SATELCOM-MIB

File: SATELCOM-MIB.mib (233451 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
RFC-1215

Imported symbols

Counter NetworkAddress enterprises
DisplayString mib-2 OBJECT-TYPE
TRAP-TYPE

Defined Objects

satelcom 1.3.6.1.4.1.397
OBJECT IDENTIFIER    

errorLogReport 1.3.6.1.4.1.397.0
Enterprise Specific trap for MegaPAC. The Error Log entry in ascii format
TRAP-TYPE    
  elogRecord  

products 1.3.6.1.4.1.397.1
OBJECT IDENTIFIER    

sysRestart 1.3.6.1.4.1.397.1
Enterprise Specific trap for MegaPAC System restart.
TRAP-TYPE    
  elogRecord  

megaPAC-E-cpu-C 1.3.6.1.4.1.397.1.1
OBJECT IDENTIFIER    

megaPAC-N-series 1.3.6.1.4.1.397.1.2
OBJECT IDENTIFIER    

megaPAC-E-cpu-D 1.3.6.1.4.1.397.1.3
OBJECT IDENTIFIER    

megaCARD 1.3.6.1.4.1.397.1.4
OBJECT IDENTIFIER    

arm-Router 1.3.6.1.4.1.397.1.5
OBJECT IDENTIFIER    

megaPAC-V-cpu-8 1.3.6.1.4.1.397.1.6
OBJECT IDENTIFIER    

megaPAC-V-cpu-16 1.3.6.1.4.1.397.1.7
OBJECT IDENTIFIER    

megaPAC-V-cpu-68040 1.3.6.1.4.1.397.1.8
OBJECT IDENTIFIER    

megaPAD 1.3.6.1.4.1.397.1.9
OBJECT IDENTIFIER    

megapac-2001 1.3.6.1.4.1.397.1.10
OBJECT IDENTIFIER    

micropad-2 1.3.6.1.4.1.397.1.11
OBJECT IDENTIFIER    

micropad-4 1.3.6.1.4.1.397.1.12
OBJECT IDENTIFIER    

micropad-8 1.3.6.1.4.1.397.1.13
OBJECT IDENTIFIER    

duo-Card-MBOX 1.3.6.1.4.1.397.1.14
OBJECT IDENTIFIER    

duo-Card-System 1.3.6.1.4.1.397.1.15
OBJECT IDENTIFIER    

megaBox-CPU-C 1.3.6.1.4.1.397.1.16
OBJECT IDENTIFIER    

megaBox-CPU-D 1.3.6.1.4.1.397.1.17
OBJECT IDENTIFIER    

megaBox-CPU-E 1.3.6.1.4.1.397.1.18
OBJECT IDENTIFIER    

megaPac-E-CPU-C-Dual 1.3.6.1.4.1.397.1.19
OBJECT IDENTIFIER    

megaPac-E-CPU-D-Dual 1.3.6.1.4.1.397.1.20
OBJECT IDENTIFIER    

megaPac-E-CPU-E-Dual 1.3.6.1.4.1.397.1.21
OBJECT IDENTIFIER    

megaPac-E-CPU-C-Dual-Fan 1.3.6.1.4.1.397.1.22
OBJECT IDENTIFIER    

megaPac-E-CPU-D-Dual-Fan 1.3.6.1.4.1.397.1.23
OBJECT IDENTIFIER    

megaPac-E-CPU-E-Dual-Fan 1.3.6.1.4.1.397.1.24
OBJECT IDENTIFIER    

megaPac-E-CPU-C-Dual-Fan-48V 1.3.6.1.4.1.397.1.25
OBJECT IDENTIFIER    

megaPac-E-CPU-D-Dual-Fan-48V 1.3.6.1.4.1.397.1.26
OBJECT IDENTIFIER    

megaPac-E-CPU-E-Dual-Fan-48V 1.3.6.1.4.1.397.1.27
OBJECT IDENTIFIER    

megaPAC-E-cpu-E 1.3.6.1.4.1.397.1.28
OBJECT IDENTIFIER    

megaPac-V-Dual-PSU 1.3.6.1.4.1.397.1.29
OBJECT IDENTIFIER    

megaPac-V-Dual-PSU-48V 1.3.6.1.4.1.397.1.30
OBJECT IDENTIFIER    

megapac-20EM 1.3.6.1.4.1.397.1.31
OBJECT IDENTIFIER    

megapac-21EM 1.3.6.1.4.1.397.1.32
OBJECT IDENTIFIER    

megapac-2002 1.3.6.1.4.1.397.1.33
OBJECT IDENTIFIER    

megapac-2003 1.3.6.1.4.1.397.1.34
OBJECT IDENTIFIER    

base 1.3.6.1.4.1.397.2
OBJECT IDENTIFIER    

baseVersion 1.3.6.1.4.1.397.2.1
Software Version. The software version currently running. Defined as YMMR (i.e. Year, Month, Revision
OBJECT-TYPE    
  DisplayString SIZE(4)  

baseRestartTime 1.3.6.1.4.1.397.2.2
BASE Restart Time. The time and data of the last system restart (i.e. power-on or last BOOT)
OBJECT-TYPE    
  DisplayString SIZE(20)  

baseMaxPacketSize 1.3.6.1.4.1.397.2.3
Node Maximum Packet Size. The maximum single buffer size available on the MegaPAC.
OBJECT-TYPE    
  INTEGER  

baseBuffPoolMax 1.3.6.1.4.1.397.2.4
Node Buffer Pool Maximum. The maximum number of buffers available temporary storage of transitting data.
OBJECT-TYPE    
  INTEGER  

baseBuffPoolNow 1.3.6.1.4.1.397.2.5
Node Current Buffer Pool. The current number of free buffers available temporary storage of transitting data.
OBJECT-TYPE    
  INTEGER  

baseBufferPoolLowest 1.3.6.1.4.1.397.2.6
Node Buffer Pool Lowest. The lowest value the buffer pool has ever reached.
OBJECT-TYPE    
  INTEGER  

baseBufferPoolEmpty 1.3.6.1.4.1.397.2.7
Node Buffer Pool Empty. The number of times that the free buffer pool has fallen below the minimum buffer threshold 'baseBuffThreshold'.
OBJECT-TYPE    
  INTEGER  

baseStatBufferThreshold 1.3.6.1.4.1.397.2.8
Node Buffer Threshold. When the number of buffers in the free buffer pool reaches this threshold, flow control will occur.
OBJECT-TYPE    
  INTEGER 5..1000  

baseMemorySize 1.3.6.1.4.1.397.2.9
Node Memory Size. The size of the system memory installed in the MegaPAC.
OBJECT-TYPE    
  INTEGER  

baseDataFramesIn 1.3.6.1.4.1.397.2.10
Node Frames In. The total number of frames received by the MegaPAC.
OBJECT-TYPE    
  Counter  

baseDataFramesOut 1.3.6.1.4.1.397.2.11
Node Frames Out. The total number of frames transmitted by the MegaPAC.
OBJECT-TYPE    
  Counter  

baseDataFrameRateIn 1.3.6.1.4.1.397.2.12
Node Frame Rate In. The rate measured in frames per second that the MegaPAC is currently receiving frames.
OBJECT-TYPE    
  Counter  

baseDataFrameRateOut 1.3.6.1.4.1.397.2.13
Node Frames Rate Out. The rate measured in frames per second that the MegaPAC is currently transmitting frames.
OBJECT-TYPE    
  Counter  

baseTotalCallSetUps 1.3.6.1.4.1.397.2.14
Node Total Call Set ups. The total number of calls successfully established by the MegaPAC.
OBJECT-TYPE    
  Counter  

baseCurrentCalls 1.3.6.1.4.1.397.2.15
Current calls. The number of calls currently active on the MegaPAC.
OBJECT-TYPE    
  Counter  

baseRetransmissions 1.3.6.1.4.1.397.2.16
Node Retransmissions. The total number of frames which have been retransmitted by the MegaPAC.
OBJECT-TYPE    
  Counter  

baseRejects 1.3.6.1.4.1.397.2.17
Node Rejects. The total number of frames that have been rejected by the MegaPAC.
OBJECT-TYPE    
  Counter  

baseTotalTransportCalls 1.3.6.1.4.1.397.2.18
Node Total Transport calls. The total number of transport calls established by the MegaPAC.
OBJECT-TYPE    
  Counter  

baseCurrentTransportCalls 1.3.6.1.4.1.397.2.19
Current Transport Calls. The number of transport calls currently active on the MegaPAC.
OBJECT-TYPE    
  Counter  

baseRunStatus 1.3.6.1.4.1.397.2.20
Node Run Status. This parameter indicates whether the operating system has been 'Booted' from RAM (TELELOAD) or EPROM (default).
OBJECT-TYPE    
  INTEGER prom(1), ram(2)  

baseReports 1.3.6.1.4.1.397.2.21
Node Reporting channel. The name of the logical resource (channel) that the system reports will be directed to.
OBJECT-TYPE    
  DisplayString SIZE(4)  

baseSessionStatistics 1.3.6.1.4.1.397.2.22
Node Session Statistics reporting channel. The name of the logical resource (channel) that the system session statistics will be directed to.
OBJECT-TYPE    
  DisplayString SIZE(4)  

baseBufferThreshold 1.3.6.1.4.1.397.2.23
Node Buffer Threshold. The threshold before flow control is invoked
OBJECT-TYPE    
  INTEGER 5..1000  

baseInitialPresentationTimer 1.3.6.1.4.1.397.2.24
Node Initial Presentation Timer. The maximum time allowed between initial connection to the presentation service and the user entering a valid resource. The call will be disconnected if this timer elapses.
OBJECT-TYPE    
  INTEGER 0..300  

baseSecondaryPresentationTimer 1.3.6.1.4.1.397.2.25
Node Secondary Presentation Timer. After a call has been cleared by the Host DTE the user has the option to use the presentation service to establish another call, failure to do so within this time period will result in the initial call being cleared.
OBJECT-TYPE    
  INTEGER 0..300  

baseInactivityDetectTimer 1.3.6.1.4.1.397.2.26
Node Inactivity Timer. This timer will cause calls to be cleared if the IDLE option has been configured on the channel.
OBJECT-TYPE    
  INTEGER 0..30  

baseSegmentAccounting 1.3.6.1.4.1.397.2.27
Node Segment Accounting. This parameter causes the frames in/out parameters to be displayed in terms of 64 byte SEGMENTS rather than frames.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

baseTerminalEmulationBuffers 1.3.6.1.4.1.397.2.28
Terminal Emulation Buffers. The number of system buffers allocated for Terminal Emulation purposes.
OBJECT-TYPE    
  INTEGER 0..640  

baseTransportBuffers 1.3.6.1.4.1.397.2.29
Transport Buffers. The number of transport buffers allocated for TP 0,2,3,4 sessions.
OBJECT-TYPE    
  INTEGER 0..2048  

baseCountrySettings 1.3.6.1.4.1.397.2.30
Country Setting. Invokes the ASCII representation of the Japanese character set.
OBJECT-TYPE    
  INTEGER none(1), japn(2)  

baseTeleloadEnabled 1.3.6.1.4.1.397.2.31
Teleload enable. If set to yes the MegaPAC software may be downloaded by ASCII file transfer.
OBJECT-TYPE    
  INTEGER no(1), yes(2), k256(3), k160(129)  

baseDefaultToPromCompatible 1.3.6.1.4.1.397.2.32
Cold Boot From PROM. If set to yes the MegaPAC software may be downloaded by ASCII file transfer.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

baseCommand 1.3.6.1.4.1.397.2.33
Allows SNMP manager to execute commands.
OBJECT-TYPE    
  INTEGER none(1), systemBoot(2), restart(3), stop(4), dele(5), clearVcp(6), run(7), halt(8), readBill(9)  

baseCommandControllerIndex 1.3.6.1.4.1.397.2.34
Sets controller index for baseCommands where relevant.
OBJECT-TYPE    
  INTEGER  

baseCommandChannelndex 1.3.6.1.4.1.397.2.35
Sets channel index for baseCommands where relevant.
OBJECT-TYPE    
  INTEGER  

baseConnectedToProtocol 1.3.6.1.4.1.397.2.36
Indicates the VCP state. NULL is VCP free; a returned value indicates BUSY and maps the access protocol.
OBJECT-TYPE    
  INTEGER x25(1), llc2(2), null(3), epci(4), base(5), hdlc(8), qllc(9), xlan(10), ilan(11), term(12), lan(13), clus(14), mult(15), sdlc(16), ip(17), ace(18), v25b(19), cons(20), nms(21), dlc(22), map(23), tlan(24), snmp(25), nfrm(26), xfrm(27), tip(28), rout(29), ppp(30), ipx(31), tipx(32), esis(34), tsis(35), sip(36), smdx(37), dlcx(38), edlc(39), comp(40), bond(41), eses(42), rlay(43), lap(44), isdp(45), isdb(46), oem1(47), mman(48)  

baseBillingThreshold 1.3.6.1.4.1.397.2.37
Sets threshold for billing alarms - entry written to ELOG file, and trap sent.
OBJECT-TYPE    
  INTEGER  

baseBillUnread 1.3.6.1.4.1.397.2.38
Number of BILLING records outstanding - to be read by SNMP manager.
OBJECT-TYPE    
  INTEGER  

baseCurrentBill 1.3.6.1.4.1.397.2.39
Record number of current available BILLING record.
OBJECT-TYPE    
  INTEGER  

baseBillRecordBuffer 1.3.6.1.4.1.397.2.40
The current BILLING record data.
OBJECT-TYPE    
  DisplayString SIZE(150)  

baseCurrentConfig 1.3.6.1.4.1.397.2.41
A decimal number from 0000 to 9999 representing the current configuration.
OBJECT-TYPE    
  INTEGER  

baseCommandBuffer 1.3.6.1.4.1.397.2.44
The VCP single line command string buffer.
OBJECT-TYPE    
  DisplayString SIZE(50)  

baseCommandLength 1.3.6.1.4.1.397.2.45
The length in Hex of the single line command string.
OBJECT-TYPE    
  INTEGER  

baseEMPresent 1.3.6.1.4.1.397.2.46
Indicator of whether Environmental Monitor is present.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

baseEMTempTens 1.3.6.1.4.1.397.2.47
Tens part of Environmental Monitor temperature.
OBJECT-TYPE    
  INTEGER  

baseEMTempUnits 1.3.6.1.4.1.397.2.48
Unit part of Environmental Monitor temperature.
OBJECT-TYPE    
  INTEGER  

baseEMFan1 1.3.6.1.4.1.397.2.49
Environmental Monitor Fan 1 state.
OBJECT-TYPE    
  INTEGER none(1), ok(2), fail(3)  

baseEMFan2 1.3.6.1.4.1.397.2.50
Environmental Monitor Fan 2 state.
OBJECT-TYPE    
  INTEGER none(1), ok(2), fail(3)  

