SMON-MIB

File: SMON-MIB.mib (48652 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC RMON-MIB
RMON2-MIB IF-MIB SNMPv2-CONF

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Integer32 Counter64 RowStatus
TEXTUAL-CONVENTION rmon OwnerString
LastCreateTime DataSource rmonConformance
probeConfig InterfaceIndex MODULE-COMPLIANCE
OBJECT-GROUP

Defined Objects

smonCapabilities 1.3.6.1.2.1.16.19.15
An indication of the SMON MIB groups supported by this agent.
OBJECT-TYPE    
  BITS smonVlanStats(0), smonPrioStats(1), dataSource(2), smonUnusedBit(3), portCopy(4)  

smonMIBCompliances 1.3.6.1.2.1.16.20.3
OBJECT IDENTIFIER    

smonMIBCompliance 1.3.6.1.2.1.16.20.3.1
Describes the requirements for full conformance with the SMON MIB
MODULE-COMPLIANCE    

smonMIBVlanStatsCompliance 1.3.6.1.2.1.16.20.3.2
Describes the requirements for conformance with the SMON MIB with support for VLAN Statistics. Mandatory for a SMON probe in environment where IEEE 802.1Q bridging is implemented.
MODULE-COMPLIANCE    

smonMIBPrioStatsCompliance 1.3.6.1.2.1.16.20.3.3
Describes the requirements for conformance with the SMON MIB with support for priority level Statistics. Mandatory for a SMON probe in a environment where IEEE 802.1p priority-switching is implemented.
MODULE-COMPLIANCE    

portCopyCompliance 1.3.6.1.2.1.16.20.3.4
Describes the requirements for conformance with the port copy functionality defined by the SMON MIB
MODULE-COMPLIANCE    

smonMIBGroups 1.3.6.1.2.1.16.20.4
OBJECT IDENTIFIER    

dataSourceCapsGroup 1.3.6.1.2.1.16.20.4.1
Defines the objects that describe the capabilities of RMON data sources.
OBJECT-GROUP    

smonVlanStatsGroup 1.3.6.1.2.1.16.20.4.2
Defines the switch monitoring specific statistics - per VLAN Id on interfaces of 10MB or less.
OBJECT-GROUP    

smonPrioStatsGroup 1.3.6.1.2.1.16.20.4.3
Defines the switch monitoring specific statistics - per VLAN Id on interface.
OBJECT-GROUP    

smonHcTo100mbGroup 1.3.6.1.2.1.16.20.4.4
Defines the additional high capacity statistics needed to be kept on interfaces with ifSpeed greater than 10MB/sec and less than or equal to 100MB/sec.
OBJECT-GROUP    

smonHc100mbPlusGroup 1.3.6.1.2.1.16.20.4.5
Defines the additional high capacity statistics needed to be kept on interfaces with ifSpeed of more than 100MB/sec. These statistics MUST also be kept on smonDataSources of type VLAN or entPhysicalEntry.
OBJECT-GROUP    

hcVlanTo100mbGroup 1.3.6.1.2.1.16.20.4.6
Defines the additional high capacity VLAN statistics needed to be kept on interfaces with ifSpeed greater than 10MB/sec and less than or equal to 100MB/sec.
OBJECT-GROUP    

hcVlan100mbPlusGroup 1.3.6.1.2.1.16.20.4.7
Defines the additional high capacity VLAN statistics needed to be kept on interfaces with ifSpeed of more than 100MB/sec. These statistics MUST also be kept on smonDataSources of type VLAN or entPhysicalEntry.
OBJECT-GROUP    

hcPrioTo100mbGroup 1.3.6.1.2.1.16.20.4.8
Defines the additional high capacity VLAN priority statistics needed to be kept on interfaces with ifSpeed of greater than 10MB/sec and less than or equal to 100MB/sec.
OBJECT-GROUP    

hcPrio100mbPlusGroup 1.3.6.1.2.1.16.20.4.9
Defines the additional high capacity VLAN priority statistics needed to be kept on interfaces with ifSpeed of greater than 100MB/sec. These statistics MUST also be kept on smonDataSources of type VLAN or entPhysicalEntry.
OBJECT-GROUP    

smonVlanStatsExtGroup 1.3.6.1.2.1.16.20.4.10
Defines the switch monitoring specific statistics for systems capable of counting non-unicast octets for a given dataSource (as described in the dataSourceRmonCaps object).
OBJECT-GROUP    

