S5-ETH-MULTISEG-TOPOLOGY-MIB

File: S5-ETH-MULTISEG-TOPOLOGY-MIB.mib (20382 bytes)

Imported modules

RFC1155-SMI RFC-1212 SYNOPTICS-ROOT-MIB
S5-ROOT-MIB SNMPv2-TC

Imported symbols

IpAddress TimeTicks OBJECT-TYPE
SnpxChassisType SnpxBackplaneType s5EnMsTop
MacAddress

Defined Objects

s5EnMsTopInfo 1.3.6.1.4.1.45.1.6.13.1
OBJECT IDENTIFIER    

s5EnMsTopIpAddr 1.3.6.1.4.1.45.1.6.13.1.1
An IP address of the agent. This is used to fill in the IP address field of transmitted SONMP packets. The agent should be reachable through this IP address.
OBJECT-TYPE    
  IpAddress  

s5EnMsTopStatus 1.3.6.1.4.1.45.1.6.13.1.2
Indicates if the agent is participating in multi-segment topology. The values are: topOn(1)....topology is on topOff(2)...topology is off When the value is topOff(2) the status of topology table entries is undefined. However, the agent should make its best attempt when the value is changed to topOff(2) to remove all existing instances of topology MIB objects. The agent must save the setting of this object in nonvolatile memory (i.e., save across reboots).
OBJECT-TYPE    
  INTEGER topOn(1), topOff(2)  

s5EnMsTopNmmLstChg 1.3.6.1.4.1.45.1.6.13.1.3
The value of sysUpTime the last time an entry in the NMM topology table was added, deleted, or modified. If the NMM topology table has not changed since cold/warm start of the agent, then the value is zero.
OBJECT-TYPE    
  TimeTicks  

s5EnMsTopBdgLstChg 1.3.6.1.4.1.45.1.6.13.1.4
The value of sysUpTime the last time an entry in the bridge topology table was added, deleted, or modified. If the bridge topology table has not changed since cold/warm start of the agent, then the value is zero.
OBJECT-TYPE    
  TimeTicks  

s5EnMsTopNmmMaxNum 1.3.6.1.4.1.45.1.6.13.1.5
The maximum number of entries in the NMM topology table.
OBJECT-TYPE    
  INTEGER 0..65535  

s5EnMsTopNmmCurNum 1.3.6.1.4.1.45.1.6.13.1.6
The current number of entries in the NMM topology table.
OBJECT-TYPE    
  INTEGER 0..65535  

s5EnMsTopBdgMaxNum 1.3.6.1.4.1.45.1.6.13.1.7
The maximum number of entries in the bridge topology table.
OBJECT-TYPE    
  INTEGER 0..65535  

s5EnMsTopBdgCurNum 1.3.6.1.4.1.45.1.6.13.1.8
The current number of entries in the bridge topology table.
OBJECT-TYPE    
  INTEGER 0..65535  

s5EnMsTopNmm 1.3.6.1.4.1.45.1.6.13.2
OBJECT IDENTIFIER    

s5EnMsTopNmmTable 1.3.6.1.4.1.45.1.6.13.2.1
A table of topology information from each topology agent that sends out NMM topology messages, and that has been heard by the reporting topology agent. The number of entries is determined by the number of distinct topology messages received. A topology message is identified by a combination of the IP address and segment-identifier contained in the message, and the slot-port on which it is received. Entries in the table are created by reception of a 'new' NMM topology message. An entry is removed from the table after no messages are received from the corresponding topology agent in the required time interval. NOTE: there is an entry for the reporting agent with the values of slot and port set to zero.
OBJECT-TYPE    
  SEQUENCE OF  
    S5EnMsTopNmmEntry

s5EnMsTopNmmEntry 1.3.6.1.4.1.45.1.6.13.2.1.1
A row in the NMM topology table. Entries in the table can not be created or deleted via SNMP.
OBJECT-TYPE    
  S5EnMsTopNmmEntry  

s5EnMsTopNmmSlot 1.3.6.1.4.1.45.1.6.13.2.1.1.1
The slot on which the topology message was received. NOTE: There is an artificial 'row' for the reporting agent with slot and port equal to zero. NOTE: Non-modular devices that do not have multiple slots should set this value to 1.
OBJECT-TYPE    
  INTEGER 0..255  

s5EnMsTopNmmPort 1.3.6.1.4.1.45.1.6.13.2.1.1.2
The port on which the topology message was received. NOTE: there is an artificial 'row' for the reporting agent with slot and port equal to zero.
OBJECT-TYPE    
  INTEGER 0..255  

