RAPID-IPSEC-SA-MON-MIB-EXT

File: RAPID-IPSEC-SA-MON-MIB-EXT.mib (82072 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC RFC1213-MIB
IPSEC-ISAKMP-IKE-DOI-TC RAPID-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Gauge32 Integer32 NOTIFICATION-TYPE
IpAddress OBJECT-IDENTITY enterprises
TEXTUAL-CONVENTION TruthValue ifIndex
IpsecDoiIdentType IpsecDoiEncapsulationMode IpsecDoiEspTransform
IpsecDoiAhTransform IpsecDoiAuthAlgorithm IpsecDoiIpcompTransform
IpsecDoiSecProtocolId rapidstream

Defined Objects

rsIpsecSaMonModule 1.3.6.1.4.1.4355.3
The MIB module describes generic IPSec objects defined in IETF working draft 'draft-ieft-ipsec-monitor-mib-01' and RapidStream's extension.
MODULE-IDENTITY    

rsIpsecSaMonitorMIB 1.3.6.1.4.1.4355.3.1
This is the base object identifier for all IPSec branches.
OBJECT-IDENTITY    

rsSaTables 1.3.6.1.4.1.4355.3.1.1
This is the base object identifier for all SA tables.
OBJECT-IDENTITY    

rsIpsecSaEspInTable 1.3.6.1.4.1.4355.3.1.1.1
The (conceptual) table containing information on IPSec inbound ESP SAs. There should be one row for every inbound ESP security association that exists in the entity. The maximum number of rows is implementation dependent.
OBJECT-TYPE    
  SEQUENCE OF  
    RSIpsecSaEspInEntry

rsIpsecSaEspInEntry 1.3.6.1.4.1.4355.3.1.1.1.1
An entry (conceptual row) containing the information on a particular IPSec inbound ESP SA. A row in this table cannot be created or deleted by SNMP operations on columns of the table.
OBJECT-TYPE    
  RSIpsecSaEspInEntry  

rsIpsecSaEspInAddress 1.3.6.1.4.1.4355.3.1.1.1.1.1
The destination address of the SA. For implementations that do not support IPv6, this address should appear as one of the IPv4-mapped IPv6 addresses as defined in Section 2.5.4 of [IPV6AA]. Specifically, the prefix '0000:0000:0000:0000:0000:FFFF:' is used for IPv4 only nodes, while the prefix '0000:0000:0000:0000:0000:0000:' is used for bi-lingual nodes.
OBJECT-TYPE    
  IpAddress  

rsIpsecSaEspInSpi 1.3.6.1.4.1.4355.3.1.1.1.1.2
The security parameters index of the SA.
OBJECT-TYPE    
  Integer32  

rsIpsecSaEspInDestId 1.3.6.1.4.1.4355.3.1.1.1.1.3
The destination identifier of the SA, or 0 if unknown or if the SA uses transport mode encapsulation. This value is taken directly from the optional ID payloads that are exchanged during SA creation negotiation.
OBJECT-TYPE    
  OCTET STRING SIZE(1..255)  

rsIpsecSaEspInDestIdType 1.3.6.1.4.1.4355.3.1.1.1.1.4
The type of identifier presented by 'rsIpsecSaEspInDestId', or 0 if unknown or if the SA uses transport mode encapsulation.
OBJECT-TYPE    
  IpsecDoiIdentType  

rsIpsecSaEspInSourceId 1.3.6.1.4.1.4355.3.1.1.1.1.5
The source identifier of the SA, or 0 if unknown or if the SA uses transport mode encapsulation. This value is taken directly from the optional ID payloads that are exchange during SA creation negotiation.
OBJECT-TYPE    
  OCTET STRING SIZE(1..255)  

rsIpsecSaEspInSourceIdType 1.3.6.1.4.1.4355.3.1.1.1.1.6
The type of identifier presented by 'rsIpsecSaEspInSourceId', or 0 if unknown or if the SA uses transport mode encapsulation.
OBJECT-TYPE    
  IpsecDoiIdentType  

rsIpsecSaEspInProtocol 1.3.6.1.4.1.4355.3.1.1.1.1.7
The transport-layer protocol number that this SA carries, or 0 if it carries any protocol.
OBJECT-TYPE    
  Integer32 0..255  

rsIpsecSaEspInDestPort 1.3.6.1.4.1.4355.3.1.1.1.1.8
The destination port number of the protocol that this SA carries, or 0 if it carries any port number.
OBJECT-TYPE    
  Integer32 0..65535  

rsIpsecSaEspInSourcePort 1.3.6.1.4.1.4355.3.1.1.1.1.9
The source port number of the protocol that this SA carries, or 0 if it carries any port number.
OBJECT-TYPE    
  Integer32 0..65535  

rsIpsecSaEspInCreator 1.3.6.1.4.1.4355.3.1.1.1.1.10
The creator of this SA. This MIB makes no assumptions about how the SAs are created. They may be created statically, or by a key exchange protocol such as IKE, or by some other method.
OBJECT-TYPE    
  IpsecSaCreatorIdent  

rsIpsecSaEspInEncapsulation 1.3.6.1.4.1.4355.3.1.1.1.1.11
The type of encapsulation used by this SA.
OBJECT-TYPE    
  IpsecDoiEncapsulationMode  

rsIpsecSaEspInEncAlg 1.3.6.1.4.1.4355.3.1.1.1.1.12
A unique value representing the encryption algorithm applied to traffic or 0 if there is no encryption used.
OBJECT-TYPE    
  IpsecDoiEspTransform  

rsIpsecSaEspInEncKeyLength 1.3.6.1.4.1.4355.3.1.1.1.1.13
The length of the encryption key in bits used for the algorithm specified in the 'rsIpsecSaEspInEncAlg' object, or 0 if the key length is implicit in the specified algorithm or there is no encryption specified.
OBJECT-TYPE    
  Integer32 0..65531  

rsIpsecSaEspInAuthAlg 1.3.6.1.4.1.4355.3.1.1.1.1.14
A unique value representing the hash algorithm applied to traffic or 0 if there is no authentication used.
OBJECT-TYPE    
  IpsecDoiAuthAlgorithm  

rsIpsecSaEspInLimitSeconds 1.3.6.1.4.1.4355.3.1.1.1.1.15
The maximum lifetime in seconds of the SA, or 0 if there is no time constraint on its expiration. The display value is limited to 4294967295 seconds (more than 136 years); values greater than that value will be truncated.
OBJECT-TYPE    
  Integer32  

rsIpsecSaEspInLimitKbytes 1.3.6.1.4.1.4355.3.1.1.1.1.16
The maximum traffic in kilobytes that the SA is allowed to support, or 0 if there is no traffic constraint on its expiration. The display value is limited to 4294967295 kilobytes; values greater than that value will be truncated.
OBJECT-TYPE    
  Integer32  

rsIpsecSaEspInAccSeconds 1.3.6.1.4.1.4355.3.1.1.1.1.17
The number of seconds accumulated against the SA's expiration by time. This is also the number of seconds that the SA has existed.
OBJECT-TYPE    
  Counter32  

rsIpsecSaEspInAccKbytes 1.3.6.1.4.1.4355.3.1.1.1.1.18
The amount of traffic accumulated that counts against the SA's expiration by traffic limitation, measured in Kbytes. This value may be 0 if the SA does not expire based on traffic.
OBJECT-TYPE    
  Counter32  

rsIpsecSaEspInUserOctets 1.3.6.1.4.1.4355.3.1.1.1.1.19
The amount of user level traffic measured in bytes handled by the SA. This is not necessarily the same as the amount of traffic applied against the traffic expiration limit.
OBJECT-TYPE    
  Counter32  

