
| SNMPv2-SMI | SNMPv2-TC | RFC1213-MIB |
| lucent | 1.3.6.1.4.1.1751 | ||
| OBJECT IDENTIFIER | |||
| products | 1.3.6.1.4.1.1751.1 | ||
| OBJECT IDENTIFIER | |||
| orinocoproducts | 1.3.6.1.4.1.1751.1.4 | ||
| OBJECT IDENTIFIER | |||
| ap1000 | 1.3.6.1.4.1.1751.1.4.1 | ||
| OBJECT IDENTIFIER | |||
| rg1000 | 1.3.6.1.4.1.1751.1.4.2 | ||
| OBJECT IDENTIFIER | |||
| as1000 | 1.3.6.1.4.1.1751.1.4.3 | ||
| OBJECT IDENTIFIER | |||
| as2000 | 1.3.6.1.4.1.1751.1.4.4 | ||
| OBJECT IDENTIFIER | |||
| ap500 | 1.3.6.1.4.1.1751.1.4.5 | ||
| OBJECT IDENTIFIER | |||
| ap2000 | 1.3.6.1.4.1.1751.1.4.6 | ||
| OBJECT IDENTIFIER | |||
| rg2000 | 1.3.6.1.4.1.1751.1.4.7 | ||
| OBJECT IDENTIFIER | |||
| rg1100 | 1.3.6.1.4.1.1751.1.4.8 | ||
| OBJECT IDENTIFIER | |||
| mibs | 1.3.6.1.4.1.1751.2 | ||
| OBJECT IDENTIFIER | |||
| orinocomibs | 1.3.6.1.4.1.1751.2.4 | ||
| OBJECT IDENTIFIER | |||
| oRiNOCO-MIB | 1.3.6.1.4.1.1751.2.4 | ||
| MIB Definition used in the ORiNOCO Wireless Product Line: iso(1).org(3).dod(6).internet(1).private(4).enterprise(1). lucent(1751).mibs(2).orinocomibs(4) | |||
| MODULE-IDENTITY | |||
| orinocoSys | 1.3.6.1.4.1.1751.2.4.1 | ||
| OBJECT IDENTIFIER | |||
| orinocoSysInvMgmt | 1.3.6.1.4.1.1751.2.4.1.1 | ||
| OBJECT IDENTIFIER | |||
| oriSystemInvMgmtComponentTable | 1.3.6.1.4.1.1751.2.4.1.1.1 | ||
| This table contains the inventory management parameters for the various system components. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriSystemInvMgmtComponentTableEntry | |||
| oriSystemInvMgmtComponentTableEntry | 1.3.6.1.4.1.1751.2.4.1.1.1.1 | ||
| This object represents an entry within the system component table. | |||
| OBJECT-TYPE | |||
| OriSystemInvMgmtComponentTableEntry | |||
| oriSystemInvMgmtTableComponentIndex | 1.3.6.1.4.1.1751.2.4.1.1.1.1.1 | ||
| This parameter identifies the table index. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriSystemInvMgmtTableComponentSerialNumber | 1.3.6.1.4.1.1751.2.4.1.1.1.1.2 | ||
| This parameter identifies the system component serial number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriSystemInvMgmtTableComponentName | 1.3.6.1.4.1.1751.2.4.1.1.1.1.3 | ||
| This parameter identifies the system component name. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriSystemInvMgmtTableComponentId | 1.3.6.1.4.1.1751.2.4.1.1.1.1.4 | ||
| This parameter identifies the system component identification. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriSystemInvMgmtTableComponentVariant | 1.3.6.1.4.1.1751.2.4.1.1.1.1.5 | ||
| This parameter identifies the system component variant number. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriSystemInvMgmtTableComponentMajorVersion | 1.3.6.1.4.1.1751.2.4.1.1.1.1.6 | ||
| This parameter identifies the system component major version number. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriSystemInvMgmtTableComponentMinorVersion | 1.3.6.1.4.1.1751.2.4.1.1.1.1.7 | ||
| This parameter identifies the system component minor version number. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriSystemInvMgmtTableComponentIfTable | 1.3.6.1.4.1.1751.2.4.1.1.2 | ||
| This table contains the inventory management parameters for the various system components. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriSystemInvMgmtTableComponentIfTableEntry | |||
| oriSystemInvMgmtTableComponentIfTableEntry | 1.3.6.1.4.1.1751.2.4.1.1.2.1 | ||
| This object represents an entry in the component interface table. | |||
| OBJECT-TYPE | |||
| OriSystemInvMgmtTableComponentIfTableEntry | |||
| oriSystemInvMgmtInterfaceTableIndex | 1.3.6.1.4.1.1751.2.4.1.1.2.1.1 | ||
| This parameter identifies the interface table index. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriSystemInvMgmtInterfaceId | 1.3.6.1.4.1.1751.2.4.1.1.2.1.2 | ||
| This parameter identifies the system component interface identification. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriSystemInvMgmtInterfaceRole | 1.3.6.1.4.1.1751.2.4.1.1.2.1.3 | ||
| This parameter identifies the system component interface role. | |||
| OBJECT-TYPE | |||
| INTEGER | actor(1), supplier(2) | ||
| oriSystemInvMgmtInterfaceVariant | 1.3.6.1.4.1.1751.2.4.1.1.2.1.4 | ||
| This parameter identifies the system component's interface variant number. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriSystemInvMgmtInterfaceBottomNumber | 1.3.6.1.4.1.1751.2.4.1.1.2.1.5 | ||
| This parameter identifies the system component's interface bottom number. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriSystemInvMgmtInterfaceTopNumber | 1.3.6.1.4.1.1751.2.4.1.1.2.1.6 | ||
| This parameter identifies the system component's interface top number. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriSystemAdminState | 1.3.6.1.4.1.1751.2.4.1.2 | ||
| This parameter identifies the device's state. When the device is in normal mode it will accept new connections and pass traffic through normally. When the device is in maintenance mode, it will not pass traffic and will not accept new connections - it can only be managed or monitored by an SNMP based manager. The default value for this object should be normal. This object is supported by the following ORiNOCO Devices: - Access Server 2000 | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), maintenance(2) | ||
| oriSystemAdminStateTimer | 1.3.6.1.4.1.1751.2.4.1.3 | ||
| This parameter is a timer used when changing the device's state from Normal to Maintenance mode. When the device's state is changed from Normal to Maintenance mode or vice-versa this timer shall count down for the state to be changed. This timer is in seconds and can be set from 0 - 3600 seconds (0 - 60 minutes). The default value for this timer should be 15 minutes. This object is supported by the following ORiNOCO Devices: - Access Server 2000 | |||
| OBJECT-TYPE | |||
| Integer32 | 0..3600 | ||
| oriSystemReboot | 1.3.6.1.4.1.1751.2.4.1.4 | ||
| This variable must be set to reboot the ORiNOCO device. The value is the number of seconds to wait to do a reboot. This object is supported by the following ORiNOCO Devices: - Access Server 2000 - Access Point 2000 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriSystemContactEmail | 1.3.6.1.4.1.1751.2.4.1.5 | ||
| The textual identification of the contact person for this managed node, together with information on how to contact this person. This object is supported by the following ORiNOCO Devices: - Access Server 2000 - Access Point 2000 | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriSystemContactPhoneNumber | 1.3.6.1.4.1.1751.2.4.1.6 | ||
| The phone number for the contact person. This object is supported by the following ORiNOCO Devices: - Access Server 2000 - Access Point 2000 | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriSystemFlashUpdate | 1.3.6.1.4.1.1751.2.4.1.7 | ||
| When this variable is set, all the parameters that are to be comitted to flash will be written to flash. This will be done immediately after the value is set irrespective of the value that is set. This object is supported by the following ORiNOCO Devices: - Access Point 2000 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriSystemFlashBackupInterval | 1.3.6.1.4.1.1751.2.4.1.8 | ||
| The backup time interval for flash memory to be udpated. This object is supported by the following ORiNOCO Devices: - Access Point 2000 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriSystemEmergencyResetToDefault | 1.3.6.1.4.1.1751.2.4.1.9 | ||
| When this variable is set to 1, all the parameters shall be set to default values. This object is supported by the following ORiNOCO Devices: - Access Point 2000 | |||
| OBJECT-TYPE | |||
| Integer32 | 0..1 | ||
| orinocoIf | 1.3.6.1.4.1.1751.2.4.2 | ||
| OBJECT IDENTIFIER | |||
| orinocoWirelessIf | 1.3.6.1.4.1.1751.2.4.2.1 | ||
| OBJECT IDENTIFIER | |||
| oriWirelessIfPropertiesTable | 1.3.6.1.4.1.1751.2.4.2.1.1 | ||
| This table contains the information for the wireless LAN interfaces present in ORiNOCO devices. This table contains the radio properties and capabilities of the ORiNOCO Wireless Interface. This table is supported by the following ORiNOCO Devices: - Access Server 2000 - Access Point 2000 | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriWirelessIfPropertiesEntry | |||
| oriWirelessIfPropertiesEntry | 1.3.6.1.4.1.1751.2.4.2.1.1.1 | ||
| This parameter represents the entry in the interface table. This is described below. | |||
| OBJECT-TYPE | |||
| OriWirelessIfPropertiesEntry | |||
| oriWirelessIfPropertiesIndex | 1.3.6.1.4.1.1751.2.4.2.1.1.1.1 | ||
| This parameter represents a unique value for each interface. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriWirelessIfNetworkName | 1.3.6.1.4.1.1751.2.4.2.1.1.1.2 | ||
| This parameter represents the network name SSID) for this wireless interface. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriWirelessIfMediumReservation | 1.3.6.1.4.1.1751.2.4.2.1.1.1.3 | ||
| This parameter identifies the medium reservation value. The range for this parameter is 0 - 2347. The medium reservation specifies the number of octects in a frame above which a RTS/CTS handshake is performed. The default value is 2347, which disables RTS/CTS mode. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2347 | ||
| oriWirelessIfInterferenceRobustness | 1.3.6.1.4.1.1751.2.4.2.1.1.1.4 | ||
| This parameter enables or disables the interference robustness feature. The default value for this parameter is disable. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriWirelessIfDTIMPeriod | 1.3.6.1.4.1.1751.2.4.2.1.1.1.5 | ||
| This parameter represents the delivery traffic indication map period. This is the interval between the transmission of multicast frames on the wireless inteface. It is expressed in the Beacon messages. The recommended default value for this parameter is 1. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..65535 | ||
| oriWirelessIfChannel | 1.3.6.1.4.1.1751.2.4.2.1.1.1.6 | ||
| This parameter represents the radio frequency channel for this wireless interface. The default value for this parameter is 3. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..14 | ||
| oriWirelessIfDistancebetweenAPs | 1.3.6.1.4.1.1751.2.4.2.1.1.1.7 | ||
| This parameter identifies the distance between access points. The default value for this parameter should be large. | |||
| OBJECT-TYPE | |||
| INTEGER | large(1), medium(2), small(3) | ||
| oriWirelessIfMulticastRate | 1.3.6.1.4.1.1751.2.4.2.1.1.1.8 | ||
| This parameter identifies multicast rate of the wireless card. This is dependent on the distance between APs. This parameter is directly correlated with the multicast rate. When this parameter is set to small, the multicast rates can be 11 Mbit/s, 5.5 Mbit/s, 2 Mbit/s, and 1 Mbit/s. When this parameter is set to medium, the allowed rates are 5.5 Mbit/s, 2 Mbit/s, 1 Mbit/s. When this parameter is set to large, then the multicast rates can be set to 2 Mbits/s or 1 Mbits/s. The default value for this parameter should be two Mbits/sec. | |||
| OBJECT-TYPE | |||
| INTEGER | oneMegabitPerSecond(1), twoMegabitsPerSecond(2), fivedotfiveMegabitsPerSecond(3), elevenMegabitsPerSecond(4) | ||
| oriWirelessIfClosedSystem | 1.3.6.1.4.1.1751.2.4.2.1.1.1.9 | ||
| This parameter is used as a flag which identifies whether the device will accept association requests to this interface, for client stations configured with a network name of 'ANY'. When this parameter is disabled, it will accept association requests from client stations with a network name of 'ANY'. If this parameter is set to enable then the interface will only accept association requests that match the interface's network name. The default value for this parameter is disable. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriWirelessIfAllowedSupportedDataRates | 1.3.6.1.4.1.1751.2.4.2.1.1.1.10 | ||
| This parameter reflects the transmit rates supported by the physical interface or radio card. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| oriWirelessIfRegulatoryDomainList | 1.3.6.1.4.1.1751.2.4.2.1.1.1.11 | ||
| This parameter specifies to which regulatory domain the interface belongs to. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| oriWirelessIfAllowedChannels | 1.3.6.1.4.1.1751.2.4.2.1.1.1.12 | ||
| This parameter reflects the radio frequency channels that the interface supports. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| oriWirelessIfMACAddress | 1.3.6.1.4.1.1751.2.4.2.1.1.1.13 | ||
| The MAC address of the ORiNOCO PC card inserted in the ORiNOCO device. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| oriWirelessIfLoadBalancing | 1.3.6.1.4.1.1751.2.4.2.1.1.1.14 | ||
| This object is used to configure the load balancing feature in the ORiNOCO device. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriWirelessIfMediumDensityDistribution | 1.3.6.1.4.1.1751.2.4.2.1.1.1.15 | ||
| This object is used to configure the medium density distribution feature in the ORiNOCO device. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriWirelessIfSecurityTable | 1.3.6.1.4.1.1751.2.4.2.1.2 | ||
| This table contains the information for the wireless LAN interfaces present in ORiNOCO devices. This table contains the radio properties and capabilities of the ORiNOCO Wireless Interface. This table is supported by the following ORiNOCO Devices: - Access Point 2000 | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriWirelessIfSecurityEntry | |||
