S5-AGENT-MIB

File: S5-AGENT-MIB.mib (55103 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
S5-ROOT-MIB S5-TCS-MIB SNMPv2-TC

Imported symbols

IpAddress TimeTicks OBJECT-TYPE
DisplayString s5Agent TimeIntervalSec
IpxAddress MacAddress

Defined Objects

s5AgentHw 1.3.6.1.4.1.45.1.6.4.1
OBJECT IDENTIFIER    

s5AgMyGrpIndx 1.3.6.1.4.1.45.1.6.4.1.1
The index of the group containing the agent.
OBJECT-TYPE    
  INTEGER 1..32767  

s5AgMyComIndx 1.3.6.1.4.1.45.1.6.4.1.2
The index of the component containing the agent.
OBJECT-TYPE    
  INTEGER 1..32767  

s5AgentInfo 1.3.6.1.4.1.45.1.6.4.2
OBJECT IDENTIFIER    

s5AgentGbl 1.3.6.1.4.1.45.1.6.4.2.1
OBJECT IDENTIFIER    

s5AgInfoReBoot 1.3.6.1.4.1.45.1.6.4.2.1.1
Action object to reboot the agent. The following values can only be read: other(1).....agent in unknown or other state running(2)...agent running The following values can be written: restart(3)...restart agent (i.e., jump to beginning of agent code) reboot(4)....start boot sequence for agent (i.e., jump to beginning of boot firmware) reset(5).....do a hardware reset download(6)..............activate download of a new agent downloadAndRestart(7)....activate download of a new agent and restart downloadAndReboot(8).....activate download of a new agent and reboot downloadAndReset(9)......activate download of a new agent and reset If s5AgInfoScheduleBootTime is set in the same PDU as s5AgInfoReBoot, the action specified occurs when the scheduled time reaches zero; otherwise, the action occurs immediately. The agent does best efforts to return a response before the action occurs. If any of the combined download actions are requested, neither action occurs until the expiry of s5AgInfoScheduleBootTime, if set.
OBJECT-TYPE    
  INTEGER other(1), running(2), restart(3), reboot(4), reset(5), download(6), downloadAndRestart(7), downloadAndReboot(8), downloadAndReset(9)  

s5AgInfoWriteCfg 1.3.6.1.4.1.45.1.6.4.2.1.2
Action object to cause current configuration settings to be written to local nonvolatile storage. The following values can only be read: other(1)...some unknown or other state valid(2)...contents valid The following value can be written: write(3)...write configuration settings to local storage (such as nonvol) If the write operation write fails, then the agent will return error 'genErr' on the SET.
OBJECT-TYPE    
  INTEGER other(1), valid(2), write(3)  

s5AgInfoMgmtProtocolNxtBoot 1.3.6.1.4.1.45.1.6.4.2.1.3
The transport protocol(s) to use after the next boot of the agent. The following value is read-only: other(1)....unknown or some other protocol The following value is read-write: ipOnly(2).....only IP ipxOnly(3)....only IPX ipAndIpx(4)...IP and IPX.
OBJECT-TYPE    
  INTEGER other(1), ipOnly(2), ipxOnly(3), ipAndIpx(4)  

s5AgInfoMgmtProtocolCur 1.3.6.1.4.1.45.1.6.4.2.1.4
The current transport protocol(s) that are being supported by the agent. The following value is read-only: other(1)....unknown or some other protocol The following value is read-write: ipOnly(2).....only IP ipxOnly(3)....only IPX ipAndIpx(4)...IP and IPX. When the IP protocol stack is not enabled, the agent will not respond to PING or SNMP requests over IP. When the IPX protocol stack is not enabled, the agent will not respond to diagnostic SAP or SNMP requests over IPX. It is suggested that NMS not disable the transport they are using.
OBJECT-TYPE    
  INTEGER other(1), ipOnly(2), ipxOnly(3), ipAndIpx(4)  

s5AgInfoBootMode 1.3.6.1.4.1.45.1.6.4.2.1.5
The source for initial protocol configuration information at next boot. For IP, a setting of net(3), netWhenNeeded(4), or netOrLastAddress(5) means that BOOTP will be used to get the agent's IP address(es), load server address, and configuration file name. For IPX, a setting of net(3), netWhenNeeded(4), or netOrLastAddress(5) means SAP will be used to get the agent's Novell network number(s), and the configuation filename will be loaded from local storage (note - the load server address is not needed in a Novell network). The following value is read-only: other(1).....not applicable or some other case The following values are read-write: local(2) Don't use the network. net(3) Try using the network and if that fails then use protocol configuration information from local storage. netWhenNeeded(4) Use protocol configuration information from local storage if available, otherwise, try using the network. netOrLastAddress(5) Similar to netWhenNeeded, except that if using the network fails, the last set of protocol configuration information that was obtained using the network will be used if it is available. Note: The load server address is not configurable and is not available in this MIB object on a Novell network.
OBJECT-TYPE    
  INTEGER other(1), local(2), net(3), netWhenNeeded(4), netOrLastAddress(5)  