rsIpsecSaEspInPackets 1.3.6.1.4.1.4355.3.1.1.1.1.20
The number of packets handled by the SA.
OBJECT-TYPE    
  Counter32  

rsIpsecSaEspInDecryptErrors 1.3.6.1.4.1.4355.3.1.1.1.1.21
The number of packets discarded by the SA due to decryption errors.
OBJECT-TYPE    
  Counter32  

rsIpsecSaEspInAuthErrors 1.3.6.1.4.1.4355.3.1.1.1.1.22
The number of packets discarded by the SA due to authentication errors.
OBJECT-TYPE    
  Counter32  

rsIpsecSaEspInReplayErrors 1.3.6.1.4.1.4355.3.1.1.1.1.23
The number of packets discarded by the SA due to replay errors.
OBJECT-TYPE    
  Counter32  

rsIpsecSaEspInPolicyErrors 1.3.6.1.4.1.4355.3.1.1.1.1.24
The number of packets discarded by the SA due to policy errors. This includes packets where the next protocol is invalid.
OBJECT-TYPE    
  Counter32  

rsIpsecSaEspInPadErrors 1.3.6.1.4.1.4355.3.1.1.1.1.25
The number of packets discarded by the SA due to pad value errors. Implementations that do not check this must not support this object.
OBJECT-TYPE    
  Counter32  

rsIpsecSaEspInOtherReceiveErrors 1.3.6.1.4.1.4355.3.1.1.1.1.26
The number of packets discarded by the SA due to errors other than decryption, authentication or replay errors. This may include packets dropped due to a lack of receive buffers, and may include packets dropped due to congestion at the decryption element.
OBJECT-TYPE    
  Counter32  

rsIpsecSaAhInTable 1.3.6.1.4.1.4355.3.1.1.2
The (conceptual) table containing information on IPSec inbound AH SAs. There should be one row for every inbound AH security association that exists in the entity. The maximum number of rows is implementation dependent.
OBJECT-TYPE    
  SEQUENCE OF  
    RSIpsecSaAhInEntry

rsIpsecSaAhInEntry 1.3.6.1.4.1.4355.3.1.1.2.1
An entry (conceptual row) containing the information on a particular IPSec inbound AH SA. A row in this table cannot be created or deleted by SNMP operations on columns of the table.
OBJECT-TYPE    
  RSIpsecSaAhInEntry  

rsIpsecSaAhInAddress 1.3.6.1.4.1.4355.3.1.1.2.1.1
The destination address of the SA. For implementations that do not support IPv6, this address should appear as one of the IPv4-mapped IPv6 addresses as defined in Section 2.5.4 of [IPV6AA]. Specifically, the prefix '0000:0000:0000:0000:0000:FFFF:' is used for IPv4 only nodes, while the prefix '0000:0000:0000:0000:0000:0000:' is used for bi-lingual nodes.
OBJECT-TYPE    
  IpAddress  

rsIpsecSaAhInSpi 1.3.6.1.4.1.4355.3.1.1.2.1.2
The security parameters index of the SA.
OBJECT-TYPE    
  Integer32  

rsIpsecSaAhInDestId 1.3.6.1.4.1.4355.3.1.1.2.1.3
The destination identifier of the SA, or 0 if unknown or if the SA uses transport mode encapsulation. This value is taken directly from the optional ID payloads that are exchange during SA creation negotiation.
OBJECT-TYPE    
  OCTET STRING SIZE(1..255)  

rsIpsecSaAhInDestIdType 1.3.6.1.4.1.4355.3.1.1.2.1.4
The type of identifier presented by 'rsIpsecSaAhInDestId', or 0 if unknown or if the SA uses transport mode encapsulation.
OBJECT-TYPE    
  IpsecDoiIdentType  

rsIpsecSaAhInSourceId 1.3.6.1.4.1.4355.3.1.1.2.1.5
The source identifier of the SA, or 0 if unknown or if the SA uses transport mode encapsulation. This value is taken directly from the optional ID payloads that are exchange during SA creation negotiation.
OBJECT-TYPE    
  OCTET STRING SIZE(1..255)  

rsIpsecSaAhInSourceIdType 1.3.6.1.4.1.4355.3.1.1.2.1.6
The type of identifier presented by 'rsIpsecSaAhInSourceId', or 0 if unknown or if the SA uses transport mode encapsulation.
OBJECT-TYPE    
  IpsecDoiIdentType  

rsIpsecSaAhInProtocol 1.3.6.1.4.1.4355.3.1.1.2.1.7
The transport-layer protocol number that this SA carries, or 0 if it carries any protocol.
OBJECT-TYPE    
  Integer32 0..255  

rsIpsecSaAhInDestPort 1.3.6.1.4.1.4355.3.1.1.2.1.8
The destination port number of the protocol that this SA carries, or 0 if it carries any port number.
OBJECT-TYPE    
  Integer32 0..65535  

rsIpsecSaAhInSourcePort 1.3.6.1.4.1.4355.3.1.1.2.1.9
The source port number of the protocol that this SA carries, or 0 if it carries any port number.
OBJECT-TYPE    
  Integer32 0..65535  

rsIpsecSaAhInCreator 1.3.6.1.4.1.4355.3.1.1.2.1.10
The creator of this SA. This MIB makes no assumptions about how the SAs are created. They may be created statically, or by a key exchange protocol such as IKE, or by some other method.
OBJECT-TYPE    
  IpsecSaCreatorIdent  

rsIpsecSaAhInEncapsulation 1.3.6.1.4.1.4355.3.1.1.2.1.11
The type of encapsulation used by this SA.
OBJECT-TYPE    
  IpsecDoiEncapsulationMode  

rsIpsecSaAhInAuthAlg 1.3.6.1.4.1.4355.3.1.1.2.1.12
A unique value representing the hash algorithm applied to traffic carried by this SA if it uses ESP or 0 if there is no authentication applied by ESP.
OBJECT-TYPE    
  IpsecDoiAhTransform  

rsIpsecSaAhInLimitSeconds 1.3.6.1.4.1.4355.3.1.1.2.1.13
The maximum lifetime in seconds of the SA, or 0 if there is no time constraint on its expiration. The display value is limited to 4294967295 seconds (more than 136 years); values greater than that value will be truncated.
OBJECT-TYPE    
  Integer32  

rsIpsecSaAhInLimitKbytes 1.3.6.1.4.1.4355.3.1.1.2.1.14
The maximum traffic in Kbytes that the SA is allowed to support, or 0 if there is no traffic constraint on its expiration. The display value is limited to 4294967295 kilobytes; values greater than that value will be truncated.
OBJECT-TYPE    
  Integer32  

rsIpsecSaAhInAccSeconds 1.3.6.1.4.1.4355.3.1.1.2.1.15
The number of seconds accumulated against the SA's expiration by time. This is also the number of seconds that the SA has existed.
OBJECT-TYPE    
  Counter32  

rsIpsecSaAhInAccKbytes 1.3.6.1.4.1.4355.3.1.1.2.1.16
The amount of traffic accumulated that counts against the SA's expiration by traffic limitation, measured in Kbytes. This value may be 0 if the SA does not expire based on traffic.
OBJECT-TYPE    
  Counter32  

rsIpsecSaAhInUserOctets 1.3.6.1.4.1.4355.3.1.1.2.1.17
The amount of user level traffic measured in bytes handled by the SA. This is not necessarily the same as the amount of traffic applied against the traffic expiration limit.
OBJECT-TYPE    
  Counter32  

rsIpsecSaAhInPackets 1.3.6.1.4.1.4355.3.1.1.2.1.18
The number of packets handled by the SA.
OBJECT-TYPE    
  Counter32  