| oriWirelessIfSecurityEntry | 1.3.6.1.4.1.1751.2.4.2.1.2.1 | ||
| This parameter represents the entry in the interface table. This is described below. | |||
| OBJECT-TYPE | |||
| OriWirelessIfSecurityEntry | |||
| oriWirelessIfSecurityIndex | 1.3.6.1.4.1.1751.2.4.2.1.2.1.1 | ||
| This parameter represents a unique value for each interface. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriWirelessIfEncryptionOptions | 1.3.6.1.4.1.1751.2.4.2.1.2.1.2 | ||
| This parameter reflects the physical interface's capabilities, such as WEP support. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), wep(2), rcFour128(3) | ||
| oriWirelessIfEncryptionStatus | 1.3.6.1.4.1.1751.2.4.2.1.2.1.3 | ||
| This parameter indicates if WEP encryption is on or off for this interface. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriWirelessIfEncryptionKey1 | 1.3.6.1.4.1.1751.2.4.2.1.2.1.4 | ||
| This parameter represents Encryption Key 1. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriWirelessIfEncryptionKey2 | 1.3.6.1.4.1.1751.2.4.2.1.2.1.5 | ||
| This parameter represents Encryption Key 2. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriWirelessIfEncryptionKey3 | 1.3.6.1.4.1.1751.2.4.2.1.2.1.6 | ||
| This parameter represents Encryption Key 3. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriWirelessIfEncryptionKey4 | 1.3.6.1.4.1.1751.2.4.2.1.2.1.7 | ||
| This parameter represents Encryption Key 4. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriWirelessIfEncryptionTxKey | 1.3.6.1.4.1.1751.2.4.2.1.2.1.8 | ||
| This parameter indicates which Encryption key (0, 1, 2, or 3) will be used to encrypt the data sent over the air. The default value for this parameter should be key 1. | |||
| OBJECT-TYPE | |||
| INTEGER | key1(1), key2(2), key3(3), key4(4) | ||
| oriWirelessIfDenyNonEncryptedData | 1.3.6.1.4.1.1751.2.4.2.1.2.1.9 | ||
| This parameter indicates if this interface will accept or deny non-encrypted data. The default value for this parameters is disabled. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriWirelessIfProfileCode | 1.3.6.1.4.1.1751.2.4.2.1.2.1.10 | ||
| The varible comprises of a vendor indication (Lucent or an OEM customer) and a capability indication (eg. bronze or gold). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| orinocoEthernetIf | 1.3.6.1.4.1.1751.2.4.2.2 | ||
| OBJECT IDENTIFIER | |||
| oriEthernetIfSettings | 1.3.6.1.4.1.1751.2.4.2.2.1 | ||
| This variable is used to configure the Ethernet settings for ORiNOCO devices. Some ORiNOCO devices shall provide all the options listed above while others will not - this depends on the Ethernet interface of the device. | |||
| OBJECT-TYPE | |||
| INTEGER | tenMegabitPerSecHalfDuplex(1), tenMegabitPerSecFullDuplex(2), tenMegabitPerSecAutoDuplex(3), onehundredMegabitPerSecHalfDuplex(4), onehundredMegabitPerSecFullDuplex(5), autoSpeedHalfDuplex(6), autoSpeedAutoDuplex(7) | ||
| orinocoNet | 1.3.6.1.4.1.1751.2.4.3 | ||
| OBJECT IDENTIFIER | |||
| orinocoNetIP | 1.3.6.1.4.1.1751.2.4.3.1 | ||
| OBJECT IDENTIFIER | |||
| oriNetworkIPAddress | 1.3.6.1.4.1.1751.2.4.3.1.1 | ||
| This parameter represents the IP Address of the device. The default IP address that the device is configured is 10.0.0.1. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriNetworkIPSubnetMask | 1.3.6.1.4.1.1751.2.4.3.1.2 | ||
| This parameter represents the subnet mask of the device. The default value for this parameter should be 255.0.0.0. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriNetworkIPDefaultRouterIPAddress | 1.3.6.1.4.1.1751.2.4.3.1.3 | ||
| This parameter represents the IP address of the gateway or router on the network. The default IP address is 10.0.0.1 | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriNetworkIPDefaultTTL | 1.3.6.1.4.1.1751.2.4.3.1.4 | ||
| The default value inserted into the Time-To-Live (TTL) field of the IP header of datagrams originated at this entity, whenever a TTL value is not supplied by the transport layer protocol. The default value for this parameter should be 64. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriNetworkIPAddressType | 1.3.6.1.4.1.1751.2.4.3.1.5 | ||
| This parameter identifies if the device is configured to be assigned a static or dynamic IP address. | |||
| OBJECT-TYPE | |||
| INTEGER | static(1), dynamic(2) | ||
| orinocoNetIPX | 1.3.6.1.4.1.1751.2.4.3.2 | ||
| OBJECT IDENTIFIER | |||
| oriNetworkIPXProtocolSupport | 1.3.6.1.4.1.1751.2.4.3.2.1 | ||
| This variable represents what protocol will be active or supported by the device. For the AS-2000 device, it can be on IP mode, IPX mode, or both IP and IPX mode. The default value for this object should be IP. | |||
| OBJECT-TYPE | |||
| INTEGER | ip(1), ipx(2), both(3) | ||
| oriNetworkIPXDefaultRouterNodeNumber | 1.3.6.1.4.1.1751.2.4.3.2.2 | ||
| If the source IPX network number is not equal to the destination IPX Network number in the packet from wireless side to the wired side, then replace the destination Ethernet MAC address with the value of this object (Default IPX router node number). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriNetworkIPXEthernetEncapsulationFormat | 1.3.6.1.4.1.1751.2.4.3.2.3 | ||
| This object represents the encapsulation type to be used for the IPX packets sent on the wired side. | |||
| OBJECT-TYPE | |||
| INTEGER | ethII802dot3encapsulation(1), eth802dot3withSNAPHdr(2), eth802dot3withoutSNAPHdr(3) | ||
| oriNetworkIPXWiredtoWirelessBridgedPacketCount | 1.3.6.1.4.1.1751.2.4.3.2.4 | ||
| This object represents the number of packets bridged from the wired to wireless side. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriNetworkIPXWirelesstoWiredBridgedPacketCount | 1.3.6.1.4.1.1751.2.4.3.2.5 | ||
| This object represents the number of packets bridged from the wireless to wired side. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriNetworkIPXClientTable | 1.3.6.1.4.1.1751.2.4.3.2.6 | ||
| The (conceptual) table listing the AS Clients (IPX) connected to the Access Server 2000 device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriNetworkIPXClientEntry | |||
| oriNetworkIPXClientEntry | 1.3.6.1.4.1.1751.2.4.3.2.6.1 | ||
| An entry (conceptual row) representing a ASClient (IPX) connnected to the Access Server 2000 device. | |||
| OBJECT-TYPE | |||
| OriNetworkIPXClientEntry | |||
| oriNetworkIPXPPPSessionId | 1.3.6.1.4.1.1751.2.4.3.2.6.1.1 | ||
| The PPP Session ID assigned by the Access Server 2000 to this AS Client. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriNetworkIPXClientNetworkNumber | 1.3.6.1.4.1.1751.2.4.3.2.6.1.2 | ||
| The IPX Node Number assigned by the Novell Server to this IPX client. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| oriNetworkIPXClientMAC | 1.3.6.1.4.1.1751.2.4.3.2.6.1.3 | ||
| The Wireless MAC of this IPX Client. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| oriNetworkIPXClientStatus | 1.3.6.1.4.1.1751.2.4.3.2.6.1.4 | ||
| Flag to indicate whether the IPX Client is Active or Inactive. IPX Client status can also be disabled/enabled/deleted. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2), delete(3) | ||
| orinocoSNMP | 1.3.6.1.4.1.1751.2.4.4 | ||
| OBJECT IDENTIFIER | |||
| oriSNMPReadPassword | 1.3.6.1.4.1.1751.2.4.4.1 | ||
| This parameter represents the read-only community name used in the SNMP protocol. This parameter is used for reading objects from the SNMP agent. The default value for this object should be public. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriSNMPReadWritePassword | 1.3.6.1.4.1.1751.2.4.4.2 | ||
| This parameter represents the read-write community name used in the SNMP protocol. This parameter is used for reading and writing objects to and from the SNMP Agent. The default value for this object should be public. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriSNMPAuthorizedManagerCount | 1.3.6.1.4.1.1751.2.4.4.3 | ||
| This parameter reflects the number of entries in the SNMP IP Access Table. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriSNMPAccessTable | 1.3.6.1.4.1.1751.2.4.4.4 | ||
| This table contains the information regarding the management stations that are authorized to manage the device. The limit of this table is 20 entries. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriSNMPAccessTableEntry | |||
| oriSNMPAccessTableEntry | 1.3.6.1.4.1.1751.2.4.4.4.1 | ||
| This parameter identifies the entry in the SNMP IP Access Table. Further description on the members of this table follows. | |||
| OBJECT-TYPE | |||
| OriSNMPAccessTableEntry | |||
| oriSNMPAccessTableIndex | 1.3.6.1.4.1.1751.2.4.4.4.1.1 | ||
| This parameter indexes the entries in the SNMP IP Access Table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriSNMPAccessTableIPAddress | 1.3.6.1.4.1.1751.2.4.4.4.1.2 | ||
| This parameter represents the IP address of the management station authorized to manage the device. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriSNMPAccessTableIPMask | 1.3.6.1.4.1.1751.2.4.4.4.1.3 | ||
| This parameter represents the IP subnet mask. This parameter can be used to grant access to a complete subnet. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriSNMPAccessTableInterface | 1.3.6.1.4.1.1751.2.4.4.4.1.4 | ||
| This parameter specifies on what interface the management station will be able to perform management functions on the device. | |||
| OBJECT-TYPE | |||
| INTEGER | allInterfaces(1), ethernetIf(2), pcCardAIf(3), pcCardBIf(4) | ||
| oriSNMPAccessTableComment | 1.3.6.1.4.1.1751.2.4.4.4.1.5 | ||
| This parameter is used for an optional comment associated to the SNMP IP Access Table entry. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriSNMPAccessTableEntryStatus | 1.3.6.1.4.1.1751.2.4.4.4.1.6 | ||
| This parameter is used to enable, disable, or delete an entry in the SNMP IP Access Table. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2), delete(3) | ||
| oriSNMPTrapHostTable | 1.3.6.1.4.1.1751.2.4.4.5 | ||
| This table contains the information regarding the trap host that will receive SNMP traps sent by the device. This table is limited 10 entries. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriSNMPTrapHostTableEntry | |||
| oriSNMPTrapHostTableEntry | 1.3.6.1.4.1.1751.2.4.4.5.1 | ||
| This parameter identifies the entry in the SNMP Trap Host Table. Further description on the members of this table follows. | |||
| OBJECT-TYPE | |||
| OriSNMPTrapHostTableEntry | |||
| oriSNMPTrapHostTableIndex | 1.3.6.1.4.1.1751.2.4.4.5.1.1 | ||
| This parameter indexes the entries in the SNMP Trap Host Table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriSNMPTrapHostTableIPAddress | 1.3.6.1.4.1.1751.2.4.4.5.1.2 | ||
| This parameter represents the IP address of the management station that shall receive SNMP Traps from the device. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriSNMPTrapHostTablePassword | 1.3.6.1.4.1.1751.2.4.4.5.1.3 | ||
| This parameter represents the password that is sent with the SNMP trap messages to allow the host to accept or reject the messages. The trap host will only accept SNMP traps if this password matches the host's password. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriSNMPTrapHostTableComment | 1.3.6.1.4.1.1751.2.4.4.5.1.4 | ||
| This parameter is used for an optional comment associated to the SNMP Trap Host Table entry. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriSNMPTrapHostTableEntryStatus | 1.3.6.1.4.1.1751.2.4.4.5.1.5 | ||
| This parameter is used to enable, disable, or delete an entry in the SNMP Trap Host Table. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2), delete(3) | ||
| oriSNMPSetupStatus | 1.3.6.1.4.1.1751.2.4.4.7 | ||
| This object is used to enable or disable SNMP based management. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| orinocoFiltering | 1.3.6.1.4.1.1751.2.4.5 | ||
| OBJECT IDENTIFIER | |||
| orinocoProtocolFilter | 1.3.6.1.4.1.1751.2.4.5.1 | ||
| OBJECT IDENTIFIER | |||
| oriProtocolFilterFlag | 1.3.6.1.4.1.1751.2.4.5.1.1 | ||
| The packets with protocols listed in the protocol filter will be forwarded or dropped based on this flag. | |||
| OBJECT-TYPE | |||
| INTEGER | allow(1), deny(2) | ||
| oriProtocolFilterTable | 1.3.6.1.4.1.1751.2.4.5.1.2 | ||
| This table contains the two byte hexadecimal values of the protocols. The packets whose protocol field matches with any of the entries in this table will be forwarded or dropped based on value of oriProtocolFilterFlag. This table is limited to 256 ethernet protocols. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriProtocolFilterTableEntry | |||
| oriProtocolFilterTableEntry | 1.3.6.1.4.1.1751.2.4.5.1.2.1 | ||
| This parameter represents the entry in the protocol filter table. This is described below. | |||
| OBJECT-TYPE | |||
| OriProtocolFilterTableEntry | |||
| oriProtocolFilterTableIndex | 1.3.6.1.4.1.1751.2.4.5.1.2.1.1 | ||
| The index for protocol filter table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriProtocolFilterProtocol | 1.3.6.1.4.1.1751.2.4.5.1.2.1.2 | ||
| The value in the protocol field of the Ethernet packet. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| oriProtocolFilterProtocolComment | 1.3.6.1.4.1.1751.2.4.5.1.2.1.3 | ||
| An optional comment on the ethernet protocol to be filtered. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriProtocolFilterStatus | 1.3.6.1.4.1.1751.2.4.5.1.2.1.4 | ||
| This parameter is used to enable, disable, or delete the protocols in this table. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2), delete(3) | ||
