RFC1381-MIB

File: RFC1381-MIB.mib (44055 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
RFC1253-MIB

Imported symbols

Counter transmission OBJECT-TYPE
PositiveInteger

Defined Objects

lapb 1.3.6.1.2.1.10.16
OBJECT IDENTIFIER    

lapbAdmnTable 1.3.6.1.2.1.10.16.1
This table contains objects that can be changed to manage a LAPB interface. Changing one of these parameters may take effect in the operating LAPB immediately or may wait until the interface is restarted depending on the details of the implementation. Most of the objects in this read-write table have corresponding read-only objects in the lapbOperTable that return the current operating value. The operating values may be different from these configured values if changed by XID negotiation or if a configured parameter was changed after the interface was started.
OBJECT-TYPE    
  SEQUENCE OF  
    LapbAdmnEntry

lapbAdmnEntry 1.3.6.1.2.1.10.16.1.1
Configured parameter values for a specific LAPB.
OBJECT-TYPE    
  LapbAdmnEntry  

lapbAdmnIndex 1.3.6.1.2.1.10.16.1.1.1
The ifIndex value for the LAPB interface.
OBJECT-TYPE    
  IfIndexType  

lapbAdmnStationType 1.3.6.1.2.1.10.16.1.1.2
Identifies the desired station type of this interface.
OBJECT-TYPE    
  INTEGER dte(1), dce(2), dxe(3)  

lapbAdmnControlField 1.3.6.1.2.1.10.16.1.1.3
The desired size of the sequence numbers used to number frames.
OBJECT-TYPE    
  INTEGER modulo8(1), modulo128(2)  

lapbAdmnTransmitN1FrameSize 1.3.6.1.2.1.10.16.1.1.4
The default maximum N1 frame size desired in number of bits for a frame transmitted by this DTE. This excludes flags and 0 bits inserted for transparency.
OBJECT-TYPE    
  PositiveInteger  

lapbAdmnReceiveN1FrameSize 1.3.6.1.2.1.10.16.1.1.5
The default maximum N1 frame size desired in number of bits for a frame the DCE/remote DTE transmits to this DTE. This excludes flags and 0 bits inserted for transparency.
OBJECT-TYPE    
  PositiveInteger  

lapbAdmnTransmitKWindowSize 1.3.6.1.2.1.10.16.1.1.6
The default transmit window size for this Interface. This is the maximum number of unacknowledged sequenced PDUs that may be outstanding from this DTE at any one time.
OBJECT-TYPE    
  INTEGER 1..127  

lapbAdmnReceiveKWindowSize 1.3.6.1.2.1.10.16.1.1.7
The default receive window size for this Interface. This is the maximum number of unacknowledged sequenced PDUs that may be outstanding from the DCE/remote DTE at any one time.
OBJECT-TYPE    
  INTEGER 1..127  

lapbAdmnN2RxmitCount 1.3.6.1.2.1.10.16.1.1.8
The default N2 retry counter for this interface. This specifies the number of times a PDU will be resent after the T1 timer expires without an acknowledgement for the PDU.
OBJECT-TYPE    
  INTEGER 0..65535  

lapbAdmnT1AckTimer 1.3.6.1.2.1.10.16.1.1.9
The default T1 timer for this interface. This specifies the maximum time in Milliseconds to wait for acknowledgment of a PDU.
OBJECT-TYPE    
  PositiveInteger  

lapbAdmnT2AckDelayTimer 1.3.6.1.2.1.10.16.1.1.10
The default T2 timer for this interface. This specifies the maximum time in Milliseconds to wait before sending an acknowledgment for a sequenced PDU. A value of zero means there will be no delay in acknowledgement generation.
OBJECT-TYPE    
  PositiveInteger  

lapbAdmnT3DisconnectTimer 1.3.6.1.2.1.10.16.1.1.11
The T3 timer for this interface. This specifies the time in Milliseconds to wait before considering the link disconnected. A value of zero indicates the link will be considered disconnected upon completion of the frame exchange to disconnect the link.
OBJECT-TYPE    
  PositiveInteger  

lapbAdmnT4IdleTimer 1.3.6.1.2.1.10.16.1.1.12
The T4 timer for this interface. This specifies the maximum time in Milliseconds to allow without frames being exchanged on the data link. A value of 2147483647 indicates no idle timer is being kept.
OBJECT-TYPE    
  PositiveInteger  

lapbAdmnActionInitiate 1.3.6.1.2.1.10.16.1.1.13
This identifies the action LAPB will take to initiate link set-up.
OBJECT-TYPE    
  INTEGER sendSABM(1), sendDISC(2), sendDM(3), none(4), other(5)  