rsIpsecSaAhInAuthErrors 1.3.6.1.4.1.4355.3.1.1.2.1.19
The number of packets discarded by the SA due to authentication errors.
OBJECT-TYPE    
  Counter32  

rsIpsecSaAhInReplayErrors 1.3.6.1.4.1.4355.3.1.1.2.1.20
The number of packets discarded by the SA due to replay errors.
OBJECT-TYPE    
  Counter32  

rsIpsecSaAhInPolicyErrors 1.3.6.1.4.1.4355.3.1.1.2.1.21
The number of packets discarded by the SA due to policy errors. This includes packets where the next protocol is invalid.
OBJECT-TYPE    
  Counter32  

rsIpsecSaAhInOtherReceiveErrors 1.3.6.1.4.1.4355.3.1.1.2.1.22
The number of packets discarded by the SA due to errors other than decryption, authentication or replay errors. This may include packets dropped due to a lack of receive buffers, and may include packets dropped due to congestion at the authentication element.
OBJECT-TYPE    
  Counter32  

rsIpsecSaIpcompInTable 1.3.6.1.4.1.4355.3.1.1.3
The (conceptual) table containing information on IPSec inbound IPCOMP SAs. There should be one row for every inbound IPCOMP (security) association that exists in the entity. The maximum number of rows is implementation dependent.
OBJECT-TYPE    
  SEQUENCE OF  
    RSIpsecSaIpcompInEntry

rsIpsecSaIpcompInEntry 1.3.6.1.4.1.4355.3.1.1.3.1
An entry (conceptual row) containing the information on a particular IPSec inbound IPCOMP SA. A row in this table cannot be created or deleted by SNMP operations on columns of the table.
OBJECT-TYPE    
  RSIpsecSaIpcompInEntry  

rsIpsecSaIpcompInAddress 1.3.6.1.4.1.4355.3.1.1.3.1.1
The destination address of the SA. For implementations that do not support IPv6, this address should appear as one of the IPv4-mapped IPv6 addresses as defined in Section 2.5.4 of [IPV6AA]. Specifically, the prefix '0000:0000:0000:0000:0000:FFFF:' is used for IPv4 only nodes, while the prefix '0000:0000:0000:0000:0000:0000:' is used for bi-lingual nodes.
OBJECT-TYPE    
  IpAddress  

rsIpsecSaIpcompInCpi 1.3.6.1.4.1.4355.3.1.1.3.1.2
The CPI of the SA. Since the lower values of CPIs are reserved to be the same as the algorithm, the syntax for this object is the same as the transform.
OBJECT-TYPE    
  IpsecDoiIpcompTransform  

rsIpsecSaIpcompInDestId 1.3.6.1.4.1.4355.3.1.1.3.1.3
The destination identifier of the SA, or 0 if unknown or if the SA uses transport mode, or 0 if this SA is used with multiple SAs in protection suites. This value, if non-zero, is taken directly from the optional ID payloads that are exchange during SA creation negotiation.
OBJECT-TYPE    
  OCTET STRING SIZE(1..255)  

rsIpsecSaIpcompInDestIdType 1.3.6.1.4.1.4355.3.1.1.3.1.4
The type of identifier presented by 'rsIpsecSaIpcompInDestId', or 0 if unknown or if the SA uses transport mode, or 0 if this SA is used with multiple SAs in protection suites.
OBJECT-TYPE    
  IpsecDoiIdentType  

rsIpsecSaIpcompInSourceId 1.3.6.1.4.1.4355.3.1.1.3.1.5
The source identifier of the SA, or 0 if unknown or if the SA uses transport mode encapsulation, or 0 if this SA is used with multiple SAs in protection suites. This value, if non-zero, is taken directly from the optional ID payloads that are exchange during SA creation negotiation.
OBJECT-TYPE    
  OCTET STRING SIZE(1..255)  

rsIpsecSaIpcompInSourceIdType 1.3.6.1.4.1.4355.3.1.1.3.1.6
The type of identifier presented by 'rsIpsecSaIpcompInSourceId', or 0 if unknown or if the SA uses transport mode encapsulation, or 0 if this SA is used with multiple SAs in protection suites.
OBJECT-TYPE    
  IpsecDoiIdentType  

rsIpsecSaIpcompInProtocol 1.3.6.1.4.1.4355.3.1.1.3.1.7
The transport-layer protocol number that this SA carries, or 0 if it carries any protocol.
OBJECT-TYPE    
  Integer32 0..255  

rsIpsecSaIpcompInDestPort 1.3.6.1.4.1.4355.3.1.1.3.1.8
The destination port number of the protocol that this SA carries, or 0 if it carries any port number.
OBJECT-TYPE    
  Integer32 0..65535  

rsIpsecSaIpcompInSourcePort 1.3.6.1.4.1.4355.3.1.1.3.1.9
The source port number of the protocol that this SA carries, or 0 if it carries any port number.
OBJECT-TYPE    
  Integer32 0..65535  

rsIpsecSaIpcompInCreator 1.3.6.1.4.1.4355.3.1.1.3.1.10
The creator of this SA. This MIB makes no assumptions about how the SAs are created. They may be created statically, or by a key exchange protocol such as IKE, or by some other method.
OBJECT-TYPE    
  IpsecSaCreatorIdent  

rsIpsecSaIpcompInEncapsulation 1.3.6.1.4.1.4355.3.1.1.3.1.11
The type of encapsulation used by this SA.
OBJECT-TYPE    
  IpsecDoiEncapsulationMode  

rsIpsecSaIpcompInDecompAlg 1.3.6.1.4.1.4355.3.1.1.3.1.12
A unique value representing the decompression algorithm applied to traffic.
OBJECT-TYPE    
  IpsecDoiIpcompTransform  

rsIpsecSaIpcompInSeconds 1.3.6.1.4.1.4355.3.1.1.3.1.13
The number of seconds that the SA has existed.
OBJECT-TYPE    
  Counter32  

rsIpsecSaIpcompInUserOctets 1.3.6.1.4.1.4355.3.1.1.3.1.14
The amount of user level traffic measured in bytes handled by the SA.
OBJECT-TYPE    
  Counter32  

rsIpsecSaIpcompInPackets 1.3.6.1.4.1.4355.3.1.1.3.1.15
The number of packets handled by the SA.
OBJECT-TYPE    
  Counter32  

rsIpsecSaIpcompInDecompErrors 1.3.6.1.4.1.4355.3.1.1.3.1.16
The number of packets discarded by the SA due to decompression errors.
OBJECT-TYPE    
  Counter32  

rsIpsecSaIpcompInOtherReceiveErrors 1.3.6.1.4.1.4355.3.1.1.3.1.17
The number of packets discarded by the SA due to errors other than decompression errors. This may include packets dropped due to a lack of receive buffers, and packets dropped due to congestion at the decompression element.
OBJECT-TYPE    
  Counter32  

rsIpsecSaEspOutTable 1.3.6.1.4.1.4355.3.1.1.4
The (conceptual) table containing information on IPSec Outbound ESP SAs. There should be one row for every outbound ESP security association that exists in the entity. The maximum number of rows is implementation dependent.
OBJECT-TYPE    
  SEQUENCE OF  
    RSIpsecSaEspOutEntry

rsIpsecSaEspOutEntry 1.3.6.1.4.1.4355.3.1.1.4.1
An entry (conceptual row) containing the information on a particular IPSec Outbound ESP SA. A row in this table cannot be created or deleted by SNMP operations on columns of the table.
OBJECT-TYPE    
  RSIpsecSaEspOutEntry  

