PANDATEL-MODEM-MIB

File: PANDATEL-MODEM-MIB.mib (71928 bytes)

Imported modules

RFC-1215 RFC1155-SMI RFC1213-MIB
RFC-1212

Imported symbols

TRAP-TYPE enterprises Counter
IpAddress Gauge TimeTicks
DisplayString OBJECT-TYPE

Defined Objects

pandatel 1.3.6.1.4.1.760
OBJECT IDENTIFIER    

mibs 1.3.6.1.4.1.760.1
OBJECT IDENTIFIER    

products 1.3.6.1.4.1.760.1.1
OBJECT IDENTIFIER    

wan-products 1.3.6.1.4.1.760.1.1.2
OBJECT IDENTIFIER    

mdm-mgmt 1.3.6.1.4.1.760.1.1.2.1
OBJECT IDENTIFIER    

mdmGroup 1.3.6.1.4.1.760.1.1.2.1.1
OBJECT IDENTIFIER    

rackAdded 1.3.6.1.4.1.760.1.1.2.1.1
This trap will be sent when a rack is added to the managed chassis. The rack index of the new rack is sent along with this trap.
TRAP-TYPE    
  rackType  

mdmInstalledRacks 1.3.6.1.4.1.760.1.1.2.1.1.1
This is the number of currently installed modem racks.
OBJECT-TYPE    
  INTEGER  

mdmInstalledModems 1.3.6.1.4.1.760.1.1.2.1.1.2
This is the number of currently installed modems
OBJECT-TYPE    
  INTEGER  

mdmLoopModeTraps 1.3.6.1.4.1.760.1.1.2.1.1.3
This enables or disables traps generated by a Loop Mode status change at any local modem port of one of the installed modems (values: disable, enable).
OBJECT-TYPE    
  INTEGER disable(2), enable(3)  

mdmCurrentDate 1.3.6.1.4.1.760.1.1.2.1.1.13
This indicate the current date as 'mm/dd/yy'. The date will be used for local management.
OBJECT-TYPE    
  DisplayString  

mdmCurrentTime 1.3.6.1.4.1.760.1.1.2.1.1.14
This indicate the current time as 'hh:mm:ss'. The time will be used for local management.
OBJECT-TYPE    
  DisplayString  

mdmRackTable 1.3.6.1.4.1.760.1.1.2.1.2
Table which contains information about the installed racks.
OBJECT-TYPE    
  SEQUENCE OF  
    RackEntry

rackRemoved 1.3.6.1.4.1.760.1.1.2.1.2
This trap will be sent when a rack is removed from the managed chassis. The rack index of the removed rack is sent along with this trap.
TRAP-TYPE    
  rackType  

rackEntry 1.3.6.1.4.1.760.1.1.2.1.2.1
The index of the table.
OBJECT-TYPE    
  RackEntry  

rackRack 1.3.6.1.4.1.760.1.1.2.1.2.1.1
The index of this particular modem rack in the stack. The index of the rack which contains the agent should have the number 1.
OBJECT-TYPE    
  INTEGER  

rackType 1.3.6.1.4.1.760.1.1.2.1.2.1.2
This entry shows the type number of the rack.
OBJECT-TYPE    
  INTEGER other(1), rack-10s-3hu(2), rack-12s-3hu(3), rack-10s-6hu(4), rack-6s-9s-6hu(5), device-stack-15s(6), rack-8s-4hu(7), rack-10s-2c-6hu(8), hs-rack-10s-3hu(9), rack-8s-2c-6hu(10), hs-rack-3s-1c-3hu(11), rack-1s-1c-1hu(12), rack-3s-1c-1hu(13)  

rackDescription 1.3.6.1.4.1.760.1.1.2.1.2.1.3
A verbal description of the modem rack.
OBJECT-TYPE    
  DisplayString  

rackModemSlots 1.3.6.1.4.1.760.1.1.2.1.2.1.4
This entry shows the number of slots for modem cards in the rack.
OBJECT-TYPE    
  INTEGER  

rackModems 1.3.6.1.4.1.760.1.1.2.1.2.1.5
This entry shows the number of modems currently installed in the rack.
OBJECT-TYPE    
  INTEGER  

rackPowerSupplySlots 1.3.6.1.4.1.760.1.1.2.1.2.1.6
This entry shows the number of slots for power supplies in the rack.
OBJECT-TYPE    
  INTEGER unknown(999)  

rackPowerSupplies 1.3.6.1.4.1.760.1.1.2.1.2.1.7
This entry shows the number of power supplies currently installed in the rack.
OBJECT-TYPE    
  INTEGER unknown(999)  

mdmModemTable 1.3.6.1.4.1.760.1.1.2.1.3
Table which contains general information about the installed modems.
OBJECT-TYPE    
  SEQUENCE OF  
    ModemEntry

modemAdded 1.3.6.1.4.1.760.1.1.2.1.3
This trap will be sent when a modem is added. The rack number and the index of the new modem is sent along with this trap.
TRAP-TYPE    
  viType  

modemEntry 1.3.6.1.4.1.760.1.1.2.1.3.1
The index of the table.
OBJECT-TYPE    
  ModemEntry  

mdmRack 1.3.6.1.4.1.760.1.1.2.1.3.1.1
The index of the rack where the modem is installed.
OBJECT-TYPE    
  INTEGER  

mdmModem 1.3.6.1.4.1.760.1.1.2.1.3.1.2
The index of this particular modem in the rack. The value corresponds with the slot where the modem is inserted.
OBJECT-TYPE    
  INTEGER  

mdmDescription 1.3.6.1.4.1.760.1.1.2.1.3.1.3
A verbal description of the modem.
OBJECT-TYPE    
  DisplayString  

mdmUserName 1.3.6.1.4.1.760.1.1.2.1.3.1.4
A verbal description of the modem which can be changed by the manager.
OBJECT-TYPE    
  DisplayString  

mdmSelfTest 1.3.6.1.4.1.760.1.1.2.1.3.1.5
This entry enables the execution of a selftest. Write requests with values other than 'start' or 'cancel' will be rejected. The result will be found in mdmSelfTestResult.
OBJECT-TYPE    
  INTEGER start(1), cancel(2)  