lapbAdmnActionRecvDM 1.3.6.1.2.1.10.16.1.1.14
This identifies the action LAPB will take when it receives a DM response.
OBJECT-TYPE    
  INTEGER sendSABM(1), sendDISC(2), other(3)  

lapbOperTable 1.3.6.1.2.1.10.16.2
This table contains configuration information about interface parameters currently set in the interface. Many of these objects have corresponding objects in the lapbAdmnTable.
OBJECT-TYPE    
  SEQUENCE OF  
    LapbOperEntry

lapbOperEntry 1.3.6.1.2.1.10.16.2.1
Currently set parameter values for a specific LAPB.
OBJECT-TYPE    
  LapbOperEntry  

lapbOperIndex 1.3.6.1.2.1.10.16.2.1.1
The ifIndex value for the LAPB interface.
OBJECT-TYPE    
  IfIndexType  

lapbOperStationType 1.3.6.1.2.1.10.16.2.1.2
Identifies the current operating station type of this interface. A value of dxe (3) indicates XID negotiation has not yet taken place.
OBJECT-TYPE    
  INTEGER dte(1), dce(2), dxe(3)  

lapbOperControlField 1.3.6.1.2.1.10.16.2.1.3
The current operating size of the sequence numbers used to number frames.
OBJECT-TYPE    
  INTEGER modulo8(1), modulo128(2)  

lapbOperTransmitN1FrameSize 1.3.6.1.2.1.10.16.2.1.4
The current operating N1 frame size used for the maximum number of bits in a frame this DTE can transmit. This excludes flags and 0 bits inserted for transparency.
OBJECT-TYPE    
  PositiveInteger  

lapbOperReceiveN1FrameSize 1.3.6.1.2.1.10.16.2.1.5
The current operating N1 frame size used for the maximum number of bits in a frame the DCE/remote DTE can transmit. This excludes flags and 0 bits inserted for transparency.
OBJECT-TYPE    
  PositiveInteger  

lapbOperTransmitKWindowSize 1.3.6.1.2.1.10.16.2.1.6
The current PDU window size this Interface uses to transmit. This is the maximum number of unacknowledged sequenced PDUs that may be outstanding from this DTE at any one time.
OBJECT-TYPE    
  INTEGER 1..127  

lapbOperReceiveKWindowSize 1.3.6.1.2.1.10.16.2.1.7
The current receive PDU window size for this Interface. This is the maximum number of unacknowledged sequenced PDUs that may be outstanding from the DCE/remote DTE at any one time.
OBJECT-TYPE    
  INTEGER 1..127  

lapbOperN2RxmitCount 1.3.6.1.2.1.10.16.2.1.8
The current N2 retry counter used for this interface. This specifies the number of times a PDU will be resent after the T1 timer expires without an acknowledgement for the PDU.
OBJECT-TYPE    
  INTEGER 0..65535  

lapbOperT1AckTimer 1.3.6.1.2.1.10.16.2.1.9
The current T1 timer for this interface. This specifies the maximum time in Milliseconds to wait for acknowledgment of a PDU.
OBJECT-TYPE    
  PositiveInteger  

lapbOperT2AckDelayTimer 1.3.6.1.2.1.10.16.2.1.10
The current T2 timer for this interface. This specifies the maximum time in Milliseconds to wait before sending an acknowledgment for a sequenced PDU. A value of zero means there will be no delay in acknowledgement generation.
OBJECT-TYPE    
  PositiveInteger  

lapbOperT3DisconnectTimer 1.3.6.1.2.1.10.16.2.1.11
The current T3 timer for this interface. This specifies the time in Milliseconds to wait before considering the link disconnected. A value of zero indicates the link will be considered disconnected upon completion of the frame exchange to disconnect the link.
OBJECT-TYPE    
  PositiveInteger  

lapbOperT4IdleTimer 1.3.6.1.2.1.10.16.2.1.12
The current T4 timer for this interface. This specifies the maximum time in Milliseconds to allow without frames being exchanged on the data link. A value of 2147483647 indicates no idle timer is being kept.
OBJECT-TYPE    
  PositiveInteger  

lapbOperPortId 1.3.6.1.2.1.10.16.2.1.13
This object identifies an instance of the index object in the first group of objects in the MIB specific to the physical device or interface used to send and receive frames. If an agent does not support any such objects, it should return nullSpec OBJECT IDENTIFIER {0 0}.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

lapbOperProtocolVersionId 1.3.6.1.2.1.10.16.2.1.14
This object identifies the version of the lapb protocol implemented by this interface.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

