PNNI-MIB

File: PNNI-MIB.mib (203621 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC IF-MIB
ATM-TC-MIB SNMPv2-CONF

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Gauge32 Integer32 enterprises
Unsigned32 zeroDotZero TEXTUAL-CONVENTION
RowStatus DisplayString TimeStamp
TruthValue InterfaceIndex ifIndex
AtmTrafficDescrParamIndex MODULE-COMPLIANCE OBJECT-GROUP

Defined Objects

atmForum 1.3.6.1.4.1.353
OBJECT IDENTIFIER    

atmForumNetworkManagement 1.3.6.1.4.1.353.5
OBJECT IDENTIFIER    

atmfPnni 1.3.6.1.4.1.353.5.4
OBJECT IDENTIFIER    

pnniMIB 1.3.6.1.4.1.353.5.4.1
The MIB module for managing ATM Forum PNNI routing.
MODULE-IDENTITY    

pnniMIBObjects 1.3.6.1.4.1.353.5.4.1.1
OBJECT IDENTIFIER    

pnniBaseGroup 1.3.6.1.4.1.353.5.4.1.1.1
OBJECT IDENTIFIER    

pnniHighestVersion 1.3.6.1.4.1.353.5.4.1.1.1.1
The highest version of the PNNI protocol that the software in this switching system is capable of executing.
OBJECT-TYPE    
  PnniVersion  

pnniLowestVersion 1.3.6.1.4.1.353.5.4.1.1.1.2
The lowest version of the PNNI Protocol that the software in this switching system is capable of executing.
OBJECT-TYPE    
  PnniVersion  

pnniDtlCountOriginator 1.3.6.1.4.1.353.5.4.1.1.1.3
The total number of DTL stacks that this switching system has originated as the DTLOriginator and placed into signalling messages. This includes the initial DTL stacks computed by this system as well as any alternate route (second, third choice etc.) DTL stacks computed by this switching system in response to crankbacks.
OBJECT-TYPE    
  Counter32  

pnniDtlCountBorder 1.3.6.1.4.1.353.5.4.1.1.1.4
The number of partial DTL stacks that this switching system has added into signalling messages as an entry border node. This includes the initial partial DTL stacks computed by this system as well as any alternate route (second, third choice etc.) partial DTL stacks computed by this switching system in response to crankbacks.
OBJECT-TYPE    
  Counter32  

pnniCrankbackCountOriginator 1.3.6.1.4.1.353.5.4.1.1.1.5
The count of the total number of connection setup messages including DTL stacks originated by this switching system that have cranked back to this switching system at all levels of the hierarchy.
OBJECT-TYPE    
  Counter32  

pnniCrankbackCountBorder 1.3.6.1.4.1.353.5.4.1.1.1.6
The count of the total number of connection setup messages including DTLs added by this switching system as an entry border node that have cranked back to this switching system at all levels of the hierarchy. This count does not include Crankbacks for which this switching system was not the crankback destination, only those crankbacks that were directed to this switching system are counted here.
OBJECT-TYPE    
  Counter32  

pnniAltRouteCountOriginator 1.3.6.1.4.1.353.5.4.1.1.1.7
The total number of alternate DTL stacks that this switching system has computed and placed into signalling messages as the DTLOriginator.
OBJECT-TYPE    
  Counter32  

pnniAltRouteCountBorder 1.3.6.1.4.1.353.5.4.1.1.1.8
The total number of alternate partial DTL stacks that this switching system has computed and placed into signalling messages as an entry border node.
OBJECT-TYPE    
  Counter32  

pnniRouteFailCountOriginator 1.3.6.1.4.1.353.5.4.1.1.1.9
The total number of times where the switching system failed to compute a viable DTL stack as the DTLOriginator for some call. It indicates the number of times a call was cleared from this switching system due to originator routing failure.
OBJECT-TYPE    
  Counter32  

pnniRouteFailCountBorder 1.3.6.1.4.1.353.5.4.1.1.1.10
The total number of times where the switching system failed to compute a viable partial DTL stack as an entry border node for some call. It indicates the number of times a call was either cleared or cranked back from this switching system due to border routing failure.
OBJECT-TYPE    
  Counter32  

pnniRouteFailUnreachableOriginator 1.3.6.1.4.1.353.5.4.1.1.1.11
The total number of times where the switching system failed to compute a viable DTL stack as the DTLOriginator because the destination was unreachable, i.e., those calls that are cleared with cause #2 `specified transit network unreachable' or cause #3 `destination unreachable' in the cause IE.
OBJECT-TYPE    
  Counter32  

pnniRouteFailUnreachableBorder 1.3.6.1.4.1.353.5.4.1.1.1.12
The total number of times where the switching system failed to compute a viable partial DTL stack as an entry border node because the target of the path calculation was unreachable, i.e., those calls that are cleared or cranked back with cause #2 `specified transit network unreachable' or cause #3 `destination unreachable' in the cause IE.
OBJECT-TYPE    
  Counter32  

pnniNodeTable 1.3.6.1.4.1.353.5.4.1.1.2
The pnniNodeTable collects attributes that affect the operation of a PNNI logical node. There is a single row in this table for each PNNI peer group that the managed system is expected or eligible to become a member of.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniNodeEntry

pnniNodeEntry 1.3.6.1.4.1.353.5.4.1.1.2.1
An entry in the table, containing information about a PNNI logical node in this switching system.
OBJECT-TYPE    
  PnniNodeEntry  

pnniNodeIndex 1.3.6.1.4.1.353.5.4.1.1.2.1.1
A value assigned to a node in this switching system that uniquely identifies it in the MIB.
OBJECT-TYPE    
  PnniNodeIndex  

pnniNodeLevel 1.3.6.1.4.1.353.5.4.1.1.2.1.2
The level of PNNI hierarchy at which this node exists. This attribute is used to determine the default node ID and the default peer group ID for this node. This object may only be written when pnniNodeAdminStatus has the value down.
OBJECT-TYPE    
  PnniLevel  

pnniNodeId 1.3.6.1.4.1.353.5.4.1.1.2.1.3
The value the switching system is using to represent itself as this node. This object may only be written when pnniNodeAdminStatus has the value down. If pnniNodeLowest is true, then the default node ID takes the form defined in Section 5.3.3 for lowest level nodes, with the first octet equal to pnniNodeLevel, the second octet equal to 160, and the last 20 octets equal to pnniNodeAtmAddress. If pnniNodeLowest is false, then the default node ID takes the form defined in Section 5.3.3 for logical group nodes, with the first octet equal to pnniNodeLevel, the next fourteen octets equal to the value of pnniNodePeerGroupId for the child node whose election as PGL causes this LGN to be instantiated, the next six octets equal to the ESI of pnniNodeAtmAddress, and the last octet equal to zero.
OBJECT-TYPE    
  PnniNodeId  

pnniNodeLowest 1.3.6.1.4.1.353.5.4.1.1.2.1.4
Indicates whether this node acts as a lowest level node or whether this node is a logical group node that becomes active when one of the other nodes in this switching system becomes a peer group leader. The value 'false' must not be used with nodes that are not PGL/LGN capable. This object may only be written when pnniNodeAdminStatus has the value down.
OBJECT-TYPE    
  TruthValue  

pnniNodeAdminStatus 1.3.6.1.4.1.353.5.4.1.1.2.1.5
Indicates whether the administrative status of the node is up (the node is allowed to become active) or down (the node is forced to be inactive). When pnniNodeAdminStatus is down, then pnniNodeOperStatus must also be down.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

pnniNodeOperStatus 1.3.6.1.4.1.353.5.4.1.1.2.1.6
Indicates whether the node is active or whether the node has yet to become operational. When the value is down, all state has been cleared from the node and the node is not communicating with any of its neighbor nodes.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

pnniNodeDomainName 1.3.6.1.4.1.353.5.4.1.1.2.1.7
The name of the PNNI routing domain in which this node participates. All lowest-level PNNI nodes with the same pnniNodeDomainName are presumed to be connected.
OBJECT-TYPE    
  DisplayString  

pnniNodeAtmAddress 1.3.6.1.4.1.353.5.4.1.1.2.1.8
This node's ATM End System Address. Remote systems wishing to exchange PNNI protocol packets with this node should direct packets or calls to this address. This attribute may only be written when pnniNodeAdminStatus has the value down.
OBJECT-TYPE    
  PnniAtmAddr  

pnniNodePeerGroupId 1.3.6.1.4.1.353.5.4.1.1.2.1.9
The Peer Group Identifier of the peer group that the given node is to become a member of. The default value of this attribute has the first octet equal to pnniNodeLevel, the next pnniNodeLevel bits equal to the pnniNodeLevel bits starting from the third octet of pnniNodeId, and the remainder padded with zeros. This object may only be written when pnniNodeAdminStatus has the value down.
OBJECT-TYPE    
  PnniPeerGroupId  

pnniNodeRestrictedTransit 1.3.6.1.4.1.353.5.4.1.1.2.1.10
Specifies whether the node is restricted to not allowing support of SVCs transiting this node. This attribute determines the setting of the restricted transit bit in the nodal information group originated by this node.
OBJECT-TYPE    
  TruthValue  

pnniNodeComplexRep 1.3.6.1.4.1.353.5.4.1.1.2.1.11
Specifies whether this node uses the complex node representation. A value of `true' indicates that the complex node representation is used, whereas a value of `false' indicates that the simple node representation is used. This attribute determines the setting of the nodal representation bit in the nodal information group originated by this node.
OBJECT-TYPE    
  TruthValue  

pnniNodeRestrictedBranching 1.3.6.1.4.1.353.5.4.1.1.2.1.12
Indicates whether the node is able to support additional point-to-multipoint branches. A value of 'false' indicates that additional branches can be supported, and a value of 'true' indicates that additional branches cannot be supported. This attribute reflects the setting of the restricted branching bit in the nodal information group originated by this node.
OBJECT-TYPE    
  TruthValue  

pnniNodeDatabaseOverload 1.3.6.1.4.1.353.5.4.1.1.2.1.13
Specifies whether the node is currently operating in topology database overload state. This attribute has the same value as the Non-transit for PGL Election bit in the nodal information group originated by this node.
OBJECT-TYPE    
  TruthValue  

pnniNodePtses 1.3.6.1.4.1.353.5.4.1.1.2.1.14
Gauges the total number of PTSEs currently in this node's topology database(s).
OBJECT-TYPE    
  Gauge32  

pnniNodeRowStatus 1.3.6.1.4.1.353.5.4.1.1.2.1.15
To create, delete, activate and de-activate a Node.
OBJECT-TYPE    
  RowStatus  

pnniNodePglTable 1.3.6.1.4.1.353.5.4.1.1.3
Peer group leader election information for a PNNI node in this switching system.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniNodePglEntry

pnniNodePglEntry 1.3.6.1.4.1.353.5.4.1.1.3.1
An entry in the table, containing PGL election information of a PNNI logical node in this switching system.
OBJECT-TYPE    
  PnniNodePglEntry  

pnniNodePglLeadershipPriority 1.3.6.1.4.1.353.5.4.1.1.3.1.1
The Leadership priority value this node should advertise in its nodal information group for the given peer group. Only the value zero can be used with nodes that are not PGL/LGN capable. If there is no configured parent node index or no corresponding entry in the pnniNodeTable, then the advertised leadership priority is zero regardless of this value.
OBJECT-TYPE    
  INTEGER 0..205  

pnniNodeCfgParentNodeIndex 1.3.6.1.4.1.353.5.4.1.1.3.1.2
The local node index used to identify the node that will represent this peer group at the next higher level of hierarchy, if this node becomes peer group leader. The value 0 indicates that there is no parent node.
OBJECT-TYPE    
  PnniNodeIndex  

pnniNodePglInitTime 1.3.6.1.4.1.353.5.4.1.1.3.1.3
The amount of time in seconds this node will delay advertising its choice of preferred PGL after having initialized operation and reached the full state with at least one neighbor in the peer group.
OBJECT-TYPE    
  Integer32  

pnniNodePglOverrideDelay 1.3.6.1.4.1.353.5.4.1.1.3.1.4
The amount of time in seconds a node will wait for itself to be declared the preferred PGL by unanimous agreement among its peers. In the absence of unanimous agreement this will be the amount of time that will pass before this node considers a two thirds majority as sufficient agreement to declare itself peer group leader, abandoning the attempt to get unanimous agreement.
OBJECT-TYPE    
  Integer32  

pnniNodePglReelectTime 1.3.6.1.4.1.353.5.4.1.1.3.1.5
The amount of time in seconds after losing connectivity to the current peer group leader, that this node will wait before re-starting the process of electing a new peer group leader.
OBJECT-TYPE    
  Integer32  

pnniNodePglState 1.3.6.1.4.1.353.5.4.1.1.3.1.6
Indicates the state that this node is in with respect to the Peer Group Leader election that takes place in the node's peer group. The values are enumerated in the Peer Group Leader State Machine.
OBJECT-TYPE    
  INTEGER starting(1), awaiting(2), awaitingFull(3), initialDelay(4), calculating(5), awaitUnanimity(6), operPgl(7), operNotPgl(8), hungElection(9), awaitReElection(10)  

pnniNodePreferredPgl 1.3.6.1.4.1.353.5.4.1.1.3.1.7
The Node ID of the node which the local node believes should be or become the peer group leader. This is also the value the local node is currently advertising in the `Preferred Peer Group Leader Node ID' field of its nodal information group within the given peer group. If a Preferred PGL has not been chosen, this attribute's value is set to (all) zero(s).
OBJECT-TYPE    
  PnniNodeId  

pnniNodePeerGroupLeader 1.3.6.1.4.1.353.5.4.1.1.3.1.8
The Node Identifier of the node which is currently operating as peer group leader of the peer group this node belongs to. If a PGL has not been elected, this attribute's value is set to (all) zero(s).
OBJECT-TYPE    
  PnniNodeId  

pnniNodePglTimeStamp 1.3.6.1.4.1.353.5.4.1.1.3.1.9
The time at which the current Peer Group Leader established itself.
OBJECT-TYPE    
  TimeStamp  

pnniNodeActiveParentNodeId 1.3.6.1.4.1.353.5.4.1.1.3.1.10
The Node Identifier value being used by the Peer Group Leader to represent this peer group at the next higher level of the hierarchy. If this node is at the highest level of the hierarchy or if no PGL has yet been elected the PNNI Protocol Entity sets the value of this attribute to (all) zero(s).
OBJECT-TYPE    
  PnniNodeId  

