S5-ETHERNET-COMMON-MIB

File: S5-ETHERNET-COMMON-MIB.mib (26525 bytes)

Imported modules

RFC1155-SMI RFC-1212 S5-ETHERNET-MIB
S5-TCS-MIB

Imported symbols

Counter OBJECT-TYPE s5EnCfg
s5EnStat TimeIntervalSec SrcIndx
AttId

Defined Objects

s5EnPortTable 1.3.6.1.4.1.45.1.6.6.1.1
A table containing information about each managed ethernet connectivity port on a board. The number of entries is determined by the number of managed ports. Those boards that do not have any ports do not have any entries in this table.
OBJECT-TYPE    
  SEQUENCE OF  
    S5EnPortEntry

s5EnPortEntry 1.3.6.1.4.1.45.1.6.6.1.1.1
A row in Ethernet port table. Entries can not be created or deleted via SNMP.
OBJECT-TYPE    
  S5EnPortEntry  

s5EnPortBrdIndx 1.3.6.1.4.1.45.1.6.6.1.1.1.1
The index of the board. This corresponds to the index of the slot containing the board.
OBJECT-TYPE    
  INTEGER 1..255  

s5EnPortIndx 1.3.6.1.4.1.45.1.6.6.1.1.1.2
The index of the port on the board. Its value ranges between 1 and index of the last manageable port on the board.
OBJECT-TYPE    
  INTEGER 1..255  

s5EnPortPartStatus 1.3.6.1.4.1.45.1.6.6.1.1.1.3
The partition status of the port. The following values can be written: enabled(2)..........enabled port partition(3)........partition port timedPartition(5)...time partition port (uses value from s5EnPortPartTime) The following values reflect the partition status of the port: other(1).............partition status unknown enabled(2)...........port enabled partition(3).........port partitioned autoPartition(4).....port auto-partitioned by hardware timedPartition(5)....port is timed partitioned (see value of s5EnPortPartTime). On GETs with port status of timedPartition(5), if the time remaining before the partition is undone is available, it will be reported in object s5EnPortPartTime as a positive value. If not available, the value of s5EnPortPartTime will be zero. When changing a port to timedPartition(5), the SET request must also contain the value for object s5EnPortPartTime. Only value partition(3) will survive resets of the host card.
OBJECT-TYPE    
  INTEGER other(1), enabled(2), partition(3), autoPartition(4), timedPartition(5)  

s5EnPortPartTime 1.3.6.1.4.1.45.1.6.6.1.1.1.4
The length of time to keep the port partitioned when a timed partition is done to the port. This object can only be written in the same request that sets s5EnPortPartStatus to timedPartition(5). Afterwards, it indicates the amount of time left before the timed partition is completed, at which time s5EnPortPartStatus is changed to enabled(2). This object has the value of zero if the port is not time partitioned, or if the amount of time is not available.
OBJECT-TYPE    
  TimeIntervalSec  

s5EnPortLinkStatus 1.3.6.1.4.1.45.1.6.6.1.1.1.5
Tells whether the port is receiving link status. The values are: other(1)...returned for AUI off(2).....link is not connected on(3)......link is connected on/off applies to 10BASE-T and Fiber ports only.
OBJECT-TYPE    
  INTEGER other(1), off(2), on(3)  

s5EnPortJabberStatus 1.3.6.1.4.1.45.1.6.6.1.1.1.6
The jabber status of the DTE(s) connected to the port. The values are: other(1).......unknown or other condition jabbering(2)...port receiving jabber ok(3)..........no jabber detected.
OBJECT-TYPE    
  INTEGER other(1), jabbering(2), ok(3)  

s5EnPortExtTable 1.3.6.1.4.1.45.1.6.6.1.3
An extension table to s5EnPortTable containing additional information about per port switchable, autonegotiating 10/100 Mbit ethernet connectivity ports on a board. The number of entries is determined by the number of managed ports. Those boards that do not have any ports do not have any entries in this table.
OBJECT-TYPE    
  SEQUENCE OF  
    S5EnPortExtEntry

s5EnPortExtEntry 1.3.6.1.4.1.45.1.6.6.1.3.1
A row in Ethernet port extension table. Entries can not be created or deleted via SNMP.
OBJECT-TYPE    
  S5EnPortExtEntry  