baseEMFan3 1.3.6.1.4.1.397.2.51
Environmental Monitor Fan 3 state.
OBJECT-TYPE    
  INTEGER none(1), ok(2), fail(3)  

baseEMVoltage 1.3.6.1.4.1.397.2.52
Environmental Monitor voltage.
OBJECT-TYPE    
  DisplayString SIZE(4)  

baseEMPsu1 1.3.6.1.4.1.397.2.53
Environmental Monitor PSU 1 state.
OBJECT-TYPE    
  INTEGER none(1), ok(2), fail(3)  

baseEMPsu2 1.3.6.1.4.1.397.2.54
Environmental Monitor PSU 2 state.
OBJECT-TYPE    
  INTEGER none(1), ok(2), fail(3)  

baseCPUUtil 1.3.6.1.4.1.397.2.55
CPU utilisation in the range 0 to 100.
OBJECT-TYPE    
  INTEGER  

controller 1.3.6.1.4.1.397.3
OBJECT IDENTIFIER    

ctrlNumberConfigured 1.3.6.1.4.1.397.3.1
Total Number of Controllers Configured. The number of controllers in the MegaPAC which have been configured.
OBJECT-TYPE    
  INTEGER  

ctrlTotalNumber 1.3.6.1.4.1.397.3.2
Total Number of Controllers. The TOTAL number of controllers in the MegaPAC including unconfigured (NULL) controllers.
OBJECT-TYPE    
  INTEGER  

ctrlStatTable 1.3.6.1.4.1.397.3.3
OBJECT-TYPE    
  SEQUENCE OF  
    CtrlStatEntry

ctrlStatEntry 1.3.6.1.4.1.397.3.3.1
OBJECT-TYPE    
  CtrlStatEntry  

ctrlStatIndex 1.3.6.1.4.1.397.3.3.1.1
Controller index. The position of this controller in relation to 'BASE'. i.e. BASE = 0 NMSC = 1 PS01 = 2 ...
OBJECT-TYPE    
  INTEGER  

ctrlStatName 1.3.6.1.4.1.397.3.3.1.2
Controller name. The unique 4 character name by which this controller is known.
OBJECT-TYPE    
  DisplayString SIZE(4)  

ctrlStatType 1.3.6.1.4.1.397.3.3.1.3
Controller Type. The type of software controller.
OBJECT-TYPE    
  INTEGER x25(1), llc2(2), null(3), epci(4), base(5), hdlc(8), qllc(9), xlan(10), ilan(11), term(12), lan(13), clus(14), mult(15), sdlc(16), ip(17), ace(18), v25b(19), cons(20), nms(21), dlc(22), map(23), tlan(24), snmp(25), nfrm(26), xfrm(27), tip(28), rout(29), ppp(30), ipx(31), tipx(32), esis(34), tsis(35), sip(36), smdx(37), dlcx(38), edlc(39), comp(40), bond(41), eses(42), rlay(43), lap(44), isdp(45), isdb(46), oem1(47), mman(48)  

ctrlStatSubType 1.3.6.1.4.1.397.3.3.1.4
Sub Type. The serial I/O board installed.
OBJECT-TYPE    
  INTEGER none(1), sio(2), xio(3), auto(4), gio(5), pri(9), scc(17), vio(33), rio(65)  

ctrlStatNumberChannels 1.3.6.1.4.1.397.3.3.1.5
Channel Count. The number of channels assigned to a controller.
OBJECT-TYPE    
  INTEGER  

ctrlStatFirstChannelIndex 1.3.6.1.4.1.397.3.3.1.6
First Channnel. The 1st channel index number used by the controller : PPP, X.25, XFRM, NFRM VFRM, CONS, IP, TIP, IPX, TIPX, ESIS, DLC, LAN, TLAN, ILAN, XLAN SDLC, TERM, QLLC & HDLC
OBJECT-TYPE    
  INTEGER  

ctrlStatCRCErrors 1.3.6.1.4.1.397.3.3.1.7
CRC Errors. The number of packets received for which the checksum was not valid.
OBJECT-TYPE    
  Counter  

ctrlStatTotalCallSetUps 1.3.6.1.4.1.397.3.3.1.8
Total Call Set ups. The total number of successful calls established on this link.
OBJECT-TYPE    
  Counter  

ctrlStatCurrentCalls 1.3.6.1.4.1.397.3.3.1.9
Current Calls. The number of calls currently active on this link.
OBJECT-TYPE    
  INTEGER  

ctrlStatDataIn 1.3.6.1.4.1.397.3.3.1.10
Data bytes In.
OBJECT-TYPE    
  Counter  

ctrlStatDataOut 1.3.6.1.4.1.397.3.3.1.11
Data Out. The total number of data bytes transmitted on this link.
OBJECT-TYPE    
  Counter  

ctrlStatDataFramesIn 1.3.6.1.4.1.397.3.3.1.12
Data Frames In. The total number of data frames received on this link.
OBJECT-TYPE    
  Counter  

ctrlStatDataFramesOut 1.3.6.1.4.1.397.3.3.1.13
Data Frames Out. The total number of data frames transmitted on this link.
OBJECT-TYPE    
  Counter  

ctrlStatDataFrameRateIn 1.3.6.1.4.1.397.3.3.1.14
Data Frame Rate In. The rate that frames are arriving on this link, specified in frames per second.
OBJECT-TYPE    
  INTEGER  

ctrlStatDataFrameRateOut 1.3.6.1.4.1.397.3.3.1.15
Data Frame Frate Out. The rate that frames are being transmitted on this link, specified in frames per second.
OBJECT-TYPE    
  INTEGER  

ctrlStatCallsReceived 1.3.6.1.4.1.397.3.3.1.16
Calls Received. The total number of incoming call requests seen on this link.
OBJECT-TYPE    
  Counter  

ctrlStatCallsSent 1.3.6.1.4.1.397.3.3.1.17
Calls Sent. The total number of call requests sent out on this link.
OBJECT-TYPE    
  Counter  

ctrlStatClearsReceived 1.3.6.1.4.1.397.3.3.1.18
Clears Received. The total number of call clear requests received on this link.
OBJECT-TYPE    
  Counter  

ctrlStatRetransmissions 1.3.6.1.4.1.397.3.3.1.19
Retransmissions. The number of packets that have been transmitted more than once on this link.
OBJECT-TYPE    
  Counter  

ctrlStatRejects 1.3.6.1.4.1.397.3.3.1.20
Rejects. The total number of packets which have been rejected on this link.
OBJECT-TYPE    
  Counter  

ctrlStatState 1.3.6.1.4.1.397.3.3.1.21
State. The level 2 data state of the link.
OBJECT-TYPE    
  INTEGER disc(1), sabm(9), data(11), blkd(13), wake(15), cls(17), frmr(19), stop(21), xidr(23), xidc(25)  

ctrlStatSubState 1.3.6.1.4.1.397.3.3.1.22
Sub State. The level 3 state of this link.
OBJECT-TYPE    
  INTEGER norm(1), rej(5), disc(9)  

ctrlStatNoTries 1.3.6.1.4.1.397.3.3.1.23
Tries. The number of un-numbered control frames sent to try and establish the link.
OBJECT-TYPE    
  Counter  

ctrlStatOptions 1.3.6.1.4.1.397.3.3.1.24
Options The options currently configured for this link. Note, that the values returned by the MegaPAC may be additive values - representing combined combinations for the table listed e.g. poll+ext.
OBJECT-TYPE    
  INTEGER norm(1), iso1984(16385), poll(32769), ext(8193), hold(4097), stat(2049), net(257), dmod(1025), dcd(513), ui(17), xidc(5), xidr(9), test(3), dtr(2), tcp(65), idle(33), poll-ext(40961), poll-dcd(33281), poll-ext-dcd(41473)  

ctrlStatLCGN 1.3.6.1.4.1.397.3.3.1.25
LCGN The logical channel group number for this link.
OBJECT-TYPE    
  INTEGER  

ctrlStatResetsReceived 1.3.6.1.4.1.397.3.3.1.26
Resets Received. The total number of reset packets received on this link.
OBJECT-TYPE    
  Counter  

ctrlStatInterruptsReceived 1.3.6.1.4.1.397.3.3.1.27
Interupts Received. The total number of interrupt packets received on this link.
OBJECT-TYPE    
  Counter  

ctrlStatOuputQueueLength 1.3.6.1.4.1.397.3.3.1.28
Output Queue Length. The number of packets queued for transmission on this link.
OBJECT-TYPE    
  INTEGER  

ctrlStatStationAddress 1.3.6.1.4.1.397.3.3.1.29
Local MAC Address The MAC Address of the MegaPAC.
OBJECT-TYPE    
  DisplayString SIZE(12)  

ctrlStatDestinationAddress 1.3.6.1.4.1.397.3.3.1.30
Destination MAC Address. The MAC Address of the destination device.
OBJECT-TYPE    
  DisplayString SIZE(12)  

ctrlStatEIA 1.3.6.1.4.1.397.3.3.1.31
EIA state. Displays the EIA signals currently on the link.
OBJECT-TYPE    
  DisplayString SIZE(8)  

ctrlStatSdlcOptions 1.3.6.1.4.1.397.3.3.1.32
SDLC Options. A range of link level options used for establishing IBM connections.
OBJECT-TYPE    
  INTEGER none(1), pu4(33), wait(65), xid(129), idle(17), wait-xid(193)  

ctrlStatArpRequestRec 1.3.6.1.4.1.397.3.3.1.33
ARP Requests Received. The number of ARP requests sent to the MegaPAC
OBJECT-TYPE    
  INTEGER  

ctrlStatArpRequestSent 1.3.6.1.4.1.397.3.3.1.34
ARP Requests Sent. The number of ARP requests processed to the local LAN by the MegaPAC
OBJECT-TYPE    
  INTEGER  

ctrlStatArpResponsesRec 1.3.6.1.4.1.397.3.3.1.35
ARP Respones Received. The number of ARP responses returned to the the MegaPAC
OBJECT-TYPE    
  INTEGER  

ctrlStatTestType 1.3.6.1.4.1.397.3.3.1.36
Allows SNMP manager to set V54 tests; local or remote or off.
OBJECT-TYPE    
  INTEGER loopModeOff(1), loopModeRemote(5), loopModeLocal(9)  

ctrlStatTestSet 1.3.6.1.4.1.397.3.3.1.37
Allows SNMP manager to apply the local/remote V54 test selection.
OBJECT-TYPE    
  INTEGER loopModeEstablished(1), loopModeRequested(2)  

ctrlStatTest 1.3.6.1.4.1.397.3.3.1.38
Allows SNMP manager to activate local/remote V54 test.
OBJECT-TYPE    
  INTEGER loopTestEstablished(1), loopTestRequested(2)  

ctrlStatLstate 1.3.6.1.4.1.397.3.3.1.39
Allows SNMP manager to read Local Loop test result.
OBJECT-TYPE    
  INTEGER localLoopNoStatus(1), localLoopPass(2), localLoopFail(3)  

ctrlStatRstate 1.3.6.1.4.1.397.3.3.1.40
Allows SNMP manager to read Remote Loop test result.
OBJECT-TYPE    
  INTEGER remoteLoopNoStatus(1), remoteLoopPass(2), remoteLoopFail(3)  

ctrlParamTable 1.3.6.1.4.1.397.3.4
The controller configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    CtrlParamEntry

ctrlParamEntry 1.3.6.1.4.1.397.3.4.1
An individual controller configuration.
OBJECT-TYPE    
  CtrlParamEntry  

ctrlParamIndex 1.3.6.1.4.1.397.3.4.1.1
Index The position of this controller in relation to 'BASE'. i.e. BASE = 0 NMSC = 1 PS01 = 2 ...
OBJECT-TYPE    
  INTEGER  

ctrlParamName 1.3.6.1.4.1.397.3.4.1.2
Name. The unique 4 character name by which this controller is known.
OBJECT-TYPE    
  DisplayString SIZE(4)  

ctrlParamType 1.3.6.1.4.1.397.3.4.1.3
Type. The type of controller
OBJECT-TYPE    
  INTEGER x25(1), llc2(2), null(3), epci(4), base(5), hdlc(8), qllc(9), xlan(10), ilan(11), term(12), lan(13), clus(14), mult(15), sdlc(16), ip(17), ace(18), v25b(19), cons(20), nms(21), dlc(22), map(23), tlan(24), snmp(25), nfrm(26), xfrm(27), tip(28), rout(29), ppp(30), ipx(31), tipx(32), esis(34), tsis(35), sip(36), smdx(37), dlcx(38), edlc(39), comp(40), bond(41), eses(42), rlay(43), lap(44), isdp(45), isdb(46), oem1(47), mman(48)  

ctrlParamSubType 1.3.6.1.4.1.397.3.4.1.4
Sub-Type. The link between the controller and its associated hardware type.
OBJECT-TYPE    
  INTEGER none(1), sio(2), xio(3), auto(4), gio(5), pri(9), scc(17), vio(33), rio(65)  

ctrlParamNoChannels 1.3.6.1.4.1.397.3.4.1.5
Number of channels. The number of logical channels configured on the controller.
OBJECT-TYPE    
  INTEGER 0..4096  

ctrlParamSpeed 1.3.6.1.4.1.397.3.4.1.6
Speed. The clock speed of the interface.
OBJECT-TYPE    
  INTEGER bps-2000000(19), bps-1000000(18), bps-512000(17), bps-256000(16), bps-128000(15), bps-64000(14), bps-1200(13), bps-19200(12), bps-9600(11), bps-7200(10), bps-4800(9), bps-3600(8), bps-2400(7), bps-2000(6), bps-1800(5), bps-1200(4), bps-600(3), bps-300(2), ext-clock(1)  

ctrlParamInterfaceType 1.3.6.1.4.1.397.3.4.1.7
The serial interface type. Note, Only applicable to MegaCard.
OBJECT-TYPE    
  INTEGER x21(2), v35(3), v24(1), epci(68)  

ctrlParamPacketSize 1.3.6.1.4.1.397.3.4.1.8
Packet Size. The maximum packet size in bytes of outgoing packets, this parameter must be less than or equal to the 'BASE' statistic 'maxPacketSize'.
OBJECT-TYPE    
  INTEGER bytes-32(2), bytes-64(3), bytes-128(5), bytes-256(9), bytes-512(17), bytes-1024(33), tran(1)  

ctrlParamV54Modem 1.3.6.1.4.1.397.3.4.1.9
V54 Modem. Enable V54 loop back testing. Note this does not initiate loop back testing, the loop back is initiated by typing in the 'TEST' command.
OBJECT-TYPE    
  INTEGER yes(61), no(1)  

ctrlParamAddress 1.3.6.1.4.1.397.3.4.1.10
Address. The logical address designation of the controller.
OBJECT-TYPE    
  INTEGER dte-a(1), dce-b(2)  

