QB-DWS-MIB

File: QB-DWS-MIB.mib (60348 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB QUANTUMBRIDGE-REG QBSYS-SYSTEM-MIB
ATM-TC-MIB

Imported symbols

NOTIFICATION-TYPE MODULE-IDENTITY OBJECT-TYPE
Gauge32 Counter32 Unsigned32
Integer32 TimeTicks IpAddress
TEXTUAL-CONVENTION TruthValue TimeStamp
RowStatus DisplayString MODULE-COMPLIANCE
OBJECT-GROUP InterfaceIndex InterfaceIndexOrZero
ifIndex qbMibs qbSysModuleSlot
qbSysIotSerialNumber AtmAddr AtmConnKind
AtmConnCastType AtmServiceCategory AtmTrafficDescrParamIndex
AtmVpIdentifier AtmVcIdentifier AtmVorXAdminStatus
AtmVorXLastChange AtmVorXOperStatus atmNoClpNoScr

Defined Objects

qbDwsMIB 1.3.6.1.4.1.4323.2.3
This module defines additional objects for the provisioning and management of DWS links in Quantum bridge devices.
MODULE-IDENTITY    

qbDwsObjects 1.3.6.1.4.1.4323.2.3.1
OBJECT IDENTIFIER    

qbDwsNetGroup 1.3.6.1.4.1.4323.2.3.1.1
OBJECT IDENTIFIER    

qbDwsSysRangeMode 1.3.6.1.4.1.4323.2.3.1.1.1
The object that indicates a system wide range mode. When read, this object always returns the value 'ready(1)'. Setting this object to rangeAll(2) causes ranging of all IOTs that connect to this OAS.
OBJECT-TYPE    
  INTEGER ready(1), rangeAll(2)  

qbSysIotRecoverMode 1.3.6.1.4.1.4323.2.3.1.1.2
The object allows to set the IOT auto-recovery feature on the IOAS. Auto-recovery is global in scope, so when it is enabled, auto-recovery is attempted for all IOTs that are attached to the IOAS.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

qbDwsNetTable 1.3.6.1.4.1.4323.2.3.1.1.3
The Quantum Bridge PON Interface Table contains extensions of the standard MIB Interface Table, one entry per IOAS DWS interface. The table contains read-only objects and shows MIB objects for every Network interface
OBJECT-TYPE    
  SEQUENCE OF  
    QbDwsNetEntry

qbDwsNetEntry 1.3.6.1.4.1.4323.2.3.1.1.3.1
An entry in the Quantum Bridge DWS Interface Table that contains the Network interface's specific objects.
OBJECT-TYPE    
  QbDwsNetEntry  

qbDwsNetIfIndex 1.3.6.1.4.1.4323.2.3.1.1.3.1.1
The value of this object is the same as the corresponding ifIndex of the Network Interface in the ifTable.
OBJECT-TYPE    
  InterfaceIndex  

qbDwsNetBw 1.3.6.1.4.1.4323.2.3.1.1.3.1.2
The object indicates the total bandwidth rate that is available for reservation on this interface. This object is specified in Bits per second.
OBJECT-TYPE    
  QbBitRate  

qbDwsNetAllocatedBw 1.3.6.1.4.1.4323.2.3.1.1.3.1.3
The object indicates the total bandwidth rate that is currently subscribed. The subscribed bandwidth rate consists of the bandwidth rate allocated for all provisoned connections. This object is specified in Bits per sec(Bps).
OBJECT-TYPE    
  QbBitRate  

qbDwsNetAvailableBw 1.3.6.1.4.1.4323.2.3.1.1.3.1.4
The portion of this interface's capacity in bits per sec that is available for data traffic. This variable is adjusted for the allocated bandwidth. The formula for calculating this value is qbDwsNetBw - qbDwsNetAllocatedBw This object is specified in Bps.
OBJECT-TYPE    
  QbBitRate  

qbDwsNetAllocatedUbrBw 1.3.6.1.4.1.4323.2.3.1.1.3.1.5
The object indicates the total number of bandwidth that are currently allocated for packet/ubr traffic. This object is specified in Bps.
OBJECT-TYPE    
  QbBitRate  

qbDwsNetAllocatedCbrBw 1.3.6.1.4.1.4323.2.3.1.1.3.1.6
The object indicates the total number of bandwidth that is currently allocated for CBR traffic. This object is specified in Bps.
OBJECT-TYPE    
  QbBitRate  

qbDwsNetNumCbrConn 1.3.6.1.4.1.4323.2.3.1.1.3.1.7
The object indicates the total number of inactive and in-service CBR connections that are currently provisioned on this interface.
OBJECT-TYPE    
  Integer32  

qbDwsNetNumUbrConn 1.3.6.1.4.1.4323.2.3.1.1.3.1.8
The object indicates the total number of inactive and in-serice UBR connections that are currently provisioned on this interface.
OBJECT-TYPE    
  Integer32  

