Nortel-MsCarrier-MscPassport-VoiceNetworkingMIB

File: Nortel-MsCarrier-MscPassport-VoiceNetworkingMIB.mib (229342 bytes)

Imported modules

RFC-1212 Nortel-MsCarrier-MscPassport-UsefulDefinitionsMIB Nortel-MsCarrier-MscPassport-StandardTextualConventionsMIB
Nortel-MsCarrier-MscPassport-TextualConventionsMIB

Imported symbols

OBJECT-TYPE mscPassportMIBs mscComponents
Counter32 RowPointer DisplayString
StorageType RowStatus InterfaceIndex
Gauge32 Integer32 Unsigned32
AsciiString Hex NonReplicated
DigitString EnterpriseDateAndTime PassportCounter64
Link

Defined Objects

mscSigChan 1.3.6.1.4.1.562.36.2.1.115
OBJECT IDENTIFIER    

mscSigChanRowStatusTable 1.3.6.1.4.1.562.36.2.1.115.1
This entry controls the addition and deletion of mscSigChan components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanRowStatusEntry

mscSigChanRowStatusEntry 1.3.6.1.4.1.562.36.2.1.115.1.1
A single entry in the table represents a single mscSigChan component.
OBJECT-TYPE    
  MscSigChanRowStatusEntry  

mscSigChanRowStatus 1.3.6.1.4.1.562.36.2.1.115.1.1.1
This variable is used as the basis for SNMP naming of mscSigChan components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscSigChanComponentName 1.3.6.1.4.1.562.36.2.1.115.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscSigChanStorageType 1.3.6.1.4.1.562.36.2.1.115.1.1.4
This variable represents the storage type value for the mscSigChan tables.
OBJECT-TYPE    
  StorageType  

mscSigChanIndex 1.3.6.1.4.1.562.36.2.1.115.1.1.10
This variable represents the index for the mscSigChan tables.
OBJECT-TYPE    
  Integer32 1..16  

mscSigChanBch 1.3.6.1.4.1.562.36.2.1.115.7
OBJECT IDENTIFIER    

mscSigChanBchRowStatusTable 1.3.6.1.4.1.562.36.2.1.115.7.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of mscSigChanBch components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanBchRowStatusEntry

mscSigChanBchRowStatusEntry 1.3.6.1.4.1.562.36.2.1.115.7.1.1
A single entry in the table represents a single mscSigChanBch component.
OBJECT-TYPE    
  MscSigChanBchRowStatusEntry  

mscSigChanBchRowStatus 1.3.6.1.4.1.562.36.2.1.115.7.1.1.1
This variable is used as the basis for SNMP naming of mscSigChanBch components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscSigChanBchComponentName 1.3.6.1.4.1.562.36.2.1.115.7.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscSigChanBchStorageType 1.3.6.1.4.1.562.36.2.1.115.7.1.1.4
This variable represents the storage type value for the mscSigChanBch tables.
OBJECT-TYPE    
  StorageType  

mscSigChanBchIndex 1.3.6.1.4.1.562.36.2.1.115.7.1.1.10
This variable represents the index for the mscSigChanBch tables.
OBJECT-TYPE    
  Integer32 1..331  

mscSigChanBchOperTable 1.3.6.1.4.1.562.36.2.1.115.7.4
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains various operational attributes of a B-channel serviced by a Signalling Channel.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanBchOperEntry

mscSigChanBchOperEntry 1.3.6.1.4.1.562.36.2.1.115.7.4.1
An entry in the mscSigChanBchOperTable.
OBJECT-TYPE    
  MscSigChanBchOperEntry  

mscSigChanBchStatus 1.3.6.1.4.1.562.36.2.1.115.7.4.1.1
This attribute indicates what is current internal B-channel state. The attribute may have the following values for any supported access signalling protocol on Passport: unknown, the B-channel has not registered yet for SigChan services maintB, the B-channel is undergoing a maintenance action idle, the B-channel is available for ingress/egress calls busy, the B-channel is currently being used for an ingress or egress call ingress, the B-channel is currently being used for an ingress call (from the external network to the subnet) egress, the B-channel is currently being used for an egress call (from the subnet to the external network) In addition, CCS protocols supporting SERVICE messaging may also use the following values: idleMaintenance, the B-channel received a SERVICE message placing the channel in maintenance, and no calls are active on the channel ingressMaintenance, the B-channel received a SERVICE message placing the channel in maintenance, and an incoming call is active on the channel egressMaintenance, the B-channel received a SERVICE message placing the channel in maintenance, and an outgoing call is active on the channel outOfService, a SERVICE message to or from the PBX has placed the channel out of service
OBJECT-TYPE    
  INTEGER unknown(0), maintB(1), idle(2), busy(3), ingress(4), egress(5), idleMaintenance(6), ingressMaintenance(7), egressMaintenance(8), outOfService(9)  

mscSigChanBchTimeSlot 1.3.6.1.4.1.562.36.2.1.115.7.4.1.2
This attribute indicates which timeslot the B-channel uses.
OBJECT-TYPE    
  Unsigned32 0..100  

mscSigChanBchVsrInstance 1.3.6.1.4.1.562.36.2.1.115.7.4.1.3
This attribute indicates the component instance of the VoiceSubroute to which the B-channel belongs.
OBJECT-TYPE    
  Unsigned32 0..255  

mscSigChanBchCalledDirectoryNumber 1.3.6.1.4.1.562.36.2.1.115.7.4.1.4
This attribute indicates the dialled number for the currently active call on this B-channel.
OBJECT-TYPE    
  DigitString SIZE(1..32)  

mscSigChanGw 1.3.6.1.4.1.562.36.2.1.115.15
OBJECT IDENTIFIER    

mscSigChanGwRowStatusTable 1.3.6.1.4.1.562.36.2.1.115.15.1
This entry controls the addition and deletion of mscSigChanGw components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanGwRowStatusEntry

mscSigChanGwRowStatusEntry 1.3.6.1.4.1.562.36.2.1.115.15.1.1
A single entry in the table represents a single mscSigChanGw component.
OBJECT-TYPE    
  MscSigChanGwRowStatusEntry  

mscSigChanGwRowStatus 1.3.6.1.4.1.562.36.2.1.115.15.1.1.1
This variable is used as the basis for SNMP naming of mscSigChanGw components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscSigChanGwComponentName 1.3.6.1.4.1.562.36.2.1.115.15.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscSigChanGwStorageType 1.3.6.1.4.1.562.36.2.1.115.15.1.1.4
This variable represents the storage type value for the mscSigChanGw tables.
OBJECT-TYPE    
  StorageType  

mscSigChanGwIndex 1.3.6.1.4.1.562.36.2.1.115.15.1.1.10
This variable represents the index for the mscSigChanGw tables.
OBJECT-TYPE    
  NonReplicated  

mscSigChanGwStatsTable 1.3.6.1.4.1.562.36.2.1.115.15.101
This group provides signalling gateway related statistical attributes for the SigChan component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanGwStatsEntry

mscSigChanGwStatsEntry 1.3.6.1.4.1.562.36.2.1.115.15.101.1
An entry in the mscSigChanGwStatsTable.
OBJECT-TYPE    
  MscSigChanGwStatsEntry  

mscSigChanGwRequiredConversions 1.3.6.1.4.1.562.36.2.1.115.15.101.1.1
This attribute counts the total number of calls that have been made from the subnet to the interface (that is external equipment, for example a PBX) which needed signalling protocol conversion. The value wraps to zero when it exceeds its maximum. The count includes both, supported and unsupported conversions.
OBJECT-TYPE    
  Counter32  

mscSigChanGwUnsupportedConversions 1.3.6.1.4.1.562.36.2.1.115.15.101.1.2
This attribute counts the total number of calls that have been made from the subnet to the interface (that is external equipment, for example a PBX) which needed signalling protocol conversion but were rejected since the requested conversion was not supported. The value wraps to zero when it exceeds its maximum.
OBJECT-TYPE    
  Counter32  

mscSigChanGwGwcTable 1.3.6.1.4.1.562.36.2.1.115.15.301
This attribute has been migrated to gatewayCapability.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanGwGwcEntry

mscSigChanGwGwcEntry 1.3.6.1.4.1.562.36.2.1.115.15.301.1
An entry in the mscSigChanGwGwcTable.
OBJECT-TYPE    
  MscSigChanGwGwcEntry  

mscSigChanGwGwcIndex 1.3.6.1.4.1.562.36.2.1.115.15.301.1.1
This variable represents the mscSigChanGwGwcTable specific index for the mscSigChanGwGwcTable.
OBJECT-TYPE    
  INTEGER etsiQsigPG(0), nisPG(1), analogAndCasPG(2), euroIsdnPG(3), mcdnPG(4), mcdnUniPG(5)  

mscSigChanGwGwcValue 1.3.6.1.4.1.562.36.2.1.115.15.301.1.2
This variable represents an individual value for the mscSigChanGwGwcTable.
OBJECT-TYPE    
  INTEGER noGw(0), singleEndedGw(1), doubleEndedGw(2), singleOrDoubleEndedGw(3), nativePG(4)  

mscSigChanGwGatewayCapTable 1.3.6.1.4.1.562.36.2.1.115.15.302
This attribute indicates the SigChan component's capability to convert from one access signalling type to another. Access signalling protocols (protocols between a Passport and external switching equipment, for example a PBX) are grouped into protocol groups. Protocols within the same protocol group are considered completely compatible. This means that no extra processing is needed when a call originates from an ingress link using protocol A and terminates on an egress link using protocol B if protocols A and B belong to the same protocol group. The following protocol groups are defined: etsiQsigPG - ETSI QSIG protocol group containing ETSI QSIG protocol, mcdnFamilyPG - MCDN Family protocol group containing NIS, Meridian Customer Defined Network (MCDN) peer to peer, and MCDN User to Network (UNI) protocols, analogAndCasPG - Analog and CAS protocol group containing most of the analog and channel associated signalling protocols with steady state line signalling and DTMF register signalling, euroIsdnPG - EURO ISDN protocol group containing most of the European national ISDN protocols based on ETSI ISDN (ETSI-T) standard. For every of the protocols group this attribute indicates what is the level of protocol conversion support available on the SigChan component: noGw - no protocol conversion available for the protocol group, singleEndedGw - only full protocol conversion available for the protocol group (that is the SigChan component on the other side of the subnet does not have to get involved in the gateway processing), doubleEndedGw - only partial protocol conversion available for the protocol group (that is both SigChan components, ingress and egress, have to get involved in signalling conversion), singleOrDoubleEndedGw - both, full and partial protocol conversions available for the protocol group, nativePG - the protocol group is the native protocol group for the SigChan component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanGwGatewayCapEntry

mscSigChanGwGatewayCapEntry 1.3.6.1.4.1.562.36.2.1.115.15.302.1
An entry in the mscSigChanGwGatewayCapTable.
OBJECT-TYPE    
  MscSigChanGwGatewayCapEntry  

mscSigChanGwGatewayCapIndex 1.3.6.1.4.1.562.36.2.1.115.15.302.1.1
This variable represents the mscSigChanGwGatewayCapTable specific index for the mscSigChanGwGatewayCapTable.
OBJECT-TYPE    
  INTEGER etsiQsigPG(0), mcdnPG(1), analogAndCasPG(2), euroIsdnPG(3)  

mscSigChanGwGatewayCapValue 1.3.6.1.4.1.562.36.2.1.115.15.302.1.2
This variable represents an individual value for the mscSigChanGwGatewayCapTable.
OBJECT-TYPE    
  INTEGER noGw(0), singleEndedGw(1), doubleEndedGw(2), singleOrDoubleEndedGw(3), nativePG(4)  

mscSigChanNcas 1.3.6.1.4.1.562.36.2.1.115.16
OBJECT IDENTIFIER    

mscSigChanNcasRowStatusTable 1.3.6.1.4.1.562.36.2.1.115.16.1
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This entry controls the addition and deletion of mscSigChanNcas components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanNcasRowStatusEntry

mscSigChanNcasRowStatusEntry 1.3.6.1.4.1.562.36.2.1.115.16.1.1
A single entry in the table represents a single mscSigChanNcas component.
OBJECT-TYPE    
  MscSigChanNcasRowStatusEntry  

mscSigChanNcasRowStatus 1.3.6.1.4.1.562.36.2.1.115.16.1.1.1
This variable is used as the basis for SNMP naming of mscSigChanNcas components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscSigChanNcasComponentName 1.3.6.1.4.1.562.36.2.1.115.16.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscSigChanNcasStorageType 1.3.6.1.4.1.562.36.2.1.115.16.1.1.4
This variable represents the storage type value for the mscSigChanNcas tables.
OBJECT-TYPE    
  StorageType  

mscSigChanNcasIndex 1.3.6.1.4.1.562.36.2.1.115.16.1.1.10
This variable represents the index for the mscSigChanNcas tables.
OBJECT-TYPE    
  Integer32 0..65535  

mscSigChanNcasOperTable 1.3.6.1.4.1.562.36.2.1.115.16.100
*** THIS TABLE CURRENTLY NOT IMPLEMENTED *** This group contains various operational attributes of a non call-associated signalling session serviced by a SigChan component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanNcasOperEntry

mscSigChanNcasOperEntry 1.3.6.1.4.1.562.36.2.1.115.16.100.1
An entry in the mscSigChanNcasOperTable.
OBJECT-TYPE    
  MscSigChanNcasOperEntry  

mscSigChanNcasDirection 1.3.6.1.4.1.562.36.2.1.115.16.100.1.1
This attribute indicates what is the direction of the non call-associated signalling session. The attribute may have the following values: ingress, the NCAS session is originated by the external equipment into the subnet egress, the NCAS session is originated by the subnet into the external equipment
OBJECT-TYPE    
  INTEGER ingress(1), egress(2)  

mscSigChanNcasCallReference 1.3.6.1.4.1.562.36.2.1.115.16.100.1.2
This attribute indicates which call reference the NCAS session uses.
OBJECT-TYPE    
  Hex 0..65535  

mscSigChanNcasCalledDirectoryNumber 1.3.6.1.4.1.562.36.2.1.115.16.100.1.3
This attribute indicates the dialled number for the NCAS session.
OBJECT-TYPE    
  DigitString SIZE(1..32)  

mscSigChanNcasDuration 1.3.6.1.4.1.562.36.2.1.115.16.100.1.4
This attribute indicates duration of the NCAS session since its establishment.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscSigChanICmap 1.3.6.1.4.1.562.36.2.1.115.18
OBJECT IDENTIFIER    

mscSigChanICmapRowStatusTable 1.3.6.1.4.1.562.36.2.1.115.18.1
This entry controls the addition and deletion of mscSigChanICmap components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanICmapRowStatusEntry

mscSigChanICmapRowStatusEntry 1.3.6.1.4.1.562.36.2.1.115.18.1.1
A single entry in the table represents a single mscSigChanICmap component.
OBJECT-TYPE    
  MscSigChanICmapRowStatusEntry  

mscSigChanICmapRowStatus 1.3.6.1.4.1.562.36.2.1.115.18.1.1.1
This variable is used as the basis for SNMP naming of mscSigChanICmap components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscSigChanICmapComponentName 1.3.6.1.4.1.562.36.2.1.115.18.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscSigChanICmapStorageType 1.3.6.1.4.1.562.36.2.1.115.18.1.1.4
This variable represents the storage type value for the mscSigChanICmap tables.
OBJECT-TYPE    
  StorageType  

mscSigChanICmapIndex 1.3.6.1.4.1.562.36.2.1.115.18.1.1.10
This variable represents the index for the mscSigChanICmap tables.
OBJECT-TYPE    
  NonReplicated  

mscSigChanICmapIntCauseTable 1.3.6.1.4.1.562.36.2.1.115.18.100
This group contains the provisionable, Passport generated clearing reasons of an establishing call.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanICmapIntCauseEntry

mscSigChanICmapIntCauseEntry 1.3.6.1.4.1.562.36.2.1.115.18.100.1
An entry in the mscSigChanICmapIntCauseTable.
OBJECT-TYPE    
  MscSigChanICmapIntCauseEntry  

mscSigChanICmapEgressLinkOutOfServCause 1.3.6.1.4.1.562.36.2.1.115.18.100.1.1
This attribute specifies the cause code sent to the originating PBX when the data link to the remote PBX is down or when remote channels are in maintenance. If the component is not added or if the default value autoConfigure is provisioned for the attribute the cause code sent to the originating PBX is not manipulated and the clearing process is not influenced. For this case, a typical cause code value sent back to the originating PBX is 27. VALUES ( 128 = autoConfigure )
OBJECT-TYPE    
  Unsigned32 0..127 | 128  

mscSigChanICmapChanOrCircNotAvailCause 1.3.6.1.4.1.562.36.2.1.115.18.100.1.2
This attribute specifies the cause code sent to the originating PBX if no timeslot is available for an incoming call. If the component is not added or if the default value autoConfigure is provisioned for the attribute the cause code sent to the originating PBX is not manipulated and the clearing process is not influenced. For this case, a typical cause code value sent back to the originating PBX is 34. VALUES ( 128 = autoConfigure )
OBJECT-TYPE    
  Unsigned32 0..127 | 128  

mscSigChanICmapTempFailureCause 1.3.6.1.4.1.562.36.2.1.115.18.100.1.3
This attribute specifies the cause code sent to the originating PBX when PORS fails to establish a call due to congestion or a disabled trunk. It is also generated when the calling side fails to decode payload capabilities sent by the called side. If the component is not added or if the default value autoConfigure is provisioned for the attribute the cause code sent to the originating PBX is not manipulated and the clearing process is not influenced. For this case, a typical cause code value sent back to the originating PBX is 41. VALUES ( 128 = autoConfigure )
OBJECT-TYPE    
  Unsigned32 0..127 | 128  

mscSigChanICmapSwitchCongestCause 1.3.6.1.4.1.562.36.2.1.115.18.100.1.4
This attribute specifies the cause code sent to the originating PBX when the allocation of internal resources for an incoming call fails. If the component is not added or if the default value autoConfigure is provisioned for the attribute the cause code sent to the originating PBX is not manipulated and the clearing process is not influenced. For this case, typical cause code values sent back to the originating PBX are 42 for NIS and 41 for ETSI. VALUES ( 128 = autoConfigure )
OBJECT-TYPE    
  Unsigned32 0..127 | 128  

