SANMgrV1-MIB

File: SANMgrV1-MIB.mib (134152 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
RFC-1215

Imported symbols

TimeTicks IpAddress Gauge
enterprises experimental OBJECT-TYPE
DisplayString TRAP-TYPE

Defined Objects

pathlight 1.3.6.1.4.1.2935
OBJECT IDENTIFIER    

products 1.3.6.1.4.1.2935.1
OBJECT IDENTIFIER    

sanGateway 1.3.6.1.4.1.2935.1.1
OBJECT IDENTIFIER    

sanGateway1 1.3.6.1.4.1.2935.1.1.1
OBJECT IDENTIFIER    

sanGateway2 1.3.6.1.4.1.2935.1.1.2
OBJECT IDENTIFIER    

agent 1.3.6.1.4.1.2935.2
OBJECT IDENTIFIER    

paIdentify 1.3.6.1.4.1.2935.2.1
Flash the READY light on the SAN Data Gateway front panel. A non-zero value turns the LED on for the specified number of seconds. Zero turns LED off.
OBJECT-TYPE    
  INTEGER  

paReboot 1.3.6.1.4.1.2935.2.2
Writing a reboot(2) value here causes immediate reboot.
OBJECT-TYPE    
  Reset  

paHealthCheckValue 1.3.6.1.4.1.2935.2.3
Value in percent of health check tests passed.
OBJECT-TYPE    
  Gauge  

paHealthCheckLevel 1.3.6.1.4.1.2935.2.4
Scrutiny level of health check function.
OBJECT-TYPE    
  HealthCheckLevel  

paHealthCheckInterval 1.3.6.1.4.1.2935.2.5
Health Check interval in minutes.
OBJECT-TYPE    
  Gauge  

paEvRptLevel 1.3.6.1.4.1.2935.2.6
Used when retrieving Event Log. Events with log level greater than paEvRptLevel are not retrieved.
OBJECT-TYPE    
  LogViewingLevel  

paEventLogLevels 1.3.6.1.4.1.2935.2.7
Each of 255 event types has an 8-bit level used when reading log. Currently valid LogLevel range is 0-3.
OBJECT-TYPE    
  OCTET STRING SIZE(256)  

paTrapThresholds 1.3.6.1.4.1.2935.2.8
Each of 255 event types has an 8-bit threshold. When the number of events exceeds the Trap Threshold, a trap is generated and sent to all parties listed in the trap destination table (also under SNMP control) . Threshold 0 means Never Threshold 1 means Always Threshold 2 - 255 means Number of events per 10 minute period
OBJECT-TYPE    
  OCTET STRING SIZE(256)  

paBaudRate 1.3.6.1.4.1.2935.2.9
Serial baud rate for SAN Gateway Service Port. Currently, the Agent does not support baud rate change: the rate is hard-coded to 19200 baud.
OBJECT-TYPE    
  BaudRate  

paEventLog 1.3.6.1.4.1.2935.2.10
Entry point for the Agent Event Log Table.
OBJECT-TYPE    
  SEQUENCE OF  
    LogEntry

paEventLogEntry 1.3.6.1.4.1.2935.2.10.1
OBJECT-TYPE    
  LogEntry  

paIndex 1.3.6.1.4.1.2935.2.10.1.1
MIB EventLogEntry Table index.
OBJECT-TYPE    
  INTEGER  

paTime 1.3.6.1.4.1.2935.2.10.1.2
Time stamp (since boot).
OBJECT-TYPE    
  TimeTicks  

paProducer 1.3.6.1.4.1.2935.2.10.1.3
Numeric identifier for this event's producer.
OBJECT-TYPE    
  INTEGER  

paEventClass 1.3.6.1.4.1.2935.2.10.1.4
Numeric identifier for this event's class.
OBJECT-TYPE    
  INTEGER  

paEventCode 1.3.6.1.4.1.2935.2.10.1.5
Numeric code for this event.
OBJECT-TYPE    
  INTEGER  

paSeq 1.3.6.1.4.1.2935.2.10.1.6
Sequence number (relative record number) since boot.
OBJECT-TYPE    
  INTEGER  

paEventVars 1.3.6.1.4.1.2935.2.10.1.7
Text description of event.
OBJECT-TYPE    
  DisplayString SIZE(0..256)  

paLogSize 1.3.6.1.4.1.2935.2.11
Number of records in entire event log. (Not just current records since boot.)
OBJECT-TYPE    
  Gauge  

paCommand 1.3.6.1.4.1.2935.2.12
Used for issuing command to SNMP agent.
OBJECT-TYPE    
  LogCommand  

paLogBoot 1.3.6.1.4.1.2935.2.13
Absolute index of first log entry at boot.
OBJECT-TYPE    
  Gauge  

paLogNCurrent 1.3.6.1.4.1.2935.2.14
SNMP Get (read) returns number of records since boot subject to viewing level filtering. SNMP Set (write) copies this number of records since boot (subject to level filtering) into a buffer from which records are read. This mode of use is deprecated. The preferred way to get the event log since boot is to read paLogBoot, set paEvRptLevel and do a series of SNMP GetNext calls starting at instance paLogBoot until end of event log MIB table is reached.
OBJECT-TYPE    
  Gauge  

paLogChronFirst 1.3.6.1.4.1.2935.2.15
Used to request range of records from paLogChronFirst to paLogChronLast
OBJECT-TYPE    
  Gauge  

paLogChronLast 1.3.6.1.4.1.2935.2.16
Used to request range of records from paLogChronFirst to paLogChronLast
OBJECT-TYPE    
  Gauge  

paLogScroll 1.3.6.1.4.1.2935.2.17
Used to request previous/next range of records event log
OBJECT-TYPE    
  INTEGER  

paLogFilename 1.3.6.1.4.1.2935.2.18
Used to save event log to a file.
OBJECT-TYPE    
  DisplayString SIZE(0..128)  

paEnvironmentState 1.3.6.1.4.1.2935.2.19
Temperature and Voltage Status of SAN Data Gateway: ********************************** (LSB) bit 0 Auxiliary Power bit 1 Main Power bit 2 Temperature Warning bit 3 Temperature Alarm
OBJECT-TYPE    
  INTEGER  

paGatewayFWRev 1.3.6.1.4.1.2935.2.20
SAN Data Gateway Firmware Revision information.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

paGatewayHWRev 1.3.6.1.4.1.2935.2.21
SAN Data Gateway Hardware Revision information.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

paSnmpFWRev 1.3.6.1.4.1.2935.2.22
SNMP Agent Firmware Revision information.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

paRidTag 1.3.6.1.4.1.2935.2.23
SAN Data Gateway RIDTag.
OBJECT-TYPE    
  DisplayString SIZE(0..128)  

paSerialNumber 1.3.6.1.4.1.2935.2.24
SAN Data Gateway Serial Number.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

paServerVersion 1.3.6.1.4.1.2935.2.25
Remote Management software writes Server version information here to customize SNMP Agent behavior.
OBJECT-TYPE    
  INTEGER  

paProductType 1.3.6.1.4.1.2935.2.26
Type of SAN device
OBJECT-TYPE    
  PathlightProduct  

paVPSEnabled 1.3.6.1.4.1.2935.2.27
State of ITL Access Control enable.
OBJECT-TYPE    
  Boolean  

paLicenseKey 1.3.6.1.4.1.2935.2.28
Used to pass feature enabling license keys.
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

paThirdPartyCopyEnabled 1.3.6.1.4.1.2935.2.29
State of Extended 3rd Party Copy enable. Enabled means that a valid license key has been entered for this feature.
OBJECT-TYPE    
  Boolean  

paVPSStatus 1.3.6.1.4.1.2935.2.30
State of Virtual Private SAN feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. Bit 1 is redundant with MIB var paVPSEnabled. Writing 1 to bit 0 makes VPS active if licensed. Writing 0 to bit 0 makes VPS inactive if licensed.
OBJECT-TYPE    
  INTEGER  

paThirdPartyCopyStatus 1.3.6.1.4.1.2935.2.31
State of Extended 3rd Party Copy feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. Bit 1 is redundant with MIB var paThirdPartyCopyEnabled. Writing 1 to bit 0 makes Third Party Copy active if licensed. Writing 0 to bit 0 makes Third Party Copy inactive if licensed.
OBJECT-TYPE    
  INTEGER  

paCommandControlLUN 1.3.6.1.4.1.2935.2.32
Gateway/Router Command and Control LUN
OBJECT-TYPE    
  INTEGER  

paSanDirectorEnabled 1.3.6.1.4.1.2935.2.33
State of SAN Director Support for this device. To enable, user must write a valid license key to OID paLicenseKey or enter the license key from the service port.
OBJECT-TYPE    
  Boolean  

paNodeName 1.3.6.1.4.1.2935.2.34
SAN Gateway Node Name.
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

paVPMStatus 1.3.6.1.4.1.2935.2.35
State of Virtual Private Map feature. bit 0 : active or inactive. bit 1 : licensed or not licensed.
OBJECT-TYPE    
  INTEGER  

paSRSStatus 1.3.6.1.4.1.2935.2.36
State of SAN Replication Services feature. bit 0 : active or inactive. bit 1 : licensed or not licensed.
OBJECT-TYPE    
  INTEGER  