qbDwsNetNumIot 1.3.6.1.4.1.4323.2.3.1.1.3.1.9
The number of IOTs that are provisioned on the Network interface.
OBJECT-TYPE    
  Integer32  

qbDwsNetTxStatus 1.3.6.1.4.1.4323.2.3.1.1.3.1.10
This objects indicates the status of the DWS transmitter. The trap is generated by the SNMP agent when the IOAS DWS transmitter problem is detected. The trap contains the DWS module interface index.
OBJECT-TYPE    
  QbDwsIfStatus  

qbDwsNetTxStatusLastChange 1.3.6.1.4.1.4323.2.3.1.1.3.1.11
The value of MIB II's sysUpTime object at the time this DWS Interface entered its current status state.
OBJECT-TYPE    
  TimeStamp  

qbDwsNetLosIotAddr 1.3.6.1.4.1.4323.2.3.1.1.3.1.12
The object contains the address of the IOT for which a Los condition is detected. This indicates that no signal was detected within the expected time slot window. Note: The Los indication at the IOAS DWS card is a signal that an IOT is non-functioning.
OBJECT-TYPE    
  Integer32  

qbDwsNetLosIotTime 1.3.6.1.4.1.4323.2.3.1.1.3.1.13
The value of MIB II's sysUpTime object at the time when the qbDwsNetIotLos condition was detected.
OBJECT-TYPE    
  TimeStamp  

qbDwsNetEncryptStatus 1.3.6.1.4.1.4323.2.3.1.1.3.1.14
The object that enables and disables encryption on this interface.
OBJECT-TYPE    
  TruthValue  

qbDwsNetRangeMode 1.3.6.1.4.1.4323.2.3.1.1.3.1.15
The object that indicates a range mode. When read, this object always returns the value 'ready(1)'. Setting this object to rangeAll(2) causes ranging of all IOTs connected to this interface.
OBJECT-TYPE    
  INTEGER ready(1), rangeAll(2)  

qbDwsNetRxTsCount 1.3.6.1.4.1.4323.2.3.1.1.3.1.16
The total number of successfully received time slots.
OBJECT-TYPE    
  Counter32  

qbDwsNetTxTsCount 1.3.6.1.4.1.4323.2.3.1.1.3.1.17
The total number of successfully transmitted time slots.
OBJECT-TYPE    
  Counter32  

qbDwsNetRxMissingTs 1.3.6.1.4.1.4323.2.3.1.1.3.1.18
The number received time slots that have been missed.
OBJECT-TYPE    
  Counter32  

qbDwsNetRxIllegalTs 1.3.6.1.4.1.4323.2.3.1.1.3.1.19
The number illegal received time slots that have been detected.
OBJECT-TYPE    
  Counter32  

qbDwsNetTxJabberTs 1.3.6.1.4.1.4323.2.3.1.1.3.1.20
The number jabber transmitted time slots that have been detected.
OBJECT-TYPE    
  Counter32  

qbDwsNetTxOutOfFrameTs 1.3.6.1.4.1.4323.2.3.1.1.3.1.21
The number out of frame transmitted timeslots that have been detected.
OBJECT-TYPE    
  Counter32  

qbDwsNetTxHdrCrcTsErrs 1.3.6.1.4.1.4323.2.3.1.1.3.1.22
The number transmitted timeslots with the header protection error that have been detected.
OBJECT-TYPE    
  Counter32  

qbDwsNetOamRequests 1.3.6.1.4.1.4323.2.3.1.1.3.1.23
The number of OAM requests. These OAM requests are originated by the IOAS and sent to downstream IOTs.
OBJECT-TYPE    
  Counter32  

qbDwsNetOamResponses 1.3.6.1.4.1.4323.2.3.1.1.3.1.24
The number of OAM responses. These responses are generated by IOTs in response to downstream requests.
OBJECT-TYPE    
  Counter32  

qbDwsNetOamEvents 1.3.6.1.4.1.4323.2.3.1.1.3.1.25
The number of OAM events. These events are originated by IOT devices to signal abnormal conditions.
OBJECT-TYPE    
  Counter32  

qbDwsNetOamBadMsgs 1.3.6.1.4.1.4323.2.3.1.1.3.1.26
The total number of bad OAM messages.
OBJECT-TYPE    
  Counter32  

qbDwsNetLoopBack 1.3.6.1.4.1.4323.2.3.1.1.3.1.27
The Loopback status of this DWS port. Writing configures the port to go into the loopback mode. When placed in loopback mode the DWS port does a 'payload' loopback.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

qbDwsIotIfGroup 1.3.6.1.4.1.4323.2.3.1.2
OBJECT IDENTIFIER    

qbDwsIotIfConfTable 1.3.6.1.4.1.4323.2.3.1.2.1
The Quantum DWS interface table. One entry per each IOT's DWS interface.
OBJECT-TYPE    
  SEQUENCE OF  
    QbDwsIotIfConfEntry

