REDSTONE-ATM-MIB

File: REDSTONE-ATM-MIB.mib (26608 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
IF-MIB REDSTONE-SMI REDSTONE-TC

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
OBJECT-GROUP MODULE-COMPLIANCE RowStatus
InterfaceIndex InterfaceIndexOrZero rsMgmt
RsNextIfIndex

Defined Objects

rsAtmMIB 1.3.6.1.4.1.2773.2.8
The ATM MIB for the Redstone Communications Inc. enterprise.
MODULE-IDENTITY    

rsAtmObjects 1.3.6.1.4.1.2773.2.8.1
OBJECT IDENTIFIER    

rsAtmIfLayer 1.3.6.1.4.1.2773.2.8.1.1
OBJECT IDENTIFIER    

rsAtmNextIfIndex 1.3.6.1.4.1.2773.2.8.1.1.1
Coordinate ifIndex value allocation for entries in rsAtmIfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
OBJECT-TYPE    
  RsNextIfIndex  

rsAtmIfTable 1.3.6.1.4.1.2773.2.8.1.1.2
This table contains entries for ATM interfaces present in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    RsAtmIfEntry

rsAtmIfEntry 1.3.6.1.4.1.2773.2.8.1.1.2.1
Each entry describes the characteristics of an ATM interface. Creating/deleting entries in this table causes corresponding entries for be created /deleted in ifTable/ifXTable/rsIfTable.
OBJECT-TYPE    
  RsAtmIfEntry  

rsAtmIfIndex 1.3.6.1.4.1.2773.2.8.1.1.2.1.1
The ifIndex of the ATM interface. When creating entries in this table, suitable values for this object are determined by reading rsAtmNextIfIndex.
OBJECT-TYPE    
  InterfaceIndex  

rsAtmIfRowStatus 1.3.6.1.4.1.2773.2.8.1.1.2.1.2
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: rsAtmIfRowStatus rsAtmIfLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for rsAtmIfIndex must have been determined previously, by reading rsAtmNextIfIndex. A corresponding entry in ifTable/ifXTable/rsIfTable is created/destroyed as a result of creating/destroying an entry in this table.
OBJECT-TYPE    
  RowStatus  

rsAtmIfLowerIfIndex 1.3.6.1.4.1.2773.2.8.1.1.2.1.3
The ifIndex of an interface over which this ATM interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
OBJECT-TYPE    
  InterfaceIndexOrZero  

rsAtmIfIlmiVpi 1.3.6.1.4.1.2773.2.8.1.1.2.1.4
The VPI of the Ilmi of a major ATM interface.
OBJECT-TYPE    
  Integer32 0..255  

rsAtmIfIlmiVci 1.3.6.1.4.1.2773.2.8.1.1.2.1.5
The VCI of the Ilmi of a major ATM interface.
OBJECT-TYPE    
  Integer32 0..65535  

rsAtmIfIlmiVcd 1.3.6.1.4.1.2773.2.8.1.1.2.1.6
An integer identifier for the Ilmi, used in conjunction with the command-line interface. The value must be unique among VCs configured on the same ATM interface.
OBJECT-TYPE    
  Integer32 0..65535  

rsAtmIfIlmiPollFrequency 1.3.6.1.4.1.2773.2.8.1.1.2.1.7
Use to set the Interim Local Management Interface (ILMI) keepalive timer. This value sets the allowable time between POLL PDU transmissions if there are no pending sequence data PDUs. Use the value 0 to disable ILMI keepalives.
OBJECT-TYPE    
  Integer32  

rsAtmIfIlmiAdminState 1.3.6.1.4.1.2773.2.8.1.1.2.1.8
The administrative status of ILMI in the ATM interface.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

rsAtmIfUniVersion 1.3.6.1.4.1.2773.2.8.1.1.2.1.9
Use to specify the User Network Interface (UNI) the router should use when ILMI link auto determination is unsuccesful or ILMI is disabled.
OBJECT-TYPE    
  INTEGER version3Dot0(0), version3Dot1(1), version4Dot0(2)  

