OSPF-MIB

File: OSPF-MIB.mib (89120 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
RFC1213-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Gauge32 Integer32 IpAddress
TEXTUAL-CONVENTION TruthValue RowStatus
MODULE-COMPLIANCE OBJECT-GROUP mib-2

Defined Objects

ospf 1.3.6.1.2.1.14
The MIB module to describe the OSPF Version 2 Protocol
MODULE-IDENTITY    

ospfGeneralGroup 1.3.6.1.2.1.14.1
OBJECT IDENTIFIER    

ospfRouterId 1.3.6.1.2.1.14.1.1
A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
OBJECT-TYPE    
  RouterID  

ospfAdminStat 1.3.6.1.2.1.14.1.2
The administrative status of OSPF in the router. The value 'enabled' denotes that the OSPF Process is active on at least one inter- face; 'disabled' disables it on all inter- faces.
OBJECT-TYPE    
  Status  

ospfVersionNumber 1.3.6.1.2.1.14.1.3
The current version number of the OSPF proto- col is 2.
OBJECT-TYPE    
  INTEGER version2(2)  

ospfAreaBdrRtrStatus 1.3.6.1.2.1.14.1.4
A flag to note whether this router is an area border router.
OBJECT-TYPE    
  TruthValue  

ospfASBdrRtrStatus 1.3.6.1.2.1.14.1.5
A flag to note whether this router is config- ured as an Autonomous System border router.
OBJECT-TYPE    
  TruthValue  

ospfExternLsaCount 1.3.6.1.2.1.14.1.6
The number of external (LS type 5) link-state advertisements in the link-state database.
OBJECT-TYPE    
  Gauge32  

ospfExternLsaCksumSum 1.3.6.1.2.1.14.1.7
The 32-bit unsigned sum of the LS checksums of the external link-state advertisements con- tained in the link-state database. This sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers.
OBJECT-TYPE    
  Integer32  

ospfTOSSupport 1.3.6.1.2.1.14.1.8
The router's support for type-of-service rout- ing.
OBJECT-TYPE    
  TruthValue  

ospfOriginateNewLsas 1.3.6.1.2.1.14.1.9
The number of new link-state advertisements that have been originated. This number is in- cremented each time the router originates a new LSA.
OBJECT-TYPE    
  Counter32  

ospfRxNewLsas 1.3.6.1.2.1.14.1.10
The number of link-state advertisements re- ceived determined to be new instantiations. This number does not include newer instantia- tions of self-originated link-state advertise- ments.
OBJECT-TYPE    
  Counter32  

ospfExtLsdbLimit 1.3.6.1.2.1.14.1.11
The maximum number of non-default AS- external-LSAs entries that can be stored in the link-state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches ospfExtLsdbLimit, the router enters Overflow- State. The router never holds more than ospfExtLsdbLimit non-default AS-external-LSAs in its database. OspfExtLsdbLimit MUST be set identically in all routers attached to the OSPF backbone and/or any regular OSPF area. (i.e., OSPF stub areas and NSSAs are excluded).
OBJECT-TYPE    
  Integer32 -1..'7FFFFFFF'h  

ospfMulticastExtensions 1.3.6.1.2.1.14.1.12
A Bit Mask indicating whether the router is forwarding IP multicast (Class D) datagrams based on the algorithms defined in the Multi- cast Extensions to OSPF. Bit 0, if set, indicates that the router can forward IP multicast datagrams in the router's directly attached areas (called intra-area mul- ticast routing). Bit 1, if set, indicates that the router can forward IP multicast datagrams between OSPF areas (called inter-area multicast routing). Bit 2, if set, indicates that the router can forward IP multicast datagrams between Auto- nomous Systems (called inter-AS multicast rout- ing). Only certain combinations of bit settings are allowed, namely: 0 (no multicast forwarding is enabled), 1 (intra-area multicasting only), 3 (intra-area and inter-area multicasting), 5 (intra-area and inter-AS multicasting) and 7 (multicasting everywhere). By default, no mul- ticast forwarding is enabled.
OBJECT-TYPE    
  Integer32  

ospfExitOverflowInterval 1.3.6.1.2.1.14.1.13
The number of seconds that, after entering OverflowState, a router will attempt to leave OverflowState. This allows the router to again originate non-default AS-external-LSAs. When set to 0, the router will not leave Overflow- State until restarted.
OBJECT-TYPE    
  PositiveInteger  

ospfDemandExtensions 1.3.6.1.2.1.14.1.14
The router's support for demand routing.
OBJECT-TYPE    
  TruthValue  

ospfAreaTable 1.3.6.1.2.1.14.2
Information describing the configured parame- ters and cumulative statistics of the router's attached areas.
OBJECT-TYPE    
  SEQUENCE OF  
    OspfAreaEntry

ospfAreaEntry 1.3.6.1.2.1.14.2.1
Information describing the configured parame- ters and cumulative statistics of one of the router's attached areas.
OBJECT-TYPE    
  OspfAreaEntry  

ospfAreaId 1.3.6.1.2.1.14.2.1.1
A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone.
OBJECT-TYPE    
  AreaID  