mdmSelfTestResult 1.3.6.1.4.1.760.1.1.2.1.3.1.6
This entry shows the result status of the last modem-dependent self test. After start, the status may change to 'running' before the first error that occured is displayed. If no error was detected the status changes to 'ok'.
OBJECT-TYPE    
  INTEGER started(3), running(4), ram-error(5), rom-error(6), eeprom-error(7), line-if-error(8), other-error(97), never-started(98), cancelled(99), ok(100)  

mdmRemoteAccessStatus 1.3.6.1.4.1.760.1.1.2.1.3.1.7
This entry shows the access status to the remote counterpart of the modem. The standard value depends on the device. Some remote modems are always accessible, others are not accessible or can be switched to both modes (see 'mdmForcedRemoteAccess' in the specific modem MIB).
OBJECT-TYPE    
  INTEGER access(2), no-access(3)  

mdmInterfacePorts 1.3.6.1.4.1.760.1.1.2.1.3.1.8
This entry indicates the number of interface ports of the modem. An interface port connects an external device.
OBJECT-TYPE    
  INTEGER  

mdmLinePorts 1.3.6.1.4.1.760.1.1.2.1.3.1.9
This entry indicates the number of line ports of the modem. A line port connects a remote modem.
OBJECT-TYPE    
  INTEGER  

mdmVerInfoTable 1.3.6.1.4.1.760.1.1.2.1.4
Table which contains information about the installed modems' versions.
OBJECT-TYPE    
  SEQUENCE OF  
    VerInfoEntry

modemRemoved 1.3.6.1.4.1.760.1.1.2.1.4
This trap will be sent when a modem in one of the slots is removed. The rack number and the index of the removed modem is sent along with this trap.
TRAP-TYPE    
  viType  

verInfoEntry 1.3.6.1.4.1.760.1.1.2.1.4.1
The index of the table.
OBJECT-TYPE    
  VerInfoEntry  

viRack 1.3.6.1.4.1.760.1.1.2.1.4.1.1
The index of the rack where the modem is installed.
OBJECT-TYPE    
  INTEGER  

viModem 1.3.6.1.4.1.760.1.1.2.1.4.1.2
The index of this particular modem in the rack. The value corresponds with the slot where the modem is inserted.
OBJECT-TYPE    
  INTEGER  

viType 1.3.6.1.4.1.760.1.1.2.1.4.1.3
This entry indicates the type of the modem.
OBJECT-TYPE    
  INTEGER not-present(0), other(1), fhfl(101), fhfl-f(102), fhfl-s(103), gm-h(201), gm-f(202), gm-d(203), gm-s(204), gm-s-f(205), gm-d-f(206), bm-p(301), bm-z(302), gx(401), fobus(501), fx(502), fx-i(503), fx-ig(504), os(505), fx-g(506), fx-ih(507), fme(601), inax(701), emx(801), cmx-ie(802), etc(901)  

viFirmwVer 1.3.6.1.4.1.760.1.1.2.1.4.1.4
This entry indicates the firmware revision of the modem.
OBJECT-TYPE    
  DisplayString  

viUnitRel 1.3.6.1.4.1.760.1.1.2.1.4.1.5
This entry indicates the hardware version and revision of the modem.
OBJECT-TYPE    
  DisplayString  

viArtNo 1.3.6.1.4.1.760.1.1.2.1.4.1.6
This entry indicates the article number of the modem.
OBJECT-TYPE    
  DisplayString  

viFrontVer 1.3.6.1.4.1.760.1.1.2.1.4.1.7
For factory purposes only.
OBJECT-TYPE    
  INTEGER other(1)  

viSerialNumber 1.3.6.1.4.1.760.1.1.2.1.4.1.8
This entry indicates the serial number of the modem.
OBJECT-TYPE    
  DisplayString  

mdmPortTable 1.3.6.1.4.1.760.1.1.2.1.5
Table which contains information about all ports.
OBJECT-TYPE    
  SEQUENCE OF  
    PortEntry

portLoopEnabled 1.3.6.1.4.1.760.1.1.2.1.5
This trap will be sent when a modem in one of the slots enables a Loop. The rack number, index of the modem, and port number is sent along with this trap.
TRAP-TYPE    
  portLoopMode  

portEntry 1.3.6.1.4.1.760.1.1.2.1.5.1
The index of the table.
OBJECT-TYPE    
  PortEntry  

portRack 1.3.6.1.4.1.760.1.1.2.1.5.1.1
The index of the rack where the modem to which this port belongs is installed.
OBJECT-TYPE    
  INTEGER  

portModem 1.3.6.1.4.1.760.1.1.2.1.5.1.2
The index of the modem to which this port belongs.
OBJECT-TYPE    
  INTEGER  

portPort 1.3.6.1.4.1.760.1.1.2.1.5.1.3
The index of the port.
OBJECT-TYPE    
  INTEGER  

portType 1.3.6.1.4.1.760.1.1.2.1.5.1.4
This entry indicates the type of the port.
OBJECT-TYPE    
  INTEGER other(1), interface-port(2), line-port(3), vt100-mgmt-port(4), outband-mgmt-port(5), backup-port(6)  