s5AgInfoCfgLoadMode 1.3.6.1.4.1.45.1.6.4.2.1.6
The source from which to load configuration information at next boot. The following value is read-only: other(1)...not applicable or some other case The following values are read-write: local(2).....get from local storage net(3).......load from the network locAsBk(4)...try using network and if it fails then use local information. When local(2) is specified, the configuration information is loaded from local storage. If the local configuration is not valid (checks for ip = 0.0.0.0), then BOOTP is used for the IP stack. (In IPX only mode, the IP address could be 0.0.0.0 and IPX does not rely on the IP address. The agent checks the IPX address, and if the network number of the IPX address is equal to 0 the agent uses SAP). When net(3) is specified, the configuration information will be downloaded from the network only. The configuration information will never be loaded from local storage, even if downloading fails and the local configuration information exists. When locAsBk(4) is specified, a download of the configuration information will be tried over the network. If the network download fails then the configuration information will be loaded from local storage.
OBJECT-TYPE    
  INTEGER other(1), local(2), net(3), locAsBk(4)  

s5AgInfoImgLoadMode 1.3.6.1.4.1.45.1.6.4.2.1.7
The source from which to load the agent image at next boot. The following value is read-only: other(1)...not applicable or some other case The following values are read-write: local(2)........get from local storage net(3)..........load from the network locAsBk(4)......try using network and if it fails then use local information. netIfNewer(5)...try loading image over the net. If can load image, and it is newer than the local image, then use it. Otherwise, use local image. If the local image is not valid, the setting will be net(3) and cannot be changed to local(2), or locAsBk(4) until a valid image file is loaded (i.e., error 'badValue' will be returned on SETS with value other than net(3)). When the local image is not valid and the network download of the image fails, the entire boot process will be repeated. When local(2) is specified, the image will be loaded from local storage. When net(3) is specified, the image will be downloaded from the network only. The image file will never be loaded from local storage, even if downloading fails and the local image exists. When locAsBk(4) is specified, a download of the image will be tried over the network. If the network download fails then the image is loaded from local storage. When netIfNewer(5) is specified, a download of the image will be tried over the network. If successful, it will then be compared to the image stored in local storage. The most recent version of the two will be used. If the local image is not valid, the network will always be used. If the network download fails then the image is loaded from the local storage.
OBJECT-TYPE    
  INTEGER other(1), local(2), net(3), locAsBk(4), netIfNewer(5)  

s5AgInfoImgSaveMode 1.3.6.1.4.1.45.1.6.4.2.1.8
Indicates what to do with the image (when loaded from the network) on the next boot. The following value can only be read: notAvail(1)...the save operation is not available The following values can be written (and read) if the device supports this capability: writeIfDiff(2)....save image to local storage at next boot if image is different from saved contents writeIfNewer(3)...save image to local storage at next boot if image is newer than saved contents. noWrite(4)........do not save image to local storage at next boot, even if image is newer or different.
OBJECT-TYPE    
  INTEGER notAvail(1), writeIfDiff(2), writeIfNewer(3), noWrite(4)  

s5AgInfoImgSaveStatus 1.3.6.1.4.1.45.1.6.4.2.1.9
Indicates what happened to the image file on the last boot. The following values are returned: notAvail(1).....the save operation is not available noSave(2).......image not saved since image was not asked to be saved, or image was not loaded from the network saved(3)........image saved saveFailed(4)...tried to save image, but failed
OBJECT-TYPE    
  INTEGER notAvail(1), noSave(2), saved(3), saveFailed(4)  

s5AgInfoVer 1.3.6.1.4.1.45.1.6.4.2.1.10
The version of the agent in the form 'major.minor.maintenance[letters]'. This is an alias for the value of the object s5ChasStoreCntntVer for the RAM of the module containing the agent.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

s5AgInfoLocStorVer 1.3.6.1.4.1.45.1.6.4.2.1.11
The version of the agent image saved in local storage such as flash memory in the form 'major.minor.maintenance[letters]'. If not known or not available, then the value is a zero length string. This is an alias for the value of the object s5ChasStoreCntntVer for the local storage of the module containing the agent.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

s5AgInfoNxtBootDfltGwAddr 1.3.6.1.4.1.45.1.6.4.2.1.12
The IP address of the default gateway (router) for the agent to use after the next boot. (NOTE: the current default router is the value of object s5AgInfoCurDfltGwAddr (or ipRouteNextHop.0.0.0.0).) If not used, then this object has the value of 0.0.0.0.
OBJECT-TYPE    
  IpAddress  

s5AgInfoCurDfltGwAddr 1.3.6.1.4.1.45.1.6.4.2.1.13
The IP address of the current default gateway (router). (NOTE: this is an alias for the object ipRouteNextHop in the row of the table ipRouteTable which has object ipRouteDest with a value of 0.0.0.0.) If not used, then this object has the value of 0.0.0.0.
OBJECT-TYPE    
  IpAddress  

s5AgInfoDramUsage 1.3.6.1.4.1.45.1.6.4.2.1.14
An indication of the percentage of DRAM currently in use by this agent. If this information is not available the agent shall return -1, otherwise the percentage of DRAM in use is returned as an integer between 0 and 100. The percentage is defined as the DRAM currently used by this agent divided by the total DRAM available to this agent.
OBJECT-TYPE    
  INTEGER -1..100  