rsIpsecSaEspOutAddress 1.3.6.1.4.1.4355.3.1.1.4.1.1
The destination address of the SA. For implementations that do not support IPv6, this address should appear as one of the IPv4-mapped IPv6 addresses as defined in Section 2.5.4 of [IPV6AA]. Specifically, the prefix '0000:0000:0000:0000:0000:FFFF:' is used for IPv4 only nodes, while the prefix '0000:0000:0000:0000:0000:0000:' is used for bi-lingual nodes.
OBJECT-TYPE    
  IpAddress  

rsIpsecSaEspOutSpi 1.3.6.1.4.1.4355.3.1.1.4.1.2
The security parameters index of the SA.
OBJECT-TYPE    
  Integer32  

rsIpsecSaEspOutSourceId 1.3.6.1.4.1.4355.3.1.1.4.1.3
The source identifier of the SA, or 0 if unknown or if the SA uses transport mode encapsulation. This value is taken directly from the optional ID payloads that are exchange during phase 2 negotiations.
OBJECT-TYPE    
  OCTET STRING SIZE(4..255)  

rsIpsecSaEspOutSourceIdType 1.3.6.1.4.1.4355.3.1.1.4.1.4
The type of identifier presented by 'rsIpsecSaEspOutSourceId', or 0 if unknown or if the SA uses transport mode encapsulation.
OBJECT-TYPE    
  IpsecDoiIdentType  

rsIpsecSaEspOutDestId 1.3.6.1.4.1.4355.3.1.1.4.1.5
The destination identifier of the SA, or 0 if unknown or if the SA uses transport mode encapsulation. This value is taken directly from the optional ID payloads that are exchange during phase 2 negotiations.
OBJECT-TYPE    
  OCTET STRING SIZE(4..255)  

rsIpsecSaEspOutDestIdType 1.3.6.1.4.1.4355.3.1.1.4.1.6
The type of identifier presented by 'rsIpsecSaEspOutDestId', or 0 if unknown or if the SA uses transport mode encapsulation.
OBJECT-TYPE    
  IpsecDoiIdentType  

rsIpsecSaEspOutProtocol 1.3.6.1.4.1.4355.3.1.1.4.1.7
The transport-layer protocol number that this SA carries, or 0 if it carries any protocol.
OBJECT-TYPE    
  Integer32 0..255  

rsIpsecSaEspOutSourcePort 1.3.6.1.4.1.4355.3.1.1.4.1.8
The source port number of the protocol that this SA carries, or 0 if it carries any port number.
OBJECT-TYPE    
  Integer32 0..65535  

rsIpsecSaEspOutDestPort 1.3.6.1.4.1.4355.3.1.1.4.1.9
The destination port number of the protocol that this SA carries, or 0 if it carries any port number.
OBJECT-TYPE    
  Integer32 0..65535  

rsIpsecSaEspOutCreator 1.3.6.1.4.1.4355.3.1.1.4.1.10
The creator of this SA. This MIB makes no assumptions about how the SAs are created. They may be created statically, or by a key exchange protocol such as IKE, or by some other method.
OBJECT-TYPE    
  IpsecSaCreatorIdent  

rsIpsecSaEspOutEncapsulation 1.3.6.1.4.1.4355.3.1.1.4.1.11
The type of encapsulation used by this SA.
OBJECT-TYPE    
  IpsecDoiEncapsulationMode  

rsIpsecSaEspOutEncAlg 1.3.6.1.4.1.4355.3.1.1.4.1.12
A unique value representing the encryption algorithm applied to traffic or 0 if there is no encryption used.
OBJECT-TYPE    
  IpsecDoiEspTransform  

rsIpsecSaEspOutEncKeyLength 1.3.6.1.4.1.4355.3.1.1.4.1.13
The length of the encryption key in bits used for the algorithm specified in the 'rsIpsecSaEspOutEncAlg' object, or 0 if the key length is implicit in the specified algorithm or there is no encryption specified.
OBJECT-TYPE    
  Integer32 0..65531  

rsIpsecSaEspOutAuthAlg 1.3.6.1.4.1.4355.3.1.1.4.1.14
A unique value representing the hash algorithm applied to traffic or 0 if there is no authentication used.
OBJECT-TYPE    
  IpsecDoiAuthAlgorithm  

rsIpsecSaEspOutLimitSeconds 1.3.6.1.4.1.4355.3.1.1.4.1.15
The maximum lifetime in seconds of the SA, or 0 if there is no time constraint on its expiration. The display value is limited to 4294967295 seconds (more than 136 years); values greater than that value will be truncated.
OBJECT-TYPE    
  Integer32  

rsIpsecSaEspOutLimitKbytes 1.3.6.1.4.1.4355.3.1.1.4.1.16
The maximum traffic in kbytes that the SA is allowed to support, or 0 if there is no traffic constraint on its expiration. The display value is limited to 4294967295 kilobytes; values greater than that value will be truncated.
OBJECT-TYPE    
  Integer32  

rsIpsecSaEspOutAccSeconds 1.3.6.1.4.1.4355.3.1.1.4.1.17
The number of seconds accumulated against the SA's expiration by time. This is also the number of seconds that the SA has existed.
OBJECT-TYPE    
  Counter32  

rsIpsecSaEspOutAccKbytes 1.3.6.1.4.1.4355.3.1.1.4.1.18
The amount of traffic accumulated that counts against the SA's expiration by traffic limitation, measured in Kbytes. This value may be 0 if the SA does not expire based on traffic.
OBJECT-TYPE    
  Counter32  

rsIpsecSaEspOutUserOctets 1.3.6.1.4.1.4355.3.1.1.4.1.19
The amount of user level traffic measured in bytes handled by the SA. This is not necessarily the same as the amount of traffic applied against the traffic expiration limit.
OBJECT-TYPE    
  Counter32  

rsIpsecSaEspOutPackets 1.3.6.1.4.1.4355.3.1.1.4.1.20
The number of packets handled by the SA.
OBJECT-TYPE    
  Counter32  

rsIpsecSaEspOutSendErrors 1.3.6.1.4.1.4355.3.1.1.4.1.21
The number of packets discarded by the SA due to any error. This may include errors due to a lack of transmit buffers.
OBJECT-TYPE    
  Counter32  

rsIpsecSaAhOutTable 1.3.6.1.4.1.4355.3.1.1.5
The (conceptual) table containing information on IPSec Outbound AH SAs. There should be one row for every outbound AH security association that exists in the entity. The maximum number of rows is implementation dependent.
OBJECT-TYPE    
  SEQUENCE OF  
    RSIpsecSaAhOutEntry

rsIpsecSaAhOutEntry 1.3.6.1.4.1.4355.3.1.1.5.1
An entry (conceptual row) containing the information on a particular IPSec Outbound AH SA. A row in this table cannot be created or deleted by SNMP operations on columns of the table.
OBJECT-TYPE    
  RSIpsecSaAhOutEntry  

rsIpsecSaAhOutAddress 1.3.6.1.4.1.4355.3.1.1.5.1.1
The destination address of the SA. For implementations that do not support IPv6, this address should appear as one of the IPv4-mapped IPv6 addresses as defined in Section 2.5.4 of [IPV6AA]. Specifically, the prefix '0000:0000:0000:0000:0000:FFFF:' is used for IPv4 only nodes, while the prefix '0000:0000:0000:0000:0000:0000:' is used for bi-lingual nodes.
OBJECT-TYPE    
  IpAddress  

rsIpsecSaAhOutSpi 1.3.6.1.4.1.4355.3.1.1.5.1.2
The security parameters index of the SA.
OBJECT-TYPE    
  Integer32  

rsIpsecSaAhOutSourceId 1.3.6.1.4.1.4355.3.1.1.5.1.3
The source identifier of the SA, or 0 if unknown or if the SA uses transport mode encapsulation. This value is taken directly from the optional ID payloads that are exchange during phase 2 negotiations.
OBJECT-TYPE    
  OCTET STRING SIZE(4..255)  