s5EnMsTopNmmIpAddr 1.3.6.1.4.1.45.1.6.13.2.1.1.3
The IP address of the sender of the topology message.
OBJECT-TYPE    
  IpAddress  

s5EnMsTopNmmSegId 1.3.6.1.4.1.45.1.6.13.2.1.1.4
The 'segment identifier' of the segment from which the remote agent sent the topology message. The value is extracted from the received topology message. Different devices may use different methods for representing the segment identifier. For example, system 5000 NMMs that run multi-segment autotopology use the SrcIndx of the segment as the segment identifier; switches use a computed a value equal to '(256 * s) + p' where 's' is the board, card or slot number and 'p' is the port number on and as seen by the switch sending the topology message; system 3000 NMMs use the lower three bytes of the MAC address of the NMM as the segment identifier. In any case, the 'segment identifier' uniquely identifies the network segment in the remote device from which the topology message was sent.
OBJECT-TYPE    
  INTEGER 0..'FFFFFF'H  

s5EnMsTopNmmMacAddr 1.3.6.1.4.1.45.1.6.13.2.1.1.5
The MAC address of the sender of the topology message.
OBJECT-TYPE    
  MacAddress  

s5EnMsTopNmmChassisType 1.3.6.1.4.1.45.1.6.13.2.1.1.6
The chassis type of the device that sent the topology message.
OBJECT-TYPE    
  SnpxChassisType  

s5EnMsTopNmmBkplType 1.3.6.1.4.1.45.1.6.13.2.1.1.7
The backplane type of the device that sent the topology message.
OBJECT-TYPE    
  SnpxBackplaneType  

s5EnMsTopNmmLocalSeg 1.3.6.1.4.1.45.1.6.13.2.1.1.8
Indicates if the sender of the topology message is on the same Ethernet segment (i.e., NOT across a bridge) as the reporting agent.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

s5EnMsTopNmmCurState 1.3.6.1.4.1.45.1.6.13.2.1.1.9
The current state of sender of the topology message. The values are: topChanged(1)...topology information has recently changed heartbeat(2)....topology information unchanged new(3)..........sending agent is in new state.
OBJECT-TYPE    
  INTEGER topChanged(1), heartbeat(2), new(3)  

s5EnMsTopNmmEosSize 1.3.6.1.4.1.45.1.6.13.2.2
The current size of a 'row' in the table s5EnMsTopNmmEosTable. This allows applications to be able to break apart 'rows' in the table.
OBJECT-TYPE    
  INTEGER 0..1440  

s5EnMsTopNmmEosTable 1.3.6.1.4.1.45.1.6.13.2.3
A table of encoded octet strings of entries in table s5EnMsTopNmmTable. The number of entries is determined by packing of 'rows' from s5EnMsTopNmmTable.
OBJECT-TYPE    
  SEQUENCE OF  
    S5EnMsTopNmmEosEntry

s5EnMsTopNmmEosEntry 1.3.6.1.4.1.45.1.6.13.2.3.1
A row in the table of encoded octet strings for table s5EnMsTopNmmTable. Instance returned in Response PDU: On GETs: instance specified is the instance returned. On GET-NEXTs: instance returned is the instance of the last record contained in the octet string. Entries in the table can not be created or deleted via SNMP.
OBJECT-TYPE    
  S5EnMsTopNmmEosEntry  

s5EnMsTopNmmEos 1.3.6.1.4.1.45.1.6.13.2.3.1.1
An encoded octet string. On reads it contains an integral number of 'rows' from table s5EnMsTopNmmTable. All 'rows' are the same size which is defined by object s5EnMsTopNmmEosSize.
OBJECT-TYPE    
  OCTET STRING SIZE(0..1400)  

s5EnMsTopBdg 1.3.6.1.4.1.45.1.6.13.3
OBJECT IDENTIFIER    

s5EnMsTopBdgTable 1.3.6.1.4.1.45.1.6.13.3.1
A table of topology information from each Bridge in the network that is sending bridge topology messages that have been heard by the reporting agent. The number of entries is determined by the number of detected (and active) bridges. Entries in the table are created by reception of a topology message from a 'new' bridge. An entry is removed from the table after no messages are received from the corresponding bridge in the required time interval.
OBJECT-TYPE    
  SEQUENCE OF  
    S5EnMsTopBdgEntry

s5EnMsTopBdgEntry 1.3.6.1.4.1.45.1.6.13.3.1.1
A row in the bridge topology table. Entries in the table can not be created or deleted via SNMP.
OBJECT-TYPE    
  S5EnMsTopBdgEntry  

s5EnMsTopBdgSlotNum 1.3.6.1.4.1.45.1.6.13.3.1.1.1
The slot on which the topology message was received. NOTE: Non-modular devices that do not have multiple slots should set this value to 1.
OBJECT-TYPE    
  INTEGER 0..255  