paEthernetType 1.3.6.1.4.1.2935.2.37
Current Ethernet Speed.
OBJECT-TYPE    
  DisplayString  

paTrapSequenceNumber 1.3.6.1.4.1.2935.2.38
Sequence number of last trap sent by this SNMP Agent.
OBJECT-TYPE    
  INTEGER  

paSysNodeNameMode 1.3.6.1.4.1.2935.2.39
Algorithm used when computing Fibre Channel World Wide Node Name for each port. If the value is sameForEachPort(0), then the World Wide Node Name is the same for each port and computed based on the World Wide Node Name of the gateway. If the value is differentForEachPort(1), then the World Wide Node Name is different for each port, computed based on the World Wide Port Name for that port.
OBJECT-TYPE    
  INTEGER sameForEachPort(0), differentForEachPort(1)  

devices 1.3.6.1.4.1.2935.3
OBJECT IDENTIFIER    

pdDevices 1.3.6.1.4.1.2935.3.1
Pathlight Physical Device Group *********************************** Each device attached to the Gateway has an entry here.
OBJECT-TYPE    
  SEQUENCE OF  
    DevEntry

pdDevEntry 1.3.6.1.4.1.2935.3.1.1
OBJECT-TYPE    
  DevEntry  

pdIndex 1.3.6.1.4.1.2935.3.1.1.1
MIB table index
OBJECT-TYPE    
  INTEGER  

pdUID 1.3.6.1.4.1.2935.3.1.1.2
Universal Identifier
OBJECT-TYPE    
  DisplayString SIZE(16)  

pdType 1.3.6.1.4.1.2935.3.1.1.3
Device Type i.e. disk/tape/cd etc.
OBJECT-TYPE    
  DeviceType  

pdVendor 1.3.6.1.4.1.2935.3.1.1.4
Device Vendor
OBJECT-TYPE    
  DisplayString SIZE(8)  

pdProduct 1.3.6.1.4.1.2935.3.1.1.5
Device Product Identifier
OBJECT-TYPE    
  DisplayString SIZE(16)  

pdBlockSize 1.3.6.1.4.1.2935.3.1.1.6
Block size in Bytes
OBJECT-TYPE    
  INTEGER  

pdCapacity 1.3.6.1.4.1.2935.3.1.1.7
Capacity in BLOCKS (see pdBlockSize)
OBJECT-TYPE    
  Gauge  

pdAccess 1.3.6.1.4.1.2935.3.1.1.8
OBJECT-TYPE    
  INTEGER  

pdRemovable 1.3.6.1.4.1.2935.3.1.1.9
Is device removable ?
OBJECT-TYPE    
  Boolean  

pdStatus 1.3.6.1.4.1.2935.3.1.1.10
Device Status
OBJECT-TYPE    
  PltStatus  

pdSpeed 1.3.6.1.4.1.2935.3.1.1.11
Device Speed in MBytes/second
OBJECT-TYPE    
  INTEGER  

pdWidth 1.3.6.1.4.1.2935.3.1.1.12
Data path width in bits
OBJECT-TYPE    
  INTEGER  

pdSerial 1.3.6.1.4.1.2935.3.1.1.13
Device Serial Number
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

pdIdentify 1.3.6.1.4.1.2935.3.1.1.14
Number of seconds to flash identifying LED. Write here to flash LED on device if supported by Gateway and device. Zero turns LED off.
OBJECT-TYPE    
  INTEGER  

pdInterfaceType 1.3.6.1.4.1.2935.3.1.1.15
This device's type of communication interface.
OBJECT-TYPE    
  Interface  

pdBus 1.3.6.1.4.1.2935.3.1.1.16
SCSI bus number
OBJECT-TYPE    
  INTEGER  

pdId 1.3.6.1.4.1.2935.3.1.1.17
SCSI Address ID
OBJECT-TYPE    
  INTEGER  

pdLun 1.3.6.1.4.1.2935.3.1.1.18
SCSI Logical Unit Number.
OBJECT-TYPE    
  INTEGER  

pdCtlrIndex 1.3.6.1.4.1.2935.3.1.1.19
Index of this device's controller in the Controllers MIB table and type-specific controller tables
OBJECT-TYPE    
  INTEGER  

pdHWRev 1.3.6.1.4.1.2935.3.1.1.20
Device hardware revision number/identifier
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

pdFWRev 1.3.6.1.4.1.2935.3.1.1.21
Device firmware revision number/identifier
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

pdReset 1.3.6.1.4.1.2935.3.1.1.22
Generic device reset if supported. Write reset(1) here to reset device if supported by Gateway firmware and device.
OBJECT-TYPE    
  Reset  

pdStatusBits 1.3.6.1.4.1.2935.3.1.1.23
Device status bits as per SCSI spec.
OBJECT-TYPE    
  INTEGER  

pdScsiAnsiLevel 1.3.6.1.4.1.2935.3.1.1.24
Device SCSI level.
OBJECT-TYPE    
  ScsiAnsiLevel  

pdTargetLun 1.3.6.1.4.1.2935.3.1.1.25
This target device's Logical Unit Number as seen from attached host.
OBJECT-TYPE    
  INTEGER  

pdIpAddress 1.3.6.1.4.1.2935.3.1.1.26
This target device's IP Address if applicable. In case of SAN Gateway or Router, this information is used to allow arbitrary drill-down capability.
OBJECT-TYPE    
  IpAddress  

controllers 1.3.6.1.4.1.2935.4
OBJECT IDENTIFIER    

pcControllers 1.3.6.1.4.1.2935.4.1
Pathlight Controller Group ******************************* All controllers installed in the SAN Data Gateway have an entry here AND a parallel entry in the controller-type specific table (Fibre Channnel, SSA, or SCSI).
OBJECT-TYPE    
  SEQUENCE OF  
    CtlrEntry

pcCtlrEntry 1.3.6.1.4.1.2935.4.1.1
OBJECT-TYPE    
  CtlrEntry  

pcIndex 1.3.6.1.4.1.2935.4.1.1.1
MIB Table index.
OBJECT-TYPE    
  INTEGER  

pcType 1.3.6.1.4.1.2935.4.1.1.2
Communication Interface type.
OBJECT-TYPE    
  Interface  

pcVendorId 1.3.6.1.4.1.2935.4.1.1.3
Integer vendor ID for this controller.
OBJECT-TYPE    
  VendorIDInt  

pcProductId 1.3.6.1.4.1.2935.4.1.1.4
Vendor's integer ID for this controller.
OBJECT-TYPE    
  INTEGER  

pcRevision 1.3.6.1.4.1.2935.4.1.1.5
Revision information for this controller. See also pcHWRev and pcFWRev.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

pcSubVendor 1.3.6.1.4.1.2935.4.1.1.6
Integer sub-vendor ID for this controller.
OBJECT-TYPE    
  INTEGER  

pcSubProduct 1.3.6.1.4.1.2935.4.1.1.7
Vendor's integer sub-product ID for this controller.
OBJECT-TYPE    
  INTEGER  

pcMaxBurst 1.3.6.1.4.1.2935.4.1.1.8
Maximum burst transfer rate in MBytes/second
OBJECT-TYPE    
  INTEGER  

pcLatency 1.3.6.1.4.1.2935.4.1.1.9
Latency Timer in Clock Ticks.
OBJECT-TYPE    
  INTEGER 0..255  

pcIdentify 1.3.6.1.4.1.2935.4.1.1.10
Reserved for flashing identifying LED on device.
OBJECT-TYPE    
  INTEGER  

pcPCIBus 1.3.6.1.4.1.2935.4.1.1.11
PCI Bus number in SAN Data Gateway for this controller.
OBJECT-TYPE    
  INTEGER  

pcPCIDev 1.3.6.1.4.1.2935.4.1.1.12
PCI device number in SAN Data Gateway for this controller.
OBJECT-TYPE    
  INTEGER  

pcPCIFunc 1.3.6.1.4.1.2935.4.1.1.13
PCI Function number in SAN Data Gateway for this contoller.
OBJECT-TYPE    
  INTEGER  

pcReset 1.3.6.1.4.1.2935.4.1.1.14
Generic controller reset variable. Not supported for all controller types.
OBJECT-TYPE    
  Reset  

pcRescan 1.3.6.1.4.1.2935.4.1.1.15
Writing true(1) here causes controller to rescan its bus if rescan is supported for this controller type.
OBJECT-TYPE    
  Boolean  

pcLED 1.3.6.1.4.1.2935.4.1.1.16
Is LED on?
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

pcHWRev 1.3.6.1.4.1.2935.4.1.1.17
Hardware revision for this controller.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

pcFWRev 1.3.6.1.4.1.2935.4.1.1.18
Firmware revision for this controller
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

pcPCISlot 1.3.6.1.4.1.2935.4.1.1.19
Location of Channel Card on PCI bus
OBJECT-TYPE    
  INTEGER  

pcPMCSlot 1.3.6.1.4.1.2935.4.1.1.20
Location of Card: PMC 1, 2 or 3. 0=> Not a PMC card
OBJECT-TYPE    
  INTEGER  

pcPCIClass 1.3.6.1.4.1.2935.4.1.1.21
Device class code as per PCI specification.
OBJECT-TYPE    
  OCTET STRING SIZE(3)  