pnniNodeTimerTable 1.3.6.1.4.1.353.5.4.1.1.4
A table of initial PNNI timer values and significant change thresholds.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniNodeTimerEntry

pnniNodeTimerEntry 1.3.6.1.4.1.353.5.4.1.1.4.1
An entry in the table, containing initial PNNI timer values and significant change thresholds of a PNNI logical node in this switching system.
OBJECT-TYPE    
  PnniNodeTimerEntry  

pnniNodePtseHolddown 1.3.6.1.4.1.353.5.4.1.1.4.1.1
The initial value for the PTSE hold down timer that will be used by the given node to limit the rate at which it can re-originate PTSEs. It must be a positive non-zero number.
OBJECT-TYPE    
  Integer32  

pnniNodeHelloHolddown 1.3.6.1.4.1.353.5.4.1.1.4.1.2
The initial value for the Hello hold down timer that will be used by the given node to limit the rate at which it sends Hellos. It must be a positive non-zero number.
OBJECT-TYPE    
  Integer32  

pnniNodeHelloInterval 1.3.6.1.4.1.353.5.4.1.1.4.1.3
The initial value for the Hello Timer. In the absence of triggered Hellos, this node will send one Hello packet on each of its ports on this interval.
OBJECT-TYPE    
  Integer32  

pnniNodeHelloInactivityFactor 1.3.6.1.4.1.353.5.4.1.1.4.1.4
The value for the Hello Inactivity factor that this node will use to determine when a neighbor has gone down.
OBJECT-TYPE    
  Integer32  

pnniNodeHlinkInact 1.3.6.1.4.1.353.5.4.1.1.4.1.5
The amount of time a node will continue to advertise a horizontal (logical) link for which it has not received and processed a LGN Horizontal Link information group.
OBJECT-TYPE    
  Integer32  

pnniNodePtseRefreshInterval 1.3.6.1.4.1.353.5.4.1.1.4.1.6
The initial value for the Refresh timer that this node will use to drive (re-)origination of PTSEs in the absence of triggered updates.
OBJECT-TYPE    
  Integer32  

pnniNodePtseLifetimeFactor 1.3.6.1.4.1.353.5.4.1.1.4.1.7
The value for the lifetime multiplier, expressed as a percentage. The result of multiplying the pnniNodePtseRefreshInterval attribute value by this attribute value is used as the initial lifetime that this node places into self-originated PTSEs.
OBJECT-TYPE    
  INTEGER 101..1000  

pnniNodeRxmtInterval 1.3.6.1.4.1.353.5.4.1.1.4.1.8
The period between retransmissions of unacknowledged Database Summary packets, PTSE Request packets, and PTSPs.
OBJECT-TYPE    
  Integer32  

pnniNodePeerDelayedAckInterval 1.3.6.1.4.1.353.5.4.1.1.4.1.9
The minimum amount of time between transmissions of delayed PTSE acknowledgement packets.
OBJECT-TYPE    
  Integer32  

pnniNodeAvcrPm 1.3.6.1.4.1.353.5.4.1.1.4.1.10
The proportional multiplier used in the algorithms that determine significant change for AvCR parameters, expressed as a percentage.
OBJECT-TYPE    
  INTEGER 1..99  

pnniNodeAvcrMt 1.3.6.1.4.1.353.5.4.1.1.4.1.11
The minimum threshold used in the algorithms that determine significant change for AvCR parameters, expressed as a percentage.
OBJECT-TYPE    
  INTEGER 1..99  

pnniNodeCdvPm 1.3.6.1.4.1.353.5.4.1.1.4.1.12
The proportional multiplier used in the algorithms that determine significant change for CDV metrics, expressed as a percentage.
OBJECT-TYPE    
  INTEGER 1..99  

pnniNodeCtdPm 1.3.6.1.4.1.353.5.4.1.1.4.1.13
The proportional multiplier used in the algorithms that determine significant change for CTD metrics, expressed as a percentage.
OBJECT-TYPE    
  INTEGER 1..99  

pnniNodeSvccTable 1.3.6.1.4.1.353.5.4.1.1.5
A table of variables related to SVCC-based routing control channels.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniNodeSvccEntry

pnniNodeSvccEntry 1.3.6.1.4.1.353.5.4.1.1.5.1
An entry in the table, containing SVCC-based RCC variables of a PNNI logical node in this switching system.
OBJECT-TYPE    
  PnniNodeSvccEntry  

pnniNodeSvccInitTime 1.3.6.1.4.1.353.5.4.1.1.5.1.1
The amount of time this node will delay initiating establishment of an SVCC to a neighbor with a numerically lower ATM address, after determining that such an SVCC should be established.
OBJECT-TYPE    
  Integer32  

pnniNodeSvccRetryTime 1.3.6.1.4.1.353.5.4.1.1.5.1.2
The amount of time this node will delay after an apparently still necessary and viable SVCC-based RCC is unexpectedly torn down, before attempting to re-establish it.
OBJECT-TYPE    
  Integer32  

pnniNodeSvccCallingIntegrityTime 1.3.6.1.4.1.353.5.4.1.1.5.1.3
The amount of time this node will wait for an SVCC, which it has initiated establishment of as the calling party, to become fully established before giving up and tearing it down.
OBJECT-TYPE    
  Integer32  

pnniNodeSvccCalledIntegrityTime 1.3.6.1.4.1.353.5.4.1.1.5.1.4
The amount of time this node will wait for an SVCC, which it has decided to accept as the called party, to become fully established before giving up and tearing it down.
OBJECT-TYPE    
  Integer32  

pnniNodeSvccTrafficDescriptorIndex 1.3.6.1.4.1.353.5.4.1.1.5.1.5
An index into the atmTrafficDescrParamTable defined in RFC 1695. This traffic descriptor is used when establishing switched virtual channels for use as SVCC-based RCCs to/from PNNI logical group nodes.
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

pnniScopeMappingTable 1.3.6.1.4.1.353.5.4.1.1.6
The pnniScopeTable contains the mappings of membership and connection scope from organizational scope values (used at UNI interfaces) to PNNI scope (i.e. in terms of PNNI routing level indicators).
OBJECT-TYPE    
  SEQUENCE OF  
    PnniScopeMappingEntry

pnniScopeMappingEntry 1.3.6.1.4.1.353.5.4.1.1.6.1
An entry in the table, containing scope mapping information for a PNNI logical node in this switching system.
OBJECT-TYPE    
  PnniScopeMappingEntry  

pnniScopeLocalNetwork 1.3.6.1.4.1.353.5.4.1.1.6.1.1
The highest level of PNNI hierarchy (i.e. smallest PNNI routing level) that lies within the organizational scope value localNetwork(1).
OBJECT-TYPE    
  PnniLevel  

pnniScopeLocalNetworkPlusOne 1.3.6.1.4.1.353.5.4.1.1.6.1.2
The highest level of PNNI hierarchy (i.e. smallest PNNI routing level) that lies within the organizational scope value localNetworkPlusOne(2).
OBJECT-TYPE    
  PnniLevel  

pnniScopeLocalNetworkPlusTwo 1.3.6.1.4.1.353.5.4.1.1.6.1.3
The highest level of PNNI hierarchy (i.e. smallest PNNI routing level) that lies within the organizational scope value localNetworkPlusTwo(3).
OBJECT-TYPE    
  PnniLevel  

pnniScopeSiteMinusOne 1.3.6.1.4.1.353.5.4.1.1.6.1.4
The highest level of PNNI hierarchy (i.e. smallest PNNI routing level) that lies within the organizational scope value siteMinusOne(4).
OBJECT-TYPE    
  PnniLevel  

pnniScopeIntraSite 1.3.6.1.4.1.353.5.4.1.1.6.1.5
The highest level of PNNI hierarchy (i.e. smallest PNNI routing level) that lies within the organizational scope value intraSite(5).
OBJECT-TYPE    
  PnniLevel  

pnniScopeSitePlusOne 1.3.6.1.4.1.353.5.4.1.1.6.1.6
The highest level of PNNI hierarchy (i.e. smallest PNNI routing level) that lies within the organizational scope value sitePlusOne(6).
OBJECT-TYPE    
  PnniLevel  

pnniScopeOrganizationMinusOne 1.3.6.1.4.1.353.5.4.1.1.6.1.7
The highest level of PNNI hierarchy (i.e. smallest PNNI routing level) that lies within the organizational scope value organizationMinusOne(7).
OBJECT-TYPE    
  PnniLevel  

pnniScopeIntraOrganization 1.3.6.1.4.1.353.5.4.1.1.6.1.8
The highest level of PNNI hierarchy (i.e. smallest PNNI routing level) that lies within the organizational scope value intraOrganization(8).
OBJECT-TYPE    
  PnniLevel  

pnniScopeOrganizationPlusOne 1.3.6.1.4.1.353.5.4.1.1.6.1.9
The highest level of PNNI hierarchy (i.e. smallest PNNI routing level) that lies within the organizational scope value organizationPlusOne(9).
OBJECT-TYPE    
  PnniLevel  

pnniScopeCommunityMinusOne 1.3.6.1.4.1.353.5.4.1.1.6.1.10
The highest level of PNNI hierarchy (i.e. smallest PNNI routing level) that lies within the organizational scope value communityMinusOne(10).
OBJECT-TYPE    
  PnniLevel  

pnniScopeIntraCommunity 1.3.6.1.4.1.353.5.4.1.1.6.1.11
The highest level of PNNI hierarchy (i.e. smallest PNNI routing level) that lies within the organizational scope value intraCommunity(11).
OBJECT-TYPE    
  PnniLevel  

pnniScopeCommunityPlusOne 1.3.6.1.4.1.353.5.4.1.1.6.1.12
The highest level of PNNI hierarchy (i.e. smallest PNNI routing level) that lies within the organizational scope value communityPlusOne(12).
OBJECT-TYPE    
  PnniLevel  

pnniScopeRegional 1.3.6.1.4.1.353.5.4.1.1.6.1.13
The highest level of PNNI hierarchy (i.e. smallest PNNI routing level) that lies within the organizational scope value regional(13).
OBJECT-TYPE    
  PnniLevel  

pnniScopeInterRegional 1.3.6.1.4.1.353.5.4.1.1.6.1.14
The highest level of PNNI hierarchy (i.e. smallest PNNI routing level) that lies within the organizational scope value interRegional(14).
OBJECT-TYPE    
  PnniLevel  

pnniScopeGlobal 1.3.6.1.4.1.353.5.4.1.1.6.1.15
The highest level of PNNI hierarchy (i.e. smallest PNNI routing level) that lies within the organizational scope value global(15).
OBJECT-TYPE    
  PnniLevel  

pnniSummaryTable 1.3.6.1.4.1.353.5.4.1.1.7
A list of the summary address prefixes that may be advertised by the specified logical PNNI entity.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniSummaryEntry

pnniSummaryEntry 1.3.6.1.4.1.353.5.4.1.1.7.1
An entry in the table, containing summary address prefix information in this switching system.
OBJECT-TYPE    
  PnniSummaryEntry  

pnniSummaryAddress 1.3.6.1.4.1.353.5.4.1.1.7.1.1
The ATM End System Address prefix for the summary.
OBJECT-TYPE    
  AtmAddrPrefix  

pnniSummaryPrefixLength 1.3.6.1.4.1.353.5.4.1.1.7.1.2
The prefix length for the summary.
OBJECT-TYPE    
  PnniPrefixLength  

pnniSummaryType 1.3.6.1.4.1.353.5.4.1.1.7.1.3
The type (e.g. internal or exterior) of summary being described.
OBJECT-TYPE    
  INTEGER internal(1), exterior(2)  

pnniSummarySuppress 1.3.6.1.4.1.353.5.4.1.1.7.1.4
Determines what is done with addresses that are being summarized by the instance. The default value (e.g. false) will indicate that the summary should propagate into the peer group. Network Management will be able to set the value of this attribute to `suppress' (e.g. true), which suppresses the summary and any reachable addresses it summarizes from being advertised into the peer group.
OBJECT-TYPE    
  TruthValue  

pnniSummaryState 1.3.6.1.4.1.353.5.4.1.1.7.1.5
Indicates whether the summary is currently being advertised by the node within the local switching system into its peer group.
OBJECT-TYPE    
  INTEGER advertising(1), suppressing(2), inactive(3)  

pnniSummaryRowStatus 1.3.6.1.4.1.353.5.4.1.1.7.1.6
To create, delete, activate and de-activate a summary.
OBJECT-TYPE    
  RowStatus  

pnniIfTable 1.3.6.1.4.1.353.5.4.1.1.8
The pnniIfTable contains the attributes necessary to configure a physical interface on a switching system which is capable of being used for PNNI routing. Interfaces may represent physical connection points (i.e. copper/fiber connection points) or VPCs which have been configured for PNNI's use. Each interface is attached to a specific lowest-level node within the switching system. An ifIndex is used as the instance ID to uniquely identify the interface on the local switching system. This index has the same value as the ifIndex object defined in RFC 1573 for the same interface, since this table correlates with the ifTable in RFC 1573. One row in this table is created by the managed system for each row in the ifTable that has an ifType of atm(37) or atmLogical(80).
OBJECT-TYPE    
  SEQUENCE OF  
    PnniIfEntry

pnniIfEntry 1.3.6.1.4.1.353.5.4.1.1.8.1
An entry in the table, containing PNNI specific interface information in this switching system.
OBJECT-TYPE    
  PnniIfEntry  

pnniIfNodeIndex 1.3.6.1.4.1.353.5.4.1.1.8.1.1
Identifies the node within the switching system that the interface is directly attached to. The value zero is not a valid value.
OBJECT-TYPE    
  PnniNodeIndex 1..65535  

pnniIfPortId 1.3.6.1.4.1.353.5.4.1.1.8.1.2
The Port Identifier of the port as selected by the PNNI protocol entity for the given interface. This value has meaning only within the context of the node to which the port is attached. The distinguished value zero indicates that no PNNI Port Identifier has been assigned for this interface (for example, this value may be used when the interface is not running PNNI).
OBJECT-TYPE    
  PnniPortId  

pnniIfAggrToken 1.3.6.1.4.1.353.5.4.1.1.8.1.3
The configured aggregation token for this interface. The aggregation token controls what other links the link associated with this interface will be aggregated together with.
OBJECT-TYPE    
  PnniAggrToken  