rsIpsecSaAhOutSourceIdType 1.3.6.1.4.1.4355.3.1.1.5.1.4
The type of identifier presented by 'rsIpsecSaAhOutSourceId', or 0 if unknown or if the SA uses transport mode encapsulation.
OBJECT-TYPE    
  IpsecDoiIdentType  

rsIpsecSaAhOutDestId 1.3.6.1.4.1.4355.3.1.1.5.1.5
The destination identifier of the SA, or 0 if unknown or if the SA uses transport mode encapsulation. This value is taken directly from the optional ID payloads that are exchange during phase 2 negotiations.
OBJECT-TYPE    
  OCTET STRING SIZE(4..255)  

rsIpsecSaAhOutDestIdType 1.3.6.1.4.1.4355.3.1.1.5.1.6
The type of identifier presented by 'rsIpsecSaAhOutDestId', or 0 if unknown or if the SA uses transport mode encapsulation.
OBJECT-TYPE    
  IpsecDoiIdentType  

rsIpsecSaAhOutProtocol 1.3.6.1.4.1.4355.3.1.1.5.1.7
The transport-layer protocol number that this SA carries, or 0 if it carries any protocol.
OBJECT-TYPE    
  Integer32 0..255  

rsIpsecSaAhOutSourcePort 1.3.6.1.4.1.4355.3.1.1.5.1.8
The source port number of the protocol that this SA carries, or 0 if it carries any port number.
OBJECT-TYPE    
  Integer32 0..65535  

rsIpsecSaAhOutDestPort 1.3.6.1.4.1.4355.3.1.1.5.1.9
The destination port number of the protocol that this SA carries, or 0 if it carries any port number.
OBJECT-TYPE    
  Integer32 0..65535  

rsIpsecSaAhOutCreator 1.3.6.1.4.1.4355.3.1.1.5.1.10
The creator of this SA. This MIB makes no assumptions about how the SAs are created. They may be created statically, or by a key exchange protocol such as IKE, or by some other method.
OBJECT-TYPE    
  IpsecSaCreatorIdent  

rsIpsecSaAhOutEncapsulation 1.3.6.1.4.1.4355.3.1.1.5.1.11
The type of encapsulation used by this SA.
OBJECT-TYPE    
  IpsecDoiEncapsulationMode  

rsIpsecSaAhOutAuthAlg 1.3.6.1.4.1.4355.3.1.1.5.1.12
A unique value representing the hash algorithm applied to traffic or 0 if there is no authentication used.
OBJECT-TYPE    
  IpsecDoiAhTransform  

rsIpsecSaAhOutLimitSeconds 1.3.6.1.4.1.4355.3.1.1.5.1.13
The maximum lifetime in seconds of the SA, or 0 if there is no time constraint on its expiration. The display value is limited to 4294967295 seconds (more than 136 years); values greater than that value will be truncated.
OBJECT-TYPE    
  Integer32  

rsIpsecSaAhOutLimitKbytes 1.3.6.1.4.1.4355.3.1.1.5.1.14
The maximum traffic in Kbytes that the SA is allowed to support, or 0 if there is no traffic constraint on its expiration. The display value is limited to 4294967295 kilobytes; values greater than that value will be truncated.
OBJECT-TYPE    
  Integer32  

rsIpsecSaAhOutAccSeconds 1.3.6.1.4.1.4355.3.1.1.5.1.15
The number of seconds accumulated against the SA's expiration by time. This is also the number of seconds that the SA has existed.
OBJECT-TYPE    
  Counter32  

rsIpsecSaAhOutAccKbytes 1.3.6.1.4.1.4355.3.1.1.5.1.16
The amount of traffic accumulated that counts against the SA's expiration by traffic limitation, measured in Kbytes. This value may be 0 if the SA does not expire based on traffic.
OBJECT-TYPE    
  Counter32  

rsIpsecSaAhOutUserOctets 1.3.6.1.4.1.4355.3.1.1.5.1.17
The amount of user level traffic measured in bytes handled by the SA. This is not necessarily the same as the amount of traffic applied against the traffic expiration limit.
OBJECT-TYPE    
  Counter32  

rsIpsecSaAhOutPackets 1.3.6.1.4.1.4355.3.1.1.5.1.18
The number of packets handled by the SA.
OBJECT-TYPE    
  Counter32  

rsIpsecSaAhOutSendErrors 1.3.6.1.4.1.4355.3.1.1.5.1.19
The number of packets discarded by the SA due to any error. This may include errors due to a lack of transmit buffers.
OBJECT-TYPE    
  Counter32  

rsIpsecSaIpcompOutTable 1.3.6.1.4.1.4355.3.1.1.6
The (conceptual) table containing information on IPSec Outbound IPCOMP SAs. There should be one row for every outbound IPCOMP (security) association that exists in the entity. The maximum number of rows is implementation dependent.
OBJECT-TYPE    
  SEQUENCE OF  
    RSIpsecSaIpcompOutEntry

rsIpsecSaIpcompOutEntry 1.3.6.1.4.1.4355.3.1.1.6.1
An entry (conceptual row) containing the information on a particular IPSec Outbound IPCOMP SA. A row in this table cannot be created or deleted by SNMP operations on columns of the table.
OBJECT-TYPE    
  RSIpsecSaIpcompOutEntry  

rsIpsecSaIpcompOutAddress 1.3.6.1.4.1.4355.3.1.1.6.1.1
The destination address of the SA. If the IPCOMP SA is shared across multiple SAs in protection suites, this value may be 0. For implementations that do not support IPv6, this address should appear as one of the IPv4-mapped IPv6 addresses as defined in Section 2.5.4 of [IPV6AA]. Specifically, the prefix '0000:0000:0000:0000:0000:FFFF:' is used for IPv4 only nodes, while the prefix '0000:0000:0000:0000:0000:0000:' is used for bi-lingual nodes.
OBJECT-TYPE    
  IpAddress  

rsIpsecSaIpcompOutCpi 1.3.6.1.4.1.4355.3.1.1.6.1.2
The CPI of the SA. Since the lower values of CPIs are reserved to be the same as the algorithm, the syntax for this object is the same as the transform.
OBJECT-TYPE    
  IpsecDoiIpcompTransform  

rsIpsecSaIpcompOutSourceId 1.3.6.1.4.1.4355.3.1.1.6.1.3
The source identifier of the SA, or 0 if unknown or if the SA uses transport mode encapsulation, or 0 if this SA is used with multiple SAs in protection suites. This value, if non-zero, is taken directly from the optional ID payloads that are exchange during phase 2 negotiations.
OBJECT-TYPE    
  OCTET STRING SIZE(4..255)  

rsIpsecSaIpcompOutSourceIdType 1.3.6.1.4.1.4355.3.1.1.6.1.4
The type of identifier presented by 'rsIpsecSaIpcompOutSourceId', or 0 if unknown or if the SA uses transport mode encapsulation, or 0 if this SA is used with multiple SAs in protection suites.
OBJECT-TYPE    
  IpsecDoiIdentType  

rsIpsecSaIpcompOutDestId 1.3.6.1.4.1.4355.3.1.1.6.1.5
The destination identifier of the SA, or 0 if unknown or if the SA uses transport mode encapsulation, or 0 if this SA is used with multiple SAs in protection suites. This value, if non-zero, is taken directly from the optional ID payloads that are exchange during phase 2 negotiations.
OBJECT-TYPE    
  OCTET STRING SIZE(4..255)  

rsIpsecSaIpcompOutDestIdType 1.3.6.1.4.1.4355.3.1.1.6.1.6
The type of identifier presented by 'rsIpsecSaIpcompOutDestId', or 0 if unknown or if the SA uses transport mode encapsulation, or 0 if this SA is used with multiple SAs in protection suites.
OBJECT-TYPE    
  IpsecDoiIdentType  