s5AgInfoLoadProtocolNxtBoot 1.3.6.1.4.1.45.1.6.4.2.1.15
The transport protocol(s) over which the agent is to use to load the configuration information and the agent image at the next boot of the agent. The following value is read-only: other(1)....unknown or some other protocol The following values are read-write: ipOnly(2)....use load protocol over IP ipxOnly(3)...use load protocol over IPX auto(4)......try using the IP load function and if that fails then use IPX load function. If the IPX load function also fails, repeat the same process until one or the other protocol succeeds.
OBJECT-TYPE    
  INTEGER other(1), ipOnly(2), ipxOnly(3), auto(4)  

s5AgInfoLoadProtocolLast 1.3.6.1.4.1.45.1.6.4.2.1.16
The transport protocol over which the agent image and configuration information were last loaded. The following values are read-only: reserved(1)...reserved ip(2).........gotten from the network using a load protocol over IP ipx(3)........gotten from the network using a load protocol over IPX local(4)......loaded from local storage.
OBJECT-TYPE    
  INTEGER reserved(1), ip(2), ipx(3), local(4)  

s5AgInfoSlotScope 1.3.6.1.4.1.45.1.6.4.2.1.17
This object contains information about all the slots an agent can manage. The value is encoded in an octet string. One byte has information about 8 slots. If a bit is set then agent can manage the corresponding slot. Byte 1 will have information about slots 1-8, byte 2 will have information about slots 9-16, and so on. For example an agent that can manage slots 2-7 in a 14 slot chassis should have the value : 8d:00 (0111 1110 0000 0000) If an agent returns a string of size 0, then it can manage all slots in chassis.
OBJECT-TYPE    
  OCTET STRING  

s5AgInfoImgType 1.3.6.1.4.1.45.1.6.4.2.1.18
Indicates the type of agent image. This object is meant to distinguish between agents having the same version number running on the same hardware, but with dissimilar functionality. Following are examples of possible values for various enumerations. other(1) ....... A unique agent eg., 5310A, 5dn310 etc typeA(2) ....... fusion basic agent. typeB(2) ....... fusion advanced agent.
OBJECT-TYPE    
  INTEGER other(1), typeA(2), typeB(3), typeC(4)  

s5AgInfoScheduleBootTime 1.3.6.1.4.1.45.1.6.4.2.1.19
The time, measured in minutes, remaining until the action(s) set by s5AgInfoReBoot will be performed. This value must be set in the same set request as the value of s5AgInfoReBoot; otherwise, a badValue error is returned. If this value has been set, the number returned will count down to zero, and the time remaining in minutes will be rounded up to the next whole minute. Actions set via s5AgInfoReBoot can be scheduled for up to seven days in advance. 7 * 24 * 60 equals the maximum settable value of 10080. If this attribute has not been set, a value of zero should be returned.
OBJECT-TYPE    
  INTEGER 0..10080  

s5AgInfoScheduleBootCancel 1.3.6.1.4.1.45.1.6.4.2.1.20
Cancel a scheduled s5AgInfoReboot action. The following value is read-only: other(1)...not applicable or some other case This is always the value that return when read. The following values are read-write: cancel(2)...cancel a scheduled boot. Setting this attribute to cancel(2) sets s5AgInfoReBoot to running(2) and s5AgInfoScheduleBootTime to zero.
OBJECT-TYPE    
  INTEGER other(1), cancel(2)  

s5AgInfoNumBootBanks 1.3.6.1.4.1.45.1.6.4.2.1.21
The number of local storage locations (or flash memory banks) available on this device for operational code images. Devices without local image capability or not supporting this attribute shall return a value of 0.
OBJECT-TYPE    
  INTEGER 0..255  

s5AgInfoNextBootBank 1.3.6.1.4.1.45.1.6.4.2.1.22
The source of the image to be loaded upon the next boot of the device. If a value is set larger than s5AgInfoNumBootBanks, a badValue error should be returned. Devices without local image capability or not supporting this attribute shall return a value of 0.
OBJECT-TYPE    
  INTEGER 0..255  

s5AgInfoDstLoadBank 1.3.6.1.4.1.45.1.6.4.2.1.23
The local storage bank where the next system image image is downloaded to. Devices without local image capability or not supporting this attribute shall return a value of 0.
OBJECT-TYPE    
  INTEGER 0..255  

s5AgInfoFileAction 1.3.6.1.4.1.45.1.6.4.2.1.24
This object is used to download or upload a config file or an image file. In read operation, if no action taken since the boot up, it will return other(1). Otherwise it will return the latest action such as dnldConfig(2), dnldImg(3), upldConfig(4) and upldImg(5). In write operation, the values that can be written are: dnldConfig(2) ... download a config file to a device. The new config file will not take effect until the next boot cycle of the device. dnldImg(3) ...... download an image to a device. upldConfig(4) ... upload a config file to a server from a device. The config file contains the current MIB object values of the device. upldImg(5) ...... upload a image from a device to a server dnldFw(6) ....... download firmware to a device upldFw(7) ....... upload firware from a device to a server dnldImgIfNewer(8) download an image to a device if the image version is newer than the image stored in local NV storage
OBJECT-TYPE    
  INTEGER other(1), dnldConfig(2), dnldImg(3), upldConfig(4), upldImg(5), dnldFw(6), upldFw(7), dnldImgIfNewer(8)  