mscSigChanICmapReqChanOrCircNotAvailCause 1.3.6.1.4.1.562.36.2.1.115.18.100.1.5
This attribute specifies the cause code sent to the originating PBX when an exclusively requested channel is not in service or a channel request is unsuccessful. If the component is not added or if the default value autoConfigure is provisioned for the attribute the cause code sent to the originating PBX is not manipulated and the clearing process is not influenced. For this case, a typical cause code value sent back to the originating PBX is 44. VALUES ( 128 = autoConfigure )
OBJECT-TYPE    
  Unsigned32 0..127 | 128  

mscSigChanICmapResourceUnavailCause 1.3.6.1.4.1.562.36.2.1.115.18.100.1.6
This attribute specifies the cause code sent to the originating PBX when the path establishing timer expires, when the switched voice service associated to a call is locked by CAS or when an H-channel is requested. If the component is not added or if the default value autoConfigure is provisioned for the attribute the cause code sent to the originating PBX is not manipulated and the clearing process is not influenced. For this case, typical cause code values sent back to the originating PBX are 47 for NIS and 44 for ETSI. VALUES ( 128 = autoConfigure )
OBJECT-TYPE    
  Unsigned32 0..127 | 128  

mscSigChanICmapServNotAllowedCause 1.3.6.1.4.1.562.36.2.1.115.18.100.1.7
This attribute specifies the cause code sent to the originating PBX when the requested call type (voice or data) is not compatible with Vroute typeOfRoute at the calling side. If the component is not added or if the default value autoConfigure is provisioned for the attribute the cause code sent to the originating PBX is not manipulated and the clearing process is not influenced. For this case, a typical cause code value sent back to the originating PBX is 63. VALUES ( 128 = autoConfigure )
OBJECT-TYPE    
  Unsigned32 0..127 | 128  

mscSigChanICmapNoSuchChannelCause 1.3.6.1.4.1.562.36.2.1.115.18.100.1.8
This attribute specifies the cause code sent to the originating PBX when a requested channel does not exist. If the component is not added or if the default value autoConfigure is provisioned for the attribute the cause code sent to the originating PBX is not manipulated and the clearing process is not influenced. For this case, a typical cause code value sent back to the originating PBX is 82. VALUES ( 128 = autoConfigure )
OBJECT-TYPE    
  Unsigned32 0..127 | 128  

mscSigChanICmapIncompatDestCause 1.3.6.1.4.1.562.36.2.1.115.18.100.1.9
This attribute specifies the cause code sent to the originating PBX when the calling and called side capabilities do not match. If the component is not added or if the default value autoConfigure is provisioned for the attribute the cause code sent to the originating PBX is not manipulated and the clearing process is not influenced. For this case, a typical cause code value sent back to the originating PBX is 88. VALUES ( 128 = autoConfigure )
OBJECT-TYPE    
  Unsigned32 0..127 | 128  

mscSigChanCidDataTable 1.3.6.1.4.1.562.36.2.1.115.100
This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanCidDataEntry

mscSigChanCidDataEntry 1.3.6.1.4.1.562.36.2.1.115.100.1
An entry in the mscSigChanCidDataTable.
OBJECT-TYPE    
  MscSigChanCidDataEntry  

mscSigChanCustomerIdentifier 1.3.6.1.4.1.562.36.2.1.115.100.1.1
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
OBJECT-TYPE    
  Unsigned32 0 | 1..8191  

mscSigChanIfEntryTable 1.3.6.1.4.1.562.36.2.1.115.101
This group contains the provisionable attributes for the ifEntry.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanIfEntryEntry

mscSigChanIfEntryEntry 1.3.6.1.4.1.562.36.2.1.115.101.1
An entry in the mscSigChanIfEntryTable.
OBJECT-TYPE    
  MscSigChanIfEntryEntry  

mscSigChanIfAdminStatus 1.3.6.1.4.1.562.36.2.1.115.101.1.1
The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mscSigChanIfIndex 1.3.6.1.4.1.562.36.2.1.115.101.1.2
This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
OBJECT-TYPE    
  InterfaceIndex 1..65535  

mscSigChanOperStatusTable 1.3.6.1.4.1.562.36.2.1.115.102
This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanOperStatusEntry

mscSigChanOperStatusEntry 1.3.6.1.4.1.562.36.2.1.115.102.1
An entry in the mscSigChanOperStatusTable.
OBJECT-TYPE    
  MscSigChanOperStatusEntry  

mscSigChanSnmpOperStatus 1.3.6.1.4.1.562.36.2.1.115.102.1.1
The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mscSigChanStateTable 1.3.6.1.4.1.562.36.2.1.115.103
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanStateEntry

mscSigChanStateEntry 1.3.6.1.4.1.562.36.2.1.115.103.1
An entry in the mscSigChanStateTable.
OBJECT-TYPE    
  MscSigChanStateEntry  

mscSigChanAdminState 1.3.6.1.4.1.562.36.2.1.115.103.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscSigChanOperationalState 1.3.6.1.4.1.562.36.2.1.115.103.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscSigChanUsageState 1.3.6.1.4.1.562.36.2.1.115.103.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscSigChanProvTable 1.3.6.1.4.1.562.36.2.1.115.104
This group represents the provisionable attributes of a SigChan.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanProvEntry

mscSigChanProvEntry 1.3.6.1.4.1.562.36.2.1.115.104.1
An entry in the mscSigChanProvTable.
OBJECT-TYPE    
  MscSigChanProvEntry  

mscSigChanCommentText 1.3.6.1.4.1.562.36.2.1.115.104.1.1
Use of this attribute is at the discretion of the system administrator. Typically, this attribute specifies the name of the customer that is using this SigChan.
OBJECT-TYPE    
  AsciiString SIZE(0..40)  

mscSigChanOctothorpeEod 1.3.6.1.4.1.562.36.2.1.115.104.1.2
This attribute specifies whether the octothorpe should be used as an end of dialling indication. When this character is received, only the digits that have been received to that point will be used for address resolution. All subsequent digits will be forwarded to the far-end, but they will not be used. The octothorpe will not be sent to the far-end.
OBJECT-TYPE    
  INTEGER yes(0), no(1)  

mscSigChanForceNpiTon 1.3.6.1.4.1.562.36.2.1.115.104.1.3
This attribute, together with the defaultNpiTon attribute, controls Numbering Plan Identifier (NPI) and Type Of Number (TON) values to be used by the SigChan component for egress calls (if applicable). If set to yes, NPI and TON values defined by the defaultNpiTon attribute unconditionally overwrite values received in the call setup message from the subnet.
OBJECT-TYPE    
  INTEGER yes(0), no(1)  

mscSigChanDefaultNpiTon 1.3.6.1.4.1.562.36.2.1.115.104.1.4
This attribute, together with the forceNpiTon attribute, controls Numbering Plan Identifier (NPI) and Type Of Number (TON) values to be used by the SigChan component for egress calls (if applicable). The combination of NPI and TON values defined by the defaultNpiTon attribute is used for an egress call whenever: - the call setup message received from subnet indicates that NPI or TON information is not supplied or doesn't make sense, or - attribute forceNpiTon is set to yes Mapping between values of the defaultNpiTon attribute and associated combinations of NPI and TON values follows: casUnknown: NPI=unknown (0) TON=unknown (0) unknown: NPI=E.164 (1) TON=unknown (0) international: NPI=E.164 (1) TON=international (1) national: NPI=E.164 (1) TON=national (2) subscriber: NPI=E.164 (1) TON=subscriber (4) p0: NPI=private(9) TON=0 p1: NPI=private(9) TON=1 p2: NPI=private(9) TON=2 p3: NPI=private(9) TON=3 p4: NPI=private(9) TON=4 p5: NPI=private(9) TON=5 p6: NPI=private(9) TON=6 p7: NPI=private(9) TON=7
OBJECT-TYPE    
  INTEGER unknown(0), international(1), national(2), subscriber(3), p0(4), p1(5), p2(6), p3(7), p4(8), p5(9), p6(10), p7(11), casUnknown(12)  

mscSigChanSubroutesTable 1.3.6.1.4.1.562.36.2.1.115.307
This attribute identifies all of the VoiceSubroutes which are associated with this signalling channel.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanSubroutesEntry

mscSigChanSubroutesEntry 1.3.6.1.4.1.562.36.2.1.115.307.1
An entry in the mscSigChanSubroutesTable.
OBJECT-TYPE    
  MscSigChanSubroutesEntry  

mscSigChanSubroutesValue 1.3.6.1.4.1.562.36.2.1.115.307.1.1
This variable represents both the value and the index for the mscSigChanSubroutesTable.
OBJECT-TYPE    
  Link  

mscSigChanSubroutesRowStatus 1.3.6.1.4.1.562.36.2.1.115.307.1.2
This variable is used to control the addition and deletion of individual values of the mscSigChanSubroutesTable.
OBJECT-TYPE    
  RowStatus  

mscSigChanDegradedSubroutesTable 1.3.6.1.4.1.562.36.2.1.115.308
This attribute lists all of the VoiceSubroute components that do not have all of their SwitchedVoiceService subcomponents available for use.
OBJECT-TYPE    
  SEQUENCE OF  
    MscSigChanDegradedSubroutesEntry

mscSigChanDegradedSubroutesEntry 1.3.6.1.4.1.562.36.2.1.115.308.1
An entry in the mscSigChanDegradedSubroutesTable.
OBJECT-TYPE    
  MscSigChanDegradedSubroutesEntry  

mscSigChanDegradedSubroutesValue 1.3.6.1.4.1.562.36.2.1.115.308.1.1
This variable represents both the value and the index for the mscSigChanDegradedSubroutesTable.
OBJECT-TYPE    
  RowPointer  

mscVRoute 1.3.6.1.4.1.562.36.2.1.116
OBJECT IDENTIFIER    

mscVRouteRowStatusTable 1.3.6.1.4.1.562.36.2.1.116.1
This entry controls the addition and deletion of mscVRoute components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteRowStatusEntry

mscVRouteRowStatusEntry 1.3.6.1.4.1.562.36.2.1.116.1.1
A single entry in the table represents a single mscVRoute component.
OBJECT-TYPE    
  MscVRouteRowStatusEntry  

mscVRouteRowStatus 1.3.6.1.4.1.562.36.2.1.116.1.1.1
This variable is used as the basis for SNMP naming of mscVRoute components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscVRouteComponentName 1.3.6.1.4.1.562.36.2.1.116.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscVRouteStorageType 1.3.6.1.4.1.562.36.2.1.116.1.1.4
This variable represents the storage type value for the mscVRoute tables.
OBJECT-TYPE    
  StorageType  

mscVRouteIndex 1.3.6.1.4.1.562.36.2.1.116.1.1.10
This variable represents the index for the mscVRoute tables.
OBJECT-TYPE    
  Integer32 1..16  

mscVRouteDebug 1.3.6.1.4.1.562.36.2.1.116.2
OBJECT IDENTIFIER    

mscVRouteDebugRowStatusTable 1.3.6.1.4.1.562.36.2.1.116.2.1
This entry controls the addition and deletion of mscVRouteDebug components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteDebugRowStatusEntry

mscVRouteDebugRowStatusEntry 1.3.6.1.4.1.562.36.2.1.116.2.1.1
A single entry in the table represents a single mscVRouteDebug component.
OBJECT-TYPE    
  MscVRouteDebugRowStatusEntry  

mscVRouteDebugRowStatus 1.3.6.1.4.1.562.36.2.1.116.2.1.1.1
This variable is used as the basis for SNMP naming of mscVRouteDebug components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscVRouteDebugComponentName 1.3.6.1.4.1.562.36.2.1.116.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscVRouteDebugStorageType 1.3.6.1.4.1.562.36.2.1.116.2.1.1.4
This variable represents the storage type value for the mscVRouteDebug tables.
OBJECT-TYPE    
  StorageType  

mscVRouteDebugIndex 1.3.6.1.4.1.562.36.2.1.116.2.1.1.10
This variable represents the index for the mscVRouteDebug tables.
OBJECT-TYPE    
  NonReplicated  

mscVRouteInterface 1.3.6.1.4.1.562.36.2.1.116.3
OBJECT IDENTIFIER    

mscVRouteInterfaceRowStatusTable 1.3.6.1.4.1.562.36.2.1.116.3.1
This entry controls the addition and deletion of mscVRouteInterface components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteInterfaceRowStatusEntry

mscVRouteInterfaceRowStatusEntry 1.3.6.1.4.1.562.36.2.1.116.3.1.1
A single entry in the table represents a single mscVRouteInterface component.
OBJECT-TYPE    
  MscVRouteInterfaceRowStatusEntry  

mscVRouteInterfaceRowStatus 1.3.6.1.4.1.562.36.2.1.116.3.1.1.1
This variable is used as the basis for SNMP naming of mscVRouteInterface components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscVRouteInterfaceComponentName 1.3.6.1.4.1.562.36.2.1.116.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscVRouteInterfaceStorageType 1.3.6.1.4.1.562.36.2.1.116.3.1.1.4
This variable represents the storage type value for the mscVRouteInterface tables.
OBJECT-TYPE    
  StorageType  

mscVRouteInterfaceIndex 1.3.6.1.4.1.562.36.2.1.116.3.1.1.10
This variable represents the index for the mscVRouteInterface tables.
OBJECT-TYPE    
  NonReplicated  

mscVRouteInterfaceProvTable 1.3.6.1.4.1.562.36.2.1.116.3.10
This group contains attributes specifying the interface to a PBX.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteInterfaceProvEntry

mscVRouteInterfaceProvEntry 1.3.6.1.4.1.562.36.2.1.116.3.10.1
An entry in the mscVRouteInterfaceProvTable.
OBJECT-TYPE    
  MscVRouteInterfaceProvEntry  

mscVRouteInterfaceIngressAudioGain 1.3.6.1.4.1.562.36.2.1.116.3.10.1.1
This attribute specifies the gain in dB that is applied to data coming from outside the network before it is transferred across the network. It applies to voice, modem and fax traffic. For example, ingress gain is applied to audio data coming from a PBX. If ingressAudioGain is negative, a loss is applied. ingressAudioGain and egressAudioGain are used in loss planning, which is the configuration of the devices in a network to ensure that the signal level from any point in the network to any other point is correct. ingressAudioGain is ignored for calls on 1pDS1V and 1pE1V cards. For calls running on these cards, ingress audio gain is not under the user's control and egress audio gain is determined by the audioGain attribute in the appropriate Vncs/m VoiceProfile/n.
OBJECT-TYPE    
  INTEGER -12..12  

mscVRouteInterfaceEgressAudioGain 1.3.6.1.4.1.562.36.2.1.116.3.10.1.2
This attribute specifies the gain in dB that is applied to data leaving the network. It applies to voice, modem and fax traffic. For example, egress gain is applied to audio data going to a PBX. If egressAudioGain is negative, a loss is applied. ingressAudioGain and egressAudioGain are used in loss planning, which is the configuration of the devices in the network to ensure that the signal level from any point in the network to any other point is correct. egressAudioGain is ignored for calls running on 1pDS1V and 1pE1V cards. For calls running on these cards, egress audio gain is determined by the audioGain attribute in the appropriate Vncs/m VoiceProfile/n.
OBJECT-TYPE    
  INTEGER -12..12  

mscVRouteInterfaceTandemPassThrough 1.3.6.1.4.1.562.36.2.1.116.3.10.1.3
This attribute specifies whether tandem pass through is desired. If tandemPassThrough is enabled, tandem pass through is used if possible. If tandemPassThrough is disabled, tandem pass through is not used under any circumstances. The actual state of tandem pass through is indicated in Vsr Svs Framer tptStatus. The negotiated tandem pass through is available in Vsr Svs Framer negotiatedTandemPassThrough. Tandem pass through is not supported on 1pDS1V and 1pE1V cards, so tandemPassThrough is ignored on these cards.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscVRouteInterfaceEchoCancellation 1.3.6.1.4.1.562.36.2.1.116.3.10.1.5
This attribute has been migrated to echoCancellation.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscVRouteInterfaceComfortNoiseCap 1.3.6.1.4.1.562.36.2.1.116.3.10.1.6
This attribute specifies the maximum level at which comfort noise is generated. The comfort noise is limited by comfortNoiseCap before egressAudioGain is applied. The default value of -40 dBm0 equates to the maximum level of comfort noise available and effectively disables the comfortNoiseCap.
OBJECT-TYPE    
  INTEGER -78 | -65 | -60 | -54 | -52 | -50 | -48 | -46 | -44 | -42 | -40  

mscVRouteInterfaceSpeechHangoverTime 1.3.6.1.4.1.562.36.2.1.116.3.10.1.7
This attribute specifies the time after the end of speech before silence suppression starts. It applies only to voice traffic. It is not used unless Vsr Svs Framer negotiatedSilenceSuppression is on, congested or slowAndCongested. Higher values of speechHangoverTime reduce undesirable clipping but increase bandwidth usage. speechHangoverTime is not used on DS1V, E1V, 1pDS1V, 1pE1V and J2MV cards.
OBJECT-TYPE    
  Unsigned32 10..500  

mscVRouteInterfaceFaxHangoverTimeG711G726 1.3.6.1.4.1.562.36.2.1.116.3.10.1.8
This attribute specifies the time after the end of fax traffic before G.711/G.726 fax idle suppression starts. It applies only if the negotiated fax encoding, available in Vsr Svs Framer negotiatedEncoding, is g711, g726 or g711G726 and Vsr Svs Framer negotiatedFisG711G726 is on. Higher values of faxHangoverTimeG711G726 reduce undesirable clipping but increase bandwidth usage. faxHangoverTimeG711G726 is not used on DS1V, E1V, 1pDS1V, 1pE1V and J2MV cards.
OBJECT-TYPE    
  Unsigned32 300..20000  