portInterfaceType 1.3.6.1.4.1.760.1.1.2.1.5.1.5
This entry indicates the type of interface of the port.
OBJECT-TYPE    
  INTEGER other(1), v24(2), v35(3), v36(4), x21(5), rs485(6), g703-e1t1(7), g703-e2t2(8), g703-64k(9), i430(10), store-loop(11), intercom(12), fo-e1t1(13), s0(14), hdsl(15), no-module(17), atm-26mb(18), g703-e3(19), g703-t3(20), sts-1(21), hssi(22), bm(34), g703-t1(39), g703-t2(40), eth-bridge(48), g703-e1(55), g703-e2(56), sts-3(66), stm-1(67), sm-fiber-820nm(130), sm-fiber-1300nm(131), sm-fiber-1550nm(132), mm-fiber-820nm(133), mm-fiber-1300nm(134), mm-fiber-1550nm(135), sm-fiber-1530-33nm(136), sm-fiber-1531-12nm(137), sm-fiber-1531-90nm(138), sm-fiber-1532-68nm(139), sm-fiber-1533-47nm(140), sm-fiber-1534-25nm(141), sm-fiber-1535-04nm(142), sm-fiber-1535-82nm(143), sm-fiber-1536-61nm(144), sm-fiber-1537-40nm(145), sm-fiber-1538-19nm(146), sm-fiber-1538-98nm(147), sm-fiber-1539-77nm(148), sm-fiber-1540-56nm(149), sm-fiber-1541-35nm(150), sm-fiber-1542-14nm(151), sm-fiber-1542-94nm(152), sm-fiber-1543-73nm(153), sm-fiber-1544-53nm(154), sm-fiber-1545-32nm(155), sm-fiber-1546-12nm(156), sm-fiber-1546-92nm(157), sm-fiber-1547-72nm(158), sm-fiber-1548-51nm(159), sm-fiber-1549-32nm(160), sm-fiber-1550-12nm(161), sm-fiber-1550-92nm(162), sm-fiber-1551-72nm(163), sm-fiber-1552-52nm(164), sm-fiber-1553-33nm(165), sm-fiber-1554-13nm(166), sm-fiber-1554-94nm(167), sm-fiber-1555-75nm(168), sm-fiber-1556-55nm(169), sm-fiber-1557-36nm(170), sm-fiber-1558-17nm(171), sm-fiber-1558-98nm(172), sm-fiber-1559-79nm(173), sm-fiber-1560-61nm(174), sm-fiber-1561-42nm(175), sm-fiber-1562-23nm(176), sm-fiber-1563-05nm(177), sm-fiber-1563-86nm(178), sm-fiber-1564-68nm(179), sm-fiber-1565-50nm(180), sm-1300-1550nm(181), sm-1550-1300nm(182), mm-820-1300nm(183), mm-1300-820nm(184), sm-fiber-1480nm(185), sm-fiber-1510nm(186), sm-fiber-1538nm(187), sm-fiber-1553nm(188), sm-mm-fiber-1310nm(189), missing(999)  

portConnector 1.3.6.1.4.1.760.1.1.2.1.5.1.6
This entry indicates the connector type of the port.
OBJECT-TYPE    
  INTEGER other(1), single-fiber(2), dual-fiber(3), bnc(4), dpc(5), rj45(7), ics(8), mic(9), db-9-f(10), db-9-m(11), db-15-f(12), db-15-m(13), db-25-f(14), db-25-m(15), db-37-f(16), db-37-m(17), winch-f(18), winch-m(19), mini-c(20), minimicro(21), escon(22), e2000(23), single-sc(24), single-fc(25), single-st(26), dual-sc(27), dual-fc(28), dual-st(29), single-sc-apc(30), single-fc-apc(31), dual-sc-apc(32), dual-fc-apc(33), single-lc(34), single-lc-apc(35), dual-lc(36), dual-lc-apc(37), mt-rj(38), single-sc-45(39), dual-sc-45(40), unknown(997), virtual(998), not-installed(999)  

portLoopMode 1.3.6.1.4.1.760.1.1.2.1.5.1.7
This entry indicates the loop mode of the port.
OBJECT-TYPE    
  INTEGER other(1), remote(2), digital(3), line(4), off(99)  

mdmPortSignalTable 1.3.6.1.4.1.760.1.1.2.1.6
Table which contains information about all port status signals.
OBJECT-TYPE    
  SEQUENCE OF  
    PortSignalEntry

portLoopDisabled 1.3.6.1.4.1.760.1.1.2.1.6
This trap will be sent when a modem in one of the slots disables a Loop. The rack number, index of the modem, and port number is sent along with this trap.
TRAP-TYPE    
  portLoopMode  

portSignalEntry 1.3.6.1.4.1.760.1.1.2.1.6.1
The index of the table.
OBJECT-TYPE    
  PortSignalEntry  

psignalRack 1.3.6.1.4.1.760.1.1.2.1.6.1.1
The index of the rack where the modem is installed to which the port belongs that provides the signal.
OBJECT-TYPE    
  INTEGER  

psignalModem 1.3.6.1.4.1.760.1.1.2.1.6.1.2
The index of the modem to which the port belongs that provides the signal.
OBJECT-TYPE    
  INTEGER  

psignalPort 1.3.6.1.4.1.760.1.1.2.1.6.1.3
The index of the port that provides the signal.
OBJECT-TYPE    
  INTEGER  

psignalType 1.3.6.1.4.1.760.1.1.2.1.6.1.4
This entry indicates the signal type.
OBJECT-TYPE    
  INTEGER other(1), link(2), rts(3), dcd(4), dtr(5), dsr(6), c(7), i(8), fsync(9), ais(10), lay1(11), bond(12), laser-status(13), ta(14), ca(15), eclk(16), laser-tx(17), laser-temp(18), cr(20), rd(26), td(27)  

psignalStatus 1.3.6.1.4.1.760.1.1.2.1.6.1.5
This entry indicates the current status of the signal.
OBJECT-TYPE    
  INTEGER other(1), up(2), down(3), on(4), off(5), yes(6), no(7), ok(8), fail(9), active(10), traffic(11), space(12), mark(13), high(14), low(15), sync(16)  

psignalTrap 1.3.6.1.4.1.760.1.1.2.1.6.1.6
This enables or disables traps. If Trap is enabled each transition of the signal status may cause a trap portSignalStatusGood/portSignalStatusBad.
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

mdmBERTTable 1.3.6.1.4.1.760.1.1.2.1.7
Table which contains information about all performable bit error rate tests.
OBJECT-TYPE    
  SEQUENCE OF  
    BERTEntry

portSignalStatusGood 1.3.6.1.4.1.760.1.1.2.1.7
This will be sent when a status signal of a modem port enters the 'good' status. The rack number, index of the modem, and port number is sent along with this trap.
TRAP-TYPE    
  psignalType  

bertEntry 1.3.6.1.4.1.760.1.1.2.1.7.1
The index of thetable.
OBJECT-TYPE    
  BERTEntry  

bertRack 1.3.6.1.4.1.760.1.1.2.1.7.1.1
The index of the rack where the modem is installed.
OBJECT-TYPE    
  INTEGER  

bertModem 1.3.6.1.4.1.760.1.1.2.1.7.1.2
The index of this particular modem in the rack. The value corresponds with the slot where the modem is inserted.
OBJECT-TYPE    
  INTEGER  

