RFC1232-MIB

File: RFC1232-MIB.mib (36899 bytes)

Imported modules

RFC1155-SMI SNMPv2-TC RFC-1212

Imported symbols

experimental Counter DisplayString
OBJECT-TYPE

Defined Objects

ds1 1.3.6.1.3.2
OBJECT IDENTIFIER    

ds1ConfigTable 1.3.6.1.3.2.1
The DS1 Configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    DS1ConfigEntry

ds1ConfigEntry 1.3.6.1.3.2.1.1
An entry in the DS1 Configuration table.
OBJECT-TYPE    
  DS1ConfigEntry  

ds1CSUIndex 1.3.6.1.3.2.1.1.1
The index value which uniquely identifies the CSU to which this entry is applicable.
OBJECT-TYPE    
  INTEGER  

ds1Index 1.3.6.1.3.2.1.1.2
An index value that uniquely identifies an interface to a ds1. The interface identified by a particular value of this index is the same interface as identified by the same value an ifIndex object instance.
OBJECT-TYPE    
  INTEGER  

ds1TimeElapsed 1.3.6.1.3.2.1.1.3
The number of seconds that have elapsed since the beginning of the current error-measurement period. Any fraction is rounded up.
OBJECT-TYPE    
  INTEGER 1..900  

ds1ValidIntervals 1.3.6.1.3.2.1.1.4
The number of previous intervals for which valid data was collected. The value will be 96 unless the CSU device was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute intervals the CSU has been online.
OBJECT-TYPE    
  INTEGER 0..96  

ds1LineType 1.3.6.1.3.2.1.1.5
This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as well as the interpretation of the usage and error statistics. The values, in sequence, describe: TITLE: SPECIFICATION: ds1ESF AT&T Extended SuperFrame DS1 [10] ds1D4 AT&T D4 format DS1 [16], [17] ds1ANSI-ESF ANSI Extended SuperFrame format [14] ds1G704 CCITT Recommendation G.704 [12] (section 2.1.3.2) ds1G704-CRC CCITT Recommendation G.704 [12] (section 2.1.3.1)
OBJECT-TYPE    
  INTEGER other(1), ds1ESF(2), ds1D4(3), ds1ANSI-ESF(4), ds1G704(5), ds1G704-CRC(6)  

ds1ZeroCoding 1.3.6.1.3.2.1.1.6
This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. ds1JammedBit refers the Jammed bit Zero Encoding, in which the AT&T specification of at least one pulse every 8 bit periods is literally implemented by forcing a pulse in bit 8 of each channel. Thus, only seven bits per channel, or 1.344 Mbps, is available for data. ds1B8ZS refers to the use of a specified pattern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits (see [14]). In this context, all eight bits in a channel are technically available for data, but care must be taken with D4 encoded data to avoid having HDLC Flag streams imitate spurious Yellow Alarm conditions. Typically, one bit per frame is ignored to force flag streams to rotate, thereby avoiding this error type. CCITT Recommendation G.703 [11] may be referred to for further definition of these. ds1InvertedHDLC refers to the practice, common on HDLC encoded DS1 data links, of inverting the data between the serial interface chip and the CSU. Since HDLC guarantees one zero every 6 bits in the worst case, while the standards call for (in effect) at least one pulse every eight, inverted HDLC enjoys 4/24 one's density on the line, which may improve the effective clock stability of a DS1 line. As with B8ZS, all eight bits in a channel are technically available for data, but care must be taken with D4 encoded data to avoid having HDLC Flag streams imitate spurious Yellow Alarm conditions. Typically, one bit per frame is ignored to force flag streams to rotate, thereby avoiding this error type. ANSI Clear Channels may use ds1ZBTSI, or Zero Byte Time Slot Interchange (see [14]). G.704 links, with or without CRC, use ds1HDB3 (see [11]).
OBJECT-TYPE    
  INTEGER ds1JammedBit(1), ds1B8ZS(2), ds1InvertedHDLC(3), ds1HDB3(4), ds1ZBTSI(5)  