ctrlParamOptions 1.3.6.1.4.1.397.3.4.1.11
Options. A range of controller options, options may be specified individually or added together.
OBJECT-TYPE    
  INTEGER none(1), iso1984(16385), poll(32769), poll-net(33025), ext(8193), hold(4097), stat(2049), net(257), dmod(1025), dcd(513), ui(17), xidc(5), xidr(9), test(3), dtr(2), tcp(65), idle(33), poll-ext(40961), poll-dcd(33281), poll-ext-dcd(41473)  

ctrlParamInitFrame 1.3.6.1.4.1.397.3.4.1.12
Initial Frame.
OBJECT-TYPE    
  INTEGER sabm(48), sabm-pbit(64), disc(68), disc-pbit(84), none(1)  

ctrlParamT1 1.3.6.1.4.1.397.3.4.1.13
T1. Timer for retransmission of unacknowleged frames. Specified in 0.1 second units.
OBJECT-TYPE    
  INTEGER 2..80  

ctrlParamTries 1.3.6.1.4.1.397.3.4.1.14
Tries. The number of times a frame will be retransmitted before a link restart is initiated.
OBJECT-TYPE    
  INTEGER 2..50  

ctrlParamKLevel2 1.3.6.1.4.1.397.3.4.1.15
KLevel 2. The level 2 window size.
OBJECT-TYPE    
  INTEGER 1..31  

ctrlParamKLevel3 1.3.6.1.4.1.397.3.4.1.16
KLevel 3. The level 3 window size.
OBJECT-TYPE    
  INTEGER 1..127  

ctrlParamLineGroup 1.3.6.1.4.1.397.3.4.1.17
Line Group. The line group is used for load sharing. If two links have same (non-zero) line group then data may be shared between them.
OBJECT-TYPE    
  INTEGER 0..15  

ctrlParamLCGN 1.3.6.1.4.1.397.3.4.1.18
LCGN. The logical channel group number for this link.
OBJECT-TYPE    
  INTEGER 0..15  

ctrlParamLCNOffset 1.3.6.1.4.1.397.3.4.1.19
LCN Offset. This parameter is used in conjunction with the LCGN. It's purpose is to shift the channel range by the appropriate offset.
OBJECT-TYPE    
  INTEGER 0..4095  

ctrlParamAddressGroup 1.3.6.1.4.1.397.3.4.1.20
Address Group. This parameter is used in conjunction with the address group field in the x25 file to provide different addressing domains.
OBJECT-TYPE    
  INTEGER 0..15  

ctrlParamFrameSequence 1.3.6.1.4.1.397.3.4.1.21
Frame Sequence. This parameter determines if normal or extended frame sequencing is supported.
OBJECT-TYPE    
  INTEGER extended(15), normal(7)  

ctrlParamCallTimeOut 1.3.6.1.4.1.397.3.4.1.22
Call Time Out. The time in seconds the MegaPAC will wait to receive a call accept packet before clearing the call.
OBJECT-TYPE    
  INTEGER 2..200  

ctrlParamErrorThreshold 1.3.6.1.4.1.397.3.4.1.23
Error Threshold. The number of CRC errors that will be accepted before generating an error report.
OBJECT-TYPE    
  INTEGER 1..250  

ctrlParamLoopBarPriority 1.3.6.1.4.1.397.3.4.1.24
Loop Bar Priority. Prevents calls from looping on the same controller.
OBJECT-TYPE    
  INTEGER 0..15  

ctrlParamExtendedCallMgmt 1.3.6.1.4.1.397.3.4.1.25
Extended Call Management. Invokes extended packet processing facilities via the MAC file.
OBJECT-TYPE    
  INTEGER in(2), out(3), in-out(4), v25b(5), v25m(13), none(1)  

ctrlParamOptionalTimers 1.3.6.1.4.1.397.3.4.1.26
Optional Timers. Optional level 3 timers for clearing calls when a clear confirmation has not been received after a clear request has been sent. T13 is used if the controller is set to be a logical DCE and the timeout will be 60 seconds. T23 is used if the controller is a logical DTE and the timeout is 180 seconds.
OBJECT-TYPE    
  INTEGER t13(2), t23(3), none(1)  

ctrlParamOptionalFlags 1.3.6.1.4.1.397.3.4.1.27
Optional Flags. This parameter is used to insert extra flags between frames to slow down the rate of transmission. It will only take effect on controllers with a sub-type of XIO.
OBJECT-TYPE    
  INTEGER 0..60  

ctrlParamTransportLevelType 1.3.6.1.4.1.397.3.4.1.28
Transport Level Type. Enable the ISO transport facility.
OBJECT-TYPE    
  INTEGER iso(34), none(1)  

ctrlParamTransportClass 1.3.6.1.4.1.397.3.4.1.29
Transport Class. The type of transport class implemented.
OBJECT-TYPE    
  INTEGER class3(49), class2(33), class0(1)  

ctrlParamDefaultWindowSize 1.3.6.1.4.1.397.3.4.1.30
Default Window Size. The initial credit limit to be used on a transport session.
OBJECT-TYPE    
  INTEGER 0..7  

ctrlParamDisableFlowControl 1.3.6.1.4.1.397.3.4.1.31
Disable Flow Control. Enable/disable flow control on a tranport class 2 call.
OBJECT-TYPE    
  INTEGER yes(2), no(1)  

ctrlParamTSAPFormat 1.3.6.1.4.1.397.3.4.1.32
TSAP Format. Determines how the TSAP's will be treated internally by the MegaPAC. If set to text the local and remote TSAP's will be converted to form a 4 character internal resource name. If set to hex the first two hexadecimal pairs will form the resource name.
OBJECT-TYPE    
  INTEGER text(2), hex(1)  

ctrlParamMaximumTPDUSize 1.3.6.1.4.1.397.3.4.1.33
Max. TPDU Size. The maximum Transport Protocol Data Unit Size.
OBJECT-TYPE    
  INTEGER bytes-1024(11), bytes-512(10), bytes-256(9), bytes128(8), bytes-128(1)  

ctrlParamTTRTime 1.3.6.1.4.1.397.3.4.1.34
TTR Timer. Time To Resynchronise. Specifies the time delay in seconds for the transport class three timer to resync at the initiating end.
OBJECT-TYPE    
  INTEGER 0..120  

ctrlParamTWRTime 1.3.6.1.4.1.397.3.4.1.35
TWR Timer. Time to Wait for Resynchronisation. The time delay in seconds allowed for the transport class 3 timer at the responding end to wait for resynchronisation, before clearing down the transport session.
OBJECT-TYPE    
  INTEGER 0..120  

ctrlParamDestinationAddress 1.3.6.1.4.1.397.3.4.1.36
Destination Address. The physical address of the target device.
OBJECT-TYPE    
  DisplayString  

ctrlParamDSAP 1.3.6.1.4.1.397.3.4.1.37
DSAP. The Destination Service Access Point.
OBJECT-TYPE    
  INTEGER 2..254  

ctrlParamSSAP 1.3.6.1.4.1.397.3.4.1.38
SSAP. The Source Service Access Point.
OBJECT-TYPE    
  INTEGER 2..254  

ctrlParamSDLCOptions 1.3.6.1.4.1.397.3.4.1.39
SDLC Options. A range of link level options used for establishing IBM connections.
OBJECT-TYPE    
  INTEGER none(1), pu4(33), wait(65), xid(129), idle(17), wait-xid(193)  

ctrlParamPrimaryStation 1.3.6.1.4.1.397.3.4.1.40
Primary Station. This parameter determines whether the MegaPAC will operate as a HOST primary connection (yes) or a CLUSTER secondary connection (no).
OBJECT-TYPE    
  INTEGER yes(2), no(1)  

ctrlParamIdleDetectTime 1.3.6.1.4.1.397.3.4.1.41
Idle Detect Timer. This parameter determines the time period in tenths of a second before an unacknowleged POLL/RESPONSE frame will be retransmitted.
OBJECT-TYPE    
  INTEGER 0..100  

ctrlParamPollInterval 1.3.6.1.4.1.397.3.4.1.42
Poll Interval. The time period in tenths of a second between sending POLL frames.
OBJECT-TYPE    
  INTEGER 0..100  

ctrlParamDuplex 1.3.6.1.4.1.397.3.4.1.43
Duplex. Enables SDLC full duplex operation, half duplex operation is reserved for future use.
OBJECT-TYPE    
  INTEGER full(1), half(2)  

ctrlParamTransmitDelay 1.3.6.1.4.1.397.3.4.1.44
Transmit Delay. Determines the time period in tenths of a second between the MegaPAC receiving an RR frame with the P-Bit set and the MegaPAC issuing an RR response with the F-Bit set.
OBJECT-TYPE    
  INTEGER 0..20  

ctrlParamSlowPollTimer 1.3.6.1.4.1.397.3.4.1.45
Slow Poll Timer. When the controller has been defined as a primary station a slow poll rate can be specified for polling a Cluster controller that is down. This is to avoid causing delays to working Cluster controllers in a multi-point mode. The value is specified in tenths of a second.
OBJECT-TYPE    
  INTEGER 0..255  

ctrlParamMaxCallInterval 1.3.6.1.4.1.397.3.4.1.46
Max. Call Interval. When controller is configured as a primary station, a call request retry interval may be defined, so as to avoid the situation where successive call requests are continuously generated to the network. The initial call interval is 2 seconds, this interval is progressively doubled until the Maximum Call Interval (defined in minutes) is reached.
OBJECT-TYPE    
  INTEGER 0..20  

ctrlParamMaxCallCycles 1.3.6.1.4.1.397.3.4.1.47
Max. Call Cycles. This parameter is used in conjunction with the Maximum Call Interval parameter. It specifies the maximum number of call request cycles that can take effect before call requests continue at the Maximum Call Interval parameter setting. Each cycle consisting of call requests being initiated at intervals in incrementing multiples of two seconds, up to the Maximum Call Interval parameter.
OBJECT-TYPE    
  INTEGER 0..255  

ctrlParamGroupPoll 1.3.6.1.4.1.397.3.4.1.48
Group Poll. Used in SNA applications, where the specified value would generate multiple down-stream poll requests.
OBJECT-TYPE    
  INTEGER 0..255  

ctrlParamDelayToRTSLow 1.3.6.1.4.1.397.3.4.1.49
Delay RTS Low. Specifies the number of padding characters to be inserted between the end of data transmission and the dropping of the RTS signal. Only required for synchronous operation.
OBJECT-TYPE    
  INTEGER 0..256  

ctrlParamDelayToCTSHigh 1.3.6.1.4.1.397.3.4.1.50
Delay CTS High. Specifies the number of padding characters to be inserted between the dropping of RTS and the raising of CTS. Only required for synchronous operation.
OBJECT-TYPE    
  INTEGER 0..256  

ctrlParamInputSyncDeletion 1.3.6.1.4.1.397.3.4.1.51
Input Sync Deletion. If set, all SYNC characters will be stripped prior to transmission. Only effective in synchronous full duplex mode.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ctrlParamOutputSyncInsertion 1.3.6.1.4.1.397.3.4.1.52
Output Sync Insertion. Specifies the number of SYNC characters to be transmitted prior to the start of the data block. Only effective in synchronous operation.
OBJECT-TYPE    
  INTEGER 0..255  

ctrlParamDCDFilter 1.3.6.1.4.1.397.3.4.1.53
DCD Filter. A filter delay specified in tenths of a second which prevents unwanted link restarts caused by toggling of DCD signal.
OBJECT-TYPE    
  INTEGER 0..20  

ctrlParamInhibitTimeFill 1.3.6.1.4.1.397.3.4.1.54
Inhibit Time Fill Allows the insertion of time fill frames to compensate for network delays. Effective in synchronous mode only.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ctrlParamDirectedBroadcasts 1.3.6.1.4.1.397.3.4.1.55
Directed Broadcasts.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ctrlParamDefaultLocalPrinter 1.3.6.1.4.1.397.3.4.1.56
Default Local Printer. The number of the channel which is reserved for a Screen Print server, a value of (0) disables the Screen Print facility.
OBJECT-TYPE    
  INTEGER 0..128  

ctrlParamNewLANInterface 1.3.6.1.4.1.397.3.4.1.57
New FRM Port. This controller marks the first position of a controller connection to a LAN interface. All other controllers defined as NewPhysicalInterface/ No will map to the same interface defined as NewPhysicalInterface/ Yes.
OBJECT-TYPE    
  INTEGER no(2), yes(1)  

ctrlParamNewSerialInterface 1.3.6.1.4.1.397.3.4.1.58
New FRM Port. This controller marks the first position of a controller connection to a serial interface. All other controllers defined as NewPhysicalInterface/ No will map to the same interface defined as NewPhysicalInterface/ Yes.
OBJECT-TYPE    
  INTEGER yes(2), no(1)  

ctrlParamDlci 1.3.6.1.4.1.397.3.4.1.59
Defines the DLCI PVC number
OBJECT-TYPE    
  INTEGER 1..1022  

ctrlParamMode 1.3.6.1.4.1.397.3.4.1.60
Defines a Network to Network Inteface (NNI) or User Network Interface (UNI) implementation. Where MegaPAC connects to a Frame Realy switch, this parameter just be defined as DTE i.e. a UNI, otherwise when connecting operating as a switch, NNI i.e. DCE operation must be specified. All controllers mapped to the same physical interface must be configured the same mode setting
OBJECT-TYPE    
  INTEGER dte(1), dce(2), nni(129)  

ctrlParamLmi 1.3.6.1.4.1.397.3.4.1.61
Local Management Inteface (LMI). Ansi = ANSI LMI yes = T1.S1 LMI no = LMI disabled.
OBJECT-TYPE    
  INTEGER ansi(129), yes(2), no(1)  

ctrlParamKeepAliveTimer 1.3.6.1.4.1.397.3.4.1.62
Only applicable if the LMI is active. Specifies in seconds the interval between keep alive messages. If this end is a DTE, this is the actual interval between Status Requests generated to the DCE. If this end is a DCE, then the timer is used simply to detect whether connection to the DTE has been lost. Note: it is the DTE which is the active partner across the LMI interface, in accordance with the LMI specification.
OBJECT-TYPE    
  INTEGER 2..80  

ctrlParamStatusEnquiryInterval 1.3.6.1.4.1.397.3.4.1.63
Frame Relay : Specifies how often a DTE sends a or a DCE expects a Full Status Request message. The number specified is the ratio between Status Requets messages, and Full Status Request enquiries. For example, if the value 10 is specified, and this end is a DTE, then every 10th status request would include a full status request (in the above example every 100 seconds).
OBJECT-TYPE    
  INTEGER 0..100  

ctrlParamBandwidth 1.3.6.1.4.1.397.3.4.1.64
The sample period used in enforcing the committed information rate (CIR). The CIR expressed in terms of characters per 1/10 th second. There are two further parameters which appear directly after the BANDWIDTH/ prompt which are designed to handle bursty traffic (i.e. Bc and Be).
OBJECT-TYPE    
  INTEGER 0..32767  