bertPort 1.3.6.1.4.1.760.1.1.2.1.7.1.3
The index of the port where the BER test will be performed. The modem can only perform one test at a time. The test can only be performed on a subset of ports, usually the line ports. Write requests with different port numbers will be rejected. Write requests with valid line port numbers will be rejected while the BER test is running.
OBJECT-TYPE    
  INTEGER  

bertBERTest 1.3.6.1.4.1.760.1.1.2.1.7.1.4
This entry enables the execution of a BER test. Write requests with values other than 'start' or 'stop' will be rejected.
OBJECT-TYPE    
  INTEGER start(3), stop(5)  

bertStatus 1.3.6.1.4.1.760.1.1.2.1.7.1.5
This entry indicates the status of the BER test.
OBJECT-TYPE    
  INTEGER other(1), never-started(2), start(3), running(4), stopped(6), start-failed(7)  

bertRunTime 1.3.6.1.4.1.760.1.1.2.1.7.1.6
This entry indicates the duration of the BER test in seconds.
OBJECT-TYPE    
  Counter  

bertInErrorTime 1.3.6.1.4.1.760.1.1.2.1.7.1.7
This entry shows the duration of erroneous test transmission in seconds.
OBJECT-TYPE    
  Counter  

bertErrorFreeTime 1.3.6.1.4.1.760.1.1.2.1.7.1.8
This entry shows the duration of error-free test transmission in seconds.
OBJECT-TYPE    
  Counter  

bertKbitsRecWrapped 1.3.6.1.4.1.760.1.1.2.1.7.1.9
This is the number the bertKbitsReceived counter has wrapped.
OBJECT-TYPE    
  Counter  

bertKbitsReceived 1.3.6.1.4.1.760.1.1.2.1.7.1.10
This entry indicates the number of Kbits received during the test. When the counter wraps the bertKbitRecWrapped increases by one.
OBJECT-TYPE    
  Counter  

bertErrors 1.3.6.1.4.1.760.1.1.2.1.7.1.11
This entry indicates the number of errors detected during the test.
OBJECT-TYPE    
  Counter  

bertSyncLosts 1.3.6.1.4.1.760.1.1.2.1.7.1.12
This entry indicates the number of pattern sync losts detected during the test.
OBJECT-TYPE    
  Counter  

bertSyncStatus 1.3.6.1.4.1.760.1.1.2.1.7.1.13
This entry indicates the current pattern sync status.
OBJECT-TYPE    
  INTEGER other(1), in-sync(2), no-sync(3)  

bertBitErrorRate 1.3.6.1.4.1.760.1.1.2.1.7.1.14
This entry indicates the bit error rate. It is provided as a string in the format 'd.ddE+/-dd'. Float scanf routines are capable of interpreting the string in the correct manner.
OBJECT-TYPE    
  DisplayString  

portSignalStatusBad 1.3.6.1.4.1.760.1.1.2.1.8
This trap will be sent when a status signal of a modem port enters the 'bad' status. The rack number, index of the modem, and port number is sent along with this trap.
TRAP-TYPE    
  psignalType  

mdmRemoteAccess 1.3.6.1.4.1.760.1.1.2.1.9
OBJECT IDENTIFIER    

portBackupEnabled 1.3.6.1.4.1.760.1.1.2.1.9
This trap will be sent when a modem in one of the slots enters a backup status. The first port indicates the active data port, the second the inactive port. The rack number, index of the modem, and port number is sent along with this trap.
TRAP-TYPE    
  portPort  
  portPort  

remModemTable 1.3.6.1.4.1.760.1.1.2.1.9.3
Table which contains general information about all counterparts of the installed modems.
OBJECT-TYPE    
  SEQUENCE OF  
    RemModemEntry

rmodemEntry 1.3.6.1.4.1.760.1.1.2.1.9.3.1
The index of the table.
OBJECT-TYPE    
  RemModemEntry  

rmdmRack 1.3.6.1.4.1.760.1.1.2.1.9.3.1.1
This entry indicates the index of the rack where the modem is installed that the remote modem is linked to.
OBJECT-TYPE    
  INTEGER  

rmdmModem 1.3.6.1.4.1.760.1.1.2.1.9.3.1.2
The index of the modem that the remote modem is linked to.
OBJECT-TYPE    
  INTEGER  

rmdmDescription 1.3.6.1.4.1.760.1.1.2.1.9.3.1.3
A verbal description of the remote modem.
OBJECT-TYPE    
  DisplayString  

rmdmUserName 1.3.6.1.4.1.760.1.1.2.1.9.3.1.4
A verbal description of the remote modem which can be changed by the manager.
OBJECT-TYPE    
  DisplayString  

rmdmSelfTest 1.3.6.1.4.1.760.1.1.2.1.9.3.1.5
This entry enables the execution of a selftest. Write requests with values other than 'start' or 'cancel' will be rejected. The result will be found in SelfTestResult.
OBJECT-TYPE    
  INTEGER start(1), cancel(2)  

rmdmSelfTestResult 1.3.6.1.4.1.760.1.1.2.1.9.3.1.6
This indicates the result status of the last modem-dependent self test. After start, the status may change to 'running' before the first error that occured displays. If no error was detected the status changes to 'ok'.
OBJECT-TYPE    
  INTEGER started(3), running(4), ram-error(5), rom-error(6), eeprom-error(7), line-if-error(8), other-error(97), never-started(98), cancelled(99), ok(100)  

rmdmRemoteAccessStatus 1.3.6.1.4.1.760.1.1.2.1.9.3.1.7
This entry shows the access status of the modem. The standard value depends on the device. Some modems are always accessible, others are not accessible or can be switched to both modes (see 'mdmForcedRemoteAccess' in the specific modem MIB).
OBJECT-TYPE    
  INTEGER access(2), no-access(3)  

rmdmInterfacePorts 1.3.6.1.4.1.760.1.1.2.1.9.3.1.8
This entry indicates the number of interface ports of the remote modem. An interface port connects an external device.
OBJECT-TYPE    
  INTEGER  

rmdmLinePorts 1.3.6.1.4.1.760.1.1.2.1.9.3.1.9
This entry indicates the number of line ports of the modem. A line port connects the local counterpart of the remote modem.
OBJECT-TYPE    
  INTEGER  