| orinocoAccessControl | 1.3.6.1.4.1.1751.2.4.5.2 | ||
| OBJECT IDENTIFIER | |||
| oriAccessControlStatus | 1.3.6.1.4.1.1751.2.4.5.2.1 | ||
| This flag determines whether access control is enabled or disabled. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriAccessControlOperationType | 1.3.6.1.4.1.1751.2.4.5.2.2 | ||
| This flag determines whether the stations with MAC addresses listed in the access control table must be allowed or denied to access the AP. This flag is used only if oriAccessControlStatus is enabled. This table is limited to 1000 MAC Addresss entries. | |||
| OBJECT-TYPE | |||
| INTEGER | allow(1), deny(2) | ||
| oriAccessControlTable | 1.3.6.1.4.1.1751.2.4.5.2.3 | ||
| This table contains the information about MAC addresses of the wireless stations that are either allowed or disallowed access (based on oriAccessControlOperation) through this Access Point. This table is used only if oriAccessControlStatus is enabled. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriAccessControlEntry | |||
| oriAccessControlEntry | 1.3.6.1.4.1.1751.2.4.5.2.3.1 | ||
| This parameter represents the entry in the access control table. This is described below. | |||
| OBJECT-TYPE | |||
| OriAccessControlEntry | |||
| oriAccessControlTableIndex | 1.3.6.1.4.1.1751.2.4.5.2.3.1.1 | ||
| This is an index for the access control table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriAccessControlTableMACAddress | 1.3.6.1.4.1.1751.2.4.5.2.3.1.2 | ||
| MAC address of the wireless station that can access the Access Point. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| oriAccessControlTableComment | 1.3.6.1.4.1.1751.2.4.5.2.3.1.3 | ||
| This parameter is used for an optional comment associated to the access control table entry. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriAccessControlTableEntryStatus | 1.3.6.1.4.1.1751.2.4.5.2.3.1.4 | ||
| This parameter is used to enable, disable, or delete the MAC Address in the Access Control Table. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2), delete(3) | ||
| orinocoStaticMACAddressFilter | 1.3.6.1.4.1.1751.2.4.5.3 | ||
| OBJECT IDENTIFIER | |||
| oriStaticMACAddressFilterTable | 1.3.6.1.4.1.1751.2.4.5.3.1 | ||
| This table gives the MAC address of the stations on the wired and the wireless side. Both the MAC address will be given in Pair. Stations listed in the Static MAC Address filter will have no traffic forwarded by the ORiNOCO access point. This way Multicast traffic exchanged between stations or servers can be prevented, from being transmitted over the wireless medium when both stations are actually located on the wired backbone. This table is limited to 200 entries. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriStaticMACAddressFilterEntry | |||
| oriStaticMACAddressFilterEntry | 1.3.6.1.4.1.1751.2.4.5.3.1.1 | ||
| This parameter identifies the entry in the Static MAC address filter table. Further description follows. | |||
| OBJECT-TYPE | |||
| OriStaticMACAddressFilterEntry | |||
| oriStaticMACAddressFilterTableIndex | 1.3.6.1.4.1.1751.2.4.5.3.1.1.1 | ||
| This an index for the Static MAC address filter table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriStaticMACAddressFilterWiredAddress | 1.3.6.1.4.1.1751.2.4.5.3.1.1.2 | ||
| The MAC address of the station on the wired side of the Access Point. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| oriStaticMACAddressFilterWiredMask | 1.3.6.1.4.1.1751.2.4.5.3.1.1.3 | ||
| This mask determines the presence of wildcard characters in the MAC address of the station on the wired side. The value F (hex digit) in the mask indicates the presence of a wildcard character and the value 0 indicates its absence. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| oriStaticMACAddressFilterWirelessAddress | 1.3.6.1.4.1.1751.2.4.5.3.1.1.4 | ||
| The MAC address of the station on the wireless side. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| oriStaticMACAddressFilterWirelessMask | 1.3.6.1.4.1.1751.2.4.5.3.1.1.5 | ||
| The mask that determines the presence of wildcard characters in the MAC address of the station on the wireless side. The value F (hex digit) indicates the presence of a wildcard character and the hex digit 0 indicates its absense. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| oriStaticMACAddressFilterStatus | 1.3.6.1.4.1.1751.2.4.5.3.1.1.6 | ||
| This parameter is used to enable, disable, or delete the MAC Address in the Static MAC Address Table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2), delete(3) | ||
| oriStaticMACAddressFilterComment | 1.3.6.1.4.1.1751.2.4.5.3.1.1.7 | ||
| This parameter is used for an optional comment associated to the access control table entry. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| orinocoStormThreshold | 1.3.6.1.4.1.1751.2.4.5.4 | ||
| OBJECT IDENTIFIER | |||
| oriBroadcastAddressThreshold | 1.3.6.1.4.1.1751.2.4.5.4.1 | ||
| If broadcast rate from any device (identified by its MAC address) exceeds the limit specified by this value, the access point will ignore all subsequent messages issued by the particular network device, or ignore all messages of that type. Valid values for address threshold is between 0 - 255 frames per second. Initial Value is 0 (Disable Storm Threshold Protection). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| oriMulticastAddressThreshold | 1.3.6.1.4.1.1751.2.4.5.4.2 | ||
| If multicast rate from any device (identified by its MAC address) exceeds the limit specified by this value, the access point will ignore all subsequent messages issued by the particular network device, or ignore all messages of that type. Valid values for address threshold is between 0 - 255 frames per second. Initial Value is 0 (Disable Storm Threshold Protection). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| oriStormThresholdTable | 1.3.6.1.4.1.1751.2.4.5.4.3 | ||
| The table containing broadcast and multicast threshold values for each interface. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriStormThresholdTableEntry | |||
| oriStormThresholdTableEntry | 1.3.6.1.4.1.1751.2.4.5.4.3.1 | ||
| This is the entry in the protocol filter table. Described below. | |||
| OBJECT-TYPE | |||
| OriStormThresholdTableEntry | |||
| oriStormThresholdIfBroadcast | 1.3.6.1.4.1.1751.2.4.5.4.3.1.1 | ||
| This parameter specifies a set of Broadcast Storm thresholds for each interface/port of the access point, identifying separate values for the number of Broadcast messages/second. Default value is zero, which means disabled. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..9999 | ||
| oriStormThresholdIfMulticast | 1.3.6.1.4.1.1751.2.4.5.4.3.1.2 | ||
| This parameter specifies a set of Multicast Storm thresholds for each interface/port of the access point, identifying separate values for the number of Multicast messages/second. Default value is zero, which means disabled. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..9999 | ||
| orinocoAdvancedFiltering | 1.3.6.1.4.1.1751.2.4.5.5 | ||
| OBJECT IDENTIFIER | |||
| oriBroadcastFilteringTable | 1.3.6.1.4.1.1751.2.4.5.5.1 | ||
| The table entries for broadcast filters. This table shall contain 5 entries. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriBroadcastFilteringTableEntry | |||
| oriBroadcastFilteringTableEntry | 1.3.6.1.4.1.1751.2.4.5.5.1.1 | ||
| This object represents an entry in the broadcast filtering table. | |||
| OBJECT-TYPE | |||
| OriBroadcastFilteringTableEntry | |||
| oriBroadcastFilteringTableIndex | 1.3.6.1.4.1.1751.2.4.5.5.1.1.1 | ||
| This object represents the index of the Broadcast Filtering table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriBroadcastFilteringProtocolName | 1.3.6.1.4.1.1751.2.4.5.5.1.1.2 | ||
| This object represents the broadcast protocol name to be filtered. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriBroadcastFilteringDirection | 1.3.6.1.4.1.1751.2.4.5.5.1.1.3 | ||
| This object represents the direction of the broadcast fiter. The filter can be enabled for Ethernet to Wireless, Wireless to Ethernet, or both. | |||
| OBJECT-TYPE | |||
| INTEGER | ethernetToWireless(1), wirelessToEthernet(2), both(3) | ||
| oriBroadcastFilteringStatus | 1.3.6.1.4.1.1751.2.4.5.5.1.1.4 | ||
| This object is used to enable or disable the broadcast filter. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| orinocoRADIUS | 1.3.6.1.4.1.1751.2.4.6 | ||
| OBJECT IDENTIFIER | |||
| orinocoRADIUSAuth | 1.3.6.1.4.1.1751.2.4.6.1 | ||
| OBJECT IDENTIFIER | |||
| oriRADIUSAuthServerTable | 1.3.6.1.4.1.1751.2.4.6.1.1 | ||
| This table represents the RADIUS servers that the device will communicated with for authentication. Usually this table should have two members representing the primary and secondary or backup RADIUS Authentication Servers. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriRADIUSAuthServerTableEntry | |||
| oriRADIUSAuthServerTableEntry | 1.3.6.1.4.1.1751.2.4.6.1.1.1 | ||
| This parameter represents the entry into the RADIUS Authentication Server Table. | |||
| OBJECT-TYPE | |||
| OriRADIUSAuthServerTableEntry | |||
| oriRADIUSAuthServerTableIndex | 1.3.6.1.4.1.1751.2.4.6.1.1.1.1 | ||
| This parameter represents a unique value for each RADIUS table entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriRADIUSAuthServerType | 1.3.6.1.4.1.1751.2.4.6.1.1.1.2 | ||
| This parameter indicates if the RADIUS server will provide Authentication service, Accounting service, or both. | |||
| OBJECT-TYPE | |||
| INTEGER | authentication(1), accounting(2), authAndAcct(3) | ||
| oriRADIUSAuthServerStatus | 1.3.6.1.4.1.1751.2.4.6.1.1.1.3 | ||
| This parameter identifies if the RADIUS server entry is enabled or disabled. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2), delete(3) | ||
| oriRADIUSAuthServerIPAddress | 1.3.6.1.4.1.1751.2.4.6.1.1.1.4 | ||
| This parameter represents the IP address of the RADIUS server. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriRADIUSAuthServerDestPort | 1.3.6.1.4.1.1751.2.4.6.1.1.1.5 | ||
| This parameter represents the RADIUS server authentication port - the default value is 1812. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriRADIUSAuthServerSharedSecret | 1.3.6.1.4.1.1751.2.4.6.1.1.1.6 | ||
| This parameter represents the shared secret between the RADIUS server and client. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriRADIUSAuthServerResponseTime | 1.3.6.1.4.1.1751.2.4.6.1.1.1.7 | ||
| This parameter represents the time, in seconds, for which the RADIUS client will wait, until another authentication request is sent to the server. The default value for this object should be 3. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..10 | ||
| oriRADIUSAuthServerMaximumRetransmission | 1.3.6.1.4.1.1751.2.4.6.1.1.1.8 | ||
| This parameter represents the number of retransmissions of authentication requests by the RADIUS Client to the Server. The default value for this object should be 3. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..4 | ||
| oriRADIUSAuthClientAccessRequests | 1.3.6.1.4.1.1751.2.4.6.1.1.1.9 | ||
| This parameter represents the number of RADIUS Access Requests messages transmitted from the client to the server since client startup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriRADIUSAuthClientAccessRetransmissions | 1.3.6.1.4.1.1751.2.4.6.1.1.1.10 | ||
| This parameter represents the number of RADIUS Access Requests retransmitted by the client to the server since client startup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriRADIUSAuthClientAccessAccepts | 1.3.6.1.4.1.1751.2.4.6.1.1.1.11 | ||
| This parameter indicates the number of RADIUS Access Accept messages received since client startup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriRADIUSAuthClientAccessChallenges | 1.3.6.1.4.1.1751.2.4.6.1.1.1.12 | ||
| This variable represents the number of RADIUS Access Challenges messages received since client startup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriRADIUSAuthClientAccessRejects | 1.3.6.1.4.1.1751.2.4.6.1.1.1.13 | ||
| This variable represents the number of RADIUS Access Rejects messages received since client startup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriRADIUSAuthClientMalformedAccessResponses | 1.3.6.1.4.1.1751.2.4.6.1.1.1.14 | ||
| This variable represents the number of malformed RADIUS Access Response messages received since client startup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriRADIUSAuthClientAuthInvalidAuthenticators | 1.3.6.1.4.1.1751.2.4.6.1.1.1.15 | ||
| This variable represents the number of malformed RADIUS Access Response messages containing invalid authenticators received since client startup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriRADIUSAuthClientTimeouts | 1.3.6.1.4.1.1751.2.4.6.1.1.1.16 | ||
| This variable represents the total number of timeouts for RADIUS Access Request messages since client startup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| orinocoRADIUSAcct | 1.3.6.1.4.1.1751.2.4.6.2 | ||
| OBJECT IDENTIFIER | |||
| oriRADIUSAcctServerTable | 1.3.6.1.4.1.1751.2.4.6.2.1 | ||
| This table represents the RADIUS servers that the device will communicated with for accounting. Usually this table should have two members representing the primary and secondary or backup RADIUS Accounting Servers. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriRADIUSAcctServerTableEntry | |||
