
SNMP-TARGET-MIB
File:
SNMP-TARGET-MIB.mib (25334 bytes)
Imported modules
Imported symbols
Defined Objects
| snmpTargetMIB |
1.3.6.1.6.3.12 |
| This MIB module defines MIB objects which provide mechanisms to remotely configure the parameters used by an SNMP entity for the generation of SNMP messages. |
| MODULE-IDENTITY |
|
|
|
| snmpTargetSpinLock |
1.3.6.1.6.3.12.1.1 |
| This object is used to facilitate modification of table entries in the SNMP-TARGET-MIB module by multiple managers. In particular, it is useful when modifying the value of the snmpTargetAddrTagList object. The procedure for modifying the snmpTargetAddrTagList object is as follows: 1. Retrieve the value of snmpTargetSpinLock and of snmpTargetAddrTagList. 2. Generate a new value for snmpTargetAddrTagList. 3. Set the value of snmpTargetSpinLock to the retrieved value, and the value of snmpTargetAddrTagList to the new value. If the set fails for the snmpTargetSpinLock object, go back to step 1. |
| OBJECT-TYPE |
|
|
|
| |
TestAndIncr |
|
|
| snmpTargetAddrEntry |
1.3.6.1.6.3.12.1.2.1 |
| A transport address to be used in the generation of SNMP operations. Entries in the snmpTargetAddrTable are created and deleted using the snmpTargetAddrRowStatus object. |
| OBJECT-TYPE |
|
|
|
| |
SnmpTargetAddrEntry |
|
|
| snmpTargetAddrTDomain |
1.3.6.1.6.3.12.1.2.1.2 |
| This object indicates the transport type of the address contained in the snmpTargetAddrTAddress object. |
| OBJECT-TYPE |
|
|
|
| |
TDomain |
|
|
| snmpTargetAddrTimeout |
1.3.6.1.6.3.12.1.2.1.4 |
| This object should reflect the expected maximum round trip time for communicating with the transport address defined by this row. When a message is sent to this address, and a response (if one is expected) is not received within this time period, an implementation may assume that the response will not be delivered. Note that the time interval that an application waits for a response may actually be derived from the value of this object. The method for deriving the actual time interval is implementation dependent. One such method is to derive the expected round trip time based on a particular retransmission algorithm and on the number of timeouts which have occurred. The type of message may also be considered when deriving expected round trip times for retransmissions. For example, if a message is being sent with a securityLevel that indicates both authentication and privacy, the derived value may be increased to compensate for extra processing time spent during authentication and encryption processing. |
| OBJECT-TYPE |
|
|
|
| |
TimeInterval |
|
|
| snmpTargetAddrRetryCount |
1.3.6.1.6.3.12.1.2.1.5 |
| This object specifies a default number of retries to be attempted when a response is not received for a generated message. An application may provide its own retry count, in which case the value of this object is ignored. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..255 |
|
| snmpTargetAddrParams |
1.3.6.1.6.3.12.1.2.1.7 |
| The value of this object identifies an entry in the snmpTargetParamsTable. The identified entry contains SNMP parameters to be used when generating messages to be sent to this transport address. |
| OBJECT-TYPE |
|
|
|
| |
SnmpAdminString |
SIZE(1..32) |
|
| snmpTargetAddrRowStatus |
1.3.6.1.6.3.12.1.2.1.9 |
| The status of this conceptual row. To create a row in this table, a manager must set this object to either createAndGo(4) or createAndWait(5). Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the snmpTargetAddrRowStatus column is 'notReady'. In particular, a newly created row cannot be made active until the corresponding instances of snmpTargetAddrTDomain, snmpTargetAddrTAddress, and snmpTargetAddrParams have all been set. The following objects may not be modified while the value of this object is active(1): - snmpTargetAddrTDomain - snmpTargetAddrTAddress An attempt to set these objects while the value of snmpTargetAddrRowStatus is active(1) will result in an inconsistentValue error. |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| snmpTargetParamsEntry |
1.3.6.1.6.3.12.1.3.1 |
| A set of SNMP target information. Entries in the snmpTargetParamsTable are created and deleted using the snmpTargetParamsRowStatus object. |
| OBJECT-TYPE |
|
|
|
| |
SnmpTargetParamsEntry |
|
|
| snmpTargetParamsSecurityModel |
1.3.6.1.6.3.12.1.3.1.3 |
| The Security Model to be used when generating SNMP messages using this entry. An implementation may choose to return an inconsistentValue error if an attempt is made to set this variable to a value for a security model which the implementation does not support. |
| OBJECT-TYPE |
|
|
|
| |
SnmpSecurityModel |
1..2147483647 |
|
| snmpTargetParamsRowStatus |
1.3.6.1.6.3.12.1.3.1.7 |
| The status of this conceptual row. To create a row in this table, a manager must set this object to either createAndGo(4) or createAndWait(5). Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the snmpTargetParamsRowStatus column is 'notReady'. In particular, a newly created row cannot be made active until the corresponding snmpTargetParamsMPModel, snmpTargetParamsSecurityModel, snmpTargetParamsSecurityName, and snmpTargetParamsSecurityLevel have all been set. The following objects may not be modified while the value of this object is active(1): - snmpTargetParamsMPModel - snmpTargetParamsSecurityModel - snmpTargetParamsSecurityName - snmpTargetParamsSecurityLevel An attempt to set these objects while the value of snmpTargetParamsRowStatus is active(1) will result in an inconsistentValue error. |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| snmpUnavailableContexts |