s5EnPortExtBrdIndx 1.3.6.1.4.1.45.1.6.6.1.3.1.1
The index of the board. This corresponds to the index of the slot containing the board.
OBJECT-TYPE    
  INTEGER 1..255  

s5EnPortExtIndx 1.3.6.1.4.1.45.1.6.6.1.3.1.2
The index of the port on the board. Its value ranges between 1 and index of the last manageable port on the board.
OBJECT-TYPE    
  INTEGER 1..255  

s5EnPortExtHwCapability 1.3.6.1.4.1.45.1.6.6.1.3.1.3
A bit array that contains the bit map representing the hardware capabilites of the port. The bit 7 tells if the port supports auto-negotiation. If the auto negotiation is on, the port will have multiple speed capabilities while if the auto negotiation is not supported, the hardware will only be capable for one speed: bit 0 - 10 BASE-T half duplex capable bit 1 - 10 BASE-T full duplex capable bit 2 - 100 BASE-TX half duplex capable bit 3 - 100 BASE-TX full duplex capable bit 5 - 100 BASE-FX full duplex capable bit 6 - 100 BASE-FX half duplex capable bit 7 - auto negotiation support capability When auto negotiation is supported only bits 0-3 are used to indicate the capabilities available for negotiation, and any or all of these bits may be set as long as at least one bit is set. When auto negotiation is NOT supported (bit 7 = 0) all other bits are used to indicate the capabilities supported by the port, but which must be manually configured.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

s5EnPortExtAutoNegAdv 1.3.6.1.4.1.45.1.6.6.1.3.1.4
A bit array that contains the bit map representing the abilities advertised during link negociation. The bit 7 tells if auto negotiation is enabled or disabled: bit 0 - 10 BASE-T half duplex capable bit 1 - 10 BASE-T full duplex capable bit 2 - 100 BASE-TX half duplex capable bit 3 - 100 BASE-TX full duplex capable bit 5 - 100 BASE-FX full duplex capable bit 6 - 100 BASE-FX half duplex capable bit 7 - auto negotiation is enabled or disabled Only capabilites present in the hardware as indicated by s5EnPortExtHwCapability can be advertised. If auto negotiation is enabled only bits 0-3 are used to indicate the capabilities available for negotiation. Any or all of these bits may be set as long as at least one bit is set, AND the settings are in accordance with s5EnPortExtHwCapability. If auto negotiation is disabled one and only one of the speed setting bits MUST be set in accordance with s5EnPortExtHwCapability.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

s5EnPortExtAutoNegRcvd 1.3.6.1.4.1.45.1.6.6.1.3.1.5
A bit array that contains the bit map representing the auto-negotiation abilities of the remote end of the link: bit 0 - 10 BASE-T half duplex capable bit 1 - 10 BASE-T full duplex capable bit 2 - 100 BASE-TX half duplex capable bit 3 - 100 BASE-TX full duplex capable
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

s5EnPortExt10MbSegAttCfg 1.3.6.1.4.1.45.1.6.6.1.3.1.6
The index for the segment used in case a 10 Mbit link is established.
OBJECT-TYPE    
  AttId  

s5EnPortExt100MbSegAttCfg 1.3.6.1.4.1.45.1.6.6.1.3.1.7
The index for the segment used in case a 100 Mbit link is established.
OBJECT-TYPE    
  AttId  

s5EnPortExt10MbSegConnCapability 1.3.6.1.4.1.45.1.6.6.1.3.1.8
A bit array that contains the bit map representing all available 10Mbit backplane segment and local segment connections for the port. One bit is also reserved to indicate if the cluster has an isolate capability. The first 31 bits of the array represent the backplane numbers, starting from the lower order bit. Bit 32 indicates whether the port has a null connection capability. The bits in the fifth and sixth octets, starting with bits in the lower order octet, represent local segments that the port can connect to. A bit with a value of 1 means that the port is capable of connecting to the corresponding backplane segment, local segment or null segment.
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

s5EnPortExt100MbSegConnCapability 1.3.6.1.4.1.45.1.6.6.1.3.1.9
A bit array that contains the bit map representing all available 100Mbit backplane segment and local segment connections for the port. One bit is also reserved to indicate if the cluster has an isolate capability. The first 31 bits of the array represent the backplane numbers, starting from the lower order bit. Bit 32 indicates whether the port has a null connection capability. The bits in the fifth and sixth octets, starting with bits in the lower order octet, represent local segments that the port can connect to. A bit with a value of 1 means that the port is capable of connecting to the corresponding backplane segment, local segment or null segment.
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

