
| RFC1155-SMI | RFC1213-MIB | RFC-1212 |
| Gauge | DisplayString | transmission |
| OBJECT-TYPE |
| ds3 | 1.3.6.1.2.1.10.30 | ||
| OBJECT IDENTIFIER | |||
| dsx3ConfigTable | 1.3.6.1.2.1.10.30.5 | ||
| The DS3/E3 Configuration table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| Dsx3ConfigEntry | |||
| dsx3ConfigEntry | 1.3.6.1.2.1.10.30.5.1 | ||
| An entry in the DS3/E3 Configuration table. | |||
| OBJECT-TYPE | |||
| Dsx3ConfigEntry | |||
| dsx3LineIndex | 1.3.6.1.2.1.10.30.5.1.1 | ||
| This object is the identifier of a DS3/E3 Interface on a managed device. If there is an ifEntry that is directly associated with this and only this DS3/E3 interface, it should have the same value as ifIndex. Otherwise, number the dsx3LineIndices with an unique identifier following the rules of choosing a number that is greater than ifNumber and numbering the inside interfaces (e.g., equipment side) with even numbers and outside interfaces (e.g, network side) with odd numbers. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| dsx3IfIndex | 1.3.6.1.2.1.10.30.5.1.2 | ||
| This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213). | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| dsx3TimeElapsed | 1.3.6.1.2.1.10.30.5.1.3 | ||
| The number of seconds that have elapsed since the beginning of the near end current error- measurement period. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..899 | ||
| dsx3ValidIntervals | 1.3.6.1.2.1.10.30.5.1.4 | ||
| The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute near end intervals since the interface has been online. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..96 | ||
| dsx3LineType | 1.3.6.1.2.1.10.30.5.1.5 | ||
| This variable indicates the variety of DS3 C-bit or E3 application implementing this interface. The type of interface affects the interpretation of the usage and error statistics. The rate of DS3 is 44.736 Mbps and E3 is 34.368 Mbps. The dsx3ClearChannel value means that the C-bits are not used except for sending/receiving AIS. The values, in sequence, describe: TITLE: SPECIFICATION: dsx3M23 ANSI T1.107-1988 dsx3SYNTRAN ANSI T1.107-1988 dsx3CbitParity ANSI T1.107a-1989 dsx3ClearChannel ANSI T1.102-1987 e3Framed CCITT G.751 e3Plcp ETSI T/NA(91)18. | |||
| OBJECT-TYPE | |||
| INTEGER | dsx3other(1), dsx3M23(2), dsx3SYNTRAN(3), dsx3CbitParity(4), dsx3ClearChannel(5), e3other(6), e3Framed(7), e3Plcp(8) | ||
| dsx3LineCoding | 1.3.6.1.2.1.10.30.5.1.6 | ||
| This variable describes the variety of Zero Code Suppression used on this interface, which in turn affects a number of its characteristics. dsx3B3ZS and e3HDB3 refer to the use of specified patterns of normal bits and bipolar violations which are used to replace sequences of zero bits of a specified length. | |||
| OBJECT-TYPE | |||
| INTEGER | dsx3Other(1), dsx3B3ZS(2), e3HDB3(3) | ||
| dsx3SendCode | 1.3.6.1.2.1.10.30.5.1.7 | ||
| This variable indicates what type of code is being sent across the DS3/E3 interface by the device. (These are optional for E3 interfaces.) The values mean: dsx3SendNoCode sending looped or normal data dsx3SendLineCode sending a request for a line loopback dsx3SendPayloadCode sending a request for a payload loopback (i.e., all DS1/E1s in a DS3/E3 frame) dsx3SendResetCode sending a loopback deactivation request dsx3SendDS1LoopCode requesting to loopback a particular DS1/E1 within a DS3/E3 frame dsx3SendTestPattern sending a test pattern. | |||
| OBJECT-TYPE | |||
| INTEGER | dsx3SendNoCode(1), dsx3SendLineCode(2), dsx3SendPayloadCode(3), dsx3SendResetCode(4), dsx3SendDS1LoopCode(5), dsx3SendTestPattern(6) | ||
| dsx3CircuitIdentifier | 1.3.6.1.2.1.10.30.5.1.8 | ||
| This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| dsx3LoopbackConfig | 1.3.6.1.2.1.10.30.5.1.9 | ||