rsIpsecSaIpcompOutProtocol 1.3.6.1.4.1.4355.3.1.1.6.1.7
The transport-layer protocol number that this SA carries, or 0 if it carries any protocol.
OBJECT-TYPE    
  Integer32 0..255  

rsIpsecSaIpcompOutSourcePort 1.3.6.1.4.1.4355.3.1.1.6.1.8
The source port number of the protocol that this SA carries, or 0 if it carries any port number.
OBJECT-TYPE    
  Integer32 0..65535  

rsIpsecSaIpcompOutDestPort 1.3.6.1.4.1.4355.3.1.1.6.1.9
The destination port number of the protocol that this SA carries, or 0 if it carries any port number.
OBJECT-TYPE    
  Integer32 0..65535  

rsIpsecSaIpcompOutCreator 1.3.6.1.4.1.4355.3.1.1.6.1.10
The creator of this SA. This MIB makes no assumptions about how the SAs are created. They may be created statically, or by a key exchange protocol such as IKE, or by some other method.
OBJECT-TYPE    
  IpsecSaCreatorIdent  

rsIpsecSaIpcompOutEncapsulation 1.3.6.1.4.1.4355.3.1.1.6.1.11
The type of encapsulation used by this SA.
OBJECT-TYPE    
  IpsecDoiEncapsulationMode  

rsIpsecSaIpcompOutCompAlg 1.3.6.1.4.1.4355.3.1.1.6.1.12
A unique value representing the compression algorithm applied to traffic.
OBJECT-TYPE    
  IpsecDoiIpcompTransform  

rsIpsecSaIpcompOutSeconds 1.3.6.1.4.1.4355.3.1.1.6.1.13
The number of seconds that the SA has existed.
OBJECT-TYPE    
  Counter32  

rsIpsecSaIpcompOutUserOctets 1.3.6.1.4.1.4355.3.1.1.6.1.14
The amount of user level traffic measured in bytes handled by the SA. This is not necessarily the same as the amount of traffic applied against the traffic expiration limit.
OBJECT-TYPE    
  Counter32  

rsIpsecSaIpcompOutPackets 1.3.6.1.4.1.4355.3.1.1.6.1.15
The number of packets handled by the SA.
OBJECT-TYPE    
  Counter32  

rsSaStatistics 1.3.6.1.4.1.4355.3.1.2
This is the base object identifier for all objects which are global counters for IPSec security associations.
OBJECT-IDENTITY    

rsIpsecEspCurrentInboundSAs 1.3.6.1.4.1.4355.3.1.2.1
The current number of inbound ESP SAs in the entity.
OBJECT-TYPE    
  Gauge32  

rsIpsecEspTotalInboundSAs 1.3.6.1.4.1.4355.3.1.2.2
The total number of inbound ESP SAs created in the entity since boot time.
OBJECT-TYPE    
  Counter32  

rsIpsecEspCurrentOutboundSAs 1.3.6.1.4.1.4355.3.1.2.3
The current number of outbound ESP SAs in the entity.
OBJECT-TYPE    
  Gauge32  

rsIpsecEspTotalOutboundSAs 1.3.6.1.4.1.4355.3.1.2.4
The total number of outbound ESP SAs created in the entity since boot time.
OBJECT-TYPE    
  Counter32  

rsIpsecAhCurrentInboundSAs 1.3.6.1.4.1.4355.3.1.2.5
The current number of inbound AH SAs in the entity.
OBJECT-TYPE    
  Gauge32  

rsIpsecAhTotalInboundSAs 1.3.6.1.4.1.4355.3.1.2.6
The total number of inbound AH SAs created in the entity since boot time.
OBJECT-TYPE    
  Counter32  

rsIpsecAhCurrentOutboundSAs 1.3.6.1.4.1.4355.3.1.2.7
The current number of outbound AH SAs in the entity.
OBJECT-TYPE    
  Gauge32  

rsIpsecAhTotalOutboundSAs 1.3.6.1.4.1.4355.3.1.2.8
The total number of outbound AH SAs created in the entity since boot time.
OBJECT-TYPE    
  Counter32  

rsIpsecIpcompCurrentInboundSAs 1.3.6.1.4.1.4355.3.1.2.9
The current number of inbound IPCOMP SAs in the entity.
OBJECT-TYPE    
  Gauge32  

rsIpsecIpcompTotalInboundSAs 1.3.6.1.4.1.4355.3.1.2.10
The total number of inbound IPCOMP SAs created in the entity since boot time.
OBJECT-TYPE    
  Counter32  

rsIpsecIpcompCurrentOutboundSAs 1.3.6.1.4.1.4355.3.1.2.11
The current number of outbound IPCOMP SAs in the entity.
OBJECT-TYPE    
  Gauge32  

rsIpsecIpcompTotalOutboundSAs 1.3.6.1.4.1.4355.3.1.2.12
The total number of outbound IPCOMP SAs created in the entity since boot time.
OBJECT-TYPE    
  Counter32  

rsSaErrors 1.3.6.1.4.1.4355.3.1.3
This is the base object identifier for all objects which are global error counters for IPSec security associations.
OBJECT-IDENTITY    

rsIpsecDecryptionErrors 1.3.6.1.4.1.4355.3.1.3.1
The total number of packets received by the entity in SAs since boot time with decryption errors.
OBJECT-TYPE    
  Counter32  

rsIpsecAuthenticationErrors 1.3.6.1.4.1.4355.3.1.3.2
The total number of packets received by the entity in SAs since boot time with authentication errors. This includes all packets in which the hash value is determined to be invalid, for both ESP and AH SAs.
OBJECT-TYPE    
  Counter32  

rsIpsecReplayErrors 1.3.6.1.4.1.4355.3.1.3.3
The total number of packets received by the entity in SAs since boot time with replay errors.
OBJECT-TYPE    
  Counter32  

rsIpsecPolicyErrors 1.3.6.1.4.1.4355.3.1.3.4
The total number of packets received by the entity in SAs since boot time and discarded due to policy errors. This includes packets that had selectors that were invalid for the SA that carried them.
OBJECT-TYPE    
  Counter32  

rsIpsecOtherReceiveErrors 1.3.6.1.4.1.4355.3.1.3.5
The total number of packets received by the entity in SAs since boot time and discarded due to errors not due to decryption, authentication, replay or policy.
OBJECT-TYPE    
  Counter32  

rsIpsecSendErrors 1.3.6.1.4.1.4355.3.1.3.6
The total number of packets to be sent by the entity in SAs since boot time and discarded due to errors.
OBJECT-TYPE    
  Counter32  

rsIpsecUnknownSpiErrors 1.3.6.1.4.1.4355.3.1.3.7
The total number of packets received by the entity since boot time with SPIs or CPIs that were not valid.
OBJECT-TYPE    
  Counter32  

rsSaTraps 1.3.6.1.4.1.4355.3.1.4
This is the base object identifier for all objects which are traps for IPSec security associations.
OBJECT-IDENTITY    

rsEspAuthFailureTrap 1.3.6.1.4.1.4355.3.1.4.0.1
IPSec packets with invalid hashes were found in an inbound ESP SA. The total number of authentication errors accumulated is sent for the specific row of the 'rsIpsecSaEspInTable' table for the SA; this provides the identity of the SA in which the error occurred. Implementations SHOULD send one trap per SA (within a reasonable time period), rather than sending one trap per packet.
NOTIFICATION-TYPE    
  rsIpsecSaEspInAuthErrors  