s5AgInfoFileStatus 1.3.6.1.4.1.45.1.6.4.2.1.25
This object is used to get the status of the latest action as shown by s5AgInfoFileAction. The values that can be read are: other(1) ......... if no action taken since the boot up inProgress (2) ... the operation is in progress success (3) ...... the operation succeeds. fail (4) ......... the operation is failed.
OBJECT-TYPE    
  INTEGER other(1), inProgress(2), success(3), fail(4)  

s5AgInfoStackBootpMACUsage 1.3.6.1.4.1.45.1.6.4.2.1.26
This object is used to get/set which MAC address is used by a stackable system when performing BOOTP requests during bootup. A value of useBaseUnitMACAddress(2) indicates that the MAC address of the base unit of the stack will be used. A value of useStackMACAddress(3) indicates that the MAC address of the stack will be used.
OBJECT-TYPE    
  INTEGER other(1), useBaseUnitMACAddress(2), useStackMACAddress(3)  

s5AgMyIfTable 1.3.6.1.4.1.45.1.6.4.2.2
A table that provides additional information about the agent's interfaces. The number of entries in the table is determined by the number of interfaces on the agent.
OBJECT-TYPE    
  SEQUENCE OF  
    S5AgMyIfEntry

s5AgMyIfEntry 1.3.6.1.4.1.45.1.6.4.2.2.1
A row in the table of additional information about the agent's interfaces. Entries can not be created or deleted via SNMP requests.
OBJECT-TYPE    
  S5AgMyIfEntry  

s5AgMyIfIndx 1.3.6.1.4.1.45.1.6.4.2.2.1.1
The index of the interface. This has the same value as ifIndex for the interface.
OBJECT-TYPE    
  INTEGER  

s5AgMyIfNxtBootIpAddr 1.3.6.1.4.1.45.1.6.4.2.2.1.2
For the next boot, the IP address of the the interface. If not used, then the value is 0.0.0.0. (NOTE: the current IP address for the interface is found in table ipAddrTable and in table s5AgOthIfTable.)
OBJECT-TYPE    
  IpAddress  

s5AgMyIfNxtBootNetMask 1.3.6.1.4.1.45.1.6.4.2.2.1.3
For the next boot, the subnet mask for the interface. If not used, then the value is 0.0.0.0. (NOTE: the current subnet mask for the interface is found in table ipAddrTable.)
OBJECT-TYPE    
  IpAddress  

s5AgMyIfCfgFname 1.3.6.1.4.1.45.1.6.4.2.2.1.4
Name of the configuration file currently associated with the interface. When not used, the value is a zero length string.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

s5AgMyIfLdSvrAddr 1.3.6.1.4.1.45.1.6.4.2.2.1.5
The IP address of the load server for the configuration file and/or the image file. If not used, then the value is 0.0.0.0
OBJECT-TYPE    
  IpAddress  

s5AgMyIfImgFname 1.3.6.1.4.1.45.1.6.4.2.2.1.6
Name of the image file(s) currently associated with the interface. Some agents in special situations may support a value which contains multiple file names instead of a single file name. Multiple names are specified as a list of file names separated by semicolons (;). When the object is not used, the value is a zero length string.
OBJECT-TYPE    
  DisplayString SIZE(0..128)  

s5AgMyIfValidFlag 1.3.6.1.4.1.45.1.6.4.2.2.1.7
Indicates if the configuration and/or image file(s) were downloaded from this interface and if the file names have not been changed. The following values can be read: valid(1).....configuration and/or image file(s) downloaded from this interface are currently in use invalid(2)...cfg and/or image files downloaded from this interface are not in use (this may also mean that there are no files downloaded from this interface).
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

s5AgMyIfNxtBootIpxAddr 1.3.6.1.4.1.45.1.6.4.2.2.1.8
For the next boot, the IPX address of the the interface. If the IPX protocol is not used, then the value is 00000000:000000000000. NOTE: The current IPX address for the interface is found in table s5AgOthIfTable.
OBJECT-TYPE    
  IpxAddress  

s5AgMyIfBootRouterAddr 1.3.6.1.4.1.45.1.6.4.2.2.1.9
The IP address of the boot router for the configuration file and/or the image file. If not used, then the value is 0.0.0.0
OBJECT-TYPE    
  IpAddress  

s5AgMyIfMacAddr 1.3.6.1.4.1.45.1.6.4.2.2.1.10
The MAC address of the interface. The value is 00:00:00:00:00:00 if there is no interface.
OBJECT-TYPE    
  MacAddress  

s5AgOthIfTable 1.3.6.1.4.1.45.1.6.4.2.3
A table that provides information about each interface for each agent in the chassis. The number of entries in the table is determined by the number of agents in the chassis and their configuration.
OBJECT-TYPE    
  SEQUENCE OF  
    S5AgOthIfEntry

s5AgOthIfEntry 1.3.6.1.4.1.45.1.6.4.2.3.1
A row in the table of information about interface information for all agents in the chassis. Entries can not be created or deleted via SNMP requests.
OBJECT-TYPE    
  S5AgOthIfEntry  

