PORT-MIB

File: PORT-MIB.mib (81595 bytes)

Imported modules

RFC1155-SMI SNMPv2-SMI CORIOLIS-MIB
CARD-MIB IF-MIB EtherLike-MIB
MAU-MIB SONET-MIB SNMPv2-TC
RFC-1215

Imported symbols

Counter Unsigned32 OBJECT-TYPE
MODULE-IDENTITY Integer32 Counter32
Counter64 port coriolisMibs
slotNo ifAdminStatus ifOperStatus
ifSpeed InterfaceIndex dot3StatsDuplexStatus
ifMauAutoNegConfig sonetSectionCurrentStatus sonetLineCurrentStatus
sonetPathCurrentStatus sonetVTCurrentStatus TruthValue
TRAP-TYPE

Defined Objects

portPhyStatusChange 1.3.6.1.4.1.5812.0
Change in the operational status of a port, 1 means the port came up, 2 means it went down
TRAP-TYPE    
  ifOperStatus  

portAdminStatusChange 1.3.6.1.4.1.5812.1
Change in the admin status of a port, 1 means the port came up, 2 means it went down
TRAP-TYPE    
  ifAdminStatus  

portMIB 1.3.6.1.4.1.5812.3.1
The MIB module for cards in coriolis boxes
MODULE-IDENTITY    

portTable 1.3.6.1.4.1.5812.3.2
The port table. This contains the portNo variable, which is used as an index into specific port tables
OBJECT-TYPE    
  SEQUENCE OF  
    PortEntry

portEntry 1.3.6.1.4.1.5812.3.2.1
Entry containing the portNo variable
OBJECT-TYPE    
  PortEntry  

portNo 1.3.6.1.4.1.5812.3.2.1.1
The purpose of this variable is to be used as index into tables
OBJECT-TYPE    
  INTEGER 1..16  

mib2IfIndex 1.3.6.1.4.1.5812.3.2.1.2
This variable serves to identify the slot and port number.
OBJECT-TYPE    
  InterfaceIndex  

etherPortTable 1.3.6.1.4.1.5812.3.3
The ethernet port table. This table contains information about the ethernet ports in this device.
OBJECT-TYPE    
  SEQUENCE OF  
    EtherPortEntry

etherPortEntry 1.3.6.1.4.1.5812.3.3.1
Entry containing information about ethernet ports
OBJECT-TYPE    
  EtherPortEntry  

etherPortSpeedCfg 1.3.6.1.4.1.5812.3.3.1.1
The desired port speed if Autonegotiation is disabled. Management control of the port speed can also be accomplished through the MAU MIB via ifMauDefaultType. Note that this object provides redundant information with ifMauType. Normally, redundant objects are discouraged. However, in this instance, it allows a management application to configure the duplex mode of an interface without having to know every possible value of ifMauType. This was felt to be sufficiently valuable to justify the redundancy.
OBJECT-TYPE    
  INTEGER speed10(1), speed100(2), speed1000(3)  

etherPortSpeedStatus 1.3.6.1.4.1.5812.3.3.1.2
The speed of the port. If autoneg is enabled, this is determined by the results of the autoneg process. If autoneg is disabled, this is the same as IfAdminSpeed.
OBJECT-TYPE    
  INTEGER speed10(1), speed100(2), speed1000(3)  

etherPortDuplexCfg 1.3.6.1.4.1.5812.3.3.1.3
The desired duplex mode of operation of the MAC entity if Autonegotiation is disabled. Management control of the duplex mode can also be accomplished through the MAU MIB via ifMauDefaultType.Note that this object provides redundant information with ifMauType. Normally, redundant objects are discouraged. However, in this instance, it allows a management application to configure the duplex mode of an interface without having to know every possible value of ifMauType. This was felt to be sufficiently valuable to justify the redundancy.
OBJECT-TYPE    
  INTEGER unknown(1), half(2), full(3)  

etherPortLoopback 1.3.6.1.4.1.5812.3.3.1.4
Enables/disables loopback mode.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

etherPortPhyReset 1.3.6.1.4.1.5812.3.3.1.5
Ethernet port phy reset
OBJECT-TYPE    
  INTEGER inReset(1), outOfReset(2)  

etherPortStatsTxPkts64Octets 1.3.6.1.4.1.5812.3.3.1.6
Total 64 byte packets transmitted on ethernet port.
OBJECT-TYPE    
  Counter  

etherPortStatsTxPkts65to127Octets 1.3.6.1.4.1.5812.3.3.1.7
The total number of packets (including bad packets) transmitted that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).
OBJECT-TYPE    
  Counter  

etherPortStatsTxPkts128to255Octets 1.3.6.1.4.1.5812.3.3.1.8
The total number of packets (including bad packets) transmitted that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).
OBJECT-TYPE    
  Counter  

etherPortStatsTxPkts256to511Octets 1.3.6.1.4.1.5812.3.3.1.9
The total number of packets (including bad packets) transmitted that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).
OBJECT-TYPE    
  Counter  

etherPortStatsTxPkts512to1023Octets 1.3.6.1.4.1.5812.3.3.1.10
The total number of packets (including bad packets) transmitted that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).
OBJECT-TYPE    
  Counter  

etherPortStatsTxPkts1024to1518Octets 1.3.6.1.4.1.5812.3.3.1.11
The total number of packets (including bad packets) transmitted that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).
OBJECT-TYPE    
  Counter  

etherPortStatsTxPkts1519to1530Octets 1.3.6.1.4.1.5812.3.3.1.12
The total number of packets (including bad packets) transmitted that were between 1519 and 1530 octets in length inclusive (excluding framing bits but including FCS octets).
OBJECT-TYPE    
  Counter  

etherPortStatsTxFCSErrors 1.3.6.1.4.1.5812.3.3.1.13
Total packets transmitted on ethernet port with FCS errors (if MAC generates the FCS, this can never be incremented).
OBJECT-TYPE    
  Counter  

etherPortStatsTxOversize 1.3.6.1.4.1.5812.3.3.1.14
Number of frames transmitted greater than 1518 bytes.
OBJECT-TYPE    
  Counter  

etherPortStatsTxUndersize 1.3.6.1.4.1.5812.3.3.1.15
Number of packets less than 64 bytes transmitted.
OBJECT-TYPE    
  Counter  

etherPortStatsTxControlFrames 1.3.6.1.4.1.5812.3.3.1.16
Number of control frames transmitted.
OBJECT-TYPE    
  Counter  

etherPortStatsTxBadFifoUnderrun 1.3.6.1.4.1.5812.3.3.1.17
Number of bad frames (due to Transmit FIFO underrun) transmitted.
OBJECT-TYPE    
  Counter  

etherPortStatsTxBadFifoOverrun 1.3.6.1.4.1.5812.3.3.1.18
Number of bad frames (due to Transmit FIFO overrun) transmitted.
OBJECT-TYPE    
  Counter  

etherPortStatsTxDropFifoOverrun 1.3.6.1.4.1.5812.3.3.1.19
Number of frames dropped due to Transmit FIFO underrun.
OBJECT-TYPE    
  Counter  

etherPortStatsTxBadParityError 1.3.6.1.4.1.5812.3.3.1.20
Number of bad frames (due to parity error) transmitted.
OBJECT-TYPE    
  Counter  

etherPortStatsTxDropParityError 1.3.6.1.4.1.5812.3.3.1.21
Number of bad frames (due to parity error) dropped.
OBJECT-TYPE    
  Counter  

etherPortStatsTxBadSequenceError 1.3.6.1.4.1.5812.3.3.1.22
Number of bad frames (due to frame Sequence Error) transmitted.
OBJECT-TYPE    
  Counter  

etherPortStatsTxDropSequenceError 1.3.6.1.4.1.5812.3.3.1.23
Number of bad frames (due to frame Sequence Error) dropped.
OBJECT-TYPE    
  Counter  