| This variable represents the loopback configuration of the DS3/E3 interface. The values mean: dsx3NoLoop Not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as it's value. dsx3PayloadLoop The received signal at this interface is looped through the device. Typically the received signal is looped back for retransmission after it has passed through the device's framing function. dsx3LineLoop The received signal at this interface does not go through the device (minimum penetration) but is looped back out. dsx3OtherLoop Loopbacks that are not defined here. | |||
| OBJECT-TYPE | |||
| INTEGER | dsx3NoLoop(1), dsx3PayloadLoop(2), dsx3LineLoop(3), dsx3OtherLoop(4) | ||
| dsx3LineStatus | 1.3.6.1.2.1.10.30.5.1.10 | ||
| This variable indicates the Line Status of the interface. It contains loopback state information and failure state information. The dsx3LineStatus is a bit map represented as a sum, therefore, it can represent multiple failures and a loopback (see dsx3LoopbackConfig object for the type of loopback) simultaneously. The dsx3NoAlarm should be set if and only if no other flag is set. The various bit positions are: 1 dsx3NoAlarm No alarm present 2 dsx3RcvRAIFailure Receiving Yellow/Remote Alarm Indication 4 dsx3XmitRAIAlarm Transmitting Yellow/Remote Alarm Indication 8 dsx3RcvAIS Receiving AIS failure state 16 dsx3XmitAIS Transmitting AIS 32 dsx3LOF Receiving LOF failure state 64 dsx3LOS Receiving LOS failure state 128 dsx3LoopbackState Looping the received signal 256 dsx3RcvTestCode Receiving a Test Pattern 512 dsx3OtherFailure any line status not defined here | |||
| OBJECT-TYPE | |||
| INTEGER | 1..1023 | ||
| dsx3TransmitClockSource | 1.3.6.1.2.1.10.30.5.1.11 | ||
| The source of Transmit Clock. is derived from the recovered receive clock of another DS3 interface. | |||
| OBJECT-TYPE | |||
| INTEGER | loopTiming(1), localTiming(2), throughTiming(3) | ||
| dsx3CurrentTable | 1.3.6.1.2.1.10.30.6 | ||
| The DS3/E3 Current table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| Dsx3CurrentEntry | |||
| dsx3CurrentEntry | 1.3.6.1.2.1.10.30.6.1 | ||
| An entry in the DS3/E3 Current table. | |||
| OBJECT-TYPE | |||
| Dsx3CurrentEntry | |||
| dsx3CurrentIndex | 1.3.6.1.2.1.10.30.6.1.1 | ||
| The index value which uniquely identifies the DS3/E3 interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value an dsx3LineIndex object instance. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| dsx3CurrentPESs | 1.3.6.1.2.1.10.30.6.1.2 | ||
| The counter associated with the number of P-bit Errored Seconds, encountered by a DS3 interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3CurrentPSESs | 1.3.6.1.2.1.10.30.6.1.3 | ||
| The counter associated with the number of P-bit Severely Errored Seconds, encountered by a DS3 interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3CurrentSEFSs | 1.3.6.1.2.1.10.30.6.1.4 | ||
| The counter associated with the number of Severely Errored Framing Seconds, encountered by a DS3/E3 interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3CurrentUASs | 1.3.6.1.2.1.10.30.6.1.5 | ||
| The counter associated with the number of Unavailable Seconds, encountered by a DS3 interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3CurrentLCVs | 1.3.6.1.2.1.10.30.6.1.6 | ||
| The counter associated with the number of Line Coding Violations encountered by a DS3/E3 interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3CurrentPCVs | 1.3.6.1.2.1.10.30.6.1.7 | ||
| The counter associated with the number of P-bit Coding Violations, encountered by a DS3 interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3CurrentLESs | 1.3.6.1.2.1.10.30.6.1.8 | ||
| The number of Line Errored Seconds encountered by a DS3/E3 interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3CurrentCCVs | 1.3.6.1.2.1.10.30.6.1.9 | ||
| The number of C-bit Coding Violations encountered by a DS3 interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3CurrentCESs | 1.3.6.1.2.1.10.30.6.1.10 | ||
| The number of C-bit Errored Seconds encountered by a DS3 interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3CurrentCSESs | 1.3.6.1.2.1.10.30.6.1.11 | ||