ospfAuthType 1.3.6.1.2.1.14.2.1.2
The authentication type specified for an area. Additional authentication types may be assigned locally on a per Area basis.
OBJECT-TYPE    
  Integer32  

ospfImportAsExtern 1.3.6.1.2.1.14.2.1.3
The area's support for importing AS external link- state advertisements.
OBJECT-TYPE    
  INTEGER importExternal(1), importNoExternal(2), importNssa(3)  

ospfSpfRuns 1.3.6.1.2.1.14.2.1.4
The number of times that the intra-area route table has been calculated using this area's link-state database. This is typically done using Dijkstra's algorithm.
OBJECT-TYPE    
  Counter32  

ospfAreaBdrRtrCount 1.3.6.1.2.1.14.2.1.5
The total number of area border routers reach- able within this area. This is initially zero, and is calculated in each SPF Pass.
OBJECT-TYPE    
  Gauge32  

ospfAsBdrRtrCount 1.3.6.1.2.1.14.2.1.6
The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass.
OBJECT-TYPE    
  Gauge32  

ospfAreaLsaCount 1.3.6.1.2.1.14.2.1.7
The total number of link-state advertisements in this area's link-state database, excluding AS External LSA's.
OBJECT-TYPE    
  Gauge32  

ospfAreaLsaCksumSum 1.3.6.1.2.1.14.2.1.8
The 32-bit unsigned sum of the link-state ad- vertisements' LS checksums contained in this area's link-state database. This sum excludes external (LS type 5) link-state advertisements. The sum can be used to determine if there has been a change in a router's link state data- base, and to compare the link-state database of two routers.
OBJECT-TYPE    
  Integer32  

ospfAreaSummary 1.3.6.1.2.1.14.2.1.9
The variable ospfAreaSummary controls the im- port of summary LSAs into stub areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate summary LSAs into the stub area. It will rely entirely on its de- fault route. If it is sendAreaSummary, the router will both summarize and propagate summary LSAs.
OBJECT-TYPE    
  INTEGER noAreaSummary(1), sendAreaSummary(2)  

ospfAreaStatus 1.3.6.1.2.1.14.2.1.10
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

ospfStubAreaTable 1.3.6.1.2.1.14.3
The set of metrics that will be advertised by a default Area Border Router into a stub area.
OBJECT-TYPE    
  SEQUENCE OF  
    OspfStubAreaEntry

ospfStubAreaEntry 1.3.6.1.2.1.14.3.1
The metric for a given Type of Service that will be advertised by a default Area Border Router into a stub area.
OBJECT-TYPE    
  OspfStubAreaEntry  

ospfStubAreaId 1.3.6.1.2.1.14.3.1.1
The 32 bit identifier for the Stub Area. On creation, this can be derived from the in- stance.
OBJECT-TYPE    
  AreaID  

ospfStubTOS 1.3.6.1.2.1.14.3.1.2
The Type of Service associated with the metric. On creation, this can be derived from the instance.
OBJECT-TYPE    
  TOSType  

ospfStubMetric 1.3.6.1.2.1.14.3.1.3
The metric value applied at the indicated type of service. By default, this equals the least metric at the type of service among the inter- faces to other areas.
OBJECT-TYPE    
  BigMetric  

ospfStubStatus 1.3.6.1.2.1.14.3.1.4
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

ospfStubMetricType 1.3.6.1.2.1.14.3.1.5
This variable displays the type of metric ad- vertised as a default route.
OBJECT-TYPE    
  INTEGER ospfMetric(1), comparableCost(2), nonComparable(3)  

ospfLsdbTable 1.3.6.1.2.1.14.4
The OSPF Process's Link State Database.
OBJECT-TYPE    
  SEQUENCE OF  
    OspfLsdbEntry

ospfLsdbEntry 1.3.6.1.2.1.14.4.1
A single Link State Advertisement.
OBJECT-TYPE    
  OspfLsdbEntry  

ospfLsdbAreaId 1.3.6.1.2.1.14.4.1.1
The 32 bit identifier of the Area from which the LSA was received.
OBJECT-TYPE    
  AreaID  

ospfLsdbType 1.3.6.1.2.1.14.4.1.2
The type of the link state advertisement. Each link state type has a separate advertise- ment format.
OBJECT-TYPE    
  INTEGER routerLink(1), networkLink(2), summaryLink(3), asSummaryLink(4), asExternalLink(5), multicastLink(6), nssaExternalLink(7)  

ospfLsdbLsid 1.3.6.1.2.1.14.4.1.3
The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
OBJECT-TYPE    
  IpAddress  

ospfLsdbRouterId 1.3.6.1.2.1.14.4.1.4
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
OBJECT-TYPE    
  RouterID  

ospfLsdbSequence 1.3.6.1.2.1.14.4.1.5
The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
OBJECT-TYPE    
  Integer32  

ospfLsdbAge 1.3.6.1.2.1.14.4.1.6
This field is the age of the link state adver- tisement in seconds.
OBJECT-TYPE    
  Integer32  

ospfLsdbChecksum 1.3.6.1.2.1.14.4.1.7
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
OBJECT-TYPE    
  Integer32  