etherPortStatsTxBadJamError 1.3.6.1.4.1.5812.3.3.1.24
Number of bad frames (due to Jam Bit Error) transmitted.
OBJECT-TYPE    
  Counter  

etherPortStatsTxDropJamError 1.3.6.1.4.1.5812.3.3.1.25
Number of bad frames (due to Jam Bit Error) dropped.
OBJECT-TYPE    
  Counter  

etherPortSpeedTrapEnable 1.3.6.1.4.1.5812.3.3.1.26
Indicates whether portSpeedTrap traps should be generated for this interface.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

etherPortDuplexTrapEnable 1.3.6.1.4.1.5812.3.3.1.27
Ethernet port duplex trap enable
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

etherPortAutonegTrapEnable 1.3.6.1.4.1.5812.3.3.1.28
Indicates whether autoNegCompleteTrap traps should be generated for this interface.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

etherPortRowStatus 1.3.6.1.4.1.5812.3.3.1.29
This variable is used to create or delete instances of ethernet ports This variable subsumes the admin state variable, and once the row is created, its value returns the admin state of the port
OBJECT-TYPE    
  INTEGER active(1), notInService(2), createAndGo(4), createAndWait(5), destroy(6)  

etherPortAutonegAdvSpeed 1.3.6.1.4.1.5812.3.3.1.30
This specifies what speed capability is advertised for autonegotiation. If 100 MBPS is set, then 10 MBPS is also advertised.This does not apply to Gig Ethernet Phys, since they do not autonegotiate speed or duplex.
OBJECT-TYPE    
  INTEGER speed10(1), speed100(2), speed1000(3)  

etherPortAutonegAdvDuplex 1.3.6.1.4.1.5812.3.3.1.31
This specifies what duplex capability is advertised for autonegotiation. If Full Duplex is set, then Half Duplex is also adveetised.This does not apply to Gig Ethernet Phys, since they do not autonegotiate speed or duplex.
OBJECT-TYPE    
  INTEGER unknown(1), half(2), full(3)  

etherPortPauseStateReceived 1.3.6.1.4.1.5812.3.3.1.32
The PAUSE mode received from the remote device, as read from the Auto Negotiation Partner Ability GMII Register of the PHY.If autoNegotiation is not enabled and completed, then this is set to undefined. This is used to determine the dot3PauseOperMode for the interface.
OBJECT-TYPE    
  INTEGER noPause(1), enableTx(2), enableRx(3), enableTxRx(4), undefined(5)  

etherPortVlanMode 1.3.6.1.4.1.5812.3.3.1.33
Specifies the VLAN mode for the port
OBJECT-TYPE    
  INTEGER enabled(1), stripVID(2), transparent(3)  

etherPortDefaultVlanId 1.3.6.1.4.1.5812.3.3.1.34
Specifies what the default Vlan Id is for the port. This is used on ingress only if vlanMode is Enabled and a frame is received either untagged or tagged with a VID not known to the port.
OBJECT-TYPE    
  INTEGER  

etherPortRxOverrun 1.3.6.1.4.1.5812.3.3.1.35
The total number of packets dropped by the GMAC due to the occurence of a receive overrun (gig only- supported by GMAC-D2 and later)
OBJECT-TYPE    
  Counter  

etherPortRxSyncErrors 1.3.6.1.4.1.5812.3.3.1.36
The total number of packets dropped due to loss of sync during packet reception. (GIG only- supported by GMAC-D2 and later)
OBJECT-TYPE    
  Counter  

etherPortRxDelSeqErrors 1.3.6.1.4.1.5812.3.3.1.37
The total number of packets dropped due to delimiter sequence errors as detected by the GMAC during packet reception. (GIG only- supported by GMAC-D2 and later)
OBJECT-TYPE    
  Counter  

etherPortRxFifoOverrunErrors 1.3.6.1.4.1.5812.3.3.1.38
The total number of packets dropped by the GMAC due to the occurence of a receive FIFO overrun (gig only- supported by GMAC-D2 and later)
OBJECT-TYPE    
  Counter  

etherPortRxControlFrames 1.3.6.1.4.1.5812.3.3.1.39
Number of control frames received by this port
OBJECT-TYPE    
  Counter  

etherPortRxThreshOvrszFrames 1.3.6.1.4.1.5812.3.3.1.40
The total number of threshold oversized frames received by the GMAC (gig only - supported by GMAC-D2 and later)
OBJECT-TYPE    
  Counter  

etherPortStatsRxPkts1519to1530Octets 1.3.6.1.4.1.5812.3.3.1.41
The total number of packets (including bad packets) received that were between 1519 and 1530 octets in length inclusive (excluding framing bits but including FCS octets).
OBJECT-TYPE    
  Counter  

tdmIoDS1PortTable 1.3.6.1.4.1.5812.3.4
The DS1 TDM IO Port Table
OBJECT-TYPE    
  SEQUENCE OF  
    TdmIoDS1PortEntry

tdmIoDS1PortEntry 1.3.6.1.4.1.5812.3.4.1
Entry containing information about TDM IO DS1 ports
OBJECT-TYPE    
  TdmIoDS1PortEntry  

tdmIoDS1PortType 1.3.6.1.4.1.5812.3.4.1.1
The type of TDM IO DS1 port
OBJECT-TYPE    
  INTEGER ds1(1)  

tdmIoDS1PortTiming 1.3.6.1.4.1.5812.3.4.1.2
Clock source for the DS1 port 'loopTiming' indicates that the recovered re- ceive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' indicates that recovered re- ceive clock from another interface is used as the transmit clock.
OBJECT-TYPE    
  INTEGER loopTiming(1), localTiming(2), throughTiming(3)  

tdmIoDS1PortBuildOut 1.3.6.1.4.1.5812.3.4.1.5
Line Build Out for Signal Strength. For short haul, a distance (in feet) is chosen. For long haul, an attenuation strength is chosen in Decibels.
OBJECT-TYPE    
  INTEGER shortHaulMax133Feet(1), shortHaulMax266Feet(2), shortHaulMax399Feet(3), shortHaulMax533Feet(4), shortHaulMax655Feet(5), longHaulZeroDB(6), longHaulSevenFiveDB(7), longHaulOneFiveDB(8), longHaulTwentyTwoDB(9)  

tdmIoDS1PortFraming 1.3.6.1.4.1.5812.3.4.1.6
Framing type implemented for this interface.
OBJECT-TYPE    
  INTEGER ds1unframed(1)  

tdmIoDS1PortCoding 1.3.6.1.4.1.5812.3.4.1.7
The type of Zero Code Suppression used on this interface. B8ZS refers to the use of a specified pattern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits. AMI refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density requirements, such as inverting HDLC data.
OBJECT-TYPE    
  INTEGER b8zs(2), ami(5)  

tdmIoDS1PortLoopbackState 1.3.6.1.4.1.5812.3.4.1.8
This object indicates the state of loopback on this interface. 'Idle' indicates that there is no loopback running and 'running' indicates that this interface is in loopback mode.
OBJECT-TYPE    
  INTEGER idle(1), running(2)  

tdmIoDS1PortLoopbackType 1.3.6.1.4.1.5812.3.4.1.9
This object indicates the type of loopback on this interface. noLoop - the interface is not in loopBack mode. localOn - the interface is running in internal loop. digitalOn - the interface is running in internal loop. remoteOn - the interface is looping away external data.
OBJECT-TYPE    
  INTEGER noLoop(1), localOn(8), digitalOn(9), remoteOn(10)  

tdmIoDS1PortLoopbackResults 1.3.6.1.4.1.5812.3.4.1.10
Results from previous loopback on this port
OBJECT-TYPE    
  INTEGER failure(1), success(2)  

tdmIoDS1PortLoopbackLLbActCode 1.3.6.1.4.1.5812.3.4.1.11
User code to enable Automatic Remote Loopback(ARL)
OBJECT-TYPE    
  INTEGER  