smonInformationGroup 1.3.6.1.2.1.16.20.4.11
An indication of the SMON capabilities supported by this agent.
OBJECT-GROUP    

portCopyConfigGroup 1.3.6.1.2.1.16.20.4.12
Defines the control objects for copy port operations.
OBJECT-GROUP    

switchRMON 1.3.6.1.2.1.16.22
The MIB module for managing remote monitoring device implementations for Switched Networks
MODULE-IDENTITY    

smonMIBObjects 1.3.6.1.2.1.16.22.1
OBJECT IDENTIFIER    

dataSourceCaps 1.3.6.1.2.1.16.22.1.1
OBJECT IDENTIFIER    

dataSourceCapsTable 1.3.6.1.2.1.16.22.1.1.1
This table describes RMON data sources and port copy capabilities. An NMS MAY use this table to discover the identity and attributes of the data sources on a given agent implementation. Similar to the probeCapabilities object, actual row-creation operations will succeed or fail based on the resources available and parameter values used in each row-creation operation. Upon restart of the RMON agent, the dataSourceTable, ifTable, and perhaps entPhysicalTable are initialized for the available dataSources. For each dataSourceCapsEntry representing a VLAN or entPhysicalEntry the agent MUST create an associated ifEntry with a ifType value of 'propVirtual(53)'. This ifEntry will be used as the actual value in RMON control table dataSource objects. The assigned ifIndex value is copied into the associated dataSourceCapsIfIndex object. It is understood that dataSources representing VLANs may not always be instantiated immediately upon restart, but rather as VLAN usage is detected by the agent. The agent SHOULD attempt to create dataSource and interface entries for all dataSources as soon as possible.
OBJECT-TYPE    
  SEQUENCE OF  
    DataSourceCapsEntry

dataSourceCapsEntry 1.3.6.1.2.1.16.22.1.1.1.1
Entries per data source containing descriptions of data source and port copy capabilities. This table is populated by the SMON agent with one entry for each supported data source.
OBJECT-TYPE    
  DataSourceCapsEntry  

dataSourceCapsObject 1.3.6.1.2.1.16.22.1.1.1.1.1
Defines an object that can be a SMON data source or a source or a destination for a port copy operation.
OBJECT-TYPE    
  SmonDataSource  

dataSourceRmonCaps 1.3.6.1.2.1.16.22.1.1.1.1.2
General attributes of the specified dataSource. Note that these are static attributes, which SHOULD NOT be adjusted because of current resources or configuration. - countErrFrames(0) The agent sets this bit for the dataSource if errored frames received on this dataSource can actually be monitored by the agent The agent clears this bit if any errored frames are not visible to the RMON data collector. - countAllGoodFrames(1) The agent sets this bit for the dataSource if all good frames received on this dataSource can actually be monitored by the agent. The agent clears this bit if any good frames are not visible for RMON collection, e.g., the dataSource is a non-promiscuous interface or an internal switch interface which may not receive frames which were switched in hardware or dropped by the bridge forwarding function. - countAnyRmonTables(2) The agent sets this bit if this dataSource can actually be used in any of the implemented RMON tables, resources notwithstanding. The agent clears this bit if this dataSourceCapsEntry is present simply to identify a dataSource that may only be used as portCopySource and/or a portCopyDest, but not the source of an actual RMON data collection. - babyGiantsCountAsGood(3) The agent sets this bit if it can distinguish, for counting purposes, between true giant frames and frames that exceed Ethernet maximum frame size 1518 due to VLAN tagging ('baby giants'). Specifically, this BIT means that frames up to 1522 octets are counted as good. Agents not capable of detecting 'baby giants' will clear this bit and will view all frames less than or equal to 1518 octets as 'good frames' and all frames larger than 1518 octets as 'bad frames' for the purpose of counting in the smonVlanIdStats and smonPrioStats tables. Agents capable of detecting 'baby giants' SHALL consider them as 'good frames' for the purpose of counting in the smonVlanIdStats and smonPrioStats tables.
OBJECT-TYPE    
  BITS countErrFrames(0), countAllGoodFrames(1), countAnyRmonTables(2), babyGiantsCountAsGood(3)  