s5AgOthIfGrpIndx 1.3.6.1.4.1.45.1.6.4.2.3.1.1
The index of the group containing the component containing the agent.
OBJECT-TYPE    
  INTEGER 1..32767  

s5AgOthIfComIndx 1.3.6.1.4.1.45.1.6.4.2.3.1.2
The index of the component in the group containing the agent.
OBJECT-TYPE    
  INTEGER 1..32767  

s5AgOthIfIndx 1.3.6.1.4.1.45.1.6.4.2.3.1.3
The index of the interface. This is the same value as ifIndex.
OBJECT-TYPE    
  INTEGER  

s5AgOthIfIpAddr 1.3.6.1.4.1.45.1.6.4.2.3.1.4
The IP address of the interface. If not used, then the value is 0.0.0.0.
OBJECT-TYPE    
  IpAddress  

s5AgOthIfIpxAddr 1.3.6.1.4.1.45.1.6.4.2.3.1.5
The IPX address of the interface. If the IPX protocol is not used, then the value is 00000000:000000000000.
OBJECT-TYPE    
  IpxAddress  

s5AgIpRtrDefaultTimeToLive 1.3.6.1.4.1.45.1.6.4.2.4
The lifetime of IP router entries in seconds. The maximum length of time that a IP router is to be considered alive in the absence of further positive advice. The default lifetime is used for routers learned through IP router protocols that do not specify a lifetime (e.g. statically configured, ICMP redirects).
OBJECT-TYPE    
  TimeIntervalSec 60..3600  

s5AgIpDefaultRtrSelectionMode 1.3.6.1.4.1.45.1.6.4.2.5
The method used to select a default IP router. The following value is read-only: other(1).......not applicable or other case The following values are read-write: config(2).....use configured primary default router. If no primary default router is specified, there will be no default IP route. static(3).....A default router will be chose from the routers known to be up and that have been configured. dynamic(4)....ICMP router discovery as per RFC 1256 is performed and the router with the highest preference level is chosen as default router.
OBJECT-TYPE    
  INTEGER other(1), config(2), static(3), dynamic(4)  

s5AgIpRtrDiscoverySolicitMode 1.3.6.1.4.1.45.1.6.4.2.6
The router discovery solicitation mode to use when the default router selection mode is dynamic. This solicitation mode determines the IP address for ICMP router solicitations (see RFC 1256): multicast(1)..router solicitations are sent to the all-routers multicast address (224.0.0.2) broadcast(2)..router solicitations are sent to the limited broadcast address (255.255.255.255).
OBJECT-TYPE    
  INTEGER multicast(1), broadcast(2)  

s5AgDataCollectTable 1.3.6.1.4.1.45.1.6.4.2.7
A table of control information and statistics for the data collection (promiscuous data capturing) per source of detection.
OBJECT-TYPE    
  SEQUENCE OF  
    S5AgDataCollectEntry

s5AgDataCollectEntry 1.3.6.1.4.1.45.1.6.4.2.7.1
A row in the data collection table. Entries can not be created or deleted via SNMP.
OBJECT-TYPE    
  S5AgDataCollectEntry  

s5AgDataCollectIfIndex 1.3.6.1.4.1.45.1.6.4.2.7.1.1
An integer value representing the source that collects data from the network. A value greater than zero is the index of the agent's interface on the NMM. This is the same value as ifIndex for the interface. A value of zero indicates data collection via best available efforts (other than NMM's interfaces).
OBJECT-TYPE    
  INTEGER 0..255  

s5AgDataCollectSnTimeStamp 1.3.6.1.4.1.45.1.6.4.2.7.1.2
The value of sysUpTime at the last time a node was added or deleted from the Show Node table.
OBJECT-TYPE    
  TimeTicks  

s5AgDataCollectNetworkAddrStatus 1.3.6.1.4.1.45.1.6.4.2.7.1.3
A switch to enable or disable the collecting of network layer addresses for the network address mapping table (s5CmNetAddrTable ). The following value is read-only: alwaysOff(1)..data source is not capable of collecting or decoding network addresses The following values are read-write if the data source is capable of collecting network addresses: on(2).........packet decoding is enabled off(3)........packet decoding is disabled or not supported.
OBJECT-TYPE    
  INTEGER alwaysOff(1), on(2), off(3)  

s5AgUnAuthIpAddr 1.3.6.1.4.1.45.1.6.4.2.8
This object contains the IP address of the last station that tried to access this agent with an invalid community string. This object is used as a VarBind in an Authentication Trap PDU. A get request will return the last value used, and will return the null address 0.0.0.0 if no IP authentication traps have been sent.
OBJECT-TYPE    
  IpAddress  

s5AgUnAuthIpxAddr 1.3.6.1.4.1.45.1.6.4.2.9
This object contains the IPX address of the last station that tried to access this agent with an invalid community string. This object is used as a VarBind in an Authentication Trap PDU. A get request will return the last value used, and will return the null address of all zeros if no IPX authentication traps have been sent.
OBJECT-TYPE    
  IpxAddress  

