PIM-MIB

File: PIM-MIB.mib (31909 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IPMROUTE-STD-MIB IF-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE experimental
NOTIFICATION-TYPE Integer32 IpAddress
TimeTicks RowStatus TruthValue
MODULE-COMPLIANCE OBJECT-GROUP NOTIFICATION-GROUP
ipMRouteGroup ipMRouteSource ipMRouteSourceMask
ipMRouteNextHopGroup ipMRouteNextHopSource ipMRouteNextHopSourceMask
ipMRouteNextHopIfIndex ipMRouteNextHopAddress InterfaceIndex

Defined Objects

pimMIB 1.3.6.1.3.61
The MIB module for management of PIM routers.
MODULE-IDENTITY    

pimMIBObjects 1.3.6.1.3.61.1
OBJECT IDENTIFIER    

pimTraps 1.3.6.1.3.61.1.0
OBJECT IDENTIFIER    

pimNeighborLoss 1.3.6.1.3.61.1.0.1
A pimNeighborLoss trap signifies the loss of an adjacency with a neighbor. This trap should be generated when the neighbor timer expires, and the router has no other neighbors on the same interface with a lower IP address than itself.
NOTIFICATION-TYPE    
  pimNeighborIfIndex  

pim 1.3.6.1.3.61.1.1
OBJECT IDENTIFIER    

pimJoinPruneInterval 1.3.6.1.3.61.1.1.1
The default interval at which periodic PIM-SM Join/Prune messages are to be sent.
OBJECT-TYPE    
  Integer32  

pimInterfaceTable 1.3.6.1.3.61.1.1.2
The (conceptual) table listing the router's PIM interfaces. IGMP and PIM are enabled on all interfaces listed in this table.
OBJECT-TYPE    
  SEQUENCE OF  
    PimInterfaceEntry

pimInterfaceEntry 1.3.6.1.3.61.1.1.2.1
An entry (conceptual row) in the pimInterfaceTable.
OBJECT-TYPE    
  PimInterfaceEntry  

pimInterfaceIfIndex 1.3.6.1.3.61.1.1.2.1.1
The ifIndex value of this PIM interface.
OBJECT-TYPE    
  InterfaceIndex  

pimInterfaceAddress 1.3.6.1.3.61.1.1.2.1.2
The IP address of the PIM interface.
OBJECT-TYPE    
  IpAddress  

pimInterfaceNetMask 1.3.6.1.3.61.1.1.2.1.3
The network mask for the IP address of the PIM interface.
OBJECT-TYPE    
  IpAddress  

pimInterfaceMode 1.3.6.1.3.61.1.1.2.1.4
The configured mode of this PIM interface. A value of sparseDense is only valid for PIMv1.
OBJECT-TYPE    
  INTEGER dense(1), sparse(2), sparseDense(3)  

pimInterfaceDR 1.3.6.1.3.61.1.1.2.1.5
The Designated Router on this PIM interface. For point-to- point interfaces, this object has the value 0.0.0.0.
OBJECT-TYPE    
  IpAddress  

pimInterfaceHelloInterval 1.3.6.1.3.61.1.1.2.1.6
The frequency at which PIM Hello messages are transmitted on this interface.
OBJECT-TYPE    
  Integer32  

pimInterfaceStatus 1.3.6.1.3.61.1.1.2.1.7
The status of this entry. Creating the entry enables PIM on the interface; destroying the entry disables PIM on the interface.
OBJECT-TYPE    
  RowStatus  

pimInterfaceJoinPruneInterval 1.3.6.1.3.61.1.1.2.1.8
The frequency at which PIM Join/Prune messages are transmitted on this PIM interface. The default value of this object is the pimJoinPruneInterval.
OBJECT-TYPE    
  Integer32  

pimInterfaceCBSRPreference 1.3.6.1.3.61.1.1.2.1.9
The preference value for the local interface as a candidate bootstrap router. The value of -1 is used to indicate that the local interface is not a candidate BSR interface.
OBJECT-TYPE    
  Integer32 -1..255  

pimNeighborTable 1.3.6.1.3.61.1.1.3
The (conceptual) table listing the router's PIM neighbors.
OBJECT-TYPE    
  SEQUENCE OF  
    PimNeighborEntry