dataSourceCopyCaps 1.3.6.1.2.1.16.22.1.1.1.1.3
PortCopy function capabilities of the specified dataSource. Note that these are static capabilities, which SHOULD NOT be adjusted because of current resources or configuration. - copySourcePort(0) The agent sets this bit if this dataSource is capable of acting as a source of a portCopy operation. The agent clears this bit otherwise. - copyDestPort(1) The agent sets this bit if this dataSource is capable of acting as a destination of a portCopy operation. The agent clears this bit otherwise. - copySrcTxTraffic(2) If the copySourcePort bit is set: The agent sets this bit if this dataSource is capable of copying frames transmitted out this portCopy source. The agent clears this bit otherwise. This function is needed to support full-duplex ports. Else: this bit SHOULD be cleared. - copySrcRxTraffic(3) If the copySourcePort bit is set: The agent sets this bit if this dataSource is capable of copying frames received on this portCopy source. The agent clears this bit otherwise. This function is needed to support full-duplex ports. Else: this bit SHOULD be cleared. - countDestDropEvents(4) If the copyDestPort bit is set: The agent sets this bit if it is capable of incrementing portCopyDestDropEvents, when this dataSource is the target of a portCopy operation and a frame destined to this dataSource is dropped (for RMON counting purposes). Else: this BIT SHOULD be cleared. - copyErrFrames(5) If the copySourcePort bit is set: The agent sets this bit if it is capable of copying all errored frames from this portCopy source-port, for errored frames received on this dataSource. Else: this BIT SHOULD be cleared. - copyUnalteredFrames(6) If the copySourcePort bit is set: The agent sets the copyUnalteredFrames bit If it is capable of copying all frames from this portCopy source-port without alteration in any way; Else: this bit SHOULD be cleared. - copyAllGoodFrames(7) If the copySourcePort bit is set: The agent sets this bit for the dataSource if all good frames received on this dataSource are normally capable of being copied by the agent. The agent clears this bit if any good frames are not visible for the RMON portCopy operation, e.g., the dataSource is a non-promiscuous interface or an internal switch interface which may not receive frames which were switched in hardware or dropped by the bridge forwarding function. Else: this bit SHOULD be cleared.
OBJECT-TYPE    
  BITS copySourcePort(0), copyDestPort(1), copySrcTxTraffic(2), copySrcRxTraffic(3), countDestDropEvents(4), copyErrFrames(5), copyUnalteredFrames(6), copyAllGoodFrames(7)  

dataSourceCapsIfIndex 1.3.6.1.2.1.16.22.1.1.1.1.4
This object contains the ifIndex value of the ifEntry associated with this smonDataSource. The agent MUST create 'propVirtual' ifEntries for each dataSourceCapsEntry of type VLAN or entPhysicalEntry.
OBJECT-TYPE    
  InterfaceIndex  

smonStats 1.3.6.1.2.1.16.22.1.2
OBJECT IDENTIFIER    

smonVlanStatsControlTable 1.3.6.1.2.1.16.22.1.2.1
Controls the setup of VLAN statistics tables. The statistics collected represent a distribution based on the IEEE 802.1Q VLAN-ID (VID), for each good frame attributed to the data source for the collection.
OBJECT-TYPE    
  SEQUENCE OF  
    SmonVlanStatsControlEntry

smonVlanStatsControlEntry 1.3.6.1.2.1.16.22.1.2.1.1
A conceptual row in the smonVlanStatsControlTable.
OBJECT-TYPE    
  SmonVlanStatsControlEntry  

smonVlanStatsControlIndex 1.3.6.1.2.1.16.22.1.2.1.1.1
A unique arbitrary index for this smonVlanStatsControlEntry.
OBJECT-TYPE    
  Integer32 1..65535  

smonVlanStatsControlDataSource 1.3.6.1.2.1.16.22.1.2.1.1.2
The source of data for this set of VLAN statistics. This object MAY NOT be modified if the associated smonVlanStatsControlStatus object is equal to active(1).
OBJECT-TYPE    
  DataSource  

smonVlanStatsControlCreateTime 1.3.6.1.2.1.16.22.1.2.1.1.3
The value of sysUpTime when this control entry was last activated. This object allows to a management station to detect deletion and recreation cycles between polls.
OBJECT-TYPE    
  LastCreateTime  

smonVlanStatsControlOwner 1.3.6.1.2.1.16.22.1.2.1.1.4
Administratively assigned named of the owner of this entry. It usually defines the entity that created this entry and is therefore using the resources assigned to it, though there is no enforcement mechanism, nor assurance that rows created are ever used.
OBJECT-TYPE    
  OwnerString  