rsAtmAal5IfLayer 1.3.6.1.4.1.2773.2.8.1.2
OBJECT IDENTIFIER    

rsAtmAal5NextIfIndex 1.3.6.1.4.1.2773.2.8.1.2.1
Coordinate ifIndex value allocation for entries in rsAtmAal5IfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
OBJECT-TYPE    
  RsNextIfIndex  

rsAtmAal5IfTable 1.3.6.1.4.1.2773.2.8.1.2.2
This table contains entries for ATM AAL5 interfaces present in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    RsAtmAal5IfEntry

rsAtmAal5IfEntry 1.3.6.1.4.1.2773.2.8.1.2.2.1
Each entry describes the characteristics of an ATM AAL5 interface. Creating/deleting entries in this table causes corresponding entries for be created /deleted in ifTable/ifXTable/rsIfTable.
OBJECT-TYPE    
  RsAtmAal5IfEntry  

rsAtmAal5IfIndex 1.3.6.1.4.1.2773.2.8.1.2.2.1.1
The ifIndex of the ATM AAL5 interface. When creating entries in this table, suitable values for this object are determined by reading rsAtmAal5NextIfIndex.
OBJECT-TYPE    
  InterfaceIndex  

rsAtmAal5IfRowStatus 1.3.6.1.4.1.2773.2.8.1.2.2.1.2
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: rsAtmAal5IfRowStatus rsAtmAal5IfLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for rsAtmAal5IfIndex must have been determined previously, by reading rsAtmAal5NextIfIndex. A corresponding entry in ifTable/ifXTable/rsIfTable is created/destroyed as a result of creating/destroying an entry in this table.
OBJECT-TYPE    
  RowStatus  

rsAtmAal5IfLowerIfIndex 1.3.6.1.4.1.2773.2.8.1.2.2.1.3
The ifIndex of an ATM interface over which this ATM AAL5 interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
OBJECT-TYPE    
  InterfaceIndexOrZero  

rsAtmSubIfLayer 1.3.6.1.4.1.2773.2.8.1.3
OBJECT IDENTIFIER    

rsAtmSubIfNextIfIndex 1.3.6.1.4.1.2773.2.8.1.3.1
Coordinate ifIndex value allocation for entries in rsAtmSubIfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
OBJECT-TYPE    
  RsNextIfIndex  

rsAtmSubIfTable 1.3.6.1.4.1.2773.2.8.1.3.2
This table contains entries for ATM Subinterfaces present in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    RsAtmSubIfEntry

rsAtmSubIfEntry 1.3.6.1.4.1.2773.2.8.1.3.2.1
Each entry describes the characteristics of an ATM Subinterface. Creating/deleting entries in this table causes corresponding entries for be created /deleted in ifTable/ifXTable/rsIfTable.
OBJECT-TYPE    
  RsAtmSubIfEntry  

rsAtmSubIfIndex 1.3.6.1.4.1.2773.2.8.1.3.2.1.1
The ifIndex of the ATM Subinterface. When creating entries in this table, suitable values for this object are determined by reading rsAtmSubNextIfIndex.
OBJECT-TYPE    
  InterfaceIndex  

rsAtmSubIfRowStatus 1.3.6.1.4.1.2773.2.8.1.3.2.1.2
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: rsAtmSubIfRowStatus rsAtmSubIfLowerIndex In addition, when creating an entry the following conditions must hold: A value for rsAtmSubIfIndex must have been determined previously, by reading rsAtmSubIfNextIfIndex. A corresponding entry in ifTable/ifXTable/rsIfTable is created/destroyed as a result of creating/destroying an entry in this table.
OBJECT-TYPE    
  RowStatus  