pimNeighborEntry 1.3.6.1.3.61.1.1.3.1
An entry (conceptual row) in the pimNeighborTable.
OBJECT-TYPE    
  PimNeighborEntry  

pimNeighborAddress 1.3.6.1.3.61.1.1.3.1.1
The IP address of the PIM neighbor for which this entry contains information.
OBJECT-TYPE    
  IpAddress  

pimNeighborIfIndex 1.3.6.1.3.61.1.1.3.1.2
The value of ifIndex for the interface used to reach this PIM neighbor.
OBJECT-TYPE    
  InterfaceIndex  

pimNeighborUpTime 1.3.6.1.3.61.1.1.3.1.3
The time since this PIM neighbor (last) became a neighbor of the local router.
OBJECT-TYPE    
  TimeTicks  

pimNeighborExpiryTime 1.3.6.1.3.61.1.1.3.1.4
The minimum time remaining before this PIM neighbor will be aged out.
OBJECT-TYPE    
  TimeTicks  

pimNeighborMode 1.3.6.1.3.61.1.1.3.1.5
The active PIM mode of this neighbor. This object is deprecated for PIMv2 routers since all neighbors on the interface must be either dense or sparse as determined by the protocol running on the interface.
OBJECT-TYPE    
  INTEGER dense(1), sparse(2)  

pimIpMRouteTable 1.3.6.1.3.61.1.1.4
The (conceptual) table listing PIM-specific information on a subset of the rows of the ipMRouteTable defined in the IP Multicast MIB.
OBJECT-TYPE    
  SEQUENCE OF  
    PimIpMRouteEntry

pimIpMRouteEntry 1.3.6.1.3.61.1.1.4.1
An entry (conceptual row) in the pimIpMRouteTable. There is one entry per entry in the ipMRouteTable whose incoming interface is running PIM.
OBJECT-TYPE    
  PimIpMRouteEntry  

pimIpMRouteUpstreamAssertTimer 1.3.6.1.3.61.1.1.4.1.1
The time remaining before the router changes its upstream neighbor back to its RPF neighbor. This timer is called the Assert timer in the PIM Sparse and Dense mode specification. A value of 0 indicates that no Assert has changed the upstream neighbor away from the RPF neighbor.
OBJECT-TYPE    
  TimeTicks  

pimIpMRouteAssertMetric 1.3.6.1.3.61.1.1.4.1.2
The metric advertised by the assert winner on the upstream interface, or 0 if no such assert is in received.
OBJECT-TYPE    
  Integer32  

pimIpMRouteAssertMetricPref 1.3.6.1.3.61.1.1.4.1.3
The preference advertised by the assert winner on the upstream interface, or 0 if no such assert is in effect.
OBJECT-TYPE    
  Integer32  

pimIpMRouteAssertRPTBit 1.3.6.1.3.61.1.1.4.1.4
The value of the RPT-bit advertised by the assert winner on the upstream interface, or false if no such assert is in effect.
OBJECT-TYPE    
  TruthValue  

pimIpMRouteFlags 1.3.6.1.3.61.1.1.4.1.5
This object describes PIM-specific flags related to a multicast state entry. See the PIM Sparse Mode specification for the meaning of the RPT and SPT bits.
OBJECT-TYPE    
  BITS rpt(0), spt(1)  

pimRPTable 1.3.6.1.3.61.1.1.5
The (conceptual) table listing PIM version 1 information for the Rendezvous Points (RPs) for IP multicast groups. This table is deprecated since its function is replaced by the pimRPSetTable for PIM version 2.
OBJECT-TYPE    
  SEQUENCE OF  
    PimRPEntry

pimRPEntry 1.3.6.1.3.61.1.1.5.1
An entry (conceptual row) in the pimRPTable. There is one entry per RP address for each IP multicast group.
OBJECT-TYPE    
  PimRPEntry  

pimRPGroupAddress 1.3.6.1.3.61.1.1.5.1.1
The IP multicast group address for which this entry contains information about an RP.
OBJECT-TYPE    
  IpAddress  

