
| SNMPv2-SMI | SNMPv2-TC |
| MODULE-IDENTITY | OBJECT-TYPE | Gauge32 |
| NOTIFICATION-TYPE | DisplayString | TruthValue |
| IpAddress | enterprises |
| phihong | 1.3.6.1.4.1.24852 | ||
| OBJECT IDENTIFIER | |||
| poeProduct | 1.3.6.1.4.1.24852.2 | ||
| OBJECT IDENTIFIER | |||
| poeProductsPart | 1.3.6.1.4.1.24852.2.1 | ||
| the POE controller Part. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| poeSystem | 1.3.6.1.4.1.24852.2.2 | ||
| OBJECT IDENTIFIER | |||
| poeSystemActionHubReset | 1.3.6.1.4.1.24852.2.2.1 | ||
| Reset the POE controller. | |||
| OBJECT-TYPE | |||
| INTEGER | ready(0), reset(1) | ||
| poeSystemActionHubRestoreFactoryDefault | 1.3.6.1.4.1.24852.2.2.2 | ||
| Restore Factory Default to flash. resetpassword means when users forget the password,they can use this entry, and all of the snmp module parameters will be set to default values. | |||
| OBJECT-TYPE | |||
| INTEGER | ready(0), restore(1) | ||
| poeSystemActionHubSaveConfiguration | 1.3.6.1.4.1.24852.2.2.3 | ||
| Save the POE parameters to flash | |||
| OBJECT-TYPE | |||
| INTEGER | ready(0), save(1) | ||
| poeSystemAllPortPowerEnable | 1.3.6.1.4.1.24852.2.2.4 | ||
| Enables power supply in all port. Setting this object at a value enable(2) enables power and detection mechanism for all port. Setting this object at a value disable(1) disables power for all port. | |||
| OBJECT-TYPE | |||
| INTEGER | ready(0), disable(1), enable(2) | ||
| poeSystemHWVersion | 1.3.6.1.4.1.24852.2.2.6 | ||
| System hardware version for the Main board | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| poeSystemNumberOfChannel | 1.3.6.1.4.1.24852.2.2.7 | ||
| Number of ports in the system | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| poeSystemProductPartNumber | 1.3.6.1.4.1.24852.2.2.8 | ||
| System Part Number for PowerHub | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| poeSystemFirmwareVersion | 1.3.6.1.4.1.24852.2.2.10 | ||
| System firmware version for the POE | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| poeSystemDescription | 1.3.6.1.4.1.24852.2.2.11 | ||
| System Description 10 characters | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..10) | ||
| poeSystemConsumptionPower | 1.3.6.1.4.1.24852.2.2.12 | ||
| Measured usage power expressed in Watts. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| poeSystemControlACPower | 1.3.6.1.4.1.24852.2.2.13 | ||
| describes the maximum available power in Watts to be supplied by the AC backup source to this device. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| poeSystemControlDCPower | 1.3.6.1.4.1.24852.2.2.14 | ||
| describes the maximum available power in Watts to be supplied by the DC backup source to this device. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| poeSystemControlBothPower | 1.3.6.1.4.1.24852.2.2.15 | ||
| describes the maximum available power in Watts to be supplied by Both AC and DC backup source to this device. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| poeSystemParameters | 1.3.6.1.4.1.24852.2.2.16 | ||
| 1st char:Knokoff enable,2nd char:AC Disconnect enable,3th char:Disable Power Management | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(3) | ||
| poeSystemSnmpVersion | 1.3.6.1.4.1.24852.2.2.17 | ||
| The software version for the SNMP device | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| poeSystemPerPortPowerEnable | 1.3.6.1.4.1.24852.2.2.18 | ||
| Enables power supply in all port. Setting this object at a value enable(2) enables power and detection mechanism for all port. Setting this object at a value disable(1) disables power for all port. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(48) | ||
