned32 as mscFrUniDlciVcPeakOoSeqPktCount  
  Unsigned32 as mscFrUniDlciVcPeakOoSeqFrmForwarded  
  Unsigned32 as mscFrUniDlciVcSendSequenceNumber  
  Unsigned32 as mscFrUniDlciVcPktRetryTimeouts  
  Unsigned32 as mscFrUniDlciVcPeakRetryQueueSize  
  Unsigned32 as mscFrUniDlciVcSubnetRecoveries  
  Unsigned32 as mscFrUniDlciVcOoSeqPktCntExceeded  
  Unsigned32 as mscFrUniDlciVcPeakOoSeqByteCount  

MscFrUniDlciVcDmepEntry  
SEQUENCE    
  RowPointer as mscFrUniDlciVcDmepValue  

MscFrUniDlciSpRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniDlciSpRowStatus  
  DisplayString as mscFrUniDlciSpComponentName  
  StorageType as mscFrUniDlciSpStorageType  
  NonReplicated as mscFrUniDlciSpIndex  

MscFrUniDlciSpParmsEntry  
SEQUENCE    
  Unsigned32 as mscFrUniDlciSpMaximumFrameSize  
  INTEGER as mscFrUniDlciSpRateEnforcement  
  Gauge32 as mscFrUniDlciSpCommittedInformationRate  
  Gauge32 as mscFrUniDlciSpCommittedBurstSize  
  Gauge32 as mscFrUniDlciSpExcessBurstSize  
  Unsigned32 as mscFrUniDlciSpMeasurementInterval  
  INTEGER as mscFrUniDlciSpRateAdaptation  
  INTEGER as mscFrUniDlciSpAccounting  
  Unsigned32 as mscFrUniDlciSpRaSensitivity  
  INTEGER as mscFrUniDlciSpUpdateBCI  

MscFrUniDlciLbRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniDlciLbRowStatus  
  DisplayString as mscFrUniDlciLbComponentName  
  StorageType as mscFrUniDlciLbStorageType  
  NonReplicated as mscFrUniDlciLbIndex  

MscFrUniDlciLbStatsEntry  
SEQUENCE    
  Unsigned32 as mscFrUniDlciLbLocalTotalFrm  
  Unsigned32 as mscFrUniDlciLbLocalTotalBytes  
  Unsigned32 as mscFrUniDlciLbLocalFecnFrm  
  Unsigned32 as mscFrUniDlciLbLocalBecnFrm  
  Unsigned32 as mscFrUniDlciLbLocalDeFrm  
  Unsigned32 as mscFrUniDlciLbLocalDeBytes  
  Unsigned32 as mscFrUniDlciLbRemoteTotalFrm  
  Unsigned32 as mscFrUniDlciLbRemoteTotalBytes  
  Unsigned32 as mscFrUniDlciLbRemoteFecnFrm  
  Unsigned32 as mscFrUniDlciLbRemoteBecnFrm  
  Unsigned32 as mscFrUniDlciLbRemoteDeFrm  
  Unsigned32 as mscFrUniDlciLbRemoteDeBytes  

MscFrUniDlciEgressSpRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniDlciEgressSpRowStatus  
  DisplayString as mscFrUniDlciEgressSpComponentName  
  StorageType as mscFrUniDlciEgressSpStorageType  
  NonReplicated as mscFrUniDlciEgressSpIndex  

MscFrUniDlciEgressSpProvEntry  
SEQUENCE    
  Unsigned32 as mscFrUniDlciEgressSpCommittedInformationRate  
  Unsigned32 as mscFrUniDlciEgressSpCommittedBurstSize  
  Unsigned32 as mscFrUniDlciEgressSpExcessBurstSize  
  Unsigned32 as mscFrUniDlciEgressSpMeasurementInterval  

MscFrUniSigRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniSigRowStatus  
  DisplayString as mscFrUniSigComponentName  
  StorageType as mscFrUniSigStorageType  
  NonReplicated as mscFrUniSigIndex  

MscFrUniSigRangeEntry  
SEQUENCE    
  Unsigned32 as mscFrUniSigHighestPvcDlci  
  Unsigned32 as mscFrUniSigHighestPermanentDlci  
  Unsigned32 as mscFrUniSigHighestFriPvcDlci  