rsAhAuthFailureTrap 1.3.6.1.4.1.4355.3.1.4.0.2
IPSec packets with invalid hashes were found in an inbound AH SA. The total number of authentication errors accumulated is sent for the specific row of the 'rsIpsecSaAhInTable' table for the SA; this provides the identity of the SA in which the error occurred. Implementations SHOULD send one trap per SA (within a reasonable time period), rather than sending one trap per packet.
NOTIFICATION-TYPE    
  rsIpsecSaAhInAuthErrors  

rsEspReplayFailureTrap 1.3.6.1.4.1.4355.3.1.4.0.3
IPSec packets with invalid sequence numbers were found in an inbound ESP SA. The total number of replay errors accumulated is sent for the specific row of the 'rsIpsecSaEspInTable' table for the SA; this provides the identity of the SA in which the error occurred. Implementations SHOULD send one trap per SA (within a reasonable time period), rather than sending one trap per packet.
NOTIFICATION-TYPE    
  rsIpsecSaEspInReplayErrors  

rsAhReplayFailureTrap 1.3.6.1.4.1.4355.3.1.4.0.4
IPSec packets with invalid sequence numbers were found in the specified AH SA. The total number of replay errors accumulated is sent for the specific row of the 'rsIpsecSaAhInTable' table for the SA; this provides the identity of the SA in which the error occurred. Implementations SHOULD send one trap per SA (within a reasonable time period), rather than sending one trap per packet.
NOTIFICATION-TYPE    
  rsIpsecSaAhInReplayErrors  

rsEspPolicyFailureTrap 1.3.6.1.4.1.4355.3.1.4.0.5
IPSec packets carrying packets with invalid selectors for the specified ESP SA were found. The total number of policy errors accumulated is sent for the specific row of the 'rsIpsecSaEspInTable' table for the SA; this provides the identity of the SA in which the error occurred. Implementations SHOULD send one trap per SA (within a reasonable time period), rather than sending one trap per packet.
NOTIFICATION-TYPE    
  rsIpsecSaEspInPolicyErrors  

rsAhPolicyFailureTrap 1.3.6.1.4.1.4355.3.1.4.0.6
IPSec packets carrying packets with invalid selectors for the specified AH SA were found. The total number of policy errors accumulated is sent for the specific row of the 'rsIpsecSaAhInTable' table for the SA; this provides the identity of the SA in which the error occurred. Implementations SHOULD send one trap per SA (within a reasonable time period), rather than sending one trap per packet.
NOTIFICATION-TYPE    
  rsIpsecSaAhInPolicyErrors  

rsInvalidSpiTrap 1.3.6.1.4.1.4355.3.1.4.0.7
A packet with an unknown SPI was detected from the specified peer with the specified SPI using the specified protocol. The destination address of the received packet is specified by 'ipsecLocalAddress'. The value 'ifIndex' may be 0 if this optional linkage is unsupported. If the object 'ipsecSecurityProtocol' has the value for IPCOMP, then the 'ipsecSPI' object is the CPI of the packet. Implementations SHOULD send one trap per peer (within a reasonable time period), rather than sending one trap per packet.
NOTIFICATION-TYPE    
  rsIpsecLocalAddress  
  rsIpsecSecurityProtocol  
  rsIpsecPeerAddress  
  rsIpsecSPI  
  ifIndex  

rsSaTrapObjects 1.3.6.1.4.1.4355.3.1.5
This is the base object identifier for objects which are used as part of traps.
OBJECT-IDENTITY    

rsIpsecSecurityProtocol 1.3.6.1.4.1.4355.3.1.5.1
A security protocol associated with the trap.
OBJECT-TYPE    
  IpsecDoiSecProtocolId  

rsIpsecSPI 1.3.6.1.4.1.4355.3.1.5.2
An SPI associated with a trap. Where the security protocol associated with the trap is IPCOMP, this value has a maximum of 65535.
OBJECT-TYPE    
  Integer32  

rsIpsecLocalAddress 1.3.6.1.4.1.4355.3.1.5.3
A local IP address associated with the trap.
OBJECT-TYPE    
  IpAddress  

rsIpsecPeerAddress 1.3.6.1.4.1.4355.3.1.5.4
A peer IP address associated with the trap.
OBJECT-TYPE    
  IpAddress  

rsSaTrapControl 1.3.6.1.4.1.4355.3.1.6
This is the base object identifier for all objects which are trap controls for IPSec security associations.
OBJECT-IDENTITY    

rsEspAuthFailureTrapEnable 1.3.6.1.4.1.4355.3.1.6.1
Indicates whether espAuthFailureTrap traps should be generated.
OBJECT-TYPE    
  TruthValue  

rsAhAuthFailureTrapEnable 1.3.6.1.4.1.4355.3.1.6.2
Indicates whether ahAuthFailureTrap traps should be generated.
OBJECT-TYPE    
  TruthValue  

rsEspReplayFailureTrapEnable 1.3.6.1.4.1.4355.3.1.6.3
Indicates whether espReplayFailureTrap traps should be generated.
OBJECT-TYPE    
  TruthValue  

rsAhReplayFailureTrapEnable 1.3.6.1.4.1.4355.3.1.6.4
Indicates whether ahReplayFailureTrap traps should be generated.
OBJECT-TYPE    
  TruthValue  

rsEspPolicyFailureTrapEnable 1.3.6.1.4.1.4355.3.1.6.5
Indicates whether espPolicyFailureTrap traps should be generated.
OBJECT-TYPE    
  TruthValue  

rsAhPolicyFailureTrapEnable 1.3.6.1.4.1.4355.3.1.6.6
Indicates whether ahPolicyFailureTrap traps should be generated.
OBJECT-TYPE    
  TruthValue  

rsInvalidSpiTrapEnable 1.3.6.1.4.1.4355.3.1.6.7
Indicates whether invalidSpiTrap traps should be generated.
OBJECT-TYPE    
  TruthValue  

rsSaGroups 1.3.6.1.4.1.4355.3.1.7
This is the base object identifier for all objects which describe the groups in this MIB.
OBJECT-IDENTITY    

rsSaConformance 1.3.6.1.4.1.4355.3.1.8
This is the base object identifier for all objects which describe the conformance for this MIB.
OBJECT-IDENTITY    

Defined Objects

IpsecSaCreatorIdent  
A value indicating how an SA was created.
TEXTUAL-CONVENTION    
  INTEGER unknown(0), static(1), ike(2), other(3)  

IpsecIpv6Address  
This data type is used to model IPv6 address prefixes. This is a binary string of 16 octets in network byte-order.
TEXTUAL-CONVENTION    
  OCTET STRING SIZE(16)  

RSIpsecSaEspInEntry  
SEQUENCE    
  IpAddress as rsIpsecSaEspInAddress  
  Integer32 as rsIpsecSaEspInSpi  
  OCTET STRING as rsIpsecSaEspInDestId  
  IpsecDoiIdentType as rsIpsecSaEspInDestIdType  
  OCTET STRING as rsIpsecSaEspInSourceId  
  IpsecDoiIdentType as rsIpsecSaEspInSourceIdType  
  Integer32 as rsIpsecSaEspInProtocol  
  Integer32 as rsIpsecSaEspInDestPort  
  Integer32 as rsIpsecSaEspInSourcePort  
  IpsecSaCreatorIdent as rsIpsecSaEspInCreator  
  IpsecDoiEncapsulationMode as rsIpsecSaEspInEncapsulation  
  IpsecDoiEspTransform as rsIpsecSaEspInEncAlg  
  Integer32 as rsIpsecSaEspInEncKeyLength  
  IpsecDoiAuthAlgorithm as rsIpsecSaEspInAuthAlg  
  Integer32 as rsIpsecSaEspInLimitSeconds  
  Integer32 as rsIpsecSaEspInLimitKbytes  
  Counter32 as rsIpsecSaEspInAccSeconds  
  Counter32 as rsIpsecSaEspInAccKbytes  
  Counter32 as rsIpsecSaEspInUserOctets  
  Counter32 as rsIpsecSaEspInPackets  
  Counter32 as rsIpsecSaEspInDecryptErrors  
  Counter32 as rsIpsecSaEspInAuthErrors  
  Counter32 as rsIpsecSaEspInReplayErrors  
  Counter32 as rsIpsecSaEspInPolicyErrors  
  Counter32 as rsIpsecSaEspInPadErrors  
  Counter32 as rsIpsecSaEspInOtherReceiveErrors  