smonVlanStatsControlStatus 1.3.6.1.2.1.16.22.1.2.1.1.5
The status of this row. An entry MAY NOT exist in the active state unless all objects in the entry have an appropriate value. If this object is not equal to active(1), all associated entries in the smonVlanIdStatsTable SHALL be deleted.
OBJECT-TYPE    
  RowStatus  

smonVlanIdStatsTable 1.3.6.1.2.1.16.22.1.2.2
Contains the VLAN statistics data. The statistics collected represent a distribution based on the IEEE 802.1Q VLAN-ID (VID), for each good frame attributed to the data source for the collection. This function applies the same rules for attributing frames to VLAN-based collections. RMON VLAN statistics are collected after the Ingress Rules defined in section 3.13 of the VLAN Specification [20] are applied. It is possible that entries in this table will be garbage-collected, based on agent resources, and VLAN configuration. Agents are encouraged to support all 4094 index values and not garbage collect this table.
OBJECT-TYPE    
  SEQUENCE OF  
    SmonVlanIdStatsEntry

smonVlanIdStatsEntry 1.3.6.1.2.1.16.22.1.2.2.1
A conceptual row in smonVlanIdStatsTable.
OBJECT-TYPE    
  SmonVlanIdStatsEntry  

smonVlanIdStatsId 1.3.6.1.2.1.16.22.1.2.2.1.1
The unique identifier of the VLAN monitored for this specific statistics collection. Tagged packets match the VID for the range between 1 and 4094. An external RMON probe MAY detect VID=0 on an Inter Switch Link, in which case the packet belongs to a VLAN determined by the PVID of the ingress port. The VLAN to which such a packet belongs can be determined only by a RMON probe internal to the switch.
OBJECT-TYPE    
  Integer32 1..4094  

smonVlanIdStatsTotalPkts 1.3.6.1.2.1.16.22.1.2.2.1.2
The total number of packets counted on this VLAN.
OBJECT-TYPE    
  Counter32  

smonVlanIdStatsTotalOverflowPkts 1.3.6.1.2.1.16.22.1.2.2.1.3
The number of times the associated smonVlanIdStatsTotalPkts counter has overflowed.
OBJECT-TYPE    
  Counter32  

smonVlanIdStatsTotalHCPkts 1.3.6.1.2.1.16.22.1.2.2.1.4
The total number of packets counted on this VLAN.
OBJECT-TYPE    
  Counter64  

smonVlanIdStatsTotalOctets 1.3.6.1.2.1.16.22.1.2.2.1.5
The total number of octets counted on this VLAN.
OBJECT-TYPE    
  Counter32  

smonVlanIdStatsTotalOverflowOctets 1.3.6.1.2.1.16.22.1.2.2.1.6
The number of times the associated smonVlanIdStatsTotalOctets counter has overflowed.
OBJECT-TYPE    
  Counter32  

smonVlanIdStatsTotalHCOctets 1.3.6.1.2.1.16.22.1.2.2.1.7
The total number of octets counted on this VLAN.
OBJECT-TYPE    
  Counter64  

smonVlanIdStatsNUcastPkts 1.3.6.1.2.1.16.22.1.2.2.1.8
The total number of non-unicast packets counted on this VLAN.
OBJECT-TYPE    
  Counter32  

smonVlanIdStatsNUcastOverflowPkts 1.3.6.1.2.1.16.22.1.2.2.1.9
The number of times the associated smonVlanIdStatsNUcastPkts counter has overflowed.
OBJECT-TYPE    
  Counter32  

smonVlanIdStatsNUcastHCPkts 1.3.6.1.2.1.16.22.1.2.2.1.10
The total number of non-unicast packets counted on this VLAN.
OBJECT-TYPE    
  Counter64  

smonVlanIdStatsNUcastOctets 1.3.6.1.2.1.16.22.1.2.2.1.11
The total number of non-unicast octets counted on this VLAN.
OBJECT-TYPE    
  Counter32  

smonVlanIdStatsNUcastOverflowOctets 1.3.6.1.2.1.16.22.1.2.2.1.12
The number of times the associated smonVlanIdStatsNUcastOctets counter has overflowed.
OBJECT-TYPE    
  Counter32  