mscVRouteInterfaceModemFaxSpeechDiscrim 1.3.6.1.4.1.562.36.2.1.116.3.10.1.9
This attribute specifies whether this VoiceRoute differentiates between modemFax traffic and speech. If modemFaxSpeechDiscrim is on and a false 2100 Hz tone is detected, any Svs using this route reverts to speech mode when speech is detected. modemFaxSpeechDiscrim is not used on DS1V, E1V, 1pDS1V, 1pE1V and J2MV cards.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscVRouteInterfaceEchoTailDelay 1.3.6.1.4.1.562.36.2.1.116.3.10.1.10
This attribute specifies the maximum echo canceller tail delay coverage. It should be selected higher than the summation of the round trip delay of echo and hybrid response time. A 32 msec setting is good for a radius of 2700 km, assuming that the signal is going through 4 exchanges and the hybrid response time is 6 msec. A 64 msec setting offers even greater coverage (more distance or more switches), with comparable convergence time. The recommended setting is 64 msec. This attribute is not used on DS1V, E1V, 1pDS1V, 1pE1V, J2MV, 1pE1Mvp, 1pDS1Mvp, or 1pTTC2mMvp card.
OBJECT-TYPE    
  Unsigned32 32 | 64  

mscVRouteInterfaceEchoReturnLoss 1.3.6.1.4.1.562.36.2.1.116.3.10.1.11
This attribute specifies the echo return loss parameter of the echo canceller. 0 db is the normal value for most line conditions. If the line quality is poor, in terms of echo, selecting a higher value may allow the echo canceller to perform better. A side effect is that the voice level is attenuated by the same amount, which may not always be acceptable. This attribute is not used on DS1V, E1V, 1pDS1V, 1pE1V, J2MV, 1pE1Mvp, 1pDS1Mvp, or 1pTTC2mMvp card.
OBJECT-TYPE    
  Unsigned32 0 | 3 | 6  

mscVRouteInterfaceEcanBypassMode 1.3.6.1.4.1.562.36.2.1.116.3.10.1.15
This attribute specifies when version 2 internal echo cancellers are placed in bypass mode on this VoiceRoute. This attribute only applies if v2 of echoCancellation is on. If ecanBypassMode is g165, the internal echo canceller is placed in bypass mode as per ITU-T G.165. If ecanBypassMode is g164, the internal echo canceller is placed in bypass mode as per ITU-T G.164. If ecanBypassMode is never, the internal echo canceller is never placed in bypass mode. This mode should only be used for debugging. This attribute does not apply to 1pE1V, 1pDS1V, J2MV, 1pE1Mvp, 1pDS1Mvp or 1pTTC2mMvp cards.
OBJECT-TYPE    
  INTEGER g164(0), g165(1), never(2)  

mscVRouteInterfaceStructuredEchoCancellationTable 1.3.6.1.4.1.562.36.2.1.116.3.474
This attribute specifies whether echo cancellation is performed on this VoiceRoute. v1 specifies whether echo cancellation is performed by version 1 internal echo cancellers. v2 specifes whether echo cancellation is performed by version 2 echo cancellers. If echoCancellation is on, the internal echo canceller is enabled and echo cancellation is performed. If echoCancellation is off, the internal echo canceller is placed in transparent bypass mode and echo cancellation is never performed.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteInterfaceStructuredEchoCancellationEntry

mscVRouteInterfaceStructuredEchoCancellationEntry 1.3.6.1.4.1.562.36.2.1.116.3.474.1
An entry in the mscVRouteInterfaceStructuredEchoCancellationTable.
OBJECT-TYPE    
  MscVRouteInterfaceStructuredEchoCancellationEntry  

mscVRouteInterfaceStructuredEchoCancellationIndex 1.3.6.1.4.1.562.36.2.1.116.3.474.1.1
This variable represents the mscVRouteInterfaceStructuredEchoCancellationTable specific index for the mscVRouteInterfaceStructuredEchoCancellationTable.
OBJECT-TYPE    
  INTEGER v1(0), v2(1)  

mscVRouteInterfaceStructuredEchoCancellationValue 1.3.6.1.4.1.562.36.2.1.116.3.474.1.2
This variable represents an individual value for the mscVRouteInterfaceStructuredEchoCancellationTable.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscVRouteDna 1.3.6.1.4.1.562.36.2.1.116.4
OBJECT IDENTIFIER    

mscVRouteDnaRowStatusTable 1.3.6.1.4.1.562.36.2.1.116.4.1
This entry controls the addition and deletion of mscVRouteDna components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteDnaRowStatusEntry

mscVRouteDnaRowStatusEntry 1.3.6.1.4.1.562.36.2.1.116.4.1.1
A single entry in the table represents a single mscVRouteDna component.
OBJECT-TYPE    
  MscVRouteDnaRowStatusEntry  

mscVRouteDnaRowStatus 1.3.6.1.4.1.562.36.2.1.116.4.1.1.1
This variable is used as the basis for SNMP naming of mscVRouteDna components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscVRouteDnaComponentName 1.3.6.1.4.1.562.36.2.1.116.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscVRouteDnaStorageType 1.3.6.1.4.1.562.36.2.1.116.4.1.1.4
This variable represents the storage type value for the mscVRouteDna tables.
OBJECT-TYPE    
  StorageType  

mscVRouteDnaIndex 1.3.6.1.4.1.562.36.2.1.116.4.1.1.10
This variable represents the index for the mscVRouteDna tables.
OBJECT-TYPE    
  NonReplicated  

mscVRouteDnaAddressTable 1.3.6.1.4.1.562.36.2.1.116.4.10
Address group contains attributes common to all Dna's. Every Dna used in the network is defined with this group of 2 attributes. String of address digits is complemented by type of address and Npi. These attributes are used to interpret format of the address digits.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteDnaAddressEntry

mscVRouteDnaAddressEntry 1.3.6.1.4.1.562.36.2.1.116.4.10.1
An entry in the mscVRouteDnaAddressTable.
OBJECT-TYPE    
  MscVRouteDnaAddressEntry  

mscVRouteDnaNumberingPlanIndicator 1.3.6.1.4.1.562.36.2.1.116.4.10.1.1
This attribute indicates the Numbering Plan Indicator (NPI) of the Dna that is entered. Address may belong to X.121 or E.164 plans. X.121 is used in packet svitched data networks.
OBJECT-TYPE    
  INTEGER x121(0), e164(1)  

mscVRouteDnaDataNetworkAddress 1.3.6.1.4.1.562.36.2.1.116.4.10.1.2
Dna attribute contains digits which form unique identifier of the customer interface. It can be compared (approximation only) to telephone number where phone number identifies unique telephone set. Dna digits are selected and assigned by network operators.
OBJECT-TYPE    
  DigitString SIZE(0..15)  

mscVRouteAcct 1.3.6.1.4.1.562.36.2.1.116.5
OBJECT IDENTIFIER    

mscVRouteAcctRowStatusTable 1.3.6.1.4.1.562.36.2.1.116.5.1
This entry controls the addition and deletion of mscVRouteAcct components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteAcctRowStatusEntry

mscVRouteAcctRowStatusEntry 1.3.6.1.4.1.562.36.2.1.116.5.1.1
A single entry in the table represents a single mscVRouteAcct component.
OBJECT-TYPE    
  MscVRouteAcctRowStatusEntry  

mscVRouteAcctRowStatus 1.3.6.1.4.1.562.36.2.1.116.5.1.1.1
This variable is used as the basis for SNMP naming of mscVRouteAcct components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscVRouteAcctComponentName 1.3.6.1.4.1.562.36.2.1.116.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscVRouteAcctStorageType 1.3.6.1.4.1.562.36.2.1.116.5.1.1.4
This variable represents the storage type value for the mscVRouteAcct tables.
OBJECT-TYPE    
  StorageType  

mscVRouteAcctIndex 1.3.6.1.4.1.562.36.2.1.116.5.1.1.10
This variable represents the index for the mscVRouteAcct tables.
OBJECT-TYPE    
  NonReplicated  

mscVRouteAcctProvTable 1.3.6.1.4.1.562.36.2.1.116.5.2
This group contains the provisionable attributes of a VoiceAccounting component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteAcctProvEntry

mscVRouteAcctProvEntry 1.3.6.1.4.1.562.36.2.1.116.5.2.1
An entry in the mscVRouteAcctProvTable.
OBJECT-TYPE    
  MscVRouteAcctProvEntry  

mscVRouteAcctAccountCollection 1.3.6.1.4.1.562.36.2.1.116.5.2.1.2
This attribute specifies that accounting records are to be collected for the various reasons: bill, test, study, audit. The last of the parameters, force, specifies that accounting records are to be collected irrespective of other collection reasons. If none of these reasons is set, then accounting will be suppressed. Description of bits: bill(0) test(1) study(2) audit(3) force(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscVRouteAcctAccountClass 1.3.6.1.4.1.562.36.2.1.116.5.2.1.3
This attribute specifies the accounting class which is reserved for network operations usage. Its value is returned in the accounting record in the local and remote service type attributes. The use of this attribute is decided by the network operator.
OBJECT-TYPE    
  Unsigned32 0..255  

mscVRouteAcctServiceExchange 1.3.6.1.4.1.562.36.2.1.116.5.2.1.4
This attribute specifies a user defined value, Data Service Exchange, as entered by the network operator and reported in the accounting record.
OBJECT-TYPE    
  Unsigned32 0..255  

mscVRouteAcctDigitsSuppressed 1.3.6.1.4.1.562.36.2.1.116.5.2.1.5
This attribute specifies the number of trailing digits which will be suppressed in the calledNumber in the accounting records. Each of the specified number of trailing digits are replaced with an 'X'. This option exists to satisfy privacy requirements in a number of countries.
OBJECT-TYPE    
  Unsigned32 0..8  

mscVRouteAcctAccountingOptions 1.3.6.1.4.1.562.36.2.1.116.5.2.1.6
This attribute specifies optional settings for the voice networking accounting system. The options are: suppressTerminatingEndRecords - setting this option suppresses the generation of accounting records at the destination node. This reduces the volume of accounting data. This option has local significance only. It only suppresses the generation of accounting records for calls received by this node. Description of bits: notused0(0) suppressTerminatingEndRecords(1)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscVRouteProvTable 1.3.6.1.4.1.562.36.2.1.116.10
This group contains the provisionable attributes of a Voice Networking VoiceRoute component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteProvEntry

mscVRouteProvEntry 1.3.6.1.4.1.562.36.2.1.116.10.1
An entry in the mscVRouteProvTable.
OBJECT-TYPE    
  MscVRouteProvEntry  

mscVRouteCommentText 1.3.6.1.4.1.562.36.2.1.116.10.1.1
Use of this attribute is at the discretion of the system administrator. Typically, it specifies the name of the customer that is using this VoiceRoute.
OBJECT-TYPE    
  AsciiString SIZE(0..40)  

mscVRouteTypeOfRoute 1.3.6.1.4.1.562.36.2.1.116.10.1.2
This attribute specifies the type of calls (either voice, data, or both voice and data) that this VoiceRoute will accept from the Passport subnet and the local PBX. If typeOfRoute is set to voice, then all data calls from the subnet and the local PBX will be rejected. If typeOfRoute is set to data, then all voice calls from the subnet and the local PBX will be rejected. If typeOfRoute is set to voiceData, then all data and voice calls will be accepted from the subnet and the local PBX.
OBJECT-TYPE    
  INTEGER voice(0), data(1), voiceData(2)  

mscVRouteDiallingPlan0 1.3.6.1.4.1.562.36.2.1.116.10.1.6
This attribute specifies how to map the numbering plan indication and the type of number into the Vncs database diallingPlan0. For more information refer to NTP 241-7001-4xx Voice Networking Users Guide. There are three numbering plans that are allowed, unknown, E.164, and private. Within each of these, there are eight possible type of numbers. Since the name for the type of numbers for the private numbering plans varies from protocol to protocol, a generic scheme has been adopted. unknown means that the sending and receiving switches have no knowledge of the numbering plan. international means that the sending switch has identified the number format as matching the E.164 international dialling. national means that the sending switch has identified the number as conforming to the E.164 national dialling plan subscriber means that the number is the address of a customer conforming to the local public network. p0, p1, p2, p3, p4, p5, p6 and p7 are private numbering plans, with a type of number zero to seven. casUnknown means any number received from a Channel Associated Signalling (CAS) trunk. Description of bits: unknown(0) international(1) national(2) subscriber(3) p0(4) p1(5) p2(6) p3(7) p4(8) p5(9) p6(10) p7(11) casUnknown(12)
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

mscVRouteDiallingPlan1 1.3.6.1.4.1.562.36.2.1.116.10.1.7
This attribute specifies how to map the numbering plan indication and the type of number into the Vncs database diallingPlan1. For more information refer to NTP 241-7001-4xx Voice Networking Users Guide. There are three numbering plans that are allowed, unknown, E.164, and private. Within each of these, there are eight possible type of numbers. Since the name for the type of numbers for the private numbering plans varies from protocol to protocol, a generic scheme has been adopted. unknown means that the sending and receiving switches have no knowledge of the numbering plan. international means that the sending switch has identified the number format as matching the E.164 international dialling plan. national means that the sending switch has identified the number as conforming to the E.164 national dialling plan subscriber means that the number is the address of a customer conforming to the local public network. p0, p1, p2, p3, p4, p5, p6 and p7 are private numbering plans, with a type of number zero to seven. casUnknown means any number received from a Channel Associated Signalling (CAS) trunk. Description of bits: unknown(0) international(1) national(2) subscriber(3) p0(4) p1(5) p2(6) p3(7) p4(8) p5(9) p6(10) p7(11) casUnknown(12)
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

mscVRouteDiallingPlan2 1.3.6.1.4.1.562.36.2.1.116.10.1.8
This attribute specifies how to map the numbering plan indication and the type of number into the Vncs database diallingPlan2. For more information refer to NTP 241-7001-4xx Voice Networking Users Guide. There are three numbering plans that are allowed, unknown, E.164, and private. Within each of these, there are eight possible type of numbers. Since the name for the type of numbers for the private numbering plans varies from protocol to protocol, a generic scheme has been adopted. unknown means that the sending and receiving switches have no knowledge of the numbering plan. international means that the sending switch has identified the number format as matching the E.164 international dialling plan. national means that the sending switch has identified the number as conforming to the E.164 national dialling plan subscriber means that the number is the address of a customer conforming to the local public network. p0, p1, p2, p3, p4, p5, p6 and p7 are private numbering plans, with a type of number zero to seven. casUnknown means any number received from a Channel Associated Signalling (CAS) trunk. Description of bits: unknown(0) international(1) national(2) subscriber(3) p0(4) p1(5) p2(6) p3(7) p4(8) p5(9) p6(10) p7(11) casUnknown(12)
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

mscVRouteHuntingAlgorithm 1.3.6.1.4.1.562.36.2.1.116.10.1.9
This attribute specifies the type of hunting algorithm that should be used by the VoiceRoute and VoiceSubroutes when selecting a channel to make an outgoing call. bottomUpLinear means that a call from the subnet will be passed to the lowest instance of the VoiceSubroutes, which in turn will pass the call to the lowest instance of SwitchedVoiceService. If there are no available SwitchedVoiceServices in that VoiceSubroute then the process will be repeated for the next lowest instance of VoiceSubroute. topDownLinear means that a call from the subnet will be passed to the highest instance of the VoiceSubroutes, which in turn will pass the call to the highest instance of SwitchedVoiceService. If there are no available SwitchedVoiceServices in that VoiceSubroute then the process will be repeated for the next highest instance of VoiceSubroute.
OBJECT-TYPE    
  INTEGER bottomUpLinear(0), topDownLinear(1)  

mscVRouteMinimumDigitsToRoute 1.3.6.1.4.1.562.36.2.1.116.10.1.10
This attribute specifies the number of digits that must be received before an address resolution request will be sent to the VoiceNetworkingCallServer. Once this level has been exceeded an address resolution request will be sent for every digit received until the dialled number has been resolved in the database. This number should be set to a value which represents the average number of digits that will allow for a unique end-point to be identified. If the number is set too low, then the number of simultaneous calls that can be handled by the VoiceNetworkingCallServer will be reduced since the number of address resolution requests sent for each call will be increased. If it is set too high then address resolution request messages will not be sent to the VoiceNetworkingCallServer until the end-of-dial timer has expired (approximately 12 seconds after the last digit has been received). This can result in very long call setup times.
OBJECT-TYPE    
  Unsigned32 1..16  

mscVRouteVoiceNetworkingCallServer 1.3.6.1.4.1.562.36.2.1.116.10.1.11
This attribute specifies which Vncs instance should be used by all calls into this VoiceRoute from the PBX.
OBJECT-TYPE    
  Link  

mscVRouteOverrideDirectoryNumber 1.3.6.1.4.1.562.36.2.1.116.10.1.12
The number specified here will be used in place of the dialled number to lookup the destination in the VoiceNetworkingCallServer. A null string means that the routing decision should be based on the dialled number. The numbering plan type that will be used will be noAccessCode.
OBJECT-TYPE    
  DigitString SIZE(0..24)  

mscVRoutePrivateNetworkIdentifer 1.3.6.1.4.1.562.36.2.1.116.10.1.13
This attribute specifies the private network identifier (PNI) value. If the value is zero then connectionless supplementary service transport for TCAP formatted FACILITY messages is not supported.
OBJECT-TYPE    
  Unsigned32 0..32700  

mscVRouteCidDataTable 1.3.6.1.4.1.562.36.2.1.116.11
This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteCidDataEntry

mscVRouteCidDataEntry 1.3.6.1.4.1.562.36.2.1.116.11.1
An entry in the mscVRouteCidDataTable.
OBJECT-TYPE    
  MscVRouteCidDataEntry  

mscVRouteCustomerIdentifier 1.3.6.1.4.1.562.36.2.1.116.11.1.1
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
OBJECT-TYPE    
  Unsigned32 0 | 1..8191  

mscVRouteIfEntryTable 1.3.6.1.4.1.562.36.2.1.116.12
This group contains the provisionable attributes for the ifEntry.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteIfEntryEntry

mscVRouteIfEntryEntry 1.3.6.1.4.1.562.36.2.1.116.12.1
An entry in the mscVRouteIfEntryTable.
OBJECT-TYPE    
  MscVRouteIfEntryEntry  

mscVRouteIfAdminStatus 1.3.6.1.4.1.562.36.2.1.116.12.1.1
The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mscVRouteIfIndex 1.3.6.1.4.1.562.36.2.1.116.12.1.2
This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
OBJECT-TYPE    
  InterfaceIndex 1..65535  