ospfLsdbAdvertisement 1.3.6.1.2.1.14.4.1.8
The entire Link State Advertisement, including its header.
OBJECT-TYPE    
  OCTET STRING SIZE(1..65535)  

ospfAreaRangeTable 1.3.6.1.2.1.14.5
A range if IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255
OBJECT-TYPE    
  SEQUENCE OF  
    OspfAreaRangeEntry

ospfAreaRangeEntry 1.3.6.1.2.1.14.5.1
A range if IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255
OBJECT-TYPE    
  OspfAreaRangeEntry  

ospfAreaRangeAreaId 1.3.6.1.2.1.14.5.1.1
The Area the Address Range is to be found within.
OBJECT-TYPE    
  AreaID  

ospfAreaRangeNet 1.3.6.1.2.1.14.5.1.2
The IP Address of the Net or Subnet indicated by the range.
OBJECT-TYPE    
  IpAddress  

ospfAreaRangeMask 1.3.6.1.2.1.14.5.1.3
The Subnet Mask that pertains to the Net or Subnet.
OBJECT-TYPE    
  IpAddress  

ospfAreaRangeStatus 1.3.6.1.2.1.14.5.1.4
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

ospfAreaRangeEffect 1.3.6.1.2.1.14.5.1.5
Subnets subsumed by ranges either trigger the advertisement of the indicated summary (adver- tiseMatching), or result in the subnet's not being advertised at all outside the area.
OBJECT-TYPE    
  INTEGER advertiseMatching(1), doNotAdvertiseMatching(2)  

ospfHostTable 1.3.6.1.2.1.14.6
The list of Hosts, and their metrics, that the router will advertise as host routes.
OBJECT-TYPE    
  SEQUENCE OF  
    OspfHostEntry

ospfHostEntry 1.3.6.1.2.1.14.6.1
A metric to be advertised, for a given type of service, when a given host is reachable.
OBJECT-TYPE    
  OspfHostEntry  

ospfHostIpAddress 1.3.6.1.2.1.14.6.1.1
The IP Address of the Host.
OBJECT-TYPE    
  IpAddress  

ospfHostTOS 1.3.6.1.2.1.14.6.1.2
The Type of Service of the route being config- ured.
OBJECT-TYPE    
  TOSType  

ospfHostMetric 1.3.6.1.2.1.14.6.1.3
The Metric to be advertised.
OBJECT-TYPE    
  Metric  

ospfHostStatus 1.3.6.1.2.1.14.6.1.4
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

ospfHostAreaID 1.3.6.1.2.1.14.6.1.5
The Area the Host Entry is to be found within. By default, the area that a subsuming OSPF in- terface is in, or 0.0.0.0
OBJECT-TYPE    
  AreaID  

ospfIfTable 1.3.6.1.2.1.14.7
The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF.
OBJECT-TYPE    
  SEQUENCE OF  
    OspfIfEntry

ospfIfEntry 1.3.6.1.2.1.14.7.1
The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF.
OBJECT-TYPE    
  OspfIfEntry  

ospfIfIpAddress 1.3.6.1.2.1.14.7.1.1
The IP address of this OSPF interface.
OBJECT-TYPE    
  IpAddress  

ospfAddressLessIf 1.3.6.1.2.1.14.7.1.2
For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address.
OBJECT-TYPE    
  Integer32  

ospfIfAreaId 1.3.6.1.2.1.14.7.1.3
A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.
OBJECT-TYPE    
  AreaID  

ospfIfType 1.3.6.1.2.1.14.7.1.4
The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broad- cast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25 and similar technologies take the value 'nbma', and links that are definitively point to point take the value 'pointToPoint'.
OBJECT-TYPE    
  INTEGER broadcast(1), nbma(2), pointToPoint(3), pointToMultipoint(5)  

ospfIfAdminStat 1.3.6.1.2.1.14.7.1.5
The OSPF interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.
OBJECT-TYPE    
  Status  

ospfIfRtrPriority 1.3.6.1.2.1.14.7.1.6
The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker.
OBJECT-TYPE    
  DesignatedRouterPriority  

ospfIfTransitDelay 1.3.6.1.2.1.14.7.1.7
The estimated number of seconds it takes to transmit a link state update packet over this interface.
OBJECT-TYPE    
  UpToMaxAge  

ospfIfRetransInterval 1.3.6.1.2.1.14.7.1.8
The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets.
OBJECT-TYPE    
  UpToMaxAge  

ospfIfHelloInterval 1.3.6.1.2.1.14.7.1.9
The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a common network.
OBJECT-TYPE    
  HelloRange  

ospfIfRtrDeadInterval 1.3.6.1.2.1.14.7.1.10
The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
OBJECT-TYPE    
  PositiveInteger  

ospfIfPollInterval 1.3.6.1.2.1.14.7.1.11
The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor.
OBJECT-TYPE    
  PositiveInteger  

ospfIfState 1.3.6.1.2.1.14.7.1.12
The OSPF Interface State.
OBJECT-TYPE    
  INTEGER down(1), loopback(2), waiting(3), pointToPoint(4), designatedRouter(5), backupDesignatedRouter(6), otherDesignatedRouter(7)  