rsAtmSubIfDistinguisher 1.3.6.1.4.1.2773.2.8.1.3.2.1.3
An integer identifier for the sub interface, used in conjunction with the command-line interface. It is provided here for cross-reference purposes only. The value must be unique among sub interfaces configured on the same underlying ATM adaptation layer. The upper bound for the value is further constrained to be identical with the maximum number of sub interfaces supported by the lower interface. If this object is not configured, a value will be allocated internally and can be queried after table entry creation has succeeded.
OBJECT-TYPE    
  Integer32  

rsAtmSubIfLowerIfIndex 1.3.6.1.4.1.2773.2.8.1.3.2.1.4
The ifIndex of an ATM AAL5 interface over which this ATM Subinterface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
OBJECT-TYPE    
  InterfaceIndexOrZero  

rsAtmSubIfVccTable 1.3.6.1.4.1.2773.2.8.1.3.3
This table contains entries for ATM VCCs configured on ATM Subinterfaces present in the system. An implementation may constrain the number of VCCs permitted to be configured per ATM Subinterface; in particular, an implementation may restrict each ATM Subinterface to have a single VCC. Attributes in this entry can only be configured at entry creation, and remain fixed for the lifetime of the entry.
OBJECT-TYPE    
  SEQUENCE OF  
    RsAtmSubIfVccEntry

rsAtmSubIfVccEntry 1.3.6.1.4.1.2773.2.8.1.3.3.1
Each entry describes the characteristics of an ATM Subinterface VCC.
OBJECT-TYPE    
  RsAtmSubIfVccEntry  

rsAtmSubIfVccVpi 1.3.6.1.4.1.2773.2.8.1.3.3.1.1
The VPI of the ATM VCC used by this subinterface.
OBJECT-TYPE    
  Integer32 0..255  

rsAtmSubIfVccVci 1.3.6.1.4.1.2773.2.8.1.3.3.1.2
The VCI of the ATM VCC used by this subinterface.
OBJECT-TYPE    
  Integer32 0..65535  

rsAtmSubIfVccRowStatus 1.3.6.1.4.1.2773.2.8.1.3.3.1.3
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: rsAtmSubIfVccRowStatus In addition, when creating an entry the following conditions must hold: The ATM Subinterface identified by rsAtmSubIfIndex must exist. A positive value configured for rsAtmSubIfVccVcd must not already be assigned to an existing VCC. For each value of rsAtmSubIfVccServiceCategory, additional dependent objects in the entry require configuration as identified here: rsAtmSubIfVccServiceCategory Requires configuration of: ------------------------------------------------------------ ubr ubrPcr rsAtmSubIfVccPcr nrtVbr rsAtmSubIfVccPcr rsAtmSubIfVccScr rsAtmSubIfVccMbs ------------------------------------------------------------ Attributes in this entry can only be configured at entry creation, and remain fixed for the lifetime of the entry.
OBJECT-TYPE    
  RowStatus  

rsAtmSubIfVccVcd 1.3.6.1.4.1.2773.2.8.1.3.3.1.4
An integer identifier for the circuit, used in conjunction with the command-line interface. It is provided here for cross-reference purposes only. The value must be unique among VCCs configured on the same underlying ATM interface. The upper bound for the value is further constrained to be identical with the maximum number of VCCs supported by the underlying ATM interface. If this object is not configured, or is configured with a value of zero, a value will be allocated internally and can be queried after table entry creation has succeeded.
OBJECT-TYPE    
  Integer32 0..65535  

rsAtmSubIfVccType 1.3.6.1.4.1.2773.2.8.1.3.3.1.5
Specifies the encapsulation used by the circuit to carry IP datagrams. Encapsulations are as specified in RFC1483 Multiprotocol Interconnect over ATM.
OBJECT-TYPE    
  INTEGER rfc1483VcMux(0), rfc1483Llc(1)  

rsAtmSubIfVccServiceCategory 1.3.6.1.4.1.2773.2.8.1.3.3.1.6
Service category for this circuit: ubr Unspecified bit rate (best effort). ubrPcr Unspecified Bit Rate with Peak Cell Rate limit. nrtVbr Non-realtime Variable Bit Rate.
OBJECT-TYPE    
  INTEGER ubr(0), ubrPcr(1), nrtVbr(2)  