s5EnPortExtActiveSpeed 1.3.6.1.4.1.45.1.6.6.1.3.1.10
The speed of the link. The possible values are: unknown(1)........unknown, no link bps10M(2).........10 Mbit link bps100M(3)........100 Mbit link
OBJECT-TYPE    
  INTEGER unknown(1), bps10M(2), bps100M(3)  

s5EnPortExtCurDuplexMode 1.3.6.1.4.1.45.1.6.6.1.3.1.11
The status of duplex mode. The possible values are: unknown(1)........unknown, no link halfDuplex(2).........half duplex mode fullDuplex(3)........full duplex mode
OBJECT-TYPE    
  INTEGER unknown(1), halfDuplex(2), fullDuplex(3)  

s5EnBStatTable 1.3.6.1.4.1.45.1.6.6.2.1
A table containing Ethernet basic statistics. The entries in the table may come from several different data sources. The number of entries is determined by the number of sources that can provide the information.
OBJECT-TYPE    
  SEQUENCE OF  
    S5EnBStatEntry

s5EnBStatEntry 1.3.6.1.4.1.45.1.6.6.2.1.1
A row in Ethernet basic statistics table. Entries can not be created or deleted via SNMP.
OBJECT-TYPE    
  S5EnBStatEntry  

s5EnBStatSrcIndx 1.3.6.1.4.1.45.1.6.6.2.1.1.1
The index of the entry in the table. This index identifies the source of the information. Only those sources that provide these statistics are in this table.
OBJECT-TYPE    
  SrcIndx  

s5EnBStatGoodOctets 1.3.6.1.4.1.45.1.6.6.2.1.1.2
A count of octets contained in frames received which had no errors. This counter includes octets in unicast, broadcast, and multicast frames. This counter includes octets after the start frame delimiter up to FCS but not including FCS octets.
OBJECT-TYPE    
  Counter  

s5EnBStatGoodFrms 1.3.6.1.4.1.45.1.6.6.2.1.1.3
A count of frames that are detected without errors. This does not include frames received with a frame-too-long, runt, FCS, or alignment errors. This counter includes unicast, broadcast, and multicast frames.
OBJECT-TYPE    
  Counter  

s5EnBStatBcastFrms 1.3.6.1.4.1.45.1.6.6.2.1.1.4
A count of frames that are detected without errors and are directed to the broadcast group address. This does not include frames received with a frame-too-long, runt, FCS, or alignment errors. Multicast frames are not included.
OBJECT-TYPE    
  Counter  

s5EnBStatMcastFrms 1.3.6.1.4.1.45.1.6.6.2.1.1.5
A count of frames that are detected without errors and are directed to a non-broadcast group address. This does not include frames received with a frame-too-long, runt, FCS, or alignment errors.
OBJECT-TYPE    
  Counter  

s5EnBStatAlignErrors 1.3.6.1.4.1.45.1.6.6.2.1.1.6
A count of frames detected that are not an integral number of octets in length and do not pass the FCS check. This counter is incremented when the frame is received with FramingError and FcsError and whose OctetCount is greater than of equal to minFramSize and less than or equal to maxFramSize.
OBJECT-TYPE    
  Counter  

s5EnBStatFcsErrors 1.3.6.1.4.1.45.1.6.6.2.1.1.7
A count of frames detected that are an integral number of octets in length that do not pass the FCS check. This counter is incremented when the frame is received with FcsError and NoFramingError and NoCollisions and whose OctetCount is greater than or equal to minFramsize and less than or equal to maxFrameSize.
OBJECT-TYPE    
  Counter  

s5EnBStatRunts 1.3.6.1.4.1.45.1.6.6.2.1.1.8
A count of frames detected that are less than the minimum permitted frame size and have a good FCS.
OBJECT-TYPE    
  Counter  

s5EnBStatTooLongFrms 1.3.6.1.4.1.45.1.6.6.2.1.1.9
A count of frames detected that exceed the maximum permitted frame size. This counter is incremented when a frame received on this port whose OctetCount is greater than maxFramSize.
OBJECT-TYPE    
  Counter  