ospfIfDesignatedRouter 1.3.6.1.2.1.14.7.1.13
The IP Address of the Designated Router.
OBJECT-TYPE    
  IpAddress  

ospfIfBackupDesignatedRouter 1.3.6.1.2.1.14.7.1.14
The IP Address of the Backup Designated Router.
OBJECT-TYPE    
  IpAddress  

ospfIfEvents 1.3.6.1.2.1.14.7.1.15
The number of times this OSPF interface has changed its state, or an error has occurred.
OBJECT-TYPE    
  Counter32  

ospfIfAuthKey 1.3.6.1.2.1.14.7.1.16
The Authentication Key. If the Area's Author- ization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfIfAuthKey always returns an Oc- tet String of length zero.
OBJECT-TYPE    
  OCTET STRING SIZE(0..256)  

ospfIfStatus 1.3.6.1.2.1.14.7.1.17
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

ospfIfMulticastForwarding 1.3.6.1.2.1.14.7.1.18
The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting ospfMulticastForwarding to 0 effective- ly disables all multicast forwarding.
OBJECT-TYPE    
  INTEGER blocked(1), multicast(2), unicast(3)  

ospfIfDemand 1.3.6.1.2.1.14.7.1.19
Indicates whether Demand OSPF procedures (hel- lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this interface.
OBJECT-TYPE    
  TruthValue  

ospfIfAuthType 1.3.6.1.2.1.14.7.1.20
The authentication type specified for an in- terface. Additional authentication types may be assigned locally.
OBJECT-TYPE    
  INTEGER 0..255  

ospfIfMetricTable 1.3.6.1.2.1.14.8
The TOS metrics for a non-virtual interface identified by the interface index.
OBJECT-TYPE    
  SEQUENCE OF  
    OspfIfMetricEntry

ospfIfMetricEntry 1.3.6.1.2.1.14.8.1
A particular TOS metric for a non-virtual in- terface identified by the interface index.
OBJECT-TYPE    
  OspfIfMetricEntry  

ospfIfMetricIpAddress 1.3.6.1.2.1.14.8.1.1
The IP address of this OSPF interface. On row creation, this can be derived from the in- stance.
OBJECT-TYPE    
  IpAddress  

ospfIfMetricAddressLessIf 1.3.6.1.2.1.14.8.1.2
For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the value of ifIndex for in- terfaces having no IP Address. On row crea- tion, this can be derived from the instance.
OBJECT-TYPE    
  Integer32  

ospfIfMetricTOS 1.3.6.1.2.1.14.8.1.3
The type of service metric being referenced. On row creation, this can be derived from the instance.
OBJECT-TYPE    
  TOSType  

ospfIfMetricValue 1.3.6.1.2.1.14.8.1.4
The metric of using this type of service on this interface. The default value of the TOS 0 Metric is 10^8 / ifSpeed.
OBJECT-TYPE    
  Metric  

ospfIfMetricStatus 1.3.6.1.2.1.14.8.1.5
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

ospfVirtIfTable 1.3.6.1.2.1.14.9
Information about this router's virtual inter- faces.
OBJECT-TYPE    
  SEQUENCE OF  
    OspfVirtIfEntry

ospfVirtIfEntry 1.3.6.1.2.1.14.9.1
Information about a single Virtual Interface.
OBJECT-TYPE    
  OspfVirtIfEntry  

ospfVirtIfAreaId 1.3.6.1.2.1.14.9.1.1
The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0
OBJECT-TYPE    
  AreaID  

ospfVirtIfNeighbor 1.3.6.1.2.1.14.9.1.2
The Router ID of the Virtual Neighbor.
OBJECT-TYPE    
  RouterID  

ospfVirtIfTransitDelay 1.3.6.1.2.1.14.9.1.3
The estimated number of seconds it takes to transmit a link- state update packet over this interface.
OBJECT-TYPE    
  UpToMaxAge  

ospfVirtIfRetransInterval 1.3.6.1.2.1.14.9.1.4
The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. This value should be well over the expected round- trip time.
OBJECT-TYPE    
  UpToMaxAge  

ospfVirtIfHelloInterval 1.3.6.1.2.1.14.9.1.5
The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor.
OBJECT-TYPE    
  HelloRange  

ospfVirtIfRtrDeadInterval 1.3.6.1.2.1.14.9.1.6
The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neigh- bor.
OBJECT-TYPE    
  PositiveInteger  

ospfVirtIfState 1.3.6.1.2.1.14.9.1.7
OSPF virtual interface states.
OBJECT-TYPE    
  INTEGER down(1), pointToPoint(4)  

ospfVirtIfEvents 1.3.6.1.2.1.14.9.1.8
The number of state changes or error events on this Virtual Link
OBJECT-TYPE    
  Counter32  

ospfVirtIfAuthKey 1.3.6.1.2.1.14.9.1.9
If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 oc- tets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfVifAuthKey always returns a string of length zero.
OBJECT-TYPE    
  OCTET STRING SIZE(0..256)  