mscVRouteStateTable 1.3.6.1.4.1.562.36.2.1.116.13
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteStateEntry

mscVRouteStateEntry 1.3.6.1.4.1.562.36.2.1.116.13.1
An entry in the mscVRouteStateTable.
OBJECT-TYPE    
  MscVRouteStateEntry  

mscVRouteAdminState 1.3.6.1.4.1.562.36.2.1.116.13.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscVRouteOperationalState 1.3.6.1.4.1.562.36.2.1.116.13.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscVRouteUsageState 1.3.6.1.4.1.562.36.2.1.116.13.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscVRouteOperStatusTable 1.3.6.1.4.1.562.36.2.1.116.14
This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteOperStatusEntry

mscVRouteOperStatusEntry 1.3.6.1.4.1.562.36.2.1.116.14.1
An entry in the mscVRouteOperStatusTable.
OBJECT-TYPE    
  MscVRouteOperStatusEntry  

mscVRouteSnmpOperStatus 1.3.6.1.4.1.562.36.2.1.116.14.1.1
The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mscVRouteStatsTable 1.3.6.1.4.1.562.36.2.1.116.15
This group provides the operational attributes for the VoiceRoute component. It contains information relating to calls that originate from the network.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteStatsEntry

mscVRouteStatsEntry 1.3.6.1.4.1.562.36.2.1.116.15.1
An entry in the mscVRouteStatsTable.
OBJECT-TYPE    
  MscVRouteStatsEntry  

mscVRouteTotalCallsFromSubnet 1.3.6.1.4.1.562.36.2.1.116.15.1.1
This attribute counts the total number of calls that have been received from the Passport subnet, including calls that fail. The value wraps to zero when it reaches its maximum.
OBJECT-TYPE    
  Counter32  

mscVRouteCallsClearedNoChannel 1.3.6.1.4.1.562.36.2.1.116.15.1.2
This attribute counts the total number of calls from the subnet that were rejected when all of the in-service channels were busy. When a call is rejected for this reason, the cause code sent to the originator is 34, no circuit/channel available. The value wraps to zero when it reaches its maximum.
OBJECT-TYPE    
  Counter32  

mscVRouteCallsClearedOutOfService 1.3.6.1.4.1.562.36.2.1.116.15.1.3
This attribute counts the total number of calls from the subnet that were rejected because all of the channels were out-of-service. A channel is considered out-of-service if it is unavailable for any reason other than it is being engaged in handling a call. That is, an operator lock of any of the components required for the channel's operation, or problems which interfere with the connection to the PBX, will cause the channel to be considered out-of-service. When a call is rejected for this reason, the cause code sent back to the originator is 27, destination out-of-service. The value wraps to zero when it reaches its maximum.
OBJECT-TYPE    
  Counter32  

mscVRouteCallsRejected 1.3.6.1.4.1.562.36.2.1.116.15.1.4
This attribute counts the total number of calls from the subnet that were rejected because they were: 1) voice calls to a typeOfRoute which is set to data, 2) data calls to a typeOfRoute which is set to voice, 3) using a signalling protocol which is incompatible with this end. The value wraps to zero when it reaches its maximum.
OBJECT-TYPE    
  Counter32  

mscVRouteSubroutesTable 1.3.6.1.4.1.562.36.2.1.116.309
This attribute specifies all of the VoiceSubroutes which are associated with this VoiceRoute. There are only 4 VoiceSubroutes allowed per VoiceRoute.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteSubroutesEntry

mscVRouteSubroutesEntry 1.3.6.1.4.1.562.36.2.1.116.309.1
An entry in the mscVRouteSubroutesTable.
OBJECT-TYPE    
  MscVRouteSubroutesEntry  

mscVRouteSubroutesValue 1.3.6.1.4.1.562.36.2.1.116.309.1.1
This variable represents both the value and the index for the mscVRouteSubroutesTable.
OBJECT-TYPE    
  Link  

mscVRouteSubroutesRowStatus 1.3.6.1.4.1.562.36.2.1.116.309.1.2
This variable is used to control the addition and deletion of individual values of the mscVRouteSubroutesTable.
OBJECT-TYPE    
  RowStatus  

mscVRouteDegradedSubroutesTable 1.3.6.1.4.1.562.36.2.1.116.310
This attribute indicates all of the VoiceSubroutes that have at least one SwitchedVoiceService whose operationalState is disabled.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVRouteDegradedSubroutesEntry

mscVRouteDegradedSubroutesEntry 1.3.6.1.4.1.562.36.2.1.116.310.1
An entry in the mscVRouteDegradedSubroutesTable.
OBJECT-TYPE    
  MscVRouteDegradedSubroutesEntry  

mscVRouteDegradedSubroutesValue 1.3.6.1.4.1.562.36.2.1.116.310.1.1
This variable represents both the value and the index for the mscVRouteDegradedSubroutesTable.
OBJECT-TYPE    
  RowPointer  

mscVsr 1.3.6.1.4.1.562.36.2.1.117
OBJECT IDENTIFIER    

mscVsrRowStatusTable 1.3.6.1.4.1.562.36.2.1.117.1
This entry controls the addition and deletion of mscVsr components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrRowStatusEntry

mscVsrRowStatusEntry 1.3.6.1.4.1.562.36.2.1.117.1.1
A single entry in the table represents a single mscVsr component.
OBJECT-TYPE    
  MscVsrRowStatusEntry  

mscVsrRowStatus 1.3.6.1.4.1.562.36.2.1.117.1.1.1
This variable is used as the basis for SNMP naming of mscVsr components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscVsrComponentName 1.3.6.1.4.1.562.36.2.1.117.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscVsrStorageType 1.3.6.1.4.1.562.36.2.1.117.1.1.4
This variable represents the storage type value for the mscVsr tables.
OBJECT-TYPE    
  StorageType  

mscVsrIndex 1.3.6.1.4.1.562.36.2.1.117.1.1.10
This variable represents the index for the mscVsr tables.
OBJECT-TYPE    
  Integer32 1..255  

mscVsrSvs 1.3.6.1.4.1.562.36.2.1.117.2
OBJECT IDENTIFIER    

mscVsrSvsRowStatusTable 1.3.6.1.4.1.562.36.2.1.117.2.1
This entry controls the addition and deletion of mscVsrSvs components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsRowStatusEntry

mscVsrSvsRowStatusEntry 1.3.6.1.4.1.562.36.2.1.117.2.1.1
A single entry in the table represents a single mscVsrSvs component.
OBJECT-TYPE    
  MscVsrSvsRowStatusEntry  

mscVsrSvsRowStatus 1.3.6.1.4.1.562.36.2.1.117.2.1.1.1
This variable is used as the basis for SNMP naming of mscVsrSvs components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscVsrSvsComponentName 1.3.6.1.4.1.562.36.2.1.117.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscVsrSvsStorageType 1.3.6.1.4.1.562.36.2.1.117.2.1.1.4
This variable represents the storage type value for the mscVsrSvs tables.
OBJECT-TYPE    
  StorageType  

mscVsrSvsIndex 1.3.6.1.4.1.562.36.2.1.117.2.1.1.10
This variable represents the index for the mscVsrSvs tables.
OBJECT-TYPE    
  Integer32 1..32  

mscVsrSvsFramer 1.3.6.1.4.1.562.36.2.1.117.2.2
OBJECT IDENTIFIER    

mscVsrSvsFramerRowStatusTable 1.3.6.1.4.1.562.36.2.1.117.2.2.1
This entry controls the addition and deletion of mscVsrSvsFramer components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsFramerRowStatusEntry

mscVsrSvsFramerRowStatusEntry 1.3.6.1.4.1.562.36.2.1.117.2.2.1.1
A single entry in the table represents a single mscVsrSvsFramer component.
OBJECT-TYPE    
  MscVsrSvsFramerRowStatusEntry  

mscVsrSvsFramerRowStatus 1.3.6.1.4.1.562.36.2.1.117.2.2.1.1.1
This variable is used as the basis for SNMP naming of mscVsrSvsFramer components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscVsrSvsFramerComponentName 1.3.6.1.4.1.562.36.2.1.117.2.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscVsrSvsFramerStorageType 1.3.6.1.4.1.562.36.2.1.117.2.2.1.1.4
This variable represents the storage type value for the mscVsrSvsFramer tables.
OBJECT-TYPE    
  StorageType  

mscVsrSvsFramerIndex 1.3.6.1.4.1.562.36.2.1.117.2.2.1.1.10
This variable represents the index for the mscVsrSvsFramer tables.
OBJECT-TYPE    
  NonReplicated  

mscVsrSvsFramerVfpDebug 1.3.6.1.4.1.562.36.2.1.117.2.2.5
OBJECT IDENTIFIER    

mscVsrSvsFramerVfpDebugRowStatusTable 1.3.6.1.4.1.562.36.2.1.117.2.2.5.1
This entry controls the addition and deletion of mscVsrSvsFramerVfpDebug components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsFramerVfpDebugRowStatusEntry

mscVsrSvsFramerVfpDebugRowStatusEntry 1.3.6.1.4.1.562.36.2.1.117.2.2.5.1.1
A single entry in the table represents a single mscVsrSvsFramerVfpDebug component.
OBJECT-TYPE    
  MscVsrSvsFramerVfpDebugRowStatusEntry  

mscVsrSvsFramerVfpDebugRowStatus 1.3.6.1.4.1.562.36.2.1.117.2.2.5.1.1.1
This variable is used as the basis for SNMP naming of mscVsrSvsFramerVfpDebug components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscVsrSvsFramerVfpDebugComponentName 1.3.6.1.4.1.562.36.2.1.117.2.2.5.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscVsrSvsFramerVfpDebugStorageType 1.3.6.1.4.1.562.36.2.1.117.2.2.5.1.1.4
This variable represents the storage type value for the mscVsrSvsFramerVfpDebug tables.
OBJECT-TYPE    
  StorageType  

mscVsrSvsFramerVfpDebugIndex 1.3.6.1.4.1.562.36.2.1.117.2.2.5.1.1.10
This variable represents the index for the mscVsrSvsFramerVfpDebug tables.
OBJECT-TYPE    
  NonReplicated  

mscVsrSvsFramerMvpDebug 1.3.6.1.4.1.562.36.2.1.117.2.2.6
OBJECT IDENTIFIER    

mscVsrSvsFramerMvpDebugRowStatusTable 1.3.6.1.4.1.562.36.2.1.117.2.2.6.1
This entry controls the addition and deletion of mscVsrSvsFramerMvpDebug components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsFramerMvpDebugRowStatusEntry

mscVsrSvsFramerMvpDebugRowStatusEntry 1.3.6.1.4.1.562.36.2.1.117.2.2.6.1.1
A single entry in the table represents a single mscVsrSvsFramerMvpDebug component.
OBJECT-TYPE    
  MscVsrSvsFramerMvpDebugRowStatusEntry  

mscVsrSvsFramerMvpDebugRowStatus 1.3.6.1.4.1.562.36.2.1.117.2.2.6.1.1.1
This variable is used as the basis for SNMP naming of mscVsrSvsFramerMvpDebug components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscVsrSvsFramerMvpDebugComponentName 1.3.6.1.4.1.562.36.2.1.117.2.2.6.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscVsrSvsFramerMvpDebugStorageType 1.3.6.1.4.1.562.36.2.1.117.2.2.6.1.1.4
This variable represents the storage type value for the mscVsrSvsFramerMvpDebug tables.
OBJECT-TYPE    
  StorageType  

mscVsrSvsFramerMvpDebugIndex 1.3.6.1.4.1.562.36.2.1.117.2.2.6.1.1.10
This variable represents the index for the mscVsrSvsFramerMvpDebug tables.
OBJECT-TYPE    
  NonReplicated  

mscVsrSvsFramerPcmCapture 1.3.6.1.4.1.562.36.2.1.117.2.2.7
OBJECT IDENTIFIER    

mscVsrSvsFramerPcmCaptureRowStatusTable 1.3.6.1.4.1.562.36.2.1.117.2.2.7.1
This entry controls the addition and deletion of mscVsrSvsFramerPcmCapture components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsFramerPcmCaptureRowStatusEntry

mscVsrSvsFramerPcmCaptureRowStatusEntry 1.3.6.1.4.1.562.36.2.1.117.2.2.7.1.1
A single entry in the table represents a single mscVsrSvsFramerPcmCapture component.
OBJECT-TYPE    
  MscVsrSvsFramerPcmCaptureRowStatusEntry  

mscVsrSvsFramerPcmCaptureRowStatus 1.3.6.1.4.1.562.36.2.1.117.2.2.7.1.1.1
This variable is used as the basis for SNMP naming of mscVsrSvsFramerPcmCapture components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscVsrSvsFramerPcmCaptureComponentName 1.3.6.1.4.1.562.36.2.1.117.2.2.7.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscVsrSvsFramerPcmCaptureStorageType 1.3.6.1.4.1.562.36.2.1.117.2.2.7.1.1.4
This variable represents the storage type value for the mscVsrSvsFramerPcmCapture tables.
OBJECT-TYPE    
  StorageType  

mscVsrSvsFramerPcmCaptureIndex 1.3.6.1.4.1.562.36.2.1.117.2.2.7.1.1.10
This variable represents the index for the mscVsrSvsFramerPcmCapture tables.
OBJECT-TYPE    
  NonReplicated  

mscVsrSvsFramerProvTable 1.3.6.1.4.1.562.36.2.1.117.2.2.10
This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisionable Framer groups.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsFramerProvEntry

mscVsrSvsFramerProvEntry 1.3.6.1.4.1.562.36.2.1.117.2.2.10.1
An entry in the mscVsrSvsFramerProvTable.
OBJECT-TYPE    
  MscVsrSvsFramerProvEntry  

mscVsrSvsFramerInterfaceName 1.3.6.1.4.1.562.36.2.1.117.2.2.10.1.1
This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.
OBJECT-TYPE    
  Link  

mscVsrSvsFramerStateTable 1.3.6.1.4.1.562.36.2.1.117.2.2.14
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsFramerStateEntry

mscVsrSvsFramerStateEntry 1.3.6.1.4.1.562.36.2.1.117.2.2.14.1
An entry in the mscVsrSvsFramerStateTable.
OBJECT-TYPE    
  MscVsrSvsFramerStateEntry  

mscVsrSvsFramerAdminState 1.3.6.1.4.1.562.36.2.1.117.2.2.14.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscVsrSvsFramerOperationalState 1.3.6.1.4.1.562.36.2.1.117.2.2.14.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscVsrSvsFramerUsageState 1.3.6.1.4.1.562.36.2.1.117.2.2.14.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscVsrSvsFramerStatsTable 1.3.6.1.4.1.562.36.2.1.117.2.2.15
This group contains the operational statistics data for a Framer component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsFramerStatsEntry

mscVsrSvsFramerStatsEntry 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1
An entry in the mscVsrSvsFramerStatsTable.
OBJECT-TYPE    
  MscVsrSvsFramerStatsEntry  

mscVsrSvsFramerTotalCells 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1.1
This attribute counts the total number of cells received from the interface. Each cell contains 44 bytes of data from the DS0 channel. Since a DS0 provides data at 64 kbit/s, each cell contains 5.5 ms of audio data. This data flow is measured before compression is performed on the channel. This counter wraps to zero after reaching its maximum value.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscVsrSvsFramerAudioCells 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1.2
This attribute counts the total number of cells containing audio data received from the interface while the channel was seized. A CCS channel is always considered to be seized. Audio data includes cells containing voice as well modem audio, but not silence. A cell contains 44 bytes of data from the DS0 channel(5.5 ms). This flow is measured before compression is performed on the channel. This counter wraps to zero after reaching its maximum value.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscVsrSvsFramerSilenceCells 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1.4
This attribute counts the total number of cells containing silence data received from the interface which was not forwarded into the network, thus saving bandwidth. A channel may go into silence due to the operation of the silence suppression feature or for CAS channels when the ABCD signalling bits go idle. A cell contains 44 bytes of data from the DS0 channel(5.5 ms). This flow is measured before compression is performed on the channel. This counter wraps to zero after reaching its maximum value.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscVsrSvsFramerModemCells 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1.5
This attribute is migrated into modemFaxCells.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscVsrSvsFramerCurrentEncodingRate 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1.6
This attribute has been migrated to currentRate in Operational group.
OBJECT-TYPE    
  INTEGER n640(1), n320(2), n240(3), n160(4), n80(5), n144(6), n120(7), n96(8), n72(9), n63(10), n53(11), n48(12), n24(13), n12(14), n03(15)  

mscVsrSvsFramerLrcErrors 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1.7
This attribute counts the number of frames received from the network with LRC errors.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscVsrSvsFramerFrmLostInNetwork 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1.8
This attribute counts the number of frames which the service knows it did not receive from the network although they were sent in to the network from the far end.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscVsrSvsFramerFrmUnderRuns 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1.9
This attribute counts the number of times that a frame was needed but was not available because it had been delayed too long in the network. This error may occur repeatedly if the interface clocks at the two access points to the network are operating at different rates.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscVsrSvsFramerFrmDumped 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1.10
This attribute counts the number of frames which have been dumped because the output queue grew too large. This can occur if the clock rate on the incoming interface is faster than the clock rate on the outgoing interface and there are no silence periods to absorb the difference, or when a compression rate change occurs. This count wraps to zero after reaching its maximum value.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscVsrSvsFramerModemSilenceCells 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1.26
This attribute is migrated into faxIdleCells.
OBJECT-TYPE    
  Counter32  

mscVsrSvsFramerCurrentEncoding 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1.27
This attribute has been migrated to currentEncoding in Operational group.
OBJECT-TYPE    
  INTEGER g729(1), g728(2), g723(3), g726(4), g711(5), v22(32), v22bis(33), faxRelay(64), v27(65), v29(66), v17(67), none(255)  

mscVsrSvsFramerTptStatus 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1.28
This attribute has been migrated to tptStatus in Operational group.
OBJECT-TYPE    
  INTEGER operating(0), rejected(1), monitoring(2), disabled(3)  

mscVsrSvsFramerFaxRelayCells 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1.35
This attribute counts the total number of fax relay cells sent to the network. This counter wraps to zero after reaching its maximum value.
OBJECT-TYPE    
  Counter32  