ds1Loopback 1.3.6.1.3.2.1.1.7
This variable represents the loopback state of the CSU. Devices supporting read/write access should return badValue in response to a requested loopback state that the CSU does not support. The values mean: ds1NoLoop Not in the loopback state. A device that is not capable of performing a loopback on either interface shall always return this as it's value. ds1LocalLoopbackLocalSide Signal received from the local side of the device is looped back at the local connector (eg, without involving the CSU). ds1LocalLoopbackRemoteSide Signal received from the local side of the device is looped back at the remote connector (eg, through the CSU). ds1RemoteLoopbackLocalSide Signal received from the remote side of the device is looped back at the local connector (eg, through the CSU). ds1RemoteLoopbackRemoteSide Signal received from the remote side of the device is looped back at the remote connector (eg, without involving the CSU).
OBJECT-TYPE    
  INTEGER ds1NoLoop(1), ds1LocalLoopbackLocalSide(2), ds1LocalLoopbackRemoteSide(3), ds1RemoteLoopbackLocalSide(4), ds1RemoteLoopbackRemoteSide(5)  

ds1SendCode 1.3.6.1.3.2.1.1.8
This variable indicates what type of code is being sent across the DS1 circuit by the CSU. The values mean: ds1SendNoCode sending looped or normal data ds1SendSetCode sending a loopback request ds1SendResetCode sending a loopback termination request ds1SendQRSS sending the BERT pattern described in ANSI T1.403-1989 section 5.6 ds1OtherTest sending a different BERT/BLERT pattern, such as all zeroes, all ones, etc.
OBJECT-TYPE    
  INTEGER ds1OtherTest(1), ds1SendNoCode(2), ds1SendSetCode(3), ds1SendResetCode(4), ds1SendQRSS(5)  

ds1YellowAlarm 1.3.6.1.3.2.1.1.9
This variable indicates if a Yellow Alarm condition exists. Note that G.704 interfaces do not support Yellow Alarms. Accordingly, such agents should return the value ds1NoYellowAlarm.
OBJECT-TYPE    
  INTEGER ds1NoYellowAlarm(1), ds1YellowAlarm(2)  

ds1RedAlarm 1.3.6.1.3.2.1.1.10
This variable indicates if a Red Alarm condition exists. Note that G.704 interfaces do not support Red Alarms. Accordingly, such agents should return the value ds1NoRedAlarm.
OBJECT-TYPE    
  INTEGER ds1NoRedAlarm(1), ds1RedAlarm(2)  

ds1CircuitIdentifier 1.3.6.1.3.2.1.1.11
This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

ds1IntervalTable 1.3.6.1.3.2.2
The DS1 Interval table.
OBJECT-TYPE    
  SEQUENCE OF  
    DS1IntervalEntry

ds1IntervalEntry 1.3.6.1.3.2.2.1
An entry in the DS1 Interval table.
OBJECT-TYPE    
  DS1IntervalEntry  

ds1IntervalIndex 1.3.6.1.3.2.2.1.1
The index value which uniquely identifies the CSU to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value an ds1CSUIndex object instance.
OBJECT-TYPE    
  INTEGER  

ds1IntervalNumber 1.3.6.1.3.2.2.1.2
A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minute interval (assuming that all 96 intervals are valid).
OBJECT-TYPE    
  INTEGER 1..96  

ds1IntervalESs 1.3.6.1.3.2.2.1.3
The counter associated with the number of Errored Seconds, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU during one of the previous 96 fifteen minute intervals.
OBJECT-TYPE    
  Counter  

ds1IntervalSESs 1.3.6.1.3.2.2.1.4
The counter associated with the number of Severely Errored Seconds, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU during one of the previous 96 fifteen minute intervals.
OBJECT-TYPE    
  Counter  

ds1IntervalSEFSs 1.3.6.1.3.2.2.1.5
The counter associated with the number of Severely Errored Framing Seconds, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU during one of the previous 96 fifteen minute intervals.
OBJECT-TYPE    
  Counter  

ds1IntervalUASs 1.3.6.1.3.2.2.1.6
The counter associated with the number of Unavailable Seconds, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU during one of the previous 96 fifteen minute intervals.
OBJECT-TYPE    
  Counter  