tdmIoDS1PortLoopbackLLbDeactCode 1.3.6.1.4.1.5812.3.4.1.12
User code to disable Automatic Remote Loopback(ARL)
OBJECT-TYPE    
  INTEGER  

tdmIoDS1PortLoopbackLlbActCodeLen 1.3.6.1.4.1.5812.3.4.1.13
Length of user code to enable Automatic Remote Loopback(ARL)
OBJECT-TYPE    
  INTEGER up5Bit(1), up6Bit(2), up7Bit(3), up8Bit(4)  

tdmIoDS1PortLoopbackLlbDeactCodeLen 1.3.6.1.4.1.5812.3.4.1.14
Length of user code to disable Automatic Remote Loopback(ARL)
OBJECT-TYPE    
  INTEGER down5Bit(1), down6Bit(2), down7Bit(3), down8Bit(4)  

tdmIoDS1PortLoopbackLlbControl 1.3.6.1.4.1.5812.3.4.1.15
LLBCODE(activate/deactivate) generation/monitoring control
OBJECT-TYPE    
  INTEGER genOff(1), genActOn(2), genDeActOn(3), monOff(4), monOn(5)  

tdmIoDS1PortLoopbackLlbGenPath 1.3.6.1.4.1.5812.3.4.1.16
The path (xmit/rcv) for LLBCODE generation
OBJECT-TYPE    
  INTEGER genRcv(1), genXmit(2)  

tdmIoDS1PortLoopbackLlbMonPath 1.3.6.1.4.1.5812.3.4.1.17
The path (xmit/rcv) for LLBCODE monitoring
OBJECT-TYPE    
  INTEGER monRcv(1), monXmit(2)  

tdmIoDS1PortPrbsAlgorithm 1.3.6.1.4.1.5812.3.4.1.18
The PRBS Algorithm
OBJECT-TYPE    
  INTEGER algo215(1), algo220(2)  

tdmIoDS1PortPrbsInversion 1.3.6.1.4.1.5812.3.4.1.19
Whether the PRBS stream will be inverted
OBJECT-TYPE    
  INTEGER off(1), on(2)  

tdmIoDS1PortPrbsGenPath 1.3.6.1.4.1.5812.3.4.1.20
The PRBS generator path
OBJECT-TYPE    
  INTEGER genRcv(1), genXmit(2)  

tdmIoDS1PortPrbsMonPath 1.3.6.1.4.1.5812.3.4.1.21
The PRBS monitor path
OBJECT-TYPE    
  INTEGER monRcv(1), monXmit(2)  

tdmIoDS1PortPrbsMonitor 1.3.6.1.4.1.5812.3.4.1.22
PRBS monitor - is it off or on?
OBJECT-TYPE    
  INTEGER off(1), on(2)  

tdmIoDS1PortPrbsTransmit 1.3.6.1.4.1.5812.3.4.1.23
PRBS or normal transmission on transmission line
OBJECT-TYPE    
  INTEGER off(1), on(2)  

tdmIoDS1PortPrbsBec 1.3.6.1.4.1.5812.3.4.1.24
The PRBS bit error counter
OBJECT-TYPE    
  Counter  

tdmIoDS1PortBertState 1.3.6.1.4.1.5812.3.4.1.25
User specified BERT status
OBJECT-TYPE    
  INTEGER idle(1), running(2), other(3)  

tdmIoDS1PortBertPattern 1.3.6.1.4.1.5812.3.4.1.26
User specified BERT type
OBJECT-TYPE    
  INTEGER pattern223(1), pattern220(2), patternQrss(3), pattern215(4), pattern211(5), patternAllZeros(6), patternAllOnes(7), patternAlternate(8)  

tdmIoDS1PortBertDuration 1.3.6.1.4.1.5812.3.4.1.27
User specified BERT duration
OBJECT-TYPE    
  INTEGER oneMin(1), fiveMin(2), thirtyMin(3), oneHour(4), twelveHour(5), twentyfourHour(6)  

tdmIoDS1PortBertResults 1.3.6.1.4.1.5812.3.4.1.28
Results from previous BERT test on this port
OBJECT-TYPE    
  INTEGER timeLeft(1), totalBitErrs(2), totalBits(3)  

tdmIoDS1PortLineESS15Min 1.3.6.1.4.1.5812.3.4.1.29
The 15 minute Line Errored Seconds Threshold
OBJECT-TYPE    
  INTEGER 1..900  

tdmIoDS1PortPathESS15Min 1.3.6.1.4.1.5812.3.4.1.30
The 15 minute Path Errored Seconds Threshold
OBJECT-TYPE    
  INTEGER 1..900  

tdmIoDS1PortLineESS1Day 1.3.6.1.4.1.5812.3.4.1.31
The 1 Day Line Errored Seconds Threshold
OBJECT-TYPE    
  INTEGER 1..65535  

tdmIoDS1PortPathESS1Day 1.3.6.1.4.1.5812.3.4.1.32
The 1 Day Path Errored Seconds Threshold
OBJECT-TYPE    
  INTEGER 1..65535  

tdmIoDS1PortPathCVS15Min 1.3.6.1.4.1.5812.3.4.1.33
The 15 minute Path Coding Violations Threshold
OBJECT-TYPE    
  INTEGER 1..16383  

tdmIoDS1PortPathCVS1Day 1.3.6.1.4.1.5812.3.4.1.34
The 1 day Path Coding Violations Threshold
OBJECT-TYPE    
  INTEGER 1..1048575  

tdmIoDS1PortPathSESS15Min 1.3.6.1.4.1.5812.3.4.1.35
The 15 minute Path Severely Errored Seconds Threshold
OBJECT-TYPE    
  INTEGER 1..900  

tdmIoDS1PortPathSESS1Day 1.3.6.1.4.1.5812.3.4.1.36
The 1 day Path Severely Errored Seconds Threshold
OBJECT-TYPE    
  INTEGER 1..65535  

tdmIoDS1PortPathSASS15Min 1.3.6.1.4.1.5812.3.4.1.37
The 15 minute Path AIS seconds Threshold
OBJECT-TYPE    
  INTEGER 1..900  

tdmIoDS1PortPathSASS1Day 1.3.6.1.4.1.5812.3.4.1.38
The 1 day Path AIS seconds Threshold
OBJECT-TYPE    
  INTEGER 1..65535  

tdmIoDS1PortPathCSS15Min 1.3.6.1.4.1.5812.3.4.1.39
The 15 minute path controlled slip seconds threshold
OBJECT-TYPE    
  INTEGER 1..900  

tdmIoDS1PortPathCSS1Day 1.3.6.1.4.1.5812.3.4.1.40
The 1 day path controlled slip seconds threshold
OBJECT-TYPE    
  INTEGER 1..65535  

tdmIoDS1PortPathUASS15Min 1.3.6.1.4.1.5812.3.4.1.41
The 15 minute path unavailable seconds threshold
OBJECT-TYPE    
  INTEGER 1..900  

tdmIoDS1PortRowStatus 1.3.6.1.4.1.5812.3.4.1.42
This variable is used to create or delete instances of TDM IO DS1 ports. This variable subsumes the admin state variable, and once the row is created, its value returns the admin state of the port
OBJECT-TYPE    
  INTEGER active(1), notInService(2), createAndGo(4), createAndWait(5), destroy(6)  

dsxStatus 1.3.6.1.4.1.5812.3.4.1.43
DSx line status.
OBJECT-TYPE    
  INTEGER dsx-rcvrai-failure-declared(1), dsx-rcvrai-failure-cleared(2), dsx-xmitrai-failure-declared(3), dsx-xmitrai-failure-cleared(4), dsx-rcvais-failure-declared(5), dsx-rcvais-failure-cleared(6), dsx-xmitais-failure-declared(7), dsx-xmitais-failure-cleared(8), dsx-los-failure-declared(9), dsx-los-failure-cleared(10), dsx-lof-failure-declared(11), dsx-lof-failure-cleared(12), dsx-other-failure-declared(13), dsx-other-failure-cleared(14), dsx-uas-failure-declared(15), dsx-uas-failure-cleared(16), dsx-exz-failure-declared(17), dsx-exz-failure-cleared(18), dsx-pden-failure-declared(19), dsx-pden-failure-cleared(20)  