s5EnMsTopBdgPortNum 1.3.6.1.4.1.45.1.6.13.3.1.1.2
The port on which the topology message was received.
OBJECT-TYPE    
  INTEGER 0..255  

s5EnMsTopBdgIpAddr 1.3.6.1.4.1.45.1.6.13.3.1.1.3
The IP address of the bridge that sent the topology message.
OBJECT-TYPE    
  IpAddress  

s5EnMsTopBdgNumber 1.3.6.1.4.1.45.1.6.13.3.1.1.4
The 'Bridge Number' of the bridge that sent the topology message. This is the IEEE 802.1 bridge number.
OBJECT-TYPE    
  INTEGER 0..65535  

s5EnMsTopBdgMacAddr 1.3.6.1.4.1.45.1.6.13.3.1.1.5
The MAC Address of the bridge that sent the topology message.
OBJECT-TYPE    
  MacAddress  

s5EnMsTopBdgType 1.3.6.1.4.1.45.1.6.13.3.1.1.6
The 'kind of bridge' that sent the topology message. The values are: other(1).....unknown or other type locSyn(2)....local SynOptics bridge remSyn(3)....remote SynOptics bridge kalpana(4)...Kalpana bridge(switch)
OBJECT-TYPE    
  INTEGER other(1), localSyn(2), remoteSyn(3), kalpana(4)  

s5EnMsTopBdgNumPorts 1.3.6.1.4.1.45.1.6.13.3.1.1.7
The number of ports on the bridge.
OBJECT-TYPE    
  INTEGER  

s5EnMsTopBdgStatus 1.3.6.1.4.1.45.1.6.13.3.1.1.8
The current operational status from the bridge that sent the topology message. The values are: other(1).....unknown or other active(2)....bridge is active standby(3)...bridge is in standby A value of standby(3) means that at least ONE port is in standby mode. A value of active(2) means NO port is in standby mode.
OBJECT-TYPE    
  INTEGER other(1), active(2), standby(3)  

s5EnMsTopBdgHelloPortNum 1.3.6.1.4.1.45.1.6.13.3.1.1.9
The port number used by the bridge to send the topology message. This port may or may not be in standby mode.
OBJECT-TYPE    
  INTEGER 0..255  

s5EnMsTopBdgHelloPortType 1.3.6.1.4.1.45.1.6.13.3.1.1.10
The type of the port used by the bridge to send the topology message. The values are: other(1)...other or unknown type eth(2).....ethernet tok4(3)....4 Mbit token ring tok16(4)...16 Mbit token ring fddi(5)....fddi t1(6)......t1 Note: These enumerations were done for 'completeness'. No other value than eth(2) should ever be received by an ethernet agent.
OBJECT-TYPE    
  INTEGER other(1), eth(2), tok4(3), tok16(4), fddi(5), t1(6)  

s5EnMsTopBdgHelloPortStatus 1.3.6.1.4.1.45.1.6.13.3.1.1.11
The status of the port used by the bridge to send the topology message. The values are: other(1).....unknown or other active(2)....port is active standby(3)...port is in standby
OBJECT-TYPE    
  INTEGER other(1), active(2), standby(3)  

s5EnMsTopBdgCompBdgMac1 1.3.6.1.4.1.45.1.6.13.3.1.1.12
The first MAC address of a companion bridge of the bridge that sent the topology message. The value is 00:00:00:00:00:00 for local bridges (since there is no companion bridge) and also when the companion MAC address is unknown for remote bridges.
OBJECT-TYPE    
  MacAddress  

s5EnMsTopBdgCompBdgMac2 1.3.6.1.4.1.45.1.6.13.3.1.1.13
The second MAC address of a companion bridge of the bridge that sent the topology message. The value is 00:00:00:00:00:00 for local bridges (since there is no companion bridge) and also when the companion MAC address is unknown for remote bridges.
OBJECT-TYPE    
  MacAddress  

s5EnMsTopBdgEosSize 1.3.6.1.4.1.45.1.6.13.3.2
The current size of a 'row' in the table s5EnMsTopBdgEosTable. This allows applications to be able to break apart 'rows' in the table.
OBJECT-TYPE    
  INTEGER 0..1440  

s5EnMsTopBdgEosTable 1.3.6.1.4.1.45.1.6.13.3.3
A table of encoded octet strings of entries in table s5EnMsTopBdgTable. The number of entries is determined by packing of 'rows' from s5EnMsTopBdgTable.
OBJECT-TYPE    
  SEQUENCE OF  
    S5EnMsTopBdgEosEntry