lapbFlowTable 1.3.6.1.2.1.10.16.3
This table defines the objects recorded by LAPB to provide information about the traffic flow through the interface.
OBJECT-TYPE    
  SEQUENCE OF  
    LapbFlowEntry

lapbFlowEntry 1.3.6.1.2.1.10.16.3.1
The information regarding the effects of flow controls in LAPB.
OBJECT-TYPE    
  LapbFlowEntry  

lapbFlowIfIndex 1.3.6.1.2.1.10.16.3.1.1
The ifIndex value for the LAPB Interface.
OBJECT-TYPE    
  IfIndexType  

lapbFlowStateChanges 1.3.6.1.2.1.10.16.3.1.2
The number of LAPB State Changes, including resets.
OBJECT-TYPE    
  Counter  

lapbFlowChangeReason 1.3.6.1.2.1.10.16.3.1.3
The reason for the most recent incrementing of lapbFlowStateChanges. A DM or DISC frame generated to initiate link set-up does not alter this object. When the MIB-II object ifOperStatus does not have a value of testing, there exists a correlation between this object and ifOperStatus. IfOperStatus will have a value of up when this object contains: abmEntered, abmeEntered, abmReset, or abmeReset. IfOperStatus will have a value of down when this object has a value of notStarted, or dmReceived through n2Timeout. There is no correlation when this object has the value other.
OBJECT-TYPE    
  INTEGER notStarted(1), abmEntered(2), abmeEntered(3), abmReset(4), abmeReset(5), dmReceived(6), dmSent(7), discReceived(8), discSent(9), frmrReceived(10), frmrSent(11), n2Timeout(12), other(13)  

lapbFlowCurrentMode 1.3.6.1.2.1.10.16.3.1.4
The current condition of the conversation.
OBJECT-TYPE    
  INTEGER disconnected(1), linkSetup(2), frameReject(3), disconnectRequest(4), informationTransfer(5), rejFrameSent(6), waitingAcknowledgement(7), stationBusy(8), remoteStationBusy(9), bothStationsBusy(10), waitingAckStationBusy(11), waitingAckRemoteBusy(12), waitingAckBothBusy(13), rejFrameSentRemoteBusy(14), xidFrameSent(15), error(16), other(17)  

lapbFlowBusyDefers 1.3.6.1.2.1.10.16.3.1.5
The number of times this device was unable to transmit a frame due to a perceived remote busy condition. Busy conditions can result from the receipt of an RNR from the remote device, the lack of valid sequence number space (window saturation), or other conditions.
OBJECT-TYPE    
  Counter  

lapbFlowRejOutPkts 1.3.6.1.2.1.10.16.3.1.6
The number of REJ or SREJ frames sent by this station.
OBJECT-TYPE    
  Counter  

lapbFlowRejInPkts 1.3.6.1.2.1.10.16.3.1.7
The number of REJ or SREJ frames received by this station.
OBJECT-TYPE    
  Counter  

lapbFlowT1Timeouts 1.3.6.1.2.1.10.16.3.1.8
The number of times a re-transmission was effected by the T1 Timer expiring.
OBJECT-TYPE    
  Counter  

lapbFlowFrmrSent 1.3.6.1.2.1.10.16.3.1.9
The Information Field of the FRMR most recently sent. If no FRMR has been sent (the normal case) or the information isn't available, this will be an OCTET STRING of zero length.
OBJECT-TYPE    
  OCTET STRING SIZE(0..7)  

lapbFlowFrmrReceived 1.3.6.1.2.1.10.16.3.1.10
The Information Field of the FRMR most recently received. If no FRMR has been received (the normal case) or the information isn't available, this will be an OCTET STRING of zero length.
OBJECT-TYPE    
  OCTET STRING SIZE(0..7)  

lapbFlowXidReceived 1.3.6.1.2.1.10.16.3.1.11
The Information Field of the XID frame most recently received. If no XID frame has been received, this will be an OCTET STRING of zero length.
OBJECT-TYPE    
  OCTET STRING SIZE(0..8206)  

lapbXidTable 1.3.6.1.2.1.10.16.4
This table defines values to use for XID negotiation that are not found in the lapbAdmnTable. This table is optional for implementations that don't support XID and mandatory for implementations that do initiate XID negotiation.
OBJECT-TYPE    
  SEQUENCE OF  
    LapbXidEntry

lapbXidEntry 1.3.6.1.2.1.10.16.4.1
XId negotiation parameter values for a specific LAPB.
OBJECT-TYPE    
  LapbXidEntry  

lapbXidIndex 1.3.6.1.2.1.10.16.4.1.1
The ifIndex value for the LAPB interface.
OBJECT-TYPE    
  IfIndexType  