pcSplitMode 1.3.6.1.4.1.2935.4.1.1.22
Enable/Disable Split Mode for this controller.
OBJECT-TYPE    
  Boolean  

pcChannelMask 1.3.6.1.4.1.2935.4.1.1.23
Specifies access permissions for this initiator in bits 0 through 18 ************************************************* -* SCSI Channels *- Bit 0 => Is access DISALLOWED to SCSI channel 1 ? Bit 1 => Is access DISALLOWED to SCSI channel 2 ? Bit 2 => Is access DISALLOWED to SCSI channel 3 ? Bit 3 => Is access DISALLOWED to SCSI channel 4 ? -* Ultra SCSI Channels *- Bit 4 => Is access DISALLOWED to Ultra SCSI channel 1 ? Bit 5 => Is access DISALLOWED to Ultra SCSI channel 2 ? Bit 6 => Is access DISALLOWED to Ultra SCSI channel 3 ? Bit 7 => Is access DISALLOWED to Ultra SCSI channel 4 ? Bit 8 => Is access DISALLOWED to Ultra SCSI channel 5 ? Bit 9 => Is access DISALLOWED to Ultra SCSI channel 6 ? -* Fibre Channel *- Bit 10 => Is access DISALLOWED to Fibre Channel 1 ? Bit 11 => Is access DISALLOWED to Fibre Channel 2 ? Bit 12 => Is access DISALLOWED to Fibre Channel 3 ? Bit 13 => Is access DISALLOWED to Fibre Channel 4 ? Bit 14 => Is access DISALLOWED to Fibre Channel 5 ? Bit 15 => Is access DISALLOWED to Fibre Channel 6 ? -* SSA Channels *- Bit 16 => Is access DISALLOWED to SSA channel 1 ? Bit 17 => Is access DISALLOWED to SSA Channel 2 ? Bit 18 => Is access DISALLOWED to SSA Channel 3 ?
OBJECT-TYPE    
  Gauge  

pcPortHostType 1.3.6.1.4.1.2935.4.1.1.24
Host type for this port. Used if VPS is not enabled.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

pcFCCtlrs 1.3.6.1.4.1.2935.4.2
Entry point for Fibre Channel Controller Device Group ****************************************************** This table parallels the Controller Table: a Fibre Channel controller with pcIndex N in the controller table appears here as index N as well, and in general there are rows in this table which are empty.
OBJECT-TYPE    
  SEQUENCE OF  
    FcCtlrEntry

fcCtlrEntry 1.3.6.1.4.1.2935.4.2.1
OBJECT-TYPE    
  FcCtlrEntry  

fcStatus 1.3.6.1.4.1.2935.4.2.1.1
Status of the Fibre Channel Controller
OBJECT-TYPE    
  FcStatus  

fcMaxSpeed 1.3.6.1.4.1.2935.4.2.1.2
Maximum Transfer Speed in MBytes per second.
OBJECT-TYPE    
  Gauge  

fcWWID 1.3.6.1.4.1.2935.4.2.1.3
World Wide Identifier for this Fibre Channel Controller.
OBJECT-TYPE    
  DisplayString SIZE(17)  

fcFWRev 1.3.6.1.4.1.2935.4.2.1.4
Firmware revision number/identifier for this Fibre Channel Controller.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

fcHWRev 1.3.6.1.4.1.2935.4.2.1.5
Hardware revision number/identifier for this Fibre Channel Controller.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

fcLoopID 1.3.6.1.4.1.2935.4.2.1.6
Fibre Channel Loop ID. soft = -1
OBJECT-TYPE    
  INTEGER -1..127  

fcFrameSize 1.3.6.1.4.1.2935.4.2.1.7
Fibre Channel frame size.
OBJECT-TYPE    
  INTEGER  

fcPortType 1.3.6.1.4.1.2935.4.2.1.8
Fibre Channel Port Type
OBJECT-TYPE    
  FibrePort  

fcMedia 1.3.6.1.4.1.2935.4.2.1.9
Media type for this Fibre Channel Controller
OBJECT-TYPE    
  FibreMedia  

fcSerialNumber 1.3.6.1.4.1.2935.4.2.1.10
Serial Number for this Fibre Channel Controller.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

fcLoopIDMode 1.3.6.1.4.1.2935.4.2.1.11
Fibre Channel Loop ID mode (soft or hard)
OBJECT-TYPE    
  FibreLoopIDMode  

fcALPhysicalAddress 1.3.6.1.4.1.2935.4.2.1.12
Arbitrated Loop Physical Address (ALPA)
OBJECT-TYPE    
  INTEGER  

fcPortMode 1.3.6.1.4.1.2935.4.2.1.13
Fibre Channel Port Mode.
OBJECT-TYPE    
  FibrePortMode  

fcConnectionOptions 1.3.6.1.4.1.2935.4.2.1.14
Connection options for ISP2200 FC chip. Values 4 - 8 are reserved.
OBJECT-TYPE    
  FibreConnOptions  

fcCtlrChipType 1.3.6.1.4.1.2935.4.2.1.15
Type of Fibre Channel controller chip. Valid types are 2100 , 2200 for QLogic ISP2100 and ISP2200 chips.
OBJECT-TYPE    
  INTEGER  

fcTapeFeature 1.3.6.1.4.1.2935.4.2.1.16
Status of Fibre Channel Tape Specification support. true means this controller supports FC Tape false means this controller does not support FC Tape
OBJECT-TYPE    
  Boolean  

fcHardID 1.3.6.1.4.1.2935.4.2.1.17
Fibre Channel Hard ID, the preferred loop ID for this controller. Even if the controller is in Hard Loop ID mode, the actual loop ID is not guaranteed to be fcHardID.
OBJECT-TYPE    
  INTEGER -1..256  

fcCurrentSpeedSetting 1.3.6.1.4.1.2935.4.2.1.18
Speed in Gb/sec. 0: Auto, 1: 1Gb, 2: 2Gb
OBJECT-TYPE    
  INTEGER  

fcCurrentSpeed 1.3.6.1.4.1.2935.4.2.1.19
Current Speed Indicator Gb/sec.
OBJECT-TYPE    
  INTEGER  

fcFrameBufferSize 1.3.6.1.4.1.2935.4.2.1.20
Fibre Channel Frame Buffer Size
OBJECT-TYPE    
  INTEGER  

fcLinkFailureCount 1.3.6.1.4.1.2935.4.2.1.21
Fibre Channel Link Failure Count
OBJECT-TYPE    
  INTEGER  

fcLossSyncCount 1.3.6.1.4.1.2935.4.2.1.22
Fibre Channel Loss of Sync Count
OBJECT-TYPE    
  INTEGER  

fcLossSignalCount 1.3.6.1.4.1.2935.4.2.1.23
Fibre Channel Loss of Signal Count
OBJECT-TYPE    
  INTEGER  

fcProtocolErrorCount 1.3.6.1.4.1.2935.4.2.1.24
Fibre Channel Primitive Sequence Protocol Error Count
OBJECT-TYPE    
  INTEGER  

fcInvalidTxWordCount 1.3.6.1.4.1.2935.4.2.1.25
Fibre Channel Invalid Transmission Word Count
OBJECT-TYPE    
  INTEGER  

fcInvalidCRCCount 1.3.6.1.4.1.2935.4.2.1.26
Fibre Channel Invalid CRC Count
OBJECT-TYPE    
  INTEGER  

fcWWNodeName 1.3.6.1.4.1.2935.4.2.1.27
The World Wide Node Name for this Fibre Channel Controller. The Node Name for this port may computer strictly on the World Wide Node Name for the gateway, or on a per port basis which uses the World Wide Port Name (fcWWID), thus giving each port a different Node Name. See paSysNodeNameMode to get or set which algorithm is in use.
OBJECT-TYPE    
  DisplayString SIZE(17)  

pcSSACtlrs 1.3.6.1.4.1.2935.4.3
Entry point for SSA Controller Device Group **************************************************** This table parallels the Controller Table: an SSA controller with pcIndex N in the controller table appears here as row index N as well, and in general there are rows in this table which are empty.
OBJECT-TYPE    
  SEQUENCE OF  
    SSACtlrEntry

ssaCtlrEntry 1.3.6.1.4.1.2935.4.3.1
OBJECT-TYPE    
  SSACtlrEntry  

ssaStatus1 1.3.6.1.4.1.2935.4.3.1.1
Status on port 1 of dual port SSA card
OBJECT-TYPE    
  PltStatus  

ssaStatus2 1.3.6.1.4.1.2935.4.3.1.2
Status on port 2 of dual port SSA card
OBJECT-TYPE    
  PltStatus  

ssaSpeed 1.3.6.1.4.1.2935.4.3.1.3
SSA transfer speed 80 Mbytes/second or 160 MBytes/second
OBJECT-TYPE    
  SsaSpeed  

ssaUID 1.3.6.1.4.1.2935.4.3.1.4
Universal Identifier for this SSA Controller.
OBJECT-TYPE    
  DisplayString SIZE(16)  

ssaFWRev 1.3.6.1.4.1.2935.4.3.1.5
Firmware revision number/identifier for this SSA controller.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

ssaMaxTarg 1.3.6.1.4.1.2935.4.3.1.6
Maximum number of targets supported.
OBJECT-TYPE    
  Gauge  