smonVlanIdStatsNUcastHCOctets 1.3.6.1.2.1.16.22.1.2.2.1.13
The total number of Non-unicast octets counted on this VLAN.
OBJECT-TYPE    
  Counter64  

smonVlanIdStatsCreateTime 1.3.6.1.2.1.16.22.1.2.2.1.14
The value of sysUpTime when this entry was last activated. This object allows to a management station to detect deletion and recreation cycles between polls.
OBJECT-TYPE    
  LastCreateTime  

smonPrioStatsControlTable 1.3.6.1.2.1.16.22.1.2.3
Controls the setup of priority statistics tables. The smonPrioStatsControlTable allows configuration of collections based on the value of the 3-bit user priority field encoded in the Tag Control Information (TCI) field according to [19],[20]. Note that this table merely reports priority as encoded in the VLAN headers, not the priority (if any) given to the frame for the actual switching purposes.
OBJECT-TYPE    
  SEQUENCE OF  
    SmonPrioStatsControlEntry

smonPrioStatsControlEntry 1.3.6.1.2.1.16.22.1.2.3.1
A conceptual row in the smonPrioStatsControlTable.
OBJECT-TYPE    
  SmonPrioStatsControlEntry  

smonPrioStatsControlIndex 1.3.6.1.2.1.16.22.1.2.3.1.1
A unique arbitrary index for this smonPrioStatsControlEntry.
OBJECT-TYPE    
  Integer32 1..65535  

smonPrioStatsControlDataSource 1.3.6.1.2.1.16.22.1.2.3.1.2
The source of data for this set of VLAN statistics. This object MAY NOT be modified if the associated smonPrioStatsControlStatus object is equal to active(1).
OBJECT-TYPE    
  DataSource  

smonPrioStatsControlCreateTime 1.3.6.1.2.1.16.22.1.2.3.1.3
The value of sysUpTime when this entry was created. This object allows to a management station to detect deletion and recreation cycles between polls.
OBJECT-TYPE    
  LastCreateTime  

smonPrioStatsControlOwner 1.3.6.1.2.1.16.22.1.2.3.1.4
Administratively assigned named of the owner of this entry. It usually defines the entity that created this entry and is therefore using the resources assigned to it, though there is no enforcement mechanism, nor assurance that rows created are ever used.
OBJECT-TYPE    
  OwnerString  

smonPrioStatsControlStatus 1.3.6.1.2.1.16.22.1.2.3.1.5
The status of this row. An entry MAY NOT exist in the active state unless all objects in the entry have an appropriate value. If this object is not equal to active(1), all associated entries in the smonPrioStatsTable SHALL be deleted.
OBJECT-TYPE    
  RowStatus  

smonPrioStatsTable 1.3.6.1.2.1.16.22.1.2.4
Contains the priority statistics. The collections are based on the value of the 3-bit user priority field encoded in the Tag Control Information (TCI) field according to [19], [20]. Note that this table merely reports priority as encoded in the VLAN headers, not the priority (if any) given to the frame for the actual switching purposes. No garbage collection is designed for this table, as there always are at most eight rows per statistical set, and the low memory requirements do not justify the implementation of such a mechanism.
OBJECT-TYPE    
  SEQUENCE OF  
    SmonPrioStatsEntry

smonPrioStatsEntry 1.3.6.1.2.1.16.22.1.2.4.1
A conceptual row in smonPrioStatsTable.
OBJECT-TYPE    
  SmonPrioStatsEntry  

smonPrioStatsId 1.3.6.1.2.1.16.22.1.2.4.1.1
The unique identifier of the priority level monitored for this specific statistics collection.
OBJECT-TYPE    
  Integer32 0..7  

smonPrioStatsPkts 1.3.6.1.2.1.16.22.1.2.4.1.2
The total number of packets counted on this priority level.
OBJECT-TYPE    
  Counter32  

smonPrioStatsOverflowPkts 1.3.6.1.2.1.16.22.1.2.4.1.3
The number of times the associated smonPrioStatsPkts counter has overflowed.
OBJECT-TYPE    
  Counter32  

smonPrioStatsHCPkts 1.3.6.1.2.1.16.22.1.2.4.1.4
The total number of packets counted on this priority level.
OBJECT-TYPE    
  Counter64  

smonPrioStatsOctets 1.3.6.1.2.1.16.22.1.2.4.1.5
The total number of octets counted on this priority level.
OBJECT-TYPE    
  Counter32  