ospfVirtIfStatus 1.3.6.1.2.1.14.9.1.10
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

ospfVirtIfAuthType 1.3.6.1.2.1.14.9.1.11
The authentication type specified for a virtu- al interface. Additional authentication types may be assigned locally.
OBJECT-TYPE    
  INTEGER 0..255  

ospfNbrTable 1.3.6.1.2.1.14.10
A table of non-virtual neighbor information.
OBJECT-TYPE    
  SEQUENCE OF  
    OspfNbrEntry

ospfNbrEntry 1.3.6.1.2.1.14.10.1
The information regarding a single neighbor.
OBJECT-TYPE    
  OspfNbrEntry  

ospfNbrIpAddr 1.3.6.1.2.1.14.10.1.1
The IP address this neighbor is using in its IP Source Address. Note that, on addressless links, this will not be 0.0.0.0, but the ad- dress of another of the neighbor's interfaces.
OBJECT-TYPE    
  IpAddress  

ospfNbrAddressLessIndex 1.3.6.1.2.1.14.10.1.2
On an interface having an IP Address, zero. On addressless interfaces, the corresponding value of ifIndex in the Internet Standard MIB. On row creation, this can be derived from the instance.
OBJECT-TYPE    
  InterfaceIndex  

ospfNbrRtrId 1.3.6.1.2.1.14.10.1.3
A 32-bit integer (represented as a type IpAd- dress) uniquely identifying the neighboring router in the Autonomous System.
OBJECT-TYPE    
  RouterID  

ospfNbrOptions 1.3.6.1.2.1.14.10.1.4
A Bit Mask corresponding to the neighbor's op- tions field. Bit 0, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 1, if set, indicates that the associated area accepts and operates on external informa- tion; if zero, it is a stub area. Bit 2, if set, indicates that the system is ca- pable of routing IP Multicast datagrams; i.e., that it implements the Multicast Extensions to OSPF. Bit 3, if set, indicates that the associated area is an NSSA. These areas are capable of carrying type 7 external advertisements, which are translated into type 5 external advertise- ments at NSSA borders.
OBJECT-TYPE    
  Integer32  

ospfNbrPriority 1.3.6.1.2.1.14.10.1.5
The priority of this neighbor in the designat- ed router election algorithm. The value 0 sig- nifies that the neighbor is not eligible to be- come the designated router on this particular network.
OBJECT-TYPE    
  DesignatedRouterPriority  

ospfNbrState 1.3.6.1.2.1.14.10.1.6
The State of the relationship with this Neigh- bor.
OBJECT-TYPE    
  INTEGER down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)  

ospfNbrEvents 1.3.6.1.2.1.14.10.1.7
The number of times this neighbor relationship has changed state, or an error has occurred.
OBJECT-TYPE    
  Counter32  

ospfNbrLsRetransQLen 1.3.6.1.2.1.14.10.1.8
The current length of the retransmission queue.
OBJECT-TYPE    
  Gauge32  

ospfNbmaNbrStatus 1.3.6.1.2.1.14.10.1.9
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

ospfNbmaNbrPermanence 1.3.6.1.2.1.14.10.1.10
This variable displays the status of the en- try. 'dynamic' and 'permanent' refer to how the neighbor became known.
OBJECT-TYPE    
  INTEGER dynamic(1), permanent(2)  

ospfNbrHelloSuppressed 1.3.6.1.2.1.14.10.1.11
Indicates whether Hellos are being suppressed to the neighbor
OBJECT-TYPE    
  TruthValue  

ospfVirtNbrTable 1.3.6.1.2.1.14.11
A table of virtual neighbor information.
OBJECT-TYPE    
  SEQUENCE OF  
    OspfVirtNbrEntry

ospfVirtNbrEntry 1.3.6.1.2.1.14.11.1
Virtual neighbor information.
OBJECT-TYPE    
  OspfVirtNbrEntry  

ospfVirtNbrArea 1.3.6.1.2.1.14.11.1.1
The Transit Area Identifier.
OBJECT-TYPE    
  AreaID  

ospfVirtNbrRtrId 1.3.6.1.2.1.14.11.1.2
A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.
OBJECT-TYPE    
  RouterID  

ospfVirtNbrIpAddr 1.3.6.1.2.1.14.11.1.3
The IP address this Virtual Neighbor is us- ing.
OBJECT-TYPE    
  IpAddress  

ospfVirtNbrOptions 1.3.6.1.2.1.14.11.1.4
A Bit Mask corresponding to the neighbor's op- tions field. Bit 1, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 2, if set, indicates that the system is Network Multicast capable; ie, that it imple- ments OSPF Multicast Routing.
OBJECT-TYPE    
  Integer32  

ospfVirtNbrState 1.3.6.1.2.1.14.11.1.5
The state of the Virtual Neighbor Relation- ship.
OBJECT-TYPE    
  INTEGER down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)  

ospfVirtNbrEvents 1.3.6.1.2.1.14.11.1.6
The number of times this virtual link has changed its state, or an error has occurred.
OBJECT-TYPE    
  Counter32  