| poeSystemStatus | 1.3.6.1.4.1.24852.2.2.19 | ||
| The status of the POE. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(0), overheat(1) | ||
| poePortTable | 1.3.6.1.4.1.24852.2.3 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PoePortEntry | |||
| poePortEntry | 1.3.6.1.4.1.24852.2.3.1 | ||
| port entry containing data regarding a particular port | |||
| OBJECT-TYPE | |||
| PoePortEntry | |||
| poePortIndex | 1.3.6.1.4.1.24852.2.3.1.1 | ||
| A unique value for each port. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..2147483647 | ||
| poePortPowerEnable | 1.3.6.1.4.1.24852.2.3.1.2 | ||
| Enables power supply on this port. Setting this object at a value enable(2) enables power and detection mechanism for this port. Setting this object at a value disable(1) disables power for this port. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), enable(2) | ||
| poePortControlMaxPower | 1.3.6.1.4.1.24852.2.3.1.3 | ||
| This command specifies the max power in [mWatts] to that port. IF you set this value it will take out this port from the auto mode. The value MUST be more then 0 | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| poePortDescription | 1.3.6.1.4.1.24852.2.3.1.6 | ||
| Port Description 10 characters | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..10) | ||
| poePortDetectionStatus | 1.3.6.1.4.1.24852.2.3.1.7 | ||
| Port Detection, show the detection status of each port | |||
| OBJECT-TYPE | |||
| INTEGER | off(0), discR(1), discC(2), class(3), rampUp(4), ramPOEown(5), sampleI(8), sampleV(9) | ||
| poePortPowerClassifications | 1.3.6.1.4.1.24852.2.3.1.8 | ||
| Port Power Classifications, show the classification of each port | |||
| OBJECT-TYPE | |||
| INTEGER | class0(1), class1(2), class2(3), class3(4), class4(5) | ||
| poePortPowerDetectionControl | 1.3.6.1.4.1.24852.2.3.1.9 | ||
| Port Power Detection Control, enable or disable the Power Limit for Management | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(1), enabled(2) | ||
| poePortPowerPriority | 1.3.6.1.4.1.24852.2.3.1.10 | ||
| Port Power Priority, show the priority of each port | |||
| OBJECT-TYPE | |||
| INTEGER | critical(1), high(2), low(3) | ||
| poePortPower | 1.3.6.1.4.1.24852.2.3.1.11 | ||
| Port Actual Power (in mWattes). | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| poePortVoltage | 1.3.6.1.4.1.24852.2.3.1.12 | ||
| Port Voltage (in dVoltage). | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| poePortCurrent | 1.3.6.1.4.1.24852.2.3.1.13 | ||
| Port Current (in mAmps). | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| poePortResistance | 1.3.6.1.4.1.24852.2.3.1.14 | ||
| Port Resistance (in ohms). | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| poePortFlags | 1.3.6.1.4.1.24852.2.3.1.15 | ||
| 1st char:classification(0-3),2nd char:Port bypass detection enable,3th char:Port bypass classifiation enable,4th cahr:Port bypass powerup enable,5th char:Port bypass sampling enable. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(5) | ||
| poePortBypassFlags | 1.3.6.1.4.1.24852.2.3.1.16 | ||
| 1st char:Port bypass detection enable,2nd char:Port bypass classifiation enable,3th cahr:Port bypass powerup enable,4th char:Port bypass sampling enable. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(4) | ||
| poePortUseClassificationforPowerLimit | 1.3.6.1.4.1.24852.2.3.1.17 | ||
| Use Port classification for power limit , enable or disable the Port classification for power limit. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(1), enabled(2) | ||