smonPrioStatsOverflowOctets 1.3.6.1.2.1.16.22.1.2.4.1.6
The number of times the associated smonPrioStatsOctets counter has overflowed.
OBJECT-TYPE    
  Counter32  

smonPrioStatsHCOctets 1.3.6.1.2.1.16.22.1.2.4.1.7
The total number of octets counted on this priority level.
OBJECT-TYPE    
  Counter64  

portCopyConfig 1.3.6.1.2.1.16.22.1.3
OBJECT IDENTIFIER    

portCopyTable 1.3.6.1.2.1.16.22.1.3.1
Port Copy provides the ability to copy all frames from a specified source to specified destination within a switch. Source and destinations MUST be ifEntries, as defined by [22]. One to one, one to many, many to one and many to many source to destination relationships may be configured. Applicable counters on the destination will increment for all packets transiting the port, be it by normal bridging/switching or due to packet copy. Note that this table manages no RMON data collection by itself, and an agent may possibly implement no RMON objects except objects related to the port copy operation defined by the portCopyCompliance conformance macro. That allows for a switch with no other embedded RMON capability to perform port copy operations to a destination port at which a different external RMON probe is connected. One to one, many to one and one to many source to destination relationships may be configured. Each row that exists in this table defines such a relationship. By disabling a row in this table the port copy relationship no longer exists. The number of entries and the types of port copies (1-1, many-1, 1-many) are implementation specific and could possibly be dynamic due to changing resource availability. In order to configure a source to destination portCopy relationship, both source and destination interfaces MUST be present as an ifEntry in the ifTable and their respective ifAdminStatus and ifOperStatus values MUST be equal to 'up(1)'. If the value of any of those two objects changes after the portCopyEntry is activated, portCopyStatus will transition to 'notReady(3)'. The capability of an interface to be source or destination of a port copy operation is described by the 'copySourcePort(0)' and 'copyDestPort(1)' bits in dataSourceCopyCaps. Those bits SHOULD be appropriately set by the agent, in order to allow for a portCopyEntry to be created. Applicable counters on the destination will increment for all packets transmitted, be it by normal bridging/switching or due to packet copy.
OBJECT-TYPE    
  SEQUENCE OF  
    PortCopyEntry

portCopyEntry 1.3.6.1.2.1.16.22.1.3.1.1
Describes a particular port copy entry.
OBJECT-TYPE    
  PortCopyEntry  

portCopySource 1.3.6.1.2.1.16.22.1.3.1.1.1
The ifIndex of the source which will have all packets redirected to the destination as defined by portCopyDest.
OBJECT-TYPE    
  InterfaceIndex  

portCopyDest 1.3.6.1.2.1.16.22.1.3.1.1.2
Defines the ifIndex destination for the copy operation.
OBJECT-TYPE    
  InterfaceIndex  

portCopyDestDropEvents 1.3.6.1.2.1.16.22.1.3.1.1.3
The total number of events in which port copy packets were dropped by the switch at the destination port due to lack of resources. Note that this number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected. A single dropped event counter is maintained for each portCopyDest. Thus all instances associated with a given portCopyDest will have the same portCopyDestDropEvents value.
OBJECT-TYPE    
  Counter32  

portCopyDirection 1.3.6.1.2.1.16.22.1.3.1.1.4
This object affects the way traffic is copied from a switch source port, for the indicated port copy operation. If this object has the value 'copyRxOnly(1)', then only traffic received on the indicated source port will be copied to the indicated destination port. If this object has the value 'copyTxOnly(2)', then only traffic transmitted out the indicated source port will be copied to the indicated destination port. If this object has the value 'copyBoth(3)', then all traffic received or transmitted on the indicated source port will be copied to the indicated destination port. The creation and deletion of instances of this object is controlled by the portCopyRowStatus object. Note that there is no guarantee that changes in the value of this object performed while the associated portCopyRowStatus object is equal to active will not cause traffic discontinuities in the packet stream.
OBJECT-TYPE    
  INTEGER copyRxOnly(1), copyTxOnly(2), copyBoth(3)  