| oriRADIUSAcctServerTableEntry | 1.3.6.1.4.1.1751.2.4.6.2.1.1 | ||
| This parameter represents the entry into the RADIUS Accouting Server Table. | |||
| OBJECT-TYPE | |||
| OriRADIUSAcctServerTableEntry | |||
| oriRADIUSAcctServerTableIndex | 1.3.6.1.4.1.1751.2.4.6.2.1.1.1 | ||
| This parameter represents a unique value for each RADIUS table entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriRADIUSAcctServerType | 1.3.6.1.4.1.1751.2.4.6.2.1.1.2 | ||
| This parameter indicates if the RADIUS server will provide Authentication service, Accounting service, or both. | |||
| OBJECT-TYPE | |||
| INTEGER | authentication(1), accounting(2), authAndAcct(3) | ||
| oriRADIUSAcctServerStatus | 1.3.6.1.4.1.1751.2.4.6.2.1.1.3 | ||
| This parameter identifies if the RADIUS server entry is enabled or disabled. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2), delete(3) | ||
| oriRADIUSAcctServerIPAddress | 1.3.6.1.4.1.1751.2.4.6.2.1.1.4 | ||
| This parameter represents the IP address of the RADIUS server. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriRADIUSAcctServerDestPort | 1.3.6.1.4.1.1751.2.4.6.2.1.1.5 | ||
| This parameter represents the RADIUS server accounting port - the default value is 1813. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriRADIUSAcctServerSharedSecret | 1.3.6.1.4.1.1751.2.4.6.2.1.1.6 | ||
| This parameter represents the shared secret between the RADIUS server and client. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriRADIUSAcctServerResponseTime | 1.3.6.1.4.1.1751.2.4.6.2.1.1.7 | ||
| This parameter represents the time, in seconds, for which the RADIUS client will wait, until another authentication request is sent to the server. The default value for this object should be 3. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..10 | ||
| oriRADIUSAcctServerMaximumRetransmission | 1.3.6.1.4.1.1751.2.4.6.2.1.1.8 | ||
| This parameter represents the number of retransmissions of authentication requests by the RADIUS Client to the Server. The default value for this object should be 3. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..4 | ||
| oriRADIUSAcctClientAccountingRequests | 1.3.6.1.4.1.1751.2.4.6.2.1.1.9 | ||
| This parameter represents the number of Accounting Requests messages sent since client startup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriRADIUSAcctClientAccountingRetransmissions | 1.3.6.1.4.1.1751.2.4.6.2.1.1.10 | ||
| This parameter represents the number of Accounting Requests messages retransmitted sent since client startup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriRADIUSAcctClientAccountingResponses | 1.3.6.1.4.1.1751.2.4.6.2.1.1.11 | ||
| This parameter represents the number of Accounting Response messages received since client startup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriRADIUSAcctClientAcctInvalidAuthenticators | 1.3.6.1.4.1.1751.2.4.6.2.1.1.12 | ||
| This parameter represents the number of Accounting Response messages which contain invalid authenticators received since client startup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriRADIUSClientInvalidServerAddress | 1.3.6.1.4.1.1751.2.4.6.3 | ||
| This counter represents the total number of RADIUS access-response messages received from an unknown address since client start-up. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriRADIUSMACAccessControl | 1.3.6.1.4.1.1751.2.4.6.4 | ||
| Enables RADIUS ACCESS CONTROL based on stations MAC Address. The default value for this object should be disable. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriRADIUSAuthorizationLifeTime | 1.3.6.1.4.1.1751.2.4.6.5 | ||
| This object is the authorization lifetime for a certain MAC based RADIUS authenticated client. The default value for this parameter is 2 hours = 7200 seconds. The units for this object is seconds. | |||
| OBJECT-TYPE | |||
| Integer32 | 900..43200 | ||
| orinocoTelnet | 1.3.6.1.4.1.1751.2.4.7 | ||
| OBJECT IDENTIFIER | |||
| oriTelnetSessions | 1.3.6.1.4.1.1751.2.4.7.1 | ||
| This object is used to enable or disable telnet access and to specify the number of active telnet sessions. When this object is set to 0, telnet access is disabled. When this object is set to something greater than 0, then it specifies the maximum number of active telnet sessions. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..5 | ||
| oriTelnetPassword | 1.3.6.1.4.1.1751.2.4.7.2 | ||
| This parameter is the password to access the device via telnet. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriTelnetPort | 1.3.6.1.4.1.1751.2.4.7.3 | ||
| This parameter represents the TCP/IP port for which the telnet daemon will be accessible. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriTelnetLoginTimeout | 1.3.6.1.4.1.1751.2.4.7.4 | ||
| This parameter represents the login timeout in seconds - the default value is 30 seconds. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..300 | ||
| oriTelnetIdleTimeout | 1.3.6.1.4.1.1751.2.4.7.5 | ||
| This parameter represents the inactivity or idle timeout in minutes - the default value is 15 minutes. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..36000 | ||
| orinocoTFTP | 1.3.6.1.4.1.1751.2.4.8 | ||
| OBJECT IDENTIFIER | |||
| oriTFTPServerIPAddress | 1.3.6.1.4.1.1751.2.4.8.1 | ||
| This variable represents the IP address of the TFTP server. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriTFTPFileName | 1.3.6.1.4.1.1751.2.4.8.2 | ||
| This parameter represents the filename to upload or download to the TFTP server. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriTFTPFileType | 1.3.6.1.4.1.1751.2.4.8.3 | ||
| This parameter is used for the device to know what type of file is being uploaded or downloaded. | |||
| OBJECT-TYPE | |||
| INTEGER | configSys(1), image(2), orinoco(3), radius(4), snmpset(5), sysinfo(6), ppp(7), bspbl(8) | ||
| oriTFTPOperation | 1.3.6.1.4.1.1751.2.4.8.4 | ||
| This parameter represents the TFTP operation to be executed. The upload function shall transfer the specified file from the ORiNOCO device to the TFTP server. The download function shall transfer the specified file from the TFTP server to the ORiNOCO device. The upload function shall transfer the specified file from the ORiNOCO device to the TFTP server. The download and reboot function, will perform the download and then reboot the device. | |||
| OBJECT-TYPE | |||
| INTEGER | upload(1), download(2), downloadAndReboot(3) | ||
| oriTFTPOperationStatus | 1.3.6.1.4.1.1751.2.4.8.5 | ||
| This parameter represents the TFTP operation status. When a TFTP operation is idle (not in progress) this object will be set to 1. When a TFTP operation is in progress this object will be set to 2. When a TFTP operation has been successful this object will be set to 3. When a TFTP operation has failed this object will be set to 4. | |||
| OBJECT-TYPE | |||
| INTEGER | idle(1), inProgress(2), successful(3), failure(4) | ||
| orinocoSerial | 1.3.6.1.4.1.1751.2.4.9 | ||
| OBJECT IDENTIFIER | |||
| oriSerialBaudRate | 1.3.6.1.4.1.1751.2.4.9.1 | ||
| This parameter represents the baud rate for the serial interface - the default value is 9600. | |||
| OBJECT-TYPE | |||
| INTEGER | baud2400(1), baud4800(2), baud9600(3), baud19200(4), baud38400(5), baud57600(6) | ||
| oriSerialDataBits | 1.3.6.1.4.1.1751.2.4.9.2 | ||
| This parameter represents the serial interface data bits - the default value is 8. | |||
| OBJECT-TYPE | |||
| Integer32 | 4..8 | ||
| oriSerialParity | 1.3.6.1.4.1.1751.2.4.9.3 | ||
| This parameter is used for the serial interface parity check - the default value is none. | |||
| OBJECT-TYPE | |||
| INTEGER | even(1), odd(2), none(3), mark(4), space(5) | ||
| oriSerialStopBits | 1.3.6.1.4.1.1751.2.4.9.4 | ||
| This parameter indicates the serial interface stop bits - the default value is 1. | |||
| OBJECT-TYPE | |||
| INTEGER | bit1(1), bit1dot5(2), bit2(3) | ||
| oriSerialFlowControl | 1.3.6.1.4.1.1751.2.4.9.5 | ||
| This parameter is used for the serial interface flow control - the default value is none. | |||
| OBJECT-TYPE | |||
| INTEGER | xonxoff(1), none(2) | ||
| orinocoIAPP | 1.3.6.1.4.1.1751.2.4.10 | ||
| OBJECT IDENTIFIER | |||
| oriIAPPStatus | 1.3.6.1.4.1.1751.2.4.10.1 | ||
| This parameter is used to enable or disable the IAPP feature. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriIAPPPeriodicAnnounceInterval | 1.3.6.1.4.1.1751.2.4.10.2 | ||
| This parameter represents interval in seconds for performing an IAPP announce operation by the device. The default value for this parameter should be 120 seconds. | |||
| OBJECT-TYPE | |||
| INTEGER | eighty(80), oneHundredTwenty(120), oneHundredSixty(160), twoHundred(200) | ||
| oriIAPPAnnounceResponseTime | 1.3.6.1.4.1.1751.2.4.10.3 | ||
| This parameter indicates the amount of time in seconds the device waits to send an IAPP announce response after an announce request message is sent. This parameter is set to a default value of 2 seconds and is not configurable. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriIAPPHandoverTimeout | 1.3.6.1.4.1.1751.2.4.10.4 | ||
| This parameter represents the time in milliseconds the device waits before it resends a handover response message. The default value for this parameter should be 512 milliseconds. This parameter is originally given in kuseconds, but has been converted to milliseconds. | |||
| OBJECT-TYPE | |||
| INTEGER | fourHundredTen(410), fiveHundredTwelve(512), sixHundredFourteen(614), sevenHundredSeventeen(717), eightHundredNineteen(819) | ||
| oriIAPPMaximumHandoverRetransmissions | 1.3.6.1.4.1.1751.2.4.10.5 | ||
| This parameter indicates the maximum amount of retransmission sent by the device for a handover request message. The default for this parameter should be 2. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..4 | ||
| oriIAPPAnnounceRequestSent | 1.3.6.1.4.1.1751.2.4.10.6 | ||
| This parameter represents the total number of IAPP Announce Request Messages sent since bootup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriIAPPAnnounceRequestReceived | 1.3.6.1.4.1.1751.2.4.10.7 | ||
| This parameter represents the total number of IAPP Announce Request Messages received since bootup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriIAPPAnnounceResponseSent | 1.3.6.1.4.1.1751.2.4.10.8 | ||
| This parameter represents the total number of IAPP Announce Response Messages sent since bootup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriIAPPAnnounceResponseReceived | 1.3.6.1.4.1.1751.2.4.10.9 | ||
| This parameter represents the total number of IAPP Announce Response Messages received since bootup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriIAPPHandoverRequestSent | 1.3.6.1.4.1.1751.2.4.10.10 | ||
| This parameter represents the total number of IAPP Handover Request messages sent since bootup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriIAPPHandoverRequestReceived | 1.3.6.1.4.1.1751.2.4.10.11 | ||
| This parameter represents the total number of IAPP Handover Request messages received since bootup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriIAPPHandoverRequestRetransmissions | 1.3.6.1.4.1.1751.2.4.10.12 | ||
| This parameter represents the total number of IAPP Handover Request retransmissions since bootup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriIAPPHandoverResponseSent | 1.3.6.1.4.1.1751.2.4.10.13 | ||
| This parameter represents the total number of IAPP Handover Response messages sent since bootup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriIAPPHandoverResponseReceived | 1.3.6.1.4.1.1751.2.4.10.14 | ||
| This parameter represents the total number of IAPP Handover Response messages received since bootup. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriIAPPPDUsDropped | 1.3.6.1.4.1.1751.2.4.10.15 | ||
| This parameter represents the total number of IAPP packets dropped due to erroneous information within the packet. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriIAPPRoamingClients | 1.3.6.1.4.1.1751.2.4.10.16 | ||
| This parameter represents the total number of client that have roamed from one device to another. This parameter is per ORiNOCO device and not a total counter of all the roaming clients for all ORiNOCO devices on the network. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriIAPPTerminatePPPSessionPDUsSent | 1.3.6.1.4.1.1751.2.4.10.17 | ||
| This variable represents a count of the terminate PPP Session PDUs sent. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriIAPPTerminatePPPSessionPDUsReceived | 1.3.6.1.4.1.1751.2.4.10.18 | ||
| This variable represents a count of the terminate PPP Session PDUs received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriIAPPTerminatePPPSessionACKsSent | 1.3.6.1.4.1.1751.2.4.10.19 | ||
| This object represents the number of terminate PPP Session acknowledgement PDUs sent. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriIAPPTerminatePPPSessionACKsReceived | 1.3.6.1.4.1.1751.2.4.10.20 | ||
| This object represents the number of terminate PPP Session acknowledgement PDUs received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriIAPPMACIPTable | 1.3.6.1.4.1.1751.2.4.10.21 | ||
| The (conceptual) table listing Access Server 2000 devices in the same subnet that have the IAPP function enabled. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriIAPPMACIPTableEntry | |||
| oriIAPPMACIPTableEntry | 1.3.6.1.4.1.1751.2.4.10.21.1 | ||