s5AgUnAuthComm 1.3.6.1.4.1.45.1.6.4.2.10
This object contains the community string of the last unauthenticated attempt to access this agent. This object is used as a VarBind in an Authentication Trap PDU. A get request will return the last value used, and will return the null string if no authentication traps have been sent.
OBJECT-TYPE    
  OCTET STRING SIZE(0..20)  

s5AgTrapFilterTable 1.3.6.1.4.1.45.1.6.4.2.11
Agent Trap filter configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    S5AgTrapFilterEntry

s5AgTrapFilterEntry 1.3.6.1.4.1.45.1.6.4.2.11.1
A list of trap filter entries that determine the filtering of traps. For example, an instance of the s5AgtTrapFilterStatus will be named s5AgTrapFilterStatus.8
OBJECT-TYPE    
  S5AgTrapFilterEntry  

s5AgTrapFilterIndex 1.3.6.1.4.1.45.1.6.4.2.11.1.1
An index that uniquely identifies an entry in the s5AgTrapFilterTable.
OBJECT-TYPE    
  INTEGER  

s5AgTrapFilterTrapOID 1.3.6.1.4.1.45.1.6.4.2.11.1.2
The OID of the trap. This variable is requried for row creation.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

s5AgTrapFilterTrapInitiator1 1.3.6.1.4.1.45.1.6.4.2.11.1.3
A value that determines the first condition for filtering a trap.This entry is the value of the first varbind for a particular trap in most cases. We need to specify every initiator that represents the corresponding trap variable for each trap. If the value of this initiator is 0 (wildcard or don't care), it means that it can represent all possible values for this initiator. The trap-filter design and functional spec. provides a more detailed explanation on this subject.
OBJECT-TYPE    
  INTEGER  

s5AgTrapFilterTrapInitiator2 1.3.6.1.4.1.45.1.6.4.2.11.1.4
A value that determines the second condition for filtering a trap. This entry is the value of the second varbind for most traps. If the value of this initiator is 0 (wildcard or don't care), it means that it can represent all possible values for this initiator. If a trap has only one varbind, this entry should be set to 0.
OBJECT-TYPE    
  INTEGER  

s5AgTrapFilterTrapInitiator3 1.3.6.1.4.1.45.1.6.4.2.11.1.5
A value that determines the third condition for filtering a trap. This entry is the value of the third varbind for most traps. If the value of this initiator is 0(wildcard or don't care), it means that it can represent all possible values for this initiator. If a trap has only one or two varbinds, this entry should be set to 0.
OBJECT-TYPE    
  INTEGER  

s5AgTrapFilterStatus 1.3.6.1.4.1.45.1.6.4.2.11.1.6
Indicates whether this trap is enabled or not. enabled(1) indicates that if this type of event occurs, a trap that is generated will be queued for transmit. disabled(2) indicates that if this trap if generated, it will not be queued for transmit and s5AgTrapFilterDelayTime is not valid.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

s5AgTrapFilterDelayTime 1.3.6.1.4.1.45.1.6.4.2.11.1.7
The time delay period required to be met, between each consecutive occurences of this event. Traps recieved within this period will be dropped.
OBJECT-TYPE    
  INTEGER  

s5AgTrapEntryStatus 1.3.6.1.4.1.45.1.6.4.2.11.1.8
A manager is restricted to change the state of an entry base on the following table: create under To: valid Request Creation invalid From: valid OK NO OK OK createRequest N/A N/A N/A N/A underCreation OK NO OK OK invalid NO NO NO OK nonExistent NO OK NO OK In the table above, it is not applicable to change the state from createRequest to any other states. When the status of a table entry is set to the value of invalid(4), the entry will be removed from the table. If an entry has been in the underCreation(3) state for more than 10 minutes, it will be set to invalid(4) and subsequently removed from the table. This variable is requried for row creation.
OBJECT-TYPE    
  INTEGER valid(1), createRequest(2), underCreation(3), invalid(4)  

s5AgTrapFilterGlobalStatus 1.3.6.1.4.1.45.1.6.4.2.12
This value is the status of all the traps that supported by this trap-filter system. If the value is 1 (enable all) , all traps in the system are enabled. If the value is 2 (disable all), all traps in the system are disabled. If the value is 3 (enable-all-and-use-table) all traps are enabled except for traps that are disabled in the s5AgTrapFilterTable are disabled. If the value is 4 (disable-all-and-use-table) all traps are disabled except for traps that are enabled in the s5AgTrapFilterTable are enabled.
OBJECT-TYPE    
  INTEGER enable-all(1), disable-all(2), enable-all-and-use-table(3), disable-all-and-use-table(4)  

s5AgentMgmt 1.3.6.1.4.1.45.1.6.4.3
OBJECT IDENTIFIER    

s5AgTrpRcvrMaxEnt 1.3.6.1.4.1.45.1.6.4.3.1
The maximum number of rows in the trap receiver table.
OBJECT-TYPE    
  INTEGER 0..255  

s5AgTrpRcvrCurEnt 1.3.6.1.4.1.45.1.6.4.3.2
The current number of rows in the trap receiver table.
OBJECT-TYPE    
  INTEGER 0..255  

s5AgTrpRcvrNext 1.3.6.1.4.1.45.1.6.4.3.3
The index of the next available row to be created in the trap receiver table. A value of zero means that the table is full and no more rows can be added.
OBJECT-TYPE    
  INTEGER 0..255  