pnniIfVPCapability 1.3.6.1.4.1.353.5.4.1.1.8.1.4
Indicates whether the interface is capable of having VPCs established within it or not. This object may only have the value `true' for physical ATM interfaces, i.e. those with an ifType of atm(37).
OBJECT-TYPE    
  TruthValue  

pnniIfAdmWeightCbr 1.3.6.1.4.1.353.5.4.1.1.8.1.5
The administrative weight of this interface for the constant bit rate service category.
OBJECT-TYPE    
  Unsigned32 1..16777215  

pnniIfAdmWeightRtVbr 1.3.6.1.4.1.353.5.4.1.1.8.1.6
The administrative weight of this interface for the real-time variable bit rate service category.
OBJECT-TYPE    
  Unsigned32 1..16777215  

pnniIfAdmWeightNrtVbr 1.3.6.1.4.1.353.5.4.1.1.8.1.7
The administrative weight of this interface for the non-real-time variable bit rate service category.
OBJECT-TYPE    
  Unsigned32 1..16777215  

pnniIfAdmWeightAbr 1.3.6.1.4.1.353.5.4.1.1.8.1.8
The administrative weight of this interface for the available bit rate service category.
OBJECT-TYPE    
  Unsigned32 1..16777215  

pnniIfAdmWeightUbr 1.3.6.1.4.1.353.5.4.1.1.8.1.9
The administrative weight of this interface for the unspecified bit rate service category.
OBJECT-TYPE    
  Unsigned32 1..16777215  

pnniIfRccServiceCategory 1.3.6.1.4.1.353.5.4.1.1.8.1.10
The service category used for the PNNI routing control channel (VCI=18) on this interface.
OBJECT-TYPE    
  ServiceCategory  

pnniIfRccTrafficDescrIndex 1.3.6.1.4.1.353.5.4.1.1.8.1.11
The traffic descriptor index referring to the entry in the atmTrafficDescrParamTable defined in RFC 1695 that specifies the traffic allocation for the PNNI routing control channel (VCI=18) on this interface.
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

pnniLinkTable 1.3.6.1.4.1.353.5.4.1.1.9
This table contains the attributes necessary to describe the operation of logical links attached to the local switching system and the relationship with the neighbor nodes on the other end of the links. Links are attached to a specific node within the switching system. A concatenation of the Node Index of the node within the local switching system and the port ID are used as the instance ID to uniquely identify the link. Links may represent horizontal links between lowest level neighboring peers, outside links, uplinks, or horizontal links to/from LGNs. The entire pnniLink object is read-only, reflecting the fact that this information is discovered dynamically by the PNNI protocol rather than configured.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniLinkEntry

pnniLinkEntry 1.3.6.1.4.1.353.5.4.1.1.9.1
An entry in the table, containing information about a link attached to a PNNI logical node in this switching system.
OBJECT-TYPE    
  PnniLinkEntry  

pnniLinkPortId 1.3.6.1.4.1.353.5.4.1.1.9.1.1
The Port Identifier of the link as selected by the local node. This value has meaning only within the context of the node to which the port is attached.
OBJECT-TYPE    
  PnniPortId  

pnniLinkType 1.3.6.1.4.1.353.5.4.1.1.9.1.2
Indicates the type of link being described.
OBJECT-TYPE    
  INTEGER unknown(1), lowestLevelHorizontalLink(2), horizontalLinkToFromLgn(3), lowestLevelOutsideLink(4), uplink(5), outsideLinkAndUplink(6)  

pnniLinkVersion 1.3.6.1.4.1.353.5.4.1.1.9.1.3
For horizontal and outside links between lowest-level nodes and for links of unknown type, this attribute indicates the version of PNNI routing protocol used to exchange information over this link. If communication with the neighbor node has not yet been established, then the Version is set to `unknown'. For uplinks (where the port ID is not also used for the underlying outside link) or links to/from LGNs, the Version is set to `unknown'.
OBJECT-TYPE    
  PnniVersion  

pnniLinkHelloState 1.3.6.1.4.1.353.5.4.1.1.9.1.4
For horizontal and outside links between lowest-level nodes and for links of unknown type, this attribute indicates the state of the Hello protocol exchange over this link. For links to/from LGNs, this attribute indicates the state of the corresponding LGN Horizontal Link Hello State Machine. For uplinks (where the port ID is not also used for the underlying outside link), this attribute is set to notApplicable.
OBJECT-TYPE    
  PnniHelloState  

pnniLinkRemoteNodeId 1.3.6.1.4.1.353.5.4.1.1.9.1.5
Indicates the node identifier of the remote (neighboring) node on the other end of the link. If the pnniLinkType is `outside link and uplink', this is the node identifier of the lowest-level neighbor node on the other end of the outside link. If the remote node ID is unknown or if the pnniLinkType is `uplink', this attribute is set to all zeros.
OBJECT-TYPE    
  PnniNodeId  

pnniLinkRemotePortId 1.3.6.1.4.1.353.5.4.1.1.9.1.6
Indicates the port identifier of the port at the remote end of the link as assigned by the remote node. If the pnniLinkType is `outside link and uplink', this is the port identifier assigned by the lowest-level neighbor node to identify the outside link. If the remote port ID is unknown or if the pnniLinkType is `uplink', this attribute is set to zero.
OBJECT-TYPE    
  PnniPortId  

pnniLinkDerivedAggrToken 1.3.6.1.4.1.353.5.4.1.1.9.1.7
Indicates the derived aggregation token value used on this link. For horizontal links between lowest-level nodes and when the link type is not yet known, this attribute takes the value of zero.
OBJECT-TYPE    
  PnniAggrToken  

pnniLinkUpnodeId 1.3.6.1.4.1.353.5.4.1.1.9.1.8
For outside links and uplinks, this attribute contains the Node Identifier of the upnode (the neighbor node's identity at the level of the common peer group). When the upnode has not yet been identified, this attribute is set to zero. For horizontal links or when the link type is not yet known, this attribute is set to zero.
OBJECT-TYPE    
  PnniNodeId  

pnniLinkUpnodeAtmAddress 1.3.6.1.4.1.353.5.4.1.1.9.1.9
For outside links and uplinks, this attribute contains the ATM End System Address used to establish connections to the upnode. When the upnode has not yet been identified, this attribute is set to zero. For horizontal links or when the link type is not yet known, this attribute is set to zero.
OBJECT-TYPE    
  PnniAtmAddr  

pnniLinkCommonPeerGroupId 1.3.6.1.4.1.353.5.4.1.1.9.1.10
For outside links and uplinks, this attribute contains the peer group identifier of the lowest level common Peer Group in the ancestry of the neighboring node and the node within the local switching system. The value of this attribute takes on a value determined by the Hello exchange of hierarchical information that occurs between the two lowest-level border nodes. When the common peer group has not yet been identified, this attribute is set to zero. For horizontal links or when the link type is not yet known, this attribute is set to all zeros.
OBJECT-TYPE    
  PnniPeerGroupId  

pnniLinkIfIndex 1.3.6.1.4.1.353.5.4.1.1.9.1.11
For horizontal and outside links between lowest-level nodes and for links of unknown type, this attribute identifies the interface to which the logical link corresponds. For all other cases, the value of this object is zero.
OBJECT-TYPE    
  InterfaceIndex  

pnniLinkSvccRccIndex 1.3.6.1.4.1.353.5.4.1.1.9.1.12
For horizontal links to/from LGNs, this attribute identifies the SVCC-based RCC used to exchange information with the neighboring peer logical group node. If the pnniLinkType is not `horizontal link to/from LGN', this attribute shall take the value of zero.
OBJECT-TYPE    
  PnniSvccRccIndex  

pnniLinkRcvHellos 1.3.6.1.4.1.353.5.4.1.1.9.1.13
For horizontal and outside links between lowest-level nodes and for links of unknown type, this attribute contains a count of the number of Hello Packets received over this link. If the pnniLinkType is `horizontal link to/from LGN' or `uplink', this attribute is set to zero.
OBJECT-TYPE    
  Counter32  

pnniLinkXmtHellos 1.3.6.1.4.1.353.5.4.1.1.9.1.14
For horizontal and outside links between lowest-level nodes and for links of unknown type, this attribute contains a count of the number of Hello Packets transmitted over this link. If the pnniLinkType is `horizontal link to/from LGN' or `uplink', this attribute is set to zero.
OBJECT-TYPE    
  Counter32  

pnniNbrPeerTable 1.3.6.1.4.1.353.5.4.1.1.10
The pnniNbrPeer Object contains all the attributes necessary to describe the relationship a node in this switching system has with a neighboring node within the same peer group. A concatenation of the Node Identifier of the node within the local switching system and the neighboring peer's Node Identifier is used to form the instance ID for this object. The entire pnniNbrPeer object is read-only, reflecting the fact that neighboring peers are discovered dynamically by the PNNI protocol rather than configured.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniNbrPeerEntry

pnniNbrPeerEntry 1.3.6.1.4.1.353.5.4.1.1.10.1
An entry in the table, containing information about this node's relationship with a neighboring peer node.
OBJECT-TYPE    
  PnniNbrPeerEntry  

pnniNbrPeerRemoteNodeId 1.3.6.1.4.1.353.5.4.1.1.10.1.1
The Node Identifier of the neighboring peer node.
OBJECT-TYPE    
  PnniNodeId  

pnniNbrPeerState 1.3.6.1.4.1.353.5.4.1.1.10.1.2
Indicates the state of this node's Neighboring Peer State Machine associated with pnniNbrPeerRemoteNodeId.
OBJECT-TYPE    
  INTEGER npdown(1), negotiating(2), exchanging(3), loading(4), full(5)  

pnniNbrPeerSvccRccIndex 1.3.6.1.4.1.353.5.4.1.1.10.1.3
Identifies the SVCC-based RCC being used to communicate with the neighboring peer if one exists. If both the local node and the neighboring peer node are lowest-level nodes, this attribute is set to zero.
OBJECT-TYPE    
  PnniSvccRccIndex  

pnniNbrPeerPortCount 1.3.6.1.4.1.353.5.4.1.1.10.1.4
A count of the total number of ports that connect to the neighboring peer. If the neighboring peer only communicates via an SVCC-based RCC, the value of this attribute is set to zero. Otherwise it is set to the total number of ports to the neighboring peer in the Hello state 2-WayInside.
OBJECT-TYPE    
  Gauge32  

pnniNbrPeerRcvDbSums 1.3.6.1.4.1.353.5.4.1.1.10.1.5
A count of the number of Database Summary Packets received from the neighboring peer.
OBJECT-TYPE    
  Counter32  

pnniNbrPeerXmtDbSums 1.3.6.1.4.1.353.5.4.1.1.10.1.6
A count of the number of Database Summary Packets transmitted to the neighboring peer.
OBJECT-TYPE    
  Counter32  

pnniNbrPeerRcvPtsps 1.3.6.1.4.1.353.5.4.1.1.10.1.7
A count of the number of PTSPs received from the neighboring peer.
OBJECT-TYPE    
  Counter32  

pnniNbrPeerXmtPtsps 1.3.6.1.4.1.353.5.4.1.1.10.1.8
A count of the number of PTSPs (re)transmitted to the neighboring peer.
OBJECT-TYPE    
  Counter32  

pnniNbrPeerRcvPtseReqs 1.3.6.1.4.1.353.5.4.1.1.10.1.9
A count of the number of PTSE Request packets received from the neighboring peer.
OBJECT-TYPE    
  Counter32  

pnniNbrPeerXmtPtseReqs 1.3.6.1.4.1.353.5.4.1.1.10.1.10
A count of the number of PTSE Request packets transmitted to the neighboring peer.
OBJECT-TYPE    
  Counter32  

pnniNbrPeerRcvPtseAcks 1.3.6.1.4.1.353.5.4.1.1.10.1.11
A count of the number of PTSE Ack packets received from the neighboring peer.
OBJECT-TYPE    
  Counter32  

pnniNbrPeerXmtPtseAcks 1.3.6.1.4.1.353.5.4.1.1.10.1.12
A count of the number of PTSE Ack packets transmitted to the neighboring peer.
OBJECT-TYPE    
  Counter32  

pnniNbrPeerPortTable 1.3.6.1.4.1.353.5.4.1.1.11
A table of all ports in Hello state 2-Way Inside to a given neighboring peer node. A concatenation of the Node Index of the node within the local switching system, the neighbor's Node Identifier and the Interface Index of the port being described forms the instance ID for this object. This object is only used for lowest-level nodes.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniNbrPeerPortEntry

pnniNbrPeerPortEntry 1.3.6.1.4.1.353.5.4.1.1.11.1
An entry in the table, containing information about a port in the Hello state 2-Way Inside from a PNNI logical node in this switching system to a neighboring peer node.
OBJECT-TYPE    
  PnniNbrPeerPortEntry  

pnniNbrPeerPortId 1.3.6.1.4.1.353.5.4.1.1.11.1.1
The port ID of a port to the neighboring peer that is in the Hello state 2-Way Inside.
OBJECT-TYPE    
  PnniPortId  

pnniNbrPeerPortFloodStatus 1.3.6.1.4.1.353.5.4.1.1.11.1.2
Indicates whether the port is being used for transmission of flooding and database synchronization information to the neighboring peer.
OBJECT-TYPE    
  TruthValue  

pnniSvccRccTable 1.3.6.1.4.1.353.5.4.1.1.12
A table containing the attributes necessary to analyze the operation of the PNNI protocol on SVCC-based Routing Control Channels. This entire object is read-only, reflecting the fact that SVCC-based RCCs are established dynamically during operation of the PNNI protocol rather than configured.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniSvccRccEntry

pnniSvccRccEntry 1.3.6.1.4.1.353.5.4.1.1.12.1
An entry in the table, containing information about an SVCC-based RCC from a PNNI logical node in this switching system.
OBJECT-TYPE    
  PnniSvccRccEntry  

pnniSvccRccIndex 1.3.6.1.4.1.353.5.4.1.1.12.1.1
An index into the node's tables of SVCC-based RCCs.
OBJECT-TYPE    
  PnniSvccRccIndex  

pnniSvccRccVersion 1.3.6.1.4.1.353.5.4.1.1.12.1.2
The version of the PNNI routing protocol used to exchange information with the neighbor node.
OBJECT-TYPE    
  PnniVersion  

pnniSvccRccHelloState 1.3.6.1.4.1.353.5.4.1.1.12.1.3
The state of the Hello protocol exchange over the SVCC-based RCC. Note: the Down state indicates that the SVCC establishment is in progress.
OBJECT-TYPE    
  PnniHelloState  