mscVsrSvsFramerModemFaxCells 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1.36
This attribute counts the total number of cells containing modem data received from the interface while the channel was seized. A CCS channel is always considered to be seized. Cells are considered to be modem data if a constant energy level above -25 dBmO is detected for more than 900 ms. An energy level below -36 dBmO for more than 650 ms is required to detect that the modem is no longer present. A cell contains 44 bytes of data from the DS0 channel (5.5 ms). This flow is measured before compression is performed on the channel. This counter wraps to zero after reaching its maximum value.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscVsrSvsFramerFaxIdleCells 1.3.6.1.4.1.562.36.2.1.117.2.2.15.1.37
This attribute counts the total number of cells containing silent fax data received from the interface which were not forwarded into the network, thus saving bandwidth. A channel may go into silence due to the silence Suppression feature or for CAS channels when the ABCD signalling bits go idle. A cell contains 44 bytes of data from the DS0 channel (5.5 ms). This flow is measured before compression is performed on the channel. This counter wraps to zero after reaching its maximum value.
OBJECT-TYPE    
  Counter32  

mscVsrSvsFramerOperTable 1.3.6.1.4.1.562.36.2.1.117.2.2.16
This group contains the operational data for a Svs Framer.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsFramerOperEntry

mscVsrSvsFramerOperEntry 1.3.6.1.4.1.562.36.2.1.117.2.2.16.1
An entry in the mscVsrSvsFramerOperTable.
OBJECT-TYPE    
  MscVsrSvsFramerOperEntry  

mscVsrSvsFramerOpCurrentEncoding 1.3.6.1.4.1.562.36.2.1.117.2.2.16.1.1
This attribute indicates the encoding currently being performed on this channel. g711 indicates that pulse code modulation (PCM) defined by ITU-T G.711 is being performed. g726 indicates that adaptive differential pulse code modulation (ADPCM) defined by ITU-T G.726 is being performed. g728 indicates that the Low Delay Coded Excited Linear Predictive Coder (LD-CELP) algorithm defined by ITU-T G.728 is being performed. g729 indicates that the Conjunctive Structure Algebraic Code Excited Linear Predictive Coder (CS-ACELP) algorithm defined by ITU-T G.729 is being performed. v27 indicates that the algorithm defined by ITU-T V.27 is being performed. v29 indicates that the algorithm defined by ITU-T V.29 is being performed.
OBJECT-TYPE    
  INTEGER g729(1), g728(2), g723(3), g726(4), g711(5), v22(32), v22bis(33), faxRelay(64), v27(65), v29(66), v17(67), none(255)  

mscVsrSvsFramerCurrentRate 1.3.6.1.4.1.562.36.2.1.117.2.2.16.1.2
This attribute indicates the current encoding rate for frames being sent to the network.
OBJECT-TYPE    
  INTEGER n0(0), n640(1), n320(2), n240(3), n160(4), n80(5), n144(6), n120(7), n96(8), n72(9), n63(10), n53(11), n48(12), n24(13), n12(14), n03(15)  

mscVsrSvsFramerOpTptStatus 1.3.6.1.4.1.562.36.2.1.117.2.2.16.1.3
This attribute indicates the current status of the tandem pass through algorithm. If tptStatus is operating, the tandem pass through algorithm is cutting through a voice switch. If tptStatus is monitoring, negotiatedTandemPassThrough is enabled, but the tandem pass through algorithm is not cutting through a voice switch. If tptStatus is disabled, negotiatedTandemPassThrough is disabled.
OBJECT-TYPE    
  INTEGER operating(0), monitoring(2), disabled(3)  

mscVsrSvsFramerNegTable 1.3.6.1.4.1.562.36.2.1.117.2.2.17
This group contains the attributes indicating the results of voice networking end to end negotiation.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsFramerNegEntry

mscVsrSvsFramerNegEntry 1.3.6.1.4.1.562.36.2.1.117.2.2.17.1
An entry in the mscVsrSvsFramerNegTable.
OBJECT-TYPE    
  MscVsrSvsFramerNegEntry  

mscVsrSvsFramerNegotiatedSilenceSuppression 1.3.6.1.4.1.562.36.2.1.117.2.2.17.1.1
This attribute indicates the result of negotiating silence suppression with the remote end across the subnet. The parameter used for negotiating with the remote end is provisioned in Vncs Vp silenceSuppression. If negotiatedSilenceSuppression is off, silence suppression is never performed. If negotiatedSilenceSuppression is on, silence suppression is always performed. If negotiatedSilenceSuppression is congested, silence suppression is performed only when the network is congested. If negotiatedSilenceSuppression is slow, silence suppression begins after 10 to 20 seconds without any speech or audio being detected. If negotiatedSilenceSuppression is slowAndCongested, both the slow and congested options are applied.
OBJECT-TYPE    
  INTEGER off(0), on(1), congested(2), slow(3), slowAndCongested(4)  

mscVsrSvsFramerNegotiatedFisG711G726 1.3.6.1.4.1.562.36.2.1.117.2.2.17.1.2
This attribute indicates the result of negotiating G.711/G.726 fax idle suppression with the remote end across the subnet. The parameter used for negotiating with the remote end is provisioned in Vncs Vp faxIdleSuppressionG711G726.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscVsrSvsFramerNegotiatedDtmfRegeneration 1.3.6.1.4.1.562.36.2.1.117.2.2.17.1.3
This attribute indicates the result of negotiating DTMF regeneration with the remote end across the subnet. The parameter used for negotiating with the remote end is provisioned in Vncs Vp dtmfRegeneration. If negotiatedDtmfRegeneration is on, DTMF tones received from the link are first converted to digits before being sent to the subnet. When a digit is received from the subnet, its respective DTMF tone is generated before being sent to the link. If negotiatedDtmfRegeneration is off, DTMF tones are transported transparently.
OBJECT-TYPE    
  INTEGER off(0), on(1)  

mscVsrSvsFramerNegotiatedV17AsG711G726 1.3.6.1.4.1.562.36.2.1.117.2.2.17.1.4
This attribute indicates how this SwitchedVoiceService negotiates with V.17 fax machines, as determined by negotiation with the remote end across the subnet. The parameter used for negotiating with the remote end is provisioned in Vncs Vp v17EncodedAsG711G726. If negotiatedV17AsG711G726 is no, V.17 fax machines are instructed to use V.29, and V.29 fax traffic sent by fax machines is demodulated and encoded using fax relay. If negotiatedV17AsG711G726 is yes, V.17 fax machines are permitted to use V.17 and V.17 fax traffic sent by fax machines is encoded using G.711 or G.726, at the rates given in negotiatedRates.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mscVsrSvsFramerNegotiatedTandemPassThrough 1.3.6.1.4.1.562.36.2.1.117.2.2.17.1.5
This attribute indicates the result of negotiating tandem pass through with the remote end across the subnet. The parameter used for negotiating with the remote end is provisioned in Vncs Vp tandemPassThrough.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscVsrSvsFramerFrmToNetworkTable 1.3.6.1.4.1.562.36.2.1.117.2.2.315
This attribute counts the number of frames sent to the network at each encoding rate. Fax relay cells are not included.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsFramerFrmToNetworkEntry

mscVsrSvsFramerFrmToNetworkEntry 1.3.6.1.4.1.562.36.2.1.117.2.2.315.1
An entry in the mscVsrSvsFramerFrmToNetworkTable.
OBJECT-TYPE    
  MscVsrSvsFramerFrmToNetworkEntry  

mscVsrSvsFramerFrmToNetworkIndex 1.3.6.1.4.1.562.36.2.1.117.2.2.315.1.1
This variable represents the mscVsrSvsFramerFrmToNetworkTable specific index for the mscVsrSvsFramerFrmToNetworkTable.
OBJECT-TYPE    
  INTEGER n64KbitS(0), n32KbitS(1), n24KbitS(2), n16KbitS(3), n8KbitS(4)  

mscVsrSvsFramerFrmToNetworkValue 1.3.6.1.4.1.562.36.2.1.117.2.2.315.1.2
This variable represents an individual value for the mscVsrSvsFramerFrmToNetworkTable.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscVsrSvsFramerFrmFromNetworkTable 1.3.6.1.4.1.562.36.2.1.117.2.2.316
This attribute counts the number of frames received from the network at each encoding rate.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsFramerFrmFromNetworkEntry

mscVsrSvsFramerFrmFromNetworkEntry 1.3.6.1.4.1.562.36.2.1.117.2.2.316.1
An entry in the mscVsrSvsFramerFrmFromNetworkTable.
OBJECT-TYPE    
  MscVsrSvsFramerFrmFromNetworkEntry  

mscVsrSvsFramerFrmFromNetworkIndex 1.3.6.1.4.1.562.36.2.1.117.2.2.316.1.1
This variable represents the mscVsrSvsFramerFrmFromNetworkTable specific index for the mscVsrSvsFramerFrmFromNetworkTable.
OBJECT-TYPE    
  INTEGER n64KbitS(0), n32KbitS(1), n24KbitS(2), n16KbitS(3), n8KbitS(4)  

mscVsrSvsFramerFrmFromNetworkValue 1.3.6.1.4.1.562.36.2.1.117.2.2.316.1.2
This variable represents an individual value for the mscVsrSvsFramerFrmFromNetworkTable.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscVsrSvsFramerNEncodingTable 1.3.6.1.4.1.562.36.2.1.117.2.2.467
This attribute indicates the results of negotiating audio call encodings for voice, modemFax and fax traffic with the remote end across the subnet. The parameters used for negotiating with the remote end are provisioned in Vncs Vp voiceEncodingChoice and Vncs Vp modemFaxEncodingChoice. voice traffic is all traffic from the start of a call or speech until a 2100 Hz tone or call release. modemFax traffic is all traffic after a 2100 Hz tone but before a fax preamble, speech or call release. fax traffic is all traffic after a fax preamble but before speech or call release. g711 indicates that pulse code modulation (PCM) defined by ITU-T G.711 is the negotiated encoding. g726 indicates that Adaptive Differential Pulse Code Modulation (ADPCM) defined by ITU-T G.726 is the negotiated encoding. g711G726 indicates that pulse code modulation (PCM) defined by ITU-T G.711 and Adaptive Differential Pulse Code Modulation (ADPCM) defined by ITU-T G.726 are both negotiated encodings. If negotiatedEncoding is g711G726, the actual encoding performed can be either G.711 or G.726, depending on network congestion. g728 indicates that Low Delay Coded Excited Linear Predictive Coder (CS-ACELP) defined by ITU-T G.728 is the negotiated encoding. g729 indicates that Conjunctive Structure Algebraic Code Excited Linear Predictive Coder (CS-ACELP) defined by ITU-T G.729 is the negotiated encoding. v29V27Relay indicates that fax relay using ITU-T V.29 or ITU-T V.27 is the negotiated encoding. v17V29V27Relay indicates that fax relay using ITU-T V.17, ITU-T V.29, or ITU-T V.27 is the negotiated encoding. If all negotiated encodings are none, the negotiation of audio call encodings is not complete.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsFramerNEncodingEntry

mscVsrSvsFramerNEncodingEntry 1.3.6.1.4.1.562.36.2.1.117.2.2.467.1
An entry in the mscVsrSvsFramerNEncodingTable.
OBJECT-TYPE    
  MscVsrSvsFramerNEncodingEntry  

mscVsrSvsFramerNEncodingIndex 1.3.6.1.4.1.562.36.2.1.117.2.2.467.1.1
This variable represents the mscVsrSvsFramerNEncodingTable specific index for the mscVsrSvsFramerNEncodingTable.
OBJECT-TYPE    
  INTEGER voice(0), modemFax(1), fax(2)  

mscVsrSvsFramerNEncodingValue 1.3.6.1.4.1.562.36.2.1.117.2.2.467.1.2
This variable represents an individual value for the mscVsrSvsFramerNEncodingTable.
OBJECT-TYPE    
  INTEGER g729(1), g728(2), g726(4), g711(5), g711G726(31), v29V27Relay(64), v17V29V27Relay(68), none(255)  

mscVsrSvsFramerNRatesTable 1.3.6.1.4.1.562.36.2.1.117.2.2.479
This attribute indicates the results of negotiating minimum and maximum rates for voice, modemFax and fax traffic with the remote end across the subnet. The parameters used for negotiating with the remote end are provisioned in Vncs Vp voiceRates and Vncs Vp modemFaxRates.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsFramerNRatesEntry

mscVsrSvsFramerNRatesEntry 1.3.6.1.4.1.562.36.2.1.117.2.2.479.1
An entry in the mscVsrSvsFramerNRatesTable.
OBJECT-TYPE    
  MscVsrSvsFramerNRatesEntry  

mscVsrSvsFramerNRatesTrafficIndex 1.3.6.1.4.1.562.36.2.1.117.2.2.479.1.1
This variable represents the next to last index for the mscVsrSvsFramerNRatesTable.
OBJECT-TYPE    
  INTEGER voice(0), modemFax(1), fax(2)  

mscVsrSvsFramerNRatesRateIndex 1.3.6.1.4.1.562.36.2.1.117.2.2.479.1.2
This variable represents the final index for the mscVsrSvsFramerNRatesTable.
OBJECT-TYPE    
  INTEGER min(0), max(1)  

mscVsrSvsFramerNRatesValue 1.3.6.1.4.1.562.36.2.1.117.2.2.479.1.3
This variable represents an individual value for the mscVsrSvsFramerNRatesTable.
OBJECT-TYPE    
  INTEGER n00(0), n03(1), n12(2), n24(3), n48(4), n72(5), n96(6), n120(7), n144(8), n80(66), n160(67), n240(68), n320(69), n640(70)  

mscVsrSvsLCo 1.3.6.1.4.1.562.36.2.1.117.2.3
OBJECT IDENTIFIER    

mscVsrSvsLCoRowStatusTable 1.3.6.1.4.1.562.36.2.1.117.2.3.1
This entry controls the addition and deletion of mscVsrSvsLCo components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsLCoRowStatusEntry

mscVsrSvsLCoRowStatusEntry 1.3.6.1.4.1.562.36.2.1.117.2.3.1.1
A single entry in the table represents a single mscVsrSvsLCo component.
OBJECT-TYPE    
  MscVsrSvsLCoRowStatusEntry  

mscVsrSvsLCoRowStatus 1.3.6.1.4.1.562.36.2.1.117.2.3.1.1.1
This variable is used as the basis for SNMP naming of mscVsrSvsLCo components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscVsrSvsLCoComponentName 1.3.6.1.4.1.562.36.2.1.117.2.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscVsrSvsLCoStorageType 1.3.6.1.4.1.562.36.2.1.117.2.3.1.1.4
This variable represents the storage type value for the mscVsrSvsLCo tables.
OBJECT-TYPE    
  StorageType  

mscVsrSvsLCoIndex 1.3.6.1.4.1.562.36.2.1.117.2.3.1.1.10
This variable represents the index for the mscVsrSvsLCo tables.
OBJECT-TYPE    
  NonReplicated  

mscVsrSvsLCoPathDataTable 1.3.6.1.4.1.562.36.2.1.117.2.3.10
This group contains all operational attributes for the path oriented LCo.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsLCoPathDataEntry

mscVsrSvsLCoPathDataEntry 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1
An entry in the mscVsrSvsLCoPathDataTable.
OBJECT-TYPE    
  MscVsrSvsLCoPathDataEntry  

mscVsrSvsLCoState 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.1
This attribute reflects the current state of the connection. The pathDown state indicates a connection that has no remote end provisioned or the application has not yet signalled for a path. The selectingRoute state occurs when a request has been sent to route selector and it has not yet responded. The connectingState occurs while a path is being established. The pathUp state is the normal operational state of a path. The pathDownRetrying state indicates a path that attempted route selection but received no route and is now waiting to retry route selection again.
OBJECT-TYPE    
  INTEGER pathDown(0), selectingRoute(1), connecting(2), pathUp(3), pathDownRetrying(4)  

mscVsrSvsLCoOverrideRemoteName 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.2
If set and the current PLC remoteName is blank this remoteName will override the blank PLC remoteName. Usually you would set this attribute and then lock/unlock the service component which will result in this new overrideRemoteName being used as if it had been provisioned into the PLC remoteName. The advantage of this attribute is that the connection's remoteName can be changed immediately without having to 'activate prov' but the disadvantage is that the overrideRemoteName is not permanent and if the card or switch is reset the override will be lost.
OBJECT-TYPE    
  AsciiString SIZE(0..40)  

mscVsrSvsLCoEnd 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.3
This attribute identifies whether this is the calling or called end of the path.
OBJECT-TYPE    
  INTEGER calling(0), called(1)  

mscVsrSvsLCoCostMetric 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.4
This attribute gives the route's total cost metric. It is calculated as the sum of the cost metric of all trunks in the path at the time the connection was established. The cost metric of a trunk is defined by the trunkCost attribute of the Trunk component. The costMetric for an LCo that is originated and terminated on the same module is 0.
OBJECT-TYPE    
  Unsigned32 0..65535  

mscVsrSvsLCoDelayMetric 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.5
This attribute gives the total delay of the route as the one way delay for a 512 byte packet. It is calculated as the sum of the delays of all trunks in the path stored in topology at the time the connection was established. The delay for an LCo that is originated and terminated on the same module is 0.
OBJECT-TYPE    
  Unsigned32 0..100000  

mscVsrSvsLCoRoundTripDelay 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.6
This attribute contains the time taken for a packet (cell) of 44 bytes to be transmitted to the remote LCo and return to this LCo. The number reported is given in milliseconds to the nearest millisecond. A value of one millisecond is reported if the time is less than 1 millisecond even though the delay may be less than 1 Millisecond when the LCo is originated and terminated on the same module.
OBJECT-TYPE    
  Unsigned32 0..200000  

mscVsrSvsLCoSetupPriority 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.7
This attribute gives the priority at which the current path is established. Zero is the highest priority and four is the lowest. The holdingPriority, a complementary attribute of this component, indicates the priority a path maintains once it is established.
OBJECT-TYPE    
  Unsigned32 0..4  

mscVsrSvsLCoHoldingPriority 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.8
This attribute gives the priority at which a path holds its current path once the path is established. Zero is the highest priority and four is the lowest. The setupPriority, a complementary attribute, indicates the priority of a path at establishment time.
OBJECT-TYPE    
  Unsigned32 0..4  