ssaMaxInit 1.3.6.1.4.1.2935.4.3.1.7
Maximum number of initiators supported.
OBJECT-TYPE    
  Gauge  

ssaPathAlg 1.3.6.1.4.1.2935.4.3.1.8
SSA pathing algorithm.
OBJECT-TYPE    
  PathingAlgorithm  

ssaHWRev 1.3.6.1.4.1.2935.4.3.1.9
Hardware revision number/identifier for this SSA controller.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

ssaMasterPriority 1.3.6.1.4.1.2935.4.3.1.10
The SSA Master Priority of an SSA node is a number from 0 to 7. SSA initiators elect a master based on this priority. If more than one SSA node has the same priority then the node with the highest UID is elected. Pathlight SSA host adapters default to a Master Priority of 4. SAN Gateway SSA Target adapters default to a priority of 5 to ensure that the Gateway node will be master in a multi-initiator loop. This value should never be set to 7 because this is the priority used to guarantee mastership to a node that is entering Service Mode.
OBJECT-TYPE    
  INTEGER 0..7  

ssaSATAQuota 1.3.6.1.4.1.2935.4.3.1.11
The SSA SAT Quota A parameter is an 8 bit number that determines 'the maximum number of frames which can be originated from this port before the port is SATisfied and forwards the SAT character. A value of zero means that no SATs are forwarded or issued from this port.'
OBJECT-TYPE    
  INTEGER 0..255  

ssaSATBQuota 1.3.6.1.4.1.2935.4.3.1.12
The SSA SAT Quota B parameter is an 8 bit number that determines 'the maximum number of frames which this port can originate without forwarding a SAT character. A value of zero means that an infinite number of frames can be sent without being subject to SAT pacing.'
OBJECT-TYPE    
  INTEGER 0..255  

ssaSATIQuota 1.3.6.1.4.1.2935.4.3.1.13
OBJECT-TYPE    
  INTEGER 0..255  

pcSCSICtlrs 1.3.6.1.4.1.2935.4.4
Entry point for SCSI Controller Device Group **************************************************** This table parallels the Controller Table: a SCSI controller with pcIndex N in the controller table appears here as row index N as well, and in general there are rows in this table which are empty.
OBJECT-TYPE    
  SEQUENCE OF  
    SCSICtlrEntry

scsiCtlrEntry 1.3.6.1.4.1.2935.4.4.1
OBJECT-TYPE    
  SCSICtlrEntry  

scsiStatus 1.3.6.1.4.1.2935.4.4.1.1
Status for this SCSI controller.
OBJECT-TYPE    
  PltStatus  

scsiSpeed 1.3.6.1.4.1.2935.4.4.1.2
SCSI Transaction speed.
OBJECT-TYPE    
  ScsiSpeed  

scsiRole 1.3.6.1.4.1.2935.4.4.1.3
Is this a Target or Initiator ?
OBJECT-TYPE    
  ScsiRole  

scsiHostId 1.3.6.1.4.1.2935.4.4.1.4
Host ID defaults to 7.
OBJECT-TYPE    
  INTEGER 0..15  

scsiMaxSpeed 1.3.6.1.4.1.2935.4.4.1.5
Maximum Speed of this SCSI Channel.
OBJECT-TYPE    
  ScsiSpeed  

scsiTerm 1.3.6.1.4.1.2935.4.4.1.6
State of internal SCSI bus terminations, if any.
OBJECT-TYPE    
  ScsiTermination  

scsiIoCard 1.3.6.1.4.1.2935.4.4.1.7
Type of SCSI controller hardware.
OBJECT-TYPE    
  ScsiCardType  

scsiMaxIds 1.3.6.1.4.1.2935.4.4.1.8
Maximum Number of IDs for this SCSI controller.
OBJECT-TYPE    
  INTEGER  

scsiMaxLuns 1.3.6.1.4.1.2935.4.4.1.9
Maximum Number of LUNs for this SCSI controller.
OBJECT-TYPE    
  INTEGER  

scsiMaxWidth 1.3.6.1.4.1.2935.4.4.1.10
Maximum transfer width in bits.
OBJECT-TYPE    
  INTEGER  

scsiHWRev 1.3.6.1.4.1.2935.4.4.1.11
Hardware revision for this SCSI controller.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

scsiFWRev 1.3.6.1.4.1.2935.4.4.1.12
Firmware revision for this SCSI controller.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

scsiResetOnPowerUp 1.3.6.1.4.1.2935.4.4.1.13
Enables/Disables SCSI bus reset upon Gateway power-up for this SCSI controller.
OBJECT-TYPE    
  Boolean  

scsiMultiInitEnabled 1.3.6.1.4.1.2935.4.4.1.14
Enables/Disables multi-initiator support on for this SCSI controller.
OBJECT-TYPE    
  Boolean  

scsiAlternateHostId 1.3.6.1.4.1.2935.4.4.1.15
Alternate Host ID for this SCSI controller. -1 means use automatic.
OBJECT-TYPE    
  INTEGER -1..15  

notification 1.3.6.1.4.1.2935.5
OBJECT IDENTIFIER    

pnTrapDest 1.3.6.1.4.1.2935.5.1
Trap destination Group Table ****************************************** A list of IP addresses to which SNMP Traps are sent in parallel using UDP Port 162.
OBJECT-TYPE    
  SEQUENCE OF  
    TrapDestEntry

pnTrapDestEntry 1.3.6.1.4.1.2935.5.1.1
OBJECT-TYPE    
  TrapDestEntry  

pnIndex 1.3.6.1.4.1.2935.5.1.1.1
Index into TrapDest table
OBJECT-TYPE    
  INTEGER  

pnIPAddr 1.3.6.1.4.1.2935.5.1.1.2
IP Address of destination entity to which traps are sent.
OBJECT-TYPE    
  IpAddress  

pnUdpPort 1.3.6.1.4.1.2935.5.1.1.3
UDP Port on which traps are sent to this entity.
OBJECT-TYPE    
  INTEGER 0..65535  

pnTrapStyle 1.3.6.1.4.1.2935.5.1.1.4
Style to be used when building a trap PDU to be sent to this entity. A value of proprietary(1) selects the proprietary format used by the Pathlight SAN Director management application. A value of rfc1215(2) selects the format as described in the RFC 1215 TRAP-TYPE objects included in this MIB document. The default is proprietary(1).
OBJECT-TYPE    
  INTEGER proprietary(1), rfc1215(2)  

panelLED 1.3.6.1.4.1.2935.6
OBJECT IDENTIFIER    

ledReady 1.3.6.1.4.1.2935.6.1
ON/OFF state of READY LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledAuxPower 1.3.6.1.4.1.2935.6.2
ON/OFF state of AUXILIARY POWER LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledMainPower 1.3.6.1.4.1.2935.6.3
ON/OFF state of MAIN POWER LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledTempAlarm 1.3.6.1.4.1.2935.6.4
ON/OFF state of Temperature Alarm LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledTempWarn 1.3.6.1.4.1.2935.6.5
ON/OFF state of Temperature Warning LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledEtherCollision 1.3.6.1.4.1.2935.6.6
Is Ethernet Collison LED on?
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledEtherTransmit 1.3.6.1.4.1.2935.6.7
ON/OFF state of Ethernet Transmit LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  


ledScsi1 1.3.6.1.4.1.2935.6.9
ON/OFF state of SCSI Channel 1 LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledScsi2 1.3.6.1.4.1.2935.6.10
ON/OFF state of SCSI Channel 2 LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledScsi3 1.3.6.1.4.1.2935.6.11
ON/OFF state of SCSI Channel 3 LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledScsi4 1.3.6.1.4.1.2935.6.12
ON/OFF state of SCSI Channel 4 LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledActivity1 1.3.6.1.4.1.2935.6.13
ON/OFF state of Network Connection Channel 1 Activity LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledActivity2 1.3.6.1.4.1.2935.6.14
ON/OFF state of Network Connection Channel 2 Activity LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledActivity3 1.3.6.1.4.1.2935.6.15
ON/OFF state of Network Connection Channel 3 Activity LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledStatus1 1.3.6.1.4.1.2935.6.16
ON/OFF state of Network Connection Channel 1 Status LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledStatus2 1.3.6.1.4.1.2935.6.17
ON/OFF state of Network Connection Channel 2 Status LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledStatus3 1.3.6.1.4.1.2935.6.18
ON/OFF state of Network Connection Channel 1 Status LED.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledAll 1.3.6.1.4.1.2935.6.19
All LED values in one INTEGER Value *********************************************** Bit 0 Ready Bit 8 Scsi1 Bit 1 AuxPower Bit 9 Scsi2 Bit 2 MainPower Bit 10 Scsi3 Bit 3 TempAlarm Bit 11 Scsi4 Bit 4 TempWarn Bit 12 Activity1 Bit 5 EtherCollision Bit 13 Activity2 Bit 6 EtherTransmit Bit 14 Activity3 Bit 7 EtherLink Bit 15 Status1 Bit 16 Status2 Bit 17 Status3 Bit 18 Error Bit 19 Ethernet Speed
OBJECT-TYPE    
  INTEGER  

ledError 1.3.6.1.4.1.2935.6.20
Turned on to indicate an Alarm or Warning condition.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