ospfVirtNbrLsRetransQLen 1.3.6.1.2.1.14.11.1.7
The current length of the retransmission queue.
OBJECT-TYPE    
  Gauge32  

ospfVirtNbrHelloSuppressed 1.3.6.1.2.1.14.11.1.8
Indicates whether Hellos are being suppressed to the neighbor
OBJECT-TYPE    
  TruthValue  

ospfExtLsdbTable 1.3.6.1.2.1.14.12
The OSPF Process's Links State Database.
OBJECT-TYPE    
  SEQUENCE OF  
    OspfExtLsdbEntry

ospfExtLsdbEntry 1.3.6.1.2.1.14.12.1
A single Link State Advertisement.
OBJECT-TYPE    
  OspfExtLsdbEntry  

ospfExtLsdbType 1.3.6.1.2.1.14.12.1.1
The type of the link state advertisement. Each link state type has a separate advertise- ment format.
OBJECT-TYPE    
  INTEGER asExternalLink(5)  

ospfExtLsdbLsid 1.3.6.1.2.1.14.12.1.2
The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
OBJECT-TYPE    
  IpAddress  

ospfExtLsdbRouterId 1.3.6.1.2.1.14.12.1.3
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
OBJECT-TYPE    
  RouterID  

ospfExtLsdbSequence 1.3.6.1.2.1.14.12.1.4
The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
OBJECT-TYPE    
  Integer32  

ospfExtLsdbAge 1.3.6.1.2.1.14.12.1.5
This field is the age of the link state adver- tisement in seconds.
OBJECT-TYPE    
  Integer32  

ospfExtLsdbChecksum 1.3.6.1.2.1.14.12.1.6
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
OBJECT-TYPE    
  Integer32  

ospfExtLsdbAdvertisement 1.3.6.1.2.1.14.12.1.7
The entire Link State Advertisement, including its header.
OBJECT-TYPE    
  OCTET STRING SIZE(36)  

ospfRouteGroup 1.3.6.1.2.1.14.13
OBJECT IDENTIFIER    

ospfIntraArea 1.3.6.1.2.1.14.13.1
OBJECT IDENTIFIER    

ospfInterArea 1.3.6.1.2.1.14.13.2
OBJECT IDENTIFIER    

ospfExternalType1 1.3.6.1.2.1.14.13.3
OBJECT IDENTIFIER    

ospfExternalType2 1.3.6.1.2.1.14.13.4
OBJECT IDENTIFIER    

ospfAreaAggregateTable 1.3.6.1.2.1.14.14
A range of IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255. Note that if ranges are configured such that one range sub- sumes another range (e.g., 10.0.0.0 mask 255.0.0.0 and 10.1.0.0 mask 255.255.0.0), the most specific match is the preferred one.
OBJECT-TYPE    
  SEQUENCE OF  
    OspfAreaAggregateEntry

ospfAreaAggregateEntry 1.3.6.1.2.1.14.14.1
A range of IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255. Note that if ranges are range configured such that one range subsumes another range (e.g., 10.0.0.0 mask 255.0.0.0 and 10.1.0.0 mask 255.255.0.0), the most specific match is the preferred one.
OBJECT-TYPE    
  OspfAreaAggregateEntry  

ospfAreaAggregateAreaID 1.3.6.1.2.1.14.14.1.1
The Area the Address Aggregate is to be found within.
OBJECT-TYPE    
  AreaID  

ospfAreaAggregateLsdbType 1.3.6.1.2.1.14.14.1.2
The type of the Address Aggregate. This field specifies the Lsdb type that this Address Ag- gregate applies to.
OBJECT-TYPE    
  INTEGER summaryLink(3), nssaExternalLink(7)  

ospfAreaAggregateNet 1.3.6.1.2.1.14.14.1.3
The IP Address of the Net or Subnet indicated by the range.
OBJECT-TYPE    
  IpAddress  

ospfAreaAggregateMask 1.3.6.1.2.1.14.14.1.4
The Subnet Mask that pertains to the Net or Subnet.
OBJECT-TYPE    
  IpAddress  

ospfAreaAggregateStatus 1.3.6.1.2.1.14.14.1.5
This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

ospfAreaAggregateEffect 1.3.6.1.2.1.14.14.1.6
Subnets subsumed by ranges either trigger the advertisement of the indicated aggregate (ad- vertiseMatching), or result in the subnet's not being advertised at all outside the area.
OBJECT-TYPE    
  INTEGER advertiseMatching(1), doNotAdvertiseMatching(2)  

ospfConformance 1.3.6.1.2.1.14.15
OBJECT IDENTIFIER    

ospfGroups 1.3.6.1.2.1.14.15.1
OBJECT IDENTIFIER    

ospfBasicGroup 1.3.6.1.2.1.14.15.1.1
These objects are required for OSPF systems.
OBJECT-GROUP    

ospfAreaGroup 1.3.6.1.2.1.14.15.1.2
These objects are required for OSPF systems supporting areas.
OBJECT-GROUP    

ospfStubAreaGroup 1.3.6.1.2.1.14.15.1.3
These objects are required for OSPF systems supporting stub areas.
OBJECT-GROUP    