remVerInfoTable 1.3.6.1.4.1.760.1.1.2.1.9.4
Table which contains information about the remote modems' versions.
OBJECT-TYPE    
  SEQUENCE OF  
    RemVerInfoEntry

remVerInfoEntry 1.3.6.1.4.1.760.1.1.2.1.9.4.1
The index of the table.
OBJECT-TYPE    
  RemVerInfoEntry  

rviRack 1.3.6.1.4.1.760.1.1.2.1.9.4.1.1
The index of the rack where the modem is installed that the remote modem is linked to.
OBJECT-TYPE    
  INTEGER  

rviModem 1.3.6.1.4.1.760.1.1.2.1.9.4.1.2
The index of the modem that the remote modem is linked to.
OBJECT-TYPE    
  INTEGER  

rviType 1.3.6.1.4.1.760.1.1.2.1.9.4.1.3
This entry indicates the type of the remote modem.
OBJECT-TYPE    
  INTEGER not-present(0), other(1), fhfl(101), fhfl-f(102), fhfl-s(103), gm-h(201), gm-f(202), gm-d(203), gm-s(204), gm-s-f(205), gm-d-f(206), bm-p(301), bm-z(302), gx(401), fobus(501), fx(502), fx-i(503), fx-ig(504), fx-g(506), fx-ih(507), fme(601), inax(701), emx(801), cmx-ie(802), etc(901)  

rviFirmwVer 1.3.6.1.4.1.760.1.1.2.1.9.4.1.4
This entry indicates the firmware revision of the remote modem.
OBJECT-TYPE    
  DisplayString  

rviUnitRel 1.3.6.1.4.1.760.1.1.2.1.9.4.1.5
This entry indicates the hardware version and revision of the remote modem.
OBJECT-TYPE    
  DisplayString  

rviArtNo 1.3.6.1.4.1.760.1.1.2.1.9.4.1.6
This entry indicates the article number of the remote modem.
OBJECT-TYPE    
  DisplayString  

rviFrontVer 1.3.6.1.4.1.760.1.1.2.1.9.4.1.7
For factory purposes only.
OBJECT-TYPE    
  INTEGER other(1)  

rviSerialNumber 1.3.6.1.4.1.760.1.1.2.1.9.4.1.8
This entry indicates the serial number of the remote modem.
OBJECT-TYPE    
  DisplayString  

remPortTable 1.3.6.1.4.1.760.1.1.2.1.9.5
Table which contains information about all ports of the remote modem.
OBJECT-TYPE    
  SEQUENCE OF  
    RemPortEntry

remPortEntry 1.3.6.1.4.1.760.1.1.2.1.9.5.1
The index of the table.
OBJECT-TYPE    
  RemPortEntry  

rportRack 1.3.6.1.4.1.760.1.1.2.1.9.5.1.1
The index of the rack where the local counterpart of the remote modem is installed to which this port belongs.
OBJECT-TYPE    
  INTEGER  

rportModem 1.3.6.1.4.1.760.1.1.2.1.9.5.1.2
The index of the local counterpart of the remote modem to which this port belongs.
OBJECT-TYPE    
  INTEGER  

rportPort 1.3.6.1.4.1.760.1.1.2.1.9.5.1.3
The index of the port.
OBJECT-TYPE    
  INTEGER  

rportType 1.3.6.1.4.1.760.1.1.2.1.9.5.1.4
This entry indicates the type of the port.
OBJECT-TYPE    
  INTEGER other(1), interface-port(2), line-port(3), vt100-mgmt-port(4), outband-mgmt-port(5), backup-port(6)  

rportInterfaceType 1.3.6.1.4.1.760.1.1.2.1.9.5.1.5
This entry indicates the type of interface of the port.
OBJECT-TYPE    
  INTEGER other(1), v24(2), v35(3), v36(4), x21(5), rs485(6), g703-e1t1(7), g703-e2t2(8), g703-64k(9), i430(10), store-loop(11), intercom(12), fo-e1t1(13), s0(14), hdsl(15), no-module(17), atm-26mb(18), g703-e3(19), g703-t3(20), sts-1(21), hssi(22), bm(34), g703-t1(39), g703-t2(40), eth-bridge(48), g703-e1(55), g703-e2(56), sts-3(66), stm-1(67), sm-fiber-820nm(130), sm-fiber-1300nm(131), sm-fiber-1550nm(132), mm-fiber-820nm(133), mm-fiber-1300nm(134), mm-fiber-1550nm(135), sm-fiber-1530-33nm(136), sm-fiber-1531-12nm(137), sm-fiber-1531-90nm(138), sm-fiber-1532-68nm(139), sm-fiber-1533-47nm(140), sm-fiber-1534-25nm(141), sm-fiber-1535-04nm(142), sm-fiber-1535-82nm(143), sm-fiber-1536-61nm(144), sm-fiber-1537-40nm(145), sm-fiber-1538-19nm(146), sm-fiber-1538-98nm(147), sm-fiber-1539-77nm(148), sm-fiber-1540-56nm(149), sm-fiber-1541-35nm(150), sm-fiber-1542-14nm(151), sm-fiber-1542-94nm(152), sm-fiber-1543-73nm(153), sm-fiber-1544-53nm(154), sm-fiber-1545-32nm(155), sm-fiber-1546-12nm(156), sm-fiber-1546-92nm(157), sm-fiber-1547-72nm(158), sm-fiber-1548-51nm(159), sm-fiber-1549-32nm(160), sm-fiber-1550-12nm(161), sm-fiber-1550-92nm(162), sm-fiber-1551-72nm(163), sm-fiber-1552-52nm(164), sm-fiber-1553-33nm(165), sm-fiber-1554-13nm(166), sm-fiber-1554-94nm(167), sm-fiber-1555-75nm(168), sm-fiber-1556-55nm(169), sm-fiber-1557-36nm(170), sm-fiber-1558-17nm(171), sm-fiber-1558-98nm(172), sm-fiber-1559-79nm(173), sm-fiber-1560-61nm(174), sm-fiber-1561-42nm(175), sm-fiber-1562-23nm(176), sm-fiber-1563-05nm(177), sm-fiber-1563-86nm(178), sm-fiber-1564-68nm(179), sm-fiber-1565-50nm(180), sm-1300-1550nm(181), sm-1550-1300nm(182), mm-820-1300nm(183), mm-1300-820nm(184), sm-fiber-1480nm(185), sm-fiber-1510nm(186), sm-fiber-1538nm(187), sm-fiber-1553nm(188), sm-mm-fiber-1310nm(189), missing(999)  