qbDwsIotIfConfEntry 1.3.6.1.4.1.4323.2.3.1.2.1.1
An entry in the Quantum Bridge DWS Interface Table. The ifIndex is a DWS interface index from ifTable.
OBJECT-TYPE    
  QbDwsIotIfConfEntry  

qbDwsIotIfIndex 1.3.6.1.4.1.4323.2.3.1.2.1.1.1
The ifIndex of this interface in the ifTable.
OBJECT-TYPE    
  InterfaceIndex  

qbDwsIotNetIfIndex 1.3.6.1.4.1.4323.2.3.1.2.1.1.2
The ifIndex of this PON interface in the ifTable.
OBJECT-TYPE    
  InterfaceIndex  

qbDwsIotIfAddr 1.3.6.1.4.1.4323.2.3.1.2.1.1.3
The IOT terminal address.
OBJECT-TYPE    
  Integer32  

qbDwsIotIfConfPowerLevel 1.3.6.1.4.1.4323.2.3.1.2.1.1.4
The DWS interface's power level.
OBJECT-TYPE    
  Integer32  

qbDwsIotIfConfEqDelay 1.3.6.1.4.1.4323.2.3.1.2.1.1.5
The equal Delay time (in hundredths of a second).
OBJECT-TYPE    
  TimeTicks  

qbDwsIotIfConfWaveLength 1.3.6.1.4.1.4323.2.3.1.2.1.1.6
The wave length value for this DWS interface.
OBJECT-TYPE    
  Integer32  

qbDwsIotIfUbrBw 1.3.6.1.4.1.4323.2.3.1.2.1.1.7
The object indicates the total UBR bandwidth rate that is reserved for a given IOT interface. This object is specified in Bits per second.
OBJECT-TYPE    
  QbBitRate  

qbDwsIotIfCbrBw 1.3.6.1.4.1.4323.2.3.1.2.1.1.8
The object indicates the total CBR bandwidth rate that is reserved for a given IOT interface. This object is specified in Bits per second.
OBJECT-TYPE    
  QbBitRate  

qbDwsIotIfTxStatus 1.3.6.1.4.1.4323.2.3.1.2.1.1.9
This objects indicates the status of the IOT DWS Port. The txFailure(2) state indicates that the laser transmitter failed. The rxFailure(3) state indicates that no signal was detected within the expected timeslot window. It signals that there is a problem with the DWS port receiver. When this object is changed, the ifOperStatus and ifLastChnaged of this interface must also be changed. Note: The trap is generated by the SNMP agent when the IOT DWS status is changed. The trap contains the IOAS DWS card interface index and IOT address.
OBJECT-TYPE    
  QbDwsIfStatus  

qbDwsIotIfTxStatusLastChange 1.3.6.1.4.1.4323.2.3.1.2.1.1.10
The value of MIB II's sysUpTime object at the time this DWS Interface enters its current status state.
OBJECT-TYPE    
  TimeStamp  

qbDwsIotIfLastRangeTime 1.3.6.1.4.1.4323.2.3.1.2.1.1.11
The value of MIB II's sysUpTime object at the last time when this IOT is ranged
OBJECT-TYPE    
  TimeStamp  

qbDwsIotIfStatsTable 1.3.6.1.4.1.4323.2.3.1.2.2
The Quantum Bridge IOT's terminal table. One entry per each RT.
OBJECT-TYPE    
  SEQUENCE OF  
    QbDwsIotIfStatsEntry

qbDwsIotIfStatsEntry 1.3.6.1.4.1.4323.2.3.1.2.2.1
An entry in the Quantum DWS Interface Statistics Table.
OBJECT-TYPE    
  QbDwsIotIfStatsEntry  

qbDwsIotIfStatsUtil 1.3.6.1.4.1.4323.2.3.1.2.2.1.1
The object indicates the utilization of the Network Interface transmission rate capacity by the IOT DWS interface. This object is specified in percents.
OBJECT-TYPE    
  INTEGER 0..100  

qbDwsIotIfStatsOamRequests 1.3.6.1.4.1.4323.2.3.1.2.2.1.2
The number of received downstream OAM request messages.
OBJECT-TYPE    
  Counter32  

qbDwsIotIfStatsOamResponses 1.3.6.1.4.1.4323.2.3.1.2.2.1.3
The number of transmitted upstream OAM response messages.
OBJECT-TYPE    
  Counter32  

qbDwsIotIfStatsOamEvents 1.3.6.1.4.1.4323.2.3.1.2.2.1.4
The number of OAM event messages originated by the interface.
OBJECT-TYPE    
  Counter32  

qbDwsIotIfStatsOamBadMsgs 1.3.6.1.4.1.4323.2.3.1.2.2.1.5
The number of wrong OAM messages received on this interface.
OBJECT-TYPE    
  Counter32  

qbDwsIotIfStatsCrcErrs 1.3.6.1.4.1.4323.2.3.1.2.2.1.6
The summary number of the IOT DWS CRC subframe and time slot header CRC errors.
OBJECT-TYPE    
  Counter32  