ctrlParamBurstCommit 1.3.6.1.4.1.397.3.4.1.65
Burst Commit, i.e. the number of characters the remote end is committed to buffering, in our case in a 1/10th of a second period
OBJECT-TYPE    
  INTEGER 0..32767  

ctrlParamBurstEligibility 1.3.6.1.4.1.397.3.4.1.66
Burst Eligibility, i.e the DLCI in question is enabled to transmit a burst beyond its committed information rate, when enabled to do so by the state of the other DLCIs. The figure given is again with respect to a 1/10th second period, and the maximum data rate when the DLCI is enabled to transmit at its burst rate is given by the equation ; Maximum data rate = CIR(1+Be/Bc) It should be noted that on DLCIs which are carrying data of a non-bursty nature (e.g voice traffic), the Be should be configured as zero (thereby telling the MegaPAC that it is carrying traffic of a non-bursty nature.) Secondly, if the Bc value is configured as zero, the MegaPAC uses a default sample period of 1 second.
OBJECT-TYPE    
  INTEGER 0..32767  

channel 1.3.6.1.4.1.397.4
OBJECT IDENTIFIER    

chanNumberConfigured 1.3.6.1.4.1.397.4.1
Number of channels. The number of channels configured.
OBJECT-TYPE    
  INTEGER  

chanStatTable 1.3.6.1.4.1.397.4.2
A table of channels associated with a controller.
OBJECT-TYPE    
  SEQUENCE OF  
    ChanStatEntry

chanStatEntry 1.3.6.1.4.1.397.4.2.1
An individual channel entry.
OBJECT-TYPE    
  ChanStatEntry  

chanStatIndex 1.3.6.1.4.1.397.4.2.1.1
Index. The position of this channel in the controller channel Table.
OBJECT-TYPE    
  INTEGER  

chanStatName 1.3.6.1.4.1.397.4.2.1.2
Name. A user defined name for routing calls to this channel.
OBJECT-TYPE    
  DisplayString SIZE(4)  

chanStatControllerIndex 1.3.6.1.4.1.397.4.2.1.3
Controller Index. The index to the controller that this channel operates within.
OBJECT-TYPE    
  INTEGER  

chanStatNameCtrlName 1.3.6.1.4.1.397.4.2.1.4
Controller Name. The controller NAME supporting this channel
OBJECT-TYPE    
  DisplayString SIZE(4)  

chanStatConnectedToChannelIndex 1.3.6.1.4.1.397.4.2.1.5
Connected to Index. The INDEX of the CHANNEL that this channel is connected to.
OBJECT-TYPE    
  INTEGER  

chanStatState 1.3.6.1.4.1.397.4.2.1.6
State. The current Status of the channel, the status may be one or a combination of the following: disc Disconnected. emul Channel in Terminal Emulation mode. emul Channel in Terminal Emulation mode. post Processing data before forwarding e.g. LF insert in async. busy Temporarily unavailable. call Outgoing channel making call. data Data transfer, call in progress. wake Outgoing channel transmitting. setup Incoming channel waiting outgoing channel call setup. rout Incoming channel waiting assignment of outgoing channel. addr Incoming channel waiting resource selection. name Incoming channel is processing a users password. look Incoming channel is looking-up a users password name. serv Service selection mode awaiting resource code NAME. pass Incoming channel is processing a users password. rung Ring Indicator MUX PORT only.
OBJECT-TYPE    
  INTEGER disc(1), emul(73), emul(69), post(57), busy(49), call(45), data(41), wake(37), setup(33), rout(29), addr(25), name(21), look(17), serv(13), pass(9), rung(5)  

chanStatSessionStatus 1.3.6.1.4.1.397.4.2.1.7
Session Status. The Status of the channel during a call session, the status may be one or a combination of the following: State Description CALL Call Originator. DRI Flow controlling input. DRO Flow controlling on output. TRAN Presentation service not involved in call set-up. QUEU Queued to selected resource. STAT Awaiting queue status information. PAD In PAD Recall mode. DISC Data buffers draining before clearing call.
OBJECT-TYPE    
  INTEGER none(1), tran(2), dri(3), dro(5), call(9), pad(17), queu(33), stat(65), call-tran(10), call-tran-dri(13), disc(129)  

chanStatEIA 1.3.6.1.4.1.397.4.2.1.8
EIA Displays the status of the V24/V28 signals on term or muxport links, or call status on X.25 links. The down state indicates that level 2 is inactive.
OBJECT-TYPE    
  INTEGER none(1), dcd(2), ring(3), x28(5), rej(9), iso(17), tcal(33), closed(65), down(129)  

chanStatTotalFramesIn 1.3.6.1.4.1.397.4.2.1.9
Total Frames In. The total number of frames received on this channel since it entered Data State.
OBJECT-TYPE    
  Counter  

chanStatTotalFramesOut 1.3.6.1.4.1.397.4.2.1.10
Total Frames out. The total number of frames transmitted on this channel since it entered Data State.
OBJECT-TYPE    
  Counter  

chanStatTotalCharsIn 1.3.6.1.4.1.397.4.2.1.11
Total Characters In. The total number of characters received on this channel since it entered Data State.
OBJECT-TYPE    
  Counter  

chanStatTotalCharsOut 1.3.6.1.4.1.397.4.2.1.12
Total Characters Out. The total number of characters transmitted on this channel since it entered Data State.
OBJECT-TYPE    
  Counter  

chanStatTxWindow 1.3.6.1.4.1.397.4.2.1.13
Tx Window. The Level 3 Transmit Window size.
OBJECT-TYPE    
  INTEGER  

chanStatRxWindow 1.3.6.1.4.1.397.4.2.1.14
Rx Window. The Level 3 Receive Window size.
OBJECT-TYPE    
  INTEGER  

chanStatTxSize 1.3.6.1.4.1.397.4.2.1.15
Tx Size. The maximum size for outgoing packets.
OBJECT-TYPE    
  INTEGER  

chanStatRxSize 1.3.6.1.4.1.397.4.2.1.16
Rx Size. The maximum acceptable size for incoming packets.
OBJECT-TYPE    
  INTEGER  

chanStatCause 1.3.6.1.4.1.397.4.2.1.17
Cause. The value of the cause code in the last Clear Packet received or transmitted (decimal).
OBJECT-TYPE    
  INTEGER  

chanStatDiagnostic 1.3.6.1.4.1.397.4.2.1.18
Diagnostic. The value of the diagnostic code in the last Clear Packet received or transmitted (decimal).
OBJECT-TYPE    
  INTEGER  

chanStatResetCause 1.3.6.1.4.1.397.4.2.1.19
Reset Cause. The value of the last reset code in the last RESET packet transmitted.
OBJECT-TYPE    
  INTEGER  

chanStatResetDiagnostic 1.3.6.1.4.1.397.4.2.1.20
Reset Diagnostic. The value of the last diagnostic code in the last RESET packet transmitted.
OBJECT-TYPE    
  INTEGER  

chanStatResetCauseReceived 1.3.6.1.4.1.397.4.2.1.21
Reset Cause Received. The value of the last reset code in the last RESET packet received.
OBJECT-TYPE    
  INTEGER  

chanStatResetDiagReceived 1.3.6.1.4.1.397.4.2.1.22
Reset Diagnostic Received. The value of the last diagnostic code in the last RESET packet received.
OBJECT-TYPE    
  INTEGER  

chanStatLevel3State 1.3.6.1.4.1.397.4.2.1.23
Level 3 State. The level 3 status of the channel.
OBJECT-TYPE    
  INTEGER disc(1), rest(3), call(5), data(7), cls(9), clr(11), reset(13)  

chanStatCallPriority 1.3.6.1.4.1.397.4.2.1.24
Call Priority. Call and Resource priorities are used primarily for providing alternate routing. For a call to succeed the Call Priority on the incoming channel must be greater than or equal to the Resource Priority on the outgoing channel.
OBJECT-TYPE    
  INTEGER  

chanStatResourcePriority 1.3.6.1.4.1.397.4.2.1.25
Resource Priority See chanCallPriority above.
OBJECT-TYPE    
  INTEGER  

chanStatPadEnable 1.3.6.1.4.1.397.4.2.1.26
PAD Enable. The value of this statistic reflects the setting as configured on the channel.
OBJECT-TYPE    
  INTEGER disable(1), enable(2), rev(3), enable-rev(4), prof(5), enable-prof(6), mask(17), enable-mask(18), x28(34)  

chanStatPortMatch 1.3.6.1.4.1.397.4.2.1.27
Port Match. The TCP port that is connected
OBJECT-TYPE    
  INTEGER no(1), srce(2), dest(129), wild(137)  

chanStatPrimaryStation 1.3.6.1.4.1.397.4.2.1.28
Primary Station. Determines whether the MegaPAC port is functioning as a Primary or Secondary SDLC station.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

chanStatSDLCState 1.3.6.1.4.1.397.4.2.1.29
SDLC State. The State of the SDLC connection, may be one of the following: State Description ACTIVE The SNRM and UA commands have been sent successfully. If primary, the P-Bit has not been sent (i.e. has not been polled). If secondary, the P-Bit has not been received (has got F-Bit and not been polled again). DISC Primary station only. Either a 'STOP' command has been issued for the port, or a QDISC command has been received from the network. The MegaPAC will be sending an SDLC DISC command with the P-Bit set. POLL If primary, the MegaPAC has sent a frame with the P-Bit (has polled). If secondary, the MegaPAC has received the P-Bit (has been polled). SNRM Only for primary stations. The MegaPAC has sent a SNRM, but has not received a UA.
OBJECT-TYPE    
  INTEGER idle(1), snrm(3), active(5), poll(7), disc(9)  

chanStatQLLCState 1.3.6.1.4.1.397.4.2.1.30
QLLC State. The State of the QLLC connection, may be one of the following: State Description CLSD The MegaPAC has received a QDISC and sent a QUA on the network. This sets the DISC state on the SDLC port. CLSI The MegaPAC has sent a QDISC and is waiting for a QUA. FRMR The MegaPAC has received a QFRMR from the network. INOP The SVC is down. OPEN The VC is running. QSM and QUA have been sent and received. OPNI The MegaPAC has sent a QSM and is awaiting a QUA.
OBJECT-TYPE    
  INTEGER inop(1), clsd(5), openi(9), frmr(13), clsi(17), open(21)  

chanStatSDLCTransmitState 1.3.6.1.4.1.397.4.2.1.31
SDLC Transmit State. May be one of the following: State Description NORM The MegaPAC is allowed to transmit data. NULL The MegaPAC is not allowed to transmit data. RNR The MegaPAC has received an RNR. RTRY The MegaPAC is in the retransmission state.
OBJECT-TYPE    
  INTEGER idle(1), norm(3), rtry(7), rnr(11)  

chanStatPolls 1.3.6.1.4.1.397.4.2.1.32
Polls. The quantity of polls that have occured since the link was established
OBJECT-TYPE    
  INTEGER  

chanStatStationAddress 1.3.6.1.4.1.397.4.2.1.33
Station Address. The IBM PU poll address
OBJECT-TYPE    
  INTEGER  

chanStatXIDIdentification 1.3.6.1.4.1.397.4.2.1.34
XID Identification. This field contains the first 64 bytes of the XID that has been used.
OBJECT-TYPE    
  DisplayString  

chanStatTries 1.3.6.1.4.1.397.4.2.1.35
Tries. The number of times the current command has been transmitted.
OBJECT-TYPE    
  INTEGER  

chanStatWindow 1.3.6.1.4.1.397.4.2.1.36
KLevel 2. The level 2 window size.
OBJECT-TYPE    
  INTEGER  

chanStatLUActive 1.3.6.1.4.1.397.4.2.1.37
LU Active. If set to YES then the MegaPAC Logical Unit has responded positively to an ACTLU command. If set to NO the MegaPAC has either not received or has responded negatively to an ACTLU command.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

chanStatBindActive 1.3.6.1.4.1.397.4.2.1.38
Bind Active. If set to YES then the MegaPAC Logical Unit has responded positively to a BIND command. If set to NO the MegaPAC has either not received or has responded negatively to a BIND command.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

chanStatLUType 1.3.6.1.4.1.397.4.2.1.39
LU Type. The Session type taken from the BIND command. It may be one of the following: Session Type Description 0 User defined applications. 1 Printer. 2 Full Screen 3270 applications. 3 Older type printers.
OBJECT-TYPE    
  INTEGER 0..3  

chanStatBreaksReceived 1.3.6.1.4.1.397.4.2.1.40
Breaks Rx The number of Break characters received from the terminal.
OBJECT-TYPE    
  Counter  

chanStatFramingErrors 1.3.6.1.4.1.397.4.2.1.41
Framing Errors. The number of characters received with no stop bit appended. The MegaPAC substitutes a '#' character in place of each framing error.
OBJECT-TYPE    
  Counter  

chanStatInputOverruns 1.3.6.1.4.1.397.4.2.1.42
Input Overruns. The number of times that data has been discarded due to a lack of receive buffers.
OBJECT-TYPE    
  Counter  

chanStatParityErrors 1.3.6.1.4.1.397.4.2.1.43
TParity Errors. he number of parity errors received on this channel.
OBJECT-TYPE    
  Counter  

chanStatTerminalType 1.3.6.1.4.1.397.4.2.1.44
Terminal Type. The type of emulation to be applied to the TERM controller, it may be one or more of the following: Type comment ASYN ASCII data support SYNC Bi-sync data support MINI Minitel terminal support HP H.P ENQ / ACK async protocol support X28 X28 command syntax (English) X28F X28 command syntax (French) ANSI Async ASCII Terminal support VPAD Viewdata PAD Emulation support MTRM MegaTerm PC Emulation support BUF Used for Buffer PVC call set-ups TPAD ACAB30 transaction card terminal support VT22 Async VT220Terminal support
OBJECT-TYPE    
  INTEGER async(2), sync(3), hp(225), x28(209), x28f(999), ansi(177), ext-ansi(161), vpad(129), mtrm(113), slip(97), buf(81), tpad(65), vt220(41)  

chanStatCircuitType 1.3.6.1.4.1.397.4.2.1.45
Circuit Type. The type of circuit used on this channel, it may be one or more of the following:
OBJECT-TYPE    
  INTEGER call(2), call-stat(66), call-pvc(10), call-pvc-stat(74), out(17), out-stat(81), out-pvc(25), out-pvc-stat(89), osi-call(6), osi-call-stat(70), osi-call-pvc(14), osi-call-pvc-stat(78), osi-out(21), osi-out-stat(85), osi-out-pvc(29), osi-out-pvc-stat(93), osi-call-svc(38), osi-call-svc-stat(102), osi-out-svc(53), osi-out-svc-stat(117), svc(33), svc-stat(97), queue(4)  