pimRPAddress 1.3.6.1.3.61.1.1.5.1.2
The unicast address of the RP.
OBJECT-TYPE    
  IpAddress  

pimRPState 1.3.6.1.3.61.1.1.5.1.3
The state of the RP.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

pimRPStateTimer 1.3.6.1.3.61.1.1.5.1.4
The minimum time remaining before the next state change. When pimRPState is up, this is the minimum time which must expire until it can be declared down. When pimRPState is down, this is the time until it will be declared up (in order to retry).
OBJECT-TYPE    
  TimeTicks  

pimRPLastChange 1.3.6.1.3.61.1.1.5.1.5
The value of sysUpTime at the time when the corresponding instance of pimRPState last changed its value.
OBJECT-TYPE    
  TimeTicks  

pimRPRowStatus 1.3.6.1.3.61.1.1.5.1.6
The status of this row, by which new entries may be created, or old entries deleted from this table.
OBJECT-TYPE    
  RowStatus  

pimRPSetTable 1.3.6.1.3.61.1.1.6
The (conceptual) table listing PIM information for candidate Rendezvous Points (RPs) for IP multicast groups. When the local router is the BSR, this information is obtained from received Candidate-RP-Advertisements. When the local router is not the BSR, this information is obtained from received RP-Set messages.
OBJECT-TYPE    
  SEQUENCE OF  
    PimRPSetEntry

pimRPSetEntry 1.3.6.1.3.61.1.1.6.1
An entry (conceptual row) in the pimRPSetTable.
OBJECT-TYPE    
  PimRPSetEntry  

pimRPSetGroupAddress 1.3.6.1.3.61.1.1.6.1.1
The IP multicast group address which, when combined with pimRPSetGroupMask, gives the group prefix for which this entry contains information about the Candidate-RP.
OBJECT-TYPE    
  IpAddress  

pimRPSetGroupMask 1.3.6.1.3.61.1.1.6.1.2
The multicast group address mask which, when combined with pimRPSetGroupAddress, gives the group prefix for which this entry contains information about the Candidate-RP.
OBJECT-TYPE    
  IpAddress  

pimRPSetAddress 1.3.6.1.3.61.1.1.6.1.3
The IP address of the Candidate-RP.
OBJECT-TYPE    
  IpAddress  

pimRPSetHoldTime 1.3.6.1.3.61.1.1.6.1.4
The holdtime of a Candidate-RP. If the local router is not the BSR, this value is 0.
OBJECT-TYPE    
  Integer32 0..255  

pimRPSetExpiryTime 1.3.6.1.3.61.1.1.6.1.5
The minimum time remaining before the Candidate-RP will be declared down. If the local router is not the BSR, this value is 0.
OBJECT-TYPE    
  TimeTicks  

pimRPSetComponent 1.3.6.1.3.61.1.1.6.1.6
A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value.
OBJECT-TYPE    
  Integer32 1..255  

pimIpMRouteNextHopTable 1.3.6.1.3.61.1.1.7
The (conceptual) table listing PIM-specific information on a subset of the rows of the ipMRouteNextHopTable defined in the IP Multicast MIB.
OBJECT-TYPE    
  SEQUENCE OF  
    PimIpMRouteNextHopEntry

pimIpMRouteNextHopEntry 1.3.6.1.3.61.1.1.7.1
An entry (conceptual row) in the pimIpMRouteNextHopTable. There is one entry per entry in the ipMRouteNextHopTable whose interface is running PIM and whose ipMRouteNextHopState is pruned(1).
OBJECT-TYPE    
  PimIpMRouteNextHopEntry  

pimIpMRouteNextHopPruneReason 1.3.6.1.3.61.1.1.7.1.2
This object indicates why the downstream interface was pruned, whether in response to a PIM prune message or due to PIM Assert processing.
OBJECT-TYPE    
  INTEGER other(1), prune(2), assert(3)  

pimCandidateRPTable 1.3.6.1.3.61.1.1.11
The (conceptual) table listing the IP multicast groups for which the local router is to advertise itself as a Candidate-RP when the value of pimComponentCRPHoldTime is non-zero. If this table is empty, then the local router will advertise itself as a Candidate-RP for all groups (providing the value of pimComponentCRPHoldTime is non- zero).
OBJECT-TYPE    
  SEQUENCE OF  
    PimCandidateRPEntry