pnniSvccRccRemoteNodeId 1.3.6.1.4.1.353.5.4.1.1.12.1.4
The remote node at which the SVCC-based RCC terminates.
OBJECT-TYPE    
  PnniNodeId  

pnniSvccRccRemoteAtmAddress 1.3.6.1.4.1.353.5.4.1.1.12.1.5
The ATM End System Address to which SVCC establishment is attempted.
OBJECT-TYPE    
  PnniAtmAddr  

pnniSvccRccRcvHellos 1.3.6.1.4.1.353.5.4.1.1.12.1.6
A count of the number of Hello Packets received over this SVCC-based RCC.
OBJECT-TYPE    
  Counter32  

pnniSvccRccXmtHellos 1.3.6.1.4.1.353.5.4.1.1.12.1.7
A count of the number of Hello Packets transmitted over this SVCC-based RCC.
OBJECT-TYPE    
  Counter32  

pnniSvccRccIfIndex 1.3.6.1.4.1.353.5.4.1.1.12.1.8
The interface from which the SVCC-based RCC leaves the switching system. If the SVCC-based RCC has not yet been established, then this attribute takes the value of zero.
OBJECT-TYPE    
  InterfaceIndex  

pnniSvccRccVpi 1.3.6.1.4.1.353.5.4.1.1.12.1.9
The VPI used at the interface from which the SVCC-based RCC leaves the switching system. If the SVCC-based RCC has not yet been established, then this attribute takes the value of zero
OBJECT-TYPE    
  INTEGER 0..4095  

pnniSvccRccVci 1.3.6.1.4.1.353.5.4.1.1.12.1.10
The VCI used at the interface from which the SVCC-based RCC leaves the switching system. If the SVCC-based RCC has not yet been established, then this attribute takes the value of zero
OBJECT-TYPE    
  INTEGER 0..65535  

pnniPtseTable 1.3.6.1.4.1.353.5.4.1.1.13
The pnniPtse object contains the attributes that describe the most recent instances of PTSEs in a node's topology database. A concatenation of the Node Identifier of the local node that received the PTSE, the originating Node's Node Identifier and the PTSE Identifier are used to form the instance ID for an instance of this object.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniPtseEntry

pnniPtseEntry 1.3.6.1.4.1.353.5.4.1.1.13.1
An entry in the table, containing information about a PTSE in the topology database of a PNNI logical node in this switching system.
OBJECT-TYPE    
  PnniPtseEntry  

pnniPtseOriginatingNodeId 1.3.6.1.4.1.353.5.4.1.1.13.1.1
The Node Identifier of the node that originated the PTSE.
OBJECT-TYPE    
  PnniNodeId  

pnniPtseId 1.3.6.1.4.1.353.5.4.1.1.13.1.2
The value of the PTSE Identifier assigned to the PTSE by its originator.
OBJECT-TYPE    
  Unsigned32  

pnniPtseType 1.3.6.1.4.1.353.5.4.1.1.13.1.3
The type of information contained in the PTSE.
OBJECT-TYPE    
  INTEGER other(1), nodalStateParameters(96), nodalInformation(97), internalReachableAddresses(224), exteriorReachableAddresses(256), horizontalLinks(288), uplinks(289)  

pnniPtseSequenceNum 1.3.6.1.4.1.353.5.4.1.1.13.1.4
The sequence number of the instance of the PTSE as it appears in the local topology database.
OBJECT-TYPE    
  Unsigned32  

pnniPtseChecksum 1.3.6.1.4.1.353.5.4.1.1.13.1.5
The value of the PTSE checksum as it appears in the local topology database.
OBJECT-TYPE    
  Unsigned32 0..65535  

pnniPtseLifeTime 1.3.6.1.4.1.353.5.4.1.1.13.1.6
The value of the remaining lifetime for the given PTSE as it appears in the local topology database.
OBJECT-TYPE    
  Unsigned32 0..65535  

pnniPtseInfo 1.3.6.1.4.1.353.5.4.1.1.13.1.7
An unformatted hexadecimal dump of the PTSE contents in full. Note: If the size of the PTSE contents is larger than the maximum size of SNMP packets then this is truncated.
OBJECT-TYPE    
  OCTET STRING SIZE(0..65535)  

pnniMapTable 1.3.6.1.4.1.353.5.4.1.1.14
A table containing attributes necessary to find and analyze the operation of all links and nodes within the PNNI hierarchy, as seen from the perspective of a local node. An instance of a pnniMap Object describes a link in terms of a node at one end of the link. Normally there will be two instances of the pnniMap object in the MIB for each horizontal link. The two instances provide information for Network management to map port identifiers from the nodes at both ends to the link between them. A concatenation of the Local Node Index, Originating Node Identifier and Originating Port Identifier are used to form the instance ID for this object. This entire object is read-only, reflecting the fact that the map is discovered dynamically during operation of the PNNI protocol rather than configured.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniMapEntry

pnniMapEntry 1.3.6.1.4.1.353.5.4.1.1.14.1
An entry in the table, containing connectivity information about a node or link in the PNNI routing domain, as seen from the perspective of a PNNI logical node in this switching system.
OBJECT-TYPE    
  PnniMapEntry  

pnniMapOriginatingNodeId 1.3.6.1.4.1.353.5.4.1.1.14.1.1
The node identifier of the node whose connectivity within itself or to other nodes is being described.
OBJECT-TYPE    
  PnniNodeId  

pnniMapOriginatingPortId 1.3.6.1.4.1.353.5.4.1.1.14.1.2
The port identifier of the port as assigned by the originating node, to which the port is attached.
OBJECT-TYPE    
  PnniPortId  

pnniMapIndex 1.3.6.1.4.1.353.5.4.1.1.14.1.3
An index into the set of link and nodal connectivity associated with the originating node and port. This index is needed since there may be multiple entries for nodal connectivity from a specific node and port pair, in addition to any entry for a horizontal link or uplink.
OBJECT-TYPE    
  INTEGER 0..65535  

pnniMapType 1.3.6.1.4.1.353.5.4.1.1.14.1.4
The type of PNNI entity being described by this entry in the table.
OBJECT-TYPE    
  INTEGER horizontalLink(1), uplink(2), node(3)  

pnniMapPeerGroupId 1.3.6.1.4.1.353.5.4.1.1.14.1.5
Identifies the peer group of the originating node.
OBJECT-TYPE    
  PnniPeerGroupId  

pnniMapAggrToken 1.3.6.1.4.1.353.5.4.1.1.14.1.6
For horizontal links to/from LGNs and for uplinks, this attribute contains the derived aggregation token value for this link. For nodes and for horizontal links between lowest-level nodes, this attribute is set to zero.
OBJECT-TYPE    
  PnniAggrToken  

pnniMapRemoteNodeId 1.3.6.1.4.1.353.5.4.1.1.14.1.7
For horizontal links and uplinks, this attribute contains the node identifier of the node at the other end of the link from the originating node. If unknown, the PNNI protocol entity sets this attribute's value to (all) zero(s). For nodes, this attribute's value is set to (all) zero(s).
OBJECT-TYPE    
  PnniNodeId  

pnniMapRemotePortId 1.3.6.1.4.1.353.5.4.1.1.14.1.8
For horizontal links and uplinks, this attribute contains the port identifier of the port at the remote end of the link as assigned by the remote node. If unknown, the PNNI protocol entity sets this attribute's value to zero. For nodes, this attribute contains the port identifier of the port at the other end of the spoke or bypass from the originating port. When the originating port ID is zero, a value of zero indicates the default radius. When the originating port ID is non-zero, a value of zero indicates the nodal nucleus.
OBJECT-TYPE    
  PnniPortId  

pnniMapVPCapability 1.3.6.1.4.1.353.5.4.1.1.14.1.9
Indicates whether VPCs can be established across the PNNI entity being described by this entry in the pnniMapTable.
OBJECT-TYPE    
  TruthValue  

pnniMapPtseId 1.3.6.1.4.1.353.5.4.1.1.14.1.10
The value of the PTSE Identifier for the PTSE being originated by the originating node which contains the information group(s) describing the PNNI entity.
OBJECT-TYPE    
  Unsigned32  

pnniMapMetricsTag 1.3.6.1.4.1.353.5.4.1.1.14.1.11
An arbitrary integer that is used to associate a set of traffic parameters that are always advertised together. Within this set, the parameters are distinguished by the service categories and direction to which a set of parameters apply. This value is used as an index into the pnniMetricsTable. The distinguished value zero indicates that no metrics are associated with the link or nodal connectivity.
OBJECT-TYPE    
  PnniMetricsTag  

pnniMapNodeTable 1.3.6.1.4.1.353.5.4.1.1.15
A list of nodes as seen from the perspective of a local node. The pnniMapNodeTable contains all information learned by the local node from nodal information PTSEs. This entire object is read-only, reflecting the fact that the map is discovered dynamically during operation of the PNNI protocol rather than configured.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniMapNodeEntry

pnniMapNodeEntry 1.3.6.1.4.1.353.5.4.1.1.15.1
An entry in the table, containing information about a node in the PNNI routing domain, as seen from the perspective of a logical node in this switching system.
OBJECT-TYPE    
  PnniMapNodeEntry  

pnniMapNodeId 1.3.6.1.4.1.353.5.4.1.1.15.1.1
Identifies the node whose nodal information is being described.
OBJECT-TYPE    
  PnniNodeId  

pnniMapNodePeerGroupId 1.3.6.1.4.1.353.5.4.1.1.15.1.2
Identifies the peer group of the originating node.
OBJECT-TYPE    
  PnniPeerGroupId  

pnniMapNodeAtmAddress 1.3.6.1.4.1.353.5.4.1.1.15.1.3
The ATM End System Address of the originating node.
OBJECT-TYPE    
  PnniAtmAddr  

pnniMapNodeRestrictedTransit 1.3.6.1.4.1.353.5.4.1.1.15.1.4
Indicates whether the originating node is restricted to only allow support of SVCs originating or terminating at this node. A value of `true' indicates that the transit capabilities are restricted, i.e., transit connections are not allowed, whereas a value of `false' indicates that transit connections are allowed. This attribute reflects the setting of the restricted transit bit received in the nodal information PTSE of the originating node.
OBJECT-TYPE    
  TruthValue  

pnniMapNodeComplexRep 1.3.6.1.4.1.353.5.4.1.1.15.1.5
Indicates whether the originating node uses the complex node representation. If the value is `true', the spokes and bypasses that make up the complex node representation should be found in the pnniMapTable. This attribute reflects the setting of the nodal representation bit received in the nodal information PTSE of the originating node.
OBJECT-TYPE    
  TruthValue  

pnniMapNodeRestrictedBranching 1.3.6.1.4.1.353.5.4.1.1.15.1.6
Indicates whether the originating node is able to support additional branches. If the value is 'false', then it can support additional branches. This attribute reflects the setting of the restricted branching bit received in the nodal information PTSE of the originating node.
OBJECT-TYPE    
  TruthValue  

pnniMapNodeDatabaseOverload 1.3.6.1.4.1.353.5.4.1.1.15.1.7
Indicates whether the originating node is currently operating in topology database overload state. This attribute has the same value as the Non-transit for PGL Election bit in the nodal information group originated by this node.
OBJECT-TYPE    
  TruthValue  

pnniMapNodeIAmLeader 1.3.6.1.4.1.353.5.4.1.1.15.1.8
Indicates whether the originating node claims to be peer group leader of its peer group. This attribute reflects the setting of the 'I am Leader' bit received in the nodal information PTSE of the originating node.
OBJECT-TYPE    
  TruthValue  

pnniMapNodeLeadershipPriority 1.3.6.1.4.1.353.5.4.1.1.15.1.9
The Leadership priority value advertised by the originating node.
OBJECT-TYPE    
  INTEGER 0..255  

pnniMapNodePreferredPgl 1.3.6.1.4.1.353.5.4.1.1.15.1.10
Identifies the node which the originating node believes should be or is peer group leader of its peer group. If the originating node has not chosen a Preferred PGL, this attribute's value is set to (all) zero(s).
OBJECT-TYPE    
  PnniNodeId  

pnniMapNodeParentNodeId 1.3.6.1.4.1.353.5.4.1.1.15.1.11
When the originating node is a peer group leader, indicates the node ID of the parent LGN. If the originating node is not peer group leader of its peer group, this attribute's value is set to (all) zero(s).
OBJECT-TYPE    
  PnniNodeId  

pnniMapNodeParentAtmAddress 1.3.6.1.4.1.353.5.4.1.1.15.1.12
When the originating node is a peer group leader, indicates the ATM address of the parent LGN. If the originating node is not peer group leader of its peer group, this attribute's value is set to (all) zero(s).
OBJECT-TYPE    
  PnniAtmAddr  

pnniMapNodeParentPeerGroupId 1.3.6.1.4.1.353.5.4.1.1.15.1.13
When the originating node is a peer group leader, indicates the node's parent peer group ID. If the originating node is not peer group leader of its peer group, this attribute's value is set to (all) zero(s).
OBJECT-TYPE    
  PnniPeerGroupId  

pnniMapNodeParentPglNodeId 1.3.6.1.4.1.353.5.4.1.1.15.1.14
When the originating node is a peer group leader, identifies the node elected as peer group leader of the parent peer group. If the originating node is not peer group leader of its peer group, this attribute's value is set to (all) zero(s).
OBJECT-TYPE    
  PnniNodeId  

pnniMapAddrTable 1.3.6.1.4.1.353.5.4.1.1.16
The pnniMapAddr MIB Object contains a list of all reachable addresses from each node visible to the local node. The Local Node Index, Advertising Node ID, Advertised Port ID, Reachable Address, and Address prefix length are combined to form an instance ID for this object. The entire object is read-only, reflecting the fact that reachable addresses are discovered during dynamic operation of the PNNI protocol rather than configured.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniMapAddrEntry

pnniMapAddrEntry 1.3.6.1.4.1.353.5.4.1.1.16.1
An entry in the table, containing information about an address prefix reachable from a node in the PNNI routing domain, as seen from the perspective of a PNNI logical node in this switching system.
OBJECT-TYPE    
  PnniMapAddrEntry  

pnniMapAddrAdvertisingNodeId 1.3.6.1.4.1.353.5.4.1.1.16.1.1
The node ID of a node advertising reachability to the address prefix.
OBJECT-TYPE    
  PnniNodeId  