mscVsrSvsLCoRequiredTxBandwidth 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.9
This attribute gives the actual bandwidth (in bits per second) reserved by this path on each of the trunks of its route. This attribute represents the bandwidth for traffic outgoing to the remote end point. The originating end of the connection determines this value.
OBJECT-TYPE    
  Gauge32 0..4294967295  

mscVsrSvsLCoRequiredRxBandwidth 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.10
This attribute gives the actual bandwidth (in bits per second) reserved by this path on each of trunks of its route. This attribute represents the bandwidth for traffic incoming from the remote end point. The originating end of the connection determines this value
OBJECT-TYPE    
  Gauge32 0..4294967295  

mscVsrSvsLCoRequiredTrafficType 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.11
This operational attribute indicates the type of traffic transmitted over the path. There are eight possible traffic types, and the path can transmit only one of them. The originating end of the connection determines the type. These are arbitrary designations for traffic type. The voice, data and video traffic types are defined, and five other arbitrary traffic types can be defined by the network administration. This attribute is used in the route selection process to restrict the route to trunks that support this traffic type. The supportedTrafficType trunk attribute lists all the types of traffic allowed on the trunk. For example, if requiredTrafficType is specified as trafficType1 then only trunks that include trafficType1 in supportedTrafficType, will be candidates for this connection.
OBJECT-TYPE    
  INTEGER voice(0), data(1), video(2), trafficType1(3), trafficType2(4), trafficType3(5), trafficType4(6), trafficType5(7)  

mscVsrSvsLCoPermittedTrunkTypes 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.12
This operational attribute lists up to eight types of trunk that can be used on the route. The originating end of the connection determines the types. The terrestrial and satellite trunk types have been defined, leaving six remaining arbitrary types that can be defined by the network administration. The trunk's type is indicated in the trunkType attribute of the Trunk component. When selecting a route, PORS only chooses trunks whose trunkType are in the permittedTrunkTypes for the path. Description of bits: terrestrial(0) satellite(1) trunkType1(2) trunkType2(3) trunkType3(4) trunkType4(5) trunkType5(6) trunkType6(7)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscVsrSvsLCoRequiredSecurity 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.13
This attribute indicates the required minimum level of security of the trunks on the route. Zero represents the most secure and seven represents the least secure. The trunk's security is indicated by the trunkSecurity attribute of the Trunk component, and has values identical in range and meaning to the requiredSecurity attribute. PORS ensures that any route selected does not contain a trunk whose trunkSecurity attribute is numerically greater than the requiredSecurity.
OBJECT-TYPE    
  Unsigned32 0..7  

mscVsrSvsLCoRequiredCustomerParameter 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.14
This attribute indicates the allowed customer defined parameter of the trunks on the route.The originating end of the connection determines the customer defined parameter. Its value, a number from zero to seven, is chosen by a network administration to have a meaning specific to their network, thus allowing them to customize the use of their trunks. A complementary trunk attribute, customerParameter, also has a value from zero to seven. The route selection process does not consider trunks whose customerParameter is greater than the requiredCustomerParameter of the path.
OBJECT-TYPE    
  Unsigned32 0..7  

mscVsrSvsLCoEmissionPriority 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.15
This attribute indicates the urgency with which packets on the path are emitted by the trunks on the route. The originating end of the connection selects the emissionPriority. EmissionPriority of zero indicates the highest emission priority, while two indicates the lowest emission priority. Packets with a higher emissionPriority (or numerically less) are serviced and sent out before the packets of lower emissionPriority (or numerically higher).
OBJECT-TYPE    
  Unsigned32 0..2  

mscVsrSvsLCoDiscardPriority 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.16
This attribute indicates the importance of the packets on the path.The originating end of the connection sets discardPriority. One is used for paths carrying the most important traffic, and three is used for paths carrying the least important traffic. Packets with lower discardPriority(numerically lower) are discarded after packets with a higher discardPriority(numerically higher).
OBJECT-TYPE    
  Unsigned32 1..3  

mscVsrSvsLCoPathType 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.17
This attribute indicates whether the path for this PLC was determined automatically or by static provisioning. Normal pathTypes are selected automatically by Route Selector.The other pathTypes are both manual pathTypes where the operator must specify, through provisioning, a static route termed the manualPath. A manual pathType connection is nearly identical to a normal path type connection with the exception that the route is pre-provisioned. For a manual pathType, bandwidth reservations are respected along the path exactly as in a normal path. The last type, the forced pathType, is also a manual path but regardless of the bandwidth available the route is granted provided the trunks are operational and there are sufficient Logical Channels (LChs). The forced pathType could result in over committing the reserved bandwidth allowed on a trunk. A better way to achieve the effects of a forced pathType is to use a manual pathType with setupPriority = 0 and holdingPriority = 0. In this manner the path will reserve correct bandwidth and it will bump other paths if required while not being bumped itself.
OBJECT-TYPE    
  INTEGER normal(0), manual(1), forced(2)  

mscVsrSvsLCoRetryCount 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.18
This attribute is the count of the number of times the path chosen during route selection could not be instantiated. This count should be three or below if the network is performing adequately. A high value indicates that the route selection is often performed using an out-of-date view of available network bandwidth and/or topology. This attribute will only increase at the calling end of the connection. This attribute is reset each time a path reconnects and stops counting when it reaches its maximum value.
OBJECT-TYPE    
  Unsigned32 0..255  

mscVsrSvsLCoPathFailureCount 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.19
This attribute is the count of the number of times the path has successfully connected. It is set to zero the first time the path is up. If a path fails anytime after connecting this count will be incremented when the path is up again. Failed route requests do not count in this statistic. See retryCount above. This attribute stops counting at its maximum value.
OBJECT-TYPE    
  Unsigned32 0..65535  

mscVsrSvsLCoReasonForNoRoute 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.20
This attribute is the route selection's reasonForNoRoute and provides a brief reason for which a route was not selected. The reasons are essentially self-explanatory. Perhaps two reasons for no route require some explanation. The reason unknownRemoteNodeName is issued when the remote node name is not in the topological database. The reason plcAttributesNotMet is issued when there is no network connectivity at a level specified by the PLC attributes. This reason is also issued when there is no physical connectivity between two end nodes.
OBJECT-TYPE    
  INTEGER none(0), destinationNameTooLong(1), destinationNotSpecified(2), unknownDestinationName(3), incorrectDestination(4), incorrectDestinationEndPoint(5), unknownSource(6), unknownDestination(7), sameNode(8), routeCostTooMuch(9), routesDelayTooLong(10), attributesNotMet(11), anError(12), attributeProfileProblem(13), manualPathIndexProblem(14)  

mscVsrSvsLCoLastTearDownReason 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.21
This attribute reflects the last tear down reason for a connection (LCo). In many cases this displays the reason for a momentary service interruption. This attribute applies to the last path failure only. If a path is no longer up, this may give an indication to the reason that the path has failed. In many cases an alarm will also be generated with more specific information. The following is a brief description of the reasons: none - This path has no information for the teardown this is typical of a path provisioned with no remoteName that has not been up. normalShutDown - This path has gone down due to normal call termination. insufficientTxLcOrBandwidth - At present there is either no available bandwidth or logical channel numbers available on one or more of the trunks for this path in the transmit direction. insufficientRxLcOrBandwidth - At present there is either no available bandwidth or logical channel numbers available on one or more of the trunks for this path in the receive direction. trunkFailure- A trunk on the path has failed or has gone down due to a provisioning change of a critical attribute. trunkCardFailure- A trunk FP card has failed along the path. accessCardFailure- The FP on which the peer access service was running has failed. operatorForced- The path has terminated due to the operator locking a trunk along the path. lostLcnClash- The path has terminated because the PA's at both ends of an intermediate trunk have allocated the same LC to different calls. When this happens both calls must go down and then try to come up again a fraction of a second later (effectively ensuring that they will now be assigned different LC's). It is normal to get the odd clash especially when the PA's usedLC is approaching the PA's maxLC. networkCongestion - The path has failed due to control information being lost and not recoverable. trunkNotFound - Occurs on a manual path usually. Check for trunks not up or names provisioned incorrectly. farEndNotFound - The far end is not provisioned or is not up. Check remote Name. wrongModuleReached - This may occur on a manual path. Check provisioning for correct trunk and service names. For a normal path, the network Topology may be changing check remoteName. farEndBusy - The far end has been reached but it is busy. Check remoteName and remote end provisioning. callLoopedBack - This LCo is provisioned to call itself. Re- provision since this is invalid. unknownReason - The failure was not resolved. farEndNotReady - The remote end was reached but the connection was refused due to the remote end not being enabled. remoteNameMismatch - The remote end has alarmed and rejected this setup due to remoteName provisioning. serviceTypeMismatch - The remote Service Type does not match this service type. Check provisioning. reconnectFromFarEnd - The remote end re-established this connection. Check the remote end lastTearDownReason to determine the real reason. bumped - Another call bumped this path from a trunk to get bandwidth (or an LC) which it required to come up. This other path had a higher setupPriority than this path's holdingPriority hence it was allowed to steal the bandwidth (or LC) from this path. optimized - This call has been rerouted due to the optimization feature. The call is still active this just indicates why the path changed. trunkOrFarEndDidNotSupportMode - This call was unable to complete because a mode required by the service was not supported by one of the trunks the route went through or by the far end service it connected to. Currently the only mode that this applies to is the map/mux mode on TRUNK PA ATM component. Map mode was required by the application (CES/FrAtm etc.) but was not available on the TRUNK PA ATM component through which the call was routed or the far end CES/FrAtm component did not specify the same mode.
OBJECT-TYPE    
  INTEGER none(0), normalShutDown(1), insufficientTxLcOrBandwidth(2), insufficientRxLcOrBandwidth(3), trunkFailure(4), trunkCardFailure(5), operatorForced(6), lostLcnClash(7), networkCongestion(8), trunkNotFound(9), farEndNotFound(10), wrongModuleReached(11), farEndBusy(12), callLoopedBack(13), unknownReason(14), farEndNotReady(15), remoteNameMismatch(16), serviceTypeMismatch(17), reconnectFromFarEnd(18), bumped(19), accessCardFailure(20), optimized(21), overrideRemoteName(22), trunkOrFarEndDidNotSupportMode(23)  

mscVsrSvsLCoPathFailureAction 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.22
This attribute displays whether the application is set to tolerate momentary interruption of a path while a new path is selected. If disconnectConnection is displayed, the application is informed as soon as possible about a failure by disconnection. If the attribute displays reRoutePath, the path may attempt an immediate reroute, provided the failure is a recoverable failure. If rerouting fails the application is informed of the failure. With this option set to reRoutePath the LCo may wait up to 30 seconds before informing the service of complete disconnection in order to allow both ends to attempt to reconnect. Note that if PLC components are different at both ends only the calling end is allowed to reconnect. All pathTypes respect this attribute. Also on a manualPath with both ends provisioned with independent paths (at least with respect to the failure) this option will have the desired effect that the path is rerouted without complete disconnection at both ends
OBJECT-TYPE    
  INTEGER disconnectConnection(0), reRoutePath(1)  

mscVsrSvsLCoBumpPreference 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.23
This attribute specifies when bumping will occur during route selection process. Bumping may occur when necessary or always. It will be necessary for a connection to bump if there is not enough resources for the connection to be established and these resources are occupied by a connection whose setupPriority is lower (numerically higher) than the connection's setupPriority. A connection may also always bump in order to obtain the best route.
OBJECT-TYPE    
  INTEGER bumpWhenNecessary(0), bumpToObtainBestRoute(1)  

mscVsrSvsLCoOptimization 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.24
This attribute is used to specify whether this connection should attempt to optimize its path when requested by the routing PORS component. Every path is as optimal as it can be when it is established, but as network traffic patterns and configurations change this path may no longer be as optimal as it could be. The PORS connection manager on a module requests circuits to optimize at the optimization interval.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscVsrSvsLCoPathUpDateTime 1.3.6.1.4.1.562.36.2.1.117.2.3.10.1.25
This is the time stamp when the current path was established or reestablished.
OBJECT-TYPE    
  EnterpriseDateAndTime SIZE(0 | 19)  

mscVsrSvsLCoStatsTable 1.3.6.1.4.1.562.36.2.1.117.2.3.11
This group contains the operational statistics attributes for the path oriented LCo.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsLCoStatsEntry

mscVsrSvsLCoStatsEntry 1.3.6.1.4.1.562.36.2.1.117.2.3.11.1
An entry in the mscVsrSvsLCoStatsTable.
OBJECT-TYPE    
  MscVsrSvsLCoStatsEntry  

mscVsrSvsLCoPktsToNetwork 1.3.6.1.4.1.562.36.2.1.117.2.3.11.1.1
This attribute counts the number of packets transmitted to the network over this Logical Connection.
OBJECT-TYPE    
  PassportCounter64  

mscVsrSvsLCoBytesToNetwork 1.3.6.1.4.1.562.36.2.1.117.2.3.11.1.2
This attribute counts the number of bytes sent to the network over this Logical Connection.
OBJECT-TYPE    
  PassportCounter64  

mscVsrSvsLCoPktsFromNetwork 1.3.6.1.4.1.562.36.2.1.117.2.3.11.1.3
This attribute counts the number of packets received from the remote LCo via the network.
OBJECT-TYPE    
  PassportCounter64  

mscVsrSvsLCoBytesFromNetwork 1.3.6.1.4.1.562.36.2.1.117.2.3.11.1.4
This attribute counts the number of bytes received from the remote LCo via the network.
OBJECT-TYPE    
  PassportCounter64  

mscVsrSvsLCoPathTable 1.3.6.1.4.1.562.36.2.1.117.2.3.264
This attribute contains the trunk component names over which the path has been instantiated and the remote end point name terminating the path.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsLCoPathEntry

mscVsrSvsLCoPathEntry 1.3.6.1.4.1.562.36.2.1.117.2.3.264.1
An entry in the mscVsrSvsLCoPathTable.
OBJECT-TYPE    
  MscVsrSvsLCoPathEntry  

mscVsrSvsLCoPathValue 1.3.6.1.4.1.562.36.2.1.117.2.3.264.1.1
This variable represents both the value and the index for the mscVsrSvsLCoPathTable.
OBJECT-TYPE    
  AsciiString SIZE(0..40)  

mscVsrSvsDebug 1.3.6.1.4.1.562.36.2.1.117.2.4
OBJECT IDENTIFIER    

mscVsrSvsDebugRowStatusTable 1.3.6.1.4.1.562.36.2.1.117.2.4.1
This entry controls the addition and deletion of mscVsrSvsDebug components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsDebugRowStatusEntry

mscVsrSvsDebugRowStatusEntry 1.3.6.1.4.1.562.36.2.1.117.2.4.1.1
A single entry in the table represents a single mscVsrSvsDebug component.
OBJECT-TYPE    
  MscVsrSvsDebugRowStatusEntry  

mscVsrSvsDebugRowStatus 1.3.6.1.4.1.562.36.2.1.117.2.4.1.1.1
This variable is used as the basis for SNMP naming of mscVsrSvsDebug components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscVsrSvsDebugComponentName 1.3.6.1.4.1.562.36.2.1.117.2.4.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscVsrSvsDebugStorageType 1.3.6.1.4.1.562.36.2.1.117.2.4.1.1.4
This variable represents the storage type value for the mscVsrSvsDebug tables.
OBJECT-TYPE    
  StorageType  

mscVsrSvsDebugIndex 1.3.6.1.4.1.562.36.2.1.117.2.4.1.1.10
This variable represents the index for the mscVsrSvsDebug tables.
OBJECT-TYPE    
  NonReplicated  

mscVsrSvsIfEntryTable 1.3.6.1.4.1.562.36.2.1.117.2.11
This group contains the provisionable attributes for the ifEntry.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsIfEntryEntry

mscVsrSvsIfEntryEntry 1.3.6.1.4.1.562.36.2.1.117.2.11.1
An entry in the mscVsrSvsIfEntryTable.
OBJECT-TYPE    
  MscVsrSvsIfEntryEntry  

mscVsrSvsIfAdminStatus 1.3.6.1.4.1.562.36.2.1.117.2.11.1.1
The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mscVsrSvsIfIndex 1.3.6.1.4.1.562.36.2.1.117.2.11.1.2
This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
OBJECT-TYPE    
  InterfaceIndex 1..65535  

mscVsrSvsOperTable 1.3.6.1.4.1.562.36.2.1.117.2.12
This group provides the operational attributes for the SwitchedVoiceService component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsOperEntry

mscVsrSvsOperEntry 1.3.6.1.4.1.562.36.2.1.117.2.12.1
An entry in the mscVsrSvsOperTable.
OBJECT-TYPE    
  MscVsrSvsOperEntry  

mscVsrSvsStatus 1.3.6.1.4.1.562.36.2.1.117.2.12.1.1
This attribute indicates the current state of the channel. idle means that there is no call currently active on this channel. seized means that the channel is currently setting up a call, but a connect message has not been received. answered means that a connect message has been received. clearing means that the call is being taken down. lockout means that due to glare or channel rejection, the channel is available for ingress calls only. That is, either the PBX and the Passport tried to seize the channel for a call at the same time (glare), or the PBX rejected the Passport seizure. idleMaintenance means that due to explicit channel maintenance messages, the channel is not available for egress calls. This can only happen when the protocol control places the channel into a maintenance state, and only happens if the Passport receives a message causing the channel state change such as the SERVICE maintenance message.
OBJECT-TYPE    
  INTEGER idle(0), seized(1), answered(2), clearing(3), lockout(4), idleMaintenance(5)  

mscVsrSvsProfileNumber 1.3.6.1.4.1.562.36.2.1.117.2.12.1.2
This attribute indicates the VoiceProfile number that is being used for this call. If no call is active, then it displays the value of the last profile used.
OBJECT-TYPE    
  Counter32  

mscVsrSvsCallType 1.3.6.1.4.1.562.36.2.1.117.2.12.1.3
This attribute indicates the type of call that this channel is currently carrying. If no call is active, then it displays the value for the last call.
OBJECT-TYPE    
  INTEGER voice(0), data(1), modem(2)  