lapbXidAdRIdentifier 1.3.6.1.2.1.10.16.4.1.2
The value of the Address Resolution Identifier. A zero length string indicates no Identifier value has been assigned.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

lapbXidAdRAddress 1.3.6.1.2.1.10.16.4.1.3
The value of the Address Resolution Address. A zero length string indicates no Address value has been assigned.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

lapbXidParameterUniqueIdentifier 1.3.6.1.2.1.10.16.4.1.4
The value of the parameter unique Identifier. A zero length string indicates no Unique identifier value has been assigned.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

lapbXidGroupAddress 1.3.6.1.2.1.10.16.4.1.5
The value of the parameter Group address. A zero length string indicates no Group address value has been assigned.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

lapbXidPortNumber 1.3.6.1.2.1.10.16.4.1.6
The port number assigned for this link. A zero length string indicates no local port number identifier has been assigned.
OBJECT-TYPE    
  OCTET STRING SIZE(0..255)  

lapbXidUserDataSubfield 1.3.6.1.2.1.10.16.4.1.7
A user data subfield, if any, to be transmitted in an XID frame. A zero length frame indicates no user data subfield has been assigned. The octet string should include both the User data identifier and User data field as shown in Figures 1 and 4.
OBJECT-TYPE    
  OCTET STRING SIZE(0..8206)  

lapbProtocolVersion 1.3.6.1.2.1.10.16.5
OBJECT IDENTIFIER    

lapbProtocolIso7776v1986 1.3.6.1.2.1.10.16.5.1
OBJECT IDENTIFIER    

lapbProtocolCcittV1980 1.3.6.1.2.1.10.16.5.2
OBJECT IDENTIFIER    

lapbProtocolCcittV1984 1.3.6.1.2.1.10.16.5.3
OBJECT IDENTIFIER    

Defined Objects

IfIndexType  
INTEGER 1..2147483647    

LapbAdmnEntry  
SEQUENCE    
  IfIndexType as lapbAdmnIndex  
  INTEGER as lapbAdmnStationType  
  INTEGER as lapbAdmnControlField  
  PositiveInteger as lapbAdmnTransmitN1FrameSize  
  PositiveInteger as lapbAdmnReceiveN1FrameSize  
  INTEGER as lapbAdmnTransmitKWindowSize  
  INTEGER as lapbAdmnReceiveKWindowSize  
  INTEGER as lapbAdmnN2RxmitCount  
  PositiveInteger as lapbAdmnT1AckTimer  
  PositiveInteger as lapbAdmnT2AckDelayTimer  
  PositiveInteger as lapbAdmnT3DisconnectTimer  
  PositiveInteger as lapbAdmnT4IdleTimer  
  INTEGER as lapbAdmnActionInitiate  
  INTEGER as lapbAdmnActionRecvDM  

LapbOperEntry  
SEQUENCE    
  IfIndexType as lapbOperIndex  
  INTEGER as lapbOperStationType  
  INTEGER as lapbOperControlField  
  PositiveInteger as lapbOperTransmitN1FrameSize  
  PositiveInteger as lapbOperReceiveN1FrameSize  
  INTEGER as lapbOperTransmitKWindowSize  
  INTEGER as lapbOperReceiveKWindowSize  
  INTEGER as lapbOperN2RxmitCount  
  PositiveInteger as lapbOperT1AckTimer  
  PositiveInteger as lapbOperT2AckDelayTimer  
  PositiveInteger as lapbOperT3DisconnectTimer  
  PositiveInteger as lapbOperT4IdleTimer  
  OBJECT IDENTIFIER as lapbOperPortId  
  OBJECT IDENTIFIER as lapbOperProtocolVersionId  

LapbFlowEntry  
SEQUENCE    
  IfIndexType as lapbFlowIfIndex  
  Counter as lapbFlowStateChanges  
  INTEGER as lapbFlowChangeReason  
  INTEGER as lapbFlowCurrentMode  
  Counter as lapbFlowBusyDefers  
  Counter as lapbFlowRejOutPkts  
  Counter as lapbFlowRejInPkts  
  Counter as lapbFlowT1Timeouts  
  OCTET STRING as lapbFlowFrmrSent  
  OCTET STRING as lapbFlowFrmrReceived  
  OCTET STRING as lapbFlowXidReceived  

LapbXidEntry  
SEQUENCE    
  IfIndexType as lapbXidIndex  
  OCTET STRING as lapbXidAdRIdentifier  
  OCTET STRING as lapbXidAdRAddress  
  OCTET STRING as lapbXidParameterUniqueIdentifier  
  OCTET STRING as lapbXidGroupAddress  
  OCTET STRING as lapbXidPortNumber  
  OCTET STRING as lapbXidUserDataSubfield