| An entry (conceptual row) representing an Access Server 2000 device, maintaining its IP address and Wireless MAC Address. | |||
| OBJECT-TYPE | |||
| OriIAPPMACIPTableEntry | |||
| oriIAPPMACIPTableIndex | 1.3.6.1.4.1.1751.2.4.10.21.1.1 | ||
| The index for the IAPP MAC-IP table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriIAPPMACIPTableSystemName | 1.3.6.1.4.1.1751.2.4.10.21.1.2 | ||
| The System Name of the IAPP enabled ORiNOCO device. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriIAPPMACIPTableIPAddress | 1.3.6.1.4.1.1751.2.4.10.21.1.3 | ||
| The IP Address of the IAPP enabled ORiNOCO device. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriIAPPMACIPTableBSSID | 1.3.6.1.4.1.1751.2.4.10.21.1.4 | ||
| The BSSID (MAC address of wireless interface) of the IAPP enabled ORiNOCO device. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| oriIAPPMACIPTableESSID | 1.3.6.1.4.1.1751.2.4.10.21.1.5 | ||
| The ESSID (network name) of the IAPP enabled ORiNOCO device. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriIAPPSendAnnounceRequestOnStart | 1.3.6.1.4.1.1751.2.4.10.22 | ||
| Flag to determine whether to send announce request on start. Default value is enable. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| orinocoLinkTest | 1.3.6.1.4.1.1751.2.4.11 | ||
| OBJECT IDENTIFIER | |||
| oriLinkTestTimeOut | 1.3.6.1.4.1.1751.2.4.11.1 | ||
| The value of this parameter determines the time (in seconds)that a link test will continue without any SNMP requests for a Link Test Table entry. When the time expires the Link Test Table is cleared. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestInterval | 1.3.6.1.4.1.1751.2.4.11.3 | ||
| This parameter indicates the interval (in millisec) between sending link test frames to a station. Default on 200 millisecond. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestExplore | 1.3.6.1.4.1.1751.2.4.11.4 | ||
| When this parameter is set to 2, the access point will send out an explore request on all 802.11 interfaces and from the results build the Link Test table. This table is valid only while this parameter is 3. | |||
| OBJECT-TYPE | |||
| INTEGER | tableTimedOut(1), exploring(2), exploreResultsAvailable(3) | ||
| oriLinkTestTable | 1.3.6.1.4.1.1751.2.4.11.5 | ||
| This table contains the information for the stations currently associated with this access point. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriLinkTestTableEntry | |||
| oriLinkTestTableEntry | 1.3.6.1.4.1.1751.2.4.11.5.1 | ||
| This parameter represents the entry in the Remote Link Test table. This is described below. | |||
| OBJECT-TYPE | |||
| OriLinkTestTableEntry | |||
| oriLinkTestTableIndex | 1.3.6.1.4.1.1751.2.4.11.5.1.1 | ||
| This parameter represents a unique value for each stattion. The value for each station must remain constant at least from one explore to the next. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestInProgress | 1.3.6.1.4.1.1751.2.4.11.5.1.2 | ||
| When this parameter is set to 2 the access point will initiate a link test sequence with this station. | |||
| OBJECT-TYPE | |||
| INTEGER | noLinkTestInProgress(1), linkTestIinProgress(2) | ||
| oriLinkTestStationName | 1.3.6.1.4.1.1751.2.4.11.5.1.3 | ||
| This parameter identifies the name of the station whom which the link test is being performed. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriLinkTestMACAddress | 1.3.6.1.4.1.1751.2.4.11.5.1.4 | ||
| This variable represents the MAC address that will be mapped to the IP Address of the station. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| oriLinkTestStationProfile | 1.3.6.1.4.1.1751.2.4.11.5.1.5 | ||
| This parameter represents the profile/capabilities for this station. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestOurCurSignalLevel | 1.3.6.1.4.1.1751.2.4.11.5.1.6 | ||
| The current signal level (in dB) for the link test from this station. This variable indicates the running average of the local signal level using the algorithm (3/4*oldvalue + 1/4*newvalue). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestOurCurNoiseLevel | 1.3.6.1.4.1.1751.2.4.11.5.1.7 | ||
| The current noise level (in dB) for the link test to this station. This variable indicates the running average of the local noise level. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestOurCurSNR | 1.3.6.1.4.1.1751.2.4.11.5.1.8 | ||
| The current signal to noise ratio for the link test to this station. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestOurMinSignalLevel | 1.3.6.1.4.1.1751.2.4.11.5.1.9 | ||
| The minimum signal level during the link test to this station. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestOurMinNoiseLevel | 1.3.6.1.4.1.1751.2.4.11.5.1.10 | ||
| The minimum noise level during the link test to this station. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestOurMinSNR | 1.3.6.1.4.1.1751.2.4.11.5.1.11 | ||
| The minimum signal to noise ratio during the link test to this station. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestOurMaxSignalLevel | 1.3.6.1.4.1.1751.2.4.11.5.1.12 | ||
| The maximum signal level during the link test to this station. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestOurMaxNoiseLevel | 1.3.6.1.4.1.1751.2.4.11.5.1.13 | ||
| The maximum noise level during the link test to this station. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestOurMaxSNR | 1.3.6.1.4.1.1751.2.4.11.5.1.14 | ||
| The maximum signal to noise ratio during the link test to this station. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestOurLowFrameCount | 1.3.6.1.4.1.1751.2.4.11.5.1.15 | ||
| The total number of frames sent at 1 Mbit/s speed during the link test to this station. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestOurStandardFrameCount | 1.3.6.1.4.1.1751.2.4.11.5.1.16 | ||
| The total number of frames sent at 2 Mbit/s speed during the link test to this station. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestOurMediumFrameCount | 1.3.6.1.4.1.1751.2.4.11.5.1.17 | ||
| The total number of frames sent at 5.5 Mbit/s (for Turbo-8, it is 5 Mbit/s) speed during the link test to this station. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestOurHighFrameCount | 1.3.6.1.4.1.1751.2.4.11.5.1.18 | ||
| The total number of frames sent at 11 Mbit/s (for Turbo-8, it is 8 Mbit/s) speed during the link test to this station. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestHisCurSignalLevel | 1.3.6.1.4.1.1751.2.4.11.5.1.19 | ||
| The current signal level for the link test to the remote station or access point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestHisCurNoiseLevel | 1.3.6.1.4.1.1751.2.4.11.5.1.20 | ||
| The current noise level for the link test to the remote station or access point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestHisCurSNR | 1.3.6.1.4.1.1751.2.4.11.5.1.21 | ||
| The current signal to noise ratio for the link test to the remote station or access point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestHisMinSignalLevel | 1.3.6.1.4.1.1751.2.4.11.5.1.22 | ||
| The minimum signal level during the link test to the remote statio or access point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestHisMinNoiseLevel | 1.3.6.1.4.1.1751.2.4.11.5.1.23 | ||
| The minimum noise level during the link test to the remote station or access point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestHisMinSNR | 1.3.6.1.4.1.1751.2.4.11.5.1.24 | ||
| The minimum signal to noise ratio during the link test to the remote station or access point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestHisMaxSignalLevel | 1.3.6.1.4.1.1751.2.4.11.5.1.25 | ||
| The maximum signal level during the link test to the remote station or access point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestHisMaxNoiseLevel | 1.3.6.1.4.1.1751.2.4.11.5.1.26 | ||
| The maximum noise level during the link test to the remote station or access point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestHisMaxSNR | 1.3.6.1.4.1.1751.2.4.11.5.1.27 | ||
| The maximum signal to noise ratio during the link test to the remote station or access point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestHisLowFrameCount | 1.3.6.1.4.1.1751.2.4.11.5.1.28 | ||
| The total number of frames sent at 1 Mbit/s speed during the link test to the remote station or access point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestHisStandardFrameCount | 1.3.6.1.4.1.1751.2.4.11.5.1.29 | ||
| The total number of frames sent at 2 Mbit/s speed during the link test to the remote station or access point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestHisMediumFrameCount | 1.3.6.1.4.1.1751.2.4.11.5.1.30 | ||
| The total number of frames sent at 5.5 Mbit/s (for Turbo-8, it is 5 Mbit/s) speed during the link test to the remote station or access point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestHisHighFrameCount | 1.3.6.1.4.1.1751.2.4.11.5.1.31 | ||
| The total number of frames sent at 11 Mbit/s (for Turbo-8, it is 5 Mbit/s) speed during the link test to the remote station or access point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkTestInterface | 1.3.6.1.4.1.1751.2.4.11.5.1.32 | ||
| The PCMCIA Card Number to which the Client has sent the Explore Response Message. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriLinkTestRadioType | 1.3.6.1.4.1.1751.2.4.11.5.1.33 | ||
| The Wireless Standard eg. IEEE 802.11 or IEEE 802.11b used on the Radio. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| orinocoLinkInt | 1.3.6.1.4.1.1751.2.4.12 | ||
| OBJECT IDENTIFIER | |||
| oriLinkIntStatus | 1.3.6.1.4.1.1751.2.4.12.1 | ||
| This parameter is used to enable or disable the link integrity functionality. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriLinkIntPollInterval | 1.3.6.1.4.1.1751.2.4.12.2 | ||
| This parameter is used to set the poll interval (in milliseconds) for the link integrity check. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkIntPollRetransmissions | 1.3.6.1.4.1.1751.2.4.12.3 | ||
| This parameter is used to set the number of retransmissions for the link integrity check. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkIntTable | 1.3.6.1.4.1.1751.2.4.12.4 | ||
| This table contains the target IP addresses in order to perform the link integrity check. This table is limited to 5 entries. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriLinkIntTableEntry | |||
| oriLinkIntTableEntry | 1.3.6.1.4.1.1751.2.4.12.4.1 | ||
| This parameter identifies the entry in the link integrity target table. Further description on the members of this table follows. | |||
| OBJECT-TYPE | |||
| OriLinkIntTableEntry | |||
| oriLinkIntTableIndex | 1.3.6.1.4.1.1751.2.4.12.4.1.1 | ||
| This parameter indexes the entries in the link integrity target table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriLinkIntTableTargetIPAddress | 1.3.6.1.4.1.1751.2.4.12.4.1.2 | ||
| This parameter represents the IP address of the target machine for the link integrity check. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriLinkIntTableComment | 1.3.6.1.4.1.1751.2.4.12.4.1.3 | ||
| This parameter is used for an optional comment associated to the link integrity table entry. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriLinkIntTableEntryStatus | 1.3.6.1.4.1.1751.2.4.12.4.1.4 | ||
| This parameter is used to enable, disable, or delete an entry in the link integrity table. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2), delete(3) | ||
| orinocoECP | 1.3.6.1.4.1.1751.2.4.13 | ||
| OBJECT IDENTIFIER | |||
| oriECPRetransmissionCount | 1.3.6.1.4.1.1751.2.4.13.1 | ||
| This object represents the number of retransmissions when responses are not received within the timeout period. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriECPResponseRetransmissions | 1.3.6.1.4.1.1751.2.4.13.2 | ||
| This parameter represents the number of times the transmitted response can be retransmitted. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriECPResponseRetransmissionTimeout | 1.3.6.1.4.1.1751.2.4.13.3 | ||
| This variable represents the timeout interval for a response to be received. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| orinocoPPP | 1.3.6.1.4.1.1751.2.4.14 | ||
| OBJECT IDENTIFIER | |||
| oriPPPIPAddressAssignmentType | 1.3.6.1.4.1.1751.2.4.14.1 | ||
| This variable identifies whether the IP addresses assigned to the AS-Clients are obtained from the local address pool, from DHCP Server via DHCP Relay, or from the RADIUS server. The default value for this object is local. | |||
| OBJECT-TYPE | |||
| INTEGER | local(1), dhcpRelay(2), radius(3) | ||
| oriPPPMACtoIPMappingCount | 1.3.6.1.4.1.1751.2.4.14.2 | ||
| This variable represents the number of MAC address to IP address static mappings are present in the MAC to IP Mapping Table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriPPPMACtoIPMappingTable | 1.3.6.1.4.1.1751.2.4.14.3 | ||
| This table contains the static mapping of MAC addresses to IP addresses. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriPPPMACtoIPMappingTableEntry | |||
| oriPPPMACtoIPMappingTableEntry | 1.3.6.1.4.1.1751.2.4.14.3.1 | ||
| This object represents the entry of the MAC to IP Address mapping table. The members of this table are described below. | |||
| OBJECT-TYPE | |||
| OriPPPMACtoIPMappingTableEntry | |||
| oriPPPMACtoIPTableIndex | 1.3.6.1.4.1.1751.2.4.14.3.1.1 | ||
| This represents the index to the IP to MAC address mapping table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriPPPMACtoIPTableMACAddress | 1.3.6.1.4.1.1751.2.4.14.3.1.2 | ||