tdmIoDS1PortLCVCount 1.3.6.1.4.1.5812.3.4.1.44
Count of Line Code Violations.
OBJECT-TYPE    
  INTEGER  

sonetPortTable 1.3.6.1.4.1.5812.3.5
The proprietary SONET Port Table
OBJECT-TYPE    
  SEQUENCE OF  
    SonetPortEntry

sonetPortEntry 1.3.6.1.4.1.5812.3.5.1
Entry containing information about SONET ports
OBJECT-TYPE    
  SonetPortEntry  

sonetPortType 1.3.6.1.4.1.5812.3.5.1.1
The type of SONET port
OBJECT-TYPE    
  INTEGER oc12c(1), oc12sts1(2)  

sonetPortIdString 1.3.6.1.4.1.5812.3.5.1.2
The identifier string for the SONET port
OBJECT-TYPE    
  OCTET STRING  

sonetPortTiming 1.3.6.1.4.1.5812.3.5.1.3
Clock source for the port
OBJECT-TYPE    
  INTEGER internal(1), external(2)  

sonetPortLoopback 1.3.6.1.4.1.5812.3.5.1.4
The types of loopback available on the SONET interface.
OBJECT-TYPE    
  INTEGER slle(1), sdle(2), pdle(3), sllben(4), none(5)  

sonetPortScrambling 1.3.6.1.4.1.5812.3.5.1.5
Whether port scrambling is enabled or disabled
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sonetPortChannelization 1.3.6.1.4.1.5812.3.5.1.6
Whether the physical port is concatenated or not
OBJECT-TYPE    
  INTEGER concatenated(1), nonConcatenated(2)  

sonetPortConfigedChans 1.3.6.1.4.1.5812.3.5.1.7
The channels configured on the port
OBJECT-TYPE    
  Unsigned32  

sonetPortSectESS15Min 1.3.6.1.4.1.5812.3.5.1.8
15 minute section errored seconds threshold
OBJECT-TYPE    
  INTEGER 1..900  

sonetPortLineESS15Min 1.3.6.1.4.1.5812.3.5.1.9
15 minute line errored seconds threshold
OBJECT-TYPE    
  INTEGER 1..900  

sonetPortPathESS15Min 1.3.6.1.4.1.5812.3.5.1.10
15 minute path errored seconds threshold
OBJECT-TYPE    
  INTEGER 1..900  

sonetPortSectESS1Day 1.3.6.1.4.1.5812.3.5.1.11
1 day section errored seconds threshold
OBJECT-TYPE    
  INTEGER 1..65535  

sonetPortLineESS1Day 1.3.6.1.4.1.5812.3.5.1.12
1 day line errored seconds threshold
OBJECT-TYPE    
  INTEGER 1..65535  

sonetPortPathESS1Day 1.3.6.1.4.1.5812.3.5.1.13
1 day path errored seconds threshold
OBJECT-TYPE    
  INTEGER 1..65535  

sonetPortSectCVS15Min 1.3.6.1.4.1.5812.3.5.1.14
15 minute section coding violations threshold
OBJECT-TYPE    
  INTEGER 1..16383  

sonetPortLineCVS15Min 1.3.6.1.4.1.5812.3.5.1.15
15 minute line coding violations threshold
OBJECT-TYPE    
  INTEGER 1..16383  

sonetPortPathCVS15Min 1.3.6.1.4.1.5812.3.5.1.16
15 minutes path coding violations threshold
OBJECT-TYPE    
  INTEGER 1..16383  

sonetPortSectCVS1Day 1.3.6.1.4.1.5812.3.5.1.17
1 day section coding violations threshold
OBJECT-TYPE    
  INTEGER 1..1048575  

sonetPortLineCVS1Day 1.3.6.1.4.1.5812.3.5.1.18
1 day line coding violations threshold
OBJECT-TYPE    
  INTEGER 1..1048575  

sonetPortPathCVS1Day 1.3.6.1.4.1.5812.3.5.1.19
1 day path coding violations threshold
OBJECT-TYPE    
  INTEGER 1..1048575  

sonetPortSectSESS15Min 1.3.6.1.4.1.5812.3.5.1.20
15 minutes section severely errored seconds threshold
OBJECT-TYPE    
  INTEGER 1..900  

sonetPortLineSESS15Min 1.3.6.1.4.1.5812.3.5.1.21
15 minutes line severely errored seconds threshold
OBJECT-TYPE    
  INTEGER 1..900  

sonetPortPathSESS15Min 1.3.6.1.4.1.5812.3.5.1.22
15 minutes path severely errored seconds threshold
OBJECT-TYPE    
  INTEGER 1..900  

sonetPortSectSESS1Day 1.3.6.1.4.1.5812.3.5.1.23
1 day section severely errored seconds threshold
OBJECT-TYPE    
  INTEGER 1..65535  

sonetPortLineSESS1Day 1.3.6.1.4.1.5812.3.5.1.24
1 day line severely errored seconds threshold
OBJECT-TYPE    
  INTEGER 1..65535  

sonetPortPathSESS1Day 1.3.6.1.4.1.5812.3.5.1.25
1 day path severely errored seconds threshold
OBJECT-TYPE    
  INTEGER 1..65535  

sonetPortLineUASS15Min 1.3.6.1.4.1.5812.3.5.1.26
15 minutes line unavailable seconds threshold
OBJECT-TYPE    
  INTEGER 1..900  

sonetPortPathUASS15Min 1.3.6.1.4.1.5812.3.5.1.27
15 minutes path unavailable seconds threshold
OBJECT-TYPE    
  INTEGER 1..900  

sonetPortLineUASS1Day 1.3.6.1.4.1.5812.3.5.1.28
1 day line unavailable seconds threshold
OBJECT-TYPE    
  INTEGER 1..65535  

sonetPortPathUASS1Day 1.3.6.1.4.1.5812.3.5.1.29
1 day path unavailable seconds threshold
OBJECT-TYPE    
  INTEGER 1..65535  

sonetPortRowStatus 1.3.6.1.4.1.5812.3.5.1.30
This variable is used to create or delete instances of SONET ports This variable subsumes the admin state variable, and once the row is created, its value returns the admin state of the port
OBJECT-TYPE    
  INTEGER active(1), notInService(2), createAndGo(4), createAndWait(5), destroy(6)  

sonetTCAStatus 1.3.6.1.4.1.5812.3.5.1.31
Represents the Threshold Crossing Alarm.
OBJECT-TYPE    
  INTEGER sonet-section-cv-tca-declared(1), sonet-section-ses-tca-declared(2), sonet-section-es-tca-declared(3), sonet-line-cv-tca-declared(4), sonet-line-ses-tca-declared(5), sonet-line-es-tca-declared(6), sonet-line-uas-tca-declared(7), sonet-line-farend-cv-tca-declared(8), sonet-line-farend-ses-tca-declared(9), sonet-line-farend-es-tca-declared(10), sonet-line-farend-uas-tca-declared(11), sonet-path-cv-tca-declared(12), sonet-path-ses-tca-declared(13), sonet-path-es-tca-declared(14), sonet-path-uas-tca-declared(15), sonet-path-farend-cv-tca-declared(16), sonet-path-farend-ses-tca-declared(17), sonet-path-farend-es-tca-declared(18), sonet-path-farend-uas-tca-declared(19), sonet-vt-cv-tca-declared(20), sonet-vt-ses-tca-declared(21), sonet-vt-es-tca-declared(22), sonet-vt-uas-tca-declared(23), sonet-vt-farend-cv-tca-declared(24), sonet-vt-farend-ses-tca-declared(25), sonet-vt-farend-es-tca-declared(26), sonet-vt-farend-uas-tca-declared(27)  