mscVsrSvsCalledNumber 1.3.6.1.4.1.562.36.2.1.117.2.12.1.4
This attribute indicates the dialled number that is active on this channel. If no call is active, then it displays the dialled number from the last call.
OBJECT-TYPE    
  DigitString SIZE(1..32)  

mscVsrSvsCallingNumber 1.3.6.1.4.1.562.36.2.1.117.2.12.1.5
This attribute indicates the originator's number for the currently active call. If no call is active, then it displays the originator's number from the last call.
OBJECT-TYPE    
  DigitString SIZE(1..16)  

mscVsrSvsClearCauseCode 1.3.6.1.4.1.562.36.2.1.117.2.12.1.6
This attribute indicates the clear cause code of the call. This code is always the Q.931 code, regardless of the access protocol.
OBJECT-TYPE    
  Hex 0..127  

mscVsrSvsStatsTable 1.3.6.1.4.1.562.36.2.1.117.2.13
This group provides the operational attributes for the SwitchedVoiceService component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsStatsEntry

mscVsrSvsStatsEntry 1.3.6.1.4.1.562.36.2.1.117.2.13.1
An entry in the mscVsrSvsStatsTable.
OBJECT-TYPE    
  MscVsrSvsStatsEntry  

mscVsrSvsTotalCalls 1.3.6.1.4.1.562.36.2.1.117.2.13.1.1
This attribute counts the call attempts processed on this channel (in both directions). This counter includes the number of unsuccessful as well as successful call attempts. The value wraps when it reaches its maximum.
OBJECT-TYPE    
  Counter32  

mscVsrSvsTotalCallSeconds 1.3.6.1.4.1.562.36.2.1.117.2.13.1.2
This attribute indicates the total number of seconds that this channel is handling a call. This is regardless of whether the call is successful or not. In other words, this is the amount of time that the channel is not in the idle state. The value wraps when it reaches its maximum.
OBJECT-TYPE    
  Counter32  

mscVsrSvsStateTable 1.3.6.1.4.1.562.36.2.1.117.2.14
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsStateEntry

mscVsrSvsStateEntry 1.3.6.1.4.1.562.36.2.1.117.2.14.1
An entry in the mscVsrSvsStateTable.
OBJECT-TYPE    
  MscVsrSvsStateEntry  

mscVsrSvsAdminState 1.3.6.1.4.1.562.36.2.1.117.2.14.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscVsrSvsOperationalState 1.3.6.1.4.1.562.36.2.1.117.2.14.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscVsrSvsUsageState 1.3.6.1.4.1.562.36.2.1.117.2.14.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscVsrSvsOperStatusTable 1.3.6.1.4.1.562.36.2.1.117.2.15
This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrSvsOperStatusEntry

mscVsrSvsOperStatusEntry 1.3.6.1.4.1.562.36.2.1.117.2.15.1
An entry in the mscVsrSvsOperStatusTable.
OBJECT-TYPE    
  MscVsrSvsOperStatusEntry  

mscVsrSvsSnmpOperStatus 1.3.6.1.4.1.562.36.2.1.117.2.15.1.1
The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mscVsrDebug 1.3.6.1.4.1.562.36.2.1.117.3
OBJECT IDENTIFIER    

mscVsrDebugRowStatusTable 1.3.6.1.4.1.562.36.2.1.117.3.1
This entry controls the addition and deletion of mscVsrDebug components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrDebugRowStatusEntry

mscVsrDebugRowStatusEntry 1.3.6.1.4.1.562.36.2.1.117.3.1.1
A single entry in the table represents a single mscVsrDebug component.
OBJECT-TYPE    
  MscVsrDebugRowStatusEntry  

mscVsrDebugRowStatus 1.3.6.1.4.1.562.36.2.1.117.3.1.1.1
This variable is used as the basis for SNMP naming of mscVsrDebug components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscVsrDebugComponentName 1.3.6.1.4.1.562.36.2.1.117.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscVsrDebugStorageType 1.3.6.1.4.1.562.36.2.1.117.3.1.1.4
This variable represents the storage type value for the mscVsrDebug tables.
OBJECT-TYPE    
  StorageType  

mscVsrDebugIndex 1.3.6.1.4.1.562.36.2.1.117.3.1.1.10
This variable represents the index for the mscVsrDebug tables.
OBJECT-TYPE    
  NonReplicated  

mscVsrCidDataTable 1.3.6.1.4.1.562.36.2.1.117.10
This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrCidDataEntry

mscVsrCidDataEntry 1.3.6.1.4.1.562.36.2.1.117.10.1
An entry in the mscVsrCidDataTable.
OBJECT-TYPE    
  MscVsrCidDataEntry  

mscVsrCustomerIdentifier 1.3.6.1.4.1.562.36.2.1.117.10.1.1
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
OBJECT-TYPE    
  Unsigned32 0 | 1..8191  

mscVsrIfEntryTable 1.3.6.1.4.1.562.36.2.1.117.11
This group contains the provisionable attributes for the ifEntry.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrIfEntryEntry

mscVsrIfEntryEntry 1.3.6.1.4.1.562.36.2.1.117.11.1
An entry in the mscVsrIfEntryTable.
OBJECT-TYPE    
  MscVsrIfEntryEntry  

mscVsrIfAdminStatus 1.3.6.1.4.1.562.36.2.1.117.11.1.1
The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mscVsrIfIndex 1.3.6.1.4.1.562.36.2.1.117.11.1.2
This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
OBJECT-TYPE    
  InterfaceIndex 1..65535  

mscVsrProvTable 1.3.6.1.4.1.562.36.2.1.117.12
This group represents the provisionable attributes of a VoiceSubroute.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrProvEntry

mscVsrProvEntry 1.3.6.1.4.1.562.36.2.1.117.12.1
An entry in the mscVsrProvTable.
OBJECT-TYPE    
  MscVsrProvEntry  

mscVsrCommentText 1.3.6.1.4.1.562.36.2.1.117.12.1.1
Use of this attribute is at the discretion of the system administrator. Typically, it specifies the name of the customer that is using this VoiceSubroute. Typical use of this attribute is to store customer name.
OBJECT-TYPE    
  AsciiString SIZE(0..40)  

mscVsrVoiceRoute 1.3.6.1.4.1.562.36.2.1.117.12.1.3
This attribute specifies the VoiceRoute component that this VoiceSubroute belongs to.
OBJECT-TYPE    
  Link  

mscVsrSignallingChannel 1.3.6.1.4.1.562.36.2.1.117.12.1.311
This attribute specifies the signalling channel to be used by the VoiceSubroute.
OBJECT-TYPE    
  Link  

mscVsrStateTable 1.3.6.1.4.1.562.36.2.1.117.13
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrStateEntry

mscVsrStateEntry 1.3.6.1.4.1.562.36.2.1.117.13.1
An entry in the mscVsrStateTable.
OBJECT-TYPE    
  MscVsrStateEntry  

mscVsrAdminState 1.3.6.1.4.1.562.36.2.1.117.13.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscVsrOperationalState 1.3.6.1.4.1.562.36.2.1.117.13.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscVsrUsageState 1.3.6.1.4.1.562.36.2.1.117.13.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscVsrOperStatusTable 1.3.6.1.4.1.562.36.2.1.117.14
This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrOperStatusEntry

mscVsrOperStatusEntry 1.3.6.1.4.1.562.36.2.1.117.14.1
An entry in the mscVsrOperStatusTable.
OBJECT-TYPE    
  MscVsrOperStatusEntry  

mscVsrSnmpOperStatus 1.3.6.1.4.1.562.36.2.1.117.14.1.1
The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

mscVsrStatsTable 1.3.6.1.4.1.562.36.2.1.117.15
This group provides the operational statistics for the VoiceSubroute component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrStatsEntry

mscVsrStatsEntry 1.3.6.1.4.1.562.36.2.1.117.15.1
An entry in the mscVsrStatsTable.
OBJECT-TYPE    
  MscVsrStatsEntry  

mscVsrTotalCallsFromIf 1.3.6.1.4.1.562.36.2.1.117.15.1.1
This attribute indicates the total number of calls that have been received by this VoiceSubroute from the PBX. The value wraps to zero when it reaches its maximum.
OBJECT-TYPE    
  Counter32  

mscVsrTotalFailedCallsFromIf 1.3.6.1.4.1.562.36.2.1.117.15.1.2
This attribute counts indicates the total number of calls that have been received by this VoiceSubroute from the PBX which failed to be successfully routed through the subnet for various reasons. The value wraps to zero when it reaches its maximum.
OBJECT-TYPE    
  Counter32  

mscVsrInvalidNumberingPlanCalls 1.3.6.1.4.1.562.36.2.1.117.15.1.3
This attribute counts the calls from the interface for which the type of number and the numbering plan identification was not associated to an access code. The numbering plan types noAccessCode, accessCode1 and accessCode2 are provisioned in the VoiceRoute. Refer to NTP-241-7001-xxx for more information. The value wraps to zero when it reaches its maximum.
OBJECT-TYPE    
  Counter32  

mscVsrAddressResolutionFailedCalls 1.3.6.1.4.1.562.36.2.1.117.15.1.4
This attribute counts the calls from the interface which had dialled numbers that had no entry in the VoiceNetworkingCallServer data base. The value wraps to zero when it reaches its maximum.
OBJECT-TYPE    
  Counter32  

mscVsrAddressIncompleteCalls 1.3.6.1.4.1.562.36.2.1.117.15.1.5
This attribute counts the calls from the interface which had dialled numbers with insufficient digits to resolve to a unique entry in the VoiceNetworkingCallServer data base. The value wraps to zero when it reaches its maximum.
OBJECT-TYPE    
  Counter32  

mscVsrPathAttributesNotMetCalls 1.3.6.1.4.1.562.36.2.1.117.15.1.6
This attribute counts the calls from the interface for which a path to the end point could not be established based on the attributes specified in the VoiceProfile. The value wraps to zero when it reaches its maximum.
OBJECT-TYPE    
  Counter32  

mscVsrPathSetupTimeOutCalls 1.3.6.1.4.1.562.36.2.1.117.15.1.7
This attribute counts the calls from the interface for which a path to the end point could not be established due to a subnet path setup time-out. The value wraps to zero when it reaches its maximum.
OBJECT-TYPE    
  Counter32  

mscVsrCallsRejectedLocally 1.3.6.1.4.1.562.36.2.1.117.15.1.8
This attribute counts the calls from the interface which were rejected by the originating end because it was: 1) a data call on a voice only VoiceRoute, or 2) a voice call on a data only VoiceRoute, or 3) a data call to an end-point whose VoiceProfile prevents data calls from being made. The value wraps to zero when it reaches its maximum.
OBJECT-TYPE    
  Counter32  

mscVsrCallsRejectedByFarEnd 1.3.6.1.4.1.562.36.2.1.117.15.1.9
This attribute counts the calls from the interface which were rejected by the far-end. This rejection could be due to: 1) no free channels at the end-point, or 2) a voice call going to a data only VoiceRoute, or 3) a data call going to a voice only VoiceRoute, or 4) a signalling protocol incompatibility between end-points. The value wraps to zero when it reaches its maximum.
OBJECT-TYPE    
  Counter32  

mscVsrOperTable 1.3.6.1.4.1.562.36.2.1.117.16
This group provides the operational attributes for the VoiceSubroute component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscVsrOperEntry

mscVsrOperEntry 1.3.6.1.4.1.562.36.2.1.117.16.1
An entry in the mscVsrOperTable.
OBJECT-TYPE    
  MscVsrOperEntry  

mscVsrActiveChannels 1.3.6.1.4.1.562.36.2.1.117.16.1.2
This attribute indicates the total number of B-channels that currently have active calls.
OBJECT-TYPE    
  Counter32  

mscVsrPeakActiveChannels 1.3.6.1.4.1.562.36.2.1.117.16.1.3
This attribute indicates the peak number of B-channels that were active during the previous polling period.
OBJECT-TYPE    
  Counter32  

mscVsrActiveVoiceChannels 1.3.6.1.4.1.562.36.2.1.117.16.1.4
This attribute indicates the number of B-channels that are currently carrying voice.
OBJECT-TYPE    
  Counter32  

mscVsrActiveModemChannels 1.3.6.1.4.1.562.36.2.1.117.16.1.5
This attribute indicates the number of B-channels that are currently active, where a 2100Hz tone was detected.
OBJECT-TYPE    
  Counter32  

mscVsrActiveDataChannels 1.3.6.1.4.1.562.36.2.1.117.16.1.6
This attribute indicates the number of B-channels that are currently active carrying data.
OBJECT-TYPE    
  Counter32  

mscVsrPeakActiveVoiceChannels 1.3.6.1.4.1.562.36.2.1.117.16.1.7
This attribute indicates the peak number of B-channels that were active carrying voice during the previous polling period.
OBJECT-TYPE    
  Counter32  

mscVsrPeakActiveModemChannels 1.3.6.1.4.1.562.36.2.1.117.16.1.8
This attribute indicates the peak number of active B-channels that a 2100Hz tone was detected during the previous polling period.
OBJECT-TYPE    
  Counter32  

mscVsrPeakActiveDataChannels 1.3.6.1.4.1.562.36.2.1.117.16.1.9
This attribute indicates the maximum number of B-channels that were active carrying data during the previous polling period.
OBJECT-TYPE    
  Counter32  

mscVsrActiveFaxRelayChannels 1.3.6.1.4.1.562.36.2.1.117.16.1.10
This attribute indicates the number of B-channels that are currently performing fax relay.
OBJECT-TYPE    
  Gauge32 0..30  

mscVsrActiveTptChannels 1.3.6.1.4.1.562.36.2.1.117.16.1.11
This attribute indicates the number of B-channels that are currently performing tandem pass through.
OBJECT-TYPE    
  Gauge32 0..32  

mscVsrPeakActiveFaxRelayChannels 1.3.6.1.4.1.562.36.2.1.117.16.1.12
This attribute indicates the peak number of B-channels that performed fax relay during the previous polling period.
OBJECT-TYPE    
  Gauge32 0..30  

mscVsrPeakActiveTptChannels 1.3.6.1.4.1.562.36.2.1.117.16.1.13
This attribute indicates the peak number of B-channels that performed tandem pass through during the previous polling period.
OBJECT-TYPE    
  Gauge32 0..30  

voiceNetworkingMIB 1.3.6.1.4.1.562.36.2.2.109
OBJECT IDENTIFIER    

voiceNetworkingGroup 1.3.6.1.4.1.562.36.2.2.109.1
OBJECT IDENTIFIER    

voiceNetworkingGroupCA 1.3.6.1.4.1.562.36.2.2.109.1.1
OBJECT IDENTIFIER    

voiceNetworkingGroupCA02 1.3.6.1.4.1.562.36.2.2.109.1.1.3
OBJECT IDENTIFIER    

voiceNetworkingGroupCA02A 1.3.6.1.4.1.562.36.2.2.109.1.1.3.2
OBJECT IDENTIFIER    

voiceNetworkingCapabilities 1.3.6.1.4.1.562.36.2.2.109.3
OBJECT IDENTIFIER    

voiceNetworkingCapabilitiesCA 1.3.6.1.4.1.562.36.2.2.109.3.1
OBJECT IDENTIFIER    

voiceNetworkingCapabilitiesCA02 1.3.6.1.4.1.562.36.2.2.109.3.1.3
OBJECT IDENTIFIER    

voiceNetworkingCapabilitiesCA02A 1.3.6.1.4.1.562.36.2.2.109.3.1.3.2
OBJECT IDENTIFIER    

Defined Objects

MscSigChanRowStatusEntry  
SEQUENCE    
  RowStatus as mscSigChanRowStatus  
  DisplayString as mscSigChanComponentName  
  StorageType as mscSigChanStorageType  
  Integer32 as mscSigChanIndex  

MscSigChanCidDataEntry  
SEQUENCE    
  Unsigned32 as mscSigChanCustomerIdentifier  

MscSigChanIfEntryEntry  
SEQUENCE    
  INTEGER as mscSigChanIfAdminStatus  
  InterfaceIndex as mscSigChanIfIndex  

MscSigChanOperStatusEntry  
SEQUENCE    
  INTEGER as mscSigChanSnmpOperStatus  

MscSigChanStateEntry  
SEQUENCE    
  INTEGER as mscSigChanAdminState  
  INTEGER as mscSigChanOperationalState  
  INTEGER as mscSigChanUsageState  

MscSigChanProvEntry  
SEQUENCE    
  AsciiString as mscSigChanCommentText  
  INTEGER as mscSigChanOctothorpeEod  
  INTEGER as mscSigChanForceNpiTon  
  INTEGER as mscSigChanDefaultNpiTon  

MscSigChanSubroutesEntry  
SEQUENCE    
  Link as mscSigChanSubroutesValue  
  RowStatus as mscSigChanSubroutesRowStatus  

MscSigChanDegradedSubroutesEntry  
SEQUENCE    
  RowPointer as mscSigChanDegradedSubroutesValue  

MscSigChanBchRowStatusEntry  
SEQUENCE    
  RowStatus as mscSigChanBchRowStatus  
  DisplayString as mscSigChanBchComponentName  
  StorageType as mscSigChanBchStorageType  
  Integer32 as mscSigChanBchIndex  

MscSigChanBchOperEntry  
SEQUENCE    
  INTEGER as mscSigChanBchStatus  
  Unsigned32 as mscSigChanBchTimeSlot  
  Unsigned32 as mscSigChanBchVsrInstance  
  DigitString as mscSigChanBchCalledDirectoryNumber  

MscSigChanGwRowStatusEntry  
SEQUENCE    
  RowStatus as mscSigChanGwRowStatus  
  DisplayString as mscSigChanGwComponentName  
  StorageType as mscSigChanGwStorageType  
  NonReplicated as mscSigChanGwIndex  

MscSigChanGwStatsEntry  
SEQUENCE    
  Counter32 as mscSigChanGwRequiredConversions  
  Counter32 as mscSigChanGwUnsupportedConversions  

MscSigChanGwGwcEntry  
SEQUENCE    
  INTEGER as mscSigChanGwGwcIndex  
  INTEGER as mscSigChanGwGwcValue  

MscSigChanGwGatewayCapEntry  
SEQUENCE    
  INTEGER as mscSigChanGwGatewayCapIndex  
  INTEGER as mscSigChanGwGatewayCapValue  