chanStatOptions 1.3.6.1.4.1.397.4.2.1.46
The option(s) which have been envoked on this channel, one or more of:
OBJECT-TYPE    
  INTEGER none(1), rts(2), idle(3), busy(5), hold(9), nbrk(17), arps(65), iso(129), pass(257), bill(513), msgs(1025), gate(2049), name(4097), talk(8193), x28(16385), supr(32769)  

chanStatBuffers 1.3.6.1.4.1.397.4.2.1.47
Buffers. The number of data buffers to be used as a threshold value before flow control to the terminal is invoked.
OBJECT-TYPE    
  INTEGER  

chanStatDiscMode 1.3.6.1.4.1.397.4.2.1.48
Disc mode. Specifies the call disconnect character that may be applied having established a route via the presentation service.
OBJECT-TYPE    
  INTEGER  

chanStatMenuNumber 1.3.6.1.4.1.397.4.2.1.49
Menu Number. Specifies which menu will be displayed to the user by the presentation service.
OBJECT-TYPE    
  INTEGER  

chanStatHelpNumber 1.3.6.1.4.1.397.4.2.1.50
Help Number. Specifies which help menu will be displayed to the user by the presentation service.
OBJECT-TYPE    
  INTEGER  

chanStatNewsNumber 1.3.6.1.4.1.397.4.2.1.51
News Number. The Menu number that will be displayed if an outgoing resource is unavailable.
OBJECT-TYPE    
  INTEGER  

chanStatPadRecall 1.3.6.1.4.1.397.4.2.1.52
Pad Recall. This parameter allows the user to escape from the data transfer state to the PAD command state. The permitted values are: 0 No PAD recall 1 Escape character is ^P 2 - 126 The decimal value specified is the escape character
OBJECT-TYPE    
  INTEGER  

chanStatEcho 1.3.6.1.4.1.397.4.2.1.53
Echo. Determines whether 'echo' is enabled or disabled. If set to controlled, the echo facility is controlled by the operator.
OBJECT-TYPE    
  INTEGER enable(2), disable(1)  

chanStatDataForwarding 1.3.6.1.4.1.397.4.2.1.54
Data Forwarding. This parameter controls which character or characters cause the accumulated data to be forwarded. The possible values may be added together to forward on one of a number of conditions. The allowable values are: 0 Forward only on buffer full. 128 Forward on graphics characters. 64 Forward on all characters in columns 0 and 1 of the International Alphabet No. 5. 1 Forward on A-Z, a-z and 0-9. 2 Forward on Carriage Return. 4 Forward on ESC, BEL, ENQ, ACK. 8 Forward on DEL, CAN, DC2. 16 Forward on EXT, EOT. 32 Forward on HT, LF, VT, FF.
OBJECT-TYPE    
  INTEGER  

chanStatDelay 1.3.6.1.4.1.397.4.2.1.55
Delay. Specifies the idle time in tenths of a second, allowable between successive characters before the accumulated data is forwarded. A value of 0 disables the timeout facility.
OBJECT-TYPE    
  INTEGER  

chanStatDRI 1.3.6.1.4.1.397.4.2.1.56
DRI. Flow control of terminal by the MegaPAC. Valid settings are: enabled MegaPAC flow controls terminal using XON/XOFF. cts MegaPAC flow controls terminal using CTS. init+enable MegaPAC sends XON automatically on initialisation. disable No flow control.
OBJECT-TYPE    
  INTEGER enabled(2), rts(33), cts(129), init-enable(65), disabled(1)  

chanStatPadSignals 1.3.6.1.4.1.397.4.2.1.57
Pad Signals. Enable X.28 prompts and/or messages to be displayed on the users terminal.
OBJECT-TYPE    
  INTEGER enable(2), disable(1)  

chanStatBreak 1.3.6.1.4.1.397.4.2.1.58
Break. The Action the MegaPAC will take on receipt of a Break Signal. The valid values are: 0 When the MegaPAC receives a Break Signal from the terminal no action is taken. 1 When the MegaPAC receives a Break Signal from the terminal it will transmit an INTERRUPT packet. 2 When the MegaPAC receives a Break Signal from the terminal it will transmit an RESET packet. 5 When the MegaPAC receives a Break Signal from the terminal it will transmit an INTERRUPT packet and an indication of Break PAD message. 8 When the MegaPAC receives a Break Signal from the terminal it will escape from data transfer state. 21 When the MegaPAC receives a Break Signal from the terminal it will transmit an INTERRUPT packet and an indication of Break PAD message, while setting (X3) parameter (8) to the value 1 (discard any data received from the network).
OBJECT-TYPE    
  INTEGER  

chanStatPadding 1.3.6.1.4.1.397.4.2.1.59
Padding. The number of NULL characters inserted after a carriage return.
OBJECT-TYPE    
  INTEGER  

chanStatFold 1.3.6.1.4.1.397.4.2.1.60
Fold The number of characters output before line folding occurs. Setting to 0 disables line folding.
OBJECT-TYPE    
  INTEGER  

chanStatDRO 1.3.6.1.4.1.397.4.2.1.61
Data Restraint Out.
OBJECT-TYPE    
  INTEGER enabled(2), cts(129), init-enable(65), disabled(1)  

chanStatLFI 1.3.6.1.4.1.397.4.2.1.62
LFI. This parameter controls linefeed insertion after a carriage return. The valid seetings are: 0 Line feed insertion disabled. 1 A linefeed is inserted after a carriage return, in the data forwarded to the terminal. 4 A linefeed is sent to the terminal after echo of a carriage return to the terminal. 5 As defined by values 1 + 4. 6 Linefeed inserted after carriage return from terminal and each carriage return echoed to the terminal. 7 As defined by values 1 + 6.
OBJECT-TYPE    
  INTEGER  

chanStatLFPad 1.3.6.1.4.1.397.4.2.1.63
LFPad. The number of NULL padding characters sent to a device following a linefeed character.
OBJECT-TYPE    
  INTEGER  

chanStatEdit 1.3.6.1.4.1.397.4.2.1.64
Edit. Controls editing of text in data transfer state.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

chanStatCharDel 1.3.6.1.4.1.397.4.2.1.65
Char Del. The keystroke used for deleting a character.
OBJECT-TYPE    
  INTEGER  

chanStatBufferDel 1.3.6.1.4.1.397.4.2.1.66
Buffer Del. The keystroke used for deleting the buffer.
OBJECT-TYPE    
  INTEGER  

chanStatDisp 1.3.6.1.4.1.397.4.2.1.67
Disp The keystroke used to redisplay the data in the buffer.
OBJECT-TYPE    
  INTEGER  

chanStatEditServiceSignals 1.3.6.1.4.1.397.4.2.1.68
Edit Service Signals. This parameter enables the user to edit the PAD service signals (echoing). The valid settings are: 0 No editing PAD service signals are echoed. 1 A '\' will be echoed for each character deleted. 2 A 'BS' character will be echoed for each character deleted. 8 and 32-126 Specifies the decimal value of the ASCII character to be echoed for each character deleted.
OBJECT-TYPE    
  INTEGER  

chanStatEchoMask 1.3.6.1.4.1.397.4.2.1.69
Echo Mask. This parameter controls the characters which should not be echoed. The valid settings are: 0 All characters should be echoed to the terminal. 1 do not echo carriage return. 2 do not echo linefeed. 4 do not echo VT, HT and FF characters. 8 do not echo BEL and BS character. 16 do not echo ESC and ENQ. 32 do not echo ACK, NAK, STX, SOH, EOT, ETB or ETX. 64 do not echo editing characters as defined by parameters 16, 17 and 18. 128 do not echo other control characters and DEL.
OBJECT-TYPE    
  INTEGER  

chanStatParityTreatment 1.3.6.1.4.1.397.4.2.1.70
Parity Treatment. Determines the parity generation and checking performed valid settings are: 0 No parity generation or checking. 1 Check parity. 2 Generate parity. 3 Check and generate parity.
OBJECT-TYPE    
  INTEGER  

chanStatPageWait 1.3.6.1.4.1.397.4.2.1.71
PageWait. Specifies the number of lines to be transmitted, after which the MegaPAC will wait until instructed by the user to continue sending data (by entering Q). A value of 0 disables the page wait facility.
OBJECT-TYPE    
  INTEGER  

chanStatForce 1.3.6.1.4.1.397.4.2.1.72
Forward Char. The ASCII character which will force data forwarding, 0 disables forced data forwarding.
OBJECT-TYPE    
  INTEGER  

chanStatBreakChar 1.3.6.1.4.1.397.4.2.1.73
Break Char. The ASCII character in decimal which is used to simulate a BREAK signal.
OBJECT-TYPE    
  INTEGER  

chanStatNetworkParity 1.3.6.1.4.1.397.4.2.1.74
Network Parity. With the Terminal type set to ASYN+X28, the parity can be forced onto the network side by selecting the approriate value.
OBJECT-TYPE    
  INTEGER even(1), odd(2), mark(4), space(8), none(5)  

chanStatEscapeDelay 1.3.6.1.4.1.397.4.2.1.75
Escape Delay. Specifies the time in tenths of a second, that after receiving an ESC character, all characters are buffered before being forwarded. During this time the ECHO facility is turned off, and is only restored when the delay timer has expired.
OBJECT-TYPE    
  INTEGER  

chanStatDestTsap 1.3.6.1.4.1.397.4.2.1.76
Destination TSAP The destination Transport Service Access Point.
OBJECT-TYPE    
  DisplayString SIZE(4)  

chanStatTransportLevelState 1.3.6.1.4.1.397.4.2.1.77
Transport Level State. Transport Class 4 session statistics
OBJECT-TYPE    
  INTEGER disc(1), call(3), init(5), data(7), cls(9), clr(11)  

chanStatLinkState 1.3.6.1.4.1.397.4.2.1.78
Link State. The current state of the Link Control Protocol
OBJECT-TYPE    
  INTEGER open(15), acks(13), ackr(11), reqs(9), stpi(7), clsi(5), stop(3), clos(1)  

chanStatProtocolState 1.3.6.1.4.1.397.4.2.1.79
Protocol State. The current state of the Protocol Control Protocol
OBJECT-TYPE    
  INTEGER open(15), acks(13), ackr(11), reqs(9), stpi(7), clsi(5), stop(3), clos(1)  

chanStatProtocol 1.3.6.1.4.1.397.4.2.1.80
Protocol Displays the protocol configured for the channel
OBJECT-TYPE    
  INTEGER ip(32802), ipx(32812)  

chanStatIdentity 1.3.6.1.4.1.397.4.2.1.81
Identity. The current value of the IDENTITY field being put into the Link Control Protocol or Protocol Control Protocol commands.
OBJECT-TYPE    
  INTEGER  

chanStatDlciRxDe 1.3.6.1.4.1.397.4.2.1.82
DLCI RX Count. The total number of Frames with the DE bit set received on this channel since it entered Data State.
OBJECT-TYPE    
  Counter  

chanStatDlciTxDe 1.3.6.1.4.1.397.4.2.1.83
DLCI TX Count. The total number of Frames with the DE bit set transmitted on this channel since it entered Data State.
OBJECT-TYPE    
  Counter  

chanStatDlciRxFecn 1.3.6.1.4.1.397.4.2.1.84
DLCI RX Fecn Count. The total number of Fecns (Forward Explicit Congestion Notification) received on this channel since active.
OBJECT-TYPE    
  Counter  

chanStatDlciTxFecn 1.3.6.1.4.1.397.4.2.1.85
DLCI TX Fecn Count. The total number of Fecns (Forward Explicit Congestion Notification) transmitted on this channel since active.
OBJECT-TYPE    
  Counter  

chanStatDlciRxBecn 1.3.6.1.4.1.397.4.2.1.86
DLCI RX Becn Count. The total number of Becns (Backwards Explicit Congestion Notification) received on this channel since active.
OBJECT-TYPE    
  Counter  

chanStatDlciTxBecn 1.3.6.1.4.1.397.4.2.1.87
DLCI TX Becn Count. The total number of Becns (Backwards Explicit Congestion Notification) transmitted on this channel since active.
OBJECT-TYPE    
  Counter  

chanStatConnectedToControllerIndex 1.3.6.1.4.1.397.4.2.1.88
Connected to Index. The INDEX of the CONTROLLER that this channel is connected to.
OBJECT-TYPE    
  INTEGER  

chanParamTable 1.3.6.1.4.1.397.4.3
A table of channels associated with this Level 2 controller.
OBJECT-TYPE    
  SEQUENCE OF  
    ChanParamEntry

chanParamEntry 1.3.6.1.4.1.397.4.3.1
An individual Channel.
OBJECT-TYPE    
  ChanParamEntry  

chanParamIndex 1.3.6.1.4.1.397.4.3.1.1
Index. The position of this channel in the controller channel Table.
OBJECT-TYPE    
  INTEGER  

chanParamName 1.3.6.1.4.1.397.4.3.1.2
Name. A user defined name for routing calls to this channel.
OBJECT-TYPE    
  DisplayString SIZE(4)  

chanParamDRCMask 1.3.6.1.4.1.397.4.3.1.3
DRC Mask. A four character string used to force expicit routing to the named resource.
OBJECT-TYPE    
  DisplayString SIZE(4)  

chanParamTerminalType 1.3.6.1.4.1.397.4.3.1.4
Terminal Type. If the channel is to perform terminal emulation, then the setting defined will be specific to the users terminal envoking emulation.
OBJECT-TYPE    
  INTEGER async(2), sync(3), hp(225), x28(209), x28f(999), ansi(177), ext-ansi(161), vpad(129), mtrm(113), slip(97), buf(81), tpad(65), vt220(41)  

chanParamCircuitType 1.3.6.1.4.1.397.4.3.1.5
Circuit Type. The type of circuit used on this channel
OBJECT-TYPE    
  INTEGER call(2), call-stat(66), call-pvc(10), call-pvc-stat(74), out(17), out-stat(81), out-pvc(25), out-pvc-stat(89), osi-call(6), osi-call-stat(70), osi-call-pvc(14), osi-call-pvc-stat(78), osi-out(21), osi-out-stat(85), osi-out-pvc(29), osi-out-pvc-stat(93), osi-call-svc(38), osi-call-svc-stat(102), osi-out-svc(53), osi-out-svc-stat(117), svc(33), svc-stat(97), queue(4)  

chanParamOptions 1.3.6.1.4.1.397.4.3.1.6
Options. A range of channel options, these options may be specified individually or added together.
OBJECT-TYPE    
  INTEGER none(1), msgs(1025), msgs-name(5121), msgs-name-talk(13313), msgs-pass(1281), msgs-pass-gate(3329), msgs-name-pass(5377), msgs-name-pass-talk(13569), msgs-name-pass-talk-gate(15617), pass(257), bill(513), gate(2049), name(4097), x28(16385), talk(8193), supr(32769), arps(65), diag(33), iso(129), rts(2), idle(3), busy(5), hold(9), nbrk(17)  