| This variable represents the MAC address that will be mapped to the IP Address. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| oriPPPMACtoIPTableIPAddress | 1.3.6.1.4.1.1751.2.4.14.3.1.3 | ||
| This objects identifies IP address corresponding to the MAC address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriPPPMACtoIPTableComment | 1.3.6.1.4.1.1751.2.4.14.3.1.4 | ||
| The variable represents the comment for this entry. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriPPPMACtoIPTableEntryStatus | 1.3.6.1.4.1.1751.2.4.14.3.1.5 | ||
| This variable is used to enable, disable, or delete the table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2), delete(3) | ||
| oriPPPKeepAliveInterval | 1.3.6.1.4.1.1751.2.4.14.4 | ||
| This variable represents the keep alive interval to be notified to the PPP layer. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriPPPNumKeepAliveTimeouts | 1.3.6.1.4.1.1751.2.4.14.5 | ||
| This object represents the maximum number of timeouts before the PPP session is brought down. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriPPPSessionIdleTimeout | 1.3.6.1.4.1.1751.2.4.14.6 | ||
| This variable indicates the idle timeout in order to disconnect an idle PPP client. The units for this paramter is seconds. The default value for this object should be ... | |||
| OBJECT-TYPE | |||
| Integer32 | 0..36000 | ||
| oriPPPPrimaryDNSIPAddress | 1.3.6.1.4.1.1751.2.4.14.7 | ||
| This variable represents the IP address of the primary DNS server in the network. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriPPPSecondaryDNSIPAddress | 1.3.6.1.4.1.1751.2.4.14.8 | ||
| This variable represents the IP address of the secondary DNS server in the network. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriPPPMaxNumberOfUsers | 1.3.6.1.4.1.1751.2.4.14.9 | ||
| This variable represents the number of user allowed to connect to the device. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriPPPIPPoolTableEntries | 1.3.6.1.4.1.1751.2.4.14.10 | ||
| This variable represents the number of entries in the PPP IP Address Pool Table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriPPPCHAPStatus | 1.3.6.1.4.1.1751.2.4.14.11 | ||
| This variable indicates the status of CHAP in the accessServer. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriPPPCHAPPriority | 1.3.6.1.4.1.1751.2.4.14.12 | ||
| This variable indicates the priority of CHAP among all authentictaion protocols enabled on the Access Server. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriPPPPAPStatus | 1.3.6.1.4.1.1751.2.4.14.13 | ||
| This variable indicates the status of PAP in the accessServer. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriPPPPAPPriority | 1.3.6.1.4.1.1751.2.4.14.14 | ||
| This variable indicates the priority of PAP among all authentictaion protocols enabled on the accessServer. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriPPPPrimaryWINSIPAddress | 1.3.6.1.4.1.1751.2.4.14.15 | ||
| The IP address of the Primary WINS or NBNS server in the network. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriPPPSecondaryWINSIPAddress | 1.3.6.1.4.1.1751.2.4.14.16 | ||
| The IP address of the Secondary WINS or NBNS server in the network. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriPPPIPPoolTable | 1.3.6.1.4.1.1751.2.4.14.17 | ||
| This table contains the static mapping of MAC addresses to IP addresses. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriPPPIPPoolTableEntry | |||
| oriPPPIPPoolTableEntry | 1.3.6.1.4.1.1751.2.4.14.17.1 | ||
| The entry of the oriPPPIPPoolTable. Described below. | |||
| OBJECT-TYPE | |||
| OriPPPIPPoolTableEntry | |||
| oriPPPIPPoolTableIndex | 1.3.6.1.4.1.1751.2.4.14.17.1.1 | ||
| This is the index for the IP range table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriPPPIPPoolTableStartIPAddress | 1.3.6.1.4.1.1751.2.4.14.17.1.2 | ||
| This is the starting IP address of this range. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriPPPIPPoolTableEndIPAddress | 1.3.6.1.4.1.1751.2.4.14.17.1.3 | ||
| This is the ending IP address of this range. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriPPPIPPoolTableWidth | 1.3.6.1.4.1.1751.2.4.14.17.1.4 | ||
| This is the width of the range (no of addresses). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriPPPIPPoolTableComment | 1.3.6.1.4.1.1751.2.4.14.17.1.5 | ||
| The variable represents the comment for this entry. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriPPPIPPoolTableEntryStatus | 1.3.6.1.4.1.1751.2.4.14.17.1.6 | ||
| The status of the entry, whether to be used or not used. Setting this to delete will remove this entry. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2), delete(3) | ||
| orinocoDHCP | 1.3.6.1.4.1.1751.2.4.15 | ||
| OBJECT IDENTIFIER | |||
| oriDHCPServerStatus | 1.3.6.1.4.1.1751.2.4.15.1 | ||
| This parameter indicates if the DHCP server is enabled or disabled in the ORiNOCO device. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriDHCPServerIPPoolTable | 1.3.6.1.4.1.1751.2.4.15.2 | ||
| This table contains the pool of IP Addresses that the DHCP server will assign to the DHCP clients. This table is limited to 20. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriDHCPServerIPPoolTableEntry | |||
| oriDHCPServerIPPoolTableEntry | 1.3.6.1.4.1.1751.2.4.15.2.1 | ||
| The entries in the DHCP IP Address Pool Table. Described below. | |||
| OBJECT-TYPE | |||
| OriDHCPServerIPPoolTableEntry | |||
| oriDHCPServerIPPoolTableIndex | 1.3.6.1.4.1.1751.2.4.15.2.1.1 | ||
| This is the index for the IP range table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriDHCPServerIPPoolTableStartIPAddress | 1.3.6.1.4.1.1751.2.4.15.2.1.2 | ||
| This variable represents the start IP address for this DHCP IP Address IP Pool Table entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriDHCPServerIPPoolTableEndIPAddress | 1.3.6.1.4.1.1751.2.4.15.2.1.3 | ||
| This variable represents the end IP address for this DHCP IP Address IP Pool Table entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriDHCPServerIPPoolTableWidth | 1.3.6.1.4.1.1751.2.4.15.2.1.4 | ||
| This variable represents the width or number of IP Address in the DHCP IP Address Pool table entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriDHCPServerIPPoolTableComment | 1.3.6.1.4.1.1751.2.4.15.2.1.5 | ||
| The variable represents the comment for this entry. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriDHCPServerIPPoolTableEntryStatus | 1.3.6.1.4.1.1751.2.4.15.2.1.6 | ||
| The variable indicates the status of the DHCP IP Address Pool Table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2), delete(3) | ||
| oriDHCPServerDefaultGatewayIPAddress | 1.3.6.1.4.1.1751.2.4.15.3 | ||
| This parameter represents the IP Address of the gateway or router that the DHCP Server will assign to the DHCP client. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriDHCPServerDefaultLeaseTime | 1.3.6.1.4.1.1751.2.4.15.4 | ||
| This parameter represents the default lease time in seconds for the IP address assigned by the DHCP server to the DHCP client. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriDHCPServerMaximumLeaseTime | 1.3.6.1.4.1.1751.2.4.15.5 | ||
| This parameter represents the maximum lease time in seconds for the IP address assigned by the DHCP server to the DHCP client. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriDHCPServerDNSIPAddress | 1.3.6.1.4.1.1751.2.4.15.6 | ||
| This variable object represents the DNS IP Address handed to DHCP clients. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriDHCPServerNumIPPoolTableEntry | 1.3.6.1.4.1.1751.2.4.15.7 | ||
| This variable represents the number of entries in the DHCP IP Address Pool Table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| orinocoHTTP | 1.3.6.1.4.1.1751.2.4.16 | ||
| OBJECT IDENTIFIER | |||
| oriHTTPStatus | 1.3.6.1.4.1.1751.2.4.16.1 | ||
| This parameter represents the Web status. If this parameter is enabled, then the device can be managed via a standard web browser otherwise not. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriHTTPPassword | 1.3.6.1.4.1.1751.2.4.16.2 | ||
| This parameter represents the login password in order to manage the device via a standard web browser. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriHTTPPort | 1.3.6.1.4.1.1751.2.4.16.3 | ||
| This parameter represents the TCP/IP port by which the HTTP daemon will be accessible. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriHTTPHelpInformationLink | 1.3.6.1.4.1.1751.2.4.16.4 | ||
| This parameter is used in order to set the link in the web interface for where help information can be retrieved. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| orinocoWDS | 1.3.6.1.4.1.1751.2.4.17 | ||
| OBJECT IDENTIFIER | |||
| oriWDSSetupTable | 1.3.6.1.4.1.1751.2.4.17.1 | ||
| This table is used in order to configurate the WDS objects in the Access Point. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriWDSSetupTableEntry | |||
| oriWDSSetupTableEntry | 1.3.6.1.4.1.1751.2.4.17.1.1 | ||
| The entry is the WDS table. | |||
| OBJECT-TYPE | |||
| OriWDSSetupTableEntry | |||
| oriWDSSetupTablePortIndex | 1.3.6.1.4.1.1751.2.4.17.1.1.1 | ||
| The port number of the port for which this entry contains bridge management information. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..6 | ||
| oriWDSSetupTableEntryStatus | 1.3.6.1.4.1.1751.2.4.17.1.1.2 | ||
| Flag indicating whether Point to Point is enabled. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriWDSSetupTablePartnerMACAddress | 1.3.6.1.4.1.1751.2.4.17.1.1.3 | ||
| The MAC address of the partner to this interface. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| orinocoTrap | 1.3.6.1.4.1.1751.2.4.18 | ||
| OBJECT IDENTIFIER | |||
| oriTrapVariable | 1.3.6.1.4.1.1751.2.4.18.1 | ||
| OBJECT IDENTIFIER | |||
| oriGenericTrapVariable | 1.3.6.1.4.1.1751.2.4.18.1.1 | ||
| This object is used to provide additional information on traps. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriTrapVarMACAddress | 1.3.6.1.4.1.1751.2.4.18.1.2 | ||
| This object is used to store the MAC address of the ORiNOCO device that has sent a trap. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| oriTrapVarTFTPIPAddress | 1.3.6.1.4.1.1751.2.4.18.1.3 | ||
| This object is used to store the IP Address of the TFTP server. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriTrapVarTFTPFilename | 1.3.6.1.4.1.1751.2.4.18.1.4 | ||
| This object is used to store the name of the file on which the TFTP operation has occurred. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriTrapVarTFTPOperation | 1.3.6.1.4.1.1751.2.4.18.1.5 | ||
| This object is used to store the TFTP operation that failed, either download or upload | |||
| OBJECT-TYPE | |||
| INTEGER | upload(1), download(2) | ||
| oriTrapVarUnauthorizedManagerIPaddress | 1.3.6.1.4.1.1751.2.4.18.1.6 | ||
| This variable is used to store the IP address of the unauthorized manager that has attempted to manage the device. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriTrapVarUnAuthorizedManagerCount | 1.3.6.1.4.1.1751.2.4.18.1.8 | ||
| This parameter represents a counter for the number of unauthorized SNMP managers that have attempted to modify and/or view the devices setup. When this number is incremented a trap should be sent out notifying the trap host(s) that an unauthorized station has attempted to configure or monitor the device the count should also be sent out in the trap message. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriTrapVarTaskSuspended | 1.3.6.1.4.1.1751.2.4.18.1.9 | ||
| This trap variable is used to inform what task has been suspended on the ORiNOCO device. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriConfigurationTrapsStatus | 1.3.6.1.4.1.1751.2.4.18.1.10 | ||
| This object is used to enable or disable the ORiNOCO Configuration related traps. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriSecurityTrapsStatus | 1.3.6.1.4.1.1751.2.4.18.1.11 | ||
| This object is used to enable or disable the ORiNOCO Security related traps. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriWirelessIfTrapsStatus | 1.3.6.1.4.1.1751.2.4.18.1.12 | ||
| This object is used to enable or disable the ORiNOCO Wireless Interface related traps. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriOperationalTrapsStatus | 1.3.6.1.4.1.1751.2.4.18.1.13 | ||
| This object is used to enable or disable the ORiNOCO Operational related traps. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriFlashMemoryTrapsStatus | 1.3.6.1.4.1.1751.2.4.18.1.14 | ||
| This object is used to enable or disable the ORiNOCO Flash Card and Memory related traps. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriTFTPTrapsStatus | 1.3.6.1.4.1.1751.2.4.18.1.15 | ||
| This object is used to enable or disable the ORiNOCO TFTP related traps. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriTrapsImage | 1.3.6.1.4.1.1751.2.4.18.1.16 | ||
| This object is used to enable or disable the ORiNOCO Image related traps. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriTrapVarUnauthorizedClientMACAddress | 1.3.6.1.4.1.1751.2.4.18.1.17 | ||
| This trap variable is used to store the MAC Address of an unauthorized client station. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| oriTrapVarWirelessCard | 1.3.6.1.4.1.1751.2.4.18.1.18 | ||