ds1IntervalCSSs 1.3.6.1.3.2.2.1.7
The counter associated with the number of Controlled Slip Seconds, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU during one of the previous 96 fifteen minute intervals.
OBJECT-TYPE    
  Counter  

ds1IntervalBPVs 1.3.6.1.3.2.2.1.8
The counter associated with the number of Bipolar Violations, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU during one of the previous 96 fifteen minute intervals.
OBJECT-TYPE    
  Counter  

ds1IntervalCVs 1.3.6.1.3.2.2.1.9
The counter associated with the number of Code Violation Error Events, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU during one of the previous 96 fifteen minute intervals. Note that D4 and G.704 (section 2.1.3.2) interfaces do not support Code Violation Error Events. Accordingly, such agents may treat this object as having an ACCESS clause value of not- accessible.
OBJECT-TYPE    
  Counter  

ds1CurrentTable 1.3.6.1.3.2.3
The DS1 Current table.
OBJECT-TYPE    
  SEQUENCE OF  
    DS1CurrentEntry

ds1CurrentEntry 1.3.6.1.3.2.3.1
An entry in the DS1 Current table.
OBJECT-TYPE    
  DS1CurrentEntry  

ds1CurrentIndex 1.3.6.1.3.2.3.1.1
The index value which uniquely identifies the CSU to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value an ds1CSUIndex object instance.
OBJECT-TYPE    
  INTEGER  

ds1CurrentESs 1.3.6.1.3.2.3.1.2
The counter associated with the number of Errored Seconds, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU in the current 15 minute interval.
OBJECT-TYPE    
  Counter  

ds1CurrentSESs 1.3.6.1.3.2.3.1.3
The counter associated with the number of Severely Errored Seconds, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU in the current 15 minute interval.
OBJECT-TYPE    
  Counter  

ds1CurrentSEFSs 1.3.6.1.3.2.3.1.4
The counter associated with the number of Severely Errored Framing Seconds, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU in the current 15 minute interval.
OBJECT-TYPE    
  Counter  

ds1CurrentUASs 1.3.6.1.3.2.3.1.5
The counter associated with the number of Unavailable Seconds, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU in the current 15 minute interval.
OBJECT-TYPE    
  Counter  

ds1CurrentCSSs 1.3.6.1.3.2.3.1.6
The counter associated with the number of Controlled Slip Seconds, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU in the current 15 minute interval.
OBJECT-TYPE    
  Counter  

ds1CurrentBPVs 1.3.6.1.3.2.3.1.7
The counter associated with the number of Bipolar Violations, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU in the current 15 minute interval.
OBJECT-TYPE    
  Counter  

ds1CurrentCVs 1.3.6.1.3.2.3.1.8
The counter associated with the number of Code Violation Error Events, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU in the current 15 minute interval. Note that D4 and G.704 (section 2.1.3.2) interfaces do not support Code Violation Error Events. Accordingly, such agents may treat this object as having an ACCESS clause value of not- accessible.
OBJECT-TYPE    
  Counter  

ds1TotalTable 1.3.6.1.3.2.4
The DS1 Total table. 24 hour interval.
OBJECT-TYPE    
  SEQUENCE OF  
    DS1TotalEntry

ds1TotalEntry 1.3.6.1.3.2.4.1
An entry in the DS1 Total table.
OBJECT-TYPE    
  DS1TotalEntry  

ds1TotalIndex 1.3.6.1.3.2.4.1.1
The index value which uniquely identifies the CSU to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value an ds1CSUIndex object instance.
OBJECT-TYPE    
  INTEGER  

ds1TotalESs 1.3.6.1.3.2.4.1.2
The counter associated with the number of Errored Seconds, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU in the previous 24 hour interval
OBJECT-TYPE    
  Counter  

ds1TotalSESs 1.3.6.1.3.2.4.1.3
The counter associated with the number of Severely Errored Seconds, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU in the previous 24 hour interval.
OBJECT-TYPE    
  Counter  

ds1TotalSEFSs 1.3.6.1.3.2.4.1.4
The counter associated with the number of Severely Errored Framing Seconds, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU in the previous 24 hour interval.
OBJECT-TYPE    
  Counter  