chanParamBuffers 1.3.6.1.4.1.397.4.3.1.7
Buffers. The number of system buffers allocated to this channel for incoming calls.
OBJECT-TYPE    
  INTEGER 1..240  

chanParamDiscMode 1.3.6.1.4.1.397.4.3.1.8
DISC Mode. The number of the character in decimal which forces disconnection of the call.
OBJECT-TYPE    
  INTEGER 0..32  

chanParamMenuNumber 1.3.6.1.4.1.397.4.3.1.9
Menu Number. Specifies which menu will be displayed to the user by the presentation service
OBJECT-TYPE    
  INTEGER 0..32  

chanParamHelpNumber 1.3.6.1.4.1.397.4.3.1.10
Help Number. Specifies which help screen will be displayed to the user by the presentation service.
OBJECT-TYPE    
  INTEGER 0..32  

chanParamNewsNumber 1.3.6.1.4.1.397.4.3.1.11
News Number. The number of the menu which will be displayed if an outgoing channel is unavailable.
OBJECT-TYPE    
  INTEGER 0..32  

chanParamCallPriority 1.3.6.1.4.1.397.4.3.1.12
Call Priority. Call and Resource priorities are used primarily for providing alternate routing. For a call to succeed the Call Priority on the incoming channel must be greater than or equal to the Resource Priority on the outgoing channel.
OBJECT-TYPE    
  INTEGER 0..15  

chanParamResourcePriority 1.3.6.1.4.1.397.4.3.1.13
Resource Priority. Call and Resource priorities are used primarily for providing alternate routing. For a call to succeed the Call Priority on the incoming channel must be greater than or equal to the Resource Priority on the outgoing channel.
OBJECT-TYPE    
  INTEGER 0..15  

chanParamPadEnable 1.3.6.1.4.1.397.4.3.1.14
Pad Enable. The effect of the PAD Enable parameters are as follows: enable PAD services enabled. The logical channel will respond to X.29 packets. enable-rev REVerse PAD enabled. When a call is established to this channel, the MegaPAC will generate an X.29 qualified data packet back to the caller, containing the X.3 operating values specified in the channel's configuration. enable-prof The X.3 profile settings for the channel will be derived by referencing the logical channel's NAME/ parameter to the NAME/ field in the PROF file. The X.3 settings as contained in the PROF file record are then loaded onto the channel.
OBJECT-TYPE    
  INTEGER disable(1), enable(2), rev(3), enable-rev(4), prof(5), enable-prof(6), mask(17), enable-mask(18), x28(34)  

chanParamPadRecall 1.3.6.1.4.1.397.4.3.1.15
Pad Recall (1). This parameter allows the user to escape from the data transfer state to the PAD command state. The permitted values are: 0 No PAD recall 1 Escape character is ^P 2 - 126 The decimal value specified is the escape character
OBJECT-TYPE    
  INTEGER 0..126  

chanParamEcho 1.3.6.1.4.1.397.4.3.1.16
Echo. Determines whether 'echo' is enabled or disabled. If set to controlled, the echo facility is controlled by the operator.
OBJECT-TYPE    
  INTEGER enable(2), disable(1)  

chanParamDataForwarding 1.3.6.1.4.1.397.4.3.1.17
Data Forwarding. This parameter controls which character or characters cause the accumulated data to be forwarded. The possible values may be added together to forward on one of a number of conditions. The allowable values are: 0 Forward only on buffer full. 128 Forward on graphics characters. 64 Forward on all characters in columns 0 and 1 of the International Alphabet No. 5. 1 Forward on A-Z, a-z and 0-9. 2 Forward on Carriage Return. 4 Forward on ESC, BEL, ENQ, ACK. 8 Forward on DEL, CAN, DC2. 16 Forward on EXT, EOT. 32 Forward on HT, LF, VT, FF.
OBJECT-TYPE    
  INTEGER  

chanParamDelay 1.3.6.1.4.1.397.4.3.1.18
Delay. Specifies the idle time in tenths of a second, allowable between successive characters before the accumulated data is forwarded. A value of 0 disables the timeout facility.
OBJECT-TYPE    
  INTEGER 0..255  

chanParamDRI 1.3.6.1.4.1.397.4.3.1.19
DRI. Flow control of terminal by the MegaPAC. Valid settings are: enabled MegaPAC flow controls terminal using XON/XOFF. cts MegaPAC flow controls terminal using CTS. init+enable MegaPAC sends XON automatically on initialisation. disable No flow control.
OBJECT-TYPE    
  INTEGER enabled(2), rts(33), cts(129), init-enable(65), disabled(1)  

chanParamPadSignals 1.3.6.1.4.1.397.4.3.1.20
Pad Signals. Enable X.28 prompts and/or messages to be displayed on the users terminal.
OBJECT-TYPE    
  INTEGER enable(2), disable(1)  

chanParamBreak 1.3.6.1.4.1.397.4.3.1.21
Break. The Action the MegaPAC will take on receipt of a Break Signal. The valid values are: 0 When the MegaPAC receives a Break Signal from the terminal no action is taken. 1 When the MegaPAC receives a Break Signal from the terminal it will transmit an INTERRUPT packet. 2 When the MegaPAC receives a Break Signal from the terminal it will transmit an RESET packet. 5 When the MegaPAC receives a Break Signal from the terminal it will transmit an INTERRUPT packet and an indication of Break PAD message. 8 When the MegaPAC receives a Break Signal from the terminal it will escape from data transfer state. 21 When the MegaPAC receives a Break Signal from the terminal it will transmit an INTERRUPT packet and an indication of Break PAD message, while setting (X3) parameter (8) to the value 1 (discard any data received from the network).
OBJECT-TYPE    
  INTEGER  

chanParamPadding 1.3.6.1.4.1.397.4.3.1.22
Padding. The number of NULL characters inserted after a carriage return.
OBJECT-TYPE    
  INTEGER 0..255  

chanParamFold 1.3.6.1.4.1.397.4.3.1.23
Fold. The number of characters output before line folding occurs. Setting to 0 disables line folding.
OBJECT-TYPE    
  INTEGER 0..255  

chanParamDRO 1.3.6.1.4.1.397.4.3.1.24
Data Restraint Out.
OBJECT-TYPE    
  INTEGER enabled(2), cts(129), init-enable(65), disabled(1)  

chanParamLFI 1.3.6.1.4.1.397.4.3.1.25
LFI. This parameter controls linefeed insertion after a carriage return. The valid settings are: 0 Line feed insertion disabled. 1 A linefeed is inserted after a carriage return, in the data forwarded to the terminal. 4 A linefeed is sent to the terminal after echo of a carriage return to the terminal. 5 As defined by values 1 + 4. 6 Linefeed inserted after carriage return from terminal and each carriage return echoed to the terminal. 7 As defined by values 1 + 6.
OBJECT-TYPE    
  INTEGER  

chanParamLFPad 1.3.6.1.4.1.397.4.3.1.26
LFPad. The number of NULL padding characters sent to a device following a linefeed character.
OBJECT-TYPE    
  INTEGER 0..7  

chanParamEdit 1.3.6.1.4.1.397.4.3.1.27
Edit. Controls editing of text in data transfer state.
OBJECT-TYPE    
  INTEGER enable(2), disable(1)  

chanParamCharDel 1.3.6.1.4.1.397.4.3.1.28
Char Delete. The keystroke used for deleting a character.
OBJECT-TYPE    
  INTEGER 0..128  

chanParamBufferDel 1.3.6.1.4.1.397.4.3.1.29
Buffer Delete. The keystroke used for deleting the buffer.
OBJECT-TYPE    
  INTEGER 0..127  

chanParamDisp 1.3.6.1.4.1.397.4.3.1.30
Disp. The keystroke used to redisplay the data in the buffer.
OBJECT-TYPE    
  INTEGER 0..127  

chanParamEditServiceSignals 1.3.6.1.4.1.397.4.3.1.31
Edit Service Signals. This parameter enables the user to edit the PAD service signals (echoing). The valid settings are: 0 No editing PAD service signals are echoed. 1 A '\' will be echoed for each character deleted. 2 A 'BS' character will be echoed for each character deleted. 8 and 32-126 Specifies the decimal value of the ASCII character to be echoed for each character deleted.
OBJECT-TYPE    
  INTEGER 0..126  

chanParamEchoMask 1.3.6.1.4.1.397.4.3.1.32
Echo Mask. This parameter controls the characters which should not be echoed. The valid settings are: 0 All characters should be echoed to the terminal. 1 do not echo carriage return. 2 do not echo linefeed. 4 do not echo VT, HT and FF characters. 8 do not echo BEL and BS character. 16 do not echo ESC and ENQ. 32 do not echo ACK, NAK, STX, SOH, EOT, ETB or ETX. 64 do not echo editing characters as defined by parameters 16, 17 and 18. 128 do not echo other control characters and DEL.
OBJECT-TYPE    
  INTEGER  

chanParamParityTreatment 1.3.6.1.4.1.397.4.3.1.33
Parity Treatment. Determines the parity generation and checking performed valid settings are: 0 No parity generation or checking. 1 Check parity. 2 Generate parity. 3 Check and generate parity.
OBJECT-TYPE    
  INTEGER 0..3  

chanParamPageWait 1.3.6.1.4.1.397.4.3.1.34
Page Wait. Specifies the number of lines to be transmitted, after which the MegaPAC will wait until instructed by the user to continue sending data (by entering Q). A value of 0 disables the page wait facility.
OBJECT-TYPE    
  INTEGER 0..255  

chanParamForce 1.3.6.1.4.1.397.4.3.1.35
Force. The ASCII character which will force data forwarding, 0 disables forced data forwarding.
OBJECT-TYPE    
  INTEGER 0..255  

chanParamBreakChar 1.3.6.1.4.1.397.4.3.1.36
Break Character. The ASCII character in decimal which is used to simulate a BREAK signal.
OBJECT-TYPE    
  INTEGER 0..32  

chanParamNetworkParity 1.3.6.1.4.1.397.4.3.1.37
Network Parity. With the Terminal type set to ASYN+X28, the parity can be forced onto the network side by selecting the approriate value.
OBJECT-TYPE    
  INTEGER even(1), odd(2), mark(4), space(8), none(5)  

chanParamEscapeDelay 1.3.6.1.4.1.397.4.3.1.38
Escape Delay. Specifies the time in tenths of a second, that after receiving an ESC character, all characters are buffered before being forwarded. During this time the ECHO facility is turned off, and is only restored when the delay timer has expired.
OBJECT-TYPE    
  INTEGER 0..15  

chanParamStationAddress 1.3.6.1.4.1.397.4.3.1.39
Station Address. Physical Unit Address of the Cluster Controller.
OBJECT-TYPE    
  INTEGER 0..255  

chanParamProvideXID 1.3.6.1.4.1.397.4.3.1.40
Provide XID.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

chanParamMode 1.3.6.1.4.1.397.4.3.1.41
Mode. This parameter provides a number of additional connection facilities for channels on virtual controllers.
OBJECT-TYPE    
  INTEGER none(1), path(2), push(3), pull(5), stop(9), auto(17), auto-pull-path-push-stop(32), sym(33), data(65), wait(81), hub(97), resp(129), sat(193)  

chanParamPortMatch 1.3.6.1.4.1.397.4.3.1.42
Port Match. This parameter optionally allows the Source and Destination ports to be used in conjunction with the IP address for routing.
OBJECT-TYPE    
  INTEGER no(1), source(2), destination(129), wild(137)  

chanParamReverseTelnetPort 1.3.6.1.4.1.397.4.3.1.43
Reverse Telnet Port. The port number which will respond to TELNET open requests. The default value for TELNET ports is '23'.
OBJECT-TYPE    
  INTEGER 0..32767  

chanParamBroadcastFilterTimer 1.3.6.1.4.1.397.4.3.1.44
Broadcast Filter Timer.
OBJECT-TYPE    
  INTEGER 0..12000  

chanParamInhibitLearning 1.3.6.1.4.1.397.4.3.1.45
Inhibit Learning. This parameter determines whether the 'bridge' will work in Directed or Learning mode. If InhibitLearning is set to 'Yes' then the bridge will only forward frames whose addresses are fixed in the forwarding table.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

chanParamRetainSession 1.3.6.1.4.1.397.4.3.1.46
Retain Session. This parameter determines if and how a session will be cleared down when the call is cleared. The parameter is only applicable to channels (2) to (n). If set to NOTIFY or NO the session will be cleared when the call disconnects , NOTIFY will cause a NOTIFY RU to be sent indicating the disconnection. If this parameter is set to YES then the session will be retained on channel disconnection, this is used to provide a hot key switching facility.
OBJECT-TYPE    
  INTEGER notify(1), yes(2), no(3)  

chanParamPrinterType 1.3.6.1.4.1.397.4.3.1.47
Printer Type. If set to IBM the logical channel will act as an appication system printer, otherwise it operates in screen emulation mode. Only applicable to channels (2) to (n).
OBJECT-TYPE    
  INTEGER ibm(1), none(2)  

chanParamScreenPrinter 1.3.6.1.4.1.397.4.3.1.48
Screen Printer. If set to YES, screen printer requests are to be processed and sent to this LU address (in this mode, the terminal attaching to this channel MUST have a printer attached). If set to NO, screen printing is supported via the LOCAL PRINTER or the DEFAULT LOCAL PRINTER parameters.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

chanParamLocalPrinter 1.3.6.1.4.1.397.4.3.1.49
Local Printer. This parameter specifies the channel to which screen printing should be directed. It takes precedence over the value defined by the DEFAULT LOCAL PRINTER at controller level. This parameter may only be applied to channels (2) to (n).
OBJECT-TYPE    
  INTEGER 0..128  

chanParamInterlockBind 1.3.6.1.4.1.397.4.3.1.50
Interlock Bind. This parameter is only applicable to channels (2) to (n). When set to YES, an UNBIND request will be sent to the host upon disconnecting. Note: when used in cojunction with a 4 character DRC mask, this setting will invoke a call set-up when a BIND is received. This setting is often used when sending a file transfer accross a Public Network.
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

chanParamRedirectPrintTo 1.3.6.1.4.1.397.4.3.1.51
Redirect Printer To. This parameter is only applicable to channels (2) to (n). If set to (0), then no redirection takes place. Otherwise, LU type 1 session data is output to the nominated logical channel, each block being preceeded by the escape sequence to switch to the auxiliary port, and followed by the sequence to switch it back to the screen again. This is useful in several environments, Foe example, using two LU channels it enables a terminal user to interact with the Host, and receive Host system prints at the same terminal (supporting a printer).
OBJECT-TYPE    
  INTEGER 0..128  

chanParamLUBase 1.3.6.1.4.1.397.4.3.1.52
First LU defined by up-stream host.
OBJECT-TYPE    
  INTEGER 0..4095  