atmPortTable 1.3.6.1.4.1.5812.3.6
The ATM Port Table
OBJECT-TYPE    
  SEQUENCE OF  
    AtmPortEntry

atmPortEntry 1.3.6.1.4.1.5812.3.6.1
Entry containing information about atm ports
OBJECT-TYPE    
  AtmPortEntry  

atmPortVPTunnel 1.3.6.1.4.1.5812.3.6.1.1
Whether this port is a VP Tunnel
OBJECT-TYPE    
  TruthValue  

atmPortMaxTotalBits 1.3.6.1.4.1.5812.3.6.1.2
Max Total Bits of VPI & VCI
OBJECT-TYPE    
  INTEGER  

atmPortTiming 1.3.6.1.4.1.5812.3.6.1.3
Timing Mode
OBJECT-TYPE    
  INTEGER internal(1), loop(2)  

atmPortInCells 1.3.6.1.4.1.5812.3.6.1.4
Input Cell Count
OBJECT-TYPE    
  Counter32  

atmPortOutCells 1.3.6.1.4.1.5812.3.6.1.5
Output Cell Count
OBJECT-TYPE    
  Counter32  

atmPortCDVT 1.3.6.1.4.1.5812.3.6.1.6
Cell Delay Variation Tolerance (CDVT) is measured in units of seconds per cell. For OC12c ATM the link rate is approximately 1.4 million cells per second, each cell time being approximately 700 nanoseconds. Its value is initialized to 50,000 which is approximately 0.7% of the OC12c line rate. The value ranges from 5,000 to 100,000 which gives us a CDVT range of 7 to 141 cell times.
OBJECT-TYPE    
  INTEGER 5000..100000  

atmPortMaxActvBits 1.3.6.1.4.1.5812.3.6.1.7
Maximum active VPI/VCI bits
OBJECT-TYPE    
  OCTET STRING  

atmPortHCInCells 1.3.6.1.4.1.5812.3.6.1.8
64 bit input cell count
OBJECT-TYPE    
  Counter64  

atmPortHCOutCells 1.3.6.1.4.1.5812.3.6.1.9
64 bit output cell count
OBJECT-TYPE    
  Counter64  

atmPortRowStatus 1.3.6.1.4.1.5812.3.6.1.10
This variable is used to create or delete instances of atm ports This variable subsumes the admin state variable, and once the row is created, its value returns the admin state of the port
OBJECT-TYPE    
  INTEGER active(1), notInService(2), createAndGo(4), createAndWait(5), destroy(6)  

opticalPortTable 1.3.6.1.4.1.5812.3.7
The Optical Port Table
OBJECT-TYPE    
  SEQUENCE OF  
    OpticalPortEntry

opticalPortEntry 1.3.6.1.4.1.5812.3.7.1
This describes the attributes of optical ports in the system
OBJECT-TYPE    
  OpticalPortEntry  

lambda 1.3.6.1.4.1.5812.3.7.1.1
The purpose of this variable is to be used as the third component of the index into the optical port table
OBJECT-TYPE    
  INTEGER  

opticalPortMode 1.3.6.1.4.1.5812.3.7.1.2
The mode of operation of the port. This is set initially by the user and can only be changed by the user. It is not a status. By default, all optical ports in the system come up as working. They have to be explicitly configured to work in a protected mode or to be turned off.
OBJECT-TYPE    
  INTEGER disabled(1), working(2), protected(3)  

opticalPortRxSMselect 1.3.6.1.4.1.5812.3.7.1.3
This object selects which lambda to send over the back-plane to the different switch module.
OBJECT-TYPE    
  INTEGER primary(1), reserve(2), both(3), none(4)  

opticalPortTxSMselect 1.3.6.1.4.1.5812.3.7.1.4
Selects between lambda feeds on the back plane wich originate in different switch module.
OBJECT-TYPE    
  INTEGER primary(1), reserve(2)  

opticalPortRxSignalState 1.3.6.1.4.1.5812.3.7.1.5
Provides the status of the received optical signal - whether it is detected or not.
OBJECT-TYPE    
  INTEGER detected(1), lossOfSignal(2)  

opticalPortRxFrameState 1.3.6.1.4.1.5812.3.7.1.6
Frame state of signal as detected by SW at SONET framer. This state is auto set by software.
OBJECT-TYPE    
  INTEGER lossOfFrame(1), detected(2)  

opticalPortTxStatus 1.3.6.1.4.1.5812.3.7.1.7
Provides the status of the transmitter for the optical port. This provides the operational condition of the transmitter. The value of it could be 'Good' even though it is not transmitting any signal due to some reason.
OBJECT-TYPE    
  INTEGER good(1), bad(2)  

opticalPortTxEnable 1.3.6.1.4.1.5812.3.7.1.8
Whether the transmission of data and interrupts on the optical port is enabled or disabled
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

opticalPortLaserPowerLevel 1.3.6.1.4.1.5812.3.7.1.9
The laser power level on the port - this variable is useful for tunable lasers. Currently will return a value of high(1)
OBJECT-TYPE    
  INTEGER high(1), low(2)  

opticalPortLaserWavelength 1.3.6.1.4.1.5812.3.7.1.10
Laser wavelength on the optical port. Currently will return 1 for DWDM ports, 2 for 1310 ports, 3 for 1550 ports and 4 for ports that support both 1310 and 1550 nm wavelengths. This value however will be overshadowed by a 1310 or 1550 wavelength card present in that system. The list will be expanded later to give the exact 15xx wavelength. Useful for tunable lasers to control the 15xx wavelength
OBJECT-TYPE    
  INTEGER fifteenXX(1), thirteenTen(2), fifteenFifty(3), thirteenTenFifteenFifty(4)  

opticalPortRowStatus 1.3.6.1.4.1.5812.3.7.1.11
This variable is used to create or delete instances of optical port
OBJECT-TYPE    
  INTEGER createAndGo(4), destroy(6)  

ringPortTable 1.3.6.1.4.1.5812.3.8
A table containing ring port variables.
OBJECT-TYPE    
  SEQUENCE OF  
    RingPortEntry

ringPortEntry 1.3.6.1.4.1.5812.3.8.1
Entry in the table for a single ring port.
OBJECT-TYPE    
  RingPortEntry  

ringPortArbiterEnabled 1.3.6.1.4.1.5812.3.8.1.1
The arbiter enabled Boolean defines whether the ring port Arbitration Logic is enabled or not. The Arbitration Logic services requests for extra data columns from an elastic bandwidth pool.
OBJECT-TYPE    
  TruthValue  

ringPortFrameMode 1.3.6.1.4.1.5812.3.8.1.2
The frame mode defines the data path mode of the ring port. The choices include AXSON and POS. AXSON frame mode means the ring encapsulates data inside AXSON frames, and POS means data is encapsulated using the Packet over SONET standard HDLC mechanism.
OBJECT-TYPE    
  INTEGER axson(1), pos(2)  

ringPortMaxChannels 1.3.6.1.4.1.5812.3.8.1.3
The max channels parameter sizes the number of AxSON channels supported on the ring port. This determines number of ingress and egress queues and the amount of queue memory available.
OBJECT-TYPE    
  INTEGER 0..63  

ringPortMaxSubChannels 1.3.6.1.4.1.5812.3.8.1.4
The max sub-channels parameter sizes the number of AxSON sub-channels supported in a particular AxSON channel. This determines the amount of queue memory required.
OBJECT-TYPE    
  INTEGER 0..4095  

ringPortAutoQueueSizing 1.3.6.1.4.1.5812.3.8.1.5
Defines whether Axson channel queues may be automatically resized during provisioning.
OBJECT-TYPE    
  TruthValue  

ringPortRingMode 1.3.6.1.4.1.5812.3.8.1.6
Whether the ring port is connected to the working ring or the protected ring
OBJECT-TYPE    
  INTEGER working(1), protected(2)  