rportConnector 1.3.6.1.4.1.760.1.1.2.1.9.5.1.6
This entry indicates the connector type of the port.
OBJECT-TYPE    
  INTEGER other(1), single-fiber(2), dual-fiber(3), bnc(4), dpc(5), rj45(7), ics(8), mic(9), db-9-f(10), db-9-m(11), db-15-f(12), db-15-m(13), db-25-f(14), db-25-m(15), db-37-f(16), db-37-m(17), winch-f(18), winch-m(19), mini-c(20), minimicro(21), escon(22), e2000(23), single-sc(24), single-fc(25), single-st(26), dual-sc(27), dual-fc(28), dual-st(29), single-sc-apc(30), single-fc-apc(31), dual-sc-apc(32), dual-fc-apc(33), single-lc(34), single-lc-apc(35), dual-lc(36), dual-lc-apc(37), mt-rj(38), single-sc-45(39), dual-sc-45(40), unknown(997), virtual(998), not-installed(999)  

rportLoopMode 1.3.6.1.4.1.760.1.1.2.1.9.5.1.7
This entry indicates the loop mode of the port (remote, digital, line, off).
OBJECT-TYPE    
  INTEGER other(1), remote(2), digital(3), line(4), off(99)  

remPortSignalTable 1.3.6.1.4.1.760.1.1.2.1.9.6
Table which contains information about all port status signals.
OBJECT-TYPE    
  SEQUENCE OF  
    RemPortSignalEntry

remPortSignalEntry 1.3.6.1.4.1.760.1.1.2.1.9.6.1
The index of the table.
OBJECT-TYPE    
  RemPortSignalEntry  

rpsignalRack 1.3.6.1.4.1.760.1.1.2.1.9.6.1.1
The index of the rack where the local counterpart of the remote modem is installed.
OBJECT-TYPE    
  INTEGER  

rpsignalModem 1.3.6.1.4.1.760.1.1.2.1.9.6.1.2
The index of the local counterpart of the remote modem.
OBJECT-TYPE    
  INTEGER  

rpsignalPort 1.3.6.1.4.1.760.1.1.2.1.9.6.1.3
The index of the port at the remote modem that provides the signal.
OBJECT-TYPE    
  INTEGER  

rpsignalType 1.3.6.1.4.1.760.1.1.2.1.9.6.1.4
This entry indicates the signal type.
OBJECT-TYPE    
  INTEGER other(1), link(2), rts(3), dcd(4), dtr(5), dsr(6), c(7), i(8), fsync(9), ais(10), lay1(11), bond(12), laser-status(13), ta(14), ca(15), eclk(16), laser-tx(17), laser-temp(18), cr(20), rd(26), td(27)  

rpsignalStatus 1.3.6.1.4.1.760.1.1.2.1.9.6.1.5
This entry indicates the current status of the signal.
OBJECT-TYPE    
  INTEGER other(1), up(2), down(3), on(4), off(5), yes(6), no(7), ok(8), fail(9), active(10), traffic(11), space(12), mark(13), high(14), low(15), sync(16)  

mdmSpecifics 1.3.6.1.4.1.760.1.1.2.1.10
OBJECT IDENTIFIER    

portBackupDisabled 1.3.6.1.4.1.760.1.1.2.1.10
This trap will be sent when a modem in one of the slots leaves a backup status. The first port indicates the active data port, the second the inactive port. The rack number, index of the modem, and port number is sent along with this trap.
TRAP-TYPE    
  portPort  
  portPort  

mdm-oid 1.3.6.1.4.1.760.1.1.2.1.10.10000
OBJECT IDENTIFIER    

comp-id 1.3.6.1.4.1.760.1.1.2.1.10.10000.1
OBJECT IDENTIFIER    

rack-other 1.3.6.1.4.1.760.1.1.2.1.10.10000.1.1
OBJECT IDENTIFIER    

rack-10s-3hu 1.3.6.1.4.1.760.1.1.2.1.10.10000.1.2
OBJECT IDENTIFIER    

rack-12s-3hu 1.3.6.1.4.1.760.1.1.2.1.10.10000.1.3
OBJECT IDENTIFIER    

rack-10s-6hu 1.3.6.1.4.1.760.1.1.2.1.10.10000.1.4
OBJECT IDENTIFIER    

rack-6s-9s-6hu 1.3.6.1.4.1.760.1.1.2.1.10.10000.1.5
OBJECT IDENTIFIER    

device-stack-15s 1.3.6.1.4.1.760.1.1.2.1.10.10000.1.6
OBJECT IDENTIFIER    

rack-8s-4hu 1.3.6.1.4.1.760.1.1.2.1.10.10000.1.7
OBJECT IDENTIFIER    

rack-10s-2c-6hu 1.3.6.1.4.1.760.1.1.2.1.10.10000.1.8
OBJECT IDENTIFIER    

hs-rack-10s-3hu 1.3.6.1.4.1.760.1.1.2.1.10.10000.1.9
OBJECT IDENTIFIER    

rack-8s-2c-6hu 1.3.6.1.4.1.760.1.1.2.1.10.10000.1.10
OBJECT IDENTIFIER    

hs-rack-3s-1c-3hu 1.3.6.1.4.1.760.1.1.2.1.10.10000.1.11
OBJECT IDENTIFIER    

rack-1s-1c-1hu 1.3.6.1.4.1.760.1.1.2.1.10.10000.1.12
OBJECT IDENTIFIER    

rack-3s-1c-1hu 1.3.6.1.4.1.760.1.1.2.1.10.10000.1.13
OBJECT IDENTIFIER    

device-id 1.3.6.1.4.1.760.1.1.2.1.10.10000.2
OBJECT IDENTIFIER    

otherModem 1.3.6.1.4.1.760.1.1.2.1.10.10000.2.1
OBJECT IDENTIFIER    

cms-snmp-master 1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10001
OBJECT IDENTIFIER    

cms-slave 1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10002
OBJECT IDENTIFIER    

cms-intelligent-slave 1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10003
OBJECT IDENTIFIER    