ledEthernetSpeed 1.3.6.1.4.1.2935.6.21
ON/OFF state of Ethernet Speed indicator LED. 0 means 10 Base-T , 1 means 100 Base-T.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

paHost 1.3.6.1.4.1.2935.7
OBJECT IDENTIFIER    

hostCommand 1.3.6.1.4.1.2935.7.1
Used to issue commands to ITL control software.
OBJECT-TYPE    
  INTEGER  

hostInitiator 1.3.6.1.4.1.2935.7.2
Attached Host Group Table *************************** List of attached hosts and pertinent information.
OBJECT-TYPE    
  SEQUENCE OF  
    InitiatorEntry

hostInitiatorEntry 1.3.6.1.4.1.2935.7.2.1
OBJECT-TYPE    
  InitiatorEntry  

hostIndex 1.3.6.1.4.1.2935.7.2.1.1
Index into Host Initiator table
OBJECT-TYPE    
  INTEGER  

hostRowStatus 1.3.6.1.4.1.2935.7.2.1.2
Row Status for this row.
OBJECT-TYPE    
  INTEGER  

hostWWName 1.3.6.1.4.1.2935.7.2.1.3
World Wide name of this Initiator.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

hostName 1.3.6.1.4.1.2935.7.2.1.4
Name for this Initiator.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

hostType 1.3.6.1.4.1.2935.7.2.1.5
Operating System and other host environment information.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

hostPortID 1.3.6.1.4.1.2935.7.2.1.6
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

hostSANConnection 1.3.6.1.4.1.2935.7.2.1.7
SAN Connection (1-6) to which this host is connected.
OBJECT-TYPE    
  INTEGER  

hostConnectionType 1.3.6.1.4.1.2935.7.2.1.8
Type of SAN connection (FCAL , etc.)
OBJECT-TYPE    
  INTEGER  

hostITLData 1.3.6.1.4.1.2935.7.2.1.9
ITL Access Control data for this host. 256 possible LUNs with one Byte of data per LUN.
OBJECT-TYPE    
  OCTET STRING SIZE(256)  

hostIPAddr 1.3.6.1.4.1.2935.7.2.1.10
IP Address of this host. Host is not required to have an IP address.
OBJECT-TYPE    
  IpAddress  

scsiMap 1.3.6.1.4.1.2935.8
OBJECT IDENTIFIER    

scsiMapCommand 1.3.6.1.4.1.2935.8.1
Used to issue commands to SCSI Channel map map routines.
OBJECT-TYPE    
  INTEGER  

scsiChannelMap 1.3.6.1.4.1.2935.8.2
SCSI Channel Device Map Table ****************************** List of devices presented to SCSI attached initiator. The initiator sees a series of (Target ID , LUN ) SCSI targets which are mapped to a logical device identified by a Pathlight assigned LUN.
OBJECT-TYPE    
  SEQUENCE OF  
    ScsiMapEntry

scsiMapEntry 1.3.6.1.4.1.2935.8.2.1
OBJECT-TYPE    
  ScsiMapEntry  

scsiMapRowStatus 1.3.6.1.4.1.2935.8.2.1.1
Specifies the state of the row.
OBJECT-TYPE    
  RowStatus  

scsiMapPort 1.3.6.1.4.1.2935.8.2.1.2
SCSI port (bus) number for this entry (1 thru 10).
OBJECT-TYPE    
  INTEGER  

scsiMapTid 1.3.6.1.4.1.2935.8.2.1.3
SCSI Target ID for this entry.
OBJECT-TYPE    
  INTEGER  

scsiMapLun 1.3.6.1.4.1.2935.8.2.1.4
SCSI LUN for this entry.
OBJECT-TYPE    
  INTEGER  

scsiMapAssignedLun 1.3.6.1.4.1.2935.8.2.1.5
Pathlight LUN assigned to this entry. This assigned LUN maps to some device connected to the Gateway/Router by some other means (FC, SSA, SCSI, ...).
OBJECT-TYPE    
  INTEGER  

scsiMapComments 1.3.6.1.4.1.2935.8.2.1.6
User's comments for this entry.
OBJECT-TYPE    
  DisplayString SIZE(0..80)  

scsiMapPdIndex 1.3.6.1.4.1.2935.8.2.1.7
Index into Pathlight SANMgr MIB Device Table ( pd group ). The Device Table has more detailed information about attached devices.
OBJECT-TYPE    
  INTEGER  

deviceMap 1.3.6.1.4.1.2935.9
OBJECT IDENTIFIER    

deviceMapCommand 1.3.6.1.4.1.2935.9.1
Used to issue commands to device map map routines.
OBJECT-TYPE    
  INTEGER clearCopy(1), commit(2), winnow(3), mapClearDatabase(4)  

dmDeviceMap 1.3.6.1.4.1.2935.9.2
Device Map Group *********************************** Each device attached to the Gateway has an entry here. Historical data of devices not presently connected may also appear here.
OBJECT-TYPE    
  SEQUENCE OF  
    DevMapEntry

dmDevMapEntry 1.3.6.1.4.1.2935.9.2.1
OBJECT-TYPE    
  DevMapEntry  

dmRowStatus 1.3.6.1.4.1.2935.9.2.1.1
Row Control Object for this row
OBJECT-TYPE    
  RowStatus  

dmAssignedLun 1.3.6.1.4.1.2935.9.2.1.2
Logical Unit Number assigned to this attached device. Range is 0 thru 255.
OBJECT-TYPE    
  INTEGER  

dmType 1.3.6.1.4.1.2935.9.2.1.3
Type of device (FC, SCSI, SNA, SSA).
OBJECT-TYPE    
  Interface  

dmPort 1.3.6.1.4.1.2935.9.2.1.4
SAN Gateway Port to which this device is connected. May be 1 thru 10 for SCSI, 1 thru 6 for Fibre Channel, 1 thru 3 for SSA.
OBJECT-TYPE    
  INTEGER  

dmTargetId 1.3.6.1.4.1.2935.9.2.1.5
The Target ID of the attached target device. This is the actual target ID of the device, not fabricated by the Gateway or Router.
OBJECT-TYPE    
  INTEGER  

dmTargetLun 1.3.6.1.4.1.2935.9.2.1.6
The Logical Unit Number of the attached target device. This is the actual LUN of the device, not fabricated by the Gateway or Router.
OBJECT-TYPE    
  INTEGER  

dmUid 1.3.6.1.4.1.2935.9.2.1.7
A universally unique identifier for this target device.
OBJECT-TYPE    
  OCTET STRING SIZE(8)  

replication 1.3.6.1.4.1.2935.10
OBJECT IDENTIFIER    

srsDevTable 1.3.6.1.4.1.2935.10.1
Entry point for SAN Replication Service Device Group ***************************************************** Each SAN Replication Service Device has an entry in this table
OBJECT-TYPE    
  SEQUENCE OF  
    SRSDevEntry

srsDevEntry 1.3.6.1.4.1.2935.10.1.1
OBJECT-TYPE    
  SRSDevEntry  

srsDevId 1.3.6.1.4.1.2935.10.1.1.1
Device ID for this SRS Device.
OBJECT-TYPE    
  INTEGER  

srsDevState 1.3.6.1.4.1.2935.10.1.1.2
State of this LUN Replicated Device.
OBJECT-TYPE    
  INTEGER unknown(0), initialized(1), online(2), error(3), deleted(4)  

srsDevCommand 1.3.6.1.4.1.2935.10.1.1.3
Used to invoke SAN Replication Services API commands. Parameters may be passed in the same SNMP Set varbind list with the srsDevCommand as the last varbind. ********************************************* create(1) - Creates a new SRS Device delete(2) - Deletes an existing SRS Device
OBJECT-TYPE    
  INTEGER create(1), remove(2)  

srsDevAssignedLun 1.3.6.1.4.1.2935.10.1.1.4
Assigned LUN of the SAN Replication Service Device's Primary.
OBJECT-TYPE    
  INTEGER  

srsDevMemberCount 1.3.6.1.4.1.2935.10.1.1.5
Number of members of this LUN Replicated Device.
OBJECT-TYPE    
  INTEGER  

srsDevMembersOnline 1.3.6.1.4.1.2935.10.1.1.6
Number of members online.
OBJECT-TYPE    
  INTEGER  

srsDevFlags 1.3.6.1.4.1.2935.10.1.1.7
SCSI device flags for this SAN Replication Service Device.
OBJECT-TYPE    
  INTEGER  

srsDevSizeInBlocks 1.3.6.1.4.1.2935.10.1.1.8
Size in blocks of this SAN Replication Services Device.
OBJECT-TYPE    
  Gauge  

srsDevBlockSize 1.3.6.1.4.1.2935.10.1.1.9
Block size in octets.
OBJECT-TYPE    
  INTEGER  

srsDevPrimary 1.3.6.1.4.1.2935.10.1.1.10
The Assigned LUN of this SRS Device's Primary.
OBJECT-TYPE    
  INTEGER  

srsMemTable 1.3.6.1.4.1.2935.10.2
Entry point for SAN Replication Services Member Group ***************************************************** This table lists the Members of each SRS Device.
OBJECT-TYPE    
  SEQUENCE OF  
    SRSMemEntry