chanParamLUOffset 1.3.6.1.4.1.397.4.3.1.53
LU Offset.
OBJECT-TYPE    
  INTEGER 0..4095  

chanParamLUTotal 1.3.6.1.4.1.397.4.3.1.54
Total number of LUs to be allocated to down- stream PU's.
OBJECT-TYPE    
  INTEGER 0..4095  

chanParamDlciBase 1.3.6.1.4.1.397.4.3.1.55
The channel DLCI address.
OBJECT-TYPE    
  INTEGER 0..1023  

chanParamDlciAdjacentBase 1.3.6.1.4.1.397.4.3.1.56
The DLCI number on the cross connected port in the MegaPAC used when groups of channels are being switched across the MegaPAC. Used in conjunction with the DRC mask.
OBJECT-TYPE    
  INTEGER 0..1023  

chanParamDlciPriority 1.3.6.1.4.1.397.4.3.1.57
A value from 0 to 32 indicating the relative priority of this DLCI to the other data streams on this trunk, i.e. other DLCIs. The higher the value the higher the priority.
OBJECT-TYPE    
  INTEGER 0..32  

chanParamDlciATM 1.3.6.1.4.1.397.4.3.1.58
Determines whether fragmentation should be implemented on frames on this link.
OBJECT-TYPE    
  INTEGER off(1), on(2), all(129)  

chanParamDlciCir 1.3.6.1.4.1.397.4.3.1.59
The committed information rate for this DLCI - the units are in 80bits/sec
OBJECT-TYPE    
  INTEGER 0..32767  

chanParamDlciBc 1.3.6.1.4.1.397.4.3.1.60
Bc(Burst Commit) - the committed burst that the MegaPAC will allow to be transmitted on this DLCI; the units are 80bits.
OBJECT-TYPE    
  INTEGER 0..32767  

chanParamDlciBe 1.3.6.1.4.1.397.4.3.1.61
Be(Burst Excess) is the excess above the Bc that will be transmitted to the line by the MegaPAC in any given Tc. The units are 80bits.
OBJECT-TYPE    
  INTEGER 0..32767  

chanParamDlciDe 1.3.6.1.4.1.397.4.3.1.62
DE(Discard Eligibility) when set will indicate that in a congested situation this frame should be discarded first.
OBJECT-TYPE    
  INTEGER off(1), on(2), all(129)  

chanParamDlciProtocol 1.3.6.1.4.1.397.4.3.1.63
Specifies header in RFC 1480/1490 connections
OBJECT-TYPE    
  INTEGER none(1), ip(2), ipx(4), iso(8), fragment(16), sna(32)  

chanParamDlciDsap 1.3.6.1.4.1.397.4.3.1.64
Used in RFC 1490 SNA connections - each SAP identifies a specific PU, hence by using different SAPs, multiple PUs can be multiplexed on the same Frame Relay PVC
OBJECT-TYPE    
  INTEGER 0..254  

chanParamDlciSsap 1.3.6.1.4.1.397.4.3.1.65
Used in RFC 1490 SNA connections - each SAP identifies a specific PU, hence by using different SAPs, multiple PUs can be multiplexed on the same Frame Relay PVC
OBJECT-TYPE    
  INTEGER 0..254  

chanParamDlciPutype 1.3.6.1.4.1.397.4.3.1.66
Used in RFC 1490 SNA connections - specifies type 2.0 or 2.1
OBJECT-TYPE    
  INTEGER 0..4095  

x25File 1.3.6.1.4.1.397.5
OBJECT IDENTIFIER    

x25FileSize 1.3.6.1.4.1.397.5.1
X25 file size. The number of entries configured into the X25 file.
OBJECT-TYPE    
  INTEGER  

x25Table 1.3.6.1.4.1.397.5.2
A table of X.25 routing entries
OBJECT-TYPE    
  SEQUENCE OF  
    X25Entry

x25Entry 1.3.6.1.4.1.397.5.2.1
OBJECT-TYPE    
  X25Entry  

x25Index 1.3.6.1.4.1.397.5.2.1.1
Index. The index to an individual X.25 entry
OBJECT-TYPE    
  INTEGER  

x25Name 1.3.6.1.4.1.397.5.2.1.2
Name. A 4 character name which is used to match on the 'NAME' parameter of the channel on which a call will be routed over the X.25 network.
OBJECT-TYPE    
  DisplayString SIZE(4)  

x25AddressGroup 1.3.6.1.4.1.397.5.2.1.3
Address Group. An integer used to partition the X.25 routing tables. Any match on a channel name will only take effect if the channel 'AddressGroup' parameter is set to the same value.
OBJECT-TYPE    
  INTEGER 0..15  

x25Address 1.3.6.1.4.1.397.5.2.1.4
Address. The numeric address which is used to match on the incoming X.25 address in a call request packet.
OBJECT-TYPE    
  DisplayString SIZE(0..16)  

x25UserData 1.3.6.1.4.1.397.5.2.1.5
User Data A text field in which Call User Data or Facilities may be placed. The user data will be inserted into call request packets generated by the MegaPAC.
OBJECT-TYPE    
  DisplayString SIZE(0..30)  

nameFile 1.3.6.1.4.1.397.6
OBJECT IDENTIFIER    

nameFileSize 1.3.6.1.4.1.397.6.1
Name File Size. The number of entries configured into the NAME file.
OBJECT-TYPE    
  INTEGER  

nameTable 1.3.6.1.4.1.397.6.2
A table of 'Name' entries.
OBJECT-TYPE    
  SEQUENCE OF  
    NameEntry

nameEntry 1.3.6.1.4.1.397.6.2.1
OBJECT-TYPE    
  NameEntry  

nameIndex 1.3.6.1.4.1.397.6.2.1.1
Index. The index into the name table.
OBJECT-TYPE    
  INTEGER  

nameName 1.3.6.1.4.1.397.6.2.1.2
Name. A string of up to 8 characters in length which is typed in by the network user in order to establish a connection to a specific resource.
OBJECT-TYPE    
  DisplayString SIZE(0..8)  

nameDRCMask 1.3.6.1.4.1.397.6.2.1.3
DRC Mask. The four character resource (channel) name to which the call will be directed.
OBJECT-TYPE    
  DisplayString SIZE(4)  

nameCallPriority 1.3.6.1.4.1.397.6.2.1.4
Call Priority. The internal call priority which will be assigned to the call.
OBJECT-TYPE    
  INTEGER 0..15  

nameBilling 1.3.6.1.4.1.397.6.2.1.5
Billing If enabled, statistics relating to the call will be sent to the billing file.
OBJECT-TYPE    
  INTEGER enabled(2), disabled(1)  

nameOptions 1.3.6.1.4.1.397.6.2.1.6
Options Enables the appropriate terminal emulation options.
OBJECT-TYPE    
  INTEGER none(1), iso(2), pap(17), ppp(33), pap-ppp(59), prof(5), icl7661(9), teln(65), rev-teln(129)  

passFile 1.3.6.1.4.1.397.7
OBJECT IDENTIFIER    

passFileSize 1.3.6.1.4.1.397.7.1
Pass File Size. The number of entries configured into the PASSWORD file.
OBJECT-TYPE    
  INTEGER  

macFile 1.3.6.1.4.1.397.8
OBJECT IDENTIFIER    

macFileSize 1.3.6.1.4.1.397.8.1
Mac File Size. The number of entries configured into the MAC file.
OBJECT-TYPE    
  INTEGER  

macTable 1.3.6.1.4.1.397.8.2
A table of MAC entries
OBJECT-TYPE    
  SEQUENCE OF  
    MacEntry

macEntry 1.3.6.1.4.1.397.8.2.1
OBJECT-TYPE    
  MacEntry  

macIndex 1.3.6.1.4.1.397.8.2.1.1
Index. An index to an individual entry in the MAC table.
OBJECT-TYPE    
  INTEGER  

macName 1.3.6.1.4.1.397.8.2.1.2
Name. The level 2 controller name to which this entry applies.
OBJECT-TYPE    
  DisplayString SIZE(4)  

macFunction 1.3.6.1.4.1.397.8.2.1.3
Function. The function field determines what action should be taken if their is a match on this entry.
OBJECT-TYPE    
  INTEGER nop(1), cad(2), dad(3), cud(4), else(5), fac(6), inse(16386), dele(16387), copy(16388), posn(16389), mark(16390), data(16391), eof(16392), ibeg(32769), iend(32770), obeg(32771), oend(32772), pu(32773), xid(32774), list(32775), mask(32776), sync(32777), tab(32778), rout(32781), nvmt(32782), add(32783), bar(32784)  

macOptions 1.3.6.1.4.1.397.8.2.1.4
Options. Specific actions that may be envoked in conjunction with the function field.
OBJECT-TYPE    
  INTEGER none(1), not(129), trap(33), flag(17), copy(9), jump(32769), expe(16385), iso-1980(8193), bill(4097), talk(2049), thru(5), cad(3), y13(65), iso(2), tcal(1025), rej(513), tlat(257), iso-expe(16386), iso-y13(66)  

macSelector 1.3.6.1.4.1.397.8.2.1.5
Selector. This field can contain a string of between 0 and 32 Hexadecimal characters, that must be matched by the Function DAD, CAD, CUD or FAC.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

macGenerator 1.3.6.1.4.1.397.8.2.1.6
Generator. This field can contain a string of between 0 and 32 Hexadecimal characters, and can have different purposes depending on the Function or Options fields.
OBJECT-TYPE    
  DisplayString SIZE(0..32)  

ilanFile 1.3.6.1.4.1.397.9
OBJECT IDENTIFIER    

ilanFileSize 1.3.6.1.4.1.397.9.1
Ilan File Size. The number of entries configured into the ILAN file.
OBJECT-TYPE    
  INTEGER  

ilanTable 1.3.6.1.4.1.397.9.2
A table of ILAN entries
OBJECT-TYPE    
  SEQUENCE OF  
    IlanEntry

ilanEntry 1.3.6.1.4.1.397.9.2.1
OBJECT-TYPE    
  IlanEntry  

ilanIndex 1.3.6.1.4.1.397.9.2.1.1
Index. An index to an individual entry in the ILAN table.
OBJECT-TYPE    
  INTEGER  

ilanName 1.3.6.1.4.1.397.9.2.1.2
Name. The Resource which this entry applies to.
OBJECT-TYPE    
  DisplayString SIZE(4)  

ilanOptions 1.3.6.1.4.1.397.9.2.1.3
Options ISO Allows transport calls to be set up on the outgoing channel. EXPE Allows expedited data to be sent.
OBJECT-TYPE    
  INTEGER none(1), y13(17), talk(9), dbit(5), iso(2), iso-expe(4), iso-y13(18)  

ilanEthernetAddress 1.3.6.1.4.1.397.9.2.1.4
Ethernet Address. The destination MAC address of the named host.
OBJECT-TYPE    
  DisplayString SIZE(12)  

ilanTSAP 1.3.6.1.4.1.397.9.2.1.5
TSAP. The Transport Service Access Point required on the destination Host.
OBJECT-TYPE    
  DisplayString SIZE(0..20)  

elogFile 1.3.6.1.4.1.397.10
OBJECT IDENTIFIER    

elogFileSize 1.3.6.1.4.1.397.10.1
Elog File Size. The size of the error log file.
OBJECT-TYPE    
  INTEGER  

elogTable 1.3.6.1.4.1.397.10.2
A table of Error Log entries.
OBJECT-TYPE    
  SEQUENCE OF  
    ElogEntry

elogEntry 1.3.6.1.4.1.397.10.2.1
OBJECT-TYPE    
  ElogEntry  

elogIndex 1.3.6.1.4.1.397.10.2.1.1
Index. The index to an Error Log entry.
OBJECT-TYPE    
  INTEGER  

elogRecord 1.3.6.1.4.1.397.10.2.1.2
Record. The Error Log entry in ascii format.
OBJECT-TYPE    
  DisplayString SIZE(128)  

configChange 1.3.6.1.4.1.397.32
Enterprise Specific trap for MegaPAC Configuration Change.
TRAP-TYPE    
  elogRecord  

vcpConnect 1.3.6.1.4.1.397.33
Enterprise Specific trap for MegaPAC VCP Connect.
TRAP-TYPE    
  elogRecord  

vcpDisconnect 1.3.6.1.4.1.397.34
Enterprise Specific trap for MegaPAC VCP Disconnect.
TRAP-TYPE    
  elogRecord  

billThreshReached 1.3.6.1.4.1.397.35
Enterprise Specific trap for MegaPAC- threshold reached for No. of BILLING records outstanding.
TRAP-TYPE    
  elogRecord  

linkNoResponse 1.3.6.1.4.1.397.96
Enterprise Specific trap for MegaPAC Link Not Responding.
TRAP-TYPE    
  elogRecord  

linkCarrierLoss 1.3.6.1.4.1.397.97
Enterprise Specific trap for MegaPAC Link Carrier Loss.
TRAP-TYPE    
  elogRecord  

linkAddressErr 1.3.6.1.4.1.397.98
Enterprise Specific trap for MegaPAC Link Address Error.
TRAP-TYPE    
  elogRecord  

frameLessThan2 1.3.6.1.4.1.397.99
Enterprise Specific trap for MegaPAC Link Frame < 2 BYTES.
TRAP-TYPE    
  elogRecord  

ifieldTooLarge 1.3.6.1.4.1.397.100
Enterprise Specific trap for MegaPAC Link I-Field too Large.
TRAP-TYPE    
  elogRecord  

linkRestart 1.3.6.1.4.1.397.103
Enterprise Specific trap for MegaPAC Link restart.
TRAP-TYPE    
  elogRecord  

linkBlocked 1.3.6.1.4.1.397.104
Enterprise Specific trap for MegaPAC LINK BLOCKED (Flow controlled).
TRAP-TYPE    
  elogRecord  

linkDisconnect 1.3.6.1.4.1.397.105
Enterprise Specific trap for MegaPAC Link Disconnected.
TRAP-TYPE    
  elogRecord  

linkFrmrRecvd 1.3.6.1.4.1.397.112
Enterprise Specific trap for MegaPAC Link FRMR received.
TRAP-TYPE    
  elogRecord  

linkDmResponse 1.3.6.1.4.1.397.113
Enterprise Specific trap for MegaPAC Link DM response.
TRAP-TYPE    
  elogRecord  

linkBadNr 1.3.6.1.4.1.397.114
Enterprise Specific trap for MegaPAC Link Bad N(r).
TRAP-TYPE    
  elogRecord  

linkDown 1.3.6.1.4.1.397.115
Enterprise Specific trap for MegaPAC Link Down.
TRAP-TYPE    
  elogRecord  

linkFrmrSent 1.3.6.1.4.1.397.116
Enterprise Specific trap for MegaPAC Link FRMR sent.
TRAP-TYPE    
  elogRecord  

crcThreshExceeded 1.3.6.1.4.1.397.117
Enterprise Specific trap for MegaPAC CRC Threshold Exceeded.
TRAP-TYPE    
  elogRecord  

linkManRestart 1.3.6.1.4.1.397.121
Enterprise Specific trap for MegaPAC Link Manual restart.
TRAP-TYPE    
  elogRecord  

testIndicationResponse 1.3.6.1.4.1.397.122
Enterprise Specific trap for MegaPAC 'TEST' command Indication/Response.
TRAP-TYPE    
  elogRecord  

interfaceFailure 1.3.6.1.4.1.397.123
Enterprise Specific trap for MegaPAC Inteface (e.g. chip) failure.
TRAP-TYPE    
  elogRecord  

xidComRecvd 1.3.6.1.4.1.397.124
Enterprise Specific trap for MegaPAC XID command received.
TRAP-TYPE    
  elogRecord  

bufferOverrun 1.3.6.1.4.1.397.166
Enterprise Specific trap for MegaPAC Buffer Overrun Error.
TRAP-TYPE    
  elogRecord  

connectTimeWarn 1.3.6.1.4.1.397.200
Enterprise Specific trap for MegaPAC Connect Time Warning.
TRAP-TYPE    
  elogRecord  

isdnNameAssigned 1.3.6.1.4.1.397.230
Enterprise Specific trap for MegaPAC ISDN/V25 bis Name Assigned.
TRAP-TYPE    
  elogRecord  

isdnNameDeAassigned 1.3.6.1.4.1.397.231
Enterprise Specific trap for MegaPAC ISDN/V25 bis Name De-Assigned.
TRAP-TYPE    
  elogRecord  