s5AgTrpRcvrTable 1.3.6.1.4.1.45.1.6.4.3.4
A table of managers which to send traps.
OBJECT-TYPE    
  SEQUENCE OF  
    S5AgTrpRcvrEntry

s5AgTrpRcvrEntry 1.3.6.1.4.1.45.1.6.4.3.4.1
A row in the trap receiver table. The column s5AgTrpRcvrStatus is used to create and delete rows in the table. Creation requires a SET PDU with objects s5AgTrpRcvrStatus, s5AgTrpRcvrAddrType, s5AgTrpRcvrNetAddr, and s5AgTrpRcvrComm for the new row.
OBJECT-TYPE    
  S5AgTrpRcvrEntry  

s5AgTrpRcvrIndx 1.3.6.1.4.1.45.1.6.4.3.4.1.1
The index of the row in the table.
OBJECT-TYPE    
  INTEGER 1..255  

s5AgTrpRcvrStatus 1.3.6.1.4.1.45.1.6.4.3.4.1.2
This object is used to create and delete rows in the table and control if they are used. The values that can be written are: valid(2)....makes an existing row valid - can only be written to change the value from ignore(3) ignore(3)...don't use this entry to send traps to at this time delete(4)...deletes the row create(5)...creates a new row - only value that can be used to create a row in the table If the row exists, then a SET with value of create(5) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: other(1)....some other case valid(2)....the row exists and is valid ignore(3)...don't use this entry to send traps to at this time
OBJECT-TYPE    
  INTEGER other(1), valid(2), ignore(3), delete(4), create(5)  

s5AgTrpRcvrAddrType 1.3.6.1.4.1.45.1.6.4.3.4.1.3
The type of address that is stored in the object s5AgTrpRcvrNetAddr. The value is: ip(1)....IP address ipx(2)...IPX address. Note: When changing the value of this object with an SNMP SET request, the SET PDU must also specify a value for the s5AgTrpRcvrNetAddr object.
OBJECT-TYPE    
  INTEGER ip(1), ipx(2)  

s5AgTrpRcvrNetAddr 1.3.6.1.4.1.45.1.6.4.3.4.1.4
The network address (in network order) for SNMP manager that is to receive the trap.
OBJECT-TYPE    
  OCTET STRING  

s5AgTrpRcvrComm 1.3.6.1.4.1.45.1.6.4.3.4.1.5
Community string to use.
OBJECT-TYPE    
  OCTET STRING SIZE(0..32)  

s5AgTrpRcvrAgeTime 1.3.6.1.4.1.45.1.6.4.3.4.1.6
The time interval used to age entries out of the trap receiver table. The default value if not specified will be 0, or infinite, never to be aged out.
OBJECT-TYPE    
  TimeIntervalSec  

s5AgRemoteLoginMgmt 1.3.6.1.4.1.45.1.6.4.3.5
OBJECT IDENTIFIER    

s5AgRemoteLoginIp 1.3.6.1.4.1.45.1.6.4.3.5.1
This value indicates the last IP address remote login to this system.
OBJECT-TYPE    
  IpAddress  

s5AgRemoteLoginStatus 1.3.6.1.4.1.45.1.6.4.3.5.2
This value indicates the status of remote login to this system.
OBJECT-TYPE    
  INTEGER statusUnknown(1), successful(2), passwordFail(3), loginTimeout(4), loginInactivityTimeout(5), telnetSessionExisted(6), nonAllowedIPaddr(7), localConsoleBusy(8), excessiveLoginFail(9), accessPermissionOff(10), loginLogout(11)  

s5AgentSystem 1.3.6.1.4.1.45.1.6.4.4
OBJECT IDENTIFIER    

s5AgSysAutoPvid 1.3.6.1.4.1.45.1.6.4.4.1
This value indicates whether adding a port as a member of a VLAN automatically results in its PVID being set to be the same as that VLAN ID. Some exceptions apply.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

s5AgSysCurrentOperationalMode 1.3.6.1.4.1.45.1.6.4.4.2
Indicates the stacking mode. Pure stack mode does not allow BS450 and BS410 units to join stack and provides some advanced features that are not available in Hybrid stack mode.
OBJECT-TYPE    
  INTEGER pure(1), hybrid(2)  

s5AgSysNextBootOperationalMode 1.3.6.1.4.1.45.1.6.4.4.3
Indicates the stacking mode at the next boot. A change to this object will modify the stacking mode after the system is reset/rebooted.
OBJECT-TYPE    
  INTEGER pure(1), hybrid(2)  

s5AgSysBinaryConfigFilename 1.3.6.1.4.1.45.1.6.4.4.4
Name of the binary configuration file that will be downloaded/uploaded when the s5AgInfoFileAction object is set to dnldConfig(2) or upldConfig(4). When not used, the value is a zero length string.
OBJECT-TYPE    
  DisplayString SIZE(0..128)  

s5AgSysTftpServerAddress 1.3.6.1.4.1.45.1.6.4.4.5
The IP address of the TFTP server for all TFTP operations. If not used, then the value is 0.0.0.0
OBJECT-TYPE    
  IpAddress  