MscFrUniSigServParmsEntry  
SEQUENCE    
  Unsigned32 as mscFrUniSigMaximumAggregateSvcCir  
  Unsigned32 as mscFrUniSigMaximumAggregateSvcEir  
  Unsigned32 as mscFrUniSigMaximumFrameSize  
  Unsigned32 as mscFrUniSigDefaultMaximumFrameSize  
  Unsigned32 as mscFrUniSigDefaultCommittedInformationRate  
  Unsigned32 as mscFrUniSigDefaultCommittedBurstSize  
  Unsigned32 as mscFrUniSigDefaultExcessBurstSize  
  INTEGER as mscFrUniSigUnlimitedAggregateEir  
  INTEGER as mscFrUniSigRateEnforcement  
  INTEGER as mscFrUniSigRateAdaptation  
  Unsigned32 as mscFrUniSigMaximumAggregateSvcCirNormalQ  
  Unsigned32 as mscFrUniSigMaximumAggregateSvcCirHighQ  
  Unsigned32 as mscFrUniSigMaximumAggregateSvcCirInterruptQ  
  Unsigned32 as mscFrUniSigMaximumAggregateSvcEirNormalQ  
  Unsigned32 as mscFrUniSigMaximumAggregateSvcEirHighQ  
  Unsigned32 as mscFrUniSigMaximumAggregateSvcEirInterruptQ  
  INTEGER as mscFrUniSigX213IeHandling  
  Unsigned32 as mscFrUniSigRaSensitivity  
  INTEGER as mscFrUniSigUpdateBCI  
  INTEGER as mscFrUniSigDefaultLocCheck  

MscFrUniSigSysParmsEntry  
SEQUENCE    
  Unsigned32 as mscFrUniSigCallSetupTimer  
  Unsigned32 as mscFrUniSigDisconnectTimer  
  Unsigned32 as mscFrUniSigReleaseTimer  
  Unsigned32 as mscFrUniSigCallProceedingTimer  
  INTEGER as mscFrUniSigNetworkType  
  Unsigned32 as mscFrUniSigRestartReqTimer  
  Unsigned32 as mscFrUniSigRestartRcvTimer  
  Unsigned32 as mscFrUniSigStatusEnqTimer  

MscFrUniSigLapfSysEntry  
SEQUENCE    
  Unsigned32 as mscFrUniSigWindowSize  
  Unsigned32 as mscFrUniSigRetransmitLimit  
  Unsigned32 as mscFrUniSigAckTimer  
  Unsigned32 as mscFrUniSigAckDelayTimer  
  Unsigned32 as mscFrUniSigIdleProbeTimer  

MscFrUniSigStateEntry  
SEQUENCE    
  INTEGER as mscFrUniSigAdminState  
  INTEGER as mscFrUniSigOperationalState  
  INTEGER as mscFrUniSigUsageState  

MscFrUniSigStatsEntry  
SEQUENCE    
  Gauge32 as mscFrUniSigCurrentNumberOfSvcCalls  
  Gauge32 as mscFrUniSigInCalls  
  Counter32 as mscFrUniSigInCallsRefused  
  Gauge32 as mscFrUniSigOutCalls  
  Counter32 as mscFrUniSigOutCallsFailed  
  Counter32 as mscFrUniSigProtocolErrors  
  Counter32 as mscFrUniSigQualityOfServiceNotAvailable  
  Counter32 as mscFrUniSigSetupTimeout  
  Unsigned32 as mscFrUniSigLastCauseInStatusMsgReceived  
  INTEGER as mscFrUniSigLastStateInStatusMsgReceived  
  Unsigned32 as mscFrUniSigLastDlciReceivedStatus  
  INTEGER as mscFrUniSigLastStateReceivedStatus  
  EnterpriseDateAndTime as mscFrUniSigLastTimeMsgBlockCongested  
  Unsigned32 as mscFrUniSigLastDlciWithMsgBlockCongestion  
  Unsigned32 as mscFrUniSigCurrentAggregateSvcCirNormalQ  
  Unsigned32 as mscFrUniSigCurrentAggregateSvcCirHighQ  
  Unsigned32 as mscFrUniSigCurrentAggregateSvcCirInterruptQ  
  Unsigned32 as mscFrUniSigCurrentAggregateSvcEirNormalQ  
  Unsigned32 as mscFrUniSigCurrentAggregateSvcEirHighQ  
  Unsigned32 as mscFrUniSigCurrentAggregateSvcEirInterruptQ  

MscFrUniSigLapfStatusEntry  
SEQUENCE    
  INTEGER as mscFrUniSigCurrentState  
  INTEGER as mscFrUniSigLastStateChangeReason  
  HexString as mscFrUniSigFrmrReceive  
  Counter32 as mscFrUniSigCurrentQueueSize  

MscFrUniSigLapfStatsEntry  
SEQUENCE    
  Counter32 as mscFrUniSigStateChange  
  Counter32 as mscFrUniSigRemoteBusy  
  Counter32 as mscFrUniSigReceiveRejectFrame  
  Counter32 as mscFrUniSigAckTimeout  
  Counter32 as mscFrUniSigIFramesTransmitted  
  Counter32 as mscFrUniSigIFramesTxDiscarded  
  Counter32 as mscFrUniSigIFramesReceived  
  Counter32 as mscFrUniSigIFramesRcvdDiscarded  