srsMemEntry 1.3.6.1.4.1.2935.10.2.1
OBJECT-TYPE    
  SRSMemEntry  

srsMemDeviceId 1.3.6.1.4.1.2935.10.2.1.1
Device ID of the SAN Replication Services Device to which this member belongs.
OBJECT-TYPE    
  INTEGER  

srsMemId 1.3.6.1.4.1.2935.10.2.1.2
Member ID (index) of this member device.
OBJECT-TYPE    
  INTEGER  

srsMemState 1.3.6.1.4.1.2935.10.2.1.3
State of this SAN Replication Services Device Member.
OBJECT-TYPE    
  INTEGER unknown(0), online(1), synchronized(2), synchronizing(3), suspended(4), readError(5), writeError(6), offline(7)  

srsMemCommand 1.3.6.1.4.1.2935.10.2.1.4
Used to invoke SAN Replication Services API methods. Parameters may be passed in the same SNMP Set varbind list with the lrmCommand as the last varbind.
OBJECT-TYPE    
  INTEGER memberAdd(1), suspend(2), resume(3), remove(4), primarySet(5), fullSynchronize(6), quickSynchronize(7), memberChange(8)  

srsMemType 1.3.6.1.4.1.2935.10.2.1.5
Is this device a primary or secondary member.
OBJECT-TYPE    
  INTEGER primary(1), secondary(2)  

srsMemSyncPoint 1.3.6.1.4.1.2935.10.2.1.6
Number of blocks synchronized so far. Used for monitoring synchronization.
OBJECT-TYPE    
  INTEGER  

srsMemAssignedLun 1.3.6.1.4.1.2935.10.2.1.7
Assigned LUN for this SRS Member.
OBJECT-TYPE    
  INTEGER  

srsMemReadOptions 1.3.6.1.4.1.2935.10.2.1.8
SRS Member read options.
OBJECT-TYPE    
  INTEGER enabled(0), disabled(1)  

srsMemWriteOptions 1.3.6.1.4.1.2935.10.2.1.9
SRS Member write options.
OBJECT-TYPE    
  INTEGER synchronous(0), asynchronous(1)  

envData 1.3.6.1.4.1.2935.11
OBJECT IDENTIFIER    

envDataTable 1.3.6.1.4.1.2935.11.1
Entry point for Environmental Data Group ***************************************************** This table lists the attributes of each environmental data.
OBJECT-TYPE    
  SEQUENCE OF  
    EnvDataEntry

envDataEntry 1.3.6.1.4.1.2935.11.1.1
OBJECT-TYPE    
  EnvDataEntry  

envDataId 1.3.6.1.4.1.2935.11.1.1.1
OBJECT-TYPE    
  INTEGER  

envDataName 1.3.6.1.4.1.2935.11.1.1.2
Name of this environmental data
OBJECT-TYPE    
  DisplayString SIZE(0..64)  

envNominalLo 1.3.6.1.4.1.2935.11.1.1.3
Minimum value for Nominal status Warning state occurs if the current value is less than this
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

envNominalHi 1.3.6.1.4.1.2935.11.1.1.4
Maximum Value for Nominal status Warning state occurs if the current value is greater than this.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

envWarningLo 1.3.6.1.4.1.2935.11.1.1.5
Minimum value for Warning status Alarm state occurs if the current value is less than this
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

envWarningHi 1.3.6.1.4.1.2935.11.1.1.6
Maximum Value for Warning status Alarm state occurs if the current value is greater than this.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

envCurValue 1.3.6.1.4.1.2935.11.1.1.7
Current Value.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

envCurStatus 1.3.6.1.4.1.2935.11.1.1.8
Current Status: Nominal, Warning, or Alarm.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

envUnit 1.3.6.1.4.1.2935.11.1.1.9
Unit
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

trapDefinition 1.3.6.1.4.1.2935.1000
OBJECT IDENTIFIER    

ssaPortUpEvent 1.3.6.1.4.1.2935.1000.1
An SSA Port Up Event has occurred.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

ssaPortDownEvent 1.3.6.1.4.1.2935.1000.2
An SSA Port Down Event has occurred.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

ssaUidAddedEvent 1.3.6.1.4.1.2935.1000.3
An SSA UID Added Event has occurred.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

ssaUidRemovedEvent 1.3.6.1.4.1.2935.1000.4
An SSA UID Removed Event has occurred.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

ssaWebReconfiguredEvent 1.3.6.1.4.1.2935.1000.5
An SSA Web Reconfigured Event has occurred.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

ssaAsyncErrorEvent 1.3.6.1.4.1.2935.1000.6
An SSA Async Error Event has occurred.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

ssaAdapterEvent 1.3.6.1.4.1.2935.1000.7
An SSA Adapter Event has occurred.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

senseDataEvent 1.3.6.1.4.1.2935.1000.8
Sense Data recorded following a check condition. Normally, the host system will request and process sense data, and then perform error recovery.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

unitAttentionEvent 1.3.6.1.4.1.2935.1000.9
A LUN reports a unit attention condition on a non-removable media device.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

ibfEvent 1.3.6.1.4.1.2935.1000.10
An Internal Bus Fault event has occurred.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

temperatureChangeEvent 1.3.6.1.4.1.2935.1000.11
A temperature sensor has reported a change from one of three possible states to a another. The possible states are OK, High, Very High. The display string contained in the varbind paEventVars indicates the initial and final temperature state.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

timeReferenceEvent 1.3.6.1.4.1.2935.1000.12
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

shutdownEvent 1.3.6.1.4.1.2935.1000.13
This unit is shutting down as a result of a restart request.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

diagnosticEvent 1.3.6.1.4.1.2935.1000.14
This event is used for diagnostic purposes.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

configurationEvent 1.3.6.1.4.1.2935.1000.15
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

unexpectedScsiInterruptEvent 1.3.6.1.4.1.2935.1000.16
A SCSI bus reports an unexpected interrupt.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

lipResetEvent 1.3.6.1.4.1.2935.1000.17
A Fibre Channel interface reports a LIP reset was received from a host.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

fcSystemErrorEvent 1.3.6.1.4.1.2935.1000.18
A Fibre Channel interace reports a system error.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

fcRequestTransferErrorEvent 1.3.6.1.4.1.2935.1000.19
A Fibre Channel interface reports an error processing a request.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

fcResponseTransferErrorEvent 1.3.6.1.4.1.2935.1000.20
A Fibre Channel interface reports an error processing a response.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

memoryFaultEvent 1.3.6.1.4.1.2935.1000.21
Processor memory fault detected.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

fcLipEvent 1.3.6.1.4.1.2935.1000.22
A Fibre Channel interface detected a LIP.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

fcLoopUpEvent 1.3.6.1.4.1.2935.1000.23
A Fibre Channel interface reports loop up.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

fcLoopDownEvent 1.3.6.1.4.1.2935.1000.24
A Fibre Channel interface reports loop down.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

pciBusParityErrorEvent 1.3.6.1.4.1.2935.1000.25
Parity error detected on unit internal PCI bus.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

pciInterfaceErrorEvent 1.3.6.1.4.1.2935.1000.26
Interface error detected on unit internal PCI bus.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

scsiDeviceAddedEvent 1.3.6.1.4.1.2935.1000.27
A device has been added to a SCSI bus.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

scsiBusResetEvent 1.3.6.1.4.1.2935.1000.28
A SCSI interface reports a bus reset was detected.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

deviceAddedEvent 1.3.6.1.4.1.2935.1000.29
This unit has added a device to its configuration table. Note: This trap is held off until the unit has been up for 60 seconds.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

deviceRemovedEvent 1.3.6.1.4.1.2935.1000.30
This unit has removed a device from its configuration table.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

loggingStartedEvent 1.3.6.1.4.1.2935.1000.31
Event logging service has started.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

loggingStoppedEvent 1.3.6.1.4.1.2935.1000.32
Event logging service has stopped.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

interfaceBusFaultEvent 1.3.6.1.4.1.2935.1000.33
An interface has detected a bus fault. The display string contained in varbind paEventVars contains the details of which interface detected the fault.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

interfaceDeviceFaultEvent 1.3.6.1.4.1.2935.1000.34
An interface has detected a device fault. The display string contained in varbind paEventVars contains the details of which interface detected the fault.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

scsiUnexpectedDisconnectEvent 1.3.6.1.4.1.2935.1000.35
A SCSI interface has reported an unexpected disconnect by a device.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

scsiParityErrorEvent 1.3.6.1.4.1.2935.1000.36
A SCSI interface has detected a parity error on the bus.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

fcPortDatabaseChangeEvent 1.3.6.1.4.1.2935.1000.37
Fibre Channel port databse change detected.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

ddfMemoryErrorEvent 1.3.6.1.4.1.2935.1000.38
An error was detected on the Direct Data Flow memory board.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

fcDirectoryServerChangeEvent 1.3.6.1.4.1.2935.1000.39
The Directory Server on the Fibre Channel fabric has changed.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

lunLimitExcededEvent 1.3.6.1.4.1.2935.1000.40
The maximum LUN limit has been exceded, too many devices connected.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

fcTransferFailureEvent 1.3.6.1.4.1.2935.1000.41
Fibre Channel transfer error.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

deviceLimitExcededEvent 1.3.6.1.4.1.2935.1000.42
The maximum device limit has been exceded, the persistent device map database is full.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