rc-control 1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10004
OBJECT IDENTIFIER    

slot-id 1.3.6.1.4.1.760.1.1.2.1.10.10000.3
OBJECT IDENTIFIER    

modemSlot 1.3.6.1.4.1.760.1.1.2.1.10.10000.3.1
OBJECT IDENTIFIER    

mgmtSlot 1.3.6.1.4.1.760.1.1.2.1.10.10000.3.2
OBJECT IDENTIFIER    

modemAddr 1.3.6.1.4.1.760.1.1.2.1.10.10000.3.3
OBJECT IDENTIFIER    

mgmtAddr 1.3.6.1.4.1.760.1.1.2.1.10.10000.3.4
OBJECT IDENTIFIER    

wdmSlot 1.3.6.1.4.1.760.1.1.2.1.10.10000.3.5
OBJECT IDENTIFIER    

controlSlot 1.3.6.1.4.1.760.1.1.2.1.10.10000.3.6
OBJECT IDENTIFIER    

psupplySlot 1.3.6.1.4.1.760.1.1.2.1.10.10000.3.10
OBJECT IDENTIFIER    

port-id 1.3.6.1.4.1.760.1.1.2.1.10.10000.4
OBJECT IDENTIFIER    

otherPort 1.3.6.1.4.1.760.1.1.2.1.10.10000.4.1
OBJECT IDENTIFIER    

interfacePort 1.3.6.1.4.1.760.1.1.2.1.10.10000.4.2
OBJECT IDENTIFIER    

linePort 1.3.6.1.4.1.760.1.1.2.1.10.10000.4.3
OBJECT IDENTIFIER    

vt100mgmtPort 1.3.6.1.4.1.760.1.1.2.1.10.10000.4.4
OBJECT IDENTIFIER    

outbandmgmtPort 1.3.6.1.4.1.760.1.1.2.1.10.10000.4.5
OBJECT IDENTIFIER    

backupPort 1.3.6.1.4.1.760.1.1.2.1.10.10000.4.6
OBJECT IDENTIFIER    

rs485Port 1.3.6.1.4.1.760.1.1.2.1.10.10000.4.7
OBJECT IDENTIFIER    

psupply-id 1.3.6.1.4.1.760.1.1.2.1.10.10000.5
OBJECT IDENTIFIER    

ps-other 1.3.6.1.4.1.760.1.1.2.1.10.10000.5.1
OBJECT IDENTIFIER    

p-ac-x-5v-20a 1.3.6.1.4.1.760.1.1.2.1.10.10000.5.2
OBJECT IDENTIFIER    

p-ac-x-5v-30a 1.3.6.1.4.1.760.1.1.2.1.10.10000.5.3
OBJECT IDENTIFIER    

p-dc-48v-5v-18a 1.3.6.1.4.1.760.1.1.2.1.10.10000.5.4
OBJECT IDENTIFIER    

p-dc-24v-5v-15a 1.3.6.1.4.1.760.1.1.2.1.10.10000.5.5
OBJECT IDENTIFIER    

p-dc-48v-5v-30a 1.3.6.1.4.1.760.1.1.2.1.10.10000.5.6
OBJECT IDENTIFIER    

b-ac-x-5v-6a 1.3.6.1.4.1.760.1.1.2.1.10.10000.5.7
OBJECT IDENTIFIER    

b-dc-48v-5v-lc 1.3.6.1.4.1.760.1.1.2.1.10.10000.5.8
OBJECT IDENTIFIER    

b-dc-48v-5v-hc 1.3.6.1.4.1.760.1.1.2.1.10.10000.5.9
OBJECT IDENTIFIER    

b-dc-24v-5v-su 1.3.6.1.4.1.760.1.1.2.1.10.10000.5.10
OBJECT IDENTIFIER    

p-ac-x-3v-20a 1.3.6.1.4.1.760.1.1.2.1.10.10000.5.11
OBJECT IDENTIFIER    

p-dc-48v-5v-20a 1.3.6.1.4.1.760.1.1.2.1.10.10000.5.12
OBJECT IDENTIFIER    

p-dc-5v-3v-4a 1.3.6.1.4.1.760.1.1.2.1.10.10000.5.13
OBJECT IDENTIFIER    

p-dc-5v-5v-5a 1.3.6.1.4.1.760.1.1.2.1.10.10000.5.14
OBJECT IDENTIFIER    

psonoff-id 1.3.6.1.4.1.760.1.1.2.1.10.10000.6
OBJECT IDENTIFIER    

pS1-PS2-other 1.3.6.1.4.1.760.1.1.2.1.10.10000.6.1
OBJECT IDENTIFIER    

pS1-on-PS2-off 1.3.6.1.4.1.760.1.1.2.1.10.10000.6.2
OBJECT IDENTIFIER    

pS1-on-PS2-on 1.3.6.1.4.1.760.1.1.2.1.10.10000.6.3
OBJECT IDENTIFIER    

fanonoff-id 1.3.6.1.4.1.760.1.1.2.1.10.10000.7
OBJECT IDENTIFIER    

fAN1-FAN2-other 1.3.6.1.4.1.760.1.1.2.1.10.10000.7.1
OBJECT IDENTIFIER    

fAN1-off-FAN2-off 1.3.6.1.4.1.760.1.1.2.1.10.10000.7.2
OBJECT IDENTIFIER    

fAN1-on-FAN2-off 1.3.6.1.4.1.760.1.1.2.1.10.10000.7.3
OBJECT IDENTIFIER    

fAN1-off-FAN2-on 1.3.6.1.4.1.760.1.1.2.1.10.10000.7.4
OBJECT IDENTIFIER    

fAN1-on-FAN2-on 1.3.6.1.4.1.760.1.1.2.1.10.10000.7.5
OBJECT IDENTIFIER    

portBackupAvailable 1.3.6.1.4.1.760.1.1.2.1.11
This trap will be sent when a second link can be used as backup. The rack number, index of the modem, and port number is sent along with this trap.
TRAP-TYPE    
  portPort  

portBackupNotAvailable 1.3.6.1.4.1.760.1.1.2.1.12
This trap will be sent when there is no second link available as backup. The rack number, index of the modem, and port number is sent along with this trap.
TRAP-TYPE    
  portPort  