pnniMapAddrAdvertisedPortId 1.3.6.1.4.1.353.5.4.1.1.16.1.2
The port identifier used from the advertising node to reach the given address prefix.
OBJECT-TYPE    
  PnniPortId  

pnniMapAddrIndex 1.3.6.1.4.1.353.5.4.1.1.16.1.3
An arbitrary index that is used to enumerate all of the addresses advertised by the specified node.
OBJECT-TYPE    
  INTEGER 1..2147483647  

pnniMapAddrAddress 1.3.6.1.4.1.353.5.4.1.1.16.1.4
The value of the ATM End System Address prefix.
OBJECT-TYPE    
  AtmAddrPrefix  

pnniMapAddrPrefixLength 1.3.6.1.4.1.353.5.4.1.1.16.1.5
The Prefix length to be applied to the ATM End System Address prefix.
OBJECT-TYPE    
  PnniPrefixLength  

pnniMapTnsTable 1.3.6.1.4.1.353.5.4.1.1.17
A list of all reachable transit networks from each node visible to the local node. The Local Node Index, Advertising Node ID, Advertised Port ID, Transit Network Type, Transit Network Plan, and Transit Network ID are combined to form an instance ID for this object. The entire object is read-only, reflecting the fact that reachable transit networks are discovered during dynamic operation of the PNNI protocol rather than configured.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniMapTnsEntry

pnniMapTnsEntry 1.3.6.1.4.1.353.5.4.1.1.17.1
An entry in the table, containing information about a transit network reachable from a node in the PNNI routing domain, as seen from the perspective of a PNNI logical node in this switching system.
OBJECT-TYPE    
  PnniMapTnsEntry  

pnniMapTnsAdvertisingNodeId 1.3.6.1.4.1.353.5.4.1.1.17.1.1
The node ID of a node advertising reachability to the transit network.
OBJECT-TYPE    
  PnniNodeId  

pnniMapTnsAdvertisedPortId 1.3.6.1.4.1.353.5.4.1.1.17.1.2
The port identifier used from the advertising node to reach the given transit network.
OBJECT-TYPE    
  PnniPortId  

pnniMapTnsType 1.3.6.1.4.1.353.5.4.1.1.17.1.3
The type of network identification used for this transit network.
OBJECT-TYPE    
  TnsType  

pnniMapTnsPlan 1.3.6.1.4.1.353.5.4.1.1.17.1.4
The network identification plan according to which network identification has been assigned.
OBJECT-TYPE    
  TnsPlan  

pnniMapTnsId 1.3.6.1.4.1.353.5.4.1.1.17.1.5
The value of the transit network identifier.
OBJECT-TYPE    
  DisplayString  

pnniMetricsTable 1.3.6.1.4.1.353.5.4.1.1.18
This entity's table of PNNI parameters either associated with a PNNI entity or for the connectivity between a PNNI node and a reachable address or transit network.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniMetricsEntry

pnniMetricsEntry 1.3.6.1.4.1.353.5.4.1.1.18.1
A set of parameters that applies to the connectivity from a certain node and port to another node or port or to one or more reachable address prefixes and/or transit networks, for one (or more) particular service category(s). Note that there can be multiple sets of parameters with the same tag, in which case all sets apply to the specified connectivity.
OBJECT-TYPE    
  PnniMetricsEntry  

pnniMetricsTag 1.3.6.1.4.1.353.5.4.1.1.18.1.1
An arbitrary integer that is used to associate a set of traffic parameters that are always advertised together. Within this set, the parameters are distinguished by the service categories and direction to which a set of parameters apply.
OBJECT-TYPE    
  PnniMetricsTag 1..2147483647  

pnniMetricsDirection 1.3.6.1.4.1.353.5.4.1.1.18.1.2
The direction, with respect to the advertising node, in which the parameters in this entry apply.
OBJECT-TYPE    
  INTEGER incoming(1), outgoing(2)  

pnniMetricsIndex 1.3.6.1.4.1.353.5.4.1.1.18.1.3
An index into the set of parameters associated with the given tag and direction.
OBJECT-TYPE    
  Integer32 1..2147483647  

pnniMetricsClasses 1.3.6.1.4.1.353.5.4.1.1.18.1.4
The service categories to which this set of parameters applies. This is an integer used as a bit mask with each bit that is set representing a single service category for which the resources indicated are available. Bit 5 represents CBR, bit 4 represents real-time VBR, bit 3 represents non-real-time VBR, bit 2 represents ABR, and bit 1 (LSB) represents UBR.
OBJECT-TYPE    
  INTEGER 0..31  

pnniMetricsGcacClp 1.3.6.1.4.1.353.5.4.1.1.18.1.5
Indicates whether the advertised GCAC parameters apply for CLP=0 traffic or for CLP=0+1 traffic.
OBJECT-TYPE    
  ClpType  

pnniMetricsAdminWeight 1.3.6.1.4.1.353.5.4.1.1.18.1.6
The administrative weight from the advertising node to the remote end of the PNNI entity or to the reachable address or transit network, for the specified service categories.
OBJECT-TYPE    
  Unsigned32 1..16777215  

pnniMetrics1 1.3.6.1.4.1.353.5.4.1.1.18.1.7
An alternate routing parameter from the advertising node to the remote end of the PNNI entity or to the reachable address or transit network, for the specified service categories. For information learned from PNNI nodes, this is the maximum cell rate in cells per second for the specified service categories. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniMetrics2 1.3.6.1.4.1.353.5.4.1.1.18.1.8
An alternate routing parameter from the advertising node to the remote end of the PNNI entity or to the reachable address or transit network, for the specified service categories. For information learned from PNNI nodes, this is the available cell rate in cells per second for the specified service categories. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniMetrics3 1.3.6.1.4.1.353.5.4.1.1.18.1.9
An alternate routing parameter from the advertising node to the remote end of the PNNI entity or to the reachable address or transit network, for the specified service categories. For information learned from PNNI nodes, this is the maximum cell transfer delay in microseconds for the specified service categories. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniMetrics4 1.3.6.1.4.1.353.5.4.1.1.18.1.10
An alternate routing parameter from the advertising node to the remote end of the PNNI entity or to the reachable address or transit network, for the specified service categories. For information learned from PNNI nodes, this is the cell delay variation in microseconds for the specified service categories. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniMetrics5 1.3.6.1.4.1.353.5.4.1.1.18.1.11
An alternate routing parameter from the advertising node to the remote end of the PNNI entity or to the reachable address or transit network, for the specified service categories. For PNNI, this is the cell loss ratio for CLP=0 traffic for the specified service categories. The cell loss ratio value is computed as 10**(-n) where 'n' is the value returned in this variable. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniMetrics6 1.3.6.1.4.1.353.5.4.1.1.18.1.12
An alternate routing parameter from the advertising node to the remote end of the PNNI entity or to the reachable address or transit network, for the specified service categories. For PNNI, this is the cell loss ratio for CLP=0+1 traffic for the specified service categories. The cell loss ratio value is computed as 10**(-n) where 'n' is the value returned in this variable. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniMetrics7 1.3.6.1.4.1.353.5.4.1.1.18.1.13
An alternate routing parameter from the advertising node to the remote end of the PNNI entity or to the reachable address or transit network, for the specified service categories. For information learned from PNNI nodes, this is the cell rate margin in cells per second for the specified service categories. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniMetrics8 1.3.6.1.4.1.353.5.4.1.1.18.1.14
An alternate routing parameter from the advertising node to the remote end of the PNNI entity or to the reachable address or transit network, for the specified service categories. For information learned from PNNI nodes, this is the variance factor in units of 2**(-8) for the specified service categories. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniMetricsRowStatus 1.3.6.1.4.1.353.5.4.1.1.18.1.15
To create, delete, activate and de-activate a set of metrics.
OBJECT-TYPE    
  RowStatus  

pnniRoutingGroup 1.3.6.1.4.1.353.5.4.1.1.19
OBJECT IDENTIFIER    

pnniRouteBaseGroup 1.3.6.1.4.1.353.5.4.1.1.19.1
OBJECT IDENTIFIER    

pnniRouteNodeNumber 1.3.6.1.4.1.353.5.4.1.1.19.1.1
The number of current precalculated PNNI routes to PNNI nodes that are not invalid.
OBJECT-TYPE    
  Gauge32  

pnniRouteAddrNumber 1.3.6.1.4.1.353.5.4.1.1.19.1.2
The number of current PNNI routes from nodes in the PNNI routing domain to addresses and transit networks that are not invalid.
OBJECT-TYPE    
  Gauge32  

pnniRouteNodeTable 1.3.6.1.4.1.353.5.4.1.1.19.2
This entity's PNNI Routing table (of routes to other nodes).
OBJECT-TYPE    
  SEQUENCE OF  
    PnniRouteNodeEntry

pnniRouteNodeEntry 1.3.6.1.4.1.353.5.4.1.1.19.2.1
A particular route to a particular destination node, under a particular policy.
OBJECT-TYPE    
  PnniRouteNodeEntry  

pnniRouteNodeClass 1.3.6.1.4.1.353.5.4.1.1.19.2.1.1
Indicates the service category with which this forwarding table entry is associated.
OBJECT-TYPE    
  ServiceCategory  

pnniRouteNodeDestNodeId 1.3.6.1.4.1.353.5.4.1.1.19.2.1.2
The node ID of the destination node to which this route proceeds, and at which the DTL stack for this route terminates.
OBJECT-TYPE    
  PnniNodeId  

pnniRouteNodeDTL 1.3.6.1.4.1.353.5.4.1.1.19.2.1.3
The index into the owning PNNI node's DTL table of the DTL stack that goes with this route.
OBJECT-TYPE    
  Integer32 1..2147483647  

pnniRouteNodeDestPortId 1.3.6.1.4.1.353.5.4.1.1.19.2.1.4
The port ID of the destination node at which the route terminates. A port ID of zero indicates the node nucleus. When the destination node is represented by the simple node representation, this value should be set to zero.
OBJECT-TYPE    
  PnniPortId  

pnniRouteNodeProto 1.3.6.1.4.1.353.5.4.1.1.19.2.1.5
The routing mechanism via which this route was learned.
OBJECT-TYPE    
  INTEGER other(1), local(2), mgmt(3), pnni(4)  

pnniRouteNodeTimeStamp 1.3.6.1.4.1.353.5.4.1.1.19.2.1.6
The time at which this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned.
OBJECT-TYPE    
  TimeStamp  

pnniRouteNodeInfo 1.3.6.1.4.1.353.5.4.1.1.19.2.1.7
A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's pnniRouteNodeProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER zeroDotZero.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

pnniRouteNodeGcacClp 1.3.6.1.4.1.353.5.4.1.1.19.2.1.8
For PNNI, indicates whether any advertised GCAC parameters apply for CLP=0 traffic or for CLP=0+1 traffic.
OBJECT-TYPE    
  ClpType  

pnniRouteNodeFwdMetricAW 1.3.6.1.4.1.353.5.4.1.1.19.2.1.9
The cumulative administrative weight calculated for the forward direction of this route. If this metric is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeFwdMetric1 1.3.6.1.4.1.353.5.4.1.1.19.2.1.10
An alternate routing parameter for the forward direction of this route. For information learned from PNNI nodes, this is the maximum possible cell rate (in cells per second) for the forward direction of the route. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeFwdMetric2 1.3.6.1.4.1.353.5.4.1.1.19.2.1.11
An alternate routing parameter for the forward direction of this route. For information learned from PNNI nodes, this is the Available cell rate (in cells per second) for the forward direction of the route. Further information on available bandwidth may be obtainable by reference to the nodal advertisements of the nodes in the path. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeFwdMetric3 1.3.6.1.4.1.353.5.4.1.1.19.2.1.12
An alternate routing parameter for the forward direction of this route. For information learned from PNNI nodes, this is the cumulative Maximum Cell Transfer Delay (in microseconds) for the forward direction of the route. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeFwdMetric4 1.3.6.1.4.1.353.5.4.1.1.19.2.1.13
An alternate routing parameter for the forward direction of this route. For information learned from PNNI nodes, this is the cumulative Cell Delay Variation (in microseconds) for the forward direction of the route. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeFwdMetric5 1.3.6.1.4.1.353.5.4.1.1.19.2.1.14
An alternate routing parameter for the forward direction of this route. For information learned from PNNI nodes, this is the cumulative Cell Loss Ratio for CLP=0 traffic for the forward direction of the route. The cell loss ratio value is computed as 10**(-n) where 'n' is the value returned in this variable. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeFwdMetric6 1.3.6.1.4.1.353.5.4.1.1.19.2.1.15
An alternate routing parameter for the forward direction of this route. For information learned from PNNI nodes, this is the cumulative Cell Loss Ratio for CLP=0+1 traffic for the forward direction of the route. The cell loss ratio value is computed as 10**(-n) where 'n' is the value returned in this variable. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeFwdMetric7 1.3.6.1.4.1.353.5.4.1.1.19.2.1.16
An alternate routing parameter for the forward direction of this route. For information learned from PNNI nodes, this is the Cell Rate Margin (in cells per second) for the forward direction of the route. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeFwdMetric8 1.3.6.1.4.1.353.5.4.1.1.19.2.1.17
An alternate routing parameter for the forward direction of this route. For information learned from PNNI nodes, this is the Variance Factor (in units of 2**(-8)) for the forward direction of the route. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeBwdMetricAW 1.3.6.1.4.1.353.5.4.1.1.19.2.1.18
The administrative weight calculated for the backward direction of this route. If this metric is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeBwdMetric1 1.3.6.1.4.1.353.5.4.1.1.19.2.1.19
An alternate routing parameter for the backward direction of this route. For information learned from PNNI nodes, this is the maximum possible cell rate (in cells per second) for the backward direction of the route. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeBwdMetric2 1.3.6.1.4.1.353.5.4.1.1.19.2.1.20
An alternate routing parameter for the backward direction of this route. For information learned from PNNI nodes, this is the Available cell rate (in cells per second) for the backward direction of the route. Further information on available bandwidth may be obtainable by reference to the nodal advertisements of the nodes in the path. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeBwdMetric3 1.3.6.1.4.1.353.5.4.1.1.19.2.1.21
An alternate routing parameter for the backward direction of this route. For information learned from PNNI nodes, this is the cumulative Maximum Cell Transfer Delay (in microseconds) for the backward direction of the route. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeBwdMetric4 1.3.6.1.4.1.353.5.4.1.1.19.2.1.22
An alternate routing parameter for the backward direction of this route. For information learned from PNNI nodes, this is the cumulative Cell Delay Variation (in microseconds) for the backward direction of the route. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeBwdMetric5 1.3.6.1.4.1.353.5.4.1.1.19.2.1.23
An alternate routing parameter for the backward direction of this route. For information learned from PNNI nodes, this is the cumulative Cell Loss Ratio for CLP=0 traffic for the backward direction of the route. The cell loss ratio value is computed as 10**(-n) where 'n' is the value returned in this variable. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeBwdMetric6 1.3.6.1.4.1.353.5.4.1.1.19.2.1.24
An alternate routing parameter for the backward direction of this route. For information learned from PNNI nodes, this is the cumulative Cell Loss Ratio for CLP=0+1 traffic for the backward direction of the route. The cell loss ratio value is computed as 10**(-n) where 'n' is the value returned in this variable. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeBwdMetric7 1.3.6.1.4.1.353.5.4.1.1.19.2.1.25
An alternate routing parameter for the backward direction of this route. For information learned from PNNI nodes, this is the Cell Rate Margin (in cells per second) for the backward direction of the route. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeBwdMetric8 1.3.6.1.4.1.353.5.4.1.1.19.2.1.26
An alternate routing parameter for the backward direction of this route. For information learned from PNNI nodes, this is the Variance Factor (in units of 2**(-8)) for the backward direction of the route. If this parameter is not used, its value should be set to 0xFFFFFFFF.
OBJECT-TYPE    
  Unsigned32  