| The number of C-bit Severely Errored Seconds encountered by a DS3 interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3IntervalTable | 1.3.6.1.2.1.10.30.7 | ||
| The DS3/E3 Interval table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| Dsx3IntervalEntry | |||
| dsx3IntervalEntry | 1.3.6.1.2.1.10.30.7.1 | ||
| An entry in the DS3/E3 Interval table. | |||
| OBJECT-TYPE | |||
| Dsx3IntervalEntry | |||
| dsx3IntervalIndex | 1.3.6.1.2.1.10.30.7.1.1 | ||
| The index value which uniquely identifies the DS3/E3 interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value an dsx3LineIndex object instance. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| dsx3IntervalNumber | 1.3.6.1.2.1.10.30.7.1.2 | ||
| A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid). | |||
| OBJECT-TYPE | |||
| INTEGER | 1..96 | ||
| dsx3IntervalPESs | 1.3.6.1.2.1.10.30.7.1.3 | ||
| The counter associated with the number of P-bit Errored Seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3IntervalPSESs | 1.3.6.1.2.1.10.30.7.1.4 | ||
| The counter associated with the number of P-bit Severely Errored Seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3IntervalSEFSs | 1.3.6.1.2.1.10.30.7.1.5 | ||
| The counter associated with the number of Severely Errored Framing Seconds, encountered by a DS3/E3 interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3IntervalUASs | 1.3.6.1.2.1.10.30.7.1.6 | ||
| The counter associated with the number of Unavailable Seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3IntervalLCVs | 1.3.6.1.2.1.10.30.7.1.7 | ||
| The counter associated with the number of Line Coding Violations encountered by a DS3/E3 interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3IntervalPCVs | 1.3.6.1.2.1.10.30.7.1.8 | ||
| The counter associated with the number of P-bit Coding Violations, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3IntervalLESs | 1.3.6.1.2.1.10.30.7.1.9 | ||
| The number of Line Errored Seconds (BPVs or illegal zero sequences) encountered by a DS3/E3 interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3IntervalCCVs | 1.3.6.1.2.1.10.30.7.1.10 | ||
| The number of C-bit Coding Violations encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3IntervalCESs | 1.3.6.1.2.1.10.30.7.1.11 | ||
| The number of C-bit Errored Seconds encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3IntervalCSESs | 1.3.6.1.2.1.10.30.7.1.12 | ||
| The number of C-bit Severely Errored Seconds encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3TotalTable | 1.3.6.1.2.1.10.30.8 | ||
| The DS3/E3 Total table. 24 hour interval. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| Dsx3TotalEntry | |||
| dsx3TotalEntry | 1.3.6.1.2.1.10.30.8.1 | ||
| An entry in the DS3/E3 Total table. | |||
| OBJECT-TYPE | |||
| Dsx3TotalEntry | |||
| dsx3TotalIndex | 1.3.6.1.2.1.10.30.8.1.1 | ||
| The index value which uniquely identifies the DS3/E3 interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value an dsx3LineIndex object instance. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| dsx3TotalPESs | 1.3.6.1.2.1.10.30.8.1.2 | ||
| The counter associated with the number of P-bit Errored Seconds, encountered by a DS3 interface in the previous 24 hour interval | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3TotalPSESs | 1.3.6.1.2.1.10.30.8.1.3 | ||
| The counter associated with the number of P-bit Severely Errored Seconds, encountered by a DS3 interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3TotalSEFSs | 1.3.6.1.2.1.10.30.8.1.4 | ||
| The counter associated with the number of Severely Errored Framing Seconds, encountered by a DS3/E3 interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3TotalUASs | 1.3.6.1.2.1.10.30.8.1.5 | ||
| The counter associated with the number of Unavailable Seconds, encountered by a DS3 interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3TotalLCVs | 1.3.6.1.2.1.10.30.8.1.6 | ||
| The counter associated with the number of Line Coding Violations encountered by a DS3/E3 interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3TotalPCVs | 1.3.6.1.2.1.10.30.8.1.7 | ||