| This trap variable is used to determine on which Wireless Card, PC Card A or PC Card B, a wireless TRAP has occured on. | |||
| OBJECT-TYPE | |||
| INTEGER | pcCardA(1), pcCardB(2) | ||
| oriConfigurationTraps | 1.3.6.1.4.1.1751.2.4.18.2 | ||
| This the configuration related traps for ORiNOCO devices | |||
| OBJECT-IDENTITY | |||
| oriTrapIPAddrAssignmentNotConfigured | 1.3.6.1.4.1.1751.2.4.18.2.1 | ||
| This trap is to identify the that the IP Address Pool Assignment Type has not been configured in the ORiNOCO device. ORiNOCO Devices that use this Trap: - Access Server 2000 | |||
| NOTIFICATION-TYPE | |||
| oriGenericTrapVariable | |||
| oriTrapVarMACAddress | |||
| oriTrapRADIUSNotConfigured | 1.3.6.1.4.1.1751.2.4.18.2.2 | ||
| This trap is to inform that the RADIUS configuration parameters have not been configured in the ORiNOCO device. ORiNOCO Devices that use this Trap: - Access Server 2000 | |||
| NOTIFICATION-TYPE | |||
| oriGenericTrapVariable | |||
| oriTrapVarMACAddress | |||
| oriTrapDNSIPNotConfigured | 1.3.6.1.4.1.1751.2.4.18.2.3 | ||
| This traps is used to inform that the DNS IP Address has not been configured in the ORiNOCO device. ORiNOCO Devices that use this Trap: - Access Server 2000 | |||
| NOTIFICATION-TYPE | |||
| oriGenericTrapVariable | |||
| oriTrapVarMACAddress | |||
| oriTrapWINSIPNotConfigured | 1.3.6.1.4.1.1751.2.4.18.2.4 | ||
| This traps is used to inform that the WINS or NBNS IP Address has not been configured in the ORiNOCO device. ORiNOCO Devices that use this Trap: - Access Server 2000 | |||
| NOTIFICATION-TYPE | |||
| oriGenericTrapVariable | |||
| oriTrapVarMACAddress | |||
| oriTrapRADIUSAuthenticationNotConfigured | 1.3.6.1.4.1.1751.2.4.18.2.5 | ||
| This trap is sent when the radius authentication information is not configured in the ORiNOCO device. ORiNOCO Devices that use this Trap: - Access Server 2000 | |||
| NOTIFICATION-TYPE | |||
| oriGenericTrapVariable | |||
| oriTrapVarMACAddress | |||
| oriTrapRADIUSAccountingNotConfigured | 1.3.6.1.4.1.1751.2.4.18.2.6 | ||
| This trap is sent when the radius accounting information is not configured in the ORiNOCO device. ORiNOCO Devices that use this Trap: - Access Server 2000 | |||
| NOTIFICATION-TYPE | |||
| oriGenericTrapVariable | |||
| oriTrapVarMACAddress | |||
| oriTrapDuplicateIPAddressEncountered | 1.3.6.1.4.1.1751.2.4.18.2.7 | ||
| This trap is generated when the access point device has encountered another network device with he same IP Address. ORiNOCO Devices that use this Trap: - Access Server 2000 | |||
| NOTIFICATION-TYPE | |||
| oriGenericTrapVariable | |||
| oriTrapVarMACAddress | |||
| oriSecurityTraps | 1.3.6.1.4.1.1751.2.4.18.3 | ||
| This is the security related traps for ORiNOCO Devices. | |||
| OBJECT-IDENTITY | |||
| oriTrapInvalidEncryptionKey | 1.3.6.1.4.1.1751.2.4.18.3.1 | ||
| This trap is to identify that an invalid encryption key has been detected by the ORiNOCO device. ORiNOCO Devices that use this Trap: - Access Server 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarUnauthorizedClientMACAddress | |||
| oriTrapAuthenticationFailure | 1.3.6.1.4.1.1751.2.4.18.3.2 | ||
| This trap is to inform that a client RADIUS authentication failure has occurred at the ORiNOCO device. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarUnauthorizedClientMACAddress | |||
| oriTrapUnauthorizedManagerDetected | 1.3.6.1.4.1.1751.2.4.18.3.3 | ||
| This trap is to inform that an unauthorized SNMP manager has attempted to view and/or modify parameters. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarUnauthorizedManagerIPaddress | |||
| oriTrapVarUnAuthorizedManagerCount | |||
| oriWirelessIfTraps | 1.3.6.1.4.1.1751.2.4.18.4 | ||
| This is the wireless interface or wireless card related traps for ORiNOCO devices. | |||
| OBJECT-IDENTITY | |||
| oriTrapWLCNotPresent | 1.3.6.1.4.1.1751.2.4.18.4.1 | ||
| This trap is to inform that a Wirless Card (WLC) is not present in the ORiNOCO device. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarWirelessCard | |||
| oriTrapWLCFailure | 1.3.6.1.4.1.1751.2.4.18.4.2 | ||
| This trap is to identify that there was some type of failure in the wireless interface card. This trap can signify that the there is a failure with the ORiNOCO PC Card. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarWirelessCard | |||
| oriTrapWLCRemoval | 1.3.6.1.4.1.1751.2.4.18.4.3 | ||
| This trap is to inform that the wireless interface card (ORiNOCO PC Card) has been removed from the ORiNOCO device. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarWirelessCard | |||
| oriTrapWLCIncompatibleFirmware | 1.3.6.1.4.1.1751.2.4.18.4.4 | ||
| This trap is sent to inform that the firmware in the wireless interface card in the access point device is incompatible. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarWirelessCard | |||
| oriTrapWLCVoltageDiscrepancy | 1.3.6.1.4.1.1751.2.4.18.4.5 | ||
| This trap is sent when non 5 volt card or 3.3 volt card is inserted in the access point device. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarWirelessCard | |||
| oriTrapWLCIncompatibleVendor | 1.3.6.1.4.1.1751.2.4.18.4.6 | ||
| This trap is generated when an incompatible wireless vendor card is inserted or present in the access point device. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarWirelessCard | |||
| oriTrapWLCFirmwareDownloadFailure | 1.3.6.1.4.1.1751.2.4.18.4.7 | ||
| This trap is generated when a failure occurs during the firmware download process. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Poing 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarWirelessCard | |||
| oriTrapWLCFirmwareFailure | 1.3.6.1.4.1.1751.2.4.18.4.8 | ||
| This trap is generated when a failure occurs in the Wireless Card Firmware. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Poing 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarWirelessCard | |||
| oriGenericTrapVariable | |||
| oriOperationalTraps | 1.3.6.1.4.1.1751.2.4.18.5 | ||
| This is the operational related traps for ORiNOCO devices. | |||
| OBJECT-IDENTITY | |||
| oriTrapWatchDogTimerExpired | 1.3.6.1.4.1.1751.2.4.18.5.1 | ||
| This trap is sent when the software watch dog timer has expired. This can signify that some problem has occurred with one or more software modules and the system will reboot itself. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriGenericTrapVariable | |||
| oriTrapVarMACAddress | |||
| oriTrapVarTaskSuspended | |||
| oriTrapRADIUSServerNotResponding | 1.3.6.1.4.1.1751.2.4.18.5.2 | ||
| This trap is to indicate that no RADIUS server(s) are responding to authentication requests sent by the RADIUS client within the ORiNOCO device. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriGenericTrapVariable | |||
| oriTrapModuleNotInitialized | 1.3.6.1.4.1.1751.2.4.18.5.3 | ||
| This trap is to inform that a certain software or hardware module has not been initialized or failed to be initialized. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriGenericTrapVariable | |||
| oriTrapChangeInAdminState | 1.3.6.1.4.1.1751.2.4.18.5.4 | ||
| This trap is sent when the administration state of the ORiNOCO device is changes either from Normal to maintenance mode or vice-versa. ORiNOCO Devices that use this Trap: - Access Server 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarMACAddress | |||
| oriTrapDeviceRebooting | 1.3.6.1.4.1.1751.2.4.18.5.5 | ||
| This trap is sent when the ORiNOCO device has received a request to be rebooted. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarMACAddress | |||
| oriTrapTaskSuspended | 1.3.6.1.4.1.1751.2.4.18.5.6 | ||
| This trap is sent when a task in the ORiNOCO device has suspended. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarTaskSuspended | |||
| oriTrapBootPFailed | 1.3.6.1.4.1.1751.2.4.18.5.7 | ||
| This trap is generated when a response to the BootP request is not received, hence the access point device is not dynamically assigned an IP Address. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarMACAddress | |||
| oriTrapDHCPFailed | 1.3.6.1.4.1.1751.2.4.18.5.8 | ||
| This trap is generated when a response to the DHCP client request is not received, hence the access point device is not dynamically assigned an IP Address. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarMACAddress | |||
| oriFlashTraps | 1.3.6.1.4.1.1751.2.4.18.6 | ||
| This is the flash memory related traps for ORiNOCO devices. | |||
| OBJECT-IDENTITY | |||
| oriTrapFlashMemoryEmpty | 1.3.6.1.4.1.1751.2.4.18.6.1 | ||
| This trap is used to inform that there is no data present in flash memory - either on the Flash card or the onboard flash memory. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapFlashMemoryCorrupted | 1.3.6.1.4.1.1751.2.4.18.6.2 | ||
| This trap is to inform that the data content of flash memory is corrupted. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTFTPTraps | 1.3.6.1.4.1.1751.2.4.18.7 | ||
| This is the TFTP related traps for ORiNOCO devices. | |||
| OBJECT-IDENTITY | |||
| oriTrapTFTPFailedOperation | 1.3.6.1.4.1.1751.2.4.18.7.1 | ||
| This trap is used to notify that a failure occurred with the TFTP operation. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarTFTPIPAddress | |||
| oriTrapVarTFTPFilename | |||
| oriTrapVarTFTPOperation | |||
| oriTrapTFTPOperationInitiated | 1.3.6.1.4.1.1751.2.4.18.7.2 | ||
| This trap is used to notify that a TFTP operation has been initiated. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarTFTPIPAddress | |||
| oriTrapVarTFTPFilename | |||
| oriTrapVarTFTPOperation | |||
| oriTrapTFTPOperationCompleted | 1.3.6.1.4.1.1751.2.4.18.7.3 | ||
| This trap is used to notify that a TFTP operation has been completed. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapVarTFTPIPAddress | |||
| oriTrapVarTFTPFilename | |||
| oriTrapVarTFTPOperation | |||
| oriMiscTraps | 1.3.6.1.4.1.1751.2.4.18.8 | ||
| This is a miscellaneous trap group for the ORiNOCO devices. | |||
| OBJECT-IDENTITY | |||
| oriImageTraps | 1.3.6.1.4.1.1751.2.4.18.9 | ||
| This is image related traps for the ORiNOCO devices. | |||
| OBJECT-IDENTITY | |||
| oriTrapZeroSizeImage | 1.3.6.1.4.1.1751.2.4.18.9.1 | ||
| This trap is generated when an a zero size image is loaded to the ORiNOCO device. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapInvalidImage | 1.3.6.1.4.1.1751.2.4.18.9.2 | ||
| This trap is sent when an invalid image is loaded to the ORiNOCO device. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapImageTooLarge | 1.3.6.1.4.1.1751.2.4.18.9.3 | ||
| This trap is sent when the image loaded to the access point device exceeds the size limitation of flash. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| oriTrapIncompatibleImage | 1.3.6.1.4.1.1751.2.4.18.9.4 | ||
| This trap is sent when an incompatible image is loaded to the ORiNOCO device. ORiNOCO Devices that use this Trap: - Access Server 2000 - Access Point 2000 | |||
| NOTIFICATION-TYPE | |||
| orinocoIPARP | 1.3.6.1.4.1.1751.2.4.19 | ||
| OBJECT IDENTIFIER | |||
| oriProxyARPStatus | 1.3.6.1.4.1.1751.2.4.19.1 | ||
| This object is used to enable/disable the Proxy ARP functionality in the ORiNOCO Device. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriIPARPFilteringStatus | 1.3.6.1.4.1.1751.2.4.19.2 | ||
| This object is used to enable/disable the IP/ARP functionality in the ORiNOCO Device. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriIPARPFilteringIPAddress | 1.3.6.1.4.1.1751.2.4.19.3 | ||
| This object is used to specify the IP/ARP Filtering address in the ORiNOCO Device. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriIPARPFilteringSubnetMask | 1.3.6.1.4.1.1751.2.4.19.4 | ||
| This object is used to specify the IP/ARP Subnet Mask in the ORiNOCO Device. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| orinocoSpanningTree | 1.3.6.1.4.1.1751.2.4.20 | ||
| OBJECT IDENTIFIER | |||
| oriSpanningTreeStatus | 1.3.6.1.4.1.1751.2.4.20.1 | ||
| This object is used to enable/disable the spanning tree protocol in the ORiNOCO Device. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| orinocoSecurity | 1.3.6.1.4.1.1751.2.4.21 | ||
| OBJECT IDENTIFIER | |||
| oriSecurityConfiguration | 1.3.6.1.4.1.1751.2.4.21.1 | ||
| This object represents the supported security configuration options. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), wep(2), dot1x(3), mixedWepAnddot1x(4) | ||
| oriSecurityEncryptionKeyLengthTable | 1.3.6.1.4.1.1751.2.4.21.2 | ||
| This table is used to specify the encryption key length per wireless interface. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriSecurityEncryptionKeyLengthTableEntry | |||
| oriSecurityEncryptionKeyLengthTableEntry | 1.3.6.1.4.1.1751.2.4.21.2.1 | ||
| This is an entry in the encryption key length table. | |||
| OBJECT-TYPE | |||
| OriSecurityEncryptionKeyLengthTableEntry | |||
| oriSecurityEncryptionKeyLength | 1.3.6.1.4.1.1751.2.4.21.2.1.1 | ||
| This object represents the encryption key length. | |||
| OBJECT-TYPE | |||
| INTEGER | fortyBits(1), oneHundredTwentyEightBits(2) | ||
| orinocoHereUare | 1.3.6.1.4.1.1751.2.4.22 | ||
| OBJECT IDENTIFIER | |||
| oriHereUareECBStatus | 1.3.6.1.4.1.1751.2.4.22.1 | ||
| This object is used to enable or disable the HereUare feature. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriHereUareECBBootStrapIPAddress | 1.3.6.1.4.1.1751.2.4.22.2 | ||
| This object represents the BootStrap IP Address for the HereUare ECB Server. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriHereUareECBSecurityStatus | 1.3.6.1.4.1.1751.2.4.22.3 | ||