pnniRouteNodeVPCapability 1.3.6.1.4.1.353.5.4.1.1.19.2.1.27
This attribute indicates whether a VPC setup on this route is possible.
OBJECT-TYPE    
  TruthValue  

pnniRouteNodeStatus 1.3.6.1.4.1.353.5.4.1.1.19.2.1.28
The row status variable, used according to row installation and removal conventions.
OBJECT-TYPE    
  RowStatus  

pnniDTLTable 1.3.6.1.4.1.353.5.4.1.1.19.3
The set of all DTL stacks used for the pre-computed routes maintained by this managed entity.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniDTLEntry

pnniDTLEntry 1.3.6.1.4.1.353.5.4.1.1.19.3.1
A segment of a DTL stack. The complete DTL stack is formed by traversing the rows of the table for which the pnniDTLIndex is the same. Level transitions are indicated using the pnniDLTLinkType column.
OBJECT-TYPE    
  PnniDTLEntry  

pnniDTLIndex 1.3.6.1.4.1.353.5.4.1.1.19.3.1.1
The index in the node's DTL table of this DTL stack.
OBJECT-TYPE    
  Integer32 1..2147483647  

pnniDTLEntryIndex 1.3.6.1.4.1.353.5.4.1.1.19.3.1.2
The index in the current DTL stack of this entry.
OBJECT-TYPE    
  Integer32 1..200  

pnniDTLNodeId 1.3.6.1.4.1.353.5.4.1.1.19.3.1.3
The node which is this hop in the DTL stack.
OBJECT-TYPE    
  PnniNodeId  

pnniDTLPortId 1.3.6.1.4.1.353.5.4.1.1.19.3.1.4
The port from the pnniDTLNodeId to use as the exit. If the DTL stack does not care, this is coded as zero.
OBJECT-TYPE    
  PnniPortId  

pnniDTLLinkType 1.3.6.1.4.1.353.5.4.1.1.19.3.1.5
The type of link out from this node (pnniDTLNodeId). This is well defined even if the specific port is not specified.
OBJECT-TYPE    
  INTEGER invalid(1), horizontal(2), uplink(3), last(4)  

pnniDTLStatus 1.3.6.1.4.1.353.5.4.1.1.19.3.1.6
The row status variable, used according to row installation and removal conventions.
OBJECT-TYPE    
  RowStatus  

pnniRouteAddrTable 1.3.6.1.4.1.353.5.4.1.1.19.4
A table containing all the attributes necessary to determine what the PNNI entity believes is reachable in terms of ATM End System Addresses and to determine which nodes are advertising this reachability. This table is also used to configure static routes to reachable address prefixes. The local node index that received the reachability information, reachable address, address prefix length, and an index that distinguishes between multiple listings of connectivity to a given address prefix from a given local node are combined to form an instance ID for this object.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniRouteAddrEntry

pnniRouteAddrEntry 1.3.6.1.4.1.353.5.4.1.1.19.4.1
An entry in the table, containing information about a reachable address prefix.
OBJECT-TYPE    
  PnniRouteAddrEntry  

pnniRouteAddrAddress 1.3.6.1.4.1.353.5.4.1.1.19.4.1.1
The value of the ATM End System Address prefix.
OBJECT-TYPE    
  AtmAddrPrefix  

pnniRouteAddrPrefixLength 1.3.6.1.4.1.353.5.4.1.1.19.4.1.2
The prefix length to be applied to the ATM End System Address prefix.
OBJECT-TYPE    
  PnniPrefixLength  

pnniRouteAddrIndex 1.3.6.1.4.1.353.5.4.1.1.19.4.1.3
An index into the set of listings of connectivity to a given address prefix from a given local node.
OBJECT-TYPE    
  Integer32 1..65535  

pnniRouteAddrIfIndex 1.3.6.1.4.1.353.5.4.1.1.19.4.1.4
The local interface over which the reachable address can be reached. The value zero indicates an unknown interface or reachability through a remote node. This object may only have a non-zero value if the value of the corresponding instance of pnniRouteAddrProto is other than 'pnni', pnniRouteAddrType is other than 'reject', and the node identified by pnniRouteAddrAdvertisingNodeId is instantiated within this switching system.
OBJECT-TYPE    
  InterfaceIndex  

pnniRouteAddrAdvertisingNodeId 1.3.6.1.4.1.353.5.4.1.1.19.4.1.5
The node ID of a node advertising reachability to the address prefix. If the local node index is zero, then the advertising node ID must be set to all zeros.
OBJECT-TYPE    
  PnniNodeId  

pnniRouteAddrAdvertisedPortId 1.3.6.1.4.1.353.5.4.1.1.19.4.1.6
The port identifier used from the advertising node to reach the given address prefix.
OBJECT-TYPE    
  PnniPortId  

pnniRouteAddrType 1.3.6.1.4.1.353.5.4.1.1.19.4.1.7
The type (e.g. internal or exterior) of reachability from the advertising node to the address prefix. Reject(2) refers to an address prefix which, if matched, indicates that the message should be discarded as unreachable. This is used in some protocols as a means of correctly aggregating routes.
OBJECT-TYPE    
  INTEGER other(1), reject(2), internal(3), exterior(4)  

pnniRouteAddrProto 1.3.6.1.4.1.353.5.4.1.1.19.4.1.8
The routing mechanism via which the connectivity from the advertising node to the reachable address prefix was learned.
OBJECT-TYPE    
  INTEGER other(1), local(2), mgmt(3), pnni(4)  

pnniRouteAddrPnniScope 1.3.6.1.4.1.353.5.4.1.1.19.4.1.9
The PNNI scope of advertisement (i.e. level of PNNI hierarchy) of the reachability from the advertising node to the address prefix.
OBJECT-TYPE    
  PnniLevel  

pnniRouteAddrVPCapability 1.3.6.1.4.1.353.5.4.1.1.19.4.1.10
Indicates whether VPCs can be established from the advertising node to the reachable address prefix.
OBJECT-TYPE    
  TruthValue  

pnniRouteAddrMetricsTag 1.3.6.1.4.1.353.5.4.1.1.19.4.1.11
The index into the pnniMetricsTable for the traffic parameter values that apply for the connectivity from the advertising node to the reachable address prefix. There will be one or more entries in the pnniMetricsTable whose first instance identifier matches the value of this variable. If there are no parameters associated with this reachable address prefix then the distinguished value zero is used.
OBJECT-TYPE    
  PnniMetricsTag  

pnniRouteAddrPtseId 1.3.6.1.4.1.353.5.4.1.1.19.4.1.12
For reachable addresses learned via PNNI, this attribute contains the value of the PTSE Identifier for the PTSE being originated by the originating node which contains the information group(s) describing the reachable address. For reachable addresses learned by means other than PNNI, this attribute is set to zero.
OBJECT-TYPE    
  Unsigned32  

pnniRouteAddrOriginateAdvertisement 1.3.6.1.4.1.353.5.4.1.1.19.4.1.13
Whether or not the reachable address specified by this entry is to be advertised by the local node into its PNNI routing domain. This object may only take on the value 'true' when the value of the corresponding instance of pnniRouteAddrProto is other than 'pnni'.
OBJECT-TYPE    
  TruthValue  

pnniRouteAddrInfo 1.3.6.1.4.1.353.5.4.1.1.19.4.1.14
A reference to MIB definitions specific to the particular routing protocol which is responsible for this reachable address prefix, as determined by the value specified in the route's pnniRouteAddrProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER zeroDotZero.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

pnniRouteAddrOperStatus 1.3.6.1.4.1.353.5.4.1.1.19.4.1.15
Indicates whether the reachable address prefix is operationally valid and whether it is being advertised by this node.
OBJECT-TYPE    
  INTEGER inactive(1), active(2), advertised(3)  

pnniRouteAddrTimeStamp 1.3.6.1.4.1.353.5.4.1.1.19.4.1.16
Indicates when the connectivity from the advertising node to the reachable address prefix became known to the local node.
OBJECT-TYPE    
  TimeStamp  

pnniRouteAddrRowStatus 1.3.6.1.4.1.353.5.4.1.1.19.4.1.17
To create, delete, activate and de-activate a reachable address prefix.
OBJECT-TYPE    
  RowStatus  

pnniRouteTnsTable 1.3.6.1.4.1.353.5.4.1.1.19.5
A table containing all the attributes necessary to determine what transit networks the PNNI entity believes are reachable and to determine which nodes are advertising this reachability. This table is also used to add static routes to reachable transit networks. The local node index which received the reachability information, type of network identification, network identification plan, transit network identifier, and an index that distinguishes between multiple listings of connectivity to a given transit network from a given local node are combined to form an instance ID for this object.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniRouteTnsEntry

pnniRouteTnsEntry 1.3.6.1.4.1.353.5.4.1.1.19.5.1
An entry in the table, containing information about a reachable transit network.
OBJECT-TYPE    
  PnniRouteTnsEntry  

pnniRouteTnsType 1.3.6.1.4.1.353.5.4.1.1.19.5.1.1
The type of network identification used for this transit network.
OBJECT-TYPE    
  TnsType  

pnniRouteTnsPlan 1.3.6.1.4.1.353.5.4.1.1.19.5.1.2
The network identification plan according to which network identification has been assigned.
OBJECT-TYPE    
  TnsPlan  

pnniRouteTnsId 1.3.6.1.4.1.353.5.4.1.1.19.5.1.3
The value of the transit network identifier.
OBJECT-TYPE    
  DisplayString  

pnniRouteTnsIndex 1.3.6.1.4.1.353.5.4.1.1.19.5.1.4
An index into the set of listings of connectivity to a given transit network from a given local node.
OBJECT-TYPE    
  Integer32 1..65535  

pnniRouteTnsIfIndex 1.3.6.1.4.1.353.5.4.1.1.19.5.1.5
The local interface over which the transit network can be reached. The value zero indicates an unknown interface or reachability through a remote node. This object may only have a non-zero value if the value of the corresponding instance of pnniRouteTnsProto is other than 'pnni' and the node identified by pnniRouteTnsAdvertisingNodeId is instantiated within this switching system.
OBJECT-TYPE    
  InterfaceIndex  

pnniRouteTnsAdvertisingNodeId 1.3.6.1.4.1.353.5.4.1.1.19.5.1.6
The node ID of a node advertising reachability to the transit network. If the local node index is zero, then the advertising node ID must also be set to zero.
OBJECT-TYPE    
  PnniNodeId  

pnniRouteTnsAdvertisedPortId 1.3.6.1.4.1.353.5.4.1.1.19.5.1.7
The port identifier used from the advertising node to reach the given transit network.
OBJECT-TYPE    
  PnniPortId  

pnniRouteTnsRouteType 1.3.6.1.4.1.353.5.4.1.1.19.5.1.8
The type (e.g. exterior or other) of reachability from the advertising node to the transit network.
OBJECT-TYPE    
  INTEGER other(1), exterior(4)  

pnniRouteTnsProto 1.3.6.1.4.1.353.5.4.1.1.19.5.1.9
The routing mechanism via which the connectivity from the advertising node to the transit network was learned.
OBJECT-TYPE    
  INTEGER other(1), local(2), mgmt(3), pnni(4)  

pnniRouteTnsPnniScope 1.3.6.1.4.1.353.5.4.1.1.19.5.1.10
The PNNI scope of advertisement (i.e. level of PNNI hierarchy) of the reachability from the advertising node to the transit network.
OBJECT-TYPE    
  PnniLevel  

pnniRouteTnsVPCapability 1.3.6.1.4.1.353.5.4.1.1.19.5.1.11
Indicates whether VPCs can be established from the advertising node to the reachable transit network.
OBJECT-TYPE    
  TruthValue  

pnniRouteTnsMetricsTag 1.3.6.1.4.1.353.5.4.1.1.19.5.1.12
The index into the pnniMetricsTable for the traffic parameter values that apply for the connectivity from the advertising node to the transit network. There will be one or more entries in the pnniMetricsTable whose first instance identifier matches the value of this variable. If there are no parameters associated with this transit network then the distinguished value zero is used.
OBJECT-TYPE    
  PnniMetricsTag  

pnniRouteTnsPtseId 1.3.6.1.4.1.353.5.4.1.1.19.5.1.13
For reachable transit networks learned via PNNI, this attribute contains the value of the PTSE Identifier for the PTSE being originated by the originating node which contains the information group(s) describing the transit network. For reachable transit networks learned by means other than PNNI, this attribute is set to zero.
OBJECT-TYPE    
  Unsigned32  

pnniRouteTnsOriginateAdvertisement 1.3.6.1.4.1.353.5.4.1.1.19.5.1.14
Whether or not the transit network specified by this entry is to be advertised by the local node into its PNNI routing domain. This object may only take on the value 'true' when the value of the corresponding instance of pnniRouteNodeProto is other than 'pnni'.
OBJECT-TYPE    
  TruthValue  

pnniRouteTnsInfo 1.3.6.1.4.1.353.5.4.1.1.19.5.1.15
A reference to MIB definitions specific to the particular routing protocol which is responsible for this transit network, as determined by the value specified in the route's pnniRouteTnsProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER zeroDotZero.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