portDataPortChanged 1.3.6.1.4.1.760.1.1.2.1.13
This trap will be sent when the line port used for data transmission is changed. The first port indicates the active data port, the second the inactive port. The rack number, index of the modem, and port number is sent along with this trap.
TRAP-TYPE    
  portPort  
  portPort  

mdmMgmtIfGroup 1.3.6.1.4.1.760.1.1.2.1.20
OBJECT IDENTIFIER    

mdmIfType 1.3.6.1.4.1.760.1.1.2.1.20.1
This variable shows the agent's interface type.
OBJECT-TYPE    
  INTEGER other(1), v24(2), v35(4), x21(5), ethernet(6), missing(999)  

mdmIfProtocol 1.3.6.1.4.1.760.1.1.2.1.20.2
This variable shows the agent's protocol type.
OBJECT-TYPE    
  INTEGER other(1), slip(2), ppp-async(3), ppp-sync(4), ethernetII(5)  

mdmIfDataRate 1.3.6.1.4.1.760.1.1.2.1.20.3
This variable shows the agent's data rate in bps.
OBJECT-TYPE    
  INTEGER  

mdmIfDialEnable 1.3.6.1.4.1.760.1.1.2.1.20.4
This variable enables the initialization of a dial modem in case of alarm. The following variables (5 to 10) are active only if this variable is enabled.
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

mdmIfInitString 1.3.6.1.4.1.760.1.1.2.1.20.5
This variable defines an init string which is generated in case of alarm to configure an external Hayes compatible modem.
OBJECT-TYPE    
  DisplayString  

mdmIfDialString 1.3.6.1.4.1.760.1.1.2.1.20.6
This variable defines a modem command which is generated in case of alarm to dial-up a remote NMS station. If the dial string is not defined neither the init string nor the dial string is generated.
OBJECT-TYPE    
  DisplayString  

mdmIfSendTTL 1.3.6.1.4.1.760.1.1.2.1.20.7
This variable defines the TTL (time to live) in seconds. After that time the generated traps will be deleted from the buffer. If the value is '0' the traps will remain in the buffer.
OBJECT-TYPE    
  INTEGER  

mdmIfDialTimeout 1.3.6.1.4.1.760.1.1.2.1.20.8
This variable defines a dial timeout for the modem in seconds.
OBJECT-TYPE    
  INTEGER  

mdmIfRedialPause 1.3.6.1.4.1.760.1.1.2.1.20.9
This variable defines the duration of a redial pause in seconds.
OBJECT-TYPE    
  INTEGER  

mdmIfIdlePeriodBeforeDisconnect 1.3.6.1.4.1.760.1.1.2.1.20.10
This variable defines the period of time before disconnecting in seconds. If the value is '0' the modem will remain connected.
OBJECT-TYPE    
  INTEGER  

Defined Objects

RackEntry  
SEQUENCE    
  INTEGER as rackRack  
  INTEGER as rackType  
  DisplayString as rackDescription  
  INTEGER as rackModemSlots  
  INTEGER as rackModems  
  INTEGER as rackPowerSupplySlots  
  INTEGER as rackPowerSupplies  

ModemEntry  
SEQUENCE    
  INTEGER as mdmRack  
  INTEGER as mdmModem  
  DisplayString as mdmDescription  
  DisplayString as mdmUserName  
  INTEGER as mdmSelfTest  
  INTEGER as mdmSelfTestResult  
  INTEGER as mdmRemoteAccessStatus  
  INTEGER as mdmInterfacePorts  
  INTEGER as mdmLinePorts  

VerInfoEntry  
SEQUENCE    
  INTEGER as viRack  
  INTEGER as viModem  
  INTEGER as viType  
  DisplayString as viFirmwVer  
  DisplayString as viUnitRel  
  DisplayString as viArtNo  
  INTEGER as viFrontVer  
  DisplayString as viSerialNumber  

PortEntry  
SEQUENCE    
  INTEGER as portRack  
  INTEGER as portModem  
  INTEGER as portPort  
  INTEGER as portType  
  INTEGER as portInterfaceType  
  INTEGER as portConnector  
  INTEGER as portLoopMode  

PortSignalEntry  
SEQUENCE    
  INTEGER as psignalRack  
  INTEGER as psignalModem  
  INTEGER as psignalPort  
  INTEGER as psignalType  
  INTEGER as psignalStatus  
  INTEGER as psignalTrap  

BERTEntry  
SEQUENCE    
  INTEGER as bertRack  
  INTEGER as bertModem  
  INTEGER as bertPort  
  INTEGER as bertBERTest  
  INTEGER as bertStatus  
  Counter as bertRunTime  
  Counter as bertInErrorTime  
  Counter as bertErrorFreeTime  
  Counter as bertKbitsRecWrapped  
  Counter as bertKbitsReceived  
  Counter as bertErrors  
  Counter as bertSyncLosts  
  INTEGER as bertSyncStatus  
  DisplayString as bertBitErrorRate  

RemModemEntry  
SEQUENCE    
  INTEGER as rmdmRack  
  INTEGER as rmdmModem  
  DisplayString as rmdmDescription  
  DisplayString as rmdmUserName  
  INTEGER as rmdmSelfTest  
  INTEGER as rmdmSelfTestResult  
  INTEGER as rmdmRemoteAccessStatus  
  INTEGER as rmdmInterfacePorts  
  INTEGER as rmdmLinePorts  

RemVerInfoEntry  
SEQUENCE    
  INTEGER as rviRack  
  INTEGER as rviModem  
  INTEGER as rviType  
  DisplayString as rviFirmwVer  
  DisplayString as rviUnitRel  
  DisplayString as rviArtNo  
  INTEGER as rviFrontVer  
  DisplayString as rviSerialNumber  

RemPortEntry  
SEQUENCE    
  INTEGER as rportRack  
  INTEGER as rportModem  
  INTEGER as rportPort  
  INTEGER as rportType  
  INTEGER as rportInterfaceType  
  INTEGER as rportConnector  
  INTEGER as rportLoopMode  

RemPortSignalEntry  
SEQUENCE    
  INTEGER as rpsignalRack  
  INTEGER as rpsignalModem  
  INTEGER as rpsignalPort  
  INTEGER as rpsignalType  
  INTEGER as rpsignalStatus