rsAtmSubIfVccPcr 1.3.6.1.4.1.2773.2.8.1.3.3.1.7
Peak Cell Rate, in cells per second, of this circuit. This parameter is only required when rsAtmSubIfVccServiceCategory is configured to have one of the following values: ubrPcr nrtVbr
OBJECT-TYPE    
  Integer32  

rsAtmSubIfVccScr 1.3.6.1.4.1.2773.2.8.1.3.3.1.8
Sustained Cell Rate, in cells per second, of this circuit. This parameter is only required when rsAtmSubIfVccServiceCategory is configured to have one of the following values: nrtVbr
OBJECT-TYPE    
  Integer32  

rsAtmSubIfVccMbs 1.3.6.1.4.1.2773.2.8.1.3.3.1.9
Maximum Burst Size, in cells, of this circuit. This parameter is only required when rsAtmSubIfVccServiceCategory is configured to have one of the following values: nrtVbr
OBJECT-TYPE    
  Integer32  

rsAtmConformance 1.3.6.1.4.1.2773.2.8.4
OBJECT IDENTIFIER    

rsAtmCompliances 1.3.6.1.4.1.2773.2.8.4.1
OBJECT IDENTIFIER    

rsAtmCompliance 1.3.6.1.4.1.2773.2.8.4.1.1
The compliance statement for entities which implement the Redstone ATM MIB.
MODULE-COMPLIANCE    

rsAtmGroups 1.3.6.1.4.1.2773.2.8.4.2
OBJECT IDENTIFIER    

rsAtmGroup 1.3.6.1.4.1.2773.2.8.4.2.1
A collection of objects providing management of ATM interfaces in a Redstone product.
OBJECT-GROUP    

rsAtmAal5Group 1.3.6.1.4.1.2773.2.8.4.2.2
A collection of objects providing management of AAL5 interfaces in a Redstone product.
OBJECT-GROUP    

rsAtmSubIfGroup 1.3.6.1.4.1.2773.2.8.4.2.3
A collection of objects providing management of ATM subinterfaces in a Redstone product.
OBJECT-GROUP    

Defined Objects

RsAtmIfEntry  
SEQUENCE    
  InterfaceIndex as rsAtmIfIndex  
  RowStatus as rsAtmIfRowStatus  
  InterfaceIndexOrZero as rsAtmIfLowerIfIndex  
  Integer32 as rsAtmIfIlmiVpi  
  Integer32 as rsAtmIfIlmiVci  
  Integer32 as rsAtmIfIlmiVcd  
  Integer32 as rsAtmIfIlmiPollFrequency  
  INTEGER as rsAtmIfIlmiAdminState  
  INTEGER as rsAtmIfUniVersion  

RsAtmAal5IfEntry  
SEQUENCE    
  InterfaceIndex as rsAtmAal5IfIndex  
  RowStatus as rsAtmAal5IfRowStatus  
  InterfaceIndexOrZero as rsAtmAal5IfLowerIfIndex  

RsAtmSubIfEntry  
SEQUENCE    
  InterfaceIndex as rsAtmSubIfIndex  
  RowStatus as rsAtmSubIfRowStatus  
  Integer32 as rsAtmSubIfDistinguisher  
  InterfaceIndexOrZero as rsAtmSubIfLowerIfIndex  

RsAtmSubIfVccEntry  
SEQUENCE    
  Integer32 as rsAtmSubIfVccVpi  
  Integer32 as rsAtmSubIfVccVci  
  RowStatus as rsAtmSubIfVccRowStatus  
  Integer32 as rsAtmSubIfVccVcd  
  INTEGER as rsAtmSubIfVccType  
  INTEGER as rsAtmSubIfVccServiceCategory  
  Integer32 as rsAtmSubIfVccPcr  
  Integer32 as rsAtmSubIfVccScr  
  Integer32 as rsAtmSubIfVccMbs