s5AgSysAsciiConfigFilename 1.3.6.1.4.1.45.1.6.4.4.6
Name of the ascii configuration file that will be downloaded/uploaded either at boot time when the s5AgSysAsciiConfigAutoDownload object is set to useConfig(3), or when the s5AgSysAsciiConfigDownloadStatus object is set to startDownload(4). When not used, the value is a zero length string.
OBJECT-TYPE    
  DisplayString SIZE(0..128)  

s5AgSysAsciiConfigAutoDownload 1.3.6.1.4.1.45.1.6.4.4.7
Indicates whether an ASCII configuration file should be downloaded at boot time. The file can be downloaded using either the configured filename and TFTP server address, or a BOOTP server can be used to determine the filename and TFTP server address.
OBJECT-TYPE    
  INTEGER disabled(1), useBootp(2), useConfig(3)  

s5AgSysAsciiConfigAutoDldStatus 1.3.6.1.4.1.45.1.6.4.4.8
Indicates the status of the last automatic ASCII configuration file download at boot time. If no automatic download at boot time has been attempted, the value returned will be failed(3).
OBJECT-TYPE    
  INTEGER passed(1), inProgress(2), failed(3)  

s5AgSysAsciiConfigManualDownload 1.3.6.1.4.1.45.1.6.4.4.9
Indicates the status of the last manual attempt to download an ASCII configuration file. The value of this object when retrieved can be either passed(1), inProgress(2) or failed(3). Setting this object to downloadNow(4) will initiate a manual ASCII configuration file download. If no attempt has been made to manually download a configuration file, the value returned will be failed(3).
OBJECT-TYPE    
  INTEGER passed(1), inProgress(2), failed(3), downloadNow(4)  

s5AgSysCpuIpAddress 1.3.6.1.4.1.45.1.6.4.4.10
The system's CPU IP address. Note that for a stackable system in standalone mode, this will be the standalone IP address, but in stack mode, this will be the stack IP address. I.e., this is always the IP address at which the system is reachable. Setting this object will modify the corresponding IP address.
OBJECT-TYPE    
  IpAddress  

s5AgSysStackIpAddress 1.3.6.1.4.1.45.1.6.4.4.11
The stack IP address of a stackable system. A non-stackable system should never return an instance of this object, nor allow writes to this object. Note that in standalone mode, this will still be the stack IP address, even though it is not in use. When in stack mode, the IP address of individual units can be found in the s5ChasComTable in the s5Chassis MIB (and note that these addresses will not be in use when in stack mode).
OBJECT-TYPE    
  IpAddress  

s5AgSysCpuNetMask 1.3.6.1.4.1.45.1.6.4.4.12
The system's CPU subnet mask.
OBJECT-TYPE    
  IpAddress  

s5AgSysManagementVlanId 1.3.6.1.4.1.45.1.6.4.4.13
The VLAN ID of the system's management VLAN.
OBJECT-TYPE    
  INTEGER 1..4094  

Defined Objects

S5AgMyIfEntry  
SEQUENCE    
  INTEGER as s5AgMyIfIndx  
  IpAddress as s5AgMyIfNxtBootIpAddr  
  IpAddress as s5AgMyIfNxtBootNetMask  
  DisplayString as s5AgMyIfCfgFname  
  IpAddress as s5AgMyIfLdSvrAddr  
  DisplayString as s5AgMyIfImgFname  
  INTEGER as s5AgMyIfValidFlag  
  IpxAddress as s5AgMyIfNxtBootIpxAddr  
  IpAddress as s5AgMyIfBootRouterAddr  
  MacAddress as s5AgMyIfMacAddr  

S5AgOthIfEntry  
SEQUENCE    
  INTEGER as s5AgOthIfGrpIndx  
  INTEGER as s5AgOthIfComIndx  
  INTEGER as s5AgOthIfIndx  
  IpAddress as s5AgOthIfIpAddr  
  IpxAddress as s5AgOthIfIpxAddr  

S5AgDataCollectEntry  
SEQUENCE    
  INTEGER as s5AgDataCollectIfIndex  
  TimeTicks as s5AgDataCollectSnTimeStamp  
  INTEGER as s5AgDataCollectNetworkAddrStatus  

S5AgTrapFilterEntry  
SEQUENCE    
  INTEGER as s5AgTrapFilterIndex  
  OBJECT IDENTIFIER as s5AgTrapFilterTrapOID  
  INTEGER as s5AgTrapFilterTrapInitiator1  
  INTEGER as s5AgTrapFilterTrapInitiator2  
  INTEGER as s5AgTrapFilterTrapInitiator3  
  INTEGER as s5AgTrapFilterStatus  
  INTEGER as s5AgTrapFilterDelayTime  
  INTEGER as s5AgTrapEntryStatus  

S5AgTrpRcvrEntry  
SEQUENCE    
  INTEGER as s5AgTrpRcvrIndx  
  INTEGER as s5AgTrpRcvrStatus  
  INTEGER as s5AgTrpRcvrAddrType  
  OCTET STRING as s5AgTrpRcvrNetAddr  
  OCTET STRING as s5AgTrpRcvrComm  
  TimeIntervalSec as s5AgTrpRcvrAgeTime