ospfLsdbGroup 1.3.6.1.2.1.14.15.1.4
These objects are required for OSPF systems that display their link state database.
OBJECT-GROUP    

ospfAreaRangeGroup 1.3.6.1.2.1.14.15.1.5
These objects are required for non-CIDR OSPF systems that support multiple areas.
OBJECT-GROUP    

ospfHostGroup 1.3.6.1.2.1.14.15.1.6
These objects are required for OSPF systems that support attached hosts.
OBJECT-GROUP    

ospfIfGroup 1.3.6.1.2.1.14.15.1.7
These objects are required for OSPF systems.
OBJECT-GROUP    

ospfIfMetricGroup 1.3.6.1.2.1.14.15.1.8
These objects are required for OSPF systems.
OBJECT-GROUP    

ospfVirtIfGroup 1.3.6.1.2.1.14.15.1.9
These objects are required for OSPF systems.
OBJECT-GROUP    

ospfNbrGroup 1.3.6.1.2.1.14.15.1.10
These objects are required for OSPF systems.
OBJECT-GROUP    

ospfVirtNbrGroup 1.3.6.1.2.1.14.15.1.11
These objects are required for OSPF systems.
OBJECT-GROUP    

ospfExtLsdbGroup 1.3.6.1.2.1.14.15.1.12
These objects are required for OSPF systems that display their link state database.
OBJECT-GROUP    

ospfAreaAggregateGroup 1.3.6.1.2.1.14.15.1.13
These objects are required for OSPF systems.
OBJECT-GROUP    

ospfCompliances 1.3.6.1.2.1.14.15.2
OBJECT IDENTIFIER    

ospfCompliance 1.3.6.1.2.1.14.15.2.1
The compliance statement
MODULE-COMPLIANCE    

Defined Objects

AreaID  
An OSPF Area Identifier.
TEXTUAL-CONVENTION    
  IpAddress  

RouterID  
A OSPF Router Identifier.
TEXTUAL-CONVENTION    
  IpAddress  

Metric  
The OSPF Internal Metric.
TEXTUAL-CONVENTION    
  Integer32 0..'FFFF'h  

BigMetric  
The OSPF External Metric.
TEXTUAL-CONVENTION    
  Integer32 0..'FFFFFF'h  

Status  
The status of an interface: 'enabled' indicates that it is willing to communicate with other OSPF Routers, while 'disabled' indicates that it is not.
TEXTUAL-CONVENTION    
  INTEGER enabled(1), disabled(2)  

PositiveInteger  
A positive integer. Values in excess are precluded as unnecessary and prone to interoperability issues.
TEXTUAL-CONVENTION    
  Integer32 0..'7FFFFFFF'h  

HelloRange  
The range of intervals on which hello messages are exchanged.
TEXTUAL-CONVENTION    
  Integer32 1..'FFFF'h  

UpToMaxAge  
The values that one might find or configure for variables bounded by the maximum age of an LSA.
TEXTUAL-CONVENTION    
  Integer32 0..3600  

InterfaceIndex  
The range of ifIndex.
TEXTUAL-CONVENTION    
  Integer32  

DesignatedRouterPriority  
The values defined for the priority of a system for becoming the designated router.
TEXTUAL-CONVENTION    
  Integer32 0..'FF'h  

TOSType  
Type of Service is defined as a mapping to the IP Type of Service Flags as defined in the IP Forwarding Table MIB +-----+-----+-----+-----+-----+-----+-----+-----+ | | | | | PRECEDENCE | TYPE OF SERVICE | 0 | | | | | +-----+-----+-----+-----+-----+-----+-----+-----+ IP TOS IP TOS Field Policy Field Policy Contents Code Contents Code 0 0 0 0 ==> 0 0 0 0 1 ==> 2 0 0 1 0 ==> 4 0 0 1 1 ==> 6 0 1 0 0 ==> 8 0 1 0 1 ==> 10 0 1 1 0 ==> 12 0 1 1 1 ==> 14 1 0 0 0 ==> 16 1 0 0 1 ==> 18 1 0 1 0 ==> 20 1 0 1 1 ==> 22 1 1 0 0 ==> 24 1 1 0 1 ==> 26 1 1 1 0 ==> 28 1 1 1 1 ==> 30 The remaining values are left for future definition.
TEXTUAL-CONVENTION    
  Integer32 0..30  

OspfAreaEntry  
SEQUENCE    
  AreaID as ospfAreaId  
  Integer32 as ospfAuthType  
  INTEGER as ospfImportAsExtern  
  Counter32 as ospfSpfRuns  
  Gauge32 as ospfAreaBdrRtrCount  
  Gauge32 as ospfAsBdrRtrCount  
  Gauge32 as ospfAreaLsaCount  
  Integer32 as ospfAreaLsaCksumSum  
  INTEGER as ospfAreaSummary  
  RowStatus as ospfAreaStatus  

OspfStubAreaEntry  
SEQUENCE    
  AreaID as ospfStubAreaId  
  TOSType as ospfStubTOS  
  BigMetric as ospfStubMetric  
  RowStatus as ospfStubStatus  
  INTEGER as ospfStubMetricType  