qbDwsIotIfStatsTsHdrParityErrs 1.3.6.1.4.1.4323.2.3.1.2.2.1.7
The number of Time Slot header parity errors that have been detected on the interface.
OBJECT-TYPE    
  Counter32  

qbDwsIotIfStatsFrameLossErrs 1.3.6.1.4.1.4323.2.3.1.2.2.1.8
The number of Loss frame errors that have been detected on the interface.
OBJECT-TYPE    
  Counter32  

qbDwsIotIfStatsSignalLossErrs 1.3.6.1.4.1.4323.2.3.1.2.2.1.9
The number of Loss signal errors that have been detected on the interface.
OBJECT-TYPE    
  Counter32  

qbDwsIotIfStatsRxAal1Cells 1.3.6.1.4.1.4323.2.3.1.2.2.1.10
The number of received AAL1 ATM cells.
OBJECT-TYPE    
  Counter32  

qbDwsIotIfStatsTxAal1Cells 1.3.6.1.4.1.4323.2.3.1.2.2.1.11
The number of transmitted ATM cells .
OBJECT-TYPE    
  Counter32  

qbIotPktIfGroup 1.3.6.1.4.1.4323.2.3.1.3
OBJECT IDENTIFIER    

qbIotPktIfConfTable 1.3.6.1.4.1.4323.2.3.1.3.1
The Quantum Bridge PKT configuration table contains cross-connections between Ethernet interfaces and corresponding PVC/AAL5 that are configured at a WAN port. An entry in the table may be created, destroyed or modified. This table lists all PVCs within the System that send/receive packet traffic to/from the ATM cloud.
OBJECT-TYPE    
  SEQUENCE OF  
    QbIotPktIfConfEntry

qbIotPktIfConfEntry 1.3.6.1.4.1.4323.2.3.1.3.1.1
An entry in the Quantum Bridge IP configuration table. For every IP traffic flow, there is a corresponding row in this table which contains a DWS interface index, and a VPI/VCI pair of PVC configured at a SONET port for a given DWS interface. The creation of a row in this table causes a corresponding entry in the atmVclTable of the ATM-MIB to be automatically created if an atmVclEntry with qbPktIotIfConfVpi and qbPktIotIfConfVci values does not exist. This corresponding entry can be removed only if the qbPktIotIfConfEntry is removed. The qbPktIotIfConfIndex of this table is an ifIndex of the DWS interface from the ifTable.
OBJECT-TYPE    
  QbIotPktIfConfEntry  

qbIotPktIfConfIndex 1.3.6.1.4.1.4323.2.3.1.3.1.1.1
An interface index of the Ethernet port interface.
OBJECT-TYPE    
  InterfaceIndex  

qbAtmIfIndex 1.3.6.1.4.1.4323.2.3.1.3.1.1.2
An interface index of the ATM interface that is stacked on top of the WAN/SONET interface.
OBJECT-TYPE    
  InterfaceIndex  

qbIotPktIfConfVpi 1.3.6.1.4.1.4323.2.3.1.3.1.1.3
A VPI of the AAL5 PVC that connects this interface to the ATM cloud. This PVC is automatically configured at the SONET port of the WAN card (atmVclTable).
OBJECT-TYPE    
  AtmVpIdentifier  

qbIotPktIfConfVci 1.3.6.1.4.1.4323.2.3.1.3.1.1.4
A VCI of the AAL5 bi-directional PVC that connects this interface to the ATM cloud. This PVC is automatically configured or removed at the SONET port of the WAN card (atmVclTable).
OBJECT-TYPE    
  AtmVcIdentifier  

qbIotPktIfConfConnName 1.3.6.1.4.1.4323.2.3.1.3.1.1.5
The textual name of the connection(PVC) as specified by a user. It provides a non-volatile handle for this PVC. The supplied name in the qbPktIotIfConfPvcName is associated with the same PVC for as long as that PVC/conection remains.
OBJECT-TYPE    
  DisplayString SIZE(1..20)  

qbIotPktIfConfRxTrafficDescrIndex 1.3.6.1.4.1.4323.2.3.1.3.1.1.6
The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the transmit direction of this VCL.
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

qbIotPktIfConfTxTrafficDescrIndex 1.3.6.1.4.1.4323.2.3.1.3.1.1.7
The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this VCL.
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

qbIotPktIfConfAdminStatus 1.3.6.1.4.1.4323.2.3.1.3.1.1.8
The desired administrative status of the packet connection The up and down states indicate that the traffic flow is enabled or disabled respectively across the ATM cloud.
OBJECT-TYPE    
  AtmVorXAdminStatus  

qbIotPktIfConfOperStatus 1.3.6.1.4.1.4323.2.3.1.3.1.1.9
The current operational status of the connect.
OBJECT-TYPE    
  AtmVorXOperStatus  