1.3.6.1.6.3.12.1.4 |
| The total number of packets received by the SNMP engine which were dropped because the context contained in the message was unavailable. |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| snmpUnknownContexts |
1.3.6.1.6.3.12.1.5 |
| The total number of packets received by the SNMP engine which were dropped because the context contained in the message was unknown. |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| snmpTargetResponseGroup |
1.3.6.1.6.3.12.3.2.2 |
| A collection of objects providing remote configuration of management targets for applications which generate SNMP messages for which a response message would be expected. |
| OBJECT-GROUP |
|
|
|
Defined Objects
| SnmpTagValue |
|
| An octet string containing a tag value. Tag values are preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 character encoding scheme described in RFC 2279. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. The use of control codes should be avoided, and certain control codes are not allowed as described below. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 representation is identical to the US-ASCII encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction must be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC1905]. An object of this type contains a single tag value which is used to select a set of entries in a table. A tag value is an arbitrary string of octets, but may not contain a delimiter character. Delimiter characters are defined to be one of the following: - An ASCII space character (0x20). - An ASCII TAB character (0x09). - An ASCII carriage return (CR) character (0x0D). - An ASCII line feed (LF) character (0x0B). Delimiter characters are used to separate tag values in a tag list. An object of this type may only contain a single tag value, and so delimiter characters are not allowed in a value of this type. Some examples of valid tag values are: - 'acme' - 'router' - 'host' The use of a tag value to select table entries is application and MIB specific. |
| TEXTUAL-CONVENTION |
|
|
|
| |
OCTET STRING |
SIZE(0..255) |
|
| SnmpTagList |
|
| An octet string containing a list of tag values. Tag values are preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 character encoding scheme described in RFC 2279. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. The use of control codes should be avoided, except as described below. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 representation is identical to the US-ASCII encoding. An object of this type contains a list of tag values which are used to select a set of entries in a table. A tag value is an arbitrary string of octets, but may not contain a delimiter character. Delimiter characters are defined to be one of the following: - An ASCII space character (0x20). - An ASCII TAB character (0x09). - An ASCII carriage return (CR) character (0x0D). - An ASCII line feed (LF) character (0x0B). Delimiter characters are used to separate tag values in a tag list. Only a single delimiter character may occur between two tag values. A tag value may not have a zero length. These constraints imply certain restrictions on the contents of this object: - There cannot be a leading or trailing delimiter character. - There cannot be multiple adjacent delimiter characters. Some examples of valid tag lists are: - An empty string - 'acme router' - 'host managerStation' Note that although a tag value may not have a length of zero, an empty string is still valid. This indicates an empty list (i.e. there are no tag values in the list). The use of the tag list to select table entries is application and MIB specific. Typically, an application will provide one or more tag values, and any entry which contains some combination of these tag values will be selected. |
| TEXTUAL-CONVENTION |
|
|
|
| |
OCTET STRING |
SIZE(0..255) |
|
| SnmpTargetAddrEntry |
|
| SEQUENCE |
|
|
|
| |
SnmpAdminString as snmpTargetAddrName |
|
|
| |
TDomain as snmpTargetAddrTDomain |
|
|
| |
TAddress as snmpTargetAddrTAddress |
|
|
| |
TimeInterval as snmpTargetAddrTimeout |
|
|
| |
Integer32 as snmpTargetAddrRetryCount |
|
|
| |
SnmpTagList as snmpTargetAddrTagList |
|
|
| |
SnmpAdminString as snmpTargetAddrParams |
|
|
| |
StorageType as snmpTargetAddrStorageType |
|
|
| |
RowStatus as snmpTargetAddrRowStatus |
|
|
| SnmpTargetParamsEntry |
|
| SEQUENCE |
|
|
|
| |
SnmpAdminString as snmpTargetParamsName |
|
|
| |
SnmpMessageProcessingModel as snmpTargetParamsMPModel |
|
|
| |
SnmpSecurityModel as snmpTargetParamsSecurityModel |
|
|
| |
SnmpAdminString as snmpTargetParamsSecurityName |
|
|
| |
SnmpSecurityLevel as snmpTargetParamsSecurityLevel |
|
|
| |
StorageType as snmpTargetParamsStorageType |
|
|
| |
RowStatus as snmpTargetParamsRowStatus |
|
|