portCopyStatus 1.3.6.1.2.1.16.22.1.3.1.1.5
Defines the status of the port copy entry. In order to configure a source to destination portCopy relationship, both source and destination interfaces MUST be present as an ifEntry in the ifTable and their respective ifAdminStatus and ifOperStatus values MUST be equal to 'up(1)'. If the value of any of those two objects changes after the portCopyEntry is activated, portCopyStatus will transition to 'notReady(3)'. The capability of an interface to be source or destination of a port copy operation is described by the 'copySourcePort(0)' and 'copyDestPort(1)' bits in dataSourceCopyCaps. Those bits SHOULD be appropriately set by the agent, in order to allow for a portCopyEntry to be created.
OBJECT-TYPE    
  RowStatus  

smonRegistrationPoints 1.3.6.1.2.1.16.22.1.4
OBJECT IDENTIFIER    

smonVlanDataSource 1.3.6.1.2.1.16.22.1.4.1
OBJECT IDENTIFIER    

Defined Objects

SmonDataSource  
Identifies the source of the data that the associated function is configured to analyze. This Textual Convention extends the DataSource Textual Convention defined by RMON 2 to the following data source types: - ifIndex. DataSources of this traditional form are called 'port-based', but only if ifType. is not equal to 'propVirtual(53)'. - smonVlanDataSource. A dataSource of this form refers to a 'Packet-based VLAN' and is called a 'VLAN-based' dataSource. is the VLAN ID as defined by the IEEE 802.1Q standard [19]. The value is between 1 and 4094 inclusive, and it represents an 802.1Q VLAN-ID with global scope within a given bridged domain, as defined by [19]. - entPhysicalEntry. A dataSource of this form refers to a physical entity within the agent (e.g. entPhysicalClass = backplane(4)) and is called an 'entity-based' dataSource.
TEXTUAL-CONVENTION    
  OBJECT IDENTIFIER  

DataSourceCapsEntry  
SEQUENCE    
  SmonDataSource as dataSourceCapsObject  
  BITS as dataSourceRmonCaps  
  BITS as dataSourceCopyCaps  
  InterfaceIndex as dataSourceCapsIfIndex  

SmonVlanStatsControlEntry  
SEQUENCE    
  Integer32 as smonVlanStatsControlIndex  
  DataSource as smonVlanStatsControlDataSource  
  LastCreateTime as smonVlanStatsControlCreateTime  
  OwnerString as smonVlanStatsControlOwner  
  RowStatus as smonVlanStatsControlStatus  

SmonVlanIdStatsEntry  
SEQUENCE    
  Integer32 as smonVlanIdStatsId  
  Counter32 as smonVlanIdStatsTotalPkts  
  Counter32 as smonVlanIdStatsTotalOverflowPkts  
  Counter64 as smonVlanIdStatsTotalHCPkts  
  Counter32 as smonVlanIdStatsTotalOctets  
  Counter32 as smonVlanIdStatsTotalOverflowOctets  
  Counter64 as smonVlanIdStatsTotalHCOctets  
  Counter32 as smonVlanIdStatsNUcastPkts  
  Counter32 as smonVlanIdStatsNUcastOverflowPkts  
  Counter64 as smonVlanIdStatsNUcastHCPkts  
  Counter32 as smonVlanIdStatsNUcastOctets  
  Counter32 as smonVlanIdStatsNUcastOverflowOctets  
  Counter64 as smonVlanIdStatsNUcastHCOctets  
  LastCreateTime as smonVlanIdStatsCreateTime  

SmonPrioStatsControlEntry  
SEQUENCE    
  Integer32 as smonPrioStatsControlIndex  
  DataSource as smonPrioStatsControlDataSource  
  LastCreateTime as smonPrioStatsControlCreateTime  
  OwnerString as smonPrioStatsControlOwner  
  RowStatus as smonPrioStatsControlStatus  

SmonPrioStatsEntry  
SEQUENCE    
  Integer32 as smonPrioStatsId  
  Counter32 as smonPrioStatsPkts  
  Counter32 as smonPrioStatsOverflowPkts  
  Counter64 as smonPrioStatsHCPkts  
  Counter32 as smonPrioStatsOctets  
  Counter32 as smonPrioStatsOverflowOctets  
  Counter64 as smonPrioStatsHCOctets  

PortCopyEntry  
SEQUENCE    
  InterfaceIndex as portCopySource  
  InterfaceIndex as portCopyDest  
  Counter32 as portCopyDestDropEvents  
  INTEGER as portCopyDirection  
  RowStatus as portCopyStatus