qbIotPktIfConfRowStatus 1.3.6.1.4.1.4323.2.3.1.3.1.1.10
The status column for this IOT ENET interface. This OBJECT can be set to: createAndGo(4) destroy(6) The following values may be read: active(1) This object may only be set to createAndGo(4). Setting this object to active(1) when its value is already active(1) is a no-op. Setting this object to createAndGo(4) causes the agent to attempt to create and commit the row based on the contents of the objects in the row. If all necessary information is present in the row and the values are acceptable to the agent, the agent will change the status to active(1). If any of the necessary objects are not available, the agent will reject the creation request. Setting this object to destroy(6) will remove the corresponding entry in this table, and disable data traffic.
OBJECT-TYPE    
  RowStatus  

qbIotPktIfConfLoopback 1.3.6.1.4.1.4323.2.3.1.3.1.1.11
This object enables loopback on the IOT ENET enedpoint.
OBJECT-TYPE    
  QbEnableStatus  

qbIotPktIfConfConnKind 1.3.6.1.4.1.4323.2.3.1.3.1.1.12
The PVC connection type.
OBJECT-TYPE    
  QbPvcConnKind  

qbIotAddrGroup 1.3.6.1.4.1.4323.2.3.1.4
OBJECT IDENTIFIER    

qbIotAddrTable 1.3.6.1.4.1.4323.2.3.1.4.1
The Quantum Bridge IOT address table. This table contains information to convert an IOT's address into an IOT's serial number. This table has two indexes: 1. Interface index of the IOAS interface to which a terminal connects. The interface identified by a particular value of this index is the same as the interface identified by the same value of ifIndex. 2. IOT terminal address. A row exists in this table for each discovered IOT terminal. Whenever an IOT is discovered a row is added to the table
OBJECT-TYPE    
  SEQUENCE OF  
    QbIotAddrEntry

qbIotAddrEntry 1.3.6.1.4.1.4323.2.3.1.4.1.1
For every IOT terminal there is a row in this table. This contains the IOT address and serial number.
OBJECT-TYPE    
  QbIotAddrEntry  

qbIotAddr 1.3.6.1.4.1.4323.2.3.1.4.1.1.1
The IOT's address.
OBJECT-TYPE    
  Integer32  

qbIotSerialNum 1.3.6.1.4.1.4323.2.3.1.4.1.1.2
The IOT's serial number.
OBJECT-TYPE    
  QbSerialNum  

qbIotPortCrossConnGroup 1.3.6.1.4.1.4323.2.3.1.5
OBJECT IDENTIFIER    

qbIotPortCrossConnTable 1.3.6.1.4.1.4323.2.3.1.5.1
The Quantum Bridge IOT port cross-connection table. This table defines all IOT port point-to-point cross-connections within a single OAS system. The connection can be set between two Ethernet, two DS1 or two E1 ports on different IOTs. The table has two indexes: the interface index of the first end-point and the interface index of the second endpoint. Note: Connections that are listed in this table are not reflected in the atmVclTable.
OBJECT-TYPE    
  SEQUENCE OF  
    QbIotPortCrossConnEntry

qbIotPortCrossConnEntry 1.3.6.1.4.1.4323.2.3.1.5.1.1
An entry in the Quantum Bridge qbIotPortConnTable two contains a connection between the same port type of different IOTs.
OBJECT-TYPE    
  QbIotPortCrossConnEntry  

qbIotPortCrossConnEndpt1IfIndex 1.3.6.1.4.1.4323.2.3.1.5.1.1.1
The ifIndex of the first IOT port((end-point) for the configured IOT cross-connect.
OBJECT-TYPE    
  InterfaceIndex  

qbIotPortCrossConnEndpt2IfIndex 1.3.6.1.4.1.4323.2.3.1.5.1.1.2
The ifIndex of the second IOT port(end-point) for the configured IOT cross-connect.
OBJECT-TYPE    
  InterfaceIndex  

qbIotPortCrossConnAdminStatus 1.3.6.1.4.1.4323.2.3.1.5.1.1.3
The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this VCL.
OBJECT-TYPE    
  AtmVorXAdminStatus  

qbIotPortCrossConnOperStatus 1.3.6.1.4.1.4323.2.3.1.5.1.1.4
The current operational status of the connection.
OBJECT-TYPE    
  AtmVorXOperStatus  

qbIotPortCrossConnLastChange 1.3.6.1.4.1.4323.2.3.1.5.1.1.5
The value of sysUpTime at the time this connection entered its current operational state.
OBJECT-TYPE    
  AtmVorXLastChange  

qbIotPortCrossConnRxTrafficDescrIndex 1.3.6.1.4.1.4323.2.3.1.5.1.1.6
The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the transmit direction of this connection.
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

qbIotPortCrossConnTxTrafficDescrIndex 1.3.6.1.4.1.4323.2.3.1.5.1.1.7
The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this connection.
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

qbIotPortCrossConnName 1.3.6.1.4.1.4323.2.3.1.5.1.1.8
The textual name of the connection as specified by a user. It provides a non-volatile handle for this connection. The supplied name in the qbIotPortConnName is associated with the same connection for as long as that conection remains.
OBJECT-TYPE    
  DisplayString SIZE(0..20)  