ringPortNodeId 1.3.6.1.4.1.5812.3.8.1.7
This defines the temporal discovery of the node in the logical ring
OBJECT-TYPE    
  INTEGER 0..31  

ringPortAdminStatus 1.3.6.1.4.1.5812.3.8.1.8
Gives the possible ringPort Administration Status .
OBJECT-TYPE    
  INTEGER up(1), down(2), redundant(3), diagnostic(4)  

ringPortOperStatus 1.3.6.1.4.1.5812.3.8.1.9
Gives the ringPortNodeId operational status of the AXSON interface .
OBJECT-TYPE    
  INTEGER up(1), down(2)  

ringPortRxFrames 1.3.6.1.4.1.5812.3.8.1.10
This object sepcifies the number of frames received at this interface.
OBJECT-TYPE    
  Counter  

ringPortRxFrameErrors 1.3.6.1.4.1.5812.3.8.1.11
Number of errored frames received at this interface.
OBJECT-TYPE    
  Counter  

ringPortTxFrames 1.3.6.1.4.1.5812.3.8.1.12
This object sepcifies the number of frames transmitted from this interface.
OBJECT-TYPE    
  Counter  

ringPortMaxTDMChannels 1.3.6.1.4.1.5812.3.8.1.13
The maximum number of TDM channels supported on the ring
OBJECT-TYPE    
  INTEGER 0..499  

ringPortK1K2Status 1.3.6.1.4.1.5812.3.8.1.14
The status indicated by the K1,K2 bytes in the SONET frame overhead
OBJECT-TYPE    
  INTEGER set(1), clear(2)  

ringPortAISStatus 1.3.6.1.4.1.5812.3.8.1.15
The status indicated by the AIS bytes in the SONET frame overhead
OBJECT-TYPE    
  INTEGER set(1), clear(2)  

ringPortPHYStatus 1.3.6.1.4.1.5812.3.8.1.16
The physical status of the ring port.
OBJECT-TYPE    
  INTEGER up(1), down(2), lower-layer-down(3), unknown(4)  

tdmIoDS3PortTable 1.3.6.1.4.1.5812.3.9
The DS3 TDM IO Port Table
OBJECT-TYPE    
  SEQUENCE OF  
    TdmIoDS3PortEntry

tdmIoDS3PortEntry 1.3.6.1.4.1.5812.3.9.1
Entry containing information about TDM IO DS3 ports
OBJECT-TYPE    
  TdmIoDS3PortEntry  

tdmIoDS3PortPBitESS15Min 1.3.6.1.4.1.5812.3.9.1.1
15 minute threshold for P-Bit Errored Seconds
OBJECT-TYPE    
  INTEGER 1..900  

tdmIoDS3PortPBitESS1Day 1.3.6.1.4.1.5812.3.9.1.2
1 day threshold for P-Bit Errored Seconds
OBJECT-TYPE    
  INTEGER 1..65535  

tdmIoDS3PortPBitSESS15Min 1.3.6.1.4.1.5812.3.9.1.3
15 minute threshold for P-Bit Severely Errored Seconds
OBJECT-TYPE    
  INTEGER 1..900  

tdmIoDS3PortPBitSESS1Day 1.3.6.1.4.1.5812.3.9.1.4
1 day threshold for P-Bit Severely Errored Seconds
OBJECT-TYPE    
  INTEGER 1..65535  

tdmIoDS3PortSEFSS15Min 1.3.6.1.4.1.5812.3.9.1.5
15 minute threshold for Severely Errored Framing Seconds
OBJECT-TYPE    
  INTEGER 1..900  

tdmIoDS3PortSEFSS1Day 1.3.6.1.4.1.5812.3.9.1.6
1 day threshold for Severely Errored Framing Seconds
OBJECT-TYPE    
  INTEGER 1..65535  

tdmIoDS3PortUASS15Min 1.3.6.1.4.1.5812.3.9.1.7
15 minute threshold for Severely Errored Framing Seconds
OBJECT-TYPE    
  INTEGER 1..900  

tdmIoDS3PortUASS1Day 1.3.6.1.4.1.5812.3.9.1.8
1 day threshold for Unavailable Seconds
OBJECT-TYPE    
  INTEGER 1..65535  

tdmIoDS3PortLineCVS15Min 1.3.6.1.4.1.5812.3.9.1.9
15 minute threshold for Line-Coding Violations
OBJECT-TYPE    
  INTEGER 1..16383  

tdmIoDS3PortLineCVS1Day 1.3.6.1.4.1.5812.3.9.1.10
1 day threshold for Line-Coding Violations
OBJECT-TYPE    
  INTEGER 1..1048575  

tdmIoDS3PortPBitCVS15Min 1.3.6.1.4.1.5812.3.9.1.11
15 minute threshold for P-Bit Coding Violations
OBJECT-TYPE    
  INTEGER 1..16383  

tdmIoDS3PortPBitCVS1Day 1.3.6.1.4.1.5812.3.9.1.12
1 day threshold for P-Bit Coding Violations
OBJECT-TYPE    
  INTEGER 1..1048575  

tdmIoDS3PortLineESS15Min 1.3.6.1.4.1.5812.3.9.1.13
15 minute threshold for Line Errored Seconds
OBJECT-TYPE    
  INTEGER 1..900  

tdmIoDS3PortLineESS1Day 1.3.6.1.4.1.5812.3.9.1.14
1 day threshold for Line Errored Seconds
OBJECT-TYPE    
  INTEGER 1..65535  

tdmIoDS3PortCBitCVS15Min 1.3.6.1.4.1.5812.3.9.1.15
15 minute threshold for C-Bit Coding Violations
OBJECT-TYPE    
  INTEGER 1..16383  

tdmIoDS3PortCBitCVS1Day 1.3.6.1.4.1.5812.3.9.1.16
1 day threshold for C-Bit Coding Violations
OBJECT-TYPE    
  INTEGER 1..1048575  

tdmIoDS3PortCBitESS15Min 1.3.6.1.4.1.5812.3.9.1.17
15 minute threshold for C-Bit Errored Seconds
OBJECT-TYPE    
  INTEGER 1..900  

tdmIoDS3PortCBitESS1Day 1.3.6.1.4.1.5812.3.9.1.18
1 day threshold for C-Bit Errored Seconds
OBJECT-TYPE    
  INTEGER 1..65535  

tdmIoDS3PortCBitSESS15Min 1.3.6.1.4.1.5812.3.9.1.19
15 minute threshold for C-Bit Severely Errored Seconds
OBJECT-TYPE    
  INTEGER 1..900  

tdmIoDS3PortCBitSESS1Day 1.3.6.1.4.1.5812.3.9.1.20
1 day threshold for C-Bit Severely Errored Seconds
OBJECT-TYPE    
  INTEGER 1..65535  

tdmIoDS3PortRowStatus 1.3.6.1.4.1.5812.3.9.1.21
This variable is used to create or delete instances of TDM IO DS3 ports. This variable subsumes the admin state variable, and once the row is created, its value returns the admin state of the port
OBJECT-TYPE    
  INTEGER active(1), notInService(2), createAndGo(4), createAndWait(5), destroy(6)  

posPortTable 1.3.6.1.4.1.5812.3.10
The POS Port Table
OBJECT-TYPE    
  SEQUENCE OF  
    PosPortEntry

posPortEntry 1.3.6.1.4.1.5812.3.10.1
Entry containing information about POS ports
OBJECT-TYPE    
  PosPortEntry  

posPortTransportSegmentCount 1.3.6.1.4.1.5812.3.10.1.1
Number of provisioned connections on port.
OBJECT-TYPE    
  Counter32  

posPortMode 1.3.6.1.4.1.5812.3.10.1.2
mode of operation.
OBJECT-TYPE    
  INTEGER transparent(1), bridgedDataMode(2), vlan(3), macAddr(4), ipAddr(5), mpls(6), mapOS(7)  