pimCandidateRPEntry 1.3.6.1.3.61.1.1.11.1
An entry (conceptual row) in the pimCandidateRPTable.
OBJECT-TYPE    
  PimCandidateRPEntry  

pimCandidateRPGroupAddress 1.3.6.1.3.61.1.1.11.1.1
The IP multicast group address which, when combined with pimCandidateRPGroupMask, identifies a group prefix for which the local router will advertise itself as a Candidate-RP.
OBJECT-TYPE    
  IpAddress  

pimCandidateRPGroupMask 1.3.6.1.3.61.1.1.11.1.2
The multicast group address mask which, when combined with pimCandidateRPGroupMask, identifies a group prefix for which the local router will advertise itself as a Candidate-RP.
OBJECT-TYPE    
  IpAddress  

pimCandidateRPAddress 1.3.6.1.3.61.1.1.11.1.3
The (unicast) address of the interface which will be advertised as a Candidate-RP.
OBJECT-TYPE    
  IpAddress  

pimCandidateRPRowStatus 1.3.6.1.3.61.1.1.11.1.4
The status of this row, by which new entries may be created, or old entries deleted from this table.
OBJECT-TYPE    
  RowStatus  

pimComponentTable 1.3.6.1.3.61.1.1.12
The (conceptual) table containing objects specific to a PIM domain. One row exists for each domain to which the router is connected. A PIM-SM domain is defined as an area of the network over which Bootstrap messages are forwarded. Typically, a PIM-SM router will be a member of exactly one domain. This table also supports, however, routers which may form a border between two PIM-SM domains and do not forward Bootstrap messages between them.
OBJECT-TYPE    
  SEQUENCE OF  
    PimComponentEntry

pimComponentEntry 1.3.6.1.3.61.1.1.12.1
An entry (conceptual row) in the pimComponentTable.
OBJECT-TYPE    
  PimComponentEntry  

pimComponentIndex 1.3.6.1.3.61.1.1.12.1.1
A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value. Routers that only support membership in a single PIM-SM domain should use a pimComponentIndex value of 1.
OBJECT-TYPE    
  Integer32 1..255  

pimComponentBSRAddress 1.3.6.1.3.61.1.1.12.1.2
The IP address of the bootstrap router (BSR) for the local PIM region.
OBJECT-TYPE    
  IpAddress  

pimComponentBSRExpiryTime 1.3.6.1.3.61.1.1.12.1.3
The minimum time remaining before the bootstrap router in the local domain will be declared down. For candidate BSRs, this is the time until the component sends an RP-Set message. For other routers, this is the time until it may accept an RP-Set message from a lower candidate BSR.
OBJECT-TYPE    
  TimeTicks  

pimComponentCRPHoldTime 1.3.6.1.3.61.1.1.12.1.4
The holdtime of the component when it is a candidate RP in the local domain. The value of 0 is used to indicate that the local system is not a Candidate-RP.
OBJECT-TYPE    
  Integer32 0..255  

pimComponentStatus 1.3.6.1.3.61.1.1.12.1.5
The status of this entry. Creating the entry creates another protocol instance; destroying the entry disables a protocol instance.
OBJECT-TYPE    
  RowStatus  

pimMIBConformance 1.3.6.1.3.61.2
OBJECT IDENTIFIER    

pimMIBCompliances 1.3.6.1.3.61.2.1
OBJECT IDENTIFIER    

pimV1MIBCompliance 1.3.6.1.3.61.2.1.1
The compliance statement for routers running PIMv1 and implementing the PIM MIB.
MODULE-COMPLIANCE    

pimSparseV2MIBCompliance 1.3.6.1.3.61.2.1.2
The compliance statement for routers running PIM Sparse Mode and implementing the PIM MIB.
MODULE-COMPLIANCE    

pimDenseV2MIBCompliance 1.3.6.1.3.61.2.1.3
The compliance statement for routers running PIM Dense Mode and implementing the PIM MIB.
MODULE-COMPLIANCE    