ds1TotalUASs 1.3.6.1.3.2.4.1.5
The counter associated with the number of Unavailable Seconds, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU in the previous 24 hour interval.
OBJECT-TYPE    
  Counter  

ds1TotalCSSs 1.3.6.1.3.2.4.1.6
The counter associated with the number of Controlled Slip Seconds, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU in the previous 24 hour interval.
OBJECT-TYPE    
  Counter  

ds1TotalBPVs 1.3.6.1.3.2.4.1.7
The counter associated with the number of Bipolar Violations, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU in the previous 24 hour interval.
OBJECT-TYPE    
  Counter  

ds1TotalCVs 1.3.6.1.3.2.4.1.8
The counter associated with the number of Code Violation Error Events, as defined by ANSI Draft Standard T1M1.3/90 - 027R2[15], encountered by a DS1 CSU in the previous 24 hour interval. Note that D4 and G.704 (section 2.1.3.2) interfaces do not support Code Violation Error Events. Accordingly, such agents may treat this object as having an ACCESS clause value of not- accessible.
OBJECT-TYPE    
  Counter  

ds1FracTable 1.3.6.1.3.2.5
The DS1 Fractional table.
OBJECT-TYPE    
  SEQUENCE OF  
    DS1FracEntry

ds1FracEntry 1.3.6.1.3.2.5.1
An entry in the DS1 Fractional table.
OBJECT-TYPE    
  DS1FracEntry  

ds1FracIndex 1.3.6.1.3.2.5.1.1
The index value which uniquely identifies the CSU to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value an ds1CSUIndex object instance.
OBJECT-TYPE    
  INTEGER  

ds1FracNumber 1.3.6.1.3.2.5.1.2
The channel number for this entry.
OBJECT-TYPE    
  INTEGER 1..32  

ds1FracIfIndex 1.3.6.1.3.2.5.1.3
An index value that uniquely identifies an interface to a ds1. The interface identified by a particular value of this index is the same interface as identified by the same value an ifIndex object instance.
OBJECT-TYPE    
  INTEGER  

Defined Objects

DS1ConfigEntry  
SEQUENCE    
  INTEGER as ds1CSUIndex  
  INTEGER as ds1Index  
  INTEGER as ds1TimeElapsed 1..900  
  INTEGER as ds1ValidIntervals 0..96  
  INTEGER as ds1LineType  
  INTEGER as ds1ZeroCoding  
  INTEGER as ds1Loopback  
  INTEGER as ds1SendCode  
  INTEGER as ds1YellowAlarm  
  INTEGER as ds1RedAlarm  
  DisplayString as ds1CircuitIdentifier SIZE(0..255)  

DS1IntervalEntry  
SEQUENCE    
  INTEGER as ds1IntervalIndex  
  INTEGER as ds1IntervalNumber 1..96  
  Counter as ds1IntervalESs  
  Counter as ds1IntervalSESs  
  Counter as ds1IntervalSEFSs  
  Counter as ds1IntervalUASs  
  Counter as ds1IntervalCSSs  
  Counter as ds1IntervalBPVs  
  Counter as ds1IntervalCVs  

DS1CurrentEntry  
SEQUENCE    
  INTEGER as ds1CurrentIndex  
  Counter as ds1CurrentESs  
  Counter as ds1CurrentSESs  
  Counter as ds1CurrentSEFSs  
  Counter as ds1CurrentUASs  
  Counter as ds1CurrentCSSs  
  Counter as ds1CurrentBPVs  
  Counter as ds1CurrentCVs  

DS1TotalEntry  
SEQUENCE    
  INTEGER as ds1TotalIndex  
  Counter as ds1TotalESs  
  Counter as ds1TotalSESs  
  Counter as ds1TotalSEFSs  
  Counter as ds1TotalUASs  
  Counter as ds1TotalCSSs  
  Counter as ds1TotalBPVs  
  Counter as ds1TotalCVs  

DS1FracEntry  
SEQUENCE    
  INTEGER as ds1FracIndex  
  INTEGER as ds1FracNumber 1..32  
  INTEGER as ds1FracIfIndex