s5EnBStatFragments 1.3.6.1.4.1.45.1.6.6.2.1.1.10
A count of fragments detected between 80-512 bits (64 bytes), inclusively, with invalid FCS. (These commonly represent collision fragments, and are not errors).
OBJECT-TYPE    
  Counter  

s5EnBStatVeryLongEvents 1.3.6.1.4.1.45.1.6.6.2.1.1.11
A count of the times that MAU jabber lockup protection (MJLP) was detected due to transmission of data that exceeded 5 msec in duration(OctetCount greater than maxFramSize). This information can be useful in identifying faulty stations.
OBJECT-TYPE    
  Counter  

s5EnBStatColls 1.3.6.1.4.1.45.1.6.6.2.1.1.12
A count of receive collisions detected.
OBJECT-TYPE    
  Counter  

s5EnBStatLateColls 1.3.6.1.4.1.45.1.6.6.2.1.1.13
A count of late receive collisions detected. This counter is incremented for each event in which there is a receive Collision and ActivityDuration is greater than the LateEventThreshold.
OBJECT-TYPE    
  Counter  

s5EnBStatShortEvents 1.3.6.1.4.1.45.1.6.6.2.1.1.14
A count of fragments detected with ActivityDuration less than ShortEventMaxTime. ShortEventMaxTime is greater than 74 bit times and less than 82 bit times.
OBJECT-TYPE    
  Counter  

s5EnBStatRateMismatches 1.3.6.1.4.1.45.1.6.6.2.1.1.15
A count of the occurrences of out of spec bit rates. This indicates the number of times the FIFO buffer over-runs or under-runs due to transmission rate errors.
OBJECT-TYPE    
  Counter  

s5EnBStatBackOffFailures 1.3.6.1.4.1.45.1.6.6.2.1.1.16
This counter is incremented by one for each frame received on this port with collision and port activity time greater than 552 to 560 bit time.
OBJECT-TYPE    
  Counter  

s5EnBStatAutoPartitions 1.3.6.1.4.1.45.1.6.6.2.1.1.17
A count of the number of times that this port was automatically partitioned. The condition occurs when 32 consecutive collisions are detected on the port.
OBJECT-TYPE    
  Counter  

s5EnBStatShortIPGs 1.3.6.1.4.1.45.1.6.6.2.1.1.18
A count of occurrences of a too short IPG (inter packet gap before a good packet) that were detected.
OBJECT-TYPE    
  Counter  

s5EnBStatNullFrames 1.3.6.1.4.1.45.1.6.6.2.1.1.19
A count of the occurrences of frames received with no collision and whose octetCount is equal to 0 and activity time is greater than ValidPacketMinTime.
OBJECT-TYPE    
  Counter  

s5EnPStatTable 1.3.6.1.4.1.45.1.6.6.2.2
A table containing Ethernet port extension statistics. This table extends table s5EnBStatTable for ports. The entries in the table may come only from port sources. The number of entries is determined by the number of sources that can provide the information.
OBJECT-TYPE    
  SEQUENCE OF  
    S5EnPStatEntry

s5EnPStatEntry 1.3.6.1.4.1.45.1.6.6.2.2.1
A row in Ethernet port extension statistic table. Entries can not be created or deleted via SNMP.
OBJECT-TYPE    
  S5EnPStatEntry  

s5EnPStatSrcIndx 1.3.6.1.4.1.45.1.6.6.2.2.1.1
The index of the entry in the table. This index identifies the source of the information. Only those sources that provide these statistics are in this table.
OBJECT-TYPE    
  SrcIndx  

s5EnPStatSourceAddrChngs 1.3.6.1.4.1.45.1.6.6.2.2.1.2
A count of changes in Last Source Address.
OBJECT-TYPE    
  Counter  

s5EnPStatLinkStatusChngs 1.3.6.1.4.1.45.1.6.6.2.2.1.3
Contains a count of number of changes in link status from on(3) to off(2).
OBJECT-TYPE    
  Counter  

s5EnPStatLastSourceAddr 1.3.6.1.4.1.45.1.6.6.2.2.1.4
The Source Address of the last readable frame received by this port. If no frames have been received by this port since the agent began monitoring this port, the agent shall return a string of length zero.
OBJECT-TYPE    
  OCTET STRING SIZE(0..6)  