pimMIBGroups 1.3.6.1.3.61.2.2
OBJECT IDENTIFIER    

pimNotificationGroup 1.3.6.1.3.61.2.2.1
A collection of notifications for signaling important PIM events.
NOTIFICATION-GROUP    

pimV2MIBGroup 1.3.6.1.3.61.2.2.2
A collection of objects to support management of PIM Sparse Mode (version 2) routers.
OBJECT-GROUP    

pimV2CandidateRPMIBGroup 1.3.6.1.3.61.2.2.3
A collection of objects to support configuration of which groups a router is to advertise itself as a Candidate-RP.
OBJECT-GROUP    

pimV1MIBGroup 1.3.6.1.3.61.2.2.4
A collection of objects to support management of PIM (version 1) routers.
OBJECT-GROUP    

pimDenseV2MIBGroup 1.3.6.1.3.61.2.2.5
A collection of objects to support management of PIM Dense Mode (version 2) routers.
OBJECT-GROUP    

pimNextHopGroup 1.3.6.1.3.61.2.2.6
A collection of optional objects to provide per-next hop information for diagnostic purposes. Supporting this group may add a large number of instances to a tree walk, but the information in this group can be extremely useful in tracking down multicast connectivity problems.
OBJECT-GROUP    

pimAssertGroup 1.3.6.1.3.61.2.2.7
A collection of optional objects to provide extra information about the assert election process. There is no protocol reason to keep such information, but some implementations may already keep this information and make it available. These objects can also be very useful in debugging connectivity or duplicate packet problems, especially if the assert winner does not support the PIM and IP Multicast MIBs.
OBJECT-GROUP    

Defined Objects

PimInterfaceEntry  
SEQUENCE    
  InterfaceIndex as pimInterfaceIfIndex  
  IpAddress as pimInterfaceAddress  
  IpAddress as pimInterfaceNetMask  
  INTEGER as pimInterfaceMode  
  IpAddress as pimInterfaceDR  
  Integer32 as pimInterfaceHelloInterval  
  RowStatus as pimInterfaceStatus  
  Integer32 as pimInterfaceJoinPruneInterval  
  Integer32 as pimInterfaceCBSRPreference  

PimNeighborEntry  
SEQUENCE    
  IpAddress as pimNeighborAddress  
  InterfaceIndex as pimNeighborIfIndex  
  TimeTicks as pimNeighborUpTime  
  TimeTicks as pimNeighborExpiryTime  
  INTEGER as pimNeighborMode  

PimIpMRouteEntry  
SEQUENCE    
  TimeTicks as pimIpMRouteUpstreamAssertTimer  
  Integer32 as pimIpMRouteAssertMetric  
  Integer32 as pimIpMRouteAssertMetricPref  
  TruthValue as pimIpMRouteAssertRPTBit  
  BITS as pimIpMRouteFlags  

PimIpMRouteNextHopEntry  
SEQUENCE    
  INTEGER as pimIpMRouteNextHopPruneReason  

PimRPEntry  
SEQUENCE    
  IpAddress as pimRPGroupAddress  
  IpAddress as pimRPAddress  
  INTEGER as pimRPState  
  TimeTicks as pimRPStateTimer  
  TimeTicks as pimRPLastChange  
  RowStatus as pimRPRowStatus  

PimRPSetEntry  
SEQUENCE    
  IpAddress as pimRPSetGroupAddress  
  IpAddress as pimRPSetGroupMask  
  IpAddress as pimRPSetAddress  
  Integer32 as pimRPSetHoldTime  
  TimeTicks as pimRPSetExpiryTime  
  Integer32 as pimRPSetComponent  

PimCandidateRPEntry  
SEQUENCE    
  IpAddress as pimCandidateRPGroupAddress  
  IpAddress as pimCandidateRPGroupMask  
  IpAddress as pimCandidateRPAddress  
  RowStatus as pimCandidateRPRowStatus  

PimComponentEntry  
SEQUENCE    
  Integer32 as pimComponentIndex  
  IpAddress as pimComponentBSRAddress  
  TimeTicks as pimComponentBSRExpiryTime  
  Integer32 as pimComponentCRPHoldTime  
  RowStatus as pimComponentStatus