s5EnMsTopBdgEosEntry 1.3.6.1.4.1.45.1.6.13.3.3.1
A row in the table of encoded octet strings for table s5EnMsTopBdgTable. Instance returned in Response PDU: On GETs: instance specified is the instance returned. On GET-NEXTs: instance returned is the instance of the last record contained in the octet string. Entries in the table can not be created or deleted via SNMP.
OBJECT-TYPE    
  S5EnMsTopBdgEosEntry  

s5EnMsTopBdgEos 1.3.6.1.4.1.45.1.6.13.3.3.1.1
An encoded octet string. On reads it contains an integral number of 'rows' from table s5EnMsTopBdgTable. All 'rows' are the same size which is defined by object s5EnMsTopBdgEosSize.
OBJECT-TYPE    
  OCTET STRING SIZE(0..1400)  

s5EnMsTopSrcMac 1.3.6.1.4.1.45.1.6.13.4
OBJECT IDENTIFIER    

s5EnMsTopSrcMacAddrTable 1.3.6.1.4.1.45.1.6.13.4.1
A table describing the source MAC addresses that the agent uses to transmit topology messages on different segments in the device. The MAC addresses are preallocated and remain unchanged for the agent. However, the mapping between a MAC address and segment may change, since it can depend on the current physical and/or logical configuration of the device. Implementation of this group is required for those devices that use different source MAC addresses to transmit topology messages on different segments. Implementation of this group is optional otherwise.
OBJECT-TYPE    
  SEQUENCE OF  
    S5EnMsTopSrcMacAddrEntry

s5EnMsTopSrcMacAddrEntry 1.3.6.1.4.1.45.1.6.13.4.1.1
A row in the table of MAC address-to-segment mappings. Entries in the table can not be created or deleted via SNMP.
OBJECT-TYPE    
  S5EnMsTopSrcMacAddrEntry  

s5EnMsTopSrcMacAddr 1.3.6.1.4.1.45.1.6.13.4.1.1.1
The MAC address used to transmit topology messages.
OBJECT-TYPE    
  MacAddress  

s5EnMsTopSrcMacSegId 1.3.6.1.4.1.45.1.6.13.4.1.1.2
The 'segment-identifier' of the segment on which topology messages were transmitted.
OBJECT-TYPE    
  INTEGER 0..16777215  

s5EnMsTopSrcMacAddrLstChg 1.3.6.1.4.1.45.1.6.13.4.2
The value of sysUpTime when an entry in the table s5EnMsTopSrcMacAddrTable was last changed. If no changes have been done since cold/warm start of the agent, then the value is zero.
OBJECT-TYPE    
  TimeTicks  

Defined Objects

S5EnMsTopNmmEntry  
SEQUENCE    
  INTEGER as s5EnMsTopNmmSlot  
  INTEGER as s5EnMsTopNmmPort  
  IpAddress as s5EnMsTopNmmIpAddr  
  INTEGER as s5EnMsTopNmmSegId  
  MacAddress as s5EnMsTopNmmMacAddr  
  SnpxChassisType as s5EnMsTopNmmChassisType  
  SnpxBackplaneType as s5EnMsTopNmmBkplType  
  INTEGER as s5EnMsTopNmmLocalSeg  
  INTEGER as s5EnMsTopNmmCurState  

S5EnMsTopNmmEosEntry  
SEQUENCE    
  OCTET STRING as s5EnMsTopNmmEos  

S5EnMsTopBdgEntry  
SEQUENCE    
  INTEGER as s5EnMsTopBdgSlotNum  
  INTEGER as s5EnMsTopBdgPortNum  
  IpAddress as s5EnMsTopBdgIpAddr  
  INTEGER as s5EnMsTopBdgNumber  
  MacAddress as s5EnMsTopBdgMacAddr  
  INTEGER as s5EnMsTopBdgType  
  INTEGER as s5EnMsTopBdgStatus  
  INTEGER as s5EnMsTopBdgNumPorts  
  INTEGER as s5EnMsTopBdgHelloPortNum  
  INTEGER as s5EnMsTopBdgHelloPortType  
  INTEGER as s5EnMsTopBdgHelloPortStatus  
  MacAddress as s5EnMsTopBdgCompBdgMac1  
  MacAddress as s5EnMsTopBdgCompBdgMac2  

S5EnMsTopBdgEosEntry  
SEQUENCE    
  OCTET STRING as s5EnMsTopBdgEos  

S5EnMsTopSrcMacAddrEntry  
SEQUENCE    
  MacAddress as s5EnMsTopSrcMacAddr  
  INTEGER as s5EnMsTopSrcMacSegId