fcDebugDumpEvent 1.3.6.1.4.1.2935.1000.43
A Fibre Channel interface driver has reported a a debug dump.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

excessiveScsiBusErrorsEvent 1.3.6.1.4.1.2935.1000.44
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

memoryScrubberErrorEvent 1.3.6.1.4.1.2935.1000.45
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

srsDeviceCreatedEvent 1.3.6.1.4.1.2935.1000.46
A new SAN Replication Services device has been created
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

srsDeviceOnlineEvent 1.3.6.1.4.1.2935.1000.47
A SAN Replication Services device has entered the online state.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

srsDeviceRemovedEvent 1.3.6.1.4.1.2935.1000.48
A SAN Replication Services device has been removed (deleted).
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

srsDeviceFailedEvent 1.3.6.1.4.1.2935.1000.49
A SAN Replication Services device has failed.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

srsMemberAddedEvent 1.3.6.1.4.1.2935.1000.50
A new member LUN has been added to a SAN Replication Services device.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

srsMemberSuspendedEvent 1.3.6.1.4.1.2935.1000.51
A SAN Replication Services member has been suspended.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

srsMemberRemovedEvent 1.3.6.1.4.1.2935.1000.52
A SAN Replication Services member has been removed.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

srsMemberSyncStartedEvent 1.3.6.1.4.1.2935.1000.53
A SAN Replication Service member has begun synchronization to the primary member.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

srsMemberSyncDoneEvent 1.3.6.1.4.1.2935.1000.54
A SAN Replication Service member has completed synchronization to the primary member.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

srsMemberSyncErrorEvent 1.3.6.1.4.1.2935.1000.55
An error was detect during synchronization of a SAN Replication Service member to the primary member.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

srsMemberRetryEvent 1.3.6.1.4.1.2935.1000.56
A command issued to a SAN Replication Services member has failed and is being retried.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

srsMemberErrorEvent 1.3.6.1.4.1.2935.1000.57
A command issued to a SAN Replication Services member has resulted in an error.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

envPowerNominalEvent 1.3.6.1.4.1.2935.1000.58
Power has returned to nominal state from a warning or alarm state.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

envPowerWarningEvent 1.3.6.1.4.1.2935.1000.59
Power has entered a warning state from a nominal state (power degrading) or alarm state (power improving).
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

envPowerAlarmEvent 1.3.6.1.4.1.2935.1000.60
Power has entered an alarm state.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

envTemperatureNominalEvent 1.3.6.1.4.1.2935.1000.61
Inlet air, outlet air, or I/O processor temperature has returned to nominal state from a warning or alarm state.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

envInletTemperatureWarningEvent 1.3.6.1.4.1.2935.1000.62
Inlet air temperature has entered a warning state from a nominal state (temperature increasing) or an alarm state (temperature decreasing).
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

envInletTemperatureAlarmEvent 1.3.6.1.4.1.2935.1000.63
Inlet air temperature has entered an alarm state.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

envOutletTemperatureWarningEvent 1.3.6.1.4.1.2935.1000.64
Outlet air temperature has entered a warning state from a nominal state (temperature increasing) or an alarm state (temperature decreasing).
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

envOutletTemperatureAlarmEvent 1.3.6.1.4.1.2935.1000.65
Outlet air temperature has entered an alarm state.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

envFanNominalEvent 1.3.6.1.4.1.2935.1000.66
Fan has entered a nominal state from a fault state.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

envFanWarningEvent 1.3.6.1.4.1.2935.1000.67
Fan has entered a warning range (tachometer fans only).
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

envFanAlarmEvent 1.3.6.1.4.1.2935.1000.68
Fan has entered an alarm range (tachometer fans) or is stalled (rotor stall fans).
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

eccMemoryErrorEvent 1.3.6.1.4.1.2935.1000.69
Error correcting code memory has detected an error.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

firmwareUploadCompleteEvent 1.3.6.1.4.1.2935.1000.70
Firmware upload process has completed.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

restartCompleteEvent 1.3.6.1.4.1.2935.1000.71
Restart process has completed.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

maxInitiatorsExceededEvent 1.3.6.1.4.1.2935.1000.72
Maximum number of initiators has been exceeded.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

powerSupplyOutOfSpecEvent 1.3.6.1.4.1.2935.1000.100
The main power supply voltage is out of specified operating range.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

auxPowerOutOfSpecEvent 1.3.6.1.4.1.2935.1000.101
The auxillary power supply voltage is out of specified operating range.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

newTemperatureChangeEvent 1.3.6.1.4.1.2935.1000.102
Temperature change detected since last report. The possible temperature states are OK, High, and Very High.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

newPciErrorsEvent 1.3.6.1.4.1.2935.1000.103
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

newMemoryParityErrorsEvent 1.3.6.1.4.1.2935.1000.104
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

pciBusInterfaceErrorEvent 1.3.6.1.4.1.2935.1000.105
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

fcInterfaceFailureEvent 1.3.6.1.4.1.2935.1000.106
Fibre Channel interface failed Health Check.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

scsiInterfaceFailureEvent 1.3.6.1.4.1.2935.1000.107
SCSI interface failed Health Check.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

ssaInterfaceFailureEvent 1.3.6.1.4.1.2935.1000.108
SSA interface failed Health Check.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

deviceFailureEvent 1.3.6.1.4.1.2935.1000.109
Target device failed Health Check.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

fcLinkStatusChangeEvent 1.3.6.1.4.1.2935.1000.110
Fibre Channel link status has changed.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

newFcTranferErrorsEvent 1.3.6.1.4.1.2935.1000.111
New Fibre Channel transfer errors were detected since last report.
TRAP-TYPE    
  paTrapSequenceNumber  
  paTime  
  paProducer  
  paEventClass  
  paEventCode  
  paSeq  
  paEventVars  

logWillOverwriteEvent 1.3.6.1.4.1.2935.1000.150
The event log circular buffer is about to wrap, overwriting the oldest entries.
TRAP-TYPE    

bootCompletedEvent 1.3.6.1.4.1.2935.1000.4444
This unit has completed its boot sequence and is ready for SNMP communication with management applications. During the time period between the initiation of the boot (or reboot) sequence and the issuing of the bootCompletedEvent trap, certain data objects may not be completely initialized. As such, management applications should not attempt to retrieve data via SNMP until the bootCompletedEvent is issued.
TRAP-TYPE    

Defined Objects

ProductID  
OBJECT IDENTIFIER    

PathlightProduct  
INTEGER sanGateway(1), sanRouter(2), sanBridge(3), adicFCR2(4), dellFCR2(5), siemensFCR2(6), sanHoneoye(7), adicHoneoye(8), dellHoneoye(9), siemensHoneoye(10), ibmGatewayModule(11)    

Boolean  
INTEGER true(1), false(2)    

RowStatus  
INTEGER active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6)    

LogCommand  
INTEGER idle(0), snapshot(1), scroll(2), save(3), clear(4), removeFile(5), logModeCurrent(6), logModeAbsolute(7), doHealthCheck(8)    

PltStatus  
INTEGER failed(1), down(2), testing(3), up(4)    

FcStatus  
INTEGER configWait(0), loopInit(1), login(2), ready(3), lostSync(4), error(5), reinit(6), nonPart(7), failed(8)    

Interface  
INTEGER none(0), sanGateway(1), ssa(2), fibreChannel(3), scsi(4), ethernet(5), unknown(6), any(7), sanReplication(8)    

Reset  
INTEGER run(0), reset(1), reboot(2)    

BaudRate  
INTEGER baud9600(0), baud19200(1), baud38400(2)    

HealthCheckLevel  
INTEGER none(0), system(1), interface(2), simpleDevice(3), deviceReady(4)    

LogViewingLevel  
INTEGER private(0), notice(1), warning(2), information(3)    

DeviceType  
INTEGER directAccess(0), sequentialAccess(1), printer(2), processor(3), worm(4), cd(5), scanner(6), opticalMemory(7), mediumChanger(8), communications(9), ascIt81(10), ascIt82(11), storageArrayController(12), enclosure(13), simplifiedDirectAccess(14), opticalCardReader(15), unknown(31)    

VendorIDInt  
INTEGER unknown(0), symbios(4096), amd(4130), qlogic(4215), pathlight(4537)    

FibreMedia  
INTEGER unknown(0), copper(1), shortWaveOptical(2), longWaveOptical(3), shortWaveOpticalDual(4), longWaveOpticalDual(5), shortWaveOpticalLongDistance(6), longWaveOpticalLongDistance(7), gbicSWOneGB(8), gbicLW1300OneGB(9), gbicLW1300HPOneGB(10), gbicLW1550HPOneGB(11), gbicCopperHSSDCOneGB(12), gbicCopperDB9OneGB(13), gbicSWTwoGB(14), gbicLW1300TwoGB(15), gbicLW1300HPTwoGB(16), gbicLW1550HPTwoGB(17), gbicCopperHSSDCTwoGB(18), gbicCopperDB9TwoGB(19), noGBIC(20)    

FibrePort  
INTEGER nodeLoop(0), node(1), fabricLoop(3), fabric(4), none(255)    

FibreLoopIDMode  
INTEGER soft(0), hard(1)    