| The counter associated with the number of P-bit Coding Violations, encountered by a DS3 interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3TotalLESs | 1.3.6.1.2.1.10.30.8.1.8 | ||
| The number of Line Errored Seconds (BPVs or illegal zero sequences) encountered by a DS3/E3 interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3TotalCCVs | 1.3.6.1.2.1.10.30.8.1.9 | ||
| The number of C-bit Coding Violations encountered by a DS3 interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3TotalCESs | 1.3.6.1.2.1.10.30.8.1.10 | ||
| The number of C-bit Errored Seconds encountered by a DS3 interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3TotalCSESs | 1.3.6.1.2.1.10.30.8.1.11 | ||
| The number of C-bit Severely Errored Seconds encountered by a DS3 interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3FarEndConfigTable | 1.3.6.1.2.1.10.30.9 | ||
| The DS3 Far End Configuration table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| Dsx3FarEndConfigEntry | |||
| dsx3FarEndConfigEntry | 1.3.6.1.2.1.10.30.9.1 | ||
| An entry in the DS3 Far End Configuration table. | |||
| OBJECT-TYPE | |||
| Dsx3FarEndConfigEntry | |||
| dsx3FarEndLineIndex | 1.3.6.1.2.1.10.30.9.1.1 | ||
| The index value which uniquely identifies the DS3 interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value an dsx3LineIndex object instance. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| dsx3FarEndEquipCode | 1.3.6.1.2.1.10.30.9.1.2 | ||
| This is the Far End Equipment Identification code that describes the specific piece of equipment. It is sent within the Path Identification Message. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..10) | ||
| dsx3FarEndLocationIDCode | 1.3.6.1.2.1.10.30.9.1.3 | ||
| This is the Far End Location Identification code that describes the specific location of the equipment. It is sent within the Path Identification Message. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..11) | ||
| dsx3FarEndFrameIDCode | 1.3.6.1.2.1.10.30.9.1.4 | ||
| This is the Far End Frame Identification code that identifies where the equipment is located within a building at a given location. It is sent within the Path Identification Message. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..10) | ||
| dsx3FarEndUnitCode | 1.3.6.1.2.1.10.30.9.1.5 | ||
| This is the Far End code that identifies the equipment location within a bay. It is sent within the Path Identification Message. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..6) | ||
| dsx3FarEndFacilityIDCode | 1.3.6.1.2.1.10.30.9.1.6 | ||
| This code identifies a specific Far End DS3 path. It is sent within the Path Identification Message. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..38) | ||
| dsx3FarEndCurrentTable | 1.3.6.1.2.1.10.30.10 | ||
| The DS3 Far End Current table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| Dsx3FarEndCurrentEntry | |||
| dsx3FarEndCurrentEntry | 1.3.6.1.2.1.10.30.10.1 | ||
| An entry in the DS3 Far End Current table. | |||
| OBJECT-TYPE | |||
| Dsx3FarEndCurrentEntry | |||
| dsx3FarEndCurrentIndex | 1.3.6.1.2.1.10.30.10.1.1 | ||
| The index value which uniquely identifies the DS3 interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value an dsx3LineIndex object instance. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| dsx3FarEndTimeElapsed | 1.3.6.1.2.1.10.30.10.1.2 | ||
| The number of seconds that have elapsed since the beginning of the far end current error-measurement period. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..899 | ||
| dsx3FarEndValidIntervals | 1.3.6.1.2.1.10.30.10.1.3 | ||
| The number of previous far end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute far end intervals since the interface has been online. | |||
| OBJECT-TYPE | |||
| INTEGER | 0..96 | ||
| dsx3FarEndCurrentCESs | 1.3.6.1.2.1.10.30.10.1.4 | ||
| The counter associated with the number of Far Far End C-bit Errored Seconds encountered by a DS3 interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3FarEndCurrentCSESs | 1.3.6.1.2.1.10.30.10.1.5 | ||