qbIotPortCrossConnRowStatus 1.3.6.1.4.1.4323.2.3.1.5.1.1.9
The status of the port connect entry. Changing the value of this object from 'active' to 'destroy' will remove this entry from the database. It will disrupt traffic between two IOT packet interfaces.
OBJECT-TYPE    
  RowStatus  

qbIotPortCrossConnLoopback 1.3.6.1.4.1.4323.2.3.1.5.1.1.10
This object enables loopback on this IOT to IOT port enedpoint. The endpoint on which loopback is enabled is defined by qbIotPortCrossConnLoopbackEndpt.
OBJECT-TYPE    
  QbEnableStatus  

qbIotPortCrossConnLoopbackEndpt 1.3.6.1.4.1.4323.2.3.1.5.1.1.11
This object defines loopback on the selected endpoint.
OBJECT-TYPE    
  INTEGER endPt1(1), endPt2(2)  

qbIotPortCrossConnKind 1.3.6.1.4.1.4323.2.3.1.5.1.1.12
The VCL connection type.
OBJECT-TYPE    
  QbPvcConnKind  

qbTContGroup 1.3.6.1.4.1.4323.2.3.1.6
OBJECT IDENTIFIER    

qbTContNumber 1.3.6.1.4.1.4323.2.3.1.6.1
The total number of provisioned Ethernet to ATM PVCs.
OBJECT-TYPE    
  Integer32  

qbNextFreeTContIndex 1.3.6.1.4.1.4323.2.3.1.6.2
The next available Container index.
OBJECT-TYPE    
  Integer32  

qbTContTable 1.3.6.1.4.1.4323.2.3.1.6.3
The Quantum Bridge Traffic Container table(TCons) contains traffic containers of IOTs.
OBJECT-TYPE    
  SEQUENCE OF  
    QbTContEntry

qbTContEntry 1.3.6.1.4.1.4323.2.3.1.6.3.1
An entry in the qbTContTable. There is one entry in the table per IOT on the PON for Release 3.0. The creation of a row in the qbSysIotTable causes a corresponding entry in this table to be automatically created. The deletion of a row in the qbSysIotTable causes a corresponding entry in this table to be automatically removed.
OBJECT-TYPE    
  QbTContEntry  

qbTContIndex 1.3.6.1.4.1.4323.2.3.1.6.3.1.1
The value of this object identifies the row of the Traffic Container Table. Note tht this value can be set to 1 only for Release 3.0.
OBJECT-TYPE    
  INTEGER  

qbTContType 1.3.6.1.4.1.4323.2.3.1.6.3.1.2
The Traffic container type. Note that this object can be set to type1 for Release 3.0
OBJECT-TYPE    
  INTEGER type1(1), type2(2), type3(3), type4(4), type5(5)  

qbTContMaxBw 1.3.6.1.4.1.4323.2.3.1.6.3.1.3
The maximum bandwidth to be assigned to this TCONT. Note that the read-only access is supported for Release 3.0
OBJECT-TYPE    
  INTEGER  

qbTContFixedBw 1.3.6.1.4.1.4323.2.3.1.6.3.1.4
The lower limit of bandwidth for this TCONT.
OBJECT-TYPE    
  INTEGER  

qbTContAssuredBw 1.3.6.1.4.1.4323.2.3.1.6.3.1.5
The guaranteed minimum bandwidth for this TCONT. TCONT. Note that the read-only access is supported for Release 3.0
OBJECT-TYPE    
  INTEGER  

qbTContGrantNum 1.3.6.1.4.1.4323.2.3.1.6.3.1.6
FSAN grant number that is assigned to this TCONT. Note that the read-only access is supported for Release 3.0
OBJECT-TYPE    
  INTEGER  

qbDwsNotifications 1.3.6.1.4.1.4323.2.3.2
OBJECT IDENTIFIER    

qbDwsNotificationPrefix 1.3.6.1.4.1.4323.2.3.2.0
OBJECT IDENTIFIER    

qbDwsIotRxLos 1.3.6.1.4.1.4323.2.3.2.0.1
A qbDwsIotRxLos trap indicates Loss of Signal by the IOT's. This trap is generated by an IOT when Analog DS1/E1 Analog or Digital Los occur.
NOTIFICATION-TYPE    
  qbDwsNetIfIndex  
  qbDwsIotIfAddr  

qbDwsRxIoasLos 1.3.6.1.4.1.4323.2.3.2.0.2
A qbDwsRxIoasLos trap indicates Loss of Signal by the IOAS's DWS receiver. This trap is generated by an IOAS DWS card when no signal from an IOT is detected within the timeslot window.
NOTIFICATION-TYPE    
  qbDwsNetIfIndex  
  qbDwsIotIfAddr  