posPortDefaultVID 1.3.6.1.4.1.5812.3.10.1.3
Port's default VLAN ID.
OBJECT-TYPE    
  Unsigned32  

posPortMinPktSize 1.3.6.1.4.1.5812.3.10.1.4
It is defined as the minimum number of bytes encapsulated in the POS frame including the FCS, but excluding byte stuffing.
OBJECT-TYPE    
  INTEGER 4..4096  

posPortMaxPktSize 1.3.6.1.4.1.5812.3.10.1.5
It is defined as the maximum number of bytes encapsulated in the POS frame including the FCS, but excluding byte stuffing.
OBJECT-TYPE    
  INTEGER 4..4096  

posPortMinPktViolations 1.3.6.1.4.1.5812.3.10.1.6
This object gives the number of times the system had detected a packet of size less than the acceptable minimum.
OBJECT-TYPE    
  Counter32  

posPortMaxPktViolations 1.3.6.1.4.1.5812.3.10.1.7
This object gives the number of times the system had detected a packet of size greater than the acceptable minimum.
OBJECT-TYPE    
  Counter32  

portSpeedStatusTrap 1.3.6.1.4.1.5812.20
Change in speed of an interface e.g. 10 or 100 for a Fast Ethernet port
TRAP-TYPE    
  ifSpeed  

etherPortDuplexStatusTrap 1.3.6.1.4.1.5812.21
Change in the duplex status of an ethernet port , 2 means half-duplex, 3 means full duplex
TRAP-TYPE    
  dot3StatsDuplexStatus  

etherPortAutonegStatusTrap 1.3.6.1.4.1.5812.22
Change in status of the autoneg process, 3 means it has completed
TRAP-TYPE    
  ifMauAutoNegConfig  

sonetSectionLOSChange 1.3.6.1.4.1.5812.27
Change in the SONET LOS status.
TRAP-TYPE    
  sonetSectionCurrentStatus  

sonetSectionLOFChange 1.3.6.1.4.1.5812.28
Change in the SONET LOF status.
TRAP-TYPE    
  sonetSectionCurrentStatus  

sonetLineAISChange 1.3.6.1.4.1.5812.29
Change in the SONET Line AIS status.
TRAP-TYPE    
  sonetLineCurrentStatus  

sonetLineRDIChange 1.3.6.1.4.1.5812.30
Change in the SONET Line RDI status.
TRAP-TYPE    
  sonetLineCurrentStatus  

sonetPathLOPChange 1.3.6.1.4.1.5812.31
Change in the SONET Path LOP status.
TRAP-TYPE    
  sonetPathCurrentStatus  

sonetPathAISChange 1.3.6.1.4.1.5812.32
Change in the SONET Path AIS status.
TRAP-TYPE    
  sonetPathCurrentStatus  

sonetPathRDIChange 1.3.6.1.4.1.5812.33
Change in the SONET Path RDI status.
TRAP-TYPE    
  sonetPathCurrentStatus  

sonetPathUNEQPChange 1.3.6.1.4.1.5812.34
Indicates whether the SONET path is equipped or not.
TRAP-TYPE    
  sonetPathCurrentStatus  

sonetPathPSLMChange 1.3.6.1.4.1.5812.35
Indicates if there is any mismatch in the SONET signal label.
TRAP-TYPE    
  sonetPathCurrentStatus  

sonetVTLOPChange 1.3.6.1.4.1.5812.36
Change in the SONET VT LOP status.
TRAP-TYPE    
  sonetVTCurrentStatus  

sonetVTAISChange 1.3.6.1.4.1.5812.37
Change in the SONET VT AIS status.
TRAP-TYPE    
  sonetVTCurrentStatus  

sonetVTRDIChange 1.3.6.1.4.1.5812.38
Change in the SONET VT RDI status.
TRAP-TYPE    
  sonetVTCurrentStatus  

sonetVTRFIChange 1.3.6.1.4.1.5812.39
Change in the SONET VT RFI status.
TRAP-TYPE    
  sonetVTCurrentStatus  

sonetVTUNEQPChange 1.3.6.1.4.1.5812.40
Indicates whether the SONET VT is equipped or not.
TRAP-TYPE    
  sonetVTCurrentStatus  

sonetVTPSLMChange 1.3.6.1.4.1.5812.41
Indicates if there is any mismatch in the SONET signal label.
TRAP-TYPE    
  sonetVTCurrentStatus  

ringPortK1K2Change 1.3.6.1.4.1.5812.47
Indicates the change in status indicated by K1,K2 bytes
TRAP-TYPE    
  ringPortK1K2Status  

ringPortAISChange 1.3.6.1.4.1.5812.48
A signal indicating a change of status indicated by the AIS bytes
TRAP-TYPE    
  ringPortAISStatus  

ringPortPHYChange 1.3.6.1.4.1.5812.49
A trap indicating the change in phy status of ring port
TRAP-TYPE    
  ringPortPHYStatus  

sonetPortTCAlarm 1.3.6.1.4.1.5812.50
A SONET alarm threshold has been crossed.
TRAP-TYPE    
  sonetTCAStatus  

dsxAlarm 1.3.6.1.4.1.5812.55
The status of a DSx line has changed.
TRAP-TYPE    
  dsxStatus  

Defined Objects

PortEntry  
SEQUENCE    
  INTEGER as portNo  
  InterfaceIndex as mib2IfIndex  

EtherPortEntry  
SEQUENCE    
  INTEGER as etherPortSpeedCfg  
  INTEGER as etherPortSpeedStatus  
  INTEGER as etherPortDuplexCfg  
  INTEGER as etherPortLoopback  
  INTEGER as etherPortPhyReset  
  Counter as etherPortStatsTxPkts64Octets  
  Counter as etherPortStatsTxPkts65to127Octets  
  Counter as etherPortStatsTxPkts128to255Octets  
  Counter as etherPortStatsTxPkts256to511Octets  
  Counter as etherPortStatsTxPkts512to1023Octets  
  Counter as etherPortStatsTxPkts1024to1518Octets  
  Counter as etherPortStatsTxPkts1519to1530Octets  
  Counter as etherPortStatsTxFCSErrors  
  Counter as etherPortStatsTxOversize  
  Counter as etherPortStatsTxUndersize  
  Counter as etherPortStatsTxControlFrames  
  Counter as etherPortStatsTxBadFifoUnderrun  
  Counter as etherPortStatsTxBadFifoOverrun  
  Counter as etherPortStatsTxDropFifoOverrun  
  Counter as etherPortStatsTxBadParityError  
  Counter as etherPortStatsTxDropParityError  
  Counter as etherPortStatsTxBadSequenceError  
  Counter as etherPortStatsTxDropSequenceError  
  Counter as etherPortStatsTxBadJamError  
  Counter as etherPortStatsTxDropJamError  
  INTEGER as etherPortSpeedTrapEnable  
  INTEGER as etherPortDuplexTrapEnable  
  INTEGER as etherPortAutonegTrapEnable  
  INTEGER as etherPortRowStatus  
  INTEGER as etherPortAutonegAdvSpeed  
  INTEGER as etherPortAutonegAdvDuplex  
  INTEGER as etherPortPauseStateReceived  
  INTEGER as etherPortVlanMode  
  INTEGER as etherPortDefaultVlanId  
  Counter as etherPortRxOverrun  
  Counter as etherPortRxSyncErrors  
  Counter as etherPortRxDelSeqErrors  
  Counter as etherPortRxFifoOverrunErrors  
  Counter as etherPortRxControlFrames  
  Counter as etherPortRxThreshOvrszFrames  
  Counter as etherPortStatsRxPkts1519to1530Octets  