Defined Objects

CtrlStatEntry  
SEQUENCE    
  INTEGER as ctrlStatIndex  
  DisplayString as ctrlStatName  
  INTEGER as ctrlStatType  
  INTEGER as ctrlStatSubType  
  INTEGER as ctrlStatNumberChannels  
  INTEGER as ctrlStatFirstChannelIndex  
  Counter as ctrlStatCRCErrors  
  Counter as ctrlStatTotalCallSetUps  
  INTEGER as ctrlStatCurrentCalls  
  Counter as ctrlStatDataIn  
  Counter as ctrlStatDataOut  
  Counter as ctrlStatDataFramesIn  
  Counter as ctrlStatDataFramesOut  
  INTEGER as ctrlStatDataFrameRateIn  
  INTEGER as ctrlStatDataFrameRateOut  
  Counter as ctrlStatCallsReceived  
  Counter as ctrlStatCallsSent  
  Counter as ctrlStatClearsReceived  
  Counter as ctrlStatRetransmissions  
  Counter as ctrlStatRejects  
  INTEGER as ctrlStatState  
  INTEGER as ctrlStatSubState  
  Counter as ctrlStatNoTries  
  INTEGER as ctrlStatOptions  
  INTEGER as ctrlStatLCGN  
  Counter as ctrlStatResetsReceived  
  Counter as ctrlStatInterruptsReceived  
  INTEGER as ctrlStatOuputQueueLength  
  DisplayString as ctrlStatStationAddress  
  DisplayString as ctrlStatDestinationAddress  
  DisplayString as ctrlStatEIA  
  INTEGER as ctrlStatSdlcOptions  
  INTEGER as ctrlStatArpRequestRec  
  INTEGER as ctrlStatArpRequestSent  
  INTEGER as ctrlStatArpResponsesRec  
  INTEGER as ctrlStatTestType  
  INTEGER as ctrlStatTestSet  
  INTEGER as ctrlStatTest  
  INTEGER as ctrlStatLstate  
  INTEGER as ctrlStatRstate  

CtrlParamEntry  
SEQUENCE    
  INTEGER as ctrlParamIndex  
  DisplayString as ctrlParamName  
  INTEGER as ctrlParamType  
  INTEGER as ctrlParamSubType  
  INTEGER as ctrlParamNoChannels  
  INTEGER as ctrlParamSpeed  
  INTEGER as ctrlParamInterfaceType  
  INTEGER as ctrlParamPacketSize  
  INTEGER as ctrlParamV54Modem  
  INTEGER as ctrlParamAddress  
  INTEGER as ctrlParamOptions  
  INTEGER as ctrlParamInitFrame  
  INTEGER as ctrlParamT1  
  INTEGER as ctrlParamTries  
  INTEGER as ctrlParamKLevel2  
  INTEGER as ctrlParamKLevel3  
  INTEGER as ctrlParamLineGroup  
  INTEGER as ctrlParamLCGN  
  INTEGER as ctrlParamLCNOffset  
  INTEGER as ctrlParamAddressGroup  
  INTEGER as ctrlParamFrameSequence  
  INTEGER as ctrlParamCallTimeOut  
  INTEGER as ctrlParamErrorThreshold  
  INTEGER as ctrlParamLoopBarPriority  
  INTEGER as ctrlParamExtendedCallMgmt  
  INTEGER as ctrlParamOptionalTimers  
  INTEGER as ctrlParamOptionalFlags  
  INTEGER as ctrlParamTransportLevelType  
  INTEGER as ctrlParamTransportClass  
  INTEGER as ctrlParamDefaultWindowSize  
  INTEGER as ctrlParamDisableFlowControl  
  INTEGER as ctrlParamTSAPFormat  
  INTEGER as ctrlParamMaximumTPDUSize  
  INTEGER as ctrlParamTTRTime  
  INTEGER as ctrlParamTWRTime  
  DisplayString as ctrlParamDestinationAddress  
  INTEGER as ctrlParamDSAP  
  INTEGER as ctrlParamSSAP  
  INTEGER as ctrlParamSDLCOptions  
  INTEGER as ctrlParamPrimaryStation  
  INTEGER as ctrlParamIdleDetectTime  
  INTEGER as ctrlParamPollInterval  
  INTEGER as ctrlParamDuplex  
  INTEGER as ctrlParamTransmitDelay  
  INTEGER as ctrlParamSlowPollTimer  
  INTEGER as ctrlParamMaxCallInterval  
  INTEGER as ctrlParamMaxCallCycles  
  INTEGER as ctrlParamGroupPoll  
  INTEGER as ctrlParamDelayToRTSLow  
  INTEGER as ctrlParamDelayToCTSHigh  
  INTEGER as ctrlParamInputSyncDeletion  
  INTEGER as ctrlParamOutputSyncInsertion  
  INTEGER as ctrlParamDCDFilter  
  INTEGER as ctrlParamInhibitTimeFill  
  INTEGER as ctrlParamDirectedBroadcasts  
  INTEGER as ctrlParamDefaultLocalPrinter  
  INTEGER as ctrlParamNewLANInterface  
  INTEGER as ctrlParamNewSerialInterface  
  INTEGER as ctrlParamDlci  
  INTEGER as ctrlParamMode  
  INTEGER as ctrlParamLmi  
  INTEGER as ctrlParamKeepAliveTimer  
  INTEGER as ctrlParamStatusEnquiryInterval  
  INTEGER as ctrlParamBandwidth  
  INTEGER as ctrlParamBurstCommit  
  INTEGER as ctrlParamBurstEligibility  

ChanStatEntry  
SEQUENCE    
  INTEGER as chanStatIndex  
  DisplayString as chanStatName  
  INTEGER as chanStatControllerIndex  
  DisplayString as chanStatNameCtrlName  
  INTEGER as chanStatConnectedToChannelIndex  
  INTEGER as chanStatState  
  INTEGER as chanStatSessionStatus  
  INTEGER as chanStatEIA  
  Counter as chanStatTotalFramesIn  
  Counter as chanStatTotalFramesOut  
  Counter as chanStatTotalCharsIn  
  Counter as chanStatTotalCharsOut  
  INTEGER as chanStatTxWindow  
  INTEGER as chanStatRxWindow  
  INTEGER as chanStatTxSize  
  INTEGER as chanStatRxSize  
  INTEGER as chanStatCause  
  INTEGER as chanStatDiagnostic  
  INTEGER as chanStatResetCause  
  INTEGER as chanStatResetDiagnostic  
  INTEGER as chanStatResetCauseReceived  
  INTEGER as chanStatResetDiagReceived  
  INTEGER as chanStatLevel3State  
  INTEGER as chanStatCallPriority  
  INTEGER as chanStatResourcePriority  
  INTEGER as chanStatPadEnable  
  INTEGER as chanStatPortMatch  
  INTEGER as chanStatPrimaryStation  
  INTEGER as chanStatSDLCState  
  INTEGER as chanStatQLLCState  
  INTEGER as chanStatSDLCTransmitState  
  INTEGER as chanStatPolls  
  INTEGER as chanStatStationAddress  
  DisplayString as chanStatXIDIdentification  
  INTEGER as chanStatTries  
  INTEGER as chanStatWindow  
  INTEGER as chanStatLUActive  
  INTEGER as chanStatBindActive  
  INTEGER as chanStatLUType  
  Counter as chanStatBreaksReceived  
  Counter as chanStatFramingErrors  
  Counter as chanStatInputOverruns  
  Counter as chanStatParityErrors  
  INTEGER as chanStatTerminalType  
  INTEGER as chanStatCircuitType  
  INTEGER as chanStatOptions  
  INTEGER as chanStatBuffers  
  INTEGER as chanStatDiscMode  
  INTEGER as chanStatMenuNumber  
  INTEGER as chanStatHelpNumber  
  INTEGER as chanStatNewsNumber  
  INTEGER as chanStatPadRecall  
  INTEGER as chanStatEcho  
  INTEGER as chanStatDataForwarding  
  INTEGER as chanStatDelay  
  INTEGER as chanStatDRI  
  INTEGER as chanStatPadSignals  
  INTEGER as chanStatBreak  
  INTEGER as chanStatPadding  
  INTEGER as chanStatFold  
  INTEGER as chanStatDRO  
  INTEGER as chanStatLFI  
  INTEGER as chanStatLFPad  
  INTEGER as chanStatEdit  
  INTEGER as chanStatCharDel  
  INTEGER as chanStatBufferDel  
  INTEGER as chanStatDisp  
  INTEGER as chanStatEditServiceSignals  
  INTEGER as chanStatEchoMask  
  INTEGER as chanStatParityTreatment  
  INTEGER as chanStatPageWait  
  INTEGER as chanStatForce  
  INTEGER as chanStatBreakChar  
  INTEGER as chanStatNetworkParity  
  INTEGER as chanStatEscapeDelay  
  DisplayString as chanStatDestTsap  
  INTEGER as chanStatTransportLevelState  
  INTEGER as chanStatLinkState  
  INTEGER as chanStatProtocolState  
  INTEGER as chanStatProtocol  
  INTEGER as chanStatIdentity  
  Counter as chanStatDlciRxDe  
  Counter as chanStatDlciTxDe  
  Counter as chanStatDlciRxFecn  
  Counter as chanStatDlciTxFecn  
  Counter as chanStatDlciRxBecn  
  Counter as chanStatDlciTxBecn  
  INTEGER as chanStatConnectedToControllerIndex  

ChanParamEntry  
SEQUENCE    
  INTEGER as chanParamIndex  
  DisplayString as chanParamName  
  DisplayString as chanParamDRCMask  
  INTEGER as chanParamTerminalType  
  INTEGER as chanParamCircuitType  
  INTEGER as chanParamOptions  
  INTEGER as chanParamBuffers  
  INTEGER as chanParamDiscMode  
  INTEGER as chanParamMenuNumber  
  INTEGER as chanParamHelpNumber  
  INTEGER as chanParamNewsNumber  
  INTEGER as chanParamCallPriority  
  INTEGER as chanParamResourcePriority  
  INTEGER as chanParamPadEnable  
  INTEGER as chanParamPadRecall  
  INTEGER as chanParamEcho  
  INTEGER as chanParamDataForwarding  
  INTEGER as chanParamDelay  
  INTEGER as chanParamDRI  
  INTEGER as chanParamPadSignals  
  INTEGER as chanParamBreak  
  INTEGER as chanParamPadding  
  INTEGER as chanParamFold  
  INTEGER as chanParamDRO  
  INTEGER as chanParamLFI  
  INTEGER as chanParamLFPad  
  INTEGER as chanParamEdit  
  INTEGER as chanParamCharDel  
  INTEGER as chanParamBufferDel  
  INTEGER as chanParamDisp  
  INTEGER as chanParamEditServiceSignals  
  INTEGER as chanParamEchoMask  
  INTEGER as chanParamParityTreatment  
  INTEGER as chanParamPageWait  
  INTEGER as chanParamForce  
  INTEGER as chanParamBreakChar  
  INTEGER as chanParamNetworkParity  
  INTEGER as chanParamEscapeDelay  
  INTEGER as chanParamStationAddress  
  INTEGER as chanParamProvideXID  
  INTEGER as chanParamMode  
  INTEGER as chanParamPortMatch  
  INTEGER as chanParamReverseTelnetPort  
  INTEGER as chanParamBroadcastFilterTimer  
  INTEGER as chanParamInhibitLearning  
  INTEGER as chanParamRetainSession  
  INTEGER as chanParamPrinterType  
  INTEGER as chanParamScreenPrinter  
  INTEGER as chanParamLocalPrinter  
  INTEGER as chanParamInterlockBind  
  INTEGER as chanParamRedirectPrintTo  
  INTEGER as chanParamLUBase  
  INTEGER as chanParamLUOffset  
  INTEGER as chanParamLUTotal  
  INTEGER as chanParamDlciBase  
  INTEGER as chanParamDlciAdjacentBase  
  INTEGER as chanParamDlciPriority  
  INTEGER as chanParamDlciATM  
  INTEGER as chanParamDlciCir  
  INTEGER as chanParamDlciBc  
  INTEGER as chanParamDlciBe  
  INTEGER as chanParamDlciDe  
  INTEGER as chanParamDlciProtocol  
  INTEGER as chanParamDlciDsap  
  INTEGER as chanParamDlciSsap  
  INTEGER as chanParamDlciPutype  

X25Entry  
SEQUENCE    
  INTEGER as x25Index  
  DisplayString as x25Name  
  INTEGER as x25AddressGroup  
  DisplayString as x25Address  
  DisplayString as x25UserData  

NameEntry  
SEQUENCE    
  INTEGER as nameIndex  
  DisplayString as nameName  
  DisplayString as nameDRCMask  
  INTEGER as nameCallPriority  
  INTEGER as nameBilling  
  INTEGER as nameOptions  

MacEntry  
SEQUENCE    
  INTEGER as macIndex  
  DisplayString as macName  
  INTEGER as macFunction  
  INTEGER as macOptions  
  DisplayString as macSelector  
  DisplayString as macGenerator  

IlanEntry  
SEQUENCE    
  INTEGER as ilanIndex  
  DisplayString as ilanName  
  INTEGER as ilanOptions  
  DisplayString as ilanEthernetAddress  
  DisplayString as ilanTSAP  

ElogEntry  
SEQUENCE    
  INTEGER as elogIndex  
  DisplayString as elogRecord