| The counter associated with the number of Far End C-bit Severely Errored Seconds encountered by a DS3 interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3FarEndCurrentCCVs | 1.3.6.1.2.1.10.30.10.1.6 | ||
| The counter associated with the number of Far End C-bit Coding Violations reported via the far end block error count encountered by a DS3 interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3FarEndCurrentUASs | 1.3.6.1.2.1.10.30.10.1.7 | ||
| The counter associated with the number of Far End unavailable seconds encountered by a DS3 interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3FarEndIntervalTable | 1.3.6.1.2.1.10.30.11 | ||
| The DS3 Far End Interval table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| Dsx3FarEndIntervalEntry | |||
| dsx3FarEndIntervalEntry | 1.3.6.1.2.1.10.30.11.1 | ||
| An entry in the DS3 Far End Interval table. | |||
| OBJECT-TYPE | |||
| Dsx3FarEndIntervalEntry | |||
| dsx3FarEndIntervalIndex | 1.3.6.1.2.1.10.30.11.1.1 | ||
| The index value which uniquely identifies the DS3 interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value an dsx3LineIndex object instance. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| dsx3FarEndIntervalNumber | 1.3.6.1.2.1.10.30.11.1.2 | ||
| A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid). | |||
| OBJECT-TYPE | |||
| INTEGER | 1..96 | ||
| dsx3FarEndIntervalCESs | 1.3.6.1.2.1.10.30.11.1.3 | ||
| The counter associated with the number of Far End C-bit Errored Seconds encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3FarEndIntervalCSESs | 1.3.6.1.2.1.10.30.11.1.4 | ||
| The counter associated with the number of Far End C-bit Severely Errored Seconds encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3FarEndIntervalCCVs | 1.3.6.1.2.1.10.30.11.1.5 | ||
| The counter associated with the number of Far End C-bit Coding Violations reported via the far end block error count encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3FarEndIntervalUASs | 1.3.6.1.2.1.10.30.11.1.6 | ||
| The counter associated with the number of Far End unavailable seconds encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3FarEndTotalTable | 1.3.6.1.2.1.10.30.12 | ||
| The DS3 Far End Total table. 24 hour interval. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| Dsx3FarEndTotalEntry | |||
| dsx3FarEndTotalEntry | 1.3.6.1.2.1.10.30.12.1 | ||
| An entry in the DS3 Far End Total table. | |||
| OBJECT-TYPE | |||
| Dsx3FarEndTotalEntry | |||
| dsx3FarEndTotalIndex | 1.3.6.1.2.1.10.30.12.1.1 | ||
| The index value which uniquely identifies the DS3 interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value an dsx3LineIndex object instance. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..65535 | ||
| dsx3FarEndTotalCESs | 1.3.6.1.2.1.10.30.12.1.2 | ||
| The counter associated with the number of Far End C-bit Errored Seconds encountered by a DS3 interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3FarEndTotalCSESs | 1.3.6.1.2.1.10.30.12.1.3 | ||
| The counter associated with the number of Far End C-bit Severely Errored Seconds encountered by a DS3 interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3FarEndTotalCCVs | 1.3.6.1.2.1.10.30.12.1.4 | ||
| The counter associated with the number of Far End C-bit Coding Violations reported via the far end block error count encountered by a DS3 interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3FarEndTotalUASs | 1.3.6.1.2.1.10.30.12.1.5 | ||
| The counter associated with the number of Far End unavailable seconds encountered by a DS3 interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge | |||
| dsx3FracTable | 1.3.6.1.2.1.10.30.13 | ||
| The DS3 Fractional table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| Dsx3FracEntry | |||
| dsx3FracEntry | 1.3.6.1.2.1.10.30.13.1 | ||
| An entry in the DS3 Fractional table. | |||
| OBJECT-TYPE | |||
| Dsx3FracEntry | |||
| dsx3FracIndex | 1.3.6.1.2.1.10.30.13.1.1 | ||