MscFrUniSigSvcaccEntry  
SEQUENCE    
  INTEGER as mscFrUniSigDefaultAccounting  

MscFrUniSigCodesEntry  
SEQUENCE    
  DigitString as mscFrUniSigLastClearRemoteDataNetworkAddress  
  Unsigned32 as mscFrUniSigLastClearCause  
  Unsigned32 as mscFrUniSigLastDiagnosticCode  

MscFrUniSigBandwidthNotAvailableEntry  
SEQUENCE    
  Integer32 as mscFrUniSigBandwidthNotAvailableIndex  
  Counter32 as mscFrUniSigBandwidthNotAvailableValue  

MscFrUniVFramerRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniVFramerRowStatus  
  DisplayString as mscFrUniVFramerComponentName  
  StorageType as mscFrUniVFramerStorageType  
  NonReplicated as mscFrUniVFramerIndex  

MscFrUniVFramerProvEntry  
SEQUENCE    
  Link as mscFrUniVFramerOtherVirtualFramer  
  Link as mscFrUniVFramerLogicalProcessor  

MscFrUniVFramerStateEntry  
SEQUENCE    
  INTEGER as mscFrUniVFramerAdminState  
  INTEGER as mscFrUniVFramerOperationalState  
  INTEGER as mscFrUniVFramerUsageState  

MscFrUniVFramerStatsEntry  
SEQUENCE    
  PassportCounter64 as mscFrUniVFramerFrmToOtherVFramer  
  PassportCounter64 as mscFrUniVFramerFrmFromOtherVFramer  
  PassportCounter64 as mscFrUniVFramerOctetFromOtherVFramer  

MscFrUniLtsRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniLtsRowStatus  
  DisplayString as mscFrUniLtsComponentName  
  StorageType as mscFrUniLtsStorageType  
  NonReplicated as mscFrUniLtsIndex  

MscFrUniLtsSetupEntry  
SEQUENCE    
  Unsigned32 as mscFrUniLtsDuration  
  INTEGER as mscFrUniLtsAlgorithm  
  Unsigned32 as mscFrUniLtsBurstSize  
  Unsigned32 as mscFrUniLtsTimeInterval  

MscFrUniLtsStateEntry  
SEQUENCE    
  INTEGER as mscFrUniLtsGeneratorState  
  INTEGER as mscFrUniLtsCycleIncomplete  
  Unsigned32 as mscFrUniLtsLastActiveInterval  
  FixedPoint3 as mscFrUniLtsLoad  
  Unsigned32 as mscFrUniLtsElapsedGenerationTime  

MscFrUniLtsResultsEntry  
SEQUENCE    
  Counter32 as mscFrUniLtsFramesTx  
  Unsigned32 as mscFrUniLtsBytesTx  
  FixedPoint3 as mscFrUniLtsBitRateTx  
  Unsigned32 as mscFrUniLtsFrameRateTx  

MscFrUniLtsPatRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniLtsPatRowStatus  
  DisplayString as mscFrUniLtsPatComponentName  
  StorageType as mscFrUniLtsPatStorageType  
  Integer32 as mscFrUniLtsPatIndex  

MscFrUniLtsPatDefaultsEntry  
SEQUENCE    
  Unsigned32 as mscFrUniLtsPatDefaultDlci  
  Unsigned32 as mscFrUniLtsPatDefaultNumFrames  
  Unsigned32 as mscFrUniLtsPatDefaultDataSize  
  OCTET STRING as mscFrUniLtsPatDefaultHeaderBits  
  Unsigned32 as mscFrUniLtsPatDefaultHeaderLength  
  Hex as mscFrUniLtsPatDefaultEABits  
  HexString as mscFrUniLtsPatDefaultPayloadPattern  
  INTEGER as mscFrUniLtsPatDefaultRfc1490Header  
  INTEGER as mscFrUniLtsPatDefaultUseBadLrc  

MscFrUniLtsPatSetupEntry  
SEQUENCE    
  Unsigned32 as mscFrUniLtsPatDlci  
  Unsigned32 as mscFrUniLtsPatNumFrames  
  Unsigned32 as mscFrUniLtsPatDataSize  
  OCTET STRING as mscFrUniLtsPatHeaderBits  
  Unsigned32 as mscFrUniLtsPatHeaderLength  
  Hex as mscFrUniLtsPatEaBits  
  HexString as mscFrUniLtsPatPayloadPattern  
  INTEGER as mscFrUniLtsPatRfc1490Header  
  INTEGER as mscFrUniLtsPatUseBadLrc  

MscFrUniLtsPatOpDataEntry  
SEQUENCE    
  HexString as mscFrUniLtsPatFramePattern  
  Unsigned32 as mscFrUniLtsPatHdlcBitsInserted  