pnniRouteTnsOperStatus 1.3.6.1.4.1.353.5.4.1.1.19.5.1.16
Indicates whether the reachable transit network is operationally valid and whether it is being advertised by this node.
OBJECT-TYPE    
  INTEGER inactive(1), active(2), advertised(3)  

pnniRouteTnsTimeStamp 1.3.6.1.4.1.353.5.4.1.1.19.5.1.17
Indicates how long the connectivity from the advertising node to the reachable transit network has been known to the local node.
OBJECT-TYPE    
  TimeStamp  

pnniRouteTnsRowStatus 1.3.6.1.4.1.353.5.4.1.1.19.5.1.18
To create, delete, activate and de-activate a reachable transit network.
OBJECT-TYPE    
  RowStatus  

pnniSummaryAddressTable 1.3.6.1.4.1.353.5.4.1.1.20
A list of the summary address prefixes that may be advertised by the specified logical PNNI entity.
OBJECT-TYPE    
  SEQUENCE OF  
    PnniSummaryAddressEntry

pnniSummaryAddressEntry 1.3.6.1.4.1.353.5.4.1.1.20.1
An entry in the table, containing summary address prefix information in this switching system.
OBJECT-TYPE    
  PnniSummaryAddressEntry  

pnniSummaryAddressType 1.3.6.1.4.1.353.5.4.1.1.20.1.1
The type (e.g. internal or exterior) of summary being described.
OBJECT-TYPE    
  INTEGER internal(1), exterior(2)  

pnniSummaryAddressAddress 1.3.6.1.4.1.353.5.4.1.1.20.1.2
The ATM End System Address prefix for the summary.
OBJECT-TYPE    
  AtmAddrPrefix  

pnniSummaryAddressPrefixLength 1.3.6.1.4.1.353.5.4.1.1.20.1.3
The prefix length for the summary.
OBJECT-TYPE    
  PnniPrefixLength  

pnniSummaryAddressSuppress 1.3.6.1.4.1.353.5.4.1.1.20.1.4
Determines what is done with addresses that are being summarized by the instance. The default value (e.g. false) will indicate that the summary should propagate into the peer group. Network Management will be able to set the value of this attribute to `suppress' (e.g. true), which suppresses the summary and any reachable addresses it summarizes from being advertised into the peer group.
OBJECT-TYPE    
  TruthValue  

pnniSummaryAddressState 1.3.6.1.4.1.353.5.4.1.1.20.1.5
Indicates whether the summary is currently being advertised by the node within the local switching system into its peer group.
OBJECT-TYPE    
  INTEGER advertising(1), suppressing(2), inactive(3)  

pnniSummaryAddressRowStatus 1.3.6.1.4.1.353.5.4.1.1.20.1.6
To create, delete, activate and de-activate a summary.
OBJECT-TYPE    
  RowStatus  

pnniMIBConformance 1.3.6.1.4.1.353.5.4.1.2
OBJECT IDENTIFIER    

pnniMIBCompliances 1.3.6.1.4.1.353.5.4.1.2.1
OBJECT IDENTIFIER    

pnniMIBCompliance 1.3.6.1.4.1.353.5.4.1.2.1.1
The compliance statement for entities which implement the PNNI MIB. Groups of PNNI objects required for management of a minimum function node are identified by the suffix MinGroup. Groups of PNNI objects required for management of a border node are identified by the suffix BorderGroup. Groups of PNNI objects required for management of a PGL/LGN capable node are identified by the suffix LgnGroup. Groups of optional PNNI objects are identified by the suffix OptionalGroup.
MODULE-COMPLIANCE    

pnniMIBGroups 1.3.6.1.4.1.353.5.4.1.2.2
OBJECT IDENTIFIER    

pnniGeneralMinGroup 1.3.6.1.4.1.353.5.4.1.2.2.1
A collection of general PNNI objects required for management of a minimum function switching system.
OBJECT-GROUP    

pnniGeneralBorderGroup 1.3.6.1.4.1.353.5.4.1.2.2.2
A collection of general PNNI objects required for management of a border node.
OBJECT-GROUP    

pnniNodeMinGroup 1.3.6.1.4.1.353.5.4.1.2.2.3
A collection of per node PNNI objects required for management of a minimum function switching system.
OBJECT-GROUP    

pnniNodePglMinGroup 1.3.6.1.4.1.353.5.4.1.2.2.4
A collection of per node PGL election related PNNI objects required for management of a minimum function switching system.
OBJECT-GROUP    

pnniNodePglLgnGroup 1.3.6.1.4.1.353.5.4.1.2.2.5
A collection of per node PGL election related PNNI objects required for management of a PGL/LGN capable switching system.
OBJECT-GROUP    

pnniNodeTimerMinGroup 1.3.6.1.4.1.353.5.4.1.2.2.6
A collection of per node PNNI objects required for management of timers and significant change thresholds in a minimum function switching system.
OBJECT-GROUP    

pnniNodeTimerLgnGroup 1.3.6.1.4.1.353.5.4.1.2.2.7
A collection of per node PNNI objects required for management of timers in a PGL/LGN capable switching system.
OBJECT-GROUP    

pnniNodeSvccLgnGroup 1.3.6.1.4.1.353.5.4.1.2.2.8
A collection of per node SVCC-based RCC related PNNI objects required for management of a PGL/LGN capable switching system.
OBJECT-GROUP    

pnniScopeMinGroup 1.3.6.1.4.1.353.5.4.1.2.2.9
A collection of per node scope mapping related PNNI objects required for management of a minimum function switching system.
OBJECT-GROUP    

pnniSummaryLgnGroup 1.3.6.1.4.1.353.5.4.1.2.2.10
A collection of PNNI objects required for controlling address summarization.
OBJECT-GROUP    

pnniIfMinGroup 1.3.6.1.4.1.353.5.4.1.2.2.11
A collection of per interface PNNI objects required for management of a minimum function switching system.
OBJECT-GROUP    

pnniIfBorderGroup 1.3.6.1.4.1.353.5.4.1.2.2.12
A collection of per interface PNNI objects required for management of a border node.
OBJECT-GROUP    

pnniLinkMinGroup 1.3.6.1.4.1.353.5.4.1.2.2.13
A collection of per link PNNI objects required for management of a minimum function switching system.
OBJECT-GROUP    

pnniLinkBorderOrLgnGroup 1.3.6.1.4.1.353.5.4.1.2.2.14
A collection of per link PNNI objects required for management of a border node or a PGL/LGN capable switching system.
OBJECT-GROUP    

pnniLinkLgnGroup 1.3.6.1.4.1.353.5.4.1.2.2.15
A collection of per link PNNI objects required for management of a PGL/LGN capable switching system.
OBJECT-GROUP    

pnniNbrPeerMinGroup 1.3.6.1.4.1.353.5.4.1.2.2.16
A collection of per neighboring peer PNNI objects required for management of a minimum function switching system.
OBJECT-GROUP    

pnniNbrPeerLgnGroup 1.3.6.1.4.1.353.5.4.1.2.2.17
A collection of per neighboring peer PNNI objects required for management of a PGL/LGN capable switching system.
OBJECT-GROUP    

pnniNbrPeerPortMinGroup 1.3.6.1.4.1.353.5.4.1.2.2.18
A collection of per port to neighboring peer PNNI objects required for management of a minimum function switching system.
OBJECT-GROUP    

pnniSvccRccLgnGroup 1.3.6.1.4.1.353.5.4.1.2.2.19
A collection of per SVCC-based RCC PNNI objects required for management of a PGL/LGN capable switching system.
OBJECT-GROUP    

pnniPtseOptionalGroup 1.3.6.1.4.1.353.5.4.1.2.2.20
A collection of optional per PTSE PNNI objects.
OBJECT-GROUP    

pnniMapOptionalGroup 1.3.6.1.4.1.353.5.4.1.2.2.21
A collection of optional PNNI objects used to create a map of nodes and links in the PNNI routing domain.
OBJECT-GROUP    

pnniMapNodeOptionalGroup 1.3.6.1.4.1.353.5.4.1.2.2.22
A collection of optional PNNI objects used to create a map of nodes in the PNNI routing domain.
OBJECT-GROUP    

pnniMapAddrOptionalGroup 1.3.6.1.4.1.353.5.4.1.2.2.23
A collection of optional PNNI objects used to create a map of reachable addresses in the PNNI routing domain.
OBJECT-GROUP    

pnniMapTnsOptionalGroup 1.3.6.1.4.1.353.5.4.1.2.2.24
A collection of optional PNNI objects used to create a map of reachable transit networks in the PNNI routing domain.
OBJECT-GROUP    

pnniMetricsOptionalGroup 1.3.6.1.4.1.353.5.4.1.2.2.25
A collection of optional PNNI objects used to manage metrics and attributes associated with PNNI entities.
OBJECT-GROUP    

pnniRouteGeneralOptionalGroup 1.3.6.1.4.1.353.5.4.1.2.2.26
A collection of optional PNNI objects.
OBJECT-GROUP    

pnniRouteNodeOptionalGroup 1.3.6.1.4.1.353.5.4.1.2.2.27
A collection of optional PNNI objects used to manage precalculated routes to nodes in the PNNI routing domain.
OBJECT-GROUP    

pnniDTLOptionalGroup 1.3.6.1.4.1.353.5.4.1.2.2.28
A collection of optional PNNI objects used to manage precalculated routes to nodes in the PNNI routing domain.
OBJECT-GROUP    

pnniRouteAddrOptionalGroup 1.3.6.1.4.1.353.5.4.1.2.2.29
A collection of optional PNNI objects used to manage routes to reachable addresses in the PNNI routing domain.
OBJECT-GROUP    

pnniRouteTnsOptionalGroup 1.3.6.1.4.1.353.5.4.1.2.2.30
A collection of optional PNNI objects used to manage routes to reachable transit networks in the PNNI routing domain.
OBJECT-GROUP    

pnniSummaryAddressLgnGroup 1.3.6.1.4.1.353.5.4.1.2.2.31
A collection of PNNI objects required for controlling address summarization.
OBJECT-GROUP    

Defined Objects

PnniAtmAddr  
The ATM address used by the network entity. The address types are: no address (0 octets), and NSAP (20 octets).
TEXTUAL-CONVENTION    
  OCTET STRING SIZE(0 | 20)  

PnniNodeIndex  
An index that identifies a logical PNNI entity within the managed system. The distinguished value zero indicates the null instance or no instance in the PnniNodeCfgParentNodeIndex. In all other cases, the distinguished value zero indicates a logical entity within the switching system that manages routes only over non-PNNI interfaces. By default, only the node identified by node index one is created, and all PNNI interfaces are associated with that node.
TEXTUAL-CONVENTION    
  Integer32 0..65535  

PnniNodeId  
A PNNI node ID - this is used to identify the logical PNNI node.
TEXTUAL-CONVENTION    
  OCTET STRING SIZE(22)  

PnniPortId  
A PNNI port ID - this is used to identify a point of attachment of a logical link to a given logical node. The values 0 and 0xffffffff have special meanings in certain contexts and do not identify a specific port. The distinguished value 0 indicates that no port is specified.
TEXTUAL-CONVENTION    
  Unsigned32  

PnniAggrToken  
A PNNI aggregation token - this is used to determine which links to a given neighbor node are to be aggregated and advertised as a single logical link.
TEXTUAL-CONVENTION    
  Unsigned32  

PnniPeerGroupId  
A PNNI peer group ID.
TEXTUAL-CONVENTION    
  OCTET STRING SIZE(14)  

PnniLevel  
A PNNI routing level indicator.
TEXTUAL-CONVENTION    
  Integer32 0..104  

PnniSvccRccIndex  
The value of this object identifies the SVCC-based RCC for which the entry contains management information.
TEXTUAL-CONVENTION    
  Integer32  

AtmAddrPrefix  
A prefix of one or more ATM End System Addresses. The significant portion of a prefix is padded with zeros on the right to fill 19 octets.
TEXTUAL-CONVENTION    
  OCTET STRING SIZE(19)  

PnniPrefixLength  
The number of bits that are significant in an ATM address prefix used by PNNI.
TEXTUAL-CONVENTION    
  Integer32 0..152  

PnniMetricsTag  
An index into the pnniMetricsTable. The suffix tag is used to indicate that there may be many related entries in the table further discriminated by other index terms. The distinguished value zero indicates that no metrics are associated with the described entity.
TEXTUAL-CONVENTION    
  Integer32 0..2147483647  

ServiceCategory  
Indicates the service category.
TEXTUAL-CONVENTION    
  INTEGER other(1), cbr(2), rtVbr(3), nrtVbr(4), abr(5), ubr(6)  

ClpType  
Indicates the CLP type of a traffic stream.
TEXTUAL-CONVENTION    
  INTEGER clpEqual0(1), clpEqual0Or1(2)  

TnsType  
Indicates the type of network identification of a specified transit network.
TEXTUAL-CONVENTION    
  INTEGER nationalNetworkIdentification(2), other(8)  

TnsPlan  
Indicates the network identification plan of a specified transit network.
TEXTUAL-CONVENTION    
  INTEGER carrierIdentificationCode(1), other(16)  

PnniVersion  
Indicates a version of the PNNI protocol.
TEXTUAL-CONVENTION    
  INTEGER unsupported(1), version1point0(2)  

PnniHelloState  
The state of an instance of the PNNI Hello State machine.
TEXTUAL-CONVENTION    
  INTEGER notApplicable(1), down(2), attempt(3), oneWayInside(4), twoWayInside(5), oneWayOutside(6), twoWayOutside(7), commonOutside(8)  

PnniNodeEntry  
SEQUENCE    
  PnniNodeIndex as pnniNodeIndex  
  PnniLevel as pnniNodeLevel  
  PnniNodeId as pnniNodeId  
  TruthValue as pnniNodeLowest  
  INTEGER as pnniNodeAdminStatus  
  INTEGER as pnniNodeOperStatus  
  DisplayString as pnniNodeDomainName  
  PnniAtmAddr as pnniNodeAtmAddress  
  PnniPeerGroupId as pnniNodePeerGroupId  
  TruthValue as pnniNodeRestrictedTransit  
  TruthValue as pnniNodeComplexRep  
  TruthValue as pnniNodeRestrictedBranching  
  TruthValue as pnniNodeDatabaseOverload  
  Gauge32 as pnniNodePtses  
  RowStatus as pnniNodeRowStatus  