RSIpsecSaAhInEntry  
SEQUENCE    
  IpAddress as rsIpsecSaAhInAddress  
  Integer32 as rsIpsecSaAhInSpi  
  OCTET STRING as rsIpsecSaAhInDestId  
  IpsecDoiIdentType as rsIpsecSaAhInDestIdType  
  OCTET STRING as rsIpsecSaAhInSourceId  
  IpsecDoiIdentType as rsIpsecSaAhInSourceIdType  
  Integer32 as rsIpsecSaAhInProtocol  
  Integer32 as rsIpsecSaAhInDestPort  
  Integer32 as rsIpsecSaAhInSourcePort  
  IpsecSaCreatorIdent as rsIpsecSaAhInCreator  
  IpsecDoiEncapsulationMode as rsIpsecSaAhInEncapsulation  
  IpsecDoiAhTransform as rsIpsecSaAhInAuthAlg  
  Integer32 as rsIpsecSaAhInLimitSeconds  
  Integer32 as rsIpsecSaAhInLimitKbytes  
  Counter32 as rsIpsecSaAhInAccSeconds  
  Counter32 as rsIpsecSaAhInAccKbytes  
  Counter32 as rsIpsecSaAhInUserOctets  
  Counter32 as rsIpsecSaAhInPackets  
  Counter32 as rsIpsecSaAhInAuthErrors  
  Counter32 as rsIpsecSaAhInReplayErrors  
  Counter32 as rsIpsecSaAhInPolicyErrors  
  Counter32 as rsIpsecSaAhInOtherReceiveErrors  

RSIpsecSaIpcompInEntry  
SEQUENCE    
  IpAddress as rsIpsecSaIpcompInAddress  
  IpsecDoiIpcompTransform as rsIpsecSaIpcompInCpi  
  OCTET STRING as rsIpsecSaIpcompInDestId  
  IpsecDoiIdentType as rsIpsecSaIpcompInDestIdType  
  OCTET STRING as rsIpsecSaIpcompInSourceId  
  IpsecDoiIdentType as rsIpsecSaIpcompInSourceIdType  
  Integer32 as rsIpsecSaIpcompInProtocol  
  Integer32 as rsIpsecSaIpcompInDestPort  
  Integer32 as rsIpsecSaIpcompInSourcePort  
  IpsecSaCreatorIdent as rsIpsecSaIpcompInCreator  
  IpsecDoiEncapsulationMode as rsIpsecSaIpcompInEncapsulation  
  IpsecDoiIpcompTransform as rsIpsecSaIpcompInDecompAlg  
  Counter32 as rsIpsecSaIpcompInSeconds  
  Counter32 as rsIpsecSaIpcompInUserOctets  
  Counter32 as rsIpsecSaIpcompInPackets  
  Counter32 as rsIpsecSaIpcompInDecompErrors  
  Counter32 as rsIpsecSaIpcompInOtherReceiveErrors  

RSIpsecSaEspOutEntry  
SEQUENCE    
  IpAddress as rsIpsecSaEspOutAddress  
  Integer32 as rsIpsecSaEspOutSpi  
  OCTET STRING as rsIpsecSaEspOutSourceId  
  IpsecDoiIdentType as rsIpsecSaEspOutSourceIdType  
  OCTET STRING as rsIpsecSaEspOutDestId  
  IpsecDoiIdentType as rsIpsecSaEspOutDestIdType  
  Integer32 as rsIpsecSaEspOutProtocol  
  Integer32 as rsIpsecSaEspOutSourcePort  
  Integer32 as rsIpsecSaEspOutDestPort  
  IpsecSaCreatorIdent as rsIpsecSaEspOutCreator  
  IpsecDoiEncapsulationMode as rsIpsecSaEspOutEncapsulation  
  IpsecDoiEspTransform as rsIpsecSaEspOutEncAlg  
  Integer32 as rsIpsecSaEspOutEncKeyLength  
  IpsecDoiAuthAlgorithm as rsIpsecSaEspOutAuthAlg  
  Integer32 as rsIpsecSaEspOutLimitSeconds  
  Integer32 as rsIpsecSaEspOutLimitKbytes  
  Counter32 as rsIpsecSaEspOutAccSeconds  
  Counter32 as rsIpsecSaEspOutAccKbytes  
  Counter32 as rsIpsecSaEspOutUserOctets  
  Counter32 as rsIpsecSaEspOutPackets  
  Counter32 as rsIpsecSaEspOutSendErrors  

RSIpsecSaAhOutEntry  
SEQUENCE    
  IpAddress as rsIpsecSaAhOutAddress  
  Integer32 as rsIpsecSaAhOutSpi  
  OCTET STRING as rsIpsecSaAhOutSourceId  
  IpsecDoiIdentType as rsIpsecSaAhOutSourceIdType  
  OCTET STRING as rsIpsecSaAhOutDestId  
  IpsecDoiIdentType as rsIpsecSaAhOutDestIdType  
  Integer32 as rsIpsecSaAhOutProtocol  
  Integer32 as rsIpsecSaAhOutSourcePort  
  Integer32 as rsIpsecSaAhOutDestPort  
  IpsecSaCreatorIdent as rsIpsecSaAhOutCreator  
  IpsecDoiEncapsulationMode as rsIpsecSaAhOutEncapsulation  
  IpsecDoiAhTransform as rsIpsecSaAhOutAuthAlg  
  Integer32 as rsIpsecSaAhOutLimitSeconds  
  Integer32 as rsIpsecSaAhOutLimitKbytes  
  Counter32 as rsIpsecSaAhOutAccSeconds  
  Counter32 as rsIpsecSaAhOutAccKbytes  
  Counter32 as rsIpsecSaAhOutUserOctets  
  Counter32 as rsIpsecSaAhOutPackets  
  Counter32 as rsIpsecSaAhOutSendErrors  

RSIpsecSaIpcompOutEntry  
SEQUENCE    
  IpAddress as rsIpsecSaIpcompOutAddress  
  IpsecDoiIpcompTransform as rsIpsecSaIpcompOutCpi  
  OCTET STRING as rsIpsecSaIpcompOutSourceId  
  IpsecDoiIdentType as rsIpsecSaIpcompOutSourceIdType  
  OCTET STRING as rsIpsecSaIpcompOutDestId  
  IpsecDoiIdentType as rsIpsecSaIpcompOutDestIdType  
  Integer32 as rsIpsecSaIpcompOutProtocol  
  Integer32 as rsIpsecSaIpcompOutSourcePort  
  Integer32 as rsIpsecSaIpcompOutDestPort  
  IpsecSaCreatorIdent as rsIpsecSaIpcompOutCreator  
  IpsecDoiEncapsulationMode as rsIpsecSaIpcompOutEncapsulation  
  IpsecDoiIpcompTransform as rsIpsecSaIpcompOutCompAlg  
  Counter32 as rsIpsecSaIpcompOutSeconds  
  Counter32 as rsIpsecSaIpcompOutUserOctets  
  Counter32 as rsIpsecSaIpcompOutPackets