TdmIoDS1PortEntry  
SEQUENCE    
  INTEGER as tdmIoDS1PortType  
  INTEGER as tdmIoDS1PortTiming  
  INTEGER as tdmIoDS1PortBuildOut  
  INTEGER as tdmIoDS1PortFraming  
  INTEGER as tdmIoDS1PortCoding  
  INTEGER as tdmIoDS1PortLoopbackState  
  INTEGER as tdmIoDS1PortLoopbackType  
  INTEGER as tdmIoDS1PortLoopbackResults  
  INTEGER as tdmIoDS1PortLoopbackLLbActCode  
  INTEGER as tdmIoDS1PortLoopbackLLbDeactCode  
  INTEGER as tdmIoDS1PortLoopbackLlbActCodeLen  
  INTEGER as tdmIoDS1PortLoopbackLlbDeactCodeLen  
  INTEGER as tdmIoDS1PortLoopbackLlbControl  
  INTEGER as tdmIoDS1PortLoopbackLlbGenPath  
  INTEGER as tdmIoDS1PortLoopbackLlbMonPath  
  INTEGER as tdmIoDS1PortPrbsAlgorithm  
  INTEGER as tdmIoDS1PortPrbsInversion  
  INTEGER as tdmIoDS1PortPrbsGenPath  
  INTEGER as tdmIoDS1PortPrbsMonPath  
  INTEGER as tdmIoDS1PortPrbsMonitor  
  INTEGER as tdmIoDS1PortPrbsTransmit  
  Counter as tdmIoDS1PortPrbsBec  
  INTEGER as tdmIoDS1PortBertState  
  INTEGER as tdmIoDS1PortBertPattern  
  INTEGER as tdmIoDS1PortBertDuration  
  INTEGER as tdmIoDS1PortBertResults  
  INTEGER as tdmIoDS1PortLineESS15Min  
  INTEGER as tdmIoDS1PortPathESS15Min  
  INTEGER as tdmIoDS1PortLineESS1Day  
  INTEGER as tdmIoDS1PortPathESS1Day  
  INTEGER as tdmIoDS1PortPathCVS15Min  
  INTEGER as tdmIoDS1PortPathCVS1Day  
  INTEGER as tdmIoDS1PortPathSESS15Min  
  INTEGER as tdmIoDS1PortPathSESS1Day  
  INTEGER as tdmIoDS1PortPathSASS15Min  
  INTEGER as tdmIoDS1PortPathSASS1Day  
  INTEGER as tdmIoDS1PortPathCSS15Min  
  INTEGER as tdmIoDS1PortPathCSS1Day  
  INTEGER as tdmIoDS1PortPathUASS15Min  
  INTEGER as tdmIoDS1PortRowStatus  
  INTEGER as dsxStatus  
  INTEGER as tdmIoDS1PortLCVCount  

SonetPortEntry  
SEQUENCE    
  INTEGER as sonetPortType  
  OCTET STRING as sonetPortIdString  
  INTEGER as sonetPortTiming  
  INTEGER as sonetPortLoopback  
  INTEGER as sonetPortScrambling  
  INTEGER as sonetPortChannelization  
  Unsigned32 as sonetPortConfigedChans  
  INTEGER as sonetPortSectESS15Min  
  INTEGER as sonetPortLineESS15Min  
  INTEGER as sonetPortPathESS15Min  
  INTEGER as sonetPortSectESS1Day  
  INTEGER as sonetPortLineESS1Day  
  INTEGER as sonetPortPathESS1Day  
  INTEGER as sonetPortSectCVS15Min  
  INTEGER as sonetPortLineCVS15Min  
  INTEGER as sonetPortPathCVS15Min  
  INTEGER as sonetPortSectCVS1Day  
  INTEGER as sonetPortLineCVS1Day  
  INTEGER as sonetPortPathCVS1Day  
  INTEGER as sonetPortSectSESS15Min  
  INTEGER as sonetPortLineSESS15Min  
  INTEGER as sonetPortPathSESS15Min  
  INTEGER as sonetPortSectSESS1Day  
  INTEGER as sonetPortLineSESS1Day  
  INTEGER as sonetPortPathSESS1Day  
  INTEGER as sonetPortLineUASS15Min  
  INTEGER as sonetPortPathUASS15Min  
  INTEGER as sonetPortLineUASS1Day  
  INTEGER as sonetPortPathUASS1Day  
  INTEGER as sonetPortRowStatus  
  INTEGER as sonetTCAStatus  

AtmPortEntry  
SEQUENCE    
  TruthValue as atmPortVPTunnel  
  INTEGER as atmPortMaxTotalBits  
  INTEGER as atmPortTiming  
  Counter32 as atmPortInCells  
  Counter32 as atmPortOutCells  
  INTEGER as atmPortCDVT  
  OCTET STRING as atmPortMaxActvBits  
  Counter64 as atmPortHCInCells  
  Counter64 as atmPortHCOutCells  
  INTEGER as atmPortRowStatus  

OpticalPortEntry  
SEQUENCE    
  INTEGER as lambda  
  INTEGER as opticalPortMode  
  INTEGER as opticalPortRxSMselect  
  INTEGER as opticalPortTxSMselect  
  INTEGER as opticalPortRxSignalState  
  INTEGER as opticalPortRxFrameState  
  INTEGER as opticalPortTxStatus  
  INTEGER as opticalPortTxEnable  
  INTEGER as opticalPortLaserPowerLevel  
  INTEGER as opticalPortLaserWavelength  
  INTEGER as opticalPortRowStatus  

RingPortEntry  
SEQUENCE    
  TruthValue as ringPortArbiterEnabled  
  INTEGER as ringPortFrameMode  
  INTEGER as ringPortMaxChannels  
  INTEGER as ringPortMaxSubChannels  
  TruthValue as ringPortAutoQueueSizing  
  INTEGER as ringPortRingMode  
  INTEGER as ringPortNodeId  
  INTEGER as ringPortAdminStatus  
  INTEGER as ringPortOperStatus  
  Counter as ringPortRxFrames  
  Counter as ringPortRxFrameErrors  
  Counter as ringPortTxFrames  
  INTEGER as ringPortMaxTDMChannels  
  INTEGER as ringPortK1K2Status  
  INTEGER as ringPortAISStatus  
  INTEGER as ringPortPHYStatus  

TdmIoDS3PortEntry  
SEQUENCE    
  INTEGER as tdmIoDS3PortPBitESS15Min  
  INTEGER as tdmIoDS3PortPBitESS1Day  
  INTEGER as tdmIoDS3PortPBitSESS15Min  
  INTEGER as tdmIoDS3PortPBitSESS1Day  
  INTEGER as tdmIoDS3PortSEFSS15Min  
  INTEGER as tdmIoDS3PortSEFSS1Day  
  INTEGER as tdmIoDS3PortUASS15Min  
  INTEGER as tdmIoDS3PortUASS1Day  
  INTEGER as tdmIoDS3PortLineCVS15Min  
  INTEGER as tdmIoDS3PortLineCVS1Day  
  INTEGER as tdmIoDS3PortPBitCVS15Min  
  INTEGER as tdmIoDS3PortPBitCVS1Day  
  INTEGER as tdmIoDS3PortLineESS15Min  
  INTEGER as tdmIoDS3PortLineESS1Day  
  INTEGER as tdmIoDS3PortCBitCVS15Min  
  INTEGER as tdmIoDS3PortCBitCVS1Day  
  INTEGER as tdmIoDS3PortCBitESS15Min  
  INTEGER as tdmIoDS3PortCBitESS1Day  
  INTEGER as tdmIoDS3PortCBitSESS15Min  
  INTEGER as tdmIoDS3PortCBitSESS1Day  
  INTEGER as tdmIoDS3PortRowStatus  

PosPortEntry  
SEQUENCE    
  Counter32 as posPortTransportSegmentCount  
  INTEGER as posPortMode  
  Unsigned32 as posPortDefaultVID  
  INTEGER as posPortMinPktSize  
  INTEGER as posPortMaxPktSize  
  Counter32 as posPortMinPktViolations  
  Counter32 as posPortMaxPktViolations