| The index value which uniquely identifies the DS3 interface to which this entry is applicable The interface identified by a particular value of this index is the same interface as identified by the same value an dsx3LineIndex object instance. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..'7fffffff'h | ||
| dsx3FracNumber | 1.3.6.1.2.1.10.30.13.1.2 | ||
| The channel number for this entry. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..31 | ||
| dsx3FracIfIndex | 1.3.6.1.2.1.10.30.13.1.3 | ||
| An index value that uniquely identifies an interface. The interface identified by a particular value of this index is the same interface as identified by the same value an ifIndex object instance. If no interface is currently using a channel, the value should be zero. If a single interface occupies more than one time slot, that ifIndex value will be found in multiple time slots. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..'7fffffff'h | ||
| Dsx3ConfigEntry | |||
| SEQUENCE | |||
| INTEGER as dsx3LineIndex | |||
| INTEGER as dsx3IfIndex | |||
| INTEGER as dsx3TimeElapsed | |||
| INTEGER as dsx3ValidIntervals | |||
| INTEGER as dsx3LineType | |||
| INTEGER as dsx3LineCoding | |||
| INTEGER as dsx3SendCode | |||
| DisplayString as dsx3CircuitIdentifier | |||
| INTEGER as dsx3LoopbackConfig | |||
| INTEGER as dsx3LineStatus | |||
| INTEGER as dsx3TransmitClockSource | |||
| Dsx3CurrentEntry | |||
| SEQUENCE | |||
| INTEGER as dsx3CurrentIndex | |||
| Gauge as dsx3CurrentPESs | |||
| Gauge as dsx3CurrentPSESs | |||
| Gauge as dsx3CurrentSEFSs | |||
| Gauge as dsx3CurrentUASs | |||
| Gauge as dsx3CurrentLCVs | |||
| Gauge as dsx3CurrentPCVs | |||
| Gauge as dsx3CurrentLESs | |||
| Gauge as dsx3CurrentCCVs | |||
| Gauge as dsx3CurrentCESs | |||
| Gauge as dsx3CurrentCSESs | |||
| Dsx3IntervalEntry | |||
| SEQUENCE | |||
| INTEGER as dsx3IntervalIndex | |||
| INTEGER as dsx3IntervalNumber | |||
| Gauge as dsx3IntervalPESs | |||
| Gauge as dsx3IntervalPSESs | |||
| Gauge as dsx3IntervalSEFSs | |||
| Gauge as dsx3IntervalUASs | |||
| Gauge as dsx3IntervalLCVs | |||
| Gauge as dsx3IntervalPCVs | |||
| Gauge as dsx3IntervalLESs | |||
| Gauge as dsx3IntervalCCVs | |||
| Gauge as dsx3IntervalCESs | |||
| Gauge as dsx3IntervalCSESs | |||
| Dsx3TotalEntry | |||
| SEQUENCE | |||
| INTEGER as dsx3TotalIndex | |||
| Gauge as dsx3TotalPESs | |||
| Gauge as dsx3TotalPSESs | |||
| Gauge as dsx3TotalSEFSs | |||
| Gauge as dsx3TotalUASs | |||
| Gauge as dsx3TotalLCVs | |||
| Gauge as dsx3TotalPCVs | |||
| Gauge as dsx3TotalLESs | |||
| Gauge as dsx3TotalCCVs | |||
| Gauge as dsx3TotalCESs | |||
| Gauge as dsx3TotalCSESs | |||
| Dsx3FarEndConfigEntry | |||
| SEQUENCE | |||
| INTEGER as dsx3FarEndLineIndex | |||
| DisplayString as dsx3FarEndEquipCode | |||
| DisplayString as dsx3FarEndLocationIDCode | |||
| DisplayString as dsx3FarEndFrameIDCode | |||
| DisplayString as dsx3FarEndUnitCode | |||
| DisplayString as dsx3FarEndFacilityIDCode | |||
| Dsx3FarEndCurrentEntry | |||
| SEQUENCE | |||
| INTEGER as dsx3FarEndCurrentIndex | |||
| INTEGER as dsx3FarEndTimeElapsed | |||
| INTEGER as dsx3FarEndValidIntervals | |||
| Gauge as dsx3FarEndCurrentCESs | |||
| Gauge as dsx3FarEndCurrentCSESs | |||
| Gauge as dsx3FarEndCurrentCCVs | |||
| Gauge as dsx3FarEndCurrentUASs | |||
| Dsx3FarEndIntervalEntry | |||
| SEQUENCE | |||
| INTEGER as dsx3FarEndIntervalIndex | |||
| INTEGER as dsx3FarEndIntervalNumber | |||
| Gauge as dsx3FarEndIntervalCESs | |||
| Gauge as dsx3FarEndIntervalCSESs | |||
| Gauge as dsx3FarEndIntervalCCVs | |||
| Gauge as dsx3FarEndIntervalUASs | |||
| Dsx3FarEndTotalEntry | |||
| SEQUENCE | |||
| INTEGER as dsx3FarEndTotalIndex | |||
| Gauge as dsx3FarEndTotalCESs | |||
| Gauge as dsx3FarEndTotalCSESs | |||
| Gauge as dsx3FarEndTotalCCVs | |||
| Gauge as dsx3FarEndTotalUASs | |||
| Dsx3FracEntry | |||
| SEQUENCE | |||
| INTEGER as dsx3FracIndex | |||
| INTEGER as dsx3FracNumber | |||
| INTEGER as dsx3FracIfIndex | |||