qbDwsIoasTxFailure 1.3.6.1.4.1.4323.2.3.2.0.3
A qbDwsTxFailure trap indicates that the IOAS card transmitter does not work. The trap is generated by an IOAS card when the IOAS DWS card transmitter problem is detected. The trap contains the DWS card interface index.
NOTIFICATION-TYPE    
  qbDwsNetIfIndex  

qbDwsIotRangeTimeout 1.3.6.1.4.1.4323.2.3.2.0.4
A qbDwsTxFailure trap indicates that IOT not responding during the ranging process.
NOTIFICATION-TYPE    
  qbDwsNetIfIndex  
  qbDwsIotIfAddr  

qbDwsConformance 1.3.6.1.4.1.4323.2.3.3
OBJECT IDENTIFIER    

qbDwsCompliances 1.3.6.1.4.1.4323.2.3.3.1
OBJECT IDENTIFIER    

qbDwsCompliance 1.3.6.1.4.1.4323.2.3.3.1.1
The compliance statement for all agents that support this MIB. A compliant agent implements all objects defined in this MIB.
MODULE-COMPLIANCE    

qbDwsGroups 1.3.6.1.4.1.4323.2.3.3.2
OBJECT IDENTIFIER    

qbDwsNetGroupInfo 1.3.6.1.4.1.4323.2.3.3.2.1
The set of all accessible objects in the DWS Network Group of this MIB.
OBJECT-GROUP    

qbDwsIotGroupInfo 1.3.6.1.4.1.4323.2.3.3.2.2
The set of all accessible objects in the IOT Group of this MIB.
OBJECT-GROUP    

qbDwsPktGroupInfo 1.3.6.1.4.1.4323.2.3.3.2.3
The set of all accessible objects in the Packet Group ofthis MIB.
OBJECT-GROUP    

qbDwsIotAddrGroupInfo 1.3.6.1.4.1.4323.2.3.3.2.4
The set of all accessible objects in the IOT address group of this MIB.
OBJECT-GROUP    

Defined Objects

QbPvcConnKind  
A connection type that can be provisioned.
TEXTUAL-CONVENTION    
  INTEGER unknown(0), atmPvcToPvc(1), atmPvpToPvp(2), iotE1ToAtm(3), iotDs1ToAtm(4), iotEnetToAtm(5), vt15ToAtm(6), vc12ToAtm(7), vt15Vt15(8), vc12ToVc12(9), iotE1ToVt15(10), iotDs1ToVt15(11), iotE1ToVc12(12), iotDs1ToVc12(13), iotE1ToIotE1(14), iotDs1ToIotDs1(15), iotEnetToIotEnet(16), vc11ToAtm(17), iotDs1ToVc11(18), vc11ToVc11(19), m13ToAtm(20), iotDs1ToM13(21), m13ToM13(22), atmToEnet(23), atmToDs1(24), atmToE1(25), ds1ToVt15(26), e1ToVc12(27), ds1ToVc11(28), ds1ToM13(29), ds1ToDs1(30), e1ToE1(31), enetToEnet(32), iotDs1ToDs1(33), iotE1ToE1(34), iotEnetToEnet(35), vlanToAtm(36), vlanToGige(37), vlanToIotEnet(38), vlanToEnet(39)  

QbBitRate  
A data rate in bits/second.
TEXTUAL-CONVENTION    
  Gauge32  

QbSerialNum  
The IOT serial number.
TEXTUAL-CONVENTION    
  Unsigned32 0..32  

QbDwsIfStatus  
The status of the DWS Interface
TEXTUAL-CONVENTION    
  INTEGER ok(1), rxFailure(2), txFailure(3), unknown(4)  

QbDwsSrvStatus  
The service status of the DWS Interface
TEXTUAL-CONVENTION    
  INTEGER avilable(1), empty(2), almostFull(3), overflown(4)  

QbAtmAal5EncapsType  
The type of data encapsulation used over the AAL5 layer.
TEXTUAL-CONVENTION    
  INTEGER qbVcMultiplexRoutedProto(1), qbBridgedProto8023EncapFcs(2), qbBridgedProto8023EncapsNoFcs(3), qbBridgedPropEncaps(4), qbBridgedProtoLLCEncapsNoFcs(5), qbRoutedEncapsNoHdrNoFcs(6)  

QbEnableStatus  
enable(1) or disable(1) operations.
TEXTUAL-CONVENTION    
  INTEGER enable(1), disable(2)  