| This object is used to enable or disable the ECB security in the HereUare feature. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriHereUareECBSecurityKey | 1.3.6.1.4.1.1751.2.4.22.4 | ||
| This object represents the ECB security key for the HereUAre feature. This object should be masked by the SNMP agent. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| oriHereUareECBNATProxyStatus | 1.3.6.1.4.1.1751.2.4.22.5 | ||
| This object is used to enable or disable the NAT proxy function in the HereUAre feature. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| oriHereUareECBNATProxyIPAddress | 1.3.6.1.4.1.1751.2.4.22.6 | ||
| This object represents the IP Address of the ECB NAT Proxy Server. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriHereUareECBClientTable | 1.3.6.1.4.1.1751.2.4.22.7 | ||
| This table is to monitor the clients that are using HereUare and don not require further authentication. This table is limited to 500 entries. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| OriHereUareECBClientTableEntry | |||
| oriHereUareECBClientTableEntry | 1.3.6.1.4.1.1751.2.4.22.7.1 | ||
| This is an entry in the HereUare ECB table. | |||
| OBJECT-TYPE | |||
| OriHereUareECBClientTableEntry | |||
| oriHereUareECBClientTableIndex | 1.3.6.1.4.1.1751.2.4.22.7.1.1 | ||
| This is the index for the HereUare ECB Client table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| oriHereUareECBClientTableStationName | 1.3.6.1.4.1.1751.2.4.22.7.1.2 | ||
| This object represents the HereUare ECB Client Station Name. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| oriHereUareECBClientTableMACAddress | 1.3.6.1.4.1.1751.2.4.22.7.1.3 | ||
| This object represents the HereUare ECB Client Station MAC Address. | |||
| OBJECT-TYPE | |||
| PhysAddress | |||
| oriHereUareECBClientTableIPAddress | 1.3.6.1.4.1.1751.2.4.22.7.1.4 | ||
| This object represents the HereUare ECB Client Station IP Address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| oriHereUareECBClientTableLinkStatus | 1.3.6.1.4.1.1751.2.4.22.7.1.5 | ||
| This object represents the HereUare ECB Client Station Link Status. | |||
| OBJECT-TYPE | |||
| INTEGER | ecbWLStationUnauthorized(1), ecbWLStationAuthorized(2), ecbWLSendingKeepAlive(3), ecbWLAwaitingKeepAlive(4), ecbWLECBDConnected(5), ecbWLECBDDisconnected(6), ecbWLECBDSendingKeepAlive(7), ecbWLMemberConnected(8), ecbWLMemberDisconnected(9), ecbWLBootStrapConnected(10), ecbWLBootStrapDisconnected(11), ecbWLTCConnected(12), ecbWLTCDisconnected(13) | ||
| oriHereUareECBClientTablePingCountDown | 1.3.6.1.4.1.1751.2.4.22.7.1.6 | ||
| This object represents the number of seconds until the ECB makes its next keep-alive ping to this station. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| oriHereUareECBClientTableConnectionTime | 1.3.6.1.4.1.1751.2.4.22.7.1.7 | ||
| This object represents the HereUare ECB Client station connection time. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| orinocoSpectraLink | 1.3.6.1.4.1.1751.2.4.23 | ||
| OBJECT IDENTIFIER | |||
| oriSpectraLinkStatus | 1.3.6.1.4.1.1751.2.4.23.1 | ||
| This object is used to enable or disable the SpectraLink VoIP feature. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| OriSystemInvMgmtComponentTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriSystemInvMgmtTableComponentIndex | |||
| DisplayString as oriSystemInvMgmtTableComponentSerialNumber | |||
| DisplayString as oriSystemInvMgmtTableComponentName | |||
| Integer32 as oriSystemInvMgmtTableComponentId | |||
| Integer32 as oriSystemInvMgmtTableComponentVariant | |||
| Integer32 as oriSystemInvMgmtTableComponentMajorVersion | |||
| Integer32 as oriSystemInvMgmtTableComponentMinorVersion | |||
| OriSystemInvMgmtTableComponentIfTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriSystemInvMgmtInterfaceTableIndex | |||
| Integer32 as oriSystemInvMgmtInterfaceId | |||
| INTEGER as oriSystemInvMgmtInterfaceRole | |||
| Integer32 as oriSystemInvMgmtInterfaceVariant | |||
| Integer32 as oriSystemInvMgmtInterfaceBottomNumber | |||
| Integer32 as oriSystemInvMgmtInterfaceTopNumber | |||
| OriWirelessIfPropertiesEntry | |||
| SEQUENCE | |||
| Integer32 as oriWirelessIfPropertiesIndex | |||
| DisplayString as oriWirelessIfNetworkName | |||
| Integer32 as oriWirelessIfMediumReservation | |||
| INTEGER as oriWirelessIfInterferenceRobustness | |||
| Integer32 as oriWirelessIfDTIMPeriod | |||
| Integer32 as oriWirelessIfChannel | |||
| INTEGER as oriWirelessIfDistancebetweenAPs | |||
| INTEGER as oriWirelessIfMulticastRate | |||
| INTEGER as oriWirelessIfClosedSystem | |||
| OCTET STRING as oriWirelessIfAllowedSupportedDataRates | |||
| OCTET STRING as oriWirelessIfRegulatoryDomainList | |||
| OCTET STRING as oriWirelessIfAllowedChannels | |||
| PhysAddress as oriWirelessIfMACAddress | |||
| INTEGER as oriWirelessIfLoadBalancing | |||
| INTEGER as oriWirelessIfMediumDensityDistribution | |||
| OriWirelessIfSecurityEntry | |||
| SEQUENCE | |||
| Integer32 as oriWirelessIfSecurityIndex | |||
| INTEGER as oriWirelessIfEncryptionOptions | |||
| INTEGER as oriWirelessIfEncryptionStatus | |||
| DisplayString as oriWirelessIfEncryptionKey1 | |||
| DisplayString as oriWirelessIfEncryptionKey2 | |||
| DisplayString as oriWirelessIfEncryptionKey3 | |||
| DisplayString as oriWirelessIfEncryptionKey4 | |||
| INTEGER as oriWirelessIfEncryptionTxKey | |||
| INTEGER as oriWirelessIfDenyNonEncryptedData | |||
| Integer32 as oriWirelessIfProfileCode | |||
| OriNetworkIPXClientEntry | |||
| SEQUENCE | |||
| Integer32 as oriNetworkIPXPPPSessionId | |||
| OCTET STRING as oriNetworkIPXClientNetworkNumber | |||
| PhysAddress as oriNetworkIPXClientMAC | |||
| INTEGER as oriNetworkIPXClientStatus | |||
| OriSNMPAccessTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriSNMPAccessTableIndex | |||
| IpAddress as oriSNMPAccessTableIPAddress | |||
| IpAddress as oriSNMPAccessTableIPMask | |||
| INTEGER as oriSNMPAccessTableInterface | |||
| DisplayString as oriSNMPAccessTableComment | |||
| INTEGER as oriSNMPAccessTableEntryStatus | |||
| OriSNMPTrapHostTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriSNMPTrapHostTableIndex | |||
| IpAddress as oriSNMPTrapHostTableIPAddress | |||
| DisplayString as oriSNMPTrapHostTablePassword | |||
| DisplayString as oriSNMPTrapHostTableComment | |||
| INTEGER as oriSNMPTrapHostTableEntryStatus | |||
| OriProtocolFilterTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriProtocolFilterTableIndex | |||
| OCTET STRING as oriProtocolFilterProtocol | |||
| DisplayString as oriProtocolFilterProtocolComment | |||
| INTEGER as oriProtocolFilterStatus | |||
| OriAccessControlEntry | |||
| SEQUENCE | |||
| Integer32 as oriAccessControlTableIndex | |||
| PhysAddress as oriAccessControlTableMACAddress | |||
| DisplayString as oriAccessControlTableComment | |||
| INTEGER as oriAccessControlTableEntryStatus | |||
| OriStaticMACAddressFilterEntry | |||
| SEQUENCE | |||
| Integer32 as oriStaticMACAddressFilterTableIndex | |||
| PhysAddress as oriStaticMACAddressFilterWiredAddress | |||
| PhysAddress as oriStaticMACAddressFilterWiredMask | |||
| PhysAddress as oriStaticMACAddressFilterWirelessAddress | |||
| PhysAddress as oriStaticMACAddressFilterWirelessMask | |||
| INTEGER as oriStaticMACAddressFilterStatus | |||
| DisplayString as oriStaticMACAddressFilterComment | |||
| OriStormThresholdTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriStormThresholdIfBroadcast | |||
| Integer32 as oriStormThresholdIfMulticast | |||
| OriBroadcastFilteringTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriBroadcastFilteringTableIndex | |||
| DisplayString as oriBroadcastFilteringProtocolName | |||
| INTEGER as oriBroadcastFilteringDirection | |||
| INTEGER as oriBroadcastFilteringStatus | |||
| OriRADIUSAuthServerTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriRADIUSAuthServerTableIndex | |||
| INTEGER as oriRADIUSAuthServerType | |||
| INTEGER as oriRADIUSAuthServerStatus | |||
| IpAddress as oriRADIUSAuthServerIPAddress | |||
| Integer32 as oriRADIUSAuthServerDestPort | |||
| DisplayString as oriRADIUSAuthServerSharedSecret | |||
| Integer32 as oriRADIUSAuthServerResponseTime | |||
| Integer32 as oriRADIUSAuthServerMaximumRetransmission | |||
| Counter32 as oriRADIUSAuthClientAccessRequests | |||
| Counter32 as oriRADIUSAuthClientAccessRetransmissions | |||
| Counter32 as oriRADIUSAuthClientAccessAccepts | |||
| Counter32 as oriRADIUSAuthClientAccessChallenges | |||
| Counter32 as oriRADIUSAuthClientAccessRejects | |||
| Counter32 as oriRADIUSAuthClientMalformedAccessResponses | |||
| Counter32 as oriRADIUSAuthClientAuthInvalidAuthenticators | |||
| Counter32 as oriRADIUSAuthClientTimeouts | |||
| OriRADIUSAcctServerTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriRADIUSAcctServerTableIndex | |||
| INTEGER as oriRADIUSAcctServerType | |||
| INTEGER as oriRADIUSAcctServerStatus | |||
| IpAddress as oriRADIUSAcctServerIPAddress | |||
| Integer32 as oriRADIUSAcctServerDestPort | |||
| DisplayString as oriRADIUSAcctServerSharedSecret | |||
| Integer32 as oriRADIUSAcctServerResponseTime | |||
| Integer32 as oriRADIUSAcctServerMaximumRetransmission | |||
| Counter32 as oriRADIUSAcctClientAccountingRequests | |||
| Counter32 as oriRADIUSAcctClientAccountingRetransmissions | |||
| Counter32 as oriRADIUSAcctClientAccountingResponses | |||
| Counter32 as oriRADIUSAcctClientAcctInvalidAuthenticators | |||
| OriIAPPMACIPTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriIAPPMACIPTableIndex | |||
| DisplayString as oriIAPPMACIPTableSystemName | |||
| IpAddress as oriIAPPMACIPTableIPAddress | |||
| PhysAddress as oriIAPPMACIPTableBSSID | |||
| DisplayString as oriIAPPMACIPTableESSID | |||
| OriLinkTestTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriLinkTestTableIndex | |||
| INTEGER as oriLinkTestInProgress | |||
| DisplayString as oriLinkTestStationName | |||
| PhysAddress as oriLinkTestMACAddress | |||
| Integer32 as oriLinkTestStationProfile | |||
| Integer32 as oriLinkTestOurCurSignalLevel | |||
| Integer32 as oriLinkTestOurCurNoiseLevel | |||
| Integer32 as oriLinkTestOurCurSNR | |||
| Integer32 as oriLinkTestOurMinSignalLevel | |||
| Integer32 as oriLinkTestOurMinNoiseLevel | |||
| Integer32 as oriLinkTestOurMinSNR | |||
| Integer32 as oriLinkTestOurMaxSignalLevel | |||
| Integer32 as oriLinkTestOurMaxNoiseLevel | |||
| Integer32 as oriLinkTestOurMaxSNR | |||
| Integer32 as oriLinkTestOurLowFrameCount | |||
| Integer32 as oriLinkTestOurStandardFrameCount | |||
| Integer32 as oriLinkTestOurMediumFrameCount | |||
| Integer32 as oriLinkTestOurHighFrameCount | |||
| Integer32 as oriLinkTestHisCurSignalLevel | |||
| Integer32 as oriLinkTestHisCurNoiseLevel | |||
| Integer32 as oriLinkTestHisCurSNR | |||
| Integer32 as oriLinkTestHisMinSignalLevel | |||
| Integer32 as oriLinkTestHisMinNoiseLevel | |||
| Integer32 as oriLinkTestHisMinSNR | |||
| Integer32 as oriLinkTestHisMaxSignalLevel | |||
| Integer32 as oriLinkTestHisMaxNoiseLevel | |||
| Integer32 as oriLinkTestHisMaxSNR | |||
| Integer32 as oriLinkTestHisLowFrameCount | |||
| Integer32 as oriLinkTestHisStandardFrameCount | |||
| Integer32 as oriLinkTestHisMediumFrameCount | |||
| Integer32 as oriLinkTestHisHighFrameCount | |||
| DisplayString as oriLinkTestInterface | |||
| DisplayString as oriLinkTestRadioType | |||
| OriLinkIntTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriLinkIntTableIndex | |||
| IpAddress as oriLinkIntTableTargetIPAddress | |||
| DisplayString as oriLinkIntTableComment | |||
| INTEGER as oriLinkIntTableEntryStatus | |||
| OriPPPMACtoIPMappingTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriPPPMACtoIPTableIndex | |||
| PhysAddress as oriPPPMACtoIPTableMACAddress | |||
| IpAddress as oriPPPMACtoIPTableIPAddress | |||
| DisplayString as oriPPPMACtoIPTableComment | |||
| INTEGER as oriPPPMACtoIPTableEntryStatus | |||
| OriPPPIPPoolTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriPPPIPPoolTableIndex | |||
| IpAddress as oriPPPIPPoolTableStartIPAddress | |||
| IpAddress as oriPPPIPPoolTableEndIPAddress | |||
| Integer32 as oriPPPIPPoolTableWidth | |||
| DisplayString as oriPPPIPPoolTableComment | |||
| INTEGER as oriPPPIPPoolTableEntryStatus | |||
| OriDHCPServerIPPoolTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriDHCPServerIPPoolTableIndex | |||
| IpAddress as oriDHCPServerIPPoolTableStartIPAddress | |||
| IpAddress as oriDHCPServerIPPoolTableEndIPAddress | |||
| Integer32 as oriDHCPServerIPPoolTableWidth | |||
| DisplayString as oriDHCPServerIPPoolTableComment | |||
| INTEGER as oriDHCPServerIPPoolTableEntryStatus | |||
| OriWDSSetupTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriWDSSetupTablePortIndex | |||
| INTEGER as oriWDSSetupTableEntryStatus | |||
| PhysAddress as oriWDSSetupTablePartnerMACAddress | |||
| OriSecurityEncryptionKeyLengthTableEntry | |||
| SEQUENCE | |||
| INTEGER as oriSecurityEncryptionKeyLength | |||
| OriHereUareECBClientTableEntry | |||
| SEQUENCE | |||
| Integer32 as oriHereUareECBClientTableIndex | |||
| DisplayString as oriHereUareECBClientTableStationName | |||
| PhysAddress as oriHereUareECBClientTableMACAddress | |||
| IpAddress as oriHereUareECBClientTableIPAddress | |||
| INTEGER as oriHereUareECBClientTableLinkStatus | |||
| Counter32 as oriHereUareECBClientTablePingCountDown | |||
| Counter32 as oriHereUareECBClientTableConnectionTime | |||