| poePortLegacyDetection | 1.3.6.1.4.1.24852.2.3.1.18 | ||
| Use Port legacy detection , enable or disable the Port legacy detection. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(1), enabled(2) | ||
| poeTrapsControlTable | 1.3.6.1.4.1.24852.2.4 | ||
| A table of objects that display and control the Traps on a PSM device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PoeTrapsControlEntry | |||
| poeTrapsControlEntry | 1.3.6.1.4.1.24852.2.4.1 | ||
| A set of objects that control the Trap events. | |||
| OBJECT-TYPE | |||
| PoeTrapsControlEntry | |||
| poeTrapsControlGroupIndex | 1.3.6.1.4.1.24852.2.4.1.1 | ||
| This variable uniquely identifies the group. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..65535 | ||
| poeTrapsControlEnable | 1.3.6.1.4.1.24852.2.4.1.2 | ||
| Enable Traps from Agent | |||
| OBJECT-TYPE | |||
| INTEGER | trapsDisabled(1), trapsEnabled(2) | ||
| poeTraps | 1.3.6.1.4.1.24852.2.5 | ||
| OBJECT IDENTIFIER | |||
| poePortHWFailTrap | 1.3.6.1.4.1.24852.2.5.1 | ||
| This trap indicate UV0v failure /UV0v Spike failure /Device A2d failure. | |||
| NOTIFICATION-TYPE | |||
| poeTrapsControlGroupIndex | |||
| poePortVoltage | |||
| poePortPeakOverCurrentTrap | 1.3.6.1.4.1.24852.2.5.2 | ||
| This trap indicate peak over current failure. | |||
| NOTIFICATION-TYPE | |||
| poeTrapsControlGroupIndex | |||
| poePortCurrent | |||
| poePortOverloadTrap | 1.3.6.1.4.1.24852.2.5.3 | ||
| This trap indicate overload failure. If you put at least 400mA on the output, you will see if your traps work | |||
| NOTIFICATION-TYPE | |||
| poeTrapsControlGroupIndex | |||
| poePortDetectionStatus | |||
| poePortDiscoveryFailTrap | 1.3.6.1.4.1.24852.2.5.4 | ||
| This trap indicate Discovery failure/ Discovery VA2 failure/Discovery RA2 failure/Sample Discovery A2d Failure. | |||
| NOTIFICATION-TYPE | |||
| poeTrapsControlGroupIndex | |||
| poePortVoltage | |||
| poePortClassificationFailTrap | 1.3.6.1.4.1.24852.2.5.5 | ||
| This trap indicate Class Violation failure/ Classification A2d failure. | |||
| NOTIFICATION-TYPE | |||
| poeTrapsControlGroupIndex | |||
| poePortVoltage | |||
| poePortDisconnectTrap | 1.3.6.1.4.1.24852.2.5.6 | ||
| This trap indicate port is disconnected. | |||
| NOTIFICATION-TYPE | |||
| poeTrapsControlGroupIndex | |||
| poePortDetectionStatus | |||
| poePortVoltageFailTrap | 1.3.6.1.4.1.24852.2.5.7 | ||
| This trap indicate if PSM Port is no voltage failure. | |||
| NOTIFICATION-TYPE | |||
| poeTrapsControlGroupIndex | |||
| poePortVoltage | |||
| poeSystemOverheatTrap | 1.3.6.1.4.1.24852.2.5.8 | ||
| This trap indicate if PSM is overheat. | |||
| NOTIFICATION-TYPE | |||
| poeTrapsControlGroupIndex | |||
| PoePortEntry | |||
| SEQUENCE | |||
| INTEGER as poePortIndex | |||
| INTEGER as poePortPowerEnable | |||
| INTEGER as poePortControlMaxPower | |||
| DisplayString as poePortDescription | |||
| INTEGER as poePortDetectionStatus | |||
| INTEGER as poePortPowerClassifications | |||
| INTEGER as poePortPowerDetectionControl | |||
| INTEGER as poePortPowerPriority | |||
| INTEGER as poePortPower | |||
| DisplayString as poePortVoltage | |||
| INTEGER as poePortCurrent | |||
| INTEGER as poePortResistance | |||
| DisplayString as poePortFlags | |||
| DisplayString as poePortBypassFlags | |||
| INTEGER as poePortUseClassificationforPowerLimit | |||
| INTEGER as poePortLegacyDetection | |||
| PoeTrapsControlEntry | |||
| SEQUENCE | |||
| INTEGER as poeTrapsControlGroupIndex | |||
| INTEGER as poeTrapsControlEnable | |||