QbDwsNetEntry  
SEQUENCE    
  InterfaceIndex as qbDwsNetIfIndex  
  QbBitRate as qbDwsNetBw  
  QbBitRate as qbDwsNetAllocatedBw  
  QbBitRate as qbDwsNetAvailableBw  
  QbBitRate as qbDwsNetAllocatedUbrBw  
  QbBitRate as qbDwsNetAllocatedCbrBw  
  Integer32 as qbDwsNetNumCbrConn  
  Integer32 as qbDwsNetNumUbrConn  
  Integer32 as qbDwsNetNumIot  
  QbDwsIfStatus as qbDwsNetTxStatus  
  TimeStamp as qbDwsNetTxStatusLastChange  
  Integer32 as qbDwsNetLosIotAddr  
  TimeStamp as qbDwsNetLosIotTime  
  TruthValue as qbDwsNetEncryptStatus  
  INTEGER as qbDwsNetRangeMode  
  Counter32 as qbDwsNetRxTsCount  
  Counter32 as qbDwsNetTxTsCount  
  Counter32 as qbDwsNetRxMissingTs  
  Counter32 as qbDwsNetRxIllegalTs  
  Counter32 as qbDwsNetTxJabberTs  
  Counter32 as qbDwsNetTxOutOfFrameTs  
  Counter32 as qbDwsNetTxHdrCrcTsErrs  
  Counter32 as qbDwsNetOamRequests  
  Counter32 as qbDwsNetOamResponses  
  Counter32 as qbDwsNetOamEvents  
  Counter32 as qbDwsNetOamBadMsgs  
  INTEGER as qbDwsNetLoopBack  

QbDwsIotIfConfEntry  
SEQUENCE    
  InterfaceIndex as qbDwsIotIfIndex  
  InterfaceIndex as qbDwsIotNetIfIndex  
  Integer32 as qbDwsIotIfAddr  
  Integer32 as qbDwsIotIfConfPowerLevel  
  TimeTicks as qbDwsIotIfConfEqDelay  
  Integer32 as qbDwsIotIfConfWaveLength  
  QbBitRate as qbDwsIotIfUbrBw  
  QbBitRate as qbDwsIotIfCbrBw  
  QbDwsIfStatus as qbDwsIotIfTxStatus  
  TimeStamp as qbDwsIotIfTxStatusLastChange  
  TimeStamp as qbDwsIotIfLastRangeTime  

QbDwsIotIfStatsEntry  
SEQUENCE    
  INTEGER as qbDwsIotIfStatsUtil  
  Counter32 as qbDwsIotIfStatsOamRequests  
  Counter32 as qbDwsIotIfStatsOamResponses  
  Counter32 as qbDwsIotIfStatsOamEvents  
  Counter32 as qbDwsIotIfStatsOamBadMsgs  
  Counter32 as qbDwsIotIfStatsCrcErrs  
  Counter32 as qbDwsIotIfStatsTsHdrParityErrs  
  Counter32 as qbDwsIotIfStatsFrameLossErrs  
  Counter32 as qbDwsIotIfStatsSignalLossErrs  
  Counter32 as qbDwsIotIfStatsRxAal1Cells  
  Counter32 as qbDwsIotIfStatsTxAal1Cells  

QbIotPktIfConfEntry  
SEQUENCE    
  InterfaceIndex as qbIotPktIfConfIndex  
  InterfaceIndex as qbAtmIfIndex  
  AtmVpIdentifier as qbIotPktIfConfVpi  
  AtmVcIdentifier as qbIotPktIfConfVci  
  DisplayString as qbIotPktIfConfConnName  
  AtmTrafficDescrParamIndex as qbIotPktIfConfRxTrafficDescrIndex  
  AtmTrafficDescrParamIndex as qbIotPktIfConfTxTrafficDescrIndex  
  AtmVorXAdminStatus as qbIotPktIfConfAdminStatus  
  AtmVorXOperStatus as qbIotPktIfConfOperStatus  
  RowStatus as qbIotPktIfConfRowStatus  
  QbEnableStatus as qbIotPktIfConfLoopback  
  QbPvcConnKind as qbIotPktIfConfConnKind  

QbIotAddrEntry  
SEQUENCE    
  Integer32 as qbIotAddr  
  QbSerialNum as qbIotSerialNum  

QbIotPortCrossConnEntry  
SEQUENCE    
  InterfaceIndex as qbIotPortCrossConnEndpt1IfIndex  
  InterfaceIndex as qbIotPortCrossConnEndpt2IfIndex  
  AtmVorXAdminStatus as qbIotPortCrossConnAdminStatus  
  AtmVorXOperStatus as qbIotPortCrossConnOperStatus  
  AtmVorXLastChange as qbIotPortCrossConnLastChange  
  AtmTrafficDescrParamIndex as qbIotPortCrossConnRxTrafficDescrIndex  
  AtmTrafficDescrParamIndex as qbIotPortCrossConnTxTrafficDescrIndex  
  DisplayString as qbIotPortCrossConnName  
  RowStatus as qbIotPortCrossConnRowStatus  
  QbEnableStatus as qbIotPortCrossConnLoopback  
  INTEGER as qbIotPortCrossConnLoopbackEndpt  
  QbPvcConnKind as qbIotPortCrossConnKind  

QbTContEntry  
SEQUENCE    
  INTEGER as qbTContIndex  
  INTEGER as qbTContType  
  INTEGER as qbTContMaxBw  
  INTEGER as qbTContFixedBw  
  INTEGER as qbTContAssuredBw  
  INTEGER as qbTContGrantNum