FibrePortMode  
INTEGER privateTargetOnly(1), privateInitiatorOnly(2), privateTargetAndInitiator(3), publicTargetOnly(17), publicInitiatorOnly(18), publicTargetAndInitiator(19)    

FibreConnOptions  
INTEGER loopOnly(0), pointToPointOnly(1), loopPreferred(2), pointToPointPreferred(3)    

SsaSpeed  
INTEGER ssa80(1), ssa160(2)    

PathingAlgorithm  
INTEGER default(0), skipInitiators(1), unknown(2)    

ScsiSpeed  
INTEGER async(0), fast(1), ultra(2), ultra2(3), ultra160(4)    

ScsiRole  
INTEGER target(0), initiator(1)    

ScsiTermination  
INTEGER disabled(0), enabled(1), notPresent(2)    

ScsiCardType  
INTEGER none(0), differentialNoTermination(1), differentialTerminated(2), singleEndedNoTermination(3), singleEndedTerminated(4), unknown(5), lowVoltageSingleEnded(6), lowVoltageDifferential(7), lowVoltageMultiFunction(8)    

ScsiAnsiLevel  
INTEGER notScsi(0), scsi-1(1), scsi-2(2), scsi-3(3)    

LogEntry  
SEQUENCE    
  INTEGER as paIndex  
  TimeTicks as paTime  
  INTEGER as paProducer  
  INTEGER as paEventClass  
  INTEGER as paEventCode  
  INTEGER as paSeq  
  DisplayString as paEventVars SIZE(0..256)  

DevEntry  
SEQUENCE    
  INTEGER as pdIndex  
  DisplayString as pdUID SIZE(16)  
  DeviceType as pdType  
  DisplayString as pdVendor SIZE(8)  
  DisplayString as pdProduct SIZE(16)  
  INTEGER as pdBlockSize  
  Gauge as pdCapacity  
  INTEGER as pdAccess  
  Boolean as pdRemovable  
  PltStatus as pdStatus  
  INTEGER as pdSpeed  
  INTEGER as pdWidth  
  DisplayString as pdSerial SIZE(0..32)  
  INTEGER as pdIdentify  
  Interface as pdInterfaceType  
  INTEGER as pdBus  
  INTEGER as pdId  
  INTEGER as pdLun  
  INTEGER as pdCtlrIndex  
  DisplayString as pdHWRev SIZE(0..32)  
  DisplayString as pdFWRev SIZE(0..32)  
  Reset as pdReset  
  INTEGER as pdStatusBits  
  ScsiAnsiLevel as pdScsiAnsiLevel  
  INTEGER as pdTargetLun  
  IpAddress as pdIpAddress  

CtlrEntry  
SEQUENCE    
  INTEGER as pcIndex  
  Interface as pcType  
  VendorIDInt as pcVendorId  
  INTEGER as pcProductId  
  DisplayString as pcRevision SIZE(0..32)  
  INTEGER as pcSubVendor  
  INTEGER as pcSubProduct  
  INTEGER as pcMaxBurst  
  INTEGER as pcLatency 0..255  
  INTEGER as pcIdentify  
  INTEGER as pcPCIBus  
  INTEGER as pcPCIDev  
  INTEGER as pcPCIFunc  
  Reset as pcReset  
  Boolean as pcRescan  
  OCTET STRING as pcLED SIZE(2)  
  DisplayString as pcHWRev SIZE(0..32)  
  DisplayString as pcFWRev SIZE(0..32)  
  INTEGER as pcPCISlot  
  INTEGER as pcPMCSlot  
  OCTET STRING as pcPCIClass SIZE(3)  
  Boolean as pcSplitMode  
  Gauge as pcChannelMask  
  DisplayString as pcPortHostType SIZE(0..32)  

FcCtlrEntry  
SEQUENCE    
  FcStatus as fcStatus  
  Gauge as fcMaxSpeed  
  DisplayString as fcWWID SIZE(17)  
  DisplayString as fcFWRev SIZE(0..32)  
  DisplayString as fcHWRev SIZE(0..32)  
  INTEGER as fcLoopID -1..127  
  INTEGER as fcFrameSize  
  FibrePort as fcPortType  
  FibreMedia as fcMedia  
  DisplayString as fcSerialNumber SIZE(0..32)  
  FibreLoopIDMode as fcLoopIDMode  
  INTEGER as fcALPhysicalAddress  
  FibrePortMode as fcPortMode  
  FibreConnOptions as fcConnectionOptions  
  INTEGER as fcCtlrChipType  
  Boolean as fcTapeFeature  
  INTEGER as fcHardID -1..256  
  INTEGER as fcCurrentSpeedSetting  
  INTEGER as fcCurrentSpeed  
  INTEGER as fcFrameBufferSize  
  INTEGER as fcLinkFailureCount  
  INTEGER as fcLossSyncCount  
  INTEGER as fcLossSignalCount  
  INTEGER as fcProtocolErrorCount  
  INTEGER as fcInvalidTxWordCount  
  INTEGER as fcInvalidCRCCount  
  DisplayString as fcWWNodeName SIZE(17)  

SSACtlrEntry  
SEQUENCE    
  PltStatus as ssaStatus1  
  PltStatus as ssaStatus2  
  SsaSpeed as ssaSpeed  
  DisplayString as ssaUID SIZE(16)  
  DisplayString as ssaFWRev SIZE(0..32)  
  Gauge as ssaMaxTarg  
  Gauge as ssaMaxInit  
  PathingAlgorithm as ssaPathAlg  
  DisplayString as ssaHWRev SIZE(0..32)  
  INTEGER as ssaMasterPriority 0..7  
  INTEGER as ssaSATAQuota 0..255  
  INTEGER as ssaSATBQuota 0..255  
  INTEGER as ssaSATIQuota 0..255  

SCSICtlrEntry  
SEQUENCE    
  PltStatus as scsiStatus  
  ScsiSpeed as scsiSpeed  
  ScsiRole as scsiRole  
  INTEGER as scsiHostId  
  ScsiSpeed as scsiMaxSpeed  
  ScsiTermination as scsiTerm  
  ScsiCardType as scsiIoCard  
  INTEGER as scsiMaxIds  
  INTEGER as scsiMaxLuns  
  INTEGER as scsiMaxWidth  
  DisplayString as scsiFWRev SIZE(0..32)  
  DisplayString as scsiHWRev SIZE(0..32)  
  Boolean as scsiResetOnPowerUp  
  Boolean as scsiMultiInitEnabled  
  INTEGER as scsiAlternateHostId  

TrapDestEntry  
SEQUENCE    
  INTEGER as pnIndex  
  IpAddress as pnIPAddr  
  INTEGER as pnUdpPort 0..65535  
  INTEGER as pnTrapStyle  

InitiatorEntry  
SEQUENCE    
  INTEGER as hostIndex  
  INTEGER as hostRowStatus  
  DisplayString as hostWWName SIZE(0..32)  
  DisplayString as hostName SIZE(0..32)  
  DisplayString as hostType SIZE(0..32)  
  DisplayString as hostPortID SIZE(0..32)  
  INTEGER as hostSANConnection  
  INTEGER as hostConnectionType  
  OCTET STRING as hostITLData SIZE(256)  
  IpAddress as hostIPAddr  

ScsiMapEntry  
SEQUENCE    
  RowStatus as scsiMapRowStatus  
  INTEGER as scsiMapPort  
  INTEGER as scsiMapTid  
  INTEGER as scsiMapLun  
  INTEGER as scsiMapAssignedLun  
  DisplayString as scsiMapComments SIZE(0..80)  
  INTEGER as scsiMapPdIndex  

DevMapEntry  
SEQUENCE    
  RowStatus as dmRowStatus  
  INTEGER as dmAssignedLun  
  Interface as dmType  
  INTEGER as dmPort  
  INTEGER as dmTargetId  
  INTEGER as dmTargetLun  
  OCTET STRING as dmUid SIZE(8)  

SRSDevEntry  
SEQUENCE    
  INTEGER as srsDevId  
  INTEGER as srsDevState  
  INTEGER as srsDevCommand  
  INTEGER as srsDevAssignedLun  
  INTEGER as srsDevMemberCount  
  INTEGER as srsDevMembersOnline  
  INTEGER as srsDevFlags  
  Gauge as srsDevSizeInBlocks  
  INTEGER as srsDevBlockSize  
  INTEGER as srsDevPrimary  

SRSMemEntry  
SEQUENCE    
  INTEGER as srsMemDeviceId  
  INTEGER as srsMemId  
  INTEGER as srsMemState  
  INTEGER as srsMemCommand  
  INTEGER as srsMemType  
  INTEGER as srsMemSyncPoint  
  INTEGER as srsMemAssignedLun  
  INTEGER as srsMemReadOptions  
  INTEGER as srsMemWriteOptions  

EnvDataEntry  
SEQUENCE    
  INTEGER as envDataId  
  DisplayString as envDataName SIZE(0..64)  
  DisplayString as envNominalLo SIZE(0..32)  
  DisplayString as envNominalHi SIZE(0..32)  
  DisplayString as envWarningLo SIZE(0..32)  
  DisplayString as envWarningHi SIZE(0..32)  
  DisplayString as envCurValue SIZE(0..32)  
  DisplayString as envCurStatus SIZE(0..32)  
  DisplayString as envUnit SIZE(0..32)