MscFrUniLtsPatOpStateEntry  
SEQUENCE    
  FixedPoint3 as mscFrUniLtsPatLoad  
  INTEGER as mscFrUniLtsPatStatus  

MscFrUniCaRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniCaRowStatus  
  DisplayString as mscFrUniCaComponentName  
  StorageType as mscFrUniCaStorageType  
  NonReplicated as mscFrUniCaIndex  

MscFrUniCaProvEntry  
SEQUENCE    
  Unsigned32 as mscFrUniCaOverrideLinkRate  
  Unsigned32 as mscFrUniCaMaximumBandwidthPerCall  

MscFrUniCaIngressCacEntry  
SEQUENCE    
  INTEGER as mscFrUniCaIngressApplyToCos  
  Unsigned32 as mscFrUniCaIngressMaximumEirOnlyCalls  

MscFrUniCaEgressCacEntry  
SEQUENCE    
  INTEGER as mscFrUniCaEgressApplyToCos  
  Unsigned32 as mscFrUniCaEgressMaximumEirOnlyCalls  

MscFrUniCaOpEntry  
SEQUENCE    
  Unsigned32 as mscFrUniCaLinkRate  
  Gauge32 as mscFrUniCaNumberRejectedEgressCirPermConn  
  Gauge32 as mscFrUniCaNumberRejectedEgressEirPermConn  

MscFrUniCaIngCirBPEntry  
SEQUENCE    
  Integer32 as mscFrUniCaIngCirBPIndex  
  Unsigned32 as mscFrUniCaIngCirBPValue  

MscFrUniCaEgCirBpEntry  
SEQUENCE    
  Integer32 as mscFrUniCaEgCirBpIndex  
  Unsigned32 as mscFrUniCaEgCirBpValue  

MscFrUniCaIngCirPoolAdmitBwEntry  
SEQUENCE    
  Integer32 as mscFrUniCaIngCirPoolAdmitBwIndex  
  Gauge32 as mscFrUniCaIngCirPoolAdmitBwValue  

MscFrUniCaIngCirPoolAvailBwEntry  
SEQUENCE    
  Integer32 as mscFrUniCaIngCirPoolAvailBwIndex  
  Gauge32 as mscFrUniCaIngCirPoolAvailBwValue  

MscFrUniCaEgCirPoolAdmitBwEntry  
SEQUENCE    
  Integer32 as mscFrUniCaEgCirPoolAdmitBwIndex  
  Gauge32 as mscFrUniCaEgCirPoolAdmitBwValue  

MscFrUniCaEgCirPoolAvailBwEntry  
SEQUENCE    
  Integer32 as mscFrUniCaEgCirPoolAvailBwIndex  
  Gauge32 as mscFrUniCaEgCirPoolAvailBwValue  

MscFrUniCaIngEirBpEntry  
SEQUENCE    
  Integer32 as mscFrUniCaIngEirBpIndex  
  Unsigned32 as mscFrUniCaIngEirBpValue  

MscFrUniCaEgEirBpEntry  
SEQUENCE    
  Integer32 as mscFrUniCaEgEirBpIndex  
  Unsigned32 as mscFrUniCaEgEirBpValue  

MscFrUniCaIngEirPoolAdmitBwEntry  
SEQUENCE    
  Integer32 as mscFrUniCaIngEirPoolAdmitBwIndex  
  Gauge32 as mscFrUniCaIngEirPoolAdmitBwValue  

MscFrUniCaIngEirPoolAvailBwEntry  
SEQUENCE    
  Integer32 as mscFrUniCaIngEirPoolAvailBwIndex  
  Gauge32 as mscFrUniCaIngEirPoolAvailBwValue  

MscFrUniCaEgEirPoolAdmitBwEntry  
SEQUENCE    
  Integer32 as mscFrUniCaEgEirPoolAdmitBwIndex  
  Gauge32 as mscFrUniCaEgEirPoolAdmitBwValue  

MscFrUniCaEgEirPoolAvailBwEntry  
SEQUENCE    
  Integer32 as mscFrUniCaEgEirPoolAvailBwIndex  
  Gauge32 as mscFrUniCaEgEirPoolAvailBwValue  

MscFrUniCaTpmRowStatusEntry  
SEQUENCE    
  RowStatus as mscFrUniCaTpmRowStatus  
  DisplayString as mscFrUniCaTpmComponentName  
  StorageType as mscFrUniCaTpmStorageType  
  Integer32 as mscFrUniCaTpmIndex  

MscFrUniCaTpmProvEntry  
SEQUENCE    
  Unsigned32 as mscFrUniCaTpmAssignedIngressBandwidthPool  
  Unsigned32 as mscFrUniCaTpmAssignedEgressBandwidthPool