MscSigChanNcasRowStatusEntry  
SEQUENCE    
  RowStatus as mscSigChanNcasRowStatus  
  DisplayString as mscSigChanNcasComponentName  
  StorageType as mscSigChanNcasStorageType  
  Integer32 as mscSigChanNcasIndex  

MscSigChanNcasOperEntry  
SEQUENCE    
  INTEGER as mscSigChanNcasDirection  
  Hex as mscSigChanNcasCallReference  
  DigitString as mscSigChanNcasCalledDirectoryNumber  
  Unsigned32 as mscSigChanNcasDuration  

MscSigChanICmapRowStatusEntry  
SEQUENCE    
  RowStatus as mscSigChanICmapRowStatus  
  DisplayString as mscSigChanICmapComponentName  
  StorageType as mscSigChanICmapStorageType  
  NonReplicated as mscSigChanICmapIndex  

MscSigChanICmapIntCauseEntry  
SEQUENCE    
  Unsigned32 as mscSigChanICmapEgressLinkOutOfServCause  
  Unsigned32 as mscSigChanICmapChanOrCircNotAvailCause  
  Unsigned32 as mscSigChanICmapTempFailureCause  
  Unsigned32 as mscSigChanICmapSwitchCongestCause  
  Unsigned32 as mscSigChanICmapReqChanOrCircNotAvailCause  
  Unsigned32 as mscSigChanICmapResourceUnavailCause  
  Unsigned32 as mscSigChanICmapServNotAllowedCause  
  Unsigned32 as mscSigChanICmapNoSuchChannelCause  
  Unsigned32 as mscSigChanICmapIncompatDestCause  

MscVRouteRowStatusEntry  
SEQUENCE    
  RowStatus as mscVRouteRowStatus  
  DisplayString as mscVRouteComponentName  
  StorageType as mscVRouteStorageType  
  Integer32 as mscVRouteIndex  

MscVRouteProvEntry  
SEQUENCE    
  AsciiString as mscVRouteCommentText  
  INTEGER as mscVRouteTypeOfRoute  
  OCTET STRING as mscVRouteDiallingPlan0  
  OCTET STRING as mscVRouteDiallingPlan1  
  OCTET STRING as mscVRouteDiallingPlan2  
  INTEGER as mscVRouteHuntingAlgorithm  
  Unsigned32 as mscVRouteMinimumDigitsToRoute  
  Link as mscVRouteVoiceNetworkingCallServer  
  DigitString as mscVRouteOverrideDirectoryNumber  
  Unsigned32 as mscVRoutePrivateNetworkIdentifer  

MscVRouteCidDataEntry  
SEQUENCE    
  Unsigned32 as mscVRouteCustomerIdentifier  

MscVRouteIfEntryEntry  
SEQUENCE    
  INTEGER as mscVRouteIfAdminStatus  
  InterfaceIndex as mscVRouteIfIndex  

MscVRouteStateEntry  
SEQUENCE    
  INTEGER as mscVRouteAdminState  
  INTEGER as mscVRouteOperationalState  
  INTEGER as mscVRouteUsageState  

MscVRouteOperStatusEntry  
SEQUENCE    
  INTEGER as mscVRouteSnmpOperStatus  

MscVRouteStatsEntry  
SEQUENCE    
  Counter32 as mscVRouteTotalCallsFromSubnet  
  Counter32 as mscVRouteCallsClearedNoChannel  
  Counter32 as mscVRouteCallsClearedOutOfService  
  Counter32 as mscVRouteCallsRejected  

MscVRouteSubroutesEntry  
SEQUENCE    
  Link as mscVRouteSubroutesValue  
  RowStatus as mscVRouteSubroutesRowStatus  

MscVRouteDegradedSubroutesEntry  
SEQUENCE    
  RowPointer as mscVRouteDegradedSubroutesValue  

MscVRouteDebugRowStatusEntry  
SEQUENCE    
  RowStatus as mscVRouteDebugRowStatus  
  DisplayString as mscVRouteDebugComponentName  
  StorageType as mscVRouteDebugStorageType  
  NonReplicated as mscVRouteDebugIndex  

MscVRouteInterfaceRowStatusEntry  
SEQUENCE    
  RowStatus as mscVRouteInterfaceRowStatus  
  DisplayString as mscVRouteInterfaceComponentName  
  StorageType as mscVRouteInterfaceStorageType  
  NonReplicated as mscVRouteInterfaceIndex  

MscVRouteInterfaceProvEntry  
SEQUENCE    
  INTEGER as mscVRouteInterfaceIngressAudioGain  
  INTEGER as mscVRouteInterfaceEgressAudioGain  
  INTEGER as mscVRouteInterfaceTandemPassThrough  
  INTEGER as mscVRouteInterfaceEchoCancellation  
  INTEGER as mscVRouteInterfaceComfortNoiseCap  
  Unsigned32 as mscVRouteInterfaceSpeechHangoverTime  
  Unsigned32 as mscVRouteInterfaceFaxHangoverTimeG711G726  
  INTEGER as mscVRouteInterfaceModemFaxSpeechDiscrim  
  Unsigned32 as mscVRouteInterfaceEchoTailDelay  
  Unsigned32 as mscVRouteInterfaceEchoReturnLoss  
  INTEGER as mscVRouteInterfaceEcanBypassMode  

MscVRouteInterfaceStructuredEchoCancellationEntry  
SEQUENCE    
  INTEGER as mscVRouteInterfaceStructuredEchoCancellationIndex  
  INTEGER as mscVRouteInterfaceStructuredEchoCancellationValue  

MscVRouteDnaRowStatusEntry  
SEQUENCE    
  RowStatus as mscVRouteDnaRowStatus  
  DisplayString as mscVRouteDnaComponentName  
  StorageType as mscVRouteDnaStorageType  
  NonReplicated as mscVRouteDnaIndex  

MscVRouteDnaAddressEntry  
SEQUENCE    
  INTEGER as mscVRouteDnaNumberingPlanIndicator  
  DigitString as mscVRouteDnaDataNetworkAddress  

MscVRouteAcctRowStatusEntry  
SEQUENCE    
  RowStatus as mscVRouteAcctRowStatus  
  DisplayString as mscVRouteAcctComponentName  
  StorageType as mscVRouteAcctStorageType  
  NonReplicated as mscVRouteAcctIndex  

MscVRouteAcctProvEntry  
SEQUENCE    
  OCTET STRING as mscVRouteAcctAccountCollection  
  Unsigned32 as mscVRouteAcctAccountClass  
  Unsigned32 as mscVRouteAcctServiceExchange  
  Unsigned32 as mscVRouteAcctDigitsSuppressed  
  OCTET STRING as mscVRouteAcctAccountingOptions  

MscVsrRowStatusEntry  
SEQUENCE    
  RowStatus as mscVsrRowStatus  
  DisplayString as mscVsrComponentName  
  StorageType as mscVsrStorageType  
  Integer32 as mscVsrIndex  

MscVsrCidDataEntry  
SEQUENCE    
  Unsigned32 as mscVsrCustomerIdentifier  

MscVsrIfEntryEntry  
SEQUENCE    
  INTEGER as mscVsrIfAdminStatus  
  InterfaceIndex as mscVsrIfIndex  

MscVsrProvEntry  
SEQUENCE    
  AsciiString as mscVsrCommentText  
  Link as mscVsrVoiceRoute  
  Link as mscVsrSignallingChannel  

MscVsrStateEntry  
SEQUENCE    
  INTEGER as mscVsrAdminState  
  INTEGER as mscVsrOperationalState  
  INTEGER as mscVsrUsageState  

MscVsrOperStatusEntry  
SEQUENCE    
  INTEGER as mscVsrSnmpOperStatus  

MscVsrStatsEntry  
SEQUENCE    
  Counter32 as mscVsrTotalCallsFromIf  
  Counter32 as mscVsrTotalFailedCallsFromIf  
  Counter32 as mscVsrInvalidNumberingPlanCalls  
  Counter32 as mscVsrAddressResolutionFailedCalls  
  Counter32 as mscVsrAddressIncompleteCalls  
  Counter32 as mscVsrPathAttributesNotMetCalls  
  Counter32 as mscVsrPathSetupTimeOutCalls  
  Counter32 as mscVsrCallsRejectedLocally  
  Counter32 as mscVsrCallsRejectedByFarEnd  

MscVsrOperEntry  
SEQUENCE    
  Counter32 as mscVsrActiveChannels  
  Counter32 as mscVsrPeakActiveChannels  
  Counter32 as mscVsrActiveVoiceChannels  
  Counter32 as mscVsrActiveModemChannels  
  Counter32 as mscVsrActiveDataChannels  
  Counter32 as mscVsrPeakActiveVoiceChannels  
  Counter32 as mscVsrPeakActiveModemChannels  
  Counter32 as mscVsrPeakActiveDataChannels  
  Gauge32 as mscVsrActiveFaxRelayChannels  
  Gauge32 as mscVsrActiveTptChannels  
  Gauge32 as mscVsrPeakActiveFaxRelayChannels  
  Gauge32 as mscVsrPeakActiveTptChannels  

MscVsrSvsRowStatusEntry  
SEQUENCE    
  RowStatus as mscVsrSvsRowStatus  
  DisplayString as mscVsrSvsComponentName  
  StorageType as mscVsrSvsStorageType  
  Integer32 as mscVsrSvsIndex  

MscVsrSvsIfEntryEntry  
SEQUENCE    
  INTEGER as mscVsrSvsIfAdminStatus  
  InterfaceIndex as mscVsrSvsIfIndex  

MscVsrSvsOperEntry  
SEQUENCE    
  INTEGER as mscVsrSvsStatus  
  Counter32 as mscVsrSvsProfileNumber  
  INTEGER as mscVsrSvsCallType  
  DigitString as mscVsrSvsCalledNumber  
  DigitString as mscVsrSvsCallingNumber  
  Hex as mscVsrSvsClearCauseCode  

MscVsrSvsStatsEntry  
SEQUENCE    
  Counter32 as mscVsrSvsTotalCalls  
  Counter32 as mscVsrSvsTotalCallSeconds  

MscVsrSvsStateEntry  
SEQUENCE    
  INTEGER as mscVsrSvsAdminState  
  INTEGER as mscVsrSvsOperationalState  
  INTEGER as mscVsrSvsUsageState  

MscVsrSvsOperStatusEntry  
SEQUENCE    
  INTEGER as mscVsrSvsSnmpOperStatus  

MscVsrSvsFramerRowStatusEntry  
SEQUENCE    
  RowStatus as mscVsrSvsFramerRowStatus  
  DisplayString as mscVsrSvsFramerComponentName  
  StorageType as mscVsrSvsFramerStorageType  
  NonReplicated as mscVsrSvsFramerIndex  

MscVsrSvsFramerProvEntry  
SEQUENCE    
  Link as mscVsrSvsFramerInterfaceName  

MscVsrSvsFramerStateEntry  
SEQUENCE    
  INTEGER as mscVsrSvsFramerAdminState  
  INTEGER as mscVsrSvsFramerOperationalState  
  INTEGER as mscVsrSvsFramerUsageState  

MscVsrSvsFramerStatsEntry  
SEQUENCE    
  Unsigned32 as mscVsrSvsFramerTotalCells  
  Unsigned32 as mscVsrSvsFramerAudioCells  
  Unsigned32 as mscVsrSvsFramerSilenceCells  
  Unsigned32 as mscVsrSvsFramerModemCells  
  INTEGER as mscVsrSvsFramerCurrentEncodingRate  
  Unsigned32 as mscVsrSvsFramerLrcErrors  
  Unsigned32 as mscVsrSvsFramerFrmLostInNetwork  
  Unsigned32 as mscVsrSvsFramerFrmUnderRuns  
  Unsigned32 as mscVsrSvsFramerFrmDumped  
  Counter32 as mscVsrSvsFramerModemSilenceCells  
  INTEGER as mscVsrSvsFramerCurrentEncoding  
  INTEGER as mscVsrSvsFramerTptStatus  
  Counter32 as mscVsrSvsFramerFaxRelayCells  
  Unsigned32 as mscVsrSvsFramerModemFaxCells  
  Counter32 as mscVsrSvsFramerFaxIdleCells  

MscVsrSvsFramerOperEntry  
SEQUENCE    
  INTEGER as mscVsrSvsFramerOpCurrentEncoding  
  INTEGER as mscVsrSvsFramerCurrentRate  
  INTEGER as mscVsrSvsFramerOpTptStatus  

MscVsrSvsFramerNegEntry  
SEQUENCE    
  INTEGER as mscVsrSvsFramerNegotiatedSilenceSuppression  
  INTEGER as mscVsrSvsFramerNegotiatedFisG711G726  
  INTEGER as mscVsrSvsFramerNegotiatedDtmfRegeneration  
  INTEGER as mscVsrSvsFramerNegotiatedV17AsG711G726  
  INTEGER as mscVsrSvsFramerNegotiatedTandemPassThrough  

MscVsrSvsFramerFrmToNetworkEntry  
SEQUENCE    
  INTEGER as mscVsrSvsFramerFrmToNetworkIndex  
  Unsigned32 as mscVsrSvsFramerFrmToNetworkValue  

MscVsrSvsFramerFrmFromNetworkEntry  
SEQUENCE    
  INTEGER as mscVsrSvsFramerFrmFromNetworkIndex  
  Unsigned32 as mscVsrSvsFramerFrmFromNetworkValue  

MscVsrSvsFramerNEncodingEntry  
SEQUENCE    
  INTEGER as mscVsrSvsFramerNEncodingIndex  
  INTEGER as mscVsrSvsFramerNEncodingValue  

MscVsrSvsFramerNRatesEntry  
SEQUENCE    
  INTEGER as mscVsrSvsFramerNRatesTrafficIndex  
  INTEGER as mscVsrSvsFramerNRatesRateIndex  
  INTEGER as mscVsrSvsFramerNRatesValue  

MscVsrSvsFramerVfpDebugRowStatusEntry  
SEQUENCE    
  RowStatus as mscVsrSvsFramerVfpDebugRowStatus  
  DisplayString as mscVsrSvsFramerVfpDebugComponentName  
  StorageType as mscVsrSvsFramerVfpDebugStorageType  
  NonReplicated as mscVsrSvsFramerVfpDebugIndex  

MscVsrSvsFramerMvpDebugRowStatusEntry  
SEQUENCE    
  RowStatus as mscVsrSvsFramerMvpDebugRowStatus  
  DisplayString as mscVsrSvsFramerMvpDebugComponentName  
  StorageType as mscVsrSvsFramerMvpDebugStorageType  
  NonReplicated as mscVsrSvsFramerMvpDebugIndex  

MscVsrSvsFramerPcmCaptureRowStatusEntry  
SEQUENCE    
  RowStatus as mscVsrSvsFramerPcmCaptureRowStatus  
  DisplayString as mscVsrSvsFramerPcmCaptureComponentName  
  StorageType as mscVsrSvsFramerPcmCaptureStorageType  
  NonReplicated as mscVsrSvsFramerPcmCaptureIndex  

MscVsrSvsLCoRowStatusEntry  
SEQUENCE    
  RowStatus as mscVsrSvsLCoRowStatus  
  DisplayString as mscVsrSvsLCoComponentName  
  StorageType as mscVsrSvsLCoStorageType  
  NonReplicated as mscVsrSvsLCoIndex  

MscVsrSvsLCoPathDataEntry  
SEQUENCE    
  INTEGER as mscVsrSvsLCoState  
  AsciiString as mscVsrSvsLCoOverrideRemoteName  
  INTEGER as mscVsrSvsLCoEnd  
  Unsigned32 as mscVsrSvsLCoCostMetric  
  Unsigned32 as mscVsrSvsLCoDelayMetric  
  Unsigned32 as mscVsrSvsLCoRoundTripDelay  
  Unsigned32 as mscVsrSvsLCoSetupPriority  
  Unsigned32 as mscVsrSvsLCoHoldingPriority  
  Gauge32 as mscVsrSvsLCoRequiredTxBandwidth  
  Gauge32 as mscVsrSvsLCoRequiredRxBandwidth  
  INTEGER as mscVsrSvsLCoRequiredTrafficType  
  OCTET STRING as mscVsrSvsLCoPermittedTrunkTypes  
  Unsigned32 as mscVsrSvsLCoRequiredSecurity  
  Unsigned32 as mscVsrSvsLCoRequiredCustomerParameter  
  Unsigned32 as mscVsrSvsLCoEmissionPriority  
  Unsigned32 as mscVsrSvsLCoDiscardPriority  
  INTEGER as mscVsrSvsLCoPathType  
  Unsigned32 as mscVsrSvsLCoRetryCount  
  Unsigned32 as mscVsrSvsLCoPathFailureCount  
  INTEGER as mscVsrSvsLCoReasonForNoRoute  
  INTEGER as mscVsrSvsLCoLastTearDownReason  
  INTEGER as mscVsrSvsLCoPathFailureAction  
  INTEGER as mscVsrSvsLCoBumpPreference  
  INTEGER as mscVsrSvsLCoOptimization  
  EnterpriseDateAndTime as mscVsrSvsLCoPathUpDateTime  

MscVsrSvsLCoStatsEntry  
SEQUENCE    
  PassportCounter64 as mscVsrSvsLCoPktsToNetwork  
  PassportCounter64 as mscVsrSvsLCoBytesToNetwork  
  PassportCounter64 as mscVsrSvsLCoPktsFromNetwork  
  PassportCounter64 as mscVsrSvsLCoBytesFromNetwork  

MscVsrSvsLCoPathEntry  
SEQUENCE    
  AsciiString as mscVsrSvsLCoPathValue  

MscVsrSvsDebugRowStatusEntry  
SEQUENCE    
  RowStatus as mscVsrSvsDebugRowStatus  
  DisplayString as mscVsrSvsDebugComponentName  
  StorageType as mscVsrSvsDebugStorageType  
  NonReplicated as mscVsrSvsDebugIndex  

MscVsrDebugRowStatusEntry  
SEQUENCE    
  RowStatus as mscVsrDebugRowStatus  
  DisplayString as mscVsrDebugComponentName  
  StorageType as mscVsrDebugStorageType  
  NonReplicated as mscVsrDebugIndex