s5EnSStatTable 1.3.6.1.4.1.45.1.6.6.2.3
A table containing Ethernet Segment extension statistics. This table extends table s5EnBStatTable for segments. The entries in the table may come from several different data sources. The number of entries is determined by the number of sources that can provide the information.
OBJECT-TYPE    
  SEQUENCE OF  
    S5EnSStatEntry

s5EnSStatEntry 1.3.6.1.4.1.45.1.6.6.2.3.1
A row in Ethernet segment statistics table. Entries can not be created or deleted via SNMP.
OBJECT-TYPE    
  S5EnSStatEntry  

s5EnSStatSrcIndx 1.3.6.1.4.1.45.1.6.6.2.3.1.1
The index of the entry in the table. This index identifies the source of the information. Only those sources that provide these statistics are in this table.
OBJECT-TYPE    
  SrcIndx  

s5EnSStatSegColls 1.3.6.1.4.1.45.1.6.6.2.3.1.2
A count of number of transmit collision events(one per packet activity) for a segment (i.e., local channel or backplane network).
OBJECT-TYPE    
  Counter  

s5EnSStatSegRate 1.3.6.1.4.1.45.1.6.6.2.3.1.3
The segment speed type of this ethernet segment. The following values are currently defined: unknown (1) ------- unknown type bps10m (2) ------- 10Mbps ethernet bps100m (3) ------ 100Mbps ethernet
OBJECT-TYPE    
  INTEGER unknown(1), bps10m(2), bps100m(3)  

Defined Objects

S5EnPortEntry  
SEQUENCE    
  INTEGER as s5EnPortBrdIndx  
  INTEGER as s5EnPortIndx  
  INTEGER as s5EnPortPartStatus  
  TimeIntervalSec as s5EnPortPartTime  
  INTEGER as s5EnPortLinkStatus  
  INTEGER as s5EnPortJabberStatus  

S5EnPortExtEntry  
SEQUENCE    
  INTEGER as s5EnPortExtBrdIndx  
  INTEGER as s5EnPortExtIndx  
  OCTET STRING as s5EnPortExtHwCapability  
  OCTET STRING as s5EnPortExtAutoNegAdv  
  OCTET STRING as s5EnPortExtAutoNegRcvd  
  AttId as s5EnPortExt10MbSegAttCfg  
  AttId as s5EnPortExt100MbSegAttCfg  
  OCTET STRING as s5EnPortExt10MbSegConnCapability  
  OCTET STRING as s5EnPortExt100MbSegConnCapability  
  INTEGER as s5EnPortExtActiveSpeed  
  INTEGER as s5EnPortExtCurDuplexMode  

S5EnBStatEntry  
SEQUENCE    
  SrcIndx as s5EnBStatSrcIndx  
  Counter as s5EnBStatGoodOctets  
  Counter as s5EnBStatGoodFrms  
  Counter as s5EnBStatBcastFrms  
  Counter as s5EnBStatMcastFrms  
  Counter as s5EnBStatAlignErrors  
  Counter as s5EnBStatFcsErrors  
  Counter as s5EnBStatRunts  
  Counter as s5EnBStatTooLongFrms  
  Counter as s5EnBStatFragments  
  Counter as s5EnBStatVeryLongEvents  
  Counter as s5EnBStatColls  
  Counter as s5EnBStatLateColls  
  Counter as s5EnBStatShortEvents  
  Counter as s5EnBStatRateMismatches  
  Counter as s5EnBStatBackOffFailures  
  Counter as s5EnBStatAutoPartitions  
  Counter as s5EnBStatShortIPGs  
  Counter as s5EnBStatNullFrames  

S5EnPStatEntry  
SEQUENCE    
  SrcIndx as s5EnPStatSrcIndx  
  Counter as s5EnPStatSourceAddrChngs  
  Counter as s5EnPStatLinkStatusChngs  
  OCTET STRING as s5EnPStatLastSourceAddr  

S5EnSStatEntry  
SEQUENCE    
  SrcIndx as s5EnSStatSrcIndx  
  Counter as s5EnSStatSegColls  
  INTEGER as s5EnSStatSegRate