OspfLsdbEntry  
SEQUENCE    
  AreaID as ospfLsdbAreaId  
  INTEGER as ospfLsdbType  
  IpAddress as ospfLsdbLsid  
  RouterID as ospfLsdbRouterId  
  Integer32 as ospfLsdbSequence  
  Integer32 as ospfLsdbAge  
  Integer32 as ospfLsdbChecksum  
  OCTET STRING as ospfLsdbAdvertisement  

OspfAreaRangeEntry  
SEQUENCE    
  AreaID as ospfAreaRangeAreaId  
  IpAddress as ospfAreaRangeNet  
  IpAddress as ospfAreaRangeMask  
  RowStatus as ospfAreaRangeStatus  
  INTEGER as ospfAreaRangeEffect  

OspfHostEntry  
SEQUENCE    
  IpAddress as ospfHostIpAddress  
  TOSType as ospfHostTOS  
  Metric as ospfHostMetric  
  RowStatus as ospfHostStatus  
  AreaID as ospfHostAreaID  

OspfIfEntry  
SEQUENCE    
  IpAddress as ospfIfIpAddress  
  Integer32 as ospfAddressLessIf  
  AreaID as ospfIfAreaId  
  INTEGER as ospfIfType  
  Status as ospfIfAdminStat  
  DesignatedRouterPriority as ospfIfRtrPriority  
  UpToMaxAge as ospfIfTransitDelay  
  UpToMaxAge as ospfIfRetransInterval  
  HelloRange as ospfIfHelloInterval  
  PositiveInteger as ospfIfRtrDeadInterval  
  PositiveInteger as ospfIfPollInterval  
  INTEGER as ospfIfState  
  IpAddress as ospfIfDesignatedRouter  
  IpAddress as ospfIfBackupDesignatedRouter  
  Counter32 as ospfIfEvents  
  INTEGER as ospfIfAuthType  
  OCTET STRING as ospfIfAuthKey  
  RowStatus as ospfIfStatus  
  INTEGER as ospfIfMulticastForwarding  
  TruthValue as ospfIfDemand  

OspfIfMetricEntry  
SEQUENCE    
  IpAddress as ospfIfMetricIpAddress  
  Integer32 as ospfIfMetricAddressLessIf  
  TOSType as ospfIfMetricTOS  
  Metric as ospfIfMetricValue  
  RowStatus as ospfIfMetricStatus  

OspfVirtIfEntry  
SEQUENCE    
  AreaID as ospfVirtIfAreaId  
  RouterID as ospfVirtIfNeighbor  
  UpToMaxAge as ospfVirtIfTransitDelay  
  UpToMaxAge as ospfVirtIfRetransInterval  
  HelloRange as ospfVirtIfHelloInterval  
  PositiveInteger as ospfVirtIfRtrDeadInterval  
  INTEGER as ospfVirtIfState  
  Counter32 as ospfVirtIfEvents  
  INTEGER as ospfVirtIfAuthType  
  OCTET STRING as ospfVirtIfAuthKey  
  RowStatus as ospfVirtIfStatus  

OspfNbrEntry  
SEQUENCE    
  IpAddress as ospfNbrIpAddr  
  InterfaceIndex as ospfNbrAddressLessIndex  
  RouterID as ospfNbrRtrId  
  Integer32 as ospfNbrOptions  
  DesignatedRouterPriority as ospfNbrPriority  
  INTEGER as ospfNbrState  
  Counter32 as ospfNbrEvents  
  Gauge32 as ospfNbrLsRetransQLen  
  RowStatus as ospfNbmaNbrStatus  
  INTEGER as ospfNbmaNbrPermanence  
  TruthValue as ospfNbrHelloSuppressed  

OspfVirtNbrEntry  
SEQUENCE    
  AreaID as ospfVirtNbrArea  
  RouterID as ospfVirtNbrRtrId  
  IpAddress as ospfVirtNbrIpAddr  
  Integer32 as ospfVirtNbrOptions  
  INTEGER as ospfVirtNbrState  
  Counter32 as ospfVirtNbrEvents  
  Gauge32 as ospfVirtNbrLsRetransQLen  
  TruthValue as ospfVirtNbrHelloSuppressed  

OspfExtLsdbEntry  
SEQUENCE    
  INTEGER as ospfExtLsdbType  
  IpAddress as ospfExtLsdbLsid  
  RouterID as ospfExtLsdbRouterId  
  Integer32 as ospfExtLsdbSequence  
  Integer32 as ospfExtLsdbAge  
  Integer32 as ospfExtLsdbChecksum  
  OCTET STRING as ospfExtLsdbAdvertisement  

OspfAreaAggregateEntry  
SEQUENCE    
  AreaID as ospfAreaAggregateAreaID  
  INTEGER as ospfAreaAggregateLsdbType  
  IpAddress as ospfAreaAggregateNet  
  IpAddress as ospfAreaAggregateMask  
  RowStatus as ospfAreaAggregateStatus  
  INTEGER as ospfAreaAggregateEffect