PnniNodePglEntry  
SEQUENCE    
  INTEGER as pnniNodePglLeadershipPriority  
  PnniNodeIndex as pnniNodeCfgParentNodeIndex  
  Integer32 as pnniNodePglInitTime  
  Integer32 as pnniNodePglOverrideDelay  
  Integer32 as pnniNodePglReelectTime  
  INTEGER as pnniNodePglState  
  PnniNodeId as pnniNodePreferredPgl  
  PnniNodeId as pnniNodePeerGroupLeader  
  TimeStamp as pnniNodePglTimeStamp  
  PnniNodeId as pnniNodeActiveParentNodeId  

PnniNodeTimerEntry  
SEQUENCE    
  Integer32 as pnniNodePtseHolddown  
  Integer32 as pnniNodeHelloHolddown  
  Integer32 as pnniNodeHelloInterval  
  Integer32 as pnniNodeHelloInactivityFactor  
  Integer32 as pnniNodeHlinkInact  
  Integer32 as pnniNodePtseRefreshInterval  
  INTEGER as pnniNodePtseLifetimeFactor  
  Integer32 as pnniNodeRxmtInterval  
  Integer32 as pnniNodePeerDelayedAckInterval  
  INTEGER as pnniNodeAvcrPm  
  INTEGER as pnniNodeAvcrMt  
  INTEGER as pnniNodeCdvPm  
  INTEGER as pnniNodeCtdPm  

PnniNodeSvccEntry  
SEQUENCE    
  Integer32 as pnniNodeSvccInitTime  
  Integer32 as pnniNodeSvccRetryTime  
  Integer32 as pnniNodeSvccCallingIntegrityTime  
  Integer32 as pnniNodeSvccCalledIntegrityTime  
  AtmTrafficDescrParamIndex as pnniNodeSvccTrafficDescriptorIndex  

PnniScopeMappingEntry  
SEQUENCE    
  PnniLevel as pnniScopeLocalNetwork  
  PnniLevel as pnniScopeLocalNetworkPlusOne  
  PnniLevel as pnniScopeLocalNetworkPlusTwo  
  PnniLevel as pnniScopeSiteMinusOne  
  PnniLevel as pnniScopeIntraSite  
  PnniLevel as pnniScopeSitePlusOne  
  PnniLevel as pnniScopeOrganizationMinusOne  
  PnniLevel as pnniScopeIntraOrganization  
  PnniLevel as pnniScopeOrganizationPlusOne  
  PnniLevel as pnniScopeCommunityMinusOne  
  PnniLevel as pnniScopeIntraCommunity  
  PnniLevel as pnniScopeCommunityPlusOne  
  PnniLevel as pnniScopeRegional  
  PnniLevel as pnniScopeInterRegional  
  PnniLevel as pnniScopeGlobal  

PnniSummaryEntry  
SEQUENCE    
  AtmAddrPrefix as pnniSummaryAddress  
  PnniPrefixLength as pnniSummaryPrefixLength  
  INTEGER as pnniSummaryType  
  TruthValue as pnniSummarySuppress  
  INTEGER as pnniSummaryState  
  RowStatus as pnniSummaryRowStatus  

PnniSummaryAddressEntry  
SEQUENCE    
  INTEGER as pnniSummaryAddressType  
  AtmAddrPrefix as pnniSummaryAddressAddress  
  PnniPrefixLength as pnniSummaryAddressPrefixLength  
  TruthValue as pnniSummaryAddressSuppress  
  INTEGER as pnniSummaryAddressState  
  RowStatus as pnniSummaryAddressRowStatus  

PnniIfEntry  
SEQUENCE    
  PnniNodeIndex as pnniIfNodeIndex  
  PnniPortId as pnniIfPortId  
  PnniAggrToken as pnniIfAggrToken  
  TruthValue as pnniIfVPCapability  
  Unsigned32 as pnniIfAdmWeightCbr  
  Unsigned32 as pnniIfAdmWeightRtVbr  
  Unsigned32 as pnniIfAdmWeightNrtVbr  
  Unsigned32 as pnniIfAdmWeightAbr  
  Unsigned32 as pnniIfAdmWeightUbr  
  ServiceCategory as pnniIfRccServiceCategory  
  AtmTrafficDescrParamIndex as pnniIfRccTrafficDescrIndex  

PnniLinkEntry  
SEQUENCE    
  PnniPortId as pnniLinkPortId  
  INTEGER as pnniLinkType  
  PnniVersion as pnniLinkVersion  
  PnniHelloState as pnniLinkHelloState  
  PnniNodeId as pnniLinkRemoteNodeId  
  PnniPortId as pnniLinkRemotePortId  
  PnniAggrToken as pnniLinkDerivedAggrToken  
  PnniNodeId as pnniLinkUpnodeId  
  PnniAtmAddr as pnniLinkUpnodeAtmAddress  
  PnniPeerGroupId as pnniLinkCommonPeerGroupId  
  InterfaceIndex as pnniLinkIfIndex  
  PnniSvccRccIndex as pnniLinkSvccRccIndex  
  Counter32 as pnniLinkRcvHellos  
  Counter32 as pnniLinkXmtHellos  

PnniNbrPeerEntry  
SEQUENCE    
  PnniNodeId as pnniNbrPeerRemoteNodeId  
  INTEGER as pnniNbrPeerState  
  PnniSvccRccIndex as pnniNbrPeerSvccRccIndex  
  Gauge32 as pnniNbrPeerPortCount  
  Counter32 as pnniNbrPeerRcvDbSums  
  Counter32 as pnniNbrPeerXmtDbSums  
  Counter32 as pnniNbrPeerRcvPtsps  
  Counter32 as pnniNbrPeerXmtPtsps  
  Counter32 as pnniNbrPeerRcvPtseReqs  
  Counter32 as pnniNbrPeerXmtPtseReqs  
  Counter32 as pnniNbrPeerRcvPtseAcks  
  Counter32 as pnniNbrPeerXmtPtseAcks  

PnniNbrPeerPortEntry  
SEQUENCE    
  PnniPortId as pnniNbrPeerPortId  
  TruthValue as pnniNbrPeerPortFloodStatus  

PnniSvccRccEntry  
SEQUENCE    
  PnniSvccRccIndex as pnniSvccRccIndex  
  PnniVersion as pnniSvccRccVersion  
  PnniHelloState as pnniSvccRccHelloState  
  PnniNodeId as pnniSvccRccRemoteNodeId  
  PnniAtmAddr as pnniSvccRccRemoteAtmAddress  
  Counter32 as pnniSvccRccRcvHellos  
  Counter32 as pnniSvccRccXmtHellos  
  InterfaceIndex as pnniSvccRccIfIndex  
  INTEGER as pnniSvccRccVpi  
  INTEGER as pnniSvccRccVci  

PnniPtseEntry  
SEQUENCE    
  PnniNodeId as pnniPtseOriginatingNodeId  
  Unsigned32 as pnniPtseId  
  INTEGER as pnniPtseType  
  Unsigned32 as pnniPtseSequenceNum  
  Unsigned32 as pnniPtseChecksum  
  Unsigned32 as pnniPtseLifeTime  
  OCTET STRING as pnniPtseInfo  

PnniMapEntry  
SEQUENCE    
  PnniNodeId as pnniMapOriginatingNodeId  
  PnniPortId as pnniMapOriginatingPortId  
  INTEGER as pnniMapIndex  
  INTEGER as pnniMapType  
  PnniPeerGroupId as pnniMapPeerGroupId  
  PnniAggrToken as pnniMapAggrToken  
  PnniNodeId as pnniMapRemoteNodeId  
  PnniPortId as pnniMapRemotePortId  
  TruthValue as pnniMapVPCapability  
  Unsigned32 as pnniMapPtseId  
  PnniMetricsTag as pnniMapMetricsTag  

PnniMapNodeEntry  
SEQUENCE    
  PnniNodeId as pnniMapNodeId  
  PnniPeerGroupId as pnniMapNodePeerGroupId  
  PnniAtmAddr as pnniMapNodeAtmAddress  
  TruthValue as pnniMapNodeRestrictedTransit  
  TruthValue as pnniMapNodeComplexRep  
  TruthValue as pnniMapNodeRestrictedBranching  
  TruthValue as pnniMapNodeDatabaseOverload  
  TruthValue as pnniMapNodeIAmLeader  
  INTEGER as pnniMapNodeLeadershipPriority  
  PnniNodeId as pnniMapNodePreferredPgl  
  PnniNodeId as pnniMapNodeParentNodeId  
  PnniAtmAddr as pnniMapNodeParentAtmAddress  
  PnniPeerGroupId as pnniMapNodeParentPeerGroupId  
  PnniNodeId as pnniMapNodeParentPglNodeId  

PnniMapAddrEntry  
SEQUENCE    
  PnniNodeId as pnniMapAddrAdvertisingNodeId  
  PnniPortId as pnniMapAddrAdvertisedPortId  
  INTEGER as pnniMapAddrIndex  
  AtmAddrPrefix as pnniMapAddrAddress  
  PnniPrefixLength as pnniMapAddrPrefixLength  

PnniMapTnsEntry  
SEQUENCE    
  PnniNodeId as pnniMapTnsAdvertisingNodeId  
  PnniPortId as pnniMapTnsAdvertisedPortId  
  TnsType as pnniMapTnsType  
  TnsPlan as pnniMapTnsPlan  
  DisplayString as pnniMapTnsId  

PnniMetricsEntry  
SEQUENCE    
  PnniMetricsTag as pnniMetricsTag  
  INTEGER as pnniMetricsDirection  
  Integer32 as pnniMetricsIndex  
  INTEGER as pnniMetricsClasses  
  ClpType as pnniMetricsGcacClp  
  Unsigned32 as pnniMetricsAdminWeight  
  Unsigned32 as pnniMetrics1  
  Unsigned32 as pnniMetrics2  
  Unsigned32 as pnniMetrics3  
  Unsigned32 as pnniMetrics4  
  Unsigned32 as pnniMetrics5  
  Unsigned32 as pnniMetrics6  
  Unsigned32 as pnniMetrics7  
  Unsigned32 as pnniMetrics8  
  RowStatus as pnniMetricsRowStatus  

PnniRouteNodeEntry  
SEQUENCE    
  ServiceCategory as pnniRouteNodeClass  
  PnniNodeId as pnniRouteNodeDestNodeId  
  Integer32 as pnniRouteNodeDTL  
  PnniPortId as pnniRouteNodeDestPortId  
  INTEGER as pnniRouteNodeProto  
  TimeStamp as pnniRouteNodeTimeStamp  
  OBJECT IDENTIFIER as pnniRouteNodeInfo  
  ClpType as pnniRouteNodeGcacClp  
  Unsigned32 as pnniRouteNodeFwdMetricAW  
  Unsigned32 as pnniRouteNodeFwdMetric1  
  Unsigned32 as pnniRouteNodeFwdMetric2  
  Unsigned32 as pnniRouteNodeFwdMetric3  
  Unsigned32 as pnniRouteNodeFwdMetric4  
  Unsigned32 as pnniRouteNodeFwdMetric5  
  Unsigned32 as pnniRouteNodeFwdMetric6  
  Unsigned32 as pnniRouteNodeFwdMetric7  
  Unsigned32 as pnniRouteNodeFwdMetric8  
  Unsigned32 as pnniRouteNodeBwdMetricAW  
  Unsigned32 as pnniRouteNodeBwdMetric1  
  Unsigned32 as pnniRouteNodeBwdMetric2  
  Unsigned32 as pnniRouteNodeBwdMetric3  
  Unsigned32 as pnniRouteNodeBwdMetric4  
  Unsigned32 as pnniRouteNodeBwdMetric5  
  Unsigned32 as pnniRouteNodeBwdMetric6  
  Unsigned32 as pnniRouteNodeBwdMetric7  
  Unsigned32 as pnniRouteNodeBwdMetric8  
  TruthValue as pnniRouteNodeVPCapability  
  RowStatus as pnniRouteNodeStatus  

PnniDTLEntry  
SEQUENCE    
  Integer32 as pnniDTLIndex  
  Integer32 as pnniDTLEntryIndex  
  PnniNodeId as pnniDTLNodeId  
  PnniPortId as pnniDTLPortId  
  INTEGER as pnniDTLLinkType  
  RowStatus as pnniDTLStatus  

PnniRouteAddrEntry  
SEQUENCE    
  AtmAddrPrefix as pnniRouteAddrAddress  
  PnniPrefixLength as pnniRouteAddrPrefixLength  
  Integer32 as pnniRouteAddrIndex  
  InterfaceIndex as pnniRouteAddrIfIndex  
  PnniNodeId as pnniRouteAddrAdvertisingNodeId  
  PnniPortId as pnniRouteAddrAdvertisedPortId  
  INTEGER as pnniRouteAddrType  
  INTEGER as pnniRouteAddrProto  
  PnniLevel as pnniRouteAddrPnniScope  
  TruthValue as pnniRouteAddrVPCapability  
  PnniMetricsTag as pnniRouteAddrMetricsTag  
  Unsigned32 as pnniRouteAddrPtseId  
  TruthValue as pnniRouteAddrOriginateAdvertisement  
  OBJECT IDENTIFIER as pnniRouteAddrInfo  
  INTEGER as pnniRouteAddrOperStatus  
  TimeStamp as pnniRouteAddrTimeStamp  
  RowStatus as pnniRouteAddrRowStatus  

PnniRouteTnsEntry  
SEQUENCE    
  TnsType as pnniRouteTnsType  
  TnsPlan as pnniRouteTnsPlan  
  DisplayString as pnniRouteTnsId  
  Integer32 as pnniRouteTnsIndex  
  InterfaceIndex as pnniRouteTnsIfIndex  
  PnniNodeId as pnniRouteTnsAdvertisingNodeId  
  PnniPortId as pnniRouteTnsAdvertisedPortId  
  INTEGER as pnniRouteTnsRouteType  
  INTEGER as pnniRouteTnsProto  
  PnniLevel as pnniRouteTnsPnniScope  
  TruthValue as pnniRouteTnsVPCapability  
  PnniMetricsTag as pnniRouteTnsMetricsTag  
  Unsigned32 as pnniRouteTnsPtseId  
  TruthValue as pnniRouteTnsOriginateAdvertisement  
  OBJECT IDENTIFIER as pnniRouteTnsInfo  
  INTEGER as pnniRouteTnsOperStatus  
  TimeStamp as pnniRouteTnsTimeStamp  
  RowStatus as pnniRouteTnsRowStatus